CISCO-VISM-MODULE-MIB
139 objects
This MIB module contains VISM Card specific attributes and call statistics information for VISM service module.
Imported Objects
| BASIS-MIB | cardSpecific voice |
| CISCOWAN-SMI | ciscoWan |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 IpAddress MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.351.110.3.17 | NodevismConfig | |||
| 1.3.6.1.4.1.351.110.3.17.1 | NodevismIpGrp | |||
| 1.3.6.1.4.1.351.110.3.17.1.1 | ScalarvismIpAddress | read-write | current | This object identifies the IP address of VISM card. Each VISM card has its own IP address. IP address for each VISM card is required to communicate with the ca… |
| 1.3.6.1.4.1.351.110.3.17.1.2 | ScalarvismSubNetMask | read-write | current | SUB-NETMASK of the VISM IP interface. This object is applicable if the object vismMode is in VoIP or Switched mode. |
| 1.3.6.1.4.1.351.110.3.17.1.3 | ScalarvismControlTos | read-write | current | This object is used to provision the bitmask used for the TOS (Type Of Service) octet for cells carrying the control xGCP(Gateway Control Protocol) traffic. De… |
| 1.3.6.1.4.1.351.110.3.17.1.4 | ScalarvismBearerIpAddress | read-write | current | The bearer IP address of VISM card. This is an optional second IP address of the VISM card. If this bearer IP address is defined, the vismIpAddress automatical… |
| 1.3.6.1.4.1.351.110.3.17.1.5 | ScalarvismBearerSubNetMask | read-write | current | Bearer SUB-NETMASK of the VISM IP interface. This optional bearer subnet mask must be provided when vismBearerIpAddress is provided. |
| 1.3.6.1.4.1.351.110.3.17.2 | NodevismVoIpGrp | |||
| 1.3.6.1.4.1.351.110.3.17.2.1 | ScalarvismBearerTos | read-write | current | This object is used to provision the bitmask used for the TOS octet for cells carrying VoIP bearer RTP(Real-time Transport Protocol) traffic. Default value 160… |
| 1.3.6.1.4.1.351.110.3.17.2.2 | ScalarvismRtcpRepInterval | read-write | current | This attribute defines the RTCP(Real-time Transport Control Protocol) report interval (defined in RFC 1889). This indicates the interval at which the RTCP repo… |
| 1.3.6.1.4.1.351.110.3.17.2.3 | ScalarvismRtpReceiveTimer | read-write | current | This object defines whether the RTP packets receive timer on the VISM needs to be enabled or not. For some VoIP applications if a connection is in send-recv mo… |
| 1.3.6.1.4.1.351.110.3.17.2.4 | ScalarvismPacketizationPeriod | read-only | deprecated | This object is used to provision the packetization period to be applied and is applicable for VoIP only. For VoAAL2 adaptations, the packetization period is de… |
| 1.3.6.1.4.1.351.110.3.17.2.5 | ScalarvismVoIpDtmfRelay | read-write | current | This attribute defines whether the DTMF (Dual Tone Multi-Frequency) digits need to be transported to the other endpoint via NSE(Named Signal Event) packets. |
| 1.3.6.1.4.1.351.110.3.17.2.6 | ScalarvismVoIpCasTransport | read-write | current | This attribute defines whether the CAS(Channel Associated Signaling) bits need to be transported to the other endpoint via NSE packets. |
| 1.3.6.1.4.1.351.110.3.17.2.7 | ScalarvismVoIpTripleRedundancy | read-write | current | This attribute defines whether triple redundancy is enabled or not. With triple redundancy, NSEs are sent three times at 20 ms intervals. For reliable channels… |
| 1.3.6.1.4.1.351.110.3.17.2.8 | ScalarvismVoIpVADTimer | read-write | current | This attribute defines the hangover time for VAD(Voice Activity Detection) in milliseconds. Once the voice inactivity is detected, the gateway will wait for th… |
| 1.3.6.1.4.1.351.110.3.17.2.9 | ScalarvismVoIpNTECapabilityNegotiate | read-write | current | This attribute defines whether the VISM has the capability to negotiate the list of events either NSE or NTE(Named Telephony Events), using rtpmap and fmtpmap … |
| 1.3.6.1.4.1.351.110.3.17.2.10 | ScalarvismVoIpSIDPayloadType | read-write | current | This attribute sets the payload type of a RTP packet carrying SID(Silence Insertion Descriptor) which is sent to the other end when silence is detected. The de… |
| 1.3.6.1.4.1.351.110.3.17.2.11 | ScalarvismVoIpDPvcOamCellGap | read-write | current | This attribute defines the inter cell gap for dual PVC(Permanent Virtual Circuit) OAM (Operational and management) cells. |
| 1.3.6.1.4.1.351.110.3.17.2.12 | ScalarvismVoIpDPvcRetryCnt | read-write | current | This attribute defines the threshold for failure of a PVC. If the number of consecutive OAM cells sent for which no ack was received equals this number then th… |
| 1.3.6.1.4.1.351.110.3.17.2.13 | ScalarvismVoIpDPvcRecoverCnt | read-write | current | This attribute defines the threshold for recovery of a PVC. If the number of consecutive OAM cells sent for which ack was received equals this number then the … |
| 1.3.6.1.4.1.351.110.3.17.2.14 | ScalarvismRtcpRecvMultiplier | read-write | current | The object vismRtcpRepInterval specified above defines an approximate RTCP report interval (defined in RFC 1889) which indicates the interval in milliseconds a… |
| 1.3.6.1.4.1.351.110.3.17.2.15 | ScalarvismVoIpLapdTrunkPVC | read-write | current | This object should be used for VoIP Trunking applications and only if the signaling type is configured to be CCS(Common Channel Signaling). By default the PRI(… |
| 1.3.6.1.4.1.351.110.3.17.2.16 | ScalarvismVoIpEventNegotiationPolicy | read-write | current | This attribute defines whether or not the VISM should advertise the event codecs, NSE, NTE, or Cisco-rtp, in addition to the list of events specified by the ca… |
| 1.3.6.1.4.1.351.110.3.17.3 | NodevismDspGrp | |||
| 1.3.6.1.4.1.351.110.3.17.3.1 | ScalarvismEcanCnfIdlePattern | read-only | deprecated | Echo Canceller pattern for Idle code. Mu-Law : 1 - 7f, 2 - ff, 3 - 7f or ff, 4 - f7 A-Law : 1 - None, 2 - 54, 3 - 55, 4 - Programmable Idle code. DEFVAL : 'pat… |
| 1.3.6.1.4.1.351.110.3.17.3.2 | ScalarvismEcanCnfIdleDirection | read-only | deprecated | Echo Canceller Idle Direction. This determines in which direction the Idle code must be present. |
| 1.3.6.1.4.1.351.110.3.17.3.3 | ScalarvismCompCnfPacketSize | read-write | current | Compressed output packet size - This value is used in the DSP(Digital Signal Processing) interface API commands to configure the DSPs for the maximum packet si… |
| 1.3.6.1.4.1.351.110.3.17.3.4 | ScalarvismERL | read-write | current | This object is used to provision the return echo lost, i.e the db loss of the echo that the DSPs are supposed to cancel. |
| 1.3.6.1.4.1.351.110.3.17.3.5 | ScalarvismJitterDelayMode | read-write | deprecated | This object is used to provision the jitter buffer mode to be apply to a call connection. The possible values are: 'fixed' : means use a constant jitter buffer… |
| 1.3.6.1.4.1.351.110.3.17.3.6 | ScalarvismJitterInitialDelay | read-write | deprecated | Defines the jitter buffer size. If the vismJitterDelayMode is set to be fixed, the jitter buffer is fixed at this value for the call. If vismJitterDelayMode is… |
| 1.3.6.1.4.1.351.110.3.17.3.7 | ScalarvismAdaptiveGainControl | read-write | current | If set to 'on', the DSP will adjust the gain of the call connection to an optimal value. |
| 1.3.6.1.4.1.351.110.3.17.3.8 | ScalarvismDspHealth | read-only | current | This attribute indicates the health of the DSPs. It is a percentage of the total number of DSPs that are currently functional. |
| 1.3.6.1.4.1.351.110.3.17.3.9 | ScalarvismUpspeedCodec | read-write | current | This object specifies the codec to be used when fax upspeed happens. The default value for this object is 'g711u' when the line type is T1 and 'g711a' when the… |
| 1.3.6.1.4.1.351.110.3.17.3.10 | ScalarvismPayloadType | read-write | current | This object specifies the payload type to be used when fax upspeed happens. IANA values (0..95) are static payload and (96..127) are dynamic payload type. This… |
| 1.3.6.1.4.1.351.110.3.17.3.11 | ScalarvismDSPHeartbeat | read-write | current | This object will specify the timer interval, DSP send a regular heartbeat messages from the DSP to the HOST Application. If the value is zero the Heartbeat mes… |
| 1.3.6.1.4.1.351.110.3.17.3.12 | ScalarvismFaxDeJitterMode | read-write | current | This object specifies the de-jitter mode to be used for the fax upspeed. This object is applicable only in the case of VoIP applications. |
| 1.3.6.1.4.1.351.110.3.17.3.13 | ScalarvismFaxDeJitterInitialDelay | read-write | current | This object defines the de-jitter buffer size for fax upspeed. If the vismFaxDeJitter Mode is set to be 'fixedWithTS' or 'fixedWithoutTS', the jitter buffer si… |
| 1.3.6.1.4.1.351.110.3.17.4 | NodevismSystemGrp | |||
| 1.3.6.1.4.1.351.110.3.17.4.1 | ScalarvismDaughterCardSerialNum | read-only | current | A unique value for each VISM daughter card, entered in nvram by manufacturing. The serial number is on the non-volatile RAM on the VISM daughter card. |
| 1.3.6.1.4.1.351.110.3.17.4.2 | ScalarvismDaughterCardDescription | read-only | current | This object identifies the VISM daughter card. |
| 1.3.6.1.4.1.351.110.3.17.4.3 | ScalarvismDaughterCardHWRev | read-only | current | This object identifies the hardware revision number for the daughter card. |
| 1.3.6.1.4.1.351.110.3.17.4.4 | ScalarvismEcanEncoding | read-only | current | The object identifies the voice encoding type, mu-law or a-law. 'mu-law' is returned for T1 lines and 'a-law' is returned for E1 lines. |
| 1.3.6.1.4.1.351.110.3.17.4.5 | ScalarvismMode | read-only | current | This attribute defines the connection model that the VISM card is configured to operate with. This object can be modified by CLI(Command Line Interface) only. … |
| 1.3.6.1.4.1.351.110.3.17.4.6 | ScalarvismPrevMode | read-only | deprecated | This attribute indicates the mode in which VISM was operating before the object vismMode value was changed. i.e It gives the value of vismMode before it got ch… |
| 1.3.6.1.4.1.351.110.3.17.4.7 | ScalarvismCacEnable | read-write | current | This attribute describes whether CAC (Connection Admission Control) functionality needs to be applied on the VISM card, on a per PVC basis. For some applicatio… |
| 1.3.6.1.4.1.351.110.3.17.4.8 | ScalarvismAvailableDs0Count | read-only | current | This attribute describes the number of DS0s available for new connections on VISM. This is modified by the VISM firmware after each connection is setup. |
| 1.3.6.1.4.1.351.110.3.17.4.9 | ScalarvismAppliedTemplate | read-only | current | This attribute describes the Codec template currently configured on the VISM card. The value refers to an index to the vismCodecTemplateCnfGrpTable (defined in… |
| 1.3.6.1.4.1.351.110.3.17.4.11 | ScalarvismTftpServerDn | read-write | current | This object holds the domain name of the tftp server from where the CAS module will download the CAS files. This domain name can be resolved internally or exte… |
| 1.3.6.1.4.1.351.110.3.17.4.12 | ScalarvismXgcpBearerNetworkType | read-write | current | This object specifies the network type to use in order to transport bearer traffic. The user can configure this to IP or ATM based on where the VISM will be lo… |
| 1.3.6.1.4.1.351.110.3.17.4.13 | ScalarvismXgcpBearerVCType | read-write | current | This object specifies the VC(Virtual Channel) type to use in order to transport bearer traffic. If the call agent specifies the VC type in the MGCP local conne… |
| 1.3.6.1.4.1.351.110.3.17.4.14 | ScalarvismXgcpBearerConnectionType | read-write | current | This object specifies the connection type used to transport bearer traffic. If the vismXgcpBearerNetworkType is chosen to be IP then the value of this object h… |
| 1.3.6.1.4.1.351.110.3.17.4.15 | ScalarvismBearerContinuityTimer | read-write | current | This object specifies the co4 (bearer continuity) timer in millisecs. The timer will be started in the terminating/originating gateway for a duration as specif… |
| 1.3.6.1.4.1.351.110.3.17.4.16 | ScalarvismCodecNegotiationOption | read-write | current | This object helps in forming an ordered intersection of lists and one of the lists must be used in determining the resulting order of codecs. Lco - local conne… |
| 1.3.6.1.4.1.351.110.3.17.4.17 | ScalarvismProfileNegotiationOption | read-write | current | This object helps in forming an ordered intersection of lists and one of the lists must be used in determining the resulting order of profiles. Lco - local con… |
| 1.3.6.1.4.1.351.110.3.17.4.18 | ScalarvismCarrierLossPolicy | read-write | current | This object defines the policy that needs to be applied when a carrier loss is detected. This states whether to switch to the pre-upspeed codec or to remain wi… |
| 1.3.6.1.4.1.351.110.3.17.4.19 | ScalarvismCacRejectionPolicy | read-write | current | This attribute defines the policy that needs to be applied once the CAC function rejects the upspeeding of a connection, due to a fax/modem switch-over request… |
| 1.3.6.1.4.1.351.110.3.17.4.20 | ScalarvismExtDnsServerDn | read-write | current | This object refers to the domain name of the external DNS server which will be used to resolve other domain name. Currently this domain name can only be resolv… |
| 1.3.6.1.4.1.351.110.3.17.4.21 | ScalarvismFeatureBitMap | read-write | current | This object denotes the bit map for VISM features. It indicates the current features that are enabled. It should be consistent with vismMode. When user change … |
| 1.3.6.1.4.1.351.110.3.17.4.22 | ScalarvismVADTolerance | read-write | current | The value in this object refers to the customer accepted drop rate for voice connections when the bandwidth usage exceeds allowed value. The actual range of th… |
| 1.3.6.1.4.1.351.110.3.17.4.23 | ScalarvismVADDutyCycle | read-write | current | This object refers to the talk-spurts duty cycle. The unit is in percentage. When the value of this object is to be passed to underlying CAC module in VISM thi… |
| 1.3.6.1.4.1.351.110.3.17.4.24 | ScalarvismAggregateTrafficClipping | read-write | current | This attribute defines the aggregate traffic clipping policy which is applicable to all bearer traffic generated at VISM card. The applicable options are: 'dis… |
| 1.3.6.1.4.1.351.110.3.17.4.25 | ScalarvismAggregateSvcBandwidth | read-write | current | The aggregate svc bandwidth is used for AAL2 SVC aggregate SVC CAC and also used for aggregate traffic clipping at VISM card when vismAggregateTrafficClipping … |
| 1.3.6.1.4.1.351.110.3.17.4.26 | ScalarvismBearerContinuityTest | read-write | current | This attribute defines whether the bearer continuity test for a connection will be performed at the time of call setup or not. When the vismBearerContinuityTes… |
| 1.3.6.1.4.1.351.110.3.17.4.27 | ScalarvismCaleaEnable | read-write | current | This attribute describes whether CALEA (Communication Assistance for Law Enforcement Agency) functionality needs to be enabled on the VISM card. This attribute… |
| 1.3.6.1.4.1.351.110.3.17.4.28 | ScalarvismMaxConfNum | read-write | current | Identify how many conference will be supported on a VISM card |
| 1.3.6.1.4.1.351.110.3.17.4.29 | ScalarvismLongDurationTimer | read-write | current | The long duration is the elapse time in hour to indicate a connection has been established for a given period of time. The default time is one hour. |
| 1.3.6.1.4.1.351.110.3.17.4.30 | ScalarvismContinuityCo1Timer | read-write | current | A 2010Hz tone is applied, if the co1(Continuity Tone 1) is specify as a signal the range is 2010Hz +/- 8Hz and if it is specify as an event the range is 2010Hz… |
| 1.3.6.1.4.1.351.110.3.17.4.31 | ScalarvismContinuityCo2Timer | read-write | current | A 1780Hz tone is applied, if the co2(Continuity Tone 2) is specify as a signal the range is 1780Hz +/- 20Hz and if it is specify as an event the range is 1780H… |
| 1.3.6.1.4.1.351.110.3.17.4.32 | ScalarvismReverseCotTone | read-write | current | This attribute defines the direction of COT Tone that is sent in a 2w to 4w arrangement. The VISM responds to a request from the call agent through the M:contt… |
| 1.3.6.1.4.1.351.110.3.17.4.33 | ScalarvismSendDnEnable | read-write | current | This will allow VISM to send domain name as part of Audit Enpoint response to the call agent when it is configured as 'true(1)'. |
| 1.3.6.1.4.1.351.110.3.17.4.34 | ScalarvismSendDataGramSize | read-write | current | Specify the size of datagram that should be sent when the vismSendDnEnable is set to 'true(1)'. Any value greater than the specified size will be rejected. |
| 1.3.6.1.4.1.351.110.3.17.4.35 | ScalarvismOamLoopThreshold | read-write | current | Specify OAM loopback cell loss count before declaring a PVC alarm. |
| 1.3.6.1.4.1.351.110.3.17.4.36 | ScalarvismFreeDs0Threshold | read-write | current | This attribute holds the threshold value of free DS0 counts on the VISM card. A trap is sent out if the number of free ds0s fall below this threshold. |
| 1.3.6.1.4.1.351.110.3.17.4.37 | ScalarvismCPUUtilizationThreshold | read-write | current | This attribute holds the threshold value of CPU utilization on the VISM card. A trap is sent out if the CPU utilization equals or exceeds this threshold. |
| 1.3.6.1.4.1.351.110.3.17.4.38 | ScalarvismMemoryUtilizationThreshold | read-write | current | This attribute holds the threshold value of memory utilization on the VISM card. A trap is sent out if the memory utilization equals or exceeds this threshold. |
| 1.3.6.1.4.1.351.110.3.17.4.39 | ScalarvismDualToneDetect | read-write | current | This object is use to enable/disable dual tone configuration. When the dual tone is enable and detected, the Marconi Application will upspeed to VBD(Voice Band… |
| 1.3.6.1.4.1.351.110.3.17.4.40 | ScalarvismAisSuppression | read-write | deprecated | This object is used to enable/disable the AIS(Alarm Indication Signal) suppression functionality. When AIS suppression is enabled AIS and RDI(Remote Defect Ind… |
| 1.3.6.1.4.1.351.110.3.17.4.41 | ScalarvismBearerIpPingEnable | read-write | current | This object is used to enable/disable the bearer IP ping response configuration. When set to true, the bearer IP ping feature will be enabled on the module and… |
| 1.3.6.1.4.1.351.110.3.17.4.42 | ScalarvismTrapFilteringEnable | read-write | current | This object is used to enable/disable the trap filtering feature on the module. When set to true, the trap filtering feature is enabled on the module. When set… |
| 1.3.6.1.4.1.351.110.3.17.4.43 | ScalarvismSplModemToneBitMap | read-write | current | This bit map is applicable for any special modem tones that need to be enabled or disabled on the module. If a bit is set to 1, the tone detection is enabled. … |
| 1.3.6.1.4.1.351.110.3.17.4.44 | ScalarvismSSRCEnable | read-write | current | This object is used to enable/disable more than one SSRC (Synchronization Source) per RTP session. When set to true, the module will accept more than one SSRC … |
| 1.3.6.1.4.1.351.110.3.17.4.45 | ScalarvismOamLoopbackSetCLP | read-write | current | This object is used to set the cell loss priority of the oam loopback cell for all the PVCs. If set to true, all the CLP bits will be set to 1. If set to false… |
| 1.3.6.1.4.1.351.110.3.17.4.46 | ScalarvismPvcAlarmLogEnable | read-write | current | This object specifies whether detailed alarm logging on all the PVC's on the module is enabled or disabled. If this object is true, detailed alarm logging for … |
| 1.3.6.1.4.1.351.110.3.17.4.47 | ScalarvismPvcAlarmLogAdminTimer | read-write | current | This object specifies the time for which the detailed alarm logging for all the PVCs on the module will remain active. The value in this object can be set and … |
| 1.3.6.1.4.1.351.110.3.17.4.48 | ScalarvismPvcAlarmLogOperTimer | read-only | current | This object specifies the time remaining in minutes for which the detailed alarm logging will remain enabled on all the PVCs on the module. When this value bec… |
| 1.3.6.1.4.1.351.110.3.17.4.49 | ScalarvismContinuityCheckCellEnable | read-write | current | This object is used to enable/disable the continuity check cell for all the PVCs on the module. If set to true, the module will transmit continuity check cells… |
| 1.3.6.1.4.1.351.110.3.17.5 | NodevismTrapObjGrp | |||
| 1.3.6.1.4.1.351.110.3.17.5.1 | ScalarvismConfigChangeTypeBitMap | read-only | current | Configuration change Type BitMap used in vismTableChanged trap and vismScalarChanged trap. When used in vismTableChanged trap, the bits indicate the following:… |
| 1.3.6.1.4.1.351.110.3.17.5.2 | ScalarvismTrapIntIndex1 | read-only | current | This object is used only for the purpose of sending it in the trap varbind. This object is used for two purposes: 1. When the integer index of a SMIv2 table ha… |
| 1.3.6.1.4.1.351.110.3.17.5.3 | ScalarvismTrapIntIndex2 | read-only | current | This object is used only for the purpose of sending it in the trap varbind. This object is used for two purposes: 1. This object will be used when the SMIv2 ta… |
| 1.3.6.1.4.1.351.110.3.17.5.4 | ScalarvismTrapStrIndex1 | read-only | current | This object is used only for the purpose of sending it in the trap varbind. This object is used for two purposes: 1. When the OctetString index of a SMIv2 tabl… |
| 1.3.6.1.4.1.351.110.3.17.5.5 | ScalarvismTrapIntegerValue | accessible-for-notify | current | This object is used only for the purpose of sending it in the trap varbind. This object can be used when the instance value of an integer object has to be sent… |
| 1.3.6.1.4.1.351.110.3.17.6 | NodevismAal2Grp | |||
| 1.3.6.1.4.1.351.110.3.17.6.1 | ScalarvismAal2SubcellMuxing | read-write | current | This object is a card level parameter for AAL2 adaptation and it identifies the mutiplexing function of the AAL2 CPS(Common Part Sub-layer). When it is disable… |
| 1.3.6.1.4.1.351.110.3.17.6.2 | ScalarvismAal2DtmfRelay | read-write | current | This attribute defines whether the DTMF(Dual Tone Multi Frequency) digits need to be transported to the other end-point or not. The value in this object will b… |
| 1.3.6.1.4.1.351.110.3.17.6.3 | ScalarvismAal2CasTransport | read-write | current | This attribute defines whether the CAS bits need to be transported to the other endpoint. In the case of switching application, the CAS bits are backhauled to … |
| 1.3.6.1.4.1.351.110.3.17.6.4 | ScalarvismAal2Type3Redundancy | read-write | current | This attribute defines whether the triple redundancy is supported for Type 3 packets in AAL2 SVC/PVC. When Triple redundancy is enabled, the Type 3 packets (CA… |
| 1.3.6.1.4.1.351.110.3.17.6.5 | ScalarvismAal2VADTimer | read-write | current | This attribute defines the hangover time for VAD in milliseconds. Once the voice inactivity is detected, the gateway will wait for this duration before activat… |
| 1.3.6.1.4.1.351.110.3.17.6.6 | ScalarvismAal2CidFillTimer | read-write | current | This attribute defines the time (millisecs) to wait for filling up the cell when the next packet is not ready. After waiting for the time configured in this ob… |
| 1.3.6.1.4.1.351.110.3.17.7 | NodevismInteropGrp | |||
| 1.3.6.1.4.1.351.110.3.17.7.1 | ScalarvismXgcpSdpOst | read-write | current | This object is used to enable/disable building of s=,t=,o= lines in SDP(Session Description Protocol) message. If this object is set to 'enable' then it indica… |
| 1.3.6.1.4.1.351.110.3.17.7.2 | ScalarvismDynamicPT | read-write | current | This object is used to enable/disable dynamic payload type configuration on the VISM Card. |
| 1.3.6.1.4.1.351.110.3.25 | NodevismSystemPerfStats | |||
| 1.3.6.1.4.1.351.110.3.25.1 | ScalarvismCPUUtilization | read-only | current | This is the percentage of time CPU is in non-idle state. |
| 1.3.6.1.4.1.351.110.3.25.2 | ScalarvismMemoryUtilization | read-only | current | This is the percentage of memory in use by VISM. |
| 1.3.6.1.4.1.351.110.3.25.3 | ScalarvismSysPerfClrButton | read-write | current | This variable is used to clear all the CPU and Memory Utilization statistics. 'noaction(1)': The value return on a GET operation. 'clear(2)' : Clear alarm. |
| 1.3.6.1.4.1.351.110.5.5.13 | NodevismCallStats | |||
| 1.3.6.1.4.1.351.110.5.5.13.1 | ScalarvismTotalCalls | read-only | current | Total number of calls made in VISM. |
| 1.3.6.1.4.1.351.110.5.5.13.2 | ScalarvismSuccessfulCalls | read-only | current | Total number successful calls made in VISM. |
| 1.3.6.1.4.1.351.110.5.5.13.3 | ScalarvismFailedCalls | read-only | current | Total number failed calls made in VISM. |
| 1.3.6.1.4.1.351.110.5.5.13.4 | ScalarvismCallStatsClrButton | read-write | current | This variable is used to clear all the VISM call statistics. 'noaction': The value return on a GET operation 'clear': Clear all alarm |
| 1.3.6.1.4.1.351.150.82 | IdentityciscoVismModuleMIB | This MIB module contains VISM Card specific attributes and call statistics information for VISM service module. | ||
| 1.3.6.1.4.1.351.150.82.2 | NodeciscoVismModuleMIBConformance | |||
| 1.3.6.1.4.1.351.150.82.2.1 | NodeciscoVismModuleMIBGroups | |||
| 1.3.6.1.4.1.351.150.82.2.1.1 | GroupciscoVismPerfStatsGroup | current | The collection of objects which are used to represent VISM performance statistics. | |
| 1.3.6.1.4.1.351.150.82.2.1.2 | GroupciscoVismCallStatsGroup | current | The collection of objects which are used to represent VISM Call Statistics. | |
| 1.3.6.1.4.1.351.150.82.2.1.3 | GroupciscoVismIpGroup | current | This group contains objects that are specific to IP. | |
| 1.3.6.1.4.1.351.150.82.2.1.4 | GroupciscoVismVoIpGroup | current | This group contains objects that are specific to VoIP. | |
| 1.3.6.1.4.1.351.150.82.2.1.5 | GroupciscoVismDspGroup | current | This group contains objects that are used to manage DSPs on the VISM card. | |
| 1.3.6.1.4.1.351.150.82.2.1.6 | GroupciscoVismSystemGroup | deprecated | This group contains objects that are specific to the card. | |
| 1.3.6.1.4.1.351.150.82.2.1.7 | GroupciscoVismInteropGroup | current | This group contains objects which will enhance the interoperability functionalities of VISM. | |
| 1.3.6.1.4.1.351.150.82.2.1.8 | GroupciscoVismTrapObjGroup | current | This group contains objects that are defined for the purpose of sending in trap varbinds. | |
| 1.3.6.1.4.1.351.150.82.2.1.9 | GroupciscoVismAal2Group | current | This group contains objects which will enhance the interoperability functionalities of VISM. | |
| 1.3.6.1.4.1.351.150.82.2.1.10 | GroupciscoVismDspDeprecatedGroup | deprecated | The collection of objects that were supported earlier but deprecated now. | |
| 1.3.6.1.4.1.351.150.82.2.1.11 | GroupciscoVismSystemDeprecatedGroup | deprecated | The collection of objects that were supported earlier but deprecated now. | |
| 1.3.6.1.4.1.351.150.82.2.1.12 | GroupciscoVismVoIpDeprecateGroup | deprecated | The collection of objects that were supported earlier but deprecated now. | |
| 1.3.6.1.4.1.351.150.82.2.1.13 | GroupciscoVismSystemGroup1 | current | This group contains objects that are specific to the card. | |
| 1.3.6.1.4.1.351.150.82.2.1.14 | GroupciscoVismSystemFeatureGroup | deprecated | This group contains specific card level objects for feature support on the module. | |
| 1.3.6.1.4.1.351.150.82.2.1.15 | GroupciscoVismTrapVarbindGroup | current | This group contains objects that are defined for the purpose of sending in trap varbinds. | |
| 1.3.6.1.4.1.351.150.82.2.1.16 | GroupciscoVismSystemFeatureGroupRev1 | current | This group contains specific card level objects for feature support on the module. | |
| 1.3.6.1.4.1.351.150.82.2.1.17 | GroupciscoVismSystemGroupSup1 | current | This group contains objects that are specific to the card. | |
| 1.3.6.1.4.1.351.150.82.2.1.18 | GroupciscoVismDspGroupSup1 | current | This group contains objects that are used to manage DSPs on the VISM card. | |
| 1.3.6.1.4.1.351.150.82.2.2 | NodeciscoVismModuleMIBCompliances | |||
| 1.3.6.1.4.1.351.150.82.2.2.1 | ComplianceciscoVismModuleCompliance | deprecated | The compliance statement for objects related to VISM module. | |
| 1.3.6.1.4.1.351.150.82.2.2.2 | ComplianceciscoVismModuleCompliance1 | deprecated | The compliance statement for objects related to VISM module. | |
| 1.3.6.1.4.1.351.150.82.2.2.3 | ComplianceciscoVismModuleComplianceRev2 | deprecated | The compliance statement for objects related to VISM module. | |
| 1.3.6.1.4.1.351.150.82.2.2.4 | ComplianceciscoVismModuleComplianceRev3 | deprecated | The compliance statement for objects related to VISM module. | |
| 1.3.6.1.4.1.351.150.82.2.2.5 | ComplianceciscoVismModuleComplianceRev4 | current | The compliance statement for objects related to VISM module. |