CISCO-WAN-FR-X21-MIB
58 objects
The MIB module to configure X.21/HSSI physical and logical interfaces. This MIB module also contains alarm configuration of X.21 interfaces. Terminologies Used: HSSI : High Speed Serial Interface. The HSSI defines both electrical and physical interfaces on DTE and DCE devices. It operates at the physical layer of the OSI reference model. This provides high-speed data communication over WAN and LAN links.
Imported Objects
| BASIS-MIB | frPortCnfX21PortGrp x21 |
| CISCOWAN-SMI | ciscoWan |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY OBJECT-TYPE |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.351.110.4.5.1 | Nodex21CnfGrp | |||
| 1.3.6.1.4.1.351.110.4.5.1.1 | Tablex21CnfGrpTable | not-accessible | current | The X21 Configuration table. The table size is given by the value of x21LineNumofValidEntries. |
| 1.3.6.1.4.1.351.110.4.5.1.1.1 | Rowx21CnfGrpEntry | not-accessible | current | An entry in the X21 Configuration table. |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.1 | Columnx21LineNum | read-only | current | This object is the identifier of a X.21 interface. FRSM-HS2/HS2B-HSSI supports a range from 1 to 2. FRSM-HS2B-12IN1 supports a range from 1 to 8. |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.2 | Columnx21LineEnable | read-write | current | This variable disables, enables or modifies a line 1 - disable 2 - enable 3 - modify Default is enable. |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.3 | Columnx21LineType | read-write | current | This variable indicates the type X21 line type. The line-type affects the clock always provides the clock and DTE accepts it. dteST is only applicable to V.35 … |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.4 | Columnx21LineRate | read-write | current | This variable configures the X.21/HSSI/V.35 line-rate. Note that enumerations 51 through 108 are supported only by FRSM-HS2/HS2B card. default is r48Kbps on FR… |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.5 | Columnx21LineLoopbackCommand | read-write | current | This variable represents the loopback state x21NoLoop Not in the loopback state. Normal traffic can be sent x21DiagnosticMetallicLoop Loopbacks the line on the… |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.6 | Columnx21LineSendCode | read-write | current | This variable indicates what type of code is being sent across the X.21/HSSI interface by the device. The values mean: x21NoCode: No loopback. x21SendLoopACode… |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.7 | Columnx21LineLoopbackCodeDetection | read-write | current | Enable detection of line Loopback Codes. The loopback detection is implemented only in HSSI DCE mode. Default is codeDetectDisabled. |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.8 | Columnx21ConnectorType | read-only | current | back card type This object is not used by FRSM-HS2/HS2B |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.9 | Columnx21InvertClock | read-write | current | This object configures two options: a) To invert the clock sent by HS1/HS2B with the TX data or not. b) If DCE,to expect the receive clock looped back from DTE… |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.10 | Columnx21LineInterfaceType | read-write | current | This object indicates serial interface type. Default is hssi(1). This object is not is configurable in FRSM-HS2 and FRSM-HS2B-HSSI. It will be set to hssi(1) b… |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.11 | Columnx21ClkFrequencyThreshold | read-write | current | This object indicates user configurable percentage of clock frequency, which is used by DTE clock monitoring to declare clock rate out of bound alarm. This obj… |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.12 | ColumnserialLineRate | read-write | current | Line rate for X.21/HSSI/V.35 interfaces in bps. This object is supported only by FRSM-HS2/B card, only multiples of 1000 are accepted. Default is 48Kbps for X.… |
| 1.3.6.1.4.1.351.110.4.5.1.1.1.13 | ColumnserialLineRateVariation | read-only | current | This object indicates line rate variation of HSSI/X.21/V.35 DCE interfaces in ppm (parts per million). i.e. clock generated from DCE hardware interface = (seri… |
| 1.3.6.1.4.1.351.110.4.5.1.2 | Scalarx21LineNumofValidEntries | read-only | current | The number of X.21/HSSI configuration entries (regardless of their current configuration) in the x21ConfigTable table. |
| 1.3.6.1.4.1.351.110.4.5.2 | Nodex21AlmCnfGrp | |||
| 1.3.6.1.4.1.351.110.4.5.2.1 | Tablex21AlmCnfGrpTable | not-accessible | current | The FRSM-HS1/HS2 interface alarm configuration table. |
| 1.3.6.1.4.1.351.110.4.5.2.1.1 | Rowx21AlmCnfGrpEntry | not-accessible | current | An entry in the X.21/HSSI Alarm Configuration table. |
| 1.3.6.1.4.1.351.110.4.5.2.1.1.1 | Columnx21AlmCnfLineNum | read-write | current | X.21/HSSI line number. FRSM-HS2/HS2B-HSSI supports a range from 1 to 2. FRSM-HS2B-12IN1 supports a range from 1 to 8. |
| 1.3.6.1.4.1.351.110.4.5.2.1.1.2 | Columnx21Severity | read-write | current | This variable is used to setup the severity of LOS(Loss of Signal) or clock mismatch alarm. Whenever the above condition arises, the FRSM-HS1/HS2/HS2B will sen… |
| 1.3.6.1.4.1.351.110.4.5.3 | Nodex21AlmGrp | |||
| 1.3.6.1.4.1.351.110.4.5.3.1 | Tablex21AlmGrpTable | not-accessible | current | The X.21/HSSI interface alarm configuration table. |
| 1.3.6.1.4.1.351.110.4.5.3.1.1 | Rowx21AlmGrpEntry | not-accessible | current | An entry in the X21 Alarm table |
| 1.3.6.1.4.1.351.110.4.5.3.1.1.1 | Columnx21AlmLineNum | read-only | current | This object is the identifier (line number) of a X.21/HSSI interface. The value for this object must be same as the value of x21LineNum. |
| 1.3.6.1.4.1.351.110.4.5.3.1.1.2 | Columnx21LineAlarmState | read-only | current | This variable is a bitmap of the X21 Line ALarms on the FRSM-HS1. A value of zero indicates no alarms. Itemized below are the individual bits: BitPosition Alar… |
| 1.3.6.1.4.1.351.110.4.5.3.1.1.3 | Columnx21LineEIAStatus | read-only | current | |
| 1.3.6.1.4.1.351.110.4.5.3.1.1.4 | Columnx21AlarmClrButton | read-write | current | This variable is used to clear all the alarms for the line. 1 = No action 2 = Clear alarm. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1 | TablefrPortCnfX21PortGrpTable | not-accessible | current | The config table is for X.21/HSSI logical port interface |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1 | RowfrPortCnfX21PortGrpEntry | not-accessible | current | An entry for logical port. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.1 | Columnx21portNum | read-only | current | This is logical port number. The HSSI backcard can support upto 3 ports. The X.21 back card can support 4 logical ports. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.2 | Columnx21portLineNum | read-write | current | This represents the line number. On FRSM-HS1 the HSSI can support 3 lines and X.21 4 lines. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.3 | Columnx21portRowStatus | read-write | current | This variable adds, deletes, or modifies the port 1- add 2 - delete 3 - modify Default is add. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.4 | Columnx21portFlagsBetweenFrames | read-write | current | Number of flags transmitted between two consecutive HDLC frames. Default is 1 flag. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.5 | Columnx21portEqueueServiceRatio | read-write | current | Number of times queue 1 is serviced for every time queue 2 is serviced. Default is 1. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.6 | Columnx21portSpeed | read-only | current | Port speed in kbps. At present it is same as line speed. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.7 | Columnx21portAdmin | read-write | current | This object is used for administratively changing the status of the port. Up/down used to up and down the port. Default is the up state. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.8 | Columnx21portType | read-write | current | This represents port type. The processing of the frames depends on the type of the port. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.9 | Columnx21portSvcStatus | read-write | current | This represents SVC status. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.10 | Columnx21portSvcInUse | read-write | current | This represents port SVC in use. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.11 | Columnx21portSvcShareLcn | read-only | current | This represents port type. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.12 | Columnx21portSvcLcnLow | read-only | current | This represents low end of reserved LCN for SVC. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.13 | Columnx21portSvcLcnHigh | read-only | current | This represents high end of reserved LCN for SVC. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.14 | Columnx21portSvcDlciLow | read-only | current | This represents low end of reserved DLCI for SVC. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.15 | Columnx21portSvcDlciHigh | read-only | current | This represents high end of reserved DLCI for SVC. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.16 | Columnx21portDeleteSvcs | read-write | current | Setting this object to 1 indicates that all the SVC connections on the given port has to be deleted. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.17 | Columnx21portIngrSvcBandW | read-only | current | This represents Ingress Bandwidth reserve for SVC. |
| 1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.18 | Columnx21portEgrSvcBandW | read-only | current | This represents Egress Bandwidth reserve for SVC. |
| 1.3.6.1.4.1.351.150.49 | IdentityciscoWanFrX21MIB | The MIB module to configure X.21/HSSI physical and logical interfaces. This MIB module also contains alarm configuration of X.21 interfaces. Terminologies Used… | ||
| 1.3.6.1.4.1.351.150.49.2 | NodecwfX21MIBConformance | |||
| 1.3.6.1.4.1.351.150.49.2.1 | NodecwfX21MIBGroups | |||
| 1.3.6.1.4.1.351.150.49.2.1.1 | GroupciscoWanFrX21PortGroup | current | The collection of objects which are applicable for X21 ports in frame relay. | |
| 1.3.6.1.4.1.351.150.49.2.1.2 | GroupciscoWanFrX21LineGroup | current | The collection of objects which are related to x21 lines. | |
| 1.3.6.1.4.1.351.150.49.2.1.3 | GroupciscoWanFrX21AlarmConfGroup | current | The collection of objects which are related to x21 lines. | |
| 1.3.6.1.4.1.351.150.49.2.1.4 | GroupciscoWanFrX21AlarmGroup | current | The collection of objects which are related to x21 lines. | |
| 1.3.6.1.4.1.351.150.49.2.2 | NodecwfX21MIBCompliances | |||
| 1.3.6.1.4.1.351.150.49.2.2.1 | CompliancecwfX21Compliance | current | The compliance statement for objects related to Frame Relay Ports. |