CONFIG-MIB
246 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.11.2.14.11.5.1.7 | NodehpConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1 | NodehpSwitchConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.0 | NodehpSwitchTraps | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.0.1 | NodehpSwitchStpErrantBpduReceived | This trap indicates that unexpected (errant) STP BPDU has been received on a port (e.g. on a port that is connected to non-STP device). This notification trap … | ||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.0.1 | NodehpSwitchTrapsObjects | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.0.1.1 | ScalarhpSwitchStpErrantBpduDetector | accessible-for-notify | optional | The identifier of the feature generating Errant BPDU trap. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.0.1.2 | ScalarhpSwitchStpErrantBpduSrcMac | accessible-for-notify | optional | The source MAC address of the port sending Errant STP BPDU. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1 | NodehpSwitchSystemConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.1 | ScalarhpSwitchAutoReboot | read-write | mandatory | If the value of this variable was set to yes(1), booting will conditionally enable all application modules-the spanning tree, IP and IPX etc.. Otherwise every … |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.2 | ScalarhpSwitchTimeZone | read-write | mandatory | The number of minutes to the east of Greenwich Mean Time(GMT). For a location west of GMT, use a negative integer. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.3 | ScalarhpSwitchDaylightTimeRule | read-write | mandatory | The daylight savings time rule for use by the Internet's RFC 868 Time protocol. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.4 | ScalarhpSwitchDaylightBeginningMonth | read-write | mandatory | The month that daylight saving time starts if DaylightTimeRule is set to userDefined. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.5 | ScalarhpSwitchDaylightBeginningDay | read-write | mandatory | The day of the month that daylight saving time starts if DaylightTimeRule is set to userDefined. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.6 | ScalarhpSwitchDaylightEndingMonth | read-write | mandatory | The month that daylight saving time ends if DaylightTimeRule is set to userDefined. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.7 | ScalarhpSwitchDaylightEndingDay | read-write | mandatory | The day of the month that daylight saving time emds if DaylightTimeRule is set to userDefined. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.8 | ScalarhpSwitchSystemConfigStatus | read-only | mandatory | The configuration status of this group of objects. If one or more variables in this group were reconfigurated since last reboot and required reboot to take eff… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.9 | ScalarhpSwitchSystemPortLEDMode | read-write | mandatory | The mode of the port LED can be either link/activity (link for 3 seconds then activity thereafter) or link-only. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.10 | ScalarhpSwitchControlUnknownIPMulticast | read-write | mandatory | When enabled along with IGMP, any IP Multicast packets that are not already controlled by IGMP will be restricted to ports that have detected a multicast route… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.11 | ScalarhpSwitchIgmpDelayedGroupFlushTimer | read-write | mandatory | This feature is disabled by default, which is indicated by a timer value of 0 seconds. When IGMP is enabled and the value of the Delayed Group Flush Timer is n… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.12 | ScalarhpSwitchMaxFrameSize | read-write | mandatory | This is the value of the global jumbos max-frame-size supported by the switch. The default value for this is set to 9216, in order to make it compatible with p… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.1.13 | ScalarhpSwitchIpMTU | read-write | mandatory | This is the value of the global jumbos IP MTU or L3 MTU supported by the switch. The default value for this is set to 9198, in order to make it compatible with… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.2 | NodehpSwitchConsoleConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.2.1 | ScalarhpSwitchTelnetAdminStatus | read-write | obsolete | The status of the console telnet operation. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.2.2 | ScalarhpSwitchTerminalType | read-write | mandatory | Terminal type of the console device. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.2.3 | ScalarhpSwitchConsoleRefRate | read-write | mandatory | The rate, in second per cycle, at which the display of various switch measurements. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.2.4 | ScalarhpSwitchDisplayedEvent | read-write | mandatory | The type of event messages are automatically displayed on the console. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.2.5 | ScalarhpSwitchConsoleConfigStatus | read-only | mandatory | The configuration status of this group of objects. If one or more variables in this group were reconfigurated since last reboot and required reboot to take eff… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3 | NodehpSwitchPortConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1 | TablehpSwitchPortTable | not-accessible | mandatory | A table that contains information about the current port status in this device. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1 | RowhpSwitchPortEntry | not-accessible | mandatory | Information about a specific port status in this device. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.1 | ColumnhpSwitchPortIndex | read-only | mandatory | The ifIndex value which uniquely identifies a row in the Interfaces Table. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.2 | ColumnhpSwitchPortType | read-only | mandatory | The type of port. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.3 | ColumnhpSwitchPortDescr | read-only | mandatory | A textual string containing information about the interface. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.4 | ColumnhpSwitchPortAdminStatus | read-write | obsolete | The desired state of the interface. This variable is similar to the ifAdminStatus but instead of keeping the operational status, this variable maintain the des… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.5 | ColumnhpSwitchPortEtherMode | read-write | mandatory | The type of transmission on this port. This variable is valid only if the hpSwitchPortType was Ethernet. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.6 | ColumnhpSwitchPortVgMode | read-write | mandatory | The type of transmission on this port. This variable is valid only if the hpSwitchPortType was VG. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.7 | ColumnhpSwitchPortLinkbeat | read-write | mandatory | The linkbeat status of this port. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.8 | ColumnhpSwitchPortTrunkGroup | read-write | mandatory | The trunk group this port belong to. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.9 | ColumnhpSwitchPortBcastLimit | read-write | mandatory | The percentage of network bandwidth consumed by broadcast traffic through this port. If the value of this variable is 0, there will be no broadcast limit. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.10 | ColumnhpSwitchPortFastEtherMode | read-write | mandatory | The type of transmission on this port. This variable is valid only if the hpSwitchPortType was Fast Ethernet. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.11 | ColumnhpSwitchPortFlowControl | read-write | mandatory | The Flow Control of this port. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.13 | ColumnhpSwitchPortTrunkType | read-write | mandatory | Used in conjunction with hpSwitchPortTrunkGroup to determine what type of trunk and which group it belongs to. If hpSwitchPortTrunkGroup is set to 0, trunking … |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.14 | ColumnhpSwitchPortTrunkLACPStatus | read-write | mandatory | Used in conjunction with hpSwitchPortTrunkType. When the trunk is a LACP trunk, this variable defines its administrative status |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.15 | ColumnhpSwitchPortMDIXStatus | read-only | mandatory | Shows the MDI/MDIX setting for an RJ-45 port. Returns a value of 'not-applicable' for all ports except RJ-45 ports. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.1.1.16 | ColumnhpSwitchPortAutoMDIX | read-write | mandatory | Sets the MDI/MDIX value for an RJ-45 port. Negates need for crossover cables. 'automdix', 'mdi', or 'mdix' may be set when the port configuration is set to any… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.3.2 | ScalarhpSwitchPortConfigStatus | read-only | mandatory | The configuration status of this group of objects. If one or more variables in this group were reconfigured since last reboot and required reboot to take effec… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.4 | NodehpSwitchIpxConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.4.2 | ScalarhpSwitchIpxConfigStatus | read-only | mandatory | The status of the IPX configuration table. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.5 | NodehpSwitchIpConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.5.1 | ScalarhpSwitchIpTimepAdminStatus | read-write | mandatory | The operational status of the Time protocol. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.5.2 | ScalarhpSwitchIpTimepServerAddr | read-write | deprecated | ### deprecated ### The IP address of the Time server. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.5.3 | ScalarhpSwitchIpTimepPollInterval | read-write | mandatory | The client poll interval of the Time server in minutes. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.5.5 | ScalarhpSwitchIpConfigStatus | read-only | obsolete | The configuration status of the Timep and IP related objects. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.5.6 | ScalarhpSwitchIpTftpMode | read-write | mandatory | The operational mode of the Tftp protocol. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.5.7 | ScalarhpSwitchIpTimepInetServerAddrType | read-write | mandatory | The IP address type of the Time server. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.5.8 | ScalarhpSwitchIpTimepInetServerAddr | read-write | mandatory | The IP address (of the Time server)to which this entry's addressing information pertains. hpSwitchIpTimepInetServerAddr is always interpreted within the contex… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6 | NodehpSwitchSerialLinkConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.1 | ScalarhpSwitchSLinkBaudRate | read-write | mandatory | The rate of data transfer between the console and the node. baudRate1 is speed sense. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.2 | ScalarhpSwitchSLinkFlowCtrl | read-write | mandatory | The flow-control mechanism between the console and the switch. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.3 | ScalarhpSwitchSLinkConnInactTime | read-write | mandatory | The number of minutes to wait after no character was input to log out the console. Valid values are 0 (not to log out of the console for inactivity) through 12… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.4 | ScalarhpSwitchSLinkModemConnTime | read-write | mandatory | The number of seconds to wait for data mode and clear to send and receiver ready signals after asserting request to send and terminal ready signals. Valid valu… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.5 | ScalarhpSwitchSLinkModemLostRecvTime | read-write | mandatory | The number of milliseconds the receiver ready signal is allowed to drop before the switch will disconnect the modem. Valid values are 0 (the switch will wait f… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.6 | ScalarhpSwitchSLinkModemDisConnTime | read-write | mandatory | The number of seconds to wait after the modem is disconnected before allowing the modem to be reconnected. Valid values are 0 (allow a connection as soon as po… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.7 | ScalarhpSwitchSLinkParity | read-only | mandatory | The type of parity to use between the console and the node. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.8 | ScalarhpSwitchSLinkCharBits | read-only | mandatory | The number of bits per character to use between the console and the node. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.9 | ScalarhpSwitchSLinkStopBits | read-only | mandatory | The number of stop bots to use when communicating between the console and the node. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.10 | ScalarhpSwitchSLinkConfigStatus | read-only | mandatory | The configuration status of this group of objects. If one or more variables in this group were reconfigured since last reboot and required reboot to take effec… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8 | NodehpSwitchFilterConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.1 | TablehpSwitchFilterConfigTable | not-accessible | mandatory | A table that contains information about the traffic filter configuration in this device. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.1.1 | RowhpSwitchFilterConfigEntry | not-accessible | mandatory | Information about a traffic filter configuration in this device. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.1.1.1 | ColumnhpSwitchFilterIndex | read-only | mandatory | An index that uniquely identifies a traffic filter for which this entry contains information. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.1.1.2 | ColumnhpSwitchFilterType | read-write | mandatory | The type of filter. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.1.1.3 | ColumnhpSwitchFilterSrcPort | read-write | mandatory | This variable is required when a port filter or unicast filter was configurated. It will be ignored otherwise. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.1.1.4 | ColumnhpSwitchFilterMacAddr | read-write | mandatory | This variable is valid only if a unicast or multicast filter was defined. It will be ignored otherwise. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.1.1.5 | ColumnhpSwitchFilterProtocolType | read-write | mandatory | This variable is valid only if a level-3 filter was defined. It will be ignored otherwise. This variable will contain either a etherType (DIX Ethernet) or SAP(… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.1.1.6 | ColumnhpSwitchFilterPortMask | read-write | mandatory | This variable specifies a group of ports whose traffic will be filtered. Each octet within the value of this object specifies a set of eight ports, with the fi… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.1.1.7 | ColumnhpSwitchFilterEntryStatus | read-write | mandatory | The status of a filter entry. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.9 | NodehpSwitchProbeConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.9.1 | ScalarhpSwitchProbeType | read-write | obsolete | If the value of this variable is equal to 1, the probe will monitor those ports specified by hpSwitchProbedPortMask, otherwise all of the port belong to the vi… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.9.2 | ScalarhpSwitchProbedVlanId | read-write | obsolete | The probed virtual LAN. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.9.3 | ScalarhpSwitchProbePort | read-write | obsolete | The port that every packet passes through those probed ports will be copied to. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.9.4 | ScalarhpSwitchProbeAdminStatus | read-write | obsolete | The operational status of the probing function |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.9.5 | ScalarhpSwitchProbedPortMask | read-write | obsolete | This variable specifies a group of ports which will be probed. Each octet within the value of this object specifies a set of eight ports, with the first octet … |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.11 | NodehpSwitchFddiIpFragConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.11.1 | TablehpSwitchFddiIpFragConfigTable | not-accessible | mandatory | A list of IP fragmentation configuration parameters for the FDDI cards in the switch. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.11.1.1 | RowhpSwitchFddiIpFragConfigEntry | not-accessible | mandatory | An Fddi IP fragmentation entry which is containing configurable options for the FDDI cards in the switch. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.11.1.1.1 | ColumnhpSwitchFddiIpFragConfigIndex | read-only | mandatory | A unique value for each FDDI Card. The value for each FDDI card must remain constant at least from one re-initialization of the entity's network management sys… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.11.1.1.2 | ColumnhpSwitchFddiIpFragConfigStatus | read-write | mandatory | The operational status of FDDI IP fragmentation for each FDDI card. enable(1): FDDI card will fragment all packets which are bigger then the Ethernet packet si… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.12 | NodehpSwitchABCConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.12.1 | TablehpSwitchABCConfigTable | not-accessible | mandatory | A list of Automatic Broadcast Control (ABC disable/enable entries for each VLAN on the switch. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.12.1.1 | RowhpSwitchABCConfigEntry | not-accessible | mandatory | Contains the ABC status for each VLAN on the switch, including IP RIP control and IPX RIP/SAP control. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.12.1.1.1 | ColumnhpSwitchABCConfigVlan | read-only | mandatory | The user is able to enable/disable ABC on a per VLAN basis, so the VLAN serves as an index into the ABC configuration table. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.12.1.1.2 | ColumnhpSwitchABCConfigControl | read-write | mandatory | ABC control is either IP&IPX or IP or IPX or disabled for each VLAN on the switch. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.12.1.1.3 | ColumnhpSwitchABCConfigIpRipControl | read-write | mandatory | IP RIP control. If this feature is enabled then IP RIP packets will only be forwarded on ports, within its VLAN domain, that have heard RIPs before. If this fe… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.12.1.1.4 | ColumnhpSwitchABCConfigIpxRipSapControl | read-write | mandatory | IPX RIP/SAP control. If this feature is enabled then IPX RIP/SAP packets will only be forwarded on ports, within its VLAN domain, that have previously seen RIP… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.12.1.1.5 | ColumnhpSwitchABCConfigVlanBcastLimit | read-write | mandatory | The percentage of network bandwidth consumed by broadcast traffic through VLAN. If the value of this variable is 0, there will be no broadcast limit. There is … |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.12.1.1.7 | ColumnhpSwitchABCConfigAutoGatewayConfig | read-write | mandatory | If this feature is enabled then DHCP packets both ucast and bcast with UDP destination port 68 will be intercepted. DHCP packets with the router option in the … |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14 | NodehpSwitchStpConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.1 | TablehpSwitchStpVlanTable | not-accessible | mandatory | A table that contains vlan-specific information for the Spanning Tree Protocol. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.1.1 | RowhpSwitchStpVlanEntry | not-accessible | mandatory | A list of information maintained by every port about the Spanning Tree Protocol state for that port. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.1.1.1 | ColumnhpSwitchStpVlan | read-only | mandatory | The operational status of the spanning tree protocol. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.1.1.2 | ColumnhpSwitchStpAdminStatus | read-write | mandatory | The operational status of the spanning tree protocol. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.1.1.3 | ColumnhpSwitchStpPriority | read-write | mandatory | The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID ar… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.1.1.4 | ColumnhpSwitchStpMaxAge | read-write | mandatory | The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is … |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.1.1.5 | ColumnhpSwitchStpHelloTime | read-write | mandatory | The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become … |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.1.1.6 | ColumnhpSwitchStpForwardDelay | read-write | mandatory | This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2 | TablehpSwitchStpPortTable | not-accessible | mandatory | A table that contains port-specific information for the Spanning Tree Protocol. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1 | RowhpSwitchStpPortEntry | not-accessible | mandatory | A list of information maintained by every port about the Spanning Tree Protocol state for that port. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.1 | ColumnhpSwitchStpPort | read-only | mandatory | The port number of the port for which this entry contains Spanning Tree Protocol management information. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.2 | ColumnhpSwitchStpPortType | read-only | mandatory | The type of port. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.3 | ColumnhpSwitchStpPortSrcMac | read-only | mandatory | The source MAC address used by the spanning tree protocol. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.4 | ColumnhpSwitchStpPortPriority | read-write | mandatory | The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is … |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.5 | ColumnhpSwitchStpPortPathCost | read-write | mandatory | The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value o… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.6 | ColumnhpSwitchStpPortMode | read-write | mandatory | If the value of this variable is set to fast(2), the port will go directly into the Forwarding State when a device is connected to it. Use this feature only on… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.7 | ColumnhpSwitchStpPortBpduFilter | read-write | optional | Setting True will cause port to ignore ingress BPDUs and not generate egress BPDUs, as the result the port will stay in forwarding state. Default is False. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.8 | ColumnhpSwitchStpPortBpduProtection | read-write | optional | Setting True indicates that no BPDUs are expected to be received on this port. At the reception of BPDUs the BPDU protection mechanism will disable this port a… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.9 | ColumnhpSwitchStpPortErrantBpduCounter | read-only | optional | Counts the number of BPDUs that were not expected to be received on this port. This counter gets incremented only if hpSwitchStpPortBpduProtection, hpSwitchStp… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.10 | ColumnhpSwitchStpPortPvstFilter | read-write | optional | Setting True will cause the port to ignore incoming PVST BPDUs. Default is False. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.2.1.11 | ColumnhpSwitchStpPortPvstProtection | read-write | optional | Setting True indicates that any PVST BPDUs arriving on this port should be discarded and that this will cause the port to be disabled. The port will remain dis… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.3 | ScalarhpSwitchStpTrapCntl | read-write | optional | Controls generation of SNMP traps by STP-enabled switch for events defined in this MIB. The set bit means 'enabled'. - errantBpdu(0) The state of this bit spec… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.14.4 | ScalarhpSwitchStpBpduProtectionTimeout | read-write | optional | The duration of time in seconds when a protected port affected by receiving of an unauthorized BPDU will remain in down state. The zero value means infinity. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15 | NodehpSwitchIgmpConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.1 | TablehpSwitchIgmpConfigTable | not-accessible | mandatory | A table that contains information about the IGMP Querier capacity or High Priority Forward configuration on any given vlan on the switch. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.1.1 | RowhpSwitchIgmpConfigEntry | not-accessible | mandatory | Information about the IGMP Querier feature associated with a specific virtal LAN in this device. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.1.1.1 | ColumnhpSwitchIgmpVlanIndex | read-only | mandatory | An index that uniquely identifies the IGMP configuration of a virtual LAN for which this entry contains information. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.1.1.2 | ColumnhpSwitchIgmpState | read-write | mandatory | The operational status of the IGMP support for this virtual LAN. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.1.1.3 | ColumnhpSwitchIgmpQuerierState | read-write | mandatory | The operational status of the IGMP Querier functionality for this virtual LAN. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.1.1.4 | ColumnhpSwitchIgmpPriorityState | read-write | mandatory | The operational status of the IGMP Forward with High Priority mode for this virtual LAN. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.1.1.5 | ColumnhpSwitchIgmpQuerierInterval | read-write | mandatory | The time (in seconds) to wait between Querier election cycles for this virtual LAN. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.2 | TablehpSwitchIgmpPortConfigTable | not-accessible | mandatory | A table that contains information about the IGMP port configurations on this switch. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.2.1 | RowhpSwitchIgmpPortConfigEntry | not-accessible | mandatory | The information associated with each IGMP port configuration. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.2.1.1 | ColumnhpSwitchIgmpPortIndex | read-only | mandatory | The ifIndex value which uniquely identifies a row in the Interfaces Table. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.2.1.2 | ColumnhpSwitchIgmpPortType | read-only | mandatory | The type of port. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.2.1.3 | ColumnhpSwitchIgmpIpMcastState | read-write | mandatory | The operational status of the IGMP feature for this port or trunk. 1 implies that all IP Multicast traffic will be monitored on the port, 2 implies that IP Mul… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.3 | TablehpSwitchIgmpPortConfigTable2 | not-accessible | mandatory | A table that contains information about the IGMP port configurations on this switch. This table supercedes hpSwitchIgmpPortConfigTable for products which suppo… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.3.1 | RowhpSwitchIgmpPortConfigEntry2 | not-accessible | mandatory | The information associated with each IGMP port configuration. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.3.1.1 | ColumnhpSwitchIgmpPortVlanIndex2 | read-only | mandatory | The Vlan Index value which uniquely identifies a row in the Interfaces Table. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.3.1.2 | ColumnhpSwitchIgmpPortIndex2 | read-only | mandatory | The ifIndex value which uniquely identifies a row in the Interfaces Table. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.3.1.3 | ColumnhpSwitchIgmpPortType2 | read-only | mandatory | The type of port. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.3.1.4 | ColumnhpSwitchIgmpIpMcastState2 | read-write | mandatory | The operational status of the IGMP feature for this port or trunk. 1 implies that all IP Multicast traffic will be monitored on the port, 2 implies that IP Mul… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.3.1.5 | ColumnhpSwitchIgmpPortForcedLeaveState | read-write | mandatory | The operational status of the IGMP feature for this port or trunk indicates whether any IGMP V2 Leaves received for an IP Multicast group will cause the group … |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.3.1.6 | ColumnhpSwitchIgmpPortFastLeaveState | read-write | mandatory | The operational status of the IGMP feature for this port or trunk indicates whether any IGMP V2 Leaves received for an IP Multicast group will cause the group … |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.4 | ScalarhpSwitchIgmpForcedLeaveInterval | read-write | mandatory | When a port's hpSwitchIgmpPortForcedLeaveState is enabled, this is the amount of time allowed for an IGMP V2 Report to arrive and cancel deletion of a multicas… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17 | NodehpSwitchCosConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.1 | TablehpSwitchCosPortConfigTable | not-accessible | mandatory | A table that contains information about the CoS port configurations on this switch. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.1.1 | RowhpSwitchCosPortConfigEntry | not-accessible | mandatory | The information associated with each CoS port configuration. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.1.1.1 | ColumnhpSwitchCosPortIndex | read-only | mandatory | The ifIndex value which uniquely identifies a row in the Interfaces Table. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.1.1.2 | ColumnhpSwitchCosPortType | read-only | deprecated | The type of port. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.1.1.3 | ColumnhpSwitchCosPortPriority | read-write | mandatory | The 802.1p priority value to assign to packets received on the specified port. This value will be inserted in the 802.1Q tag and the packet will be placed in t… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.1.1.4 | ColumnhpSwitchCosPortDSCPPolicy | read-write | mandatory | The DSCP Policy to assign to packets received on the specified Port. This is an index into the hpSwitchCosDSCPPolicy table, or the value 255 indicating no DSCP… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.1.1.5 | ColumnhpSwitchCosPortResolvedPriority | read-only | mandatory | The 802.1p priority that will be applied to packets received on the specified port. This value represents the actual operating value for this CoS port entry. A… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.1.1.6 | ColumnhpSwitchCosPortApplyPolicy | read-write | mandatory | This object determines which configuration policy, noPolicyOverride, hpSwitchCosPortPriority or hpSwitchCosPortDSCPPolicy, applies for the given Port CoS entry… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.2 | TablehpSwitchCosVlanConfigTable | not-accessible | mandatory | A table that contains information about the CoS Vlan configurations on this switch. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.2.1 | RowhpSwitchCosVlanConfigEntry | not-accessible | mandatory | The information associated with each CoS Vlan configuration. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.2.1.1 | ColumnhpSwitchCosVlanIndex | read-only | mandatory | The index that uniquely identifies the CoS configuration of a virtual LAN for which this entry contains information. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.2.1.2 | ColumnhpSwitchCosVlanPriority | read-write | mandatory | The 802.1p priority value to assign to packets received on the specified Vlan. This value will be inserted in the 802.1Q tag and the packet will be placed in t… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.2.1.3 | ColumnhpSwitchCosVlanDSCPPolicy | read-write | mandatory | The DSCP Policy to assign to packets received on the specified Vlan. This is an index into the hpSwitchCosDSCPPolicy table, or the value 255 indicating no DSCP… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.2.1.4 | ColumnhpSwitchCosVlanResolvedPriority | read-only | mandatory | The 802.1p priority that will be applied to packets received on the specified VLAN. This value represents the actual operating value for this CoS vlan entry. A… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.2.1.5 | ColumnhpSwitchCosVlanApplyPolicy | read-write | mandatory | This object determines which configuration policy, noPolicyOverride, hpSwitchCosVlanPriority or hpSwitchCosDSCPPolicy, applies for this given Vlan CoS entry. T… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.3 | TablehpSwitchCosProtocolConfigTable | not-accessible | mandatory | A table that contains information about the CoS protocol type configurations on this switch. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.3.1 | RowhpSwitchCosProtocolConfigEntry | not-accessible | mandatory | The information associated with each CoS protocol configuration. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.3.1.1 | ColumnhpSwitchCosProtocolType | read-only | mandatory | Packets with this protocol type will receive the new priority value. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.3.1.2 | ColumnhpSwitchCosProtocolPriority | read-write | mandatory | The 802.1p priority value to assign to packets received for the specified protocol. This value will be inserted in the 802.1Q tag and the packet will be placed… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4 | TablehpSwitchCosAddressConfigTable | not-accessible | mandatory | A table that contains information about the CoS address configurations on this switch. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4.1 | RowhpSwitchCosAddressConfigEntry | not-accessible | mandatory | The information associated with each CoS address configuration. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4.1.1 | ColumnhpSwitchCosAddressIndex | read-only | mandatory | The index that uniquely identifies the CoS configuration for an address for which this entry contains information. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4.1.2 | ColumnhpSwitchCosAddressType | read-write | mandatory | The type of address to configure. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4.1.3 | ColumnhpSwitchCosAddressIp | read-write | mandatory | This variable is valid only if an IP CoS configuration was defined. It will be ignored otherwise. Packets with this IP address as a source or destination will … |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4.1.4 | ColumnhpSwitchCosAddressPriority | read-write | mandatory | The 802.1p priority value to assign to packets received for the specified address. This value will be inserted in the 802.1Q tag and the packet will be placed … |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4.1.5 | ColumnhpSwitchCosAddressStatus | read-write | mandatory | The status of a Cos Address entry. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4.1.6 | ColumnhpSwitchCosAddressDSCPPolicy | read-write | mandatory | The DSCP Policy to assign to packets received for the specified address. This is an index into the hpSwitchCosDSCPPolicy table, or the value 255 indicating no … |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4.1.7 | ColumnhpSwitchCosAddressResolvedPriority | read-only | mandatory | The 802.1p priority that will be applied to packets received for the specified address. This value represents the actual operating value for this given address… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.4.1.8 | ColumnhpSwitchCosAddressApplyPolicy | read-write | mandatory | This object determines which configuration policy, hpSwitchCosAddressPriority or hpSwitchCosDSCPPolicy, applies for the given Address CoS entry. These configur… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.5 | NodehpSwitchCosTosConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.5.1 | ScalarhpSwitchCosTosConfigMode | read-write | mandatory | The operational status of Type of Service based Class of Service. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.5.2 | TablehpSwitchCosTosConfigTable | not-accessible | mandatory | A table that contains information about the CoS Type of Service configurations on this switch. This table is used only when the hpSwitchCosTosConfigMode is set… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.5.2.1 | RowhpSwitchCosTosConfigEntry | not-accessible | mandatory | The information associated with each CoS TOS configuration. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.5.2.1.1 | ColumnhpSwitchCosTosIndex | read-only | mandatory | Packets with this value in the upper bits of the Type of Service field of the IP protocol header will receive the new priority value. For Differentiated Servic… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.5.2.1.2 | ColumnhpSwitchCosTosPriority | read-write | deprecated | The 802.1p priority value to assign to packets received for the specified TOS. This value will be inserted in the 802.1Q tag and the packet will be placed in t… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.5.2.1.3 | ColumnhpSwitchCosTosDSCPPolicy | read-write | mandatory | The DSCP Policy to assign to packets received for the specified ToS codepoint. This is an index into the hpSwitchCosDSCPPolicy table, or the value 255 indicati… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.5.2.1.4 | ColumnhpSwitchCosTosResolvedPriority | read-only | mandatory | The 802.1p priority that will be applied to packets received for the specified ToS. This value represents the actual operating value for this given ToS entry. … |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.5.2.1.5 | ColumnhpSwitchCosTosApplyPolicy | read-write | mandatory | This object determines which configuration policy, applyInheritedPriority or hpSwitchCosTosDSCPPolicy, applies for the given Tos CoS entry. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.6 | TablehpSwitchCosDSCPPolicyConfigTable | not-accessible | mandatory | A table that contains information about the priority applied to each of the Differentiated Services Code Points. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.6.1 | RowhpSwitchCosDSCPPolicyConfigEntry | not-accessible | mandatory | A list of objects describing a DiffServe Codepoint (DSCP), and the 802.1p priority to apply for that DSCP. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.6.1.1 | ColumnhpSwitchCosDSCPPolicyIndex | not-accessible | mandatory | An index to uniquely identify each row in the hpSwitchCosDSCPPolicyConfigTable. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.6.1.2 | ColumnhpSwitchCosDSCPPolicyPriority | read-write | mandatory | The 802.1p priority value to assign to packets with a given DSCP. This value will be inserted in the 802.1Q tag and the packet will be placed in the appropriat… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.6.1.3 | ColumnhpSwitchCosDSCPPolicyName | read-write | mandatory | A user settable name describing a DSCP policy table entry. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7 | TablehpSwitchCosAppTypeConfigTable | not-accessible | mandatory | A table that contains information about the CoS Application type configurations on the switch. An application is determined by its network source and/or destin… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1 | RowhpSwitchCosAppTypeConfigEntry | not-accessible | mandatory | An entry in the switch hpSwitchCosAppTypeConfigEntry Table. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.1 | ColumnhpSwitchCosAppTypeConfigIndex | not-accessible | mandatory | An index to uniquely identify this hpSwitchCosAppType row. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.2 | ColumnhpSwitchCosAppTypeConfigType | read-write | mandatory | This signifies which network port number to apply to the given CoS Application policy. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.3 | ColumnhpSwitchCosAppTypeSrcPort | read-write | mandatory | This object represents the source network port that this policy applies to. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.4 | ColumnhpSwitchCosAppTypeDestPort | read-write | mandatory | This object represents the destination network port that this policy applies to. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.5 | ColumnhpSwitchCosAppTypePriority | read-write | mandatory | The 802.1p priority that should be applied to packets containing the particular configured source and/or destination port number in this entry. A value of 255 … |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.6 | ColumnhpSwitchCosAppTypeDSCPPolicy | read-write | mandatory | The DSCP Policy to assign to packets received for the specified application. This is an index into the hpSwitchCosDSCPPolicy table, or the value 255 indicating… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.7 | ColumnhpSwitchCosAppTypeResolvedPriority | read-only | mandatory | The 802.1p priority that will be applied to packets received on the specified application. This value represents the actual operating value for this CoS applic… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.8 | ColumnhpSwitchCosAppTypeApplyPolicy | read-write | mandatory | This object determines which configuration policy, hpSwitchCosAppTypePriority or hpSwitchCosAppTypeDSCPPolicy, applies for the given AppType CoS entry. These c… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.9 | ColumnhpSwitchCosAppTypeStatus | read-write | mandatory | This object is used to create and delete in the hpSwitchCosAppType table. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.10 | ColumnhpSwitchCosAppTypeMaxSrcPort | read-write | mandatory | This object represents the maximum source network port that this policy applies to. If a single, specific port is being used and not a range, then value of thi… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.7.1.11 | ColumnhpSwitchCosAppTypeMaxDestPort | read-write | mandatory | This object represents the maximum destination network port that this policy applies to. If a single, specific port is being used and not a range, then value o… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.8 | ScalarhpSwitchCosLastChange | read-only | mandatory | The value of the agent's sysUptime when the last time this device experienced a change in the Class of Service configuration. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.17.9 | ScalarhpSwitchConfigCosLastConfigError | read-only | mandatory | The type of the last QoS configuration result or error. This object is updated for each new QoS configuration. It is reset upon reboot. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.18 | NodehpSwitchMeshConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.18.1 | ScalarhpSwitchMeshMulticastAgingMode | read-write | deprecated | With meshing active, a value of aging will cause learned multicast addresses to be aged out within the required address aging interval. A setting of nonaging w… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.18.2 | ScalarhpSwitchMeshBackwardCompatibility | read-write | mandatory | Due to some hardware differences, the Series 1600/24xx/4000/8000 switches cannot be used directly in a mesh environment with Series 5300XL switches. Series 530… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.19 | NodehpSwitchPortIsolationConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.19.1 | ScalarhpSwitchPortIsolationMode | read-write | mandatory | This enables the port isolation feature on the device. Note: Enabling this feature may require VLANS to be configured properly. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.19.2 | TablehpSwitchPortIsolationConfigTable | not-accessible | mandatory | A table that contains information about the CoS Application type configurations on the switch. An application is determined by its network source and/or destin… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.19.2.1 | RowhpSwitchPortIsolationConfigEntry | not-accessible | mandatory | An entry in the switch hpSwitchPortIsolationConfigEntry Table. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.19.2.1.1 | ColumnhpSwitchPortIsolationPort | not-accessible | mandatory | An entry in the IfIndex table representing a logical port on this switch. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.19.2.1.2 | ColumnhpSwitchPortIsolationPortMode | read-write | mandatory | Defines the operational mode of a port when Port Isolation feature is enabled. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.20 | NodehpSwitchSshConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.20.1 | ScalarhpSwitchSshAdminStatus | read-write | mandatory | The status of the SSH operation. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.20.2 | ScalarhpSwitchSshVersion | read-write | mandatory | The version of the SSH protocol to run. 'version1' will accept connections from v1.3 or v1.5 clients. 'version2' will accept connections only from v2.0 clients… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.20.3 | ScalarhpSwitchSshTimeout | read-write | mandatory | The maximum length of time (in seconds) between the wakeup of SSH task and successful protocol negotiation and authentication. The default is 120 seconds. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.20.4 | ScalarhpSwitchSshPortNumber | read-write | mandatory | The port number on which SSH daemon should listen for connection requests. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.20.5 | ScalarhpSwitchSshServerKeySize | read-write | mandatory | Specifies the key size (in bits) of version 1 SSH host rsa key |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.20.6 | ScalarhpSwitchSshFileServerAdminStatus | read-write | mandatory | Specifies whether or not the SSH daemon will accept and process file transfer requests. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.20.7 | ScalarhpSwitchSshIpVersion | read-write | mandatory | The types of IP connections SSH will support. 'ipv4' will accept connections from Ipv4 clients. 'ipv6' will accept connections only from ipv6 clients. The defa… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.21 | NodehpSwitchPendingConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.21.1 | ScalarhpSwitchPendingConfigControl | read-write | mandatory | The object controls switch pending configuration. If set to the 'applyMstp' value the object applies pending Multiple Spanning Tree Protocol (MSTP) configurati… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.22 | NodehpSwitchBWMinConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.22.1 | TablehpSwitchBWMinEgressPortConfigTable | not-accessible | deprecated | New definitions under HP-ICF-RATE-LIMIT-MIB. A table that contains information about the port's egress Guaranteed Minimum Bandwidth configurations on this swit… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.22.1.1 | RowhpSwitchBWMinEgressPortConfigEntry | not-accessible | deprecated | New definitions under HP-ICF-RATE-LIMIT-MIB. The information associated with each port's egress Guaranteed Minimum Bandwidth configuration. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.22.1.1.1 | ColumnhpSwitchBWMinEgressPortIndex | read-only | deprecated | New definitions under HP-ICF-RATE-LIMIT-MIB. The ifIndex value which uniquely identifies a row in the Interfaces Table. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.22.1.1.2 | ColumnhpSwitchBWMinEgressPortPrctLowPriority | read-write | deprecated | New definitions under HP-ICF-RATE-LIMIT-MIB. The percentage of Guaranteed Minimum bandwidth to be assigned to the egress Low-Priority queue for this port. Tota… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.22.1.1.3 | ColumnhpSwitchBWMinEgressPortPrctNormalPriority | read-write | deprecated | New definitions under HP-ICF-RATE-LIMIT-MIB. The percentage of Guaranteed Minimum bandwidth to be assigned to the egress Normal-Priority queue for this port. T… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.22.1.1.4 | ColumnhpSwitchBWMinEgressPortPrctMedPriority | read-write | deprecated | New definitions under HP-ICF-RATE-LIMIT-MIB. The percentage of Guaranteed Minimum bandwidth to be assigned to the egress Medium-Priority queue for this port. T… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.22.1.1.5 | ColumnhpSwitchBWMinEgressPortPrctHighPriority | read-write | deprecated | New definitions under HP-ICF-RATE-LIMIT-MIB. The percentage of Guaranteed Minimum bandwidth to be assigned to the egress High-Priority queue for this port. Tot… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23 | NodehpSwitchRateLimitPortConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23.1 | TablehpSwitchRateLimitPortConfigTable | not-accessible | mandatory | A table that contains information about the port Rate-Limiting configurations on this switch. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23.1.1 | RowhpSwitchRateLimitPortConfigEntry | not-accessible | mandatory | The information associated with each port's Rate-Limiting configuration. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23.1.1.1 | ColumnhpSwitchRateLimitPortIndex | read-only | mandatory | The ifIndex value which uniquely identifies a row in the Interfaces Table. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23.1.1.2 | ColumnhpSwitchRateLimitPortControlMode | read-write | mandatory | The mode by which this port will be Rate-Limited on ingress. If rateLimitPerPortOnly is configured, there will be a single maximum rate for the entire port. If… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23.1.1.3 | ColumnhpSwitchRateLimitPortSingleControlPrct | read-write | mandatory | When hpSwitchRateLimitPortControlMode is configured for rateLimitPerPortOnly, this value is the maximum percentage of traffic that may be received by this port… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23.1.1.4 | ColumnhpSwitchRateLimitPortPrctLowPriority | read-write | mandatory | The maximum percentage of traffic that may be received by this port's Low-Priority queue on ingress. hpSwitchRateLimitPortControlMode must be configured to use… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23.1.1.5 | ColumnhpSwitchRateLimitPortPrctNormalPriority | read-write | mandatory | The maximum percentage of traffic that may be received by this port's Normal-Priority queue on ingress. hpSwitchRateLimitPortControlMode must be configured to … |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23.1.1.6 | ColumnhpSwitchRateLimitPortPrctMedPriority | read-write | mandatory | The maximum percentage of traffic that may be received by this port's Medium-Priority queue on ingress. hpSwitchRateLimitPortControlMode must be configured to … |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.23.1.1.7 | ColumnhpSwitchRateLimitPortPrctHighPriority | read-write | mandatory | The maximum percentage of traffic that may be received by this port's High-Priority queue on ingress. hpSwitchRateLimitPortControlMode must be configured to us… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.24 | NodehpSwitchQosPassThroughMode | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.24.1 | ScalarhpSwitchQosPassThroughModeConfig | read-write | mandatory | Specify the queue configuration mode for the switch. While changing the queue configuration mode this feature momentarily require to bring down the logical por… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.25 | NodehpSwitchReboot | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.25.1 | ScalarhpSwitchRebootConfig | read-only | mandatory | This tells the status of the switch whether it requires reboot for some variable to get effective. The value of this variable can be yes (1) reboot is required… |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.25.2 | ScalarhpSwitchRebootFastBoot | read-write | mandatory | Specifies whether fastboot is enabled or not on the switch. |
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.26 | NodehpSwitchProtectedPortsConfig | |||
| 1.3.6.1.4.1.11.2.14.11.5.1.7.1.26.1 | ScalarhpSwitchProtectedPortsMask | read-write | mandatory | This variable specifies a group of ports that are not allowed to communicate to each-other. Each octet within the value of this object specifies a set of eight… |