CTRON-COMMON-MIB
111 objects
No module-level DESCRIPTION found.
Imported Objects
| IRM-OIDS | commonRev1 dl subSysDevice subSysMMAC ups |
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter NetworkAddress |
| RFC1213-MIB | DisplayString PhysAddress |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.52.1.1.1.1 | ScalardeviceType | read-only | mandatory | The type of management board. |
| 1.3.6.1.4.1.52.1.1.1.2 | ScalardeviceName | read-write | mandatory | A textual description on the entity managed by the resident agent. It is mandatory that this only con- tain printable ASCII characters. |
| 1.3.6.1.4.1.52.1.1.1.3 | ScalardeviceIPAddress | read-write | mandatory | The Network address, in this case the IP address, of the device. This object is required for use by the Local Management Interface. |
| 1.3.6.1.4.1.52.1.1.1.4 | ScalardeviceTime | read-write | mandatory | The current time of day, in 24 hour format, as measured by the device. The representation shall use the standard HHMMSS format. |
| 1.3.6.1.4.1.52.1.1.1.5 | ScalardeviceDate | read-write | mandatory | The current date, as measured by the device. The representation shall use the standard MMDDYYYY format. |
| 1.3.6.1.4.1.52.1.6.1.2 | Nodefnb2 | |||
| 1.3.6.1.4.1.52.1.6.1.2.1 | NodefnbTR | |||
| 1.3.6.1.4.1.52.1.6.1.2.1.1 | TablefnbTRTable | not-accessible | mandatory | A list of entries that provide connection status of Token Ring subsystems, for the FNB. |
| 1.3.6.1.4.1.52.1.6.1.2.1.1.1 | RowfnbTREntry | not-accessible | mandatory | An entry in the fnbTRTable containing objects that provide FNB connection status for a Token Ring sub- system. |
| 1.3.6.1.4.1.52.1.6.1.2.1.1.1.1 | ColumnfnbTRIndex | read-only | mandatory | An unique value for each Token Ring subsystem. Its value ranges between 1 and chassisSlots. The value for each interface must remain constant, at least, from o… |
| 1.3.6.1.4.1.52.1.6.1.2.1.1.1.2 | ColumnfnbConnectLeft | read-write | mandatory | The Connected Left board (board n + 1) has the following states: Detached == 1 (Management (only management) detached, read/write). Attached == 2 (Management/A… |
| 1.3.6.1.4.1.52.1.6.1.2.1.1.1.3 | ColumnfnbConnectRight | read-write | mandatory | The Connected Right board (board n - 1) has the following states: Detached == 1 (Management (only management) detached, read/write). Attached == 2 (Management/… |
| 1.3.6.1.4.1.52.1.6.1.2.1.1.1.4 | ColumnfnbBypass | read-write | mandatory | Denotes the bypass status of the current Token Ring board. Bypassed means the board is NOT attached to the FNB. |
| 1.3.6.1.4.1.52.1.6.1.2.1.1.1.5 | ColumnfnbRPBypass | read-write | mandatory | Denotes the Ring Port bypass status of the current Token Ring board. If this capability is not available on this board, the value 'other' is returned when read… |
| 1.3.6.1.4.1.52.1.6.1.2.2 | NodefnbCSMACD | |||
| 1.3.6.1.4.1.52.1.6.1.2.2.1 | TablefnbCSMACDTable | not-accessible | mandatory | A list of entries that provide connection status of CSMA/CD subsystems, for the FNB. |
| 1.3.6.1.4.1.52.1.6.1.2.2.1.1 | RowfnbCSMACDEntry | not-accessible | mandatory | An entry in the fnbCSMACDTable containing objects that provide FNB connection status for a CSMA/CD subsystem. |
| 1.3.6.1.4.1.52.1.6.1.2.2.1.1.1 | ColumnfnbCSMACDIndex | read-write | mandatory | An unique value for each CSMACD subsystem. Its value ranges between 1 and chassisSlots. The value for each interface must remain constant, at least, from one r… |
| 1.3.6.1.4.1.52.1.6.1.2.2.1.1.2 | ColumnfnbConnect | read-write | mandatory | Denotes the connection status of the CSMA/CD board to the inter-RIC bus. |
| 1.3.6.1.4.1.52.1.6.1.2.2.1.1.3 | ColumnfnbPortChanges | read-only | mandatory | Denotes the number of times any port on the given MIM has changed it's connection to the inter-RIC bus. |
| 1.3.6.1.4.1.52.1.6.1.2.3 | NodefnbPortConnect | |||
| 1.3.6.1.4.1.52.1.6.1.2.3.1 | TablefnbPortConnectTable | not-accessible | mandatory | This table is used to control port association on ethernet devices. Only those boards that support port switching will be listed in this table. |
| 1.3.6.1.4.1.52.1.6.1.2.3.1.1 | RowfnbPortConnectEntry | not-accessible | mandatory | Describes a specific port connection entry. |
| 1.3.6.1.4.1.52.1.6.1.2.3.1.1.1 | ColumnfnbPortConnectBoardIndex | read-only | mandatory | An instance of a board for which this port assignment relationship exists. |
| 1.3.6.1.4.1.52.1.6.1.2.3.1.1.2 | ColumnfnbPortConnectPortIndex | read-only | mandatory | An instance of a port for which this assignment relationship exists. |
| 1.3.6.1.4.1.52.1.6.1.2.3.1.1.3 | ColumnfnbPortConnectPortAssignment | read-write | mandatory | The specific channel that the port is assigned. |
| 1.3.6.1.4.1.52.1.6.1.2.3.1.1.4 | ColumnfnbPortConnectCompID | read-only | mandatory | This is the component ID as defined in the chassis MIB that this port is associated with. These components will be repeater components. |
| 1.3.6.1.4.1.52.1.6.1.2.3.2 | ScalarfnbPortConnectionChanges | read-only | mandatory | Maintains the number of times any port within the mangement domain of this MIM changes it's port assignment. |
| 1.3.6.1.4.1.52.1.6.1.3 | Nodechassis | |||
| 1.3.6.1.4.1.52.1.6.1.3.1 | ScalarchassisHWRev | read-only | mandatory | Define the hardware revision of the device or sys- tem chassis. |
| 1.3.6.1.4.1.52.1.6.1.3.2 | ScalarchassisType | read-only | mandatory | Denotes the type of chassis. |
| 1.3.6.1.4.1.52.1.6.1.3.3 | ScalarchassisSlots | read-only | mandatory | Denotes the number of available chassis slots. |
| 1.3.6.1.4.1.52.1.6.1.3.4 | ScalarchassisFNB | read-only | mandatory | Denotes the presence or absence of the FNB. |
| 1.3.6.1.4.1.52.1.6.1.3.5 | ScalarchassisAlarmEna | read-write | mandatory | Allow an audible alarm to be either enabled or dis- abled. |
| 1.3.6.1.4.1.52.1.6.1.3.6 | ScalarchassisAlarmState | read-write | mandatory | Denotes the current condition of the power supply fault detection circuit. Setting a value of chassisNoFaultCondition(1) disables the current chassis alarm con… |
| 1.3.6.1.4.1.52.1.6.1.4 | Nodeenvironment | |||
| 1.3.6.1.4.1.52.1.6.1.4.1 | TablepowerTable | not-accessible | mandatory | A list of power supply entries. |
| 1.3.6.1.4.1.52.1.6.1.4.1.1 | RowpowerEntry | not-accessible | mandatory | An entry in the powerTable providing objects for a power supply. |
| 1.3.6.1.4.1.52.1.6.1.4.1.1.1 | ColumnpowerSupplyNum | read-only | mandatory | Denotes the power supply that may have failed. |
| 1.3.6.1.4.1.52.1.6.1.4.1.1.2 | ColumnpowerSupplyState | read-only | mandatory | Denotes the power supply's state. |
| 1.3.6.1.4.1.52.1.6.1.4.1.1.3 | ColumnpowerSupplyId | read-only | mandatory | Identifies the type of power supply. For example, this could be used to identify power supplies which support additional remote management capabilities. |
| 1.3.6.1.4.1.52.1.6.1.4.1.1.4 | ColumnpowerSupplyRedun | read-only | mandatory | Identifies whether power redundancy is available within the chassis. Devices that do not support power supply redundancy, will return infoNotAvailable. |
| 1.3.6.1.4.1.52.1.6.1.4.1.1.5 | ColumnpowerSupplyRemoteDisable | read-write | mandatory | Provides Enable/Disable control of the power supply. For devices that do not support this capability, a set attempt will return BADVALUE, and a read will alway… |
| 1.3.6.1.4.1.52.1.6.2.3 | NodenB55 | |||
| 1.3.6.1.4.1.52.1.6.2.3.1 | ScalarnB55HWAddress | read-only | mandatory | The device's MAC address. |
| 1.3.6.1.4.1.52.1.6.2.3.2 | ScalarnB55HWRev | read-only | mandatory | Denotes the revision of the nB55 board. A value of one denotes Revision 1, a value of two denotes Revi- sion 2, and so on. |
| 1.3.6.1.4.1.52.1.6.2.3.3 | ScalarnB55FWRev | read-only | mandatory | Denotes the revision of firmware in the module. The first octets provides the version, and the second provides the revision. |
| 1.3.6.1.4.1.52.1.6.2.6 | NodemRXI | |||
| 1.3.6.1.4.1.52.1.6.2.6.1 | ScalarmRXIHWAddress | read-only | mandatory | The device's MAC address. |
| 1.3.6.1.4.1.52.1.6.2.6.2 | ScalarmRXIHWRev | read-only | mandatory | Denotes the revision of the mRXI board. A value of one denotes Revision 1, a value of two denotes Revi- sion 2, and so on. |
| 1.3.6.1.4.1.52.1.6.2.6.3 | ScalarmRXIFWRev | read-only | mandatory | Denotes the revision of firmware in the module. The first octets provides the version, and the second provides the revision. |
| 1.3.6.1.4.1.52.1.6.2.7 | NodeiRM3 | |||
| 1.3.6.1.4.1.52.1.6.2.7.1 | ScalariRM3HWAddress | read-only | mandatory | The device's MAC address. |
| 1.3.6.1.4.1.52.1.6.2.7.2 | ScalariRM3HWRev | read-only | mandatory | Denotes the revision of the IRM3 board. A value of one denotes Revision 1, a value of two denotes Revi- sion 2, and so on. |
| 1.3.6.1.4.1.52.1.6.2.7.3 | ScalariRM3FWRev | read-only | mandatory | Denotes the revision of firmware in the module. The first octets provides the version, and the second provides the revision. |
| 1.3.6.1.4.1.52.1.6.2.7.4 | ScalariRM3PortAssoc | read-write | mandatory | Controls how front panel ports are associated with the Irm3. |
| 1.3.6.1.4.1.52.1.6.2.7.5 | ScalariRM3BPSupport | read-only | mandatory | Denotes whether or not Backplane Protocol Support is present in the current version of the IRM3. |
| 1.3.6.1.4.1.52.1.6.2.8 | NodetRMM | |||
| 1.3.6.1.4.1.52.1.6.2.8.1 | ScalartRMMHWAddress | read-only | mandatory | The device's MAC address. |
| 1.3.6.1.4.1.52.1.6.2.8.2 | ScalartRMMHWRev | read-only | mandatory | Denotes the revision of the tRMM board. A value of one denotes Revision 1, a value of two denotes Revi- sion 2, and so on. |
| 1.3.6.1.4.1.52.1.6.2.8.3 | ScalartRMMFWRev | read-only | mandatory | Denotes the revision of firmware in the module. The first octets provides the version, and the second provides the revision. |
| 1.3.6.1.4.1.52.1.6.2.9 | NodeeMME | |||
| 1.3.6.1.4.1.52.1.6.2.9.1 | ScalareMMEHWAddress | read-only | mandatory | The device's MAC address. |
| 1.3.6.1.4.1.52.1.6.2.9.2 | ScalareMMEHWRev | read-only | mandatory | Denotes the revision of the eMME board. A value of one denotes Revision 1, a value of two denotes Revi- sion 2, and so on. |
| 1.3.6.1.4.1.52.1.6.2.9.3 | ScalareMMEFWRev | read-only | mandatory | Denotes the revision of firmware in the module. The first octets provides the version, and the second provides the revision. |
| 1.3.6.1.4.1.52.1.6.2.9.4 | ScalareMMEBoardMap | read-only | mandatory | Denotes a bit encoded representation of the slots that contain MIM boards. If a bit is a one then the board is present. |
| 1.3.6.1.4.1.52.1.6.2.10 | NodefPRedundancy | |||
| 1.3.6.1.4.1.52.1.6.2.10.1 | NodefPRedund | |||
| 1.3.6.1.4.1.52.1.6.2.10.1.1 | ScalarfPRedundReset | read-write | mandatory | If this object is set to Reset it will cause a reset of the front panel redundancy. Setting this object to NoReset will do nothing. This object will always be … |
| 1.3.6.1.4.1.52.1.6.2.10.1.2 | ScalarfPRedundPollInterval | read-write | mandatory | Get/Set the number of seconds between polls for front panel redundancy. |
| 1.3.6.1.4.1.52.1.6.2.10.1.3 | ScalarfPRedundRetrys | read-write | mandatory | Get/Set the the number of unanswered polls allowed for the front panel redundancy before it switches ports. |
| 1.3.6.1.4.1.52.1.6.2.10.1.4 | ScalarfPRedundNumAddr | read-only | mandatory | Get the number of IP Addresses associated with front panel redundancy. |
| 1.3.6.1.4.1.52.1.6.2.10.1.5 | ScalarfPRedundAddAddr | read-write | mandatory | Add an IP Address to the polling list for the front panel redundancy. |
| 1.3.6.1.4.1.52.1.6.2.10.1.6 | ScalarfPRedundDelAddr | read-write | mandatory | Delete an IP Address from the polling list for the front panel redundancy. |
| 1.3.6.1.4.1.52.1.6.2.10.1.7 | ScalarfPRedundActivePort | read-write | mandatory | Get/Set the front panel port you want to be active when front panel redundancy is enabled. |
| 1.3.6.1.4.1.52.1.6.2.10.1.8 | ScalarfPRedundEnable | read-write | mandatory | If this object is set to enable, the front panel redundancy will be activated. If this object is set to disable, the front panel redundancy will be deactivated… |
| 1.3.6.1.4.1.52.1.6.2.10.2 | TablefPRedundAddrTable | not-accessible | mandatory | A list of entries that provide IP address information for front panel redundancy. |
| 1.3.6.1.4.1.52.1.6.2.10.2.1 | RowfPRedundAddrEntry | not-accessible | mandatory | An entry in the fPRedundAddrTable providing objects for front panel redundancy. |
| 1.3.6.1.4.1.52.1.6.2.10.2.1.1 | ColumnfPRedundAddrId | read-only | mandatory | A unique value identifying an element in a sequence of member IP Addresses which belong to the front panel redundancy. This value goes from 1 to the maximum nu… |
| 1.3.6.1.4.1.52.1.6.2.10.2.1.2 | ColumnfPRedundAddrIPAddr | read-only | mandatory | Returns an IP Address associated with the front panel redundancy. |
| 1.3.6.1.4.1.52.1.6.3.1 | NodeupsVersion | |||
| 1.3.6.1.4.1.52.1.6.3.1.1 | NodeupsRevision | |||
| 1.3.6.1.4.1.52.1.6.3.1.1.1 | ScalarupsID | read-write | mandatory | Denotes a type code which refers to the manufactur- ers and model of the UPS. |
| 1.3.6.1.4.1.52.1.6.3.1.1.2 | ScalarupsUpTime | read-only | mandatory | Denotes the operating time, in hours, since the UPS was last powered on. |
| 1.3.6.1.4.1.52.1.6.3.1.1.3 | ScalarupsDisable | read-write | deprecated | Allows the UPS to be disabled. A set turns of the UPS for those systems, so equipped. A get/get-next always returns 0. |
| 1.3.6.1.4.1.52.1.6.3.1.1.4 | ScalarupsDisconnect | read-write | mandatory | Allows the UPS backup power system to conserve its battery. Setting the object to a value of 1 turns off the power system. A get/get-next always retuns a 0. |
| 1.3.6.1.4.1.52.1.6.3.1.1.5 | ScalarupsTest | read-write | mandatory | Denotes the status performed on the UPS. A write unitOK(1) intiates the test. A read indicates status of test. |
| 1.3.6.1.4.1.52.1.6.3.1.1.6 | ScalarupsBatteryCapacity | read-only | mandatory | Denotes the percentage of battery capacity left, 100% being a fully-charged battery. |
| 1.3.6.1.4.1.52.1.6.3.1.1.7 | ScalarupsACLineVoltsIn | read-only | mandatory | Denotes the input AC utility line voltage. |
| 1.3.6.1.4.1.52.1.6.3.1.1.8 | ScalarupsBatteryVoltsOut | read-only | mandatory | Denotes the battery voltage. |
| 1.3.6.1.4.1.52.1.6.4.1 | ScalardlForceOnBoot | read-write | mandatory | When set to a 1, the system will request a download, during the next system restart. If no server is found and the current image in flash memory is valid, the … |
| 1.3.6.1.4.1.52.1.6.4.2 | ScalardlCommitRAMToFlash | read-write | mandatory | When written with a 1, the boot software will erase flash memory, compress the downloaded code, and save the compressed image into flash memory. Upon com- plet… |
| 1.3.6.1.4.1.52.1.6.4.3 | ScalardlInitiateColdBoot | read-write | mandatory | When written with a 1, the boot software intiates a system reboot. All MIB variables used to control the exact nature of the download should be set, prior to a… |
| 1.3.6.1.4.1.52.1.6.4.4 | ScalardlTFTPRequestHost | read-write | mandatory | The IP address of the server to be used, when firmware is to be loaded across the network. |
| 1.3.6.1.4.1.52.1.6.4.5 | ScalardlTFTPRequest | read-write | mandatory | The filename requested of the server, when firmware is to be loaded across the network. |
| 1.3.6.1.4.1.52.1.6.4.6 | ScalardlLastImageFilename | read-only | mandatory | Filename of the last image to be successfully loaded into memory. |
| 1.3.6.1.4.1.52.1.6.4.7 | ScalardlLastServerIPAddress | read-only | mandatory | The IP address of the server used to load the present image in flash memory. |
| 1.3.6.1.4.1.52.1.6.4.8 | ScalardlFlashSize | read-only | mandatory | Denotes the size, in bytes, of flash memory con- tained on this module. |
| 1.3.6.1.4.1.52.1.6.4.9 | ScalardlFlashCount | read-only | mandatory | Denotes the number of times that flash memory has been reprogrammed. This value is initialzed to 1, when the module is initially powered up. |
| 1.3.6.1.4.1.52.1.6.4.10 | ScalardlFirmwareBase | read-only | mandatory | Denotes the starting address of the firmware in RAM. |
| 1.3.6.1.4.1.52.1.6.4.11 | ScalardlFirmwareTop | read-only | mandatory | Denotes the ending address of firmware in RAM. |
| 1.3.6.1.4.1.52.1.6.4.12 | ScalardlFirmwareStart | read-only | mandatory | Denotes the start address of the firmware, in RAM, as established by the boot process. |
| 1.3.6.1.4.1.52.1.6.4.13 | ScalardlBootRev | read-only | mandatory | Denotes the revision of boot firmware in the module. The first octets provides the version, and the second provides the revision. |
| 1.3.6.1.4.1.52.1.6.4.14 | ScalardlForceBootp | read-write | mandatory | When set, this variable forces the client to send a BOOTP request packet when rebooting. The client will make several attempts before timing out if a server do… |
| 1.3.6.1.4.1.52.1.6.4.15 | ScalardlServerName | read-write | mandatory | This OID is reserved for future use of the Bootp server name. This field can be used when a client wants to get boot information from a particular bootp server. |
| 1.3.6.1.4.1.52.1.6.4.16 | ScalardlOnLineDownLoad | read-write | mandatory | During normal operation this object has the value of 1. By setting this object to a value of forceDownLoad(2) an online download will be performed. By setting … |
| 1.3.6.1.4.1.52.1.6.4.17 | ScalardlOperStatus | read-only | mandatory | This object reflects the status of the download code. A value of normalOperation(3) reflects either a down load was started but has finished normally and no re… |
| 1.3.6.1.4.1.52.1.6.4.18 | ScalardlNetAddress | read-write | mandatory | IP Address of the server to be used when an image is to be downloaded using the Runtime TFTP Download. |
| 1.3.6.1.4.1.52.1.6.4.19 | ScalardlFileName | read-write | mandatory | Filename requested of the server when an image is to be downloaded using the Runtime TFTP Download. This should be a complete path filename. |
| 1.3.6.1.4.1.52.1.6.4.20 | ScalardlErrorString | read-only | mandatory | If the value of ctDLOperStatus is downloadCompleteError(5) then this object will provide a more complete description of the error. Otherwise this object will b… |
| 1.3.6.1.4.1.52.1.6.4.21 | ScalardlTftpServerGatewayIPAddress | read-write | mandatory | The IP address of the gateway/router which connects this SNMP agent to the TFTP server. |