CTRON-DECIV-ROUTER-MIB
214 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter Gauge TimeTicks |
| RFC1213-MIB | DisplayString |
| ROUTER-OIDS | nwRtrProtoSuites |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.52.4.2.2.2.3.3 | NodenwDecIVRouter | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.1 | NodenwDecIVMibs | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.1.1 | ScalarnwDecIVMibRevText | read-only | mandatory | Indicates the current revision level of the DECnet Phase IV MIB in textual format. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2 | NodenwDecIVComponents | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1 | NodenwDecIVSystem | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1 | NodenwDecIVSysConfig | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.1 | ScalarnwDecIVSysRouterId | read-write | mandatory | The DECnet Address used to uniquely identify the host (device) running DECnet Phase IV Routing Services. Since DECnet Phase IV uses a single address to identif… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.2 | ScalarnwDecIVNodeType | read-write | mandatory | Specifies the node type. Setting this value to 2, (routing-iv), establishes the Routing Services-enabled device as a DECnet Level 1, intra-area router. Setting… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.3 | ScalarnwDecIVMaxNodes | read-write | mandatory | Specifies the maximum number of DECnet nodes allowed within an area. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.4 | ScalarnwDecIVMaxBRA | read-write | mandatory | Specifies the maximum number of router adjacencies supported by this node. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.5 | ScalarnwDecIVMaxBEA | read-write | mandatory | Specifies the maximum number of endnode adjacencies supported by this node. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.6 | ScalarnwDecIVMaxHops | read-write | mandatory | Specifies the maximum number of hops allowed for a valid route within the area. Any intra-area route consisting of a greater number of hops than specified by n… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.7 | ScalarnwDecIVMaxCost | read-write | mandatory | Specifies the maximum cost allowed for a valid route within the area. Any intra-area route with a cost greater than nwDecIVMaxCost is considered unreachable. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.8 | ScalarnwDecIVMaxVisits | read-write | mandatory | Specifies the maximum number of intra-area hops a packet can be forwarded. A packet is dropped once it has been forwarded nwDecIVMaxVisits. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.9 | ScalarnwDecIVNonBroadcastTimer | read-write | mandatory | Specifies the periodic interval (in seconds) at which DECnet Routing Services advertises its route table, on any non-broadcast networks attached to any router … |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.10 | ScalarnwDecIVBroadcastTimer | read-write | mandatory | Specifies the periodic interval (in seconds) at which DECnet Routing Services advertises its route table on any multi-access broadcast networks attached to any… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.11 | ScalarnwDecIVAreas | read-write | mandatory | Specifies the maximum number of areas allowed within a Level 2 (inter-area)routing domain. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.12 | ScalarnwDecIVMaxAreaHops | read-write | mandatory | Specifies the maximum number of areas that can be hopped by a valid inter-area route. Any inter-area route requiring a greater number of areas to be hopped tha… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.13 | ScalarnwDecIVMaxAreaCost | read-write | mandatory | Specifies the maximum cost allowed for a valid Level 2 (inter-area) route. Any inter-area route with a cost greater than nwDecIVMaxAreaCost is considered unrea… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2 | NodenwDecIVSysAdministration | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.1 | ScalarnwDecIVSysAdminStatus | read-write | mandatory | Sets the administrative state of DECnet Phase IV Routing Services, system-wide. Enabled (3) causes DECnet Phase IV system-wide Routing Services to become activ… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.2 | ScalarnwDecIVSysOperStatus | read-only | mandatory | Indicates the current operating condition of DECnet Phase IV Routing Services system-wide. The value of nwDecIVSysOperStatus indicates any problem with your DE… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.3 | ScalarnwDecIVSysAdminReset | read-write | mandatory | Resets DECnet Phase IV Routing Services, system-wide. Reset (2) forces a restart of DECnet Phase IV Routing Services without a graceful shutdown on any active … |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.4 | ScalarnwDecIVSysOperationalTime | read-only | mandatory | Indicates the elapsed time, in hundredths of a second, that nwDecIVSysOperStatus has been in it's current state. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.5 | ScalarnwDecIVSysVersion | read-only | mandatory | Indicates the current revision level of the DECnet Phase IV Routing Services firmware, in textual format. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2 | NodenwDecIVForwarding | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1 | NodenwDecIVFwdSystem | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1 | NodenwDecIVFwdCounters | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.1 | ScalarnwDecIVFwdCtrAdminStatus | read-write | mandatory | Sets the administrative state of the aggregate (system-wide) DECnet packet and byte counters. Enabled (3) causes these counters to become active. Disabled (2) … |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.2 | ScalarnwDecIVFwdCtrReset | read-write | mandatory | Resets the aggregate (system-wide) DECnet packet and byte counters. Reset (2) resets the DECnet aggregate counters to 0. nwDecIVFwdCtrOperationalTime is also r… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.3 | ScalarnwDecIVFwdCtrOperationalTime | read-only | mandatory | Indicates the elapsed time, in hundredths of a second, that DecIVFwdCtrOperStatus has been in the current state. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.4 | ScalarnwDecIVFwdCtrInPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been received, system-wide, during nwDecIVFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.5 | ScalarnwDecIVFwdCtrOutPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been transmitted, system-wide, during nwDecIVFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.6 | ScalarnwDecIVFwdCtrFwdPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been forwarded, system-wide, during nwDecIVFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.7 | ScalarnwDecIVFwdCtrFilteredPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been administratively filtered, system-wide, during nwDecIVFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.8 | ScalarnwDecIVFwdCtrDiscardPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been discarded, system-wide, during nwDecIVFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.9 | ScalarnwDecIVFwdCtrAddrErrPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been discarded, system-wide, during nwDecIVFwdCtrOperationalTime, because of addressing errors in the DE… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.10 | ScalarnwDecIVFwdCtrLenErrPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been discarded, system-wide, during nwDecIVFwdCtrOperationalTime, because an invalid packet length is co… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.11 | ScalarnwDecIVFwdCtrHdrErrPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been discarded, system-wide, during nwDecIVFwdCtrOperationalTime, because of an invalid DECnet header. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.12 | ScalarnwDecIVFwdCtrInBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet packets that have been received, system-wide, during nwDecIVFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.13 | ScalarnwDecIVFwdCtrOutBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet packets that have been transmitted, system-wide, during nwDecIVFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.14 | ScalarnwDecIVFwdCtrFwdBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet packets that have been forwarded, system-wide, during nwDecIVFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.15 | ScalarnwDecIVFwdCtrFilteredBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet packets that have been administratively filtered, system-wide, during nwDecIVFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.16 | ScalarnwDecIVFwdCtrDiscardBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet packets that have been discarded, system wide, during nwDecIVFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.17 | ScalarnwDecIVFwdCtrHostInPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been successfully delivered to the local host, during nwDecIVFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.18 | ScalarnwDecIVFwdCtrHostOutPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been transmitted by the local host, during nwDecIVFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.19 | ScalarnwDecIVFwdCtrHostDiscardPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been discarded by the local host, during nwDecIVFwdCtrOperationalTime, due to a lack of host resources. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.20 | ScalarnwDecIVFwdCtrHostInBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet packets that have been received by the local host, during nwDecIVFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.21 | ScalarnwDecIVFwdCtrHostOutBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet packets that have been transmitted by the local host, during nwDecIVFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.22 | ScalarnwDecIVFwdCtrHostDiscardBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet packets that have been discarded by the local host, during nwDecIVFwdCtrOperationalTime, due to a lack of hos… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2 | NodenwDecIVFwdInterfaces | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1 | NodenwDecIVFwdIfConfig | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1 | TablenwDecIVFwdIfTable | not-accessible | mandatory | This table contains an entry for each router port. This table is indexed by nwDecIVFwdIfIndex, which indicates the value of MIB 2 ifIndex, which identifies the… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1 | RownwDecIVFwdIfEntry | not-accessible | mandatory | Each entry specifies the DECnet Phase IV Routing Services configuration for the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.1 | ColumnnwDecIVFwdIfIndex | read-only | mandatory | Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.2 | ColumnnwDecIVFwdIfAdminStatus | read-write | mandatory | Sets the administrative state of DECnet Phase IV Routing Services on the router port for which the entry exists. Enabled (3) causes DECnet Phase IV Routing Ser… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.3 | ColumnnwDecIVFwdIfOperStatus | read-only | mandatory | Indicates the current operating condition of DECnet Phase IV Routing Services on the router port for which the entry exists. The value of nwDecIVFwdIfOperStatu… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.4 | ColumnnwDecIVFwdIfOperationalTime | read-only | mandatory | Indicates the elapsed time, in hundredths of a second, that nwDecIVFwdIfOperStatus has been in its current state. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.5 | ColumnnwDecIVFwdIfControl | read-write | mandatory | This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the C… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.6 | ColumnnwDecIVFwdIfMtu | read-write | mandatory | Specifies the Maximum Transmission Unit (MTU) for DECnet packets on the router port for which the entry exists. This includes the DECnet header and data, but d… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.7 | ColumnnwDecIVFwdIfForwarding | read-write | mandatory | Controls the forwarding of DECnet packets on the router port for which the entry exists. Enabled (3) causes DECnet packets to be forwarded. Disabled (2) preven… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.8 | ColumnnwDecIVFwdIfFrameType | read-write | mandatory | Specifies the framing type for DECnet packets forwarded on the router port for which the entry exists. Some frame types are only valid for specific media types… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.9 | ColumnnwDecIVFwdIfAclIdentifier | read-write | mandatory | Specifies the Access Control ID of the access control list in effect for DECnet packets being routed on the router port for which the entry exists. A value of … |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.10 | ColumnnwDecIVFwdIfAclStatus | read-write | mandatory | Controls the operation of any access control list configured for DECnet traffic on the router port for which the entry exists. Enabled (3) applies the access c… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.11 | ColumnnwDecIVFwdIfCacheControl | read-write | mandatory | This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Ca… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.12 | ColumnnwDecIVFwdIfCacheEntries | read-only | mandatory | This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Ca… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.13 | ColumnnwDecIVFwdIfCacheHits | read-only | mandatory | This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Ca… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.14 | ColumnnwDecIVFwdIfCacheMisses | read-only | mandatory | This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Ca… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2 | NodenwDecIVFwdIfCounters | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1 | TablenwDecIVFwdIfCtrTable | not-accessible | mandatory | This table contains an entry for each router port configured and enabled for DECnet Phase IV Routing Services. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1 | RownwDecIVFwdIfCtrEntry | not-accessible | mandatory | Each entry indicates the current packet and byte count of DECnet packets on each router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.1 | ColumnnwDecIVFwdIfCtrIfIndex | read-only | mandatory | Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.2 | ColumnnwDecIVFwdIfCtrAdminStatus | read-write | mandatory | Sets the administrative state of the per-port DECnet packet and byte counters on the router port for which the entry exists. Enabled (3) causes these counters … |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.3 | ColumnnwDecIVFwdIfCtrReset | read-write | mandatory | Resets the per-port DECnet packet and byte counters on the router port for which the entry exists. Reset (2) resets the counters to 0. nwDecIVFwdIfCtrOperation… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.4 | ColumnnwDecIVFwdIfCtrOperationalTime | read-only | mandatory | Indicates the elapsed time, in hundredths of a second, that the per-port DECnet packet and byte counters have been active on the router port for which the entr… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.5 | ColumnnwDecIVFwdIfCtrInPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been received, during nwDecIVFwdIfCtrOperationaltime, on the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.6 | ColumnnwDecIVFwdIfCtrOutPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been transmitted, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.7 | ColumnnwDecIVFwdIfCtrFwdPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been forwarded on the router port for which the entry exists, during nwDecIVFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.8 | ColumnnwDecIVFwdIfCtrFilteredPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been administratively filtered, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the … |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.9 | ColumnnwDecIVFwdIfCtrDiscardPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been discarded (dropped), during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry … |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.10 | ColumnnwDecIVFwdIfCtrAddrErrPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been discarded because of addressing errors in the DECnet header, during nwDecIVFwdIfCtrOperationalTime,… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.11 | ColumnnwDecIVFwdIfCtrLenErrPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been discarded because an invalid packet length was contained in the DECnet header, during nwDecIVFwdIfC… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.12 | ColumnnwDecIVFwdIfCtrHdrErrPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been discarded because of an invalid DECnet header, during nwDecIVFwdIfCtrOperationalTime, on the router… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.13 | ColumnnwDecIVFwdIfCtrInBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet packets that have been received, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entr… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.14 | ColumnnwDecIVFwdIfCtrOutBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet packets that have been transmitted, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the e… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.15 | ColumnnwDecIVFwdIfCtrFwdBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet packets that have been forwarded, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the ent… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.16 | ColumnnwDecIVFwdIfCtrFilteredBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet packets that have been administratively filtered, during nwDecIVFwdIfCtrOperationalTime, on the router port f… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.17 | ColumnnwDecIVFwdIfCtrDiscardBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet packets that have been discarded, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the ent… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.18 | ColumnnwDecIVFwdIfCtrHostInPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been delivered to the local host, during nwDecIVFwdIfCtrOperationalTime, that were received on the route… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.19 | ColumnnwDecIVFwdIfCtrHostOutPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been transmitted by the local host, during nwDecIVFwdIfCtrOperationalTime, on the router port for which … |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.20 | ColumnnwDecIVFwdIfCtrHostDiscardPkts | read-only | mandatory | Indicates the total number of DECnet packets that have been discarded by the local host, during nwDecIVFwdIfCtrOperationalTime, that were received on the route… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.21 | ColumnnwDecIVFwdIfCtrHostInBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet packets that have been delivered to the local host, during nwDecIVFwdIfCtrOperationalTime, that were received… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.22 | ColumnnwDecIVFwdIfCtrHostOutBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet packets that have been transmitted by the local host, during nwDecIVFwdIfCtrOperationalTime, on the router po… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.23 | ColumnnwDecIVFwdIfCtrHostDiscardBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet packets that have been discarded by the local host, due to a lack of host resources, that were received on th… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4 | NodenwDecIVTopology | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1 | NodenwDecIVDistanceVector | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1 | NodenwDecIVProto | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1 | NodenwDecIVProtoSystem | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1 | NodenwDecIVProtoConfig | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.1 | ScalarnwDecIVProtoAdminStatus | read-write | mandatory | Sets the administrative state of the DECnet Phase IV distance-vector-based routing protocol system-wide. Enabled (3) causes the routing protocol to become acti… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.2 | ScalarnwDecIVProtoOperStatus | read-only | mandatory | Indicates the current operating condition of the DECnet Phase IV distance-vector-based routing protocol system-wide. The value of nwDecIVProtoOperStatus indica… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.3 | ScalarnwDecIVProtoAdminReset | read-write | mandatory | Resets the DECnet Phase IV distance-vector-based routing protocol. Reset (2) forces a system-wide restart of the protocol without a graceful shut-down on any a… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.4 | ScalarnwDecIVProtoOperationalTime | read-only | mandatory | Indicates the elapsed time, in hundredths of a second, that nwDecIVProtoOperStatus has been in current state. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.5 | ScalarnwDecIVProtoVersion | read-only | mandatory | Indicates the current revision level of the DECnet Phase IV distance-vector-based routing protocol firmware, in textual format. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.6 | ScalarnwDecIVProtoStackSize | read-write | mandatory | Specifies the stack size of the DECnet Phase IV distance-vector- based routing protocol thread. In order for a change of this value to take effect, the protoco… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.7 | ScalarnwDecIVProtoThreadPriority | read-write | mandatory | Specifies the run-time execution priority of the DECnet Phase IV distance-vector-based routing protocol thread. In order for a change of this value to take eff… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.8 | ScalarnwDecIVProtoDatabaseThreshold | read-write | mandatory | This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Ca… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.9 | ScalarnwDecIVProtoAgeOut | read-write | mandatory | This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Ca… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.10 | ScalarnwDecIVProtoHoldDown | read-write | mandatory | This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Ca… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2 | NodenwDecIVProtoCounters | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.1 | ScalarnwDecIVProtoCtrAdminStatus | read-write | mandatory | Sets the administrative state of the aggregate (system-wide) DECnet Phase IV distance-vector-based routing protocol packet and byte counters. Enabled (3) cause… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.2 | ScalarnwDecIVProtoCtrReset | read-write | mandatory | Resets the aggregate (system-wide) DECnet Phase IV distance-vector-based routing protocol packet and byte counters. Reset (2) resets the DECnet aggregate count… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.3 | ScalarnwDecIVProtoCtrOperationalTime | read-only | mandatory | Indicates the elapsed time, in hundredths of a second, that nwDecIVProtoCtrAdminStatus has been in it's current state. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.4 | ScalarnwDecIVProtoCtrInPkts | read-only | mandatory | Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been received, system-wide, during nwDecIVProtoCtrOperat… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.5 | ScalarnwDecIVProtoCtrOutPkts | read-only | mandatory | Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been transmitted, system-wide, during nwDecIVProtoCtrOpe… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.6 | ScalarnwDecIVProtoCtrFilteredPkts | read-only | mandatory | Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been administratively filtered, system-wide, during nwDe… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.7 | ScalarnwDecIVProtoCtrDiscardPkts | read-only | mandatory | Indicates the total number of the DECnet Phase IV distance-vector -based routing protocol packets that have been discarded, system-wide, during nwDecIVProtoCtr… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.8 | ScalarnwDecIVProtoCtrInBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet Phase IV distance-vector based routing protocol packets that have been received, system-wide, during nwDecIVP… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.9 | ScalarnwDecIVProtoCtrOutBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet Phase IV distance-vectorbased routing protocol packets that have been transmitted, system-wide, during nwDecI… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.10 | ScalarnwDecIVProtoCtrFilteredBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet Phase IV distance-vectorbased routing protocol packets that have been administratively filtered, system-wide,… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.11 | ScalarnwDecIVProtoCtrDiscardBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet Phase IV distance-vectorbased routing protocol packets that have been discarded system-wide, during nwDecIVPr… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2 | NodenwDecIVProtoInterface | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1 | NodenwDecIVProtoIfConfig | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1 | TablenwDecIVProtoIfTable | not-accessible | mandatory | This table contains an entry for each router port. Each entry can contain different values, allowing the routing protocol configuration to vary from router por… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1 | RownwDecIVProtoIfEntry | not-accessible | mandatory | Each entry contains the DECnet Phase IV distance-vector-based routing protocol configuration for the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.1 | ColumnnwDecIVProtoIfIndex | read-only | mandatory | Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.2 | ColumnnwDecIVProtoIfAdminStatus | read-write | mandatory | Sets the administrative state of the DECnet Phase IV distance-vector-based routing protocol on the router port for which the entry exists. Enabled (3) causes t… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.3 | ColumnnwDecIVProtoIfOperStatus | read-only | mandatory | Indicates the current operating condition of the DECnet Phase IV distance-vector-based routing protocol on the router port for which the entry exists. The valu… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.4 | ColumnnwDecIVProtoIfOperationalTime | read-only | mandatory | Indicates the elapsed time, in hundredths of a second, that nwDecIVProtoIfOperStatus has been in it`s current state. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.5 | ColumnnwDecIVProtoIfVersion | read-write | mandatory | Indicates the revision level of the DECnet Phase IV distance-vector-based routing protocol firmware on the router port for which the entry exists, in textual f… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.6 | ColumnnwDecIVProtoIfAdvertisement | read-write | mandatory | Sets the interval, in seconds, at which the DECnet Phase IV distance-vectorbased routing protocol advertises its route table on the router port for which the e… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.7 | ColumnnwDecIVProtoIfFloodDelay | read-write | mandatory | This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Ca… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.8 | ColumnnwDecIVProtoIfRequestDelay | read-write | mandatory | This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Ca… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.9 | ColumnnwDecIVProtoIfPriority | read-write | mandatory | Sets the priority of the DECnet Phase IV distance-vector-based routing protocol on the router port for which the entry exists. Within an area, the router with … |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.10 | ColumnnwDecIVProtoIfHelloTimer | read-write | mandatory | Sets the interval, in seconds, at which DECnet Phase IV distance-vector-based routing protocol sends Hello packets on the router port for which the entry exist… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.11 | ColumnnwDecIVProtoIfSplitHorizon | read-write | mandatory | This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Ca… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.12 | ColumnnwDecIVProtoIfPoisonReverse | read-write | mandatory | This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Ca… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.13 | ColumnnwDecIVProtoIfSnooping | read-write | mandatory | Controls the operation of DECnet Phase IV distance-vector-based routing protocol snooping on the router port. When snooping is enabled the DECnet Phase IV dist… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.14 | ColumnnwDecIVProtoIfType | read-only | mandatory | Indicates whether the directly connected network segment does or does not support broadcast media access. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.15 | ColumnnwDecIVProtoIfXmitCost | read-write | mandatory | Sets the cost of transmitting a packet on the network segment connected to the router port for which the entry exists. The DECnet Phase IV distance-vector-base… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.16 | ColumnnwDecIVProtoIfAclIdentifier | read-write | mandatory | Specifies the Access Control ID of the access control list in effect for DECnet Phase IV distance-vector-based routing protocol packets on the router port for … |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.17 | ColumnnwDecIVProtoIfAclStatus | read-write | mandatory | Controls the operation of the access control list identified by nwDecIVProtoIfAclIdentifier. Enabled (3) applies the access control list to all DECnet Phase IV… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2 | NodenwDecIVProtoIfCounters | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1 | TablenwDecIVProtoIfCtrTable | not-accessible | mandatory | This table contains an entry for each router port. This table is indexed by nwDecIVProtoIfCtrIfIndex which indicates the value of MIB2 ifindex, which identifie… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1 | RownwDecIVProtoIfCtrEntry | not-accessible | mandatory | Each entry indicates the current packet and byte count of DECnet Phase IV distance-vector-based routing protocol packets on the router port for which the entry… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.1 | ColumnnwDecIVProtoIfCtrIfIndex | read-only | mandatory | Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.2 | ColumnnwDecIVProtoIfCtrAdminStatus | read-write | mandatory | Sets the administrative state of the per-port DECnet Phase IV distance-vectorbased routing protocol packet and byte counters on the router port for which the e… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.3 | ColumnnwDecIVProtoIfCtrReset | read-write | mandatory | Resets the per-port DECnet Phase IV distance-vector-based routing protocol packet and byte counters on the router port for which the entry exists. Reset (2) re… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.4 | ColumnnwDecIVProtoIfCtrOperationalTime | read-only | mandatory | Indicates the elapsed time, in hundredths of a second, that nwDecIVProtoIfCtrAdminStatus has been in the current state. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.5 | ColumnnwDecIVProtoIfCtrInPkts | read-only | mandatory | Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been received, during nwDecIVProtoIfCtrOperationalTime, … |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.6 | ColumnnwDecIVProtoIfCtrOutPkts | read-only | mandatory | Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been transmitted, during nwDecIVProtoIfCtrOperationalTim… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.7 | ColumnnwDecIVProtoIfCtrFilteredPkts | read-only | mandatory | Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been administratively filtered, during nwDecIVProtoIfCtr… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.8 | ColumnnwDecIVProtoIfCtrDiscardPkts | read-only | mandatory | Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been discarded, during nwDecIVProtoIfCtrOperationalTime,… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.9 | ColumnnwDecIVProtoIfCtrInBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet Phase IV distance-vector-based routing protocol packets that have been received, during nwDecIVProtoIfCtrOper… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.10 | ColumnnwDecIVProtoIfCtrOutBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet Phase IV distance-vector-based routing protocol packets that have been transmitted, during nwDecIVProtoIfCtrO… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.11 | ColumnnwDecIVProtoIfCtrFilteredBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet Phase IV distance-vector-based routing protocol packets that have been administratively filtered, during nwDe… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.12 | ColumnnwDecIVProtoIfCtrDiscardBytes | read-only | mandatory | Indicates the total number of bytes in the DECnet packets that have been discarded, during nwDecIVProtoIfCtrOperationalTime, that were received on the router p… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.2 | NodenwDecIVLinkState | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.5 | NodenwDecIVFib | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1 | TablenwDecIVFibTable | not-accessible | mandatory | This table contains an entry for each route being used to forward DECnet data packets.. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1 | RownwDecIVFibEntry | not-accessible | mandatory | Each entry in the table describes a route to a particular DECnet destination network and node. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.1 | ColumnnwDecIVFibNodeId | read-only | mandatory | Contains the DECnet Address of the destination node of the route for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.2 | ColumnnwDecIVFibNextHopNodeId | read-write | mandatory | Contains the DECnet Address of the next hop router for the route for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.3 | ColumnnwDecIVFibNextHopIf | read-write | mandatory | Indicates the value of MIB 2 ifindex, which identifies the router port through which the route exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.4 | ColumnnwDecIVFibRouteType | read-write | mandatory | Indicates the status of the route. A value of 3 indicates that the destination is on the network segment that is directly connected to the router port identifi… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6 | NodenwDecIVEndSystems | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.1 | NodenwDecIVHostsSystem | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.2 | NodenwDecIVHostsInterfaces | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3 | NodenwDecIVHostsToMedia | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1 | TablenwDecIVHostMapTable | not-accessible | mandatory | The DecIV Address translation table used for mapping a DecIV address to a circuit identifier (if applicable), corresponding port number, and framing type. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1 | RownwDecIVHostMapEntry | not-accessible | mandatory | Each entry contains one DecIVAddress to circuit equivalence. Also provided is the framing required to converse with this host, and the corresponding logical po… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.1 | ColumnnwDecIVHostMapIfIndex | read-only | mandatory | This is the primary (major) index into the DecIV HostMap table. This number corresponds to the index into the MIB-2 Interfaces Group which describes the DecIV … |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.2 | ColumnnwDecIVHostMapDecIVAddr | read-only | mandatory | The DecIVAddress of the host on the corresponding interface and circuit (if applicable). |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.3 | ColumnnwDecIVHostMapType | read-write | mandatory | Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the nwDecIVHostMapTable. That is, it effectively dissasoc… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.4 | ColumnnwDecIVHostMapCircuitID | read-write | mandatory | The identifier for the virtual circuit present on the interface. On an interface configured for Frame Relay, this number is the DLCI for the DecIV Address at t… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.5 | ColumnnwDecIVHostMapFraming | read-write | mandatory | Specifies the framing type required to converse with the host for which this entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.6 | ColumnnwDecIVHostMapPortNumber | read-only | mandatory | The unique value for the logical port number. It's value ranges between 1 and a maximum value which is dependent on both the number of configured interfaces in… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7 | NodenwDecIVAccessControl | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.1 | ScalarnwDecIVAclValidEntries | read-only | mandatory | Indicates the number of valid entries that exist in the access control list table, nwDecIVAclTable. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2 | TablenwDecIVAclTable | not-accessible | mandatory | This table contains the access control list information for DECnet traffic. This table contains entries each of which specifies whether packet forwarding betwe… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1 | RownwDecIVAclEntry | not-accessible | mandatory | Each entry contains DECnet source/destination access information. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.1 | ColumnnwDecIVAclIdentifier | read-only | mandatory | This is the primary (major) index into the DECnet access control list table. This value identifies each access control list by a unique identifier, a number ar… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.2 | ColumnnwDecIVAclSequence | read-only | mandatory | This is the secondary (minor) index into the DECnet access control list table. This number corresponds to a sequence number used to order multiple entries with… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.3 | ColumnnwDecIVAclPermission | read-write | mandatory | Specifies whether access is allowed or denied between the source and destination address pair. Note that source and destination are interchangeable when bi-dir… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.4 | ColumnnwDecIVAclMatches | read-only | mandatory | Indicates the number of matches on this entry that have resulted in the permit/deny access restriction being applied as part of the forwarding process. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.5 | ColumnnwDecIVAclDestAddress | read-write | mandatory | Specifies the destination DECnet Address used to compare for matches on the access control list. Either the Area ID or Node ID of this address may be set to 0,… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.6 | ColumnnwDecIVAclSrcAddress | read-write | mandatory | Specifies the source DECnet Address used to compare for matches on the access control list. Either the Area ID or Node ID of this address may be set to a wildc… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.8 | NodenwDecIVFilters | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.9 | NodenwDecIVRedirector | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10 | NodenwDecIVEvent | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.1 | NodenwDecIVEventLogConfig | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.1.1 | ScalarnwDecIVEventAdminStatus | read-write | mandatory | Sets the administrative state of DECnet event logging. Enabled (3) causes the event log to become active. Disabled (2) causes the event log to become inactive. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.1.2 | ScalarnwDecIVEventMaxEntries | read-write | mandatory | Sets the maximum number of entries allowed in the event log table. When the number of entries reaches the value of nwDecIVEventMaxEntries, the first (oldest) e… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.1.3 | ScalarnwDecIVEventTraceAll | read-write | mandatory | Enabled (3) allows logging of all event types on all router ports for all protocols and components. Disabled (2) causes the filter table to specify which event… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2 | NodenwDecIVEventLogFilterTable | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1 | TablenwDecIVEventFilterTable | not-accessible | mandatory | This table contains and entry for each event filter configured for DECnet Phase IV Routing Services events. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1 | RownwDecIVEventFilterEntry | not-accessible | mandatory | Each entry describes an event filter which defines a particular type of event to be logged to the event log. The value of nwDecIVEventFltrProtocol indicates th… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.1 | ColumnnwDecIVEventFltrProtocol | read-only | mandatory | Indicates the value of the Cabletron Routing Services MIB nwRtgProtocolInstance or nwComponentRtgInstance which identifies the protocol involved in the event f… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.2 | ColumnnwDecIVEventFltrIfNum | read-only | mandatory | Specifies the router port involved in the event for which the event filter exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.3 | ColumnnwDecIVEventFltrControl | read-write | mandatory | Set this value to 3 to add the entry to the event filter table. Set this value to 2 to remove the entry from the event filter table. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.4 | ColumnnwDecIVEventFltrType | read-write | mandatory | This 6 bit mask specifies the types of events to be logged. By default all 6 bits are set to 1, indicating that all types of events are to be logged. Setting a… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.5 | ColumnnwDecIVEventFltrSeverity | read-write | mandatory | Specifies the level of severity an event must meet in order to be logged. Controls the amount of event logging by ignoring events of a lower priority than spec… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.6 | ColumnnwDecIVEventFltrAction | read-write | mandatory | Specifies how the events are to be logged. Logging to the `log' stores the events in the event log table (nwDecIVEventLogTable). Logging to'trap' sends events … |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3 | NodenwDecIVEventLogTable | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1 | TablenwDecIVEventTable | not-accessible | mandatory | This table contains an entry for each event that has been logged. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1 | RownwDecIVEventEntry | not-accessible | mandatory | Each entry contains the information about an event that has been logged to the event table. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.1 | ColumnnwDecIVEventNumber | read-only | mandatory | An ordinal value assigned to the event for which the log entry exists. nwDecIVEventNumber is assigned so that each event in the event log can be uniquely ident… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.2 | ColumnnwDecIVEventTime | read-only | mandatory | Indicates the time at which the event was logged to the event log. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.3 | ColumnnwDecIVEventType | read-only | mandatory | Indicates the type of event that was logged. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.4 | ColumnnwDecIVEventSeverity | read-only | mandatory | Indicates the severity that was assigned to the event. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.5 | ColumnnwDecIVEventProtocol | read-only | mandatory | Indicates the value of the Cabletron Routing Services MIB nwRtgProtocolInstance or nwComponentInstance which identifies the protocol or component that was invo… |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.6 | ColumnnwDecIVEventIfNum | read-only | mandatory | Indicates the router port that was involved in the event. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.7 | ColumnnwDecIVEventTextString | read-only | mandatory | Contains the actual text string that was logged. |
| 1.3.6.1.4.1.52.4.2.2.2.3.3.2.11 | NodenwDecIVWorkGroup |