CME-MIB
2352 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | enterprises IpAddress |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2 | Nodeibm | |||
| 1.3.6.1.4.1.2.3 | NodeibmAgents | |||
| 1.3.6.1.4.1.2.3.51 | NodenetfinitySupportProcessorAgent | |||
| 1.3.6.1.4.1.2.3.51.2 | NodebladeCenterSnmpMIB | |||
| 1.3.6.1.4.1.2.3.51.2.2 | Nodemonitors | |||
| 1.3.6.1.4.1.2.3.51.2.2.1 | Nodetemperature | |||
| 1.3.6.1.4.1.2.3.51.2.2.1.1 | NodeinternalTemp | |||
| 1.3.6.1.4.1.2.3.51.2.2.1.1.2 | ScalarcmmTemp | read-only | deprecated | This field is deprecated. The return value of this field is the same as rearLEDCardTemp. Chassis management module temperature in degrees centigrade(C). An oct… |
| 1.3.6.1.4.1.2.3.51.2.2.1.5 | NodeambientTemp | |||
| 1.3.6.1.4.1.2.3.51.2.2.1.5.1 | ScalarrearLEDCardTempAvg | read-only | mandatory | The average rear LED card temperature in degrees centigrade(C). This is surrounding temperature where the system is installed. An octet string expressed as 'sd… |
| 1.3.6.1.4.1.2.3.51.2.2.1.5.2 | ScalarrearLEDCardTempMin | read-only | mandatory | The minimum rear LED card temperature in degrees centigrade(C). This is surrounding temperature where the system is installed. An octet string expressed as 'sd… |
| 1.3.6.1.4.1.2.3.51.2.2.1.5.3 | ScalarrearLEDCardTempMax | read-only | mandatory | The maximum rear LED card temperature in degrees centigrade(C). This is surrounding temperature where the system is installed. An octet string expressed as 'sd… |
| 1.3.6.1.4.1.2.3.51.2.2.1.9 | NodemonitorTemp | |||
| 1.3.6.1.4.1.2.3.51.2.2.1.9.3 | ScalarhotAirRecircMonitoring | read-write | mandatory | If this is enabled, the management module will monitor for Hot Air Recirculation by detecting non-uniform air temperature(s) that may be entering the front of … |
| 1.3.6.1.4.1.2.3.51.2.2.1.9.5 | ScalarhotAirRecircTempDeltaThresh | read-write | mandatory | This object is used to read or change the temperature delta threshold for Hot Air Recirculation detection. Values are enforced to be in the inclusive range bet… |
| 1.3.6.1.4.1.2.3.51.2.2.1.9.7 | TablehotAirRecircStatusTable | not-accessible | mandatory | Table of hot air recirculation status information. |
| 1.3.6.1.4.1.2.3.51.2.2.1.9.7.1 | RowhotAirRecircStatusEntry | not-accessible | mandatory | Hot air recirculation status entry |
| 1.3.6.1.4.1.2.3.51.2.2.1.9.7.1.2 | ColumnhotAirRecircStatusTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.2.1.9.7.1.3 | ColumnhotAirRecircStatusIndex | read-only | mandatory | Each component may have one or more sensor associated with it, this index object identifies the particular instance. |
| 1.3.6.1.4.1.2.3.51.2.2.1.9.7.1.4 | ColumnhotAirRecircStatusName | read-only | mandatory | The name of the component as a null terminated string |
| 1.3.6.1.4.1.2.3.51.2.2.1.9.7.1.5 | ColumnhotAirRecircStatusSensorLabel | read-only | mandatory | The text label of the sensor as a null terminated string |
| 1.3.6.1.4.1.2.3.51.2.2.1.9.7.1.6 | ColumnhotAirRecircStatusSensorReading | read-only | mandatory | Ambient temperature reading for this component in degrees centigrade(C). The string is formatted as 'dd.dd Centigrade'. |
| 1.3.6.1.4.1.2.3.51.2.2.1.9.7.1.7 | ColumnhotAirRecircStatusExceeded | read-only | mandatory | Indicates whether this component has exceeded the threshold of the acceptable temperature being monitored for hot air recirculation. |
| 1.3.6.1.4.1.2.3.51.2.2.3 | NodechassisFans | |||
| 1.3.6.1.4.1.2.3.51.2.2.3.50 | TablechassisFansTable | not-accessible | mandatory | Table of chassis Fan information. |
| 1.3.6.1.4.1.2.3.51.2.2.3.50.1 | RowchassisFansEntry | not-accessible | mandatory | Chassis Fan information entry |
| 1.3.6.1.4.1.2.3.51.2.2.3.50.1.1 | ColumnchassisFanIndex | read-only | mandatory | Chassis Fans table index. |
| 1.3.6.1.4.1.2.3.51.2.2.3.50.1.2 | ColumnchassisFanId | read-only | mandatory | The numeric chassis fan ID. |
| 1.3.6.1.4.1.2.3.51.2.2.3.50.1.3 | ColumnchassisFanSpeed | read-only | mandatory | Chassis fan speed expressed in percent(%) of maximum RPM. An octet string expressed as 'ddd% of maximum' where: d is a decimal digit or blank space for a leadi… |
| 1.3.6.1.4.1.2.3.51.2.2.3.50.1.4 | ColumnchassisFanState | read-only | mandatory | The health state for the chassis fan. Note that the other UIs may use slightly different terminology for the three health state values, as such: WEB - Normal, … |
| 1.3.6.1.4.1.2.3.51.2.2.3.50.1.5 | ColumnchassisFanSpeedRPM | read-only | mandatory | Chassis fan speed expressed in RPM. If the chassis fan is determined not to be running or the chassis fan speed cannot be determined, the string will indicate … |
| 1.3.6.1.4.1.2.3.51.2.2.3.50.1.6 | ColumnchassisFanControllerState | read-only | mandatory | The controller health state for the chassis fan. |
| 1.3.6.1.4.1.2.3.51.2.2.3.50.1.7 | ColumnchassisFanCoolingZone | read-only | mandatory | The cooling zone for the chassis fan. |
| 1.3.6.1.4.1.2.3.51.2.2.3.51 | TablechassisCoolingZoneTable | not-accessible | mandatory | Table of chassis cooling zone information. |
| 1.3.6.1.4.1.2.3.51.2.2.3.51.1 | RowchassisCoolingZoneEntry | not-accessible | mandatory | Chassis cooling zone information entry |
| 1.3.6.1.4.1.2.3.51.2.2.3.51.1.1 | ColumnchassisCoolingIndex | read-only | mandatory | Chassis Cooling Zones table index. |
| 1.3.6.1.4.1.2.3.51.2.2.3.51.1.2 | ColumnchassisCoolingZone | read-only | mandatory | The cooling zone for the chassis component. |
| 1.3.6.1.4.1.2.3.51.2.2.3.51.1.3 | ColumnchassisCoolingZoneStatus | read-only | mandatory | The health state of the chassis cooling zone. Note: This is the health of the cooling zone, not the health status of the component in chassisCoolingZoneCompone… |
| 1.3.6.1.4.1.2.3.51.2.2.3.51.1.4 | ColumnchassisCoolingZoneComponent | read-only | mandatory | A component within a cooling zone. |
| 1.3.6.1.4.1.2.3.51.2.2.4 | NodepowerModuleHealth | |||
| 1.3.6.1.4.1.2.3.51.2.2.4.1 | TablepowerModuleHealthTable | not-accessible | mandatory | Table of power module health information. Contains the power health information for each power module. |
| 1.3.6.1.4.1.2.3.51.2.2.4.1.1 | RowpowerModuleHealthEntry | not-accessible | mandatory | Power Module health entry |
| 1.3.6.1.4.1.2.3.51.2.2.4.1.1.1 | ColumnpowerModuleIndex | read-only | mandatory | Power module index. |
| 1.3.6.1.4.1.2.3.51.2.2.4.1.1.2 | ColumnpowerModuleExists | read-only | mandatory | Indicates whether the power module specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.2.4.1.1.3 | ColumnpowerModuleState | read-only | mandatory | The health state for the power module. Note that the other UIs may use slightly different terminology for the three health state values, as such: WEB - Normal,… |
| 1.3.6.1.4.1.2.3.51.2.2.4.1.1.4 | ColumnpowerModuleDetails | read-only | mandatory | The details for this power module. |
| 1.3.6.1.4.1.2.3.51.2.2.4.1.1.9 | ColumnpowerModuleDescription | read-only | mandatory | The description for this power module. |
| 1.3.6.1.4.1.2.3.51.2.2.5 | NodespStatus | |||
| 1.3.6.1.4.1.2.3.51.2.2.5.2 | NodemmBistAndChassisStatus | |||
| 1.3.6.1.4.1.2.3.51.2.2.5.2.5 | ScalarbistRtc | read-only | mandatory | MM BIST Real Time Clock test result. |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.7 | ScalarbistLocalI2CBus | read-only | mandatory | MM BIST Local I2C bus test result. |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.8 | ScalarbistPrimaryMainAppFlashImage | read-only | mandatory | MM BIST Primary Main Application Firmware test result. |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.9 | ScalarbistSecondaryMainAppFlashImage | read-only | mandatory | MM BIST Secondary Main Application test result. |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.10 | ScalarbistBootRomFlashImage | read-only | mandatory | MM BIST Boot Firmware test result. |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.11 | ScalarbistEthernetPort1 | read-only | mandatory | MM BIST external eth0 ethernet port test result. |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.14 | ScalarbistExternalI2CDevices | read-only | mandatory | MM BIST external I2C devices test result. |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.19 | ScalarbistInternalEthernetSwitch | read-only | mandatory | MM BIST internal external switch test result. |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.25 | ScalarbistPrimaryKernel | read-only | mandatory | MM BIST primary kernel test result. |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.26 | ScalarbistSecondaryKernel | read-only | mandatory | MM BIST secondary kernel test result. |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.29 | ScalarbistPhysicalNetworkLink | read-only | mandatory | MM BIST Physical Network Link test result. |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.30 | ScalarbistLogicalNetworkLink | read-only | mandatory | MM BIST Logical Network Link test result. |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.33 | ScalarbistBladesInstalled | read-only | mandatory | The blades that are installed on the chassis. The blades are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the… |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.49 | ScalarbistBladesCommunicating | read-only | mandatory | The blades that are communicating on the chassis. The blades are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as… |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.65 | ScalarbistChassisFansInstalled | read-only | mandatory | The chassis fans that are installed on the chassis. They are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the… |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.73 | ScalarbistChassisFansFunctional | read-only | mandatory | The chassis fans installed on the chassis that are functional. They are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as … |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.74 | ScalarbistRearLEDCardInstalled | read-only | mandatory | Indicates whether a rear LED card is installed |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.75 | ScalarbistRearLEDCardCommunicating | read-only | mandatory | Indicates whether a rear LED card is communicating |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.76 | ScalarbistOtherMMInstalled | read-only | mandatory | Indicates whether a redundant MM is installed. |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.77 | ScalarbistOtherMMCommunicating | read-only | mandatory | Indicates whether a redundant MM is communicating. |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.81 | ScalarbistPowerModulesInstalled | read-only | mandatory | The power modules that are installed on the chassis. The power modules are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is … |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.89 | ScalarbistPowerModulesFunctional | read-only | mandatory | The power modules that are functional on the chassis. The power modules are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is… |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.97 | ScalarbistSwitchModulesInstalled | read-only | mandatory | The switch modules that are installed on the chassis. The switch modules are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that i… |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.113 | ScalarbistSwitchModulesCommunicating | read-only | mandatory | The switch modules that are communicating on the chassis. The switch modules are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's th… |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.120 | ScalarbistChassisFansMUXAInstalled | read-only | mandatory | Indicates whether chassis fan MUX A is installed |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.121 | ScalarbistChassisFansMUXAFunctional | read-only | mandatory | Indicates whether chassis fan MUX A is functional |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.122 | ScalarbistChassisFansMUXBInstalled | read-only | mandatory | Indicates whether chassis fan MUX B is installed |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.123 | ScalarbistChassisFansMUXBFunctional | read-only | mandatory | Indicates whether chassis fan MUX B is functional |
| 1.3.6.1.4.1.2.3.51.2.2.5.2.200 | ScalarbistLastUpdate | read-only | mandatory | It is the time when the primary MM updated the last BIST results. |
| 1.3.6.1.4.1.2.3.51.2.2.5.3 | NodermmBistAndChassisStatus | |||
| 1.3.6.1.4.1.2.3.51.2.2.5.3.5 | ScalarrbistRtc | read-only | mandatory | Standby MM BIST Real Time Clock test result. The time of the last update can be obtained by querying rbistUpdateTime object. |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.7 | ScalarrbistLocalI2CBus | read-only | mandatory | Standby MM BIST Local I2C bus test result. The time of the last update can be obtained by querying rbistUpdateTime object. |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.11 | ScalarrbistEthernetPort1 | read-only | mandatory | Standby MM BIST external ethernet port test result. The time of the last update can be obtained by querying rbistUpdateTime object. |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.14 | ScalarrbistExternalI2CDevices | read-only | mandatory | Standby MM BIST external I2C devices test result collected when the standby MM was primary. The time of the last update can be obtained by querying rbistUpdate… |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.19 | ScalarrbistInternalEthernetSwitch | read-only | mandatory | Standby MM BIST internal external switch test result. The time of the last update can be obtained by querying rbistUpdateTime object. |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.29 | ScalarrbistPhysicalNetworkLink | read-only | mandatory | Standby MM BIST Physical Network Link test result collected when the standby MM was primary. The time of the last update can be obtained by querying rbistUpdat… |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.30 | ScalarrbistLogicalNetworkLink | read-only | mandatory | Standby MM BIST Logical Network Link test result collected when the standby MM was primary. The time of the last update can be obtained by querying rbistUpdate… |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.33 | ScalarrbistBladesInstalled | read-only | mandatory | The blades that were installed on the chassis when the standby MM was once primary. The time of the last update can be obtained by querying rbistUpdateTimePrim… |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.49 | ScalarrbistBladesCommunicating | read-only | mandatory | The blades that were communicating on the chassis when the standby MM was once primary. The time of the last update can be obtained by querying rbistUpdateTime… |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.65 | ScalarrbistChassisFansInstalled | read-only | mandatory | The chassis fans that were installed on the chassis when the standby MM was once primary. The time of the last update can be obtained by querying rbistUpdateTi… |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.73 | ScalarrbistChassisFansFunctional | read-only | mandatory | The chassis fans installed on the chassis that were functional when the standby MM was once primary. The time of the last update can be obtained by querying rb… |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.74 | ScalarrbistRearLEDCardInstalled | read-only | mandatory | Indicates whether a rear LED card is installed |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.75 | ScalarrbistRearLEDCardCommunicating | read-only | mandatory | Indicates whether a rear LED card is communicating |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.76 | ScalarrbistOtherMMInstalled | read-only | mandatory | Indicates whether a standby MM was installed when the standby MM was once primary.The time of the last update can be obtained by querying rbistUpdateTimePrimar… |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.77 | ScalarrbistOtherMMCommunicating | read-only | mandatory | Indicates whether a standby MM was communicating when the standby MM was once primary. The time of the last update can be gotten from the object 'rbistUpdateTi… |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.81 | ScalarrbistPowerModulesInstalled | read-only | mandatory | The power modules that were installed on the chassis when the standby MM was once primary. The time of the last update can be obtained by querying rbistUpdateT… |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.89 | ScalarrbistPowerModulesFunctional | read-only | mandatory | The power modules that were functional on the chassis when the standby MM was once primary. The time of the last update can be obtained by querying rbistUpdate… |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.97 | ScalarrbistSwitchModulesInstalled | read-only | mandatory | The switch modules that were installed on the chassis when the standby MM was once primary. The time of the last update can be obtained by querying rbistUpdate… |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.113 | ScalarrbistSwitchModulesCommunicating | read-only | mandatory | The switch modules that are communicating on the chassis when the standby MM was once primary. The time of the last update can be obtained by querying rbistUpd… |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.120 | ScalarrbistChassisFansMUXAInstalled | read-only | mandatory | Indicates whether chassis fan MUX A is installed |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.121 | ScalarrbistChassisFansMUXAFunctional | read-only | mandatory | Indicates whether chassis fan MUX A is functional |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.122 | ScalarrbistChassisFansMUXBInstalled | read-only | mandatory | Indicates whether chassis fan MUX B is installed |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.123 | ScalarrbistChassisFansMUXBFunctional | read-only | mandatory | Indicates whether chassis fan MUX B is functional |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.200 | ScalarrbistUpdateTime | read-only | mandatory | It is the time when the standby MM updated the last BIST results. |
| 1.3.6.1.4.1.2.3.51.2.2.5.3.201 | ScalarrbistLastUpdatePrimary | read-only | mandatory | It is the time when the standby MM updated the last BIST results when it was still primary. |
| 1.3.6.1.4.1.2.3.51.2.2.6 | NodefanPack | |||
| 1.3.6.1.4.1.2.3.51.2.2.6.1 | TablefanPackTable | not-accessible | mandatory | Table of fan pack information. Contains the information for each fan pack. NOTE: Fan packs are also referred to as Power Module Cooling Devices. |
| 1.3.6.1.4.1.2.3.51.2.2.6.1.1 | RowfanPackEntry | not-accessible | mandatory | Fan Pack entry |
| 1.3.6.1.4.1.2.3.51.2.2.6.1.1.1 | ColumnfanPackIndex | read-only | mandatory | Fan Pack sequence index. |
| 1.3.6.1.4.1.2.3.51.2.2.6.1.1.2 | ColumnfanPackExists | read-only | mandatory | Indicates whether the fan pack specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.2.6.1.1.3 | ColumnfanPackState | read-only | mandatory | The health state for the fan pack. Note that the other UIs may use slightly different terminology for the three health state values, as such: WEB - Normal, Att… |
| 1.3.6.1.4.1.2.3.51.2.2.6.1.1.4 | ColumnfanPackFanCount | read-only | mandatory | The number of fans in the fan pack. |
| 1.3.6.1.4.1.2.3.51.2.2.6.1.1.5 | ColumnfanPackAverageSpeed | read-only | mandatory | The average speed of all fans in the fan pack expressed in percent(%) of maximum RPM. If the fan pack is determined not to be running or the fan pack speed can… |
| 1.3.6.1.4.1.2.3.51.2.2.6.1.1.6 | ColumnfanPackAverageSpeedRPM | read-only | mandatory | The average speed of all fans in the fan pack expressed in RPM. If the fan pack is determined not to be running or the fan pack speed cannot be determined, the… |
| 1.3.6.1.4.1.2.3.51.2.2.6.1.1.7 | ColumnfanPackControllerState | read-only | mandatory | The health state for the controller for the fan pack. |
| 1.3.6.1.4.1.2.3.51.2.2.7 | NodesystemHealth | |||
| 1.3.6.1.4.1.2.3.51.2.2.7.1 | ScalarsystemHealthStat | read-only | mandatory | Indicates status of system health for the system in which the MM resides. Value of 'critical' indicates a severe error has occurred and the system may not be f… |
| 1.3.6.1.4.1.2.3.51.2.2.7.2 | TablesystemHealthSummaryTable | not-accessible | mandatory | Table of System Health summary. Contains more detailed information about the reasons for the overall system health status. |
| 1.3.6.1.4.1.2.3.51.2.2.7.2.1 | RowsystemHealthSummaryEntry | not-accessible | mandatory | System Health Summary entry |
| 1.3.6.1.4.1.2.3.51.2.2.7.2.1.1 | ColumnsystemHealthSummaryIndex | read-only | mandatory | System health summary index. |
| 1.3.6.1.4.1.2.3.51.2.2.7.2.1.2 | ColumnsystemHealthSummarySeverity | read-only | mandatory | System health summary severity. |
| 1.3.6.1.4.1.2.3.51.2.2.7.2.1.3 | ColumnsystemHealthSummaryDescription | read-only | mandatory | System health summary description. |
| 1.3.6.1.4.1.2.3.51.2.2.7.2.1.4 | ColumnsystemHealthSummaryDateTime | read-only | mandatory | System health summary date time. |
| 1.3.6.1.4.1.2.3.51.2.2.7.2.1.11 | ColumnsystemHealthSummaryAuxData | read-only | mandatory | System health summary auxilliary event data. If auxilliary event data is available, it is device-specific event data provided to the CMM by the device. |
| 1.3.6.1.4.1.2.3.51.2.2.7.2.1.12 | ColumnsystemHealthSummaryEventID | read-only | mandatory | System health summary event ID. |
| 1.3.6.1.4.1.2.3.51.2.2.8 | Nodeleds | |||
| 1.3.6.1.4.1.2.3.51.2.2.8.1 | NodefrontPanelLEDs | |||
| 1.3.6.1.4.1.2.3.51.2.2.8.1.1 | ScalarfaultLED | read-only | mandatory | Indicates whether the front panel system error LED is on or off. |
| 1.3.6.1.4.1.2.3.51.2.2.8.1.2 | ScalarcheckLogLED | read-write | mandatory | Indicates whether the front panel system information LED is on or off. For Write access, the LED can be turned off only. |
| 1.3.6.1.4.1.2.3.51.2.2.8.1.4 | ScalaridentifyLED | read-write | mandatory | Indicates whether the front panel identity LED is on or off. |
| 1.3.6.1.4.1.2.3.51.2.2.8.2 | NodebladeLEDs | |||
| 1.3.6.1.4.1.2.3.51.2.2.8.2.1 | TablebladeLEDsTable | not-accessible | mandatory | Table of blade status information. NOTE: Querying objects in this table may take significantly longer than normal, so it is recommended that the query timeout … |
| 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1 | RowbladeLEDsEntry | not-accessible | mandatory | Blade system status entry |
| 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1.1 | ColumnledBladeIndex | read-only | mandatory | Blade LED table index. |
| 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1.2 | ColumnledBladeId | read-only | mandatory | The numeric blade ID. |
| 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1.3 | ColumnledBladeExists | read-only | mandatory | Indicates whether the blade specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1.4 | ColumnledBladePowerState | read-only | mandatory | Indicates the power state of the blade specified. |
| 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1.5 | ColumnledBladeHealthState | read-only | mandatory | The system health state for the blade. Unknown: Blade is in an undefined state. Good: Blade is operating normally. Warning: One or more outstanding warnings ex… |
| 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1.6 | ColumnledBladeName | read-only | mandatory | The name of the blade as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1.7 | ColumnledBladeFault | read-only | mandatory | Indicates whether the blade fault LED is on or off. |
| 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1.8 | ColumnledBladeCheckLog | read-write | mandatory | Indicates whether the blade check log information LED is on or off. For Write access, the LED can be turned off only. |
| 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1.11 | ColumnledBladeIdentify | read-write | mandatory | Indicates whether the blade identify LED is on, off, or blinking. |
| 1.3.6.1.4.1.2.3.51.2.2.8.2.2 | TablebladeLEDsDetailsTable | not-accessible | mandatory | Table of blade LEDs detailed information. NOTE: Querying objects in this table may take significantly longer than normal, so it is recommended that the query t… |
| 1.3.6.1.4.1.2.3.51.2.2.8.2.2.1 | RowbladeLEDsDetailsEntry | not-accessible | mandatory | Blade LEDs Details entry |
| 1.3.6.1.4.1.2.3.51.2.2.8.2.2.1.1 | ColumnledIndex | read-only | mandatory | The LED index number. |
| 1.3.6.1.4.1.2.3.51.2.2.8.2.2.1.2 | ColumnledBladeBayNumber | read-only | mandatory | The bay number of the main server blade that the LED is grouped into. |
| 1.3.6.1.4.1.2.3.51.2.2.8.2.2.1.3 | ColumnledBladeComponentType | read-only | mandatory | Type of the component/subcomponent grouping for this LED. |
| 1.3.6.1.4.1.2.3.51.2.2.8.2.2.1.4 | ColumnledBladeLabel | read-only | mandatory | Text label for a LED. |
| 1.3.6.1.4.1.2.3.51.2.2.8.2.2.1.5 | ColumnledBladeState | read-only | mandatory | Text description which denotes color or on/off/blink state for a LED. |
| 1.3.6.1.4.1.2.3.51.2.2.8.2.2.1.6 | ColumnledBladeLocation | read-only | mandatory | Location of this LED. |
| 1.3.6.1.4.1.2.3.51.2.2.8.4 | NodesmLEDs | |||
| 1.3.6.1.4.1.2.3.51.2.2.8.4.2 | TablesmLEDsTable | not-accessible | mandatory | Table of switch module LEDs information. |
| 1.3.6.1.4.1.2.3.51.2.2.8.4.2.1 | RowsmLEDsEntry | not-accessible | mandatory | Switch module LEDs information entry |
| 1.3.6.1.4.1.2.3.51.2.2.8.4.2.1.1 | ColumnledSMIndex | read-only | mandatory | Switch module LEDs table index. |
| 1.3.6.1.4.1.2.3.51.2.2.8.4.2.1.2 | ColumnledSMSlot | read-only | mandatory | The bay number of the switch. |
| 1.3.6.1.4.1.2.3.51.2.2.8.4.2.1.3 | ColumnledSMLabel | read-only | mandatory | The name associated with the LED. |
| 1.3.6.1.4.1.2.3.51.2.2.8.4.2.1.4 | ColumnledSMState | read-write | mandatory | NOTE: This table entry is read-write ONLY when Label = 'Enclosure Identity'. All other Label values have read-only access. |
| 1.3.6.1.4.1.2.3.51.2.2.8.4.2.1.5 | ColumnledSMLocation | read-only | mandatory | The physical location where the LED can be found on the Switch. |
| 1.3.6.1.4.1.2.3.51.2.2.8.5 | NodechassisFanLEDs | |||
| 1.3.6.1.4.1.2.3.51.2.2.8.5.1 | TablechassisFanLEDsTable | not-accessible | mandatory | Table of chassis fan LEDs information. |
| 1.3.6.1.4.1.2.3.51.2.2.8.5.1.1 | RowchassisFanLEDsEntry | not-accessible | mandatory | Chassis fan LEDs information entry |
| 1.3.6.1.4.1.2.3.51.2.2.8.5.1.1.1 | ColumnledChassisFanIndex | read-only | mandatory | Chassis fan LEDs table index. |
| 1.3.6.1.4.1.2.3.51.2.2.8.5.1.1.2 | ColumnledChassisFanId | read-only | mandatory | The numeric chassis fan ID. |
| 1.3.6.1.4.1.2.3.51.2.2.8.5.1.1.3 | ColumnledChassisFanExists | read-only | mandatory | Indicates whether the chassis fan specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.2.8.5.1.1.4 | ColumnledChassisFanError | read-only | mandatory | Indicates whether the chassis fan error LED is on, off, or not available. |
| 1.3.6.1.4.1.2.3.51.2.2.8.6 | NodefanPackLEDs | |||
| 1.3.6.1.4.1.2.3.51.2.2.8.6.1 | TablefanPackLEDsTable | not-accessible | deprecated | Table of fan pack LEDs information. This table is deprecated because the LEDs for the power modules' fans are no longer on the fan packs, the LEDs are on the p… |
| 1.3.6.1.4.1.2.3.51.2.2.8.6.1.1 | RowfanPackLEDsEntry | not-accessible | deprecated | Fan Pack LEDs information entry |
| 1.3.6.1.4.1.2.3.51.2.2.8.6.1.1.1 | ColumnledFanPackIndex | read-only | deprecated | Fan Pack LEDs table index. |
| 1.3.6.1.4.1.2.3.51.2.2.8.6.1.1.2 | ColumnledFanPackId | read-only | deprecated | The numeric fan pack ID. |
| 1.3.6.1.4.1.2.3.51.2.2.8.6.1.1.3 | ColumnledFanPackExists | read-only | deprecated | Indicates whether the fan pack specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.2.8.6.1.1.4 | ColumnledFanPackError | read-only | deprecated | Indicates whether the fan pack error LED is on or off. |
| 1.3.6.1.4.1.2.3.51.2.2.10 | NodefuelGauge | |||
| 1.3.6.1.4.1.2.3.51.2.2.10.1 | NodefuelGaugeInformation | |||
| 1.3.6.1.4.1.2.3.51.2.2.10.1.1 | TablefuelGaugeTable | not-accessible | mandatory | Table of Fuel Gauge information. |
| 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1 | RowfuelGaugeEntry | not-accessible | mandatory | Fuel Gauge entry |
| 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.1 | ColumnfuelGaugeIndex | read-only | mandatory | Fuel Gauge Table Index. |
| 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.2 | ColumnfuelGaugePowerDomainNumber | read-only | mandatory | Fuel Gauge Table Power Domain Number. |
| 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.3 | ColumnfuelGaugeStatus | read-only | mandatory | Fuel Gauge Table Status for the power domain. The response will start out with a numeric value (0 = unknown, 1 = good, 2 = warning, and 3: bad), followed by a … |
| 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.4 | ColumnfuelGaugePowerModules | read-only | mandatory | Fuel Gauge Table Power Module capacity in Watts in the power domain. |
| 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.6 | ColumnfuelGaugePowerManagementPolicySetting | read-only | mandatory | Power Management Policy Setting for each power domain. A new powerPolicyTable has been added which provides more detailed information regarding a domains power… |
| 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.7 | ColumnfuelGaugeTotalPower | read-only | mandatory | This field displays the total available power for each power domain based on installed power modules and the current Power Management Policy Setting. |
| 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.8 | ColumnfuelGaugeAllocatedPower | read-only | mandatory | This field displays the power that has been reserved in each power domain. |
| 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.9 | ColumnfuelGaugeRemainingPower | read-only | mandatory | This field displays the remaining power available in each domain. Remaining Power = Total Power minus Power In Use |
| 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.10 | ColumnfuelGaugePowerInUsed | read-only | mandatory | This field displays the total power being used in each power domain. |
| 1.3.6.1.4.1.2.3.51.2.2.10.2 | NodepowerDomain1 | |||
| 1.3.6.1.4.1.2.3.51.2.2.10.2.1 | TablepowerDomain1Table | not-accessible | mandatory | Table of Power Domain 1. |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1 | RowpowerDomain1Entry | not-accessible | mandatory | Fuel Gauge entry |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.1 | Columnpd1Index | read-only | mandatory | Power Domain 1 Table Index. |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.2 | Columnpd1BayNumber | read-only | mandatory | Power Domain 1 Table Bay Number. The following Bay Number IDs are used: notApplicable(1), notApplicable(2), fanPackBay1(3), fanPackBay2(4), fanPackBay3(5), fan… |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.3 | Columnpd1BladePrimarySlot | read-only | mandatory | Power Domain 1 Table Blade Primary Slot can be useful when a server blade spans multiple slots (e.g. double wide or triple wide). For example if the blade is d… |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.4 | Columnpd1ModuleStatus | read-only | mandatory | Power Domain 1 Table Module Throttle Status. |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.5 | Columnpd1ModuleName | read-only | mandatory | Power Domain 1 Table Module Name. |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.6 | Columnpd1ModuleState | read-only | mandatory | Power Domain 1 Table Module State. |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.7 | Columnpd1ModuleAllocatedPowerCurrent | read-only | mandatory | Power Domain 1 Table Allocated Power Current indicates the current power allocation for the module in Watts. NOTE: When a server blade spans multiple slots (e.… |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.8 | Columnpd1ModuleAllocatedPowerMax | read-only | mandatory | Power Domain 1 Table Allocated Power Max indicates the maximum power allocation for the module in Watts. It is indicative of the maximum amount of power the mo… |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.9 | Columnpd1ModuleAllocatedPowerMin | read-only | mandatory | Power Domain 1 Table Allocated Power Min indicates the minumum power allocation for the module in Watts. It is indicative of the minumum power consumption of t… |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.10 | Columnpd1ModuleCPUDutyCycles | read-only | mandatory | Power Domain 1 Table Module CPUs Duty Cycles applies to blade servers only. It displays the duty cycle for each CPU on the blade as a percentage. Note that som… |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.11 | Columnpd1ModuleThrottle | read-only | mandatory | Power Domain 1 Table Module Throttle indicates whether the server blade may be allowed to throttle or not. |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.12 | Columnpd1ModulePowerCapabilities | read-only | mandatory | Power Domain 1 Table Module Power Capabilities. staticPowerManagement: the module with the static worst case power values. fixedPowermanagement: the module wit… |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.13 | Columnpd1ModuleMeasuredOrStatic | read-only | mandatory | Power Domain 1 Table Module Measured Or Static. |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.14 | Columnpd1TopologyPath | read-only | mandatory | The topology path for the component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the … |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.3 | NodepowerDomain1PowerTrending | |||
| 1.3.6.1.4.1.2.3.51.2.2.10.2.3.1 | Scalarpd1PowerTrendingPeriod | read-write | mandatory | Specify time period for power domain 1 power trending information table view. NOTE: This time period should be configured before displaying the following Power… |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.3.10 | Tablepd1PowerTrendingSampleTable | not-accessible | mandatory | Table of Power Domain 1 Power Trending Information. |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.3.10.1 | Rowpd1PowerTrendingSampleEntry | not-accessible | mandatory | Power Domain 1 Power Trending Sample entry. |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.3.10.1.1 | Columnpd1PowerTrendingSampleIndex | read-only | mandatory | Power Domain 1 Power Trending Sample Table Index. |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.3.10.1.2 | Columnpd1PowerTrendingSampleTimeStamp | read-only | mandatory | Power Domain 1 Power Trending Sample Table Timestamp. |
| 1.3.6.1.4.1.2.3.51.2.2.10.2.3.10.1.3 | Columnpd1PowerTrendingSampleAve | read-only | mandatory | Power Domain 1 Power Trending Table Average Power. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4 | NodemoduleInformation | |||
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1 | NodebladeDetails | |||
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1 | TablebladeDetailsTable | not-accessible | mandatory | Table of Blade Module Details. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1 | RowbladeDetailsEntry | not-accessible | mandatory | Blade Module Details entry. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.1 | ColumnbladeDetailsIndex | read-only | mandatory | Blade Module Details Table Index. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.2 | ColumnbladeDetailsId | read-only | mandatory | Blade Module Details Table Blade Id. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.3 | ColumnbladeDetailsMaxPowerConfig | read-write | mandatory | Blade Module Details Table Maximum Power Configuration. Allow the user to set the maximum power that can be used by the blade. This function is also known as p… |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.4 | ColumnbladeDetailsEffectiveClockRate | read-only | mandatory | Blade Module Details Table Effective CPU Clock Rate applies to DPM blades only. It displays processor's effective clock rate based on sample interval. Note tha… |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.5 | ColumnbladeDetailsMaximumClockRate | read-only | mandatory | Blade Module Details Table Maximum CPU Clock Rate applies to DPM blades only. It displays processor's maximum clock rate based on sample interval. Note that so… |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.6 | ColumnbladeDetailsPowerSaverMode | read-write | mandatory | When enabled, the static low power saver mode allows the blade to selectively alter its operating voltage and frequency to reduce power consumption. This featu… |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.7 | ColumnbladeDetailsDynamicPowerSaver | read-write | mandatory | When enabled, Dynamic Power Saver allows the voltage and frequency of the CPUs on the blade to be controlled based on how busy the CPU is. This feature is not … |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.8 | ColumnbladeDetailsDynamicPowerFavorPerformanceOverPower | read-write | mandatory | When enabled, Dynamic Power Favor Performance Over Power supports a max performance mode that pushes the system past its nominal CPU frequency when CPU and mem… |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.9 | ColumnbladeDetailsPowerControl | read-write | mandatory | This object is used to get or set the power control setting on a blade. If dynamic power mgmt is not supported on a blade, notApplicable(255) will be returned.… |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.10 | ColumnbladeDetailsPcapMin | read-only | mandatory | Blade Module Details Table power capping Minimum value in watts. The blade must support the advanced power management feature. If the value of Pcap Min is 'not… |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.11 | ColumnbladeDetailsPcapGuaranteedMin | read-only | mandatory | Blade Module Details Table power capping Guaranteed Minimum value in watts. The blade must support the advanced power management feature. If the value of Pcap … |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.12 | ColumnbladeDetailsPcapMax | read-only | mandatory | Blade Module Details Table power capping Maximum value in watts. The blade must support the advanced power management feature. If the value is '<max1> Watts,<m… |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3 | NodebladePowerTrending | |||
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.1 | ScalarbladePowerTrendingPeriod | read-write | mandatory | Specify time period for blade module power trending information table view. NOTE: This time period should be configured before displaying the following Power T… |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.2 | ScalarbladePowerTrendingBladeId | read-write | mandatory | Blade Module Power Trending Blade Id. NOTE: The Blade Id should be configured before displaying the bladePowerTrendingTable. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.3 | ScalarbladePowerTrendingTopologyPath | read-write | mandatory | |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.10 | TablebladePowerTrendingSampleTable | not-accessible | mandatory | Table of Blade Module Power Trending Information. Since the power trending data is constantly being computed and saved in the management application database, … |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.10.1 | RowbladePowerTrendingSampleEntry | not-accessible | mandatory | Blade Module Power Trending Sample entry. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.10.1.1 | ColumnbladePowerTrendingSampleIndex | read-only | mandatory | Blade Module Power Trending Sample Table Index. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.10.1.2 | ColumnbladePowerTrendingSampleId | read-only | mandatory | Blade Module Power Trending Sample Table Blade Id. If the blade is defined using a topology location by using the scalar bladePowerTrendingTopologyPath, a zero… |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.10.1.3 | ColumnbladePowerTrendingSampleTimeStamp | read-only | mandatory | Blade Module Power Trending Sample Table Timestamp. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.10.1.4 | ColumnbladePowerTrendingSampleMax | read-only | mandatory | Blade Module Power Trending Sample Table Maximum Power. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.10.1.5 | ColumnbladePowerTrendingSampleMin | read-only | mandatory | Blade Module Power Trending Sample Table Minimum Power. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.10.1.6 | ColumnbladePowerTrendingSampleAve | read-only | mandatory | Blade Module Power Trending Sample Table Average Power. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.10.1.7 | ColumnbladePowerTrendingSampleTopologyId | read-only | mandatory | Blade module topology path. This field will have a topology location when a blade is a storage blade or a blade defined with a sub chassis. If the blade is def… |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.2 | NodeswitchDetails | |||
| 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3 | NodeswitchPowerTrending | |||
| 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.1 | ScalarswitchPowerTrendingPeriod | read-write | mandatory | Specify time period for switch module power trending information table view. NOTE: This time period should be configured before displaying the following Power … |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.2 | ScalarswitchPowerTrendingSwitchId | read-write | mandatory | Switch Module Power Trending Switch Id. NOTE: The Switch Id should be configured before displaying the switchPowerTrendingTable. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.10 | TableswitchPowerTrendingSampleTable | not-accessible | mandatory | Table of Switch Module Power Trending Information. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.10.1 | RowswitchPowerTrendingSampleEntry | not-accessible | mandatory | Switch Module Power Trending Sample entry. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.10.1.1 | ColumnswitchPowerTrendingSampleIndex | read-only | mandatory | Switch Module Power Trending Sample Table Index. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.10.1.2 | ColumnswitchPowerTrendingSampleId | read-only | mandatory | Switch Module Power Trending Sample Table Switch Id. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.10.1.3 | ColumnswitchPowerTrendingSampleTimeStamp | read-only | mandatory | Switch Module Power Trending Sample Table Timestamp. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.10.1.4 | ColumnswitchPowerTrendingSampleMax | read-only | mandatory | Switch Module Power Trending Sample Table Maximum Power. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.10.1.5 | ColumnswitchPowerTrendingSampleMin | read-only | mandatory | Switch Module Power Trending Sample Table Minimum Power. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.10.1.6 | ColumnswitchPowerTrendingSampleAve | read-only | mandatory | Switch Module Power Trending Sample Table Average Power. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.3 | NodechassisFanDetails | |||
| 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3 | NodechassisFanPowerTrending | |||
| 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.1 | ScalarchassisFanPowerTrendingPeriod | read-write | mandatory | Specify time period for chassis fan module power trending information table view. NOTE: This time period should be configured before displaying the following P… |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.2 | ScalarchassisFanPowerTrendingId | read-write | mandatory | Chass fan mModule power trending fan ID. NOTE: The ID should be configured before displaying the chassisFanPowerTrendingTable. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.10 | TablechassisFanPowerTrendingSampleTable | not-accessible | mandatory | Table of chassis fan Module Power Trending Information. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.10.1 | RowchassisFanPowerTrendingSampleEntry | not-accessible | mandatory | Chassis fan Module Power Trending Sample entry. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.10.1.1 | ColumnchassisFanPowerTrendingSampleIndex | read-only | mandatory | Chassis fan Module Power Trending Sample Table Index. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.10.1.2 | ColumnchassisFanPowerTrendingSampleId | read-only | mandatory | Chassis fan Module Power Trending Sample Table Id. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.10.1.3 | ColumnchassisFanPowerTrendingSampleTimeStamp | read-only | mandatory | Chassis fan Module Power Trending Sample Table Timestamp. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.10.1.4 | ColumnchassisFanPowerTrendingSampleMax | read-only | mandatory | Chassis fan Module Power Trending Sample Table Maximum Power. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.10.1.5 | ColumnchassisFanPowerTrendingSampleMin | read-only | mandatory | Chassis fan Module Power Trending Sample Table Minimum Power. |
| 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.10.1.6 | ColumnchassisFanPowerTrendingSampleAve | read-only | mandatory | Chassis fan Module Power Trending Sample Table Average Power. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5 | NodechassisInformation | |||
| 1.3.6.1.4.1.2.3.51.2.2.10.5.1 | NodechassisConfiguration | |||
| 1.3.6.1.4.1.2.3.51.2.2.10.5.1.1 | ScalarchassisTotalDCPowerAvailable | read-only | mandatory | Chassis total DC power available, which displays the total DC power available for the entire chassis. It is the sum of the two power domains. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.1.2 | ScalarchassisTotalPowerInUsed | read-only | mandatory | Chassis total power being used, which displays the total power being consumed by all modules in the chassis. It also includes power consumed by the blowers (ch… |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.1.3 | ScalarchassisTotalThermalOutput | read-only | mandatory | Chassis total thermal output, which displays the thermal output (load) in BTUs per hour. It is calculated based on the total input power in use. (1 Watt = 3.41… |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.1.5 | ScalarchassisPowerService | read-only | deprecated | The chassis power service mode. NOTE: This MIB object is for BCS only. This object has been deprecated. See the object, powerModuleDescription, for similar inf… |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.3 | NodechassisPowerTrending | |||
| 1.3.6.1.4.1.2.3.51.2.2.10.5.3.1 | ScalarchassisPowerTrendingPeriod | read-write | mandatory | Specify time period of power trending information. NOTE: This time period should be configured before displaying the following Power Trending Information table… |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.3.10 | TablechassisPowerTrendingSampleTable | not-accessible | mandatory | Table of Chassis Power Trending Sample Information in specified time period. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.3.10.1 | RowchassisPowerTrendingSampleEntry | not-accessible | mandatory | Chassis Power Trending Sample entry in specified time period. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.3.10.1.1 | ColumnchassisPowerTrendingSampleIndex | read-only | mandatory | Chassis Power Trending Sample Index in specified time period. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.3.10.1.2 | ColumnchassisPowerTrendingSampleTimeStamp | read-only | mandatory | Chassis Power Trending Sample Timestamp in specified time period. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.3.10.1.3 | ColumnchassisPowerTrendingSampleAve | read-only | mandatory | Chassis Power Trending Sample Average Power in specified time period. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5 | NodechassisThermalTrending | |||
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.1 | ScalarchassisThermalTrendingPeriod | read-write | mandatory | Specify time period of thermal trending information. NOTE: This time period should be configured before displaying the following Thermal Trending Information t… |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.10 | TablerearLEDCardThermalTrendingTable | not-accessible | mandatory | Table of rear LED card Thermal Trending Information. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.10.1 | RowrearLEDCardThermalTrendingEntry | not-accessible | mandatory | Rear LED Card Thermal Trending entry. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.10.1.1 | ColumnrearLEDCardThermalTrendingIndex | read-only | mandatory | Rear LED Card Thermal Trending Table Index. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.10.1.2 | ColumnrearLEDCardThermalTrendingTimeStamp | read-only | mandatory | Rear LED Card Thermal Trending Table Sample Timestamp. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.10.1.3 | ColumnrearLEDCardThermalTrendingTemperatureAvg | read-only | mandatory | Rear LED Card Thermal Trending Table Average Temperature. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.10.1.4 | ColumnrearLEDCardThermalTrendingTemperatureMin | read-only | mandatory | Rear LED Card Thermal Trending Table Minumum Temperature. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.10.1.5 | ColumnrearLEDCardThermalTrendingTemperatureMax | read-only | mandatory | Rear LED Card Thermal Trending Table Maximum Temperature. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.60 | TablecfmThermalTrendingTable | not-accessible | mandatory | Table of Cubic Feet per Minute Thermal Trending Information. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.60.1 | RowcfmThermalTrendingEntry | not-accessible | mandatory | Chassis CFM Thermal Trending entry. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.60.1.1 | ColumncfmThermalTrendingIndex | read-only | mandatory | Cubic Feet per Minute Thermal Trending Table Index. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.60.1.2 | ColumncfmThermalTrendingTimeStamp | read-only | mandatory | Cubic Feet per Minute Thermal Trending Table Sample Timestamp. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.60.1.3 | ColumncfmThermalTrendingCurrentCFM | read-only | mandatory | Cubic Feet per Minute Thermal Trending Table The Current CFM of air flow calculated at this sample time. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.60.1.4 | ColumncfmThermalTrendingMaxCFM | read-only | mandatory | Cubic Feet per Minute Thermal Trending Table The Maximum CFM of air flow the chassis can provide at this sample time. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.70 | TableehiThermalTrendingTable | not-accessible | mandatory | Table of Exhaust Heat Index Thermal Trending Information. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.70.1 | RowehiThermalTrendingEntry | not-accessible | mandatory | Chassis Exhaust Heat Index Thermal Trending entry. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.70.1.1 | ColumnehiThermalTrendingIndex | read-only | mandatory | Exhaust Heat Index Thermal Trending Table Index. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.70.1.2 | ColumnehiThermalTrendingTimeStamp | read-only | mandatory | Chassis Exhaust Heat Index Thermal Trending Table Sample Timestamp. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.70.1.3 | ColumnehiThermalTrendingMinEHI | read-only | mandatory | Chassis Exhaust Heat Index Thermal Trending Table Minimum Exhaust Heat Index since last reboot. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.70.1.4 | ColumnehiThermalTrendingMaxEHI | read-only | mandatory | Chassis Exhaust Heat Index Thermal Trending Table Maximum Exhaust Heat Index since last reboot. |
| 1.3.6.1.4.1.2.3.51.2.2.10.5.5.70.1.5 | ColumnehiThermalTrendingAvgEHI | read-only | mandatory | Chassis Exhaust Heat Index Thermal Trending Table Average of last 2 Exhaust Heat Index calculations since last reboot. |
| 1.3.6.1.4.1.2.3.51.2.2.10.6 | NodepowerPolicyInformation | |||
| 1.3.6.1.4.1.2.3.51.2.2.10.6.1 | TablepowerPolicyTable | not-accessible | mandatory | Table of Power Policy information for all power domains. Reading this table can tell you about the available power policies that can be configured for a domain… |
| 1.3.6.1.4.1.2.3.51.2.2.10.6.1.1 | RowpowerPolicyEntry | not-accessible | mandatory | Power Policy Entry |
| 1.3.6.1.4.1.2.3.51.2.2.10.6.1.1.1 | ColumnpowerPolicyIndex | read-only | mandatory | The unique idenitifier of a row in the powerPolicyTable. |
| 1.3.6.1.4.1.2.3.51.2.2.10.6.1.1.2 | ColumnpowerPolicyPowerDomainNumber | read-only | mandatory | The power domain number which this row is associated with. |
| 1.3.6.1.4.1.2.3.51.2.2.10.6.1.1.3 | ColumnpowerPolicyName | read-only | mandatory | The short name of the power policy. The following are the possible names and their detailed description: Power Module Redundancy Intended for a single power so… |
| 1.3.6.1.4.1.2.3.51.2.2.10.6.1.1.4 | ColumnpowerPolicyPwrSupplyFailureLimit | read-only | mandatory | The maximum number of power supplies that can fail in a chassis while still providing redundancy. |
| 1.3.6.1.4.1.2.3.51.2.2.10.6.1.1.5 | ColumnpowerPolicyMaxPowerLimit | read-only | mandatory | The maximum power available (in watts), based on the number of power modules and the Power Management Policy setting. |
| 1.3.6.1.4.1.2.3.51.2.2.10.6.1.1.6 | ColumnpowerPolicyEstimatedUtilization | read-only | mandatory | The estimated utilization (as a percentage) based on current power usage. |
| 1.3.6.1.4.1.2.3.51.2.2.10.6.1.1.7 | ColumnpowerPolicyActivate | read-write | mandatory | When read, this object provides the status of this power policy. If the value is enabled(1), it means this is the active power policy for the associated domain… |
| 1.3.6.1.4.1.2.3.51.2.2.17 | Nodeusers | |||
| 1.3.6.1.4.1.2.3.51.2.2.17.1 | NodemmUsers | |||
| 1.3.6.1.4.1.2.3.51.2.2.17.1.1 | TablecurrentlyLoggedInTable | not-accessible | mandatory | Table of MM users currently logged in. |
| 1.3.6.1.4.1.2.3.51.2.2.17.1.1.1 | RowcurrentlyLoggedInEntry | not-accessible | mandatory | MM users currently logged in entries. |
| 1.3.6.1.4.1.2.3.51.2.2.17.1.1.1.1 | ColumncurrentlyLoggedInEntryIndex | read-only | mandatory | Index for MM users currently logged in. |
| 1.3.6.1.4.1.2.3.51.2.2.17.1.1.1.2 | ColumncurrentlyLoggedInEntryUserId | read-only | mandatory | Name for MM users currently logged in. NOTE: 'Default SNMPv1 user' indicates an internal user used by SNMPv1 agent. |
| 1.3.6.1.4.1.2.3.51.2.2.17.1.1.1.3 | ColumncurrentlyLoggedInEntryAccMethod | read-only | mandatory | Access method for MM users currently logged in. |
| 1.3.6.1.4.1.2.3.51.2.2.21 | NodevpdInformation | |||
| 1.3.6.1.4.1.2.3.51.2.2.21.1 | NodechassisInfoVpd | |||
| 1.3.6.1.4.1.2.3.51.2.2.21.1.1 | NodechassisVpd | |||
| 1.3.6.1.4.1.2.3.51.2.2.21.1.1.1 | ScalarchassisVpdMachineType | read-write | deprecated | Machine type VPD information (from System BIOS). This field must be four alpha numeric characters. |
| 1.3.6.1.4.1.2.3.51.2.2.21.1.1.2 | ScalarchassisVpdMachineModel | read-write | deprecated | Machine model VPD information (from System BIOS). This field must be three alpha numeric characters. |
| 1.3.6.1.4.1.2.3.51.2.2.21.1.1.3 | ScalarchassisSerialNumber | read-write | deprecated | Machine serial number VPD information (from System BIOS). This field must be seven alpha numeric characters. |
| 1.3.6.1.4.1.2.3.51.2.2.21.1.1.4 | ScalarchassisUUID | read-write | deprecated | Machine UUID (Universal Unique ID information) (from System BIOS). This field must be 32 alpha numeric characters. |
| 1.3.6.1.4.1.2.3.51.2.2.21.1.1.5 | ScalarchassisManufacturingId | read-only | deprecated | Machine chassis manufacturing ID. |
| 1.3.6.1.4.1.2.3.51.2.2.21.1.1.6 | ScalarchassisHardwareRevision | read-only | deprecated | Machine chassis hardware revision. If a hardware revision is programmed in the OEM VPD area for this component, then the HardwareRevisionString version of this… |
| 1.3.6.1.4.1.2.3.51.2.2.21.1.1.7 | ScalarchassisFruNumber | read-only | deprecated | Machine chassis FRU number. |
| 1.3.6.1.4.1.2.3.51.2.2.21.1.1.8 | ScalarchassisManufDate | read-only | deprecated | Machine chassis manufacture date. |
| 1.3.6.1.4.1.2.3.51.2.2.21.1.1.9 | ScalarchassisPartNumber | read-only | deprecated | Machine chassis part number. |
| 1.3.6.1.4.1.2.3.51.2.2.21.1.1.10 | ScalarchassisFruSerial | read-only | deprecated | Machine chassis FRU serial number. |
| 1.3.6.1.4.1.2.3.51.2.2.21.1.1.11 | ScalarchassisManufacturingIDNumber | read-only | deprecated | Machine chassis manufacturer ID Number. |
| 1.3.6.1.4.1.2.3.51.2.2.21.1.1.12 | ScalarchassisProductId | read-only | deprecated | Machine chassis product ID. |
| 1.3.6.1.4.1.2.3.51.2.2.21.1.1.13 | ScalarchassisSubManufacturerId | read-only | deprecated | Machine chassis subsystem manufacturer. |
| 1.3.6.1.4.1.2.3.51.2.2.21.1.1.14 | ScalarchassisClei | read-only | deprecated | Machine chassis Common Language Equipment Identification (CLEI). |
| 1.3.6.1.4.1.2.3.51.2.2.21.1.1.16 | ScalarchassisHardwareRevisionString | read-only | deprecated | Machine chassis hardware revision in string format. If a hardware revision is programmed in the OEM VPD area for this component, then this MIB object should be… |
| 1.3.6.1.4.1.2.3.51.2.2.21.2 | NodemmHardwareVpd | |||
| 1.3.6.1.4.1.2.3.51.2.2.21.2.1 | TablemmHardwareVpdTable | not-accessible | deprecated | Table of the management module hardware components. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1 | RowmmHardwareVpdEntry | not-accessible | deprecated | Management module hardware VPD entry. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.1 | ColumnmmHardwareVpdIndex | read-only | deprecated | Management module hardware VPD index. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.2 | ColumnmmHardwareVpdBayNumber | read-only | deprecated | Management module hardware VPD Bay number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.3 | ColumnmmHardwareVpdManufacturingId | read-only | deprecated | Management module hardware VPD manufacturing ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.4 | ColumnmmHardwareVpdFruNumber | read-only | deprecated | Management module hardware VPD FRU number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.5 | ColumnmmHardwareVpdHardwareRevision | read-only | deprecated | Management module hardware VPD hardware revision. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed i… |
| 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.6 | ColumnmmHardwareVpdUuid | read-only | deprecated | Management module hardware VPD UUID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.7 | ColumnmmHardwareVpdManufDate | read-only | deprecated | Management module hardware VPD manufacture date. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.8 | ColumnmmHardwareVpdPartNumber | read-only | deprecated | Management module hardware VPD Part number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.9 | ColumnmmHardwareVpdFruSerial | read-only | deprecated | Management module hardware VPD FRU serial number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.10 | ColumnmmHardwareVpdManufacturingIDNumber | read-only | deprecated | Management module hardware VPD manufacturer ID Number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.11 | ColumnmmHardwareVpdProductId | read-only | deprecated | Management module hardware VPD product ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.12 | ColumnmmHardwareVpdSubManufacturerId | read-only | deprecated | Management module hardware VPD subsystem manufacturer. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.13 | ColumnmmHardwareVpdClei | read-only | deprecated | Management module hardware VPD Common Language Equipment Identification (CLEI). For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.14 | ColumnmmHardwareVpdHardwareRevisionString | read-only | deprecated | Management module hardware VPD hardware revision in string format. For consistent results, view as a table and not as individual entries. If a hardware revisio… |
| 1.3.6.1.4.1.2.3.51.2.2.21.3 | NodemmFirmwareVpd | |||
| 1.3.6.1.4.1.2.3.51.2.2.21.3.1 | TablemmMainApplVpdTable | not-accessible | deprecated | Table of MM Firmware VPD. |
| 1.3.6.1.4.1.2.3.51.2.2.21.3.1.1 | RowmmMainApplVpdEntry | not-accessible | deprecated | MM Firmware VPD entry. |
| 1.3.6.1.4.1.2.3.51.2.2.21.3.1.1.1 | ColumnmmMainApplVpdIndex | read-only | deprecated | Firmware VPD index. |
| 1.3.6.1.4.1.2.3.51.2.2.21.3.1.1.2 | ColumnmmMainApplVpdName | read-only | deprecated | Firmware VPD name description. 'MM firmware' indicates the running firmware of the MM. 'MM firmware (pending restart)' indicates the flashed firmware of the MM… |
| 1.3.6.1.4.1.2.3.51.2.2.21.3.1.1.3 | ColumnmmMainApplVpdBuildId | read-only | deprecated | Firmware VPD build identification. |
| 1.3.6.1.4.1.2.3.51.2.2.21.3.1.1.4 | ColumnmmMainApplVpdRevisonNumber | read-only | deprecated | Firmware VPD revision number. |
| 1.3.6.1.4.1.2.3.51.2.2.21.3.1.1.5 | ColumnmmMainApplVpdFilename | read-only | deprecated | Firmware VPD file name. |
| 1.3.6.1.4.1.2.3.51.2.2.21.3.1.1.6 | ColumnmmMainApplVpdBuildDate | read-only | deprecated | Firmware VPD build date. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4 | NodebladeHardwareVpd | |||
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1 | TablebladeHardwareVpdTable | not-accessible | deprecated | Table of VPD information for the blade hardware components. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1 | RowbladeHardwareVpdEntry | not-accessible | deprecated | Blade hardware VPD entry. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.1 | ColumnbladeHardwareVpdIndex | read-only | deprecated | Blade hardware VPD index. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.2 | ColumnbladeHardwareVpdBayNumber | read-only | deprecated | Blade hardware VPD Bay number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.3 | ColumnbladeHardwareVpdManufacturingId | read-only | deprecated | Blade hardware VPD manufacturing ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.4 | ColumnbladeHardwareVpdFruNumber | read-only | deprecated | Blade hardware VPD FRU number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.5 | ColumnbladeHardwareVpdHardwareRevision | read-only | deprecated | Blade hardware VPD hardware revision. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the OEM VP… |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.6 | ColumnbladeHardwareVpdSerialNumber | read-only | deprecated | Blade hardware VPD serial number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.7 | ColumnbladeHardwareVpdMachineType | read-only | deprecated | Blade hardware VPD machine type. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.8 | ColumnbladeHardwareVpdUuid | read-only | deprecated | Blade hardware VPD UUID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.9 | ColumnbladeHardwareVpdManufDate | read-only | deprecated | Blade hardware VPD Manufacture Date. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.10 | ColumnbladeHardwareVpdPartNumber | read-only | deprecated | Blade hardware VPD Part number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.11 | ColumnbladeHardwareVpdFruSerial | read-only | deprecated | Blade hardware VPD FRU serial number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.12 | ColumnbladeHardwareVpdMachineModel | read-only | deprecated | Blade hardware VPD machine model. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.13 | ColumnbladeHardwareVpdManufacturingIDNumber | read-only | deprecated | Blade hardware VPD Manufacturer ID Number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.14 | ColumnbladeHardwareVpdProductId | read-only | deprecated | Blade hardware VPD product ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.15 | ColumnbladeHardwareVpdSubManufacturerId | read-only | deprecated | Blade hardware VPD subsystem manufacturer ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.16 | ColumnbladeHardwareVpdClei | read-only | deprecated | Blade hardware VPD Common Language Equipment Identifier (CLEI). For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.17 | ColumnbladeHardwareVpdHardwareRevisionString | read-only | deprecated | Blade hardware VPD hardware revision in string format. For consistent results, view as a table and not as individual entries. If a hardware revision is program… |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.20 | ColumnbladeDaughterVpdCardType | read-only | deprecated | Blade expansion card (daughter card) VPD type. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.21 | ColumnbladeDaughterVpdManufacturingId | read-only | deprecated | Blade expansion card (daughter card) VPD manufacturing ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.22 | ColumnbladeDaughterVpdFruNumber | read-only | deprecated | Blade expansion card (daughter card) VPD FRU number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.23 | ColumnbladeDaughterVpdHardwareRevision | read-only | deprecated | Blade expansion card (daughter card) VPD hardware revision. For consistent results, view as a table and not as individual entries. If a hardware revision is pr… |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.24 | ColumnbladeDaughterVpdSerialNumber | read-only | deprecated | Blade expansion card (daughter card) VPD Serial number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.25 | ColumnbladeDaughterVpdMachineType | read-only | deprecated | Blade expansion card (daughter card) VPD Machine type. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.26 | ColumnbladeDaughterVpdUuid | read-only | deprecated | Blade expansion card (daughter card) VPD UUID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.27 | ColumnbladeDaughterVpdManufDate | read-only | deprecated | Blade expansion card (daughter card) VPD Manufacture date. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.28 | ColumnbladeDaughterVpdPartNumber | read-only | deprecated | Blade expansion card (daughter card) VPD Part number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.29 | ColumnbladeDaughterVpdFruSerial | read-only | deprecated | Blade expansion card (daughter card) VPD FRU Serial. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.30 | ColumnbladeDaughterVpdManufacturingIDNumber | read-only | deprecated | Blade expansion card (daughter card) VPD manufacturer ID Number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.31 | ColumnbladeDaughterVpdProductId | read-only | deprecated | Blade expansion card (daughter card) VPD product ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.32 | ColumnbladeDaughterVpdSubManufacturerId | read-only | deprecated | Blade expansion card (daughter card) VPD subsystem manufacturing ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.33 | ColumnbladeDaughterVpdClei | read-only | deprecated | Blade expansion card (daughter card) VPD Common Language Equipment Identifier (CLEI). For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.34 | ColumnbladeDaughterVpdHardwareRevisionString | read-only | deprecated | Blade expansion card (daughter card) VPD hardware revision in string format. For consistent results, view as a table and not as individual entries. If a hardwa… |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2 | TablebladeMACAddressVpdTable | not-accessible | mandatory | Table of MAC addresses of the blade and its expansion cards (daughter cards). For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1 | RowbladeMACAddressVpdEntry | not-accessible | mandatory | Blade MAC address entry. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.1 | ColumnbladeMACAddressVpdIndex | read-only | mandatory | Blade index. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.2 | ColumnbladeMACAddress1Vpd | read-only | mandatory | Blade MAC address 1. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.3 | ColumnbladeMACAddress2Vpd | read-only | mandatory | Blade MAC address 2. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.4 | ColumnbladeMACAddress3Vpd | read-only | mandatory | Blade MAC address 3. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.5 | ColumnbladeMACAddress4Vpd | read-only | mandatory | Blade MAC address 4. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.6 | ColumnbladeMACAddress5Vpd | read-only | mandatory | Blade MAC address 5. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.7 | ColumnbladeMACAddress6Vpd | read-only | mandatory | Blade MAC address 6. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.8 | ColumnbladeMACAddress7Vpd | read-only | mandatory | Blade MAC address 7. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.9 | ColumnbladeMACAddress8Vpd | read-only | mandatory | Blade MAC address 8. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.10 | ColumnbladeDaughterCard1MACAddress1Vpd | read-only | mandatory | Blade expansion card (daughter card) 1 MAC address 1. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.11 | ColumnbladeDaughterCard1MACAddress2Vpd | read-only | mandatory | Blade expansion card (daughter card) 1 MAC address 2. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.12 | ColumnbladeDaughterCard1MACAddress3Vpd | read-only | mandatory | Blade expansion card (daughter card) 1 MAC address 3. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.13 | ColumnbladeDaughterCard1MACAddress4Vpd | read-only | mandatory | Blade expansion card (daughter card) 1 MAC address 4. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.14 | ColumnbladeDaughterCard1MACAddress5Vpd | read-only | mandatory | Blade expansion card (daughter card) 1 MAC address 5. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.15 | ColumnbladeDaughterCard1MACAddress6Vpd | read-only | mandatory | Blade expansion card (daughter card) 1 MAC address 6. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.16 | ColumnbladeDaughterCard1MACAddress7Vpd | read-only | mandatory | Blade expansion card (daughter card) 1 MAC address 7. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.17 | ColumnbladeDaughterCard1MACAddress8Vpd | read-only | mandatory | Blade expansion card (daughter card) 1 MAC address 8. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.18 | ColumnbladeDaughterCard2MACAddress1Vpd | read-only | mandatory | Blade expansion card (daughter card) 2 MAC address 1. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.19 | ColumnbladeDaughterCard2MACAddress2Vpd | read-only | mandatory | Blade expansion card (daughter card) 2 MAC address 2. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.20 | ColumnbladeDaughterCard2MACAddress3Vpd | read-only | mandatory | Blade expansion card (daughter card) 2 MAC address 3. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.21 | ColumnbladeDaughterCard2MACAddress4Vpd | read-only | mandatory | Blade expansion card (daughter card) 2 MAC address 4. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.22 | ColumnbladeDaughterCard2MACAddress5Vpd | read-only | mandatory | Blade expansion card (daughter card) 2 MAC address 5. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.23 | ColumnbladeDaughterCard2MACAddress6Vpd | read-only | mandatory | Blade expansion card (daughter card) 2 MAC address 6. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.24 | ColumnbladeDaughterCard2MACAddress7Vpd | read-only | mandatory | Blade expansion card (daughter card) 2 MAC address 7. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.25 | ColumnbladeDaughterCard2MACAddress8Vpd | read-only | mandatory | Blade expansion card (daughter card) 2 MAC address 8. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.26 | ColumnbladeDaughterCard3MACAddress1Vpd | read-only | mandatory | Blade expansion card (daughter card) 3 MAC address 1. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.27 | ColumnbladeDaughterCard3MACAddress2Vpd | read-only | mandatory | Blade expansion card (daughter card) 3 MAC address 2. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.28 | ColumnbladeDaughterCard3MACAddress3Vpd | read-only | mandatory | Blade expansion card (daughter card) 3 MAC address 3. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.29 | ColumnbladeDaughterCard3MACAddress4Vpd | read-only | mandatory | Blade expansion card (daughter card) 3 MAC address 4. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.30 | ColumnbladeDaughterCard3MACAddress5Vpd | read-only | mandatory | Blade expansion card (daughter card) 3 MAC address 5. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.31 | ColumnbladeDaughterCard3MACAddress6Vpd | read-only | mandatory | Blade expansion card (daughter card) 3 MAC address 6. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.32 | ColumnbladeDaughterCard3MACAddress7Vpd | read-only | mandatory | Blade expansion card (daughter card) 3 MAC address 7. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.33 | ColumnbladeDaughterCard3MACAddress8Vpd | read-only | mandatory | Blade expansion card (daughter card) 3 MAC address 8. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.34 | ColumnbladeDaughterCard4MACAddress1Vpd | read-only | mandatory | Blade expansion card (daughter card) 4 MAC address 1. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.35 | ColumnbladeDaughterCard4MACAddress2Vpd | read-only | mandatory | Blade expansion card (daughter card) 4 MAC address 2. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.36 | ColumnbladeDaughterCard4MACAddress3Vpd | read-only | mandatory | Blade expansion card (daughter card) 4 MAC address 3. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.37 | ColumnbladeDaughterCard4MACAddress4Vpd | read-only | mandatory | Blade expansion card (daughter card) 4 MAC address 4. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.38 | ColumnbladeDaughterCard4MACAddress5Vpd | read-only | mandatory | Blade expansion card (daughter card) 4 MAC address 5. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.39 | ColumnbladeDaughterCard4MACAddress6Vpd | read-only | mandatory | Blade expansion card (daughter card) 4 MAC address 6. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.40 | ColumnbladeDaughterCard4MACAddress7Vpd | read-only | mandatory | Blade expansion card (daughter card) 4 MAC address 7. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.41 | ColumnbladeDaughterCard4MACAddress8Vpd | read-only | mandatory | Blade expansion card (daughter card) 4 MAC address 8. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.42 | ColumnbladeDaughterCard5MACAddress1Vpd | read-only | mandatory | Blade expansion card (daughter card) 5 MAC address 1. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.43 | ColumnbladeDaughterCard5MACAddress2Vpd | read-only | mandatory | Blade expansion card (daughter card) 5 MAC address 2. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.44 | ColumnbladeDaughterCard5MACAddress3Vpd | read-only | mandatory | Blade expansion card (daughter card) 5 MAC address 3. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.45 | ColumnbladeDaughterCard5MACAddress4Vpd | read-only | mandatory | Blade expansion card (daughter card) 5 MAC address 4. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.46 | ColumnbladeDaughterCard5MACAddress5Vpd | read-only | mandatory | Blade expansion card (daughter card) 5 MAC address 5. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.47 | ColumnbladeDaughterCard5MACAddress6Vpd | read-only | mandatory | Blade expansion card (daughter card) 5 MAC address 6. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.48 | ColumnbladeDaughterCard5MACAddress7Vpd | read-only | mandatory | Blade expansion card (daughter card) 5 MAC address 7. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.49 | ColumnbladeDaughterCard5MACAddress8Vpd | read-only | mandatory | Blade expansion card (daughter card) 5 MAC address 8. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.100 | ColumnbladeHSDaughterCard1MACAddress1Vpd | read-only | mandatory | Blade high speed expansion card (daughter card) 1 MAC address 1. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.101 | ColumnbladeHSDaughterCard1MACAddress2Vpd | read-only | mandatory | Blade high speed expansion card (daughter card) 1 MAC address 2. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.102 | ColumnbladeHSDaughterCard1MACAddress3Vpd | read-only | mandatory | Blade high speed expansion card (daughter card) 1 MAC address 3. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.103 | ColumnbladeHSDaughterCard1MACAddress4Vpd | read-only | mandatory | Blade high speed expansion card (daughter card) 1 MAC address 4. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.104 | ColumnbladeHSDaughterCard1MACAddress5Vpd | read-only | mandatory | Blade high speed expansion card (daughter card) 1 MAC address 5. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.105 | ColumnbladeHSDaughterCard1MACAddress6Vpd | read-only | mandatory | Blade high speed expansion card (daughter card) 1 MAC address 6. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.106 | ColumnbladeHSDaughterCard1MACAddress7Vpd | read-only | mandatory | Blade high speed expansion card (daughter card) 1 MAC address 7. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.107 | ColumnbladeHSDaughterCard1MACAddress8Vpd | read-only | mandatory | Blade high speed expansion card (daughter card) 1 MAC address 8. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.164 | ColumnbladeSideCardMACAddress1Vpd | read-only | mandatory | Blade side card MAC address 1. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.165 | ColumnbladeSideCardMACAddress2Vpd | read-only | mandatory | Blade side card MAC address 2. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.166 | ColumnbladeSideCardMACAddress3Vpd | read-only | mandatory | Blade side card MAC address 3. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.167 | ColumnbladeSideCardMACAddress4Vpd | read-only | mandatory | Blade side card MAC address 4. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.168 | ColumnbladeSideCardMACAddress5Vpd | read-only | mandatory | Blade side card MAC address 5. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.169 | ColumnbladeSideCardMACAddress6Vpd | read-only | mandatory | Blade side card MAC address 6. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.170 | ColumnbladeSideCardMACAddress7Vpd | read-only | mandatory | Blade side card MAC address 7. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.171 | ColumnbladeSideCardMACAddress8Vpd | read-only | mandatory | Blade side card MAC address 8. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5 | TablebladeExpCardVpdTable | not-accessible | deprecated | Table of VPD information for the blade expansion card components. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1 | RowbladeExpCardVpdEntry | not-accessible | deprecated | Blade expansion card VPD entry. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.1 | ColumnbladeExpCardVpdIndex | read-only | deprecated | Blade expansion card VPD index. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.2 | ColumnbladeExpCardVpdBayNumber | read-only | deprecated | Blade expansion card VPD Bay number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.3 | ColumnbladeExpCardVpdManufacturingId | read-only | deprecated | Blade expansion card VPD manufacturing ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.4 | ColumnbladeExpCardVpdFruNumber | read-only | deprecated | Blade expansion card VPD FRU number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.5 | ColumnbladeExpCardVpdHardwareRevision | read-only | deprecated | Blade expansion card VPD hardware revision. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the … |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.6 | ColumnbladeExpCardVpdSerialNumber | read-only | deprecated | Blade expansion card VPD serial number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.7 | ColumnbladeExpCardVpdMachineType | read-only | deprecated | Blade expansion card VPD machine type. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.8 | ColumnbladeExpCardVpdUuid | read-only | deprecated | Blade expansion card VPD UUID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.9 | ColumnbladeExpCardVpdManufDate | read-only | deprecated | Blade expansion card VPD Manufacture Date. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.10 | ColumnbladeExpCardVpdPartNumber | read-only | deprecated | Blade expansion card VPD Part number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.11 | ColumnbladeExpCardVpdFruSerial | read-only | deprecated | Blade expansion card VPD FRU serial number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.12 | ColumnbladeExpCardVpdMachineModel | read-only | deprecated | Blade expansion card VPD machine model. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.13 | ColumnbladeExpCardVpdManufacturingIDNumber | read-only | deprecated | Blade expansion card VPD Manufacturer ID Number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.14 | ColumnbladeExpCardVpdProductId | read-only | deprecated | Blade expansion card VPD Product ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.15 | ColumnbladeExpCardVpdSubManufacturerId | read-only | deprecated | Blade expansion card VPD subsystem manufacturer ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.16 | ColumnbladeExpCardVpdClei | read-only | deprecated | Blade expansion card VPD Common Language Equipment Identifier (CLEI). For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.19 | ColumnbladeExpCardVpdBladeBayNumber | read-only | deprecated | Blade bay number of the blade expansion card. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.21 | ColumnbladeExpCardVpdCardTypeInfo | read-only | deprecated | Blade expansion card (daughter card) VPD type code that describes the expansion card. For consistent results, view as a table and not as individual entries. NO… |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.22 | ColumnbladeExpCardVpdHighSpeed | read-only | deprecated | Blade expansion card (daughter card) VPD high speed that indicates whether the expansion card is high speed or not. For consistent results, view as a table and… |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.23 | ColumnbladeExpCardVpdHardwareRevisionString | read-only | deprecated | Blade expansion card VPD hardware revision in string format. For consistent results, view as a table and not as individual entries. If a hardware revision is p… |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.7 | TablebladeAndExpCardWwnGuidVpdTable | not-accessible | deprecated | Table of World Wide Names (WWN), Global Unique IDs (GUID) and Serial Attach SCSI IDs (SAS) of the blade server and its expansion cards (daughter cards). For co… |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1 | RowbladeAndExpCardWwnGuidVpdEntry | not-accessible | deprecated | Blade WWN/GUID entries. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.1 | ColumnbladeAndExpCardWwnGuidVpdIndex | read-only | deprecated | Blade or expansion card index. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.2 | ColumnbladeAndExpCardWwnGuidVpdBayNumber | read-only | deprecated | Blade or expansion card VPD bay number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.3 | ColumnbladeAndExpCardWwnGuidVpdName | read-only | deprecated | The name of the blade or expansion card. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.4 | ColumnbladeAndExpCardWwnGuidVpdBladeBayNumber | read-only | deprecated | For expansion cards, it's the blade bay number of the blade expansion card. For blades, it's the bay number of the blade. For consistent results, view as a tab… |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.5 | ColumnbladeAndExpCardWwnGuidVpdType | read-only | deprecated | Blade or expansion card WWN/GUID/SAS Type. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.6 | ColumnbladeAndExpCardWwnGuidVpd1 | read-only | deprecated | Blade or expansion card WWN/GUID 1. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.7 | ColumnbladeAndExpCardWwnGuidVpd2 | read-only | deprecated | Blade or expansion card WWN/GUID 2. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.8 | ColumnbladeAndExpCardWwnGuidVpd3 | read-only | deprecated | Blade or expansion card WWN/GUID 3. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.9 | ColumnbladeAndExpCardWwnGuidVpd4 | read-only | deprecated | Blade or expansion card WWN/GUID 4. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.10 | ColumnbladeAndExpCardWwnGuidVpd5 | read-only | deprecated | Blade or expansion card WWN/GUID 5. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.11 | ColumnbladeAndExpCardWwnGuidVpd6 | read-only | deprecated | Blade or expansion card WWN/GUID 6. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.12 | ColumnbladeAndExpCardWwnGuidVpd7 | read-only | deprecated | Blade or expansion card WWN/GUID 7. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.13 | ColumnbladeAndExpCardWwnGuidVpd8 | read-only | deprecated | Blade or expansion card WWN/GUID 8. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.8 | TablebladeManagementCardVpdTable | not-accessible | deprecated | Table of VPD information for the blade management card component. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1 | RowbladeManagementCardVpdEntry | not-accessible | deprecated | Blade management card VPD entry. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.1 | ColumnbladeManagementCardVpdIndex | read-only | deprecated | Blade management card VPD index. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.2 | ColumnbladeManagementCardVpdBayNumber | read-only | deprecated | Blade management card VPD Bay number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.3 | ColumnbladeManagementCardVpdManufacturingId | read-only | deprecated | Blade management card VPD manufacturing ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.4 | ColumnbladeManagementCardVpdFruNumber | read-only | deprecated | Blade management card VPD FRU number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.5 | ColumnbladeManagementCardVpdHardwareRevision | read-only | deprecated | Blade management card VPD hardware revision. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the… |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.6 | ColumnbladeManagementCardVpdSerialNumber | read-only | deprecated | Blade management card VPD serial number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.7 | ColumnbladeManagementCardVpdMachineType | read-only | deprecated | Blade management card VPD machine type. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.8 | ColumnbladeManagementCardVpdUuid | read-only | deprecated | Blade management card VPD UUID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.9 | ColumnbladeManagementCardVpdManufDate | read-only | deprecated | Blade management card VPD Manufacture Date. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.10 | ColumnbladeManagementCardVpdPartNumber | read-only | deprecated | Blade management card VPD Part number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.11 | ColumnbladeManagementCardVpdFruSerial | read-only | deprecated | Blade management card VPD FRU serial number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.12 | ColumnbladeManagementCardVpdMachineModel | read-only | deprecated | Blade management card VPD machine model. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.13 | ColumnbladeManagementCardVpdManufacturingIDNumber | read-only | deprecated | Blade management card VPD manufacturer ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.14 | ColumnbladeManagementCardVpdProductId | read-only | deprecated | Blade management card VPD Product ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.15 | ColumnbladeManagementCardVpdSubManufacturerId | read-only | deprecated | Blade management card VPD subsystem manufacturer ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.16 | ColumnbladeManagementCardVpdClei | read-only | deprecated | Blade management card VPD Common Language Equipment Identifier (CLEI). For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.17 | ColumnbladeManagementCardVpdHardwareRevisionString | read-only | deprecated | Blade management card VPD hardware revision in string format. For consistent results, view as a table and not as individual entries. If a hardware revision is … |
| 1.3.6.1.4.1.2.3.51.2.2.21.5 | NodebladeFirmwareVpd | |||
| 1.3.6.1.4.1.2.3.51.2.2.21.5.1 | TablebladeBiosVPDTable | not-accessible | deprecated | Table of blade firmware vital product data (VPD) information. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1 | RowbladeBiosVPDEntry | not-accessible | deprecated | Blade firmware VPD table entry |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1.1 | ColumnbladeBiosVpdIndex | read-only | deprecated | Blade firmware VPD table index. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1.2 | ColumnbladeBiosVpdId | read-only | deprecated | The numeric blade ID. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1.3 | ColumnbladeBiosVpdExists | read-only | deprecated | Indicates whether the server blade specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1.4 | ColumnbladeBiosVpdPowerState | read-only | deprecated | Indicates the power state of the blade specified. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1.5 | ColumnbladeBiosVpdName | read-only | deprecated | The name of the blade as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1.6 | ColumnbladeBiosVpdBuildId | read-only | deprecated | The build ID for the blade firmware. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1.7 | ColumnbladeBiosVpdRevision | read-only | deprecated | The revision of the blade firmware. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1.8 | ColumnbladeBiosVpdDate | read-only | deprecated | The date of the blade firmware. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1.9 | ColumnbladeBiosVpdLevelStatus | read-only | deprecated | The level status of the blade bios firmware build ID. It has three possible values as Different (mismatch firmware build ID), Match (the same firmware build ID… |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.2 | TablebladeDiagsVPDTable | not-accessible | deprecated | Table of blade firmware vital product data (VPD) information. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1 | RowbladeDiagsVPDEntry | not-accessible | deprecated | Blade firmware VPD table entry |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1.1 | ColumnbladeDiagsVpdIndex | read-only | deprecated | Blade firmware VPD table index. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1.2 | ColumnbladeDiagsVpdId | read-only | deprecated | The numeric blade ID. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1.3 | ColumnbladeDiagsVpdExists | read-only | deprecated | Indicates whether the server blade specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1.4 | ColumnbladeDiagsVpdPowerState | read-only | deprecated | Indicates the power state of the blade specified. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1.5 | ColumnbladeDiagsVpdName | read-only | deprecated | The name of the blade as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1.6 | ColumnbladeDiagsVpdBuildId | read-only | deprecated | The build ID for the blade firmware. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1.7 | ColumnbladeDiagsVpdRevision | read-only | deprecated | The revision of the blade firmware. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1.8 | ColumnbladeDiagsVpdDate | read-only | deprecated | The date of the blade firmware. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1.9 | ColumnbladeDiagsVpdLevelStatus | read-only | deprecated | The level status of the blade diagnostics firmware build ID. It has three possible values as Different (mismatch firmware build ID), Match (the same firmware b… |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.3 | TablebladeSysMgmtProcVPDTable | not-accessible | deprecated | Table of blade firmware vital product data (VPD) information. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.3.1 | RowbladeSysMgmtProcVPDEntry | not-accessible | deprecated | Blade firmware VPD table entry |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.3.1.1 | ColumnbladeSysMgmtProcVpdIndex | read-only | deprecated | Blade firmware VPD table index. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.3.1.2 | ColumnbladeSysMgmtProcVpdId | read-only | deprecated | The numeric blade ID. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.3.1.3 | ColumnbladeSysMgmtProcVpdExists | read-only | deprecated | Indicates whether the server blade specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.3.1.4 | ColumnbladeSysMgmtProcVpdPowerState | read-only | deprecated | Indicates the power state of the blade specified. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.3.1.5 | ColumnbladeSysMgmtProcVpdName | read-only | deprecated | The name of the blade as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.3.1.6 | ColumnbladeSysMgmtProcVpdBuildId | read-only | deprecated | The build ID for the blade firmware. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.3.1.7 | ColumnbladeSysMgmtProcVpdRevision | read-only | deprecated | The revision of the blade firmware. |
| 1.3.6.1.4.1.2.3.51.2.2.21.5.3.1.8 | ColumnbladeSysMgmtProcVpdLevelStatus | read-only | deprecated | The level status of the blade system management processor firmware build ID. It has three possible values as Different (mismatch firmware build ID), Match (the… |
| 1.3.6.1.4.1.2.3.51.2.2.21.6 | NodesmHardwareVpd | |||
| 1.3.6.1.4.1.2.3.51.2.2.21.6.1 | TablesmHardwareVpdTable | not-accessible | deprecated | Table of the switch module hardware components. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1 | RowsmHardwareVpdEntry | not-accessible | deprecated | Switch module hardware VPD entry. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.1 | ColumnsmHardwareVpdIndex | read-only | deprecated | Switch module hardware VPD index. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.2 | ColumnsmHardwareVpdBayNumber | read-only | deprecated | Switch module hardware VPD Bay number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.3 | ColumnsmHardwareVpdManufacturingId | read-only | deprecated | Switch module hardware VPD manufacturing ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.4 | ColumnsmHardwareVpdFruNumber | read-only | deprecated | Switch module hardware VPD FRU number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.5 | ColumnsmHardwareVpdHardwareRevision | read-only | deprecated | Switch module hardware VPD hardware revision. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in th… |
| 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.8 | ColumnsmHardwareVpdUuid | read-only | deprecated | Switch module hardware VPD UUID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.9 | ColumnsmHardwareVpdManufDate | read-only | deprecated | Switch module hardware VPD manufacture date. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.10 | ColumnsmHardwareVpdPartNumber | read-only | deprecated | Switch module hardware VPD Part Number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.11 | ColumnsmHardwareVpdFruSerial | read-only | deprecated | Switch module hardware VPD FRU Serial. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.12 | ColumnsmHardwareVpdManufacturingIDNumber | read-only | deprecated | Switch module hardware VPD manufacturer ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.13 | ColumnsmHardwareVpdProductId | read-only | deprecated | Switch module hardware VPD product ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.14 | ColumnsmHardwareVpdSubManufacturerId | read-only | deprecated | Switch module hardware VPD subsystem manufacturer ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.15 | ColumnsmHardwareVpdClei | read-only | deprecated | Switch module hardware VPD Common Language Equipment Identifier (CLEI). For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.16 | ColumnsmHardwareVpdWwnGuid | read-only | deprecated | Switch module hardware VPD World Wide Name or Global Unique ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.17 | ColumnsmHardwareVpdWwnGuidType | read-only | deprecated | The WWN/GUID/SAS entry is actually World Wide Name, Global Unique ID or Serial Attach SCSI ID. For consistent results, view as a table and not as individual en… |
| 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.18 | ColumnsmHardwareVpdWidth | read-only | deprecated | The width of the switch module hardware. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.20 | ColumnsmHardwareVpdHardwareRevisionString | read-only | deprecated | Switch module hardware VPD hardware revision in string format. For consistent results, view as a table and not as individual entries. If a hardware revision is… |
| 1.3.6.1.4.1.2.3.51.2.2.21.7 | NodesmFirmwareVpd | |||
| 1.3.6.1.4.1.2.3.51.2.2.21.7.1 | TablesmMainAppVpdTable | not-accessible | deprecated | Switch module main application VPD information table. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1 | RowsmMainAppVpdEntry | not-accessible | deprecated | Switch module main application VPD table entry |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.1 | ColumnsmMainAppVpdIndex | read-only | deprecated | Switch module main application VPD entry index. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.2 | ColumnsmMainAppVpdId | read-only | deprecated | The switch module numeric identifier. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.3 | ColumnsmMainAppVpdExists | read-only | deprecated | Indicates whether the switch module specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.4 | ColumnsmMainAppVpdSwitchType | read-only | deprecated | Indicates the type of switch module installed. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.5 | ColumnsmMainApp1VpdBuildId | read-only | deprecated | Switch module firmware build id. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.6 | ColumnsmMainApp1VpdBuildDate | read-only | deprecated | Switch module firmware build date. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.7 | ColumnsmMainApp1VpdRevisionNumber | read-only | deprecated | Switch module firmware revision number. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.8 | ColumnsmMainApp2VpdBuildId | read-only | deprecated | Switch module firmware build id. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.9 | ColumnsmMainApp2VpdBuildDate | read-only | deprecated | Switch module firmware build date. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.10 | ColumnsmMainApp2VpdRevisionNumber | read-only | deprecated | Switch module firmware revision number. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.11 | ColumnsmMainApp3VpdBuildId | read-only | deprecated | I/O Module firmware build id. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.12 | ColumnsmMainApp3VpdBuildDate | read-only | deprecated | I/O Module firmware build date. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.13 | ColumnsmMainApp3VpdRevisionNumber | read-only | deprecated | I/O Module firmware revision number. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.20 | ColumnsmMainAppVpdSwitchSubType | read-only | deprecated | Indicates the subtype of switch module installed. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.2 | TablesmBootRomVpdTable | not-accessible | deprecated | Switch module boot ROM VPD information table. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.2.1 | RowsmBootRomVpdEntry | not-accessible | deprecated | Switch module boot ROM VPD table entry |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.2.1.1 | ColumnsmBootRomVpdIndex | read-only | deprecated | Switch module boot ROM VPD entry index. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.2.1.2 | ColumnsmBootRomVpdId | read-only | deprecated | The switch module numeric identifier. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.2.1.3 | ColumnsmBootRomVpdExists | read-only | deprecated | Indicates whether the switch module specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.2.1.4 | ColumnsmBootRomVpdSwitchType | read-only | deprecated | Indicates the type of switch module installed. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.2.1.5 | ColumnsmBootRomVpdBuildId | read-only | deprecated | Switch module firmware build ID. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.2.1.6 | ColumnsmBootRomVpdBuildDate | read-only | deprecated | Switch module firmware build date. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.2.1.7 | ColumnsmBootRomVpdRevisionNumber | read-only | deprecated | Switch module firmware revision number. |
| 1.3.6.1.4.1.2.3.51.2.2.21.7.2.1.8 | ColumnsmBootRomVpdSwitchSubType | read-only | deprecated | Indicates the subtype of switch module installed. |
| 1.3.6.1.4.1.2.3.51.2.2.21.8 | NodepmHardwareVpd | |||
| 1.3.6.1.4.1.2.3.51.2.2.21.8.1 | TablepmHardwareVpdTable | not-accessible | deprecated | Table of the power module hardware components. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1 | RowpmHardwareVpdEntry | not-accessible | deprecated | Power module hardware VPD entry. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.1 | ColumnpmHardwareVpdIndex | read-only | deprecated | Power module hardware VPD index. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.2 | ColumnpmHardwareVpdBayNumber | read-only | deprecated | Power module hardware VPD Bay number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.3 | ColumnpmHardwareVpdManufacturingId | read-only | deprecated | Power module hardware VPD manufacturing ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.4 | ColumnpmHardwareVpdFruNumber | read-only | deprecated | Power module hardware VPD FRU number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.5 | ColumnpmHardwareVpdHardwareRevision | read-only | deprecated | Power module hardware VPD hardware revision. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the… |
| 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.8 | ColumnpmHardwareVpdUuid | read-only | deprecated | Power module hardware VPD UUID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.9 | ColumnpmHardwareVpdManufDate | read-only | deprecated | Power module hardware VPD Manufacture Date. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.10 | ColumnpmHardwareVpdPartNumber | read-only | deprecated | Power module hardware VPD Part Number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.11 | ColumnpmHardwareVpdFruSerial | read-only | deprecated | Power module hardware VPD FRU Serial. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.12 | ColumnpmHardwareVpdManufacturingIDNumber | read-only | deprecated | Power module hardware VPD manufacturer ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.13 | ColumnpmHardwareVpdProductId | read-only | deprecated | Power module hardware VPD product ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.14 | ColumnpmHardwareVpdSubManufacturerId | read-only | deprecated | Power module hardware VPD subsystem manufacturer ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.15 | ColumnpmHardwareVpdClei | read-only | deprecated | Power module hardware VPD Common Language Equipment Identifier (CLEI). For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.16 | ColumnpmHardwareVpdHardwareRevisionString | read-only | deprecated | Power module hardware VPD hardware revision in string format. For consistent results, view as a table and not as individual entries. If a hardware revision is … |
| 1.3.6.1.4.1.2.3.51.2.2.21.9 | NoderearLEDCardHardwareVpd | |||
| 1.3.6.1.4.1.2.3.51.2.2.21.9.3 | ScalarrearLEDCardHardwareVpdManufacturingId | read-only | deprecated | Rear LED card hardware VPD manufacturing ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.9.4 | ScalarrearLEDCardHardwareVpdFruNumber | read-only | deprecated | Rear LED card hardware VPD FRU number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.9.5 | ScalarrearLEDCardHardwareVpdHardwareRevision | read-only | deprecated | Rear LED card hardware VPD hardware revision. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in th… |
| 1.3.6.1.4.1.2.3.51.2.2.21.9.8 | ScalarrearLEDCardHardwareVpdUuid | read-only | deprecated | Rear LED card hardware VPD UUID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.9.9 | ScalarrearLEDCardHardwareVpdManufacturingIDNumber | read-only | deprecated | Rear LED card hardware VPD manufacturer ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.9.10 | ScalarrearLEDCardHardwareVpdProductId | read-only | deprecated | Rear LED card hardware VPD product ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.9.11 | ScalarrearLEDCardHardwareVpdSubManufacturerId | read-only | deprecated | Rear LED card hardware VPD subsystem manufacturer ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.9.12 | ScalarrearLEDCardHardwareVpdClei | read-only | deprecated | Rear LED card hardware VPD Common Language Equipment Identifier (CLEI). For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.9.17 | ScalarrearLEDCardHardwareVpdHardwareRevisionString | read-only | deprecated | Rear LED card hardware VPD hardware revision in string format. For consistent results, view as a table and not as individual entries. If a hardware revision is… |
| 1.3.6.1.4.1.2.3.51.2.2.21.9.18 | ScalarrearLEDCardHardwareVpdManufDate | read-only | deprecated | Rear LED card hardware VPD Manufacture Date. |
| 1.3.6.1.4.1.2.3.51.2.2.21.9.19 | ScalarrearLEDCardHardwareVpdPartNumber | read-only | deprecated | Rear LED card hardware VPD Part Number. |
| 1.3.6.1.4.1.2.3.51.2.2.21.9.20 | ScalarrearLEDCardHardwareVpdFruSerial | read-only | deprecated | Rear LED card hardware VPD FRU Serial. |
| 1.3.6.1.4.1.2.3.51.2.2.21.12 | NodechassisFanFirmwareVpd | |||
| 1.3.6.1.4.1.2.3.51.2.2.21.12.1 | TablechassisFanControllerVPDTable | not-accessible | deprecated | Table of chassis fan controller firmware vital product data (VPD) information. |
| 1.3.6.1.4.1.2.3.51.2.2.21.12.1.1 | RowchassisFanControllerVPDEntry | not-accessible | deprecated | Chassis fan controller firmware VPD table entry |
| 1.3.6.1.4.1.2.3.51.2.2.21.12.1.1.1 | ColumnchassisFanControllerVpdIndex | read-only | deprecated | Chassis fan controller firmware VPD table index. |
| 1.3.6.1.4.1.2.3.51.2.2.21.12.1.1.2 | ColumnchassisFanControllerVpdId | read-only | deprecated | The numeric chassis fan ID. |
| 1.3.6.1.4.1.2.3.51.2.2.21.12.1.1.3 | ColumnchassisFanControllerVpdExists | read-only | deprecated | Indicates whether the chassis fan specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.2.21.12.1.1.7 | ColumnchassisFanControllerVpdRevision | read-only | deprecated | The revision of the chassis fan controller firmware. |
| 1.3.6.1.4.1.2.3.51.2.2.21.13 | NodechassisFanHardwareVpd | |||
| 1.3.6.1.4.1.2.3.51.2.2.21.13.1 | TablechassisFanHardwareVpdTable | not-accessible | deprecated | Table of the chassis fan hardware components. |
| 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1 | RowchassisFanHardwareVpdEntry | not-accessible | deprecated | Chassis fan hardware VPD entry. |
| 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.1 | ColumnchassisFanHardwareVpdIndex | read-only | deprecated | Chassis fan hardware VPD index. |
| 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.2 | ColumnchassisFanHardwareVpdBayNumber | read-only | deprecated | Chassis fan hardware VPD Bay number. |
| 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.3 | ColumnchassisFanHardwareVpdManufacturingId | read-only | deprecated | Chassis fan hardware VPD manufacturing ID. |
| 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.4 | ColumnchassisFanHardwareVpdFruNumber | read-only | deprecated | Chassis fan hardware VPD FRU number. |
| 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.5 | ColumnchassisFanHardwareVpdHardwareRevision | read-only | deprecated | Chassis fan hardware VPD hardware revision. |
| 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.8 | ColumnchassisFanHardwareVpdUuid | read-only | deprecated | Chassis fan hardware VPD UUID. |
| 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.9 | ColumnchassisFanHardwareVpdManufDate | read-only | deprecated | Chassis fan hardware VPD manufacture Date. |
| 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.10 | ColumnchassisFanHardwareVpdPartNumber | read-only | deprecated | Chassis fan hardware VPD Part Number. |
| 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.11 | ColumnchassisFanHardwareVpdFruSerial | read-only | deprecated | Chassis fan hardware VPD FRU serial number. |
| 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.12 | ColumnchassisFanHardwareVpdManufacturingIDNumber | read-only | deprecated | Chassis fan hardware VPD manufacturer ID. |
| 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.13 | ColumnchassisFanHardwareVpdProductId | read-only | deprecated | Chassis fan hardware VPD product ID. |
| 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.14 | ColumnchassisFanHardwareVpdSubManufacturerId | read-only | deprecated | Chassis fan hardware VPD subsystem manufacturer ID. |
| 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.15 | ColumnchassisFanHardwareVpdClei | read-only | deprecated | Chassis fan hardware VPD Common Language Equipment Identifier (CLEI). |
| 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.16 | ColumnchassisFanHardwareVpdHardwareRevisionString | read-only | deprecated | Chassis fan hardware VPD hardware revision in string format. |
| 1.3.6.1.4.1.2.3.51.2.2.21.14 | NodepmFirmwareVpd | |||
| 1.3.6.1.4.1.2.3.51.2.2.21.14.1 | TablepmControllerVPDTable | not-accessible | deprecated | Table of Power Module controller firmware vital product data (VPD) information. |
| 1.3.6.1.4.1.2.3.51.2.2.21.14.1.1 | RowpmControllerVPDEntry | not-accessible | deprecated | Power Module controller firmware VPD table entry |
| 1.3.6.1.4.1.2.3.51.2.2.21.14.1.1.1 | ColumnpmControllerVpdIndex | read-only | deprecated | Power Module controller firmware VPD table index. |
| 1.3.6.1.4.1.2.3.51.2.2.21.14.1.1.2 | ColumnpmControllerVpdId | read-only | deprecated | The numeric Power Module ID. |
| 1.3.6.1.4.1.2.3.51.2.2.21.14.1.1.3 | ColumnpmControllerVpdExists | read-only | deprecated | Indicates whether the Power Module specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.2.21.14.1.1.7 | ColumnpmControllerVpdRevision | read-only | deprecated | The revision of the Power Module controller firmware. |
| 1.3.6.1.4.1.2.3.51.2.2.21.22 | TableinventoryManagementActivityVpdTable | not-accessible | mandatory | Table of system component hardware VPD activity log. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.22.1 | RowinventoryManagementActivityVpdEntry | not-accessible | mandatory | System component hardware VPD activity log entry. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.22.1.1 | ColumncomponentLevelActivityVpdIndex | read-only | mandatory | System component level VPD activity log index. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.22.1.2 | ColumncomponentLevelActivityVpdFruNumber | read-only | mandatory | System component level VPD activity log FRU number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.22.1.3 | ColumncomponentLevelActivityVpdSerialNumber | read-only | mandatory | System component level VPD activity log serial number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.22.1.4 | ColumncomponentLevelActivityVpdManufacturingId | read-only | mandatory | System component level VPD activity log manufacturing ID. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.22.1.5 | ColumncomponentLevelActivityVpdBayNumber | read-only | deprecated | System component level VPD activity log Bay number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.22.1.9 | ColumncomponentLevelActivityVpdAction | read-only | mandatory | System component level VPD activity log action (added/removed). For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.22.1.10 | ColumncomponentLevelActivityVpdTimestamp | read-only | mandatory | System component level VPD activity log timestamp. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.22.1.12 | ColumncomponentLevelActivityVpdModuleName | read-only | mandatory | The module name which this row is associated with. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.2.21.22.1.15 | ColumncomponentLevelActivityVpdTopologyPath | read-only | mandatory | The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. As an example, the roo… |
| 1.3.6.1.4.1.2.3.51.2.2.21.23 | NodereloadVpdData | |||
| 1.3.6.1.4.1.2.3.51.2.2.21.23.1 | ScalarreloadAllVpdData | read-write | mandatory | Reload all VPD data (firmware, hardware, MAC address, WWN/GUID and other Unique ID). NOTE: The value returned for the GET command is meaningless. |
| 1.3.6.1.4.1.2.3.51.2.2.21.23.2 | ScalarreloadFwVpdData | read-write | mandatory | Reload firmware VPD data. NOTE: The value returned for the GET command is meaningless. |
| 1.3.6.1.4.1.2.3.51.2.2.21.23.3 | ScalarreloadHwVpdData | read-write | mandatory | Reload hardware VPD data. NOTE: The value returned for the GET command is meaningless. |
| 1.3.6.1.4.1.2.3.51.2.2.21.23.4 | ScalarreloadMACAddress | read-write | mandatory | Reload blade MAC addresses. NOTE: The value returned for the GET command is meaningless. |
| 1.3.6.1.4.1.2.3.51.2.2.21.23.5 | ScalarreloadWwnGuidVpdData | read-write | mandatory | Reload blade and I/O module WWN/GUID and other VPD data. NOTE: The value returned for the GET command is meaningless. |
| 1.3.6.1.4.1.2.3.51.2.2.22 | NodeairFilter | |||
| 1.3.6.1.4.1.2.3.51.2.2.22.1 | NodepassiveAirFilter | |||
| 1.3.6.1.4.1.2.3.51.2.2.22.1.1 | ScalarpassiveAirFilterStatus | read-write | mandatory | Disable/Enable/Reset the passive air filter. When enabled, sending an enable or reset will reset the replace date. |
| 1.3.6.1.4.1.2.3.51.2.2.22.1.2 | ScalarpassiveAirFilterMonthFreq | read-write | mandatory | The chassis environment. 1 month indicates high dust, 3 months indicates moderate dust and, 6 months indicates low dust. |
| 1.3.6.1.4.1.2.3.51.2.2.22.1.3 | ScalarpassiveAirFilterReplaceDate | read-only | mandatory | The scheduled replacement date of the air filter. |
| 1.3.6.1.4.1.2.3.51.2.2.23 | NodecomponentInformation | |||
| 1.3.6.1.4.1.2.3.51.2.2.23.1 | NodecomponentInventory | |||
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1 | TablecomponentInventoryTable | not-accessible | mandatory | Table of component inventory information. Not all components will provide every object defined in the ComponentInventoryEntry. Also, if a component does not ha… |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1 | RowcomponentInventoryEntry | not-accessible | mandatory | Component inventory information. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.1 | ColumncomponentInventoryTopologyPath | read-only | mandatory | The unique identifier for a row in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree… |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.2 | ColumncomponentInventoryInstance | read-only | mandatory | The slot number or instance of a particular component. Typically, if the component plugs into the chassis, this represents the slot number. However, some compo… |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.3 | ColumncomponentInventoryDescription | read-only | mandatory | A short text string describing the particular component. If a text string is not available, a value of 'Not available' is presented. For more detail, also refe… |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.4 | ColumncomponentInventoryMachineTypeModel | read-only | mandatory | The machine type and model number of this component. Typically, the format is XXXXYYY, where XXXX reprsents the machine type and YYY represents the model numbe… |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.5 | ColumncomponentInventoryMachineSerial | read-only | mandatory | The machine serial number of this component. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.6 | ColumncomponentInventoryAssetID | read-only | mandatory | The asset identifier of this component, typically set by some other authority than the manufacturer. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.7 | ColumncomponentInventoryPartNumber | read-only | mandatory | The part number of this component. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.8 | ColumncomponentInventoryFRUNumber | read-only | mandatory | The Field Replaceable Unit (FRU) number of this component. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.9 | ColumncomponentInventoryFRUSerialNumber | read-only | mandatory | The Field Replaceable Unit (FRU) serial number of this component. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.10 | ColumncomponentInventoryManufacture | read-only | mandatory | The text description of the manufacturer of this component. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.11 | ColumncomponentInventoryHardwareRevision | read-only | mandatory | The hardware revision number of the this component. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.12 | ColumncomponentInventoryManufactureDate | read-only | mandatory | The date when the manufacturer created this component. The format is XXYY, where XX is the week number of the year 20YY. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.13 | ColumncomponentInventoryUUID | read-only | mandatory | The Universally Unique IDentifier (UUID) of this component, represented as a 16 byte hex number. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.14 | ColumncomponentInventoryProductID | read-only | mandatory | The product identifier of the component assigned by the manufacturer. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.15 | ColumncomponentInventorySubManufactureID | read-only | mandatory | The text sub-description of the manufacturer of this component, often used to identify a supplier for a component which has multiple suppliers. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.16 | ColumncomponentInventoryCLEI | read-only | mandatory | The Common Language Equipment Identifier (CLEI) of this component. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.17 | ColumncomponentInventoryAssetTag | read-only | mandatory | The asset tag of this component. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.18 | ColumncomponentInventorySpeed | read-only | mandatory | A speed designation for the component, for example, processor speed. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.19 | ColumncomponentInventoryIdentifier | read-only | mandatory | A unique identifier assigned by the manufacturer to the component, for example, a processor ID. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.20 | ColumncomponentInventorySize | read-only | mandatory | A size designation for the component, for example, a memory DIMM size or hard drive capacity. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.21 | ColumncomponentInventoryMemoryType | read-only | mandatory | The architecture specification of a memory device. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.22 | ColumncomponentInventoryProductName | read-only | mandatory | The product name assigned by the manufacturer for this component. For more detail, also refer to the componentInventoryDescription object. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.23 | ColumncomponentInventoryProductVersion | read-only | mandatory | The product version assigned by the manufacturer for this component. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.24 | ColumncomponentInventoryProcessorType | read-only | mandatory | The type designation for processor components. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.25 | ColumncomponentInventoryProcessorFamily | read-only | mandatory | The family designation for processor components. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.26 | ColumncomponentInventoryProcessorCores | read-only | mandatory | The number of cores present on a processor component. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.27 | ColumncomponentInventoryProcessorThreads | read-only | mandatory | The number of threads present on a processor component. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.28 | ColumncomponentInventoryProcessorL1DCache | read-only | mandatory | The level 1 data cache size of a processor component. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.29 | ColumncomponentInventoryProcessorL1ICache | read-only | mandatory | The level 1 instruction cache size of a processor component. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.30 | ColumncomponentInventoryProcessorL2Cache | read-only | mandatory | The level 2 cache size of a processor component. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.31 | ColumncomponentInventoryProcessorL3Cache | read-only | mandatory | The level 3 cache size of a processor component. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.32 | ColumncomponentInventoryProcessorVoltage | read-only | mandatory | The voltage rating for a processor component. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.33 | ColumncomponentInventoryProcessorExtClock | read-only | mandatory | The external clock speed of a processor component. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.34 | ColumncomponentInventoryProcessorDataWidth | read-only | mandatory | The maximum data bus width capability of a processor component, expressed typically in bits. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.35 | ColumncomponentInventoryManufactureIDNum | read-only | mandatory | The identification number assigned for the component by the manufacturer. |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.41 | ColumncomponentInventoryGlobalID | read-only | mandatory | The global identifier (GLID) of this component. This ID is a unique identifier for the CMM chassis (midplane), set by the manufacturer. This ID and the associa… |
| 1.3.6.1.4.1.2.3.51.2.2.23.1.2 | ScalarcomponentInventoryTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentInventoryTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2 | NodecomponentFirmware | |||
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1 | TablecomponentFirmwareTable | not-accessible | mandatory | Table of component firmware information. Not all components will provide every object defined in the ComponentFirmwareEntry. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1 | RowcomponentFirmwareEntry | not-accessible | mandatory | Component firmware information. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.1 | ColumncomponentFirmwareTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.2 | ColumncomponentFirmwareIndex | read-only | mandatory | Each component may have one or more types of firmware associated with it, and this index object identifies the particular instance. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.3 | ColumncomponentFirmwareComponentInstance | read-only | mandatory | The slot number or instance of a particular component. Typically, if the component plugs into the chassis, this represents the slot number. However, some compo… |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.4 | ColumncomponentFirmwareComponentDescription | read-only | mandatory | A short text string describing the particular component. For the MM and blades, this name will be the configured name or its serial number if no user configure… |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.5 | ColumncomponentFirmwareType | read-only | mandatory | A text description of the type of firmware load. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.6 | ColumncomponentFirmwareBuildID | read-only | mandatory | A text description of the build identifier for this firmware load. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.7 | ColumncomponentFirmwareReleaseDate | read-only | mandatory | A text description of the release date for this firmware load. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.8 | ColumncomponentFirmwareFilename | read-only | mandatory | A text description of the filename of this firmware load. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.9 | ColumncomponentFirmwareRevision | read-only | mandatory | A text description of the revision level of this firmware load. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.10 | ColumncomponentFirmwareRevisionMajor | read-only | mandatory | A numeric identifier of the revision major number for this firmware load. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.11 | ColumncomponentFirmwareRevisionMinor | read-only | mandatory | A numeric identifier of the revision minor number for this firmware load. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.12 | ColumncomponentFirmwareLevelStatus | read-only | mandatory | The level status of the firmware build ID. It has three possible values as Different (mismatch firmware build ID), Match (the same firmware build ID), Unique (… |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.13 | ColumncomponentFirmwarePendingBuildID | read-only | mandatory | A text description of the build identifier for this pending firmware load. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.14 | ColumncomponentFirmwarePendingReleaseDate | read-only | mandatory | A text description of the release date for this pending firmware load. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.15 | ColumncomponentFirmwarePendingRevision | read-only | mandatory | A text description of the revision level of this pending firmware load. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.16 | ColumncomponentFirmwareReleaseLevel | read-only | mandatory | A text description of the firmware release level this firmware load. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.17 | ColumncomponentFirmwareImageStatus | read-only | mandatory | This object indicates whether this firmware image is the active (1) firmware,otherwise this firmware image is inactive (0). |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.18 | ColumncomponentFirmwareRole | read-only | mandatory | A text description with the firmware image information. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.20 | ColumncomponentFirmwareTypeID | read-only | mandatory | Indicates the type of firmware load with a numeric identifier. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.2 | ScalarcomponentFirmwareTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentFirmwareTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.7 | TablenodeFirmwareAnalysisTable | not-accessible | mandatory | Table of firmware levels of installed nodes. This information is grouped by Machine Type/Model and includes two or more nodes with the same Type/Model. This in… |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.7.1 | RownodeFirmwareAnalysisEntry | not-accessible | mandatory | Node firmware analysis information. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.7.1.1 | ColumnnodeFirmwareAnalysisIndex | read-only | mandatory | The index for the node firmware levels. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.7.1.2 | ColumnnodeFirmwareAnalysisMachineTypeModel | read-only | mandatory | The machine type or model of node firmware. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.7.1.3 | ColumnnodeFirmwareAnalysisFirmwareType | read-only | mandatory | The firmware type. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.7.1.4 | ColumnnodeFirmwareAnalysisBuildId | read-only | mandatory | The firmware build id. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.7.1.5 | ColumnnodeFirmwareAnalysisReleaseDate | read-only | mandatory | The firmware release date. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.7.1.6 | ColumnnodeFirmwareAnalysisRevisionLevel | read-only | mandatory | The firmware revision level. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.7.1.7 | ColumnnodeFirmwareAnalysisTopology | read-only | mandatory | The node topology. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.7.1.8 | ColumnnodeFirmwareAnalysisDeviceName | read-only | mandatory | The node device name. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.11 | TablesmFirmwareAnalysisTable | not-accessible | mandatory | Table of firmware levels of installed IOMs. This information is grouped by Product Id and includes two or more IOMs with the same product id. This information … |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.11.1 | RowsmFirmwareAnalysisEntry | not-accessible | mandatory | IOM firmware analysis information. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.11.1.1 | ColumnsmFirmwareAnalysisIndex | read-only | mandatory | The index for the IOM firmware levels. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.11.1.2 | ColumnsmFirmwareAnalysisProductId | read-only | mandatory | The IOM product id. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.11.1.3 | ColumnsmFirmwareAnalysisProductName | read-only | mandatory | The IOM product name. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.11.1.4 | ColumnsmFirmwareAnalysisFirmwareType | read-only | mandatory | The IOM firmware type. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.11.1.5 | ColumnsmFirmwareAnalysisFirmwareVersion | read-only | mandatory | The IOM firmware version. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.11.1.6 | ColumnsmFirmwareAnalysisReleaseDate | read-only | mandatory | The IOM release date. |
| 1.3.6.1.4.1.2.3.51.2.2.23.2.11.1.7 | ColumnsmFirmwareAnalysisTopology | read-only | mandatory | The IOM topology. |
| 1.3.6.1.4.1.2.3.51.2.2.23.3 | ScalarcomponentInventoryReady | read-only | mandatory | When a blade management controller, switch or the MM is reset, the inventory data is refreshed in the MM database. This includes items like IBM VPD (e.g. - ser… |
| 1.3.6.1.4.1.2.3.51.2.2.23.10 | TablecomponentDriveTable | not-accessible | mandatory | Table of information indicating presence of a disk drive on a component. The management module does not receive any inventory VPD from the component, so only t… |
| 1.3.6.1.4.1.2.3.51.2.2.23.10.1 | RowcomponentDriveEntry | not-accessible | mandatory | Component drive information. |
| 1.3.6.1.4.1.2.3.51.2.2.23.10.1.1 | ColumncomponentDriveTopologyPath | read-only | mandatory | The unique identifier for a row in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree… |
| 1.3.6.1.4.1.2.3.51.2.2.23.10.1.2 | ColumncomponentDriveDescription | read-only | mandatory | A short text string describing the particular drive on the component. |
| 1.3.6.1.4.1.2.3.51.2.2.23.11 | ScalarcomponentDriveTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentDriveTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.2.30 | NodelicenseKeyInfo | |||
| 1.3.6.1.4.1.2.3.51.2.2.30.1 | TablelicenseKeyInfoTable | not-accessible | mandatory | Table of license key information. |
| 1.3.6.1.4.1.2.3.51.2.2.30.1.1 | RowlicenseKeyInfoEntry | not-accessible | mandatory | License key information entry. |
| 1.3.6.1.4.1.2.3.51.2.2.30.1.1.1 | ColumnlicenseKeyComponentIndex | read-only | mandatory | License key component table index. |
| 1.3.6.1.4.1.2.3.51.2.2.30.1.1.2 | ColumnlicenseKeyIndex | read-only | mandatory | The license key index for the chassis component. |
| 1.3.6.1.4.1.2.3.51.2.2.30.1.1.3 | ColumnlicenseKeyDescription | read-only | mandatory | The description for a license key. |
| 1.3.6.1.4.1.2.3.51.2.2.30.1.1.4 | ColumnlicenseKeyTimestamp | read-only | mandatory | The date and time of this license key. |
| 1.3.6.1.4.1.2.3.51.2.2.30.1.1.5 | ColumnlicenseKeyLicenseID | read-only | mandatory | The unique identifier for this license key. |
| 1.3.6.1.4.1.2.3.51.2.2.30.1.1.6 | ColumnlicenseKeyOtherInfo | read-only | mandatory | Any other information related to this license key. |
| 1.3.6.1.4.1.2.3.51.2.2.30.1.1.7 | ColumnlicenseKeyStatus | read-only | mandatory | The current status of this license key. |
| 1.3.6.1.4.1.2.3.51.2.2.30.5 | TablechassisLicenseKeyTable | not-accessible | mandatory | Table of chassis license key information. |
| 1.3.6.1.4.1.2.3.51.2.2.30.5.1 | RowchassisLicenseKeyEntry | not-accessible | mandatory | Chassis License key information entry. |
| 1.3.6.1.4.1.2.3.51.2.2.30.5.1.1 | ColumnchassisLicenseKeyIndex | read-only | mandatory | The key index for the chassis license keys. |
| 1.3.6.1.4.1.2.3.51.2.2.30.5.1.2 | ColumnchassisLicenseKeyFeature | read-only | mandatory | The name of the Feature for the license key. |
| 1.3.6.1.4.1.2.3.51.2.2.30.5.1.3 | ColumnchassisLicenseKeyFeatureType | read-only | mandatory | The Feature Type Code for the license key. |
| 1.3.6.1.4.1.2.3.51.2.2.30.5.1.4 | ColumnchassisLicenseKeyDescription | read-only | mandatory | The description of the license key. |
| 1.3.6.1.4.1.2.3.51.2.2.30.5.1.5 | ColumnchassisLicenseKeySystem | read-only | mandatory | System information for the license key. |
| 1.3.6.1.4.1.2.3.51.2.2.30.5.1.6 | ColumnchassisLicenseKeyLicenseID | read-only | mandatory | Identification of the license key. |
| 1.3.6.1.4.1.2.3.51.2.2.30.5.1.7 | ColumnchassisLicenseKeyValidation | read-only | mandatory | Validation of the license key. |
| 1.3.6.1.4.1.2.3.51.2.2.30.5.1.8 | ColumnchassisLicenseKeyStatus | read-only | mandatory | The current status of the license key. |
| 1.3.6.1.4.1.2.3.51.2.2.30.5.1.9 | ColumnchassisLicenseKeyTimeLimit | read-only | mandatory | Date and Time (GMT) when license expires. |
| 1.3.6.1.4.1.2.3.51.2.2.30.5.1.10 | ColumnchassisLicenseKeyUsageLimit | read-only | mandatory | Number of times remaining for license usage. A negative value indicates that there is no Usage Limit for the license. |
| 1.3.6.1.4.1.2.3.51.2.3 | NodeerrorLogs | |||
| 1.3.6.1.4.1.2.3.51.2.3.4 | NodeeventLog | |||
| 1.3.6.1.4.1.2.3.51.2.3.4.2 | TablereadEventLogTable | not-accessible | mandatory | Table of event log entry information. |
| 1.3.6.1.4.1.2.3.51.2.3.4.2.1 | RowreadEventLogEntry | not-accessible | mandatory | Event log table entry |
| 1.3.6.1.4.1.2.3.51.2.3.4.2.1.1 | ColumnreadEventLogIndex | read-only | mandatory | The event log index number. |
| 1.3.6.1.4.1.2.3.51.2.3.4.2.1.2 | ColumnreadEventLogString | read-only | mandatory | A string of data detailing an event. |
| 1.3.6.1.4.1.2.3.51.2.3.4.3 | ScalarclearEventLog | read-write | mandatory | Clear the event log. NOTE: Value returned for the GET command is meaningless for this MIB object. |
| 1.3.6.1.4.1.2.3.51.2.3.4.4 | ScalarmonitorLogStateEvents | read-write | mandatory | If disabled, it means the info LED will not turn on when the log gets full and no alerts will be sent out. If enabled, the LED will turn on when the log gets f… |
| 1.3.6.1.4.1.2.3.51.2.3.4.6 | TablereadEnhancedEventLogTable | not-accessible | mandatory | Table of enhanced event log entry information. |
| 1.3.6.1.4.1.2.3.51.2.3.4.6.1 | RowreadEnhancedEventLogEntry | not-accessible | mandatory | Enhaced Event log table entry, new entries could be added for new items. |
| 1.3.6.1.4.1.2.3.51.2.3.4.6.1.1 | ColumnreadEnhancedEventLogNumber | read-only | mandatory | The event log number for the enhanced event log. |
| 1.3.6.1.4.1.2.3.51.2.3.4.6.1.2 | ColumnreadEnhancedEventLogAttribute | read-only | mandatory | A string of data detailing an event log's attribute, such as the Event ID and Call Home Flag. The Event ID is a hexadecimal number representing an specific or … |
| 1.3.6.1.4.1.2.3.51.2.3.4.6.1.3 | ColumnreadEnhancedEventLogMessage | read-only | mandatory | A string of data detailing an event log message. |
| 1.3.6.1.4.1.2.3.51.2.3.4.6.1.4 | ColumnreadEnhancedEventLogSequenceNum | read-only | mandatory | The sequence number for the enhanced event log. This number is the next sequence number when this event record was create. This number continues to grow, even … |
| 1.3.6.1.4.1.2.3.51.2.3.4.10 | TablereadAuditLogTable | not-accessible | mandatory | Table of audit log entry information. Audit log includes the logs whose source is 'Audit' |
| 1.3.6.1.4.1.2.3.51.2.3.4.10.1 | RowreadAuditLogEntry | not-accessible | mandatory | Audit log table entry, new entries could be added for new items. |
| 1.3.6.1.4.1.2.3.51.2.3.4.10.1.1 | ColumnreadAuditLogNumber | read-only | mandatory | The audit log number. |
| 1.3.6.1.4.1.2.3.51.2.3.4.10.1.2 | ColumnreadAuditLogAttribute | read-only | mandatory | A string of data detailing an audit eventlog's attribute. |
| 1.3.6.1.4.1.2.3.51.2.3.4.10.1.3 | ColumnreadAuditLogMessage | read-only | mandatory | A string of data detailing an audit event log message. |
| 1.3.6.1.4.1.2.3.51.2.3.4.10.1.4 | ColumnreadAuditLogSequenceNum | read-only | mandatory | The sequence number for the audit event log. This number is the next sequence number when this event record was create. This number continues to grow, even if … |
| 1.3.6.1.4.1.2.3.51.2.3.4.11 | ScalarclearAuditLog | read-write | mandatory | Clear the audit log. NOTE: Value returned for the GET command is meaningless for this MIB object. |
| 1.3.6.1.4.1.2.3.51.2.3.4.12 | TablereadSystemLogTable | not-accessible | mandatory | Table of system log entry information. System log includes the logs whose source is other than 'Audit' |
| 1.3.6.1.4.1.2.3.51.2.3.4.12.1 | RowreadSystemLogEntry | not-accessible | mandatory | System log table entry, new entries could be added for new items. |
| 1.3.6.1.4.1.2.3.51.2.3.4.12.1.1 | ColumnreadSystemLogNumber | read-only | mandatory | The system log index number. |
| 1.3.6.1.4.1.2.3.51.2.3.4.12.1.2 | ColumnreadSystemLogAttribute | read-only | mandatory | A string of data detailing an system event log's attribute. |
| 1.3.6.1.4.1.2.3.51.2.3.4.12.1.3 | ColumnreadSystemLogMessage | read-only | mandatory | A string of data detailing an system event log message. |
| 1.3.6.1.4.1.2.3.51.2.3.4.12.1.4 | ColumnreadSystemLogSequenceNum | read-only | mandatory | The sequence number for the system event log. This number is the next sequence number when this event record was create. This number continues to grow, even if… |
| 1.3.6.1.4.1.2.3.51.2.3.4.13 | ScalarclearSystemLog | read-write | mandatory | Clear the system log. NOTE: Value returned for the GET command is meaningless for this MIB object. |
| 1.3.6.1.4.1.2.3.51.2.3.4.14 | TablereadEventLogAuxTable | not-accessible | mandatory | Table of system log entry auxiliary information. |
| 1.3.6.1.4.1.2.3.51.2.3.4.14.1 | RowreadEventLogAuxEntry | not-accessible | mandatory | Event log auxiliary table entry, new entries could be added for new items. |
| 1.3.6.1.4.1.2.3.51.2.3.4.14.1.1 | ColumnreadEventLogAuxNumber | read-only | mandatory | The system log auxiliary index number. To relate this information to the system log, match Sequence number of this entry to the Sequence number of the system l… |
| 1.3.6.1.4.1.2.3.51.2.3.4.14.1.2 | ColumnreadEventLogAuxSequenceNum | read-only | mandatory | The sequence number for the system event log that contains this Auxiliary information. Value is from 1 through 4294967295 and then wraps. |
| 1.3.6.1.4.1.2.3.51.2.3.4.14.1.3 | ColumnreadEventLogAuxMessage | read-only | mandatory | A string of data detailing the auxiliary information from the log event. |
| 1.3.6.1.4.1.2.3.51.2.4 | NodeconfigureSP | |||
| 1.3.6.1.4.1.2.3.51.2.4.1 | NoderemoteAccessConfig | |||
| 1.3.6.1.4.1.2.3.51.2.4.1.1 | NodegeneralRemoteCfg | |||
| 1.3.6.1.4.1.2.3.51.2.4.1.1.3 | ScalarremoteAlertRetryDelay | read-write | mandatory | Number in seconds to delay between retries if sending a remote alert is unsuccessful. |
| 1.3.6.1.4.1.2.3.51.2.4.1.1.4 | ScalarremoteAlertRetryCount | read-write | mandatory | Number of additional times a remote alert will be retried if not successfully sent. A value of zero indicates no retries will be attempted. |
| 1.3.6.1.4.1.2.3.51.2.4.1.1.7 | ScalaruserAuthenticationMethod | read-write | mandatory | Use this field to specify how users attempting to login should be authenticated. There are two methods: Local authentication. Userid and password are verified … |
| 1.3.6.1.4.1.2.3.51.2.4.1.1.9 | ScalarmaxSessionsPerLDAPUser | read-write | mandatory | The maximum number of simultaneous active sessions allowed for each LDAP user. If the value is 0, this option is disabled. The minimum value is 1 and the maxim… |
| 1.3.6.1.4.1.2.3.51.2.4.1.1.10 | ScalarauthenticationLoggingTimeout | read-write | mandatory | Use this option to set how long, in seconds, MM will not log the authentication events for the same user. The default setting is 5 minutes. 0 indicates log all… |
| 1.3.6.1.4.1.2.3.51.2.4.1.1.11 | ScalartrackingIP | read-write | mandatory | This option indicates tracking different IP addresses for the same user is enabled or not. If it is enabled then an access every second from alternating IP add… |
| 1.3.6.1.4.1.2.3.51.2.4.1.1.20 | NodeaccountSecurityManagement | |||
| 1.3.6.1.4.1.2.3.51.2.4.1.1.20.1 | ScalaraccountSecurityLevel | read-write | mandatory | The level of security needed for local user login passwords. The legacy level: - no password required - no password expiration - no password re-use restriction… |
| 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2 | NodecustomSecuritySettings | |||
| 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.2 | ScalarpasswordExpirationPeriod | read-write | mandatory | The number of days before login passwords expire. The minimum value is 1 day and the maximum value is 365 days. The default value is 90 days. A value of 0 disa… |
| 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.3 | ScalardefaultAdminPasswordExpired | read-write | mandatory | If enabled, the factory default 'USERID' account password must be changed on next login. The default value is disabled. |
| 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.4 | ScalarminimumPasswordReuseCycle | read-write | mandatory | The number of unique passwords a user must choose before reusing a password. The default value is none. |
| 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.5 | ScalarcomplexPasswordRules | read-write | mandatory | If enabled, the minimum complexity rules will be enforced for all local login passwords and 'User login password required' rule will be enabled. The complex ru… |
| 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.6 | ScalarminimumDiffCharsPassword | read-write | mandatory | The required minimum number of characters in the new password different from the previous password. The default value is 2. A SET of this object is ignored unt… |
| 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.7 | ScalarchangePasswordFirstAccess | read-write | mandatory | If enabled, the login user will be forced to change their password on the first access after the account has been established or on the first access after an a… |
| 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.8 | ScalarinactivityAlertPeriod | read-write | mandatory | The period of time in days before generating an alert for a dormant account. This value applies to all login accounts, including the administrator account. The… |
| 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.9 | ScalarinactivityAlertDisablePeriod | read-write | mandatory | The period of time in days before generating an alert and disabling a dormant account. This value applies to all login accounts, excluding the administrator ac… |
| 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.10 | ScalarlockoutPeriod | read-write | mandatory | The period of time in minutes that a user is locked out after the maximum number of login failures was reached. The minimum value is is 1 minute and the maximu… |
| 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.11 | ScalarmaxLoginFailures | read-write | mandatory | The maximum number of login failures before a user account is locked. A value of 0 disables this option. The default value is 5. |
| 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.12 | ScalarpasswordChangeInterval | read-write | mandatory | A minimum period of time that user is not able to change their own password. The range of acceptable values will be from 0 to 1440 (or 60 days). A value of 0 d… |
| 1.3.6.1.4.1.2.3.51.2.4.1.2 | NodeserialPortCfg | |||
| 1.3.6.1.4.1.2.3.51.2.4.1.2.1 | ScalarportBaud | read-write | mandatory | Baud rate for the serial port. |
| 1.3.6.1.4.1.2.3.51.2.4.1.2.2 | ScalarportParity | read-write | mandatory | Parity setting for the serial port. |
| 1.3.6.1.4.1.2.3.51.2.4.1.2.3 | ScalarportStopBits | read-write | mandatory | Number of stop bits for the serial port. |
| 1.3.6.1.4.1.2.3.51.2.4.1.3 | NoderemoteAlertIds | |||
| 1.3.6.1.4.1.2.3.51.2.4.1.3.1 | TableremoteAlertIdsTable | not-accessible | mandatory | Table of remote alert entries. This table lets you configure remote alert recipients. You can define up to 12 unique recipients. NOTE: All selected alert event… |
| 1.3.6.1.4.1.2.3.51.2.4.1.3.1.1 | RowremoteAlertIdsEntry | not-accessible | mandatory | Remote alert entries. |
| 1.3.6.1.4.1.2.3.51.2.4.1.3.1.1.1 | ColumnremoteAlertIdEntryIndex | read-only | mandatory | Index for remote alert entry. |
| 1.3.6.1.4.1.2.3.51.2.4.1.3.1.1.2 | ColumnremoteAlertIdEntryStatus | read-write | mandatory | Remote alert entry status, invalid means entry not defined yet, disabledAndValid means entry defined but not enabled to send an alert, enabledAndValid means en… |
| 1.3.6.1.4.1.2.3.51.2.4.1.3.1.1.3 | ColumnremoteAlertIdEntryIpOrHostAddress | read-write | mandatory | A null terminated string that either contains an IP address of the form '1.2.3.4' or a host name (if DNS is enabled) for the alert entry. |
| 1.3.6.1.4.1.2.3.51.2.4.1.3.1.1.4 | ColumnremoteAlertIdEntryTextDescription | read-write | mandatory | A null terminated string that contains a text description of this entry. |
| 1.3.6.1.4.1.2.3.51.2.4.1.3.1.1.5 | ColumnremoteAlertIdEntryNotificationType | read-write | mandatory | Remote alert entry notification method. Types include unknown when the type can't be determined (read-only), snmpOverLan for an SNMP alert over ethernet, and e… |
| 1.3.6.1.4.1.2.3.51.2.4.1.3.1.1.9 | ColumnremoteAlertIdEmailAddr | read-write | mandatory | A null terminated string that contains an E-Mail Address. For example, 'xyz@us.ibm.com'. Used only for an E-mail over LAN notification type. |
| 1.3.6.1.4.1.2.3.51.2.4.1.3.1.1.13 | ColumnremoteAlertIdEntrySelectiveAlert | read-write | mandatory | Remote alert entry selective alert setting. A value of critOnlyAlerts will only send critical alerts to this remote alert recipient, a value of allAlerts will … |
| 1.3.6.1.4.1.2.3.51.2.4.1.3.30 | ScalargenerateTestAlert | read-write | mandatory | Generate a Test Alert. This will send a test alert to all configured and enabled remote alert recipients. NOTE: Value returned for the GET command is meaningle… |
| 1.3.6.1.4.1.2.3.51.2.4.1.4 | NoderemoteAccessIds | |||
| 1.3.6.1.4.1.2.3.51.2.4.1.4.1 | TableremoteAccessIdsTable | not-accessible | mandatory | Table of remote access profiles. This table lets you to configure all login profiles. NOTE: By default, the management module comes configured with one login p… |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1 | RowremoteAccessIdsEntry | not-accessible | mandatory | Remote access entries. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.1 | ColumnremoteAccessIdEntryIndex | read-only | mandatory | Index for Remote access entry. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.2 | ColumnremoteAccessIdEntryUserId | read-write | mandatory | Remote access entry null terminated string that contains the userid. It must not be a duplicate of any previously configured ones. This field is only allowed t… |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.3 | ColumnremoteAccessIdEntryPassword | read-write | mandatory | Remote access password. The password rules are dictated by a combination of the chassis security policy setting (securityPolicySetting) and the user account se… |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.10 | ColumnremoteAccessIdEntryPermgroups | read-write | mandatory | A list of permission groups for this userid, delmited with a '|' |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.11 | ColumnremoteAccessIdEntryLoggedIn | read-only | mandatory | Indicates if user is currently logged in or not. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.12 | ColumnremoteAccessIdEntryLastLogin | read-only | mandatory | Timestamp for the last successful login by the user. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.13 | ColumnremoteAccessIdEntryPwdCompliant | read-only | mandatory | Indicates if user complies with all of the password rules currently in effect. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.14 | ColumnremoteAccessIdEntryPwdExp | read-only | mandatory | The number of days until the user's current password expires. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.15 | ColumnremoteAccessIdEntryDormant | read-only | mandatory | Indicates if the user account has been inactive for a specified amount of time based on inactivityAlertDisablePeriod in the customSecuritySettings section. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.16 | ColumnremoteAccessIdEntryState | read-only | mandatory | Indicates the state of the user: Active - normal state Disabled - user cannot use account until enabled by a supervisor or chassis user account manager. An acc… |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.17 | ColumnremoteAccessIdEntryAction | read-write | mandatory | Actions that only a supervisor or chassis user account manager can perform for each user id: Enable - enables an account in the Disabled state Disable - disabl… |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.18 | ColumnremoteAccessIdEntrySessionCount | read-only | mandatory | The number of sessions the user is currently logged in to. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.19 | ColumnremoteAccessIdEntryMaxSessions | read-write | mandatory | The maximum number of simultaneous active sessions allowed for the user. If the value is 0, this option is disabled. The minimum value is 1 and the maximum val… |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.20 | ColumnremoteAccessIdEntryStatus | read-write | mandatory | This object manages the creation and deletion of this entry. The steps recommended to add a new group are: 1. Create a new entry in this table remoteAccessIdEn… |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.21 | ColumnremoteAccessIdEntryIPMIProvisioned | read-write | mandatory | Indicates if the user has been provisioned as an IPMI account. If this is user is provisioned as an IPMI account, the nodes (scope) and authorities will be det… |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.22 | ColumnremoteAccessIdEntrySNMPv3Provisioned | read-write | mandatory | Indicates if the user has been provisioned as an SNMPv3 account. If this is user is provisioned as an SNMPv3 account, the nodes (scope) and authorities will be… |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.3 | TableremoteAccessRBSroleTable | not-accessible | mandatory | Table of RBS User Role profiles. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1 | RowremoteAccessRBSroleEntry | not-accessible | mandatory | User Role entries. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.1 | ColumnroleIndex | read-only | mandatory | Index for RBS User Role entry. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.2 | ColumnroleId | read-write | mandatory | Remote access RBS role entry null terminated string that contains the permission group ID. It must not be a duplicate of any previously configured ones. This f… |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.3 | ColumnrbsSupervisor | read-write | mandatory | User has no restrictions. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.4 | ColumnrbsOperator | read-write | mandatory | User has read-only access, and cannot perform any save, modify, clear, or state affecting operations (e.g. restart MM, restore defaults, upgrade the firmware, … |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.5 | ColumnrbsChassisOperator | read-write | mandatory | User has ability to browse status and properties of chassis components (MM, chassis fans, midplane, power modules). Ability to backup MM configuration to a fil… |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.6 | ColumnrbsChassisAccountManagement | read-write | mandatory | User can add/modify/delete user login profiles. Ability to backup MM configuration to a file. Changing global login settings require chassis configuration auth… |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.7 | ColumnrbsChassisLogManagement | read-write | mandatory | User has ability to clear the MM event log, change log policy settings, and backup MM configuration to a file. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.8 | ColumnrbsChassisConfiguration | read-write | mandatory | User can modify and save any chassis configuration parameter (except user profiles and event log settings). Ability to restore MM factory defaults if the user … |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.9 | ColumnrbsChassisAdministration | read-write | mandatory | User has ability to do MM firmware updates, modify chassis LEDs, restore MM factory defaults if the user also has chassis configuration permissions. Ability to… |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.10 | ColumnrbsBladeOperator | read-write | mandatory | User has ability to browse status and properties of blades. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.11 | ColumnrbsBladeRemotePresence | read-write | mandatory | User has ability to access the blades remote console. The ability to issue the CLI console command to start an SOL session to a blade will also require this au… |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.12 | ColumnrbsBladeConfiguration | read-write | mandatory | User can modify and save any blade configuration parameter. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.13 | ColumnrbsBladeAdministration | read-write | mandatory | User can power on/off and restart blades, activate standby blades, do firmware updates, and modify blade LEDs. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.14 | ColumnrbsSwitchModuleOperator | read-write | mandatory | User has ability to browse status and properties of I/O Modules, and to ping I/O Modules. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.15 | ColumnrbsSwitchModuleConfiguration | read-write | mandatory | User can modify the I/O Module IP address, configure I/O Module Advanced Management parameters, and restore factory defaults on an I/O Module. Note that a user… |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.16 | ColumnrbsSwitchModuleAdministration | read-write | mandatory | User can power on/off and restart the I/O Modules, update I/O Module firmware, enable/disable the Fast POST and External Ports of an I/O Module. Note that a us… |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.23 | ColumnrbsEntryStatus | read-write | mandatory | This object manages the creation and deletion of this entry. The steps recommended to add a new group are: 1. Create a new entry in this table rbsEntryStatus =… |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4 | TableremoteAccessRBSscopeTable | not-accessible | mandatory | Table of RBS User Scope profiles. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1 | RowremoteAccessRBSscopeEntry | not-accessible | mandatory | User Scope entries. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.1 | ColumnscopeIndex | read-only | mandatory | Index for RBS User Scope Entry. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.2 | ColumnscopeId | read-only | mandatory | Remote access RBS scope entry null terminated string that contains the permission group ID. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.3 | ColumnrbsChassis | read-write | mandatory | User has access to the MM and chassis functions. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.4 | ColumnrbsBlade1 | read-write | mandatory | User has access to the blade in slot 1. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.5 | ColumnrbsBlade2 | read-write | mandatory | User has access to the blade in slot 2. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.6 | ColumnrbsBlade3 | read-write | mandatory | User has access to the blade in slot 3. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.7 | ColumnrbsBlade4 | read-write | mandatory | User has access to the blade in slot 4. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.8 | ColumnrbsBlade5 | read-write | mandatory | User has access to the blade in slot 5. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.9 | ColumnrbsBlade6 | read-write | mandatory | User has access to the blade in slot 6. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.10 | ColumnrbsBlade7 | read-write | mandatory | User has access to the blade in slot 7. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.11 | ColumnrbsBlade8 | read-write | mandatory | User has access to the blade in slot 8. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.12 | ColumnrbsBlade9 | read-write | mandatory | User has access to the blade in slot 9. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.13 | ColumnrbsBlade10 | read-write | mandatory | User has access to the blade in slot 10. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.14 | ColumnrbsBlade11 | read-write | mandatory | User has access to the blade in slot 11. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.15 | ColumnrbsBlade12 | read-write | mandatory | User has access to the blade in slot 12. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.16 | ColumnrbsBlade13 | read-write | mandatory | User has access to the blade in slot 13. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.17 | ColumnrbsBlade14 | read-write | mandatory | User has access to the blade in slot 14. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.18 | ColumnrbsSwitch1 | read-write | mandatory | User has access to I/O module 1. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.19 | ColumnrbsSwitch2 | read-write | mandatory | User has access to I/O module 2. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.20 | ColumnrbsSwitch3 | read-write | mandatory | User has access to I/O module 3. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.21 | ColumnrbsSwitch4 | read-write | mandatory | User has access to I/O module 4. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.22 | ColumnrbsSwitch5 | read-write | mandatory | User has access to I/O module 5. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.23 | ColumnrbsSwitch6 | read-write | mandatory | User has access to I/O module 6. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.24 | ColumnrbsSwitch7 | read-write | mandatory | User has access to I/O module 7. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.25 | ColumnrbsSwitch8 | read-write | mandatory | User has access to I/O module 8. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.26 | ColumnrbsSwitch9 | read-write | mandatory | User has access to I/O module 9. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.27 | ColumnrbsSwitch10 | read-write | mandatory | User has access to I/O module 10. |
| 1.3.6.1.4.1.2.3.51.2.4.1.4.9 | ScalarcmmCentralManagerIPMISNMPv3 | read-write | mandatory | Indicates whether CMM is the central manager of the IPMI and SNMPv3 accounts. For a write, it can only be set to enabled. Once the CMM state is enabled, it can… |
| 1.3.6.1.4.1.2.3.51.2.4.1.5 | NodeuserInterfaces | |||
| 1.3.6.1.4.1.2.3.51.2.4.1.5.1 | Scalarcli | read-write | mandatory | Enable/Disable CLI access to the MM (telnet and SSH). The value enabled(3) means both telnet and ssh are enabled. |
| 1.3.6.1.4.1.2.3.51.2.4.1.5.2 | Scalarsnmp | read-write | mandatory | Enable/Disable SNMP v1 and v3 access to the MM. The value enabled(3) means both telnet and ssh are enabled. |
| 1.3.6.1.4.1.2.3.51.2.4.1.5.3 | Scalartcm | read-write | mandatory | Enable/Disable TCP command mode (TCM) access to the MM. A value of 0 means disabled, any value from 1 to 20 means enabled. NOTE: MM will provide a max of 20 co… |
| 1.3.6.1.4.1.2.3.51.2.4.1.5.4 | Scalarweb | read-write | mandatory | Enable/Disable Web access (HTTP/HTTPS) to the MM. NOTE: Disabling web access to the MM will cause all currently active web sessions to disconnect, and you will… |
| 1.3.6.1.4.1.2.3.51.2.4.1.5.5 | Scalarstcm | read-write | mandatory | Enable/Disable secure TCP command mode (STCM) access to the MM. A value of 0 means disabled, any value from 1 to 20 means enabled. NOTE: MM will provide a max … |
| 1.3.6.1.4.1.2.3.51.2.4.1.6 | NodemmSshClientAuth | |||
| 1.3.6.1.4.1.2.3.51.2.4.1.6.1 | TablemmSshClientAuthPubKeyTable | not-accessible | mandatory | A table that contains client authentication public key information. |
| 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1 | RowmmSshClientAuthPubKeyEntry | not-accessible | mandatory | A information list about a particular SSH public key used for client authentication. The primary table index is the same value as the associated remoteAccessId… |
| 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.1 | ColumnmmSshClientAuthRemoteAccessIdIndex | read-only | mandatory | The primary table index is the same value as the associated remoteAccessIdEntryIndex used as an index into the remoteAccessIdsTable. |
| 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.2 | ColumnmmSshClientAuthPubKeyIndex | read-only | mandatory | The secondary table index used to select one of the client authentication public keys for a particular remote access Id. The index is an integer value from 1 t… |
| 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.3 | ColumnmmSshClientAuthPubKeyType | read-only | mandatory | The type of the SSH public key represented by this entry. |
| 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.4 | ColumnmmSshClientAuthPubKeySize | read-only | mandatory | The size of the SSH public key represented by this entry. |
| 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.5 | ColumnmmSshClientAuthPubKeyFingerprint | read-only | mandatory | The RSA fingerprint of the SSH public key represented by this entry. This value can be used with the SSH client to verify, on the initial connection, that the … |
| 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.6 | ColumnmmSshClientAuthPubKeyAcceptFrom | read-write | mandatory | This is a filter that describes the set of SSH client IP addresses and host names that can establish SSH connections to the MM authenticated by the public key … |
| 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.7 | ColumnmmSshClientAuthPubKeyComment | read-write | mandatory | This is a descriptive string that the administrator may use to help identify the public key represented by this entry. It serves no function in the operation o… |
| 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.8 | ColumnmmSshClientAuthPubKeyAction | read-write | mandatory | import(1) starts the TFTP file transfer of an SSH client authentication public key from the TFTP server to the MM. The import operation is only accepted if the… |
| 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.9 | ColumnmmSshClientAuthPubKeyEntryStatus | read-write | mandatory | This object manages the creation and deletion of this entry. The steps recommended to install and to activate a new client authorization public key are: 1. Set… |
| 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.10 | ColumnmmSshClientAuthPubKeyUserId | read-only | mandatory | The userid for the key entry. |
| 1.3.6.1.4.1.2.3.51.2.4.1.6.2 | ScalarmmSshClientAuthPubKeyUnused | read-only | mandatory | The number of available storage locations that may be used to install additional Client Authentication Public Keys. This number decreases by one when a new key… |
| 1.3.6.1.4.1.2.3.51.2.4.1.6.3 | ScalarmmSshClientAuthPubKeyTftpServer | read-write | mandatory | IP address or host name of the TFTP server where an SSH client authentication public key is to be installed from or exported to. The address must be entered in… |
| 1.3.6.1.4.1.2.3.51.2.4.1.6.4 | ScalarmmSshClientAuthPubKeyFileName | read-write | mandatory | File name on the TFTP server of an SSH client authentication public key. |
| 1.3.6.1.4.1.2.3.51.2.4.1.6.5 | ScalarmmSshClientAuthPubKeyFileFormat | read-write | mandatory | File format of SSH client authentication public key files imported from or exported to the TFTP file server. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7 | NodegroupProfiles | |||
| 1.3.6.1.4.1.2.3.51.2.4.1.7.1 | TablegroupIdsTable | not-accessible | mandatory | Table of Group profiles. This table lets you to configure all group profiles. You can define up to 16 unique profiles. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.1.1 | RowgroupIdsEntry | not-accessible | mandatory | Group ID entries. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.1.1.1 | ColumngroupIndex | read-only | mandatory | Index for Group IDs entry. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.1.1.2 | ColumngroupId | read-write | mandatory | Group ID. It is a null terminated string that contains the group-id. It must not be a duplicate of any previously configured ones. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.1.1.3 | ColumngroupRole | read-only | mandatory | Group Role. It indicates if the group has supervisor, operator, or custom access. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.1.1.9 | ColumngroupEntryStatus | read-write | mandatory | This object manages the creation and deletion of this entry. The steps recommended to add a new group are: 1. Create a new entry in this table groupEntryStatus… |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.2 | TablegroupRBSroleTable | not-accessible | mandatory | Table of Group Role profiles. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1 | RowgroupRBSroleEntry | not-accessible | mandatory | Group Role entries. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.1 | ColumngroupRBSroleIndex | read-only | mandatory | Index for Group Role entry. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.2 | ColumngroupRBSroleId | read-only | mandatory | Group ID |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.3 | ColumngroupRBSSupervisor | read-write | mandatory | Group has no restrictions. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.4 | ColumngroupRBSOperator | read-write | mandatory | Group has read-only access, and cannot perform any save, modify, clear, or state affecting operations (e.g. restart MM, restore defaults, upgrade the firmware,… |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.5 | ColumngroupRBSChassisOperator | read-write | mandatory | Group has ability to browse status and properties of chassis components (MM, chassis fans, midplane, power modules). Ability to backup MM configuration to a fi… |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.6 | ColumngroupRBSChassisAccountManagement | read-write | mandatory | Group can add/modify/delete user login profiles. Ability to backup MM configuration to a file. Changing global login settings require chassis configuration aut… |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.7 | ColumngroupRBSChassisLogManagement | read-write | mandatory | Group has ability to clear the MM event log, change log policy settings, and backup MM configuration to a file. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.8 | ColumngroupRBSChassisConfiguration | read-write | mandatory | Group can modify and save any chassis configuration parameter (except user profiles and event log settings). Ability to restore MM factory defaults if the grou… |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.9 | ColumngroupRBSChassisAdministration | read-write | mandatory | Group has ability to do MM firmware updates, modify chassis LEDs, restore MM factory defaults if the group also has chassis configuration permissions. Ability … |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.10 | ColumngroupRBSBladeOperator | read-write | mandatory | Group has ability to browse status and properties of blades. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.11 | ColumngroupRBSBladeRemotePresence | read-write | mandatory | Group has ability to access the blade remote console The ability to issue the CLI console command to start an SOL session to a blade will also require this aut… |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.12 | ColumngroupRBSBladeConfiguration | read-write | mandatory | Group can modify and save any blade configuration parameter. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.13 | ColumngroupRBSBladeAdministration | read-write | mandatory | Group can power on/off and restart blades, activate standby blades, do firmware updates, and modify blade LEDs. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.14 | ColumngroupRBSSwitchModuleOperator | read-write | mandatory | Group has ability to browse status and properties of I/O Modules, and to ping I/O Modules. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.15 | ColumngroupRBSSwitchModuleConfiguration | read-write | mandatory | Group can modify the I/O Module IP address, configure I/O Module Advanced Management parameters, and restore factory defaults on an I/O Module. Note that a gro… |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.16 | ColumngroupRBSSwitchModuleAdministration | read-write | mandatory | Group can power on/off and restart the I/O Modules, update I/O Module firmware, enable/disable the Fast POST and External Ports of an I/O Module. Note that a g… |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3 | TablegroupRBSscopeTable | not-accessible | mandatory | Table of Group Scope profiles. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1 | RowgroupRBSscopeEntry | not-accessible | mandatory | Group Scope entries. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.1 | ColumngroupRBSscopeIndex | read-only | mandatory | Index for Group Scope Entry. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.2 | ColumngroupRBSscopeId | read-only | mandatory | Group ID |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.3 | ColumngroupRBSChassis | read-write | mandatory | Group has access to the MM and chassis functions. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.4 | ColumngroupRBSBlade1 | read-write | mandatory | Group has access to the blade in slot 1. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.5 | ColumngroupRBSBlade2 | read-write | mandatory | Group has access to the blade in slot 2. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.6 | ColumngroupRBSBlade3 | read-write | mandatory | Group has access to the blade in slot 3. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.7 | ColumngroupRBSBlade4 | read-write | mandatory | Group has access to the blade in slot 4. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.8 | ColumngroupRBSBlade5 | read-write | mandatory | Group has access to the blade in slot 5. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.9 | ColumngroupRBSBlade6 | read-write | mandatory | Group has access to the blade in slot 6. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.10 | ColumngroupRBSBlade7 | read-write | mandatory | Group has access to the blade in slot 7. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.11 | ColumngroupRBSBlade8 | read-write | mandatory | Group has access to the blade in slot 8. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.12 | ColumngroupRBSBlade9 | read-write | mandatory | Group has access to the blade in slot 9. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.13 | ColumngroupRBSBlade10 | read-write | mandatory | Group has access to the blade in slot 10. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.14 | ColumngroupRBSBlade11 | read-write | mandatory | Group has access to the blade in slot 11. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.15 | ColumngroupRBSBlade12 | read-write | mandatory | Group has access to the blade in slot 12. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.16 | ColumngroupRBSBlade13 | read-write | mandatory | Group has access to the blade in slot 13. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.17 | ColumngroupRBSBlade14 | read-write | mandatory | Group has access to the blade in slot 14. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.18 | ColumngroupRBSSwitch1 | read-write | mandatory | Group has access to I/O module 1. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.19 | ColumngroupRBSSwitch2 | read-write | mandatory | Group has access to I/O module 2. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.20 | ColumngroupRBSSwitch3 | read-write | mandatory | Group has access to I/O module 3. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.21 | ColumngroupRBSSwitch4 | read-write | mandatory | Group has access to I/O module 4. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.22 | ColumngroupRBSSwitch5 | read-write | mandatory | Group has access to I/O module 5. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.23 | ColumngroupRBSSwitch6 | read-write | mandatory | Group has access to I/O module 6. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.24 | ColumngroupRBSSwitch7 | read-write | mandatory | Group has access to I/O module 7. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.25 | ColumngroupRBSSwitch8 | read-write | mandatory | Group has access to I/O module 8. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.26 | ColumngroupRBSSwitch9 | read-write | mandatory | Group has access to I/O module 9. |
| 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.27 | ColumngroupRBSSwitch10 | read-write | mandatory | Group has access to I/O module 10. |
| 1.3.6.1.4.1.2.3.51.2.4.2 | NoderemoteAlerts | |||
| 1.3.6.1.4.1.2.3.51.2.4.2.1 | NoderemoteAlertsCrit | |||
| 1.3.6.1.4.1.2.3.51.2.4.2.1.5 | ScalarcritPower | read-write | mandatory | Generate an alert if any of the system power supplies fail. |
| 1.3.6.1.4.1.2.3.51.2.4.2.1.10 | ScalarcritBlade | read-write | mandatory | Generate an alert for any critical error condition on a blade. |
| 1.3.6.1.4.1.2.3.51.2.4.2.1.11 | ScalarcritIO | read-write | mandatory | Generate an alert for any critical error condition on I/O module. |
| 1.3.6.1.4.1.2.3.51.2.4.2.1.12 | ScalarcritStorage | read-write | mandatory | Generate an alert for any critical error condition on a Storage module. |
| 1.3.6.1.4.1.2.3.51.2.4.2.1.13 | ScalarcritChassis | read-write | mandatory | Generate an alert for any critical error condition on chassis. |
| 1.3.6.1.4.1.2.3.51.2.4.2.1.14 | ScalarcritFan | read-write | mandatory | Generate an alert for any critical error condition on cooling devices. |
| 1.3.6.1.4.1.2.3.51.2.4.2.2 | NoderemoteAlertsNonCrit | |||
| 1.3.6.1.4.1.2.3.51.2.4.2.2.10 | ScalarwarnLogFull | read-write | mandatory | Generate an alert if the system log reaches 100% full. |
| 1.3.6.1.4.1.2.3.51.2.4.2.2.15 | ScalarwarnBlade | read-write | mandatory | Generate an alert for any warning condition on a blade. |
| 1.3.6.1.4.1.2.3.51.2.4.2.2.16 | ScalarwarnIO | read-write | mandatory | Generate an alert for any warning condition on I/O module. |
| 1.3.6.1.4.1.2.3.51.2.4.2.2.17 | ScalarwarnStorage | read-write | mandatory | Generate an alert for any warning condition on a Storage module. |
| 1.3.6.1.4.1.2.3.51.2.4.2.2.18 | ScalarwarnPower | read-write | mandatory | Generate an alert for any warning condition on power module. |
| 1.3.6.1.4.1.2.3.51.2.4.2.2.19 | ScalarwarnChassis | read-write | mandatory | Generate an alert for any warning condition on chassis. |
| 1.3.6.1.4.1.2.3.51.2.4.2.2.20 | ScalarwarnFan | read-write | mandatory | Generate an alert for any warning condition on cooling devices. |
| 1.3.6.1.4.1.2.3.51.2.4.2.3 | NoderemoteAlertsSystem | |||
| 1.3.6.1.4.1.2.3.51.2.4.2.3.10 | ScalarsystemInventory | read-write | mandatory | Generate an alert if the a processor blade or media tray is added or removed. |
| 1.3.6.1.4.1.2.3.51.2.4.2.3.11 | ScalarsystemLog75PctFull | read-write | mandatory | Generate an alert if the system log reaches 75% full. |
| 1.3.6.1.4.1.2.3.51.2.4.2.3.12 | ScalarnetworkChangeNotification | read-write | mandatory | Generate an alert if the MM has restarted and the internal network has initialized successfully, or if an IP address change via a source other than the managem… |
| 1.3.6.1.4.1.2.3.51.2.4.2.3.15 | ScalarsystemRemoteLogin | read-write | mandatory | Generate an alert if the system detects a new user logged in from a remote site. |
| 1.3.6.1.4.1.2.3.51.2.4.2.3.16 | ScalarsystemBlade | read-write | mandatory | Generate an alert for any informational condition on a blade. |
| 1.3.6.1.4.1.2.3.51.2.4.2.3.17 | ScalarsystemIO | read-write | mandatory | Generate an alert for any informational condition on I/O module. |
| 1.3.6.1.4.1.2.3.51.2.4.2.3.18 | ScalarsystemStorage | read-write | mandatory | Generate an alert for any informational condition on a Storage module. |
| 1.3.6.1.4.1.2.3.51.2.4.2.3.19 | ScalarsystemPower | read-write | mandatory | Generate an alert for any informational condition on power module. |
| 1.3.6.1.4.1.2.3.51.2.4.2.3.20 | ScalarsystemChassis | read-write | mandatory | Generate an alert for any informational condition on chassis. |
| 1.3.6.1.4.1.2.3.51.2.4.2.3.21 | ScalarsystemFan | read-write | mandatory | Generate an alert for any informational condition on cooling device. |
| 1.3.6.1.4.1.2.3.51.2.4.2.3.22 | ScalarsystemPWRDO | read-write | mandatory | Generate an alert for any informational condition on power on and power off. |
| 1.3.6.1.4.1.2.3.51.2.4.3 | NodesecuritySettings | |||
| 1.3.6.1.4.1.2.3.51.2.4.3.2 | ScalartrespassWarning | read-write | mandatory | If enabled, a customizable trespass warning message is displayed via the Web and CLI interfaces. |
| 1.3.6.1.4.1.2.3.51.2.4.3.3 | ScalartrespassWarningDefault | read-write | mandatory | Reset the trespass warning to default value. NOTE: Value returned for the GET command is meaningless for this MIB object. |
| 1.3.6.1.4.1.2.3.51.2.4.3.4 | ScalartrespassMessage | read-write | mandatory | The value of the trespass warning message. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5 | NodechassisSecuritySettings | |||
| 1.3.6.1.4.1.2.3.51.2.4.3.5.1 | ScalarsecurityPolicySetting | read-write | mandatory | Determines chassis security policy. legacy mode(0) or secure mode(1). unknown(255) returned when policy can't be set or determined. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.2 | ScalarsecurityPolicyState | read-only | mandatory | Determines chassis security policy state. If pending(0), check securityPolicyStatusTable for details on actions needed, to make fully active. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.3 | TablesecurityPolicyStatusTable | not-accessible | mandatory | Table of pending security policy status. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.3.1 | RowsecurityPolicyStatusEntry | not-accessible | mandatory | Pending security policy status entry |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.3.1.1 | ColumnsecurityPolicyStatusIndex | read-only | mandatory | Pending Security policy status index. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.3.1.2 | ColumnsecurityPolicyStatusComponentType | read-only | mandatory | Indicates Component type and location with pending security status. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.3.1.3 | ColumnsecurityPolicyStatusBayId | read-only | mandatory | Bay location of specific component. NOTE: securityPolicyStatusComponentType enumeration also indicates location. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.3.1.4 | ColumnsecurityPolicyStatusSummary | read-only | mandatory | Summary of pending security status for the component. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.3.1.5 | ColumnsecurityPolicyStatusDetails | read-only | mandatory | Details of pending security status for the component. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.10 | Nodecryptography | |||
| 1.3.6.1.4.1.2.3.51.2.4.3.5.10.5 | ScalarcryptographySummary | read-only | mandatory | The current level and summary description of the cryptographic configuration. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.10.15 | ScalarcryptographyMode | read-write | mandatory | The NIST cryptographic mode setting. A successful setting of this object initiates a reboot of the CMM within a few seconds. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.10.18 | TablecryptographyModeDetailsTable | not-accessible | mandatory | A table of information indicating any NIST customization details and any reasons that the CMM cannot transition to the desired NIST mode. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.10.18.1 | RowcryptographyModeDetailsEntry | not-accessible | mandatory | Cryptography mode status entry |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.10.18.1.1 | ColumncryptographyModeDetailsIndex | read-only | mandatory | Cryptography mode details index. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.10.18.1.2 | ColumncryptographyModeDetailsType | read-only | mandatory | Indication of what type of message is reported for this entry. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.10.18.1.3 | ColumncryptographyModeDetailsDescription | read-only | mandatory | Message containing details for this cryptography entry. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.10.20 | TablecryptographyModeComponentTable | not-accessible | mandatory | A table of information listing any IOMs or nodes that require a firmware update in order for the CMM to transition to the new mode. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.10.20.1 | RowcryptographyModeComponentEntry | not-accessible | mandatory | Cryptography mode component entry |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.10.20.1.1 | ColumncryptographyModeComponentIndex | read-only | mandatory | Cryptography mode component index. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.10.20.1.2 | ColumncryptographyModeComponentId | read-only | mandatory | A component identifier for an IOM or node in the form: ts:mm. t(type), s(slot number), mm sub-slot number. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.10.25 | ScalarcryptographicCipher | read-write | mandatory | The cryptographic cipher suite setting. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.10.30 | TablecryptographyCipherComponentTable | not-accessible | mandatory | A table of information listing any IOMs or nodes that are out of compliance with regards to the cipher suite setting and are therefore preventing the CMM from … |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.10.30.1 | RowcryptographyCipherComponentEntry | not-accessible | mandatory | Cryptography cipher component entry |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.10.30.1.1 | ColumncryptographyCipherComponentIndex | read-only | mandatory | Cryptography cipher component index. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.10.30.1.2 | ColumncryptographyCipherComponentId | read-only | mandatory | A component identifier for an IOM or node in the form: ts:mm. t(type), s(slot number), mm sub-slot number. |
| 1.3.6.1.4.1.2.3.51.2.4.3.5.15 | ScalarcipherStrength | read-write | mandatory | Strength level of the NIST signing algorithm for certificate authority. None(0) indicates no signing algorithm has been set. When writing a new value to this o… |
| 1.3.6.1.4.1.2.3.51.2.4.4 | NodespClock | |||
| 1.3.6.1.4.1.2.3.51.2.4.4.1 | ScalarspClockDateAndTimeSetting | read-write | mandatory | MM clock date and time setting. A date-time specification for the local time of day. For example to set the date and time to March 4, 2001 at 06:00:00AM, set t… |
| 1.3.6.1.4.1.2.3.51.2.4.4.2 | ScalarspClockTimezoneSetting | read-write | mandatory | MM clock Greenwich Mean Time(GMT) offset and Daylight Saving Time(DST) settings. For write, the value must be a time zone listed in spClockTimezoneTable. The s… |
| 1.3.6.1.4.1.2.3.51.2.4.4.3 | TablespClockTimezoneTable | not-accessible | mandatory | Table of all time zones listed in zone.tab file |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1 | RowspClockTimezoneEntry | not-accessible | mandatory | Time zone entry |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.1 | ColumnspClockTimezoneIndex | read-only | mandatory | Time zone table index. |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.2 | ColumnspClockTimezoneId | read-only | mandatory | Time zone instance id. |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.3 | ColumnspClockTimezoneCaption | read-only | mandatory | Time zone caption. |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.4 | ColumnspClockTimezoneDescription | read-only | mandatory | Time zone description. |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.5 | ColumnspClockTimezoneName | read-only | mandatory | Time zone name. |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.6 | ColumnspClockTimezoneStandardName | read-only | mandatory | Time zone standard name. |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.7 | ColumnspClockTimezoneStandardCaption | read-only | mandatory | Time zone standard caption. |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.8 | ColumnspClockTimezoneDaylightName | read-only | mandatory | Time zone daylight name. |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.9 | ColumnspClockTimezoneDaylightCaption | read-only | mandatory | Time zone daylight caption. |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.10 | ColumnspClockTimezoneCmmOffset | read-only | mandatory | CMM offset. |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.11 | ColumnspClockTimezoneStandardOffsetMinutes | read-only | mandatory | Standard GMT offset in minutes. |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.12 | ColumnspClockTimezoneStandardDaylightOffsetMinutes | read-only | mandatory | Standard GMT offset in minutes. |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.13 | ColumnspClockTimezoneDaylightDay | read-only | mandatory | There are two different interpretations for this field, depending on the value of DaylightDayOfWeek. In one case, DaylightDay defines the day-in-month on which… |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.14 | ColumnspClockTimezoneDaylightDayOfWeek | read-only | mandatory | Day of week daylight saving begins. |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.15 | ColumnspClockTimezoneDaylightMonth | read-only | mandatory | Month daylight saving begins. |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.16 | ColumnspClockTimezoneDaylightStandardDay | read-only | mandatory | There are two different interpretations for this property, depending on the value of StandardDayOfWeek. In one case, StandardDay defines the day-in-month on wh… |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.17 | ColumnspClockTimezoneDaylightStandardDayOfWeek | read-only | mandatory | Day of week daylight saving ends. |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.18 | ColumnspClockTimezoneDaylightStandardMonth | read-only | mandatory | Month daylight saving ends. |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.19 | ColumnspClockTimezoneDaylightIntervalInMinutes | read-only | mandatory | Interval in minutes (Daylight saving begins). |
| 1.3.6.1.4.1.2.3.51.2.4.4.3.1.20 | ColumnspClockTimezoneDaylightStandardInMinutes | read-only | mandatory | Interval in minutes (Daylight saving ends). |
| 1.3.6.1.4.1.2.3.51.2.4.4.5 | ScalarspClockTimezoneDaylightStart | read-only | mandatory | DST start. |
| 1.3.6.1.4.1.2.3.51.2.4.4.6 | ScalarspClockTimezoneDaylightEnd | read-only | mandatory | DST end. |
| 1.3.6.1.4.1.2.3.51.2.4.5 | NodespIdentification | |||
| 1.3.6.1.4.1.2.3.51.2.4.5.1 | ScalarspTxtId | read-write | mandatory | Text description of the MM. NOTE: Do not put any 'space characters' at end of the string. |
| 1.3.6.1.4.1.2.3.51.2.4.9 | NodenetworkConfiguration | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.1 | NodenetworkInterfaces | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1 | NodeextEthernetInterface | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.1 | ScalarextEthernetInterfaceType | read-only | mandatory | The type of interface. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.3 | ScalarextEthernetInterfaceHostName | read-write | mandatory | Contains the 64 byte null terminated DNS host name for this interface. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.4 | ScalarextEthernetInterfaceIPAddress | read-write | mandatory | Contains the IP address for the ethernet interface. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.5 | ScalarextEthernetInterfaceDataRate | read-write | mandatory | Specifies the data transfer rate to be used over the ethernet interface: 10Mb, 100Mb, 1G or Auto. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.6 | ScalarextEthernetInterfaceDuplexSetting | read-write | mandatory | Specifies the duplex settings for the data transfer rate to be used over the ethernet interface: Half, Full, or Auto. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.7 | ScalarextEthernetInterfaceLAA | read-write | mandatory | Specifies the locally administered MAC address. The locally administered address must be a hexadecimal value between 000000000000 - FFFFFFFFFFFF. This value mu… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.8 | ScalarextEthernetInterfaceDhcpEnabled | read-write | mandatory | Disable or enable DHCP on this interface. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.9 | ScalarextEthernetInterfaceGatewayIPAddress | read-write | mandatory | Contains the IP address of the gateway/router for the ethernet interface. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.10 | ScalarextEthernetInterfaceBIA | read-only | mandatory | Specifies the burned-in MAC (BIA) address. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.13 | ScalarextEthernetInterfaceMTU | read-write | mandatory | Contains the Maximum Transmission Unit(MTU) for the ethernet interface |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.14 | ScalarextEthernetInterfaceSubnetMask | read-write | mandatory | Contains the subnet mask for the ethernet interface |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16 | NodedhcpEthernetInterface | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16.1 | ScalardhcpHostName | read-only | mandatory | Contains the 64 byte null terminated DNS host name for this interface, assigned by the DHCP server. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16.2 | ScalardhcpIPAddress | read-only | mandatory | Contains the IP address for the ethernet interface, assigned by the DHCP server. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16.3 | ScalardhcpGatewayIPAddress | read-only | mandatory | Contains the IP address of the gateway/router for the ethernet interface, assigned by the DHCP server. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16.4 | ScalardhcpSubnetMask | read-only | mandatory | Contains the Subnet Mask for the ethernet interface, assigned by the DHCP server. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16.5 | ScalardhcpDomainName | read-only | mandatory | Contains the 64 byte null terminated Domain Name for this interface, assigned by the DHCP server. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16.6 | ScalardhcpDHCPServer | read-only | mandatory | Contains the DHCP server IP address used to acquire the DHCP settings. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16.7 | ScalardhcpPrimaryDNSServer | read-only | mandatory | Contains the Primary DNS server, assigned by the DHCP server. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16.8 | ScalardhcpSecondaryDNSServer | read-only | mandatory | Contains the Secondary DNS server, assigned by the DHCP server. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16.9 | ScalardhcpTertiaryDNSServer | read-only | mandatory | Contains the tertiary DNS server, assigned by the DHCP server. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.1.22 | ScalarextEthernetInterfaceFloatingIPAddress | read-write | mandatory | Contains the floating IP address for the external ethernet interface. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3 | NodestandbyExtEthernetInterface | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.1 | ScalarstandbyExtEthernetInterfaceType | read-only | mandatory | The type of interface. NOTE: This MIB object is only applicable to systems with a standby MM. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.3 | ScalarstandbyExtEthernetInterfaceHostName | read-write | mandatory | Contains the 64 byte null terminated DNS host name for this interface. NOTE: This MIB object is only applicable to systems with a standby MM. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.4 | ScalarstandbyExtEthernetInterfaceIPAddress | read-write | mandatory | Contains the IP address for the ethernet interface. NOTE: This MIB object is only applicable to systems with a standby MM. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.5 | ScalarstandbyExtEthernetInterfaceDataRate | read-write | mandatory | Specifies the data transfer rate to be used over the ethernet interface: 10Mb, 100Mb, 1G or Auto. NOTE: This MIB object is only applicable to systems with a st… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.6 | ScalarstandbyExtEthernetInterfaceDuplexSetting | read-write | mandatory | Specifies the duplex settings for the data transfer rate to be used over the ethernet interface: Half, Full, or Auto. NOTE: This MIB object is only applicable … |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.7 | ScalarstandbyExtEthernetInterfaceLAA | read-write | mandatory | Specifies the locally administered MAC address. The locally administered address must be a hexadecimal value between 000000000000 - FFFFFFFFFFFF. This value mu… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.8 | ScalarstandbyExtEthernetInterfaceDhcpEnabled | read-write | mandatory | Disable or enable DHCP on this interface. NOTE: This MIB object is only applicable to systems with a standby MM. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.9 | ScalarstandbyExtEthernetInterfaceGatewayIPAddress | read-write | mandatory | Contains the IP address of the gateway/router for the ethernet interface. NOTE: This MIB object is only applicable to systems with a standby MM. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.10 | ScalarstandbyExtEthernetInterfaceBIA | read-only | mandatory | Specifies the burned-in MAC (BIA) address. NOTE: This MIB object is only applicable to systems with a standby MM. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.13 | ScalarstandbyExtEthernetInterfaceMTU | read-write | mandatory | Contains the Maximum Transmission Unit (MTU) for the ethernet interface. NOTE: This MIB object is only applicable to systems with a standby MM. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.14 | ScalarstandbyExtEthernetInterfaceSubnetMask | read-write | mandatory | Contains the subnet mask for the ethernet interface. NOTE: This MIB object is only applicable to systems with a standby MM. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.15 | ScalaradvancedFailover | read-write | mandatory | User can enable advanced failover. off : no standby network interface ipswap: Standby network interface, swap IPs during failover ipnoswap: Standby network int… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16 | NodestandbyDhcpEthernetInterface | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16.1 | ScalarstandbyDhcpHostName | read-only | mandatory | Contains the 64 byte null terminated DNS host name for this interface, assigned by the DHCP server. NOTE: This MIB object is only applicable to systems with a … |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16.2 | ScalarstandbyDhcpIPAddress | read-only | mandatory | Contains the IP address for the ethernet interface, assigned by the DHCP server. NOTE: This MIB object is only applicable to systems with a standby MM. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16.3 | ScalarstandbyDhcpGatewayIPAddress | read-only | mandatory | Contains the IP address of the gateway/router for the ethernet interface, assigned by the DHCP server. NOTE: This MIB object is only applicable to systems with… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16.4 | ScalarstandbyDhcpSubnetMask | read-only | mandatory | Contains the Subnet Mask for the ethernet interface, assigned by the DHCP server. NOTE: This MIB object is only applicable to systems with a standby MM. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16.5 | ScalarstandbyDhcpDomainName | read-only | mandatory | Contains the 64 byte null terminated Domain Name for this interface, assigned by the DHCP server. NOTE: This MIB object is only applicable to systems with a st… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16.6 | ScalarstandbyDhcpDHCPServer | read-only | mandatory | Contains the DHCP server IP address used to acquire the DHCP settings. NOTE: This MIB object is only applicable to systems with a standby MM. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16.7 | ScalarstandbyDhcpPrimaryDNSServer | read-only | mandatory | Contains the Primary DNS server, assigned by the DHCP server. NOTE: This MIB object is only applicable to systems with a standby MM. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16.8 | ScalarstandbyDhcpSecondaryDNSServer | read-only | mandatory | Contains the Secondary DNS server, assigned by the DHCP server. NOTE: This MIB object is only applicable to systems with a standby MM. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16.9 | ScalarstandbyDhcpTertiaryDNSServer | read-only | mandatory | Contains the tertiary DNS server, assigned by the DHCP server. NOTE: This MIB object is only applicable to systems with a standby MM. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4 | NodeextEthernetInterfaceIPv6 | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.1 | ScalarextEthernetInterfaceIPv6Type | read-only | mandatory | The type of interface. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.2 | ScalarextEthernetInterfaceIPv6Enabled | read-write | mandatory | The current IPv6 enabled or disabled state of this MM. NOTE: If IPv6 address(es) have been configured for one or more interfaces/protocols/services on this MM,… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5 | NodeextEthernetInterfaceIPv6Config | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.1 | NodeextEthernetInterfaceIPv6LocalAddress | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.1.1 | ScalarextEthernetInterfaceIPv6LinkLocalAddress | read-only | mandatory | The IPv6 link local IP address for the ethernet interface. NOTE: If extEthernetInterfaceIPv6Enabled is currently disabled, this object has the value '0:0:0:0:0… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.2 | NodeextEthernetInterfaceIPv6StaticIPConfig | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.2.1 | ScalarextEthernetInterfaceIPv6StaticIPConfigEnabled | read-write | mandatory | The IPv6 static IP address enabled or disabled state for the ethernet interface. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.2.2 | ScalarextEthernetInterfaceIPv6StaticIPAddress | read-write | mandatory | The IPv6 static IP address for the ethernet interface. NOTE: If extEthernetInterfaceIPv6Enabled is currently disabled, this object has the value '0:0:0:0:0:0:0… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.2.3 | ScalarextEthernetInterfaceIPv6StaticIPAddressPrefixLen | read-write | mandatory | The IPv6 static IP address prefix length for the ethernet interface. NOTE: If extEthernetInterfaceIPv6Enabled is currently disabled, this object has the value … |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.2.4 | ScalarextEthernetInterfaceIPv6StaticIPDefaultRoute | read-write | mandatory | The IPv6 static IP address default route for the ethernet interface. NOTE: If extEthernetInterfaceIPv6Enabled is currently disabled, this object has the value … |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.2.5 | ScalarextEthernetInterfaceIPv6LinkFloatingAddress | read-write | mandatory | The IPv6 floating IP address for the external ethernet interface. NOTE: If extEthernetInterfaceIPv6Enabled is currently disabled, this object has the value '0:… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3 | NodeextEthernetInterfaceIPv6AutoIPConfig | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.1 | ScalarextEthernetInterfaceIPv6AutoIPConfigEnabled | read-write | mandatory | The IPv6 automatic IP configuration enabled or disabled state for the ethernet interface. NOTE: extEthernetInterfaceIPv6AutoIPConfigEnabled is the logical OR o… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.2 | NodeextEthernetInterfaceDHCPv6Config | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.2.1 | ScalarextEthernetInterfaceDHCPv6Enabled | read-write | mandatory | The DHCPv6 enabled or disabled state for the ethernet interface. NOTE: If extEthernetInterfaceIPv6StatelessAutoConfigEnabled is currently disabled, Disabling e… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.2.2 | ScalarextEthernetInterfaceDHCPv6IPAddress | read-only | mandatory | The IPv6 address for the ethernet interface, assigned by DHCPv6 server. NOTE: If extEthernetInterfaceIPv6Enabled or extEthernetInterfaceDHCPv6Enabled is disabl… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.2.4 | ScalarextEthernetInterfaceDHCPv6DomainName | read-only | mandatory | The 64 byte Domain Name for the ethernet interface, assigned by the DHCPv6 server. NOTE: If extEthernetInterfaceIPv6Enabled or extEthernetInterfaceDHCPv6Enable… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.2.5 | ScalarextEthernetInterfaceDHCPv6PrimaryDNSServer | read-only | mandatory | The primary DNS server, assigned by the DHCPv6 server. NOTE: If extEthernetInterfaceIPv6Enabled or extEthernetInterfaceDHCPv6Enabled is disabled or if DHCPv6 s… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.2.6 | ScalarextEthernetInterfaceDHCPv6SecondaryDNSServer | read-only | mandatory | The secondary DNS server, assigned by the DHCPv6 server. NOTE: If extEthernetInterfaceIPv6Enabled or extEthernetInterfaceDHCPv6Enabled is disabled or if DHCPv6… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.2.7 | ScalarextEthernetInterfaceDHCPv6TertiaryDNSServer | read-only | mandatory | The tertiary DNS server, assigned by the DHCPv6 server. NOTE: If extEthernetInterfaceIPv6Enabled or extEthernetInterfaceDHCPv6Enabled is disabled or if DHCPv6 … |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.2.8 | ScalarextEthernetInterfaceDHCPv6Server | read-only | mandatory | The DHCPv6 server IPv6 address used to acquire the DHCP settings. NOTE: If extEthernetInterfaceIPv6Enabled or extEthernetInterfaceDHCPv6Enabled is disabled or … |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.3 | NodeextEthernetInterfaceIPv6StatelessAutoConfig | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.3.1 | ScalarextEthernetInterfaceIPv6StatelessAutoConfigEnabled | read-write | mandatory | The IPv6 stateless auto-configuration enabled or disabled state for the ethernet interface. NOTE: If extEthernetfInterfaceDHCPv6Enabled is currently disabled, … |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.3.2 | TableextEthernetInterfaceStatelessAutoConfigAddressesTable | not-accessible | mandatory | Table of stateless Auto-Config addresses entries |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.3.2.1 | RowextEthernetInterfaceStatelessAutoConfigAddressesEntry | not-accessible | mandatory | Stateless Auto-Config address entries |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.3.2.1.1 | ColumnextEthernetInterfaceStatelessAutoConfigAddressesIndex | read-only | mandatory | Index for stateless Auto-Config addresses. NOTE: If extEthernetInterfaceIPv6StatelessAutoConfigEnabled or extEthernetInterfaceIPv6Enabled is currently disabled… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.3.2.1.2 | ColumnextEthernetInterfaceStatelessAutoConfigAddresses | read-only | mandatory | The stateless Auto-Configuration IPv6 address. NOTE: If extEthernetInterfaceIPv6StatelessAutoConfigEnabled or extEthernetInterfaceIPv6Enabled is currently disa… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.3.2.1.3 | ColumnextEthernetInterfaceStatelessAutoConfigAddressesPrefixLen | read-only | mandatory | The stateless Auto-Configration address prefix length. NOTE: If extEthernetInterfaceIPv6StatelessAutoConfigEnabled or extEthernetInterfaceIPv6Enabled is curren… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.5 | NodestandbyExtEthernetInterfaceIPv6 | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.1.5.1 | NodestandbyEthernetInterfaceIPv6LocalAddress | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.1.5.1.1 | ScalarstandbyEthernetInterfaceIPv6LinkLocalAddress | read-only | mandatory | The IPv6 link local IP address for the standby MM. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.5.2 | NodestandbyEthernetInterfaceIPv6StaticIPConfig | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.1.5.2.1 | ScalarstandbyEthernetInterfaceIPv6StaticIPConfigEnabled | read-only | mandatory | The IPv6 static IP address state for the MM. NOTE: This value may be altered through the extEthernetInterfaceIPv6StaticIPConfigEnabled object. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.5.2.2 | ScalarstandbyEthernetInterfaceIPv6StaticIPAddress | read-write | mandatory | The IPv6 static IP address for the standby MM NOTE: If extEthernetInterfaceIPv6Enabled is currently disabled, this object has the value '0:0:0:0:0:0:0:0'. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.5.2.3 | ScalarstandbyEthernetInterfaceIPv6StaticIPAddressPrefixLen | read-only | mandatory | The IPv6 static IP address prefix length for the standyby MM. NOTE: This value may be altered through the extEthernetInterfaceIPv6StaticIPAddressPrefixLen obje… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.5.2.4 | ScalarstandbyEthernetInterfaceIPv6StaticIPDefaultRoute | read-only | mandatory | The IPv6 static IP address default route for the standby MM. NOTE: This value may be altered through the extEthernetInterfaceIPv6StaticIPDefaultRoute object. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.5.3 | NodestandbyEthernetInterfaceDHCPv6Config | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.1.5.3.1 | ScalarstandbyEthernetInterfaceDHCPv6Enabled | read-only | mandatory | The DHCPv6 enabled or disabled state for the standby MM. NOTE: This field may be altered through the extEthernetInterfaceDHCPv6Enabled object. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.5.3.2 | ScalarstandbyEthernetInterfaceDHCPv6IPAddress | read-only | mandatory | The IPv6 address for the standby MM assigned by DHCPv6 server. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.5.3.4 | ScalarstandbyEthernetInterfaceDHCPv6DomainName | read-only | mandatory | The 64 byte Domain Name for the standby MM assigned by the DHCPv6 server. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.5.4 | TablestandbyEthernetInterfaceStatelessAutoConfigAddressesTable | not-accessible | mandatory | Table of stateless Auto-Config addresses entries. NOTE: If extEthernetInterfaceIPv6StatelessAutoConfigEnabled or extEthernetInterfaceIPv6Enabled is currently d… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.5.4.1 | RowstandbyEthernetInterfaceStatelessAutoConfigAddressesEntry | not-accessible | mandatory | Stateless Auto-Config address entries |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.5.4.1.1 | ColumnstandbyEthernetInterfaceStatelessAutoConfigAddressesIndex | read-only | mandatory | Index for stateless Auto-Config addresses. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.5.4.1.2 | ColumnstandbyEthernetInterfaceStatelessAutoConfigAddresses | read-only | mandatory | The stateless Auto-Configuration IPv6 address. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.5.4.1.3 | ColumnstandbyEthernetInterfaceStatelessAutoConfigAddressesPrefixLen | read-only | mandatory | The stateless Auto-Configration address prefix length. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.10 | ScalarddnsStatus | read-write | mandatory | Dynamic DNS provides the capability for a networked device to notify a domain name server to change, in real time, the active DNS configuration of its configur… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.11 | ScalarhostName | read-write | mandatory | Contains the DNS host name for this system. This object provides the exact same function as extEthernetInterfaceHostName |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.12 | ScalarstandbyHostName | read-write | mandatory | Contains the DNS host name for the standby. This object provides the exact same function as standbyExtEthernetInterfaceHostName and is only applicable to syste… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.13 | ScalardomainName | read-write | mandatory | The user assigned DNS domain name. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.14 | ScalarstandbyDomainName | read-write | mandatory | The user assigned DNS domain name of the standby. This is only applicable to systems with a standby MM. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.16 | ScalaractivateNetworkUpdates | read-write | mandatory | When read, the return value indicates if there are any pending network updates ready to be applied. Writing any value will apply any pending network updates im… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20 | NodevlanConfigure | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.1 | ScalarvlanGlobalState | read-write | mandatory | This object disables or enables the VLAN feature. The configuration objects for the VLAN are in the vlanCMMTable. The default setting for this object is disabl… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.2 | ScalarvlanCommitTimeout | read-write | mandatory | This object is the number of minutes from the last VLAN-related object change until any non-committed changes will revert back to their previous settings. This… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.3 | ScalarvlanCommitState | read-write | mandatory | This object gives the status of whether there are VLAN-related changes pending that need to be committed, and allows a user to commit (save) any VLAN changes. … |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20 | TablevlanCMMTable | not-accessible | mandatory | This table contains the VLAN configuration objects. The default entry has an vlanCMMIndex equal to 1. The objects for this default entry are configurable. An a… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1 | RowvlanCMMEntry | not-accessible | mandatory | VLAN entries. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.1 | ColumnvlanCMMIndex | read-only | mandatory | Index for VLAN entry. If vlanCMMIndex is equal to 1, it is the Default VLAN entry and cannot be deleted. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.2 | ColumnvlanCMMVlanId | read-write | mandatory | Valid VLAN ID. Allowed values are 5..4094. If the entry is not valid, this object will have the value of 0. If this entry has the vlanCMMIndex value of 1 (defa… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.3 | ColumnvlanCMMName | read-write | mandatory | This object allows the user to configure a text string name for this VLAN entry. This entry name is only used as a label for this entry. |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.4 | ColumnvlanCMMEntryStatus | read-write | mandatory | This object manages the creation and deletion of this entry. The steps recommended to add a new VLAN entry are: 1. Create a new entry in this table vlanCMMEntr… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.5 | ColumnvlanCMMState | read-write | mandatory | This object indicates whether this VLAN entry is enabled or disabled and allows the user to disable, enable or restart this entry except for the exceptions not… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.6 | ColumnvlanCMMSOLAccess | read-write | mandatory | This object allows the user to set whether the VLAN for this entry will have access to the Serial Over LAN (SOL) interface. Only one VLAN entry may have this o… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.8 | ColumnvlanCMMTagging | read-write | mandatory | This object allows the user to set whether VLAN tagging is enabled for this VLAN entry. This object is only configurable for the entry with the vlanCMMIndex va… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.31 | ColumnvlanCMMIPv4Address | read-write | mandatory | This object sets the IPv4 address for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will have this object set to the IP addr… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.32 | ColumnvlanCMMIPv4Gateway | read-write | mandatory | This object sets the IPv4 address for the IP gateway for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will have this object… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.33 | ColumnvlanCMMIPv4Mask | read-write | mandatory | This object sets the IPv4 subnet mask for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will have this object set to the sub… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.51 | ColumnvlanCMMIPv4SubnetRoute1 | read-write | mandatory | This object sets the IPv4 address of the subnet route 1 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will always have t… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.52 | ColumnvlanCMMIPv4SubnetRouteMask1 | read-write | mandatory | This object sets the IPv4 subnet route mask 1 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will always have this object… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.53 | ColumnvlanCMMIPv4SubnetRoute2 | read-write | mandatory | This object sets the IPv4 address of the subnet route 2 for VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will always have this o… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.54 | ColumnvlanCMMIPv4SubnetRouteMask2 | read-write | mandatory | This object sets the IPv4 subnet route mask 2 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will always have this object… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.55 | ColumnvlanCMMIPv4SubnetRoute3 | read-write | mandatory | This object sets the IPv4 address of the subnet route 3 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will always have t… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.56 | ColumnvlanCMMIPv4SubnetRouteMask3 | read-write | mandatory | This object sets the IPv4 subnet route mask 3 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will always have this object… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.71 | ColumnvlanCMMIPv6Address | read-write | mandatory | This object sets the IPv6 address for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will have this object set to the IP addr… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.72 | ColumnvlanCMMIPv6AddressPrefixLen | read-write | mandatory | This object sets the IPv6 address prefix length for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will have this object set … |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.73 | ColumnvlanCMMIPv6Gateway | read-write | mandatory | This object sets the IPv6 address for the IP gateway for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will have this object… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.91 | ColumnvlanCMMIPv6SubnetRoute1 | read-write | mandatory | This object sets the IPv6 address of the subnet route 1 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will always have t… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.92 | ColumnvlanCMMIPv6SubnetRoutePrefixLen1 | read-write | mandatory | This object sets the IPv6 address prefix length of the subnet route 1 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.93 | ColumnvlanCMMIPv6SubnetRoute2 | read-write | mandatory | This object sets the IPv6 address of the subnet route 2 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will always have t… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.94 | ColumnvlanCMMIPv6SubnetRoutePrefixLen2 | read-write | mandatory | This object sets the IPv6 address prefix length of the subnet route 2 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.95 | ColumnvlanCMMIPv6SubnetRoute3 | read-write | mandatory | This object sets the IPv6 address of the subnet route 3 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will always have t… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.96 | ColumnvlanCMMIPv6SubnetRoutePrefixLen3 | read-write | mandatory | This object sets the IPv6 address prefix length of the subnet route 3 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will… |
| 1.3.6.1.4.1.2.3.51.2.4.9.1.20.21 | ScalarvlanCMMTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, vlanCMMTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3 | NodetcpProtocols | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1 | NodesnmpAgentConfig | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.1 | ScalarsnmpSystemContact | read-write | mandatory | A NULL terminated 48 byte string that contains the SNMP agent contact name. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.2 | ScalarsnmpSystemLocation | read-write | mandatory | A NULL terminated 48 byte string that contains the SNMP agent location name. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.3 | ScalarsnmpSystemAgentTrapsDisable | read-write | mandatory | Disable or enable SNMP traps. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.4 | NodesnmpAgentCommunityConfig | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.4.1 | TablesnmpCommunityTable | not-accessible | mandatory | Table of SNMP Community entries |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.4.1.1 | RowsnmpCommunityEntry | not-accessible | mandatory | SNMP community entries |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.4.1.1.1 | ColumnsnmpCommunityEntryIndex | read-only | mandatory | Index for SNMP Agent Community entry. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.4.1.1.2 | ColumnsnmpCommunityEntryCommunityName | read-write | mandatory | SNMP Community entry name. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.4.1.1.3 | ColumnsnmpCommunityEntryCommunityIpAddress1 | read-write | mandatory | SNMP Community IP address or host name. Can either be a dotted decimal IP string (e.g. 9.37.44.2) or if DNS is enabled a host name. This field also allows two … |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.4.1.1.4 | ColumnsnmpCommunityEntryCommunityIpAddress2 | read-write | mandatory | SNMP Community IP address or host name. Can either be a dotted decimal IP string (e.g. 9.37.44.2) or if DNS is enabled a host name. This field also allows two … |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.4.1.1.5 | ColumnsnmpCommunityEntryCommunityIpAddress3 | read-write | mandatory | SNMP Community IP address or host name. Can either be a dotted decimal IP string (e.g. 9.37.44.2) or if DNS is enabled a host name. This field also allows two … |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.4.1.1.6 | ColumnsnmpCommunityEntryCommunityViewType | read-write | mandatory | Access Level of the SNMPv1 managers. Note this parameter is set for each community. Therefore all three managers in the same community have the same access lev… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.5 | Scalarsnmpv1SystemAgentEnable | read-write | mandatory | Disable or enable the SNMPv1 agent. NOTE: Restart the management module if this MIB object is changed with respect to the value at system bootup time. For exam… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.6 | Scalarsnmpv3SystemAgentEnable | read-write | mandatory | Disable or enable the SNMPv3 agent. NOTE: Restart the management module if this MIB object is changed with respect to the value at system bootup time. For exam… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9 | NodesnmpAgentUserProfileConfig | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1 | TablesnmpUserProfileTable | not-accessible | mandatory | Table of SNMPv3 User Profile entries |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1.1 | RowsnmpUserProfileEntry | not-accessible | mandatory | SNMP User Profile entries |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1.1.1 | ColumnsnmpUserProfileEntryIndex | read-only | mandatory | Index for SNMPv3 Agent User Profile entry. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1.1.3 | ColumnsnmpUserProfileEntryContextName | read-write | mandatory | SNMPv3 User Profile entry - Context name for users to access MIB objects. Note that context names can be duplicates and can be shared among users. Empty contex… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1.1.4 | ColumnsnmpUserProfileEntryAuthProt | read-write | mandatory | SNMPv3 User Profile entry - Authentication Protocol supported by the user. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1.1.6 | ColumnsnmpUserProfileEntryPrivProt | read-write | mandatory | SNMPv3 User Profile entry - Privacy Protocol supported by the user. The Privacy Password must be set and the Authentication Protocol must be md5 or sha before … |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1.1.7 | ColumnsnmpUserProfileEntryPrivPassword | read-write | mandatory | SNMPv3 User Profile entry - Privacy password for the user. NOTE: Value returned for the GET command is meaningless for this MIB object for security reasons. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1.1.8 | ColumnsnmpUserProfileEntryViewType | read-write | mandatory | SNMPv3 User Profile entry - Access level (Get, Set, and Traps) of the user. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1.1.9 | ColumnsnmpUserProfileEntryIpAddress | read-write | mandatory | SNMPv3 User Profile entry - IP address or host name. Can either be a dotted decimal IP string (e.g. 9.37.44.2) or if DNS is enabled a host name. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1.1.10 | ColumnsnmpUserProfileEntryUserId | read-only | mandatory | The userid for the SNMPv3 Agent User Profile entry. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.2 | NodednsConfig | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.3.2.1 | ScalardnsEnabled | read-write | mandatory | Disable or enable the DNS agent. NOTE: To alter any of the configuration settings for the DNS agent, the following procedure should be used: (1) This object sh… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.2.2 | ScalardnsServerIPAddress1 | read-write | mandatory | Contains the primary DNS server IP address. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.2.3 | ScalardnsServerIPAddress2 | read-write | mandatory | Contains the secondary DNS server IP address. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.2.4 | ScalardnsServerIPAddress3 | read-write | mandatory | Contains the tertiary DNS server IP address. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.2.12 | ScalardnsServerIPv6Address1 | read-write | mandatory | Contains the primary IPv6 DNS server address. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.2.13 | ScalardnsServerIPv6Address2 | read-write | mandatory | Contains the secondary IPv6 DNS server address. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.2.14 | ScalardnsServerIPv6Address3 | read-write | mandatory | Contains the tertiary IPv6 DNS server address. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.2.20 | ScalardnsPriority | read-write | mandatory | Tells the order host names are resolved. The options are to either first resolve with an IPv6 DNS server or to first resolve with an IPv6 DNS server. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.3 | NodesmtpConfig | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.3.3.1 | ScalarsmtpServerNameOrIPAddress | read-write | mandatory | A NULL terminated 64 byte string that contains the SMTP server host name or IP address (a.b.c.d). |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.3.2 | ScalarattachmentsToEmailAlerts | read-write | mandatory | Indicates if the service information should be attached to an email alert. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.3.3 | ScalarsmtpEmailDomain | read-write | mandatory | A NULL terminated string that contains the SMTP email domain. If this field is empty, the MM IP address is used as the domain. However, some SMTP servers (e.g.… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4 | NodetcpApplicationConfig | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.1 | ScalartelnetInactivityTimeout | read-write | mandatory | Default is 120 seconds. Value of zero is no timeout. Max value is any positive 4 bytes value. Note that SSH also uses this timeout value to wait before disconn… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.2 | ScalarcommandModeInactivityTimeout | read-write | mandatory | The amount of time in seconds before the (Secure)TCP Command Mode times out. Default value of 0 means no timeout. Max value is any positive 4 byte value. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.3 | ScalarsecureCommandModeEnable | read-write | mandatory | Set Secure TCP Command Mode number of connections. MM will provide a max of 20 connections for both Secure TCP Command Mode and TCP Command Mode. A value of 0 … |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.4 | ScalarcommandModeEnable | read-write | mandatory | Set TCP Command Mode number of connections. MM will provide a max of 20 connections for both Secure TCP Command Mode and TCP Command Mode. A value of 0 means d… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.5 | ScalarslpAddrType | read-write | mandatory | Set SLP address type to 0 (multicast) or 1 (broadcast). Note that when slpAddrType is set to broadcast value then the multicast address set in slpMulticastAddr… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.7 | ScalarslpEnable | read-write | mandatory | Disable/Enable Service Location Protocol. NOTE: Change to Service Location Protocol will take effect after the next restart of the MM. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.9 | ScalartelnetEnable | read-write | mandatory | Disable/Enable telnet. NOTE: Change to telnet enable/disable will take effect immediately. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.10 | ScalarsshEnable | read-write | mandatory | Disable/Enable SSH. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.15 | ScalarsslServerEnable | read-write | mandatory | Disable/Enable SSL Server. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.16 | ScalarsslClientEnable | read-write | mandatory | Disable/Enable SSL Client. If no valid client or server certificate is in place, SSL client will not be allowed to set to enable. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.17 | ScalarftpEnable | read-write | mandatory | Disable/Enable FTP. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.18 | ScalarsftpEnable | read-write | mandatory | Disable/Enable SFTP. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.19 | ScalartftpEnable | read-write | mandatory | Disable/Enable TFTP. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.23 | ScalarftpTimeout | read-write | mandatory | The amount of time before FTP times out. Default is 300 seconds. Value of zero is no timeout. Max value is any positive 4 byte value. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.27 | NodemmSshServerConfig | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.27.1 | TablemmSshServerHostKeyTable | not-accessible | mandatory | A table that contains per public/private host key pair information. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.27.1.1 | RowmmSshServerHostKeyEntry | not-accessible | mandatory | A list of information about a particular public/private host key pair. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.27.1.1.1 | ColumnmmSshServerHostKeyIndex | read-only | mandatory | The index of the public/private host key pair. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.27.1.1.2 | ColumnmmSshServerHostKeyType | read-only | mandatory | The type of the public/private host key pair. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.27.1.1.3 | ColumnmmSshServerHostKeySize | read-only | mandatory | The size of the public/private host key pair. NOTE: The MM supports only the bits2048 value. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.27.1.1.4 | ColumnmmSshServerHostKeyFingerprint | read-only | mandatory | The RSA fingerprint of the public part of the host key pair. This value can be used with the SSH client to verify, on the initial connection, that the Secure S… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.27.2 | ScalarmmSshServerHostKeyGenerate | read-write | mandatory | Initiate the new Host Keys generation process for the MM SSH Server. NOTE: Value returned for the GET command is meaningless for this MIB object. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.27.3 | ScalarmmSshServerHostKeyGenerateProgress | read-only | mandatory | Indicate the progress of the key generation process. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.4.50 | ScalarcimEnable | read-write | mandatory | Disable/Enable CIM (Common Information Model) interface. NOTE: Change to CIM enable/disable will take effect immediately. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.5 | NodetcpPortAssignmentCfg | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.3.5.1 | ScalartcpPortsRestoreDefault | read-write | mandatory | Reset all ports to default value. http: 80 https: 443 telnet: 23 ssh: 22 SNMP agent: 161 SNMP trap: 162 TCP Command Mode: 6090 Secure TCP Command Mode: 6091 FT… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.5.2 | ScalarhttpPortAssignment | read-write | mandatory | HTTP port number. Default value is 80. Once changed, the URL's have to include :port at the end. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.5.3 | ScalarhttpsPortAssignment | read-write | mandatory | SSL port number. Default value is 443. Once changed, the URL's have to include :port at the end. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.5.4 | ScalartelnetPortAssignment | read-write | mandatory | Telnet port number. Default value is 23. Port change will take effect immediately. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.5.5 | ScalarsshPortAssignment | read-write | mandatory | SSH port number. Default value is 22. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.5.6 | ScalarsnmpAgentPortAssignment | read-write | mandatory | SNMP Agent port number. Default value is 161. Changes take effect after several seconds. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.5.7 | ScalarsnmpTrapsPortAssignment | read-write | mandatory | SNMP Traps port number. Default value is 162. Changes take effect after several seconds. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.5.8 | ScalarcommandModePortAssignment | read-write | mandatory | TCP Command Mode port number. Default value is 6090. Change will take effect immediately. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.5.9 | ScalarsecureCommandModePortAssignment | read-write | mandatory | Secure TCP Command Mode port number. Default value is 6091. Change will take effect immediately. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.5.13 | ScalarftpPortAssignment | read-write | mandatory | FTP port number. Default value is 21. Port change will take effect immediately. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.5.14 | ScalarftpDataPortAssignment | read-write | mandatory | FTP Data port number. Default value is 20. Port change will take effect immediately. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.5.15 | ScalartftpPortAssignment | read-write | mandatory | TFTP port number. Default value is 69. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.5.19 | ScalarslpPortAssignment | read-write | mandatory | Service Location Protocol port number. Default value is 427. NOTE: This value is normally required to be 427 to interoperate properly with other SLP enabled ap… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.5.50 | ScalarcimPortAssignment | read-write | mandatory | CIM (Common Information Model) port number. Default value is 5989. Port change will take effect immediately. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6 | NodeldapClientCfg | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.1 | ScalarldapServer1NameOrIPAddress | read-write | mandatory | A NULL terminated 255 byte string that contains the LDAP server host name or IP address (a.b.c.d). |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.2 | ScalarldapServer1PortNumber | read-write | mandatory | LDAP server port number. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.3 | ScalarldapServer2NameOrIPAddress | read-write | mandatory | A NULL terminated 255 byte string that contains the LDAP server host name or IP address (a.b.c.d). |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.4 | ScalarldapServer2PortNumber | read-write | mandatory | LDAP server port number. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.5 | ScalarldapServer3NameOrIPAddress | read-write | mandatory | A NULL terminated 255 byte string that contains the LDAP server host name or IP address (a.b.c.d). |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.6 | ScalarldapServer3PortNumber | read-write | mandatory | LDAP server port number. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.7 | ScalarldapRootDN | read-write | mandatory | A NULL terminated 255 byte string that contains the distinguished Name for root entry of directory tree. An example might look like dn=foobar,dn=com. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.9 | ScalarldapGroupFilter | read-write | mandatory | This filter is used for group authentication. It specifies what group or groups that this MM belongs to. If left blank, group authentication is disabled. Other… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.10 | ScalarldapBindingMethod | read-write | mandatory | On initial binds to the LDAP server during user authentication, there are two options: Client authentication: Bind attempt is made with client DN and password … |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.11 | ScalarldapClientAuthenticationDN | read-write | mandatory | The initial bind to the LDAP server during user authentication can be performed with anonymous authentication, client based authentication, or UPN. The client … |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.12 | ScalarldapClientAuthenticationPassword | read-write | mandatory | The client authentication password |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.13 | ScalarldapUIDsearchAttribute | read-write | mandatory | When the binding method selected is Anonymous authentication or Client authentication, the initial bind to the LDAP server is followed by a search request aime… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.14 | ScalarldapGroupSearchAttribute | read-write | mandatory | When the MM Group Filter name is configured, it is necessary to retrieve from the LDAP server the list of groups that a particular user belongs to. This is req… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.15 | ScalarldapLoginPermissionAttribute | read-write | mandatory | When a user successfully authenticates via a LDAP server, it is necessary to retrieve the login permissions for this user. In order to retrieve these permissio… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.16 | ScalarldapUseDNSOrPreConfiguredServers | read-write | mandatory | The MM contains a Version 2.0 LDAP Client that may be configured to provide user authentication through one or more LDAP servers. The LDAP server(s) to be used… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.20 | ScalarldapRBSModelCfg | read-write | mandatory | There are two mechanisms to authenticate and authorize users on the MM when using an LDAP-enabled server. The first mechanism (oldPermissionString), also known… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.21 | ScalarldapTargetName | read-write | mandatory | When administrator chooses Enhanced Role Based Security authentication model, he can associate one MM with one managed target object in Snap-in (one tool to co… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.22 | ScalarldapAuthCfg | read-write | mandatory | If ldapAuthCfg is set to 0, LDAP server is used to authenticate and authorize users. If it is set to 1, LDAP server is only used to authenticate users. Note:LD… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.23 | ScalarldapForestName | read-write | mandatory | LDAP Forest Name. Note: LDAP Forest Name is only for Active Directory environment. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.24 | ScalarldapDomainName | read-write | mandatory | A NULL terminated 255 byte string that contains the LDAP Domain Name. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.25 | ScalarldapServer4NameOrIPAddress | read-write | mandatory | A NULL terminated 255 byte string that contains the LDAP server host name or IP address (a.b.c.d). |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.6.26 | ScalarldapServer4PortNumber | read-write | mandatory | LDAP server port number. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.7 | NodeuplinkCheckConfig | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.3.7.1 | ScalaruplinkCheckEnabled | read-write | mandatory | Disable or enable network uplink checking for physical detection. NOTE: This MIB object is only applicable to systems with a standby MM. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.7.2 | ScalaruplinkCheckDelay | read-write | mandatory | Delay, in minutes (1-2880), between discovery of a failed network uplink and the subsequent MM failover for physical detection. NOTE: This MIB object is only a… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.7.3 | ScalarlogicalUplinkDestination | read-write | mandatory | Destination IP for MM to check its logical link. Specify a non-zero IP Address in order to enable logical uplink checking. NOTE: This MIB object is only applic… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.7.4 | ScalarlogicalUplinkCheckEnabled | read-write | mandatory | Disable or enable network uplink checking for logical detection. logicalUplinkDestination must be set to a non-zero IP Address before enable logical uplink che… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.7.5 | ScalarlogicalUplinkCheckDelay | read-write | mandatory | Delay, in minutes(1-2880), between discovery of a failed network uplink and the subsequent MM failover for logical detection. NOTE: This MIB object is only app… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.7.6 | ScalarphysicalUplinkCheckDelayInSecs | read-write | mandatory | Delay, in seconds(10-172800), between discovery of a failed network uplink and the subsequent MM failover for physical detection. NOTE: This MIB object is only… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.7.7 | ScalarlogicalUplinkCheckDelayInSecs | read-write | mandatory | Delay, in seconds(60-172800), between discovery of a failed network uplink and the subsequent MM failover for logical detection. NOTE: This MIB object is only … |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.7.8 | ScalarlogicalUplinkIPv6Destination | read-write | mandatory | Destination IP for MM to check its logical link using IPv6. Specify a non-zero IP Address in order to enable logical uplink checking. NOTE: This MIB object is … |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.7.9 | ScalarlogicalUplinkFailoverPolicy | read-write | mandatory | Determines when to failover if both an IPv4 and IPv6 destination have been configured. If set to 'either' the system will failover if either of the destination… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.8 | NodentpConfig | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.3.8.1 | ScalarntpEnable | read-write | mandatory | Disable/Enable the NTP client. The client will update the MM system clock at the frequency specified. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.8.2 | ScalarntpIpAddressHostname | read-write | mandatory | NTP server's IP address or hostname if DNS is enabled and configured. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.8.3 | ScalarntpUpdateFrequency | read-write | mandatory | The frequency in minutes that the NTP service runs. The value range is 0 to 45000. If the NTP update frequency is set to 0, the MM clock can only be synchroniz… |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.8.4 | ScalarntpLastUpdate | read-only | mandatory | The date and time that the NTP server last updated the system clock. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.8.5 | ScalarntpUpdateClock | read-write | mandatory | Update the MM system clock with the specified NTP server. A valid NTP server must be configured first. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.8.6 | ScalarntpAuthEntry | read-write | mandatory | The NTP v3 authentication entry to be used for time sync with a secure NTP server. The format of an authentication entry is <key index> <key type> <key>. <key … |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.8.7 | ScalarntpAuthEnable | read-write | mandatory | Enables/Disables NTP v3 authentication |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.9 | NodesyslogConfig | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.3.9.1 | ScalarsyslogSevFilterLevel | read-write | mandatory | syslogSevFilterLevel error/warning/information . |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.9.2 | NodesyslogCollectorConfig | |||
| 1.3.6.1.4.1.2.3.51.2.4.9.3.9.2.1 | TablesyslogCollectorTable | not-accessible | mandatory | Table of Syslog Collector entries |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.9.2.1.1 | RowsyslogCollectorEntry | not-accessible | mandatory | Syslog Collector entries |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.9.2.1.1.1 | ColumnsyslogCollectorIndex | read-only | mandatory | Index for Syslog Collector entry. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.9.2.1.1.2 | ColumnsyslogCollectorHostnameOrIpAddress | read-write | mandatory | Syslog Collector IP address or host name. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.9.2.1.1.3 | ColumnsyslogCollectorPort | read-write | mandatory | Syslog Collector port number. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.9.2.1.1.4 | ColumnsyslogCollectorEnable | read-write | mandatory | Syslog Collector enable/disable. |
| 1.3.6.1.4.1.2.3.51.2.4.9.3.9.3 | ScalarsyslogTestPacket | read-write | mandatory | Generate a test syslog packet. This will send a test syslog to all configured and enabled syslog collectors to assist in validating the configuration. NOTE: Va… |
| 1.3.6.1.4.1.2.3.51.2.4.10 | NodesolConfiguration | |||
| 1.3.6.1.4.1.2.3.51.2.4.10.1 | NodesolGlobalConfig | |||
| 1.3.6.1.4.1.2.3.51.2.4.10.1.1 | ScalarsolEnable | read-write | mandatory | Disable/Enable SOL dynamically. |
| 1.3.6.1.4.1.2.3.51.2.4.10.1.3 | ScalarsolAccumulateTimeout | read-write | mandatory | This value specifies how much time in millisecond SOL to buffer data before sending the next SOL packet since the last SOL packet was transmitted. Valid value … |
| 1.3.6.1.4.1.2.3.51.2.4.10.1.4 | ScalarsolCharSendThreshold | read-write | mandatory | This value specifies how many characters SOL to buffer before sending the next SOL packet since the last SOL packet was transmitted. Valid value is from 1 to 2… |
| 1.3.6.1.4.1.2.3.51.2.4.10.1.5 | ScalarsolRetry | read-write | mandatory | Retry count. Valid value from 0-7. 0 means no retries after packet is transmitted. Packet will be dropped if no ACK/NACK received by the time retries expired. |
| 1.3.6.1.4.1.2.3.51.2.4.10.1.6 | ScalarsolRetryInterval | read-write | mandatory | Retry Interval in 10 ms increment. Sets the time that the SOL will wait before the first retry and the time between retries when sending SOL packets to the rem… |
| 1.3.6.1.4.1.2.3.51.2.4.10.1.7 | ScalarsolExitToCliKeySeq | read-write | mandatory | This is the keystroke sequence used to escape out of SOL session and back to CLI console. This sequence must have at least one character. The caret symbol (^) … |
| 1.3.6.1.4.1.2.3.51.2.4.10.1.8 | ScalarsolResetBladeKeySeq | read-write | mandatory | This is the keystroke sequence used to reset the blade while in SOL session console. This sequence must have at least one character. The caret symbol (^) has a… |
| 1.3.6.1.4.1.2.3.51.2.4.10.2 | NodesolBladeConfig | |||
| 1.3.6.1.4.1.2.3.51.2.4.10.2.1 | TablesolBladeTable | not-accessible | mandatory | SOL Blade configuration table. |
| 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1 | RowsolBladeEntry | not-accessible | mandatory | SOL Blade table entry |
| 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.1 | ColumnsolBladeIndex | read-only | mandatory | SOL Blade table index. |
| 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.2 | ColumnsolBladeName | read-only | mandatory | The name of the blade as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.3 | ColumnsolBladeEnable | read-write | mandatory | Disable or enable a SOL on a blade. |
| 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.4 | ColumnsolBladeIpAddr | read-only | deprecated | This is deprecated in favor of solBladeIpAddr6. IP address of the blade derived from the IP address range for the blade system management processors on the bla… |
| 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.5 | ColumnsolBladeSessionStatus | read-only | mandatory | Status of a blade SOL session: solSessionNotReady: no SOL session connected to the blade. solSessionReady: there is an SOL session to the blade. solSessionActi… |
| 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.6 | ColumnsolBladeCapability | read-only | mandatory | Display whether or not the blade support SOL feature. |
| 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.7 | ColumnsolBladeIpAddr6 | read-only | mandatory | IPv6 address of the blade. |
| 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.8 | ColumnsolBladeRetryInterval | read-only | mandatory | Retry interval time in miliseconds. |
| 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.9 | ColumnsolBladeRetryCount | read-only | mandatory | Retry count. |
| 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.10 | ColumnsolBladeBytesSent | read-only | mandatory | Number of bytes sent. |
| 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.11 | ColumnsolBladeBytesReceived | read-only | mandatory | Number of bytes received. |
| 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.12 | ColumnsolBladeDestinationMAC | read-only | mandatory | MAC address of the blade. |
| 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.13 | ColumnsolBladeConsoleUserId | read-only | mandatory | Sol console user name. |
| 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.14 | ColumnsolBladeConsoleLoginFrom | read-only | mandatory | The location information from where the SOL console is logged in. |
| 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.15 | ColumnsolBladeConsoleLoginStart | read-only | mandatory | The time that SOL console starts. |
| 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.16 | ColumnsolBladeConsoleLoginEnd | read-only | mandatory | The time that SOL console ends. |
| 1.3.6.1.4.1.2.3.51.2.4.11 | NodechassisInternalNetwork | |||
| 1.3.6.1.4.1.2.3.51.2.4.11.1 | ScalarcinsSupported | read-only | mandatory | Number of Chassis Internal Network (CIN) definitions supported. Currently a maximum of 14 CIN definitions can be supported. |
| 1.3.6.1.4.1.2.3.51.2.4.11.2 | ScalarcinGlobalEnable | read-write | mandatory | Disable/Enable Chassis Internal Network (CIN) function dynamically. Enabled: MM reads the CIN entries. For each enabled entry, - If the CIN VLAN ID is new and … |
| 1.3.6.1.4.1.2.3.51.2.4.11.3 | TablecinTable | not-accessible | mandatory | Chassis Internal Network (CIN) configuration table. |
| 1.3.6.1.4.1.2.3.51.2.4.11.3.1 | RowcinEntry | not-accessible | mandatory | Chassis Internal Network (CIN) table entry. |
| 1.3.6.1.4.1.2.3.51.2.4.11.3.1.1 | ColumncinIndex | read-only | mandatory | Chassis Internal Network (CIN) table index. |
| 1.3.6.1.4.1.2.3.51.2.4.11.3.1.2 | ColumncinDefExists | read-only | mandatory | Indicates if a Chassis Internal Network (CIN) definition exists for this index or not. |
| 1.3.6.1.4.1.2.3.51.2.4.11.3.1.3 | ColumncinDelete | read-write | mandatory | Delete Chassis Internal Network (CIN) definition. Works like CIN entry disabled. However, the entry is also deleted. NOTE: Value returned for the GET command i… |
| 1.3.6.1.4.1.2.3.51.2.4.11.3.1.4 | ColumncinEnable | read-write | mandatory | Disable or enable a Chassis Internal Network (CIN) definition. Enabled: MM reads the entry and creates a new CIN interface if the CIN VLAN ID is new and does n… |
| 1.3.6.1.4.1.2.3.51.2.4.11.3.1.5 | ColumncinId | read-write | mandatory | This is the Chassis Internal Network (CIN) Virtual LAN (VLAN) ID for the internal management network between the Management Module, I/O Module, and the blade O… |
| 1.3.6.1.4.1.2.3.51.2.4.11.3.1.6 | ColumncinIpAddress | read-write | mandatory | Chassis Internal Network (CIN) IP address. Restrictions: - CIN entries cannot have matching IP addresses, with the exception of 0.0.0.0. - Multiple IP addresse… |
| 1.3.6.1.4.1.2.3.51.2.4.11.3.1.7 | ColumncinIpv6Address | read-write | mandatory | Chassis Internal Network (CIN) IPv6 address NOTE: When ipv4 is enable on one interface,this column will display all zero IPv6 address. |
| 1.3.6.1.4.1.2.3.51.2.4.11.4 | NodecinStatus | |||
| 1.3.6.1.4.1.2.3.51.2.4.11.4.1 | TablecinStatusTable | not-accessible | mandatory | Table of Chassis Internal Network (CIN) status entry information. |
| 1.3.6.1.4.1.2.3.51.2.4.11.4.1.1 | RowcinStatusEntry | not-accessible | mandatory | Chassis Internal Network (CIN) status table entry. |
| 1.3.6.1.4.1.2.3.51.2.4.11.4.1.1.1 | ColumncinStatusIndex | read-only | mandatory | The Chassis Internal Network (CIN) status log index number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.4.11.4.1.1.2 | ColumncinStatusString | read-only | mandatory | Status of a Chassis Internal Network (CIN) connection. For example: Index:1 VLANID:4094 IPADDR:192.168.70.100 MAC:01:0A:0B:00:01:01 Type:Learned Status:Operati… |
| 1.3.6.1.4.1.2.3.51.2.7 | NoderestartReset | |||
| 1.3.6.1.4.1.2.3.51.2.7.4 | ScalarrestartSPImmediately | read-write | mandatory | Restart the MM immediately. NOTE: Value returned for the GET command is meaningless for this MIB object. |
| 1.3.6.1.4.1.2.3.51.2.7.5 | ScalarrestartStandbyMM | read-write | mandatory | Restarts the Standby MM from the Primary MM. NOTE: Value returned for the GET command is meaningless for this MIB object. NOTE: This mib object is only applica… |
| 1.3.6.1.4.1.2.3.51.2.7.7 | ScalarswitchOverRedundantMM | read-write | mandatory | Switch over to the redundant Management Module. The failover will not occur if the standby or primary MM is in flashing mode. NOTE: Value returned for the GET … |
| 1.3.6.1.4.1.2.3.51.2.7.20 | ScalarresetSPConfigAndRestart | read-write | mandatory | Will cause all the MM information to be reset to it's initial factory defaults (all previous configuration information is lost) and the MM will be re-started. … |
| 1.3.6.1.4.1.2.3.51.2.7.21 | ScalarresetSPConfigAndRestartSaveLogs | read-write | mandatory | Will cause all the MM information to be reset to it's initial factory defaults (all previous configuration information is lost) and the MM will be re-started. … |
| 1.3.6.1.4.1.2.3.51.2.22 | Nodecomponents | |||
| 1.3.6.1.4.1.2.3.51.2.22.1 | NodeprocessorBlade | |||
| 1.3.6.1.4.1.2.3.51.2.22.1.4 | NodebladePolicyControl | |||
| 1.3.6.1.4.1.2.3.51.2.22.1.4.1 | TablebladePolicyControlTable | not-accessible | mandatory | Table of blade power policy control information. Contains power on/off enablement status for each blade. |
| 1.3.6.1.4.1.2.3.51.2.22.1.4.1.1 | RowbladePolicyControlEntry | not-accessible | mandatory | Power policy control entry |
| 1.3.6.1.4.1.2.3.51.2.22.1.4.1.1.1 | ColumnpolicyControlIndex | read-only | mandatory | Blade power policy control index. |
| 1.3.6.1.4.1.2.3.51.2.22.1.4.1.1.2 | ColumnpolicyControlBladeId | read-only | mandatory | The numeric blade ID. |
| 1.3.6.1.4.1.2.3.51.2.22.1.4.1.1.3 | ColumnpolicyControlBladeExists | read-only | mandatory | Indicates whether the server blade specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.22.1.4.1.1.4 | ColumnpolicyControlBladePowerState | read-only | mandatory | The power state for blade. 0 = off, 1 = on, 3 = standby, 4 = hibernate, 255 = unknown. |
| 1.3.6.1.4.1.2.3.51.2.22.1.4.1.1.5 | ColumnpolicyControlBladeHealthState | read-only | mandatory | The system health state for the blade. Unknown: Blade is in an undefined state. Good: Blade is operating normally. Warning: One or more outstanding warnings ex… |
| 1.3.6.1.4.1.2.3.51.2.22.1.4.1.1.6 | ColumnpolicyControlBladeName | read-only | mandatory | The name of the blade as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.1.4.1.1.7 | ColumnpolicyLocalPowerControlEnable | read-write | mandatory | Blade local power policy control enablement status. |
| 1.3.6.1.4.1.2.3.51.2.22.1.4.1.1.10 | ColumnpolicyWakeOnLanControlEnable | read-write | mandatory | Blade Wake On LAN enablement status. If WOL is not supported by the blade, it displays 'notApplicable' and WOL can not be enabled or disabled. |
| 1.3.6.1.4.1.2.3.51.2.22.1.4.2 | NodebladePolicy | |||
| 1.3.6.1.4.1.2.3.51.2.22.1.4.2.1 | ScalarbladePolicyLocalPowerControlEnable | read-write | mandatory | Blade local power control enablement status policy. |
| 1.3.6.1.4.1.2.3.51.2.22.1.4.2.4 | ScalarbladePolicyWakeOnLanControlEnable | read-write | mandatory | Blade Wake On LAN enablement status policy. The notApplicable(255) enumeration is not valid for SET operations. NOTE: Value returned for the GET command is mea… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5 | NodebladeMonitors | |||
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1 | TablebladeSystemStatusTable | not-accessible | mandatory | Table of blade status information. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1 | RowbladeSystemStatusEntry | not-accessible | mandatory | Blade system status entry |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.1 | ColumnbladeStatusIndex | read-only | mandatory | Blade system status index. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.2 | ColumnbladeId | read-only | mandatory | The numeric blade ID. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.3 | ColumnbladeExists | read-only | mandatory | Indicates whether the server blade specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.4 | ColumnbladePowerState | read-only | mandatory | Indicates the power state of the blade specified. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.5 | ColumnbladeHealthState | read-only | mandatory | The system health state for the blade. Unknown: Blade is in an undefined state. Good: Blade is operating normally. Warning: One or more outstanding warnings ex… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.6 | ColumnbladeName | read-only | mandatory | The name of the blade as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.7 | ColumnbladeRemotePowerEnable | read-only | mandatory | Remote power state for the blade. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.10 | ColumnbladeConnectionType | read-only | mandatory | Connection type of the expansion card number one. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.13 | ColumnbladeRemoteWakeOnLanEnable | read-only | mandatory | Remote wake on LAN state for the blade. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.14 | ColumnbladeServerExpansion | read-only | mandatory | This shows whether this blade has an expansion board attached. A yes column indicates that an expansion board is installed for this blade. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.15 | ColumnbladeWidth | read-only | mandatory | The width of the blade including any supplement blade attached to it |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.17 | ColumnbladeServerExpansion2 | read-only | mandatory | This shows whether this blade has an expansion board attached. A yes column indicates that an expansion board is installed for this blade. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.22 | ColumnbladeConnectionType2 | read-only | mandatory | Connection type of the expansion card number 2. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.23 | ColumnbladeConnectionType3 | read-only | mandatory | Connection type of the expansion card number 3. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.24 | ColumnbladeConnectionType4 | read-only | mandatory | Connection type of the expansion card number 4. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.25 | ColumnbladeConnectionType5 | read-only | mandatory | Connection type of the expansion card number 5. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.41 | ColumnbladeHighSpeedConnectionType | read-only | mandatory | Connection type of the high speed expansion card number 1. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.51 | ColumnbladeIOCompatibility | read-only | mandatory | I/O compatibility status for the blade. The possible values and their meanings are as follows: unknown: This indicates a communication error for the blade. ok:… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.52 | ColumnbladeInventoryReady | read-only | mandatory | When a blade management controller or the MM is reset, the blade inventory data is refreshed in the MM database. This includes items like IBM VPD (e.g. - seria… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.2 | TablebladeHealthSummaryTable | not-accessible | mandatory | Table of blade health summary information. Contains information about the overall blade health status. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.2.1 | RowbladeHealthSummaryEntry | not-accessible | mandatory | Blade health summary entry |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.2.1.1 | ColumnbladeHealthSummaryIndex | read-only | mandatory | Blade health summary index. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.2.1.2 | ColumnbladeHealthSummaryBladeId | read-only | mandatory | The numeric blade ID. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.2.1.3 | ColumnbladeHealthSummarySeverity | read-only | mandatory | System health summary severity. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.2.1.4 | ColumnbladeHealthSummaryDescription | read-only | mandatory | System health summary description. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.2.1.5 | ColumnbladeHealthSummaryDateTime | read-only | mandatory | System health summary date time. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.2.1.6 | ColumnbladeHealthSummaryEventID | read-only | mandatory | System health summary event ID. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3 | TablebladeTemperaturesTable | not-accessible | mandatory | Table of blade temperatures information. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1 | RowbladeTemperaturesEntry | not-accessible | mandatory | Blade temperatures table entry |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.1 | ColumntemperatureIndex | read-only | mandatory | Blade temperatures table index. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.2 | ColumntemperatureBladeId | read-only | mandatory | The numeric blade ID. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.3 | ColumntemperatureBladeExists | read-only | mandatory | Indicates whether the server blade specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.4 | ColumntemperatureBladePowerState | read-only | mandatory | Indicates the power state of the blade specified. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.5 | ColumntemperatureBladeName | read-only | mandatory | The name of the blade as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.6 | ColumntemperatureCPU1 | read-only | mandatory | The blade CPU temperature in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for negative or blank space for… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.7 | ColumntemperatureCPU2 | read-only | mandatory | The blade CPU temperature in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for negative or blank space for… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.8 | ColumntemperatureCPU3 | read-only | mandatory | The blade CPU temperature in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for negative or blank space for… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.9 | ColumntemperatureCPU4 | read-only | mandatory | The blade CPU temperature in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for negative or blank space for… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.10 | ColumntemperatureDASD1 | read-only | mandatory | The blade DASD temperature in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for negative or blank space fo… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.11 | ColumnbladeSensorTempCapability | read-only | mandatory | Indicates whether the server blade is IPMI capable or not. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.12 | ColumnbladeSensor1Temp | read-only | mandatory | Temperature reading for an IPMI blade expressed in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for negat… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.13 | ColumnbladeSensor2Temp | read-only | mandatory | Temperature reading for an IPMI blade expressed in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for negat… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.14 | ColumnbladeSensor3Temp | read-only | mandatory | Temperature reading for an IPMI blade expressed in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for negat… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.15 | ColumnbladeSensor4Temp | read-only | mandatory | Temperature reading for an IPMI blade expressed in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for negat… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.16 | ColumnbladeSensor5Temp | read-only | mandatory | Temperature reading for an IPMI blade expressed in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for negat… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.17 | ColumnbladeSensor6Temp | read-only | mandatory | Temperature reading for an IPMI blade expressed in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for negat… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.18 | ColumnbladeSensor7Temp | read-only | mandatory | Temperature reading for an IPMI blade expressed in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for negat… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.19 | ColumnbladeSensor8Temp | read-only | mandatory | Temperature reading for an IPMI blade expressed in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for negat… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.20 | ColumnbladeSensor9Temp | read-only | mandatory | Temperature reading for an IPMI blade expressed in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for negat… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4 | TablebladeTemperatureThresholdsTable | not-accessible | mandatory | Table of blade temperature thresholds information. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1 | RowbladeTemperatureThresholdsEntry | not-accessible | mandatory | Blade temperature thresholds table entry |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.1 | ColumntemperatureThresholdIndex | read-only | mandatory | Blade temperature threshold table index. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.2 | ColumntemperatureThresholdBladeId | read-only | mandatory | The numeric blade ID. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.3 | ColumntemperatureThresholdBladeExists | read-only | mandatory | Indicates whether the server blade specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.4 | ColumntemperatureThresholdBladePowerState | read-only | mandatory | Indicates the power state of the blade specified. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.5 | ColumntemperatureThresholdBladeName | read-only | mandatory | The name of the blade as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.6 | ColumntemperatureCPU1HardShutdown | read-only | mandatory | The blade CPU hard shutdown temperature in degrees centigrade(C). If the component's temperature rises above this value the system will be powered off immediat… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.7 | ColumntemperatureCPU1Warning | read-only | mandatory | The blade CPU warning temperature in degrees centigrade(C). If the temperature rises above this value a warning alert/event if enabled will be generated. An oc… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.8 | ColumntemperatureCPU1WarningReset | read-only | mandatory | The blade CPU warning reset temperature in degrees centigrade(C). If the temperature rises above this value and if a warning alert/event had previously been cr… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.9 | ColumntemperatureCPU2HardShutdown | read-only | mandatory | The blade CPU hard shutdown temperature in degrees centigrade(C). If the component's temperature rises above this value the system will be powered off immediat… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.10 | ColumntemperatureCPU2Warning | read-only | mandatory | The blade CPU warning temperature in degrees centigrade(C). If the temperature rises above this value a warning alert/event if enabled will be generated. An oc… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.11 | ColumntemperatureCPU2WarningReset | read-only | mandatory | The blade CPU warning reset temperature in degrees centigrade(C). If the temperature rises above this value and if a warning alert/event had previously been cr… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.12 | ColumntemperatureCPU3HardShutdown | read-only | mandatory | The blade CPU hard shutdown temperature in degrees centigrade(C). If the component's temperature rises above this value the system will be powered off immediat… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.13 | ColumntemperatureCPU3Warning | read-only | mandatory | The blade CPU warning temperature in degrees centigrade(C). If the temperature rises above this value a warning alert/event if enabled will be generated. An oc… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.14 | ColumntemperatureCPU3WarningReset | read-only | mandatory | The blade CPU warning reset temperature in degrees centigrade(C). If the temperature rises above this value and if a warning alert/event had previously been cr… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.15 | ColumntemperatureCPU4HardShutdown | read-only | mandatory | The blade CPU hard shutdown temperature in degrees centigrade(C). If the component's temperature rises above this value the system will be powered off immediat… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.16 | ColumntemperatureCPU4Warning | read-only | mandatory | The blade CPU warning temperature in degrees centigrade(C). If the temperature rises above this value a warning alert/event if enabled will be generated. An oc… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.17 | ColumntemperatureCPU4WarningReset | read-only | mandatory | The blade CPU warning reset temperature in degrees centigrade(C). If the temperature rises above this value and if a warning alert/event had previously been cr… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.18 | ColumntemperatureDASD1HardShutdown | read-only | mandatory | The blade DASD hard shutdown temperature in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for negative or … |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.19 | ColumntemperatureDASD1Warning | read-only | mandatory | The blade DASD warning temperature in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for negative or blank … |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.20 | ColumntemperatureDASD1WarningReset | read-only | mandatory | The blade DASD warning reset temperature in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for negative or … |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.21 | ColumnbladeTempThresholdSensorCapability | read-only | mandatory | Indicates whether the server blade is IPMI capable or not. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.22 | ColumntemperatureSensor1HardShutdown | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.23 | ColumntemperatureSensor1Warning | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.24 | ColumntemperatureSensor1WarningReset | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.25 | ColumntemperatureSensor2HardShutdown | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.26 | ColumntemperatureSensor2Warning | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.27 | ColumntemperatureSensor2WarningReset | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.28 | ColumntemperatureSensor3HardShutdown | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.29 | ColumntemperatureSensor3Warning | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.30 | ColumntemperatureSensor3WarningReset | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.31 | ColumntemperatureSensor4HardShutdown | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.32 | ColumntemperatureSensor4Warning | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.33 | ColumntemperatureSensor4WarningReset | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.34 | ColumntemperatureSensor5HardShutdown | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.35 | ColumntemperatureSensor5Warning | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.36 | ColumntemperatureSensor5WarningReset | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.37 | ColumntemperatureSensor6HardShutdown | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.38 | ColumntemperatureSensor6Warning | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.39 | ColumntemperatureSensor6WarningReset | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.40 | ColumntemperatureSensor7HardShutdown | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.41 | ColumntemperatureSensor7Warning | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.42 | ColumntemperatureSensor7WarningReset | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.43 | ColumntemperatureSensor8HardShutdown | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.44 | ColumntemperatureSensor8Warning | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.45 | ColumntemperatureSensor8WarningReset | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.46 | ColumntemperatureSensor9HardShutdown | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.47 | ColumntemperatureSensor9Warning | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.48 | ColumntemperatureSensor9WarningReset | read-only | mandatory | The blade hard shutdown temperature for IPMI blades in degrees centigrade(C). An octet string expressed as 'sddd.dd Centigrade' where: s is the sign ('-' for n… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5 | TablebladeVoltagesTable | not-accessible | mandatory | Table of blade voltages information. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1 | RowbladeVoltagesEntry | not-accessible | mandatory | Blade voltages table entry |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.1 | ColumnvoltageIndex | read-only | mandatory | Blade voltages table index. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.2 | ColumnvoltageBladeId | read-only | mandatory | The numeric blade ID. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.3 | ColumnvoltageBladeExists | read-only | mandatory | Indicates whether the server blade specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.4 | ColumnvoltageBladePowerState | read-only | mandatory | Indicates the power state of the blade specified. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.5 | ColumnvoltageBladeName | read-only | mandatory | The name of the blade as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.6 | ColumnbladePlus5Volt | read-only | mandatory | +5 Volt power supply voltage reading for the blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.7 | ColumnbladePlus3pt3Volt | read-only | mandatory | +3.3 Volt power supply voltage reading for the blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative … |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.8 | ColumnbladePlus12Volt | read-only | mandatory | +12 Volt power supply voltage reading for the blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative o… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.10 | ColumnbladePlus2pt5Volt | read-only | mandatory | +2.5 Volt power supply voltage reading for the blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative … |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.11 | ColumnbladePlus1pt5Volt | read-only | mandatory | +1.5 Volt power supply voltage reading for the blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative … |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.12 | ColumnbladePlus1pt25Volt | read-only | mandatory | +1.25 Volt power supply voltage reading for the blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.13 | ColumnbladeVRM1Volt | read-only | mandatory | VRM 1 voltage reading for the blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positi… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.14 | ColumnbladeSensorVoltCapability | read-only | mandatory | Indicates whether the server blade is IPMI capable or not. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.15 | ColumnbladeSensor1Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.16 | ColumnbladeSensor2Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.17 | ColumnbladeSensor3Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.18 | ColumnbladeSensor4Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.19 | ColumnbladeSensor5Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.20 | ColumnbladeSensor6Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.21 | ColumnbladeSensor7Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.22 | ColumnbladeSensor8Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.23 | ColumnbladeSensor9Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.24 | ColumnbladeSensor10Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.25 | ColumnbladeSensor11Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.26 | ColumnbladeSensor12Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.27 | ColumnbladeSensor13Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.28 | ColumnbladeSensor14Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.29 | ColumnbladeSensor15Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.30 | ColumnbladeSensor16Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.31 | ColumnbladeSensor17Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.32 | ColumnbladeSensor18Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.33 | ColumnbladeSensor19Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.34 | ColumnbladeSensor20Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.35 | ColumnbladeSensor21Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.36 | ColumnbladeSensor22Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.37 | ColumnbladeSensor23Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.38 | ColumnbladeSensor24Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.39 | ColumnbladeSensor25Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.40 | ColumnbladeSensor26Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.41 | ColumnbladeSensor27Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.42 | ColumnbladeSensor28Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.43 | ColumnbladeSensor29Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.44 | ColumnbladeSensor30Volt | read-only | mandatory | Voltage reading for an IPMI blade expressed in Volts(V). An octet string expressed as 'sdd.dd Volts' where: s is the sign ('-' for negative or '+' for positive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6 | TablebladeVoltageThresholdsTable | not-accessible | mandatory | Table of blade VoltageThresholds information. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1 | RowbladeVoltageThresholdsEntry | not-accessible | mandatory | Blade voltage thresholds table entry |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.1 | ColumnvoltageThresholdIndex | read-only | mandatory | Blade voltage thresholds table index. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.2 | ColumnvoltageThresholdBladeId | read-only | mandatory | The numeric blade ID. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.3 | ColumnvoltageThresholdBladeExists | read-only | mandatory | Indicates whether the server blade specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.4 | ColumnvoltageThresholdBladePowerState | read-only | mandatory | Indicates the power state of the blade specified. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.5 | ColumnvoltageThresholdBladeName | read-write | mandatory | The name of the blade as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.6 | ColumnbladePlus5VoltHighWarning | read-only | mandatory | Voltage warning threshold reading expressed in Volts(V). If the voltage rises above this value a warning alert/event if enabled will be generated. An octet str… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.7 | ColumnbladePlus5VoltLowWarning | read-only | mandatory | Voltage warning threshold reading expressed in Volts(V). If the voltage drops below this value a warning alert/event if enabled will be generated. An octet str… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.8 | ColumnbladePlus3pt3VoltHighWarning | read-only | mandatory | Voltage warning threshold reading expressed in Volts(V). If the voltage rises above this value a warning alert/event if enabled will be generated. An octet str… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.9 | ColumnbladePlus3pt3VoltLowWarning | read-only | mandatory | Voltage warning threshold reading expressed in Volts(V). If the voltage drops below this value a warning alert/event if enabled will be generated. An octet str… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.10 | ColumnbladePlus12VoltHighWarning | read-only | mandatory | Voltage warning threshold reading expressed in Volts(V). If the voltage rises above this value a warning alert/event if enabled will be generated. An octet str… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.11 | ColumnbladePlus12VoltLowWarning | read-only | mandatory | Voltage warning threshold reading expressed in Volts(V). If the voltage drops below this value a warning alert/event if enabled will be generated. An octet str… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.14 | ColumnbladePlus2pt5VoltHighWarning | read-only | mandatory | Voltage warning threshold reading expressed in Volts(V). If the voltage rises above this value a warning alert/event if enabled will be generated. An octet str… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.15 | ColumnbladePlus2pt5VoltLowWarning | read-only | mandatory | Voltage warning threshold reading expressed in Volts(V). If the voltage drops below this value a warning alert/event if enabled will be generated. An octet str… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.16 | ColumnbladePlus1pt5VoltHighWarning | read-only | mandatory | Voltage warning threshold reading expressed in Volts(V). If the voltage rises above this value a warning alert/event if enabled will be generated. An octet str… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.17 | ColumnbladePlus1pt5VoltLowWarning | read-only | mandatory | Voltage warning threshold reading expressed in Volts(V). If the voltage drops below this value a warning alert/event if enabled will be generated. An octet str… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.18 | ColumnbladePlus1pt25VoltHighWarning | read-only | mandatory | Voltage warning threshold reading expressed in Volts(V). If the voltage rises above this value a warning alert/event if enabled will be generated. An octet str… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.19 | ColumnbladePlus1pt25VoltLowWarning | read-only | mandatory | Voltage warning threshold reading expressed in Volts(V). If the voltage drops below this value a warning alert/event if enabled will be generated. An octet str… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.22 | ColumnbladeVoltThresholdSensorCapability | read-only | mandatory | Indicates whether the server blade is IPMI capable or not. |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.23 | ColumnbladeSensor1VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.24 | ColumnbladeSensor1VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.25 | ColumnbladeSensor2VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.26 | ColumnbladeSensor2VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.27 | ColumnbladeSensor3VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.28 | ColumnbladeSensor3VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.29 | ColumnbladeSensor4VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.30 | ColumnbladeSensor4VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.31 | ColumnbladeSensor5VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.32 | ColumnbladeSensor5VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.33 | ColumnbladeSensor6VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.34 | ColumnbladeSensor6VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.35 | ColumnbladeSensor7VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.36 | ColumnbladeSensor7VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.37 | ColumnbladeSensor8VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.38 | ColumnbladeSensor8VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.39 | ColumnbladeSensor9VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.40 | ColumnbladeSensor9VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.41 | ColumnbladeSensor10VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.42 | ColumnbladeSensor10VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.43 | ColumnbladeSensor11VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.44 | ColumnbladeSensor11VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.45 | ColumnbladeSensor12VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.46 | ColumnbladeSensor12VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.47 | ColumnbladeSensor13VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.48 | ColumnbladeSensor13VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.49 | ColumnbladeSensor14VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.50 | ColumnbladeSensor14VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.51 | ColumnbladeSensor15VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.52 | ColumnbladeSensor15VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.53 | ColumnbladeSensor16VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.54 | ColumnbladeSensor16VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.55 | ColumnbladeSensor17VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.56 | ColumnbladeSensor17VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.57 | ColumnbladeSensor18VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.58 | ColumnbladeSensor18VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.59 | ColumnbladeSensor19VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.60 | ColumnbladeSensor19VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.61 | ColumnbladeSensor20VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.62 | ColumnbladeSensor20VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.63 | ColumnbladeSensor21VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.64 | ColumnbladeSensor21VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.65 | ColumnbladeSensor22VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.66 | ColumnbladeSensor22VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.67 | ColumnbladeSensor23VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.68 | ColumnbladeSensor23VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.69 | ColumnbladeSensor24VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.70 | ColumnbladeSensor24VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.71 | ColumnbladeSensor25VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.72 | ColumnbladeSensor25VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.73 | ColumnbladeSensor26VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.74 | ColumnbladeSensor26VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.75 | ColumnbladeSensor27VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.76 | ColumnbladeSensor27VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.77 | ColumnbladeSensor28VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.78 | ColumnbladeSensor28VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.79 | ColumnbladeSensor29VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.80 | ColumnbladeSensor29VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.81 | ColumnbladeSensor30VoltHighWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage rises above this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.82 | ColumnbladeSensor30VoltLowWarning | read-only | mandatory | Voltage warning threshold reading for IPMI blades expressed in Volts(V). If the voltage drops below this value, a critical alert/event if enabled will be gener… |
| 1.3.6.1.4.1.2.3.51.2.22.1.6 | NodebladePowerRestart | |||
| 1.3.6.1.4.1.2.3.51.2.22.1.6.1 | TablebladePowerRestartTable | not-accessible | mandatory | Table of blade remote power control information. Contains power on/off enablement status for each blade. |
| 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1 | RowbladePowerRestartEntry | not-accessible | mandatory | Blade power restart table entry |
| 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.1 | ColumnpowerRestartIndex | read-only | mandatory | Blade power restart table index. |
| 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.2 | ColumnpowerRestartBladeId | read-only | mandatory | The numeric blade ID. |
| 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.3 | ColumnpowerRestartBladeExists | read-only | mandatory | Indicates whether the server blade specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.4 | ColumnpowerRestartBladePowerState | read-only | mandatory | Indicates the power state of the blade specified. If the state cannot be determined, the unknown(255) is returned. |
| 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.5 | ColumnpowerRestartBladeHealthState | read-only | mandatory | The system health state for the blade. Unknown: Blade is in an undefined state. Good: Blade is operating normally. Warning: One or more outstanding warnings ex… |
| 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.6 | ColumnpowerRestartBladeName | read-only | mandatory | The name of the blade as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.7 | ColumnpowerOnOffBlade | read-write | mandatory | Control the power state of a specific blade. Off: Power Off Blade. On: Power On Blade. Softoff: Shut Down OS and Power Off Blade. This operation is not support… |
| 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.8 | ColumnrestartBlade | read-write | mandatory | Restart a blade. NOTE: Value returned for the GET command is meaningless for this MIB object. |
| 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.9 | ColumnrestartBladeSMP | read-write | mandatory | Restart a blade's system management processor. NOTE: Value returned for the GET command is meaningless for this MIB object. |
| 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.10 | ColumnrestartBladeNMI | read-write | mandatory | Issue an NMI to the blade. This option is not supported on all blades. NOTE: Value returned for the GET command is meaningless for this MIB object. |
| 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.11 | ColumnrestartBladeClearNVRAM | read-write | mandatory | Restart a blade and set NVRAM to default values. This option is not supported on all blades. NOTE: Value returned for the GET command is meaningless for this M… |
| 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.12 | ColumnrestartBladeInvokeDiags | read-write | mandatory | Restart a blade and boot into diagnostic mode. This option is not supported on all blades. NOTE: Value returned for the GET command is meaningless for this MIB… |
| 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.13 | ColumnrestartBladeInvokeDiagsFromDefaultBootList | read-write | mandatory | Restart a blade and boot into diagnostic mode from Default Boot List as defined on the blade. This option is not supported on all blades. NOTE: Value returned … |
| 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.14 | ColumnrestartBladeToSMSBootMenu | read-write | deprecated | Restart a blade to SMS boot menu. This option is not supported on all blades, and at the time of this MIB definition was only supported on POWER blades. This o… |
| 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.15 | ColumnbladePowerEnableSMSBootMenu | read-write | mandatory | Enables/disables a blade restart to the SMS boot menu. Setting this object to 'enable(1)' will cause a reboot of the node to the SMS menu. This option is not s… |
| 1.3.6.1.4.1.2.3.51.2.22.1.7 | NodebladeConfiguration | |||
| 1.3.6.1.4.1.2.3.51.2.22.1.7.1 | TablebladeConfigurationTable | not-accessible | mandatory | Table of blade configuration information. Contains boot mode and auto power on/off settings for each blade. |
| 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1 | RowbladeConfigurationEntry | not-accessible | mandatory | Blade configuration table entry |
| 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1.1 | ColumnconfigurationIndex | read-only | mandatory | Blade configuration table index. |
| 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1.2 | ColumnconfigurationBladeId | read-only | mandatory | The numeric blade ID. |
| 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1.3 | ColumnconfigurationBladeExists | read-only | mandatory | Indicates whether the server blade specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1.4 | ColumnconfigurationBladePowerState | read-only | mandatory | Indicates the power state of the blade specified. |
| 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1.5 | ColumnconfigurationBladeName | read-write | mandatory | The name of the blade as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1.7 | ColumnconfigurationBladeActiveBootMode | read-only | mandatory | Indicates the active copy of the firmware from which the blade is booting. NOTE: Some blades do not support the automatic boot recovery. It displays 'notApplic… |
| 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1.8 | ColumnconfigurationBladePendingBootMode | read-write | mandatory | Indicates the copy of the firmware from which the blade will boot after the next reboot. NOTE: Some blades do not support the automatic boot recovery. It displ… |
| 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1.9 | ColumnconfigurationBladeAutoPowerOn | read-write | mandatory | Blade auto-power on policy. - restore: blade will be powered on which were previously on. - auto: blade will automatically be powered on when power is applied … |
| 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1.10 | ColumnconfigurationBladePowerOnRestartDelay | read-write | mandatory | Restart delay (in seconds) when power is applied to a blade. |
| 1.3.6.1.4.1.2.3.51.2.22.1.7.2 | NodebladePowerManagementPolicy | |||
| 1.3.6.1.4.1.2.3.51.2.22.1.7.2.1 | ScalarpowerManagementPolicy | read-write | mandatory | Power Module Redundancy Intended for a single power source into the chassis where each Power Module is on its own dedicated circuit. Maximum power is limited t… |
| 1.3.6.1.4.1.2.3.51.2.22.1.7.2.3 | ScalaracousticMode | read-write | mandatory | Acoustic mode setting for thermal conditions. A setting of disabled (0), disables this feature. A setting of acoustic-quiet-level1 (5) is the least restrictive… |
| 1.3.6.1.4.1.2.3.51.2.22.1.10 | NodebladeBootCountPowerOnTime | |||
| 1.3.6.1.4.1.2.3.51.2.22.1.10.1 | TablebladeBootCountPowerOnTimeTable | not-accessible | mandatory | Table per blade of the number of boots for the blade and the number of seconds the blade has been powered on. |
| 1.3.6.1.4.1.2.3.51.2.22.1.10.1.1 | RowbladeBootCountPowerOnTimeEntry | not-accessible | mandatory | The number of boots for the blade and the number of seconds the blade has been powered on. |
| 1.3.6.1.4.1.2.3.51.2.22.1.10.1.1.1 | ColumnbootCountPowerOnTimeBladeIndex | read-only | mandatory | Blade boot count/Power On Time table index. |
| 1.3.6.1.4.1.2.3.51.2.22.1.10.1.1.2 | ColumnbootCountPowerOnTimeBladeId | read-only | mandatory | The numeric blade ID. |
| 1.3.6.1.4.1.2.3.51.2.22.1.10.1.1.3 | ColumnbootCountPowerOnTimeBoots | read-write | mandatory | Blade Boot Count. If there is no blade in the given slot then this value is undefined. Writing this value resets the Boot Count to zero. |
| 1.3.6.1.4.1.2.3.51.2.22.1.10.1.1.4 | ColumnbootCountPowerOnTimeSecs | read-write | mandatory | Blade Power On Time in seconds. If there is no blade in the given slot then this value is undefined. Writing this value resets the Power On Time to zero. |
| 1.3.6.1.4.1.2.3.51.2.22.1.11 | ScalarbladeVlanId | read-write | mandatory | This is the virtual LAN ID for the internal management network between the MM and the blade system management processors (BSMPs). The range of valid VLAN ID's … |
| 1.3.6.1.4.1.2.3.51.2.22.1.12 | NodebladeNetworkConfiguration | |||
| 1.3.6.1.4.1.2.3.51.2.22.1.12.5 | TablebladeIPv4ConfigTable | not-accessible | mandatory | Table of all blades' network interfaces. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1 | RowbladeIPv4ConfigEntry | not-accessible | mandatory | Blade configuration table entry |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.1 | ColumnbladeIPv4ConfigIndex | read-only | mandatory | The blade's slot number. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.2 | ColumnbladeIPv4ConfigPortIndex | read-only | mandatory | The physical port number of the given entry. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.3 | ColumnbladeIPv4ConfigPortLabel | read-only | mandatory | Show string label that identifies the interface. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.4 | ColumnbladeIPv4ConfigPhysicalLinkStatus | read-only | mandatory | Indicates whether this network interface port is up or down. If this network interface doesn't support up/down, show 'notApplicable(255)'. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.5 | ColumnbladeIPv4ConfigPhysicalLinkState | read-write | mandatory | Configuration object for requesting the physical port to be either, down(0), up(1) or loopback(2). To get the current status of a physical port, use the object… |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.6 | ColumnbladeIPv4ConfigIPAddr | read-write | mandatory | Show/modify current IP address of the blade network interface. Note that only if the bladeIPv4ConfigPhysicalLinkStatus is 'up(1)' and the bladeIPv4ConfigDHCPEn… |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.7 | ColumnbladeIPv4ConfigSubnetMask | read-write | mandatory | Show or modifie current subnet mask of the blade network interface. Note that only if the bladeIPv4ConfigPhysicalLinkStatus is 'up(1)' and the bladeIPv4ConfigD… |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.8 | ColumnbladeIPv4ConfigGatewayAddr | read-write | mandatory | Show or modify current IP gateway of the blade network interface. Note that only if the bladeIPv4ConfigPhysicalLinkStatus is 'up(1)' and the bladeIPv4ConfigDHC… |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.9 | ColumnbladeIPv4ConfigVlanId | read-write | mandatory | This is the Virtual LAN ID for supported network interface cards (NICs). The range of valid VLAN ID's is 0 to 4095. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.10 | ColumnbladeIPv4ConfigDHCPEnable | read-write | mandatory | IP config method on the blade network interface to modify mode to static IP, DHCP and 'try DHCP then try static'. If this network interface doesn't support DHC… |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.11 | ColumnbladeIPv4ConfigMACAddr | read-only | mandatory | Show the blade network interface MAC address. If this network interface doesn't support MAC, show 'notApplicable'. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.10 | NodebladeIPv6Config | |||
| 1.3.6.1.4.1.2.3.51.2.22.1.12.10.1 | TablebladeIPv6ConfigTable | not-accessible | mandatory | A table of IPv6 configuration options for blades. NOTE: This MIB object is not applicable to blades that do not support IPv6. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.10.1.1 | RowbladeIPv6ConfigEntry | not-accessible | mandatory | IPv6 configuration options for a blade. NOTE: This MIB object is not applicable to blades that do not support IPv6. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.10.1.1.1 | ColumnbladeIPv6ConfigIndex | read-only | mandatory | The blade's slot number |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.10.1.1.2 | ColumnbladeIPv6ConfigPortIndex | read-only | mandatory | The physical port number of the given entry |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.10.1.1.3 | ColumnbladeIPv6ConfigEnabled | read-write | mandatory | Enables/Disables IPv6 support on the blade. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.10.1.1.4 | ColumnbladeIPv6ConfigStatic | read-write | mandatory | Enables/Disables IPv6 static configuration support on the blade. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.10.1.1.5 | ColumnbladeDHCPv6ConfigEnabled | read-write | mandatory | Enables/Disables DHCPv6 address configuration support on the blade. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.10.1.1.6 | ColumnbladeIPv6ConfigStatelessEnabled | read-write | mandatory | Enables/Disables IPv6 stateless auto-configuration support on the blade. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.10.2 | TablebladeIPv6AddressTable | not-accessible | mandatory | A table of assigned IPv6 addresses for blades. NOTE: This MIB object is not applicable to blades that do not support IPv6. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.10.2.1 | RowbladeIPv6AddressEntry | not-accessible | mandatory | The assigned IPv6 address for a given blade. NOTE: This MIB object is not applicable to blades that do not support IPv6. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.10.2.1.1 | ColumnbladeIPv6AddressIndex | read-only | mandatory | The blade's slot number. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.10.2.1.2 | ColumnbladeIPv6AddressPortIndex | read-only | mandatory | The blade's physical port number for the given entry. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.10.2.1.3 | ColumnbladeIPv6AddressEntryIndex | read-only | mandatory | The blade's address entry index. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.10.2.1.4 | ColumnbladeIPv6AddressType | read-only | mandatory | The address type. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.10.2.1.5 | ColumnbladeIPv6Address | read-write | mandatory | The assigned IPv6 address. Note: 'write' is for static ipv6 only. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.10.2.1.6 | ColumnbladeIPv6AddressPrefixLen | read-write | mandatory | The prefix length for the given address. Note: 'write' is for static ipv6 only. |
| 1.3.6.1.4.1.2.3.51.2.22.1.12.10.2.1.7 | ColumnbladeIPv6AddressDefaultRoute | read-write | mandatory | The default route used for the given address. Note: 'write' is for static ipv6 only. |
| 1.3.6.1.4.1.2.3.51.2.22.1.13 | TablebladeBayDataTable | not-accessible | mandatory | Table of blade bay data (BBD) information. |
| 1.3.6.1.4.1.2.3.51.2.22.1.13.1 | RowbladeBayDataEntry | not-accessible | mandatory | Blade bay data (BBD) table entry. |
| 1.3.6.1.4.1.2.3.51.2.22.1.13.1.1 | ColumnbayDataIndex | read-only | mandatory | Blade bay data (BBD) table index. |
| 1.3.6.1.4.1.2.3.51.2.22.1.13.1.2 | ColumnbayDataBladeId | read-only | mandatory | The numeric blade ID. |
| 1.3.6.1.4.1.2.3.51.2.22.1.13.1.3 | ColumnbayDataBladeExists | read-only | mandatory | Indicates whether the server blade specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.22.1.13.1.4 | ColumnbayDataBladePowerState | read-only | mandatory | Indicates the power state of the blade specified. |
| 1.3.6.1.4.1.2.3.51.2.22.1.13.1.5 | ColumnbayDataBladeName | read-only | mandatory | The name of the blade as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.1.13.1.6 | ColumnbayData | read-write | mandatory | A null terminated string that defines the Blade Bay Data (BBD). This data is pushed to the blade's BSMP and SMBIOS structures, where it can used by the blade's… |
| 1.3.6.1.4.1.2.3.51.2.22.1.13.1.7 | ColumnbayDataBladeStatus | read-only | mandatory | This shows Blade Bay Data (BBD) status. 0 means the blade fully supports BBD; 1 means that the blade's BIOS does not support BBD; 2 means that there is no blad… |
| 1.3.6.1.4.1.2.3.51.2.22.1.14 | NodebladeSPEthOverUSBInterface | |||
| 1.3.6.1.4.1.2.3.51.2.22.1.14.1 | TablespEthOverUSBInterfaceTable | not-accessible | mandatory | Table of blade Service Processor's Ethernet over USB interface. |
| 1.3.6.1.4.1.2.3.51.2.22.1.14.1.1 | RowspEthOverUSBInterfaceEntry | not-accessible | mandatory | Blade Service Processor's Ethernet over USB interface entry. |
| 1.3.6.1.4.1.2.3.51.2.22.1.14.1.1.1 | ColumnspEthOverUSBInterfaceIndex | read-only | mandatory | Service Processor's Ethernet over USB interface table index. |
| 1.3.6.1.4.1.2.3.51.2.22.1.14.1.1.2 | ColumnspEthOverUSBInterfaceBladeId | read-only | mandatory | The numeric blade ID. |
| 1.3.6.1.4.1.2.3.51.2.22.1.14.1.1.3 | ColumnspEthOverUSBInterfaceBladeExists | read-only | mandatory | Indicates whether the blade specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.22.1.14.1.1.6 | ColumnspEthOverUSBInterfaceBladeName | read-only | mandatory | The name of the blade as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.1.14.1.1.9 | ColumnspEthOverUSBInterfaceEnable | read-write | mandatory | This object allows the user to view the status of, and enable or disable, a blade Service Processor's command interface on Ethernet-over-USB. NOTE: If the blad… |
| 1.3.6.1.4.1.2.3.51.2.22.1.15 | TablebootDeviceInfoTable | not-accessible | mandatory | Table of blade boot device information. Contains info for the boot devices for each blade. |
| 1.3.6.1.4.1.2.3.51.2.22.1.15.1 | RowbootDeviceInfoEntry | not-accessible | mandatory | Boot device entry |
| 1.3.6.1.4.1.2.3.51.2.22.1.15.1.1 | ColumnbootInfoTopologyIndex | read-only | mandatory | The unique identifier for a node containing boot devices in this table. The chassis and each installed component is represented by a hardware topology tree, wh… |
| 1.3.6.1.4.1.2.3.51.2.22.1.15.1.2 | ColumnbootDeviceIndex | read-only | mandatory | An index for the boot device for the given topology id. |
| 1.3.6.1.4.1.2.3.51.2.22.1.15.1.3 | ColumnbootDeviceId | read-only | mandatory | The device Id of the boot device. |
| 1.3.6.1.4.1.2.3.51.2.22.1.15.1.4 | ColumnbootDeviceActive | read-only | mandatory | Specifies whether the boot device is active. |
| 1.3.6.1.4.1.2.3.51.2.22.1.15.1.5 | ColumnbootDevicePresence | read-only | mandatory | Specifies whether the boot device is present. |
| 1.3.6.1.4.1.2.3.51.2.22.1.15.1.6 | ColumnbootDeviceLabel | read-only | mandatory | The device label of the boot device. |
| 1.3.6.1.4.1.2.3.51.2.22.1.15.1.7 | ColumnbootDeviceUserLabel | read-only | mandatory | The user label of the boot device. |
| 1.3.6.1.4.1.2.3.51.2.22.1.15.1.8 | ColumnbootDeviceOrder | read-only | mandatory | The sequence number in boot order of the boot device. 0 specifies this device is not in the boot sequence. |
| 1.3.6.1.4.1.2.3.51.2.22.1.16 | TablebootSequenceInfoTable | not-accessible | mandatory | Table of blade boot sequence information. Contains the boot sequence information for each blade. |
| 1.3.6.1.4.1.2.3.51.2.22.1.16.1 | RowbootSequenceInfoEntry | not-accessible | mandatory | Boot sequence entry |
| 1.3.6.1.4.1.2.3.51.2.22.1.16.1.1 | ColumnbootSequenceInfoTopologyIndex | read-only | mandatory | The unique identifier for a row in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree… |
| 1.3.6.1.4.1.2.3.51.2.22.1.16.1.2 | ColumnbootSequenceInfoMaxBootDevices | read-only | mandatory | The maximum number of boot devices. |
| 1.3.6.1.4.1.2.3.51.2.22.1.16.1.3 | ColumnbootSequenceInfoBootSequence | read-write | mandatory | A blank delimited string of device ids in the order of the boot sequence. For example, 00000001 00000002 00000005. Note that the boot sequence list can change … |
| 1.3.6.1.4.1.2.3.51.2.22.3 | NodeswitchModule | |||
| 1.3.6.1.4.1.2.3.51.2.22.3.1 | NodeswitchModuleControl | |||
| 1.3.6.1.4.1.2.3.51.2.22.3.1.1 | TablesmControlTable | not-accessible | mandatory | Switch module control table. |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1 | RowsmControlEntry | not-accessible | mandatory | Switch module control table entry |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.1 | ColumnsmControlIndex | read-only | mandatory | Switch module control table index. |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.2 | ColumnswitchModuleControlId | read-only | mandatory | The switch module numeric identifier. |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.3 | ColumnsmPostResultsAvailable | read-only | mandatory | Describes whether the switch module POST diagnostic result value contained in the smPostResultsValue is valid. |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.4 | ColumnsmPostResultsValue | read-only | mandatory | The range of values and meanings are as follows: 0x00 - 0x7F ( 0 - 127) Base internal functions 0x80 - 0x9F (128 - 159) Internal interface failures 0xA0 - 0xAF… |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.5 | ColumnswitchModuleMemDiagEnableDisable | read-write | deprecated | Switch module memory diagnostics enabled or disabled. NOTE: The numeric values for the enumerations for enabled and disabled are non-traditional (i.e. - 0 and … |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.6 | ColumnsmCfgCtrlEnableDisable | read-write | mandatory | Switch module configuration control. When set to enabled, only the MM can manage the module. This MIB object can not be set, if MM grants switch module the Pro… |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.7 | ColumnsmExtEthPortsEnableDisable | read-write | mandatory | Switch module non-management ethernet ports enabled or disabled. This MIB object can not be set, if MM grants switch module the Protected Mode permission. This… |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.9 | ColumnsmCfgCtrlOnResetEnableDisable | read-write | mandatory | Switch module configuration control on resets (default and unsolicited). When set to enabled, the factory default IP configuration will become active when the … |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.15 | ColumnsmHealthState | read-only | mandatory | The health state for the switch module. 0 = unknown, 1 = good, 2 = warning, 3 = bad. |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.16 | ColumnsmPMState | read-only | mandatory | The Protected Mode Status for the switch module. standby- Protected Mode capability exists on the IOM but has not been activated on the switch module or the MM… |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.17 | ColumnsmPMCtrlEnableDisable | read-write | mandatory | MM Protected Mode permission for the switch module. disabled - allow MM to disable Protected Mode Permission for the switch module. enabled - allow MM to grant… |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.18 | ColumnsmIOCompatibility | read-only | mandatory | The compatibility status for the I/O module. The possible values and their meanings are as follows: Unknown: This indicates a communication error for the I/O m… |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.2 | TablesmPingTable | not-accessible | mandatory | Allows pinging one of the active assigned addresses of an I/O module. NOTE: This table is not applicable to modules that are running in Stacking Mode and IP co… |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.2.1 | RowsmPingEntry | not-accessible | mandatory | Represents a single address that can be pinged |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.2.1.1 | ColumnsmPingIndex | read-only | mandatory | The switch module's slot number |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.2.1.2 | ColumnsmPingAddressEntryIndex | read-only | mandatory | The switch module's address entry index |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.2.1.3 | ColumnsmPingAddress | read-only | mandatory | The switch module's IPv4 or IPv6 address |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.2.1.4 | ColumnsmPingAddressExecute | read-write | mandatory | Pings the given IP address. NOTE: The GET operation for this object is meaningless. |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.7 | TablesmPowerRestartTable | not-accessible | mandatory | Switch module power restart table. |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1 | RowsmPowerRestartEntry | not-accessible | mandatory | Switch module power restart table entry |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.1 | ColumnsmPowerRestartIndex | read-only | mandatory | Switch module power restart index. |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.2 | ColumnsmPowerRestartId | read-only | mandatory | The switch module numeric identifier. |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.3 | ColumnsmSwitchExists | read-only | mandatory | Indicates whether the switch module specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.5 | ColumnsmMACAddress | read-only | mandatory | Switch module MAC address. For IOMs which are members of a stack, this field is not applicable and should be disregarded. |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.6 | ColumnsmIPAddress | read-only | mandatory | The switch module current IP address. If the switch module is participating in the Stacking Mode and IP Configuration is protected, then the stack management I… |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.7 | ColumnswitchModulePowerOnOff | read-write | mandatory | I/O Module power on or power off. If powering on a currently powered off I/O Module, then the I/O Module will execute a POST. The results of this POST will nee… |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.8 | ColumnsmReset | read-write | mandatory | For the case where the switch module is currently powered on, this command will effectively power off and then power on the switch module indicated and cause i… |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.9 | ColumnsmResetToDefault | read-write | mandatory | For the case where the switch module is currently powered on, this command will effectively power off and then power on the switch module indicated and cause i… |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.10 | ColumnsmRestartAndRunStdDiag | read-write | mandatory | To power cycle the selected module(s) and then run the standard diagnostic test package. NOTE: Value returned for the GET command is meaningless for this MIB o… |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.11 | ColumnsmRestartAndRunExtDiag | read-write | mandatory | To power cycle the selected module(s) and then run the extended diagnostic test package. This option is not supported on all I/O modules. NOTE: Value returned … |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.12 | ColumnsmRestartAndRunFullDiag | read-write | mandatory | To power cycle the selected module(s) and then run the full diagnostic test package. The full diagnostic test package may take over 5 minutes to run. This opti… |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.15 | ColumnsmPowerOnRestartDelay | read-write | mandatory | Restart delay (in seconds) when power is applied to a switch module. |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.21 | ColumnsmSwitchWidth | read-only | mandatory | Switch module width. |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.22 | ColumnsmManufacturingID | read-only | mandatory | Switch module hardware VPD manufacturing ID. |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.23 | ColumnsmStackingModeState | read-only | mandatory | The Stacking Mode Status for the switch module. standby - I/O module has stacking capability but is not part of a stack. member - I/O module has stacking capab… |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.24 | ColumnsmStackingModeInfo | read-only | mandatory | A string containing a text description about the details of which functions are protected for a switch module when it is in Stacking Mode as Master or Member. … |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.10 | TablesmIOCompatibilityTable | not-accessible | mandatory | Switch module control table. |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.10.1 | RowsmIOCompatibilityEntry | not-accessible | mandatory | Switch module IO compatibility table entry |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.10.1.1 | ColumnsmIOCompatibilityIndex | read-only | mandatory | Switch module IO compatibility index. |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.10.1.2 | ColumnsmIOCompatibilityId | read-only | mandatory | The switch module numeric identifier. |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.10.1.3 | ColumnsmIOCompatibilityModuleBay | read-only | mandatory | The modules (identified by an id string) that this I/O module can communicate with over the midplane networking fabric (i.e. a physical path exists between the… |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.10.1.4 | ColumnsmIOCompatibilityModulePower | read-only | mandatory | The power state of the module specified in smIOCompatibilityModuleBay. |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.10.1.5 | ColumnsmIOCompatibilityModuleFabricType | read-only | mandatory | The I/O fabric type on the module side for the module. 'n/a' will be displayed if the corresponding channel is not populated on the module side (e.g. we are lo… |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.10.1.6 | ColumnsmIOCompatibilityStatus | read-only | mandatory | The compatibility status for this I/O module and the module specified in smIOCompatibilityModuleBay. The possible values are: OK: No compatibility issues n/a: … |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.10.1.7 | ColumnsmIOCompatibilityTargetTopologyPath | read-only | mandatory | The unique identifier for a component which communicates with this IO module. This is the same component identified with an id string in the smIOCompatibilityM… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2 | NodeswitchModuleConfig | |||
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1 | NodeswitchMgmtNetworkCfg | |||
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1 | NodeswitchCurrentNwCfg | |||
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1 | TablesmCurrentIPInfoTable | not-accessible | mandatory | Switch module current IP information. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1.1 | RowsmCurrentIPInfoEntry | not-accessible | mandatory | Switch module current IP table entry. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1.1.1 | ColumnsmCurrentIPInfoIndex | read-only | mandatory | Switch module current IP info index. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1.1.2 | ColumnsmCurrentIPInfoId | read-only | mandatory | The switch module numeric identifier. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1.1.3 | ColumnsmCurrentIPInfoExists | read-only | mandatory | Indicates whether the switch module specified exists or not. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP config… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1.1.4 | ColumnsmCurrentIPInfoPowerState | read-only | mandatory | Indicates whether the I/O Module specified is powered on or not. The value 'shutdownInProgress' is for the I/O Module that may take some time to transition fro… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1.1.6 | ColumnsmCurrentIPAddr | read-only | mandatory | The switch module current IP address. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1.1.7 | ColumnsmCurrentSubnetMask | read-only | mandatory | The switch module current subnet mask. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1.1.8 | ColumnsmCurrentGateway | read-only | mandatory | The switch module current IP gateway. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1.1.9 | ColumnsmCurrentIPConfigMethod | read-only | mandatory | The switch module current IP configuration method. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2 | NodeswitchNewNwCfg | |||
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1 | TablesmNewIPInfoTable | not-accessible | mandatory | Switch module new IP information. NOTE: This MIB object is not applicable to modules that are running in Network Address Translation (NAT) Mode or Stacking Mod… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1 | RowsmNewIPInfoEntry | not-accessible | mandatory | Switch module new IP configuration information table entry. NOTE: This MIB table is not applicable to modules that are running in Network Address Translation (… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1.1 | ColumnsmNewIPInfoIndex | read-only | mandatory | Switch module new IP info index. NOTE: This MIB object is not applicable to modules that are running in Network Address Translation (NAT) Mode or Stacking Mode… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1.2 | ColumnsmNewIPInfoId | read-only | mandatory | The switch module numeric identifier. NOTE: This MIB object is not applicable to modules that are running in Network Address Translation (NAT) Mode or Stacking… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1.3 | ColumnsmNewIPInfoExists | read-only | mandatory | Indicates whether the switch module specified exists or not. NOTE: This MIB object is not applicable to modules that are running in Network Address Translation… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1.4 | ColumnsmNewIPInfoPowerState | read-only | mandatory | Indicates whether the switch module specified is powered on or not. NOTE: This MIB object is not applicable to modules that are running in Network Address Tran… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1.6 | ColumnsmNewIPAddr | read-write | mandatory | The switch module new IP address. Before setting this object to a new value, smNewIpconfigEnableDisable object must first be set to disabled. NOTE: This MIB ob… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1.7 | ColumnsmNewSubnetMask | read-write | mandatory | The switch module new subnet mask. Before setting this object to a new value, smNewIpconfigEnableDisable object must first be set to disabled. NOTE: This MIB o… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1.8 | ColumnsmNewGateway | read-write | mandatory | The switch module new IP gateway. Before setting this object to a new value, smNewIpconfigEnableDisable object must first be set to disabled. NOTE: This MIB ob… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1.9 | ColumnsmNewIPConfigMethod | read-write | mandatory | The switch module new IP configuration method. Before setting this object to a new value, smNewIpconfigEnableDisable object must first be set to disabled. NOTE… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1.10 | ColumnsmNewIPConfigEnableDisable | read-write | mandatory | A set command enables a new IP configuration that has been previously defined. A get command indicates whether the new IP configuration information has been en… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4 | NodeswitchIPv6Config | |||
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.1 | TablesmIPv6ConfigTable | not-accessible | mandatory | A table of IPv6 configuration options for switch modules. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configura… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.1.1 | RowsmIPv6ConfigEntry | not-accessible | mandatory | IPv6 configuration options for a switch module.. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is p… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.1.1.1 | ColumnsmIPv6ConfigIndex | read-only | mandatory | The switch module's slot number |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.1.1.2 | ColumnsmIPv6ConfigEnabled | read-write | mandatory | Enables/Disables IPv6 support on the switch module. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.1.1.3 | ColumnsmIPv6ConfigStatic | read-write | mandatory | Enables/Disables IPv6 static configuration support on the switch module. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.1.1.4 | ColumnsmDHCPv6ConfigEnabled | read-write | mandatory | Enables/Disables DHCPv6 address configuration support on the switch module. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.1.1.5 | ColumnsmIPv6ConfigStatelessEnabled | read-write | mandatory | Enables/Disables IPv6 stateless auto-configuration support on the switch module. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.2 | TablesmIPv6AddressTable | not-accessible | mandatory | A table of assigned IPv6 addresses for switch modules. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuratio… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.2.1 | RowsmIPv6AddressEntry | not-accessible | mandatory | The assigned IPv6 address for a given switch module NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration i… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.2.1.1 | ColumnsmIPv6AddressIndex | read-only | mandatory | The switch module's slot number |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.2.1.2 | ColumnsmIPv6AddressEntryIndex | read-only | mandatory | The switch module's address entry index |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.2.1.3 | ColumnsmIPv6AddressType | read-only | mandatory | The address type. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.2.1.4 | ColumnsmIPv6Address | read-only | mandatory | The assigned IPv6 address |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.2.1.5 | ColumnsmIPv6AddressPrefixLen | read-only | mandatory | The prefix length for the given address. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.2.1.6 | ColumnsmIPv6AddressDefaultRoute | read-only | mandatory | The default route used for the given address |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.3 | TablesmIPv6StaticConfigTable | not-accessible | mandatory | Allows configuration of static IPv6 information for supported IO modules. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode … |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.3.1 | RowsmIPv6StaticConfigEntry | not-accessible | mandatory | The static IP address assignment information for an IO module. Once the assignement has taken place the address will show up as a row in the smIPv6AddressTable… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.3.1.1 | ColumnsmIPv6StaticIndex | read-only | mandatory | The switch module's slot number |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.3.1.2 | ColumnsmIPv6StaticAddress | read-write | mandatory | The assigned IPv6 address. NOTE: If changing with smIPv6StaticAddressPrefixLen and/or smIPv6StaticAddressDefaultRoute sending the update as a single SET comman… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.3.1.3 | ColumnsmIPv6StaticAddressPrefixLen | read-write | mandatory | The prefix length for the given address. NOTE: If changing with smIPv6StaticAddress and/or smIPv6StaticAddressDefaultRoute sending the update as a single SET c… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.3.1.4 | ColumnsmIPv6StaticAddressDefaultRoute | read-write | mandatory | The default route used for the given address NOTE: If changing with smIPv6StaticAddressPrefixLen and/or smIPv6StaticAddress sending the update as a single SET … |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2 | NodeswitchPortCfg | |||
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1 | NodeswitchModOnePortCfg | |||
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1 | TablesmOnePortCfgTable | not-accessible | mandatory | Switch Module 1 port configuration information. NOTE: This option is not supported on all I/O modules. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1 | RowsmOnePortCfgEntry | not-accessible | mandatory | Switch Module 1 port configuration information table entry |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.1 | ColumnsmOnePortCfgIndex | read-only | mandatory | Switch Module 1 port sequence index. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.2 | ColumnsmOnePortCfgLabel | read-only | mandatory | Switch Module 1 port label |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.3 | ColumnsmOnePortCfgType | read-only | mandatory | Switch Module 1 port type: External port: This port is connected to external device and is for data traffic. External management port: This port is solely for … |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.4 | ColumnsmOnePortCfgLinkSetting | read-write | mandatory | Current port link setting for Switch Module 1. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.5 | ColumnsmOnePortCfgLinkState | read-only | mandatory | Current port link state of Switch Module 1. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.6 | ColumnsmOnePortCfgSpeedSetting | read-write | mandatory | Set the port speed using the data rate and duplex value. For examples: 100mh: 100 Mbps in Half Duplex; 10gf: 10 Gbps in Full Duplex; auto: The working speed of… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.7 | ColumnsmOnePortCfgSpeedStatus | read-only | mandatory | Current port speed of Switch Module 1. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.8 | ColumnsmOnePortCfgAvailSpeeds | read-only | mandatory | Available speed setting per port for Switch Module 1. If there is more than one setting, the speeds are separated by a comma and then a space. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.9 | ColumnsmOnePortCfgMedia | read-only | mandatory | Port media type of Switch Module 1. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.10 | ColumnsmOnePortCfgProtocol | read-only | mandatory | Port protocol of Switch Module 1. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.11 | ColumnsmOnePortCfgWidth | read-only | mandatory | The width of the port in terms of how many combined cables are present for Switch Module 1. A value of 0 indicates this field is not applicable to the switch p… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.12 | ColumnsmOnePortCfgCableLength | read-only | mandatory | The length (in meters) of the cable supported by this port for Switch Module 1. A value of 0 indicates this field is not applicable to the switch ports. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.13 | ColumnsmOnePortCfgCableType | read-only | mandatory | External cable type for this port, for example, active copper or passive fiber. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.14 | ColumnsmOnePortCfgVendorName | read-only | mandatory | The cable manufacturer. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.15 | ColumnsmOnePortCfgCompatibility | read-only | mandatory | Compatibility of the external cable that is plugged into the port. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.16 | ColumnsmOnePortCfgDataRate | read-only | mandatory | Data rate supported for this port. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2 | NodeswitchModTwoPortCfg | |||
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1 | TablesmTwoPortCfgTable | not-accessible | mandatory | Switch Module 2 port configuration information. Note: This option is not supported on all I/O modules. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1 | RowsmTwoPortCfgEntry | not-accessible | mandatory | Switch Module 2 port configuration information table entry |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.1 | ColumnsmTwoPortCfgIndex | read-only | mandatory | Switch Module 2 port sequence index. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.2 | ColumnsmTwoPortCfgLabel | read-only | mandatory | Switch Module 2 port label |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.3 | ColumnsmTwoPortCfgType | read-only | mandatory | Switch Module 2 port type: External port: This port is connected to external device and is for data traffic. External management port: This port is solely for … |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.4 | ColumnsmTwoPortCfgLinkSetting | read-write | mandatory | Current port link setting for Switch Module 2. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.5 | ColumnsmTwoPortCfgLinkState | read-only | mandatory | Current port link state of Switch Module 2. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.6 | ColumnsmTwoPortCfgSpeedSetting | read-write | mandatory | Set the port speed using the data rate and duplex value. For examples: 100mf: 100Mbps in Half Duplex; 10gf: 10 Gbps in Full Duplex; auto: The working speed of … |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.7 | ColumnsmTwoPortCfgSpeedStatus | read-only | mandatory | Current port speed of Switch Module 2. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.8 | ColumnsmTwoPortCfgAvailSpeeds | read-only | mandatory | Available speed setting per port for Switch Module 2. If there is more than one setting, the speeds are separated by a comma and then a space. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.9 | ColumnsmTwoPortCfgMedia | read-only | mandatory | Port media type of Switch Module 2. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.10 | ColumnsmTwoPortCfgProtocol | read-only | mandatory | Port protocol of Switch Module 2. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.11 | ColumnsmTwoPortCfgWidth | read-only | mandatory | The width of the port in terms of how many combined cables are present for Switch Module 2. A value of 0 indicates this field is not applicable to the switch p… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.12 | ColumnsmTwoPortCfgCableLength | read-only | mandatory | The length (in meters) of the cable supported by this port for Switch Module 2. A value of 0 indicates this field is not applicable to the switch ports. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.13 | ColumnsmTwoPortCfgCableType | read-only | mandatory | External cable type for this port, for example, active copper or passive fiber. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.14 | ColumnsmTwoPortCfgVendorName | read-only | mandatory | The cable manufacturer. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.15 | ColumnsmTwoPortCfgCompatibility | read-only | mandatory | Compatibility of the external cable that is plugged into the port. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.16 | ColumnsmTwoPortCfgDataRate | read-only | mandatory | Data rate supported for this port. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3 | NodeswitchModThreePortCfg | |||
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1 | TablesmThreePortCfgTable | not-accessible | mandatory | Switch Module 3 port configuration information. Note: This option is not supported on all I/O modules. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1 | RowsmThreePortCfgEntry | not-accessible | mandatory | Switch Module 3 port configuration information table entry |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.1 | ColumnsmThreePortCfgIndex | read-only | mandatory | Switch Module 3 port sequence index. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.2 | ColumnsmThreePortCfgLabel | read-only | mandatory | Switch Module 3 port label |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.3 | ColumnsmThreePortCfgType | read-only | mandatory | Switch Module 3 port type: External port: This port is connected to external device and is for data traffic. External management port: This port is solely for … |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.4 | ColumnsmThreePortCfgLinkSetting | read-write | mandatory | Current port link setting for Switch Module 3. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.5 | ColumnsmThreePortCfgLinkState | read-only | mandatory | Current port link state of Switch Module 3. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.6 | ColumnsmThreePortCfgSpeedSetting | read-write | mandatory | Set the port speed using the data rate and duplex value. For examples: 100mf: 100Mbps in Half Duplex; 10gf: 10 Gbps in Full Duplex; auto: The working speed of … |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.7 | ColumnsmThreePortCfgSpeedStatus | read-only | mandatory | Current port speed of Switch Module 3. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.8 | ColumnsmThreePortCfgAvailSpeeds | read-only | mandatory | Available speed setting per port for Switch Module 3. If there is more than one setting, the speeds are separated by a comma and then a space. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.9 | ColumnsmThreePortCfgMedia | read-only | mandatory | Port media type of Switch Module 3. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.10 | ColumnsmThreePortCfgProtocol | read-only | mandatory | Port protocol of Switch Module 3. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.11 | ColumnsmThreePortCfgWidth | read-only | mandatory | The width of the port in terms of how many combined cables are present for Switch Module 3. A value of 0 indicates this field is not applicable to the switch p… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.12 | ColumnsmThreePortCfgCableLength | read-only | mandatory | The length (in meters) of the cable supported by this port for Switch Module 3. A value of 0 indicates this field is not applicable to the switch ports. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.13 | ColumnsmThreePortCfgCableType | read-only | mandatory | External cable type for this port, for example, active copper or passive fiber. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.14 | ColumnsmThreePortCfgVendorName | read-only | mandatory | The cable manufacturer. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.15 | ColumnsmThreePortCfgCompatibility | read-only | mandatory | Compatibility of the external cable that is plugged into the port. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.16 | ColumnsmThreePortCfgDataRate | read-only | mandatory | Data rate supported for this port. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4 | NodeswitchModFourPortCfg | |||
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1 | TablesmFourPortCfgTable | not-accessible | mandatory | Switch Module 4 port configuration information. Note: This option is not supported on all I/O modules. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1 | RowsmFourPortCfgEntry | not-accessible | mandatory | Switch Module 4 port configuration information table entry |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.1 | ColumnsmFourPortCfgIndex | read-only | mandatory | Switch Module 4 port sequence index. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.2 | ColumnsmFourPortCfgLabel | read-only | mandatory | Switch Module 4 port label |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.3 | ColumnsmFourPortCfgType | read-only | mandatory | Switch Module 4 port type: External port: This port is connected to external device and is for data traffic. External management port: This port is solely for … |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.4 | ColumnsmFourPortCfgLinkSetting | read-write | mandatory | Current port link setting for Switch Module 4. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.5 | ColumnsmFourPortCfgLinkState | read-only | mandatory | Current port link state of Switch Module 4. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.6 | ColumnsmFourPortCfgSpeedSetting | read-write | mandatory | Set the port speed using the data rate and duplex value. For examples: 100mf: 100Mbps in Half Duplex; 10gf: 10 Gbps in Full Duplex; auto: The working speed of … |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.7 | ColumnsmFourPortCfgSpeedStatus | read-only | mandatory | Current port speed of Switch Module 4. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.8 | ColumnsmFourPortCfgAvailSpeeds | read-only | mandatory | Available speed setting per port for Switch Module 4. If there is more than one setting, the speeds are separated by a comma and then a space. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.9 | ColumnsmFourPortCfgMedia | read-only | mandatory | Port media type of Switch Module 4. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.10 | ColumnsmFourPortCfgProtocol | read-only | mandatory | Port protocol of Switch Module 4. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.11 | ColumnsmFourPortCfgWidth | read-only | mandatory | The width of the port in terms of how many combined cables are present for Switch Module 4. A value of 0 indicates this field is not applicable to the switch p… |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.12 | ColumnsmFourPortCfgCableLength | read-only | mandatory | The length (in meters) of the cable supported by this port for Switch Module 4. A value of 0 indicates this field is not applicable to the switch ports. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.13 | ColumnsmFourPortCfgCableType | read-only | mandatory | External cable type for this port, for example, active copper or passive fiber. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.14 | ColumnsmFourPortCfgVendorName | read-only | mandatory | The cable manufacturer. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.15 | ColumnsmFourPortCfgCompatibility | read-only | mandatory | Compatibility of the external cable that is plugged into the port. |
| 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.16 | ColumnsmFourPortCfgDataRate | read-only | mandatory | Data rate supported for this port. |
| 1.3.6.1.4.1.2.3.51.2.22.4 | NodechassisTopology | |||
| 1.3.6.1.4.1.2.3.51.2.22.4.1 | ScalarchassisResponseVersion | read-only | mandatory | Chassis response version. |
| 1.3.6.1.4.1.2.3.51.2.22.4.2 | ScalarchassisFlags | read-only | mandatory | Chassis flags. 1 = a server blade chassis, 0 = a rack or standalone chassis. |
| 1.3.6.1.4.1.2.3.51.2.22.4.18 | ScalarchassisNoOfFPsSupported | read-only | deprecated | This object is deprecated because the power modules' fan packs are integrated into the power modules and are not removable as on previous power modules. Number… |
| 1.3.6.1.4.1.2.3.51.2.22.4.19 | ScalarchassisNoOfBayDevicesSupported | read-only | mandatory | Maximum number of bays found in the chassis. |
| 1.3.6.1.4.1.2.3.51.2.22.4.20 | ScalarchassisNoOfSMsSupported | read-only | mandatory | Number of switch modules (SMs) supported. |
| 1.3.6.1.4.1.2.3.51.2.22.4.21 | ScalarchassisNoOfMMsSupported | read-only | mandatory | Number of management modules (MMs) supported. |
| 1.3.6.1.4.1.2.3.51.2.22.4.22 | ScalarchassisNoOfPMsSupported | read-only | mandatory | Number of power modules (PMs) supported. |
| 1.3.6.1.4.1.2.3.51.2.22.4.23 | ScalarchassisNoOfRearLEDCardsSupported | read-only | mandatory | Number of rear LED cards supported. |
| 1.3.6.1.4.1.2.3.51.2.22.4.24 | ScalarchassisNoOfChassisFansSupported | read-only | mandatory | Number of chassis fans supported. |
| 1.3.6.1.4.1.2.3.51.2.22.4.25 | ScalarchassisBayDevicesInstalled | read-only | mandatory | The bay devices that are installed in the chassis. The bay devices are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as l… |
| 1.3.6.1.4.1.2.3.51.2.22.4.29 | ScalarchassisSMsInstalled | read-only | mandatory | The switch modules that are installed on the chassis. The switch modules are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that i… |
| 1.3.6.1.4.1.2.3.51.2.22.4.30 | ScalarchassisMMsInstalled | read-only | mandatory | The management modules that are installed on the chassis. The management modules are listed as a bitmap. The bitmap is a string containing a list of 1's and 0'… |
| 1.3.6.1.4.1.2.3.51.2.22.4.31 | ScalarchassisPMsInstalled | read-only | mandatory | The power modules that are installed on the chassis. The power modules are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is … |
| 1.3.6.1.4.1.2.3.51.2.22.4.32 | ScalarchassisRearLEDCardInstalled | read-only | mandatory | Indicates whether at least one rear LED card is installed. |
| 1.3.6.1.4.1.2.3.51.2.22.4.33 | ScalarchassisFansInstalled | read-only | mandatory | The chassis fans that are installed on the chassis. They are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the… |
| 1.3.6.1.4.1.2.3.51.2.22.4.34 | ScalarchassisActiveMM | read-only | mandatory | The active management module (MM). |
| 1.3.6.1.4.1.2.3.51.2.22.4.37 | ScalarchassisFPsInstalled | read-only | deprecated | This object is deprecated because the power modules' fan packs are integrated into the power modules and are not removable as on previous power modules. The fa… |
| 1.3.6.1.4.1.2.3.51.2.22.4.38 | ScalarchassisType | read-only | mandatory | The type of the chassis. This MIB object should be used in conjunction with chassisSubType MIB object to determine the characteristic of the chassis. |
| 1.3.6.1.4.1.2.3.51.2.22.4.39 | ScalarchassisSubtype | read-only | mandatory | The subtype of the chassis. This MIB object should be used in conjunction with chassisType MIB object to determine the characteristic of the chassis. |
| 1.3.6.1.4.1.2.3.51.2.22.4.52 | ScalarchassisNoOfRearLEDCardsInstalled | read-only | mandatory | The rear LED cards that are installed on the chassis. |
| 1.3.6.1.4.1.2.3.51.2.22.4.53 | ScalarchassisRoom | read-write | mandatory | The name of the room where the chassis is located. Maximum 23 characters for name plus NULL termination. |
| 1.3.6.1.4.1.2.3.51.2.22.4.54 | ScalarchassisName | read-write | mandatory | The name of the chassis. Maximum 15 character long plus NULL termination. |
| 1.3.6.1.4.1.2.3.51.2.22.4.55 | ScalarchassisRack | read-write | mandatory | The name of the room where the chassis is located. Maximum 23 characters for name plus NULL termination. |
| 1.3.6.1.4.1.2.3.51.2.22.4.56 | ScalarchassisLowestU | read-write | mandatory | The lowest U position that is occupied in the rack. |
| 1.3.6.1.4.1.2.3.51.2.22.4.57 | ScalarchassisUHeight | read-only | mandatory | The height of the chassis in 'U' units. |
| 1.3.6.1.4.1.2.3.51.2.22.5 | NodemanagementModule | |||
| 1.3.6.1.4.1.2.3.51.2.22.5.1 | TablemmStatusTable | not-accessible | mandatory | Table of the management module status. |
| 1.3.6.1.4.1.2.3.51.2.22.5.1.1 | RowmmStatusEntry | not-accessible | mandatory | Management module status entry. |
| 1.3.6.1.4.1.2.3.51.2.22.5.1.1.1 | ColumnmmStatusIndex | read-only | mandatory | Management module status index. |
| 1.3.6.1.4.1.2.3.51.2.22.5.1.1.2 | ColumnmmPresent | read-only | mandatory | Management module current status. |
| 1.3.6.1.4.1.2.3.51.2.22.5.1.1.3 | ColumnmmExtIpAddress | read-only | mandatory | Management module external IP address. NOTE: The IPv6 addresses assigned to the MM may be viewed with the extEthernetInterfaceIPv6 objects |
| 1.3.6.1.4.1.2.3.51.2.22.5.1.1.4 | ColumnmmPrimary | read-only | mandatory | Indicates if this Management module is a primary or not. NOTE: If there is no standby MM, this value defaults to primary. |
| 1.3.6.1.4.1.2.3.51.2.22.5.1.1.5 | ColumnmmHealthState | read-only | mandatory | The health state for the management module. 0 = unknown, 1 = good, 2 = warning, 3 = bad. |
| 1.3.6.1.4.1.2.3.51.2.22.8 | NodefirmwareInformation | |||
| 1.3.6.1.4.1.2.3.51.2.22.8.1 | NodesmFirmwareInformation | |||
| 1.3.6.1.4.1.2.3.51.2.22.8.1.1 | TablesmFirmwareInfoTable | not-accessible | mandatory | Switch Module firmware image information. |
| 1.3.6.1.4.1.2.3.51.2.22.8.1.1.1 | RowsmFirmwareInfoEntry | not-accessible | mandatory | Switch Module firmware image information table entry |
| 1.3.6.1.4.1.2.3.51.2.22.8.1.1.1.1 | ColumnsmFirmwareInfoIndex | read-only | mandatory | Sequence index in the firmware table. |
| 1.3.6.1.4.1.2.3.51.2.22.8.1.1.1.2 | ColumnsmFirmwareInfoModIndex | read-only | mandatory | Switch Module number. |
| 1.3.6.1.4.1.2.3.51.2.22.8.1.1.1.3 | ColumnsmFirmwareInfoImageIndex | read-only | mandatory | Switch Module firmware image index. |
| 1.3.6.1.4.1.2.3.51.2.22.8.1.1.1.4 | ColumnsmFirmwareInfoImageName | read-write | mandatory | Switch Module firmware image name |
| 1.3.6.1.4.1.2.3.51.2.22.9 | NodefirmwareUpdate | |||
| 1.3.6.1.4.1.2.3.51.2.22.9.1 | ScalarfirmwareUpdateTarget | read-write | mandatory | Target module whose firmware will be updated. NOTE: Some switch modules do not allow firmware update. When firmware update is attempted on those switch modules… |
| 1.3.6.1.4.1.2.3.51.2.22.9.2 | ScalarfirmwareUpdateTftpServer | read-write | mandatory | If flashing via the legacy method using a tftp server, then set the IP address or host name of the TFTP server where the firmware file resides. The address mus… |
| 1.3.6.1.4.1.2.3.51.2.22.9.3 | ScalarfirmwareUpdateFileName | read-write | mandatory | File name of the firmware file. |
| 1.3.6.1.4.1.2.3.51.2.22.9.4 | ScalarfirmwareUpdateStart | read-write | mandatory | Start updating the firmware of the specified target module. Using execute or execute-with-reboot will cause the SNMP client to wait for the firmware update to … |
| 1.3.6.1.4.1.2.3.51.2.22.9.5 | ScalarfirmwareUpdateStatus | read-only | mandatory | Get the status of the last firmware update which was initiated through SNMP method. |
| 1.3.6.1.4.1.2.3.51.2.22.9.6 | ScalarstandbyFirmwareUpdateStatus | read-only | mandatory | Get the current status of the firmware update for the standby MM. NOTE: This only applies to systems with a standby MM. |
| 1.3.6.1.4.1.2.3.51.2.22.9.7 | ScalarfirmwareImageNumber | read-write | mandatory | If the module can upload more than one image, an image number must be specified after setting the firmware target. Please refer to the firmwareInformation sect… |
| 1.3.6.1.4.1.2.3.51.2.22.9.8 | ScalarfirmwareActiveImage | read-write | mandatory | If the module can upload more than one image, an active image number must be specified. Please refer to the firmwareInformation section. NOTE: Value returned f… |
| 1.3.6.1.4.1.2.3.51.2.22.9.9 | ScalarfirmwareUpdateServer | read-write | mandatory | Contains the fully qualified remote location of the firmware packet file. Use firmwareUpdateFileName to specify the filename. A fully qualified remote location… |
| 1.3.6.1.4.1.2.3.51.2.22.11 | NodefileManagement | |||
| 1.3.6.1.4.1.2.3.51.2.22.11.1 | NodefileTopology | |||
| 1.3.6.1.4.1.2.3.51.2.22.11.1.1 | ScalarcurrentDirectory | read-write | mandatory | Specifies the directory name for listing the requested files. |
| 1.3.6.1.4.1.2.3.51.2.22.11.1.2 | TablefileDetailsTable | not-accessible | mandatory | A table of all the files in the specified directory. |
| 1.3.6.1.4.1.2.3.51.2.22.11.1.2.1 | RowfileDetailsEntry | not-accessible | mandatory | File details entry. |
| 1.3.6.1.4.1.2.3.51.2.22.11.1.2.1.1 | ColumnfileIndex | read-only | mandatory | File sequence index. |
| 1.3.6.1.4.1.2.3.51.2.22.11.1.2.1.2 | ColumnfileName | read-only | mandatory | File name. |
| 1.3.6.1.4.1.2.3.51.2.22.11.1.2.1.3 | ColumnfileLastUpdate | read-only | mandatory | Date of the latest file update. |
| 1.3.6.1.4.1.2.3.51.2.22.11.1.2.1.4 | ColumnfileSize | read-only | mandatory | File size in bytes. |
| 1.3.6.1.4.1.2.3.51.2.22.11.3 | ScalarfileManagementCmd | read-write | mandatory | This field will execute the selected operations on the files. The following operation is supported: DEL name - delete a file Examples: - to delete the file nam… |
| 1.3.6.1.4.1.2.3.51.2.22.11.6 | ScalarfileSystemSpaceAvailable | read-only | mandatory | This field displays the available space of the MM file system. |
| 1.3.6.1.4.1.2.3.51.2.22.12 | NodecmeRemoteChassis | |||
| 1.3.6.1.4.1.2.3.51.2.22.12.1 | TablecmeRemoteChassisTable | not-accessible | mandatory | This table is used to provide the discovered MMs based on the new, extended SLP response information. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1 | RowcmeRemoteChassisEntry | not-accessible | mandatory | Remote chassis entry |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.1 | ColumncmeRemoteChassisIndex | read-only | mandatory | Remote chassis discovery sequence index. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.2 | ColumncmeSystemName | read-only | mandatory | System name for this discovery management module. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.3 | ColumncmeType | read-only | mandatory | Management module service processor type. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.4 | ColumncmeSerial | read-only | mandatory | Management module serial number. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.5 | ColumncmeFru | read-only | mandatory | Management module Field-Replaceable number. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.6 | ColumncmeUuid | read-only | mandatory | Management module UUID. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.7 | ColumncmeSlot | read-only | mandatory | Management module slot. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.8 | ColumncmeMidPid | read-only | mandatory | Management module Mid-plane Pid. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.9 | ColumncmeMacAddress | read-only | mandatory | Management module MAC address. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.10 | ColumncmeChassisSerial | read-only | mandatory | Chassis serial number. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.11 | ColumncmeChassisFru | read-only | mandatory | Chassis Field-Replaceable number. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.12 | ColumncmeChassisMachineTypeMode | read-only | mandatory | Chassis machine type and model number. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.13 | ColumncmeSystemStatus | read-only | mandatory | Chassis status. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.14 | ColumncmeChassisUuid | read-only | mandatory | Chassis UUID. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.15 | ColumncmeChassisMidPid | read-only | mandatory | Chassis mid-plane ID. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.16 | ColumncmeChassisId | read-only | mandatory | Chassis ID. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.17 | ColumncmeChassisLocation | read-only | mandatory | Chassis location information. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.18 | ColumncmeChassisRoomId | read-only | mandatory | Chassis room ID. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.19 | ColumncmeChassisRackId | read-only | mandatory | Chassis rack ID. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.20 | ColumncmeChassisUser | read-only | mandatory | Chassis user information. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.21 | ColumncmeChassisFruList | read-only | mandatory | Chassis FRU list. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.22 | ColumncmeFirmwareVersion | read-only | mandatory | Firmware version of the discovery management module. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.23 | ColumncmeChassisType | read-only | mandatory | Chassis type. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.24 | ColumncmeIpv4Status | read-only | mandatory | A flag to state if IPv4 is enabled |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.25 | ColumncmeIpv4Addresses | read-only | mandatory | The IPv4 addresses configured for the chassis. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.26 | ColumncmeIpv4AddressesFloat | read-only | mandatory | The floating IPv4 addresses configured for the chassis. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.27 | ColumncmeIpv4Protocols | read-only | mandatory | The IPv4 protocols configured for the chassis. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.28 | ColumncmeIpv6Status | read-only | mandatory | A flag to state if IPv6 is enabled |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.29 | ColumncmeIpv6Addresses | read-only | mandatory | The IPv6 addresses configured for the chassis. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.30 | ColumncmeIpv6AddressesFloat | read-only | mandatory | The floating IPv6 addresses configured for the chassis. |
| 1.3.6.1.4.1.2.3.51.2.22.12.1.1.31 | ColumncmeIpv6Protocols | read-only | mandatory | The IPv6 protocols configured for the chassis. |
| 1.3.6.1.4.1.2.3.51.2.22.12.2 | ScalarchassisDiscovery | read-write | mandatory | Discovery of remote Chassis. NOTE: Value returned for the GET command is meaningless for this MIB object. |
| 1.3.6.1.4.1.2.3.51.2.22.31 | NodecomponentPower | |||
| 1.3.6.1.4.1.2.3.51.2.22.31.1 | TablecomponentPowerTable | not-accessible | mandatory | Table of component remote power control information. Contains power on/off enablement status for each component. |
| 1.3.6.1.4.1.2.3.51.2.22.31.1.1 | RowcomponentPowerEntry | not-accessible | mandatory | Component power/restart table entry |
| 1.3.6.1.4.1.2.3.51.2.22.31.1.1.1 | ColumncomponentPowerTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.22.31.1.1.2 | ColumncomponentPowerName | read-only | mandatory | The name of the component as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.31.1.1.3 | ColumncomponentPowerState | read-only | mandatory | Indicates the power state of the component specified. If the state cannot be determined, the unknown(255) is returned. |
| 1.3.6.1.4.1.2.3.51.2.22.31.1.1.4 | ColumncomponentPowerAction | read-write | mandatory | Control the power state of a specific component. none: No action, value returned for GET. off: Power-off component. on: Power-on component. softoff: Shutdown O… |
| 1.3.6.1.4.1.2.3.51.2.22.31.1.1.5 | ColumncomponentPowerEnableSMSBootMenu | read-write | mandatory | Enables/disables a component restart to the SMS boot menu. Setting this object to 'enable(1)' will cause a reboot of the node to the SMS menu. This option is n… |
| 1.3.6.1.4.1.2.3.51.2.22.31.2 | ScalarcomponentPowerTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentPowerTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.31.6 | TablecomponentPowerDetailsTable | not-accessible | mandatory | Table of component power detail information. |
| 1.3.6.1.4.1.2.3.51.2.22.31.6.1 | RowcomponentPowerDetailsEntry | not-accessible | mandatory | Component power Details table entry |
| 1.3.6.1.4.1.2.3.51.2.22.31.6.1.1 | ColumncomponentPowerDetailsTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.22.31.6.1.2 | ColumncomponentPowerDetailsName | read-only | mandatory | The name of the component as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.31.6.1.3 | ColumncomponentPowerDetailsMaxPowerConfig | read-write | mandatory | Component Module Details Table Maximum Power Configuration. Allow the user to set the maximum power that can be used by the component. This function is also kn… |
| 1.3.6.1.4.1.2.3.51.2.22.31.6.1.4 | ColumncomponentPowerDetailsEffectiveClockRate | read-only | mandatory | Component Module Details Table Effective CPU Clock Rate applies to DPM components only. It displays processor's effective clock rate based on sample interval. … |
| 1.3.6.1.4.1.2.3.51.2.22.31.6.1.5 | ColumncomponentPowerDetailsMaximumClockRate | read-only | mandatory | Component Module Details Table Maximum CPU Clock Rate applies to DPM components only. It displays processor's maximum clock rate based on sample interval. Note… |
| 1.3.6.1.4.1.2.3.51.2.22.31.6.1.6 | ColumncomponentPowerDetailsPowerSaverMode | read-write | mandatory | When enabled, the static low power saver mode allows the component to selectively alter its operating voltage and frequency to reduce power consumption. This f… |
| 1.3.6.1.4.1.2.3.51.2.22.31.6.1.7 | ColumncomponentPowerDetailsDynamicPowerSaver | read-write | mandatory | When enabled, Dynamic Power Saver allows the voltage and frequency of the CPUs on the component to be controlled based on how busy the CPU is. This feature is … |
| 1.3.6.1.4.1.2.3.51.2.22.31.6.1.8 | ColumncomponentPowerDetailsDynamicPowerFavorPerformanceOverPower | read-write | mandatory | When enabled, Dynamic Power Favor Performance Over Power supports a max performance mode that pushes the system past its nominal CPU frequency when CPU and mem… |
| 1.3.6.1.4.1.2.3.51.2.22.31.6.1.9 | ColumncomponentPowerDetailsPowerControl | read-write | mandatory | This object is used to get or set the power control setting on a component. If dynamic power mgmt is not supported on a component, notApplicable(255) will be r… |
| 1.3.6.1.4.1.2.3.51.2.22.31.6.1.10 | ColumncomponentPowerDetailsPcapMin | read-only | mandatory | Component Module Details Table power capping Minimum value in watts. The component must support the advanced power management feature. If the value of Pcap Min… |
| 1.3.6.1.4.1.2.3.51.2.22.31.6.1.11 | ColumncomponentPowerDetailsPcapGuaranteedMin | read-only | mandatory | Component Module Details Table power capping Guaranteed Minimum value in watts. The component must support the advanced power management feature. If the value … |
| 1.3.6.1.4.1.2.3.51.2.22.31.6.1.12 | ColumncomponentPowerDetailsPcapMax | read-only | mandatory | Component Module Details Table power capping Maximum value in watts. The component must support the advanced power management feature. If the value is '<max1> … |
| 1.3.6.1.4.1.2.3.51.2.22.31.6.1.13 | ColumncomponentPowerDetailsStaticCap | read-only | mandatory | Component Module Details Table static capabilities list. This is a list of five power management capabilities that the component may or may not support. The li… |
| 1.3.6.1.4.1.2.3.51.2.22.31.6.1.14 | ColumncomponentPowerDetailsRuntimeCap | read-only | mandatory | Component Module Details Table run-time capabilities list. If the component supports the capability as indicated in the static capability information, the user… |
| 1.3.6.1.4.1.2.3.51.2.22.31.7 | ScalarcomponentPowerDetailsTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentPowerDetailsTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.32 | NodecomponentConfiguration | |||
| 1.3.6.1.4.1.2.3.51.2.22.32.1 | TablecomponentBayDataTable | not-accessible | mandatory | Table of component bay User data information. Contains user provided data for each component bay. |
| 1.3.6.1.4.1.2.3.51.2.22.32.1.1 | RowcomponentBayDataEntry | not-accessible | mandatory | Component Bay Data table entry |
| 1.3.6.1.4.1.2.3.51.2.22.32.1.1.1 | ColumncomponentBayDataTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.22.32.1.1.2 | ColumncomponentBayDataName | read-only | mandatory | The name of the component as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.32.1.1.3 | ColumncomponentBayDataStatus | read-only | mandatory | This shows Bay Data (BD) Status. 0 means the component fully supports BD. 1 means that the component's BIOS does not support BD. 2 means that there is no compo… |
| 1.3.6.1.4.1.2.3.51.2.22.32.1.1.4 | ColumncomponentBayData | read-write | mandatory | A null terminated string that defines the component Bay Data. This data is puched to the components's BSMP and SMBIOS structures, where it can be used by the c… |
| 1.3.6.1.4.1.2.3.51.2.22.32.2 | ScalarcomponentBayDataTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentBayDataTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.32.6 | TablecomponentEthOverUSBInterfaceTable | not-accessible | mandatory | Table of blade Service Processor's Ethernet over USB interface. |
| 1.3.6.1.4.1.2.3.51.2.22.32.6.1 | RowcomponentEthOverUSBInterfaceEntry | not-accessible | mandatory | Blade Service Processor's Ethernet over USB interface entry. |
| 1.3.6.1.4.1.2.3.51.2.22.32.6.1.1 | ColumncomponentEthOverUSBInterfaceTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.22.32.6.1.2 | ColumncomponentEthOverUSBInterfaceName | read-only | mandatory | The name of the component as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.32.6.1.3 | ColumncomponentEthOverUSBInterfaceEnable | read-write | mandatory | This object allows the user to view the status of, and enable or disable, a component's interface on Ethernet-over-USB. NOTE: If the component either does not … |
| 1.3.6.1.4.1.2.3.51.2.22.32.7 | ScalarcomponentEthOverUSBInterfaceTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentEthOverUSBInterfaceTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.32.11 | TablecomponentConfigurationTable | not-accessible | mandatory | Table of component configuration information. |
| 1.3.6.1.4.1.2.3.51.2.22.32.11.1 | RowcomponentConfigurationEntry | not-accessible | mandatory | Component configuration table entry |
| 1.3.6.1.4.1.2.3.51.2.22.32.11.1.1 | ColumncomponentConfigurationTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.22.32.11.1.2 | ColumncomponentConfigurationName | read-write | mandatory | The name of the component as a null terminated string. This object is configurable. |
| 1.3.6.1.4.1.2.3.51.2.22.32.11.1.3 | ColumncomponentConfigurationActiveBootMode | read-only | mandatory | Indicates the active copy of the firmware from which the component is booting. NOTE: Some components do not support the automatic boot recovery. It displays 'n… |
| 1.3.6.1.4.1.2.3.51.2.22.32.11.1.4 | ColumncomponentConfigurationPendingBootMode | read-write | mandatory | Indicates the copy of the firmware from which the component will boot after the next reboot. NOTE: Some components do not support the automatic boot recovery. … |
| 1.3.6.1.4.1.2.3.51.2.22.32.11.1.5 | ColumncomponentConfigurationAutoPowerOn | read-write | mandatory | Component auto-power on policy. - restore: component will be powered on which were previously on. - auto: component will automatically be powered on when power… |
| 1.3.6.1.4.1.2.3.51.2.22.32.11.1.6 | ColumncomponentConfigurationPowerOnRestartDelay | read-write | mandatory | Restart delay (in seconds) when power is applied to a component. |
| 1.3.6.1.4.1.2.3.51.2.22.32.11.1.7 | ColumncomponentConfigurationLocalPowerControlEnable | read-write | mandatory | Component local power control enablement status. |
| 1.3.6.1.4.1.2.3.51.2.22.32.11.1.8 | ColumncomponentConfigurationWakeOnLanControlEnable | read-write | mandatory | Component Wake On LAN enablement status. If WOL is not supported by the component, it displays 'notApplicable' and WOL can not be enabled or disabled. |
| 1.3.6.1.4.1.2.3.51.2.22.32.12 | ScalarcomponentConfigurationTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentConfigurationTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16 | NodecomponentNetworkConfiguration | |||
| 1.3.6.1.4.1.2.3.51.2.22.32.16.1 | TablecomponentIPv4ConfigTable | not-accessible | mandatory | Table of all components' network interfaces. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1 | RowcomponentIPv4ConfigEntry | not-accessible | mandatory | Component configuration table entry |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.1 | ColumncomponentIPv4ConfigTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.2 | ColumncomponentIPv4ConfigPortIndex | read-only | mandatory | The physical port number of the given entry. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.3 | ColumncomponentIPv4ConfigName | read-only | mandatory | The name of the component as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.4 | ColumncomponentIPv4ConfigPortLabel | read-only | mandatory | Show string label that identifies the interface. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.5 | ColumncomponentIPv4ConfigPhysicalLinkStatus | read-only | mandatory | Indicates whether this network interface port is up or down. If this network interface doesn't support up/down, show 'notApplicable(255)'. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.6 | ColumncomponentIPv4ConfigPhysicalLinkState | read-write | mandatory | Configuration object for requesting the physical port to be either, down(0), up(1) or loopback(2). To get the current status of a physical port, use the object… |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.7 | ColumncomponentIPv4ConfigIPAddr | read-write | mandatory | Show/modify current IP address of the component network interface. Note that only if the componentIPv4ConfigPhysicalLinkStatus is 'up(1)' and the componentIPv4… |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.8 | ColumncomponentIPv4ConfigSubnetMask | read-write | mandatory | Show or modifie current subnet mask of the component network interface. Note that only if the componentIPv4ConfigPhysicalLinkStatus is 'up(1)' and the componen… |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.9 | ColumncomponentIPv4ConfigGatewayAddr | read-write | mandatory | Show or modify current IP gateway of the component network interface. Note that only if the componentIPv4ConfigPhysicalLinkStatus is 'up(1)' and the componentI… |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.10 | ColumncomponentIPv4ConfigVlanId | read-write | mandatory | This is the Virtual LAN ID for supported network interface cards (NICs). The range of valid VLAN ID's is 0 to 4095. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.11 | ColumncomponentIPv4ConfigDHCPEnable | read-write | mandatory | IP config method on the component network interface to modify mode to static IP, DHCP and 'try DHCP then try static'. If this network interface doesn't support… |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.12 | ColumncomponentIPv4ConfigMACAddr | read-only | mandatory | Show the component network interface MAC address. If this network interface doesn't support MAC, show 'notApplicable'. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.2 | ScalarcomponentIPv4ConfigTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentIPv4ConfigTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11 | NodecomponentIPv6Config | |||
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.1 | TablecomponentIPv6ConfigTable | not-accessible | mandatory | A table of IPv6 configuration options for components. NOTE: This MIB object is not applicable to components that do not support IPv6. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.1.1 | RowcomponentIPv6ConfigEntry | not-accessible | mandatory | IPv6 configuration options for a component. NOTE: This MIB object is not applicable to components that do not support IPv6. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.1.1.1 | ColumncomponentIPv6ConfigTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.1.1.2 | ColumncomponentIPv6ConfigPortIndex | read-only | mandatory | The physical port number of the given entry |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.1.1.3 | ColumncomponentIPv6ConfigName | read-only | mandatory | The name of the component as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.1.1.4 | ColumncomponentIPv6ConfigEnabled | read-write | mandatory | Enables/Disables IPv6 support on the component. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.1.1.5 | ColumncomponentIPv6ConfigStatic | read-write | mandatory | Enables/Disables IPv6 static configuration support on the component. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.1.1.6 | ColumncomponentDHCPv6ConfigEnabled | read-write | mandatory | Enables/Disables DHCPv6 address configuration support on the component. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.1.1.7 | ColumncomponentIPv6ConfigStatelessEnabled | read-write | mandatory | Enables/Disables IPv6 stateless auto-configuration support on the component. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.2 | ScalarcomponentIPv6ConfigTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentIPv6ConfigTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6 | TablecomponentIPv6AddressTable | not-accessible | mandatory | A table of assigned IPv6 addresses for components. NOTE: This MIB object is not applicable to components that do not support IPv6. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6.1 | RowcomponentIPv6AddressEntry | not-accessible | mandatory | The assigned IPv6 address for a given component. NOTE: This MIB object is not applicable to components that do not support IPv6. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6.1.1 | ColumncomponentIPv6AddressTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6.1.2 | ColumncomponentIPv6AddressPortIndex | read-only | mandatory | The component's physical port number for the given entry. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6.1.3 | ColumncomponentIPv6AddressEntryIndex | read-only | mandatory | The component's address entry index. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6.1.4 | ColumncomponentIPv6AddressName | read-only | mandatory | The name of the component as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6.1.5 | ColumncomponentIPv6AddressType | read-only | mandatory | The address type. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6.1.6 | ColumncomponentIPv6Address | read-write | mandatory | The assigned IPv6 address. Note: 'write' is for static ipv6 only. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6.1.7 | ColumncomponentIPv6AddressPrefixLen | read-write | mandatory | The prefix length for the given address. Note: 'write' is for static ipv6 only. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6.1.8 | ColumncomponentIPv6AddressDefaultRoute | read-write | mandatory | The default route used for the given address. Note: 'write' is for static ipv6 only. |
| 1.3.6.1.4.1.2.3.51.2.22.32.16.11.7 | ScalarcomponentIPv6AddressTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentIPv6AddressTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.32.20 | TablecomponentTimeTable | not-accessible | mandatory | Table of Component NTP Configuration. |
| 1.3.6.1.4.1.2.3.51.2.22.32.20.1 | RowcomponentTimeEntry | not-accessible | mandatory | Component NTP Configuration entry. |
| 1.3.6.1.4.1.2.3.51.2.22.32.20.1.1 | ColumncomponentTimeTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.22.32.20.1.2 | ColumncomponentTimeName | read-only | mandatory | The name of the component as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.32.20.1.3 | ColumncomponentTimeNTPEnable | read-write | mandatory | This object allows the user to view the status of, and enable or disable, a component's ability to have it's NTP information updated by the CMM. NOTE: If the c… |
| 1.3.6.1.4.1.2.3.51.2.22.32.20.1.4 | ColumncomponentTimeNTPFrequency | read-write | mandatory | This object allows the user to view or set the synchronization frequency (in minutes) of the NTP information update from the CMM. NOTE: If the component either… |
| 1.3.6.1.4.1.2.3.51.2.22.32.21 | ScalarcomponentTimeTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentTimeTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.32.26 | TablecomponentSolTable | not-accessible | mandatory | Component Serial-over-LAN (SOL) configuration table. |
| 1.3.6.1.4.1.2.3.51.2.22.32.26.1 | RowcomponentSolEntry | not-accessible | mandatory | Component Serial-over-LAN (SOL) configuration entry. |
| 1.3.6.1.4.1.2.3.51.2.22.32.26.1.1 | ColumncomponentSolTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.22.32.26.1.2 | ColumncomponentSolName | read-only | mandatory | The name of the component as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.32.26.1.3 | ColumncomponentSolEnable | read-write | mandatory | Disable or enable the Serial-over-LAN (SOL) on a component. |
| 1.3.6.1.4.1.2.3.51.2.22.32.26.1.4 | ColumncomponentSolIpAddr | read-only | deprecated | This is deprecated in favor of componentSolIpAddr. IP address of the component derived from the IP address range for the system management processors on the co… |
| 1.3.6.1.4.1.2.3.51.2.22.32.26.1.5 | ColumncomponentSolSessionStatus | read-only | mandatory | Status of a Serial-over-LAN (SOL) session: solSessionNotReady: No SOL session connected to the component. solSessionReady: There is a SOL session to the compon… |
| 1.3.6.1.4.1.2.3.51.2.22.32.26.1.6 | ColumncomponentSolCapability | read-only | mandatory | Display whether or not the component supports the Serial-over-LAN (SOL) feature. |
| 1.3.6.1.4.1.2.3.51.2.22.32.26.1.7 | ColumncomponentSolIpAddr6 | read-only | mandatory | IPv6 address of the blade. |
| 1.3.6.1.4.1.2.3.51.2.22.32.26.1.8 | ColumncomponentSolRetryInterval | read-only | mandatory | Retry interval time in miliseconds. |
| 1.3.6.1.4.1.2.3.51.2.22.32.26.1.9 | ColumncomponentSolRetryCount | read-only | mandatory | Retry count. |
| 1.3.6.1.4.1.2.3.51.2.22.32.26.1.10 | ColumncomponentSolBytesSent | read-only | mandatory | Number of bytes sent. |
| 1.3.6.1.4.1.2.3.51.2.22.32.26.1.11 | ColumncomponentSolBytesReceived | read-only | mandatory | Number of bytes received. |
| 1.3.6.1.4.1.2.3.51.2.22.32.26.1.12 | ColumncomponentSolDestinationMAC | read-only | mandatory | MAC address of the blade. |
| 1.3.6.1.4.1.2.3.51.2.22.32.26.1.13 | ColumncomponentSolConsoleUserId | read-only | mandatory | Sol console user name. |
| 1.3.6.1.4.1.2.3.51.2.22.32.26.1.14 | ColumncomponentSolConsoleLoginFrom | read-only | mandatory | The location information from where the SOL console is logged in. |
| 1.3.6.1.4.1.2.3.51.2.22.32.26.1.15 | ColumncomponentSolConsoleLoginStart | read-only | mandatory | The time that SOL console starts. |
| 1.3.6.1.4.1.2.3.51.2.22.32.26.1.16 | ColumncomponentSolConsoleLoginEnd | read-only | mandatory | The time that SOL console ends. |
| 1.3.6.1.4.1.2.3.51.2.22.32.27 | ScalarcomponentSolTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentSolTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.37 | NodecomponentMonitors | |||
| 1.3.6.1.4.1.2.3.51.2.22.37.1 | TablecomponentSystemStatusTable | not-accessible | mandatory | Table of component status information. |
| 1.3.6.1.4.1.2.3.51.2.22.37.1.1 | RowcomponentSystemStatusEntry | not-accessible | mandatory | Component system status entry |
| 1.3.6.1.4.1.2.3.51.2.22.37.1.1.1 | ColumncomponentStatusTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.22.37.1.1.2 | ColumncomponentStatusName | read-only | mandatory | The name of the component as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.37.1.1.3 | ColumncomponentStatusPowerState | read-only | mandatory | Indicates the power state of the component specified. |
| 1.3.6.1.4.1.2.3.51.2.22.37.1.1.4 | ColumncomponentStatusHealthState | read-only | mandatory | The system health state for the component. Unknown: Component is in an undefined state. Good: Component is operating normally. Warning: One or more outstanding… |
| 1.3.6.1.4.1.2.3.51.2.22.37.1.1.5 | ColumncomponentStatusPowerEnable | read-only | mandatory | Power enable state for the component. |
| 1.3.6.1.4.1.2.3.51.2.22.37.1.1.6 | ColumncomponentStatusWakeOnLanEnable | read-only | mandatory | Wake on LAN enable state for the component. |
| 1.3.6.1.4.1.2.3.51.2.22.37.1.1.7 | ColumncomponentStatusWidth | read-only | mandatory | The width of the component including any supplement component attached to it |
| 1.3.6.1.4.1.2.3.51.2.22.37.1.1.21 | ColumncomponentStatusIOCompatibility | read-only | mandatory | I/O compatibility status for the component. The possible values and their meanings are as follows: unknown: This indicates a communication error for the compon… |
| 1.3.6.1.4.1.2.3.51.2.22.37.1.1.22 | ColumncomponentStatusInventoryReady | read-only | mandatory | When a component management controller or the MM is reset, the component inventory data is refreshed in the MM database. This includes items like IBM VPD (e.g.… |
| 1.3.6.1.4.1.2.3.51.2.22.37.1.1.23 | ColumncomponentStatusBootCountPowerOnTimeBoots | read-write | mandatory | Blade boot count. This is valid for blade components and otherwise is undefined. Writing this value resets the boot count to zero. |
| 1.3.6.1.4.1.2.3.51.2.22.37.1.1.24 | ColumncomponentStatusBootCountPowerOnTimeSecs | read-write | mandatory | Blade power on time in seconds. This is valid for blade components and otherwise is undefined. Writing this value resets the power on time to zero. |
| 1.3.6.1.4.1.2.3.51.2.22.37.2 | ScalarcomponentSystemStatusTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentSystemStatusTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.37.6 | TablecomponentHealthSummaryTable | not-accessible | mandatory | Table of component health summary information. Contains information about the overall component health status. Each component contains a list of critical or wa… |
| 1.3.6.1.4.1.2.3.51.2.22.37.6.1 | RowcomponentHealthSummaryEntry | not-accessible | mandatory | Component health summary entry |
| 1.3.6.1.4.1.2.3.51.2.22.37.6.1.1 | ColumncomponentHealthTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.22.37.6.1.2 | ColumncomponentHealthEventIndex | read-only | mandatory | An index for the critical or warning health events for a given component. |
| 1.3.6.1.4.1.2.3.51.2.22.37.6.1.3 | ColumncomponentHealthSummaryName | read-only | mandatory | The name of the component as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.37.6.1.4 | ColumncomponentHealthSummarySeverity | read-only | mandatory | System health summary severity of an event for the given component. |
| 1.3.6.1.4.1.2.3.51.2.22.37.6.1.5 | ColumncomponentHealthSummaryDescription | read-only | mandatory | System health summary description of an event for the given component. |
| 1.3.6.1.4.1.2.3.51.2.22.37.6.1.6 | ColumncomponentHealthSummaryDateTime | read-only | mandatory | System health summary date time of an event for the given component. |
| 1.3.6.1.4.1.2.3.51.2.22.37.6.1.7 | ColumncomponentHealthSummaryEventID | read-only | mandatory | System health summary event ID of an event for the given component. |
| 1.3.6.1.4.1.2.3.51.2.22.37.7 | ScalarcomponentHealthSummaryTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentHealthSummaryTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.37.11 | TablecomponentMACAddressTable | not-accessible | mandatory | Table of MAC address VPD information for each component. |
| 1.3.6.1.4.1.2.3.51.2.22.37.11.1 | RowcomponentMACAddressEntry | not-accessible | mandatory | Component MAC address table entry |
| 1.3.6.1.4.1.2.3.51.2.22.37.11.1.1 | ColumncomponentMACAddressTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.22.37.11.1.2 | ColumncomponentMACAddressIndex | read-only | mandatory | Each component may have one or more MAC address VPD values associated with it, and this index object identifies the particular instance. |
| 1.3.6.1.4.1.2.3.51.2.22.37.11.1.3 | ColumncomponentMACAddressName | read-only | mandatory | The name of the component as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.37.11.1.4 | ColumncomponentMACAddress | read-only | mandatory | The MAC address VPD value for this component and index. The value is a null terminated string. For IOMs which are members of a stack, this field is not applica… |
| 1.3.6.1.4.1.2.3.51.2.22.37.12 | ScalarcomponentMACAddressTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentMACAddressTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.37.13 | TablecomponentUniqueIDsTable | not-accessible | mandatory | Table of unique ID information for each component. |
| 1.3.6.1.4.1.2.3.51.2.22.37.13.1 | RowcomponentUniqueIDsEntry | not-accessible | mandatory | Component unique ID table entry |
| 1.3.6.1.4.1.2.3.51.2.22.37.13.1.1 | ColumncomponentUniqueIDsTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.22.37.13.1.2 | ColumncomponentUniqueIDsIndex | read-only | mandatory | Each component may have one or more unique ID values associated with it, and this index object identifies the particular instance. |
| 1.3.6.1.4.1.2.3.51.2.22.37.13.1.3 | ColumncomponentUniqueIDsName | read-only | mandatory | The name of the component as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.37.13.1.4 | ColumncomponentUniqueIDsType | read-only | mandatory | Type of the unique ID in the object, componentUniqueIDsValue. The type is one of the following: World Wide Name (wwn), Global Unique IDs (guid) or Serial Attac… |
| 1.3.6.1.4.1.2.3.51.2.22.37.13.1.5 | ColumncomponentUniqueIDsValue | read-only | mandatory | The unique ID value for this component and index. The value is a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.37.14 | ScalarcomponentUniqueIDsTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentUniqueIDsTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.37.16 | TablecomponentVoltagesTable | not-accessible | mandatory | Table of component voltage sensor information. |
| 1.3.6.1.4.1.2.3.51.2.22.37.16.1 | RowcomponentVoltagesEntry | not-accessible | mandatory | Component voltages entry. |
| 1.3.6.1.4.1.2.3.51.2.22.37.16.1.1 | ColumncomponentVoltagesTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.22.37.16.1.2 | ColumncomponentVoltagesSensorIndex | read-only | mandatory | An index for the critical or warning health events for a given component. |
| 1.3.6.1.4.1.2.3.51.2.22.37.16.1.3 | ColumncomponentVoltagesComponentName | read-only | mandatory | The name of the component as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.37.16.1.4 | ColumncomponentVoltagesSensorLabel | read-only | mandatory | The label of the sensor as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.37.16.1.5 | ColumncomponentVoltagesSensorValue | read-only | mandatory | The value of the sensor as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.37.16.1.6 | ColumncomponentVoltagesLowWarningThreshold | read-only | mandatory | The low warning threshold of the sensor as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.37.16.1.7 | ColumncomponentVoltagesHighWarningThreshold | read-only | mandatory | The high warning threshold of the sensor as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.37.17 | ScalarcomponentVoltagesTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentVoltagesTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.37.21 | TablecomponentTemperaturesTable | not-accessible | mandatory | Table of component temperature sensor information. |
| 1.3.6.1.4.1.2.3.51.2.22.37.21.1 | RowcomponentTemperaturesEntry | not-accessible | mandatory | Component temperatures entry. |
| 1.3.6.1.4.1.2.3.51.2.22.37.21.1.1 | ColumncomponentTemperaturesTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.22.37.21.1.2 | ColumncomponentTemperaturesSensorIndex | read-only | mandatory | An index for the temperature Sensors for a given component. |
| 1.3.6.1.4.1.2.3.51.2.22.37.21.1.3 | ColumncomponentTemperaturesComponentName | read-only | mandatory | The name of the component as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.37.21.1.4 | ColumncomponentTemperaturesSensorLabel | read-only | mandatory | The label of the sensor as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.37.21.1.5 | ColumncomponentTemperaturesSensorValue | read-only | mandatory | The value of the sensor as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.37.21.1.6 | ColumncomponentTemperaturesWarningThreshold | read-only | mandatory | The warning threshold of the sensor as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.37.21.1.7 | ColumncomponentTemperaturesShutdownThreshold | read-only | mandatory | The Shutdown threshold of the sensor as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.37.21.1.8 | ColumncomponentTemperaturesWarningResetThreshold | read-only | mandatory | The Warning Reset threshold of the sensor as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.37.22 | ScalarcomponentTemperaturesTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentTemperaturesTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.37.26 | TablecomponentIOCompatibilityTable | not-accessible | mandatory | Table of component IO Compatibility information. |
| 1.3.6.1.4.1.2.3.51.2.22.37.26.1 | RowcomponentIOCompatibilityEntry | not-accessible | mandatory | Component IO compatibility entry. |
| 1.3.6.1.4.1.2.3.51.2.22.37.26.1.1 | ColumncomponentIOCompatibilityTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.22.37.26.1.2 | ColumncomponentIOCompatibilityIOMBay | read-only | mandatory | An index for the IO Compatibility modules for a given component. |
| 1.3.6.1.4.1.2.3.51.2.22.37.26.1.3 | ColumncomponentIOCompatibilityComponentName | read-only | mandatory | The name of the component as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.37.26.1.4 | ColumncomponentIOCompatibilityIOMPower | read-only | mandatory | The power state of the module specified in componentIOCompatibilityIOMBay. n/a if module not installed. |
| 1.3.6.1.4.1.2.3.51.2.22.37.26.1.5 | ColumncomponentIOCompatibilityIOMFabricType | read-only | mandatory | The fabric type of the module specified in componentIOCompatibilityIOMBay. |
| 1.3.6.1.4.1.2.3.51.2.22.37.26.1.6 | ColumncomponentIOCompatibilityFabricOnComponent | read-only | mandatory | The fabric type for this channel on the original component (may be onboard fabric or an expansion card). |
| 1.3.6.1.4.1.2.3.51.2.22.37.26.1.7 | ColumncomponentIOCompatibilityStatus | read-only | mandatory | The compatibility status between the component and the module specified in componentIOCompatibilityIOMBay. The possible values are: OK: No compatibility issues… |
| 1.3.6.1.4.1.2.3.51.2.22.37.27 | ScalarcomponentIOCompatibilityTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentIOCompatibilityTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.37.31 | TablenodeConnectivityTable | not-accessible | mandatory | Table of node connectivity information. This table provides information related to the node communication status. |
| 1.3.6.1.4.1.2.3.51.2.22.37.31.1 | RownodeConnectivityEntry | not-accessible | mandatory | Connectivity information for nodes. |
| 1.3.6.1.4.1.2.3.51.2.22.37.31.1.1 | ColumnnodeConnectivityIndex | read-only | mandatory | Node Connectivity table index. |
| 1.3.6.1.4.1.2.3.51.2.22.37.31.1.2 | ColumnnodeConnectivityName | read-only | mandatory | The name of the node as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.37.31.1.3 | ColumnnodeConnectivityStatus | read-only | mandatory | Indicates the communication status of the node. |
| 1.3.6.1.4.1.2.3.51.2.22.38 | NodecomponentServiceReset | |||
| 1.3.6.1.4.1.2.3.51.2.22.38.1 | TablecomponentServiceResetTable | not-accessible | mandatory | A table providing aux power status and the ability to perform a virtual reseat or hard restart of a component. |
| 1.3.6.1.4.1.2.3.51.2.22.38.1.1 | RowcomponentServiceResetEntry | not-accessible | mandatory | Component module power service reset entry |
| 1.3.6.1.4.1.2.3.51.2.22.38.1.1.1 | ColumncomponentServiceResetTopologyPath | read-only | mandatory | The unique identifier for a row in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree… |
| 1.3.6.1.4.1.2.3.51.2.22.38.1.1.2 | ColumncomponentServiceResetName | read-only | mandatory | A short text string describing the particular component. For the MM and blades, this name will be the configured name or its serial number if no user configure… |
| 1.3.6.1.4.1.2.3.51.2.22.38.1.1.3 | ColumncomponentServiceResetStatus | read-only | mandatory | Status of the aux power. A value of auxPowerOff(0) indicates that the componant aux power is off. A value of auxPowerOn(1) indicates that the componant aux pow… |
| 1.3.6.1.4.1.2.3.51.2.22.38.1.1.4 | ColumncomponentServiceResetCmd | read-write | mandatory | NOTE: Do not perform this service reset operation on a node that is currently in a maintenance mode state. See componentStatusHealthState in componentSystemSta… |
| 1.3.6.1.4.1.2.3.51.2.22.38.2 | ScalarcomponentServiceResetTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentServiceResetTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.39 | NodecomponentLEDs | |||
| 1.3.6.1.4.1.2.3.51.2.22.39.1 | TablecomponentLEDsTable | not-accessible | mandatory | Table of component LED information. NOTE: Querying objects in this table may take significantly longer than normal, so it is recommended that the query timeout… |
| 1.3.6.1.4.1.2.3.51.2.22.39.1.1 | RowcomponentLEDsEntry | not-accessible | mandatory | Component LEDs information entry |
| 1.3.6.1.4.1.2.3.51.2.22.39.1.1.1 | ColumnledComponentTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.22.39.1.1.2 | ColumnledComponentName | read-only | mandatory | The name of the component as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.22.39.1.1.3 | ColumnledComponentFault | read-only | mandatory | Indicates whether the component fault LED is on or off. |
| 1.3.6.1.4.1.2.3.51.2.22.39.1.1.4 | ColumnledComponentCheckLog | read-write | mandatory | Indicates whether the component check log information LED is on or off. For Write access, the LED can be turned off only. |
| 1.3.6.1.4.1.2.3.51.2.22.39.1.1.5 | ColumnledComponentIdentity | read-write | mandatory | Indicates whether the component identify LED is on, off, or blinking. |
| 1.3.6.1.4.1.2.3.51.2.22.39.2 | ScalarcomponentLEDsTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentLEDsTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.39.9 | TablecomponentLEDsDetailsTable | not-accessible | mandatory | Table of LED info for each component. |
| 1.3.6.1.4.1.2.3.51.2.22.39.9.1 | RowcomponentLEDsDetailsEntry | not-accessible | mandatory | Component LED info table entry |
| 1.3.6.1.4.1.2.3.51.2.22.39.9.1.1 | ColumncomponentLEDsDetailsTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.22.39.9.1.2 | ColumncomponentLEDsDetailsIndex | read-only | mandatory | Each component may have one or more LEDs and data associated with it, and this index object identifies the particular instance. |
| 1.3.6.1.4.1.2.3.51.2.22.39.9.1.3 | ColumncomponentLEDsDetailsComponentType | read-only | mandatory | The type of the component/subcomponent grouping for this LED. |
| 1.3.6.1.4.1.2.3.51.2.22.39.9.1.4 | ColumncomponentLEDsDetailsLabel | read-only | mandatory | The text description of the LED. |
| 1.3.6.1.4.1.2.3.51.2.22.39.9.1.5 | ColumncomponentLEDsDetailsState | read-only | mandatory | The current state of the LED. |
| 1.3.6.1.4.1.2.3.51.2.22.39.9.1.6 | ColumncomponentLEDsDetailsLocation | read-only | mandatory | The physical location of this LED on the hardware. |
| 1.3.6.1.4.1.2.3.51.2.22.39.10 | ScalarcomponentLEDsDetailsTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentLEDsDetailsTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.22.42 | NodebackupRestore | |||
| 1.3.6.1.4.1.2.3.51.2.22.42.1 | ScalarbackupRestoreAction | read-write | mandatory | Starts the backup or restore operation. It is intended to be write-only. NOTE: This function is only available for SNMPv3. |
| 1.3.6.1.4.1.2.3.51.2.22.42.2 | ScalarbackupRestoreStatus | read-only | mandatory | Get the status of the last backup/restore action which was initiated through SNMP. NOTE: This function is only available for SNMPv3. |
| 1.3.6.1.4.1.2.3.51.2.22.42.3 | ScalarbackupRestoreMessage | read-only | mandatory | Get the status message of the last backup/restore action which was initiated through SNMP. NOTE: This function is only available for SNMPv3. |
| 1.3.6.1.4.1.2.3.51.2.22.42.4 | ScalarbackupRestoreURI | read-write | mandatory | Contains the fully qualified remote location of the file. A fully qualified remote location contains a supported protocol followed by a colon and two slashes (… |
| 1.3.6.1.4.1.2.3.51.2.22.42.5 | ScalarbackupRestorePassword | read-write | mandatory | Password used for the encryption/decryption of the sensitive data in the backup file. It is intended to be write-only. NOTE: This function is only available fo… |
| 1.3.6.1.4.1.2.3.51.2.22.42.6 | ScalarbackupRestoreLogURI | read-write | mandatory | Indicates the URI address where the log file will be put. It will be used only if the backupRestoreLogPush will be set on push. Contains the fully qualified re… |
| 1.3.6.1.4.1.2.3.51.2.22.42.7 | ScalarbackupRestoreLogPush | read-write | mandatory | Causes the restore operation to push the log to the URI address. NOTE: This can be used when restoring without restarting. NOTE: This function is only availabl… |
| 1.3.6.1.4.1.2.3.51.2.23 | Nodeservice | |||
| 1.3.6.1.4.1.2.3.51.2.23.3 | NodebladeServiceData | |||
| 1.3.6.1.4.1.2.3.51.2.23.3.1 | TablebladeServiceDataTable | not-accessible | mandatory | Table of blade service data information. |
| 1.3.6.1.4.1.2.3.51.2.23.3.1.1 | RowbladeServiceDataEntry | not-accessible | mandatory | Blade service data entry |
| 1.3.6.1.4.1.2.3.51.2.23.3.1.1.1 | ColumnserviceDataIndex | read-only | mandatory | Blade service date index. |
| 1.3.6.1.4.1.2.3.51.2.23.3.1.1.2 | ColumnserviceDataBladeId | read-only | mandatory | The numeric blade ID. |
| 1.3.6.1.4.1.2.3.51.2.23.3.1.1.3 | ColumnserviceDataBladeExists | read-only | mandatory | Indicates whether the blade specified exists or not. |
| 1.3.6.1.4.1.2.3.51.2.23.3.1.1.4 | ColumnserviceDataBladePowerState | read-only | mandatory | Indicates whether the blade specified is powered on or not. If the MM is experiencing a communication problem with the blade, the state may be returned as unkn… |
| 1.3.6.1.4.1.2.3.51.2.23.3.1.1.5 | ColumnserviceDataBladeName | read-only | mandatory | The name of the blade as a string. |
| 1.3.6.1.4.1.2.3.51.2.23.3.1.1.7 | ColumnserviceDataDumpInitiate | read-write | mandatory | Initiates a type of dump collection to be initiated for the blade. NOTE: Not all blades support this, please check serviceDataDumpCapabilityMask OID to see if … |
| 1.3.6.1.4.1.2.3.51.2.23.3.1.1.8 | ColumnserviceDataDumpRetrieve | read-write | mandatory | Retrieve a type of service data file from blade to MM. NOTE: This OID only is valid for the last four bit mask designations listed in the serviceDataDumpCapabi… |
| 1.3.6.1.4.1.2.3.51.2.23.3.1.1.9 | ColumnserviceDataDumpCapabilityMask | read-only | mandatory | Indicates whether the blade has the capability to trigger service data and if so, which operations are supported and whether the file can be transferred to the… |
| 1.3.6.1.4.1.2.3.51.2.23.3.1.1.10 | ColumnserviceDataDumpInProgress | read-only | mandatory | An indicator as to whether a blade dump is in progress for the specified blade. This object ONLY applies to dumps that can be triggered by the MM and where the… |
| 1.3.6.1.4.1.2.3.51.2.23.4 | NodeserviceAdvisor | |||
| 1.3.6.1.4.1.2.3.51.2.23.4.1 | NodeautoCallHomeSetup | |||
| 1.3.6.1.4.1.2.3.51.2.23.4.1.1 | ScalaracceptLicenseAgreement | read-write | mandatory | Accept Terms and Conditions of MM Service Advisor. The user will have to accept the terms and conditions before Service Advisor can send diagnostic data to IBM… |
| 1.3.6.1.4.1.2.3.51.2.23.4.1.2 | ScalarserviceAdvisorEnable | read-write | mandatory | Disable/Enable IBM Support. The User Agreement must be accepted and the contact information must be set before the IBM Support function of Service Advisor can … |
| 1.3.6.1.4.1.2.3.51.2.23.4.2 | NodeserviceSupportCenter | |||
| 1.3.6.1.4.1.2.3.51.2.23.4.2.1 | ScalaribmSupportCenter | read-write | mandatory | The country code for the IBM Support Center. 2 character ISO country code. |
| 1.3.6.1.4.1.2.3.51.2.23.4.3 | NodecontactInformation | |||
| 1.3.6.1.4.1.2.3.51.2.23.4.3.1 | ScalarcompanyName | read-write | mandatory | The organization/company name of the contact person. 1-30 characters. |
| 1.3.6.1.4.1.2.3.51.2.23.4.3.2 | ScalarcontactName | read-write | mandatory | The name of the contact person.1-30 characters. |
| 1.3.6.1.4.1.2.3.51.2.23.4.3.3 | ScalarphoneNumber | read-write | mandatory | The phone of the contact person. 5-30 characters. |
| 1.3.6.1.4.1.2.3.51.2.23.4.3.4 | ScalaremailAddress | read-write | mandatory | The email of the contact person. It must contain '@' and dot '.' in form userid@hostname (130 characters maximum). The userid can be alphanumeric characters, '… |
| 1.3.6.1.4.1.2.3.51.2.23.4.3.5 | Scalaraddress | read-write | mandatory | The address of the machine location. The information in this field should be of sufficient detail to allow someone to quickly find the chassis when necessary. … |
| 1.3.6.1.4.1.2.3.51.2.23.4.3.6 | Scalarcity | read-write | mandatory | The city of the machine location. 1-30 characters. |
| 1.3.6.1.4.1.2.3.51.2.23.4.3.7 | Scalarstate | read-write | mandatory | The state of the machine location. 2-3 characters. |
| 1.3.6.1.4.1.2.3.51.2.23.4.3.8 | ScalarpostalCode | read-write | mandatory | The postal code of the location for this system. 1-9 characters, only alphanumeric characters are valid. |
| 1.3.6.1.4.1.2.3.51.2.23.4.3.9 | ScalarphoneNumberExt | read-write | mandatory | The phone number extension of the contact person. 1-30 characters. |
| 1.3.6.1.4.1.2.3.51.2.23.4.3.10 | ScalaraltContactName | read-write | mandatory | The name of the alternate contact person.1-30 characters. |
| 1.3.6.1.4.1.2.3.51.2.23.4.3.11 | ScalaraltPhoneNumber | read-write | mandatory | The phone of the alternate contact person. 5-30 characters. |
| 1.3.6.1.4.1.2.3.51.2.23.4.3.12 | ScalaraltPhoneNumberExt | read-write | mandatory | The phone number extension of the alternate contact person. 1-30 characters. |
| 1.3.6.1.4.1.2.3.51.2.23.4.3.13 | ScalaraltEmailAddress | read-write | mandatory | The email of the alternate contact person. It must contain '@' and dot '.' in form userid@hostname (130 characters maximum). The userid can be alphanumeric cha… |
| 1.3.6.1.4.1.2.3.51.2.23.4.4 | NodehttpProxyConfig | |||
| 1.3.6.1.4.1.2.3.51.2.23.4.4.1 | ScalarhttpProxyEnable | read-write | mandatory | Disable/Enable of the HTTP Proxy. Select Enable to use the proxy for call home connections from the MM to IBM. HTTP Proxy is used by the MM when it is not conn… |
| 1.3.6.1.4.1.2.3.51.2.23.4.4.2 | ScalarhttpProxyLocation | read-write | mandatory | Fully qualified host name or IP address of the HTTP Proxy. Maximum of 63 characters. |
| 1.3.6.1.4.1.2.3.51.2.23.4.4.3 | ScalarhttpProxyPort | read-write | mandatory | The port number of the HTTP Proxy. An integer value from 1 to 65535. |
| 1.3.6.1.4.1.2.3.51.2.23.4.4.4 | ScalarhttpProxyUserName | read-write | mandatory | User Name of the HTTP Proxy. A maximum of 30 characters string without spaces. |
| 1.3.6.1.4.1.2.3.51.2.23.4.4.5 | ScalarhttpProxyPassword | read-write | mandatory | Password of the HTTP Proxy. A maximum of 15 characters string without spaces. |
| 1.3.6.1.4.1.2.3.51.2.23.4.5 | NodeactivityLogs | |||
| 1.3.6.1.4.1.2.3.51.2.23.4.5.1 | TableactivityLogTable | not-accessible | mandatory | Table of Service Advisor Activity Log entries information. This table displays the last five events that were generated by the system or user that are called h… |
| 1.3.6.1.4.1.2.3.51.2.23.4.5.1.1 | RowactivityLogEntry | not-accessible | mandatory | Activity Log table entry. Each entry has the result of the FTP/TFTP Server attempt, the event ID, event source, date and time that event occured, and a text me… |
| 1.3.6.1.4.1.2.3.51.2.23.4.5.1.1.1 | ColumnactivityLogIndex | read-only | mandatory | The Activity Log index number. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.23.4.5.1.1.2 | ColumnactivityLogString | read-only | mandatory | A string of data detailing one Activity Log entry. The text message is from the original entry in the event log. For consistent results, view as a table and no… |
| 1.3.6.1.4.1.2.3.51.2.23.4.5.1.1.3 | ColumnactivityLogAcknowledge | read-write | mandatory | The acknowledgement of one Activity Log entry as corrected. This field allows the users to set a reminder next to certain events to indicate their awareness of… |
| 1.3.6.1.4.1.2.3.51.2.23.4.5.1.1.4 | ColumnactivityLogAttribute | read-only | mandatory | A string of data detailing one Activity Log entry's attribute. Status PENDING indicates that the system is preparing for the event to be called home by collect… |
| 1.3.6.1.4.1.2.3.51.2.23.5 | NodeautoFTPSetup | |||
| 1.3.6.1.4.1.2.3.51.2.23.5.1 | ScalarautoFTPCallMode | read-write | mandatory | This field specifies the automated problem reporting mode. Automated problem reporting mode allows the MM to automatically put service data to a specified serv… |
| 1.3.6.1.4.1.2.3.51.2.23.5.2 | ScalarautoFTPCallAddr | read-write | mandatory | This field specifies the remote server address of FTP and TFTP. It should be fully qualified hostname or IP address. |
| 1.3.6.1.4.1.2.3.51.2.23.5.3 | ScalarautoFTPCallPort | read-write | mandatory | This field specifies the port on remote FTP/TFTP server for data transmission. |
| 1.3.6.1.4.1.2.3.51.2.23.5.4 | ScalarautoFTPCallUserID | read-write | mandatory | This field specifies the user account to login remote FTP server. |
| 1.3.6.1.4.1.2.3.51.2.23.5.5 | ScalarautoFTPCallPassword | read-write | mandatory | This field specifies the password to login remote FTP server. |
| 1.3.6.1.4.1.2.3.51.2.23.6 | NodecallHomeExclusionEvents | |||
| 1.3.6.1.4.1.2.3.51.2.23.6.1 | TablereadCallHomeExclusionEventTable | not-accessible | mandatory | Table of Call Home Exclusion Event entries information. |
| 1.3.6.1.4.1.2.3.51.2.23.6.1.1 | RowreadCallHomeExclusionEventEntry | not-accessible | mandatory | Call Home Exclusion Event table entry |
| 1.3.6.1.4.1.2.3.51.2.23.6.1.1.1 | ColumnreadCallHomeExclusionEventIndex | read-only | mandatory | The index number of one Call Home Exclusion Event. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.23.6.1.1.2 | ColumnreadCallHomeExclusionEventID | read-only | mandatory | The Event ID of one Call Home Exclusion Event entry. For consistent results, view as a table and not as individual entries. |
| 1.3.6.1.4.1.2.3.51.2.23.6.2 | ScalaraddCallHomeExclusionEvent | read-write | mandatory | Add one call home Event ID into the Call Home Exclusion List. The Event ID is an 8-digit hexadecimal number (0-F) with an optional prefix of '0x' or '0X'. An E… |
| 1.3.6.1.4.1.2.3.51.2.23.6.3 | ScalarrmCallHomeExclusionEvent | read-write | mandatory | Remove one call home Event ID from the Call Home Exclusion List. The Event ID is an 8-digit hexadecimal number (0-F) with an optional prefix of '0x' or '0X'. A… |
| 1.3.6.1.4.1.2.3.51.2.23.6.4 | ScalarrmAllCallHomeExclusionEvent | read-write | mandatory | Remove all Event IDs from the Call Home Exclusion List. Events on the exclusion list can not be removed if autoFtpMode is disabled. If Service Advisor Terms an… |
| 1.3.6.1.4.1.2.3.51.2.23.10 | NodecomponentPowerServiceReset | |||
| 1.3.6.1.4.1.2.3.51.2.23.10.1 | TablebladePowerServiceResetTable | not-accessible | mandatory | A table providing aux power status and the ability to perform a virtual reseat or hard restart of a blade. |
| 1.3.6.1.4.1.2.3.51.2.23.10.1.1 | RowbladePowerServiceResetEntry | not-accessible | mandatory | Blade power service reset entry |
| 1.3.6.1.4.1.2.3.51.2.23.10.1.1.1 | ColumnbladePowerServiceResetIndex | read-only | mandatory | Blade power service reset index. |
| 1.3.6.1.4.1.2.3.51.2.23.10.1.1.2 | ColumnbladePowerServiceResetBladeId | read-only | mandatory | The numeric blade slot number. |
| 1.3.6.1.4.1.2.3.51.2.23.10.1.1.3 | ColumnbladePowerServiceResetStatus | read-only | mandatory | Status of the aux power. A value of auxPowerOff(0) indicates that the blade aux power is off. A value of auxPowerOn(1) indicates that the blade aux power is on. |
| 1.3.6.1.4.1.2.3.51.2.23.10.1.1.4 | ColumnbladePowerServiceResetCmd | read-write | mandatory | NOTE: Do not perform this service reset operation on a node that is currently in a maintenance mode state. See bladeHealthState in bladeSystemStatusTable for m… |
| 1.3.6.1.4.1.2.3.51.2.23.10.2 | TablesmPowerServiceResetTable | not-accessible | mandatory | A table providing aux power status and the ability to perform a virtual reseat or hard restart of a switch. |
| 1.3.6.1.4.1.2.3.51.2.23.10.2.1 | RowsmPowerServiceResetEntry | not-accessible | mandatory | Switch module power service reset entry |
| 1.3.6.1.4.1.2.3.51.2.23.10.2.1.1 | ColumnsmPowerServiceResetIndex | read-only | mandatory | Switch module power service reset index. |
| 1.3.6.1.4.1.2.3.51.2.23.10.2.1.2 | ColumnsmPowerServiceResetSwitchId | read-only | mandatory | The switch module numeric identifier. |
| 1.3.6.1.4.1.2.3.51.2.23.10.2.1.3 | ColumnsmPowerServiceResetStatus | read-only | mandatory | Status of the aux power power. A value of auxPowerOff(0) indicates that the switch aux power is off. A value of auxPowerOn(1) indicates that the switch aux pow… |
| 1.3.6.1.4.1.2.3.51.2.23.10.2.1.4 | ColumnsmPowerServiceResetCmd | read-write | mandatory | To reset the auxiliary power on a switch component, set this object to resetVirtualReseatOperation(1). This will toggle the auxiliary power to the switch and s… |
| 1.3.6.1.4.1.2.3.51.2.23.15 | NodecomponentServiceData | |||
| 1.3.6.1.4.1.2.3.51.2.23.15.1 | TablecomponentServiceDataTable | not-accessible | mandatory | Table of component service data information. |
| 1.3.6.1.4.1.2.3.51.2.23.15.1.1 | RowcomponentServiceDataEntry | not-accessible | mandatory | Component service data entry |
| 1.3.6.1.4.1.2.3.51.2.23.15.1.1.1 | ColumncomponentServiceDataTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.23.15.1.1.2 | ColumncomponentServiceDataComponentName | read-only | mandatory | The name of the component as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.23.15.1.1.3 | ColumncomponentServiceDataDumpInitiate | read-write | mandatory | Initiates a type of dump collection to be initiated for the component and sent to the MM. NOTE: Not all components support this, please check componentServiceD… |
| 1.3.6.1.4.1.2.3.51.2.23.15.1.1.4 | ColumncomponentServiceDataDumpRetrieve | read-write | mandatory | Retrieve a type of service data file from component to MM. NOTE: This OID only is valid for the last four bit mask designations listed in the componentServiceD… |
| 1.3.6.1.4.1.2.3.51.2.23.15.1.1.5 | ColumncomponentServiceDataDumpCapabilityMask | read-only | mandatory | Indicates whether the component has the capability to trigger service data and if so, which operations are supported and whether the file can be transferred to… |
| 1.3.6.1.4.1.2.3.51.2.23.15.1.1.6 | ColumncomponentServiceDataDumpInProgress | read-only | mandatory | An indicator as to whether a component dump is in progress for the specified component. This object ONLY applies to dumps that can be triggered by the MM and w… |
| 1.3.6.1.4.1.2.3.51.2.23.15.1.1.7 | ColumncomponentServiceDataStatus | read-only | mandatory | A status indicator for dump progress. This object ONLY applies to switch modules dumps. |
| 1.3.6.1.4.1.2.3.51.2.23.15.1.1.8 | ColumncomponentServiceDataStatusDetails | read-only | mandatory | The failure status as a null terminated string. This object ONLY applies to switch modules dumps. |
| 1.3.6.1.4.1.2.3.51.2.23.15.2 | ScalarcomponentServiceDataTableCacheTimeout | read-only | mandatory | The timeout value (in seconds) of the cached data for the table, componentServiceDataTable. This value is static (constant) and cannot be set. |
| 1.3.6.1.4.1.2.3.51.2.23.21 | NodedownloadMMServiceData | |||
| 1.3.6.1.4.1.2.3.51.2.23.21.1 | ScalardownloadMMServiceDataFileCreateAndDownload | read-write | mandatory | Specifying this string initiates the generation of the FFDC (First-Failure Data Capture) data collection (compressed group of files) for the CMM and the downlo… |
| 1.3.6.1.4.1.2.3.51.2.23.21.2 | ScalardownloadMMServiceDataStatus | read-only | mandatory | An indicator as to whether the FFDC generation and download is in progress. To initiate this process, set the object, downloadMMServiceDataFileCreateAndDownloa… |
| 1.3.6.1.4.1.2.3.51.2.23.21.3 | ScalardownloadMMServiceDataResult | read-write | mandatory | An indicator as to whether the FFDC generation and download was successful. The FFDC generation and download is started by setting a destination filename with … |
| 1.3.6.1.4.1.2.3.51.2.23.21.4 | ScalardownloadMMServiceDataCancelDownload | read-write | mandatory | Set this object to 'cancel(1)' to stop the FFDC file download process. 'cancel(1)' is the only valid value that may be set. The value of this object will be 'c… |
| 1.3.6.1.4.1.2.3.51.2.24 | Nodescaling | |||
| 1.3.6.1.4.1.2.3.51.2.24.1 | TablescalableComplexTable | not-accessible | mandatory | Table of scalable complex information. This table provides information related to the scalable complexes installed in the chassis. |
| 1.3.6.1.4.1.2.3.51.2.24.1.1 | RowscalableComplexEntry | not-accessible | mandatory | Scalable complex information. |
| 1.3.6.1.4.1.2.3.51.2.24.1.1.1 | ColumnscalableComplexTopologyPath | read-only | mandatory | The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in th… |
| 1.3.6.1.4.1.2.3.51.2.24.1.1.2 | ColumnscalableComplexIdentifier | read-only | mandatory | The unique numeric identifier for a complex installed in the chassis. |
| 1.3.6.1.4.1.2.3.51.2.24.1.1.3 | ColumnscalableComplexNodeName | read-only | mandatory | The name of the node as a null terminated string. |
| 1.3.6.1.4.1.2.3.51.2.24.1.1.4 | ColumnscalableComplexNodeHealthState | read-only | mandatory | The system health state for the component. Unknown: Component is in an undefined state. Good: Component is operating normally. Warning: One or more outstanding… |
| 1.3.6.1.4.1.2.3.51.2.24.1.1.5 | ColumnscalableComplexNodePowerState | read-only | mandatory | Indicates the power state of the node. |
| 1.3.6.1.4.1.2.3.51.2.24.1.1.6 | ColumnscalableComplexNodeResources | read-only | mandatory | A string providing a summary overview of the resources provided by this node. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| InetAddressIPv6 | OCTET STRING (SIZE (16)) EntryStatus ::= INTEGER { valid(1), createRequest(2), underCreation(3), invalid(4) } | current | Represents an IPv6 network address. Since MIB browsers may require different formats, the address is expected to be the 16 byte address in network-byte order, and shortened formats such as 0::0 are not accepted in SET o… |