CISCO-WAN-FR-CONN-MIB
120 objects
The MIB module to configure the Frame Relay connection configuration. Terminologies Used: SIW - Frame-Relay-to ATM Service Interworking. In SIW, the ATM port connected to a frame relay port does not need to be aware that it is connected to an interworking function. This is explained in document FRF.8. NIW - Frame-Relay-to ATM Network Interworking. In NIW, the ATM port connected to a frame relay port does need to be aware that it is connected to an interworking function. PVC - Permanent Virtual Circuit OR Permanent Virtual Connection A frame relay logical link, whose endpoints and class of service are defined by network management. A PVC consists of the originating frame relay network element address, originating DLCI, terminating frame relay network element address and terminating DLCI. This is controlled by PAR(Portable Auto Route) controller. SPVC - Soft Permanent Virtual Circuits. This is a PVC controlled by PNNI Controller. Frame Relay PVC/SPVC end-point/Channel is referred to as frame Relay connection in this MIB. Traffic shaping parameters: CIR, EIR, Bc, Be, DE, Tc, AR corresponding to rate of the physical interface. CIR - Committed Information Rate. This is the rate of traffic that the PVC will support as 'comitted' traffic. The committed rate(in bits per second) at which the ingress access interface trunk interfaces, and egress access interface of a frame relay network transfer information to the destination frame relay end system under normal conditions. The rate is averaged over a minimum time interval Tc. AR - Access Rate The maximum number of bits per second that an end station can transmit into the network is bounded by the acess rate of the user-network interface. The line speed of the user network connection limits the access rate. Bc - Committed Burst Size The maximum amount of data(in bits) that the network agrees to transfer, under normal conditions during a time interval Tc. The data is in bytes in the current implementation. Be - Excess Burst Size The maximum amount of uncommitted data(in bits) in excess of BC that a frame relay network can attempt to deliver during a time interval Tc. This data generally is delivered with a low probability than Bc. The network treats Be data as discard eligible. The data is in bytes in the current implementation. Tc - The committed rate measurement interval. The time interval during which the user can send only BC committed amount of data and BE excess amount of data. EIR - Excess Information Rate This is the bandwidth in excess of CIR the PVC will be allowed to burst on a a given PVC. The average rate at which excess traffic is to be policed. This number is computed based on Bc, Be, CIR and Tc. DE - Discard Eligibility Frame Forwarding Port: Frame Forwarding Ports are identified by portType = frame-forward(3). NOTE: The objects related to frame relay ports are available in ifTable,if ifTable is implemented in service module/card. Following Service Modules support ifTable: FRSM-12
Imported Objects
| BASIS-MIB | frameRelay frChan |
| CISCOWAN-SMI | ciscoWan |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.351.110.5.1.2.1 | NodefrChanCnfGrp | |||
| 1.3.6.1.4.1.351.110.5.1.2.1.1 | TablefrChanCnfGrpTable | not-accessible | current | This table is for configuring connection parameters for frame relay connections. |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1 | RowfrChanCnfGrpEntry | not-accessible | current | An entry for each frame relay connection. |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.1 | ColumnchanNum | read-only | current | The value of this object identifies the frame relay connection/channel index. Note that the actual range of the index supported by a card depends on the type o… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.2 | ColumnchanRowStatus | read-write | current | This object is used for adding/modifying/deleting the channel. add(1) : For adding the frame relay connections. delete(2): For deleting frame relay connections… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.3 | ColumnchanPortNum | read-write | current | This object refers to the frame relay port on which channel is created. This is a mandatory object for creating the channel. For FRSM12 Card: This object conta… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.4 | ColumndLCI | read-write | current | The value of this object is the DLCI number of the channel. This is a mandatory object for creating the channel. All the connections on the same port should ha… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.5 | ColumnegressQSelect | read-write | current | Selects one out of two possible port queues. The default port queue number is 1 which is the high pririty queue. 1 = High priority queue 2 = Low priority queue… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.6 | ColumningressQDepth | read-write | current | This variable sets the max depth for queue, before it starts dropping the cells. It is defined in terms of number of bytes. In all cards except the FRSM-VHS ca… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.7 | ColumningressQECNThresh | read-write | current | This variable sets the max depth for queue, before it starts flow control. It is defined in terms of number of bytes. In all cards except the FRSM-VHS card, th… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.8 | ColumningressQDEThresh | read-write | current | This variable sets the max depth for queue, before they become discard eligible. It is defined in terms of number of bytes. In all cards except the FRSM-VHS ca… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.9 | ColumnegressQDepth | read-write | current | This variable sets the max depth for queue, before it starts dropping the cells. It is defined in terms of number of bytes. In all cards except the FRSM-VHS ca… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.10 | ColumnegressQDEThresh | read-write | current | This variable sets the max depth for queue, before they become discard eligible. It is defined in terms of number of bytes. In all cards except the FRSM-VHS ca… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.11 | ColumnegressQECNThresh | read-write | current | This variable sets the max depth for queue, before it starts flow control. It is defined in terms of number of bytes. In all cards except the FRSM-VHS card, th… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.12 | ColumndeTaggingEnable | read-write | current | This object enables/disables the DE tagging. The tagging is enabled only in the ingress direction. For FRSM12 Card: When this object is disabled, the ingress p… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.13 | Columncir | read-write | current | The value of this object is equal to the CIR parameter for this frame relay connection. The CIR value have to be less than or equal to the port speed. Any valu… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.14 | Columnbc | read-write | current | The value of this object is equal to the committed burst size(BC) parameter for this PVC endpoint. The value of bc can not be 0 when cir is non zero. The value… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.15 | Columnbe | read-write | current | The value of this object is euqal to the excess burst size(Be) parameter for this PVC endpoint. The value be can not be 0 when cir is 0. The peak value for be … |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.16 | Columnibs | read-write | current | The value of this object is euqal to the excess burst size(Be) parameter for this PVC endpoint. The value of ibs should be less or equal to bc when cir is grea… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.17 | ColumnforeSightEnable | read-write | current | This variable enables/disables foreSight option. Following objects can be modified only when this object is set to enable(1): qir, mir, pir The RATE CONTROL FE… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.18 | Columnqir | read-write | current | The value of this object is euqal to the quiescent information rate for Foresight. The unit is 1 Cell/Sec = 16 fastpackets/sec. Following information about cps… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.19 | Columnmir | read-write | current | The value of this object is euqal to the minimum information rate for Foresight. The unit is 1 Cell/Sec = 16 fastpackets/sec. is equal to 16 fastpackets/sec. F… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.20 | Columnpir | read-write | current | The value of this object is euqal to the peak information rate for Foresight. The unit is 1 Cell/Sec = 16 fastpackets/sec. is equal to 16 fastpackets/sec. Foll… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.21 | ColumnchanLocRmtLpbkState | read-write | current | This variable enables or disables the remote loopback for each channel. When you enable this option on a connection (channel) then all the cells that are comin… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.22 | ColumnchanTestType | read-write | current | The chanTestType starts testing the continuity or delay of a connection. It sends specific cell patterns toward the network and the terminating end of this con… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.23 | ColumnchanTestState | read-only | current | This shows the state of the test When you add a connection then the chanTestState becomes notinprogress and when you select any test, it would go to inprogress… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.24 | ColumnchanRTDResult | read-only | current | This is round trip delay in milliseconds. When you select testdelay option for the chanTestType, the result of the test that is measured in milliseconds can be… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.25 | ColumnchanType | read-write | current | The value of this object is used for setting the channel type of a frame relay connection. If set with values frSIW-transparent(2) and frSIW-translate(3), all … |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.26 | ColumnchanFECNconfig | read-write | current | The value of this object specifies how to map from FECN field in the frame Relay PDU to the EFCI field in the ATM cells. This object does not apply to NIW. Thi… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.27 | ColumnchanDEtoCLPmap | read-write | current | The value of this object specifies how to map from DE bit on the Frame Relay side to CLP bit on the ATM side. mapCLP(1) : Map DE bit to CLP bit in ATM cell. se… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.28 | ColumnchanCLPtoDEmap | read-write | current | The value of this object enables mapping of Cell Loss Priority(CLP) bit on the ATM Side to Discard Eligibility(DE) bit on the Frame relay side. The possible va… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.29 | ColumnchanIngrPercentUtil | read-write | current | The ingress utilization on a frame relay connection. |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.30 | ColumnchanEgrPercentUtil | read-write | current | The egress utilization on a frame relay connection. |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.31 | ColumnchanEgrSrvRate | read-write | current | The value of this object identifies egress CIR value for a frame relay connection. The value of this object must be less than or equal(<=) to the port speed. T… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.32 | ColumnchanOvrSubOvrRide | read-write | current | The value of this object enables/disables the oversubscription on a connection. This object allows one to add a new connection on a port even if it is over sub… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.33 | ColumnchanFrConnType | read-write | current | The value of this object is used for configuring connection type of a frame relay connection. The possible values are : pvc(1) : Permanent Virtual Connection s… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.34 | ColumnfrCDRNumber | read-write | current | The value of this object identifies the CDR(Call Detail Record) number. This is the key to correlate cell/frame counts, start/end record. For FRSM12 Card: Not … |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.35 | ColumnfrLocalVpi | read-only | current | The value of this object provides the VPI value for the local endpoint. This object in conjunction with frLocalVci and frLocalNSAP represents the local end poi… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.36 | ColumnfrLocalVci | read-only | current | The value of this object provides the VCI value for the local endpoint. This object in conjunction with frLocalVpi and frLocalNSAP represents the local end poi… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.37 | ColumnfrLocalNSAP | read-write | current | The value of this object identifies the NSAP address of the frame relay connection. The value of this object follows the format: Prefix : 13 Bytes Cisco ID : 2… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.38 | ColumnfrRemoteVpi | read-write | current | The value of this object identifies the VPI value of remote end point of this connection. The frRemoteVpi, frRemoteVci and frRemoteNSAP identifies the remote e… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.39 | ColumnfrRemoteVci | read-write | current | The value of this object identifies the VCI value of remote end point of this connection. The frRemoteVpi, frRemoteVci and frRemoteNSAP identifies the remote e… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.40 | ColumnfrRemoteNSAP | read-write | current | The value of this object identifies the NSAP address of the frame relay connection. The value of this object follows the format: Prefix : 13 Bytes Cisco ID : 2… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.41 | ColumnfrMastership | read-write | current | This is used by PXM to determine if this end point is master or slave, a new type unknown is added to identify the SM in MGX8220 shelf and the SM in MGX shelf.… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.42 | ColumnfrVpcFlag | read-write | current | This represents the connection type, used for PXM to identify VPC/VCC but FRSM card doesn't use it always set to vcc for FRSM card For FRSM12 Card: For chanFrC… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.43 | ColumnfrConnServiceType | read-write | current | This specifies the service type 1 ==> Constant Bit Rate 2 ==> Variable Bit Rate 3 ==> Not used 4 ==> Unspecified Bit Rate 5 ==> ATM frame relay 6 ==> standard … |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.44 | ColumnfrRoutingPriority | read-write | current | This is used by PXM to determine how important this connection is when selecting connections to route |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.45 | ColumnfrMaxCost | read-write | current | The value of this object specifies the Maximum allowed cost. It is related to Cost Based Routing. This is used by PXM so that it won't choose a path with a cos… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.46 | ColumnfrRestrictTrunkType | read-write | current | Restricted trunk type for routing, used by PXM. It specifies that the connection either cannot be routed over satelite trunks, or terrestrial trunks, or it can… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.47 | ColumnfrConnPCR | read-write | current | The value of this object identifies the PCR(Peak Cell Rate). If not provided in the connection setup request, it'll be derived from object 'pir'. For FRSM12 Ca… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.48 | ColumnfrConnRemotePCR | read-write | current | Peak cell rate of the other end, if not set, will be set to the same as local end PCR (frConnPCR). However, note that if the CIRs for both local and remote end… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.49 | ColumnfrConnMCR | read-write | current | Minimum cell rate, if not provided in the connection setup request, it'll be derived from object 'mir'. For FRSM12 Card: Default value is frConnPCR |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.50 | ColumnfrConnRemoteMCR | read-write | current | Minimum cell rate of the other end, if not set, will be set to the same as local end MCR (frConnMCR). However, note that if the CIRs for both local and remote … |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.51 | ColumnfrConnPercentUtil | read-write | current | This is the expected long-term utilization of the channel by this end-point. If this is not specified in the connection setup request, it'll be defaulted to 10… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.52 | ColumnfrConnRemotePercentUtil | read-write | current | This is the expected long-term utilization of the channel by the other end-point. If this is not specified in the connection setup request, it'll be set to be … |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.53 | ColumnfrConnForeSightEnable | read-write | current | This object is used by the controller(PAR/PNNI/TAG) to set up the Qbin for the connection, if this is not set, it'll be defaulted by SM to the same as foreSigh… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.54 | ColumnfrConnFGCRAEnable | read-write | current | The value of this object is used for enabling/disabling Frame based GCRA (early packet discard). For FRSM12 Card: Not Supported. |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.55 | ColumnchanServType | read-write | current | The value of this object indicates the indicates the class of the connection. 1-High priority (typically CBR connections) 2- real-time VBR 3- non-real time VBR… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.56 | ColumnchanServiceRateOverride | read-write | current | This variable sets the SAR IR programming option. Foresight and chanServiceRateOverride are mutually exclusive. For FRSM12 Card: Not Supported. |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.57 | ColumnchanServiceRate | read-write | current | This is the rate to which IR can be set to when chanServiceRateOverride is set to enable(1). If chanServiceRateOverride is disable(2) then this object does not… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.58 | ColumnzeroCirConEir | read-write | current | The value of this object defines defines EIR value for '0' CIR connection. If the value is '0', EIR is set to port speed. If zeroCirConEir is non-zero value, E… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.59 | ColumnchanReroute | read-write | current | This is used by the administrator to trigger the re-routing of the connection. The rerouting takes effect, when this object is set to true(1). When set to fals… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.60 | ColumnfrConnSCR | read-write | current | Sustained cell rate, Used for VBR connections setup with PNNI controller. For FRSM12 Card: Default value is frConnPCR This object is not applicable to MGX Rele… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.61 | ColumnfrConnRemoteSCR | read-write | current | Sustained cell rate of the other end, Used for VBR connections setup with PNNI controller. For FRSM12 Card: Default value is frConnSCR This object is not appli… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.62 | ColumnfrConnTemplateId | read-write | current | This object specifies the template identifier for the connection template associated with this connection. The valid range for templates is 1..16. A value of 1… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.63 | ColumnfrConnAdminStatus | read-write | current | This object specifies channel admin status. This object is not applicable to MGX Release 1.x. |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.64 | ColumnfrChanCnfChangeCount | read-only | current | This object is added only for FRSM12 card. This counter tracks the number of configuration changes that happen on a channel. The counter is associated only wit… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.65 | ColumnfrChanCnfIgnoreIncomingDE | read-write | current | This object is added for FRSM12 card. When this object is enabled, the incoming frames with DE(Discard Eligible) bit set to 1 are counted in the Bc bucket inst… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.66 | ColumnfrChanOamCCEnable | read-write | current | This object is added for FRSM12 card. This object serves to enable or disable continuity check(CC) on a connection endpoint. When continuity check is enabled o… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.67 | ColumnfrChanStatsEnable | read-write | current | This object serves the purpose of enabling/disabling statistics collection on a per connection basis. In implementations which do not have such limitations, th… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.68 | ColumnfrChanLocalLpbkEnable | read-write | current | This object is added for FRSM12 card. This object when enabled adds a channel-level loopback towards the port side. If the connection is in loopback, Connectio… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.69 | ColumnfrChanUpcEnable | read-write | current | This object is added for FRSM12 card. This object when disabled, disables Frame Relay policing. This object is not applicable to MGX Release 1.x. |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.70 | ColumnfrChanSlaveType | read-write | current | This object is added for FRSM12 card. This object indicates whether a master endpoint has a persistent slave or not. A connection with a master and a non-persi… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.71 | ColumnfrConnRemoteMBS | read-write | current | Remote Maximum Burst Size in terms of number of cells. This object should be set by the user in cases when the remote end of the connection is an ATM end-point… |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.72 | ColumnfrChanPrefRouteId | read-write | current | This object serves to to associate a preferred route with a connection. The value '0' means no preferred route is associated with this connection. Usage: - If … |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.73 | ColumnfrChanDirectRoute | read-write | current | This object serves to associate a prefer route as directed route (correspond to the prefer route object frChanPrefRouteId). A directed route specifies that the… |
| 1.3.6.1.4.1.351.110.5.1.2.1.2 | ScalarchanNumNextAvailable | read-only | current | This variable contains the next UNUSED channel number of the maximum possible value(depends upon the service module). This number can be used in channel config… |
| 1.3.6.1.4.1.351.110.5.1.2.1.3 | TablefrstdABRCnfGrpTable | not-accessible | current | This table is used for configuring ABR parameters on a frame relay connection. |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1 | RowfrstdABRCnfGrpEntry | not-accessible | current | An entry in ABR Configuration table. |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.1 | ColumnfrstdABRcnfChanNum | read-only | current | Refers to the virtual connection index. The value supported depends upon the type of service module. Supported Range for different Card Types: FRSM-4T1/E1 : su… |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.2 | ColumnfrstdABRTBE | read-write | current | The value of this object is equal to Transient Buffer Exposure(TBE). The TBE is a negotiated number of cells that the network would like to limit the source to… |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.3 | ColumnfrstdABRFRTT | read-write | current | The value of this object is equal to Fixed Round-Trip Time(FRTT). The FRTT is sum of the fixed propogation delays from the source to a destination network. The… |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.4 | ColumnfrstdABRRDF | read-write | current | The value of this object is equal to Rate Decrease Factor(RDF). The RDF controls the rate decrease which occurs when backward RM-cells with CI=1 are received. … |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.5 | ColumnfrstdABRRIF | read-write | current | The value of this object is equal to Rate Increase Factor(RIF). The RIF controls the rate increase which occurs when a backward RM-cell is received with CI=0 a… |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.6 | ColumnfrstdABRNrm | read-write | current | The value of this object is equal to number of cells a source may send for each forward RM cell. The valid values possible are only powers of 2 starting from 2… |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.7 | ColumnfrstdABRTrm | read-write | current | The value of this object is equal to Upper bound on the time between forward RM cells for an active source. |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.8 | ColumnfrstdABRCDF | read-write | current | The value of this object is equal to Cutoff Decrease Factor(CDF). The value specified has to be inverted to arrive at the actual value. The valid values possib… |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.9 | ColumnfrstdABRADTF | read-write | current | The value of this object is equal to ACR Decrease Time Factor(ADTF). The Granularity allowed is 10 milli seconds. i.e. 10,20,30 etc. The SNMP agent has to veri… |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.10 | ColumnfrstdABRICR | read-write | current | The value of this object is equal to Initial Cell Rate(ICR). The ICR is the rate at which the source should send initially and after an idle period. This inclu… |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.11 | ColumnfrstdABRMCR | read-write | current | The value of this object is equal to Minimum Cell Rate(MCR). The MCR is the rate at which the source is allowed to send. This includes the bandwidth allocated … |
| 1.3.6.1.4.1.351.110.5.1.2.1.3.1.12 | ColumnfrstdABRPCR | read-write | current | The value of this object is equal to Peak Cell Rate(PCR). The PCR is the rate at which the source is allowed to send. This includes the bandwidth allocated for… |
| 1.3.6.1.4.1.351.110.5.1.2.2 | NodefrChanStateGrp | |||
| 1.3.6.1.4.1.351.110.5.1.2.2.1 | TablefrChanStateGrpTable | not-accessible | current | Table of transmit/receive states of channels. |
| 1.3.6.1.4.1.351.110.5.1.2.2.1.1 | RowfrChanStateGrpEntry | not-accessible | current | An entry for FrChannelStateGrpEntry. |
| 1.3.6.1.4.1.351.110.5.1.2.2.1.1.1 | ColumnstateChanNum | read-only | current | The value of this object refers to frame relay connection. The value must be same as the value of the object 'chanNum' in frChanCnfGrpTable. |
| 1.3.6.1.4.1.351.110.5.1.2.2.1.1.2 | ColumnchanState | read-only | current | This variable indicates the LMI state of the VC (channel). The possible values are : notConfigured(1): Connection Not configured okay(2) : Connection is in Ok … |
| 1.3.6.1.4.1.351.110.5.1.2.2.1.1.3 | ColumnxmtAbitState | read-only | current | The value of this object identifies the A bit transmit state. The possible values are : off(1) : LMI is off sendingAequal1(2) : LMI is on and connection is O.K… |
| 1.3.6.1.4.1.351.110.5.1.2.2.1.1.4 | ColumnrcvAbitState | read-only | current | The value of this object identifies the A bit receive state. The possible values are : off(1) : LMI is off rcvingAequal1(2) : LMI is on and connection is O.K. … |
| 1.3.6.1.4.1.351.110.5.1.2.2.1.1.5 | ColumnxmtATMState | read-only | current | This variable indicates the transmit state of the VC (channel) on the ATM side. The possible values are : notSending(1) : Not sending any state sendingAIS(2) :… |
| 1.3.6.1.4.1.351.110.5.1.2.2.1.1.6 | ColumnrcvATMState | read-only | current | This variable indicates the receive state of the VC (channel) on the ATM side. The possible values are : notRcving(1) : Not receiving any state rcvingAIS(2) : … |
| 1.3.6.1.4.1.351.110.5.1.2.2.1.1.7 | ColumnchanStatusBitMap | read-only | current | This variable indicates the consolidated bit map of the channel alarm state. Individual bit positions are as defined below. Bit position Fail/Alarm Reason 0 Al… |
| 1.3.6.1.4.1.351.110.5.1.3 | NodefrEndPtMapGrp | |||
| 1.3.6.1.4.1.351.110.5.1.3.1 | TablefrEndPtMapGrpTable | not-accessible | current | This is the Endpoint Mapping table for Frame Relay connections. |
| 1.3.6.1.4.1.351.110.5.1.3.1.1 | RowfrEndPtMapGrpEntry | not-accessible | current | An entry in the frame relay connection Endpoint table. |
| 1.3.6.1.4.1.351.110.5.1.3.1.1.1 | ColumnendPortNum | read-only | current | This object identifies the frame relay logical port. The value for this object must be same as 'portNum' object in frPortCnfPortGrpTable. If ifTable is is impl… |
| 1.3.6.1.4.1.351.110.5.1.3.1.1.2 | ColumnendDLCI | read-only | current | The value of this object is equal to the DLCI value for this PVC endpoint. |
| 1.3.6.1.4.1.351.110.5.1.3.1.1.3 | ColumnendChanNum | read-only | current | The value of this object identifies the frame relay connection number. The value of this object is same as the value of 'chanNum' object in frChanCnfGrpTable. … |
| 1.3.6.1.4.1.351.110.5.1.3.1.1.4 | ColumnendLineNum | read-only | current | The value of this object is equal to the physical line(for example T1/E1) or ifIndex on which connection is provisioned. If ifTable is not implemented in a ser… |
| 1.3.6.1.4.1.351.150.47 | IdentityciscoWanFrConnMIB | The MIB module to configure the Frame Relay connection configuration. Terminologies Used: SIW - Frame-Relay-to ATM Service Interworking. In SIW, the ATM port c… | ||
| 1.3.6.1.4.1.351.150.47.2 | NodeciscoWanFrConnMIBConformance | |||
| 1.3.6.1.4.1.351.150.47.2.1 | NodeciscoWanFrConnMIBGroups | |||
| 1.3.6.1.4.1.351.150.47.2.1.1 | GroupciscoWanFrConnGroup | current | A collection of objects providing information applicable to a Frame Relay Connection. | |
| 1.3.6.1.4.1.351.150.47.2.1.2 | GroupciscoWanFrConnForesightGroup | current | A collection of objects related to foresight feature of a frame realay connection. | |
| 1.3.6.1.4.1.351.150.47.2.1.3 | GroupciscoWanFrConnQueueGroup | current | A collection of objects related to queue depth egress/ingress thresholds. | |
| 1.3.6.1.4.1.351.150.47.2.1.4 | GroupciscoWanFrConnTestGroup | current | A collection of objects related to testing Frame relay connections. | |
| 1.3.6.1.4.1.351.150.47.2.1.5 | GroupciscoWanFrConnStateGroup | current | A collection of objects related to state of Frame Relay connections. | |
| 1.3.6.1.4.1.351.150.47.2.1.6 | GroupciscoWanFrConnEndptGroup | current | A collection of objects related to Endpoint mapping in Frame Relay Connections. | |
| 1.3.6.1.4.1.351.150.47.2.1.7 | GroupciscoWanFrConnABRGroup | current | A collection of objects related to ABR in a frame relay connection. | |
| 1.3.6.1.4.1.351.150.47.2.2 | NodeciscoWanFrConnMIBCompliances | |||
| 1.3.6.1.4.1.351.150.47.2.2.1 | ComplianceciscoWanFrConnCompliance | current | The compliance statement for SNMP entities which support Frame realy connection MIB. |