CISCO-WAN-FR-PORT-MIB
118 objects
The MIB module to create/configure frame relay ports/interfaces. This module contains tables related to frame relay port states and statistics. The frame relay logical port is referred to as 'frame relay port' in this mib. Terminologies Used: Channel : Generically refers to the user access channel across which frame relay data travels. This is also referred to use logical port/interface in this MIB. Within a given T1 or E1 physical line, a channel can be one of the following, depending on how the line is configured. Unchannelized : The Entire T1/E1 line is considered a channel, where: * The T1 line operates at the speed of 1.536 Mbps and is single channel consisting of 24 T1 time slots. * The E1 line operates at the speed of 1.984 Mbps and is single channel consisting of 31 T1 time slots. Channelized: The channel is any one of the N time slots within a given line, where: * The T1 line consists of any one or more channels. Each channel is any one of 24 time slots. * The E1 line consists of one or more channels. Each channel is any one of 31 time slots. Fractional: The T1/E1 channel is one of the following groupings of consecutively or nonconsecutively assigned time slots: * N T1 time slots(N*56/64Kbps where N=1-23 T1 Time slots per FT1 channel. * N E1 time slots(N*64Kbps where N=1-30 Time slots per E1: channel. SVC : Switched Virtual Circuits. SVCs allow access through a Frame Relay Network by setting up a path to the destination endpoints only when the need arises and tearing down the path when it is no longer needed. Refer ITU Q.933 and Q.922 FECN : Forward Explicit Congestion Notification A bit set by a frame relay network to notify an interface device(DTE) that congestion avoidance procedures should be initiated by the receiving device. BECN : Backward Explicit Congestion Notification A bit set by a frame relay network to notify an interface device(DTE) that congestion avoidance procedures should be initiated by the sending device. DE : Discard Eligibility A user-bit set indicating that a frame may be discarded in preference to other frames if congestion occurs, to maintain the committed quality of service within the network. Frames with the DE bit set are considered Be(Excess Burst Size)excess data. Unchannelized Service Modules: Following Service Modules does not support channelized interfaces(i.e supports only unchannelized). FRSM-VHS : FRSM-2T3/2E3, FRSM-HS2/HS2B, FRSM-T3B/E3B For following service modules, ifTable is supported: FRSM-12.
Imported Objects
| BASIS-MIB | frPort frPortCnf frPortCnt frPortServiceQueGrp |
| CISCOWAN-SMI | ciscoWan |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY OBJECT-TYPE |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.351.110.5.1.1.1.1 | NodefrPortCnfPortGrp | |||
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1 | TablefrPortCnfPortGrpTable | not-accessible | current | This table is used for creating/configuring Frame Relay Logical(referred to as frame relay port)Ports. Relation with ifTable: The modules in which ifTable is i… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1 | RowfrPortCnfPortGrpEntry | not-accessible | current | An entry in the frame relay port table. |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.1 | ColumnportNum | read-only | current | This is the frame relay(logical) port number. For Service Modules, supporting ifTable, this must be the ifIndex value of the frame relay port. The port number … |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.2 | ColumnportLineNum | read-write | current | This object represents the physical line number on which the frame relay port need to be created. For Service Modules, supporting ifTable, this must be the ifI… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.3 | ColumnportRowStatus | read-write | current | The value of this object is used for creating modifying or deleting frame relay ports. The possible values are : add(1) : Create frame relay port del(2) : Dele… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.4 | ColumnportDs0ConfigBitMap | read-write | current | This respesents bit map of DS0s for a line/interface which are used to form this logical port. The Bit 0 represents DS0-1(First DS0 timeslot). This object is n… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.5 | ColumnportDs0Speed | read-write | current | The value of this object is used for configuring the port speed(or data rate) of Ds0 in frame relay port. speed56k(1) : set to 56k speed64k(2) : set to 64k unU… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.6 | ColumnportFlagsBetweenFrames | read-write | current | Number of flags transmitted between FR frames For FRSM12 card: Only the values 1 to 8 are supported. The mapping is as follows: MIB object value No. of HDLC fl… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.7 | ColumnportEqueueServiceRatio | read-write | current | Number of times queue 1 is serviced for every time queue 2 is serviced. The value 0 is supported only by FRSM-VHS. FRSM-VHS supports two different egress queue… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.8 | ColumnportSpeed | read-only | current | The value of this object contains the Configured speed of port. |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.9 | ColumnportAdmin | read-write | current | The value of this object is used for changing the desired state of the port. up(1) : Up the port;Admin up down(2) : Down the port;Admin down For Service Module… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.10 | ColumnportType | read-write | current | The value of this object identifies the network interface for this frame relay port. The Possible values are: frame-relay(1) : Frame Relay Service Port frFUNI … |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.11 | ColumnportSvcStatus | read-write | current | The value of this object is used for enabling/disabling the SVC operation on a frame relay port. For FRSM12 card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.12 | ColumnportSvcInUse | read-write | current | The value of this object is used for representing whether SVC is in use or not. For FRSM12 card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.13 | ColumnportSvcShareLcn | read-only | current | The value of this object identifies the SVC shared LCN type. For FRSM12 card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.14 | ColumnportSvcLcnLow | read-only | current | The value of this object identifies the low end of the reserved LCN for SVC. For FRSM12 card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.15 | ColumnportSvcLcnHigh | read-only | current | The value of this object identifies the high end of reserved LCN for SVC. For FRSM12 card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.16 | ColumnportSvcDlciLow | read-only | current | The value of this object identifies the low end of reserved DLCI for SVC. For FRSM12 card: Not Supported. |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.17 | ColumnportSvcDlciHigh | read-only | current | The value of this object identifies the high end of reserved DLCI for SVC. For FRSM12 card: Not Supported. |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.18 | ColumnportDeleteSvcs | read-write | current | The value of this object indicates that all the SVC connections on a given frame relay port has to be deleted. For FRSM12 card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.19 | ColumnportIngrSvcBandW | read-only | current | The value of this object identifies the Ingress bandwidth reserved for SVC. For FRSM12 card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.20 | ColumnportEgrSvcBandW | read-only | current | The value of this object identifies the Egress bandwidth reserved for SVC. For FRSM12 card: Not Supported. |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.21 | ColumnportBERTEnable | read-write | current | The value of this object enables/disables the Bit Error Rate Testing (BERT) on the frame relay port. For FRSM12 card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.22 | ColumnportEnhancedSIW | read-write | current | This variable enables/disables enhanced SIW feature. Enabling this permits support for SIW translation of Appletalk. This feature is supported only in the FRSM… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.23 | ColumnportM32EgrQueueThresh | read-write | current | This represents the M32 logical port Egress Queue threshold in bytes. Frames will not be queued until the number of bytes in the queue is less than the thresho… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.24 | ColumnportHeaderLen | read-write | current | The value of this object identifies the Q.922 address field length and DLCI length for this UNI/NNI logical port. This object can not be modified if there are … |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.25 | ColumnportFrameChkSumType | read-write | current | The value of this object identifies the CRC Length in the HDLC Packet. Applicable for FrameForwarding ports only. This object can not be modified if there are … |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.26 | ColumnportFileId | read-write | current | The value of this object identifies the Service Class Template(SCT) file ID. The SCT holds the module specific configuration parameters for the frame relay por… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.27 | ColumnportOverSubEnable | read-write | current | The value of this object enables/disables the port to be over subscribed. This object is not applicable to MGX Release 1.x. |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.2 | ScalarportsUsedLine1 | read-only | current | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1. This is for lin… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.3 | ScalarportsUsedLine2 | read-only | current | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1. This is for lin… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.4 | ScalarportsUsedLine3 | read-only | current | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1. The most significant byte is invalid for DS1. This is for lin… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.5 | ScalarportsUsedLine4 | read-only | current | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1. The most significant byte is invalid for DS1. This is for lin… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.6 | ScalarportNextAvailable | read-only | current | This variable contains the next UNUSED logical port number. This number can be used in channel config table, the portNextAvailable gets updated if the number g… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.7 | ScalarportsUsedLine5 | read-only | current | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1. The most significant byte is invalid for DS1. This is for lin… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.8 | ScalarportsUsedLine6 | read-only | current | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1. The most significant byte is invalid for DS1. This is for lin… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.9 | ScalarportsUsedLine7 | read-only | current | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1. The most significant byte is invalid for DS1. This is for lin… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.10 | ScalarportsUsedLine8 | read-only | current | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1. The most significant byte is invalid for DS1. This is for lin… |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.11 | TablefrPortsUsedLineGrpTable | not-accessible | current | This table Contains information on the DS0 time slots used in each DS1 interface. |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.11.1 | RowfrPortsUsedLineGrpEntry | not-accessible | current | An entry for each DS1 interface. |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.11.1.1 | ColumnfrPortsUsedLineIndex | read-only | current | This object uniquely identifies the DS1 interface. |
| 1.3.6.1.4.1.351.110.5.1.1.1.1.11.1.2 | ColumnfrPortsUsedLine | read-only | current | The value of this object provides the information on DS0 time slots used by the DS1 identified by 'frPortsUsedLineIndex' object. A bit set represents a DS0 tha… |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1 | TablefrPortServiceQueGrpTable | not-accessible | current | The config table is for logical port interface. In FRSM-VHS, there are 256 entries for FRSM-2CT3 card and 2 entries for FRSM-T3/E3/HS2/T3B/E3B/HS2B-HSSI cards … |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1 | RowfrPortServiceQueGrpEntry | not-accessible | current | An entry for logical port. |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.1 | ColumnfrServPortNum | read-only | current | This is the frame relay port number. The value of this object must match with the value of object 'portNum' in frPortCnfPortGrpTable. |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.2 | ColumnportServiceQueueNo | read-write | current | This identifies the Q depending on the Service Type 1 High Priority Queue 2 rt VBR Queue 3 nrt VBR and ABR Queue 4 UBR Queue queue5(5) to queue8(8) are reserve… |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.3 | ColumnportEgresQDepth | read-write | current | Indicates the peak Egress queue depth for the frame relay port. The total queue depth of all connections mapped to this queue should not exceed this value. |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.4 | ColumnportEgresECNThresh | read-write | current | ECN threshold for the frame relay port. If the total queue depth of all connections mapped to this port queue exceeds this threshold, then the appropriate ECN … |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.5 | ColumnportEgresDEThresh | read-write | current | DE threshold for the frame relay port. If the total queue depth of all connections mapped to this port queue exceeds this threshold, and the DE bit is set in t… |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.6 | ColumnportQBwInc | read-only | current | Denotes the bandwidth increment for this port queue. The bandwidth increment is the percentage of the port bandwidth used by all connections mapped to a partic… |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.7 | ColumnportBytesDiscXceedQueFull | read-only | current | Counter maintained for the no of bytes discarded due to port queue depth exceeded. |
| 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.8 | ColumnportBytesDiscXceedDEThresh | read-only | current | Counter maintained for the no of bytes discarded due to DE threshold exceeded. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1 | NodefrPortCntPortGrp | |||
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1 | TablefrPortCntPortGrpTable | not-accessible | current | The config table is for logical port interface there are upto 248 entries (for 8 E1s) or 192 (for 8 T1s). In FRSM-VHS, there is support for upto 256 entries. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1 | RowfrPortCntPortGrpEntry | not-accessible | current | An entry for logical port |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.1 | ColumncntPortNum | read-only | current | This is the frame relay(logical) port number. The value of this object must be same as the value of object 'portNum' in frPortCnfPortGrpTable. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.2 | ColumnrcvPortFrames | read-only | current | The number of frames Received on the ingress. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.3 | ColumnrcvPortBytes | read-only | current | The number of bytes Received on the ingress. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.4 | ColumnrcvPortFramesDE | read-only | current | The number of frames with DE bit set received on the ingress. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.5 | ColumnrcvPortFramesFECN | read-only | current | The number of frames with FECN bit set received on the ingress. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.6 | ColumnrcvPortFramesBECN | read-only | current | The number of frames with BECN bit set received on the ingress. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.7 | ColumnrcvFramesDiscCRCError | read-only | current | The number of frames discarded on the ingress due to CRC error. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.8 | ColumnrcvFramesDiscAlignmentError | read-only | current | The number of frames discarded on the ingress due to Alignment error. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.9 | ColumnrcvFramesDiscIllegalLen | read-only | current | The number of frames discarded on the ingress due to illegal length. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.10 | ColumnrcvFramesDiscIllegalHeader | read-only | current | The number of frames discarded on the ingress due to illegal header. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.11 | ColumnrcvFramesAbort | read-only | current | The number of received frames aborted |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.12 | ColumnrcvFramesUnknownDLCI | read-only | current | The number of frames received with an unknown DLCI. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.13 | ColumnrcvLastUnknownDLCI | read-only | current | The last unknown DLCI received. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.14 | ColumnrcvPortFramesTaggedFECN | read-only | current | The number of frames received that were tagged with FECN bit. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.15 | ColumnrcvPortFramesTaggedBECN | read-only | current | The number of frames received that were tagged with BECN bit. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.16 | ColumnrcvPortFramesTaggedDE | read-only | current | The number of frames received that were tagged with DE bit. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.17 | ColumnrcvPortFramesDiscXceedDEThresh | read-only | current | The number of frames discarded on the ingress due to exceeded DE Threshold. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.18 | ColumnrcvPortKbpsAIR | read-only | current | Received Average Information Rate in KBPS. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.19 | ColumnrcvBufNotAvailable | read-only | current | The number of times the receiver is turned off |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.20 | ColumnxmtPortFrames | read-only | current | The number of frames transmitted. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.21 | ColumnxmtPortBytes | read-only | current | The number of bytes transmitted. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.22 | ColumnxmtPortFramesFECN | read-only | current | The number of frames transmitted with FECN bit already set. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.23 | ColumnxmtPortFramesBECN | read-only | current | The number of frames transmitted with BECN bit already set. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.24 | ColumnxmtPortFramesDiscXceedQDepth | read-only | current | The number of frames discarded on the egress due to exceeded queue depth For FRSM12 Card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.25 | ColumnxmtPortBytesDiscXceedQDepth | read-only | current | The number of bytes discarded on the egress due to exceeded queue depth For FRSM12 Card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.26 | ColumnxmtPortFramesDuringLMIAlarm | read-only | current | The number of frames transmitted during LMI logical port alarm |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.27 | ColumnxmtPortBytesDuringLMIAlarm | read-only | current | The number of bytes transmitted during LMI logical port alarm |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.28 | ColumnxmtFramesAbort | read-only | current | The number of transmit frames aborted For FRSM12 Card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.29 | ColumnxmtFramesUnderrun | read-only | current | The number of frames discarded due to underrun. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.30 | ColumnxmtPortKbpsAIR | read-only | current | Transmit Average Information Rate in KBPS. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.31 | ColumnxmtBufNotAvailable | read-only | current | The number of times the transmitter is turned off For FRSM12 Card: Not Supported |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.32 | ColumnportClrButton | read-write | current | The value of this object is used for clearing all the port related statistics counters. clear(2) : Clears the Counters. noaction(1) : No action taken. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.33 | ColumnrcvFramesDiscNoChan | read-only | current | The number of frames received when no channel is setup. |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.34 | ColumnrcvFramesDiscOverrun | read-only | current | The number of frames discarded in Ingress direction due to FIFO overrun in HDLC Controller. This object is not applicable to MGX Release 1.x |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.35 | ColumnrcvPortFramesDiscard | read-only | current | Number of framesdiscarded in the ingress direction by the port |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.36 | ColumnxmtPortFramesDE | read-only | current | Number of frames transmitted in the egress direction by the port with DE bit set to 1 |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.37 | ColumnxmtPortBytesDE | read-only | current | Number of bytes transmitted in the egress direction by the port with DE bit set to 1 |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.38 | ColumnrcvPortBytesDE | read-only | current | Number of bytes received in the ingress direction by the port with DE bit set to 1 |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.39 | ColumnxmtPortFramesDiscXceedDEThresh | read-only | current | Number of frames discarded in the egress direction by the port due to exceeded DE Threshold |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.40 | ColumnxmtPortBytesDiscXceedDEThresh | read-only | current | Number of bytes discarded in the egress direction by the port due to exceeded DE Threshold |
| 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.41 | ColumnrcvPortBytesDiscXceedDEThresh | read-only | current | Number of bytes discarded in the ingress direction by the port due to exceeded DE Threshold |
| 1.3.6.1.4.1.351.110.5.1.1.3 | NodefrPortStateGrp | |||
| 1.3.6.1.4.1.351.110.5.1.1.3.1 | TablefrPortStateGrpTable | not-accessible | current | Table of transmit/receive states of ports. |
| 1.3.6.1.4.1.351.110.5.1.1.3.1.1 | RowfrPortStateGrpEntry | not-accessible | current | An entry for logical port. |
| 1.3.6.1.4.1.351.110.5.1.1.3.1.1.1 | ColumnstatePortNum | read-only | current | This is the frame relay(logical) port number. The value of this object must match with the value of object 'portNum' in frPortCnfPortGrpTable. |
| 1.3.6.1.4.1.351.110.5.1.1.3.1.1.2 | ColumnportState | read-only | current | This variable indicates the state of the logical port |
| 1.3.6.1.4.1.351.110.5.1.1.3.1.1.3 | ColumnportSignallingState | read-only | current | Bit 0 = 0 -> LMI O.K. or not enabled Bit 0 = 1 -> LMI failed Bit 1 = 0 -> CLLM O.K. or not enabled Bit 1 = 1 -> CLLM failed |
| 1.3.6.1.4.1.351.110.5.1.1.3.1.1.4 | ColumnportOversubscribed | read-only | current | This variable indicates the whether the port is over subscribed or not. |
| 1.3.6.1.4.1.351.110.5.1.1.3.1.1.5 | ColumnportIngrPercentUtil | read-only | current | Percentage Utilization of the Port in the Ingress direction. |
| 1.3.6.1.4.1.351.110.5.1.1.3.1.1.6 | ColumnportEgrPercentUtil | read-only | current | Percentage Utilization of the Port in the Egress direction. |
| 1.3.6.1.4.1.351.150.44 | IdentityciscoWanFrPortMIB | The MIB module to create/configure frame relay ports/interfaces. This module contains tables related to frame relay port states and statistics. The frame relay… | ||
| 1.3.6.1.4.1.351.150.44.2 | NodeciscoWanFrPortMIBConformance | |||
| 1.3.6.1.4.1.351.150.44.2.1 | NodeciscoWanFrPortMIBGroups | |||
| 1.3.6.1.4.1.351.150.44.2.1.1 | GroupciscoWanFrPortConfGroup | current | The collection of objects which are used to represent Frame Relay Port information. | |
| 1.3.6.1.4.1.351.150.44.2.1.2 | GroupciscoWanFrPortSvcGroup | current | The collection of objects which are used to represent SVC characteristics of a Frame Relay Port. | |
| 1.3.6.1.4.1.351.150.44.2.1.3 | GroupciscoWanFrPortDs0InDs1Group | current | The objects representing the DS0(in DS1) that are used by the frame relay logical ports. | |
| 1.3.6.1.4.1.351.150.44.2.1.4 | GroupciscoWanFrPortStateGroup | current | The collection of objects related to state information of Frame Relay Ports. | |
| 1.3.6.1.4.1.351.150.44.2.1.5 | GroupciscoWanFrPortStatsGroup | current | The collection of objects related to statistics information of frame relay ports. | |
| 1.3.6.1.4.1.351.150.44.2.1.6 | GroupciscoWanFrPortServiceQueueGroup | current | The collection of objects related to service queue on frame relay ports. | |
| 1.3.6.1.4.1.351.150.44.2.1.7 | GroupciscoWanFrPortsUsedGroup | current | The collection of objects related to information on DS0 time slots used in each DS1 line. | |
| 1.3.6.1.4.1.351.150.44.2.2 | NodeciscoWanFrPortMIBCompliances | |||
| 1.3.6.1.4.1.351.150.44.2.2.1 | ComplianceciscoWanFrPortCompliance | current | The compliance statement for objects related to Frame Relay Ports. |