CISCO-WAN-VISM-TONE-PLAN-MIB
63 objects
The MIB module is defined to configure the programmable Tone Plan feature on VISM.
Imported Objects
| CISCOWAN-SMI | ciscoWan |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | DisplayString RowStatus |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.351.150.24 | IdentityvismTonePlanGrpMIB | The MIB module is defined to configure the programmable Tone Plan feature on VISM. | ||
| 1.3.6.1.4.1.351.150.24.1 | NodevismTonePlanGrpMIBObjects | |||
| 1.3.6.1.4.1.351.150.24.1.1 | NodevismTonePlan | |||
| 1.3.6.1.4.1.351.150.24.1.1.1 | NodevismTonePlanControlGrp | |||
| 1.3.6.1.4.1.351.150.24.1.1.1.1 | ScalartonePlanCurrentSize | read-only | current | This object specifies the number of entries in vismTonePlanTable. |
| 1.3.6.1.4.1.351.150.24.1.1.2 | NodevismTonePlanTableGrp | |||
| 1.3.6.1.4.1.351.150.24.1.1.2.1 | TablevismTonePlanTable | not-accessible | current | This table contains configuration information about different Tone Plans. The first 32 entries of the table are 'provisionable' followed by an implementation s… |
| 1.3.6.1.4.1.351.150.24.1.1.2.1.1 | RowvismTonePlanEntry | not-accessible | current | An entry in the vismTonePlanTable. Each entry consists of configuration information for a specific Tone Plan. The vismTonePlanTable is of fixed size with a pre… |
| 1.3.6.1.4.1.351.150.24.1.1.2.1.1.1 | ColumntonePlanIndex | not-accessible | current | Serves as index to this table. However, the maximum entry allowed is specify in tonePlanCurrentSize. |
| 1.3.6.1.4.1.351.150.24.1.1.2.1.1.2 | ColumntonePlanEntryStatus | read-write | current | This attribute specifies the status of this entry as to whether this entry (row) contains usable Tone Plan configuration information (object is set to 'configu… |
| 1.3.6.1.4.1.351.150.24.1.1.2.1.1.3 | ColumntonePlanProvisionFlag | read-only | current | This attribute specifies whether this entry contains predefined Tone Plan configuration information from internal firmware code (object is set to 'builtIn') or… |
| 1.3.6.1.4.1.351.150.24.1.1.2.1.1.4 | ColumntonePlanRegionName | read-write | current | The region (or country) for which this tone plan is defined. Any other entry in this table may have an identical name, but the combination of tonePlanRegionNam… |
| 1.3.6.1.4.1.351.150.24.1.1.2.1.1.5 | ColumntonePlanVersionNumber | read-write | current | This attribute specifies this entry's version number for a tone plan for a region. Multiple tone plans may be defined for each region, but each of these tone p… |
| 1.3.6.1.4.1.351.150.24.1.1.2.1.1.6 | ColumntonePlanFileName | read-write | current | This is the name of a valid file stored on the TFTP server which contains the tone definitions. A missing or invalid file name will cause a failure in the conf… |
| 1.3.6.1.4.1.351.150.24.1.1.3 | NodevismConfigToneDetectGrp | |||
| 1.3.6.1.4.1.351.150.24.1.1.3.1 | TablevismConfigToneDetectTable | not-accessible | current | This table contains the list of user configurable dual frequency tones that can be detected on VISM. The call agent can request the VISM to detect any of the t… |
| 1.3.6.1.4.1.351.150.24.1.1.3.1.1 | RowvismConfigToneDetectEntry | not-accessible | current | This is the primary entry in the vismConfigToneDetectTable. Each entry references a User configurable dual frequency tones that can be detected on VISM. |
| 1.3.6.1.4.1.351.150.24.1.1.3.1.1.1 | ColumnvismConfigToneDetectNum | read-only | current | This is the index of this table. Currently only tones 1 to 10 are used and call agent can request up to ten tones to be detected on different endpoints at any … |
| 1.3.6.1.4.1.351.150.24.1.1.3.1.1.2 | ColumnvismEventCode | read-create | current | This is the secondary index of this table. Call agent can request supervision tone detection indexed by this field. The values of event code are mapped from th… |
| 1.3.6.1.4.1.351.150.24.1.1.3.1.1.3 | ColumnvismConfigToneDetectRowStatus | read-create | current | Controls the creation and deletion of a Config Tone. An entry may be created using the 'createAndGo' option. When the row is successfully created, the vismConf… |
| 1.3.6.1.4.1.351.150.24.1.1.3.1.1.4 | ColumnvismFreqMaxDeviation | read-create | current | Specifies the maximum frequency deviation to be used by VISM when detecting a specific dual frequency tone. Please refer the VISM configuration guide for stand… |
| 1.3.6.1.4.1.351.150.24.1.1.3.1.1.5 | ColumnvismFreqMaxPower | read-create | current | Specifies the maximum frequency power to be used by VISM when detecting a specific dual frequency tone. Please refer the VISM configuration guide for standard … |
| 1.3.6.1.4.1.351.150.24.1.1.3.1.1.6 | ColumnvismFreqMinPower | read-create | current | Specifies the minimum frequency power to be used by VISM when detecting a specific dual frequency tone. Please refer the VISM configuration guide for standard … |
| 1.3.6.1.4.1.351.150.24.1.1.3.1.1.7 | ColumnvismFreqPowerTwist | read-create | current | Specifies the maximum frequency power twist permitted between the two frequencies used by VISM when detecting a dual frequency tone. Please refer the VISM conf… |
| 1.3.6.1.4.1.351.150.24.1.1.3.1.1.8 | ColumnvismFreqMaxDelay | read-create | current | Specifies the maximum frequency delay to be used by VISM when detecting a dual frequency tone. Please refer the VISM configuration guide for standard values to… |
| 1.3.6.1.4.1.351.150.24.1.1.3.1.1.9 | ColumnvismMinOnCadence | read-create | current | Specifies the minimum tone cycle ON time that is necessary for the VISM to detect the dual frequency tone. The vismMinOnCadence has to be less than vismFreqOnC… |
| 1.3.6.1.4.1.351.150.24.1.1.3.1.1.10 | ColumnvismMaxOffCadence | read-create | current | Specifies the maximum tone cycle OFF time that is necessary for the VISM to detect the dual frequency tone. The vismMaxOffCadence should be greater than vismFr… |
| 1.3.6.1.4.1.351.150.24.1.1.3.1.1.11 | ColumnvismFreqNumOfCadenceMatch | read-create | current | Specifies the number of pairs of the dual frequency that needs to be detected. Currently ten pairs of frequency can be detected by the DSP. |
| 1.3.6.1.4.1.351.150.24.1.1.3.1.1.12 | ColumnvismFrequency1 | read-create | current | Specifies the 1st frequency component of the dual frequency to be detected by the VISM. |
| 1.3.6.1.4.1.351.150.24.1.1.3.1.1.13 | ColumnvismFrequency2 | read-create | current | Specifies the 2nd frequency component of the dual frequency to be detected by the DSP. A value of 0 means this is a single frequency. The range of 1 to 279 is … |
| 1.3.6.1.4.1.351.150.24.1.1.3.1.1.14 | ColumnvismFreqOnCadence | read-create | current | The On time in each cycle of the dual frequency to be detected by the DSP. The vismFreqOnCadence has to be less than vismMinOnCadence value. It is measured in … |
| 1.3.6.1.4.1.351.150.24.1.1.3.1.1.15 | ColumnvismFreqOffCadence | read-create | current | The Off time in each cycle of the dual frequency to be detected by the DSP. The vismFreqOffCadence should be lesser than the vismMaxOffCadence value. It is mea… |
| 1.3.6.1.4.1.351.150.24.1.1.4 | NodevismSequentialToneDetectGrp | |||
| 1.3.6.1.4.1.351.150.24.1.1.4.1 | ScalarseqToneNumOfFrequencies | read-write | current | The number of single frequencies which have to be detected by the sequential tone detector command on VISM. The frequencies should specified below (seqToneFreq… |
| 1.3.6.1.4.1.351.150.24.1.1.4.2 | ScalarseqToneEventID | read-write | current | The eventID corresponding to the sequential frequency. Currently only supports Event 74 (SIT tone) |
| 1.3.6.1.4.1.351.150.24.1.1.4.3 | ScalarseqToneDurationOfEachTone | read-write | current | Nominal tone duration of each single tone in counts of 10ms used with sequential tone detector on VISM DSP. |
| 1.3.6.1.4.1.351.150.24.1.1.4.4 | ScalarseqToneGapBetweenEachTone | read-write | current | Nominal silence gap duration between each tone in 10ms used with sequential tone detector on VISM DSP. |
| 1.3.6.1.4.1.351.150.24.1.1.4.5 | ScalarseqToneDurationDeviation | read-write | current | Tone duration deviation allowed in 10ms used with sequential tone detector on VISM DSP. |
| 1.3.6.1.4.1.351.150.24.1.1.4.6 | ScalarseqToneMaximumGapDuration | read-write | current | Maximum tone duration allowed in 10ms used with sequential tone detector on VISM DSP. |
| 1.3.6.1.4.1.351.150.24.1.1.4.7 | ScalarseqToneGapDurationDeviation | read-write | current | Tone duration deviation allowed in 10ms used with sequential tone detector on VISM DSP. |
| 1.3.6.1.4.1.351.150.24.1.1.4.8 | ScalarseqToneFreqDeviation | read-write | current | Frequency deviation allowed (1 - 1000 Hz) used with sequential tone detector on VISM DSP. |
| 1.3.6.1.4.1.351.150.24.1.1.4.9 | ScalarseqTonePowerLevelCeiling | read-write | current | Maximum ceiling power level of the sequential frequency tone (absolute value in dBm) used with sequential tone detector on VISM DSP. Range from 0 to 40 (0 to -… |
| 1.3.6.1.4.1.351.150.24.1.1.4.10 | ScalarseqTonePowerLevelFloor | read-write | current | Lowest (floor) power level of the sequential frequency tone (absolute value in dBm) used with sequential tone detector on VISM DSP. Range from 0 to 40 (0 to -4… |
| 1.3.6.1.4.1.351.150.24.1.1.4.11 | ScalarseqToneFrequency1 | read-write | current | 1st frequency in the SequentialTone to detect (280 - 3800), used with sequential tone detector on VISM DSP. |
| 1.3.6.1.4.1.351.150.24.1.1.4.12 | ScalarseqToneFrequency2 | read-write | current | 2nd frequency in the SequentialTone to detect (280 - 3800), used with sequential tone detector on VISM DSP. |
| 1.3.6.1.4.1.351.150.24.1.1.4.13 | ScalarseqToneFrequency3 | read-write | current | 3rd frequency in the SequentialTone to detect (280 - 3800), used with sequential tone detector on VISM DSP. |
| 1.3.6.1.4.1.351.150.24.1.1.4.14 | ScalarseqToneFrequency4 | read-write | current | 4th frequency in the SequentialTone to detect (280 - 3800), used with sequential tone detector on VISM DSP. |
| 1.3.6.1.4.1.351.150.24.1.1.4.15 | ScalarseqToneFrequency5 | read-write | current | 5th frequency in the SequentialTone to detect (280 - 3800), used with sequential tone detector on VISM DSP. |
| 1.3.6.1.4.1.351.150.24.1.1.4.16 | ScalarseqToneFrequency6 | read-write | current | 6th frequency in the SequentialTone to detect (280 - 3800), used with sequential tone detector on VISM DSP. |
| 1.3.6.1.4.1.351.150.24.1.1.4.17 | ScalarseqToneFrequency7 | read-write | current | 7th frequency in the SequentialTone to detect (280 - 3800), used with sequential tone detector on VISM DSP. |
| 1.3.6.1.4.1.351.150.24.1.1.4.18 | ScalarseqToneFrequency8 | read-write | current | 8th frequency in the SequentialTone to detect (280 - 3800), used with sequential tone detector on VISM DSP. |
| 1.3.6.1.4.1.351.150.24.1.1.4.19 | ScalarseqToneFrequency9 | read-write | current | 9th frequency in the SequentialTone to detect (280 - 3800), used with sequential tone detector on VISM DSP. |
| 1.3.6.1.4.1.351.150.24.1.1.4.20 | ScalarseqToneFrequency10 | read-write | current | 10th frequency in the SequentialTone to detect (280 - 3800), used with sequential tone detector on VISM DSP. |
| 1.3.6.1.4.1.351.150.24.2 | NodevismToneNotificationPrefix | |||
| 1.3.6.1.4.1.351.150.24.2.0 | NodevismToneNotifications | |||
| 1.3.6.1.4.1.351.150.24.3 | NodevismTonePlanMIBConformance | |||
| 1.3.6.1.4.1.351.150.24.3.1 | NodevismTonePlanMIBCompliances | |||
| 1.3.6.1.4.1.351.150.24.3.1.1 | CompliancevismTonePlanMIBCompliance | current | The complaince statement for VISM Tone Plan group which implements vismTonePlanGrp MIB. | |
| 1.3.6.1.4.1.351.150.24.3.2 | NodevismTonePlanMIBGroups | |||
| 1.3.6.1.4.1.351.150.24.3.2.1 | GroupvismTonePlanControlGroup | current | This group contains objects related to control of VISM Tone Plan Table. | |
| 1.3.6.1.4.1.351.150.24.3.2.2 | GroupvismTonePlanTableGroup | current | This group contains objects related to configuration of VISM Tone Plan. | |
| 1.3.6.1.4.1.351.150.24.3.2.3 | GroupvismConfigToneDetectTableGroup | current | This group contains objects related to configuration of VISM dual frequency detect tones. | |
| 1.3.6.1.4.1.351.150.24.3.2.4 | GroupvismSequentialToneDetectGroup | current | This group contains objects related to configuration of VISM sequential single frequency tone detection. |