CISCO-WAN-3G-MIB
398 objects
This MIB module provides network management support for Cisco cellular 3G and 4G LTE WAN products. *** ABBREVIATIONS, ACRONYMS, AND SYMBOLS *** 1xRTT - 1 times Radio Transmission Technology. 3G - Third generation of mobile phones standards and technologies. 4G - Fourth generation of mobile phones standards and technologies Azimuth - Angle of rotation of a satellite Dish. BER - Bit Error Ratio. BS - Base Station. CDMA - Code Division Multiple Access. dB - decibel. dBm - power ratio in decibels (dB) of the measured power referenced to one milliwatt (mW). CnS - Control and Status proprietary protocol for managing the control and status of the modem. Ec/Io - ratio of received pilot energy, Ec, to total received energy or the total power spectral density, Io. EDGE - Enhanced Data rate for GSM Evolution. EPS - Evolved Packet System EVDO - EVolution Data Optimized. FDD - Frequency Division Duplexing GPRS - General Packet Radio Service. GSM - Global System for Mobile communications. GPS - Global Positioning System. HSDPA - High Speed Downlink Packet Access. HSPA - High Speed Packet Access. HSUPA - High Speed Uplink Packet Access. LBS - Location Based Service. LTE - Long Term Evolution MT - Mobile Termination. PDP - Packet Data Protocol. PLMN - Public Land Mobile Network. QoS - Quality of Service. RSSI - Received Signal Strength Indication. SDU - Service Data Unit. SER - SDU Error Ratio. SIM - Subscriber Identity Module. SMS - Short Messaging Service. SNR - Signal to Noise Ratio. TDD - Time Division Duplexing UMTS - Universal Mobile Telecommunication System. WCDMA - Wideband Code Division Multiple Access.
Imported Objects
| CISCO-SMI | ciscoMgmt |
| ENTITY-MIB | entPhysicalIndex entPhysicalName |
| IF-MIB | ifIndex |
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 Gauge32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString RowStatus TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.661 | IdentityciscoWan3gMIB | This MIB module provides network management support for Cisco cellular 3G and 4G LTE WAN products. *** ABBREVIATIONS, ACRONYMS, AND SYMBOLS *** 1xRTT - 1 times… | ||
| 1.3.6.1.4.1.9.9.661.0 | NodeciscoWan3gMIBNotifs | |||
| 1.3.6.1.4.1.9.9.661.0.1 | Notificationc3gModemUpNotif | current | This is the notification that the modem has been detected by host interface. Users can enable or disable the generation of this notification by using object c3… | |
| 1.3.6.1.4.1.9.9.661.0.2 | Notificationc3gModemDownNotif | current | This is the notification that the modem has not been detected by host interface, or has been disconnected from host interface. Users can enable or disable the … | |
| 1.3.6.1.4.1.9.9.661.0.3 | Notificationc3gServiceChangedNotif | current | Notification for service change event. Objects c3gPreviousServiceType and c3gCurrentServiceType will be included in the notification. Users can enable or disab… | |
| 1.3.6.1.4.1.9.9.661.0.4 | Notificationc3gNetworkChangedNotif | current | Notification for network change event. Objects c3gCurrentSid, c3gCurrentNid, c3gGsmMcc, c3gGsmMnc and c3gRoamingStatus will be included in the notification. Us… | |
| 1.3.6.1.4.1.9.9.661.0.5 | Notificationc3gConnectionStatusChangedNotif | current | Notification for connection status change event. Objects c3gConnectionStatus and c3gCurrentServiceType will be included in the notification. Users can use obje… | |
| 1.3.6.1.4.1.9.9.661.0.6 | Notificationc3gRssiOnsetNotif | current | If RSSI goes below c3gRssiOnsetNotifThreshold and the service bit in c3gRssiOnsetNotifFlag is set, this notification will be generated. Object c3gNotifRadioSer… | |
| 1.3.6.1.4.1.9.9.661.0.7 | Notificationc3gRssiAbateNotif | current | If RSSI goes above c3gRssiAbateNotifThreshold and the service bit in c3gRssiAbateNotifFlag is set, this notification will be generated. Object c3gNotifRadioSer… | |
| 1.3.6.1.4.1.9.9.661.0.8 | Notificationc3gEcIoOnsetNotif | current | If Ec/Io goes below c3gEcIoOnsetNotifThreshold and the service bit in c3gEcIoOnsetNotifFlag is set, this notification will be generated. Object c3gNotifRadioSe… | |
| 1.3.6.1.4.1.9.9.661.0.9 | Notificationc3gEcIoAbateNotif | current | If Ec/Io goes above c3gEcIoAbateNotifThreshold and the service bit in c3gEcIoAbateNotifFlag is set, this notification will be generated. Object c3gNotifRadioSe… | |
| 1.3.6.1.4.1.9.9.661.0.10 | Notificationc3gModemTemperOnsetNotif | current | If modem temperature goes above c3gModemTemperOnsetNotifThreshold and the value of c3gModemTemperOnsetNotifEnabled is 'true', this notification will be generat… | |
| 1.3.6.1.4.1.9.9.661.0.11 | Notificationc3gModemTemperAbateNotif | current | If modem temperature goes below c3gModemTemperAbateNotifThreshold and the value of c3gModemTemperAbateNotifEnabled is 'true', this notification will be generat… | |
| 1.3.6.1.4.1.9.9.661.0.12 | Notificationc3gModemTemperOnsetRecoveryNotif | current | This trap is generated as a recovery notification for c3gModemTemperOnsetNotif.This trap is generated when the current value of c3gModemTemperature goes below … | |
| 1.3.6.1.4.1.9.9.661.0.13 | Notificationc3gModemTemperAbateRecoveryNotif | current | This trap is generated as a recovery notification for c3gModemTemperAbateNotif.This trap is generated when the current value of c3gModemTemperature goes above … | |
| 1.3.6.1.4.1.9.9.661.1 | NodeciscoWan3gMIBObjects | |||
| 1.3.6.1.4.1.9.9.661.1.1 | Tablec3gWanCommonTable | not-accessible | current | Cellular common objects table which is technology independent. |
| 1.3.6.1.4.1.9.9.661.1.1.1 | Rowc3gWanCommonEntry | not-accessible | current | An entry (conceptual row) in the c3gWanCommonTable. |
| 1.3.6.1.4.1.9.9.661.1.1.1.1 | Columnc3gStandard | read-only | current | Cellular Standard: GSM (Global System for Mobile communications, 3GPP), CDMA (Code Division Multiple Access, 3GPP-2). GSM standard also include 4G-LTE technolo… |
| 1.3.6.1.4.1.9.9.661.1.1.1.2 | Columnc3gCapability | read-only | current | Cellular service capability. It currently includes the 2G, 3G and 4G-LTE standard. |
| 1.3.6.1.4.1.9.9.661.1.1.1.3 | Columnc3gModemState | read-only | current | Cellular modem state, up(2) indicates modem can be detected and down(3) indicates modem can not be detected. |
| 1.3.6.1.4.1.9.9.661.1.1.1.4 | Columnc3gPreviousServiceType | read-only | current | This object indicates the previous service type when service type changes. |
| 1.3.6.1.4.1.9.9.661.1.1.1.5 | Columnc3gCurrentServiceType | read-only | current | This object indicates the current service type when service type changes. |
| 1.3.6.1.4.1.9.9.661.1.1.1.6 | Columnc3gRoamingStatus | read-only | current | Cellular current roaming status. |
| 1.3.6.1.4.1.9.9.661.1.1.1.7 | Columnc3gCurrentSystemTime | read-only | current | Cellular current system time received from base station. |
| 1.3.6.1.4.1.9.9.661.1.1.1.8 | Columnc3gConnectionStatus | read-only | current | Indicates the current connection status. |
| 1.3.6.1.4.1.9.9.661.1.1.1.9 | Columnc3gNotifRadioService | read-only | current | This object is used as one of the var-bind object when notification for RSSI or Ec/Io is generated. This object indicates which service generates the notificat… |
| 1.3.6.1.4.1.9.9.661.1.1.1.10 | Columnc3gNotifRssi | read-only | current | This object is used as one of the var-bind object when notification for RSSI is generated. The relevant RSSI will be copied into c3gNotifRssi which corresponds… |
| 1.3.6.1.4.1.9.9.661.1.1.1.11 | Columnc3gNotifEcIo | read-only | current | This object is used as one of the var-bind object when notification for Ec/Io is generated. The relevant Ec/Io will be copied into c3gNotifEcIo which correspon… |
| 1.3.6.1.4.1.9.9.661.1.1.1.12 | Columnc3gModemTemperature | read-only | current | The modem temperature. |
| 1.3.6.1.4.1.9.9.661.1.1.1.13 | Columnc3gRssiOnsetNotifThreshold | read-write | current | The RSSI onset threshold value. If RSSI goes below the threshold and the service bit in c3gRssiOnsetNotifFlag is set, the c3gRssiOnsetNotif notification for th… |
| 1.3.6.1.4.1.9.9.661.1.1.1.14 | Columnc3gRssiAbateNotifThreshold | read-write | current | The RSSI abate threshold value. If RSSI goes above the threshold and the service bit in c3gRssiAbateNotifFlag is set, the c3gRssiAbateNotif notification for th… |
| 1.3.6.1.4.1.9.9.661.1.1.1.15 | Columnc3gEcIoOnsetNotifThreshold | read-write | current | The EcIo onset threshold value. If EcIo goes below the threshold and the service bit in c3gEcIoOnsetNotifFlag is set, the c3gEcIoOnsetNotif notification for th… |
| 1.3.6.1.4.1.9.9.661.1.1.1.16 | Columnc3gEcIoAbateNotifThreshold | read-write | current | The threshold value that if EcIo goes above the threshold and the service bit in c3gEcIoAbateNotifFlag is set, the c3gEcIoAbateNotif notification for that serv… |
| 1.3.6.1.4.1.9.9.661.1.1.1.17 | Columnc3gModemTemperOnsetNotifThreshold | read-write | current | The modem temperature onset threshold value. If modem temperature goes above the threshold and the value of c3gModemTemperOnsetNotifEnabled is 'true', the c3gM… |
| 1.3.6.1.4.1.9.9.661.1.1.1.18 | Columnc3gModemTemperAbateNotifThreshold | read-write | current | The modem temperature abate threshold value. If modem temperature goes below the threshold and the value of c3gModemTemperAbateNotifEnabled is 'true', the c3gM… |
| 1.3.6.1.4.1.9.9.661.1.1.1.19 | Columnc3gModemReset | read-write | current | This object is used to reset or power-cycle the modem. |
| 1.3.6.1.4.1.9.9.661.1.1.1.20 | Columnc3gModemUpNotifEnabled | read-write | current | This object is used to enable/disable the generation of modem up notification c3gModemUpNotif. |
| 1.3.6.1.4.1.9.9.661.1.1.1.21 | Columnc3gModemDownNotifEnabled | read-write | current | This object is used to enable/disable the generation of modem down notification c3gModemDownNotif. |
| 1.3.6.1.4.1.9.9.661.1.1.1.22 | Columnc3gServiceChangedNotifEnabled | read-write | current | This object is used to enable/disable the generation of service changed notification c3gServiceChangedNotif. |
| 1.3.6.1.4.1.9.9.661.1.1.1.23 | Columnc3gNetworkChangedNotifEnabled | read-write | current | This object is used to enable/disable the generation of network changed notification c3gNetworkChangedNotif. |
| 1.3.6.1.4.1.9.9.661.1.1.1.24 | Columnc3gConnectionStatusChangedNotifFlag | read-write | current | This object is the flag bitmap to control the generation of notification c3gConnectionStatusChangedNotif. e.g. setting bit 0 (error(0)) to 1 and bit 4 (disconn… |
| 1.3.6.1.4.1.9.9.661.1.1.1.25 | Columnc3gRssiOnsetNotifFlag | read-write | current | This object is the flag bitmap to control the generation of notification c3gRssiOnsetNotif. Each bit represents a service as defined in C3gServiceCapability, s… |
| 1.3.6.1.4.1.9.9.661.1.1.1.26 | Columnc3gRssiAbateNotifFlag | read-write | current | This object is the flag bitmap to control the generation of notification c3gRssiAbateNotif. Each bit represents a service as defined in C3gServiceCapability, s… |
| 1.3.6.1.4.1.9.9.661.1.1.1.27 | Columnc3gEcIoOnsetNotifFlag | read-write | current | This object is the flag bitmap to control the generation of notification c3gEcIoOnsetNotif. Each bit represents a service as defined in C3gServiceCapability, s… |
| 1.3.6.1.4.1.9.9.661.1.1.1.28 | Columnc3gEcIoAbateNotifFlag | read-write | current | This object is the flag bitmap to control the generation of notification c3gEcIoAbateNotif. Each bit represents a service as defined in C3gServiceCapability, s… |
| 1.3.6.1.4.1.9.9.661.1.1.1.29 | Columnc3gModemTemperOnsetNotifEnabled | read-write | current | This object is used to enable/disable the generation of c3gModemTemperOnsetNotif notification. |
| 1.3.6.1.4.1.9.9.661.1.1.1.30 | Columnc3gModemTemperAbateNotifEnabled | read-write | current | This object is used to enable/disable the generation of c3gModemTemperAbateNotif notification. |
| 1.3.6.1.4.1.9.9.661.1.1.1.31 | Columnc3gGpsState | read-write | current | This object is used to determine or enable/disable the GPS state. |
| 1.3.6.1.4.1.9.9.661.1.2 | Nodec3gWanCdma | |||
| 1.3.6.1.4.1.9.9.661.1.2.1 | Tablec3gCdmaSessionTable | not-accessible | current | This table describes wireless session (link) created when a modem connects to a particular cellular network. One or more logical calls can be placed over wirel… |
| 1.3.6.1.4.1.9.9.661.1.2.1.1 | Rowc3gCdmaSessionEntry | not-accessible | current | An entry (conceptual row) in the c3gCdmaSessionTable. |
| 1.3.6.1.4.1.9.9.661.1.2.1.1.1 | Columnc3gCdmaTotalCallDuration | read-only | current | Total duration of all calls. |
| 1.3.6.1.4.1.9.9.661.1.2.1.1.2 | Columnc3gCdmaTotalTransmitted | read-only | current | Total data transmitted for all calls. It is the total amount of data transmitted by modem, not to be confused with the number of bytes transmitted through the … |
| 1.3.6.1.4.1.9.9.661.1.2.1.1.3 | Columnc3gCdmaTotalReceived | read-only | current | Total data received for all calls. It is the total amount of data received by modem, not to be confused with the number of bytes received from the interface. |
| 1.3.6.1.4.1.9.9.661.1.2.1.1.4 | Columnc3gHdrDdtmPreference | read-write | current | HDR Data Dedicated Transmission Mode (DDTM) preference: unknown(1) - DDTM preference is unknown off(2) - DDTM preference set to OFF on(3) - DDTM preference set… |
| 1.3.6.1.4.1.9.9.661.1.2.2 | Tablec3gCdmaConnectionTable | not-accessible | current | Cellular 3G CDMA connection table. This table describes logical connections/calls over wireless link, the wireless link is described in c3gCdmaSessionTable. |
| 1.3.6.1.4.1.9.9.661.1.2.2.1 | Rowc3gCdmaConnectionEntry | not-accessible | current | An entry (conceptual row) in the c3gCdmaConnectionTable. |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.1 | Columnc3gOutgoingCallNumber | read-only | current | Phone number of outgoing call. |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.2 | Columnc3gHdrAtState | read-only | current | High Data Rate (HDR) Access Terminal (AT) state. |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.3 | Columnc3gHdrSessionState | read-only | current | High Data Rate (HDR) session state. |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.4 | Columnc3gUati | read-only | current | Unicast Access Terminal Identifier (UATI), AT seeking access to the 1 times EV-DO system receives a UATI allocated from the system after setting up a radio tra… |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.5 | Columnc3gColorCode | read-only | current | Color code. A sync channel may be used by the base station to communicate administrative information to a mobile station. For example, a base station may trans… |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.6 | Columnc3gRati | read-only | current | Random Access Terminal Identifier (RATI). AT transmits a UATI request message to the ANC using the RATI to make a UATI allocation request. |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.7 | Columnc3gHdrSessionDuration | read-only | current | HDR connection session duration. It is the duration between c3gHdrSessionStart and c3gHdrSessionEnd. |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.8 | Columnc3gHdrSessionStart | read-only | current | HDR connection session starting time. |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.9 | Columnc3gHdrSessionEnd | read-only | current | HDR connection session ending time. |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.10 | Columnc3gAuthStatus | read-only | current | Connection authentication status: unknown(1) - authentication status is unknown notAuthenticated(2) - not yet authenticated. authenticated(3) - authenticated. … |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.11 | Columnc3gHdrDrc | read-only | current | High Data Rate (HDR) Data Rate Control (DRC). AT provides requests for data transmissions by sending a Data Rate Control, DRC, message via a specific channel r… |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.12 | Columnc3gHdrDrcCover | read-only | current | HDR DRC cover. The DRC cover is a coding applied to identify the sector from which the data is to be transmitted. In one embodiment, the DRC cover is a Walsh c… |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.13 | Columnc3gHdrRri | read-only | current | HDR Rate Request Indicator (RRI). RRI provides the structure of a frame currently being transmitted when frames are transmitted at different rates. Services at… |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.14 | Columnc3gMobileIpErrorCode | read-only | current | Mobile IP error code (please refer to RFC 2002). |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.15 | Columnc3gCdmaCurrentTransmitted | read-only | current | Current number of bytes transmitted by modem for current connection. |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.16 | Columnc3gCdmaCurrentReceived | read-only | current | Current number of bytes received by modem for current connection. |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.17 | Columnc3gCdmaCurrentCallStatus | read-only | current | Current call status. |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.18 | Columnc3gCdmaCurrentCallDuration | read-only | current | Current call duration. |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.19 | Columnc3gCdmaCurrentCallType | read-only | current | Current call type. |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.20 | Columnc3gCdmaLastCallDisconnReason | read-only | current | Last call disconnect reason: unknown(1) - Unknown modemOffline(2) - Modem offline modemCdmaLocTilPowCyc(3) - Modem CDMA locked till power cycle noService(4) - … |
| 1.3.6.1.4.1.9.9.661.1.2.2.1.21 | Columnc3gCdmaLastConnError | read-only | current | Last connect error: none(1) - None invalidClientId(2) - Invalid client ID badCallType(3) - Bad call type badServiceType(4) - Bad service type expectingNumber(5… |
| 1.3.6.1.4.1.9.9.661.1.2.3 | Tablec3gCdmaIdentityTable | not-accessible | current | Cellular 3G CDMA identity table. |
| 1.3.6.1.4.1.9.9.661.1.2.3.1 | Rowc3gCdmaIdentityEntry | not-accessible | current | An entry (conceptual row) in the c3gCdmaIdentityTable. |
| 1.3.6.1.4.1.9.9.661.1.2.3.1.1 | Columnc3gEsn | read-only | current | This object indicates Electronic Serial Number (ESN). |
| 1.3.6.1.4.1.9.9.661.1.2.3.1.2 | Columnc3gModemActivationStatus | read-only | current | Modem activation status. |
| 1.3.6.1.4.1.9.9.661.1.2.3.1.3 | Columnc3gAccountActivationDate | read-only | current | Modem account activation date. |
| 1.3.6.1.4.1.9.9.661.1.2.3.1.4 | Columnc3gCdmaRoamingPreference | read-write | current | This object indicates the roaming preference: unknown(1) - preference unknown home(2) - home networks only affiliated(3) - roaming on affiliated networks any(4… |
| 1.3.6.1.4.1.9.9.661.1.2.3.1.5 | Columnc3gPrlVersion | read-only | current | Preferred Roaming List (PRL) version. |
| 1.3.6.1.4.1.9.9.661.1.2.3.1.6 | Columnc3gMdn | read-write | current | Mobile Directory Number (MDN), a dialable number assigned to a wireless phone. |
| 1.3.6.1.4.1.9.9.661.1.2.3.1.7 | Columnc3gMsid | read-write | current | Mobile Station Identifier (MSID), MSID is utilized to distinguish the mobile station being programmed from other mobile stations during messaging and paging pr… |
| 1.3.6.1.4.1.9.9.661.1.2.3.1.8 | Columnc3gMsl | read-write | current | Mobile Subscriber Lock (MSL). |
| 1.3.6.1.4.1.9.9.661.1.2.4 | Tablec3gCdmaNetworkTable | not-accessible | current | Cellular 3G CDMA network table. |
| 1.3.6.1.4.1.9.9.661.1.2.4.1 | Rowc3gCdmaNetworkEntry | not-accessible | current | An entry (conceptual row) in the c3gCdmaNetworkTable. |
| 1.3.6.1.4.1.9.9.661.1.2.4.1.1 | Columnc3gCdmaCurrentServiceStatus | read-only | current | Current service status. |
| 1.3.6.1.4.1.9.9.661.1.2.4.1.2 | Columnc3gCdmaHybridModePreference | read-write | current | This object indicates the hybrid mode preference: unknown(1) - preference unknown hybrid(2) - connect to EV-DO/1xRTT services evDoOnly(3) - connect to only EV-… |
| 1.3.6.1.4.1.9.9.661.1.2.4.1.3 | Columnc3gCdmaCurrentRoamingStatus | read-only | current | Current 1xRTT roaming status, roaming is a general term in wireless telecommunications that refers to the extending of connectivity service in a location that … |
| 1.3.6.1.4.1.9.9.661.1.2.4.1.4 | Columnc3gCurrentIdleDigitalMode | read-only | current | Current idle digital mode: unknown(1) - service is unknown noService(2) - no service amps(3) - Advanced Mobile Phone Service (AMPS) cdma(4) - Code Division Mul… |
| 1.3.6.1.4.1.9.9.661.1.2.4.1.5 | Columnc3gCurrentSid | read-write | current | Current System Identifier (SID), SID is a 15-bit numeric identifiers used by cellular systems to identify the home system of a cellular telephone and by the ce… |
| 1.3.6.1.4.1.9.9.661.1.2.4.1.6 | Columnc3gCurrentNid | read-write | current | Current Network Identification (NID), NID is a 16-bit numeric identifiers used by cellular systems. Value of '-1' indicates NID is 'Not Applicable'. |
| 1.3.6.1.4.1.9.9.661.1.2.4.1.7 | Columnc3gCurrentCallSetupMode | read-write | current | Current call setup mode. The 1xEV-DO system supports packet data connections to a public or private data network using either mobile IP or simple IP protocol. … |
| 1.3.6.1.4.1.9.9.661.1.2.4.1.8 | Columnc3gSipUsername | read-write | current | Simple IP (SIP) user name. |
| 1.3.6.1.4.1.9.9.661.1.2.4.1.9 | Columnc3gSipPassword | read-write | current | Simple IP (SIP) password. |
| 1.3.6.1.4.1.9.9.661.1.2.4.1.10 | Columnc3gServingBaseStationLongitude | read-only | current | Longitude of the serving base station. |
| 1.3.6.1.4.1.9.9.661.1.2.4.1.11 | Columnc3gServingBaseStationLatitude | read-only | current | Latitude of the serving base station. |
| 1.3.6.1.4.1.9.9.661.1.2.5 | Nodec3gCdmaProfile | |||
| 1.3.6.1.4.1.9.9.661.1.2.5.1 | Tablec3gCdmaProfileCommonTable | not-accessible | current | Cellular 3G CDMA profile common table. |
| 1.3.6.1.4.1.9.9.661.1.2.5.1.1 | Rowc3gCdmaProfileCommonEntry | not-accessible | current | An entry (conceptual row) in the c3gCdmaProfileCommonTable. |
| 1.3.6.1.4.1.9.9.661.1.2.5.1.1.1 | Columnc3gNumberOfDataProfileConfigurable | read-write | current | The number of data profiles configurable. |
| 1.3.6.1.4.1.9.9.661.1.2.5.1.1.2 | Columnc3gCurrentActiveDataProfile | read-write | current | The current active data profile. |
| 1.3.6.1.4.1.9.9.661.1.2.5.2 | Tablec3gCdmaProfileTable | not-accessible | current | Cellular 3G CDMA profile table. |
| 1.3.6.1.4.1.9.9.661.1.2.5.2.1 | Rowc3gCdmaProfileEntry | not-accessible | current | An entry (conceptual row) in the c3gCdmaProfileTable. |
| 1.3.6.1.4.1.9.9.661.1.2.5.2.1.1 | Columnc3gCdmaProfileIndex | not-accessible | current | Profile index, combined with entPhysicalIndex to access the profile table c3gCdmaProfileTable. |
| 1.3.6.1.4.1.9.9.661.1.2.5.2.1.2 | Columnc3gNai | read-write | current | Network Access Identifier (NAI). NAI is required to identify the mobile user and the network the mobile user intended to access. The NAI is provided by the mob… |
| 1.3.6.1.4.1.9.9.661.1.2.5.2.1.3 | Columnc3gAaaPassword | read-write | current | This object indicates the password for AAA. |
| 1.3.6.1.4.1.9.9.661.1.2.5.2.1.4 | Columnc3gMnHaSs | read-write | current | Mobile Node (MN) Home Agent (HA) Shared Secret (SS) setting: set(1) - shared secret is set notSet(2) - shared secret is not set |
| 1.3.6.1.4.1.9.9.661.1.2.5.2.1.5 | Columnc3gMnHaSpi | read-write | current | Mobile Node (MN) Home Agent (HA) Security Parameter Index (SPI). |
| 1.3.6.1.4.1.9.9.661.1.2.5.2.1.6 | Columnc3gMnAaaSs | read-write | current | Mobile Node (MN) Authentication Authorization Accounting (AAA) Shared Secret (SS) setting: set(1) - shared secret is set notSet(2) - shared secret is not set |
| 1.3.6.1.4.1.9.9.661.1.2.5.2.1.7 | Columnc3gMnAaaSpi | read-write | current | Mobile Node (MN) Authentication Authorization Accounting (AAA) Security Parameter Index (SPI). |
| 1.3.6.1.4.1.9.9.661.1.2.5.2.1.8 | Columnc3gReverseTunnelPreference | read-write | current | Reverse tunnel preference. |
| 1.3.6.1.4.1.9.9.661.1.2.5.2.1.9 | Columnc3gHomeAddrType | read-write | current | A value that represents the type of the IP Address stored in the object c3gHomeAddr. |
| 1.3.6.1.4.1.9.9.661.1.2.5.2.1.10 | Columnc3gHomeAddr | read-write | current | A unicast routable address assigned to a Mobile Node, used as the permanent address of the Mobile Node. |
| 1.3.6.1.4.1.9.9.661.1.2.5.2.1.11 | Columnc3gPriHaAddrType | read-write | current | A value that represents the type of the IP Address stored in the object c3gPriHaAddr. |
| 1.3.6.1.4.1.9.9.661.1.2.5.2.1.12 | Columnc3gPriHaAddr | read-write | current | The primary home agent address. |
| 1.3.6.1.4.1.9.9.661.1.2.5.2.1.13 | Columnc3gSecHaAddrType | read-write | current | A value that represents the type of the IP Address stored in the object c3gSecHaAddr. |
| 1.3.6.1.4.1.9.9.661.1.2.5.2.1.14 | Columnc3gSecHaAddr | read-write | current | The secondary home agent address. |
| 1.3.6.1.4.1.9.9.661.1.2.6 | Nodec3gCdmaRadio | |||
| 1.3.6.1.4.1.9.9.661.1.2.6.1 | Tablec3gCdma1xRttRadioTable | not-accessible | current | Cellular 3G CDMA 1xRTT radio table. |
| 1.3.6.1.4.1.9.9.661.1.2.6.1.1 | Rowc3gCdma1xRttRadioEntry | not-accessible | current | An entry (conceptual row) in the c3gCdma1xRttRadioTable. |
| 1.3.6.1.4.1.9.9.661.1.2.6.1.1.1 | Columnc3gCurrent1xRttRssi | read-only | current | Current 1xRTT RSSI value. |
| 1.3.6.1.4.1.9.9.661.1.2.6.1.1.2 | Columnc3gCurrent1xRttEcIo | read-only | current | Current 1xRTT Ec/Io value. |
| 1.3.6.1.4.1.9.9.661.1.2.6.1.1.3 | Columnc3gCurrent1xRttChannelNumber | read-only | current | Current 1xRTT channel number. Current channel number to which the modem is attached to the base station. Value of '-1' indicates 'No Service'. |
| 1.3.6.1.4.1.9.9.661.1.2.6.1.1.4 | Columnc3gCurrent1xRttChannelState | read-only | current | Current 1xRTT channel state. Indicates whether the modem is scanning or has acquired the channel. |
| 1.3.6.1.4.1.9.9.661.1.2.6.2 | Tablec3gCdma1xRttBandClassTable | not-accessible | current | Cellular 3G CDMA 1xRTT band class table. This table contains band class information for each available band. |
| 1.3.6.1.4.1.9.9.661.1.2.6.2.1 | Rowc3gCdma1xRttBandClassEntry | not-accessible | current | An entry (conceptual row) in the c3gCdma1xRttBandClassTable. |
| 1.3.6.1.4.1.9.9.661.1.2.6.2.1.1 | Columnc3gBandClassIndex | not-accessible | current | Band class index, combined with entPhysicalIndex to access the band class table. |
| 1.3.6.1.4.1.9.9.661.1.2.6.2.1.2 | Columnc3g1xRttBandClass | read-only | current | This object contains 1xRTT band class. |
| 1.3.6.1.4.1.9.9.661.1.2.6.3 | Tablec3gCdmaEvDoRadioTable | not-accessible | current | Cellular 3G CDMA EV-DO radio table. |
| 1.3.6.1.4.1.9.9.661.1.2.6.3.1 | Rowc3gCdmaEvDoRadioEntry | not-accessible | current | An entry (conceptual row) in the c3gCdmaEvDoRadioTable. |
| 1.3.6.1.4.1.9.9.661.1.2.6.3.1.1 | Columnc3gCurrentEvDoRssi | read-only | current | Current EV-DO RSSI value. |
| 1.3.6.1.4.1.9.9.661.1.2.6.3.1.2 | Columnc3gCurrentEvDoEcIo | read-only | current | Current EV-DO Ec/Io value. |
| 1.3.6.1.4.1.9.9.661.1.2.6.3.1.3 | Columnc3gCurrentEvDoChannelNumber | read-only | current | Current EV-DO channel number. Current channel number to which the modem is attached to the base station. Value of '-1' indicates 'No Service'. |
| 1.3.6.1.4.1.9.9.661.1.2.6.3.1.4 | Columnc3gSectorId | read-only | current | Sector ID of the base station to which the modem is attached. |
| 1.3.6.1.4.1.9.9.661.1.2.6.3.1.5 | Columnc3gSubnetMask | read-only | current | Subnet mask of the sector, not to be confused with the IP subnet mask. |
| 1.3.6.1.4.1.9.9.661.1.2.6.3.1.6 | Columnc3gHdrColorCode | read-only | current | Color code of the sector. |
| 1.3.6.1.4.1.9.9.661.1.2.6.3.1.7 | Columnc3gPnOffset | read-only | current | PN offset. PN offset is a time offset from the beginning of the well-known pseudo-random noise sequence that is used to spread the signal from the base station. |
| 1.3.6.1.4.1.9.9.661.1.2.6.3.1.8 | Columnc3gRxMainGainControl | read-only | current | Received main gain control for the modem. value of '-1' indicates the received main gain control is unavailable. |
| 1.3.6.1.4.1.9.9.661.1.2.6.3.1.9 | Columnc3gRxDiversityGainControl | read-only | current | Received diversity for the modem. value of '-1' indicates the received diversity is unavailable. |
| 1.3.6.1.4.1.9.9.661.1.2.6.3.1.10 | Columnc3gTxTotalPower | read-only | current | Transmit total power. |
| 1.3.6.1.4.1.9.9.661.1.2.6.3.1.11 | Columnc3gTxGainAdjust | read-only | current | Transmit gain adjust. |
| 1.3.6.1.4.1.9.9.661.1.2.6.3.1.12 | Columnc3gCarrierToInterferenceRatio | read-only | current | Carrier to interference ratio. Carrier-to-Interference ratio (C/I) is the ratio of power in an RF carrier to the interference power in the channel. |
| 1.3.6.1.4.1.9.9.661.1.2.6.4 | Tablec3gCdmaEvDoBandClassTable | not-accessible | current | Cellular 3G CDMA EV-DO band class table. This table contains band class information for each available band. |
| 1.3.6.1.4.1.9.9.661.1.2.6.4.1 | Rowc3gCdmaEvDoBandClassEntry | not-accessible | current | An entry (conceptual row) in the c3gCdmaEvDoBandClassTable. |
| 1.3.6.1.4.1.9.9.661.1.2.6.4.1.1 | Columnc3gEvDoBandClass | read-only | current | This object contains EV-DO band class. |
| 1.3.6.1.4.1.9.9.661.1.2.6.5 | Tablec3gCdmaHistoryTable | not-accessible | current | Cellular 3G CDMA history table. The history of RSSI are carried in an octet of string. Each octet in the octet string has a value from 0 to 150 and the 255 val… |
| 1.3.6.1.4.1.9.9.661.1.2.6.5.1 | Rowc3gCdmaHistoryEntry | not-accessible | current | An entry (conceptual row) in the c3gCdmaHistoryTable. |
| 1.3.6.1.4.1.9.9.661.1.2.6.5.1.1 | Columnc3gCdmaHistory1xRttRssiPerSecond | read-only | current | Per-second 1xRTT RSSI history. This object contains a per-second history of 1xRTT RSSI values for the last 60 seconds. |
| 1.3.6.1.4.1.9.9.661.1.2.6.5.1.2 | Columnc3gCdmaHistory1xRttRssiPerMinute | read-only | current | Per-minute 1xRTT weakest RSSI value history. This object contains a per-minute history of 1xRTT weakest RSSI values for the last 60 minutes. The octet in the s… |
| 1.3.6.1.4.1.9.9.661.1.2.6.5.1.3 | Columnc3gCdmaHistory1xRttRssiPerHour | read-only | current | Per-hour 1xRTT weakest RSSI value history. This object contains a per-hour history of 1xRTT weakest RSSI values for the last 72 hours. The octet in the string … |
| 1.3.6.1.4.1.9.9.661.1.2.6.5.1.4 | Columnc3gCdmaHistoryEvDoRssiPerSecond | read-only | current | Per-second EV-DO RSSI history. This object contains a per-second history of EV-DO RSSI values for the last 60 seconds. |
| 1.3.6.1.4.1.9.9.661.1.2.6.5.1.5 | Columnc3gCdmaHistoryEvDoRssiPerMinute | read-only | current | Per-minute EV-DO weakest RSSI value history. This object contains a per-minute history of EV-DO weakest RSSI values for the last 60 minutes. The octet in the s… |
| 1.3.6.1.4.1.9.9.661.1.2.6.5.1.6 | Columnc3gCdmaHistoryEvDoRssiPerHour | read-only | current | Per-hour EV-DO weakest RSSI value history. This object contains a per-hour history of EV-DO weakest RSSI values for the last 72 hours. The octet in the string … |
| 1.3.6.1.4.1.9.9.661.1.2.7 | Nodec3gCdmaSecurity | |||
| 1.3.6.1.4.1.9.9.661.1.2.7.1 | Tablec3gCdmaSecurityTable | not-accessible | current | Cellular 3G CDMA security table. |
| 1.3.6.1.4.1.9.9.661.1.2.7.1.1 | Rowc3gCdmaSecurityEntry | not-accessible | current | An entry (conceptual row) in the c3gCdmaSecurityTable. |
| 1.3.6.1.4.1.9.9.661.1.2.7.1.1.1 | Columnc3gCdmaPinSecurityStatus | read-write | current | CDMA Personal Identification Number (PIN) security: unknown(1) - PIN security unknown locked(2) - PIN security is locked unlocked(3) - PIN security is unlocked |
| 1.3.6.1.4.1.9.9.661.1.2.7.1.1.2 | Columnc3gCdmaPowerUpLockStatus | read-write | current | CDMA power up lock: unknown(1) - power up lock unknown enabled(2) - power up lock enabled disabled(3) - power up lock disabled |
| 1.3.6.1.4.1.9.9.661.1.3 | Nodec3gWanGsm | |||
| 1.3.6.1.4.1.9.9.661.1.3.1 | Tablec3gGsmIdentityTable | not-accessible | current | . |
| 1.3.6.1.4.1.9.9.661.1.3.1.1 | Rowc3gGsmIdentityEntry | not-accessible | current | An entry (conceptual row) in the c3gGsmIdentityTable. |
| 1.3.6.1.4.1.9.9.661.1.3.1.1.1 | Columnc3gImsi | read-only | current | International Mobile Subscriber Identifier (IMSI), a unique 15-digit code used to identify an individual user on a GSM/LTE network. |
| 1.3.6.1.4.1.9.9.661.1.3.1.1.2 | Columnc3gImei | read-only | current | International Mobile Equipment Identifier (IMEI), a unique 15 or 17 digit code used to identify an individual mobile station to a GSM, UMTS or LTE network. |
| 1.3.6.1.4.1.9.9.661.1.3.1.1.3 | Columnc3gIccId | read-only | current | This object indicates the Integrated Circuit Card ID (ICCID). The ICCID is defined by the ITU-T recommendation E.118. ICCIDs are stored in the SIM cards and ar… |
| 1.3.6.1.4.1.9.9.661.1.3.1.1.4 | Columnc3gMsisdn | read-write | current | This object indicates the Mobile Subscriber Integrated Services Digital Network Number (MSISDN). It is a number uniquely identifying a subscription in a GSM, U… |
| 1.3.6.1.4.1.9.9.661.1.3.1.1.5 | Columnc3gFsn | read-only | current | Forward Sequence Number (FSN), a message acknowledgement method using sequence number in the forward direction. |
| 1.3.6.1.4.1.9.9.661.1.3.1.1.6 | Columnc3gModemStatus | read-only | current | Modem status: unknown(1) - modem status is unknown offLine(2) - modem is off line onLine(3) - modem is on line lowPowerMode(4) - modem is in the low power mode |
| 1.3.6.1.4.1.9.9.661.1.3.1.1.7 | Columnc3gGsmRoamingPreference | read-write | current | This object indicates the roaming preference. |
| 1.3.6.1.4.1.9.9.661.1.3.2 | Tablec3gGsmNetworkTable | not-accessible | current | Cellular GSM Network table. This table is applicable in both 3G and 4G-LTE technology mode |
| 1.3.6.1.4.1.9.9.661.1.3.2.1 | Rowc3gGsmNetworkEntry | not-accessible | current | An entry (conceptual row) in the c3gGsmNetworkTable. |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.1 | Columnc3gGsmLac | read-only | current | Location Area Code (LAC), also called as Tracking Area Code (TAC) in LTE standard. LAC/TAC is given by the base station. |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.2 | Columnc3gGsmCurrentServiceStatus | read-only | current | Current Service Status: unknown(1) - current service status is unknown noService(2) - no service normal(3) - service status is normal emergencyOnly(4) - emerge… |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.3 | Columnc3gGsmCurrentServiceError | read-only | current | Current service error: unknown(1) - Unknown none(2) - None imsiUnknownInHlr(3) - IMSI unknown in HLR (Home Location Register) illegalMs(4) - Illegal MS (Mobile… |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.4 | Columnc3gGsmCurrentService | read-only | current | Current service type: unknown(1) - service type is unknown invalid(2) - no service circuitSwitched(3) - circuit switched service packetSwitched(4) - packet swi… |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.5 | Columnc3gGsmPacketService | read-only | current | Packet Service type: unknown(1) - service type is unknown. none(2) - no service. gprs(3) - General Packet Radio Service (GPRS). edge(4) - Enhanced Data rates f… |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.6 | Columnc3gGsmCurrentRoamingStatus | read-only | current | This object indicates whether the modem is in the home network or is roaming. |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.7 | Columnc3gGsmNetworkSelectionMode | read-write | current | Network selection mode. Can be manual selection mode or automatic selection mode. Set to automatic by default. |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.8 | Columnc3gGsmCountry | read-only | current | Country code. Country code string is given by the base station. |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.9 | Columnc3gGsmNetwork | read-only | current | Network code. Network Code string is given by the base station. |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.10 | Columnc3gGsmMcc | read-write | current | Mobile Country Code (MCC). Value of '-1' indicates MCC is 'Not Applicable'. |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.11 | Columnc3gGsmMnc | read-write | current | Mobile Network Code (MNC). Value of '-1' indicates MNC is 'Not Applicable'. |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.12 | Columnc3gGsmRac | read-only | current | Routing Area Code (RAC). RAC is given by the base station. |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.13 | Columnc3gGsmCurrentCellId | read-only | current | Cell Identifier of current cell. Cell ID is given by the base station. |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.14 | Columnc3gGsmCurrentPrimaryScramblingCode | read-only | current | Primary scrambling code of current cell. The primary scrambling code is typically identified through symbol-by-symbol correlation over the CPICH (Common Pilot … |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.15 | Columnc3gGsmPlmnSelection | read-write | current | Public Land Mobile Network (PLMN) selection. Can be manual selection mode or automatic selection mode. Set to automatic by default. |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.16 | Columnc3gGsmRegPlmn | read-only | current | Registered PLMN. |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.17 | Columnc3gGsmPlmnAbbr | read-only | current | PLMN abbreviated number. |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.18 | Columnc3gGsmServiceProvider | read-only | current | Service provider. |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.19 | Columnc3gGsmTotalByteTransmitted | read-only | current | Total number of bytes transmitted for all calls. It is the total number of bytes transmitted by modem, not to be confused with the number of bytes transmitted … |
| 1.3.6.1.4.1.9.9.661.1.3.2.1.20 | Columnc3gGsmTotalByteReceived | read-only | current | Total number of bytes received for all calls. It is the total number of bytes received by modem, not to be confused with the number of bytes received from the … |
| 1.3.6.1.4.1.9.9.661.1.3.3 | Nodec3gGsmPdpProfile | |||
| 1.3.6.1.4.1.9.9.661.1.3.3.1 | Tablec3gGsmPdpProfileTable | not-accessible | current | Cellular GSM PDP profiles table. Cellular device contains multiple profile entries which can be used to establish cellular data connections (PDP contexts). Use… |
| 1.3.6.1.4.1.9.9.661.1.3.3.1.1 | Rowc3gGsmPdpProfileEntry | not-accessible | current | An entry (conceptual row) in the c3gGsmPdpProfileTable. |
| 1.3.6.1.4.1.9.9.661.1.3.3.1.1.1 | Columnc3gGsmPdpProfileIndex | not-accessible | current | Profile index, combined with entPhysicalIndex to access profile table. |
| 1.3.6.1.4.1.9.9.661.1.3.3.1.1.2 | Columnc3gGsmPdpProfileType | read-create | current | This object indicates configured Packet Data Protocol (PDP) type. |
| 1.3.6.1.4.1.9.9.661.1.3.3.1.1.3 | Columnc3gGsmPdpProfileAddr | read-create | current | Configured PDP/EPS Bearer address. PDP type is defined in c3gGsmPdpProfileType. |
| 1.3.6.1.4.1.9.9.661.1.3.3.1.1.4 | Columnc3gGsmPdpProfileApn | read-create | current | This object indicates profile Access Point Name (APN). This information is provided by the service provider. |
| 1.3.6.1.4.1.9.9.661.1.3.3.1.1.5 | Columnc3gGsmPdpProfileAuthenType | read-create | current | This object indicates PDP authentication type supported. CHAP and PAP are supported in GSM. The type of authentication to be used is provided by the service pr… |
| 1.3.6.1.4.1.9.9.661.1.3.3.1.1.6 | Columnc3gGsmPdpProfileUsername | read-create | current | This object indicates the username to be used for PDP authentication. This information is provided by the service provider. |
| 1.3.6.1.4.1.9.9.661.1.3.3.1.1.7 | Columnc3gGsmPdpProfilePassword | read-create | current | This object indicates the password to be used for PDP authentication. This information is provided by the service provider. |
| 1.3.6.1.4.1.9.9.661.1.3.3.1.1.8 | Columnc3gGsmPdpProfileRowStatus | read-create | current | The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table. |
| 1.3.6.1.4.1.9.9.661.1.3.3.2 | Tablec3gGsmPacketSessionTable | not-accessible | current | Cellular 3G GSM packet session table. This table is applicable in only 3G technology mode. Refer CISCO-WAN-CELL-EXT-MIB when in 4G-LTE mode. |
| 1.3.6.1.4.1.9.9.661.1.3.3.2.1 | Rowc3gGsmPacketSessionEntry | not-accessible | current | An entry (conceptual row) in the c3gGsmPacketSessionTable. |
| 1.3.6.1.4.1.9.9.661.1.3.3.2.1.1 | Columnc3gGsmPacketSessionStatus | read-only | current | This object indicates PDP session status of the profile. This is active when the call is established and PDP contextr has become active. |
| 1.3.6.1.4.1.9.9.661.1.3.3.2.1.2 | Columnc3gGsmPdpType | read-only | current | This object indicates current session PDP type. |
| 1.3.6.1.4.1.9.9.661.1.3.3.2.1.3 | Columnc3gGsmPdpAddress | read-only | current | Current session PDP context/EPS Bearer address. PDP type is obtained from c3gGsmPdpType. |
| 1.3.6.1.4.1.9.9.661.1.3.3.3 | Tablec3gGsmReqUmtsQosTable | not-accessible | current | Requested UMTS QoS parameters table. This table contains UMTS QoS parameters requested by modem to the cellular network via PDP Context Activation Request mess… |
| 1.3.6.1.4.1.9.9.661.1.3.3.3.1 | Rowc3gGsmReqUmtsQosEntry | not-accessible | current | An entry (conceptual row) in the c3gGsmReqUmtsQosTable. |
| 1.3.6.1.4.1.9.9.661.1.3.3.3.1.2 | Columnc3gGsmReqUmtsQosTrafficClass | read-create | current | Request UMTS QoS traffic classes. |
| 1.3.6.1.4.1.9.9.661.1.3.3.3.1.3 | Columnc3gGsmReqUmtsQosMaxUpLinkBitRate | read-create | current | Request UMTS QoS maximum uplink bit rate. |
| 1.3.6.1.4.1.9.9.661.1.3.3.3.1.4 | Columnc3gGsmReqUmtsQosMaxDownLinkBitRate | read-create | current | Request UMTS QoS maximum downlink bit rate. |
| 1.3.6.1.4.1.9.9.661.1.3.3.3.1.5 | Columnc3gGsmReqUmtsQosGuaUpLinkBitRate | read-create | current | Request UMTS QoS guaranteed uplink bit rate. |
| 1.3.6.1.4.1.9.9.661.1.3.3.3.1.6 | Columnc3gGsmReqUmtsQosGuaDownLinkBitRate | read-create | current | Request UMTS QoS guaranteed downlink bit rate. |
| 1.3.6.1.4.1.9.9.661.1.3.3.3.1.7 | Columnc3gGsmReqUmtsQosOrder | read-create | current | Request UMTS QoS deliver order. |
| 1.3.6.1.4.1.9.9.661.1.3.3.3.1.8 | Columnc3gGsmReqUmtsQosErroneousSdu | read-create | current | Request UMTS QoS Delivery of Erroneous SDU. |
| 1.3.6.1.4.1.9.9.661.1.3.3.3.1.9 | Columnc3gGsmReqUmtsQosMaxSduSize | read-create | current | Request UMTS QoS maximum SDU size, the valid range is between 1 and 1520 bytes. Value of '0' indicates the maximum SDU size is unspecified. |
| 1.3.6.1.4.1.9.9.661.1.3.3.3.1.10 | Columnc3gGsmReqUmtsQosSer | read-create | current | Request UMTS QoS SDU error ratio. |
| 1.3.6.1.4.1.9.9.661.1.3.3.3.1.11 | Columnc3gGsmReqUmtsQosBer | read-create | current | Request UMTS QoS residual bit error ratio. |
| 1.3.6.1.4.1.9.9.661.1.3.3.3.1.12 | Columnc3gGsmReqUmtsQosDelay | read-create | current | Request UMTS QoS transfer delay in ms, the valid range is between 1 and 4000 ms. Value of '0' indicates the QoS delay is unspecified. |
| 1.3.6.1.4.1.9.9.661.1.3.3.3.1.13 | Columnc3gGsmReqUmtsQosPriority | read-create | current | Request UMTS QoS traffic handling priority. |
| 1.3.6.1.4.1.9.9.661.1.3.3.3.1.14 | Columnc3gGsmReqUmtsQosSrcStatDescriptor | read-create | current | Request UMTS QoS source statistics descriptor. |
| 1.3.6.1.4.1.9.9.661.1.3.3.3.1.15 | Columnc3gGsmReqUmtsQosSignalIndication | read-create | current | Request UMTS QoS signalling indication. |
| 1.3.6.1.4.1.9.9.661.1.3.3.3.1.16 | Columnc3gGsmReqUmtsQosRowStatus | read-create | current | The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table. |
| 1.3.6.1.4.1.9.9.661.1.3.3.4 | Tablec3gGsmMinUmtsQosTable | not-accessible | current | Minimum acceptable UMTS QoS table. This table contains minimum acceptable UMTS QoS parameters which is checked by the MT (Mobile Termination) against the negot… |
| 1.3.6.1.4.1.9.9.661.1.3.3.4.1 | Rowc3gGsmMinUmtsQosEntry | not-accessible | current | An entry (conceptual row) in the c3gGsmMinUmtsQosTable. |
| 1.3.6.1.4.1.9.9.661.1.3.3.4.1.1 | Columnc3gGsmMinUmtsQosTrafficClass | read-create | current | Minimum UMTS QoS traffic classes. |
| 1.3.6.1.4.1.9.9.661.1.3.3.4.1.2 | Columnc3gGsmMinUmtsQosMaxUpLinkBitRate | read-create | current | Minimum UMTS QoS maximum uplink bit rate. |
| 1.3.6.1.4.1.9.9.661.1.3.3.4.1.3 | Columnc3gGsmMinUmtsQosMaxDownLinkBitRate | read-create | current | Minimum UMTS QoS maximum downlink bit rate. |
| 1.3.6.1.4.1.9.9.661.1.3.3.4.1.4 | Columnc3gGsmMinUmtsQosGuaUpLinkBitRate | read-create | current | Minimum UMTS QoS guaranteed uplink bit rate. |
| 1.3.6.1.4.1.9.9.661.1.3.3.4.1.5 | Columnc3gGsmMinUmtsQosGuaDownLinkBitRate | read-create | current | Minimum UMTS QoS guaranteed downlink bit rate. |
| 1.3.6.1.4.1.9.9.661.1.3.3.4.1.6 | Columnc3gGsmMinUmtsQosOrder | read-create | current | Minimum UMTS QoS deliver order. |
| 1.3.6.1.4.1.9.9.661.1.3.3.4.1.7 | Columnc3gGsmMinUmtsQosErroneousSdu | read-create | current | Minimum UMTS QoS Delivery of Erroneous SDU. |
| 1.3.6.1.4.1.9.9.661.1.3.3.4.1.8 | Columnc3gGsmMinUmtsQosMaxSduSize | read-create | current | Minimum UMTS maximum SDU size, the valid range is between 1 and 1520 bytes. Value of '0' indicates the maximum SDU size is unspecified. |
| 1.3.6.1.4.1.9.9.661.1.3.3.4.1.9 | Columnc3gGsmMinUmtsQosSer | read-create | current | Minimum UMTS QoS SDU error ratio. |
| 1.3.6.1.4.1.9.9.661.1.3.3.4.1.10 | Columnc3gGsmMinUmtsQosBer | read-create | current | Minimum UMTS residual bit error ratio. |
| 1.3.6.1.4.1.9.9.661.1.3.3.4.1.11 | Columnc3gGsmMinUmtsQosDelay | read-create | current | Minimum UMTS transfer delay in ms, the valid range is between 1 and 4000 ms. Value of '0' indicates the QoS delay is unspecified. |
| 1.3.6.1.4.1.9.9.661.1.3.3.4.1.12 | Columnc3gGsmMinUmtsQosPriority | read-create | current | Minimum UMTS QoS traffic handling priority. |
| 1.3.6.1.4.1.9.9.661.1.3.3.4.1.13 | Columnc3gGsmMinUmtsQosSrcStatDescriptor | read-create | current | Minimum UMTS QoS source statistics descriptor. |
| 1.3.6.1.4.1.9.9.661.1.3.3.4.1.14 | Columnc3gGsmMinUmtsQosSignalIndication | read-create | current | Minimum UMTS QoS signalling indication. |
| 1.3.6.1.4.1.9.9.661.1.3.3.4.1.15 | Columnc3gGsmMinUmtsQosRowStatus | read-create | current | The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table. |
| 1.3.6.1.4.1.9.9.661.1.3.3.5 | Tablec3gGsmNegoUmtsQosTable | not-accessible | current | Negotiated UMTS QoS table. This table contains negotiated UMTS QoS parameters returned in the Activate PDP Context Accept message. The objects in this table ar… |
| 1.3.6.1.4.1.9.9.661.1.3.3.5.1 | Rowc3gGsmNegoUmtsQosEntry | not-accessible | current | An entry (conceptual row) in the c3gGsmNegoUmtsQosTable. |
| 1.3.6.1.4.1.9.9.661.1.3.3.5.1.1 | Columnc3gGsmNegoUmtsQosTrafficClass | read-only | current | Negotiated UMTS QoS traffic classes. |
| 1.3.6.1.4.1.9.9.661.1.3.3.5.1.2 | Columnc3gGsmNegoUmtsQosMaxUpLinkBitRate | read-only | current | Negotiated UMTS QoS maximum uplink bit rate. |
| 1.3.6.1.4.1.9.9.661.1.3.3.5.1.3 | Columnc3gGsmNegoUmtsQosMaxDownLinkBitRate | read-only | current | Negotiated UMTS QoS maximum downlink bit rate. |
| 1.3.6.1.4.1.9.9.661.1.3.3.5.1.4 | Columnc3gGsmNegoUmtsQosGuaUpLinkBitRate | read-only | current | Negotiated UMTS QoS guaranteed uplink bit rate. |
| 1.3.6.1.4.1.9.9.661.1.3.3.5.1.5 | Columnc3gGsmNegoUmtsQosGuaDownLinkBitRate | read-only | current | Negotiated UMTS QoS guaranteed downlink bit rate. |
| 1.3.6.1.4.1.9.9.661.1.3.3.5.1.6 | Columnc3gGsmNegoUmtsQosOrder | read-only | current | Negotiated UMTS QoS deliver order. |
| 1.3.6.1.4.1.9.9.661.1.3.3.5.1.7 | Columnc3gGsmNegoUmtsQosErroneousSdu | read-only | current | Negotiated UMTS QoS Delivery of Erroneous SDU. |
| 1.3.6.1.4.1.9.9.661.1.3.3.5.1.8 | Columnc3gGsmNegoUmtsQosMaxSduSize | read-only | current | Negotiated UMTS QoS maximum SDU size, the valid range is between 1 and 1520 bytes. Value of '0' indicates the maximum SDU size is subscribed. |
| 1.3.6.1.4.1.9.9.661.1.3.3.5.1.9 | Columnc3gGsmNegoUmtsQosSer | read-only | current | Negotiated UMTS QoS SDU error ratio. |
| 1.3.6.1.4.1.9.9.661.1.3.3.5.1.10 | Columnc3gGsmNegoUmtsQosBer | read-only | current | Negotiated UMTS QoS residual bit error ratio. |
| 1.3.6.1.4.1.9.9.661.1.3.3.5.1.11 | Columnc3gGsmNegoUmtsQosDelay | read-only | current | Negotiated UMTS QoS transfer delay in ms, the valid range is between 1 and 4000 ms. Value of '0' indicates the QoS delay is subscribed. |
| 1.3.6.1.4.1.9.9.661.1.3.3.5.1.12 | Columnc3gGsmNegoUmtsQosPriority | read-only | current | Negotiated UMTS QoS traffic handling priority. |
| 1.3.6.1.4.1.9.9.661.1.3.3.5.1.13 | Columnc3gGsmNegoUmtsQosSrcStatDescriptor | read-only | current | Negotiated UMTS QoS source statistics descriptor. |
| 1.3.6.1.4.1.9.9.661.1.3.3.5.1.14 | Columnc3gGsmNegoUmtsQosSignalIndication | read-only | current | Negotiated UMTS QoS signalling indication. |
| 1.3.6.1.4.1.9.9.661.1.3.3.6 | Tablec3gGsmReqGprsQosTable | not-accessible | current | Requested GPRS QoS parameters table. This table contains GPRS QoS parameters requested by modem to the cellular network via PDP Context Request message. The re… |
| 1.3.6.1.4.1.9.9.661.1.3.3.6.1 | Rowc3gGsmReqGprsQosEntry | not-accessible | current | An entry (conceptual row) in the c3gGsmReqGprsQosTable. |
| 1.3.6.1.4.1.9.9.661.1.3.3.6.1.1 | Columnc3gGsmReqGprsQosPrecedence | read-create | current | Request GPRS QoS precedence. |
| 1.3.6.1.4.1.9.9.661.1.3.3.6.1.2 | Columnc3gGsmReqGprsQosDelay | read-create | current | Request GPRS QoS delay classes. |
| 1.3.6.1.4.1.9.9.661.1.3.3.6.1.3 | Columnc3gGsmReqGprsQosReliability | read-create | current | Request GPRS QoS reliability. |
| 1.3.6.1.4.1.9.9.661.1.3.3.6.1.4 | Columnc3gGsmReqGprsQosPeakRate | read-create | current | Request GPRS QoS peak rate. |
| 1.3.6.1.4.1.9.9.661.1.3.3.6.1.5 | Columnc3gGsmReqGprsQosMeanRate | read-create | current | Request GPRS QoS mean rate. |
| 1.3.6.1.4.1.9.9.661.1.3.3.6.1.6 | Columnc3gGsmReqGprsQosRowStatus | read-create | current | The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table. |
| 1.3.6.1.4.1.9.9.661.1.3.3.7 | Tablec3gGsmMinGprsQosTable | not-accessible | current | Minimum acceptable GPRS QoS table. This table contains minimum acceptable GPRS QoS parameters which is checked by the MT (Mobile Termination) against the negot… |
| 1.3.6.1.4.1.9.9.661.1.3.3.7.1 | Rowc3gGsmMinGprsQosEntry | not-accessible | current | An entry (conceptual row) in the c3gGsmMinGprsQosTable. |
| 1.3.6.1.4.1.9.9.661.1.3.3.7.1.1 | Columnc3gGsmMinGprsQosPrecedence | read-create | current | Minimum GPRS QoS precedence. |
| 1.3.6.1.4.1.9.9.661.1.3.3.7.1.2 | Columnc3gGsmMinGprsQosDelay | read-create | current | Minimum GPRS QoS delay classes. |
| 1.3.6.1.4.1.9.9.661.1.3.3.7.1.3 | Columnc3gGsmMinGprsQosReliability | read-create | current | Minimum GPRS QoS reliability. |
| 1.3.6.1.4.1.9.9.661.1.3.3.7.1.4 | Columnc3gGsmMinGprsQosPeakRate | read-create | current | Minimum GPRS QoS peak rate. |
| 1.3.6.1.4.1.9.9.661.1.3.3.7.1.5 | Columnc3gGsmMinGprsQosMeanRate | read-create | current | Minimum GPRS QoS mean rate. |
| 1.3.6.1.4.1.9.9.661.1.3.3.7.1.6 | Columnc3gGsmMinGprsQosRowStatus | read-create | current | The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table. |
| 1.3.6.1.4.1.9.9.661.1.3.3.8 | Tablec3gGsmNegoGprsQosTable | not-accessible | current | Negotiated GPRS QoS table. This table contains negotiated GPRS QoS parameters returned in the Activate PDP Context Accept message. The objects in this table ar… |
| 1.3.6.1.4.1.9.9.661.1.3.3.8.1 | Rowc3gGsmNegoGprsQosEntry | not-accessible | current | An entry (conceptual row) in the c3gGsmNegoGprsQosTable. |
| 1.3.6.1.4.1.9.9.661.1.3.3.8.1.1 | Columnc3gGsmNegoGprsQosPrecedence | read-only | current | Negotiated GPRS QoS precedence. |
| 1.3.6.1.4.1.9.9.661.1.3.3.8.1.2 | Columnc3gGsmNegoGprsQosDelay | read-only | current | Negotiated GPRS QoS delay classes. |
| 1.3.6.1.4.1.9.9.661.1.3.3.8.1.3 | Columnc3gGsmNegoGprsQosReliability | read-only | current | Negotiated GPRS QoS reliability. |
| 1.3.6.1.4.1.9.9.661.1.3.3.8.1.4 | Columnc3gGsmNegoGprsQosPeakRate | read-only | current | Negotiated GPRS QoS peak rate. |
| 1.3.6.1.4.1.9.9.661.1.3.3.8.1.5 | Columnc3gGsmNegoGprsQosMeanRate | read-only | current | Negotiated GPRS QoS mean rate. |
| 1.3.6.1.4.1.9.9.661.1.3.4 | Nodec3gGsmRadio | |||
| 1.3.6.1.4.1.9.9.661.1.3.4.1 | Tablec3gGsmRadioTable | not-accessible | current | Cellular 3G GSM/4G-LTE radio table. |
| 1.3.6.1.4.1.9.9.661.1.3.4.1.1 | Rowc3gGsmRadioEntry | not-accessible | current | An entry (conceptual row) in the c3gGsmRadioTable. |
| 1.3.6.1.4.1.9.9.661.1.3.4.1.1.1 | Columnc3gCurrentGsmRssi | read-only | current | The GPRS/UMTS/LTE RSSI value. |
| 1.3.6.1.4.1.9.9.661.1.3.4.1.1.2 | Columnc3gCurrentGsmEcIo | read-only | current | The GPRS, UMTS or LTE Ec/Io value. |
| 1.3.6.1.4.1.9.9.661.1.3.4.1.1.3 | Columnc3gGsmCurrentBand | read-only | current | GPRS/UMTS/LTE band to which the modem is attached. Refer CISCO-WAN-CELL-EXT-MIB for LTE band number when in LTE mode. |
| 1.3.6.1.4.1.9.9.661.1.3.4.1.1.4 | Columnc3gGsmChannelNumber | read-only | current | Channel number to which the modem is attached. This is only applicable in 3G technology mode. Refer CISCO-WAN-CELL-EXT-MIB for the LTE uplink and downlink chan… |
| 1.3.6.1.4.1.9.9.661.1.3.4.1.1.5 | Columnc3gGsmNumberOfNearbyCell | read-only | current | This object indicates the current total number of nearby cell in the c3gGsmNearbyCellTable. User can poll this object to get the total number of nearby cell be… |
| 1.3.6.1.4.1.9.9.661.1.3.4.2 | Tablec3gGsmNearbyCellTable | not-accessible | current | Cellular GSM/4G-LTE nearby cell table. Object c3gGsmNumberOfNearbyCell indicates the total number of nearby cell in this table. |
| 1.3.6.1.4.1.9.9.661.1.3.4.2.1 | Rowc3gGsmNearbyCellEntry | not-accessible | current | An entry (conceptual row) in the c3gGsmNearbyCellTable. |
| 1.3.6.1.4.1.9.9.661.1.3.4.2.1.1 | Columnc3gGsmNearbyCellIndex | not-accessible | current | Nearby cell index, combined with entPhysicalIndex to access the Nearby cell table c3gGsmNearbyCellTable. |
| 1.3.6.1.4.1.9.9.661.1.3.4.2.1.2 | Columnc3gGsmNearbyCellPrimaryScramblingCode | read-only | current | Nearby cell primary scrambling code. |
| 1.3.6.1.4.1.9.9.661.1.3.4.2.1.3 | Columnc3gGsmNearbyCellRscp | read-only | current | Nearby cell Received Signal Code Power (RSCP). |
| 1.3.6.1.4.1.9.9.661.1.3.4.2.1.4 | Columnc3gGsmNearbyCellEcIoMeasurement | read-only | current | Nearby cell Ec/Io measurement. |
| 1.3.6.1.4.1.9.9.661.1.3.4.3 | Tablec3gGsmHistoryTable | not-accessible | current | Cellular 3G GSM/4G-LTE RSSI history table. The history of RSSI are carried in an octet of string. Each octet in the octet string has a value from 0 to 150 and … |
| 1.3.6.1.4.1.9.9.661.1.3.4.3.1 | Rowc3gGsmHistoryEntry | not-accessible | current | An entry (conceptual row) in the c3gGsmHistoryTable. |
| 1.3.6.1.4.1.9.9.661.1.3.4.3.1.1 | Columnc3gGsmHistoryRssiPerSecond | read-only | current | Per-second RSSI history. This object contains a per-second history of RSSI values for the last 60 seconds. |
| 1.3.6.1.4.1.9.9.661.1.3.4.3.1.2 | Columnc3gGsmHistoryRssiPerMinute | read-only | current | Per-minute weakest RSSI value history. This object contains a per-minute history of weakest RSSI values for the last 60 minutes. The octet in the string is the… |
| 1.3.6.1.4.1.9.9.661.1.3.4.3.1.3 | Columnc3gGsmHistoryRssiPerHour | read-only | current | Per-hour weakest RSSI value history. This object contains a per-hour history of weakest RSSI values for the last 72 hours. The octet in the string is the weake… |
| 1.3.6.1.4.1.9.9.661.1.3.5 | Nodec3gGsmSecurity | |||
| 1.3.6.1.4.1.9.9.661.1.3.5.1 | Tablec3gGsmSecurityTable | not-accessible | current | Cellular 3G GSM/4G-LTE security table. |
| 1.3.6.1.4.1.9.9.661.1.3.5.1.1 | Rowc3gGsmSecurityEntry | not-accessible | current | An entry (conceptual row) in the c3gGsmSecurityTable. |
| 1.3.6.1.4.1.9.9.661.1.3.5.1.1.1 | Columnc3gGsmChv1 | read-write | current | Card Holder Verification 1 (CHV1), if enabled, the PIN will be verified, if disabled, the PIN will not be verified. |
| 1.3.6.1.4.1.9.9.661.1.3.5.1.1.2 | Columnc3gGsmSimStatus | read-only | current | SIM status. Indicates whether the SIM is present or removed from the SIM socket, and its current status. |
| 1.3.6.1.4.1.9.9.661.1.3.5.1.1.3 | Columnc3gGsmSimUserOperationRequired | read-only | current | If the SIM is protected (for example, because of CHV1 enabled), it will indicate the type of user operation required. |
| 1.3.6.1.4.1.9.9.661.1.3.5.1.1.4 | Columnc3gGsmNumberOfRetriesRemaining | read-only | current | Indicates the number of attempts remaining in case the SIM is locked. If the number of retries becomes zero, the SIM is blocked and becomes unusable. |
| 1.3.6.1.4.1.9.9.661.1.4 | Nodec3gWanLbs | |||
| 1.3.6.1.4.1.9.9.661.1.4.1 | Nodec3gWanLbsCommon | |||
| 1.3.6.1.4.1.9.9.661.1.4.1.1 | Tablec3gWanLbsCommonTable | not-accessible | current | This table contains information about the Cellular Location Based service feature. This GPS data is provided by the wireless modem upon GPS configuration. |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1 | Rowc3gWanLbsCommonEntry | not-accessible | current | This entry contains information about the Cellular Location Based service variables returned by the wireless modem. |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1.1 | Columnc3gLbsModeSelected | read-only | current | Mode of Location base service selected. unKnown - mode selection unkown standAlone - Standalone mode msBased - MS-Based mode msAssist - MS-Assist mode reserved… |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1.2 | Columnc3gLbsState | read-only | current | Location base service state. gpsDisabled - GPS is disabled gpsEnabled - GPS is enabled gpsLocError - GPS encounters error gpsAcquiring - GPS is acquiring fix |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1.3 | Columnc3gLbsLocFixError | read-only | current | Location base service fix error code. |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1.4 | Columnc3gLbsLatitude | read-only | current | Location base service Latitude. |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1.5 | Columnc3gLbsLongitude | read-only | current | Location base service longitude. |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1.6 | Columnc3gLbsTimeStamp | read-only | current | Location base service timestamp. |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1.7 | Columnc3gLbsLocUncertaintyAngle | read-only | current | GPS Uncertainty parameter Angle, in degrees for the Uncertainty info returned by the GPS device while doing a location fix. |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1.8 | Columnc3gLbsLocUncertaintyA | read-only | current | GPS Uncertainty parameter A, value in meters for the Uncertainty info returned by the GPS device while doing a location fix. |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1.9 | Columnc3gLbsLocUncertaintyPos | read-only | current | GPS Uncertainty parameter position, value in meters for the Uncertainty info returned by the GPS device while doing a location fix. |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1.10 | Columnc3gLbsFixtype | read-only | current | The type of location fix in Location Base service. none - default case, while LBS is not enabled. twoDimension - 2D location fix. threeDimension - 3D location … |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1.11 | Columnc3gLbsHeightValid | read-only | current | This object indicates whether the height returned by the GPS device is valid during location fix. |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1.12 | Columnc3gLbsHeight | read-only | current | This object indicates the GPS height parameter returned by the GPS device while performing location fix. |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1.13 | Columnc3gLbsLocUncertaintyVertical | read-only | current | GPS parameter vertical velocity parameter returned by the GPS device while performing location fix. |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1.14 | Columnc3gLbsVelocityValid | read-only | current | This object indicates whether the Velocity value returned by the GPS device is valid. |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1.15 | Columnc3gLbsHeading | read-only | current | The compass direction toward which the GPS receiver is (or should be) moving. |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1.16 | Columnc3gLbsVelocityHorizontal | read-only | current | Horizontal Velocity in meters per second the GPS device is heading. This is the value returned by the GPS satellite relative to the last horizontal location of… |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1.17 | Columnc3gLbsVelocityVertical | read-only | current | Vertical Velocity in meters per second the GPS device is heading. This is the value returned by the GPS satellite relative to the last vertical location of the… |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1.18 | Columnc3gLbsHepe | read-only | current | Horizontal Estimated Position Error returned by the GPS satellite for current position of the GPS device. |
| 1.3.6.1.4.1.9.9.661.1.4.1.1.1.19 | Columnc3gLbsNumSatellites | read-only | current | Number of GPS satellites in vision to the modem while GPS tracking is on. |
| 1.3.6.1.4.1.9.9.661.1.4.2 | Nodec3gWanLbsSatelliteInfo | |||
| 1.3.6.1.4.1.9.9.661.1.4.2.1 | Tablec3gWanLbsSatelliteInfoTable | not-accessible | current | This table provides information on each satellite that is visible to the modem during the location fix. These satellites guide the device to acquire a 2D or 3D… |
| 1.3.6.1.4.1.9.9.661.1.4.2.1.1 | Rowc3gWanLbsSatelliteInfoEntry | not-accessible | current | This table provides information about each satellite's elevation, azimuth, Signal to Noise ratio (SNR) and its reference number local to the router. |
| 1.3.6.1.4.1.9.9.661.1.4.2.1.1.1 | Columnc3gWanLbsSatelliteInfoIndex | not-accessible | current | An index that is assigned to each satellite under a modem and in combination with entPhysicalIndex uniquely identify it. This index is assigned arbitrarily by … |
| 1.3.6.1.4.1.9.9.661.1.4.2.1.1.2 | Columnc3gWanLbsSatelliteNumber | read-only | current | Each Satellite is assigned a unique number within this device.This object can be used to locate a particular satellite under a modem. |
| 1.3.6.1.4.1.9.9.661.1.4.2.1.1.3 | Columnc3gWanLbsSatelliteElevation | read-only | current | Angle of Elevation between the GPS antenna pointing direction, directly towards the satellite, and the local horizontal plane. It is the up-down angle |
| 1.3.6.1.4.1.9.9.661.1.4.2.1.1.4 | Columnc3gWanLbsSatelliteAzimuth | read-only | current | Azimuth of the current satellite in context referenced by the Satellite InfoIndex. Azimuth is the degree of rotation of the satellites dish on its vertical pla… |
| 1.3.6.1.4.1.9.9.661.1.4.2.1.1.5 | Columnc3gWanLbsSatelliteInfoSignalNoiseRatio | read-only | current | Signal to Noise Ratio(SNR) of received GPS signal. SNR is refered to as the signal strength in GPS standards. |
| 1.3.6.1.4.1.9.9.661.1.4.2.1.1.6 | Columnc3gWanLbsSatelliteUsed | read-only | current | Is this satellite in line of sight to the modem used in calculating the GPS location? |
| 1.3.6.1.4.1.9.9.661.1.4.2.1.1.7 | Columnc3gWanLbsSatelliteInfoRowStatus | read-create | current | The status of this conceptual row. This object is used to manage creation, modification and deletion of rows in this table. |
| 1.3.6.1.4.1.9.9.661.1.5 | Nodec3gWanSmsCommon | |||
| 1.3.6.1.4.1.9.9.661.1.5.1 | Nodec3gWanSms | |||
| 1.3.6.1.4.1.9.9.661.1.5.1.1 | Tablec3gSmsCommonTable | not-accessible | current | This table contains Cellular SMS management MIB objects. |
| 1.3.6.1.4.1.9.9.661.1.5.1.1.1 | Rowc3gSmsCommonEntry | not-accessible | current | An entry contains counters for the SMS messages received, placed, errored and archived on CDMA, GSM or LTE based modems. |
| 1.3.6.1.4.1.9.9.661.1.5.1.1.1.1 | Columnc3gSmsServiceAvailable | read-only | current | This object indicates the availability of SMS Service. |
| 1.3.6.1.4.1.9.9.661.1.5.1.1.1.2 | Columnc3gSmsOutSmsCount | read-only | current | Number of SMS messages which have been sent successfully. |
| 1.3.6.1.4.1.9.9.661.1.5.1.1.1.3 | Columnc3gSmsOutSmsErrorCount | read-only | current | Number of SMS message that could not be sent. |
| 1.3.6.1.4.1.9.9.661.1.5.1.1.1.4 | Columnc3gSmsInSmsStorageUsed | read-only | current | Number of SMS message records space used in the Incoming SMS message storage. One standard SMS message (cdma or gsm) occupies 1 unit of record storage space. A… |
| 1.3.6.1.4.1.9.9.661.1.5.1.1.1.5 | Columnc3gSmsInSmsStorageUnused | read-only | current | The number of SMS messages record space left unused in the Incoming SMS message storage. This is equal to c3gSmsInSmsStorageMax - c3gSmsInSmsStorageUsed. |
| 1.3.6.1.4.1.9.9.661.1.5.1.1.1.6 | Columnc3gSmsInSmsArchiveCount | read-only | current | Number of successful archive of Incoming SMS messages since router reload. Each SMS message occupies x bytes of space. So if the incoming message is huge, then… |
| 1.3.6.1.4.1.9.9.661.1.5.1.1.1.7 | Columnc3gSmsInSmsArchiveErrorCount | read-only | current | The number of Incoming SMS messages that could not be archived since device was reloaded. |
| 1.3.6.1.4.1.9.9.661.1.5.1.1.1.8 | Columnc3gSmsArchiveUrl | read-only | current | URL of the sms archive directory on the ftp server. The url will be of this format ftp://x.y.z.k/user/dirname |
| 1.3.6.1.4.1.9.9.661.1.5.1.1.1.9 | Columnc3gSmsOutSmsStatus | read-only | current | Status of the last send operation of outgoing SMS message to the network. |
| 1.3.6.1.4.1.9.9.661.1.5.1.1.1.10 | Columnc3gSmsInSmsCount | read-only | current | Number of SMS messages which have been received successfully and stored in router. These SMS's are a mirror copy of SMS stored in Modem or SIM |
| 1.3.6.1.4.1.9.9.661.1.5.1.1.1.11 | Columnc3gSmsInSmsDeleted | read-only | current | Number of SMS messages which have been deleted since router boot up. This does not include SMS messages that are already archived. |
| 1.3.6.1.4.1.9.9.661.1.5.1.1.1.12 | Columnc3gSmsInSmsStorageMax | read-only | current | Number of SMS message records space allocated in the router's DRAM to store Incoming SMS messages. |
| 1.3.6.1.4.1.9.9.661.1.5.1.1.1.13 | Columnc3gSmsInSmsCallBack | read-only | current | Number of incoming SMS messages that triggered callback. |
| 1.3.6.1.4.1.9.9.661.1.5.1.1.1.14 | Columnc3gSmsOutSmsPendingCount | read-only | current | Number of outgoing SMS messages that are in pending queue of the router. |
| 1.3.6.1.4.1.9.9.661.1.5.1.1.1.15 | Columnc3gSmsOutSmsArchiveCount | read-only | current | Number of successfull archive of outgoing SMS messages since router reload. |
| 1.3.6.1.4.1.9.9.661.1.5.1.1.1.16 | Columnc3gSmsOutSmsArchiveErrorCount | read-only | current | Number of failed archive of outgoing SMS messages since router reload. |
| 1.3.6.1.4.1.9.9.661.1.5.1.1.1.17 | Columnc3gSmsInSmsArchived | read-only | current | Number of Incoming SMS messages that are successfully archived since router reload. |
| 1.3.6.1.4.1.9.9.661.2 | NodeciscoWan3gMIBConform | |||
| 1.3.6.1.4.1.9.9.661.2.1 | NodeciscoWan3gMIBCompliances | |||
| 1.3.6.1.4.1.9.9.661.2.1.1 | ComplianceciscoWan3gMIBCompliance | deprecated | This is a default module-compliance containing default object groups. | |
| 1.3.6.1.4.1.9.9.661.2.1.2 | ComplianceciscoWan3gMIBCompliance1 | deprecated | The compliance statement for the CISCO-WAN-3G-MIB. | |
| 1.3.6.1.4.1.9.9.661.2.1.3 | ComplianceciscoWan3gMIBComplianceRev1 | current | This is a default module-compliance containing default object groups. | |
| 1.3.6.1.4.1.9.9.661.2.1.4 | ComplianceciscoWan3gMIBCompliance1Rev1 | current | The compliance statement for the CISCO-WAN-3G-MIB. | |
| 1.3.6.1.4.1.9.9.661.2.2 | NodeciscoWan3gMIBGroups | |||
| 1.3.6.1.4.1.9.9.661.2.2.1 | GroupciscoWan3gMIBCommonObjectGroup | current | A collection of common objects for Cellular interface. | |
| 1.3.6.1.4.1.9.9.661.2.2.2 | GroupciscoWan3gMIBCdmaObjectGroup | current | A collection of objects for Cellular 3G CDMA. | |
| 1.3.6.1.4.1.9.9.661.2.2.3 | GroupciscoWan3gMIBGsmObjectGroup | current | A collection of objects for Cellular 3G GSM and LTE. | |
| 1.3.6.1.4.1.9.9.661.2.2.4 | GroupciscoWan3gMIBNotificationGroup | deprecated | A collection of objects for Cellular WAN notifications. ciscoWan3gMIBNotificationGroup object is superseded by ciscoWan3gMIBNotificationGroupRev1. | |
| 1.3.6.1.4.1.9.9.661.2.2.5 | GroupciscoWan3gMIBLbsObjectGroup | current | A collection of common objects for Cellular Location Based Service. | |
| 1.3.6.1.4.1.9.9.661.2.2.6 | GroupciscoWan3gMIBSmsObjectGroup | current | A collection of common objects for Cellular Short Messaging Service. | |
| 1.3.6.1.4.1.9.9.661.2.2.7 | GroupciscoWan3gMIBNotificationGroupRev1 | current | A collection of objects for Cellular WAN notifications. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| C3gEcIo | Integer32 (-150..0) | current | Generic EcIo range. |
| C3gGprsQosDelay | INTEGER { subscription(1), delayClass1(2), delayClass2(3), delayClass3(4), delayClass4(5) } | current | GPRS QoS delay classes: subscription(1) - based on user's subscription delayClass1(2) - delay class 1 delayClass2(3) - delay class 2 delayClass3(4) - delay class 3 delayClass4(5) - delay class 4 |
| C3gGprsQosMeanRate | INTEGER { subscription(1), rate100(2), rate200(3), rate500(4), rate1k(5), rate2k(6), rate5k(7), rate10k(8), rate20k(9), rate50k(10), rate100k(11), rate200k(12), rate500k(13), rate1m(14), rate2m(15), rate5m(16), rate10m(17), rate20m(18), rate50m(19), resv1(20), resv2(21), resv3(22), resv4(23), resv5(24), resv6(25), resv7(26), resv8(27), resv9(28), resv10(29), resv11(30), resv12(31), bestEffort(32) } | current | GPRS QoS mean rate: subscription(1) - based on user's subscription rate100(2) - 100 octet/hour rate200(3) - 200 octet/hour rate500(4) - 500 octet/hour rate1k(5) - 1000 octet/hour rate2k(6) - 2000 octet/hour rate5k(7) - … |
| C3gGprsQosPeakRate | INTEGER { subscription(1), upTo1kops(2), upTo2kops(3), upTo4kops(4), upTo8kops(5), upTo16kops(6), upTo32kops(7), upTo64kops(8), upTo128kops(9), upTo256kops(10) } | current | GPRS QoS peak rate: subscription(1) - based on user's subscription upTo1kops(2) - up to 1000 octet/second upTo2kops(3) - up to 2000 octet/second upTo4kops(4) - up to 4000 octet/second upTo8kops(5) - up to 8000 octet/sec… |
| C3gGprsQosPrecedence | INTEGER { subscription(1), highPriority(2), normalPriority(3), lowPriority(4) } | current | GPRS QoS precedence: subscription(1) - based on user's subscription highPriority(2) - high priority normalPriority(3) - normal priority lowPriority(4) - low priority |
| C3gGprsQosReliability | INTEGER { subscription(1), ackGtpLlcRlcProtData(2), unAckGtpAckLlcRlcProtData(3), unAckGtpLlcAckRlcProtData(4), unAckGtpLlcRlcProtData(5), unAckGtpLlcRlcUnProtData(6) } | current | GPRS QoS reliability: subscription(1) - based on user's subscription ackGtpLlcRlcProtData(2) - acknowledged GTP, LLC, and RLC; protected data unAckGtpAckLlcRlcProtData(3) - unacknowledged GTP, acknowledged LLC and RLC; … |
| C3gPdpType | INTEGER { unknown(1), ipV4(2), ppp(3), ipV6(4), ipV4V6(5) } | current | Generic PDP type. |
| C3gRssi | Integer32 (-150..0) | current | Generic RSSI range. |
| C3gServiceCapability | BITS { oneXRtt(0), evDoRel0(1), evDoRelA(2), evDoRelB(3), gprs(4), edge(5), umtsWcdma(6), hsdpa(7), hsupa(8), hspa(9), hspaPlus(10), lteTdd(11), lteFdd(12) } | current | 3G service capability: oneXRtt(0) - 1xRTT evDoRel0(1) - EVDO Revision 0 evDoRelA(2) - EVDO Revision A evDoRelB(3) - EVDO Revision B gprs(4) - GPRS edge(5) - EDGE umtsWcdma(6) - UMTS/WCDMA hsdpa(7) - HSDPA hsupa(8) - HSU… |
| C3gTemperature | Integer32 (-50..100) | current | Generic temperature range. |
| C3gUmtsQosBer | INTEGER { subscription(1), fiveExpMinus2(2), oneExpMinus2(3), fiveExpMinus3(4), fourExpMinus3(5), oneExpMinus3(6), oneExpMinus4(7), oneExpMinus5(8), oneExpMinus6(9), sixExpMinus8(10) } | current | UMTS QoS residual bit error ratio (BER): subscription(1) - based on user's subscription fiveExpMinus2(2) - 5E-2 oneExpMinus2(3) - 1E-2 fiveExpMinus3(4) - 5E-3 fourExpMinus3(5) - 4E-3 oneExpMinus3(6) - 1E-3 oneExpMinus4(… |
| C3gUmtsQosErroneousSdu | INTEGER { subscription(1), noDetect(2), errSduDeliver(3), errSduNotDeliver(4) } | current | UMTS QoS Delivery of Erroneous Service Data Unit(SDU): subscription(1) - based on user's subscription noDetect(2) - no detect errSduDeliver(3) - erroneous SDUs are delivered errSduNotDeliver(4) - erroneous SDUs are not … |
| C3gUmtsQosLinkBitRate | INTEGER { subscription(1), rate16kbps(2), rate32kbps(3), rate64kbps(4), rate128kbps(5), rate256kbps(6), rate384kbps(7), rate1dot8mbps(8), rate3dot6mbps(9), rate7dot2mbps(10), rate14dot4mbps(11), rate56kbps(12), rate1dot15mbps(13), rate1dot6mbps(14), rate2dot1mbps(15), rate2dot8mbps(16), rate4dot2mbps(17), rate8dot4mbps(18) } | current | UMTS QoS link bit rate: subscription(1) - based on user's subscription rate16kbps(2) - 16 Kbps rate32kbps(3) - 32 Kbps rate64kbps(4) - 64 Kbps rate128kbps(5) - 128 Kbps rate256kbps(6) - 256 Kbps rate384kbps(7) - 384 Kbp… |
| C3gUmtsQosOrder | INTEGER { subscription(1), withDeliverOrder(2), withoutDeliverOrder(3) } | current | UMTS QoS delivery order: subscription(1) - based on user's subscription withDeliverOrder(2) - with delivery order withoutDeliverOrder(3) - without delivery order |
| C3gUmtsQosPriority | INTEGER { subscription(1), level1(2), level2(3), level3(4) } | current | UMTS QoS traffic handling priority: subscription(1) - based on user's subscription level1(2) - priority level 1 level2(3) - priority level 2 level3(4) - priority level 3 |
| C3gUmtsQosSer | INTEGER { subscription(1), oneExpMinus2(2), sevenExpMinus3(3), oneExpMinus3(4), oneExpMinus4(5), oneExpMinus5(6), oneExpMinus6(7), oneExpMinus1(8) } | current | UMTS QoS SDU error ratio: subscription(1) - based on user's subscription oneExpMinus2(2) - 1E-2 sevenExpMinus3(3) - 7E-3 oneExpMinus3(4) - 1E-3 oneExpMinus4(5) - 1E-4 oneExpMinus5(6) - 1E-5 oneExpMinus6(7) - 1E-6 oneExp… |
| C3gUmtsQosSignalIndication | INTEGER { notOptimized(1), optimized(2) } | current | UMTS QoS signalling indication: notOptimized(1) - not optimized for signalling traffic optimized(2) - optimized for signalling traffic |
| C3gUmtsQosSrcStatDescriptor | INTEGER { unknown(1), speech(2) } | current | UMTS QoS source statistics descriptor: unknown(1) - unknown speech(2) - speech |
| C3gUmtsQosTrafficClass | INTEGER { subscription(1), conversational(2), streaming(3), interactive(4), background(5) } | current | UMTS QoS traffic classes: subscription(1) - based on user's subscription conversational(2) - conversational streaming(3) - streaming interactive(4) - interactive background(5) - background |