CTRON-ISDN-CONFIGURATION-MIB
66 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter enterprises |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.52 | Nodecabletron | |||
| 1.3.6.1.4.1.52.4 | Nodemibs | |||
| 1.3.6.1.4.1.52.4.1 | Nodectron | |||
| 1.3.6.1.4.1.52.4.1.2 | NodectDataLink | |||
| 1.3.6.1.4.1.52.4.1.2.7 | NodectronWan | |||
| 1.3.6.1.4.1.52.4.1.2.7.4 | NodectISDNconfigMib | |||
| 1.3.6.1.4.1.52.4.1.2.7.4.1 | NodectISDNcontrol | |||
| 1.3.6.1.4.1.52.4.1.2.7.4.1.1 | TableisdnDchTable | not-accessible | mandatory | A list of D channnel interfaces entries. The list consists of a single entry at this time. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.1.1 | RowisdnDchEntry | not-accessible | mandatory | A D channnel interface entry containing objects relating to the particular D channel. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.1 | ColumnisdnDchIndex | read-only | mandatory | A unique index for this D Channel of this ISDN-Controller. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.2 | ColumnisdnDchRateAccess | read-only | mandatory | The Rate Access of this ISDN interface. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.3 | ColumnisdnDchAllowedCh | read-only | mandatory | A bit string with bit 1 signifiying time slot 1. A set bit means that a B channel may be allocated on that time slot. A reset bit means the channel is reserved… |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.4 | ColumnisdnDchChInUse | read-only | mandatory | A bit string with bit 1 signifying time slot 1. A set bit means that a B channel has been allocated on that time slot. A reset bit means the channel is availab… |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.5 | ColumnisdnDchSupportedSwitches | read-only | mandatory | A bit string with each bit position signifying support of a specific switch type as indicated by the list. A set bit means that that switch type is supported. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.6 | ColumnisdnDchSwitchType | read-write | mandatory | Switch type selector as indicated by the list. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.7 | ColumnisdnDchSPID1 | read-write | mandatory | The Service profile identifier for BRI channel 1. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.8 | ColumnisdnDchSPID2 | read-write | mandatory | The Service profile identifier for BRI channel 2. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.9 | ColumnisdnDchDirNum1 | read-write | mandatory | The local directory number for BRI channel 1. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.10 | ColumnisdnDchDirNum2 | read-write | mandatory | The local directory number for BRI channel 2. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.11 | ColumnisdnDchOperStatus | read-only | mandatory | The operational status of the signalling channel. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.2 | TabledialCtlNbrCfgTable | not-accessible | mandatory | The list of neighbors from which the managed device will accept calls or to which it will place them. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.2.1 | RowdialCtlNbrCfgEntry | not-accessible | mandatory | A single Neighbor. This entry is effectively permanent, and contains address information describing the neighbor. The value of dialCtlNbrCfgOriginateAddress mu… |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.2.1.1 | ColumndialCtlNbrCfgId | read-only | mandatory | This object defines a single neighbor. There may be several entries in this table for one neighbor, defining different ways of reaching this neighbor. Thus, th… |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.2.1.2 | ColumndialCtlNbrCfgIndex | read-only | mandatory | The index value which uniquely identifies an entry in this table. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.2.1.3 | ColumndialCtlNbrCfgIfIndex | read-only | mandatory | The ifIndex value of the interface associated with this neighbor. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.2.1.4 | ColumndialCtlNbrCfgOriginateAddress | read-write | mandatory | Call Address at which the neighbor will be called. Think of this as the set of characters following 'ATDT ' or the 'phone number' included in a D channel call … |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.2.1.5 | ColumndialCtlNbrCfgAnswerAddress | read-write | mandatory | Calling Party Number information element, as for example passed in an ISDN SETUP message by a PBX or switch, for incoming calls. This address can be used to id… |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3 | TablermtProfileTable | not-accessible | mandatory | The list of neighbors from which this device will accept calls or to which it will place them. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1 | RowrmtProfileEntry | not-accessible | mandatory | A single Neighbor. This entry is effectively permanent, and contains information describing the neighbor. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.1 | ColumnrmtProfileEntryIndex | read-only | mandatory | The index value which uniquely identifies an entry in this table. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.2 | ColumnrmtProfileEntryName | read-write | mandatory | ASCII name of the neighbor. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.3 | ColumnrmtProfileEntryMakerName | read-write | mandatory | ASCII name of the manufacturer of the neighbor. In other words, it is a name by which to uniquely identify the remote access device to which the profile belong… |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.4 | ColumnrmtProfileEntryAction | read-write | mandatory | Desired action for the neighbor interface |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.5 | ColumnrmtProfileEntryState | read-only | mandatory | Current state of the neighbor interface |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.6 | ColumnrmtProfileEntryMaxNeighbor | read-only | mandatory | The maximum allowable dialCtlNbrCfgIndex. It is the number of instances of the profile. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.7 | ColumnrmtProfileEntryBchInUse | read-only | mandatory | A bit string with bit 1 signifiying B channel 1. A set bit means that this channel was assigned for current or last call. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.8 | ColumnrmtProfileEntryLinkHead | read-only | mandatory | A zero value signifies it is a primary profile. Otherwise, it is an instance profile and the value identifies the primary profile from which it was spawned. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.9 | ColumnrmtProfileEntryNextLink | read-only | mandatory | A non-zero value identifies an instance profile. Whereas, a zero value either means it is a primary profile or the last instance of a primary profile. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.10 | ColumnrmtProfileEntryMpCapable | read-write | mandatory | MP option selector. Set to a value of one when MP support is desired otherwise set to a value of two. The default setting is disabled. When enabled the attempt… |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.11 | ColumnrmtProfileEntryMpLineUtilization | read-write | mandatory | Used to set the Line Utilization Threshold (LUT) % to compare against the linear weighted percentage to determine when more/less bandwidth is to be added/remov… |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.12 | ColumnrmtProfileEntryMpHistoryTime | read-write | mandatory | Used to set the history time value in seconds for the number of line utilization reading(s)/sample(s) desired to compute the average line utilization. It speci… |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.13 | ColumnrmtProfileEntryMpMoreBWSamples | read-write | mandatory | Used to set the number of consecutive line utilization average computations that must exceed the LUT % value as specified by the rmtProfileEntryMpLineUtilizati… |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.14 | ColumnrmtProfileEntryMpLessBWSamples | read-write | mandatory | Used to set the number of consecutive line utilization average computations that must fall below the LUT % value as specified by the rmtProfileEntryMpLineUtili… |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.15 | ColumnrmtProfileEntryMpMaxCallsAllowed | read-write | mandatory | Used to set the maxium number of channels an ISDN MP capable call is allowed. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.16 | ColumnrmtProfileEntryMpCallsToAdd | read-write | mandatory | Used to set the number of additional channel(s) (call(s)) to increment by whenever the need for more bandwidth is determined. |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.17 | ColumnrmtProfileEntryMpCallsToRemove | read-write | mandatory | Used to set the number of channel(s) (call(s)) to decrement by whenever the need for possible previously added additional bandwidth is determined to no longer … |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.18 | ColumnrmtProfileEntryMpAvgPktSize | read-write | mandatory | Used to set the average packet size by which to determine when its best to split a packet. This is an attempt to minimize the amount of buffering necessary at … |
| 1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.19 | ColumnrmtProfileEntryMpRmtBwCtrl | read-write | mandatory | MP remote bandwidth control selector. Set to a one when bandwidth changes are permitted by either side ie by both parties otherwise set to a value of two. The … |
| 1.3.6.1.4.1.52.4.1.2.7.4.2 | NodecallHistory | |||
| 1.3.6.1.4.1.52.4.1.2.7.4.2.1 | ScalarcallHistoryTableMaxLength | read-only | mandatory | The upper limit on the number of entries that the callHistoryTable may contain. When this table is full, the oldest entry will be deleted and the new one will … |
| 1.3.6.1.4.1.52.4.1.2.7.4.2.2 | TablecallHistoryTable | not-accessible | mandatory | A table containing information about specific calls to a specific destination. |
| 1.3.6.1.4.1.52.4.1.2.7.4.2.2.1 | RowcallHistoryEntry | not-accessible | mandatory | The information regarding a single Connection. |
| 1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.1 | ColumncallHistorySetupTime | read-only | mandatory | The value of system up time when the call associated to this entry was started. This will be useful for an NMS to retrieve all calls after a specific time. Als… |
| 1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.2 | ColumncallHistoryIndex | read-only | mandatory | Index variable to access the CallHistoryEntry objects of the callHistoryTable. |
| 1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.3 | ColumncallHistoryPeerAddress | read-only | mandatory | The number this call is connected to. If the number is not available, then it will have a length of zero. |
| 1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.4 | ColumncallHistoryNeighborId | read-only | mandatory | This is the Id value of the neighbor table entry to which this call was made. If a neighbor table entry for this call does not exist, the value of this object … |
| 1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.5 | ColumncallHistoryLogicalIfIndex | read-only | mandatory | This is the ifIndex value of the logical interface through which this call was made. |
| 1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.6 | ColumncallHistoryDisconnectCause | read-only | mandatory | The encoded network cause value associated with this call. The value of this object will depend on the interface type as well as on the protocol and protocol v… |
| 1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.7 | ColumncallHistoryConnectTime | read-only | mandatory | The value of system up time when the call was connected. |
| 1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.8 | ColumncallHistoryDisconnectTime | read-only | mandatory | The value of system up time when the call was disconnected. |
| 1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.9 | ColumncallHistoryCallOrigin | read-only | mandatory | The call origin. |
| 1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.10 | ColumncallHistoryInfoType | read-only | mandatory | The information type for this call. |
| 1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.11 | ColumncallHistoryTransmitPackets | read-only | mandatory | The number of packets which were transmitted while this call was active. |
| 1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.12 | ColumncallHistoryTransmitBytes | read-only | mandatory | The number of bytes which were transmitted while this call was active. |
| 1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.13 | ColumncallHistoryReceivePackets | read-only | mandatory | The number of packets which were received while this call was active. |
| 1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.14 | ColumncallHistoryReceiveBytes | read-only | mandatory | The number of bytes which were received while this call was active. |