CISCO-WAN-BBIF-ATM-CONN-MIB
72 objects
The MIB module to configure the ATM Connections on a broad band interface in PXM1 Service module.
Imported Objects
| BASIS-MIB | bbChanCnfGrp bbChanStateGrp |
| CISCOWAN-SMI | ciscoWan |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | DisplayString TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.351.110.5.2.7.1.1 | TablebbChanCnfGrpTable | not-accessible | current | The Broadband Channel config table is for a channel on logical interface. There will an entry for each of the channel added on the logical partition of the phy… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1 | RowbbChanCnfGrpEntry | not-accessible | current | The config table is for logical channel. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.1 | ColumnbbChanCnfNum | read-only | current | This identifies a channel on the PXM logical interface, used as PXM port. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.2 | ColumnbbChanRowStatus | read-write | current | This object is used for adding/deleting/modifying entries in the table. add(1) : Adds the entry. delete(2) : Deletes the entry modify(3) : Set this before modi… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.3 | ColumnbbChanConnType | read-write | current | This specifies the connection type vpc(1) : Virtual Path Connection vcc(2) : Virtual Channel Connection This object can not be modified once the connection is … |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.4 | ColumnbbChanServiceType | read-write | current | This specifies the service type cbr(1) : Constant Bit Rate vbr(2) : Variable Bit Rate abr(3) : Available Bit Rate ubr(4) : Unspecified Bit Rate vbr-rt(5): Vari… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.5 | ColumnbbChanConnDesc | read-write | current | A string that has been defined to give a descriptive name to the connection. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.6 | ColumnbbChanSvcFlag | read-write | current | This specifies the connection type svc(1) : SVC connection pvc(2) : PVC connection, used by PAR(Portable Auto Route) spvc(3) : Soft PVC connection, used by PNNI |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.7 | ColumnbbChanSvcConnId | read-write | current | This connection ID is for future use Currently not supported. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.8 | ColumnbbChanIfNum | read-write | current | Channel's logical Interface from which traffic of the connection will be received. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.9 | ColumnbbChanVpi | read-write | current | VPI for the connection. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.10 | ColumnbbChanVci | read-write | current | VCI for the connection. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.11 | ColumnbbChanUpcEnable | read-write | current | enables/disables UPC for Ingress cells. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.12 | ColumnbbChanUpcPCR | read-write | current | PCR(0+1), Peak Cell Rate, specifies an upper bound on rate at which traffic can be submitted on an ATM connection. This object applies to the First Leaky Bucke… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.13 | ColumnbbChanUpcCDVT | read-write | current | Compliant Cell Delay Variation. Also known as CDVT(0+1), Cell Delay Variation Tolerance, which specifies the maximum time period for accumulated violations of … |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.14 | ColumnbbChanUpcSCR | read-write | current | SCR, Sustainable Cell Rate, is an upper bound on the conforming average rate of an ATM connection, over time scales which are long relative to those for which … |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.15 | ColumnbbChanUpcMBS | read-write | current | Maximum Burst Size (MBS). Also known as Compliant Burst Size (CBS). . Units: cells . Applicable connection types: . VBR, ABR . Default: 1000 . Range : 1-5000000 |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.16 | ColumnbbChanGcra1Action | read-write | current | GCRA1 Action. 1 = No Action 2 = Tag Untagged cells 3 = Tag untagged cells and discard tagged cells 4 = Discard all (0+1) non-comforming cells. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.17 | ColumnbbChanGcra2Action | read-write | current | GCRA2 Action. 1 = No Action 2 = Tag Untagged cells 3 = Tag untagged cells and discard tagged cells 4 = Discard all (0+1) non-comforming cells. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.18 | ColumnbbChanUpcSCRPolicing | read-write | current | Selects SCR policing for CLP = 0 or all cells. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.19 | ColumnbbChanEfciThreshold | read-write | current | Threshold above which EFCI bit is to be set. Default Value is 3/4 of max cell count. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.20 | ColumnbbChanDiscardOption | read-write | current | Enable Frame Discard or CLP Hysteresis. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.21 | ColumnbbChanFrmDiscardThreshold | read-write | current | Ingress Frame Discard Threshold. Valid only when Ingress Frame Discard option is selected. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.22 | ColumnbbChanClpHiThreshold | read-write | current | Ingress CLP High Threshold. Default is 3/4 of max cell count. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.23 | ColumnbbChanClpLoThreshold | read-write | current | Ingress CLP Low Threshold. Valid only when Ingress CLP Hysteresis option is selected. Default Value is 1/2 of max cell count. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.24 | ColumnbbChanCongstUpdateCode | read-write | current | Ingress Channel Congestion Update Code. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.25 | ColumnbbChanMaxCellMemThreshold | read-write | current | Maximum number of cells of that connection in the memory. Assuming Total Cell Memory is 512K cells, this is defaulted to half of total size. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.26 | ColumnbbChanIngrPercentUtil | read-write | current | Percentage Utilization of the IngrService Rate. This is used for connection admission control. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.27 | ColumnbbChanEgrPercentUtil | read-write | current | Percentage Utilization of the EgrService Rate. This is used for egress bandwidth calculation and connection admission control. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.28 | ColumnbbChanEgrSrvRate | read-write | current | Egress service rate - This is used for egress bandwidth calculation and for connection admission control. The actual value depends on the speed of the logical … |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.29 | ColumnbbChanOvrSubOvrRide | read-write | current | Channel Over Subscrive Override This MIB variable allows one to add a new connection on a port even if it is over subscribed. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.30 | ColumnbbChanLocalVpi | read-only | current | The VPI value for this channel. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.31 | ColumnbbChanLocalVci | read-only | current | The VCI value for this channel. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.32 | ColumnbbChanLocalNsapAddr | read-write | current | The Near End NSAP Address value for this channel. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.33 | ColumnbbChanRemoteVpi | read-write | current | The VPI value for this channel. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.34 | ColumnbbChanRemoteVci | read-write | current | The VCI value for this channel. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.35 | ColumnbbChanRemoteNsapAddr | read-write | current | The Far End NSAP Address value for this channel. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.36 | ColumnbbChanMaster | read-write | current | This is used by the PXM switch platform module, to determine if this endpoint ia master or slave. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.37 | ColumnbbChanRtePriority | read-write | current | This is also known as class of service, it is used by PXM to determine how important this connection is when selecting connections to route. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.38 | ColumnbbChanMaxCost | read-write | current | Maximum allowed cost. It is related to Cost Based Routing. This is used by PXM so that it won't choose a path with a cost greater than this configured level. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.39 | ColumnbbChanRestrictTrkType | read-write | current | Restricted trunk type for routind, used by PXM. It specifies that the connection either cannot be routed over satellite trunks or terrestrial trunks, or it can… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.40 | ColumnbbChanTestType | read-write | current | The chanTestType starts testing the continuity or delay of a connection. It sends specific cell patterns toward the network and the terminating end of this con… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.41 | ColumnbbChanTestState | read-only | current | This object provides the state of the test performed on a connection. When you add a connection then the chanTestState becomes notinprogress and when you selec… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.42 | ColumnbbChanTestResult | read-only | current | This is round trip delay in milliseconds. When you select testdelay option for the chanTestType, the result of the test that is measured in milliseconds can be… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.43 | ColumnbbChanTestTypeCPESide | read-write | current | The chanTestType starts testing the segment continuity of a connection. It sends OAM Segment loopback cell towards port side (CPE) The CPE would loop back the … |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.44 | ColumnbbChanTestStateCPESide | read-only | current | This shows the state of the test When you add a connection then the chanTestState becomes notinprogress and when you select any test, it would go to inprogress… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.45 | ColumnbbConnVpcFlag | read-write | current | This represents the connection type, used for PXM to identify VPC/VCC. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.46 | ColumnbbConnServiceType | read-write | current | This specifies the service type 1 ==> Constant Bit Rate 2 ==> Variable Bit Rate 4 ==> Unspecified Bit Rate 6 ==> Available Bit Rate ( standard ) 8 ==> Variable… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.47 | ColumnbbConnPCR | read-write | current | Peak cell rate, could be derived from the end point parameter |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.48 | ColumnbbConnSCR | read-write | current | Sustained cell rate, could be derived from the end point parameter |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.49 | ColumnbbConnPercentUtil | read-write | current | This is the expected long-term utilization of the channel by this end-point. |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.50 | ColumnbbRemoteConnPCR | read-write | current | Peak cell rate of the other end, if not set, will be set to the same as local end PCR (bbChanUpcPCR). However, note that if the PCRs for both local and remote … |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.51 | ColumnbbRemoteConnSCR | read-write | current | Sustained cell rate of the other end, if not set, will be set to the same as local end SCR (bbChanUpcSCR). However, note that if the PCRs for both local and re… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.52 | ColumnbbRemoteConnPercentUtil | read-write | current | This is the expected long-term utilization of the channel by this end-point. If this is not specified in the connection setup request, it'll be defaulted to 10… |
| 1.3.6.1.4.1.351.110.5.2.7.1.1.1.53 | ColumnbbChanUpcMCR | read-write | current | SCR, Sustainable Cell Rate, is an upper bound on the conforming average rate of an ATM connection, over time scales which are long relative to those for which … |
| 1.3.6.1.4.1.351.110.5.2.7.1.2 | ScalarbbChanNumNextAvailable | read-only | current | This variable contains the next unused channel number of the possible 4096 . This number can be used in channel config table. ChanNumNextAvailable gets updated… |
| 1.3.6.1.4.1.351.110.5.2.7.1.3 | ScalarbbChanVpIdNextAvailable | read-only | current | This in only valid for a Service Module, will NOT be used in PXM. This variable contains the next unused local VPId of the possible 1 to 4095. This number can … |
| 1.3.6.1.4.1.351.110.5.2.7.2.1 | TablebbChanStateGrpTable | not-accessible | current | The Broadband Channel state table is for a channel on logical interface. There will an entry for each of the channel added on the logical partition of the phys… |
| 1.3.6.1.4.1.351.110.5.2.7.2.1.1 | RowbbChanStateGrpEntry | not-accessible | current | The state table is for logical channel. The available number of channels on the broadband interface (user ports) on the PXM card is restricted to 4K. The PXM c… |
| 1.3.6.1.4.1.351.110.5.2.7.2.1.1.1 | ColumnbbChanStateNum | read-only | current | Refers to the logical channel number. |
| 1.3.6.1.4.1.351.110.5.2.7.2.1.1.2 | ColumnbbChanState | read-only | current | This variable indicates the state of the VC (channel). |
| 1.3.6.1.4.1.351.110.5.2.7.2.1.1.3 | ColumnbbChanEgrXmtState | read-only | current | Indicates the status of port transmit(Egress). |
| 1.3.6.1.4.1.351.110.5.2.7.2.1.1.4 | ColumnbbChanIngrRcvState | read-only | current | indicates the status of port receive(Ingress). |
| 1.3.6.1.4.1.351.150.35 | IdentityciscoWanBbifAtmConnMIB | The MIB module to configure the ATM Connections on a broad band interface in PXM1 Service module. | ||
| 1.3.6.1.4.1.351.150.35.2 | NodecwbAtmConnMIBConformance | |||
| 1.3.6.1.4.1.351.150.35.2.1 | NodecwbAtmConnMIBGroups | |||
| 1.3.6.1.4.1.351.150.35.2.1.1 | GroupcwbAtmConnGroup | current | A collection of objects providing information applicable to an ATM Connection on broad band interfaces. | |
| 1.3.6.1.4.1.351.150.35.2.1.2 | GroupcwbAtmConnStateGroup | current | A collection of objects related to state of ATM Connections on Broad band interface. | |
| 1.3.6.1.4.1.351.150.35.2.1.3 | GroupcwbAtmConnGeneralGroup | current | A collection of objects related to next available channeli number and next available VPI value of connections supported. | |
| 1.3.6.1.4.1.351.150.35.2.2 | NodecwbAtmConnMIBCompliances | |||
| 1.3.6.1.4.1.351.150.35.2.2.1 | CompliancecwbAtmConnCompliance | current | The compliance statement for SNMP entities which support Frame realy connection MIB. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| IfNsapAddress | OCTET STRING (SIZE(20)) | current | ATM address used by the networking entity. The only address type presently supported is NSAP (20 octets) |