CISCO-VOICE-ANALOG-IF-MIB
92 objects
Analog Voice Interface MIB module. This MIB manages the E&M, FXO, FXS Interfaces in the router.
Imported Objects
| CISCO-SMI | ciscoMgmt |
| IF-MIB | ifIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.62 | IdentityciscoVoiceAnalogIfMIB | Analog Voice Interface MIB module. This MIB manages the E&M, FXO, FXS Interfaces in the router. | ||
| 1.3.6.1.4.1.9.9.62.1 | NodecvaIfObjects | |||
| 1.3.6.1.4.1.9.9.62.1.1 | NodecvaIfGeneralObjects | |||
| 1.3.6.1.4.1.9.9.62.1.1.1 | TablecvaIfCfgTable | not-accessible | current | The Analog Voice Standard Configuration Table. It contains the standard configuration information of the analog telephony interface. |
| 1.3.6.1.4.1.9.9.62.1.1.1.1 | RowcvaIfCfgEntry | not-accessible | current | An entry in the configuration table for each voice analog interface. The entry is created when the voice analog hardware is detected. |
| 1.3.6.1.4.1.9.9.62.1.1.1.1.1 | ColumncvaIfCfgImpedance | read-write | current | Specifies the terminating impedance of voice analog interfaces. other - none of the following; arbitrary, within limits, for special cases. ohms600Real - 600 O… |
| 1.3.6.1.4.1.9.9.62.1.1.1.1.2 | ColumncvaIfCfgIntegratedDSP | read-only | current | Indicates whether the interface has an integrated Digital Signal processing (DSP) unit. |
| 1.3.6.1.4.1.9.9.62.1.1.2 | TablecvaIfStatusTable | not-accessible | current | The Analog Voice Status Table. It contains general information about the status of Analog Telephony interface including the error statistics. |
| 1.3.6.1.4.1.9.9.62.1.1.2.1 | RowcvaIfStatusEntry | not-accessible | current | An entry in the status table for each Analog voice interface. |
| 1.3.6.1.4.1.9.9.62.1.1.2.1.1 | ColumncvaIfStatusInfoType | read-only | current | The information transfer services for the current or last call. none - no information transfer service voice - analog voice. g3Fax - Group 3 FAX. |
| 1.3.6.1.4.1.9.9.62.1.1.2.1.2 | ColumncvaIfMaintenanceMode | read-only | current | Indicates the maintenance modes of the Analog voice interface. Managed system +=============+=============================+ | Voice | +===========+ telephony |… |
| 1.3.6.1.4.1.9.9.62.1.1.2.1.3 | ColumncvaIfStatusSignalErrors | read-only | current | Accumulated number of signaling protocol errors that are detected in the interface since system startup. |
| 1.3.6.1.4.1.9.9.62.1.2 | NodecvaIfEMObjects | |||
| 1.3.6.1.4.1.9.9.62.1.2.1 | TablecvaIfEMCfgTable | not-accessible | current | The E&M standard configuration table. It contains the current setting of E&M configurable parameters. |
| 1.3.6.1.4.1.9.9.62.1.2.1.1 | RowcvaIfEMCfgEntry | not-accessible | current | An entry in the standard configuration table for each E&M tie trunk interface. |
| 1.3.6.1.4.1.9.9.62.1.2.1.1.1 | ColumncvaIfEMCfgSignalType | read-write | current | The signaling type of E&M tie trunk interface. winkStart - the calling side seizes the line by going off-hook on its E lead but waits for a short off-hook 'win… |
| 1.3.6.1.4.1.9.9.62.1.2.1.1.2 | ColumncvaIfEMCfgOperation | read-write | current | Specify the operation of the E&M signal. twoWires - 2-wire operation. fourWires - 4-wire operation. |
| 1.3.6.1.4.1.9.9.62.1.2.1.1.3 | ColumncvaIfEMCfgType | read-write | current | Specifies the E&M Lead Signaling type. LEGEND: V = -48V /\/\/ = detector/resister X = normally open relay contact + = normally closed relay contact G = ground … |
| 1.3.6.1.4.1.9.9.62.1.2.1.1.4 | ColumncvaIfEMCfgDialType | read-write | current | Specifies the out dialing type of E&M interface. |
| 1.3.6.1.4.1.9.9.62.1.2.1.1.5 | ColumncvaIfEMCfgLmrMCap | read-write | current | The M lead behavior of E&M LMR interface. inact - The m-lead status should be ignored. audio - The m-lead status is used to control generating voice packet. di… |
| 1.3.6.1.4.1.9.9.62.1.2.1.1.6 | ColumncvaIfEMCfgLmrECap | read-write | current | The E lead behavior of E&M LMR interface. seize - The e-lead used as seize signal voice - The e-lead status is used to indicate voice packet received or not. i… |
| 1.3.6.1.4.1.9.9.62.1.2.1.1.7 | ColumncvaIfEMCfgAutoGainControl | read-write | current | This object is used to enabling/disabling automatic gain control(AGC) on this interface. AGC allows DSP to adjust the input voice volume and avoid rapid voice … |
| 1.3.6.1.4.1.9.9.62.1.2.2 | TablecvaIfEMStatusTable | not-accessible | current | The E&M interface Table. The table contains the status of the E&M tie trunk interface. |
| 1.3.6.1.4.1.9.9.62.1.2.2.1 | RowcvaIfEMStatusEntry | not-accessible | current | An entry in the status table for each E&M interface. |
| 1.3.6.1.4.1.9.9.62.1.2.2.1.1 | ColumncvaIfEMInSeizureActive | read-only | current | This object contains the incoming seizure state of the E&M interface. If the value is true, then the interface has an incoming trunk seizure active; otherwise,… |
| 1.3.6.1.4.1.9.9.62.1.2.2.1.2 | ColumncvaIfEMOutSeizureActive | read-only | current | This object contains the outgoing seizure state of the E&M interface. If the value is true, then the interface has an outgoing trunk seizure active; otherwise,… |
| 1.3.6.1.4.1.9.9.62.1.2.3 | TablecvaIfEMTimingTable | not-accessible | current | The E&M tie trunk Timing Parameters table. It contains the configuration of the various E&M signaling protocol timing parameters. |
| 1.3.6.1.4.1.9.9.62.1.2.3.1 | RowcvaIfEMTimingEntry | not-accessible | current | An entry in the E&M Timing Parameters Table for each E&M interface. |
| 1.3.6.1.4.1.9.9.62.1.2.3.1.1 | ColumncvaIfEMTimingDigitDuration | read-write | current | Outgoing DTMF digit duration in milliseconds. |
| 1.3.6.1.4.1.9.9.62.1.2.3.1.2 | ColumncvaIfEMTimingInterDigitDuration | read-write | current | Outgoing DTMF inter-digit duration in milliseconds. |
| 1.3.6.1.4.1.9.9.62.1.2.3.1.3 | ColumncvaIfEMTimingPulseRate | read-write | current | Outgoing pulse dialing rate in pulses per second (pps). |
| 1.3.6.1.4.1.9.9.62.1.2.3.1.4 | ColumncvaIfEMTimingPulseInterDigitDuration | read-write | current | Outgoing Pulse dialing inter-digit timing in milliseconds. |
| 1.3.6.1.4.1.9.9.62.1.2.3.1.5 | ColumncvaIfEMTimingClearWaitDuration | read-write | current | Time of Inactive seizure signal to declare call cleared. |
| 1.3.6.1.4.1.9.9.62.1.2.3.1.6 | ColumncvaIfEMTimingMaxWinkWaitDuration | read-write | current | Maximum time to wait from the outgoing seizure of the line to the time of sending out a wink-pulse. |
| 1.3.6.1.4.1.9.9.62.1.2.3.1.7 | ColumncvaIfEMTimingMaxWinkDuration | read-write | current | Maximum outgoing wink duration (between the wink-pulse leading edge and trailing edge) for wink start signaling. |
| 1.3.6.1.4.1.9.9.62.1.2.3.1.8 | ColumncvaIfEMTimingDelayStart | read-write | current | Minimum time to wait from outgoing seizure to out-dialing digits for delay start signaling. |
| 1.3.6.1.4.1.9.9.62.1.2.3.1.9 | ColumncvaIfEMTimingMaxDelayDuration | read-write | current | Maximum time to wait from outgoing seizure to out-dialing digits. If the far end does not allow to send digits after the duration specified in the object, a re… |
| 1.3.6.1.4.1.9.9.62.1.2.3.1.10 | ColumncvaIfEMTimingMinDelayPulseWidth | read-write | current | Minimum delay-dial pulse duration for incoming call. If the value of this object is 0, then no delay-dial is sent to the far end for the incoming call. |
| 1.3.6.1.4.1.9.9.62.1.2.3.1.11 | ColumncvaIfEMTimingVoiceHangover | read-write | current | The hangover time used to determine the casethere is no more voice packet arrived. |
| 1.3.6.1.4.1.9.9.62.1.2.3.1.12 | ColumncvaIfEMTimeoutLmrTeardown | read-write | current | LMR port tear down timeout. This object is relevant to the waiting time of teardown call on LMR port. if the value of this object is '-1', then the timeout is … |
| 1.3.6.1.4.1.9.9.62.1.2.3.1.13 | ColumncvaIfEMTimeoutPttXmt | read-write | current | This object signifies LMR port maxinum transmit time. This object is relevant to how long LMR port can continue transmit voice packet without pause. |
| 1.3.6.1.4.1.9.9.62.1.2.3.1.14 | ColumncvaIfEMTimeoutPttRcv | read-write | current | This object signifies LMR port maxinum receive time. This object is relevant to how long LMR port can continue receive voice packet without pause. |
| 1.3.6.1.4.1.9.9.62.1.2.3.1.15 | ColumncvaIfEMTimingDelayVoice | read-write | current | This object is relevant to how long DSP will delay sending the voice packet to the LMR port. |
| 1.3.6.1.4.1.9.9.62.1.3 | NodecvaIfFXOObjects | |||
| 1.3.6.1.4.1.9.9.62.1.3.1 | TablecvaIfFXOCfgTable | not-accessible | current | The FXO standard configuration table. It contains FXO configuration parameters, one entry per FXO interface. The configuration information of this table is set… |
| 1.3.6.1.4.1.9.9.62.1.3.1.1 | RowcvaIfFXOCfgEntry | not-accessible | current | An entry in the standard configuration table for each FXO interface. |
| 1.3.6.1.4.1.9.9.62.1.3.1.1.1 | ColumncvaIfFXOCfgSignalType | read-write | current | the signaling type of FXO interface. fxoLoopStart - loop start. fxoGroundStart - ground start. fxoCama - cama. |
| 1.3.6.1.4.1.9.9.62.1.3.1.1.2 | ColumncvaIfFXOCfgNumberRings | read-write | current | The number of rings detected before closing loop. |
| 1.3.6.1.4.1.9.9.62.1.3.1.1.3 | ColumncvaIfFXOCfgSupDisconnect | read-write | deprecated | Specifies whether a supervisory disconnect signal (CPC) will be presented to the interface when the connected party at the interface hangs up. |
| 1.3.6.1.4.1.9.9.62.1.3.1.1.4 | ColumncvaIfFXOCfgDialType | read-write | current | Specifies the out dialing type of FXO interface. |
| 1.3.6.1.4.1.9.9.62.1.3.1.1.5 | ColumncvaIfFXOCfgSupDisconnect2 | read-write | current | Specifies the type of supervisory disconnect signal (CPC) to be presented to the interface when the connected party at the interface hangs up. signal - power d… |
| 1.3.6.1.4.1.9.9.62.1.3.2 | TablecvaIfFXOStatusTable | not-accessible | current | The Foreign Exchange Office (FXO) interface Status Table. It contains hook status, ring detection and other states of the interface. |
| 1.3.6.1.4.1.9.9.62.1.3.2.1 | RowcvaIfFXOStatusEntry | not-accessible | current | An entry in the status table for each FXO interface. |
| 1.3.6.1.4.1.9.9.62.1.3.2.1.1 | ColumncvaIfFXOHookStatus | read-only | current | This object contains the hook status of FXO interface. onHook - Present the onHook to the connected equipment. offHook - Present the offHook to the connected e… |
| 1.3.6.1.4.1.9.9.62.1.3.2.1.2 | ColumncvaIfFXORingDetect | read-only | current | This object contains the ring detect indication. If the value is true, then the interface detects ring from PBX or CO; otherwise, it doesn't. |
| 1.3.6.1.4.1.9.9.62.1.3.2.1.3 | ColumncvaIfFXORingGround | read-only | current | This object contains the incoming ring ground indication. It is only valid when the cvaIfFXOCfgSignalType is fxoGroundStart. If the object is true, then the in… |
| 1.3.6.1.4.1.9.9.62.1.3.2.1.4 | ColumncvaIfFXOTipGround | read-only | current | This object contains the incoming tip ground indication. It is only valid when the cvaIfFXOCfgSignalType is fxoGroundStart. If the object is true, then the int… |
| 1.3.6.1.4.1.9.9.62.1.3.3 | TablecvaIfFXOTimingTable | not-accessible | current | The FXO interface Timing Parameters table. It contains the configuration of the various FXO signaling protocol timing parameters. |
| 1.3.6.1.4.1.9.9.62.1.3.3.1 | RowcvaIfFXOTimingEntry | not-accessible | current | An entry in the FXO Timing Parameters Table for each FXO interface. |
| 1.3.6.1.4.1.9.9.62.1.3.3.1.1 | ColumncvaIfFXOTimingDigitDuration | read-write | current | Outgoing DTMF digit duration in milliseconds. |
| 1.3.6.1.4.1.9.9.62.1.3.3.1.2 | ColumncvaIfFXOTimingInterDigitDuration | read-write | current | Outgoing DTMF inter-digit duration in milliseconds. |
| 1.3.6.1.4.1.9.9.62.1.3.3.1.3 | ColumncvaIfFXOTimingPulseRate | read-write | current | Outgoing pulse dialing rate in pulses per second (pps). |
| 1.3.6.1.4.1.9.9.62.1.3.3.1.4 | ColumncvaIfFXOTimingPulseInterDigitDuration | read-write | current | Outgoing pulse dialing inter-digit timing in milliseconds. |
| 1.3.6.1.4.1.9.9.62.1.4 | NodecvaIfFXSObjects | |||
| 1.3.6.1.4.1.9.9.62.1.4.1 | TablecvaIfFXSCfgTable | not-accessible | current | The FXS standard configuration table. It contains FXS configuration parameters, one entry per FXS interface. The configuration information of this table is set… |
| 1.3.6.1.4.1.9.9.62.1.4.1.1 | RowcvaIfFXSCfgEntry | not-accessible | current | An entry in the standard configuration table for each FXS interface. |
| 1.3.6.1.4.1.9.9.62.1.4.1.1.1 | ColumncvaIfFXSCfgSignalType | read-write | current | the signaling type of FXS interface. fxsLoopStart - loop start. fxsGroundStart - ground start. |
| 1.3.6.1.4.1.9.9.62.1.4.1.1.2 | ColumncvaIfFXSRingFrequency | read-write | current | the ring frequency to be used in the FXS interface. ringFrequency25 - ring frequency 25 Hertz. ringFrequency50 - ring frequency 50 Hertz. ringFrequency20 - rin… |
| 1.3.6.1.4.1.9.9.62.1.4.2 | TablecvaIfFXSStatusTable | not-accessible | current | The Foreign Exchange Station (FXS) interface Status Table. It contains hook status, ring active and other states of the interface. |
| 1.3.6.1.4.1.9.9.62.1.4.2.1 | RowcvaIfFXSStatusEntry | not-accessible | current | An entry in the status table for each FXS interface. |
| 1.3.6.1.4.1.9.9.62.1.4.2.1.1 | ColumncvaIfFXSHookStatus | read-only | current | This object contains the hook status of FXS interface. onHook - the connected equipment(e.g., phone) is onHook. offHook - the connected equipment is offHook. t… |
| 1.3.6.1.4.1.9.9.62.1.4.2.1.2 | ColumncvaIfFXSRingActive | read-only | current | This object contains the outgoing ring active indication. If the object value is true, then the interface is currently generating ring out to the Key Telephone… |
| 1.3.6.1.4.1.9.9.62.1.4.2.1.3 | ColumncvaIfFXSRingGround | read-only | current | This object contains the incoming ring ground indication. It is only valid when the cvaIfFXSCfgSignalType is fxsGroundStart. If the object is true, then the in… |
| 1.3.6.1.4.1.9.9.62.1.4.2.1.4 | ColumncvaIfFXSTipGround | read-only | current | This object contains the incoming tip ground indication. It is only valid when the cvaIfFXSCfgSignalType is fxsGroundStart. If the object is true, then the int… |
| 1.3.6.1.4.1.9.9.62.1.4.3 | TablecvaIfFXSTimingTable | not-accessible | current | The FXS interface Timing Parameters table. It contains the configuration of the various FXS signaling protocol timing parameters. |
| 1.3.6.1.4.1.9.9.62.1.4.3.1 | RowcvaIfFXSTimingEntry | not-accessible | current | An entry in the FXS Timing Parameters Table for each FXS interface. |
| 1.3.6.1.4.1.9.9.62.1.4.3.1.1 | ColumncvaIfFXSTimingDigitDuration | read-write | current | Outgoing DTMF digit duration in milliseconds. |
| 1.3.6.1.4.1.9.9.62.1.4.3.1.2 | ColumncvaIfFXSTimingInterDigitDuration | read-write | current | Outgoing DTMF inter-digit duration in milliseconds. |
| 1.3.6.1.4.1.9.9.62.3 | NodecvaIfMIBConformance | |||
| 1.3.6.1.4.1.9.9.62.3.1 | NodecvaIfMIBCompliances | |||
| 1.3.6.1.4.1.9.9.62.3.1.1 | CompliancecvaIfMIBCompliance | read-only | deprecated | The compliance statement for entities which implement the Cisco Analog Voice interface MIB |
| 1.3.6.1.4.1.9.9.62.3.1.2 | CompliancecvaIfMIBCompliance2 | read-only | deprecated | The compliance statement for entities which implement the Cisco Analog Voice interface MIB |
| 1.3.6.1.4.1.9.9.62.3.1.3 | CompliancecvaIfMIBCompliance3 | read-only | current | The compliance statement for entities which implement the Cisco Analog Voice interface MIB |
| 1.3.6.1.4.1.9.9.62.3.2 | NodecvaIfMIBGroups | |||
| 1.3.6.1.4.1.9.9.62.3.2.1 | GroupcvaIfGeneralGroup | current | The collection of objects providing general information about the Cisco Analog Voice interfaces. | |
| 1.3.6.1.4.1.9.9.62.3.2.2 | GroupcvaIfEMGroup | deprecated | The collection of objects providing information about the Cisco E&M trunk interface. | |
| 1.3.6.1.4.1.9.9.62.3.2.3 | GroupcvaIfFXOGroup | deprecated | The collection of objects providing information about the Cisco FXO interface. | |
| 1.3.6.1.4.1.9.9.62.3.2.4 | GroupcvaIfFXSGroup | current | The collection of objects providing information about the Cisco FXS interface. | |
| 1.3.6.1.4.1.9.9.62.3.2.5 | GroupcvaIfFXOGroup2 | current | The collection of objects providing information about the Cisco FXO interface. | |
| 1.3.6.1.4.1.9.9.62.3.2.6 | GroupcvaIfEMGroupRev1 | deprecated | The collection of objects providing information about the Cisco E&M trunk interface. | |
| 1.3.6.1.4.1.9.9.62.3.2.7 | GroupcvaIfEMGroupRev2 | current | The collection of objects providing information about the Cisco E&M trunk interface. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| InterfaceDialType | INTEGER { dtmf (1), pulse (2), mf (3) } | current | Specifies the out dialing type of E&M interface and FXO type interfaces. dtmf - DTMF digit. pulse - pulse. mf - mf digit. |