CTATX-MIB
743 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter enterprises Gauge IpAddress TimeTicks |
| RFC1213-MIB | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.97 | Nodesigma | |||
| 1.3.6.1.4.1.97.1 | Nodesys | |||
| 1.3.6.1.4.1.97.1.1 | ScalarsysID | read-only | mandatory | An integer which serves to identify the type of ES/1. |
| 1.3.6.1.4.1.97.1.2 | ScalarsysReset | read-write | mandatory | The time, in centiseconds, before the ES/1 should reboot. A GetResponse value of zero indicates that no reboot time has been specified. |
| 1.3.6.1.4.1.97.1.3 | ScalarsysTrapAck | read-write | mandatory | Whether the NMS will acknowledge the enterprise specific traps. |
| 1.3.6.1.4.1.97.1.4 | ScalarsysTrapTime | read-write | mandatory | The time, in centiseconds, which should expire between the sending of traps. This value is used when no ICMP source quench datagrams have been received. The ES… |
| 1.3.6.1.4.1.97.1.5 | ScalarsysTrapRetry | read-write | mandatory | The time, in centiseconds, which should expire before an unacknowledged Trap is re-transmitted. |
| 1.3.6.1.4.1.97.1.6 | ScalarsysTrapPort | read-write | mandatory | Zero, or the UDP port number to which a second copy of SNMP traps should be sent. Valid values are zero through 65535. |
| 1.3.6.1.4.1.97.3 | Nodeecs-1 | |||
| 1.3.6.1.4.1.97.3.1 | Nodehw | |||
| 1.3.6.1.4.1.97.3.1.1 | ScalarhwNumber | read-only | mandatory | The number of slots available for hardware modules, regardless of whether or not the slots are currently populated. This number is fixed as 7. |
| 1.3.6.1.4.1.97.3.1.2 | TablehwSlotTable | not-accessible | mandatory | A list of the most recent occupants of the slots; one per slot. |
| 1.3.6.1.4.1.97.3.1.2.1 | RowhwEntry | not-accessible | mandatory | A set of objects for each slot. |
| 1.3.6.1.4.1.97.3.1.2.1.1 | ColumnhwIndex | read-only | mandatory | The slot number, beginning with 1 for the top-most slot. This number always matches the instance of the hwEntry. For example, {hwIndex 3} contains the value '3… |
| 1.3.6.1.4.1.97.3.1.2.1.2 | ColumnhwType | read-only | mandatory | The module type of the slot's most recent occupant since the ES/1 was started. The values for hwType correspond to the values for hwPortType. |
| 1.3.6.1.4.1.97.3.1.2.1.3 | ColumnhwUseMod | read-write | mandatory | Whether to use this module, not applicable for the Packet Processing Engine. The value of hwUseMod is not saved if the ES/1 reboots. If the module fails diagno… |
| 1.3.6.1.4.1.97.3.1.2.1.4 | ColumnhwDefType | read-only | mandatory | The module type defined for the slot. Certain pre-defined relationships exist. Slot 1 always contains the Packet Processing Engine board. Slots 2-6 are either … |
| 1.3.6.1.4.1.97.3.1.2.1.5 | ColumnhwDiagStatus | read-only | mandatory | Results of diagnostics, when diagnostics were last performed on the module (whenever a module is released from reset, which is usually at power-up). |
| 1.3.6.1.4.1.97.3.1.2.1.6 | ColumnhwInuse | read-only | mandatory | Whether the module is currently executing its operational software. |
| 1.3.6.1.4.1.97.3.1.2.1.7 | ColumnhwDiagCode | read-only | mandatory | Additional diagnostics information concerning the slot's module. The meaning of hwDiagCode depends upon the slot's module type described by the hwType paramete… |
| 1.3.6.1.4.1.97.3.1.2.1.8 | ColumnhwManufData | read-only | mandatory | This is a 24 byte array which contains the part number, serial number and hardware revision level of this module. The Turbo's hwManufData will be all blanks si… |
| 1.3.6.1.4.1.97.3.1.2.1.9 | ColumnhwPortType | read-only | mandatory | This is a variable-length byte array, where each element represents the port types belonging to this module. The Packet Processing Engine's ports are fixed as … |
| 1.3.6.1.4.1.97.3.1.2.1.10 | ColumnhwPortStatus | read-only | mandatory | This is a variable-length byte array, where each element represents the status of the port belonging to this module. Values of 01 (status-good) or hex ff (stat… |
| 1.3.6.1.4.1.97.3.1.2.1.11 | ColumnhwUsePort | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.1.2.1.12 | ColumnhwDefPortType | read-only | mandatory | This is a variable-length byte array, where each element represents the port types defined for the module. If hwDefPortType does not match hwPortType, then the… |
| 1.3.6.1.4.1.97.3.1.2.1.13 | ColumnhwAddr1 | read-only | mandatory | The unique hard-wired 48 bit MAC address for the module's 1st port. For the Packet Processing Engine, it's a unique MAC address to be used as part of the ES/1'… |
| 1.3.6.1.4.1.97.3.1.2.1.14 | ColumnhwAddr2 | read-only | mandatory | The unique hard-wired 48 bit MAC address for the module's 2nd port, only applicable for IOMs. |
| 1.3.6.1.4.1.97.3.1.2.1.15 | ColumnhwAddr3 | read-only | mandatory | The unique hard-wired 48 bit MAC address for the module's 3rd port, only applicable for IOMs. |
| 1.3.6.1.4.1.97.3.1.2.1.16 | ColumnhwAddr4 | read-only | mandatory | The unique hard-wired 48 bit MAC address for the module's 4th port, only applicable for IOMs. |
| 1.3.6.1.4.1.97.3.1.2.1.17 | ColumnhwTempOK | read-only | mandatory | The temperature condition of the module, where True indicates temperature okay, and False indicates temperature too hot. |
| 1.3.6.1.4.1.97.3.1.2.1.18 | ColumnhwFirstPort | read-only | mandatory | The ifIndex number of the first port which resides within this module. [Not applicable for the Turbo.] |
| 1.3.6.1.4.1.97.3.1.2.1.19 | ColumnhwFatalErr | read-only | mandatory | This is a 32 byte array which contains information about the cause of the module's last unexpected self-reset, since the ES/1 booted.For the Packet Processing … |
| 1.3.6.1.4.1.97.3.1.2.1.20 | ColumnhwRptrPorts | read-only | mandatory | This is a variable-length byte array, where each element represents the repeater capability of the port belonging to this module. The element value is zero if … |
| 1.3.6.1.4.1.97.3.1.2.1.21 | ColumnhwPortSubType | read-only | mandatory | This is a variable-length byte array, where each element represents additional port type information. |
| 1.3.6.1.4.1.97.3.1.2.1.22 | ColumnhwAddr5 | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.1.2.1.23 | ColumnhwAddr6 | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.1.2.1.24 | ColumnhwAddr7 | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.1.2.1.25 | ColumnhwAddr8 | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.1.3 | ScalarhwSysBus | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.1.4 | ScalarhwPpeType | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.1.5 | ScalarhwSysProcessor | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.2 | Nodesw | |||
| 1.3.6.1.4.1.97.3.2.1 | ScalarswNumber | read-only | mandatory | The number of file sets. This number is fixed as 2. |
| 1.3.6.1.4.1.97.3.2.2 | TableswFilesetTable | not-accessible | mandatory | A list of the software file sets stored in the ES/1. The first file set refers to the file set that was used when the ES/1 last booted. The second file set ref… |
| 1.3.6.1.4.1.97.3.2.2.1 | RowswFileset | not-accessible | mandatory | A set of objects for each file set. |
| 1.3.6.1.4.1.97.3.2.2.1.1 | ColumnswIndex | read-only | mandatory | The file set number, beginning with 1 for the first file set. This number always matches the instance of the swFiles. For example, {swIndex 2} contains the val… |
| 1.3.6.1.4.1.97.3.2.2.1.3 | ColumnswDesc | read-only | mandatory | The description (0-255 bytes) of the software file set. |
| 1.3.6.1.4.1.97.3.2.2.1.4 | ColumnswCount | read-only | mandatory | The number of files in the file set. This number may range from 1 to 255. |
| 1.3.6.1.4.1.97.3.2.2.1.5 | ColumnswTypes | read-only | mandatory | The types of the files within the file set.The size of swFileTypes may be determined by swCount. The possible file types are none (0) File not present ppe-turb… |
| 1.3.6.1.4.1.97.3.2.2.1.6 | ColumnswSizes | read-only | mandatory | An array (4 octets per file), containing the size of each of the files. Each size is encoded as a series of 4 bytes, which should be converted into a 32 bit in… |
| 1.3.6.1.4.1.97.3.2.2.1.7 | ColumnswStarts | read-only | mandatory | An array (4 octets per file), containing the software's execution starting address of each of the files. Each address is encoded as a series of 4 bytes, which … |
| 1.3.6.1.4.1.97.3.2.2.1.8 | ColumnswBases | read-only | mandatory | An array (4 octets per file), containing the software's base loading address of each of the files. Each address is encoded as a series of 4 bytes, which should… |
| 1.3.6.1.4.1.97.3.2.2.1.9 | ColumnswFlashBank | read-only | mandatory | The bank number where the software file set resides. |
| 1.3.6.1.4.1.97.3.3 | Nodeadmin | |||
| 1.3.6.1.4.1.97.3.3.1 | Nodeconfig | |||
| 1.3.6.1.4.1.97.3.3.1.1 | ScalarconfigFatalErr | read-only | mandatory | This is a 32 byte array which contains information about the cause of the previous system reset. This will describe the circumstances which forced the system s… |
| 1.3.6.1.4.1.97.3.3.1.2 | ScalarconfigAnyPass | read-write | mandatory | The authentication password (0-24 bytes) which must match the community name in an SNMP PDU, in order for the operation to be performed. A zero length password… |
| 1.3.6.1.4.1.97.3.3.1.3 | ScalarconfigGetPass | read-write | mandatory | The authentication password (0-24 bytes) which must match the community name in an SNMP Get PDU (except for Debug or password parameters). A zero length passwo… |
| 1.3.6.1.4.1.97.3.3.1.4 | ScalarconfigNMSAddress | read-write | mandatory | The address of the NMS to which Trap PDUs are to be sent. A value of zero indicates that Trap PDUs should be sent to the NMS last heard from. |
| 1.3.6.1.4.1.97.3.3.1.5 | ScalarconfigFunctions | read-only | mandatory | A bit field which describes the software functions supported by this ES/1. The possible values are: 0x0001 NMS, 0x0002 TBRIDGE, 0x0004 SBRIDGE, 0x0008 MESH, 0x… |
| 1.3.6.1.4.1.97.3.3.1.6 | ScalarconfigPowerAc1 | read-only | mandatory | Whether the first power supply has AC input. |
| 1.3.6.1.4.1.97.3.3.1.7 | ScalarconfigPowerAc2 | read-only | mandatory | Whether the second power supply has AC input. |
| 1.3.6.1.4.1.97.3.3.1.8 | ScalarconfigPowerDc1 | read-only | mandatory | Whether the first power supply provides DC voltage. |
| 1.3.6.1.4.1.97.3.3.1.9 | ScalarconfigPowerDc2 | read-only | mandatory | Whether the second power supply provides DC voltage. |
| 1.3.6.1.4.1.97.3.3.1.10 | ScalarconfigPowerPresent1 | read-only | mandatory | Whether the first power supply is present. |
| 1.3.6.1.4.1.97.3.3.1.11 | ScalarconfigPowerPresent2 | read-only | mandatory | Whether the second power supply is present. |
| 1.3.6.1.4.1.97.3.3.1.12 | ScalarconfigAlarmDynamic | read-write | mandatory | Whether changes in dynamic parameters (except for the dynamically learned addresses) should cause enterprise specific trap PDUs to be generated. |
| 1.3.6.1.4.1.97.3.3.1.13 | ScalarconfigAlarmAddresses | read-write | mandatory | Whether changes in the dynamically learned addresses should cause enterprise specific trap PDUs to be generated. |
| 1.3.6.1.4.1.97.3.3.1.14 | ScalarconfigStorageFailure | read-only | mandatory | Whether the ES/1's storage facility for its configuration parameters has failed (the ES/1 may not be able to reboot after such a failure). |
| 1.3.6.1.4.1.97.3.3.1.15 | ScalarconfigAuthenticationFailure | read-only | mandatory | All nulls, or the IP source address within the last SNMP PDU which caused an SNMP authentication failure. |
| 1.3.6.1.4.1.97.3.3.1.16 | ScalarconfigFddiPriority | read-write | mandatory | Priority to use when forwarding packets to any FDDI port from any non-FDDI port. |
| 1.3.6.1.4.1.97.3.3.1.17 | ScalarconfigTprPriority | read-write | mandatory | Priority to use when forwarding packets to any Token-Ring port from any non-Token-Ring port. |
| 1.3.6.1.4.1.97.3.3.1.19 | ScalarconfigDumpModule | read-write | mandatory | Flag to select the module to dump on a crash. If set to a value of 1 to 7 the relevant module's memory will be sent to the UART port on detecting a fatal error… |
| 1.3.6.1.4.1.97.3.3.1.20 | ScalarconfigDumpStart | read-write | mandatory | Starting address of memory to dump upon detecting a fatal error. |
| 1.3.6.1.4.1.97.3.3.1.21 | ScalarconfigDumpEnd | read-write | mandatory | Ending address of memory to dump upon detecting a fatal error. |
| 1.3.6.1.4.1.97.3.3.2 | Nodelma | |||
| 1.3.6.1.4.1.97.3.3.2.1 | ScalarlmaAllAddr | read-write | mandatory | The IEEE All LANs Bridge Management Group Address 01-80-c2-00-00-10. Changing lmaAllAddr will not take effect until the ES/1 reboots. |
| 1.3.6.1.4.1.97.3.3.2.2 | ScalarlmaAnyAddr | read-write | mandatory | A spare LMA address, which is always all zeroes. Changing lmaAllAny will not take effect until the ES/1 reboots. |
| 1.3.6.1.4.1.97.3.3.3 | Nodeppe | |||
| 1.3.6.1.4.1.97.3.3.3.1 | ScalarppeLrgUxRxCnt | read-write | mandatory | The number of large data buffers to allocate for the PPE to create packets. This value may be changed automatically by the ES/1 as a result of enabling IPX rou… |
| 1.3.6.1.4.1.97.3.3.3.2 | ScalarppeSmlUxRxCnt | read-write | mandatory | The number of small data buffers to allocate for the PPE to create packets. |
| 1.3.6.1.4.1.97.3.3.3.3 | ScalarppeUxTxCnt | read-write | mandatory | The maximum number of received packets destined to the ES/1 itself (versus those received packets to be forwarded) which can be stored, until the PPE is able t… |
| 1.3.6.1.4.1.97.3.3.3.4 | ScalarppeSmlBuffSize | read-write | mandatory | The size (in bytes) of the PPE's small data buffers. |
| 1.3.6.1.4.1.97.3.3.3.5 | ScalarppeBridgingMemory | read-only | mandatory | The percentage (1 - 99) of the PPE's memory that is allocated for MAC bridging. The PPE's remaining memory will be used for communicating with the NMS and for … |
| 1.3.6.1.4.1.97.3.3.3.6 | ScalarppeExtendStats | read-write | mandatory | Whether the PPE should accumulate extended statistics. Extended statistics are tallies, such as byte counts, which are not essential for everyday ES/1 manageme… |
| 1.3.6.1.4.1.97.3.3.3.7 | ScalarppeBAddrLimit | read-write | mandatory | The maximum number of addresses that the PPE should learn for bridging purposes. The remaining address entries will be used for routing related addresses. |
| 1.3.6.1.4.1.97.3.3.3.8 | ScalarppeTxCongests | read-only | mandatory | Number of packets not received due to internal buffer congestion. |
| 1.3.6.1.4.1.97.3.3.3.9 | ScalarppeArpEntries | read-only | mandatory | The number of ARP entries for all interfaces. |
| 1.3.6.1.4.1.97.3.3.3.10 | ScalarppeArpStatics | read-only | mandatory | The number of statically defined ARP entries for all interfaces. |
| 1.3.6.1.4.1.97.3.3.3.11 | ScalarppeArpOverflows | read-only | mandatory | The number of times a ARP entry could not be learned due to insufficient address table space. |
| 1.3.6.1.4.1.97.3.3.3.12 | ScalarppeIpEntries | read-only | mandatory | The number of IP Routing Database entries. |
| 1.3.6.1.4.1.97.3.3.3.13 | ScalarppeIpStatics | read-only | mandatory | The number of statically defined IP Routing Database entries. |
| 1.3.6.1.4.1.97.3.3.3.14 | ScalarppeStaticPreference | read-write | mandatory | The value to assign to ipRouteMetric2, when adding a statically-defined entry to the IP Routing Table. |
| 1.3.6.1.4.1.97.3.3.3.15 | ScalarppeOspfPreference | read-write | mandatory | The value to assign to ipRouteMetric2, when adding an OSPF-learned entry to the IP Routing Table. |
| 1.3.6.1.4.1.97.3.3.3.16 | ScalarppeRipPreference | read-write | mandatory | The value to assign to ipRouteMetric2, when adding a RIP-learned entry to the IP Routing Table. |
| 1.3.6.1.4.1.97.3.3.3.17 | ScalarppeEgpPreference | read-write | mandatory | The value to assign to ipRouteMetric2, when adding an EGP-learned entry to the IP Routing Table. |
| 1.3.6.1.4.1.97.3.3.3.18 | ScalarppeCpuUtilization | read-only | mandatory | The current CPU utilization on the Packet Processing Engine. |
| 1.3.6.1.4.1.97.3.3.3.19 | ScalarppeRipRouteDiscards | read-only | mandatory | The number of times a route learned via RIP was not added to the IP Routing Table due to insufficient Routing Table space. |
| 1.3.6.1.4.1.97.3.3.3.20 | ScalarppeOspfRouteDiscards | read-only | mandatory | The number of times a route learned via OSPF was not added to the IP Routing Table due to insufficient Routing Table space (currently always zero). |
| 1.3.6.1.4.1.97.3.3.3.21 | ScalarppeRouteMemorySize | read-only | mandatory | The number of bytes originally given to the routing table heap. |
| 1.3.6.1.4.1.97.3.3.3.22 | ScalarppeRouteMemoryAvail | read-only | mandatory | The number of bytes currently available in the routing table heap. |
| 1.3.6.1.4.1.97.3.3.3.23 | ScalarppeRouteMemoryFailures | read-only | mandatory | The number of unsuccessful attempts to allocate from the routing table heap. |
| 1.3.6.1.4.1.97.3.3.3.24 | ScalarppePacketMemorySize | read-only | mandatory | The number of bytes originally given to the packet heap. |
| 1.3.6.1.4.1.97.3.3.3.25 | ScalarppePacketMemoryAvail | read-only | mandatory | The number of bytes currently available in the packet heap. |
| 1.3.6.1.4.1.97.3.3.3.26 | ScalarppePacketMemoryFailures | read-only | mandatory | The number of unsuccessful attempts to allocate from the packet heap. |
| 1.3.6.1.4.1.97.3.3.3.27 | ScalarppeOspfPduMemoryFailures | read-only | mandatory | Number of unsuccessful attempts to allocate memory for an OSPF PDU. |
| 1.3.6.1.4.1.97.3.3.3.28 | ScalarppeOspfPduMemoryAllocs | read-only | mandatory | Number of times memory was allocated for an OSPF PDU. |
| 1.3.6.1.4.1.97.3.3.3.29 | ScalarppeIcmpPduMemoryFailures | read-only | mandatory | Number of unsuccessful attempts to allocate memory for an ICMP PDU. |
| 1.3.6.1.4.1.97.3.3.3.30 | ScalarppeIcmpPduMemoryAllocs | read-only | mandatory | Number of times memory was allocated for an ICMP PDU. |
| 1.3.6.1.4.1.97.3.3.3.31 | ScalarppeRipPduMemoryFailures | read-only | mandatory | Number of unsuccessful attempts to allocate memory for a RIP PDU. |
| 1.3.6.1.4.1.97.3.3.3.32 | ScalarppeRipPduMemoryAllocs | read-only | mandatory | Number of times memory was allocated for a RIP PDU. |
| 1.3.6.1.4.1.97.3.3.3.33 | ScalarppeBootpPduMemoryFailures | read-only | mandatory | Number of unsuccessful attempts to allocate memory for a BOOTP PDU. |
| 1.3.6.1.4.1.97.3.3.3.34 | ScalarppeBootpPduMemoryAllocs | read-only | mandatory | Number of times memory was allocated for a BOOTP PDU. |
| 1.3.6.1.4.1.97.3.3.3.35 | ScalarppeSnmpPduMemoryFailures | read-only | mandatory | Number of unsuccessful attempts to allocate memory for an SNMP PDU. |
| 1.3.6.1.4.1.97.3.3.3.36 | ScalarppeSnmpPduMemoryAllocs | read-only | mandatory | Number of times memory was allocated for an SNMP PDU. |
| 1.3.6.1.4.1.97.3.3.3.37 | ScalarppeTftpPduMemoryFailures | read-only | mandatory | Number of unsuccessful attempts to allocate memory for a TFTP PDU. |
| 1.3.6.1.4.1.97.3.3.3.38 | ScalarppeTftpPduMemoryAllocs | read-only | mandatory | Number of times memory was allocated for a TFTP PDU. |
| 1.3.6.1.4.1.97.3.3.3.39 | ScalarppeTraceroutePduMemoryFailures | read-only | mandatory | Number of unsuccessful attempts to allocate memory for a TraceRoute PDU. |
| 1.3.6.1.4.1.97.3.3.3.40 | ScalarppeTraceroutePduMemoryAllocs | read-only | mandatory | Number of times memory was allocated for a TraceRoute PDU. |
| 1.3.6.1.4.1.97.3.3.3.41 | ScalarppeArpPduMemoryFailures | read-only | mandatory | Number of unsuccessful attempts to allocate memory for a ARP PDU. |
| 1.3.6.1.4.1.97.3.3.3.42 | ScalarppeArpPduMemoryAllocs | read-only | mandatory | Number of times memory was allocated for a ARP PDU. |
| 1.3.6.1.4.1.97.3.3.3.43 | ScalarppeIgmpPduMemoryFailures | read-only | mandatory | Number of unsuccessful attempts to allocate memory for a IGMP PDU. |
| 1.3.6.1.4.1.97.3.3.3.44 | ScalarppeIgmpPduMemoryAllocs | read-only | mandatory | Number of times memory was allocated for a IGMP PDU. |
| 1.3.6.1.4.1.97.3.3.3.45 | ScalarppeAresAsStes | read-write | mandatory | If true, all-routes-explorers will be treated as if they were spanning-tree-explorers. |
| 1.3.6.1.4.1.97.3.3.3.46 | ScalarppeRoutePercent | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.3.3.48 | ScalarppeMgtMemorySize | read-only | mandatory | The number of bytes originally given to the local management agent heap. |
| 1.3.6.1.4.1.97.3.3.3.49 | ScalarppeMgtMemoryAvail | read-only | mandatory | The number of bytes currently available in the local management agent heap. |
| 1.3.6.1.4.1.97.3.3.3.50 | ScalarppeMgtMemoryFailures | read-only | mandatory | The number of unsuccessful attempts to allocate from the local management agent heap. |
| 1.3.6.1.4.1.97.3.3.4 | Nodest | |||
| 1.3.6.1.4.1.97.3.3.4.1 | ScalarstGroupAddr | read-write | mandatory | The Spanning Tree Group address, normally 01-80-c2-00-00-00. Changing stGroupAddr will not take effect until the ES/1 reboots. |
| 1.3.6.1.4.1.97.3.3.4.2 | ScalarstResAddr | read-write | mandatory | A series of 90 octets containing the Spanning Tree's 15 reserved addres 01-80-c2-00-00-01 through 01-80-c2-00-00-0f). Changing stResAddr will not take effect u… |
| 1.3.6.1.4.1.97.3.3.4.3 | ScalarstBridgeId | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.3.4.4 | ScalarstRootMaxAge | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.3.4.5 | ScalarstRootHello | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.3.4.6 | ScalarstRootDelay | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.3.4.7 | ScalarstRootID | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.3.4.8 | ScalarstRootCost | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.3.4.9 | ScalarstRootPort | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.3.4.10 | ScalarstTopChange | read-only | mandatory | Whether a topology change is currently in progress. |
| 1.3.6.1.4.1.97.3.3.4.11 | ScalarstActMaxAge | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.3.4.12 | ScalarstActHello | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.3.4.13 | ScalarstActDelay | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.3.4.14 | ScalarstTopChangeCount | read-write | mandatory | The number of spanning tree topology changes which have occurred, since the ES/1 was last booted (or this parameter was last reset by the NMS). |
| 1.3.6.1.4.1.97.3.3.4.15 | ScalarstTopChangeTime | read-only | mandatory | If stTopChange is True, then the time since stTopChange changed from False to True. If stTopChange is False, then the time since stTopChange changed from True … |
| 1.3.6.1.4.1.97.3.3.4.16 | ScalarstAgeTime | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.3.5 | Nodemesh | |||
| 1.3.6.1.4.1.97.3.3.5.1 | ScalarmeshCostPercent | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.3.5.2 | ScalarmeshCost | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.3.5.3 | ScalarmeshCostChange | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.3.5.4 | ScalarmeshCostChangeCount | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.3.5.5 | ScalarmeshCostChangeTime | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.3.5.6 | ScalarmeshSubnet | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.4 | Nodeswdis | |||
| 1.3.6.1.4.1.97.3.4.1 | ScalarswdisDesc | read-only | mandatory | The description (0-32 bytes) of the software set currently being downloaded, or a description of the software set last downloaded since the ES/1 booted. |
| 1.3.6.1.4.1.97.3.4.2 | ScalarswdisAccess | read-write | mandatory | The version of software that may be downloaded. Attempts to download other versions of software will be rejected. The value for swdisAccess is embedded within … |
| 1.3.6.1.4.1.97.3.4.3 | ScalarswdisWriteStatus | read-only | mandatory | The status of the erase/write operation. |
| 1.3.6.1.4.1.97.3.4.4 | ScalarswdisConfigIp | read-write | mandatory | The IP address of the NMS (i.e., any IP host) that is allowed to use TFTP to send/retrieve the configuration file of the ES/1. A value of 0.0.0.0 (which is the… |
| 1.3.6.1.4.1.97.3.4.5 | ScalarswdisConfigRetryTime | read-write | mandatory | The number of seconds that the ES/1 will wait for an acknowledgment before it retransmits an unacknowledged TFTP data block. The factory specified default is 5… |
| 1.3.6.1.4.1.97.3.4.6 | ScalarswdisConfigTotalTimeout | read-write | mandatory | The number of seconds that the ES/1 will wait for an acknowledgment to a data block before it cancels a TFTP session. The factory specified default is 25 secon… |
| 1.3.6.1.4.1.97.3.5 | Nodeaddr | |||
| 1.3.6.1.4.1.97.3.5.1 | ScalaraddrStatics | read-only | mandatory | The number of static addresses which are currently stored in the ES/1. |
| 1.3.6.1.4.1.97.3.5.2 | ScalaraddrDynamics | read-only | mandatory | The number of learned addresses in the address table. |
| 1.3.6.1.4.1.97.3.5.3 | ScalaraddrDynamicMax | read-write | mandatory | The maximum number of spanning tree addresses which have been learned since the ES/1 was last booted (or this parameter was last reset by the NMS). |
| 1.3.6.1.4.1.97.3.5.4 | ScalaraddrMeshs | read-only | mandatory | The number of ATM, Frame Relay, and/or SMDS addresses in the address table. These addresses are not reflected within addrStatics nor addrDynamics. [ATM, Frame … |
| 1.3.6.1.4.1.97.3.5.5 | ScalaraddrDynamicOverflows | read-only | mandatory | The number times an address was not learned due to insufficient address table space. |
| 1.3.6.1.4.1.97.3.5.6 | ScalaraddrMeshOverflows | read-only | mandatory | The number of times an ATM, Frame Relay, or SMDS address could not be learned due to insufficient address table space. [ATM, Frame Relay, and SMDS are not yet … |
| 1.3.6.1.4.1.97.3.5.7 | ScalaraddrFlags | read-write | mandatory | Flags to describe the use and control of this address entry. Each bit has a different meaning. The NMS must always set either entry-static, entry-none, or entr… |
| 1.3.6.1.4.1.97.3.5.8 | ScalaraddrMAC | read-write | mandatory | The MAC address for this address definition. |
| 1.3.6.1.4.1.97.3.5.9 | ScalaraddrPort | read-write | mandatory | The port through which this address is connected to the ES/1 (only valid for entry-dynamic-local, entry-statistics, and entry-port entries). |
| 1.3.6.1.4.1.97.3.5.10 | ScalaraddrPortMap | read-write | obsolete | This is a bitmap of up to 32 sets of 32 bits each (128 octets), which defines which source ports are allowed to forward packets to which destination ports. Wit… |
| 1.3.6.1.4.1.97.3.5.41 | ScalaraddrOperation | read-write | mandatory | The operation to be performed upon the described address. The possibilities include: read-random (1), read-next (2), zero-stats (3), update (4), delete (5), re… |
| 1.3.6.1.4.1.97.3.5.42 | ScalaraddrIndex | read-write | mandatory | The index number to be used for read-next and read-block operations. When the ES/1 boots, addrIndex is initialized to -1. |
| 1.3.6.1.4.1.97.3.5.44 | ScalaraddrNext | read-write | mandatory | The next value to use for addrIndex, when you use read-next or read-block operations to read the address table. When the ES/1 boots, addrNext is initialized to… |
| 1.3.6.1.4.1.97.3.5.45 | ScalaraddrAge | read-write | mandatory | The time, in centiseconds, since a packet was last received from the address on a port that was in Spanning Tree learning or forwarding state. If no packets ha… |
| 1.3.6.1.4.1.97.3.5.46 | ScalaraddrRxPkts | read-write | mandatory | The number of packets received from the address on a port that was in Spanning Tree learning or forwarding state (can be zeroed by zero-stats). |
| 1.3.6.1.4.1.97.3.5.47 | ScalaraddrRxChars | read-write | mandatory | The number of characters in the packets received from the address on a port that was in Spanning Tree Learning or Forwarding state (can be zeroed by zero-stats… |
| 1.3.6.1.4.1.97.3.5.48 | ScalaraddrRxMultiPkts | read-write | mandatory | The number of multicast packets received from the address on a port that was in Spanning Tree Learning or Forwarding state (can be zeroed by zero-stats). |
| 1.3.6.1.4.1.97.3.5.49 | ScalaraddrRxFwdPkts | read-write | mandatory | The number of packets received from the address which were forwarded (can be zeroed by zero-stats). This includes packets that were MAC-layer bridged because t… |
| 1.3.6.1.4.1.97.3.5.50 | ScalaraddrTxPkts | read-write | mandatory | The number of packets transmitted to the address (can be zeroed by zero-stats). |
| 1.3.6.1.4.1.97.3.5.51 | ScalaraddrTxChars | read-write | mandatory | The number of characters in the packets transmitted to the address (can be zeroed by zero-stats). |
| 1.3.6.1.4.1.97.3.5.52 | ScalaraddrBlockSize | read-write | mandatory | The number of addresses contained by addrBlock.This parameter is only used for dumping blocks of MAC addresses. |
| 1.3.6.1.4.1.97.3.5.53 | ScalaraddrBlock | read-write | mandatory | A series of 0-700 octets, which represents 0-100 addresses. Each address consists of a 6 octet MacAddress followed by a 1 byte port number. If the port number … |
| 1.3.6.1.4.1.97.3.5.54 | ScalaraddrAlarmMAC | read-only | mandatory | The MAC address for an address entry. This parameter is only used by the ES/1's enterprise specific trap mechanism. |
| 1.3.6.1.4.1.97.3.5.55 | ScalaraddrRptrPort | read-write | mandatory | The repeater port through which this address is connected to the port indicated by addrPort. This parameter is only valid if the port's srepeaterExtendedStats … |
| 1.3.6.1.4.1.97.3.6 | Nodesnmpsmt | |||
| 1.3.6.1.4.1.97.3.6.1 | ScalarsnmpsmtUpstreamReq | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.6.2 | ScalarsnmpsmtUpstreamRsp | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.6.3 | ScalarsnmpsmtUpstreamDescriptor | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.6.4 | ScalarsnmpsmtUpstreamState | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.6.5 | TablefddismtTable | not-accessible | mandatory | A list of snmpsmt entries, one per FDDI board. |
| 1.3.6.1.4.1.97.3.6.5.1 | RowfddismtEntry | not-accessible | mandatory | A set of objects for an interface entry. |
| 1.3.6.1.4.1.97.3.6.5.1.1 | ColumnfddismtIndex | read-only | mandatory | A unique value for each SMT. It represents the sequence number of the FDDI board in ES/1. |
| 1.3.6.1.4.1.97.3.6.5.1.2 | ColumnfddismtUpstreamReq | read-write | mandatory | When this variable is written, the ES/1 converts it into a big-endian FDDI address and issues an SMT NIF request to determine that address's upstream neighbor.… |
| 1.3.6.1.4.1.97.3.6.5.1.3 | ColumnfddismtUpstreamRsp | read-only | mandatory | The address of the upstream neighbor of the ES/1 whose address was written into snmpsmtUpstreamReq. If the address has not yet been learned, then an address of… |
| 1.3.6.1.4.1.97.3.6.5.1.4 | ColumnfddismtUpstreamDescriptor | read-only | mandatory | A four byte string containing the upstream neighbor's Station Descriptor parameter, as defined by the SMT frame protocols. If the upstream neighbor has not yet… |
| 1.3.6.1.4.1.97.3.6.5.1.5 | ColumnfddismtUpstreamState | read-only | mandatory | A four byte string containing the upstream neighbor's Station State parameter, as defined by the SMT frame protocols. If the upstream neighbor has not yet been… |
| 1.3.6.1.4.1.97.3.7 | Nodesinterfaces | |||
| 1.3.6.1.4.1.97.3.7.1 | ScalarsifUX | read-only | mandatory | The maximum number of receive data buffers supported by the ES/1. The sum of sifSmlRxCnt and sifLrgRxCnt for all ports, plus ppeSmlRxCnt and ppeLrgRxCnt must b… |
| 1.3.6.1.4.1.97.3.7.2 | TablesifTable | not-accessible | mandatory | A list of interface entries; one per port. |
| 1.3.6.1.4.1.97.3.7.2.1 | RowsifEntry | not-accessible | mandatory | A set of objects for an interface entry. |
| 1.3.6.1.4.1.97.3.7.2.1.1 | ColumnsifIndex | read-only | mandatory | The port number, beginning with 1 for the first port. |
| 1.3.6.1.4.1.97.3.7.2.1.2 | ColumnsifSmlRxCnt | read-only | mandatory | The number of small data buffers for receiving packets. |
| 1.3.6.1.4.1.97.3.7.2.1.3 | ColumnsifLrgRxCnt | read-write | mandatory | The number of large data buffers for receiving packets; must be zero for CSMA and UART ports. |
| 1.3.6.1.4.1.97.3.7.2.1.4 | ColumnsifUxTxCnt | read-write | mandatory | The maximum size of the port's transmit queue, i.e., the number of packets that can be in the port's transmit queue, waiting to be transmitted. |
| 1.3.6.1.4.1.97.3.7.2.1.5 | ColumnsifThreshold | read-write | mandatory | Maximum number of combined receive and transmit packet hardware errors before an alarm should be generated. |
| 1.3.6.1.4.1.97.3.7.2.1.6 | ColumnsifThresholdTime | read-write | mandatory | The time period (in seconds) to which sifThreshold applies. A value of zero will disable the sifThreshold alarm. |
| 1.3.6.1.4.1.97.3.7.2.1.7 | ColumnsifRxQueueThresh | read-write | mandatory | Maximum number of receive packet queue overflow errors before an alarm should be generated. |
| 1.3.6.1.4.1.97.3.7.2.1.8 | ColumnsifRxQueueThreshTime | read-write | mandatory | The time period (in seconds) to which sifRxQueueThresh applies. A value of zero will disable the sifRxQueueThresh alarm. |
| 1.3.6.1.4.1.97.3.7.2.1.9 | ColumnsifTxStormCnt | read-write | mandatory | The maximum number of multicasts to transmit with a certain period of time (not applicable for UART ports). |
| 1.3.6.1.4.1.97.3.7.2.1.10 | ColumnsifTxStormTime | read-write | mandatory | The period of time, in centiseconds, which qualifies sifTxStormCnt (not applicable for UART ports). |
| 1.3.6.1.4.1.97.3.7.2.1.11 | ColumnsifFilterFlags | read-write | mandatory | Special filter flags; any combination of the following bits: 0x0001 NO_SOURCE_SAME, 0x0002 NO_SOURCE_LEARNT, 0x0004 NO_LEARNING, 0x0008 NO_DEST_LEARNT |
| 1.3.6.1.4.1.97.3.7.2.1.12 | ColumnsifCongestTime | read-write | mandatory | When a port becomes congested, the PPE will discard any packets destined to the port for this many centiseconds following the congestion alarm. Possible values… |
| 1.3.6.1.4.1.97.3.7.2.1.13 | ColumnsifQueueTime | read-write | mandatory | The time, in centiseconds, after which an element in a transmit queue will be flushed. |
| 1.3.6.1.4.1.97.3.7.2.1.14 | ColumnsifPortCost | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.7.2.1.15 | ColumnsifStPriority | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.7.2.1.16 | ColumnsifFunctions | read-only | mandatory | The current functional state (protocols which have been activated and are operational) of the port. The following values or combinations are supported: 0x0001 … |
| 1.3.6.1.4.1.97.3.7.2.1.17 | ColumnsifCongested | read-only | mandatory | Whether the port is out-bound congested. |
| 1.3.6.1.4.1.97.3.7.2.1.18 | ColumnsifState | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.7.2.1.19 | ColumnsifDesigCost | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.7.2.1.20 | ColumnsifDesigRoot | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.7.2.1.21 | ColumnsifDesigBridge | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.7.2.1.22 | ColumnsifDesigPort | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.7.2.1.23 | ColumnsifRxPackets | read-only | mandatory | A 100 byte array, containing the number of received packets broken down into 25 categories. The number of packets in each category is encoded as a series of 4 … |
| 1.3.6.1.4.1.97.3.7.2.1.24 | ColumnsifRxChar0s | read-only | mandatory | Number of characters in the forwarded received packets. |
| 1.3.6.1.4.1.97.3.7.2.1.25 | ColumnsifRxChar1s | read-only | mandatory | Number of characters in the filtered received packets. |
| 1.3.6.1.4.1.97.3.7.2.1.26 | ColumnsifRxSizeErrors | read-only | mandatory | Number of received packets discarded due to size errors. |
| 1.3.6.1.4.1.97.3.7.2.1.27 | ColumnsifRxHwFCSs | read-only | mandatory | Number of received packets discarded due to FCS errors. |
| 1.3.6.1.4.1.97.3.7.2.1.28 | ColumnsifRxQueues | read-only | mandatory | Number of received packets lost because of insufficient receive buffers.(For certain interfaces with multi-packet FIFO hardware, this count might be approximat… |
| 1.3.6.1.4.1.97.3.7.2.1.30 | ColumnsifTxPackets | read-only | mandatory | A 20 byte array, containing the number of transmitted packets broken down into 5 categories. The number of packets in each category is encoded as a series of 4… |
| 1.3.6.1.4.1.97.3.7.2.1.31 | ColumnsifTxCongests | read-only | obsolete | |
| 1.3.6.1.4.1.97.3.7.2.1.32 | ColumnsifTxStorms | read-only | mandatory | Number of packets not sent due to protection against a multicast storm. |
| 1.3.6.1.4.1.97.3.7.2.1.33 | ColumnsifTxDests | read-only | mandatory | Number of packets not sent due to a destination port filtering restriction. |
| 1.3.6.1.4.1.97.3.7.2.1.34 | ColumnsifErrorsFlag | read-only | mandatory | Whether the port has exceeded the limits specified by sifThreshold and sifThresholdTime. |
| 1.3.6.1.4.1.97.3.7.2.1.35 | ColumnsifTxStormFlag | read-only | mandatory | Whether PPE has invoked multicast storm protection. |
| 1.3.6.1.4.1.97.3.7.2.1.36 | ColumnsifTxSizes | read-only | mandatory | Number of packets not sent due to size limitations. |
| 1.3.6.1.4.1.97.3.7.2.1.37 | ColumnsifTxAddr | read-only | mandatory | A series of 16 MAC addresses (96 octets in total), of the source addresses of the last 16 packets that were not sent due to packet size limitations. If fewer t… |
| 1.3.6.1.4.1.97.3.7.2.1.38 | ColumnsifLan | read-write | mandatory | Up to four group identifiers assigned to the port. The sifLan identifier is only used by combination filter testing, i.e., for comparisons against filterSrcLan… |
| 1.3.6.1.4.1.97.3.7.2.1.39 | ColumnsifStatisticsTime | read-only | mandatory | Length of time during which statistics were collected. In particular, the following statistics may be examined to determine the exact utilization rate of a por… |
| 1.3.6.1.4.1.97.3.7.2.1.40 | ColumnsifIpAddress | read-write | mandatory | The IP address assigned to the port. If this is zero, then the port must learn its IP address via Reverse ARP or PPP's IPCP. |
| 1.3.6.1.4.1.97.3.7.2.1.41 | ColumnsifIpGroupAddress | read-write | mandatory | Zero, or an IP Group address assigned to the port. |
| 1.3.6.1.4.1.97.3.7.2.1.42 | ColumnsifMaxPacketSize | read-write | mandatory | The maximum packet size, in bytes (octets), which may be transmitted through this port. This parameter may not be changed, except for PPP ports, in which case,… |
| 1.3.6.1.4.1.97.3.7.2.1.43 | ColumnsifExpectSqe | read-write | mandatory | Whether the port should expect SQE, also known as heartbeat (not applicable for ports other than CSMA/CD ports). |
| 1.3.6.1.4.1.97.3.7.2.1.44 | ColumnsifFilterLocal | read-write | mandatory | Whether the port should attempt to filter local traffic, bypassing all statistics accumulation, rather than passing the local traffic to the Packet Processing … |
| 1.3.6.1.4.1.97.3.7.2.1.45 | ColumnsifInQLen | read-write | mandatory | The maximum length ever obtained by the port's inbound packet queue (in packets). The size of a port's inbound packet queue is periodically polled (rather than… |
| 1.3.6.1.4.1.97.3.7.2.1.46 | ColumnsifFrameSwitching | read-write | mandatory | Valid only for Token Ring ports. Options include: enabled (1), disabled (2).Defaults to disabled(2). If enabled, frames may be bridged between token ring ports… |
| 1.3.6.1.4.1.97.3.7.2.1.47 | ColumnsifRingDrops | read-only | mandatory | Only valid for 802.5 token ring. Number of times the ring left the open state. |
| 1.3.6.1.4.1.97.3.7.2.1.48 | ColumnsifAdapterChecks | read-only | mandatory | Only valid for 802.5 token ring. Number of times the MAC chip experienced an internal hardware failure and had to be reset. |
| 1.3.6.1.4.1.97.3.7.2.1.49 | ColumnsifIpRipPortMetric | read-write | mandatory | Port metric for backup RIP interface. |
| 1.3.6.1.4.1.97.3.7.2.1.50 | ColumnsifDescr | read-write | mandatory | A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the h… |
| 1.3.6.1.4.1.97.3.7.3 | ScalarsifUtilInterval | read-only | mandatory | The number of seconds in each utilization sample. |
| 1.3.6.1.4.1.97.3.7.4 | ScalarsifUtilCount | read-only | mandatory | The number of same-kind peak samples per physical port accumulated in sifUtilPortPeakTable or sifUtilSysPeakTable. |
| 1.3.6.1.4.1.97.3.7.5 | ScalarsifUtilPortPeakReset | read-write | mandatory | This object is set to true (1) to erase earlier per-physical-port utilization samples on all specified port(s). |
| 1.3.6.1.4.1.97.3.7.6 | TablesifUtilPortPeakTable | not-accessible | mandatory | A list of interface utilization entries; one per sifUtilCount per physical port, plus one per physical port for the most recently completed samples. |
| 1.3.6.1.4.1.97.3.7.6.1 | RowsifUtilPortPeakEntry | not-accessible | mandatory | A set of utilization statistics recorded for an interface entry at per-port throughput peaks. |
| 1.3.6.1.4.1.97.3.7.6.1.1 | ColumnsifUtilPortPeakIndex | read-only | mandatory | The port number. |
| 1.3.6.1.4.1.97.3.7.6.1.2 | ColumnsifUtilPortPeakOrdinal | read-only | mandatory | The ordinal of the entry, with 1 representing 'Now' (i.e. the sample most recently accumulated), with 2 representing the sample taken at the highest per-port t… |
| 1.3.6.1.4.1.97.3.7.6.1.3 | ColumnsifUtilPortPeakBRTimestamp | read-only | mandatory | The value of sysUpTime associated with the end of the sample period for the associated sifUtilPortPeakTBitRate/sifUtilPortPeakRBitRate sample, or the most rece… |
| 1.3.6.1.4.1.97.3.7.6.1.4 | ColumnsifUtilPortPeakTBitRate | read-only | mandatory | The ratio of the number of bits transmitted per second during the per-physical-port sample interval to the linespeed in bits per second, expressed in integer u… |
| 1.3.6.1.4.1.97.3.7.6.1.5 | ColumnsifUtilPortPeakRBitRate | read-only | mandatory | The ratio of the number of bits received per second during the per-physical-port sample interval to the linespeed in bits per second, expressed in integer unit… |
| 1.3.6.1.4.1.97.3.7.7 | ScalarsifUtilSysPeakReset | read-write | mandatory | This object is set to true (1) to erase earlier per-system utilization samples. |
| 1.3.6.1.4.1.97.3.7.8 | TablesifUtilSysPeakTable | not-accessible | mandatory | A list of interface utilization entries; one per sifUtilCount per physical port, plus one per physical port for the most recently completed samples. |
| 1.3.6.1.4.1.97.3.7.8.1 | RowsifUtilSysPeakEntry | not-accessible | mandatory | A set of utilization statistics recorded for an interface entry at overall system throughput peaks. |
| 1.3.6.1.4.1.97.3.7.8.1.1 | ColumnsifUtilSysPeakIndex | read-only | mandatory | The port number. |
| 1.3.6.1.4.1.97.3.7.8.1.2 | ColumnsifUtilSysPeakOrdinal | read-only | mandatory | The ordinal of the entry, with 1 representing 'Now' (i.e. the sample most recently accumulated), with 2 representing the sample taken at the highest peak syste… |
| 1.3.6.1.4.1.97.3.7.8.1.3 | ColumnsifUtilSysPeakTimestamp | read-only | mandatory | The value of sysUpTime associated with the end of the sample period for the associated sifUtilSysPeakTBitRate/sifUtilSysPeakRBitRate sample, or the most recent… |
| 1.3.6.1.4.1.97.3.7.8.1.4 | ColumnsifUtilSysPeakTBitRate | read-only | mandatory | The ratio of the number of bits transmitted per second during the per-system-peak sample interval to the linespeed in bits per second, expressed in integer uni… |
| 1.3.6.1.4.1.97.3.7.8.1.5 | ColumnsifUtilSysPeakRBitRate | read-only | mandatory | The ratio of the number of bits received per second during the per-system-peak sample interval to the linespeed in bits per second, expressed in integer units … |
| 1.3.6.1.4.1.97.3.8 | Nodesfddi | |||
| 1.3.6.1.4.1.97.3.8.1 | TablesfddiTable | not-accessible | mandatory | A list of interface entries; one per FDDI port. |
| 1.3.6.1.4.1.97.3.8.1.1 | RowsfddiEntry | not-accessible | mandatory | A set of objects for an interface entry. |
| 1.3.6.1.4.1.97.3.8.1.1.1 | ColumnsfddiIndex | read-only | mandatory | The ES/1's port number of the port. |
| 1.3.6.1.4.1.97.3.8.1.1.2 | ColumnsfddiRxHwAborts | read-write | mandatory | The number of packets that were discarded due to receive abort errors. |
| 1.3.6.1.4.1.97.3.8.1.1.3 | ColumnsfddiRxParitys | read-write | mandatory | The number of packets that were discarded due to parity errors. |
| 1.3.6.1.4.1.97.3.8.1.1.4 | ColumnsfddiRxShorts | read-write | mandatory | The number of packets that were discarded because they were too short. |
| 1.3.6.1.4.1.97.3.8.1.1.5 | ColumnsfddiDpcErrCnts | read-write | mandatory | The number of DPC errors. |
| 1.3.6.1.4.1.97.3.8.1.1.6 | ColumnsfddiDpcErrValue | read-write | mandatory | Detailed status of the last DPC error. |
| 1.3.6.1.4.1.97.3.8.1.1.7 | ColumnsfddiRbcErrCnts | read-write | mandatory | The number of RBC errors. |
| 1.3.6.1.4.1.97.3.8.1.1.8 | ColumnsfddiRbcErrValue | read-write | mandatory | Detailed status of the last RBC error. (FIOM MIB only) |
| 1.3.6.1.4.1.97.3.8.1.1.9 | ColumnsfddiTxAsync | read-write | mandatory | Number of bytes to reserve in the DPC Buffer Memory for transmitting asynchronous packets. |
| 1.3.6.1.4.1.97.3.8.1.1.10 | ColumnsfddiShortAddressing | read-only | mandatory | Whether any packets were received with 16 bit MAC addresses. |
| 1.3.6.1.4.1.97.3.8.1.1.11 | ColumnsfddiSmtConditions | read-write | mandatory | SMT conditions which should be reported to the NMS via SNMP Traps. Possible values are any combination of the following bits: ring = 0x00000001, claim = 0x0000… |
| 1.3.6.1.4.1.97.3.8.1.1.12 | ColumnsfddiSrfConditions | read-write | mandatory | SRF conditions which should be reported to the NMS via SNMP Traps. Possible values are any combination of the following bits: srf-frame-error = 0x00000001, srf… |
| 1.3.6.1.4.1.97.3.8.1.1.13 | ColumnsfddiSmtConditionsStatus | read-write | mandatory | Requested SMT conditions which are currently present. Writing to sfddiSmtConditionsStatus is used to acknowledge the SNMP traps. |
| 1.3.6.1.4.1.97.3.8.1.1.14 | ColumnsfddiSrfConditionsStatus | read-write | mandatory | Requested SRF conditions which are currently present. Writing to sfddiSrfConditionsStatus is used to acknowledge the SNMP traps. |
| 1.3.6.1.4.1.97.3.8.1.1.15 | ColumnsfddiSrfReportLimit | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.8.1.1.16 | ColumnsfddiFrameErrorThreshold | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.8.1.1.17 | ColumnsfddiNotCopiedThreshold | read-write | mandatory | Value for the fddiMACNotCopiedThreshold variable. |
| 1.3.6.1.4.1.97.3.8.1.1.18 | ColumnsfddiSBFlag | read-only | mandatory | Whether the ECM's optical bypass is stuck, i.e., the current value of the SMT SB_Flag variable. |
| 1.3.6.1.4.1.97.3.8.1.1.19 | ColumnsfddiRxEbits | read-only | mandatory | The number of packets that were discarded because another station had already set the E bit. |
| 1.3.6.1.4.1.97.3.8.1.1.20 | ColumnsfddiOBSFuseBad | read-only | mandatory | Whether the fuse to the FDDI port's optical bypass is bad. |
| 1.3.6.1.4.1.97.3.8.1.1.21 | ColumnsfddiThruB | read-write | mandatory | Whether to connect to the FDDI port B (not applicable for SAS). |
| 1.3.6.1.4.1.97.3.8.1.1.22 | ColumnsfddiStationDescriptor | read-only | mandatory | A four byte string containing the FDDI port's Station Descriptor parameter, as defined by the SMT frame protocols. |
| 1.3.6.1.4.1.97.3.8.1.1.23 | ColumnsfddiStationState | read-only | mandatory | A four byte string containing the FDDI port's Station State parameter, as defined by the SMT frame protocols. |
| 1.3.6.1.4.1.97.3.8.1.1.24 | ColumnsfddiDownstreamNbr | read-only | mandatory | The MAC address of the FDDI port's downstream neighbor. |
| 1.3.6.1.4.1.97.3.8.1.1.25 | ColumnsfddiSMTBufferSize | read-write | mandatory | The amount of packet buffer space to reserve for processing SMT frames. Possible values 9000 - 18000. (FIOM MIB only) |
| 1.3.6.1.4.1.97.3.9 | Nodesuart | |||
| 1.3.6.1.4.1.97.3.9.1 | TablesuartTable | not-accessible | mandatory | A list of interface entries; one per UART port. |
| 1.3.6.1.4.1.97.3.9.1.1 | RowsuartEntry | not-accessible | mandatory | A set of objects for an interface entry. |
| 1.3.6.1.4.1.97.3.9.1.1.1 | ColumnsuartIndex | read-only | mandatory | The ES/1's port number of the port. |
| 1.3.6.1.4.1.97.3.9.1.1.2 | ColumnsuartBaud | read-write | mandatory | This is the desired baud rate. Only 1200 baud through 19,200 baud are supported by the ES/1. |
| 1.3.6.1.4.1.97.3.9.1.1.3 | ColumnsuartModem | read-write | mandatory | The expected modem signals; definitions of the different values are TBD. |
| 1.3.6.1.4.1.97.3.9.1.1.4 | ColumnsuartIpNeighborAddress | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.9.1.1.5 | ColumnsuartPPPActive | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.9.1.1.6 | ColumnsuartAlignmentErrors | read-only | mandatory | Number of received packets with frame alignment errors, since the port was last enabled. |
| 1.3.6.1.4.1.97.3.9.1.1.7 | ColumnsuartOverrunErrors | read-only | mandatory | Number of received packets with data overrun errors, since the port was last enabled. |
| 1.3.6.1.4.1.97.3.10 | Nodefilter | |||
| 1.3.6.1.4.1.97.3.10.1 | ScalarfilterMaxCount | read-only | mandatory | The maximum number of combination filters that may be defined for the ES/1. This is always 100. |
| 1.3.6.1.4.1.97.3.10.2 | ScalarfilterCurrentCount | read-only | mandatory | The number of combination filters currently defined for the ES/1. |
| 1.3.6.1.4.1.97.3.10.3 | ScalarfilterDeleteID | read-write | mandatory | A filter identifier used for deleting filters. After the NMS sets this field, the ES/1 deletes the filterEntry that has a matching filter ID field, and resets … |
| 1.3.6.1.4.1.97.3.10.4 | ScalarfilterNextID | read-only | mandatory | A filter identifier used for adding filters. |
| 1.3.6.1.4.1.97.3.10.5 | ScalarfilterAddID | read-write | mandatory | A filter identifier used for adding filters. After the NMS sets this field, the ES/1 adds the filterEntry indexed by filterAddIndex. The ES/1 then updates filt… |
| 1.3.6.1.4.1.97.3.10.6 | ScalarfilterAddIndex | read-write | mandatory | The index within filterTable, after which a filter should be added. If filterAddIndex contains zero, then the filter should be added as the first filterEntry w… |
| 1.3.6.1.4.1.97.3.10.7 | TablefilterTable | not-accessible | mandatory | A list of combination filters; one per defined filter. If fewer than filterMaxCount filters have been defined, then an additional filterEntry exists, which is … |
| 1.3.6.1.4.1.97.3.10.7.1 | RowfilterEntry | not-accessible | mandatory | A set of objects for a combination filter. |
| 1.3.6.1.4.1.97.3.10.7.1.1 | ColumnfilterIndex | read-only | mandatory | This number always matches the instance of the filterEntry. |
| 1.3.6.1.4.1.97.3.10.7.1.2 | ColumnfilterID | read-only | mandatory | Identifier assigned to the filter, used for obtaining the value for filterDeleteID so that the filter can be deleted. |
| 1.3.6.1.4.1.97.3.10.7.1.3 | ColumnfilterPortNo | read-write | mandatory | The port number related to this filter. |
| 1.3.6.1.4.1.97.3.10.7.1.4 | ColumnfilterComboType | read-write | mandatory | Whether this is an entry filter (0), an exit filter(1), a port mirror entry filter (3), or a port mirror exit filter (4). |
| 1.3.6.1.4.1.97.3.10.7.1.5 | ColumnfilterFlags | read-write | mandatory | A set of flag bits which control the operation of the filter. Filters will not prevent packets from being accepted by the ES/1 as a final destination. The foll… |
| 1.3.6.1.4.1.97.3.10.7.1.6 | ColumnfilterFrame | read-write | mandatory | Ethernet protocol type (1501-65535), or one (1) to indicate any 802 frame, or two (2) to indicate any Ethernet frame, Note that a specific Ethernet protocol ty… |
| 1.3.6.1.4.1.97.3.10.7.1.7 | ColumnfilterSource | read-write | mandatory | Beginning source address. |
| 1.3.6.1.4.1.97.3.10.7.1.8 | ColumnfilterSourceEnd | read-write | mandatory | Ending source address. |
| 1.3.6.1.4.1.97.3.10.7.1.9 | ColumnfilterDest | read-write | mandatory | Beginning destination address. |
| 1.3.6.1.4.1.97.3.10.7.1.10 | ColumnfilterDestEnd | read-write | mandatory | Ending destination address. |
| 1.3.6.1.4.1.97.3.10.7.1.11 | ColumnfilterSourceMask | read-write | mandatory | A bitmask to be applied to the packet's source address before checking it against filterSource and filterSourceEnd. |
| 1.3.6.1.4.1.97.3.10.7.1.12 | ColumnfilterDestMask | read-write | mandatory | A bitmask to be applied to the packet's destination address before checking it against filterDest and filterDestEnd. |
| 1.3.6.1.4.1.97.3.10.7.1.13 | ColumnfilterSrcLan | read-write | mandatory | Either the port number from which the packet is received, or the value of any one of the group identifiers defined by sifLan for that port. |
| 1.3.6.1.4.1.97.3.10.7.1.14 | ColumnfilterOffset | read-write | mandatory | Zero-based offset of an arbitrary field within the packet. Depending upon the value of filterFlags, the offset is relative to the start of the translated packe… |
| 1.3.6.1.4.1.97.3.10.7.1.15 | ColumnfilterField | read-write | mandatory | An 8 octet value to be compared to the contents of the arbitrary field within the packet. |
| 1.3.6.1.4.1.97.3.10.7.1.16 | ColumnfilterMask | read-write | mandatory | An 8 octet mask to be applied to the arbitrary field within the packet, before comparing it to filterField. |
| 1.3.6.1.4.1.97.3.10.7.1.17 | ColumnfilterThreshold | read-write | mandatory | The number of filter invocations at which an alarm to the NMS should be generated. |
| 1.3.6.1.4.1.97.3.10.7.1.18 | ColumnfilterThreshTime | read-write | mandatory | The length of time, in seconds, to which filterThreshold applies. A value of zero indicates that no alarms should be sent to the NMS. Values greater than 3600 … |
| 1.3.6.1.4.1.97.3.10.7.1.19 | ColumnfilterThreshFlag | read-only | mandatory | Whether usage of this filter has exceeded the limits specified by filterThreshold and filterThreshTime, and the NMS has not yet acknowledged the alarm. Therefo… |
| 1.3.6.1.4.1.97.3.10.7.1.20 | ColumnfilterPktCnts | read-only | mandatory | The total number of packets which were discarded due to this filter. |
| 1.3.6.1.4.1.97.3.10.7.1.21 | ColumnfilterLastSrc | read-only | mandatory | The source MAC address of the last packet which was discarded due to this filter |
| 1.3.6.1.4.1.97.3.11 | Nodereboot | |||
| 1.3.6.1.4.1.97.3.11.1 | ScalarrebootBridgingMemory | read-write | mandatory | The percentage (1 - 99) of the PPE's memory to be allocated for MAC bridging. The PPE's remaining memory will be used for communicating with the NMS and for ro… |
| 1.3.6.1.4.1.97.3.11.2 | TablerebootSlotTable | not-accessible | mandatory | A list of the desired occupants of the slots; one per slot. |
| 1.3.6.1.4.1.97.3.11.2.1 | RowrebootEntry | not-accessible | mandatory | A set of objects for each slot. |
| 1.3.6.1.4.1.97.3.11.2.1.1 | ColumnrebootIndex | read-only | mandatory | The slot number, beginning with 1 for the first slot. This number always matches the instance of the rebootEntry. |
| 1.3.6.1.4.1.97.3.11.2.1.2 | ColumnrebootType | read-write | mandatory | The desired module type of the slot. |
| 1.3.6.1.4.1.97.3.11.2.1.3 | ColumnrebootUseMod | read-write | mandatory | Whether to use this module, not applicable for the Packet Processing Engine. |
| 1.3.6.1.4.1.97.3.11.2.1.4 | ColumnrebootPortType | read-write | mandatory | This is a variable-length byte array where each element represents the types of the ports belonging to this module. |
| 1.3.6.1.4.1.97.3.11.3 | ScalarrebootConfig | read-write | mandatory | The configuration file that will be used when the ES/1 reboots. This parameter is normally automatically set by the ES/1; however, an NMS may explicitly set it… |
| 1.3.6.1.4.1.97.3.11.4 | ScalarrebootRouteMemory | read-write | mandatory | Percentage of non-bridging memory to allocate for routing tables. The remainder will be used for transient packets such as ARP and RIP. |
| 1.3.6.1.4.1.97.3.12 | Nodedebug | |||
| 1.3.6.1.4.1.97.3.12.1 | ScalardebugStringID | read-only | mandatory | The number of debug text strings sent by the ES/1. This parameter is used by the ES/1's enterprise specific trap mechanism. |
| 1.3.6.1.4.1.97.3.12.2 | ScalardebugString | read-only | mandatory | The last debug text string (0-80 bytes) sent by the ES/1. |
| 1.3.6.1.4.1.97.3.12.3 | TabledebugTable | not-accessible | mandatory | A list of the modules which may be debugged, with one module per slot defined by hwSlotTable. |
| 1.3.6.1.4.1.97.3.12.3.1 | RowdebugEntry | not-accessible | mandatory | A set of objects for each module. |
| 1.3.6.1.4.1.97.3.12.3.1.1 | ColumndebugIndex | read-only | mandatory | The module number, beginning with 1 for the module in the first slot. This number always matches the instance of the debugEntry. |
| 1.3.6.1.4.1.97.3.12.3.1.2 | ColumndebugOperation | read-write | mandatory | Type of debug operation requested. |
| 1.3.6.1.4.1.97.3.12.3.1.3 | ColumndebugBase | read-write | mandatory | The base address of the memory region to be examined or modified. |
| 1.3.6.1.4.1.97.3.12.3.1.4 | ColumndebugLength | read-write | mandatory | The desired length, in words, of the memory region to be examined or modified. After the ES/1 performs the operation, debugLength is updated to indicate the le… |
| 1.3.6.1.4.1.97.3.12.3.1.5 | ColumndebugData | read-write | mandatory | A series of 0-64 octets, which represents 0-16 words (this may change in the future, if the ES/1 has processors with word sizes of other than 4 bytes per word)… |
| 1.3.6.1.4.1.97.3.13 | Nodelpbk | |||
| 1.3.6.1.4.1.97.3.13.1 | TablelpbkTable | not-accessible | mandatory | A list of interface entries; one per port. |
| 1.3.6.1.4.1.97.3.13.1.1 | RowlpbkEntry | not-accessible | mandatory | A set of objects for an interface entry. |
| 1.3.6.1.4.1.97.3.13.1.1.1 | ColumnlpbkIndex | read-only | mandatory | The port number, beginning with 1 for the first port. |
| 1.3.6.1.4.1.97.3.13.1.1.2 | ColumnlpbkOperation | read-write | mandatory | The type of loopback being performed. Setting lpbkOperation to loopback-off causes loop back operation to terminate. Setting lpbkOperation to loopback-local or… |
| 1.3.6.1.4.1.97.3.13.1.1.3 | ColumnlpbkDestAddr | read-write | mandatory | The MAC address of the target device, only needed for remote loopback. |
| 1.3.6.1.4.1.97.3.13.1.1.4 | ColumnlpbkPktNum | read-write | mandatory | The number of loopback packets to be transmitted. |
| 1.3.6.1.4.1.97.3.13.1.1.5 | ColumnlpbkInterval | read-write | mandatory | The desired time delay between the reception of a looped back packet, and the transmission of the next packet to be looped back. |
| 1.3.6.1.4.1.97.3.13.1.1.6 | ColumnlpbkPktLength | read-write | mandatory | The length (in octets) of the loopback packet. The values of the data itself are automatically selected by the ES/1. |
| 1.3.6.1.4.1.97.3.13.1.1.7 | ColumnlpbkIncrements | read-write | mandatory | The number of bytes of data to be added to the loopback packet after each successful loopback packet transmission and reception. When the port's maximum packet… |
| 1.3.6.1.4.1.97.3.13.1.1.8 | ColumnlpbkGoods | read-only | mandatory | The number of packets successfully looped back. This number is automatically reset to zero, whenever loopback operation is initiated. |
| 1.3.6.1.4.1.97.3.13.1.1.9 | ColumnlpbkErrorNoReceives | read-only | mandatory | The number of packets which were transmitted, but not received. This number is automatically reset to zero, whenever loopback operation is initiated. |
| 1.3.6.1.4.1.97.3.13.1.1.10 | ColumnlpbkErrorBadReceives | read-only | mandatory | The number of transmitted packets which were received with different data patterns. This number is automatically reset to zero, whenever loopback operation is … |
| 1.3.6.1.4.1.97.3.13.1.1.11 | ColumnlpbkErrorSize | read-only | mandatory | The length of the last loopback packet which caused either lpbkErrorNoReceives or lpbkErrorBadReceives to be incremented. This number is automatically reset to… |
| 1.3.6.1.4.1.97.3.13.1.1.12 | ColumnlpbkErrorSent | read-only | mandatory | The transmitted bytes (0-4) of data within the last loopback packet which caused lpbkErrorBadReceives to be incremented. This parameter is automatically reset … |
| 1.3.6.1.4.1.97.3.13.1.1.13 | ColumnlpbkErrorReceived | read-only | mandatory | The received bytes (0-4) of data within the last loopback packet which caused lpbkErrorBadReceives to be incremented. This parameter is automatically reset to … |
| 1.3.6.1.4.1.97.3.13.1.1.14 | ColumnlpbkErrorOffset | read-only | mandatory | The byte offset (one being the first byte) within the loopback packet where lpbkErrorSent begins. This number is automatically reset to zero, whenever loopback… |
| 1.3.6.1.4.1.97.3.14 | Nodeswan | |||
| 1.3.6.1.4.1.97.3.14.1 | TableswanTable | not-accessible | mandatory | A list of interface entries; one per WAN port. |
| 1.3.6.1.4.1.97.3.14.1.1 | RowswanEntry | not-accessible | mandatory | A set of objects for an interface entry. |
| 1.3.6.1.4.1.97.3.14.1.1.1 | ColumnswanIndex | read-only | mandatory | The ES/1's port number of the port. |
| 1.3.6.1.4.1.97.3.14.1.1.2 | ColumnswanDesiredSpeed | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.14.1.1.3 | ColumnswanActualSpeed | read-only | mandatory | This is the actual line speed. The possible values are defined by suartSpeed. For HSSI, the speed is 45-megabits(11). If the RS-449 interface is being used on … |
| 1.3.6.1.4.1.97.3.14.1.1.4 | ColumnswanIpNeighborAddress | read-write | mandatory | Zero, or an IP address to assign to the port's neighbor. |
| 1.3.6.1.4.1.97.3.14.1.1.5 | ColumnswanPPPActive | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.14.1.1.6 | ColumnswanAlignmentErrors | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.14.1.1.7 | ColumnswanOverrunErrors | read-only | mandatory | Number of received packets with data overrun errors, since the port was last enabled. |
| 1.3.6.1.4.1.97.3.14.1.1.8 | ColumnswanPortType | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.14.1.1.9 | ColumnswanLinkCost | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.14.1.1.10 | ColumnswanMeshState | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.14.1.1.11 | ColumnswanLinkSubnet | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.14.1.1.12 | ColumnswanLinkBridge | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.14.1.1.13 | ColumnswanLinkPort | read-only | mandatory | |
| 1.3.6.1.4.1.97.3.14.1.1.14 | ColumnswanNegotiate | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.14.1.1.15 | ColumnswanSwitches | read-write | mandatory | Current port selected. |
| 1.3.6.1.4.1.97.3.14.1.1.16 | ColumnswanDCEDrops | read-only | mandatory | Number of instances when loss of DCE has been detected. |
| 1.3.6.1.4.1.97.3.14.1.1.17 | ColumnswanOutPacketType | read-write | mandatory | The type of out going packet to generate on the HSSI link. |
| 1.3.6.1.4.1.97.3.14.1.1.18 | ColumnswanLinkErrorPercentage | read-write | mandatory | The percentage of acceptible errors in hundreths of percent. |
| 1.3.6.1.4.1.97.3.14.1.1.19 | ColumnswanLinkErrorDuration | read-write | mandatory | The time period in hundredths of a second over which the error percentage should be applied. |
| 1.3.6.1.4.1.97.3.14.1.1.20 | ColumnswanLinkErrorFailPeriods | read-write | mandatory | The maximum number of periods allowed to contain the error percentage before the link quality is determined to have failed. |
| 1.3.6.1.4.1.97.3.14.1.1.21 | ColumnswanLinkErrorMaxPeriods | read-write | mandatory | The maximum number of periods to be used for calculation of link quality. Default is 10. |
| 1.3.6.1.4.1.97.3.14.1.1.22 | ColumnswanLinkRestartTime | read-write | mandatory | The time period in centiseconds which must contain error free LQR operation before restarting link. |
| 1.3.6.1.4.1.97.3.14.1.1.23 | ColumnswanPreserveFCS | read-write | mandatory | Preserve received FCS if true, else regenerate FCS on packet transmission. |
| 1.3.6.1.4.1.97.3.16 | Nodesrepeater | |||
| 1.3.6.1.4.1.97.3.16.1 | TablesrepeaterTable | not-accessible | mandatory | SMC-specific status information and control variables for a collection of repeater groups in a particular system. |
| 1.3.6.1.4.1.97.3.16.1.1 | RowsrepeaterEntry | not-accessible | mandatory | SMC-specific status information and control variables for a particular repeater domain (group) in the system. |
| 1.3.6.1.4.1.97.3.16.1.1.1 | ColumnsrepeaterGroupID | read-only | mandatory | The value of srepeaterGroupID is assigned so as to uniquely identify a repeater domain (group) in a system where a single agent manages multiple repeater domai… |
| 1.3.6.1.4.1.97.3.16.1.1.2 | ColumnsrepeaterLinkStatusMask | read-only | mandatory | This mask provides quick access to the general connectivity of the repeater. Each bit corresponds to the link status of a repeater port. If the bit is set to 1… |
| 1.3.6.1.4.1.97.3.16.1.1.3 | ColumnsrepeaterExtendedStats | read-write | mandatory | When enabled(1), the rptrMonitorGroup, rptrMonitorPort, and rptrAddrTrack tables are available, and the CEIOM maintains frame-by-frame tallies for the repeater… |
| 1.3.6.1.4.1.97.3.16.2 | TablesrepeaterPortTable | not-accessible | mandatory | SMC-specific status information and control variables for a collection of repeater ports in a particular system. |
| 1.3.6.1.4.1.97.3.16.2.1 | RowsrepeaterPortEntry | not-accessible | mandatory | SMC-specific status information and control variables for a particular repeater port in the system. |
| 1.3.6.1.4.1.97.3.16.2.1.1 | ColumnsrepeaterPortGroupID | read-only | mandatory | The value of srepeaterPortGroupID is assigned so as to uniquely identify a group (repeater ID) in a system where a single agent manages multiple repeater group… |
| 1.3.6.1.4.1.97.3.16.2.1.2 | ColumnsrepeaterPortPortID | read-only | mandatory | Identifies a repeater port within a repeater group/domain. Values correspond to physical connector position on the CEIOM. For the CEIOM-24, the leftmost positi… |
| 1.3.6.1.4.1.97.3.16.2.1.3 | ColumnsrepeaterPortLinkPulse | read-write | mandatory | When enabled (the default), the repeater port generates and expects to receive a link pulse, as per 10BaseT specification. When disabled, the port does not gen… |
| 1.3.6.1.4.1.97.3.17 | Nodesproto | |||
| 1.3.6.1.4.1.97.3.17.1 | TablesprotoTable | not-accessible | mandatory | This table contains configuration information specifying the types of protocols used to bridge, route, translate, and filter frames for each port. |
| 1.3.6.1.4.1.97.3.17.1.1 | RowsprotoEntry | not-accessible | mandatory | Each entry in this table specifies which protocols are used by a particular port in the ES/1. |
| 1.3.6.1.4.1.97.3.17.1.1.1 | ColumnsprotoIfIndex | read-only | mandatory | Identifies the interface (port) to which this entry's information belongs. The value of this variable corresponds to ifIndex, as well as most of the other port… |
| 1.3.6.1.4.1.97.3.17.1.1.2 | ColumnsprotoBridge | read-write | mandatory | Defines the bridging method to be applied to frames received at, or destined for, this port. Ethernet and FDDI ports may be configured for transparent, srt, or… |
| 1.3.6.1.4.1.97.3.17.1.1.3 | ColumnsprotoSuppressBpdus | read-write | mandatory | Allows transmission of spanning tree protocol packets to be suppressed. If normal(1), 802.1d spanning tree packets and source-routing spanning tree packets are… |
| 1.3.6.1.4.1.97.3.17.1.1.4 | ColumnsprotoIpRoute | read-write | mandatory | Specifies whether or not this port is to be used for IP routing. |
| 1.3.6.1.4.1.97.3.17.1.1.5 | ColumnsprotoIpxRoute | read-write | mandatory | Specifies whether or not this port is to be used for Novell NetWare IPX routing. |
| 1.3.6.1.4.1.97.3.17.1.1.6 | ColumnsprotoAppleRoute | read-write | mandatory | Specifies whether or not this port is to be used for AppleTalk (tm) routing. |
| 1.3.6.1.4.1.97.3.17.1.1.7 | ColumnsprotoArpTranslate | read-write | mandatory | These options are intended to compensate for any like- ly implementation of internet ARP on 802.5 token ring. If set to bitswap1(2), then embedded MAC addresse… |
| 1.3.6.1.4.1.97.3.17.1.1.8 | ColumnsprotoArpSourceRoute | read-write | mandatory | Specifies whether, when bridging TCP/IP ARP packets which are source-routing explorer frames, the routing information is to be stripped or propagated. If pass-… |
| 1.3.6.1.4.1.97.3.17.1.1.9 | ColumnsprotoIpxTranslate | read-write | mandatory | Specifies whether, when bridging Novell IPX frames, they are to be translated to Ethernet-like frame for- mat. This option applies only to token ring ports. |
| 1.3.6.1.4.1.97.3.17.1.1.10 | ColumnsprotoAppleTranslate | read-write | mandatory | Specifies whether, when bridging AppleTalk ELAP, TLAP, and AARP frames, those frames are to be translated between token ring and Ethernet format before being f… |
| 1.3.6.1.4.1.97.3.17.1.1.11 | ColumnsprotoIbmLlcTranslate | read-write | mandatory | Specifies whether, when bridging IBM LLC frames, an 8209-style translation between token ring and Ethernet format is to be performed before being forwarded. Th… |
| 1.3.6.1.4.1.97.3.17.1.1.12 | ColumnsprotoRip | read-write | mandatory | Specifies whether the internet Routing Information Protocol (RFC-1058) is to be used over this port. Only valid if sprotoIpRoute is enabled. |
| 1.3.6.1.4.1.97.3.17.1.1.13 | ColumnsprotoEgp | read-write | mandatory | Specifies whether the internet External Gateway Proto- col (RFC-904) is to be used over this port. Only valid if sprotoIpRoute is enabled. |
| 1.3.6.1.4.1.97.3.17.1.1.14 | ColumnsprotoOspf | read-write | mandatory | Specifies whether the internet Open Shortest Path First protocol (RFC-1247) is to be used over this port. Only valid if sprotoIpRoute is enabled. |
| 1.3.6.1.4.1.97.3.17.1.1.15 | ColumnsprotoArpProxy | read-write | mandatory | Specifies whether the port is to respond to internet ARP requests for which the unit is the next hop in a routed path. Only valid if sprotoIpRoute is enabled. |
| 1.3.6.1.4.1.97.3.17.1.1.16 | ColumnsprotoIbm8209Lsaps | read-write | mandatory | Specifies up to eight LSAPs for which IBM 8209-style token-ring-to-Ethernet encapsulation is to be performed. Only valid if sprotoIbmLLcTranslate is enabled. T… |
| 1.3.6.1.4.1.97.3.17.1.1.17 | ColumnsprotoBootpRelay | read-write | mandatory | Specifies whether or not this port is to relay BOOTP packets, as described in RFC-951 and subsequent internet-drafts. Only valid if IP routing is also enabled … |
| 1.3.6.1.4.1.97.3.17.1.1.18 | ColumnsprotoNetbiosTranslate | read-write | mandatory | Specifies whether, when bridging Netbios packets which are source-routing explorer frames, the routing information is to be stripped or propagated. If pass- Ri… |
| 1.3.6.1.4.1.97.3.17.1.1.19 | ColumnsprotoIpMulticast | read-write | mandatory | Specifies whether the internet Multicast Routing Protocol (RFC-1075) is to be used over this port. Only valid if sprotoIpRoute is enabled. |
| 1.3.6.1.4.1.97.3.17.1.1.20 | ColumnsprotoTrunking | read-write | mandatory | Specifies whether SMC's trunking protocol (an extension to the standard Spanning Tree) is to be used over this port. |
| 1.3.6.1.4.1.97.3.17.1.1.22 | ColumnsprotoIpxSrTranslate | read-write | mandatory | Specifies whether, when bridging IPX packets which are source-routing explorer frames, the routing information is to be stripped or propagated. If pass- Rif(1)… |
| 1.3.6.1.4.1.97.3.17.1.1.23 | ColumnsprotoAllTranslate | read-write | mandatory | Specifies whether, when bridging any source-routed explorer frames, the routing information is to be stripped or propagated. If passRif(1), the frame is bridge… |
| 1.3.6.1.4.1.97.3.17.1.1.24 | ColumnsprotoSteHopCountAppliedRule | read-write | mandatory | hopcountnotapplied(1), STE hop count rules are not applied to STE frames. Default for SR ports. Follows IBM's specifications. hopcountapplied(2), STE hop count… |
| 1.3.6.1.4.1.97.3.17.2 | ScalarsprotoIpxDot3Framing | read-write | mandatory | If sprotoIpxRoute or sprotoIpxTranslate is enabled, specifies the type of framing to be used for NetWare IPX packets on 802.3 networks. ethernet8023(1) speci- … |
| 1.3.6.1.4.1.97.3.18 | Nodesipx | |||
| 1.3.6.1.4.1.97.3.18.1 | TablesipxIfTable | not-accessible | mandatory | Describes per-interface attributes of IPX routing. |
| 1.3.6.1.4.1.97.3.18.1.1 | RowsipxIfEntry | not-accessible | mandatory | For a particular interface, defines the IPX routing information. |
| 1.3.6.1.4.1.97.3.18.1.1.1 | ColumnsipxIfIndex | read-only | mandatory | Used to index through the interfaces (ports) on the ES/1, when used as an IPX router. Identical to ifIndex. Entries exist for all external interfaces, whether … |
| 1.3.6.1.4.1.97.3.18.1.1.2 | ColumnsipxIfNetwork | read-write | mandatory | The IPX network number associated with this interface. |
| 1.3.6.1.4.1.97.3.18.1.1.3 | ColumnsipxIfFraming | read-write | mandatory | Defines the link-level framing to be used for this interface. Options 1-4 are available for Ethernet; options 3 and 4 are valid for token ring; options 3-5 are… |
| 1.3.6.1.4.1.97.3.18.1.1.4 | ColumnsipxIfInRipPkts | read-only | mandatory | Number of IPX Routing Information Protocol packets received on this interface. |
| 1.3.6.1.4.1.97.3.18.1.1.5 | ColumnsipxIfOutRipPkts | read-only | mandatory | Number of IPX Routing Information Protocol packets transmitted on this interface. |
| 1.3.6.1.4.1.97.3.18.1.1.6 | ColumnsipxIfInSapPkts | read-only | mandatory | Number of IPX Service Advertising Protocol packets received on this interface. |
| 1.3.6.1.4.1.97.3.18.1.1.7 | ColumnsipxIfOutSapPkts | read-only | mandatory | Number of IPX Service Advertising Protocol packets transmitted on this interface. |
| 1.3.6.1.4.1.97.3.18.2 | TablesipxRouteTable | not-accessible | mandatory | This router's IPX Routing table. |
| 1.3.6.1.4.1.97.3.18.2.1 | RowsipxRouteEntry | not-accessible | mandatory | A route to a particular destination. |
| 1.3.6.1.4.1.97.3.18.2.1.1 | ColumnsipxRouteDest | read-only | mandatory | The destination network address of this route. |
| 1.3.6.1.4.1.97.3.18.2.1.2 | ColumnsipxRouteIfIndex | read-only | mandatory | The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particu… |
| 1.3.6.1.4.1.97.3.18.2.1.3 | ColumnsipxRouteTickCount | read-only | mandatory | The primary routing metric for this route, which is an estimate of the number of 55 millisecond ticks that are needed to reach the destination. |
| 1.3.6.1.4.1.97.3.18.2.1.4 | ColumnsipxRouteHopCount | read-only | mandatory | The secondary routing metric for this route, which is the number of routers that must be traversed to reach the destination. |
| 1.3.6.1.4.1.97.3.18.2.1.5 | ColumnsipxRouteNextHop | read-only | mandatory | The IPX node address of the next hop of this route, if indirect. If direct, the address of the local interface. |
| 1.3.6.1.4.1.97.3.18.2.1.6 | ColumnsipxRouteAge | read-only | mandatory | The number of seconds since this route was last updated. |
| 1.3.6.1.4.1.97.3.18.3 | TablesipxSapTable | not-accessible | mandatory | This router's IPX service advertising cache table. |
| 1.3.6.1.4.1.97.3.18.3.1 | RowsipxSapEntry | not-accessible | mandatory | An IPX service definition, as advertised by the SAP protocol and distributed through the SAP cache of this router. |
| 1.3.6.1.4.1.97.3.18.3.1.1 | ColumnsipxSapIndex | read-only | mandatory | Used only as an artificial index to this table. Has no independent meaning. |
| 1.3.6.1.4.1.97.3.18.3.1.2 | ColumnsipxSapType | read-only | mandatory | Identifies the type of service provided by the server. Values range 0..ffff, and are defined by Novell. |
| 1.3.6.1.4.1.97.3.18.3.1.3 | ColumnsipxSapName | read-only | mandatory | Server Name. |
| 1.3.6.1.4.1.97.3.18.3.1.4 | ColumnsipxSapNetwork | read-only | mandatory | The IPX network address of the server providing the indicated service. |
| 1.3.6.1.4.1.97.3.18.3.1.5 | ColumnsipxSapNodeId | read-only | mandatory | The IPX node address of the server. With NetWare 2.x, this corresponds to a physical MAC address, represented here in canonical (little-endian) bit order. With… |
| 1.3.6.1.4.1.97.3.18.3.1.6 | ColumnsipxSapSocket | read-only | mandatory | The socket number to which service requests should be addressed. |
| 1.3.6.1.4.1.97.3.18.3.1.7 | ColumnsipxSapHopCount | read-only | mandatory | A count of the number of routers that must be traversed to reach this server. |
| 1.3.6.1.4.1.97.3.18.4 | ScalarsipxDiscardedRoutes | read-only | mandatory | A count of the number of received routes that were lost due to insufficient resources. |
| 1.3.6.1.4.1.97.3.18.5 | ScalarsipxDiscardedServices | read-only | mandatory | A count of the number of received SAP services that were lost due to insufficient resources. |
| 1.3.6.1.4.1.97.3.18.6 | NodesipxsfGrp | |||
| 1.3.6.1.4.1.97.3.18.6.1 | ScalarsipxsfNextIndex | read-only | mandatory | Next available filter index for adding filters. Starting with 1, in sequetianl ascending order. |
| 1.3.6.1.4.1.97.3.18.6.2 | TablesipxsfTable | not-accessible | mandatory | This table defines the filtering criteria to be applied to Netware service advertisements. There can be no more than one filter per service name. Each filter i… |
| 1.3.6.1.4.1.97.3.18.6.2.1 | RowsipxsfEntry | not-accessible | mandatory | Defines the filtering criteria to be applied to a particular service name. |
| 1.3.6.1.4.1.97.3.18.6.2.1.1 | ColumnsipxsfIndex | read-write | mandatory | Assigned by the configurer to identify this filter. This index has no relationship to sipxSapIndex. |
| 1.3.6.1.4.1.97.3.18.6.2.1.2 | ColumnsipxsfSAPName | read-write | mandatory | The service name. `*' can be used as wild card character which match all names. |
| 1.3.6.1.4.1.97.3.18.6.2.1.3 | ColumnsipxsfSAPType | read-write | mandatory | The service type. Minus one or 65535 indicates all services of this name. Otherwise, the values are defined by Novell and other service providers (e.g., file s… |
| 1.3.6.1.4.1.97.3.18.6.2.1.4 | ColumnsipxsfAccessMode | read-write | mandatory | Permitted(1) allows the service name to be accepted or broadcasted. Denied(2) ignores the service name. Invalid(3) invalidates the filter entry. |
| 1.3.6.1.4.1.97.3.18.6.2.1.5 | ColumnsipxsfFilterType | read-write | mandatory | If entry(1), filter is for the incoming named service. If exit(2), filter is for the outgoing named service. |
| 1.3.6.1.4.1.97.3.18.6.2.1.6 | ColumnsipxsfPortMap | read-write | mandatory | A bit map defining port numbers to which the filter is applied. Octet 1 specifies port 1 to 8, octet 2 specifies port 9 to 16, and so on. Within each octet, th… |
| 1.3.6.1.4.1.97.3.18.6.2.1.7 | ColumnsipxsfNetworks | read-write | mandatory | A list of network addresses to which the filter is applied. Each network address consists of 4 octets (i.e. a LONG word). For filter with FilterType entry(1), … |
| 1.3.6.1.4.1.97.3.18.6.2.1.8 | ColumnsipxsfFiltered | read-only | mandatory | Number of times the service has been filtered. |
| 1.3.6.1.4.1.97.3.18.7 | NodesipxsrGrp | |||
| 1.3.6.1.4.1.97.3.18.7.1 | ScalarsipxsrAgingTime | read-write | mandatory | IPX source route cache age time, in seconds. |
| 1.3.6.1.4.1.97.3.18.7.2 | TablesipxsrExplorerTable | not-accessible | mandatory | IPX SR explorer configuration Table. |
| 1.3.6.1.4.1.97.3.18.7.2.1 | RowsipxsrExplorerEntry | not-accessible | mandatory | IPX SR explorer configuration for each port. |
| 1.3.6.1.4.1.97.3.18.7.2.1.1 | ColumnsipxsrPort | read-write | mandatory | Port number. |
| 1.3.6.1.4.1.97.3.18.7.2.1.2 | ColumnsipxsrStatus | read-write | mandatory | valid(1) to configure explorer type; invalid(2) to remove explorer configuration and default to STE. |
| 1.3.6.1.4.1.97.3.18.7.2.1.3 | ColumnsipxsrExplorerType | read-write | mandatory | use ARE or STE for explorer frame. |
| 1.3.6.1.4.1.97.3.19 | Nodesrtrdisc | |||
| 1.3.6.1.4.1.97.3.19.1 | TablesrtrdiscTable | not-accessible | mandatory | This table contains configuration information controlling operation of the router discovery protocol (RFC-1256). |
| 1.3.6.1.4.1.97.3.19.1.1 | RowsrtrdiscEntry | not-accessible | mandatory | Each entry in this table configures the router discovery protocol for the particular interface. |
| 1.3.6.1.4.1.97.3.19.1.1.1 | ColumnsrtrdiscIfIndex | read-only | mandatory | Identifies the interface (port) to which this entry's information belongs. The value of this variable corresponds to ifIndex, as well as most of the other port… |
| 1.3.6.1.4.1.97.3.19.1.1.2 | ColumnsrtrdiscState | read-write | mandatory | Specifies whether or not the router discovery protocol is in use for this interface. Defaults to disabled(2). |
| 1.3.6.1.4.1.97.3.19.1.1.3 | ColumnsrtrdiscAdvertisementAddress | read-write | mandatory | The IP address to be used for multicast router advertisements for this interface. If multicast(1), the all-systems multicast 224.0.0.1 is used. If broadcast, t… |
| 1.3.6.1.4.1.97.3.19.1.1.4 | ColumnsrtrdiscAdvertisementInterval | read-write | mandatory | The interval at which multicast router advertisements are to be transmitted, in seconds. Allowable values range between 4 and 1800. |
| 1.3.6.1.4.1.97.3.19.1.1.5 | ColumnsrtrdiscLifetime | read-write | mandatory | The value to be used for the Lifetime field of router advertisements. Values range from srtrdiscAdvertisementInterval to 9000. |
| 1.3.6.1.4.1.97.3.19.1.1.6 | ColumnsrtrdiscPreference | read-write | mandatory | The preferability of this interface's address as a default router, relative to other routers on the same subnet. |
| 1.3.6.1.4.1.97.3.20 | Nodesipm | |||
| 1.3.6.1.4.1.97.3.20.1 | Nodesipmroute | |||
| 1.3.6.1.4.1.97.3.20.1.1 | TablesipmRouteTable | not-accessible | mandatory | The (conceptual) table listing the origin routes that this router learns from neighboring routers and from initial installations of directly-connected routes. … |
| 1.3.6.1.4.1.97.3.20.1.1.1 | RowsipmRouteEntry | not-accessible | mandatory | An entry (conceptual row) representing information on an origin route when IPM is enabled. |
| 1.3.6.1.4.1.97.3.20.1.1.1.1 | ColumnsipmRouteOrigin | read-only | mandatory | The subnetwork address of the origin. |
| 1.3.6.1.4.1.97.3.20.1.1.1.2 | ColumnsipmRouteOriginMask | read-only | mandatory | The subnetwork mask of the origin. |
| 1.3.6.1.4.1.97.3.20.1.1.1.3 | ColumnsipmRouteGateway | read-only | mandatory | The next hop gateway toward the origin. This object has the value 0.0.0.0 for directly-connected routes. |
| 1.3.6.1.4.1.97.3.20.1.1.1.4 | ColumnsipmRouteMetric | read-only | mandatory | The distance to this origin in number of hops. |
| 1.3.6.1.4.1.97.3.20.1.1.1.5 | ColumnsipmRouteAge | read-write | mandatory | The time left for this origin route before aged out. |
| 1.3.6.1.4.1.97.3.20.1.1.1.6 | ColumnsipmRouteParents | read-only | mandatory | The bitmapped incoming port(s) for which this origin is learned. This is an octet string of length 8. The least significant bit of the eighth octet is port 0. … |
| 1.3.6.1.4.1.97.3.20.2 | Nodesipmgroup | |||
| 1.3.6.1.4.1.97.3.20.3 | Nodesipmneighbor | |||
| 1.3.6.1.4.1.97.3.20.3.1 | TablesipmNeighborTable | not-accessible | mandatory | The (conceptual) table listing the neighboring routers on each interface port. |
| 1.3.6.1.4.1.97.3.20.3.1.1 | RowsipmNeighborEntry | not-accessible | mandatory | An entry (conceptual row) all neighbors which are learned from this local interface port. |
| 1.3.6.1.4.1.97.3.20.3.1.1.1 | ColumnsipmNeighborIfIndex | read-only | mandatory | The ifIndex value of the interface for which this entry contains information. |
| 1.3.6.1.4.1.97.3.20.3.1.1.2 | ColumnsipmNeighbors | read-only | mandatory | The neighbor's IP address which was learned. |
| 1.3.6.1.4.1.97.3.20.3.1.1.3 | ColumnsipmNeighborLastHeard | read-only | mandatory | The elapsed time since the neighbor was last heard. |
| 1.3.6.1.4.1.97.3.20.4 | Nodesipmstat | |||
| 1.3.6.1.4.1.97.3.20.4.1 | ScalarsipmOutOfMemory | read-write | mandatory | The number of times IP Multicast routines try to allocate memory for routes which failed. |
| 1.3.6.1.4.1.97.3.20.4.2 | TablesipmStatTable | not-accessible | mandatory | The (conceptual) table containing multicast routing statistics for IP datagrams on a per port basis. |
| 1.3.6.1.4.1.97.3.20.4.2.1 | RowsipmStatEntry | not-accessible | mandatory | An entry (conceptual row) containing the multicast routing statistic for IP datagrams on a particular port. |
| 1.3.6.1.4.1.97.3.20.4.2.1.1 | ColumnsipmStatIfIndex | read-only | mandatory | The interface port number on which corresponding IPM statistics gather. |
| 1.3.6.1.4.1.97.3.20.4.2.1.2 | ColumnsipmInBadPackets | read-write | mandatory | The number of bad packets received which may include unknown DVMRP/IGMP messages, short packets, and checksum errors. |
| 1.3.6.1.4.1.97.3.20.4.2.1.3 | ColumnsipmCacheMiss | read-write | mandatory | The number of times IP Multicast packets need to lookup a route at the IP layer for determining forwarding path. |
| 1.3.6.1.4.1.97.3.21 | Nodesipckt | |||
| 1.3.6.1.4.1.97.3.21.1 | TablesipcktTable | not-accessible | mandatory | Defines attributes of IP circuits. A circuit is defined as a binding of a network number to a physical interface. |
| 1.3.6.1.4.1.97.3.21.1.1 | RowsipcktEntry | not-accessible | mandatory | Defines the attributes of a binding of IP address and network to physical interface. |
| 1.3.6.1.4.1.97.3.21.1.1.1 | ColumnsipcktIndex | read-write | mandatory | Identifies the physical interface. Identical to ifIndex. |
| 1.3.6.1.4.1.97.3.21.1.1.2 | ColumnsipcktIpAddress | read-write | mandatory | Identifies the IP network that is bound to this interface. |
| 1.3.6.1.4.1.97.3.21.1.1.3 | ColumnsipcktState | read-write | mandatory | The status of this binding. |
| 1.3.6.1.4.1.97.3.21.1.1.4 | ColumnsipcktNetMask | read-write | mandatory | The subnet mask for the network associated with this address binding. If set to 0.0.0.0, will default to standard class A/B/C mask, depending on the value of s… |
| 1.3.6.1.4.1.97.3.21.1.1.5 | ColumnsipcktSourceRoute | read-write | mandatory | Specifies the behavior of IP routing with respect to (link-layer) source routing for this circuit. If default(1) then behavior depends on whether the port is t… |
| 1.3.6.1.4.1.97.3.22 | TablesipNetToMediaTable | not-accessible | mandatory | An extension to the standard ipNetToMedia table, containing other ARP cache attributes, specifically the current source route to the destination. |
| 1.3.6.1.4.1.97.3.22.1 | RowsipNetToMediaEntry | not-accessible | mandatory | Each entry contains one IpAddress to `physical' address equivalence. Entries in this table exist even when there is no source route attached. |
| 1.3.6.1.4.1.97.3.22.1.1 | ColumnsipNetToMediaIfIndex | read-only | mandatory | The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified … |
| 1.3.6.1.4.1.97.3.22.1.2 | ColumnsipNetToMediaNetAddress | read-only | mandatory | The IpAddress corresponding to the media- dependent `physical' address. |
| 1.3.6.1.4.1.97.3.22.1.3 | ColumnsipNetToMediaSourceRoute | read-only | mandatory | The source route to this destination. |
| 1.3.6.1.4.1.97.3.22.1.4 | ColumnsipNetToMediaAge | read-only | mandatory | The age, in seconds, of the entry to this destination. |
| 1.3.6.1.4.1.97.3.23 | Nodessecure | |||
| 1.3.6.1.4.1.97.3.23.1 | TableprofileTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.97.3.23.1.1 | RowprofileEntry | not-accessible | mandatory | There may be up to 16,368 entries. A profile consists of up to 16 entries, all with the same value for profileIndex. and there may be no more than 1,023 profil… |
| 1.3.6.1.4.1.97.3.23.1.1.1 | ColumnprofileIndex | read-only | mandatory | A value from 1 to 1,023. All entries with the same profileIndex are part of the same profile. |
| 1.3.6.1.4.1.97.3.23.1.1.2 | ColumnprofileSourceStart | read-only | mandatory | Acceptable lowest value for the source port of a UDP or TCP packet. |
| 1.3.6.1.4.1.97.3.23.1.1.3 | ColumnprofileSourceEnd | read-only | mandatory | Acceptable highest value for the source port of a UDP or TCP packet. |
| 1.3.6.1.4.1.97.3.23.1.1.4 | ColumnprofileDestStart | read-only | mandatory | Acceptable lowest value for the destination port of a UDP or TCP packet. |
| 1.3.6.1.4.1.97.3.23.1.1.5 | ColumnprofileDestEnd | read-only | mandatory | Acceptable highest value for the destination port of a UDP or TCP packet. |
| 1.3.6.1.4.1.97.3.23.1.1.6 | ColumnprofileType | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.23.2 | TableruleTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.97.3.23.2.1 | RowruleEntry | not-accessible | mandatory | There may be up to 8,000 entries. Rules with 255.255.255.255 for both masks are accessed quickly; other rules are accessed less quickly. When adding a rule, at… |
| 1.3.6.1.4.1.97.3.23.2.1.1 | ColumnruleIndex | read-only | mandatory | An ES/1 port number. |
| 1.3.6.1.4.1.97.3.23.2.1.2 | ColumnruleSourceIp | read-only | mandatory | Source IP address. |
| 1.3.6.1.4.1.97.3.23.2.1.3 | ColumnruleDestIp | read-only | mandatory | Destination IP address. |
| 1.3.6.1.4.1.97.3.23.2.1.4 | ColumnruleSourceIpMask | read-only | mandatory | Mask to apply to the packet before comparing to ruleSourceIp. |
| 1.3.6.1.4.1.97.3.23.2.1.5 | ColumnruleDestIpMask | read-only | mandatory | Mask to apply to the packet before comparing to ruleSourceIp. |
| 1.3.6.1.4.1.97.3.23.2.1.6 | ColumnruleType | read-write | mandatory | |
| 1.3.6.1.4.1.97.3.23.2.1.7 | ColumnruleUdpProfile | read-write | mandatory | Which profile to use (i.e., the value of profileIndex) for UDP packets. A value of 0 means no profile, i.e., filter all packets. This rule only applies to pack… |
| 1.3.6.1.4.1.97.3.23.2.1.8 | ColumnruleTcpProfile | read-write | mandatory | Which profile to use (i.e., the value of profileIndex) for TCP packets for non-established sessions. A non-established session is indicated by neither the ACK … |
| 1.3.6.1.4.1.97.3.23.2.1.9 | ColumnruleTcpEstProfile | read-write | mandatory | Which profile to use (i.e., the value of profileIndex) for TCP packets for established sessions. An established session is indicated by the ACK or RST bit bein… |
| 1.3.6.1.4.1.97.3.23.2.1.10 | ColumnruleFilterUdpFragment | read-write | mandatory | Whether to filter UDP packets with a non-zero IP fragment offset. |
| 1.3.6.1.4.1.97.3.23.2.1.11 | ColumnruleFilterTcpFragment | read-write | mandatory | Whether to filter TCP packets with a non-zero IP fragment offset. |
| 1.3.6.1.4.1.97.3.23.2.1.12 | ColumnruleFilterIpOption | read-write | mandatory | Whether to filter packets with an IP header length of other than 5. |
| 1.3.6.1.4.1.97.3.23.2.1.13 | ColumnruleAllowIcmp | read-write | mandatory | Whether to forward ICMP packets (IP protocol 1). |
| 1.3.6.1.4.1.97.3.23.2.1.14 | ColumnruleAllowIpWithinIp | read-write | mandatory | Whether to forward IP encapsulated within IP packets (IP protocol 4). |
| 1.3.6.1.4.1.97.3.23.2.1.15 | ColumnruleAllowEgp | read-write | mandatory | Whether to forward EGP packets (IP protocol 8). |
| 1.3.6.1.4.1.97.3.23.2.1.16 | ColumnruleAllowIgp | read-write | mandatory | Whether to forward IGP packets (IP protocol 9). |
| 1.3.6.1.4.1.97.3.23.2.1.17 | ColumnruleAllowIgrp | read-write | mandatory | Whether to forward IGP packets (IP protocol 88). |
| 1.3.6.1.4.1.97.3.23.2.1.18 | ColumnruleAllowOspf | read-write | mandatory | Whether to forward OSPF packets (IP protocol 89). |
| 1.3.6.1.4.1.97.3.23.2.1.19 | ColumnruleAllowAnyOther | read-write | mandatory | Whether to forward all other types of IP packets (i.e., other than UDP, TCP, ICMP, IP encapsulated, EGP, IGP, IGRP, and OSPF). |
| 1.3.6.1.4.1.97.3.24 | Nodespvc | |||
| 1.3.6.1.4.1.97.3.24.1 | TablespvcTable | not-accessible | mandatory | This table maps pseudo-port indices to permanent virtual circuits. |
| 1.3.6.1.4.1.97.3.24.1.1 | RowspvcEntry | not-accessible | mandatory | Each entry in this table describes one permanent virtual circuit. |
| 1.3.6.1.4.1.97.3.24.1.1.1 | ColumnspvcIfIndex | read-only | mandatory | Identifies the virtual interface (port) on which this virtual circuit exists. The value of this variable corresponds to ifIndex, as well as most of the other p… |
| 1.3.6.1.4.1.97.3.24.1.1.2 | ColumnspvcPathRX | read-write | mandatory | Where virtual circuit identifiers are split into two parts, as in ATM, this is the most-significant part, and is identical to the ATM virtual path identifier. |
| 1.3.6.1.4.1.97.3.24.1.1.3 | ColumnspvcCircuitRX | read-write | mandatory | Where virtual circuit identifiers are split into two parts, as in ATM, this is the least-significant part, and is identical to the ATM virtual circuit identifi… |
| 1.3.6.1.4.1.97.3.24.1.1.4 | ColumnspvcPathTX | read-write | mandatory | Where virtual circuit identifiers are split into two parts, as in ATM, this is the most-significant part, and is identical to the ATM virtual path identifier. |
| 1.3.6.1.4.1.97.3.24.1.1.5 | ColumnspvcCircuitTX | read-write | mandatory | Where virtual circuit identifiers are split into two parts, as in ATM, this is the least-significant part, and is identical to the ATM virtual circuit identifi… |
| 1.3.6.1.4.1.97.3.24.1.1.6 | ColumnspvcState | read-write | mandatory | Controls the existence of this table entry. |
| 1.3.6.1.4.1.97.3.24.1.1.7 | ColumnspvcPhysPort | read-only | mandatory | Identifies the physical interface (port) on which this virtual circuit exists. The value of this variable corresponds to ifIndex, as well as most of the other … |
| 1.3.6.1.4.1.97.3.24.2 | ScalarspvcMinPort | read-only | mandatory | The lowest-numbered PVC pseudo-port number. |
| 1.3.6.1.4.1.97.3.24.3 | ScalarspvcMaxPort | read-only | mandatory | The highest-numbered PVC pseudo-port number. |
| 1.3.6.1.4.1.97.3.25 | Nodestrunk | |||
| 1.3.6.1.4.1.97.3.25.1 | TablestrunkTable | not-accessible | mandatory | This table describes the trunking status and attributes of the interfaces that are configured for bridge trunking. |
| 1.3.6.1.4.1.97.3.25.1.1 | RowstrunkEntry | not-accessible | mandatory | An entry exists in this table for each physical interface (port) that is configured for trunking. |
| 1.3.6.1.4.1.97.3.25.1.1.1 | ColumnstrunkIfIndex | read-only | mandatory | Identifies a physical interface (port) which is configured for LAN trunking. The value of this variable corresponds to ifIndex, as well as most of the other po… |
| 1.3.6.1.4.1.97.3.25.1.1.2 | ColumnstrunkState | read-only | mandatory | If off(1) then this link has not been enabled for trunking. If closed(2) then this link has not yet received any Trunking PDUs. If oneway(3) then incoming Trun… |
| 1.3.6.1.4.1.97.3.25.1.1.3 | ColumnstrunkRemoteBridgeAddr | read-only | mandatory | The MAC address portion of the bridge ID of the remote bridge. |
| 1.3.6.1.4.1.97.3.25.1.1.4 | ColumnstrunkRemoteIp | read-only | mandatory | The IP address of the remote bridge, as reported by that bridge for administrative purposes. |
| 1.3.6.1.4.1.97.3.25.1.1.5 | ColumnstrunkLastError | read-only | mandatory | The last reason for failure when the link is in closed, oneway, or helddown state. |
| 1.3.6.1.4.1.97.3.25.1.1.6 | ColumnstrunkLinkOrdinal | read-only | mandatory | The position of this link within the trunk group. |
| 1.3.6.1.4.1.97.3.25.1.1.7 | ColumnstrunkLinkCount | read-only | mandatory | The number of links within the trunk group. |
| 1.3.6.1.4.1.97.3.25.1.1.8 | ColumnstrunkLastChange | read-only | mandatory | The number of seconds since strunkState changed. |
| 1.3.6.1.4.1.97.3.26 | NodeipMRouteMIB | |||
| 1.3.6.1.4.1.97.3.26.1 | NodeipMRouteMIBObjects | |||
| 1.3.6.1.4.1.97.3.26.1.1 | NodeipMRoute | |||
| 1.3.6.1.4.1.97.3.26.1.1.1 | ScalaripMRouteEnable | read-write | mandatory | The enabled status of IP Multicast routing on this router. |
| 1.3.6.1.4.1.97.3.26.1.1.2 | TableipMRouteTable | not-accessible | mandatory | The (conceptual) table containg multicast routing information for IP datagrams sent by particular sources to the IP multicast groups known to this router. |
| 1.3.6.1.4.1.97.3.26.1.1.2.1 | RowipMRouteEntry | not-accessible | mandatory | An entry (conceptual row) containing the multicast routing information for IP datagrams from a particular source and addressed to a particular IP multicast gro… |
| 1.3.6.1.4.1.97.3.26.1.1.2.1.1 | ColumnipMRouteGroup | read-only | mandatory | The IP multicast group address for which this entry contains multicast routing information. |
| 1.3.6.1.4.1.97.3.26.1.1.2.1.2 | ColumnipMRouteSource | read-only | mandatory | The source network address for which this entry contains multicast routing information. |
| 1.3.6.1.4.1.97.3.26.1.1.2.1.3 | ColumnipMRouteSourceMask | read-only | mandatory | The network mask of the source address for which this entry contains multicast routing information. |
| 1.3.6.1.4.1.97.3.26.1.1.2.1.4 | ColumnipMRouteRpfNeighbor | read-only | mandatory | The address of the RPF neighbor from which IP datagrams from this source to this multicast address are received. |
| 1.3.6.1.4.1.97.3.26.1.1.2.1.5 | ColumnipMRouteInIfIndex | read-only | mandatory | The value of ifIndex for the interface on which IP datagrams sent by this source to this multicast address are received. |
| 1.3.6.1.4.1.97.3.26.1.1.2.1.6 | ColumnipMRouteOutList | read-only | mandatory | The value of ipMRouteNextHopList which identifies the list of entries in the ipMRouteNextHopTable representing outgoing interfaces to which IP datagrams from t… |
| 1.3.6.1.4.1.97.3.26.1.1.2.1.7 | ColumnipMRouteUpTime | read-only | mandatory | The time since the multicast routing information represented by this entry was learned by the router. |
| 1.3.6.1.4.1.97.3.26.1.1.2.1.8 | ColumnipMRouteExpiryTime | read-write | mandatory | The minimum amount of time remaining before this entry will be aged out. |
| 1.3.6.1.4.1.97.3.26.1.1.2.1.9 | ColumnipMRoutePkts | read-only | mandatory | The number of packets which this router has received from this source and addressed to this multicast group address. |
| 1.3.6.1.4.1.97.3.26.1.1.2.1.10 | ColumnipMRouteRpfFails | read-only | mandatory | The number of packets which this router has received from this source and addressed to this multicast group address, which were not received from the interface… |
| 1.3.6.1.4.1.97.3.26.1.1.2.1.11 | ColumnipMRouteOctets | read-only | mandatory | The number of octets contained in IP datagrams which were received from this source and addressed to this multicast group address, and which were forwarded by … |
| 1.3.6.1.4.1.97.3.26.1.1.2.1.12 | ColumnipMRouteNextHopState | read-only | mandatory | An indication of whether the outgoing interface and next hop represented by this entry is currently being used to forward IP datagrams. The value 'forwarding' … |
| 1.3.6.1.4.1.97.3.26.1.1.3 | TableipMRouteInterfaceTable | not-accessible | mandatory | The (conceptual) table containg multicast routing information specific to interfaces. |
| 1.3.6.1.4.1.97.3.26.1.1.3.1 | RowipMRouteInterfaceEntry | not-accessible | mandatory | An entry (conceptual row) containing the multicast routing information for a particular interface. |
| 1.3.6.1.4.1.97.3.26.1.1.3.1.1 | ColumnipMRouteInterfaceIfIndex | read-only | mandatory | The ifIndex value of the interface for which this entry contains information. |
| 1.3.6.1.4.1.97.3.26.1.1.3.1.2 | ColumnipMRouteInterfaceTtl | read-write | mandatory | The datagram TTL threshold for the interface. Any IP multicast datagrams with a TTL less than this threshold will not be forwarded out the interface. The defau… |
| 1.3.6.1.4.1.97.3.27 | NodeigmpMIB | |||
| 1.3.6.1.4.1.97.3.27.1 | NodeigmpMIBObjects | |||
| 1.3.6.1.4.1.97.3.27.1.1 | Nodeigmp | |||
| 1.3.6.1.4.1.97.3.27.1.1.1 | TableigmpInterfaceTable | not-accessible | mandatory | The (conceptual) table listing the interfaces on which IGMP is enabled. |
| 1.3.6.1.4.1.97.3.27.1.1.1.1 | RowigmpInterfaceEntry | not-accessible | mandatory | An entry (conceptual row) representing an interface on which IGMP is enabled. |
| 1.3.6.1.4.1.97.3.27.1.1.1.1.1 | ColumnigmpInterfaceIfIndex | read-only | mandatory | The interface for which IGMP is enabled. |
| 1.3.6.1.4.1.97.3.27.1.1.1.1.2 | ColumnigmpInterfaceQueryInterval | read-write | mandatory | The frequency at which IGMP Host-Query packets are transmitted on this interface. |
| 1.3.6.1.4.1.97.3.27.1.1.1.1.3 | ColumnigmpInterfaceStatus | read-write | mandatory | The activation of a row enables IGMP on the interface. The destruction of a row disables IGMP on the interface. |
| 1.3.6.1.4.1.97.3.27.1.1.2 | TableigmpCacheTable | not-accessible | mandatory | The (conceptual) table listing the IP multicast groups for which there are members on a particular interface. |
| 1.3.6.1.4.1.97.3.27.1.1.2.1 | RowigmpCacheEntry | not-accessible | mandatory | An entry (conceptual row) in the igmpCacheTable. |
| 1.3.6.1.4.1.97.3.27.1.1.2.1.1 | ColumnigmpCacheAddress | read-only | mandatory | The IP multicast group address for which this entry contains information. |
| 1.3.6.1.4.1.97.3.27.1.1.2.1.2 | ColumnigmpCacheIfIndex | read-only | mandatory | The interface for which this entry contains information for an IP multicast group address. |
| 1.3.6.1.4.1.97.3.27.1.1.2.1.3 | ColumnigmpCacheSelf | read-write | mandatory | An indication of whether the local system is a member of this group address on this interface. |
| 1.3.6.1.4.1.97.3.27.1.1.2.1.4 | ColumnigmpCacheLastReporter | read-only | mandatory | The IP address of the source of the last membership report received for this IP Multicast group address on this interface. If no membership report has been rec… |
| 1.3.6.1.4.1.97.3.27.1.1.2.1.5 | ColumnigmpCacheUpTime | read-only | mandatory | The time since the system joined this group address, or zero if the system is not currently a member. |
| 1.3.6.1.4.1.97.3.27.1.1.2.1.6 | ColumnigmpCacheExpiryTime | read-only | mandatory | The minimum amount of time remaining before this entry will be aged out. |
| 1.3.6.1.4.1.97.3.27.1.1.2.1.7 | ColumnigmpCacheStatus | read-write | mandatory | The status of this entry. |
| 1.3.6.1.4.1.97.3.28 | Nodeslog | |||
| 1.3.6.1.4.1.97.3.28.1 | ScalarslogFilter | read-write | mandatory | The current event logging filter, represented as a bitmask. |
| 1.3.6.1.4.1.97.3.28.2 | ScalarslogTrap | read-write | mandatory | When enabled, logging entries will cause SNMP traps to be generated. |
| 1.3.6.1.4.1.97.3.28.3 | ScalarslogOverwrite | read-write | mandatory | When enabled, logging entries will be overwritten in the logging queue. When disabled, the entries in the logging queue will not be overwritten until someone r… |
| 1.3.6.1.4.1.97.3.28.4 | ScalarslogEntryNumber | read-only | mandatory | The number of entries in the logging entry table. |
| 1.3.6.1.4.1.97.3.28.5 | TableslogEntryTable | not-accessible | mandatory | This table contains the event logging entries. |
| 1.3.6.1.4.1.97.3.28.5.1 | RowslogEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.97.3.28.5.1.1 | ColumnslogIndex | read-only | mandatory | The index of the logging entry in the logging entry table. |
| 1.3.6.1.4.1.97.3.28.5.1.2 | ColumnslogEntryTimeStamp | read-only | mandatory | The time at which the event logging entry was generated. |
| 1.3.6.1.4.1.97.3.28.5.1.3 | ColumnslogEntryMessageText | read-only | mandatory | The text of the eventlogging entry message. |
| 1.3.6.1.4.1.97.3.28.5.1.4 | ColumnslogEntryName | read-only | mandatory | The name of the event logging entry. |
| 1.3.6.1.4.1.97.3.29 | Nodestrap | |||
| 1.3.6.1.4.1.97.3.29.1 | TablestrapControlTable | not-accessible | mandatory | This table contains information about the severity of each trap and whether the trap is currently enabled. |
| 1.3.6.1.4.1.97.3.29.1.1 | RowstrapControl | not-accessible | mandatory | |
| 1.3.6.1.4.1.97.3.29.1.1.1 | ColumnstrapIndex | read-only | mandatory | The specific trap number. |
| 1.3.6.1.4.1.97.3.29.1.1.2 | ColumnstrapEnabled | read-write | mandatory | Enable or disable the generation of this trap. |
| 1.3.6.1.4.1.97.3.29.1.1.3 | ColumnstrapSeverity | read-write | mandatory | A user-definable severity, indicating the importance of the trap. |
| 1.3.6.1.4.1.97.3.29.1.1.4 | ColumnstrapText | read-only | mandatory | A description of the trap. |
| 1.3.6.1.4.1.97.3.29.2 | TablestrapSeverityControlTable | not-accessible | mandatory | This table contains information about the whether a class of traps of a particular severity are enabled or disabled. |
| 1.3.6.1.4.1.97.3.29.2.1 | RowstrapSeverityControl | not-accessible | mandatory | |
| 1.3.6.1.4.1.97.3.29.2.1.1 | ColumnstrapSeveritySeverity | read-only | mandatory | A user-definable severity, indicating the importance of the trap. |
| 1.3.6.1.4.1.97.3.29.2.1.2 | ColumnstrapSeverityEnable | read-write | mandatory | Enable or disable all traps of a given severity level. |
| 1.3.6.1.4.1.97.3.29.3 | ScalarstrapIncludeText | read-write | mandatory | Whether or not a formatted text string is included in the trap PDU. |
| 1.3.6.1.4.1.97.3.29.4 | ScalarstrapTime | read-write | mandatory | (This MIB variable replaces sysTrapTime). The time, in centiseconds, which should expire between the sending of traps. |
| 1.3.6.1.4.1.97.3.29.5 | ScalarstrapRetry | read-write | mandatory | The number of times any enterprise-specific trap is to be sent for a given event. PDUs are retried using a truncated exponential backoff: 2 seconds, 4 seconds,… |
| 1.3.6.1.4.1.97.3.29.6 | ScalarstrapEntryNumber | read-only | mandatory | The number of traps that are in the strapTable. |
| 1.3.6.1.4.1.97.3.29.7 | TablestrapTable | not-accessible | mandatory | This table contains the latest traps that have been generated. |
| 1.3.6.1.4.1.97.3.29.7.1 | RowstrapEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.97.3.29.7.1.1 | ColumnstrapEntryIndex | read-only | mandatory | A number representing the order in which the trap occurred in time. This 32 bit number can wrap. |
| 1.3.6.1.4.1.97.3.29.7.1.2 | ColumnstrapEntryTimeStamp | read-only | mandatory | The time at which the trap occurred. |
| 1.3.6.1.4.1.97.3.29.7.1.3 | ColumnstrapEntryText | read-only | mandatory | A description of the trap. |
| 1.3.6.1.4.1.97.3.29.7.1.4 | ColumnstrapNumber | read-only | mandatory | The specific-trap number, as specified in the TRAP PDU. |
| 1.3.6.1.4.1.97.3.29.7.1.5 | ColumnstrapEntrySeverity | read-only | mandatory | A user-definable severity, indicating the importance of the trap. |
| 1.3.6.1.4.1.97.3.30 | Nodesmirror | |||
| 1.3.6.1.4.1.97.3.30.1 | ScalarsmirrorStatus | read-write | mandatory | invalid(1) to turn off port mirroring. local(2) to mirror either to a local port or to a remote ATX. remote(3) to mirror traffics from a remote ATX to a local … |
| 1.3.6.1.4.1.97.3.30.2 | ScalarsmirrorDiagPort | read-write | mandatory | This entry defines the diagnostic port to output mirrored packets. It can be one of the Ethernet, Token Ring or FDDI interfaces in the ATX. |
| 1.3.6.1.4.1.97.3.30.3 | ScalarsmirrorIPaddr | read-write | mandatory | This entry defines the IP address for remote mirroring. It must be a valid host address. |
| 1.3.6.1.4.1.97.3.30.4 | ScalarsmirrorTargetPortLists | read-write | mandatory | An octet string specifies the list of ports to be mirrored, with each octet representing a single port number. |
| 1.3.6.1.4.1.97.3.30.5 | ScalarsmirrorOversizePkt | read-write | mandatory | Specified whether to discard or truncate oversized mirrored packets. |
| 1.3.6.1.4.1.97.3.30.6 | ScalarsmirrorEntryMirroredPkts | read-only | mandatory | Number of entry packets mirrored. |
| 1.3.6.1.4.1.97.3.30.7 | ScalarsmirrorExitMirroredPkts | read-only | mandatory | Number of exit packets mirrored. |
| 1.3.6.1.4.1.97.3.30.8 | ScalarsmirrorNotreadyDroppedPkts | read-only | mandatory | Number of packets not mirrored either because the diagnostic port is not ready (local mirroring) or the tunnel to remote ATX is not ready (remote mirroring). |
| 1.3.6.1.4.1.97.3.30.9 | ScalarsmirrorOversizeDroppedPkts | read-only | mandatory | Number of oversized packets not mirrored. |
| 1.3.6.1.4.1.97.3.30.10 | ScalarsmirrorEntryFilteredPkts | read-only | mandatory | Number of entry packets filtered. |
| 1.3.6.1.4.1.97.3.30.11 | ScalarsmirrorExitFilteredPkts | read-only | mandatory | Number of exit packets filtered. |
| 1.3.6.1.4.1.97.3.30.12 | ScalarsmirrorCongestionDroppedPkts | read-only | mandatory | Number of packets not mirrored due to exit port congestion. |
| 1.3.6.1.4.1.97.3.30.13 | ScalarsmirrorNowrapperDroppedPkts | read-only | mandatory | Number of packets not mirrored due to shortage of wrapper buffers (in mirroring frames to remote ATX). |
| 1.3.6.1.4.1.97.3.30.14 | ScalarsmirrorRemoteStatus | read-only | mandatory | Status when mirroring to remote ATX. |
| 1.3.6.1.4.1.97.3.30.15 | ScalarsmirrorRemoteExitPort | read-only | mandatory | Mirrored packets exit port number to remote ATX. |
| 1.3.6.1.4.1.97.3.31 | Nodesworkgroup | |||
| 1.3.6.1.4.1.97.3.31.1 | ScalarsWorkGroupNextNumber | read-only | mandatory | The next available workgroup number to be used. When creating a new workgroup, it is recommended to read the value of the variable and use it to key into the w… |
| 1.3.6.1.4.1.97.3.31.2 | ScalarsWorkGroupCurrentCount | read-only | mandatory | The total number of workgroups currently defined. |
| 1.3.6.1.4.1.97.3.31.3 | ScalarsWorkGroupMaxCount | read-only | mandatory | The maximum number of workgroups allowed. |
| 1.3.6.1.4.1.97.3.31.4 | TablesWorkGroupTable | not-accessible | mandatory | This table contains work group definitions for the interfaces. |
| 1.3.6.1.4.1.97.3.31.4.1 | RowsWorkGroupEntry | not-accessible | mandatory | Each entry in this table contains a definition of a work group. |
| 1.3.6.1.4.1.97.3.31.4.1.1 | ColumnsWorkGroupNumber | read-write | mandatory | An integer that identifies the work group, used as an index to this table. |
| 1.3.6.1.4.1.97.3.31.4.1.2 | ColumnsWorkGroupName | read-write | mandatory | A 1-16 character work group name. |
| 1.3.6.1.4.1.97.3.31.4.1.3 | ColumnsWorkGroupPorts | read-write | mandatory | A list of all ports within the group. The first octet specified ports 1-8, the second 9-16, etc. |
| 1.3.6.1.4.1.97.3.31.4.1.4 | ColumnsWorkGroupType | read-write | mandatory | The type of work group: all - no additional information needs to be supplied. ip - the IP network (and optionally, IP mask) must be supplied. ipx - the IPX net… |
| 1.3.6.1.4.1.97.3.31.4.1.5 | ColumnsWorkGroupIpAddress | read-write | mandatory | The IP network address. |
| 1.3.6.1.4.1.97.3.31.4.1.6 | ColumnsWorkGroupIpMask | read-write | mandatory | The IP network mask, if set to 0, the default network mask is applied. |
| 1.3.6.1.4.1.97.3.31.4.1.7 | ColumnsWorkGroupIpxNetwork | read-write | mandatory | The IPX network number, 0 means all networks. |
| 1.3.6.1.4.1.97.3.32 | Nodesping | |||
| 1.3.6.1.4.1.97.3.32.1 | ScalarspingDataTimeout | read-write | mandatory | The time, in centiseconds, from the last ping activity (a send or receive of an ECHO_RESPONSE or ECHO_REQUEST message), to when the spingEntry information for … |
| 1.3.6.1.4.1.97.3.32.2 | TablespingTable | not-accessible | mandatory | The set of information describing the active ping requests and their results. |
| 1.3.6.1.4.1.97.3.32.2.1 | RowspingEntry | not-accessible | mandatory | The parameters, state and results of a ping request. |
| 1.3.6.1.4.1.97.3.32.2.1.1 | ColumnspingNMSAddr | read-only | mandatory | The IP address of the NMS, used to determine which ping request to return information on. |
| 1.3.6.1.4.1.97.3.32.2.1.2 | ColumnspingDestAddr | read-write | mandatory | The IP address which is to be the destination of the ping ECHO_REQUEST. This variable cannot be set while spingOperation is on. |
| 1.3.6.1.4.1.97.3.32.2.1.3 | ColumnspingState | read-only | mandatory | The current state of the ping request. |
| 1.3.6.1.4.1.97.3.32.2.1.4 | ColumnspingCount | read-write | mandatory | The number of ping requests which are to be sent. This variable cannot be set while spingOperation is on. |
| 1.3.6.1.4.1.97.3.32.2.1.5 | ColumnspingDataSize | read-write | mandatory | The datagram packet size which will be sent with the ECHO_REQUEST, in bytes. This variable cannot be set while spingOperation is on. |
| 1.3.6.1.4.1.97.3.32.2.1.6 | ColumnspingWait | read-write | mandatory | The time, in centiseconds, between the sending of each ECHO_REQUEST message. This variable cannot be set while spingOperation is on. |
| 1.3.6.1.4.1.97.3.32.2.1.7 | ColumnspingTimeout | read-write | mandatory | The time, in centiseconds, since the last ECHO_RESPONSE was received (or the last ECHO_REQUEST was sent, if there have been no responses) when the ping request… |
| 1.3.6.1.4.1.97.3.32.2.1.8 | ColumnspingOperation | read-write | mandatory | Setting spingOperation to on will begin the ping request. Setting spingOperation to off will terminate the ping request. |
| 1.3.6.1.4.1.97.3.32.2.1.9 | ColumnspingMin | read-only | mandatory | The minimum round trip time for the ping requests and responses, in centiseconds. |
| 1.3.6.1.4.1.97.3.32.2.1.10 | ColumnspingMax | read-only | mandatory | The maximum round trip for the ping requests and responses, in centiseconds. |
| 1.3.6.1.4.1.97.3.32.2.1.11 | ColumnspingAvg | read-only | mandatory | The average round trip time for the ping requests and responses, in centiseconds. |
| 1.3.6.1.4.1.97.3.32.2.1.12 | ColumnspingNumTransmitted | read-only | mandatory | The number of ICMP ECHO_REQUEST messages that have been transmitted during this ping request. |
| 1.3.6.1.4.1.97.3.32.2.1.13 | ColumnspingNumReceived | read-only | mandatory | The number of ICMP ECHO_RESPONSE messages that have been received as a result of this ping request. |
| 1.3.6.1.4.1.97.3.33 | Nodestrace | |||
| 1.3.6.1.4.1.97.3.33.1 | ScalarstraceDataTimeout | read-write | mandatory | The time, in centiseconds, from the last traceroute activity (the response to or timeout of the last probe sent), to when the straceEntry information for that … |
| 1.3.6.1.4.1.97.3.33.2 | TablestraceTable | not-accessible | mandatory | The set of information describing the active traceroute requests and their results. |
| 1.3.6.1.4.1.97.3.33.2.1 | RowstraceEntry | not-accessible | mandatory | The parameters, state, and results of a traceroute request. |
| 1.3.6.1.4.1.97.3.33.2.1.1 | ColumnstraceNMSAddr | read-only | mandatory | The IP address of the NMS, used to determine which traceroute request to return information on. |
| 1.3.6.1.4.1.97.3.33.2.1.2 | ColumnstraceDestAddr | read-write | mandatory | The IP address which is to be the destination of the traceroute request.This variable cannot be set while straceOperation is on. |
| 1.3.6.1.4.1.97.3.33.2.1.3 | ColumnstraceMaxTTL | read-write | mandatory | The maximum time-to-live for outgoing traceroute probe packets. This determines the number of hops that can be in a traceroute. This variable cannot be set whi… |
| 1.3.6.1.4.1.97.3.33.2.1.4 | ColumnstraceDataSize | read-write | mandatory | The size of the datagram sent with each probe. This variable cannot be set while straceOperation is on. |
| 1.3.6.1.4.1.97.3.33.2.1.5 | ColumnstraceNumProbes | read-write | mandatory | The number of probes which are sent for each hop. This variable cannot be set while straceOperation is on. |
| 1.3.6.1.4.1.97.3.33.2.1.6 | ColumnstraceWait | read-write | mandatory | The time to wait in response to a probe. This variable cannot be set while straceOperation is on. |
| 1.3.6.1.4.1.97.3.33.2.1.7 | ColumnstraceOperation | read-write | mandatory | Setting straceOperation to on will begin the traceroute request. Setting straceOperation to off will terminate the traceroute request. |
| 1.3.6.1.4.1.97.3.33.2.1.8 | ColumnstraceHop | read-only | mandatory | The hop count for a set of probes with a particular TTL. |
| 1.3.6.1.4.1.97.3.33.2.1.9 | ColumnstraceHopAddress | read-only | mandatory | The IP address of the host which responded for a probe with a particular TTL. |
| 1.3.6.1.4.1.97.3.33.2.1.10 | ColumnstraceProbe | read-only | mandatory | The probe instance for a particular hop. |
| 1.3.6.1.4.1.97.3.33.2.1.11 | ColumnstraceState | read-only | mandatory | The current state of the trace probe. |
| 1.3.6.1.4.1.97.3.33.2.1.12 | ColumnstraceTime | read-only | mandatory | Round trip time of a probe for a particular hop. |
| 1.3.6.1.4.1.97.3.34 | Nodesrtb | |||
| 1.3.6.1.4.1.97.3.34.1 | ScalarsrtbProto | read-write | mandatory | Bit mapped representation of srtb protocol configuration. |
| 1.3.6.1.4.1.97.3.34.2 | ScalarsrtbExplorer | read-write | mandatory | Type of explorer to transmit. |
| 1.3.6.1.4.1.97.3.34.3 | ScalarsrtbAgingTime | read-only | mandatory | RIF aging time value. |
| 1.3.6.1.4.1.97.3.35 | Nodenbcache | |||
| 1.3.6.1.4.1.97.3.35.3 | TablenbCacheifTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.97.3.35.3.1 | RownbCacheifEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.97.3.35.3.1.1 | ColumnnbCacheIfIndex | read-only | mandatory | This is the primary index into the Netbios Interface Table. It is the port number which you intend to enable/disable Netbios Caching. |
| 1.3.6.1.4.1.97.3.35.3.1.2 | ColumnnbCacheIfOperStatus | read-write | mandatory | Indicates the operating state of netbios name caching for this port. |
| 1.3.6.1.4.1.97.6 | Nodeatext | |||
| 1.3.6.1.4.1.97.6.1 | Nodeatextsystem | |||
| 1.3.6.1.4.1.97.6.1.1 | ScalaratextsysOperState | read-write | mandatory | The operational state of AppleTalk routing. |
| 1.3.6.1.4.1.97.6.2 | Nodeatextport | |||
| 1.3.6.1.4.1.97.6.2.1 | TableatextportTable | not-accessible | mandatory | A list of AppleTalk ports for this entity. |
| 1.3.6.1.4.1.97.6.2.1.1 | RowatextportEntry | not-accessible | mandatory | The description of one of the AppleTalk ports on this entity. |
| 1.3.6.1.4.1.97.6.2.1.1.1 | ColumnatextportIndex | read-only | mandatory | A unique value for each AppleTalk port. Its value is between 1 and the total number of AppleTalk ports. The value for each port must remain constant at least f… |
| 1.3.6.1.4.1.97.6.2.1.1.2 | ColumnatextportNetStart | read-only | mandatory | The first AppleTalk network address in the configured range for this port. This is a two octet DDP network address in network byte order. |
| 1.3.6.1.4.1.97.6.2.1.1.3 | ColumnatextportNetEnd | read-only | mandatory | The last AppleTalk network address in the configured range for this port. This is a two octet DDP network address in network byte order. |
| 1.3.6.1.4.1.97.6.2.1.1.4 | ColumnatextportNetAddress | read-only | mandatory | The AppleTalk network address configured for this port. |
| 1.3.6.1.4.1.97.6.2.1.1.5 | ColumnatextportZone | read-only | mandatory | The default zone name configured for this AppleTalk port. |
| 1.3.6.1.4.1.97.6.2.2 | TableatextportzipTable | not-accessible | mandatory | The table of zone information configured for a port. |
| 1.3.6.1.4.1.97.6.2.2.1 | RowatextportzipEntry | not-accessible | mandatory | An entry of zone information for a particular zone and port combination. |
| 1.3.6.1.4.1.97.6.2.2.1.1 | ColumnatextportZonePort | read-only | mandatory | A unique value for each AppleTalk port. |
| 1.3.6.1.4.1.97.6.2.2.1.2 | ColumnatextportZoneIndex | read-only | mandatory | An integer that is unique to the ZoneName that is present in this entry. For any given zone name, every Entry that has an equal zone name will have the same Zo… |
| 1.3.6.1.4.1.97.6.2.2.1.3 | ColumnatextportZoneName | read-only | mandatory | The ASCII zone name of this entry. |