CISCO-VISM-DSX0-MIB
83 objects
This MIB module contains ds0 configuration, Status and DS0 related information on a DS1 interface supported in VISM module. VISM is a Voice Interworking Service Module supported in MGX8250 and MGX8850 and other MGX products. Terminologies used: line : Same as the Physical Interface. DS1 line signifies DS1 interface.
Imported Objects
| BASIS-MIB | cardSpecific dsx0Vism |
| CISCOWAN-SMI | ciscoWan |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | DisplayString TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.351.110.3.24 | NodevismDs0CardStats | |||
| 1.3.6.1.4.1.351.110.3.24.1 | ScalarvismTotalDs0Count | read-only | current | This is the total number of ds0s configured the card. |
| 1.3.6.1.4.1.351.110.3.24.2 | ScalarvismFreeDs0Count | read-only | current | This is the number of free ds0s on the card. |
| 1.3.6.1.4.1.351.110.3.24.3 | ScalarvismActiveDs0Count | read-only | current | This is the number of active ds0s on the card. |
| 1.3.6.1.4.1.351.110.3.24.4 | ScalarvismBlockDs0Count | read-only | current | This is the number of blocked ds0s on the card. |
| 1.3.6.1.4.1.351.110.3.24.5 | ScalarvismActiveHighWaterMark | read-only | current | This is the high water mark number of ds0s that were active simultaneously on the card. |
| 1.3.6.1.4.1.351.110.3.24.6 | ScalarvismDs0CardStatsClrButton | read-write | current | This variable is used to clear all the vism Ds0 card stats. 1 = No action, 2 = Clear alarm |
| 1.3.6.1.4.1.351.110.4.7.1 | Tabledsx0VismCnfTable | not-accessible | current | The entries in this table are created and deleted implicitly at the time of adding and deleting the line. For every DS0 on a line, one row will be created. |
| 1.3.6.1.4.1.351.110.4.7.1.1 | Rowdsx0VismCnfEntry | not-accessible | current | This ds0 table contains both cas related and non cas related parameters. The non cas related parameters are applicable accross all line signaling types, while … |
| 1.3.6.1.4.1.351.110.4.7.1.1.1 | Columnds0IfIndex | read-only | current | This attribute defines the index for this table. This is derived from the following formula: index = 31 * (Ds1# - 1) + ds0# where : Ds1# - The T1/E1 line numbe… |
| 1.3.6.1.4.1.351.110.4.7.1.1.2 | Columnds0RobbedBitSignalling | read-write | current | This object indicates if Robbed Bit Signalling is turned on or off for a given ds0. This only applies to DS0s on a DS1 link. For E1 links the value is always o… |
| 1.3.6.1.4.1.351.110.4.7.1.1.3 | Columnds0IdleCode | read-write | current | This object contains the code transmitted in the ABCD bits when the ds0 is not connected and ds0TransmitCodesEnable is enabled. The object is a bitmap and the … |
| 1.3.6.1.4.1.351.110.4.7.1.1.4 | Columnds0SeizedCode | read-write | current | This object contains the code transmitted in the ABCD bits when the ds0 is connected and ds0TransmitCodesEnable is enabled. The object is a bitmap and the vari… |
| 1.3.6.1.4.1.351.110.4.7.1.1.5 | Columnds0ReceivedCode | read-only | current | This object contains the code being received in the ABCD bits. The object is a bitmap and the various bit positions are: Bit 0 (value 1) D bit Bit 1 (value 2) … |
| 1.3.6.1.4.1.351.110.4.7.1.1.6 | Columnds0TransmitCodesEnable | read-only | deprecated | This object determines if the idle and seized codes are transmitted. If the value of this object is true then the codes are transmitted. This object is not app… |
| 1.3.6.1.4.1.351.110.4.7.1.1.7 | Columnds0BundleMapped | read-only | current | This object indicates endpoint number as specified by mgEndpointNumber of endpoint table. If it is not associated with any endpoint, then it is set to -1. It s… |
| 1.3.6.1.4.1.351.110.4.7.1.1.8 | Columnds0IfType | read-only | current | This object indicates the interface type associated with the ds0. bearer(81) : ds0 ifType is considered as bearer if the DS0 is used for carrying voice traffic… |
| 1.3.6.1.4.1.351.110.4.7.1.1.9 | Columnds0CasVariantName | read-write | current | This object indicates the index to the CAS variant table. This parameter can be configured after configuring this ds0 as an endpoint. This object cannot be mod… |
| 1.3.6.1.4.1.351.110.4.7.1.1.10 | Columnds0CasCadenceOnTime | read-write | current | This attribute describes the duration during which the digit tone is generated. This object is applicable only for CAS backhaul applications. For trunking appl… |
| 1.3.6.1.4.1.351.110.4.7.1.1.11 | Columnds0CasCadenceOffTime | read-write | current | This attribute corresponds to the silence between the digit tones. This object is applicable only for CAS backhaul applications. For trunking application it is… |
| 1.3.6.1.4.1.351.110.4.7.1.1.12 | Columnds0InsertLocalCas | read-write | current | This object tells the framer whether to force the cas bits to a value defined by ds0LocalCasPattern or not. If this is enabled the framer will force the cas (A… |
| 1.3.6.1.4.1.351.110.4.7.1.1.13 | Columnds0LocalCasPattern | read-write | current | This object contains the pattern that the cas (ABCD) bits will have when ds0InsertLocalCas is enabled. |
| 1.3.6.1.4.1.351.110.4.7.1.1.14 | Columnds0LoopbackCommand | read-write | current | This object represents the loopback type at the ds0 level.The ds0 configuration overrides the line level configuration. NoLoop There is no loopback on this ds0… |
| 1.3.6.1.4.1.351.110.4.7.1.1.15 | Columnds0CasParameterSource | read-write | current | This object indicates VISM whether to read the cas related timer parameters from the casAppl file downloaded for that endpoint or to read from this mib. This g… |
| 1.3.6.1.4.1.351.110.4.7.1.1.16 | Columnds0CasOnHookMinMakeTime | read-write | current | This indicates the the minimum time in msecs for which the on hook pattern should be present in order for it to be recognised else the signal will be considere… |
| 1.3.6.1.4.1.351.110.4.7.1.1.17 | Columnds0CasOffHookMinMakeTime | read-write | current | This indicates the minimum time in msecs for which the off hook pattern should be present in order for it to be recognised else the signal will be considered t… |
| 1.3.6.1.4.1.351.110.4.7.1.1.18 | Columnds0CasWinkMinMakeTime | read-write | current | The wink consists of off-hook A-B bit pattern, followed by on-hook A-B bit pattern in timed sequence. This object indicates the minimum duration for which the … |
| 1.3.6.1.4.1.351.110.4.7.1.1.19 | Columnds0CasWinkMaxMakeTime | read-write | current | The wink consists of off-hook A-B bit pattern, followed by on-hook A-B bit pattern in timed sequence. This object indicates the maximum duration for which the … |
| 1.3.6.1.4.1.351.110.4.7.1.1.20 | Columnds0CasWinkBreakTime | read-write | current | The wink consists of off-hook A-B bit pattern, followed by on-hook A-B bit pattern in timed sequence. This object indicates the minimum duration for which the … |
| 1.3.6.1.4.1.351.110.4.7.1.1.21 | Columnds0CasGlareTime | read-write | current | When the terminating gateway receives off Hook event from the Call Agent it starts the timer specified in this object to see if the terminating side is also tr… |
| 1.3.6.1.4.1.351.110.4.7.1.1.22 | Columnds0CasGaurdTime | read-write | current | The gaurd time is the duration between the end of one call and the start of next call. This object specifies what should be such a duration. All state changes … |
| 1.3.6.1.4.1.351.110.4.7.1.1.23 | Columnds0CasDelayImmedStart | read-write | current | This timer indicates the time that VISM should wait before outpulsing digits to the PBX after sending an off hook event. This applies only to immediate start p… |
| 1.3.6.1.4.1.351.110.4.7.1.1.24 | Columnds0SignalingType | read-only | current | This attribute indicates the type of signaling on the line to which this ds0 belongs. CAS - Channel Associated Signaling CCS - Common Channel Signaling none - … |
| 1.3.6.1.4.1.351.110.4.7.1.1.25 | Columnds0CasMinDelayDialTime | read-write | current | This is an object for an E & M signaling protocol like wink-start for this ds0. The difference is that the address-control signal is different from wink. The o… |
| 1.3.6.1.4.1.351.110.4.7.1.1.26 | Columnds0CasMinStartDialTime | read-write | current | This is an object for an E & M signaling protocol like wink-start for this ds0. The difference is that the address-control signal is different from wink. The o… |
| 1.3.6.1.4.1.351.110.4.7.1.1.27 | Columnds0CasFlashMinMakeTime | read-write | current | Flash is a CAS signal generated by users to request special services. The interpretation of the flash depends on the protocol in use. The signal itself is an o… |
| 1.3.6.1.4.1.351.110.4.7.1.1.28 | Columnds0CasFlashMaxMakeTime | read-write | current | Flash is a CAS signal generated by users to request special services. The interpretation of the flash depends on the protocol in use. The signal itself is an o… |
| 1.3.6.1.4.1.351.110.4.7.1.1.29 | Columnds0CasDirectionality | read-write | current | This object specifies the direction in which CAS calls will be accepted on this endpoint. If this object is set to bidirectional(1): VISM can send and receive … |
| 1.3.6.1.4.1.351.110.4.7.1.1.30 | Columnds0CasGlarePolicy | read-write | current | This object specifies how a bidirectional endpoint should resolve glare. This object will be used only if dsx0VismDirectionality of the endpoint is 'bidirectio… |
| 1.3.6.1.4.1.351.110.4.7.1.1.31 | Columnds0CasIncomingMgcpPackage | read-write | current | This object, in conjunction with the card level persistentXgcpEventsTable, controls how persistent CAS events (like seize, disconnect, etc) related to an incom… |
| 1.3.6.1.4.1.351.110.4.7.1.1.32 | Columnds0CasOutgoingMgcpPackage | read-write | current | This object, in conjunction with the card level persistentXgcpEventsTable, controls how persistent CAS events (like answer, disconnect, etc) related to an outg… |
| 1.3.6.1.4.1.351.110.4.7.1.1.33 | Columnds0InputGain | read-write | current | This object indicates the amount of gain inserted at the receiver side of a ds0 channel, in dB (decibel) units. The default value of this object is 0 dB. The i… |
| 1.3.6.1.4.1.351.110.4.7.1.1.34 | Columnds0OutputAttenuation | read-write | current | This object contains the amount of attenuation inserted at the transmit side of a ds0 channel, in dB (decibel) units. The output attenuation settings only defi… |
| 1.3.6.1.4.1.351.110.4.7.1.1.35 | Columnds0MusicThreshold | read-write | current | The indicates Music On Hold Threshold in dBm. Based on this value, VISM DSP will interprete the incoming signal from TDM side as either silence or voice, and c… |
| 1.3.6.1.4.1.351.110.4.7.1.1.36 | Columnds0SidPacket | read-write | current | This object specifies whether the Silence Indication Detection (SID) packet should be generated when silence suppression is in active mode. The SID packet indi… |
| 1.3.6.1.4.1.351.110.4.7.1.1.37 | Columnds0ExecDiag | read-write | current | This object indicates the status of DSP channel level RAS on the VISM. When it is enable VISM will configure the DSP through HOST-DSP message on the individual… |
| 1.3.6.1.4.1.351.110.4.7.1.1.38 | Columnds0Companding | read-write | current | This object indicates whether input from / output to the TDM side of DS0 is u-law or a-law stream. The setting of this object will not take effect unless the c… |
| 1.3.6.1.4.1.351.110.4.7.1.1.39 | Columnds0RxCasTransTblName | read-write | current | This object identifies the template name 'cvcmCasTemplateName' in the CISCO-VOICE-CAS-MODULE-MIB associated with the receive signaling channel on a DS0. |
| 1.3.6.1.4.1.351.110.4.7.1.1.40 | Columnds0TxCasTransTblName | read-write | current | This object identifies the template name 'cvcmCasTemplateName' in the CISCO-VOICE-CAS-MODULE-MIB associated with the transmit signaling channel on a DS0. |
| 1.3.6.1.4.1.351.110.4.7.1.1.41 | Columnds0TxRxCasConfig | read-write | current | This object indicates configuration on a DS0. 'transmit'- Configure transmit signaling channel on the DSP with user defined CAS pattern to translate incoming A… |
| 1.3.6.1.4.1.351.110.4.7.2 | Tabledsx0VismChanMapTable | not-accessible | current | This table is created implicitly at the time of creating and deleting the endpoints. This table provides the mapping information from a line and channel to obt… |
| 1.3.6.1.4.1.351.110.4.7.2.1 | Rowdsx0VismChanMapEntry | not-accessible | current | Each entry represents the mapping from dsx1Line number to ds0 channel Number and provides the ifIndex mapping. |
| 1.3.6.1.4.1.351.110.4.7.2.1.1 | Columndsx1LineNum | read-only | current | This object describes the physical line number on VISM card. |
| 1.3.6.1.4.1.351.110.4.7.2.1.2 | Columnds0ChanNum | read-only | current | This object describes the ds0 number or channel number within a T1 or E1 line. The valid channel numbers are 1 to 24 for T1 line and 1 - 31 for E1 line. |
| 1.3.6.1.4.1.351.110.4.7.2.1.3 | Columnds0ChanMapIfIndex | read-only | current | This object describes the ifIndex derived based on the line number and the channel number within the line according to the formula: IfIndex = 31 * (Ds1# - 1) +… |
| 1.3.6.1.4.1.351.110.4.7.3 | TablevismDs0LineStatsTable | not-accessible | current | This table contains information on DS0s configured on DS1 interface. |
| 1.3.6.1.4.1.351.110.4.7.3.1 | RowvismDs0LineStatsEntry | not-accessible | current | An entry in the vismDs0LineStatsTable. Each entry contains following information applicable for each DS1 interface: Total DS0s Free DS0s Active DS0s Blocked DS… |
| 1.3.6.1.4.1.351.110.4.7.3.1.1 | Columnds0LineNum | read-only | current | This object is the identifier of a DS1/E1 Interface on a managed device. The number of entries is 8 in a VISM and VISM-PR card. |
| 1.3.6.1.4.1.351.110.4.7.3.1.2 | ColumnlineTotalDs0Count | read-only | current | This is the total number of ds0s configured on this DS1 line. |
| 1.3.6.1.4.1.351.110.4.7.3.1.3 | ColumnlineFreeDs0Count | read-only | current | This is the total number of free ds0s on this DS1 line. |
| 1.3.6.1.4.1.351.110.4.7.3.1.4 | ColumnlineActiveDs0Count | read-only | current | This is the number of active ds0s on this line. |
| 1.3.6.1.4.1.351.110.4.7.3.1.5 | ColumnlineBlockDs0Count | read-only | current | This is the number of blocked ds0s on this line. |
| 1.3.6.1.4.1.351.110.4.7.3.1.6 | ColumnlineActiveHighWaterMark | read-only | current | This is the high water mark number of ds0s that were active simultaneously on the line. |
| 1.3.6.1.4.1.351.110.4.7.3.1.7 | ColumnlineStatsClrButton | read-write | current | This variable is used to clear the vism Ds0 line status entry. 1 = No action, 2 = Clear alarm. |
| 1.3.6.1.4.1.351.110.4.7.4 | TablevismDs0StatusTable | not-accessible | current | This table contains ds0 status information on a DS1 interface. |
| 1.3.6.1.4.1.351.110.4.7.4.1 | RowvismDs0StatusEntry | not-accessible | current | An entry in the Ds0 Status Table. |
| 1.3.6.1.4.1.351.110.4.7.4.1.1 | Columnds0LineNumber | read-only | current | This object is the identifier of a DS1/E1 Interface on a managed device. The number of entries is 8 in a VISM and VISM-PR card. |
| 1.3.6.1.4.1.351.110.4.7.4.1.2 | Columnds0Number | read-only | current | This object identifies the ds0 number on a DS1 interface. |
| 1.3.6.1.4.1.351.110.4.7.4.1.3 | Columnds0Status | read-only | current | This object is the status of the ds0. idle - This ds0 is in idle state. busy - This ds0 is in busy state. Ds0 enters this state when it is in the process of be… |
| 1.3.6.1.4.1.351.110.4.7.4.1.4 | Columnds0StatusClrButton | read-write | current | This variable is used to clear the vism Ds0 status. 1 = No action, 2 = Clear alarm |
| 1.3.6.1.4.1.351.150.81 | IdentityciscoVismDsx0MIB | This MIB module contains ds0 configuration, Status and DS0 related information on a DS1 interface supported in VISM module. VISM is a Voice Interworking Servic… | ||
| 1.3.6.1.4.1.351.150.81.2 | NodeciscoVismDsx0MIBConformance | |||
| 1.3.6.1.4.1.351.150.81.2.1 | NodeciscoVismDsx0MIBGroups | |||
| 1.3.6.1.4.1.351.150.81.2.1.1 | GroupciscoVismCardStatsGroup | current | The collection of objects used for DS0 Statistics applicable to VISM Module. | |
| 1.3.6.1.4.1.351.150.81.2.1.2 | GroupciscoVismDsx0LineStatsGroup | current | The collection of objects used for DS0 Line statistics. | |
| 1.3.6.1.4.1.351.150.81.2.1.3 | GroupciscoVismDsx0StatusGroup | current | The collection of objects used for DS0 status. | |
| 1.3.6.1.4.1.351.150.81.2.1.4 | GroupciscoVismDsx0ConfGroup | deprecated | The collection of objects used for DS0 configuration in VISM module. | |
| 1.3.6.1.4.1.351.150.81.2.1.5 | GroupciscoVismDsx0ChanMapGroup | current | The collection of objects used for mapping DS0 to ifIndex. | |
| 1.3.6.1.4.1.351.150.81.2.1.6 | GroupciscoVismDsx0ConfDeprecatedGroup | deprecated | The collection of objects that were supported earlier but deprecated now. | |
| 1.3.6.1.4.1.351.150.81.2.1.7 | GroupciscoVismDsx0ConfGroup2 | current | The collection of objects used for DS0 configuration in VISM module. | |
| 1.3.6.1.4.1.351.150.81.2.2 | NodeciscoVismDsx0MIBCompliances | |||
| 1.3.6.1.4.1.351.150.81.2.2.1 | ComplianceciscoVismDsx0Compliance | deprecated | The compliance statement for objects related to DS0 mib objects. | |
| 1.3.6.1.4.1.351.150.81.2.2.2 | ComplianceciscoVismDsx0Compliance2 | current | The compliance statement for objects related to DS0 mib objects. |