CTRON-IP-ROUTER-MIB
355 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter Gauge IpAddress TimeTicks |
| RFC1213-MIB | DisplayString PhysAddress |
| ROUTER-OIDS | nwRtrProtoSuites |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.52.4.2.2.2.3.1 | NodenwIpRouter | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.1 | NodenwIpMibs | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.1.1 | ScalarnwIpMibRevText | read-only | mandatory | Indicates the current revision level of the IP MIB in textual format. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2 | NodenwIpComponents | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.1 | NodenwIpSystem | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.1.1 | NodenwIpSysConfig | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.1.1.1 | ScalarnwIpSysRouterId | read-write | mandatory | The IP Address used to uniquely identify the host (device) running IP Routing Services. The value of nwIpSysRouterId is equal to the highest IP Address in the … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.1.2 | NodenwIpSysAdministration | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.1.2.1 | ScalarnwIpSysAdminStatus | read-write | mandatory | Sets the administrative state of IP Routing Services system-wide. Enabled(3) causes IP Routing Services to become active on all router ports configured and ena… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.1.2.2 | ScalarnwIpSysOperStatus | read-only | mandatory | Indicates the operating condition of IP Routing Services, system-wide. The value of nwIpSysOperStatus indicates any problem with your IP Routing Services confi… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.1.2.3 | ScalarnwIpSysAdminReset | read-write | mandatory | Resets IP Routing Services, system-wide. Reset (2) forces a restart of IP Routing Services without a graceful shutdown on any active router ports, without affe… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.1.2.4 | ScalarnwIpSysOperationalTime | read-only | mandatory | Indicates the elapsed time, in hundredths of a second, that nwIpSysOperStatus has been in its current administrative state. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.1.2.5 | ScalarnwIpSysVersion | read-only | mandatory | Indicates the current revision level of the IP Routing Services firmware, in textual format. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2 | NodenwIpForwarding | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1 | NodenwIpFwdSystem | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1 | NodenwIpFwdCounters | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.1 | ScalarnwIpFwdCtrAdminStatus | read-write | mandatory | Sets the administrative state of the aggregate (system-wide) IP packet and byte counters. Enabled (3) causes these counters to become active. Disabled (2) caus… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.2 | ScalarnwIpFwdCtrReset | read-write | mandatory | Resets the aggregate (system-wide) IP packet and byte counters. Reset (2) resets the IP aggregate counters to 0. nwIpFwdCtrOperationalTime is also reset to 0. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.3 | ScalarnwIpFwdCtrOperationalTime | read-only | mandatory | Indicates the elapsed time, in hundredths of a second, that nwIpFwdCtrAdminStatus has been in the current state. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.4 | ScalarnwIpFwdCtrInPkts | read-only | mandatory | Indicates the total number of IP packets that have been received, system-wide, during nwIpFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.5 | ScalarnwIpFwdCtrOutPkts | read-only | mandatory | Indicates the total number of IP packets that have been transmitted, system-wide, during nwIpFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.6 | ScalarnwIpFwdCtrFwdPkts | read-only | mandatory | Indicates the total number of IP packets that have been forwarded, system-wide, during nwIpFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.7 | ScalarnwIpFwdCtrFilteredPkts | read-only | mandatory | Indicates the total number of IP packets that have been administratively filtered, system-wide, during nwIpFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.8 | ScalarnwIpFwdCtrDiscardPkts | read-only | mandatory | Indicates the total number of IP packets that have been discarded, system-wide, during nwIpFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.9 | ScalarnwIpFwdCtrAddrErrPkts | read-only | mandatory | Indicates the total number of IP packets that have been discarded, system-wide, during nwIpFwdCtrOperationalTime, because of addressing errors in the IP header. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.10 | ScalarnwIpFwdCtrLenErrPkts | read-only | mandatory | Indicates the total number of IP packets that have been discarded, system-wide, during nwIpFwdCtrOperationalTime, because an invalid packet length is contained… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.11 | ScalarnwIpFwdCtrHdrErrPkts | read-only | mandatory | Indicates the total number of IP packets that have been discarded, system-wide, during nwIpFwdCtrOperationalTime, because of an invalid IP header. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.12 | ScalarnwIpFwdCtrInBytes | read-only | mandatory | Indicates the total number of bytes in the IP packets that have been received, system-wide, during nwIpFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.13 | ScalarnwIpFwdCtrOutBytes | read-only | mandatory | Indicates the total number of bytes in the IP packets that have been transmitted, system-wide, during nwIpFwdOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.14 | ScalarnwIpFwdCtrFwdBytes | read-only | mandatory | Indicates the total number of bytes in the IP packets that have been forwarded, system-wide, during nwIpFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.15 | ScalarnwIpFwdCtrFilteredBytes | read-only | mandatory | Indicates the total number of bytes in the IP packets that have been administratively filtered, system-wide, during nwIpFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.16 | ScalarnwIpFwdCtrDiscardBytes | read-only | mandatory | Indicates the total number of bytes in the IP packets that have been discarded, system-wide, during nwIpFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.17 | ScalarnwIpFwdCtrHostInPkts | read-only | mandatory | Indicates the total number of IP packets that have been successfully delivered to the local host, during nwIpFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.18 | ScalarnwIpFwdCtrHostOutPkts | read-only | mandatory | Indicates the total number of IP packets that have been forwarded by the local host, during nwIpFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.19 | ScalarnwIpFwdCtrHostDiscardPkts | read-only | mandatory | Indicates the total number of IP packets that have been discarded by the local host, during nwIpFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.20 | ScalarnwIpFwdCtrHostInBytes | read-only | mandatory | Indicates the total number of IP packets that have been received by the local host, during nwIpFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.21 | ScalarnwIpFwdCtrHostOutBytes | read-only | mandatory | Indicates the total number of IP packets that have been transmitted by the local host, during nwIpFwdCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.1.1.22 | ScalarnwIpFwdCtrHostDiscardBytes | read-only | mandatory | Indicates the total number of bytes in the IP packets that have been discarded by the local host, during nwIpFwdCtrOperationalTime, due to a lack of host resou… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2 | NodenwIpFwdInterfaces | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1 | NodenwIpFwdIfConfig | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1 | TablenwIpFwdIfTable | not-accessible | mandatory | This table contains an entry for each router port. This table is indexed by nwIpFwdIfIndex, which indicates the value of MIB 2 ifindex which identifies the rou… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1 | RownwIpFwdIfEntry | not-accessible | mandatory | Each entry specifies the IP Routing Services configuration for the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.1 | ColumnnwIpFwdIfIndex | read-only | mandatory | Indicates the value of MIB 2 ifindex, which identifies the router port. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.2 | ColumnnwIpFwdIfAdminStatus | read-write | mandatory | Sets the administrative state of IP Routing Services on the router port for which the entry exists. Enabled (3) causes IP Routing Services to become active. Di… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.3 | ColumnnwIpFwdIfOperStatus | read-only | mandatory | Indicates the current operating condition of IP Routing Services on the router port for which the entry exists. The value of nwIpFwdIfOperStatus indicates any … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.4 | ColumnnwIpFwdIfOperationalTime | read-only | mandatory | Indicates the elapsed time, in hundredths of a second, that nwIpFwdIfOperStatus has been in its current state. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.5 | ColumnnwIpFwdIfControl | read-write | mandatory | This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the C… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.6 | ColumnnwIpFwdIfMtu | read-write | mandatory | Specifies the Maximum Transmission Unit (MTU) for IP packets on the router port for which the entry exists. This includes the IP header and data, but does not … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.7 | ColumnnwIpFwdIfForwarding | read-write | mandatory | Controls forwarding of IP packets on the router port for which the entry exists. Enabled (3) causes IP packets to be forwarded. Disabled (2) prevents IP packet… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.8 | ColumnnwIpFwdIfFrameType | read-write | mandatory | Specifies the framing type for IP packets forwarded on the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.9 | ColumnnwIpFwdIfAclIdentifier | read-write | mandatory | Specifies the Access Control ID of the access control list in effect for the IP packets being routed on the router port for which the entry exists. A value of … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.10 | ColumnnwIpFwdIfAclStatus | read-write | mandatory | Controls the operation of any access control list configured for IP traffic for the IP packets being routed on the router port for which the entry exists. Enab… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.11 | ColumnnwIpFwdIfCacheControl | read-write | mandatory | Controls IP Address caching on the router port for which the entry exists. IP Address caching speeds-up the switching process. When IP Addresses caching is ena… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.12 | ColumnnwIpFwdIfCacheEntries | read-only | mandatory | Indicates the number of entries in the IP Address cache on the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.13 | ColumnnwIpFwdIfCacheHits | read-only | mandatory | Indicates the number of times entries in the IP Address Cache have been used to provide the IP Address required to validate, filter, or forward an IP packet on… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.1.1.14 | ColumnnwIpFwdIfCacheMisses | read-only | mandatory | Indicates the number of times the IP Address required to validate, filter, or forward an IP packet on the router port was not found in the IP Address cache. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.2 | TablenwIpAddressTable | not-accessible | mandatory | This table contains an entry for each IP Address assigned to each router port. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.2.1 | RownwIpAddrEntry | not-accessible | mandatory | Each entry specifies the IP addressing information for the logical IP network for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.2.1.1 | ColumnnwIpAddrIfIndex | read-write | mandatory | Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.2.1.2 | ColumnnwIpAddrIfAddress | read-write | mandatory | This is the IP Address assigned to the logical IP network for which the entry exist. As multiple IP Addresses may be assigned to a single router port, all addr… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.2.1.3 | ColumnnwIpAddrIfControl | read-write | mandatory | Set this object to add or delete this entry from the table. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.2.1.4 | ColumnnwIpAddrIfAddrType | read-write | mandatory | Specifies whether the IP address, nwIpAddrIfAddress, is the primary, workgroup or secondary IP address for the IP router port for which the entry exists. A pri… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.2.1.5 | ColumnnwIpAddrIfMask | read-write | mandatory | Specifies the Subnet Mask for the logical IP network for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.1.2.1.6 | ColumnnwIpAddrIfBcastAddr | read-write | mandatory | Specifies the IP broadcast address type for the logical IP network for which the entry exists. A router port may be configured to send IP broadcasts using the … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2 | NodenwIpFwdIfCounters | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1 | TablenwIpFwdIfCtrTable | not-accessible | mandatory | This table contains an entry for each router port configured and enabled for IP Routing Services. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1 | RownwIpFwdIfCtrEntry | not-accessible | mandatory | Each entry indicates the packet and byte count of IP packets on the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.1 | ColumnnwIpFwdIfCtrIfIndex | read-only | mandatory | Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.2 | ColumnnwIpFwdIfCtrAdminStatus | read-write | mandatory | Sets the administrative state of the per-port IP packet and byte counters on the router port for which the entry exists. Enabled (3) causes these counters to b… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.3 | ColumnnwIpFwdIfCtrReset | read-write | mandatory | Resets the per-port IP packet and byte counters on the router port for which the entry exists. Reset (2) resets the counters to 0. nwIpFwdIfCtrOperationalTime … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.4 | ColumnnwIpFwdIfCtrOperationalTime | read-only | mandatory | Indicates the elapsed time, in hundredths of a second, that the per-port IP packet and byte counters have been active on the router port for which the entry ex… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.5 | ColumnnwIpFwdIfCtrInPkts | read-only | mandatory | Indicates the total number of IP packets that have been received, during nwIpFwdIfCtrOperationaltime, on the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.6 | ColumnnwIpFwdIfCtrOutPkts | read-only | mandatory | Indicates the total number of IP packets that have been transmitted, during nwIpFwdIfCtrOperationalTime, on the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.7 | ColumnnwIpFwdIfCtrFwdPkts | read-only | mandatory | Indicates the total number of IP packets that have been forwarded during nwIpFwdIfCtrOperationalTime, on the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.8 | ColumnnwIpFwdIfCtrFilteredPkts | read-only | mandatory | Indicates the total number of IP packets that have been administratively filtered, during nwIpFwdIfCtrOperationalTime, on the IP router port for which this ent… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.9 | ColumnnwIpFwdIfCtrDiscardPkts | read-only | mandatory | Indicates the total number of IP packets that have been discarded (dropped), during nwIpFwdIfCtrOperationalTime, on the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.10 | ColumnnwIpFwdIfCtrAddrErrPkts | read-only | mandatory | Indicates the total number of IP packets that have been discarded, because of addressing errors in the IP header, during nwIpFwdIfCtrOperationalTime, on the ro… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.11 | ColumnnwIpFwdIfCtrLenErrPkts | read-only | mandatory | Indicates the total number of IP packets that have been discarded, because an invalid packet length was contained in the IP header, during nwIpFwdIfCtrOperatio… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.12 | ColumnnwIpFwdIfCtrHdrErrPkts | read-only | mandatory | Indicates the total number of IP packets that have been discarded, because of an invalid IP header, during nwIpFwdIfCtrOperationalTime, on the router port for … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.13 | ColumnnwIpFwdIfCtrInBytes | read-only | mandatory | Indicates the total number of bytes in the IP packets that have been received, during nwIpFwdIfCtrOperationalTime, on the router port for which the entry exist… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.14 | ColumnnwIpFwdIfCtrOutBytes | read-only | mandatory | Indicates the total number of bytes in the IP packets that have been transmitted, during nwIpFwdIfCtrOperationalTime, on the router port for which the entry ex… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.15 | ColumnnwIpFwdIfCtrFwdBytes | read-only | mandatory | Indicates the total number of bytes in the IP packets that have been forwarded, on the router port for which the entry exists, during nwIpFwdIfCtrOperationalTi… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.16 | ColumnnwIpFwdIfCtrFilteredBytes | read-only | mandatory | Indicates the total number of bytes in the IP packets that have been administratively filtered, during nwIpFwdIfCtrOperationalTime, on the IP router port for w… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.17 | ColumnnwIpFwdIfCtrDiscardBytes | read-only | mandatory | Indicates the total number of bytes in the IP packets that have been discarded, during nwIpFwdIfCtrOperationalTime, on the router port for which the entry exis… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.18 | ColumnnwIpFwdIfCtrHostInPkts | read-only | mandatory | Indicates the total number of IP packets that have been successfully delivered to the local host, that were received on the router port for which the entry exi… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.19 | ColumnnwIpFwdIfCtrHostOutPkts | read-only | mandatory | Indicates the total number of IP packets that have been transmitted by the local host, during nwIpFwdIfCtrOperationalTime, on the router port for which the ent… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.20 | ColumnnwIpFwdIfCtrHostDiscardPkts | read-only | mandatory | Indicates the total number of IP packets discarded by the local host due to a lack of host resources, that were received on the router port for which the entry… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.21 | ColumnnwIpFwdIfCtrHostInBytes | read-only | mandatory | Indicates the total number of bytes in the IP packets that have been successfully delivered to the local host, that were received on the router port for which … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.22 | ColumnnwIpFwdIfCtrHostOutBytes | read-only | mandatory | Indicates the total number of bytes in the IP packets that have been transmitted by the local host, during nwIpFwdIfCtrOperationalTime, on the router port for … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.2.2.2.1.1.23 | ColumnnwIpFwdIfCtrHostDiscardBytes | read-only | mandatory | Indicates the total number of bytes in the IP packets that have been discarded by the local host due to a lack of host resources, that were received on the rou… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4 | NodenwIpTopology | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1 | NodenwIpDistanceVector | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1 | NodenwIpRip | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1 | NodenwIpRipSystem | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1 | NodenwIpRipConfig | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.1 | ScalarnwIpRipAdminStatus | read-write | mandatory | Sets the administrative state of the RIP routing protocol system-wide. Enabled (3) causes RIP to become active on all router ports configured and enabled for I… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.2 | ScalarnwIpRipOperStatus | read-only | mandatory | Indicates the current operating condition of the RIP routing protocol system-wide. The value of nwIpRipOperStatus indicates any problem with your RIP configura… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.3 | ScalarnwIpRipAdminReset | read-write | mandatory | Resets the RIP routing protocol. Reset (2) forces a system-wide restart of the protocol system-wide without a graceful shutdown on any active router ports. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.4 | ScalarnwIpRipOperationalTime | read-only | mandatory | Indicates the elapsed time, in hundredths of a second, that nwIpRipOperStatus, has been in its current state. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.5 | ScalarnwIpRipVersion | read-only | mandatory | Indicates the current revision level of the RIP routing protocol firmware, in textual format. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.6 | ScalarnwIpRipStackSize | read-write | mandatory | Specifies the stack size of the RIP routing protocol thread. In order for a change of this value to take effect, the protocol (nwIpRipAdminReset), IP Routing S… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.7 | ScalarnwIpRipThreadPriority | read-write | mandatory | Specifies the run-time execution priority of the RIP routing protocol thread. In order for a change of this value to take effect, RIP (nwIpRipAdminReset), IP R… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.8 | ScalarnwIpRipDatabaseThreshold | read-write | mandatory | Specifies the run-time maximum number of RIP entries that can be held in the RIP route table. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.9 | ScalarnwIpRipAgeOut | read-write | mandatory | Specifies the amount of time, in seconds, that an inactive route table entry will be allowed to remain in the RIP route table before it is aged-out. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.1.10 | ScalarnwIpRipHoldDown | read-write | mandatory | Specifies the amount of time (in seconds) to wait before removing an entry from the route table, after receiving an update indicating that the destination has … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2 | NodenwIpRipCounters | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.1 | ScalarnwIpRipCtrAdminStatus | read-write | mandatory | Sets the administrative state of the aggregate (system-wide) RIP routing protocol packet and byte counters. Enabled (3) causes these counters to become active.… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.2 | ScalarnwIpRipCtrReset | read-write | mandatory | Resets the aggregate (system-wide) RIP routing protocol packet and byte counters. Reset (2) resets the RIP aggregate counters to 0. nwIpRipCtrOperationalTime i… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.3 | ScalarnwIpRipCtrOperationalTime | read-only | mandatory | Indicates the elapsed time, in hundredths of a second, that nwIpRipCtrAdminStatus has been in the current state. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.4 | ScalarnwIpRipCtrInPkts | read-only | mandatory | Indicates the total number of RIP packets that have been received, system-wide, during nwIpRipCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.5 | ScalarnwIpRipCtrOutPkts | read-only | mandatory | Indicates the total number of RIP packets that have been transmitted, system-wide, during nwIpRipCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.6 | ScalarnwIpRipCtrFilteredPkts | read-only | mandatory | Indicates the total number of RIP packets that have been administratively filtered, system-wide, during nwIpRipCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.7 | ScalarnwIpRipCtrDiscardPkts | read-only | mandatory | Indicates the total number of RIP packets that have been discarded, system-wide, during nwIpRipCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.8 | ScalarnwIpRipCtrInBytes | read-only | mandatory | Indicates the total number of bytes in the RIP packets that have been received, system-wide, during nwIpRipCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.9 | ScalarnwIpRipCtrOutBytes | read-only | mandatory | Indicates the total number of bytes in the RIP packets that have been transmitted, system-wide, during nwIpRipCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.10 | ScalarnwIpRipCtrFilteredBytes | read-only | mandatory | Indicates the total number of bytes in the RIP packets that have been administratively filtered, system-wide, during nwIpRipCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.1.2.11 | ScalarnwIpRipCtrDiscardBytes | read-only | mandatory | Indicates the total number of bytes in the RIP packets that have been discarded, system-wide, during nwIpRipCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2 | NodenwIpRipInterfaces | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1 | NodenwIpRipIfConfig | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1 | TablenwIpRipIfTable | not-accessible | mandatory | This table contains an entry for each router port. Each entry can contain different values, allowing the routing protocol configuration to vary from router por… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1 | RownwIpRipIfEntry | not-accessible | mandatory | Each entry contains the RIP routing protocol configuration for the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.1 | ColumnnwIpRipIfIndex | read-only | mandatory | Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.2 | ColumnnwIpRipIfAdminStatus | read-write | mandatory | Sets the administrative state of the RIP routing protocol on the router port for which the entry exists. Enabled (3) causes RIP to become active on the router … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.3 | ColumnnwIpRipIfOperStatus | read-only | mandatory | Indicates the current operating condition of the RIP routing protocol on the router port for which the entry exists. The value of nwIpRipIfOperStatus indicates… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.4 | ColumnnwIpRipIfOperationalTime | read-only | mandatory | Indicates the elapsed time, in hundredths of a second, nwIpRipIfOperStatus, has been in its current state. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.5 | ColumnnwIpRipIfVersion | read-write | mandatory | Indicates the revision level of the RIP routing protocol firmware on the router port for which the entry exists, in textual format. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.6 | ColumnnwIpRipIfAdvertisement | read-write | mandatory | Sets the interval, in seconds, at which RIP advertises the RIP route table on the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.7 | ColumnnwIpRipIfFloodDelay | read-write | mandatory | Sets the length of time, in seconds, that the RIP routing protocol should wait after discovering that a directly connected route has gone down, before flooding… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.8 | ColumnnwIpRipIfRequestDelay | read-write | mandatory | Sets the length of time, in hundredths of a second, that the RIP routing protocol should wait after receiving a route request packet, before sending a response… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.9 | ColumnnwIpRipIfPriority | read-write | mandatory | This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the C… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.10 | ColumnnwIpRipIfHelloTimer | read-write | mandatory | This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interfaced to all the … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.11 | ColumnnwIpRipIfSplitHorizon | read-write | mandatory | Sets the operating condition of Split Horizon on the router port for which the entry exists. When Split Horizon is enabled, the RIP routing protocol keeps trac… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.12 | ColumnnwIpRipIfPoisonReverse | read-write | mandatory | Sets the operating condition of Poison Reverse on the router port for which the entry exists. When Poison Reverse is enabled, the RIP routing protocol advertis… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.13 | ColumnnwIpRipIfSnooping | read-write | mandatory | Controls the operation of RIP Snooping on the router port. When RIP Snooping is enabled the RIP routing protocol operates in passive mode so that it receives r… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.14 | ColumnnwIpRipIfType | read-only | mandatory | Indicates whether the directly connected network segment does or does not support broadcast media access. If broadcast media access is supported, RIP advertise… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.15 | ColumnnwIpRipIfXmitCost | read-write | mandatory | This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the C… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.16 | ColumnnwIpRipIfAclIdentifier | read-write | mandatory | Specifies the Access Control ID of the access control list in effect for RIP routing protocol packets on the router port for which the entry exists. A value of… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.1.1.1.17 | ColumnnwIpRipIfAclStatus | read-write | mandatory | Controls the operation of the access control list identified by nwIpRipIfAclIdentifier. Enabled (3) applies the access control list to all RIP routing protocol… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2 | NodenwIpRipIfCounters | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1 | TablenwIpRipIfCtrTable | not-accessible | mandatory | This table contains an entry for each router port.This table is indexed by nwIpRipIfCtrIfIndex which indicates the value of MIB 2 ifindex, which identifies the… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1 | RownwIpRipIfCtrEntry | not-accessible | mandatory | Each entry indicates the current packet and byte count of RIP routing protocol packets on the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.1 | ColumnnwIpRipIfCtrIfIndex | read-only | mandatory | Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.2 | ColumnnwIpRipIfCtrAdminStatus | read-write | mandatory | Sets the administrative state of the RIP packet and byte counters on the router port for which this entry exists. Enabled (3) causes these counters to become a… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.3 | ColumnnwIpRipIfCtrReset | read-write | mandatory | Resets the per-port RIP packet and byte counters on the router port for which this entry exists. Reset (2) resets the counters to 0. nwIpRipIfCtrOperationalTim… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.4 | ColumnnwIpRipIfCtrOperationalTime | read-only | mandatory | Indicates the elapsed time, in hundredths of a second, that nwIpRipIfCtrAdminStatus has been in the current state. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.5 | ColumnnwIpRipIfCtrInPkts | read-only | mandatory | Indicates the total number of RIP routing protocol packets that have been received, during nwIpRipIfCtrOperationalTime, on the router port for which the entry … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.6 | ColumnnwIpRipIfCtrOutPkts | read-only | mandatory | Indicates the total number of RIP packets that have been transmitted, during nwIpRipIfCtrOperationalTime, on the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.7 | ColumnnwIpRipIfCtrFilteredPkts | read-only | mandatory | Indicates the total number of RIP packets that have been administratively filtered during nwIpRipIfCtrOperationalTime, on the router port for which the entry e… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.8 | ColumnnwIpRipIfCtrDiscardPkts | read-only | mandatory | Indicates the total number of RIP routing protocol packets that have been discarded, during nwIpRipIfCtrOperationalTime. that were received through the router … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.9 | ColumnnwIpRipIfCtrInBytes | read-only | mandatory | Indicates the total number of bytes in the RIP routing protocol packets that have been received, during nwIpRipIfCtrOperationalTime, on the router port for whi… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.10 | ColumnnwIpRipIfCtrOutBytes | read-only | mandatory | Indicates the total number of bytes in the RIP routing protocol packets that have been transmitted, during nwIpRipIfCtrOperationalTime, on the router port for … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.11 | ColumnnwIpRipIfCtrFilteredBytes | read-only | mandatory | Indicates the total number of bytes in the RIP routing protocol packets that have been administratively filtered, during nwIpRipIfCtrOperationalTime, on the ro… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.2.2.1.1.12 | ColumnnwIpRipIfCtrDiscardBytes | read-only | mandatory | Indicates the total number of bytes in the RIP routing protocol packets that have been discarded during nwIpRipIfCtrOperationalTime, that were received on the … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3 | NodenwIpRipDatabase | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1 | TablenwIpRipRouteTable | not-accessible | mandatory | This table contains the RIP route table. This table contains an entry for each route learned through the RIP routing protocol. Only the best routes from this t… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1.1 | RownwIpRipRouteEntry | not-accessible | mandatory | Each entry describes the RIP route to the destination network for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1.1.1 | ColumnnwIpRipRtNetId | read-only | mandatory | This is the primary index into the RIP route table. This number indicates the IP Address of the destination for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1.1.2 | ColumnnwIpRipRtIfIndex | read-only | mandatory | This is a secondary index into IP-RIP route table. This number corresponds to the value of MIB 2 ifindex, which identifies the router port for which the entry … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1.1.3 | ColumnnwIpRipRtSrcNode | read-only | mandatory | This is a secondary index into the RIP route table. This number indicates the IP Address of the source router from which this route was learned. A value of 0.0… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1.1.4 | ColumnnwIpRipRtMask | read-only | mandatory | Indicates the Subnet Mask of the IP Address for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1.1.5 | ColumnnwIpRipRtHops | read-only | mandatory | Indicates the number of hops required to reach the destination for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1.1.6 | ColumnnwIpRipRtAge | read-only | mandatory | Indicates the amount of time, in seconds, since an update has been received for the route for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1.1.7 | ColumnnwIpRipRtType | read-only | mandatory | Indicates whether the destination network is directly connected through the router port specified by nwIpRipRtIfIndex, or is indirectly connected through anoth… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.3.1.1.8 | ColumnnwIpRipRtFlags | read-only | mandatory | Specifies properties of the RIP route. The bit mask is as follows: source-changed (1), best-source (2), local net (4), net-down (8), update-fib-only (16). |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.1.1.4 | NodenwIpRipFilters | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2 | NodenwIpLinkState | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1 | NodenwIpOspf | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1 | NodenwIpOspfSystem | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.1 | NodenwIpOspfConfig | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.1.1 | ScalarnwIpOspfAdminStatus | read-write | mandatory | Sets the administrative state of the OSPF routing protocol. enabled(3) causes OSPF to become active on any IP configured router ports. disabled(2) causes OSPF … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.1.2 | ScalarnwIpOspfOperStatus | read-only | mandatory | Indicates the current operating condition of OSPF. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.1.3 | ScalarnwIpOspfAdminReset | read-write | mandatory | Resets OSPF. reset(2) will force a restart of OSPF on any active IP router ports, configured for OSPF, without a graceful shutdown, without affecting any other… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.1.4 | ScalarnwIpOspfOperationalTime | read-only | mandatory | Indicates the amount of time (#of time ticks) that OSPF has been in its current operational state. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.1.5 | ScalarnwIpOspfVersion | read-only | mandatory | Indicates the current Cabletron revision level of OSPF in textual format, not the OSPF version supported. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.1.6 | ScalarnwIpOspfStackSize | read-write | mandatory | Specifies the stack size for the OSPF thread. In order for a change of this value to take effect, OSPF (nwIpOspfAdminStatus), IP (nwIpSysAdminStatus), or the d… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.1.7 | ScalarnwIpOspfThreadPriority | read-write | mandatory | Specifies the run-time execution priority of the OSPF protocol thread. In order for a change of this value to take effect, OSPF or the IP routing services, or … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2 | NodenwIpOspfCounters | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.1 | ScalarnwIpOspfCtrAdminStatus | read-write | mandatory | Sets the operating condition of the aggregate (device-wide) OSPF packet and byte counters. enable (3) causes these counters to become active on any router port… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.2 | ScalarnwIpOspfCtrReset | read-write | mandatory | Resets the aggregate (device-wide) OSPF packet and byte counters. reset(2) resets the aggregate OSPF counters to 0 and nwIpOspfCtrOperationalTime to 0. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.3 | ScalarnwIpOspfCtrOperationalTime | read-only | mandatory | Indicates the amount of time (# of time ticks) that the aggregate OSPF packet and byte counters have been active. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.4 | ScalarnwIpOspfCtrInPkts | read-only | mandatory | Indicates the total number of OSPF packets that have been received, device-wide, during nwIpOspfCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.5 | ScalarnwIpOspfCtrOutPkts | read-only | mandatory | Indicates the total number of OSPF packets that have been transmitted, device-wide, during nwIpOspfCtr- Operational-Time. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.6 | ScalarnwIpOspfCtrFilteredPkts | read-only | mandatory | Indicates the total number of OSPF packets that have been administratively filtered, device-wide, during nwIpOspfCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.7 | ScalarnwIpOspfCtrDiscardPkts | read-only | mandatory | Indicates the total number of OSPF packets that have been discarded, device-wide, during nwIpOspfCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.8 | ScalarnwIpOspfCtrInBytes | read-only | mandatory | Indicates the total number of bytes in the OSFP packets that have been received, device-wide, during nwIpOspfCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.9 | ScalarnwIpOspfCtrOutBytes | read-only | mandatory | Indicates the total number of bytes in the OSPF packets that have been transmitted, device-wide, during nwIpOspfCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.10 | ScalarnwIpOspfCtrFilteredBytes | read-only | mandatory | Indicates the total number of bytes in the OSPF packets that have been administratively filtered, device-wide, during nwIpOspfCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.1.2.11 | ScalarnwIpOspfCtrDiscardBytes | read-only | mandatory | Indicates the total number of bytes in the OSPF packets that have been discarded, during nwIpOspfCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2 | NodenwIpOspfInterfaces | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1 | NodenwIpOspfIfConfig | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1 | TablenwIpOspfIfTable | not-accessible | mandatory | This table contains the OSPF configuration information for each IP router port |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1 | RownwIpOspfIfEntry | not-accessible | mandatory | Each entry specifies the OSPF configuration information for the IP router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1.1 | ColumnnwIpOspfIfIndex | read-only | mandatory | This is the primary index into the OSPF interface table. This number corresponds to the index into the MIB-2 Interface Table which describes the router port fo… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1.2 | ColumnnwIpOspfIfAdminStatus | read-write | mandatory | Sets the administrative state of OSPF on the IP router port for which the entry exists. enabled(3) causes OSPF to become active on the router port. disabled(2)… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1.3 | ColumnnwIpOspfIfOperStatus | read-only | mandatory | Sets the administrative state of OSPF on the IP router port for which the entry exists. enabled(3) causes OSPF to become active on the router port. disabled(2)… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1.4 | ColumnnwIpOspfIfOperationalTime | read-only | mandatory | Indicates the elapsed time, in hundredths of a second, that nwIpOspfIfAdminStatus has been in its current state. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1.5 | ColumnnwIpOspfIfVersion | read-write | mandatory | Indicates the OSPF protocol revision level supported on the router port. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1.6 | ColumnnwIpOspfIfSnooping | read-write | mandatory | Controls the operation of OSPF Snooping on the IP router port for which the entry exists.OSPF Snooping is operating OSPF in passive mode, so it receives route … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1.7 | ColumnnwIpOspfIfType | read-only | mandatory | Specifies whether the attached network segment does or does not support broadcast media access. bma (2) indicates that route advertisements can be sent as broa… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1.8 | ColumnnwIpOspfIfAclIdentifier | read-write | mandatory | Specifies the Access Control List ID of the access control list applied to OSPF traffic on the IP router port for which the entry exists. A value of 0 indicate… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.1.1.1.9 | ColumnnwIpOspfIfAclStatus | read-write | mandatory | Controls the operation of the access list configured for OSPF traffic on the IP router port for which the entry exists. enabled(3) causes the access list to be… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2 | NodenwIpOspfIfCounters | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1 | TablenwIpOspfIfCtrTable | not-accessible | mandatory | This table contains the OSPF packet and byte counter for each configured OSPF router port. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1 | RownwIpOspfIfCtrEntry | not-accessible | mandatory | Each entry specifies the OSPF packet and byte counter for for the router for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.1 | ColumnnwIpOspfIfCtrIfIndex | read-only | mandatory | This is the primary index into the OSPF interface counter table. This number corresponds to the index into the MIB-2 Interface Table which describes the router… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.2 | ColumnnwIpOspfIfCtrAdminStatus | read-write | mandatory | Sets the administrative state of the OSPF packet and byte counters on the IP router port for which the entry exists. enabled(3) causes these counters to become… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.3 | ColumnnwIpOspfIfCtrReset | read-write | mandatory | Resets the OSPF packet and byte counters on the router port for which the entry exists. reset (2) resets the interface-specific counters to 0 and nwIpOspfIfCtr… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.4 | ColumnnwIpOspfIfCtrOperationalTime | read-only | mandatory | Indicates the amount of time (# of time ticks) that the interface-specific OSPF packet and byte counters have been active on the router port for which the entr… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.5 | ColumnnwIpOspfIfCtrInPkts | read-only | mandatory | Indicates the total number of OSPF packets that have been received, on the router port for which the entry exists, during nwIpOspfIfCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.6 | ColumnnwIpOspfIfCtrOutPkts | read-only | mandatory | Indicates the total number of OSPF packets that have been transmitted, on the router port for which the entry exists, during nwIpOspfIfCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.7 | ColumnnwIpOspfIfCtrFilteredPkts | read-only | mandatory | Indicates the total number of OSPF packets that have been administratively filtered, on the router port for which the entry exists, during nwIpOspfIfCtrOperati… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.8 | ColumnnwIpOspfIfCtrDiscardPkts | read-only | mandatory | Indicates the total number of OSPF packets that have been discarded, on the router port for which the entry exists, during nwIpOspfIfCtrOperationalTime. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.9 | ColumnnwIpOspfIfCtrInBytes | read-only | mandatory | Indicates the total number of bytes in the OSPF packets that have been received, on the router port for which the entry exists, during nwIpOspfIfCtrOperational… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.10 | ColumnnwIpOspfIfCtrOutBytes | read-only | mandatory | Indicates the total number of bytes in the OSPF packets that have been transmitted, on the router port for which the entry exists, during nwIpOspfIfCtrOperatio… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.11 | ColumnnwIpOspfIfCtrFilteredBytes | read-only | mandatory | Indicates the total number of bytes in the OSPF packets that have been administratively filtered, on the router port for which the entry exists, during nwIpOsp… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.2.2.1.1.12 | ColumnnwIpOspfIfCtrDiscardBytes | read-only | mandatory | Indicates the total number of bytes in the OSPF packets that have been discarded, on the router port for which the entry exists, during nwIpOspfIfCtrOperationa… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.3 | NodenwIpOspfDatabase | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.4.2.1.4 | NodenwIpOspfFilters | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5 | NodenwIpFib | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.1 | NodenwIpFibSystem | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.1.1 | ScalarnwIpRipRoutePriority | read-write | mandatory | Specifies the route priority assigned to routes learned by the RIP routing protocol. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.1.2 | ScalarnwIpOSPFRoutePriority | read-write | mandatory | Specifies the route priority assigned to routes learned by the OSPF routing protocol. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.1.3 | ScalarnwIpStaticRoutePriority | read-write | mandatory | Specifies the route priority assigned to routes learned by statically configured routes.. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2 | NodenwIpOspfFib | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.1 | NodenwIpOspfFibControl | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.1.1 | ScalarnwIpOspfForward | read-only | mandatory | The total number of valid Cabletron IP OSPF FIB entries to include static, dynamic, RIP and BGP4 type routes. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.1.2 | ScalarnwIpOspfLeakAllStaticRoutes | read-write | mandatory | Add all static routes in the IP FIB to the Cabletron IP OSPF FIB for advertisement in OSPF routing protocol announcements. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.1.3 | ScalarnwIpOspfLeakAllRipRoutes | read-write | mandatory | Add all RIP routes in the IP FIB to the Cabletron IP OSPF FIB for advertisement in OSPF routing protocol announcements. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.1.4 | ScalarnwIpOspfLeakAllBgp4Routes | read-write | mandatory | Add all BGP4 routes in the IP FIB to the Cabletron IP OSPF FIB for advertisement in OSPF routing protocol announcements. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2 | NodenwIpOspfFibEntries | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.1 | TablenwIpOspfStaticTable | not-accessible | mandatory | A table of statically configured entries in the Cabletron IP OSPF FIB. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.1.1 | RownwIpOspfStaticEntry | not-accessible | mandatory | A list of information for each static entry in the Cabletron IP OSPF FIB. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.1.1.1 | ColumnnwIpOspfStaticDest | read-only | mandatory | The network Address of a static route leaked from the IP FIB into the Cabletron IP OSPF FIB. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.1.1.2 | ColumnnwIpOspfStaticForwardMask | read-only | mandatory | The network mask of a static route leaked from the IP FIB into the Cabletron IP OSPF FIB. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.1.1.3 | ColumnnwIpOspfStaticNextHop | read-only | mandatory | The next hop address of a static route leaked from the IP FIB into the Cabletron IP OSPF FIB. A value of 0.0.0.0 indicates that packets for the external destin… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.1.1.4 | ColumnnwIpOspfStaticMetric | read-write | mandatory | The Cabletron IP OSPF advertised cost of reaching the leaked static route. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.1.1.5 | ColumnnwIpOspfStaticMetricType | read-write | mandatory | The Cabletron IP OSPF metric type to be advertised using OSPF: Autonomous System External type 1 (1) or Autonomous System External type 2 (2). |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.1.1.6 | ColumnnwIpOspfStaticStatus | read-write | mandatory | By setting this OID to inactive for a particular static route, the static route will be added to the IP OSPF FIB but not advertised. Setting this OID to active… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.2 | NodenwIpOspfDynamicTable | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.3 | NodenwIpOspfRipTable | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.5.2.2.4 | NodenwIpOspfBgp4Table | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6 | NodenwIpEndSystems | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.1 | NodenwIpHostsSystem | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.1.1 | ScalarnwIpHostsTimeToLive | read-only | mandatory | Indicates the amount of time (number of minutes) that an entry can remain in the ARP cache. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.1.2 | ScalarnwIpHostsRetryCount | read-only | mandatory | Indicates the maximum number of times IP Routing Services will retry each attempt to resolve a host address. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2 | NodenwIpHostsInterfaces | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1 | TablenwIpHostCtlTable | not-accessible | mandatory | This table contains the control information for maintaining a cache of IP host addresses on each router port. Note that the of actual entries are maintained by… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1 | RownwIpHostCtlEntry | not-accessible | mandatory | Each entry contains the control information for maintaining the cache on each router port. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.1 | ColumnnwIpHostCtlIfIndex | read-only | mandatory | Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.2 | ColumnnwIpHostCtlAdminStatus | read-write | mandatory | This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the C… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.3 | ColumnnwIpHostCtlOperStatus | read-only | mandatory | Indicates the current operating condition of the IP Host Address cache on the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.4 | ColumnnwIpHostCtlOperationalTime | read-only | mandatory | Indicates the elapsed time, in hundredths of a second, that nwIpHostCtlOperStatus has been in the current state. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.5 | ColumnnwIpHostCtlProtocol | read-write | mandatory | Controls the operation of the ARP protocol on the router port for which the entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.6 | ColumnnwIpHostCtlSnooping | read-write | mandatory | Controls ARP Snooping on the router port for which the entry exists. Given the ARP protocol is enabled, nwIpHostCtlProtocol=3, setting nwIpHostCtlIfSnooping to… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.7 | ColumnnwIpHostCtlProxy | read-write | mandatory | Controls the operations of Proxy ARP on the router port for which the entry exists. Given the ARP protocol is enabled, nwIpHostCtlProtocol=3, setting nwIpHostC… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.8 | ColumnnwIpHostCtlCacheMax | read-write | mandatory | Indicates the maximum number of entry slots the cache can consist of. nwIpHostCtlCacheMax cannot be set to less than 16. Setting this value does not allocate a… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.9 | ColumnnwIpHostCtlCacheSize | read-only | mandatory | Indicates the current number of entry slots in the cache. The cache automatically resizes to accommodate all entries up to the maximum number of entries set by… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.10 | ColumnnwIpHostCtlNumStatics | read-only | mandatory | Indicates the total number of static entries in the cache on the router port for which the entry exists. Static entries remain in the cache until they are admi… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.11 | ColumnnwIpHostCtlNumDynamics | read-only | mandatory | Indicates the number of dynamic entries in the cache on the router port for which the entry exists. Dynamic entries area added and aged out by the ARP protocol. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.12 | ColumnnwIpHostCtlCacheHits | read-only | mandatory | Indicates the number of times an entry in the cache has been used to successfully provide the physical address required to forward an IP packet on the router p… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.2.1.1.13 | ColumnnwIpHostCtlCacheMisses | read-only | mandatory | Indicates the number of times the physical address required to forward an IP packet has not been found in the cache on the router port for which the entry exis… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3 | NodenwIpHostsToMedia | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3.1 | TablenwIpHostMapTable | not-accessible | mandatory | The Ip Address translation table used for mapping an IP address to physical address, framing, port and circuit identifier, if applicable. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3.1.1 | RownwIpHostMapEntry | not-accessible | mandatory | Each entry contains one IpAddress to 'physical' address equivalence, including a circuit identifier if applicable. Also provided is the framing and port number… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3.1.1.1 | ColumnnwIpHostMapIfIndex | read-only | mandatory | This is the primary (major) index into the HostMap table. This number corresponds to the index into the MIB-2 Interfaces Group which describes the IP router po… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3.1.1.2 | ColumnnwIpHostMapIpAddr | read-only | mandatory | The IpAddress corresponding to the media-dependent 'physical' address and circuit identifier (if applic). |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3.1.1.3 | ColumnnwIpHostMapPhysAddr | read-write | mandatory | The media-dependent 'physical' address. The value of this object is 0 for entries indicating native-wan(8) framing. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3.1.1.4 | ColumnnwIpHostMapType | read-write | mandatory | Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the nwIpHostMapTable. That is, it effectively dissasociat… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3.1.1.5 | ColumnnwIpHostMapCircuitID | read-write | mandatory | The identifier for the virtual circuit present on the interface. On an interface configured for Frame Relay, this number is the DLCI for the IP Address at the … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3.1.1.6 | ColumnnwIpHostMapFraming | read-write | mandatory | Specifies the framing type required to converse with the host for which this entry exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.6.3.1.1.7 | ColumnnwIpHostMapPortNumber | read-only | mandatory | The unique value for the logical port number. It's value ranges between 1 and a maximum value which is dependent on both the number of interfaces in the system… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.7 | NodenwIpAccessControl | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.1 | ScalarnwIpAclValidEntries | read-only | mandatory | Indicates the number of valid entries that exist in the access control list table. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2 | TablenwIpAclTable | not-accessible | mandatory | This table contains the access control list information for IP traffic. This table contains entries, each of which allows packet forwarding between source/dest… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1 | RownwIpAclEntry | not-accessible | mandatory | Each entry contains IP source/destination access information. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.1 | ColumnnwIpAclIdentifier | read-only | mandatory | This is the primary (major) index into the IP access control list table. This value identifies the access control list by a unique identifier arbitrarily assig… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.2 | ColumnnwIpAclSequence | read-only | mandatory | This is the secondary (minor) index into the IP access control list table. This number corresponds to a sequence number used to order multiple entries within t… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.3 | ColumnnwIpAclPermission | read-write | mandatory | Specifies whether access is allowed or denied between the source and destination address pair. Note that source and destination are interchangeable when bi-dir… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.4 | ColumnnwIpAclMatches | read-only | mandatory | Indicates the number of matches on this entry that have resulted in the permit/deny access restriction being applied as part of the forwarding process. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.5 | ColumnnwIpAclDestAddress | read-write | mandatory | Specifies the destination IP address used to compare for matches on the access control list. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.6 | ColumnnwIpAclDestMask | read-write | mandatory | Specifies the mask to be applied to the destination address to determine the portion of the address used to compare for matches on the access control list. Onl… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.7 | ColumnnwIpAclSrcAddress | read-write | mandatory | Specifies the source address used to compare for matches on the access control list. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.8 | ColumnnwIpAclSrcMask | read-write | mandatory | Specifies the mask to be applied to the source address to determine the portion of the address to be used to compare for matches on the access control list. On… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.9 | ColumnnwIpAclProtocol | read-write | mandatory | Specifies the IP protocols checked to compare for matches on the access control list. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.7.2.1.10 | ColumnnwIpAclPortNumber | read-write | mandatory | Specifies the port number used to compare for matches on the access control list. nwIpAclPortNumber only applies if nwIpAclProtocol is equal to 4 or 5, UDP or … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.8 | NodenwIpFilters | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.9 | NodenwIpRedirector | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.9.1 | NodenwIpRedirectorSystem | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.9.1.1 | TablenwIpRedirectTable | not-accessible | mandatory | This table contains an entry for each UDP port configured for UDP broadcast redirection. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.9.1.1.1 | RownwIpRedirectEntry | not-accessible | mandatory | Each entry contains the UDP port number of and IP Address to which UDP packets received as LAN broadcasts, should be redirected. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.9.1.1.1.1 | ColumnnwIpRedirectPort | read-only | mandatory | This is the primary index into the UDP redirector table, identifying the UDP port number of the packets that will be redirected. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.9.1.1.1.2 | ColumnnwIpRedirectAddress | read-write | mandatory | Sets the IP address to which the UDP broadcast packets matching the UDP redirect port value (nwIpRedirectPort) will be forwarded. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.9.1.1.1.3 | ColumnnwIpRedirectType | read-write | mandatory | Set this object to enable or disable the redirector feature for the UDP port specified by nwIpRedirectAddress. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.9.1.1.1.4 | ColumnnwIpRedirectCount | read-only | mandatory | Indicates how many UDP broadcast packets have been redirected, as specified by this entry. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.9.2 | NodenwIpRedirectorInterface | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10 | NodenwIpEvent | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.1 | NodenwIpEventLogConfig | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.1.1 | ScalarnwIpEventAdminStatus | read-write | mandatory | Sets the administrative state of IP event logging. enabled(3) causes the event log to become active. disabled(2) causes the event log to become inactive. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.1.2 | ScalarnwIpEventMaxEntries | read-write | mandatory | Sets the administrative state of IP event logging. Enabled (3) causes the event log to become active. Disabled (2) causes the event log to become inactive. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.1.3 | ScalarnwIpEventTraceAll | read-write | mandatory | Enabled (3) allows logging of all event types on all router ports for all protocols and components. Disabled (2) causes the filter table to specify which event… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.2 | NodenwIpEventLogFilterTable | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.2.1 | TablenwIpEventFilterTable | not-accessible | mandatory | This table contains an entry for each event filter configured for IP Routing Services events. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.2.1.1 | RownwIpEventFilterEntry | not-accessible | mandatory | Each entry describes an event filter which defines a particular type of event to be logged to the event log. The value of nwIpEventProtocol indicates the value… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.2.1.1.1 | ColumnnwIpEventFltrProtocol | read-only | mandatory | Indicates the value of the Cabletron Routing Services MIB nwRtgProtocolInstance or nwComponentRtgInstance which identifies the protocol involved in the event f… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.2.1.1.2 | ColumnnwIpEventFltrIfNum | read-only | mandatory | Specifies the router port involved in the event for which the event filter exists. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.2.1.1.3 | ColumnnwIpEventFltrControl | read-write | mandatory | Set this value to 3 to add the entry to the event filter table. Set this value to 2 to remove the entry from the event filter table. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.2.1.1.4 | ColumnnwIpEventFltrType | read-write | mandatory | This 6 bit mask specifies the types of events to be logged. By default all 6 bits are set to 1, indicating that all types of events are to be logged. Setting a… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.2.1.1.5 | ColumnnwIpEventFltrSeverity | read-write | mandatory | Specifies the level of severity an event must meet in order to be logged. Controls the amount of event logging by ignoring events of a lower priority than spec… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.2.1.1.6 | ColumnnwIpEventFltrAction | read-write | mandatory | Specifies how the events are to be logged. Logging to the `log' stores the events in the event log table (nwIpEventFltrAction). Logging to `trap' sends events … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3 | NodenwIpEventLogTable | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3.1 | TablenwIpEventTable | not-accessible | mandatory | This table contains an entry for each event that has been logged. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3.1.1 | RownwIpEventEntry | not-accessible | mandatory | Each entry contains the information about an event that has been logged to the event table. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3.1.1.1 | ColumnnwIpEventNumber | read-only | mandatory | An ordinal value assigned to the event for which the log entry exists. nwIpEventNumber is assigned so that each event in the event log can be uniquely identifi… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3.1.1.2 | ColumnnwIpEventTime | read-only | mandatory | Indicates the time at which the event was logged to the event log. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3.1.1.3 | ColumnnwIpEventType | read-only | mandatory | Indicates the type of event that was logged. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3.1.1.4 | ColumnnwIpEventSeverity | read-only | mandatory | Indicates the severity that was assigned to the event. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3.1.1.5 | ColumnnwIpEventProtocol | read-only | mandatory | Indicates the value of the Cabletron Routing Services MIB nwRtgProtocolInstance or nwComponentInstance which indentifies the protocol or component that was inv… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3.1.1.6 | ColumnnwIpEventIfNum | read-only | mandatory | Indicates the router port that was involved in the event. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.10.3.1.1.7 | ColumnnwIpEventTextString | read-only | mandatory | Contains the actual text string that was logged. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11 | NodenwIpWorkGroup | |||
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1 | TablenwIpWgDefTable | not-accessible | mandatory | This table has an entry for each workgroup subnet definition. It is indexed by and arbitrary integer indentifier. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1 | RownwIpWgDefEntry | not-accessible | mandatory | Each entry specifies the configuration and status of an individual work group. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1.1 | ColumnnwIpWgDefIdentifier | read-only | mandatory | An index into the definition table, unique to each entry, arbitrarily assigned by the user. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1.2 | ColumnnwIpWgDefHostAddress | read-write | mandatory | The IP address of the IP router host which applies to every interface included in the workgroup. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1.3 | ColumnnwIpWgDefSubnetMask | read-write | mandatory | The subnet mask for the IP address above, thereby defining the subnet which applies to every interface included in the workgroup. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1.4 | ColumnnwIpWgDefSecurity | read-write | mandatory | A security level which applies to this workgroup as a whole. Security applies in conjunction with the range table below, which locks hosts to interfaces and/or… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1.5 | ColumnnwIpWgDefFastPath | read-write | mandatory | Enabled (3) provides a fast path for packets through the router when both source and destination are within this workgroup - done mostly by skipping IP header … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1.6 | ColumnnwIpWgDefRowStatus | read-write | mandatory | This status instance does not support `createAndGo.' A row entry should be created by a set of `createAndWait' which brings the status to `notReady.' The missi… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1.7 | ColumnnwIpWgDefOperStatus | read-only | mandatory | The operational status of this workgroup definition entry. It will be `disabled' if this entry's row status is not active. It will be `subnetConflict' if there… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1.8 | ColumnnwIpWgDefNumActiveIntf | read-only | mandatory | The number of interfaces (ports) in this workgroup which have an operational status nwIpWgIfOperStatus of `OK' in the IP Work Group Interface table below. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.1.1.9 | ColumnnwIpWgDefNumTotalIntf | read-only | mandatory | The number of interfaces (ports) in this workgroup which have an administrative status nwIpWgIfRowStatus of `active' in the IP Work Group Interface table below. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.2 | TablenwIpWgIfTable | not-accessible | mandatory | This table contains an entry for each port in a workgroup. It is indexed by the workgroup identifier and the MIB-II interface indentifier. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.2.1 | RownwIpWgIfEntry | not-accessible | mandatory | Each entry specifies the association of a router port to a defined workgroup. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.2.1.1 | ColumnnwIpWgIfDefIdent | read-only | mandatory | The workgroup identifier. This is the primary index into the IP Work Group Interface Table, matching the index into the Definition Table above. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.2.1.2 | ColumnnwIpWgIfIfIndex | read-only | mandatory | The interface number. This is the secondary index into the IP Work Group Interface Table, matching the primary index into the MIB-2 IfTable which describes the… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.2.1.3 | ColumnnwIpWgIfNumActiveHosts | read-only | mandatory | The number of hosts known to be active on this interface in this workgroup. These hosts are visible in the IP Work Group Host Table below. Hosts age out and be… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.2.1.4 | ColumnnwIpWgIfNumKnownHosts | read-only | mandatory | The number of hosts seen on this interface in this workgroup since this interface entry was last activated. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.2.1.5 | ColumnnwIpWgIfRowStatus | read-write | mandatory | This status instance supports `createAndGo' semantics to create an active entry. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.2.1.6 | ColumnnwIpWgIfOperStatus | read-only | mandatory | The operational status of this interface (port) entry. It will be `disabled' if this entry's row status is not active. It will be `workgroupInvalid' if either … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.3 | TablenwIpWgRngTable | not-accessible | mandatory | This table locks ranges of IP hosts (addresses) to ports. Entries in this table represent explicit permissions. The host(s) represented by a range entry may ex… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.3.1 | RownwIpWgRngEntry | not-accessible | mandatory | Each entry configures a range of host IP addresses to be associated with a given interface ( port ). If the range consists of a single host address the entry m… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.3.1.1 | ColumnnwIpWgRngBegHostAddr | read-only | mandatory | The beginning (lower) IP address of the address range. This is the primary index into the IP Work Group Range Table. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.3.1.2 | ColumnnwIpWgRngEndHostAddr | read-only | mandatory | The ending (higher) IP address of the address range. This is the secondary index of the IP Work Group Range Table. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.3.1.3 | ColumnnwIpWgRngIfIndex | read-only | mandatory | The interface number. This is the tertiary index into the IP Work Group Interface Table, matching the primary index into the MIB-2 IfTable which describes the … |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.3.1.4 | ColumnnwIpWgRngPhysAddr | read-write | mandatory | The physical address of the host with the IP address given in the nwIpWgRngBegHostAddr for this conceptual row entry. Only single host range entry in which nwI… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.3.1.5 | ColumnnwIpWgRngRowStatus | read-write | mandatory | This status instance supports `createAndGo' semantics to create an active entry. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.3.1.6 | ColumnnwIpWgRngOperStatus | read-only | mandatory | The operational status of this range table entry. It will be `disabled' if this entry's row status is not active. It will be `workgroupInvalid' if either there… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.4 | TablenwIpWgHostTable | not-accessible | mandatory | A read only status table for hosts in workgroups. It has the information similar to a net-to-media table. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.4.1 | RownwIpWgHostEntry | not-accessible | mandatory | Each entry shows a workgroup host. Entry is indexed by IP address and interface (port). It gives the workgroup and the physical address found for the host. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.4.1.1 | ColumnnwIpWgHostHostAddr | read-only | mandatory | The host IP address. This is the primary index to the IP Work Group Host Table. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.4.1.2 | ColumnnwIpWgHostIfIndex | read-only | mandatory | The interface (port) number. This is the secondary index to the IP Work Group Host Table, matching the primary index to the MIB-2 IfTable which describes the r… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.4.1.3 | ColumnnwIpWgHostDefIdent | read-only | mandatory | The workgroup identifier. This corresponds to the primary index into the IP Work Group Interface Table. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.4.1.4 | ColumnnwIpWgHostPhysAddr | read-only | mandatory | The physical address of the host with the IP address given in the nwIpWgHostHostAddr for this conceptual row entry. |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.11.4.1.5 | ColumnnwIpWgHostStatus | read-only | mandatory | This status of the host with respect to the workgroup. The host may be `unknown' if ARP has not discovered on which port it resides. The status of `invalid-mul… |
| 1.3.6.1.4.1.52.4.2.2.2.3.1.2.12 | NodenwIpClientServices |