CISCO-WAN-T38-FAXRELAY-MIB
29 objects
The MIB module for configuring T.38 fax relay protocol parameters. This MIB will be used in VoIP(Voice over IP) applications.
Imported Objects
| CISCOWAN-SMI | ciscoWan |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY OBJECT-TYPE |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.351.150.19 | IdentityciscoWanT38FaxRelayMIB | The MIB module for configuring T.38 fax relay protocol parameters. This MIB will be used in VoIP(Voice over IP) applications. | ||
| 1.3.6.1.4.1.351.150.19.1 | NodeciscoWanT38FaxRelayMIBObjects | |||
| 1.3.6.1.4.1.351.150.19.1.1 | Nodet38FaxRelayGrp | |||
| 1.3.6.1.4.1.351.150.19.1.1.1 | Tablet38FaxRelayGrpTable | not-accessible | current | This table contains configuration information about various fax relay parameters used in VoIP calls on voice interface. |
| 1.3.6.1.4.1.351.150.19.1.1.1.1 | Rowt38FaxRelayGrpEntry | not-accessible | current | An entry is created when a DS1 interface is configured. An entry is deleted when a DS1 interface is removed. All configurations information in an entry is appl… |
| 1.3.6.1.4.1.351.150.19.1.1.1.1.1 | Columnt38vismDs1Number | not-accessible | current | This object identifies the unique DS1 value for a T1/E1 interface. |
| 1.3.6.1.4.1.351.150.19.1.1.1.1.2 | Columnt38MaxFaxTxRate | read-write | current | This object is used for configuring the maximum fax transmission rate. 'fx2400bps' - maximum transmission rate in 2400 bps. 'fx4800bps' - maximum transmission … |
| 1.3.6.1.4.1.351.150.19.1.1.1.1.3 | Columnt38FaxInfoFieldSize | read-write | deprecated | This object is used to configure the fax information field size in bytes. |
| 1.3.6.1.4.1.351.150.19.1.1.1.1.4 | Columnt38HsDataPacketSize | read-write | current | This object specifies the size of primary high speed(HS) - the data packet transmitted after the first phase of a T.38 call. 'tenms' - size of the HS in 10 mil… |
| 1.3.6.1.4.1.351.150.19.1.1.1.1.5 | Columnt38LsDataRedundancy | read-write | current | This object determines the extent of the internet fax protocol(IFP) packet transmission redundancy for the low-speed control information exchanged during the f… |
| 1.3.6.1.4.1.351.150.19.1.1.1.1.6 | Columnt38HsDataRedundancy | read-write | current | This object determines the extent of the IFP packet transmission redundancy for the high-speed control and image information exchanged following the initial lo… |
| 1.3.6.1.4.1.351.150.19.1.1.1.1.7 | Columnt38TCFmethod | read-write | current | This object determines the method used to verify the TCF(Training Check Field). For UDP-based fax transport, its value should be set to networkTCF. For TCP-bas… |
| 1.3.6.1.4.1.351.150.19.1.1.1.1.8 | Columnt38ErrCorrection | read-write | deprecated | This object is used to enable/disable the FEC scheme for UDP-based fax transport. |
| 1.3.6.1.4.1.351.150.19.1.1.1.1.9 | Columnt38NSFOverride | read-write | current | This object is used to enable/disable the gateway to override the NSF(Non-Standard Facilities) code in the following T.30 signals: NSF, NSC (Non-Standard Facil… |
| 1.3.6.1.4.1.351.150.19.1.1.1.1.10 | Columnt38NSFCountryCode | read-write | current | The Country Code in the NSF code is a single-byte field identifying the country where the group 3 fax equipment with non-standard capabilities were manufacture… |
| 1.3.6.1.4.1.351.150.19.1.1.1.1.11 | Columnt38NSFVendorCode | read-write | current | The Vendor Code (also called the Terminal Provider Code) in the NSF code is a two-byte field identifying the manufacturer of the group 3 fax equipment with non… |
| 1.3.6.1.4.1.351.150.19.1.1.1.1.12 | Columnt38NseAckTimeOut | read-write | current | This object defines a timeout value in milliseconds for a provision able timer. This timer is started after sending a NSE(Named Signal Event) 200 while waiting… |
| 1.3.6.1.4.1.351.150.19.1.1.1.1.13 | Columnt38FxLCO | read-write | current | This object is a configurable default value for the fx(fax option) in LCO(Local Connection Option). In the absence of the MGCP fx LCO, this default value will … |
| 1.3.6.1.4.1.351.150.19.1.1.1.1.14 | Columnt38Redundancy | read-write | deprecated | This object is used to enable/disable the Redundancy scheme for UDP-based fax transport. |
| 1.3.6.1.4.1.351.150.19.1.1.1.1.15 | Columnt38T30ECM | read-write | current | This object is used to enable/disable T.30 Error Correcting Mode(ECM). ECM is a feature implemented by many new fax devices which improves image quality and pa… |
| 1.3.6.1.4.1.351.150.19.2 | Nodet38NotificationPrefix | |||
| 1.3.6.1.4.1.351.150.19.2.0 | Nodet38Notifications | |||
| 1.3.6.1.4.1.351.150.19.3 | Nodet38FaxRelayMIBConformance | |||
| 1.3.6.1.4.1.351.150.19.3.1 | Nodet38FaxRelayMIBCompliances | |||
| 1.3.6.1.4.1.351.150.19.3.1.1 | Compliancet38FaxRelayMIBCompliance | deprecated | The compliance statement for t38 fax relay group which implement t38FaxRelayGrp MIB. | |
| 1.3.6.1.4.1.351.150.19.3.1.2 | Compliancet38FaxRelayMIBComplianceRev1 | current | The compliance statement for t38 fax relay group which implement t38FaxRelayGrp MIB. | |
| 1.3.6.1.4.1.351.150.19.3.2 | Nodet38FaxRelayMIBGroups | |||
| 1.3.6.1.4.1.351.150.19.3.2.1 | Groupt38FaxRelayGroup | deprecated | This group contains objects related to configuration of T38 fax relay. | |
| 1.3.6.1.4.1.351.150.19.3.2.2 | Groupt38FaxRelayGroupRev1 | current | The collection of objects that were supported earlier but deprecated now. |