DES-1210-10AXME
1029 objects
No module-level DESCRIPTION found.
Imported Objects
| IF-MIB | InterfaceIndex InterfaceIndexOrZero |
| INET-ADDRESS-MIB | InetAddress |
| Q-BRIDGE-MIB | VlanId |
| SNMP-FRAMEWORK-MIB | SnmpAdminString SnmpEngineID SnmpSecurityLevel |
| SNMPv2-SMI | Counter32 enterprises Integer32 IpAddress MODULE-IDENTITY OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | DisplayString MacAddress RowStatus TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.171 | Nodedlink | |||
| 1.3.6.1.4.1.171.10 | Nodedlink-products | |||
| 1.3.6.1.4.1.171.10.75 | Nodedlink-DES1210SeriesProd | |||
| 1.3.6.1.4.1.171.10.75.14 | Nodedes-1210-10axme | |||
| 1.3.6.1.4.1.171.10.75.14.1 | NodebridgeGeneral | AST-BRG-GEN-TRAP-VAL. | ||
| 1.3.6.1.4.1.171.10.75.14.1 | NodecompanySystem | |||
| 1.3.6.1.4.1.171.10.75.14.1.1 | ScalarsysSwitchName | read-write | current | System name used for identification of the device. The following characters are allowed to input. 0 ~ 9 / a ~ z / A ~ Z Special character: ( ) �V + - = . |
| 1.3.6.1.4.1.171.10.75.14.1.2 | ScalarsysHardwareVersion | read-only | current | Version number of the Hardware. |
| 1.3.6.1.4.1.171.10.75.14.1.3 | ScalarsysFirmwareVersion | read-only | current | Version number of the Firmware. |
| 1.3.6.1.4.1.171.10.75.14.1.4 | ScalarsysLoginTimeoutInterval | read-write | current | This time interval is used to count the time and logout web interface automatically. |
| 1.3.6.1.4.1.171.10.75.14.1.5 | ScalarsysLocationName | read-write | current | The location name of this node (e.g., `telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string. |
| 1.3.6.1.4.1.171.10.75.14.1.6 | ScalarsysGroupInterval | read-write | current | Group Interval is used to send D-link Discover packet to D-link SmartConsole Utility frequency. The timer in units of seconds. Set value 0 to disable group Int… |
| 1.3.6.1.4.1.171.10.75.14.1.8 | ScalarsysSafeGuardEnable | read-write | current | This object is used to set Safeguard Enable\Disable. |
| 1.3.6.1.4.1.171.10.75.14.1.9 | ScalarsysRestart | read-write | current | This object allows the user to restart the Switch (i.e)the entire switch will operationally go down and start again. Setting a value of 'true' causes the switc… |
| 1.3.6.1.4.1.171.10.75.14.1.10 | ScalarsysSave | read-write | current | This object is used to save Configuration. |
| 1.3.6.1.4.1.171.10.75.14.1.13 | TablesysPortCtrlTable | not-accessible | current | A table to control the port specific parameters of the device like speed, duplex mode, etc. |
| 1.3.6.1.4.1.171.10.75.14.1.13.1 | RowsysPortCtrlEntry | not-accessible | current | An entry appears in this table for each interface in the system. Index to the table is the interface index of the port. |
| 1.3.6.1.4.1.171.10.75.14.1.13.1.1 | ColumnsysPortCtrlIndex | read-only | current | Interface index of the port for the configuration in this entry applies. |
| 1.3.6.1.4.1.171.10.75.14.1.13.1.2 | ColumnsysPortCtrlMediumType | read-only | current | This object indicates the port type: fiber 1G/100M or copper. |
| 1.3.6.1.4.1.171.10.75.14.1.13.1.3 | ColumnsysPortCtrlSpeed | read-write | current | Configures interface speed. |
| 1.3.6.1.4.1.171.10.75.14.1.13.1.4 | ColumnsysPortCtrlOperStatus | read-only | current | The port's operating speed state. |
| 1.3.6.1.4.1.171.10.75.14.1.13.1.5 | ColumnsysPortCtrlMDI | read-write | current | Configures interface auto/mdi/mdix mode. The default setting is Auto. |
| 1.3.6.1.4.1.171.10.75.14.1.13.1.6 | ColumnsysPortCtrlFlowControl | read-write | current | Enables / disables flow control for the interface. |
| 1.3.6.1.4.1.171.10.75.14.1.13.1.7 | ColumnsysPortCtrlFlowControlOper | read-only | current | The link parner negotiate port's operating flow control state. |
| 1.3.6.1.4.1.171.10.75.14.1.13.1.8 | ColumnsysPortCtrlType | read-only | current | The port's media type. |
| 1.3.6.1.4.1.171.10.75.14.1.14 | TablesysPortDescriptionTable | not-accessible | current | The port description table. |
| 1.3.6.1.4.1.171.10.75.14.1.14.1 | RowsysPortDescriptionEntry | not-accessible | current | The port description entry. |
| 1.3.6.1.4.1.171.10.75.14.1.14.1.1 | ColumnsysPortDescIndex | read-only | current | This object indicates the port index. |
| 1.3.6.1.4.1.171.10.75.14.1.14.1.2 | ColumnsysPortDescMediumType | read-only | current | This object indicates the port type: fiber 1G/100M or copper. |
| 1.3.6.1.4.1.171.10.75.14.1.14.1.3 | ColumnsysPortDescString | read-write | current | This object indicates the port description. |
| 1.3.6.1.4.1.171.10.75.14.1.15 | TablesysPortErrTable | not-accessible | current | The port error table. |
| 1.3.6.1.4.1.171.10.75.14.1.15.1 | RowsysPortErrEntry | not-accessible | current | A list of information for the err port of the device. |
| 1.3.6.1.4.1.171.10.75.14.1.15.1.1 | ColumnsysPortErrPortIndex | read-only | current | This object indicates the module's port number.(1..Max port number in the module) |
| 1.3.6.1.4.1.171.10.75.14.1.15.1.2 | ColumnsysPortErrPortState | read-only | current | This object decides whether the port state is enabled or disabled. |
| 1.3.6.1.4.1.171.10.75.14.1.15.1.3 | ColumnsysPortErrPortStatus | read-only | current | This object decides whether the PortStatus is err-disabled. |
| 1.3.6.1.4.1.171.10.75.14.1.15.1.4 | ColumnsysPortErrPortReason | read-only | current | This object decides whether the PortStatus is LBD. |
| 1.3.6.1.4.1.171.10.75.14.1.16 | ScalarsysDhcpAutoConfiguration | read-write | current | This object indicates auto config is enabled or disabled. |
| 1.3.6.1.4.1.171.10.75.14.1.17 | ScalarsysWebState | read-write | current | This object is for Enabled(1) or Disabled(2) Web state in the system. |
| 1.3.6.1.4.1.171.10.75.14.1.18 | ScalarsysWebPortNumber | read-write | current | Web Server Port Number. |
| 1.3.6.1.4.1.171.10.75.14.1.19 | ScalarsysARPAgingTime | read-write | current | This object is for ARP aging time. |
| 1.3.6.1.4.1.171.10.75.14.1.20 | ScalarsysMACAgingTime | read-write | current | This object is for MAC aging time. |
| 1.3.6.1.4.1.171.10.75.14.1.23 | ScalartelnetsettingManagementOnOff | read-write | current | Enable/Disable management Telnetsetting mechanism. |
| 1.3.6.1.4.1.171.10.75.14.1.24 | ScalartelnetUDPPort | read-write | current | The value is for setting telnet's UDP Port. |
| 1.3.6.1.4.1.171.10.75.14.1.25 | ScalarautoRefreshConfiguration | read-write | current | To set the WEB panel auto refresh timer. |
| 1.3.6.1.4.1.171.10.75.14.2 | NodebridgeError | AST-BRG-ERR-TRAP-VAL. | ||
| 1.3.6.1.4.1.171.10.75.14.2 | NodecompanyIpifGroup | |||
| 1.3.6.1.4.1.171.10.75.14.2.1 | ScalarsysIpAddrCfgMode | read-write | current | Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'sysDefault… |
| 1.3.6.1.4.1.171.10.75.14.2.2 | ScalarsysIpAddr | read-write | current | Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored. |
| 1.3.6.1.4.1.171.10.75.14.2.3 | ScalarsysIpSubnetMask | read-write | current | IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored. |
| 1.3.6.1.4.1.171.10.75.14.2.4 | ScalarsysGateway | read-write | current | Gateway |
| 1.3.6.1.4.1.171.10.75.14.2.5 | ScalardhcpOption12Status | read-write | current | Status of DHCP Option12 |
| 1.3.6.1.4.1.171.10.75.14.2.6 | ScalardhcpOption12HostName | read-write | current | Host name in DHCP option 12 |
| 1.3.6.1.4.1.171.10.75.14.3 | NodecompanyTftpGroup | |||
| 1.3.6.1.4.1.171.10.75.14.3 | NodestpNewRoot | AST-NEW-ROOT-TRAP-VAL. | ||
| 1.3.6.1.4.1.171.10.75.14.3.1 | ScalartftpFwServerIpAddress | read-write | current | The TFTP server's IP address is used to upload or download firmware. |
| 1.3.6.1.4.1.171.10.75.14.3.2 | ScalartftpFwImageFileName | read-write | current | Configure firmware filename to download. |
| 1.3.6.1.4.1.171.10.75.14.3.3 | ScalartftpFwTftpOperation | read-write | current | The tftp operates to perform downloading the firmware image to the unit. This object is used in conjunction with configBootTftpServerIp and configBootImageFile… |
| 1.3.6.1.4.1.171.10.75.14.3.4 | ScalartftpFwTftpOperationStatus | read-only | current | The tftp operation status represent firmware backup or upgrade status. |
| 1.3.6.1.4.1.171.10.75.14.3.5 | ScalartftpCfgServerIpAddress | read-write | current | The TFTP server's IP address is used to upload or download configuration file. |
| 1.3.6.1.4.1.171.10.75.14.3.6 | ScalartftpConfigFileName | read-write | current | The configuration filename is used to store or retrieve config from the tftp server. |
| 1.3.6.1.4.1.171.10.75.14.3.7 | ScalartftpConfigTftpOperation | read-write | current | The tftp operates to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object … |
| 1.3.6.1.4.1.171.10.75.14.3.8 | ScalartftpConfigTftpOperationStatus | read-only | current | The tftp operation status represent configuration file backup or restore status. |
| 1.3.6.1.4.1.171.10.75.14.4 | NodecompanyMiscGroup | |||
| 1.3.6.1.4.1.171.10.75.14.4 | NodetopologyChange | AST-TOPOLOGY-CHG-TRAP-VAL. | ||
| 1.3.6.1.4.1.171.10.75.14.4.2 | ScalarmiscReset | read-write | current | Physically resets the unit - use with care. A (1) resets the unit, a (2) does nothing. |
| 1.3.6.1.4.1.171.10.75.14.4.3 | ScalarmiscStatisticsReset | read-write | current | Resets the units statistics. A (1) resets the statistics count, a (2) does nothing. |
| 1.3.6.1.4.1.171.10.75.14.5 | NodecompanySNMPV3 | |||
| 1.3.6.1.4.1.171.10.75.14.5 | NodeprotocolMigration | AST-PROTOCOL-MIGRATION-TRAP-VAL. | ||
| 1.3.6.1.4.1.171.10.75.14.5.1 | ScalarsnmpGlobalState | read-write | current | This object is for enabling or disabling SNMP Community function. |
| 1.3.6.1.4.1.171.10.75.14.5.2 | NodesnmpV3User | |||
| 1.3.6.1.4.1.171.10.75.14.5.2.1 | TablesnmpV3UserTable | not-accessible | current | |
| 1.3.6.1.4.1.171.10.75.14.5.2.1.1 | RowsnmpV3UserEntry | not-accessible | current | |
| 1.3.6.1.4.1.171.10.75.14.5.2.1.1.1 | ColumnsnmpV3UserName | read-only | current | A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID. |
| 1.3.6.1.4.1.171.10.75.14.5.2.1.1.2 | ColumnsnmpV3UserVersion | read-only | current | A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID. |
| 1.3.6.1.4.1.171.10.75.14.5.2.1.1.3 | ColumnsnmpV3UserGroupName | read-create | current | The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAcces… |
| 1.3.6.1.4.1.171.10.75.14.5.2.1.1.4 | ColumnsnmpV3UserAuthProtocol | read-create | current | An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be authenticated, and if so, the type … |
| 1.3.6.1.4.1.171.10.75.14.5.2.1.1.5 | ColumnsnmpV3UserAuthProtocolPassword | read-create | current | |
| 1.3.6.1.4.1.171.10.75.14.5.2.1.1.6 | ColumnsnmpV3UserPrivProtocol | read-create | current | An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be protected from disclosure, and if s… |
| 1.3.6.1.4.1.171.10.75.14.5.2.1.1.7 | ColumnsnmpV3UserPrivProtocolPassword | read-create | current | |
| 1.3.6.1.4.1.171.10.75.14.5.2.1.1.8 | ColumnsnmpV3UserStatus | read-create | current | The status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the us… |
| 1.3.6.1.4.1.171.10.75.14.5.3 | NodesnmpV3Group | |||
| 1.3.6.1.4.1.171.10.75.14.5.3.1 | TablesnmpV3GroupTable | not-accessible | current | |
| 1.3.6.1.4.1.171.10.75.14.5.3.1.1 | RowsnmpV3GroupEntry | not-accessible | current | |
| 1.3.6.1.4.1.171.10.75.14.5.3.1.1.1 | ColumnsnmpV3GroupName | read-only | current | The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAcces… |
| 1.3.6.1.4.1.171.10.75.14.5.3.1.1.2 | ColumnsnmpV3GroupSecurityModel | read-only | current | In order to gain the access rights allowed by this conceptual row, this securityModel must be in use. |
| 1.3.6.1.4.1.171.10.75.14.5.3.1.1.3 | ColumnsnmpV3GroupSecurityLevel | read-only | current | The minimum level of security required in order to gain the access rights allowed by this conceptual row. A securityLevel of noAuthNoPriv is less than authNoPr… |
| 1.3.6.1.4.1.171.10.75.14.5.3.1.1.4 | ColumnsnmpV3GroupReadViewName | read-create | current | The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes read access. The identified MIB vie… |
| 1.3.6.1.4.1.171.10.75.14.5.3.1.1.5 | ColumnsnmpV3GroupWriteViewName | read-create | current | The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes write access. The identified MIB vi… |
| 1.3.6.1.4.1.171.10.75.14.5.3.1.1.6 | ColumnsnmpV3GroupNotifyViewName | read-create | current | The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes access for notifications. The ident… |
| 1.3.6.1.4.1.171.10.75.14.5.3.1.1.7 | ColumnsnmpV3GroupStatus | read-create | current | The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row … |
| 1.3.6.1.4.1.171.10.75.14.5.4 | NodesnmpV3ViewTree | |||
| 1.3.6.1.4.1.171.10.75.14.5.4.1 | TablesnmpV3ViewTreeTable | not-accessible | current | |
| 1.3.6.1.4.1.171.10.75.14.5.4.1.1 | RowsnmpV3ViewTreeEntry | not-accessible | current | |
| 1.3.6.1.4.1.171.10.75.14.5.4.1.1.1 | ColumnsnmpV3viewTreeName | read-only | current | The human readable name for a family of view subtrees. |
| 1.3.6.1.4.1.171.10.75.14.5.4.1.1.2 | ColumnsnmpV3viewTreeSubtree | read-only | current | The MIB subtree which when combined with the corresponding instance of vacmViewTreeFamilyMask defines a family of view subtrees. |
| 1.3.6.1.4.1.171.10.75.14.5.4.1.1.3 | ColumnsnmpV3viewTreeMask | read-create | current | The bit mask which, in combination with the corresponding instance of vacmViewTreeFamilySubtree, defines a family of view subtrees. Each bit of this bit mask c… |
| 1.3.6.1.4.1.171.10.75.14.5.4.1.1.4 | ColumnsnmpV3viewTreeType | read-create | current | Indicates whether the corresponding instances of vacmViewTreeFamilySubtree and vacmViewTreeFamilyMask define a family of view subtrees which is included in or … |
| 1.3.6.1.4.1.171.10.75.14.5.4.1.1.5 | ColumnsnmpV3viewTreeStatus | read-create | current | The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row … |
| 1.3.6.1.4.1.171.10.75.14.5.5 | NodesnmpV3Community | |||
| 1.3.6.1.4.1.171.10.75.14.5.5.1 | TablesnmpV3CommunityTable | not-accessible | current | |
| 1.3.6.1.4.1.171.10.75.14.5.5.1.1 | RowsnmpV3CommunityEntry | not-accessible | current | |
| 1.3.6.1.4.1.171.10.75.14.5.5.1.1.1 | ColumnsnmpV3CommunityName | read-only | current | The unique index value of a row in this table. |
| 1.3.6.1.4.1.171.10.75.14.5.5.1.1.2 | ColumnsnmpV3CommunityPolicy | read-create | current | A human readable string representing the corresponding value of snmpCommunityName in a Security Model independent format. |
| 1.3.6.1.4.1.171.10.75.14.5.5.1.1.3 | ColumnsnmpV3CommunityStatus | read-create | current | The status of this conceptual row in the snmpCommunityTable. An entry in this table is not qualified for activation until instances of all corresponding column… |
| 1.3.6.1.4.1.171.10.75.14.5.6 | NodesnmpV3Host | |||
| 1.3.6.1.4.1.171.10.75.14.5.6.1 | TablesnmpV3HostTable | not-accessible | current | |
| 1.3.6.1.4.1.171.10.75.14.5.6.1.1 | RowsnmpV3HostEntry | not-accessible | current | |
| 1.3.6.1.4.1.171.10.75.14.5.6.1.1.1 | ColumnsnmpV3HostAddress | read-only | current | This object contains a transport address. The format of this address depends on the value of the snmpTargetAddrTDomain object. And this object is unique identi… |
| 1.3.6.1.4.1.171.10.75.14.5.6.1.1.2 | ColumnsnmpV3HostCommunityName | read-create | current | The locally arbitrary. |
| 1.3.6.1.4.1.171.10.75.14.5.6.1.1.3 | ColumnsnmpV3HostVersion | read-create | current | The Level of Security to be used when generating SNMP messages using this entry. |
| 1.3.6.1.4.1.171.10.75.14.5.6.1.1.4 | ColumnsnmpV3HostStatus | read-create | current | |
| 1.3.6.1.4.1.171.10.75.14.5.7 | ScalarsnmpV3EngineID | read-write | current | An SNMP engine's administratively-unique identifier. In a simple agent, this value is always that agent's own snmpEngineID value. The value can also take the v… |
| 1.3.6.1.4.1.171.10.75.14.5.8 | NodesnmpV3Trap | |||
| 1.3.6.1.4.1.171.10.75.14.5.8.1 | ScalarsnmpV3TrapSNMPAuthentication | read-write | current | This object is for enabling or disabling SNMP login fail event trap in the system. |
| 1.3.6.1.4.1.171.10.75.14.5.8.2 | ScalarsnmpV3TrapBootup | read-write | current | This object is for enabling or disabling devie Bootup event trap in the system. |
| 1.3.6.1.4.1.171.10.75.14.5.8.3 | ScalarsnmpV3TrapFiberLinkUpDown | read-write | current | This object is for enabling or disabling Fiber link up / link down event trap in the system. |
| 1.3.6.1.4.1.171.10.75.14.5.8.4 | ScalarsnmpV3TrapCopperLinkUpDown | read-write | current | This object is for enabling or disabling Copper link up / link down event trap in the system. |
| 1.3.6.1.4.1.171.10.75.14.5.8.5 | ScalarsnmpV3TrapRSTPStateChange | read-write | current | This object is for enabling or disabling RSTP topology change event trap in the system. |
| 1.3.6.1.4.1.171.10.75.14.5.8.6 | ScalarsnmpV3TrapFirmUpgrade | read-write | current | This object is for enabling or disabling Firmware upgrade suess or fail event trap in the system. |
| 1.3.6.1.4.1.171.10.75.14.6 | NodecompanySTP | |||
| 1.3.6.1.4.1.171.10.75.14.6 | NodeiivalidBpduRxd | AST-INVALID-BPDU-RXD-TRAP-VAL. | ||
| 1.3.6.1.4.1.171.10.75.14.6.1 | NodestpBridgeGlobal | |||
| 1.3.6.1.4.1.171.10.75.14.6.1.1 | ScalarstpModuleStatus | read-write | current | The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. Th… |
| 1.3.6.1.4.1.171.10.75.14.6.1.2 | ScalarstpProtocolVersion | read-write | current | The version of Spanning Tree Protocol the bridge is currently running. The value 'stpCompatible(0)' indicates the Spanning Tree Protocol specified in IEEE 802.… |
| 1.3.6.1.4.1.171.10.75.14.6.1.3 | ScalarstpBridgePriority | read-write | current | The Value of the writable portion of the Bridge Identifier comprising of the first two octets. The values that are set for Bridge Priority must be in steps of … |
| 1.3.6.1.4.1.171.10.75.14.6.1.4 | ScalarstpTxHoldCount | read-write | current | The value used by the Port Transmit state machine to limit the maximum transmission rate. |
| 1.3.6.1.4.1.171.10.75.14.6.1.5 | ScalarstpBridgeMaxAge | read-write | current | The value that all bridges use for MaxAge when this bridge is acting as the root. The granularity of this timer is specified to be 1 second. An agent may retur… |
| 1.3.6.1.4.1.171.10.75.14.6.1.6 | ScalarstpBridgeHelloTime | read-write | current | The amount of time between the transmission of Configuration bridge PDUs by this node in units of hundredths of a second. |
| 1.3.6.1.4.1.171.10.75.14.6.1.7 | ScalarstpBridgeForwardDelay | read-write | current | The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D specifies that the range for this parameter is related… |
| 1.3.6.1.4.1.171.10.75.14.6.1.8 | ScalarstpFowardBPDU | read-write | current | This object is for enabling or disabling forward BPDU. |
| 1.3.6.1.4.1.171.10.75.14.6.1.9 | ScalarstpRootBridge | read-only | current | The bridge identifier of the Root of the common spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the C… |
| 1.3.6.1.4.1.171.10.75.14.6.1.10 | ScalarstpRootCost | read-only | current | The Cost of the path to the CIST Root as seen from this bridge. |
| 1.3.6.1.4.1.171.10.75.14.6.1.11 | ScalarstpMaxAge | read-only | current | The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is … |
| 1.3.6.1.4.1.171.10.75.14.6.1.12 | ScalarstpForwardDelay | read-only | current | This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The… |
| 1.3.6.1.4.1.171.10.75.14.6.1.13 | ScalarstpRootPort | read-only | current | The Port Number of the Port which offers the lowest path cost from this bridge to the CIST Root Bridge. |
| 1.3.6.1.4.1.171.10.75.14.6.2 | TablestpPortTable | not-accessible | current | A table that contains port-specific information for the Spanning Tree Protocol. |
| 1.3.6.1.4.1.171.10.75.14.6.2.1 | RowstpPortEntry | not-accessible | current | A list of information maintained by every port about the Spanning Tree Protocol state for that port. |
| 1.3.6.1.4.1.171.10.75.14.6.2.1.1 | ColumnstpPort | read-only | current | The Port number of the port for which this entry contains spanning tree information. |
| 1.3.6.1.4.1.171.10.75.14.6.2.1.2 | ColumnstpPortStatus | read-write | current | Current state of the Port which can be changed to either Disabled or Enabled for ALL spanning tree instances. Setting this object will override the port's stat… |
| 1.3.6.1.4.1.171.10.75.14.6.2.1.3 | ColumnstpPortPriority | read-write | current | The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting the CistPortPriority value. The values that are … |
| 1.3.6.1.4.1.171.10.75.14.6.2.1.4 | ColumnstpAdminPortPathCost | read-write | current | The contribution of this port to the path cost of paths towards the spanning tree root which include this port. Writing a value of '0' assigns the automaticall… |
| 1.3.6.1.4.1.171.10.75.14.6.2.1.5 | ColumnstpPortPathCost | read-only | current | The contribution of this port to the path cost of paths towards the CIST Root which include this port. |
| 1.3.6.1.4.1.171.10.75.14.6.2.1.6 | ColumnstpPortProtocolMigration | read-write | current | Indicates the Protocol migration state of this Port. When operating in RSTP/MSTP (version >= 2) mode, writing TRUE(1) to this object forces this port to transm… |
| 1.3.6.1.4.1.171.10.75.14.6.2.1.7 | ColumnstpPortEdge | read-write | current | This parameter when TRUE(1) indicates that detection of a port as Edge Port happens automatically and FALSE(2) indicates that this feature is disabled. |
| 1.3.6.1.4.1.171.10.75.14.6.2.1.8 | ColumnstpPortAdminP2P | read-write | current | The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as… |
| 1.3.6.1.4.1.171.10.75.14.6.2.1.9 | ColumnstpPortRestrictedRole | read-write | current | A Boolean value set by management. If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even it has the best spanning tree priorit… |
| 1.3.6.1.4.1.171.10.75.14.6.2.1.10 | ColumnstpPortRestrictedTCN | read-write | current | A Boolean value set by management. If TRUE causes the Port not to propagate received topology change notifications and topology changes to other Ports. This pa… |
| 1.3.6.1.4.1.171.10.75.14.6.2.1.11 | ColumnstpPortHelloTime | read-write | current | The amount of time between the transmission of Configuration bridge PDUs by this node in units of hundredths of a second. |
| 1.3.6.1.4.1.171.10.75.14.6.2.1.12 | ColumnstpPortState | read-only | current | Current state of the Port as defined by the Common spanning tree protocol. |
| 1.3.6.1.4.1.171.10.75.14.6.2.1.13 | ColumnstpPortFowardBPDU | read-write | current | This object is for enabling or disabling forward BPDU. |
| 1.3.6.1.4.1.171.10.75.14.6.3 | NodemstConfigurationIdentification | |||
| 1.3.6.1.4.1.171.10.75.14.6.3.1 | ScalarmstiConfigurationName | read-write | current | The Name for the Region's configuration. By Default Region Name will be equal to the Bridge Mac Address. |
| 1.3.6.1.4.1.171.10.75.14.6.3.2 | ScalarmstiRevisionLevel | read-write | current | Version of the MST Region. |
| 1.3.6.1.4.1.171.10.75.14.6.3.3 | ScalarmstCistVlanMapped | read-only | current | A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 … |
| 1.3.6.1.4.1.171.10.75.14.6.3.4 | ScalarmstCistVlanMapped2k | read-only | current | A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1024 through 2047. The first octet corresponds to VLANs with VlanIndex values 10… |
| 1.3.6.1.4.1.171.10.75.14.6.3.5 | ScalarmstCistVlanMapped3k | read-only | current | A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2048 through 3071. The first octet corresponds to VLANs with VlanIndex values of… |
| 1.3.6.1.4.1.171.10.75.14.6.3.6 | ScalarmstCistVlanMapped4k | read-only | current | A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3072 through 4095. The first octet corresponds to VLANs with VlanIndex values 30… |
| 1.3.6.1.4.1.171.10.75.14.6.3.7 | TablemstVlanMstiMappingTable | not-accessible | current | This table contains one entry for each instance of MSTP. This table maintains context ID as one more index to support Multiple Instances. |
| 1.3.6.1.4.1.171.10.75.14.6.3.7.1 | RowmstVlanMstiMappingEntry | not-accessible | current | A conceptual row containing the status of the MSTP instance. |
| 1.3.6.1.4.1.171.10.75.14.6.3.7.1.1 | ColumnmstInstanceIndex | read-only | current | An arbitrary integer within the range from 1 to the value of Max Instance Number that uniquely identifies an instance. |
| 1.3.6.1.4.1.171.10.75.14.6.3.7.1.2 | ColumnmstSetVlanList | read-write | current | A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 … |
| 1.3.6.1.4.1.171.10.75.14.6.3.7.1.3 | ColumnmstResetVlanList | read-write | current | A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 … |
| 1.3.6.1.4.1.171.10.75.14.6.3.7.1.4 | ColumnmstInstanceVlanMapped | read-write | current | A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 … |
| 1.3.6.1.4.1.171.10.75.14.6.3.7.1.5 | ColumnmstInstanceVlanMapped2k | read-write | current | A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1024 through 2047. The first octet corresponds to VLANs with VlanIndex values 10… |
| 1.3.6.1.4.1.171.10.75.14.6.3.7.1.6 | ColumnmstInstanceVlanMapped3k | read-write | current | A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2048 through 3071. The first octet corresponds to VLANs with VlanIndex values of… |
| 1.3.6.1.4.1.171.10.75.14.6.3.7.1.7 | ColumnmstInstanceVlanMapped4k | read-write | current | A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3072 through 4095. The first octet corresponds to VLANs with VlanIndex values 30… |
| 1.3.6.1.4.1.171.10.75.14.6.4 | NodestpInstance | |||
| 1.3.6.1.4.1.171.10.75.14.6.4.1 | ScalarmstCistBridgePriority | read-write | current | The writable portion of the MSTI Bridge Identifier. comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096. |
| 1.3.6.1.4.1.171.10.75.14.6.4.2 | ScalarmstCistStatus | read-only | current | The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. Th… |
| 1.3.6.1.4.1.171.10.75.14.6.4.3 | TablemstMstiBridgeTable | not-accessible | current | Table containing Bridge Information specific to Spanning Tree Instance. This table maintains context ID as one more index to support Multiple Instances. |
| 1.3.6.1.4.1.171.10.75.14.6.4.3.1 | RowmstMstiBridgeEntry | not-accessible | current | Entry indicating the Bridge Information. |
| 1.3.6.1.4.1.171.10.75.14.6.4.3.1.1 | ColumnmstMstiInstanceIndex | read-only | current | Spanning Tree Instance to which the information belongs. |
| 1.3.6.1.4.1.171.10.75.14.6.4.3.1.2 | ColumnmstMstiBridgePriority | read-write | current | The writable portion of the MSTI Bridge Identifier. comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096. |
| 1.3.6.1.4.1.171.10.75.14.6.4.3.1.3 | ColumnmstMstiStatus | read-only | current | The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. Th… |
| 1.3.6.1.4.1.171.10.75.14.6.5 | NodestpInstancePortTable | |||
| 1.3.6.1.4.1.171.10.75.14.6.5.1 | TablemstCistPortTable | not-accessible | current | This table contains Common Spanning Tree Port Information. |
| 1.3.6.1.4.1.171.10.75.14.6.5.1.1 | RowmstCistPortEntry | not-accessible | current | A list of information maintained by every port for Common Spanning tree. |
| 1.3.6.1.4.1.171.10.75.14.6.5.1.1.1 | ColumnmstCistPort | not-accessible | current | The Port number of the port for which this entry contains spanning tree information. |
| 1.3.6.1.4.1.171.10.75.14.6.5.1.1.2 | ColumnmstCistPortDesignatedBridge | read-only | current | The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment. |
| 1.3.6.1.4.1.171.10.75.14.6.5.1.1.3 | ColumnmstCistPortAdminPathCost | read-write | current | The contribution of this port to the path cost of paths towards the MSTI Root which include this port. |
| 1.3.6.1.4.1.171.10.75.14.6.5.1.1.4 | ColumnmstCistPortPathCost | read-write | current | The contribution of this port to the path cost of paths towards the MSTI Root which include this port. |
| 1.3.6.1.4.1.171.10.75.14.6.5.1.1.5 | ColumnmstCistPortPriority | read-write | current | The four most significant bits of the Port Identifier for a given Spanning Tree instance can be modified independently for each Spanning Tree instance supporte… |
| 1.3.6.1.4.1.171.10.75.14.6.5.1.1.6 | ColumnmstCistForcePortState | read-only | current | Current state of the Port which can be changed to either Disabled or Enabled for the specific spanning tree instance. This object can be set to enabled only if… |
| 1.3.6.1.4.1.171.10.75.14.6.5.1.1.7 | ColumnmstCistCurrentPortRole | read-only | current | Current Port Role of the port for this spanning tree instance. |
| 1.3.6.1.4.1.171.10.75.14.6.5.2 | TablemstMstiPortTable | not-accessible | current | This table contains Spanning Tree Instance Specific Port Information. |
| 1.3.6.1.4.1.171.10.75.14.6.5.2.1 | RowmstMstiPortEntry | not-accessible | current | A list of information maintained by every port for each and every spanning tree instance. |
| 1.3.6.1.4.1.171.10.75.14.6.5.2.1.1 | ColumnmstMstiPort | not-accessible | current | The Port number of the port for which this entry contains spanning tree information. |
| 1.3.6.1.4.1.171.10.75.14.6.5.2.1.2 | ColumnmstMstiPortDesignatedBridge | read-only | current | The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment. |
| 1.3.6.1.4.1.171.10.75.14.6.5.2.1.3 | ColumnmstMstiPortAdminPathCost | read-write | current | The contribution of this port to the path cost of paths towards the MSTI Root which include this port. |
| 1.3.6.1.4.1.171.10.75.14.6.5.2.1.4 | ColumnmstMstiPortPathCost | read-write | current | The contribution of this port to the path cost of paths towards the MSTI Root which include this port. |
| 1.3.6.1.4.1.171.10.75.14.6.5.2.1.5 | ColumnmstMstiPortPriority | read-write | current | The four most significant bits of the Port Identifier for a given Spanning Tree instance can be modified independently for each Spanning Tree instance supporte… |
| 1.3.6.1.4.1.171.10.75.14.6.5.2.1.6 | ColumnmstMstiForcePortState | read-only | current | Current state of the Port which can be changed to either Disabled or Enabled for the specific spanning tree instance. This object can be set to enabled only if… |
| 1.3.6.1.4.1.171.10.75.14.6.5.2.1.7 | ColumnmstMstiCurrentPortRole | read-only | current | Current Port Role of the port for this spanning tree instance. |
| 1.3.6.1.4.1.171.10.75.14.7 | NodecompanyDot1qVlanGroup | |||
| 1.3.6.1.4.1.171.10.75.14.7 | NodenewPortRole | AST-NEW-PORTROLE-TRAP-VAL. | ||
| 1.3.6.1.4.1.171.10.75.14.7.2 | Scalardot1qVlanManagementOnOff | read-write | current | Enable/Disable management VLAN mechanism. |
| 1.3.6.1.4.1.171.10.75.14.7.3 | Scalardot1qVlanManagementid | read-write | current | The management VLAN ID, which will allow to forward packets of that VLAN to CPU. |
| 1.3.6.1.4.1.171.10.75.14.7.5 | Scalardot1qVlanAsyOnOff | read-write | current | Enable/Disable IEEE 802.1Q Asymmetric VLAN |
| 1.3.6.1.4.1.171.10.75.14.7.6 | Tabledot1qVlanTable | not-accessible | current | A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and wi… |
| 1.3.6.1.4.1.171.10.75.14.7.6.1 | Rowdot1qVlanEntry | not-accessible | current | Information for a VLAN configured into the device by (local or network) management. |
| 1.3.6.1.4.1.171.10.75.14.7.6.1.1 | Columndot1qVlanName | read-create | current | An administratively assigned string, which may be used to identify the VLAN. |
| 1.3.6.1.4.1.171.10.75.14.7.6.1.2 | Columndot1qVlanEgressPorts | read-create | current | The set of ports which are permanently assigned to the egress list for this VLAN by management. Changes to a bit in this object affect the per-port per-VLAN Re… |
| 1.3.6.1.4.1.171.10.75.14.7.6.1.3 | Columndot1qVlanForbiddenPorts | read-only | current | The set of ports which are prohibited by management from being included in the egress list for this VLAN. Changes to this object that cause a port to be includ… |
| 1.3.6.1.4.1.171.10.75.14.7.6.1.4 | Columndot1qVlanUntaggedPorts | read-create | current | The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (dot1qVlanIndex = 1) is … |
| 1.3.6.1.4.1.171.10.75.14.7.6.1.5 | Columndot1qVlanAdvertisementStatus | read-create | current | Enable/Disable Advertisement Status of the IEEE 802.1Q VLAN. |
| 1.3.6.1.4.1.171.10.75.14.7.6.1.6 | Columndot1qVlanRowStatus | read-create | current | The status of a row in dot1qVlanTable. By setting this object, new entries can be created in dot1qVlanTable and existing entries can be removed from dot1qVlanT… |
| 1.3.6.1.4.1.171.10.75.14.7.8 | Tabledot1qVlanUngisterMCFilterTable | not-accessible | current | This table contains the list of ports through which a router, in a particular VLAN is reachable. |
| 1.3.6.1.4.1.171.10.75.14.7.8.1 | Rowdot1qVlanUngisterMCFilterEntry | not-accessible | current | A list of multicast filter mode information for each VLAN ID. |
| 1.3.6.1.4.1.171.10.75.14.7.8.1.1 | Columndot1qVlanUngisterMCFilterVlanId | read-only | current | Per Vlan to configure multicast filtering function. |
| 1.3.6.1.4.1.171.10.75.14.7.8.1.2 | Columndot1qVlanUngisterMCFiltermode | read-write | current | Filter unknown multicast frames or normal operation(i.e. forwarding) |
| 1.3.6.1.4.1.171.10.75.14.8 | NodecompanyLA | |||
| 1.3.6.1.4.1.171.10.75.14.8 | NodefirmwareUpgradeSuccess | SNMP-FIRMUPGRADE-SUCC. | ||
| 1.3.6.1.4.1.171.10.75.14.8.1 | NodelaSystem | |||
| 1.3.6.1.4.1.171.10.75.14.8.1.2 | ScalarlaStatus | read-write | current | Sets the Link Aggregation Module administrative status as enabled or disabled. |
| 1.3.6.1.4.1.171.10.75.14.8.1.3 | TablelaPortChannelTable | not-accessible | current | A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. Th… |
| 1.3.6.1.4.1.171.10.75.14.8.1.3.1 | RowlaPortChannelEntry | not-accessible | current | There is one entry in this table for each created port-channel port. |
| 1.3.6.1.4.1.171.10.75.14.8.1.3.1.1 | ColumnlaPortChannelIfIndex | read-only | current | The index of the port-channel(Aggregator's interface index). |
| 1.3.6.1.4.1.171.10.75.14.8.1.3.1.2 | ColumnlaPortChannelMemberList | read-write | current | Member Port list of the port channel. Add the ports as a aggregation member associated of a port-channel. |
| 1.3.6.1.4.1.171.10.75.14.8.1.3.1.3 | ColumnlaPortChannelMode | read-write | current | Current Operating Channel Mode of the port channel Lacp(1) - forcing the port to negotiate with the partner. manual(2) - force the port to enable channeling (M… |
| 1.3.6.1.4.1.171.10.75.14.8.1.3.1.4 | ColumnlaPortChannelMasterPort | read-write | current | The master port of the port-channel. |
| 1.3.6.1.4.1.171.10.75.14.8.1.4 | ScalarlaAlgorithm | read-write | current | Sets the Link Aggregation load balance algorithm. |
| 1.3.6.1.4.1.171.10.75.14.8.2 | NodelaPortControl | |||
| 1.3.6.1.4.1.171.10.75.14.8.2.1 | TablelaPortControlTable | not-accessible | current | A table that contains Link Aggregation Control configuration information about every Aggregation Port associated with this device. A row appears in this table … |
| 1.3.6.1.4.1.171.10.75.14.8.2.1.1 | RowlaPortControlEntry | not-accessible | current | A list of Link Aggregation Control configuration parameters for each Aggregation Port on this device. |
| 1.3.6.1.4.1.171.10.75.14.8.2.1.1.1 | ColumnlaPortControlIndex | read-only | current | The index of the port. |
| 1.3.6.1.4.1.171.10.75.14.8.2.1.1.2 | ColumnlaPortActorPortPriority | read-write | current | The priority value assigned to this Aggregation Port. This 16-bit value is read-write. |
| 1.3.6.1.4.1.171.10.75.14.8.2.1.1.3 | ColumnlaPortActorActivity | read-write | current | This object indicates LACP-Activity to this Aggregation Port. LACP can be configured in one of two modes: active or passive. In active mode it will always send… |
| 1.3.6.1.4.1.171.10.75.14.8.2.1.1.4 | ColumnlaPortActorTimeout | read-write | current | This object indicates LACP-Timeout to this Aggregation Port. short(1) - LACP Timeout 3 seconds. long (2) - LACP Timeout 90 seconds. |
| 1.3.6.1.4.1.171.10.75.14.9 | NodecompanyStaticMAC | |||
| 1.3.6.1.4.1.171.10.75.14.9 | NodefirmwareUpgradeFailure | SNMP-FIRMUPGRADE-FAIL. | ||
| 1.3.6.1.4.1.171.10.75.14.9.1 | ScalarstaticDisableAutoLearn | read-write | current | Set on to disable Auto Learning Excluding Uplink Port and set off to enable Auto Learning. |
| 1.3.6.1.4.1.171.10.75.14.9.2 | ScalarstaticAutoLearningList | read-write | current | The set of the device's member ports that belong to the Static MAC auto learning enable/disable. For example, when Disable Auto Learning is enable, the octet v… |
| 1.3.6.1.4.1.171.10.75.14.9.3 | TablestaticTable | not-accessible | current | A list of the Static MACs |
| 1.3.6.1.4.1.171.10.75.14.9.3.1 | RowstaticEntry | not-accessible | current | A Static MAC entry containing the mac and forwarding port. |
| 1.3.6.1.4.1.171.10.75.14.9.3.1.1 | ColumnstaticVlanID | read-only | current | The VLAN ID of the static MAC entry. |
| 1.3.6.1.4.1.171.10.75.14.9.3.1.2 | ColumnstaticMac | read-only | current | The MAC address associated of the static MAC entry. |
| 1.3.6.1.4.1.171.10.75.14.9.3.1.3 | ColumnstaticPort | read-only | current | The forwarding port of the static MAC entry. |
| 1.3.6.1.4.1.171.10.75.14.9.3.1.4 | ColumnstaticStatus | read-write | current | The status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. The trunk member port ca… |
| 1.3.6.1.4.1.171.10.75.14.10 | NodecompanyIgsGroup | |||
| 1.3.6.1.4.1.171.10.75.14.10 | NodefirmwareIllegalFile | SNMP-FIRMUPGRADE-FAIL2. | ||
| 1.3.6.1.4.1.171.10.75.14.10.1 | NodeigsSystem | |||
| 1.3.6.1.4.1.171.10.75.14.10.1.1 | ScalarigsStatus | read-write | current | Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module starts protocol operations. When set to 'disabled', the IGS module stops… |
| 1.3.6.1.4.1.171.10.75.14.10.1.2 | ScalarigsRouterPortPurgeInterval | read-write | current | This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInter… |
| 1.3.6.1.4.1.171.10.75.14.10.1.3 | ScalarigsHostPortPurgeInterval | read-write | current | This is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received this timer runs for 'PortPurg… |
| 1.3.6.1.4.1.171.10.75.14.10.1.4 | ScalarigsRobustnessValue | read-write | current | When the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attrib… |
| 1.3.6.1.4.1.171.10.75.14.10.1.5 | ScalarigsGrpQueryInterval | read-write | current | The value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there is any intersted receive… |
| 1.3.6.1.4.1.171.10.75.14.10.1.6 | ScalarigsQueryInterval | read-write | current | This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for VLANs. |
| 1.3.6.1.4.1.171.10.75.14.10.1.7 | ScalarigsQueryMaxResponseTime | read-write | current | The maximum query response time advertised in IGMPv2 general queries on this interface. |
| 1.3.6.1.4.1.171.10.75.14.10.3 | NodeigsVlan | |||
| 1.3.6.1.4.1.171.10.75.14.10.3.3 | TableigsVlanRouterTable | not-accessible | current | This table contains the list of ports through which a router, in a particular VLAN is reachable. |
| 1.3.6.1.4.1.171.10.75.14.10.3.3.1 | RowigsVlanRouterEntry | not-accessible | current | Contains the VLAN ID and list of ports on which routers are present in the VLAN. |
| 1.3.6.1.4.1.171.10.75.14.10.3.3.1.1 | ColumnigsVlanRouterVlanId | read-only | current | VLAN ID of the ports through which router is reachable. |
| 1.3.6.1.4.1.171.10.75.14.10.3.3.1.2 | ColumnigsVlanRouterPortList | read-only | current | List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically. |
| 1.3.6.1.4.1.171.10.75.14.10.3.4 | TableigsVlanFilterTable | not-accessible | current | This table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system. |
| 1.3.6.1.4.1.171.10.75.14.10.3.4.1 | RowigsVlanFilterEntry | not-accessible | current | Contains snooping status , version and fast leave configuration for a specific VLAN. |
| 1.3.6.1.4.1.171.10.75.14.10.3.4.1.1 | ColumnigsVlanFilterVlanId | read-only | current | Index of IgsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in IgsVlanFilterEntry is to be done. |
| 1.3.6.1.4.1.171.10.75.14.10.3.4.1.2 | ColumnigsVlanSnoopStatus | read-write | current | This object allows you to enable/disable IGS function on a specific VLAN. |
| 1.3.6.1.4.1.171.10.75.14.10.3.4.1.3 | ColumnigsVlanQuerier | read-only | current | Indicates whether the switch is configured as a querier in the VLAN |
| 1.3.6.1.4.1.171.10.75.14.10.3.4.1.4 | ColumnigsVlanCfgQuerier | read-write | current | The snooping switch can be configured as a querier via this object to send out IGMP general queries when IGMP routers are not present in the VLAN. When set to … |
| 1.3.6.1.4.1.171.10.75.14.10.3.4.1.5 | ColumnigsVlanQueryInterval | read-only | current | This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as … |
| 1.3.6.1.4.1.171.10.75.14.10.3.4.1.6 | ColumnigsVlanRtrPortList | read-write | current | List of ports which are configured statically as router ports |
| 1.3.6.1.4.1.171.10.75.14.10.3.4.1.7 | ColumnigsVlanFbdRtrPortList | read-write | current | List of ports which can be configured statically as forbidden router ports. |
| 1.3.6.1.4.1.171.10.75.14.10.3.4.1.8 | ColumnigsVlanFastLeave | read-write | current | Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for … |
| 1.3.6.1.4.1.171.10.75.14.10.3.5 | TableigsVlanMulticastGroupTable | not-accessible | current | This table contains MAC based multicast forwarding information. |
| 1.3.6.1.4.1.171.10.75.14.10.3.5.1 | RowigsVlanMulticastGroupEntry | not-accessible | current | This table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded. |
| 1.3.6.1.4.1.171.10.75.14.10.3.5.1.1 | ColumnigsVlanMulticastGroupVlanId | read-only | current | VLAN ID pertaining to the Multicast forwarding entry |
| 1.3.6.1.4.1.171.10.75.14.10.3.5.1.2 | ColumnigsVlanMulticastGroupIpAddress | read-only | current | Multicast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format. |
| 1.3.6.1.4.1.171.10.75.14.10.3.5.1.3 | ColumnigsVlanMulticastGroupMacAddress | read-only | current | Multicast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format. |
| 1.3.6.1.4.1.171.10.75.14.10.3.5.1.4 | ColumnigsVlanMulticastGroupPortList | read-only | current | List of ports onto which the multicast data packets destined for this group will be forwarded. |
| 1.3.6.1.4.1.171.10.75.14.10.5 | NodeigsAccessAuth | |||
| 1.3.6.1.4.1.171.10.75.14.10.5.1 | TableigsAccessAuthTable | not-accessible | current | This table is used to manage the IGMP Authentication function of the switch. |
| 1.3.6.1.4.1.171.10.75.14.10.5.1.1 | RowigsAccessAuthEntry | not-accessible | current | Contains management entities for IGMP Authentication function. |
| 1.3.6.1.4.1.171.10.75.14.10.5.1.1.1 | ColumnigsAccessAuthPortIndex | read-only | current | The port index of igsAccessAuthTable which indicates the port to be configured. |
| 1.3.6.1.4.1.171.10.75.14.10.5.1.1.2 | ColumnigsAccessAuthState | read-write | current | This object can be configured to set IGMP Authentication state to enabled/disabled on each port. |
| 1.3.6.1.4.1.171.10.75.14.11 | NodecompanyGVRPGroup | |||
| 1.3.6.1.4.1.171.10.75.14.11 | NodefirmwareTransferError | SNMP-FIRMUPGRADE-FAIL1. | ||
| 1.3.6.1.4.1.171.10.75.14.11.1 | ScalargvrpGVRPGlobalSettingsOnOff | read-write | current | Enable/Disable GVRP mechanism. |
| 1.3.6.1.4.1.171.10.75.14.11.2 | ScalargvrpSettingsJoinTime | read-write | current | The Join Time value assigned to this Join Time field. This 16-bit value is read-write. |
| 1.3.6.1.4.1.171.10.75.14.11.3 | ScalargvrpSettingsLeaveTime | read-write | current | The Leave Time value assigned to this Leave Time field. This 16-bit value is read-write. |
| 1.3.6.1.4.1.171.10.75.14.11.4 | ScalargvrpSettingsLeaveAllTime | read-write | current | The Leave-All Time value assigned to this Leave-All Time field. This 16-bit value is read-write. |
| 1.3.6.1.4.1.171.10.75.14.11.5 | TablegvrpSettingsTable | not-accessible | current | A table containing static configuration information for each GVRP configured into the device by (local or network) management. All entries are permanent and wi… |
| 1.3.6.1.4.1.171.10.75.14.11.5.1 | RowgvrpSettingsEntry | not-accessible | current | Information for a GVRP configured into the device by (local or network) management. |
| 1.3.6.1.4.1.171.10.75.14.11.5.1.1 | ColumngvrpSettingsPortControlIndex | read-only | current | The index of the port. |
| 1.3.6.1.4.1.171.10.75.14.11.5.1.2 | ColumngvrpSettingsPVID | read-write | current | The PVID value assigned to this Aggregation Port. This 16-bit value is read-write. |
| 1.3.6.1.4.1.171.10.75.14.11.5.1.3 | ColumngvrpSettingsGVRPState | read-write | current | Enable/Disable GVRP State to this Aggregation Port. |
| 1.3.6.1.4.1.171.10.75.14.11.5.1.4 | ColumngvrpSettingsIngressChecking | read-write | current | Enable/Disable Ingress Checking mechanism of GVRP to this Aggregation Port. |
| 1.3.6.1.4.1.171.10.75.14.11.5.1.5 | ColumngvrpSettingsAcceptableFrameType | read-write | current | Chose types All Frames/Tagged to this Aggregation Port. |
| 1.3.6.1.4.1.171.10.75.14.12 | NodecompanyQoSGroup | |||
| 1.3.6.1.4.1.171.10.75.14.12 | NodefirmwareChecksumError | SNMP-FIRMUPGRADE-FAIL3. | ||
| 1.3.6.1.4.1.171.10.75.14.12.1 | ScalarcosScheduleMechanism | read-write | current | Queuing mechanism. strictPriority(1) : Strict Priority wrr(2) : Weighted Round Robin Strict-priority scheduling is implemented with a special strict-priority s… |
| 1.3.6.1.4.1.171.10.75.14.12.2 | NodecosOutputSchedule | |||
| 1.3.6.1.4.1.171.10.75.14.12.2.1 | TablecosClassTable | not-accessible | current | A list of cosOutputSchedule. |
| 1.3.6.1.4.1.171.10.75.14.12.2.1.1 | RowcosClassEntry | not-accessible | current | A list of cosOutputClass Weight. |
| 1.3.6.1.4.1.171.10.75.14.12.2.1.1.1 | ColumncosClassIndex | read-only | current | A index of class 0 ~ 3. |
| 1.3.6.1.4.1.171.10.75.14.12.2.1.1.2 | ColumncosWeight | read-write | current | cos weight |
| 1.3.6.1.4.1.171.10.75.14.12.3 | NodeportMapPriority | |||
| 1.3.6.1.4.1.171.10.75.14.12.3.1 | TableportMapPriTable | not-accessible | current | A list of port mapping priority Entries. |
| 1.3.6.1.4.1.171.10.75.14.12.3.1.1 | RowportMapPriEntry | not-accessible | current | A list of 802.1p port mapping priority priorities. |
| 1.3.6.1.4.1.171.10.75.14.12.3.1.1.1 | ColumnportMapPriPortIndex | read-only | current | A port identifier that is in the range of 1 to ifNumber. |
| 1.3.6.1.4.1.171.10.75.14.12.3.1.1.2 | ColumnportMapPriClass | read-write | current | For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization. For… |
| 1.3.6.1.4.1.171.10.75.14.12.4 | NodeqosDefaultUserPri | |||
| 1.3.6.1.4.1.171.10.75.14.12.4.1 | TableqosDefaultUserPriTable | not-accessible | current | A list of 802.1p port default priority Entries. |
| 1.3.6.1.4.1.171.10.75.14.12.4.1.1 | RowqosDefaultUserPriEntry | not-accessible | current | A list of 802.1p port default priority priorities. |
| 1.3.6.1.4.1.171.10.75.14.12.4.1.1.1 | ColumnqosDefaultUserPriPortIndex | read-only | current | A port identifier that is in the range of 1 to ifNumber. |
| 1.3.6.1.4.1.171.10.75.14.12.4.1.1.2 | ColumnqosDefaultPriority | read-write | current | For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization when… |
| 1.3.6.1.4.1.171.10.75.14.12.4.1.1.3 | ColumnqosEffectiveDefaultPriority | read-only | current | For ingress untagged packets, the per port 'Effective Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritiz… |
| 1.3.6.1.4.1.171.10.75.14.12.5 | NodeqosUserPriority | |||
| 1.3.6.1.4.1.171.10.75.14.12.5.1 | TableqosUserPriorityTable | not-accessible | current | A table mapping evaluated User Priority to Traffic Class, for forwarding by the bridge. Traffic class is a number in the range (0..3). |
| 1.3.6.1.4.1.171.10.75.14.12.5.1.1 | RowqosUserPriEntry | not-accessible | current | User Priority to Traffic Class mapping. |
| 1.3.6.1.4.1.171.10.75.14.12.5.1.1.1 | ColumnqosUserPriIndex | read-only | current | For ingress tagged packets, D-Link Smart Switches will refer to these information and prioritize them with 4 different priority queues. If 802.1p is enabled. |
| 1.3.6.1.4.1.171.10.75.14.12.5.1.1.2 | ColumnqosUserPriClass | read-write | current | The User Class the received frame is mapped to. |
| 1.3.6.1.4.1.171.10.75.14.12.6 | NodeqosDiffServ | |||
| 1.3.6.1.4.1.171.10.75.14.12.6.1 | NodeqosDiffServTypeGroup | |||
| 1.3.6.1.4.1.171.10.75.14.12.6.1.1 | ScalarqosDiffServType00 | read-write | current | DiffServ Type 0 : IP ToS value = 0 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.2 | ScalarqosDiffServType01 | read-write | current | DiffServ Type 01 : IP ToS value = 4 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.3 | ScalarqosDiffServType02 | read-write | current | DiffServ Type 02 : IP ToS value = 8 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.4 | ScalarqosDiffServType03 | read-write | current | DiffServ Type 03 : IP ToS value = 12 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.5 | ScalarqosDiffServType04 | read-write | current | DiffServ Type 04 : IP ToS value = 16 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.6 | ScalarqosDiffServType05 | read-write | current | DiffServ Type 05 : IP ToS value = 20 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.7 | ScalarqosDiffServType06 | read-write | current | DiffServ Type 06 : IP ToS value = 24 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.8 | ScalarqosDiffServType07 | read-write | current | DiffServ Type 07 : IP ToS value = 28 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.9 | ScalarqosDiffServType08 | read-write | current | DiffServ Type 08 : IP ToS value = 32 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.10 | ScalarqosDiffServType09 | read-write | current | DiffServ Type 09 : IP ToS value = 36 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.11 | ScalarqosDiffServType10 | read-write | current | DiffServ Type 10 : IP ToS value = 40 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.12 | ScalarqosDiffServType11 | read-write | current | DiffServ Type 11 : IP ToS value = 44 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.13 | ScalarqosDiffServType12 | read-write | current | DiffServ Type 12 : IP ToS value = 48 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.14 | ScalarqosDiffServType13 | read-write | current | DiffServ Type 13 : IP ToS value = 52 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.15 | ScalarqosDiffServType14 | read-write | current | DiffServ Type 14 : IP ToS value = 56 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.16 | ScalarqosDiffServType15 | read-write | current | DiffServ Type 15 : IP ToS value = 60 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.17 | ScalarqosDiffServType16 | read-write | current | DiffServ Type 16 : IP ToS value = 64 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.18 | ScalarqosDiffServType17 | read-write | current | DiffServ Type 17 : IP ToS value = 68 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.19 | ScalarqosDiffServType18 | read-write | current | DiffServ Type 18 : IP ToS value = 72 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.20 | ScalarqosDiffServType19 | read-write | current | DiffServ Type 19 : IP ToS value = 76 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.21 | ScalarqosDiffServType20 | read-write | current | DiffServ Type 20 : IP ToS value = 80 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.22 | ScalarqosDiffServType21 | read-write | current | DiffServ Type 21 : IP ToS value = 84 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.23 | ScalarqosDiffServType22 | read-write | current | DiffServ Type 22 : IP ToS value = 88 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.24 | ScalarqosDiffServType23 | read-write | current | DiffServ Type 23 : IP ToS value = 92 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.25 | ScalarqosDiffServType24 | read-write | current | DiffServ Type 24 : IP ToS value = 96 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.26 | ScalarqosDiffServType25 | read-write | current | DiffServ Type 25 : IP ToS value = 100 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.27 | ScalarqosDiffServType26 | read-write | current | DiffServ Type 26 : IP ToS value = 104 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.28 | ScalarqosDiffServType27 | read-write | current | DiffServ Type 27 : IP ToS value = 108 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.29 | ScalarqosDiffServType28 | read-write | current | DiffServ Type 28 : IP ToS value = 112 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.30 | ScalarqosDiffServType29 | read-write | current | DiffServ Type 29 : IP ToS value = 116 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.31 | ScalarqosDiffServType30 | read-write | current | DiffServ Type 30 : IP ToS value = 120 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.32 | ScalarqosDiffServType31 | read-write | current | DiffServ Type 31 : IP ToS value = 124 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.33 | ScalarqosDiffServType32 | read-write | current | DiffServ Type 32 : IP ToS value = 128 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.34 | ScalarqosDiffServType33 | read-write | current | DiffServ Type 33 : IP ToS value = 132 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.35 | ScalarqosDiffServType34 | read-write | current | DiffServ Type 34 : IP ToS value = 136 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.36 | ScalarqosDiffServType35 | read-write | current | DiffServ Type 35 : IP ToS value = 140 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.37 | ScalarqosDiffServType36 | read-write | current | DiffServ Type 36 : IP ToS value = 144 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.38 | ScalarqosDiffServType37 | read-write | current | DiffServ Type 37 : IP ToS value = 148 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.39 | ScalarqosDiffServType38 | read-write | current | DiffServ Type 38 : IP ToS value = 152 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.40 | ScalarqosDiffServType39 | read-write | current | DiffServ Type 39 : IP ToS value = 156 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.41 | ScalarqosDiffServType40 | read-write | current | DiffServ Type 40 : IP ToS value = 160 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.42 | ScalarqosDiffServType41 | read-write | current | DiffServ Type 41 : IP ToS value = 164 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.43 | ScalarqosDiffServType42 | read-write | current | DiffServ Type 42 : IP ToS value = 168 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.44 | ScalarqosDiffServType43 | read-write | current | DiffServ Type 43 : IP ToS value = 172 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.45 | ScalarqosDiffServType44 | read-write | current | DiffServ Type 44 : IP ToS value = 176 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.46 | ScalarqosDiffServType45 | read-write | current | DiffServ Type 45 : IP ToS value = 180 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.47 | ScalarqosDiffServType46 | read-write | current | DiffServ Type 46 : IP ToS value = 184 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.48 | ScalarqosDiffServType47 | read-write | current | DiffServ Type 47 : IP ToS value = 188 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.49 | ScalarqosDiffServType48 | read-write | current | DiffServ Type 48 : IP ToS value = 192 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.50 | ScalarqosDiffServType49 | read-write | current | DiffServ Type 49 : IP ToS value = 196 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.51 | ScalarqosDiffServType50 | read-write | current | DiffServ Type 50 : IP ToS value = 200 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.52 | ScalarqosDiffServType51 | read-write | current | DiffServ Type 51 : IP ToS value = 204 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.53 | ScalarqosDiffServType52 | read-write | current | DiffServ Type 52 : IP ToS value = 208 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.54 | ScalarqosDiffServType53 | read-write | current | DiffServ Type 53 : IP ToS value = 212 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.55 | ScalarqosDiffServType54 | read-write | current | DiffServ Type 54 : IP ToS value = 216 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.56 | ScalarqosDiffServType55 | read-write | current | DiffServ Type 55 : IP ToS value = 220 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.57 | ScalarqosDiffServType56 | read-write | current | DiffServ Type 56 : IP ToS value = 224 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.58 | ScalarqosDiffServType57 | read-write | current | DiffServ Type 57 : IP ToS value = 228 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.59 | ScalarqosDiffServType58 | read-write | current | DiffServ Type 58 : IP ToS value = 232 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.60 | ScalarqosDiffServType59 | read-write | current | DiffServ Type 59 : IP ToS value = 236 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.61 | ScalarqosDiffServType60 | read-write | current | DiffServ Type 60 : IP ToS value = 240 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.62 | ScalarqosDiffServType61 | read-write | current | DiffServ Type 61 : IP ToS value = 244 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.63 | ScalarqosDiffServType62 | read-write | current | DiffServ Type 62 : IP ToS value = 248 |
| 1.3.6.1.4.1.171.10.75.14.12.6.1.64 | ScalarqosDiffServType63 | read-write | current | DiffServ Type 63 : IP ToS value = 252 |
| 1.3.6.1.4.1.171.10.75.14.12.7 | NodeqosPriSettings | |||
| 1.3.6.1.4.1.171.10.75.14.12.7.1 | TableqosPriSettingsTable | not-accessible | current | A list of port priority settings. |
| 1.3.6.1.4.1.171.10.75.14.12.7.1.1 | RowqosPriSettingsEntry | not-accessible | current | A list of port priority settings Entries. |
| 1.3.6.1.4.1.171.10.75.14.12.7.1.1.1 | ColumnqosPriSetPortIndex | read-only | current | A port identifier that is in the range of 1 to ifNumber. |
| 1.3.6.1.4.1.171.10.75.14.12.7.1.1.2 | ColumnqosPriSetPortType | read-write | current | The port priority setting type. (ex. none = 0, port mapping = 1, 802.1p = 2, DSCP = 4. If you want enable 802.1p & DSCP, the value is 2 + 4 = 6. |
| 1.3.6.1.4.1.171.10.75.14.12.8 | NodeqosAclPrioritySettings | |||
| 1.3.6.1.4.1.171.10.75.14.12.8.1 | TableaclQosTable | not-accessible | current | A list of priority by acl setting. |
| 1.3.6.1.4.1.171.10.75.14.12.8.1.1 | RowaclQosEntry | not-accessible | current | A list of priority by acl setting entry. |
| 1.3.6.1.4.1.171.10.75.14.12.8.1.1.1 | ColumnaclQosIndex | read-only | current | Index of priority by acl setting. |
| 1.3.6.1.4.1.171.10.75.14.12.8.1.1.2 | ColumnaclQosType | read-write | current | Type of priority by acl setting. |
| 1.3.6.1.4.1.171.10.75.14.12.8.1.1.3 | ColumnaclQosMACAddr | read-write | current | Dst MAC of priority by acl setting. |
| 1.3.6.1.4.1.171.10.75.14.12.8.1.1.4 | ColumnaclQosIPAddr | read-write | current | Dst IP of priority by acl setting |
| 1.3.6.1.4.1.171.10.75.14.12.8.1.1.5 | ColumnaclQosTCPUDPPort | read-write | current | Dst TCP/UDP port of priority by acl setting |
| 1.3.6.1.4.1.171.10.75.14.12.8.1.1.6 | ColumnaclQosVlanID | read-write | current | VLAN ID of priority by acl setting |
| 1.3.6.1.4.1.171.10.75.14.12.8.1.1.7 | ColumnaclQosProtocol | read-write | current | Ip protocol number of priority by acl setting |
| 1.3.6.1.4.1.171.10.75.14.12.8.1.1.8 | ColumnaclQosAssignClass | read-write | current | Be mapped class of priority by acl setting. |
| 1.3.6.1.4.1.171.10.75.14.12.8.1.1.9 | ColumnaclQosStatus | read-write | current | Status of priority by acl setting. |
| 1.3.6.1.4.1.171.10.75.14.13 | NodecompanyTrafficMgmt | |||
| 1.3.6.1.4.1.171.10.75.14.13.1 | NodebandwidthCtrlSettings | |||
| 1.3.6.1.4.1.171.10.75.14.13.1.2 | TablebandwidthCtrlTable | not-accessible | current | A table to control the rate limiting parameters either for the entire switch or for each interface in the switch. |
| 1.3.6.1.4.1.171.10.75.14.13.1.2.1 | RowbandwidthCtrlEntry | not-accessible | current | An entry appears in this table for each physical interface in the switch. |
| 1.3.6.1.4.1.171.10.75.14.13.1.2.1.1 | ColumnbandwidthCtrlIndex | read-only | current | The interface index for which the configuration in this entry applies. |
| 1.3.6.1.4.1.171.10.75.14.13.1.2.1.2 | ColumnbandwidthCtrlTxThreshold | read-write | current | Configures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed.… |
| 1.3.6.1.4.1.171.10.75.14.13.1.2.1.3 | ColumnbandwidthCtrlRxThreshold | read-write | current | Allows to configure the limiting value for the maximum number of receive packets that can be transmitted per second over this interface. Setting this object to… |
| 1.3.6.1.4.1.171.10.75.14.13.3 | NodebroadcastStormCtrlSettings | |||
| 1.3.6.1.4.1.171.10.75.14.13.3.1 | ScalarbroadcastStormCtrlGlobalOnOff | read-write | current | This object indicates storm control function is enabled or disabled for device. When you enable broadcast storm control function, D-Link Smart Switches will al… |
| 1.3.6.1.4.1.171.10.75.14.13.3.2 | ScalarbroadcastStormCtrlLimitType | read-write | current | This object indicates storm control function is control broadcast packet or multicast packet or dlf packet. |
| 1.3.6.1.4.1.171.10.75.14.13.3.3 | ScalarbroadcastStormCtrlThreshold | read-write | current | Allows to configure the limiting value for the maximum number of Kbits/sec that can be transmitted per second over this interface. Setting this object to the v… |
| 1.3.6.1.4.1.171.10.75.14.13.4 | NodetrafficCtrlSettings | |||
| 1.3.6.1.4.1.171.10.75.14.13.4.1 | ScalartrafficCtrlTrap | read-write | current | The trap setting of traffic control. |
| 1.3.6.1.4.1.171.10.75.14.13.4.2 | TabletrafficCtrlTable | not-accessible | current | The traffic control table. |
| 1.3.6.1.4.1.171.10.75.14.13.4.2.1 | RowtrafficCtrlEntry | not-accessible | current | The traffic control entry. |
| 1.3.6.1.4.1.171.10.75.14.13.4.2.1.1 | ColumntrafficCtrlIndex | read-only | current | The traffic control index. |
| 1.3.6.1.4.1.171.10.75.14.13.4.2.1.2 | ColumntrafficCtrlActionMode | read-write | current | The action mode of traffic control. |
| 1.3.6.1.4.1.171.10.75.14.13.4.2.1.3 | ColumntrafficCtrlType | read-write | current | The control type of traffic control. (b: Broadcast, m: Multicast, u: Unknown Unicast) |
| 1.3.6.1.4.1.171.10.75.14.13.4.2.1.4 | ColumntrafficCtrlThreshold | read-write | current | The threshold of traffic control. |
| 1.3.6.1.4.1.171.10.75.14.13.4.2.1.5 | ColumntrafficCtrlCountDown | read-write | current | The count down value of traffic control. |
| 1.3.6.1.4.1.171.10.75.14.13.4.2.1.6 | ColumntrafficCtrlTimeInterval | read-write | current | The time interval of traffic control. |
| 1.3.6.1.4.1.171.10.75.14.14 | NodecompanySecurity | |||
| 1.3.6.1.4.1.171.10.75.14.14.1 | NodesecurityTrustedHost | |||
| 1.3.6.1.4.1.171.10.75.14.14.1.1 | ScalartrustedHostStatus | read-write | current | This object indicates trusted host function is enabled or disabled. When trusted host function is enabled, D-Link Smart Switches will only allow hosts which yo… |
| 1.3.6.1.4.1.171.10.75.14.14.1.2 | TabletrustedHostTable | not-accessible | current | A table to configure trusted host in the system. |
| 1.3.6.1.4.1.171.10.75.14.14.1.2.1 | RowtrustedHostEntry | not-accessible | current | Each entry in this table represents rules for particular trusted host. |
| 1.3.6.1.4.1.171.10.75.14.14.1.2.1.1 | ColumntrustedHostIpAddr | read-only | current | The IP address of host you allow to access to D-Link Smart Switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection. |
| 1.3.6.1.4.1.171.10.75.14.14.1.2.1.2 | ColumntrustedHostIpMask | read-only | current | Used to mask with IP address, it allow you set a subnet as a trusted host entry. |
| 1.3.6.1.4.1.171.10.75.14.14.1.2.1.3 | ColumntrustedHostRowStatus | read-create | current | The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
| 1.3.6.1.4.1.171.10.75.14.14.2 | NodesecurityPortSecurity | |||
| 1.3.6.1.4.1.171.10.75.14.14.2.1 | TableportSecTable | not-accessible | current | A table to control port security features of the device. |
| 1.3.6.1.4.1.171.10.75.14.14.2.1.1 | RowportSecEntry | not-accessible | current | An entry appears in port security table for each interface in the system. |
| 1.3.6.1.4.1.171.10.75.14.14.2.1.1.1 | ColumnportSecIndex | read-only | current | The interface index for which the configuration in this entry applies. |
| 1.3.6.1.4.1.171.10.75.14.14.2.1.1.2 | ColumnportSecState | read-write | current | Enable / disable port security admin state for the interface. A given ports' dynamic MAC address learning will be stopped such that the current source MAC addr… |
| 1.3.6.1.4.1.171.10.75.14.14.2.1.1.3 | ColumnportSecMLA | read-write | current | Configures interface port security maximum learning address numbers. When given ports' admin state is enabled, allows forwarding table learning address number.… |
| 1.3.6.1.4.1.171.10.75.14.14.2.1.1.4 | ColumnportSecLockAddrMode | read-write | current | Configures port security lock address mode for the interface. deleteOnReset : The locked addresses will not age out until the Switch has been reset. deleteOnTi… |
| 1.3.6.1.4.1.171.10.75.14.14.2.2 | TableportSecFDBPermanentTable | not-accessible | current | A table to control port security FDB Permanent of the device. |
| 1.3.6.1.4.1.171.10.75.14.14.2.2.1 | RowportSecFDBPermanentEntry | not-accessible | current | An entry appears in port security table for each interface in the system. |
| 1.3.6.1.4.1.171.10.75.14.14.2.2.1.1 | ColumnportSecFDBPermIndex | read-only | current | The index of the port security MAC entry. |
| 1.3.6.1.4.1.171.10.75.14.14.2.2.1.2 | ColumnportSecFDBPermVlanID | read-only | current | The VLAN ID of the port security MAC entry. |
| 1.3.6.1.4.1.171.10.75.14.14.2.2.1.3 | ColumnportSecFDBPermMac | read-only | current | The MAC address associated of the port security MAC entry. |
| 1.3.6.1.4.1.171.10.75.14.14.2.2.1.4 | ColumnportSecFDBPermPort | read-only | current | The forwarding port of the port security MAC entry. |
| 1.3.6.1.4.1.171.10.75.14.14.3 | NodesecurityARPSpoofPrevent | |||
| 1.3.6.1.4.1.171.10.75.14.14.3.1 | TableaRPSpoofPreventTable | not-accessible | current | A table to control ARP Spoofing prevention for the entire switch or for each interface in the switch. |
| 1.3.6.1.4.1.171.10.75.14.14.3.1.1 | RowaRPSpoofPreventEntry | not-accessible | current | An entry appears in this table for each interface in the system. |
| 1.3.6.1.4.1.171.10.75.14.14.3.1.1.1 | ColumnaRPSpoofPreventIpAddr | not-accessible | current | Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'. |
| 1.3.6.1.4.1.171.10.75.14.14.3.1.1.2 | ColumnaRPSpoofPreventMacAddress | read-write | current | Ethernet Mac Address. |
| 1.3.6.1.4.1.171.10.75.14.14.3.1.1.3 | ColumnaRPSpoofPreventPortList | read-write | current | Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch throug… |
| 1.3.6.1.4.1.171.10.75.14.14.3.1.1.4 | ColumnaRPSpoofPreventRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.10.75.14.14.4 | NodeipMacPortBinding | |||
| 1.3.6.1.4.1.171.10.75.14.14.4.1 | ScalaripMacPortBindingSystemMode | read-write | current | The system wide ACL mode in IPMB. |
| 1.3.6.1.4.1.171.10.75.14.14.4.2 | ScalaripMacPortBindingTrapLogEnable | read-write | current | The trap event option in IPMB. |
| 1.3.6.1.4.1.171.10.75.14.14.4.3 | ScalaripMacPortBindingEnabledPortList | read-write | current | Specifies the port numbers which check incoming IP address and MAC address if issIpMacPortBindingStatus is enable. |
| 1.3.6.1.4.1.171.10.75.14.14.4.4 | ScalarallowZeroIPPortList | read-write | current | Specifies the port numbers which don't check incoming IP address and MAC address if issIpMacPortBindingStatus is enable. |
| 1.3.6.1.4.1.171.10.75.14.14.4.5 | TableipMacPortBindingTable | not-accessible | current | A table to control IP-MAC-Port Binding features either for the entire switch or for each interface in the switch. Parameters in this table are valid only when … |
| 1.3.6.1.4.1.171.10.75.14.14.4.5.1 | RowipMacPortBindingEntry | not-accessible | current | An entry appears in this table for each interface in the system. |
| 1.3.6.1.4.1.171.10.75.14.14.4.5.1.1 | ColumnipMacPortBindingIpAddr | not-accessible | current | Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'. |
| 1.3.6.1.4.1.171.10.75.14.14.4.5.1.2 | ColumnipMacPortBindingMacAddress | not-accessible | current | Ethernet Mac Address. |
| 1.3.6.1.4.1.171.10.75.14.14.4.5.1.3 | ColumnipMacPortBindingPortList | read-write | current | Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch throug… |
| 1.3.6.1.4.1.171.10.75.14.14.4.5.1.5 | ColumnipMacPortBindingRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.10.75.14.14.4.6 | TablemacBlockListTable | not-accessible | current | An entry appears in this table for each interface in the system. |
| 1.3.6.1.4.1.171.10.75.14.14.4.6.1 | RowmacBlockListEntry | not-accessible | current | An entry appears in this table for each interface in the system. |
| 1.3.6.1.4.1.171.10.75.14.14.4.6.1.1 | ColumnmacBlockListMacAddr | not-accessible | current | Blocked Mac Address. |
| 1.3.6.1.4.1.171.10.75.14.14.4.6.1.2 | ColumnmacBlockListVLANID | not-accessible | current | Blocked IP. |
| 1.3.6.1.4.1.171.10.75.14.14.4.6.1.3 | ColumnmacBlockListPort | not-accessible | current | Blocked port. |
| 1.3.6.1.4.1.171.10.75.14.14.4.6.1.4 | ColumnmacBlockListRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.10.75.14.14.5 | NodesecuritySSL | |||
| 1.3.6.1.4.1.171.10.75.14.14.5.1 | ScalarsslSecurityHttpStatus | read-write | current | This object is for enabling or disabling secure HTTP in the system. |
| 1.3.6.1.4.1.171.10.75.14.14.5.2 | NodesslCiphers | |||
| 1.3.6.1.4.1.171.10.75.14.14.5.2.1 | ScalarsslCipherSuiteList | read-write | current | This object is to configure the cipher-suites list. |
| 1.3.6.1.4.1.171.10.75.14.14.7 | NodesecurityDhcpServerScreen | |||
| 1.3.6.1.4.1.171.10.75.14.14.7.1 | ScalardhcpServerScreenEnablePortlist | read-write | current | To enable or disable DHCP Server Screening port list. |
| 1.3.6.1.4.1.171.10.75.14.14.7.2 | TablefilterDHCPServerTable | not-accessible | current | A table to control filter DHCP Server for the entire switch or for each interface in the switch. |
| 1.3.6.1.4.1.171.10.75.14.14.7.2.1 | RowfilterDHCPServerEntry | not-accessible | current | An entry appears in this table for each interface in the system. |
| 1.3.6.1.4.1.171.10.75.14.14.7.2.1.1 | ColumnfilterDHCPServerIpAddr | not-accessible | current | Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'. |
| 1.3.6.1.4.1.171.10.75.14.14.7.2.1.2 | ColumnfilterDHCPServerClientMacAddr | not-accessible | current | Ethernet Mac Address. |
| 1.3.6.1.4.1.171.10.75.14.14.7.2.1.3 | ColumnfilterDHCPServerPortList | read-write | current | Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch throug… |
| 1.3.6.1.4.1.171.10.75.14.14.7.2.1.4 | ColumnfilterDHCPServerRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.10.75.14.14.8 | NodesecuritySSH | |||
| 1.3.6.1.4.1.171.10.75.14.14.8.1 | ScalarsshSecurityStatus | read-write | current | This object is for enabling or disabling ssh in the system. |
| 1.3.6.1.4.1.171.10.75.14.14.8.2 | ScalarsshMaxAuthFailAttempts | read-write | current | This object indicates the max auth fail retry attempt times. |
| 1.3.6.1.4.1.171.10.75.14.14.8.3 | ScalarsshSessionKeyRekeying | read-write | current | This object indicates one SSH session rekey time interval. |
| 1.3.6.1.4.1.171.10.75.14.14.8.4 | ScalarsshMaxSession | read-write | current | This object indicates max SSH session number supported in system. |
| 1.3.6.1.4.1.171.10.75.14.14.8.5 | ScalarsshConnectionTimeout | read-write | current | This object indicates SSH connection timeout value. |
| 1.3.6.1.4.1.171.10.75.14.14.8.6 | ScalarsshAuthenMethodPassWordAdmin | read-write | current | The object indicates authen method password is enabled or disabled. |
| 1.3.6.1.4.1.171.10.75.14.14.8.7 | ScalarsshAuthenMethodPubKeyAdmin | read-write | current | The object indicates authen method public-key is enabled or disabled. |
| 1.3.6.1.4.1.171.10.75.14.14.8.8 | ScalarsshAuthenMethodHostKeyAdmin | read-write | current | The object indicates authen method host-key is enabled or disabled. |
| 1.3.6.1.4.1.171.10.75.14.14.8.9 | ScalarsshCipherSuiteList | read-write | current | This object is to configure the cipher-suites list. |
| 1.3.6.1.4.1.171.10.75.14.14.8.10 | ScalarsshMacSuiteList | read-write | current | This object is to configure the MAC-list. |
| 1.3.6.1.4.1.171.10.75.14.14.8.11 | ScalarsshPublKeyRSAAdmin | read-write | current | The object indicates Public key generating algorithm RSA is enabled or disabled. |
| 1.3.6.1.4.1.171.10.75.14.14.8.12 | TablesshUserInfoTable | not-accessible | current | A table to configure SSH user auth in the system. |
| 1.3.6.1.4.1.171.10.75.14.14.8.12.1 | RowsshUserInfoEntry | not-accessible | current | An entry to configure user auth in the system. |
| 1.3.6.1.4.1.171.10.75.14.14.8.12.1.1 | ColumnsshUserInfoID | read-only | current | The Schedule identifier. The maximum number of Schedule entry is the number of ports supported PoE function. The value must be between 1 and 8. |
| 1.3.6.1.4.1.171.10.75.14.14.8.12.1.2 | ColumnsshUserInfoUserName | read-only | current | The ssh user name associated with the SSH suer Info. entry (e.g., `admin, user'). |
| 1.3.6.1.4.1.171.10.75.14.14.8.12.1.3 | ColumnsshUserInfoAuth | read-write | current | The object indicates which auth used by the user. |
| 1.3.6.1.4.1.171.10.75.14.14.8.12.1.4 | ColumnsshUserInfoHostName | read-write | current | The ssh host name associated with the SSH suer Info. entry (e.g., `DUT1, DUT2'). |
| 1.3.6.1.4.1.171.10.75.14.14.8.12.1.5 | ColumnsshUserInfoHostIp | read-write | current | SSH HostBased IP Address of the system. |
| 1.3.6.1.4.1.171.10.75.14.14.9 | NodesecurityTrafficSeg | |||
| 1.3.6.1.4.1.171.10.75.14.14.9.1 | TabletrafficSegTable | not-accessible | current | A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. Th… |
| 1.3.6.1.4.1.171.10.75.14.14.9.1.1 | RowtrafficSegEntry | not-accessible | current | There is one entry in this table for each created port-channel port |
| 1.3.6.1.4.1.171.10.75.14.14.9.1.1.1 | ColumntrafficSegIfIndex | read-only | current | The ifIndex of the port-channel(Aggregator's interface index). |
| 1.3.6.1.4.1.171.10.75.14.14.9.1.1.2 | ColumntrafficSegMemberList | read-write | current | Port list of port channel. |
| 1.3.6.1.4.1.171.10.75.14.14.10 | NodesecurityAAC | |||
| 1.3.6.1.4.1.171.10.75.14.14.10.1 | ScalaraacAuthenAdminState | read-write | current | This object indicates the Access Authentication is enable or disable. |
| 1.3.6.1.4.1.171.10.75.14.14.10.2 | ScalaraacAuthParamResponseTimeout | read-write | current | Timeout in second for login authentication response. |
| 1.3.6.1.4.1.171.10.75.14.14.10.3 | ScalaraacAuthParamAttempt | read-write | current | The amount for login authentication, if login failure exceed, connection or access would be locked. |
| 1.3.6.1.4.1.171.10.75.14.14.10.4 | NodeaacAPAuthMethodGroup | |||
| 1.3.6.1.4.1.171.10.75.14.14.10.4.1 | NodeaacAPLoginMethod | |||
| 1.3.6.1.4.1.171.10.75.14.14.10.4.1.1 | ScalaraacAPConsoleLoginMethod | read-write | current | Specify the way which has to execute authentication while login the system and the method for authentication.Access system via local console |
| 1.3.6.1.4.1.171.10.75.14.14.10.4.1.2 | ScalaraacAPTelnetLoginMethod | read-write | current | Specify the way which has to execute authentication while login the system and the method for authentication.Access system via telnet. |
| 1.3.6.1.4.1.171.10.75.14.14.10.4.1.3 | ScalaraacAPSSHLoginMethod | read-write | current | Specify the way which has to execute authentication while login the system and the method for authentication.Access system via SSH. |
| 1.3.6.1.4.1.171.10.75.14.14.10.4.1.4 | ScalaraacAPHttpLoginMethod | read-write | current | Specify the way which has to execute authentication while login the system and the method for authentication.Access system via HTTP. |
| 1.3.6.1.4.1.171.10.75.14.14.10.4.2 | NodeaacAPEnableMethod | |||
| 1.3.6.1.4.1.171.10.75.14.14.10.4.2.1 | ScalaraacAPConsoleEnableMethod | read-write | current | Specify the way which has to execute authentication while login the system and the method for authentication.Access system via local console. |
| 1.3.6.1.4.1.171.10.75.14.14.10.4.2.2 | ScalaraacAPTelnetEnableMethod | read-write | current | Specify the way which has to execute authentication while login the system and the method for authentication.Access system via telnet. |
| 1.3.6.1.4.1.171.10.75.14.14.10.4.2.3 | ScalaraacAPSSHEnableMethod | read-write | current | Specify the way which has to execute authentication while login the system and the method for authentication.Access system via SSH. |
| 1.3.6.1.4.1.171.10.75.14.14.10.4.2.4 | ScalaraacAPHttpEnableMethod | read-write | current | Specify the way which has to execute authentication while login the system and the method for authentication.Access system via HTTP. |
| 1.3.6.1.4.1.171.10.75.14.14.10.5 | TableaacServerGroupTable | not-accessible | current | A table that contains informations about server group. |
| 1.3.6.1.4.1.171.10.75.14.14.10.5.1 | RowaacServerGroupEntry | not-accessible | current | A list of the group including servers. |
| 1.3.6.1.4.1.171.10.75.14.14.10.5.1.1 | ColumnaacServerGroupIndex | read-only | current | A value that uniquely identifies this SwAACServerGroupEntry . |
| 1.3.6.1.4.1.171.10.75.14.14.10.5.1.2 | ColumnaacServerGroupName | read-write | current | A human-readable text string of the method group. The name is writable only if Group is new created, which the value of aacServerGroupRowStatus is 'notReady'. |
| 1.3.6.1.4.1.171.10.75.14.14.10.5.1.3 | ColumnaacServersInGroup | read-write | current | The list of servers in the group, each bit indicates a specified server ID. The server must be created before including it. |
| 1.3.6.1.4.1.171.10.75.14.14.10.5.1.4 | ColumnaacServerGroupRowStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.75.14.14.10.6 | TableaacServerInfoTable | not-accessible | current | A table that contains information about severs. |
| 1.3.6.1.4.1.171.10.75.14.14.10.6.1 | RowaacServerInfoEntry | not-accessible | current | A list of the information of server . |
| 1.3.6.1.4.1.171.10.75.14.14.10.6.1.1 | ColumnaacServerIndex | read-only | current | A value that uniquely identifies this SwAACServerGroupEntry. |
| 1.3.6.1.4.1.171.10.75.14.14.10.6.1.2 | ColumnaacServerIPAddr | read-write | current | The IP address of Server |
| 1.3.6.1.4.1.171.10.75.14.14.10.6.1.3 | ColumnaacServerAuthProtocol | read-write | current | The authentication protocol provided by the Server. |
| 1.3.6.1.4.1.171.10.75.14.14.10.6.1.4 | ColumnaacServerAuthPort | read-write | current | The TCP/IP port . |
| 1.3.6.1.4.1.171.10.75.14.14.10.6.1.5 | ColumnaacServerAuthKey | read-write | current | The key used while authentication process. |
| 1.3.6.1.4.1.171.10.75.14.14.10.6.1.6 | ColumnaacServerTimeout | read-write | current | Server response timeout . |
| 1.3.6.1.4.1.171.10.75.14.14.10.6.1.7 | ColumnaacServerRetryCount | read-write | current | The client retry count . |
| 1.3.6.1.4.1.171.10.75.14.14.10.6.1.8 | ColumnaacServerRowStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.75.14.14.10.7 | TableaacLoginMethodListTable | not-accessible | current | A table that contains information about Login authentication method lists. |
| 1.3.6.1.4.1.171.10.75.14.14.10.7.1 | RowaacLoginMethodListEntry | not-accessible | current | A list of the Authentication methods. |
| 1.3.6.1.4.1.171.10.75.14.14.10.7.1.1 | ColumnaacLoginMethodListIndex | read-only | current | A value that identifies this method list. |
| 1.3.6.1.4.1.171.10.75.14.14.10.7.1.2 | ColumnaacLoginMethodListName | read-write | current | A human-readable text string of the method list. |
| 1.3.6.1.4.1.171.10.75.14.14.10.7.1.3 | ColumnaacLoginMethod1 | read-write | current | The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. |
| 1.3.6.1.4.1.171.10.75.14.14.10.7.1.4 | ColumnaacLoginMethod2 | read-write | current | The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. |
| 1.3.6.1.4.1.171.10.75.14.14.10.7.1.5 | ColumnaacLoginMethod3 | read-write | current | The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. |
| 1.3.6.1.4.1.171.10.75.14.14.10.7.1.6 | ColumnaacLoginMethod4 | read-write | current | The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. |
| 1.3.6.1.4.1.171.10.75.14.14.10.7.1.7 | ColumnaacLoginMethodListRowStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.75.14.14.10.8 | TableaacEnableMethodListTable | not-accessible | current | A table that contains information about Enable authentication method lists. |
| 1.3.6.1.4.1.171.10.75.14.14.10.8.1 | RowaacEnableMethodListEntry | not-accessible | current | A list of the Authentication methods. |
| 1.3.6.1.4.1.171.10.75.14.14.10.8.1.1 | ColumnaacEnableMethodListIndex | read-only | current | A value that identifies this method list. |
| 1.3.6.1.4.1.171.10.75.14.14.10.8.1.2 | ColumnaacEnableMethodListName | read-write | current | A human-readable text string of the method list. |
| 1.3.6.1.4.1.171.10.75.14.14.10.8.1.3 | ColumnaacEnableMethod1 | read-write | current | The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. |
| 1.3.6.1.4.1.171.10.75.14.14.10.8.1.4 | ColumnaacEnableMethod2 | read-write | current | The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. |
| 1.3.6.1.4.1.171.10.75.14.14.10.8.1.5 | ColumnaacEnableMethod3 | read-write | current | The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. |
| 1.3.6.1.4.1.171.10.75.14.14.10.8.1.6 | ColumnaacEnableMethod4 | read-write | current | The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. |
| 1.3.6.1.4.1.171.10.75.14.14.10.8.1.7 | ColumnaacEnableMethodListRowStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.75.14.14.10.9 | ScalaraacLocalEnablePassword | read-write | current | This object is used to set Local Enable Password. |
| 1.3.6.1.4.1.171.10.75.14.15 | NodecompanyACLGroup | |||
| 1.3.6.1.4.1.171.10.75.14.15.1 | NodeaclProfile | |||
| 1.3.6.1.4.1.171.10.75.14.15.1.1 | TableaclProfileTable | not-accessible | current | A table to ACL profile . |
| 1.3.6.1.4.1.171.10.75.14.15.1.1.1 | RowaclProfileEntry | not-accessible | current | Each entry in this table is a ACL profile. Index to the table is ACL profile ID. |
| 1.3.6.1.4.1.171.10.75.14.15.1.1.1.1 | ColumnaclProfileNo | read-only | current | The ACL Profile ID. The ID 1 to 50 is user-defined ACL, and the ID more than 50 is reserved for system-defined ACL. The user only allow to create user-defined … |
| 1.3.6.1.4.1.171.10.75.14.15.1.1.1.2 | ColumnaclProfileType | read-write | current | The ACL Profile type, possible value are l2 (1) - for MAC-based rule, l3 (2) - for IPv4-based rule, arpSP-permit(4) - for ARP Spoofing prevention entry, arpSP-… |
| 1.3.6.1.4.1.171.10.75.14.15.1.1.1.3 | ColumnaclProfileRuleCount | read-only | current | The number of rules in this profile. |
| 1.3.6.1.4.1.171.10.75.14.15.1.1.1.4 | ColumnaclProfileMask | read-write | current | Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT L2 DST-MAC 0 (LSB) L2 SRC-MAC 1 L2 VID … |
| 1.3.6.1.4.1.171.10.75.14.15.1.1.1.5 | ColumnaclProfileDstMacAddrMask | read-write | current | The ACL Profile destination MAC address mask. If DST-MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleDstMacAddr, to caculate… |
| 1.3.6.1.4.1.171.10.75.14.15.1.1.1.6 | ColumnaclProfileSrcMacAddrMask | read-write | current | The ACL Profile source MAC address mask. If SRC-MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleSrcMacAddr, to caculate a ra… |
| 1.3.6.1.4.1.171.10.75.14.15.1.1.1.7 | ColumnaclProfileIPProtocol | read-write | current | Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none. |
| 1.3.6.1.4.1.171.10.75.14.15.1.1.1.8 | ColumnaclProfileIPProtocolMask | read-write | current | The ACL Profile IP protocol mask. If aclProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule field,aclL3RuleProtocol,… |
| 1.3.6.1.4.1.171.10.75.14.15.1.1.1.9 | ColumnaclProfileDstIpAddrMask | read-write | current | The ACL Profile destination IP address mask. If DST-IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleDstIpAddr, to caculate a … |
| 1.3.6.1.4.1.171.10.75.14.15.1.1.1.10 | ColumnaclProfileSrcIpAddrMask | read-write | current | The ACL Profile source IP address mask. If SRC-IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleSrcIpAddr, to caculate a range… |
| 1.3.6.1.4.1.171.10.75.14.15.1.1.1.11 | ColumnaclProfileDstPortMask | read-write | current | The ACL Profile UDP/TCP destination port mask. If DST-PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpDstPort, to cac… |
| 1.3.6.1.4.1.171.10.75.14.15.1.1.1.12 | ColumnaclProfileSrcPortMask | read-write | current | The ACL Profile UDP/TCP source port mask. If SRC-PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpSrcPort, to caculate… |
| 1.3.6.1.4.1.171.10.75.14.15.1.1.1.13 | ColumnaclProfileArpSenderMacAddrMask | read-only | current | The ACL Profile Sender MAC mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format. |
| 1.3.6.1.4.1.171.10.75.14.15.1.1.1.14 | ColumnaclProfileArpSenderIpAddrMask | read-only | current | The ACL Profile Sender IP mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format. |
| 1.3.6.1.4.1.171.10.75.14.15.1.1.1.15 | ColumnaclProfileStatus | read-create | current | This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait… |
| 1.3.6.1.4.1.171.10.75.14.15.2 | NodeaclL2Rule | |||
| 1.3.6.1.4.1.171.10.75.14.15.2.1 | TableaclL2RuleTable | not-accessible | current | A table to configure L2 filter rules in the system. |
| 1.3.6.1.4.1.171.10.75.14.15.2.1.1 | RowaclL2RuleEntry | not-accessible | current | Each entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID. |
| 1.3.6.1.4.1.171.10.75.14.15.2.1.1.1 | ColumnaclL2AccessID | read-only | current | L2 Filter rule ID. |
| 1.3.6.1.4.1.171.10.75.14.15.2.1.1.2 | ColumnaclL2ProfileID | read-only | current | ACL Profile ID which this rule join. |
| 1.3.6.1.4.1.171.10.75.14.15.2.1.1.3 | ColumnaclL2RuleEtherType | read-write | current | The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '-1', which means the rule don't ca… |
| 1.3.6.1.4.1.171.10.75.14.15.2.1.1.4 | ColumnaclL2RuleDstMacAddr | read-write | current | Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero,which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.15.2.1.1.5 | ColumnaclL2RuleSrcMacAddr | read-write | current | Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero, which means the rule don't care this condition.. address |
| 1.3.6.1.4.1.171.10.75.14.15.2.1.1.6 | ColumnaclL2RuleVlanId | read-write | current | Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule… |
| 1.3.6.1.4.1.171.10.75.14.15.2.1.1.7 | ColumnaclL2Rule1pPriority | read-write | current | 802.1p priority to be matched with the packet. By Default, the value will be '-1', which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.15.2.1.1.8 | ColumnaclL2RuleDstMacAddrMask | read-only | current | The MAC address Mask work for Destination MAC address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.75.14.15.2.1.1.9 | ColumnaclL2RuleSrcMacAddrMask | read-only | current | The MAC address Mask work for Source MAC address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.75.14.15.2.1.1.10 | ColumnaclL2RuleInPortList | read-write | current | Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list. |
| 1.3.6.1.4.1.171.10.75.14.15.2.1.1.11 | ColumnaclL2RuleAction | read-write | current | Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding r… |
| 1.3.6.1.4.1.171.10.75.14.15.2.1.1.12 | ColumnaclL2RuleRateLimit | read-write | current | Rate limit for matched packet. |
| 1.3.6.1.4.1.171.10.75.14.15.2.1.1.13 | ColumnaclL2RuleReplaceDSCP | read-write | current | Replace DSCP for matched packet. |
| 1.3.6.1.4.1.171.10.75.14.15.2.1.1.14 | ColumnaclL2RuleStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.75.14.15.3 | NodeaclL3Rule | |||
| 1.3.6.1.4.1.171.10.75.14.15.3.1 | TableaclL3RuleTable | not-accessible | current | A table to configure L3 filter rules in the system. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1 | RowaclL3RuleEntry | not-accessible | current | Each entry in this table is a L3 filter rule. Index to the table is L3 filter number and Profile ID. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.1 | ColumnaclL3RuleAccessID | read-only | current | L3 Filter rule ID. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.2 | ColumnaclL3RuleProfileNo | read-only | current | The Profile ID which this rule join. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.3 | ColumnaclL3RuleProtocol | read-write | current | The type of protocol to be checked against the packet. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.4 | ColumnaclL3RuleProtocolMask | read-only | current | The IP protocol mask. This field is read-only and copy from it's Profile setting. It will work with the other field,aclL3RuleProtocol, to caculate a range of I… |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.5 | ColumnaclL3RuleICMPMessageType | read-write | current | The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action s… |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.6 | ColumnaclL3RuleICMPMessageCode | read-write | current | The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action s… |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.7 | ColumnaclL3RuleDstIpAddr | read-write | current | Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.8 | ColumnaclL3RuleSrcIpAddr | read-write | current | Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.9 | ColumnaclL3RuleDstIpAddrMask | read-only | current | The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.10 | ColumnaclL3RuleSrcIpAddrMask | read-only | current | The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.11 | ColumnaclL3RuleTcpUdpDstPort | read-write | current | The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.12 | ColumnaclL3RuleTcpUdpSrcPort | read-write | current | The TCP / UDP source port. The default value is -1, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.13 | ColumnaclL3RuleTcpUdpDstPortMask | read-only | current | The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.14 | ColumnaclL3RuleTcpUdpSrcPortMask | read-only | current | The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.15 | ColumnaclL3RuleTcpAckBit | read-create | current | The TCP ACK bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.16 | ColumnaclL3RuleTcpRstBit | read-create | current | The TCP RST bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.17 | ColumnaclL3RuleTcpUrgBit | read-create | current | The TCP Urg bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.18 | ColumnaclL3RuleTcpPshBit | read-create | current | The TCP Psh bit to be checked against the packet. The default value is 'dont-care'(-1). which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.19 | ColumnaclL3RuleTcpSynBit | read-create | current | The TCP Syn bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.20 | ColumnaclL3RuleTcpFinBit | read-create | current | The TCP Fin bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.21 | ColumnaclL3RuleDscp | read-create | current | The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.22 | ColumnaclL3RuleIgmpType | read-write | current | The IGMP Type to be checked against the packet.A default value is '-1', which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.23 | ColumnaclL3RulePortList | read-write | current | Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.24 | ColumnaclL3RuleAction | read-write | current | Specifies the action to be taken on the packet if the filter rule matches. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.25 | ColumnaclL3RuleRateLimit | read-write | current | Rate limit for matched packet. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.26 | ColumnaclL3RuleReplaceDSCP | read-write | current | ReplaceDSCP for matched packet. |
| 1.3.6.1.4.1.171.10.75.14.15.3.1.1.27 | ColumnaclL3RuleStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.75.14.16 | NodecompanySyslog | |||
| 1.3.6.1.4.1.171.10.75.14.16.1 | NodesyslogSettingGroup | |||
| 1.3.6.1.4.1.171.10.75.14.16.1.1 | ScalarsyslogEnable | read-write | current | This object is for enabling or disabling syslog alert features in the system and the syslog will save to flash or send to remote syslog server. System Logs rec… |
| 1.3.6.1.4.1.171.10.75.14.16.1.2 | ScalarsyslogSaveMode | read-write | current | This object is for choosing the method to save syslog into flash. |
| 1.3.6.1.4.1.171.10.75.14.16.1.3 | ScalarsyslogSaveMinutes | read-write | current | When savemode is time interval, it's used to set the interval minutes of system save syslog to flash. |
| 1.3.6.1.4.1.171.10.75.14.16.2 | NodesyslogServerGroup | |||
| 1.3.6.1.4.1.171.10.75.14.16.2.1 | TablesyslogServTable | not-accessible | current | The table of syslog remote server. |
| 1.3.6.1.4.1.171.10.75.14.16.2.1.1 | RowsyslogServEntry | not-accessible | current | The list of syslog remote server entry. |
| 1.3.6.1.4.1.171.10.75.14.16.2.1.1.1 | ColumnsyslogServIndex | read-only | current | The index of syslog remote server. |
| 1.3.6.1.4.1.171.10.75.14.16.2.1.1.2 | ColumnsyslogServAddr | read-write | current | The IP Address of syslog remote server. |
| 1.3.6.1.4.1.171.10.75.14.16.2.1.1.3 | ColumnsyslogServSeverity | read-write | current | Specifies the log level option to be set for a specific server. |
| 1.3.6.1.4.1.171.10.75.14.16.2.1.1.4 | ColumnsyslogServFacility | read-write | current | The Syslog standard facilities. The facility to be used when sending Syslog messages to this server. |
| 1.3.6.1.4.1.171.10.75.14.16.2.1.1.5 | ColumnsyslogServUDPport | read-write | current | The value is for setting UDP Port. |
| 1.3.6.1.4.1.171.10.75.14.16.2.1.1.6 | ColumnsyslogServSrvStatus | read-write | current | The status for this server. If enable, system will send message to this server. |
| 1.3.6.1.4.1.171.10.75.14.16.2.1.1.7 | ColumnsyslogServSrvRowStatus | read-write | current | Row status of this server entry. |
| 1.3.6.1.4.1.171.10.75.14.17 | NodecompanyLBD | |||
| 1.3.6.1.4.1.171.10.75.14.17.1 | ScalarsysLBDStateEnable | read-write | current | Enable/Disable Loopback detection function. The Loopback Detection function is used to detect the loop created by a specific port while Spanning Tree Protocol … |
| 1.3.6.1.4.1.171.10.75.14.17.2 | ScalarsysLBDInterval | read-write | current | Set a Loop detection Interval between 1 and 32767 seconds. The default is 2 seconds. This time interval to be used at counting time seconds to resend the CTP p… |
| 1.3.6.1.4.1.171.10.75.14.17.3 | ScalarsysLBDRecoverTime | read-write | current | This time interval to be used at counting time seconds to recover the disabled port automatically. The Loop Detection Recover Time can be set at 0 seconds, or … |
| 1.3.6.1.4.1.171.10.75.14.17.4 | TablesysLBDCtrlTable | not-accessible | current | A table to control Loopback detection features either for the entire switch or for each interface in the switch. |
| 1.3.6.1.4.1.171.10.75.14.17.4.1 | RowsysLBDCtrlEntry | not-accessible | current | An entry appears in this table for each interface in the system. |
| 1.3.6.1.4.1.171.10.75.14.17.4.1.1 | ColumnsysLBDCtrlIndex | read-only | current | The interface index of the port for which the configuration in this entry applies. |
| 1.3.6.1.4.1.171.10.75.14.17.4.1.2 | ColumnsysLBDPortStatus | read-write | current | Provides control to per port enable or disable the loopback detection function. Default is disabled. |
| 1.3.6.1.4.1.171.10.75.14.17.4.1.3 | ColumnsysLBDPortLoopStatus | read-only | current | The loop status for this port. |
| 1.3.6.1.4.1.171.10.75.14.18 | NodecompanyMirror | |||
| 1.3.6.1.4.1.171.10.75.14.18.1 | ScalarsysMirrorStatus | read-write | current | Enable/Disable Port Mirroring function. Default is disabled. Port Mirroring is a method of monitoring network traffic that forwards a copy of each incoming and… |
| 1.3.6.1.4.1.171.10.75.14.18.2 | ScalarsysMirrorTargetPort | read-write | current | Specifies the port to which the mirrored traffic in the system is to be copied. |
| 1.3.6.1.4.1.171.10.75.14.18.3 | ScalarsysMirrorCtrlIngressMirroring | read-write | current | Provides control to enable or disable mirroring of ingress traffic over this interface to the mirrored-to port. |
| 1.3.6.1.4.1.171.10.75.14.18.4 | ScalarsysMirrorCtrlEgressMirroring | read-write | current | Provides control to enable or disable mirroring of egress traffic over this interface to the mirrored-to port. |
| 1.3.6.1.4.1.171.10.75.14.19 | NodecompanyStaticMcast | |||
| 1.3.6.1.4.1.171.10.75.14.19.1 | TablestaticMcastTable | not-accessible | current | A list of the Static MACs |
| 1.3.6.1.4.1.171.10.75.14.19.1.1 | RowstaticMcastEntry | not-accessible | current | A Static MAC entry containing the mac and forwarding port. |
| 1.3.6.1.4.1.171.10.75.14.19.1.1.1 | ColumnstaticMcastVlanID | read-only | current | The VLAN ID of the static MAC entry. |
| 1.3.6.1.4.1.171.10.75.14.19.1.1.2 | ColumnstaticMcastMac | read-only | current | The MAC address associated of the static MAC entry. |
| 1.3.6.1.4.1.171.10.75.14.19.1.1.3 | ColumnstaticMcastEgressPorts | read-only | current | The set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast MAC address must be forwarded, regardless of … |
| 1.3.6.1.4.1.171.10.75.14.19.1.1.4 | ColumnstaticMcastStatus | read-write | current | The status of an entry in the Static Mcast Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
| 1.3.6.1.4.1.171.10.75.14.20 | NodecompanySNTPSetting | |||
| 1.3.6.1.4.1.171.10.75.14.20 | NodestormOccurred | Storm Occurred. | ||
| 1.3.6.1.4.1.171.10.75.14.20.1 | ScalarsysSNTPTimeSeconds | read-write | current | This object is for setting the system time in seconds from Epoch (00:00:00 UTC, January 1, 2009). Notice : input value must larger than 1230768000 (00:00:00 UT… |
| 1.3.6.1.4.1.171.10.75.14.20.2 | ScalarsysSNTPFirstServer | read-write | current | SNTP First Server's IP Address |
| 1.3.6.1.4.1.171.10.75.14.20.3 | ScalarsysSNTPSecondServer | read-write | current | SNTP Second Server's IP Address |
| 1.3.6.1.4.1.171.10.75.14.20.4 | ScalarsysSNTPPollInterval | read-write | current | SNTP Poll Interval In Seconds (30-99999) |
| 1.3.6.1.4.1.171.10.75.14.20.5 | ScalarsysSNTPState | read-write | current | Enable/Disable SNTP function in the system. |
| 1.3.6.1.4.1.171.10.75.14.20.6 | ScalarsysSNTPDSTOffset | read-write | current | This object is for Daylight Saving Time Offset In (30/60/90/120) Minutes. |
| 1.3.6.1.4.1.171.10.75.14.20.7 | ScalarsysSNTPGMTMinutes | read-write | current | Specifies the Time Zone Offset from GMT in +/- Minutes. (+780 ~ -720) |
| 1.3.6.1.4.1.171.10.75.14.20.8 | ScalarsysSNTPDSTStartMon | read-write | current | The start month of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.75.14.20.9 | ScalarsysSNTPDSTStartDay | read-write | current | The start day of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.75.14.20.10 | ScalarsysSNTPDSTStartHour | read-write | current | The start hour of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.75.14.20.11 | ScalarsysSNTPDSTStartMin | read-write | current | The start minute of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.75.14.20.12 | ScalarsysSNTPDSTEndMon | read-write | current | The end month of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.75.14.20.13 | ScalarsysSNTPDSTEndDay | read-write | current | The end day of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.75.14.20.14 | ScalarsysSNTPDSTEndHour | read-write | current | The end hour of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.75.14.20.15 | ScalarsysSNTPDSTEndMin | read-write | current | The end minute of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.75.14.20.16 | ScalarsysSNTPDSTState | read-write | current | This object is for Annual(1) or Disabled(2) DST state in the system. |
| 1.3.6.1.4.1.171.10.75.14.21 | NodecompanyVoiceVlan | |||
| 1.3.6.1.4.1.171.10.75.14.21 | NodestormCleared | Storm Cleared. | ||
| 1.3.6.1.4.1.171.10.75.14.21.1 | NodevoicevlanSystem | |||
| 1.3.6.1.4.1.171.10.75.14.21.1.2 | ScalarvoiceVlanMode | read-write | current | Voice VLAN is a feature that allows you to automatically place the voice traffic from IP phone to an assigned VLAN to enhance the VoIP service. This object is … |
| 1.3.6.1.4.1.171.10.75.14.21.1.3 | ScalarvoiceVlanId | read-write | current | The ID of VLAN that you want the voice traffic to be in. It must be a exist vlan id. |
| 1.3.6.1.4.1.171.10.75.14.21.1.4 | ScalarvoiceVlanTimeout | read-write | current | A period of time in hour to remove a port from voice VLAN if the port is an automatic VLAN member. The Timeout range is 1~120 hours. Default aging time is 1 ho… |
| 1.3.6.1.4.1.171.10.75.14.21.1.5 | ScalarvoiceVlanPriority | read-write | current | The 802.1p priority levels of the traffic in the Voice VLAN. |
| 1.3.6.1.4.1.171.10.75.14.21.1.6 | TablevoicevlanPortControlTable | not-accessible | current | A table that contains Voice Vlan Port Control configuration information. |
| 1.3.6.1.4.1.171.10.75.14.21.1.6.1 | RowvoicevlanPortControlEntry | not-accessible | current | A list of Voice Vlan Control configuration parameters for each Port on this device. |
| 1.3.6.1.4.1.171.10.75.14.21.1.6.1.1 | ColumnvoicevlanPortControlIndex | read-only | current | The voice vlan port index. |
| 1.3.6.1.4.1.171.10.75.14.21.1.6.1.2 | ColumnvoicevlanPortAutoDetection | read-write | current | This object is for enabling or disabling Voice Vlan Auto Detection in the port. If the auto detection is enable, switch will add this port to the voice VLAN au… |
| 1.3.6.1.4.1.171.10.75.14.21.1.6.1.3 | ColumnvoicevlanPortState | read-only | current | This object indicates Voice vlan state to this Port. manual - this port is a static member of voice vlan. dynamic - this port is a dynamic member of voice vlan… |
| 1.3.6.1.4.1.171.10.75.14.21.2 | NodevoicevlanOUI | |||
| 1.3.6.1.4.1.171.10.75.14.21.2.1 | TablevoicevlanOUITable | not-accessible | current | A voice vlan OUI entry containing the description and mac. |
| 1.3.6.1.4.1.171.10.75.14.21.2.1.1 | RowvoicevlanOUIEntry | not-accessible | current | A voice vlan OUI entry containing the description and mac. |
| 1.3.6.1.4.1.171.10.75.14.21.2.1.1.1 | ColumnvoicevlanOUITelephonyOUI | read-only | current | An Organizationally Unique Identifier (OUI) is a 24-bit number that is purchased from the IEEE Registration Authority. This identifier uniquely identifies a ve… |
| 1.3.6.1.4.1.171.10.75.14.21.2.1.1.2 | ColumnvoicevlanOUIDescription | read-write | current | The Description for the OUI. |
| 1.3.6.1.4.1.171.10.75.14.21.2.1.1.3 | ColumnvoicevlanOUIMask | read-only | current | Voice vlan OUI Mask. Always be FF:FF:FF:00:00:00. |
| 1.3.6.1.4.1.171.10.75.14.21.2.1.1.4 | ColumnvoicevlanOUIStatus | read-write | current | This object indicates the status of this entry. To create a new entry, you must set the voicevlanOUIStatus to be CreateAndGo, then this entry will turn to be A… |
| 1.3.6.1.4.1.171.10.75.14.22 | NodecompanyRMON | |||
| 1.3.6.1.4.1.171.10.75.14.22 | NodemacNotification | Learning Mac Notification. | ||
| 1.3.6.1.4.1.171.10.75.14.22.1 | ScalarrmonGlobalState | read-write | current | This object is for enabling or disabling RMON function. |
| 1.3.6.1.4.1.171.10.75.14.22.2 | NodermonStatistics | |||
| 1.3.6.1.4.1.171.10.75.14.22.2.1 | TablermonStatsTable | not-accessible | current | A list of Ethernet statistics entries. |
| 1.3.6.1.4.1.171.10.75.14.22.2.1.1 | RowrmonStatsEntry | not-accessible | current | A collection of statistics kept for a particular Ethernet interface. As an example, an instance of the etherStatsPkts object might be named etherStatsPkts.1 |
| 1.3.6.1.4.1.171.10.75.14.22.2.1.1.1 | ColumnrmonStatsIndex | read-only | current | The value of this object uniquely identifies this etherStats entry. |
| 1.3.6.1.4.1.171.10.75.14.22.2.1.1.2 | ColumnrmonStatsDataSource | read-create | current | This object identifies the source of the data that this etherStats entry is configured to analyze. This source can be any ethernet interface on this device. In… |
| 1.3.6.1.4.1.171.10.75.14.22.2.1.1.3 | ColumnrmonStatsOwner | read-create | current | The entity that configured this entry and is therefore using the resources assigned to it. |
| 1.3.6.1.4.1.171.10.75.14.22.2.1.1.4 | ColumnrmonStatsStatus | read-create | current | The status of this etherStats entry. |
| 1.3.6.1.4.1.171.10.75.14.22.3 | NodermonHistory | |||
| 1.3.6.1.4.1.171.10.75.14.22.3.1 | TablermonHistoryTable | not-accessible | current | A list of history control entries. |
| 1.3.6.1.4.1.171.10.75.14.22.3.1.1 | RowrmonHistoryEntry | not-accessible | current | A list of parameters that set up a periodic sampling of statistics. As an example, an instance of the historyControlInterval object might be named historyContr… |
| 1.3.6.1.4.1.171.10.75.14.22.3.1.1.1 | ColumnrmonHistoryIndex | read-only | current | An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on t… |
| 1.3.6.1.4.1.171.10.75.14.22.3.1.1.2 | ColumnrmonHistoryDataSource | read-create | current | This object identifies the source of the data for which historical data was collected and placed in a media-specific table on behalf of this historyControlEntr… |
| 1.3.6.1.4.1.171.10.75.14.22.3.1.1.3 | ColumnrmonHistoryBucketsRequested | read-create | current | The requested number of discrete time intervals over which data is to be saved in the part of the media-specific table associated with this historyControlEntry… |
| 1.3.6.1.4.1.171.10.75.14.22.3.1.1.4 | ColumnrmonHistoryInterval | read-create | current | The interval in seconds over which the data is sampled for each bucket in the part of the media-specific table associated with this historyControlEntry. This i… |
| 1.3.6.1.4.1.171.10.75.14.22.3.1.1.5 | ColumnrmonHistoryOwner | read-create | current | The entity that configured this entry and is therefore using the resources assigned to it. |
| 1.3.6.1.4.1.171.10.75.14.22.3.1.1.6 | ColumnrmonHistoryStatus | read-create | current | The status of this historyControl entry. Each instance of the media-specific table associated with this historyControlEntry will be deleted by the agent if thi… |
| 1.3.6.1.4.1.171.10.75.14.22.4 | NodermonAlarm | |||
| 1.3.6.1.4.1.171.10.75.14.22.4.1 | TablermonAlarmTable | not-accessible | current | A list of alarm entries. |
| 1.3.6.1.4.1.171.10.75.14.22.4.1.1 | RowrmonAlarmEntry | not-accessible | current | A list of parameters that set up a periodic checking for alarm conditions. For example, an instance of the alarmValue object might be named alarmValue.8 |
| 1.3.6.1.4.1.171.10.75.14.22.4.1.1.1 | ColumnrmonAlarmIndex | read-only | current | An index that uniquely identifies an entry in the alarm table. Each such entry defines a diagnostic sample at a particular interval for an object on the device. |
| 1.3.6.1.4.1.171.10.75.14.22.4.1.1.2 | ColumnrmonAlarmInterval | read-create | current | The interval in seconds over which the data is sampled and compared with the rising and falling thresholds. When setting this variable, care should be taken in… |
| 1.3.6.1.4.1.171.10.75.14.22.4.1.1.3 | ColumnrmonAlarmVariable | read-create | current | The object identifier of the particular variable to be sampled. Only variables that resolve to an ASN.1 primitive type of INTEGER (INTEGER, Integer32, Counter3… |
| 1.3.6.1.4.1.171.10.75.14.22.4.1.1.4 | ColumnrmonAlarmSampleType | read-create | current | The method of sampling the selected variable and calculating the value to be compared against the thresholds. If the value of this object is absoluteValue(1), … |
| 1.3.6.1.4.1.171.10.75.14.22.4.1.1.5 | ColumnrmonAlarmRisingThreshold | read-create | current | A threshold for the sampled statistic. When the current sampled value is greater than or equal to this threshold, and the value at the last sampling interval w… |
| 1.3.6.1.4.1.171.10.75.14.22.4.1.1.6 | ColumnrmonAlarmFallingThreshold | read-create | current | A threshold for the sampled statistic. When the current sampled value is less than or equal to this threshold, and the value at the last sampling interval was … |
| 1.3.6.1.4.1.171.10.75.14.22.4.1.1.7 | ColumnrmonAlarmRisingEventIndex | read-create | current | The index of the eventEntry that is used when a rising threshold is crossed. The eventEntry identified by a particular value of this index is the same as ident… |
| 1.3.6.1.4.1.171.10.75.14.22.4.1.1.8 | ColumnrmonAlarmFallingEventIndex | read-create | current | The index of the eventEntry that is used when a falling threshold is crossed. The eventEntry identified by a particular value of this index is the same as iden… |
| 1.3.6.1.4.1.171.10.75.14.22.4.1.1.9 | ColumnrmonAlarmOwner | read-create | current | The entity that configured this entry and is therefore using the resources assigned to it. |
| 1.3.6.1.4.1.171.10.75.14.22.4.1.1.10 | ColumnrmonAlarmStatus | read-create | current | The status of this alarm entry. |
| 1.3.6.1.4.1.171.10.75.14.22.5 | NodermonEvent | |||
| 1.3.6.1.4.1.171.10.75.14.22.5.1 | TablermonEventTable | not-accessible | current | A list of events to be generated. |
| 1.3.6.1.4.1.171.10.75.14.22.5.1.1 | RowrmonEventEntry | not-accessible | current | A set of parameters that describe an event to be generated when certain conditions are met. As an example, an instance of the eventLastTimeSent object might be… |
| 1.3.6.1.4.1.171.10.75.14.22.5.1.1.1 | ColumnrmonEventIndex | read-only | current | An index that uniquely identifies an entry in the event table. Each such entry defines one event that is to be generated when the appropriate conditions occur. |
| 1.3.6.1.4.1.171.10.75.14.22.5.1.1.2 | ColumnrmonEventDescription | read-create | current | A comment describing this event entry. |
| 1.3.6.1.4.1.171.10.75.14.22.5.1.1.3 | ColumnrmonEventType | read-create | current | The type of notification that the probe will make about this event. In the case of log, an entry is made in the log table for each event. In the case of snmp-t… |
| 1.3.6.1.4.1.171.10.75.14.22.5.1.1.4 | ColumnrmonEventCommunity | read-create | current | If an SNMP trap is to be sent, it will be sent to the SNMP community specified by this octet string. |
| 1.3.6.1.4.1.171.10.75.14.22.5.1.1.5 | ColumnrmonEventOwner | read-create | current | The entity that configured this entry and is therefore using the resources assigned to it. If this object contains a string starting with 'monitor' and has ass… |
| 1.3.6.1.4.1.171.10.75.14.22.5.1.1.6 | ColumnrmonEventStatus | read-create | current | The status of this event entry. If this object is not equal to valid(1), all associated log entries shall be deleted by the agent. |
| 1.3.6.1.4.1.171.10.75.14.23 | NodecompanyAuthGroup | |||
| 1.3.6.1.4.1.171.10.75.14.23 | NodeimpbMacBlocked | Storm Occurred. | ||
| 1.3.6.1.4.1.171.10.75.14.23.1 | NodeswAuthenCtrl | |||
| 1.3.6.1.4.1.171.10.75.14.23.1.1 | ScalarswAuthStatus | read-write | current | Enable/Disable Static 802.1x. |
| 1.3.6.1.4.1.171.10.75.14.23.1.2 | ScalarswAuthMode | read-write | current | This object indicates the authentication mode of the device. |
| 1.3.6.1.4.1.171.10.75.14.23.1.3 | ScalarauthProtocol | read-write | current | The authentication method used to authenticate users. |
| 1.3.6.1.4.1.171.10.75.14.23.2 | NodeswAuthPortAccessCtrl | |||
| 1.3.6.1.4.1.171.10.75.14.23.2.1 | TableswAuthPortAccessControlTable | not-accessible | current | A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may auth… |
| 1.3.6.1.4.1.171.10.75.14.23.2.1.1 | RowswAuthPortAccessControlEntry | not-accessible | current | The configuration information for an Authenticator Port. |
| 1.3.6.1.4.1.171.10.75.14.23.2.1.1.1 | ColumnswAuthAuthConfigPortNumber | read-only | current | A unique value for each port that correlates to port index. Its value ranges between 1 and the value of port number. |
| 1.3.6.1.4.1.171.10.75.14.23.2.1.1.2 | ColumnswAuthAuthQuietPeriod | read-write | current | The value, in seconds, of the quietPeriod constant currently in use by the Authenticator PAE state machine. |
| 1.3.6.1.4.1.171.10.75.14.23.2.1.1.3 | ColumnswAuthAuthSuppTimeout | read-write | current | The value, in seconds, of the suppTimeout constant currently in use by the Backend Authentication state machine. |
| 1.3.6.1.4.1.171.10.75.14.23.2.1.1.4 | ColumnswAuthAuthServerTimeout | read-write | current | The value, in seconds, of the serverTimeout constant currently in use by the Backend Authentication state machine. |
| 1.3.6.1.4.1.171.10.75.14.23.2.1.1.5 | ColumnswAuthAuthMaxReq | read-write | current | The value of the maxReq constant currently in use by the Backend Authentication state machine. |
| 1.3.6.1.4.1.171.10.75.14.23.2.1.1.6 | ColumnswAuthAuthTxPeriod | read-write | current | The value, in seconds, of the txPeriod constant currently in use by the Authenticator PAE state machine. |
| 1.3.6.1.4.1.171.10.75.14.23.2.1.1.7 | ColumnswAuthAuthReAuthPeriod | read-write | current | The value, in seconds, of the reAuthPeriod constant currently in use by the Reauthentication Timer state machine. |
| 1.3.6.1.4.1.171.10.75.14.23.2.1.1.8 | ColumnswAuthAuthReAuthentication | read-write | current | The enable/disable control used by the Reauthentication Timer state machine (8.5.5.1). |
| 1.3.6.1.4.1.171.10.75.14.23.2.1.1.9 | ColumnswAuthAuthConfigPortControl | read-write | current | The current value of the controlled Port control parameter for the Port. |
| 1.3.6.1.4.1.171.10.75.14.23.2.1.1.10 | ColumnswAuthAuthCapability | read-write | current | The current value of the controlled Port control parameter for the Port. |
| 1.3.6.1.4.1.171.10.75.14.23.2.1.1.11 | ColumnswAuthAuthDirection | read-write | current | The current value of the controlled Port control parameter for the Port. |
| 1.3.6.1.4.1.171.10.75.14.23.3 | NodeswAuthUser | |||
| 1.3.6.1.4.1.171.10.75.14.23.3.1 | TableswAuthUserTable | not-accessible | current | A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may auth… |
| 1.3.6.1.4.1.171.10.75.14.23.3.1.1 | RowswAuthUserEntry | not-accessible | current | The configuration information for an Authenticator Port. |
| 1.3.6.1.4.1.171.10.75.14.23.3.1.1.1 | ColumnswAuthUserName | read-only | current | The unique index value of a row in this table. This object is used to set 802.1X Local user name, The following characters are allowed to input: semicolon, que… |
| 1.3.6.1.4.1.171.10.75.14.23.3.1.1.2 | ColumnswAuthUserPassword | read-write | current | This object is used to set 802.1X Local user Password, The following characters are allowed to input: semicolon, question mark, space, and double quotation mar… |
| 1.3.6.1.4.1.171.10.75.14.23.3.1.1.3 | ColumnswAuthUserStatus | read-create | current | The status of this conceptual row in the swAuthUserTable. An entry in this table is not qualified for activation until instances of all corresponding columns h… |
| 1.3.6.1.4.1.171.10.75.14.23.4 | NodeswAuthRadiusServer | |||
| 1.3.6.1.4.1.171.10.75.14.23.4.1 | TableswAuthRadiusServerTable | not-accessible | current | A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may auth… |
| 1.3.6.1.4.1.171.10.75.14.23.4.1.1 | RowswAuthRadiusServerEntry | not-accessible | current | The configuration information for an Authenticator Port. |
| 1.3.6.1.4.1.171.10.75.14.23.4.1.1.1 | ColumnswAuthRadiusServerIndex | read-only | current | A unique value for Authentication RADIUS Server index. Its value ranges between 1 and 3. |
| 1.3.6.1.4.1.171.10.75.14.23.4.1.1.2 | ColumnswAuthRadiusServerAddress | read-write | current | The IP address of the RADIUS server referred to in this table entry. |
| 1.3.6.1.4.1.171.10.75.14.23.4.1.1.3 | ColumnswAuthRadiusServerAuthenticationPort | read-write | current | The value is for setting UDP Port. |
| 1.3.6.1.4.1.171.10.75.14.23.4.1.1.4 | ColumnswAuthRadiusServerAccountingPort | read-write | current | The value is for setting UDP Port. |
| 1.3.6.1.4.1.171.10.75.14.23.4.1.1.5 | ColumnswAuthRadiusServerTimeout | read-write | current | The value is for setting UDP Port. |
| 1.3.6.1.4.1.171.10.75.14.23.4.1.1.6 | ColumnswAuthRadiusServerRetransmit | read-write | current | The value is for setting UDP Port. |
| 1.3.6.1.4.1.171.10.75.14.23.4.1.1.7 | ColumnswAuthRadiusServerKey | read-write | current | This object is used to set 802.1X Radius Server Key, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark. |
| 1.3.6.1.4.1.171.10.75.14.23.4.1.1.8 | ColumnswAuthRadiusServerStatus | read-create | current | The status of this conceptual row in the swAuthRadiusServerTable. An entry in this table is not qualified for activation until instances of all corresponding c… |
| 1.3.6.1.4.1.171.10.75.14.24 | NodecompanyGuestVlan | |||
| 1.3.6.1.4.1.171.10.75.14.24.1 | ScalarguestVlanName | read-write | current | The VLAN name of guest VLAN. |
| 1.3.6.1.4.1.171.10.75.14.24.2 | ScalarguestVlanPort | read-write | current | This object indicates the guest VLAN port members of this device. |
| 1.3.6.1.4.1.171.10.75.14.24.3 | ScalarguestVlanDelState | read-write | current | Used to delete the guest VLAN. |
| 1.3.6.1.4.1.171.10.75.14.25 | NodecompanyMacNotify | |||
| 1.3.6.1.4.1.171.10.75.14.25.1 | ScalarmacNotifyState | read-write | current | This object can enabled or disabled MAC Notification. |
| 1.3.6.1.4.1.171.10.75.14.25.2 | ScalarmacNotifyInterval | read-write | current | This object indicates the time interval in second for trigger the MAC notify message. |
| 1.3.6.1.4.1.171.10.75.14.25.3 | ScalarmacNotifyHistorySize | read-write | current | This object indicates the history size of variation MAC in address table. The default value is 1 . |
| 1.3.6.1.4.1.171.10.75.14.25.4 | TablemacNotifyCtrlTable | not-accessible | current | A table to control Loopback detection features either for the entire switch or for each interface in the switch. |
| 1.3.6.1.4.1.171.10.75.14.25.4.1 | RowmacNotifyCtrlEntry | not-accessible | current | An entry appears in this table for each interface in the system. |
| 1.3.6.1.4.1.171.10.75.14.25.4.1.1 | ColumnmacNotifyCtrlIndex | read-only | current | The interface index of the port for which the configuration in this entry applies. |
| 1.3.6.1.4.1.171.10.75.14.25.4.1.2 | ColumnmacNotifyPortStatus | read-write | current | Provides control to per port enable or disable the loopback detection function. Default is disabled. |
| 1.3.6.1.4.1.171.10.75.14.26 | NodecompanySMTP | |||
| 1.3.6.1.4.1.171.10.75.14.26.1 | ScalarsmtpState | read-write | current | Enable or Disable SMTP function. |
| 1.3.6.1.4.1.171.10.75.14.26.2 | ScalarsmtpServerAddr | read-write | current | SMTP Server's IP Address |
| 1.3.6.1.4.1.171.10.75.14.26.3 | ScalarsmtpServerPort | read-write | current | SMTP Server's port |
| 1.3.6.1.4.1.171.10.75.14.26.4 | ScalarsmtpSelfMailAddr | read-write | current | The sender's (DUT) mail address . |
| 1.3.6.1.4.1.171.10.75.14.26.5 | TablesmtpRecvMailAddrTable | not-accessible | current | Receivers' mail address table. |
| 1.3.6.1.4.1.171.10.75.14.26.5.1 | RowsmtpRecvMailAddrEntry | not-accessible | current | Receivers' mail address entry. |
| 1.3.6.1.4.1.171.10.75.14.26.5.1.1 | ColumnsmtpRecvMailAddrIndex | read-only | current | Receivers' mail address index (1~8). |
| 1.3.6.1.4.1.171.10.75.14.26.5.1.2 | ColumnsmtpRecvMailAddr | read-write | current | Receivers' mail address. |
| 1.3.6.1.4.1.171.10.75.14.26.5.1.3 | ColumnsmtpRecvMailAddrStatus | read-write | current | Rowstatus of the receiver's mail address. |
| 1.3.6.1.4.1.171.10.75.14.27 | NodecompanyISMVLAN | |||
| 1.3.6.1.4.1.171.10.75.14.27.1 | ScalarigmpMulticastVlanStatus | read-write | current | Enable/Disable IGMP Multicast Vlan function. |
| 1.3.6.1.4.1.171.10.75.14.27.2 | TableigmpMulticastVlanTable | not-accessible | current | Information about the IGMP snooping multicast VLAN table. |
| 1.3.6.1.4.1.171.10.75.14.27.2.1 | RowigmpMulticastVlanEntry | not-accessible | current | The entry of igmpMulticastVlanTable. |
| 1.3.6.1.4.1.171.10.75.14.27.2.1.1 | ColumnigmpMulticastVlanid | read-only | current | This object indicates the VLAN ID of the IGMP snooping multicast VLAN entry. |
| 1.3.6.1.4.1.171.10.75.14.27.2.1.2 | ColumnigmpMulticastVlanName | read-create | current | This object indicates the VLAN name of the IGMP snooping multicast VLAN entry. |
| 1.3.6.1.4.1.171.10.75.14.27.2.1.3 | ColumnigmpMulticastVlanSourcePort | read-write | current | This object indicates the port list of the source ports of the IGMP snooping multicast VLAN. The source ports will be set as tag ports of the VLAN entry and th… |
| 1.3.6.1.4.1.171.10.75.14.27.2.1.4 | ColumnigmpMulticastVlanMemberPort | read-write | current | This object indicates the port list of the member ports of the IGMP snooping multicast VLAN. The source ports will be set as untagged ports of the VLAN entry a… |
| 1.3.6.1.4.1.171.10.75.14.27.2.1.5 | ColumnigmpMulticastVlanTagMemberPort | read-write | current | This object indicates the port list of the tag member ports of the IGMP snooping multicast VLAN. |
| 1.3.6.1.4.1.171.10.75.14.27.2.1.6 | ColumnigmpMulticastVlanState | read-write | current | This object can be used to enable or disable the IGMP snooping multicast VLAN. |
| 1.3.6.1.4.1.171.10.75.14.27.2.1.7 | ColumnigmpMulticastVlanReplaceSourceIp | read-write | current | The replacement source IP of this multicast VLAN. |
| 1.3.6.1.4.1.171.10.75.14.27.2.1.8 | ColumnigmpMulticastVlanRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.10.75.14.27.3 | TableigmpMulticastVlanGroupTable | not-accessible | current | The table containing the IGMP snooping multicast VLAN group information |
| 1.3.6.1.4.1.171.10.75.14.27.3.1 | RowigmpMulticastVlanGroupEntry | not-accessible | current | Information about the current IGMP snooping multicast VLAN group. |
| 1.3.6.1.4.1.171.10.75.14.27.3.1.1 | ColumnigmpMulticastVlanGroupVid | read-only | current | This object indicates the VID of the IGMP snooping multicast VLAN group. |
| 1.3.6.1.4.1.171.10.75.14.27.3.1.2 | ColumnigmpMulticastVlanGroupFromIp | read-only | current | Specifies the multicast address list for this VLAN. |
| 1.3.6.1.4.1.171.10.75.14.27.3.1.3 | ColumnigmpMulticastVlanGroupToIp | read-only | current | Specifies the multicast address list for this VLAN. |
| 1.3.6.1.4.1.171.10.75.14.27.3.1.4 | ColumnigmpMulticastVlanGroupStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.10.75.14.28 | NodecompanyDHCPRelay | |||
| 1.3.6.1.4.1.171.10.75.14.28.1 | NodedhcpBOOTPRelayControl | |||
| 1.3.6.1.4.1.171.10.75.14.28.1.1 | ScalardhcpBOOTPRelayState | read-write | current | This object indicates DHCP relay function is enabled or disabled. |
| 1.3.6.1.4.1.171.10.75.14.28.1.2 | ScalardhcpBOOTPRelayHopCount | read-write | current | This object indicates the maximum number of router hops that the BOOTP packets can cross. |
| 1.3.6.1.4.1.171.10.75.14.28.1.3 | ScalardhcpBOOTPRelayTimeThreshold | read-write | current | This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP … |
| 1.3.6.1.4.1.171.10.75.14.28.2 | NodedhcpBOOTPRelayManagement | |||
| 1.3.6.1.4.1.171.10.75.14.28.2.1 | TabledhcpBOOTPRelayInterfaceSettingsTable | not-accessible | current | This table indicates the IP address as a destination to forward (relay) DHCP packets to. |
| 1.3.6.1.4.1.171.10.75.14.28.2.1.1 | RowdhcpBOOTPRelayInterfaceSettingsEntry | not-accessible | current | A list of information indicates the IP address as a destination to forward (relay) DHCP packets to. |
| 1.3.6.1.4.1.171.10.75.14.28.2.1.1.1 | ColumndhcpBOOTPRelayInterface | read-only | current | This object indicates the name of the IP interface. |
| 1.3.6.1.4.1.171.10.75.14.28.2.1.1.2 | ColumndhcpBOOTPRelayServerIP | read-only | current | This object indicates the DHCP server IP address. |
| 1.3.6.1.4.1.171.10.75.14.28.2.1.1.3 | ColumndhcpBOOTPRelayInterfaceSettingsRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.10.75.14.28.2.2 | NodedhcpBOOTPRelayManagementOption82 | |||
| 1.3.6.1.4.1.171.10.75.14.28.2.2.1 | ScalardhcpBOOTPRelayOption82State | read-write | current | This object indicates DHCP relay option 82 function is enabled or disabled. |
| 1.3.6.1.4.1.171.10.75.14.28.2.2.2 | ScalardhcpBOOTPRelayOption82CheckState | read-write | current | This object indicates DHCP relay option 82 Check function is enabled or disabled. |
| 1.3.6.1.4.1.171.10.75.14.28.2.2.3 | ScalardhcpBOOTPRelayOption82Policy | read-write | current | This object indicates DHCP relay option 82 policy. |
| 1.3.6.1.4.1.171.10.75.14.28.2.2.4 | ScalardhcpBOOTPRelayOption82RemoteIDType | read-write | current | This object indicates the type of remote ID. If the type is default, the remote ID will be the MAC address of the device, otherwise, the remote ID can be defin… |
| 1.3.6.1.4.1.171.10.75.14.28.2.2.5 | ScalardhcpBOOTPRelayOption82RemoteID | read-write | current | This object displays the current remote ID of the device. If swDHCPRelayOption82RemoteIDType is set to default, the value will be the MAC address of the device… |
| 1.3.6.1.4.1.171.10.75.14.29 | NodecompanyDHCPLocalRelay | |||
| 1.3.6.1.4.1.171.10.75.14.29.1 | ScalardhcpLocalRelayGlobalState | read-write | current | This object indicates DHCP local relay function of VLAN is enabled or disabled. |
| 1.3.6.1.4.1.171.10.75.14.29.2 | TabledhcpLocalRelayTable | not-accessible | current | This table indicates the IP address as a destination to forward (local relay) DHCP packets to. |
| 1.3.6.1.4.1.171.10.75.14.29.2.1 | RowdhcpLocalRelayTableEntry | not-accessible | current | A list of information indicates the IP address as a destination to forward (local relay) DHCP packets to. |
| 1.3.6.1.4.1.171.10.75.14.29.2.1.1 | ColumndhcpLocalRelaySettingsVLANID | read-only | current | This object displays the current VLAN ID of the device. |
| 1.3.6.1.4.1.171.10.75.14.29.2.1.2 | ColumndhcpLocalRelaySettingsState | read-write | current | This object indicates DHCP local relay function of VLAN is enabled or disabled. |
| 1.3.6.1.4.1.171.10.75.14.30 | NodecompanyTrapSetting | |||
| 1.3.6.1.4.1.171.10.75.14.30.1 | ScalarsysTrapIP | read-write | current | The smart console utility's IP address is used to recive trap events. |
| 1.3.6.1.4.1.171.10.75.14.30.2 | ScalarsysTrapSystemEvent | read-write | current | Enable/Disable system trap events in the switch system. |
| 1.3.6.1.4.1.171.10.75.14.30.3 | ScalarsysTrapFiberPortEvent | read-write | current | Enable/Disable fiber port trap event in the system. |
| 1.3.6.1.4.1.171.10.75.14.30.4 | ScalarsysTrapTwistedPortEvent | read-write | current | Enable/Disable twisted port trap event in the system. |
| 1.3.6.1.4.1.171.10.75.14.30.5 | ScalarsysTrapStateChangeEvent | read-write | current | Enable/Disable RSTP state change trap event in the system. |
| 1.3.6.1.4.1.171.10.75.14.30.6 | ScalarsysTrapFirmUpgradeEvent | read-write | current | Enable/Disable firmware upgrading trap event in the system. |
| 1.3.6.1.4.1.171.10.75.14.30.10 | ScalarsysTrapStatus | read-write | current | Enable/Disable trap event in the system. |
| 1.3.6.1.4.1.171.10.75.14.32 | NodecompanyLLDPSetting | |||
| 1.3.6.1.4.1.171.10.75.14.32.1 | ScalardlinklldpState | read-write | current | This object is used for enabling or disabling LLDP in the system. |
| 1.3.6.1.4.1.171.10.75.14.32.2 | ScalardlinklldpMsgHoldMultiplier | read-write | current | The time-to-live value expressed as a multiple of the lldpMessageTxInterval object.The actual time-to-live value used in LLDP frames, transmitted on behalf of … |
| 1.3.6.1.4.1.171.10.75.14.32.3 | ScalardlinklldpMsgTxInterval | read-write | current | This object is used for LLDP packet update frequency. The timer in units of seconds. |
| 1.3.6.1.4.1.171.10.75.14.32.4 | ScalardlinklldpReinitDelay | read-write | current | This object is used for LLDP Reinitialization Delay. The timer in units of seconds. |
| 1.3.6.1.4.1.171.10.75.14.32.5 | ScalardlinklldpTxDelay | read-write | current | The lldpTxDelay indicates the delay (in units of seconds) between successive LLDP frame transmissions initiated by value/status changes in the LLDP local syste… |
| 1.3.6.1.4.1.171.10.75.14.32.6 | ScalardlinklldpConfigManAddrPortsTxEnable | read-write | current | A set of ports that are identified by a PortList, in which each port is represented as a bit. The corresponding local system management address instance will b… |
| 1.3.6.1.4.1.171.10.75.14.32.11 | TablelldpPortConfigTable | not-accessible | current | The table that controls LLDP frame transmission on individual ports. |
| 1.3.6.1.4.1.171.10.75.14.32.11.1 | RowlldpPortConfigEntry | not-accessible | current | LLDP configuration information for a particular port. This configuration parameter controls the transmission and the reception of LLDP frames on those ports wh… |
| 1.3.6.1.4.1.171.10.75.14.32.11.1.1 | ColumnlldpPortConfigPortNum | not-accessible | current | The index value used to identify the port component (contained in the local chassis with the LLDP agent) associated with this entry. The value of this object i… |
| 1.3.6.1.4.1.171.10.75.14.32.11.1.2 | ColumnlldpPortConfigAdminStatus | read-write | current | The administratively desired status of the local LLDP agent. If the associated lldpPortConfigAdminStatus object has a value of 'txOnly(1)', then LLDP agent wil… |
| 1.3.6.1.4.1.171.10.75.14.32.11.1.3 | ColumnlldpPortConfigNotificationEnable | read-write | current | The lldpPortConfigNotificationEnable controls, on a per port basis, whether or not notifications from the agent are enabled. The value true(1) means that notif… |
| 1.3.6.1.4.1.171.10.75.14.32.11.1.4 | ColumnlldpPortConfigTLVsTxEnable | read-write | current | The lldpPortConfigTLVsTxEnable, defined as a bitmap, includes the basic set of LLDP TLVs whose transmission is allowed on the local LLDP agent by the network m… |
| 1.3.6.1.4.1.171.10.75.14.32.12 | NodelldpXdot3Objects | |||
| 1.3.6.1.4.1.171.10.75.14.32.12.1 | NodelldpXdot3Config | |||
| 1.3.6.1.4.1.171.10.75.14.32.12.1.1 | TablelldpXdot3PortConfigTable | not-accessible | current | A table that controls selection of LLDP TLVs to be transmitted on individual ports. |
| 1.3.6.1.4.1.171.10.75.14.32.12.1.1.1 | RowlldpXdot3PortConfigEntry | not-accessible | current | LLDP configuration information that controls the transmission of IEEE 802.3 organizationally defined TLVs on LLDP transmission capable ports. This configuratio… |
| 1.3.6.1.4.1.171.10.75.14.32.12.1.1.1.1 | ColumnlldpXdot3PortConfigTLVsTxEnable | read-write | current | The lldpXdot3PortConfigTLVsTxEnable, defined as a bitmap, includes the IEEE 802.3 organizationally defined set of LLDP TLVs whose transmission is allowed on th… |
| 1.3.6.1.4.1.171.10.75.14.32.12.2 | NodelldpXdot3LocalData | |||
| 1.3.6.1.4.1.171.10.75.14.32.12.2.1 | TablelldpXdot3LocPortTable | not-accessible | current | This table contains one row per port of Ethernet port information (as a part of the LLDP 802.3 organizational extension) on the local system known to this agen… |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.1.1 | RowlldpXdot3LocPortEntry | not-accessible | current | Information about a particular port component. |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.1.1.1 | ColumnlldpXdot3LocPortAutoNegSupported | read-only | current | The truth value used to indicate whether the given port (associated with the local system) supports Auto-negotiation. |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.1.1.2 | ColumnlldpXdot3LocPortAutoNegEnabled | read-only | current | The truth value used to indicate whether port Auto-negotiation is enabled on the given port associated with the local system. |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.1.1.3 | ColumnlldpXdot3LocPortAutoNegAdvertisedCap | read-only | current | This object contains the value (bitmap) of the ifMauAutoNegCapAdvertisedBits object (defined in IETF RFC 3636) which is associated with the given port on the l… |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.1.1.4 | ColumnlldpXdot3LocPortOperMauType | read-only | current | An integer value that indicates the operational MAU type of the given port on the local system. This object contains the integer value derived from the list po… |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.2 | TablelldpXdot3LocPowerTable | not-accessible | current | This table contains one row per port of power ethernet information (as a part of the LLDP 802.3 organizational extension) on the local system known to this age… |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.2.1 | RowlldpXdot3LocPowerEntry | not-accessible | current | Information about a particular port component. |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.2.1.1 | ColumnlldpXdot3LocPowerPortClass | read-only | current | The value that identifies the port Class of the given port associated with the local system. |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.2.1.2 | ColumnlldpXdot3LocPowerMDISupported | read-only | current | The truth value used to indicate whether the MDI power is supported on the given port associated with the local system. |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.2.1.3 | ColumnlldpXdot3LocPowerMDIEnabled | read-only | current | The truth value used to identify whether MDI power is enabled on the given port associated with the local system. |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.2.1.4 | ColumnlldpXdot3LocPowerPairControlable | read-only | current | The truth value is derived from the value of pethPsePortPowerPairsControlAbility object (defined in IETF RFC 3621) and is used to indicate whether the pair sel… |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.2.1.5 | ColumnlldpXdot3LocPowerPairs | read-only | current | This object contains the value of the pethPsePortPowerPairs object (defined in IETF RFC 3621) which is associated with the given port on the local system. |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.2.1.6 | ColumnlldpXdot3LocPowerClass | read-only | current | This object contains the value of the pethPsePortPowerClassifications object (defined in IETF RFC 3621) which is associated with the given port on the local sy… |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.3 | TablelldpXdot3LocLinkAggTable | not-accessible | current | This table contains one row per port of link aggregation information (as a part of the LLDP 802.3 organizational extension) on the local system known to this a… |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.3.1 | RowlldpXdot3LocLinkAggEntry | not-accessible | current | Link Aggregation information about a particular port component. |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.3.1.1 | ColumnlldpXdot3LocLinkAggStatus | read-only | current | The bitmap value contains the link aggregation capabilities and the current aggregation status of the link. |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.3.1.2 | ColumnlldpXdot3LocLinkAggPortId | read-only | current | This object contains the IEEE 802.3 aggregated port identifier, aAggPortID (IEEE 802.3-2002, 30.7.2.1.1), derived from the ifNumber of the ifIndex for the port… |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.4 | TablelldpXdot3LocMaxFrameSizeTable | not-accessible | current | This table contains one row per port of maximum frame size information (as a part of the LLDP 802.3 organizational extension) on the local system known to this… |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.4.1 | RowlldpXdot3LocMaxFrameSizeEntry | not-accessible | current | Maximum Frame Size information about a particular port component. |
| 1.3.6.1.4.1.171.10.75.14.32.12.2.4.1.1 | ColumnlldpXdot3LocMaxFrameSize | read-only | current | An integer value indicating the maximum supported frame size in octets on the given port of the local system. |
| 1.3.6.1.4.1.171.10.75.14.32.12.3 | NodelldpXdot3RemoteData | |||
| 1.3.6.1.4.1.171.10.75.14.32.12.3.1 | TablelldpXdot3RemPortTable | not-accessible | current | This table contains Ethernet port information (as a part of the LLDP 802.3 organizational extension) of the remote system. |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.1.1 | RowlldpXdot3RemPortEntry | not-accessible | current | Information about a particular physical network connection. |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.1.1.1 | ColumnlldpXdot3RemPortAutoNegSupported | read-only | current | The truth value used to indicate whether the given port (associated with remote system) supports Auto-negotiation. |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.1.1.2 | ColumnlldpXdot3RemPortAutoNegEnabled | read-only | current | The truth value used to indicate whether port Auto-negotiation is enabled on the given port associated with the remote system. |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.1.1.3 | ColumnlldpXdot3RemPortAutoNegAdvertisedCap | read-only | current | This object contains the value (bitmap) of the ifMauAutoNegCapAdvertisedBits object (defined in IETF RFC 3636) which is associated with the given port on the r… |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.1.1.4 | ColumnlldpXdot3RemPortOperMauType | read-only | current | An integer value that indicates the operational MAU type of the sending device. This object contains the integer value derived from the list position of the co… |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.2 | TablelldpXdot3RemPowerTable | not-accessible | current | This table contains Ethernet power information (as a part of the LLDP 802.3 organizational extension) of the remote system. |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.2.1 | RowlldpXdot3RemPowerEntry | not-accessible | current | Information about a particular physical network connection. |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.2.1.1 | ColumnlldpXdot3RemPowerPortClass | read-only | current | The value that identifies the port Class of the given port associated with the remote system. |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.2.1.2 | ColumnlldpXdot3RemPowerMDISupported | read-only | current | The truth value used to indicate whether the MDI power is supported on the given port associated with the remote system. |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.2.1.3 | ColumnlldpXdot3RemPowerMDIEnabled | read-only | current | The truth value used to identify whether MDI power is enabled on the given port associated with the remote system. |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.2.1.4 | ColumnlldpXdot3RemPowerPairControlable | read-only | current | The truth value is derived from the value of pethPsePortPowerPairsControlAbility object (defined in IETF RFC 3621) and is used to indicate whether the pair sel… |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.2.1.5 | ColumnlldpXdot3RemPowerPairs | read-only | current | This object contains the value of the pethPsePortPowerPairs object (defined in IETF RFC 3621) which is associated with the given port on the remote system. |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.2.1.6 | ColumnlldpXdot3RemPowerClass | read-only | current | This object contains the value of the pethPsePortPowerClassifications object (defined in IETF RFC 3621) which is associated with the given port on the remote s… |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.3 | TablelldpXdot3RemLinkAggTable | not-accessible | current | This table contains port link aggregation information (as a part of the LLDP 802.3 organizational extension) of the remote system. |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.3.1 | RowlldpXdot3RemLinkAggEntry | not-accessible | current | Link Aggregation information about remote system's port component. |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.3.1.1 | ColumnlldpXdot3RemLinkAggStatus | read-only | current | The bitmap value contains the link aggregation capabilities and the current aggregation status of the link. |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.3.1.2 | ColumnlldpXdot3RemLinkAggPortId | read-only | current | This object contains the IEEE 802.3 aggregated port identifier, aAggPortID (IEEE 802.3-2002, 30.7.2.1.1), derived from the ifNumber of the ifIndex for the port… |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.4 | TablelldpXdot3RemMaxFrameSizeTable | not-accessible | current | This table contains one row per port of maximum frame size information (as a part of the LLDP 802.3 organizational extension) of the remote system. |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.4.1 | RowlldpXdot3RemMaxFrameSizeEntry | not-accessible | current | Maximum Frame Size information about a particular port component. |
| 1.3.6.1.4.1.171.10.75.14.32.12.3.4.1.1 | ColumnlldpXdot3RemMaxFrameSize | read-only | current | An integer value indicating the maximum supported frame size in octets on the port component associated with the remote system. |
| 1.3.6.1.4.1.171.10.75.14.32.13 | NodelldpXdot1Objects | |||
| 1.3.6.1.4.1.171.10.75.14.32.13.1 | NodelldpXdot1Config | |||
| 1.3.6.1.4.1.171.10.75.14.32.13.1.1 | TablelldpXdot1ConfigPortVlanTable | not-accessible | current | A table that controls selection of LLDP Port VLAN-ID TLVs to be transmitted on individual ports. |
| 1.3.6.1.4.1.171.10.75.14.32.13.1.1.1 | RowlldpXdot1ConfigPortVlanEntry | not-accessible | current | LLDP configuration information that controls the transmission of IEEE 802.1 organizationally defined Port VLAN-ID TLV on LLDP transmission capable ports. This … |
| 1.3.6.1.4.1.171.10.75.14.32.13.1.1.1.1 | ColumnlldpXdot1ConfigPortVlanTxEnable | read-write | current | The lldpXdot1ConfigPortVlanTxEnable, which is defined as a truth value and configured by the network management, determines whether the IEEE 802.1 organization… |
| 1.3.6.1.4.1.171.10.75.14.32.13.1.2 | TablelldpXdot1ConfigVlanNameTable | not-accessible | current | The table that controls selection of LLDP VLAN name TLV instances to be transmitted on individual ports. |
| 1.3.6.1.4.1.171.10.75.14.32.13.1.2.1 | RowlldpXdot1ConfigVlanNameEntry | not-accessible | current | LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System VLAN name instance will be transmitted. Th… |
| 1.3.6.1.4.1.171.10.75.14.32.13.1.2.1.1 | ColumnlldpXdot1ConfigVlanNameTxEnable | read-write | current | The boolean value that indicates whether the corresponding Local System VLAN name instance will be transmitted on the port defined by the given lldpXdot1LocVla… |
| 1.3.6.1.4.1.171.10.75.14.32.13.1.3 | TablelldpXdot1ConfigProtoVlanTable | not-accessible | current | The table that controls selection of LLDP Port and Protocol VLAN ID TLV instances to be transmitted on individual ports. |
| 1.3.6.1.4.1.171.10.75.14.32.13.1.3.1 | RowlldpXdot1ConfigProtoVlanEntry | not-accessible | current | LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System Protocol VLAN instance will be transmitted… |
| 1.3.6.1.4.1.171.10.75.14.32.13.1.3.1.1 | ColumnlldpXdot1ConfigProtoVlanTxEnable | read-write | current | The boolean value that indicates whether the corresponding Local System Port and Protocol VLAN instance will be transmitted on the port defined by the given ll… |
| 1.3.6.1.4.1.171.10.75.14.32.13.1.4 | TablelldpXdot1ConfigProtocolTable | not-accessible | current | The table that controls selection of LLDP Protocol TLV instances to be transmitted on individual ports. |
| 1.3.6.1.4.1.171.10.75.14.32.13.1.4.1 | RowlldpXdot1ConfigProtocolEntry | not-accessible | current | LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System Protocol instance will be transmitted. Thi… |
| 1.3.6.1.4.1.171.10.75.14.32.13.1.4.1.1 | ColumnlldpXdot1ConfigProtocolTxEnable | read-write | current | The boolean value that indicates whether the corresponding Local System Protocol Identity instance will be transmitted on the port defined by the given lldpXdo… |
| 1.3.6.1.4.1.171.10.75.14.32.13.2 | NodelldpXdot1LocalData | |||
| 1.3.6.1.4.1.171.10.75.14.32.13.2.1 | TablelldpXdot1LocTable | not-accessible | current | This table contains one row per port for IEEE 802.1 organizationally defined LLDP extension on the local system known to this agent. |
| 1.3.6.1.4.1.171.10.75.14.32.13.2.1.1 | RowlldpXdot1LocEntry | not-accessible | current | Information about IEEE 802.1 organizationally defined LLDP extension. |
| 1.3.6.1.4.1.171.10.75.14.32.13.2.1.1.1 | ColumnlldpXdot1LocPortVlanId | read-only | current | The integer value used to identify the port's VLAN identifier associated with the local system. A value of zero shall be used if the system either does not kno… |
| 1.3.6.1.4.1.171.10.75.14.32.13.2.2 | TablelldpXdot1LocProtoVlanTable | not-accessible | current | This table contains one or more rows per Port and Protocol VLAN information about the local system. |
| 1.3.6.1.4.1.171.10.75.14.32.13.2.2.1 | RowlldpXdot1LocProtoVlanEntry | not-accessible | current | Port and protocol VLAN ID Information about a particular port component. There may be multiple port and protocol VLANs, identified by a particular lldpXdot1Loc… |
| 1.3.6.1.4.1.171.10.75.14.32.13.2.2.1.1 | ColumnlldpXdot1LocProtoVlanId | not-accessible | current | The integer value used to identify the port and protocol VLANs associated with the given port associated with the local system. A value of zero shall be used i… |
| 1.3.6.1.4.1.171.10.75.14.32.13.2.2.1.2 | ColumnlldpXdot1LocProtoVlanSupported | read-only | current | The truth value used to indicate whether the given port (associated with the local system) supports port and protocol VLANs. |
| 1.3.6.1.4.1.171.10.75.14.32.13.2.2.1.3 | ColumnlldpXdot1LocProtoVlanEnabled | read-only | current | The truth value used to indicate whether the port and protocol VLANs are enabled on the given port associated with the local system. |
| 1.3.6.1.4.1.171.10.75.14.32.13.2.3 | TablelldpXdot1LocVlanNameTable | not-accessible | current | This table contains one or more rows per IEEE 802.1Q VLAN name information on the local system known to this agent. |
| 1.3.6.1.4.1.171.10.75.14.32.13.2.3.1 | RowlldpXdot1LocVlanNameEntry | not-accessible | current | VLAN name Information about a particular port component. There may be multiple VLANs, identified by a particular lldpXdot1LocVlanId, configured on the given po… |
| 1.3.6.1.4.1.171.10.75.14.32.13.2.3.1.1 | ColumnlldpXdot1LocVlanId | not-accessible | current | The integer value used to identify the IEEE 802.1Q VLAN IDs with which the given port is compatible. |
| 1.3.6.1.4.1.171.10.75.14.32.13.2.3.1.2 | ColumnlldpXdot1LocVlanName | read-only | current | The string value used to identify VLAN name identified by the Vlan Id associated with the given port on the local system. This object should contain the value … |
| 1.3.6.1.4.1.171.10.75.14.32.13.2.4 | TablelldpXdot1LocProtocolTable | not-accessible | current | This table contains one or more rows per protocol identity information on the local system known to this agent. |
| 1.3.6.1.4.1.171.10.75.14.32.13.2.4.1 | RowlldpXdot1LocProtocolEntry | not-accessible | current | Information about particular protocols that are accessible through the given port component. There may be multiple protocols, identified by particular lldpXdot… |
| 1.3.6.1.4.1.171.10.75.14.32.13.2.4.1.1 | ColumnlldpXdot1LocProtocolIndex | not-accessible | current | This object represents an arbitrary local integer value used by this agent to identify a particular protocol identity. |
| 1.3.6.1.4.1.171.10.75.14.32.13.2.4.1.2 | ColumnlldpXdot1LocProtocolId | read-only | current | The octet string value used to identify the protocols associated with the given port of the local system. |
| 1.3.6.1.4.1.171.10.75.14.32.13.3 | NodelldpXdot1RemoteData | |||
| 1.3.6.1.4.1.171.10.75.14.32.13.3.1 | TablelldpXdot1RemTable | not-accessible | current | This table contains one or more rows per physical network connection known to this agent. The agent may wish to ensure that only one lldpXdot1RemEntry is prese… |
| 1.3.6.1.4.1.171.10.75.14.32.13.3.1.1 | RowlldpXdot1RemEntry | not-accessible | current | Information about a particular port component. |
| 1.3.6.1.4.1.171.10.75.14.32.13.3.1.1.1 | ColumnlldpXdot1RemPortVlanId | read-only | current | The integer value used to identify the port's VLAN identifier associated with the remote system. if the remote system either does not know the PVID or does not… |
| 1.3.6.1.4.1.171.10.75.14.32.13.3.2 | TablelldpXdot1RemProtoVlanTable | not-accessible | current | This table contains one or more rows per Port and Protocol VLAN information about the remote system, received on the given port. |
| 1.3.6.1.4.1.171.10.75.14.32.13.3.2.1 | RowlldpXdot1RemProtoVlanEntry | not-accessible | current | Port and protocol VLAN name Information about a particular port component. There may be multiple protocol VLANs, identified by a particular lldpXdot1RemProtoVl… |
| 1.3.6.1.4.1.171.10.75.14.32.13.3.2.1.1 | ColumnlldpXdot1RemProtoVlanId | not-accessible | current | The integer value used to identify the port and protocol VLANs associated with the given port associated with the remote system. If port and protocol VLANs are… |
| 1.3.6.1.4.1.171.10.75.14.32.13.3.2.1.2 | ColumnlldpXdot1RemProtoVlanSupported | read-only | current | The truth value used to indicate whether the given port (associated with the remote system) is capable of supporting port and protocol VLANs. |
| 1.3.6.1.4.1.171.10.75.14.32.13.3.2.1.3 | ColumnlldpXdot1RemProtoVlanEnabled | read-only | current | The truth value used to indicate whether the port and protocol VLANs are enabled on the given port associated with the remote system. |
| 1.3.6.1.4.1.171.10.75.14.32.13.3.3 | TablelldpXdot1RemVlanNameTable | not-accessible | current | This table contains one or more rows per IEEE 802.1Q VLAN name information about the remote system, received on the given port. |
| 1.3.6.1.4.1.171.10.75.14.32.13.3.3.1 | RowlldpXdot1RemVlanNameEntry | not-accessible | current | VLAN name Information about a particular port component. There may be multiple VLANs, identified by a particular lldpXdot1RemVlanId, received on the given port. |
| 1.3.6.1.4.1.171.10.75.14.32.13.3.3.1.1 | ColumnlldpXdot1RemVlanId | not-accessible | current | The integer value used to identify the IEEE 802.1Q VLAN IDs with which the given port of the remote system is compatible. |
| 1.3.6.1.4.1.171.10.75.14.32.13.3.3.1.2 | ColumnlldpXdot1RemVlanName | read-only | current | The string value used to identify VLAN name identified by the VLAN Id associated with the remote system. |
| 1.3.6.1.4.1.171.10.75.14.32.13.3.4 | TablelldpXdot1RemProtocolTable | not-accessible | current | This table contains one or more rows per protocol information about the remote system, received on the given port. |
| 1.3.6.1.4.1.171.10.75.14.32.13.3.4.1 | RowlldpXdot1RemProtocolEntry | not-accessible | current | Protocol information about a particular port component. There may be multiple protocols, identified by a particular lldpXdot1ProtocolIndex, received on the giv… |
| 1.3.6.1.4.1.171.10.75.14.32.13.3.4.1.1 | ColumnlldpXdot1RemProtocolIndex | not-accessible | current | This object represents an arbitrary local integer value used by this agent to identify a particular protocol identity. |
| 1.3.6.1.4.1.171.10.75.14.32.13.3.4.1.2 | ColumnlldpXdot1RemProtocolId | read-only | current | The octet string value used to identify the protocols associated with the given port of remote system. |
| 1.3.6.1.4.1.171.10.75.14.33 | NodecompanyCPUInterfaceFilterGroup | |||
| 1.3.6.1.4.1.171.10.75.14.33.1 | NodecpuFilterProfile | |||
| 1.3.6.1.4.1.171.10.75.14.33.1.1 | TablecpuFilterProfileTable | not-accessible | current | A table to CPUInterfaceFilter profile . |
| 1.3.6.1.4.1.171.10.75.14.33.1.1.1 | RowcpuFilterProfileEntry | not-accessible | current | Each entry in this table is a CPUInterfaceFilter profile. Index to the table is CPUInterfaceFilter profile ID. |
| 1.3.6.1.4.1.171.10.75.14.33.1.1.1.1 | ColumncpuFilterProfileNo | read-only | current | The CPUInterfaceFilter Profile ID. The ID 1 to 50 is user-defined CPUInterfaceFilter, and the ID more than 50 is reserved for system-defined CPUInterfaceFilter… |
| 1.3.6.1.4.1.171.10.75.14.33.1.1.1.2 | ColumncpuFilterProfileType | read-write | current | The CPUInterfaceFilter Profile type, possible value are l2 (1) - for MAC-based rule, l3 (2) - for IPv4-based rule, |
| 1.3.6.1.4.1.171.10.75.14.33.1.1.1.3 | ColumncpuFilterProfileRuleCount | read-only | current | The number of rules in this profile. |
| 1.3.6.1.4.1.171.10.75.14.33.1.1.1.4 | ColumncpuFilterProfileMask | read-write | current | Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT L2 DST-MAC 0 (LSB) L2 SRC-MAC 1 L2 VID … |
| 1.3.6.1.4.1.171.10.75.14.33.1.1.1.5 | ColumncpuFilterProfileDstMacAddrMask | read-write | current | The CPUInterfaceFilter Profile destination MAC address mask. If DST-MAC is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL2… |
| 1.3.6.1.4.1.171.10.75.14.33.1.1.1.6 | ColumncpuFilterProfileSrcMacAddrMask | read-write | current | The CPUInterfaceFilter Profile source MAC address mask. If SRC-MAC is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL2RuleS… |
| 1.3.6.1.4.1.171.10.75.14.33.1.1.1.7 | ColumncpuFilterProfileIPProtocol | read-write | current | Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none. |
| 1.3.6.1.4.1.171.10.75.14.33.1.1.1.8 | ColumncpuFilterProfileIPProtocolMask | read-write | current | The CPUInterfaceFilter Profile IP protocol mask. If cpuFilterProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule fie… |
| 1.3.6.1.4.1.171.10.75.14.33.1.1.1.9 | ColumncpuFilterProfileDstIpAddrMask | read-write | current | The CPUInterfaceFilter Profile destination IP address mask. If DST-IP is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3Ru… |
| 1.3.6.1.4.1.171.10.75.14.33.1.1.1.10 | ColumncpuFilterProfileSrcIpAddrMask | read-write | current | The CPUInterfaceFilter Profile source IP address mask. If SRC-IP is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleSrc… |
| 1.3.6.1.4.1.171.10.75.14.33.1.1.1.11 | ColumncpuFilterProfileDstPortMask | read-write | current | The CPUInterfaceFilter Profile UDP/TCP destination port mask. If DST-PORT is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilter… |
| 1.3.6.1.4.1.171.10.75.14.33.1.1.1.12 | ColumncpuFilterProfileSrcPortMask | read-write | current | The CPUInterfaceFilter Profile UDP/TCP source port mask. If SRC-PORT is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3Rul… |
| 1.3.6.1.4.1.171.10.75.14.33.1.1.1.15 | ColumncpuFilterProfileStatus | read-create | current | This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait… |
| 1.3.6.1.4.1.171.10.75.14.33.2 | NodecpuFilterL2Rule | |||
| 1.3.6.1.4.1.171.10.75.14.33.2.1 | TablecpuFilterL2RuleTable | not-accessible | current | A table to configure L2 filter rules in the system. |
| 1.3.6.1.4.1.171.10.75.14.33.2.1.1 | RowcpuFilterL2RuleEntry | not-accessible | current | Each entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID. |
| 1.3.6.1.4.1.171.10.75.14.33.2.1.1.1 | ColumncpuFilterL2ProfileID | read-only | current | L2 Filter rule ID. |
| 1.3.6.1.4.1.171.10.75.14.33.2.1.1.2 | ColumncpuFilterL2AccessID | read-only | current | CPUInterfaceFilter Profile ID which this rule join. |
| 1.3.6.1.4.1.171.10.75.14.33.2.1.1.3 | ColumncpuFilterL2RuleEtherType | read-write | current | The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '-1', which means the rule don't ca… |
| 1.3.6.1.4.1.171.10.75.14.33.2.1.1.4 | ColumncpuFilterL2RuleDstMacAddr | read-write | current | Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero,which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.33.2.1.1.5 | ColumncpuFilterL2RuleSrcMacAddr | read-write | current | Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero, which means the rule don't care this condition.. address |
| 1.3.6.1.4.1.171.10.75.14.33.2.1.1.6 | ColumncpuFilterL2RuleVlanId | read-write | current | Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule… |
| 1.3.6.1.4.1.171.10.75.14.33.2.1.1.7 | ColumncpuFilterL2Rule1pPriority | read-write | current | 802.1p priority to be matched with the packet. By Default, the value will be '-1', which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.33.2.1.1.8 | ColumncpuFilterL2RuleDstMacAddrMask | read-only | current | The MAC address Mask work for Destination MAC address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.75.14.33.2.1.1.9 | ColumncpuFilterL2RuleSrcMacAddrMask | read-only | current | The MAC address Mask work for Source MAC address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.75.14.33.2.1.1.10 | ColumncpuFilterL2RuleInPortList | read-write | current | Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list. |
| 1.3.6.1.4.1.171.10.75.14.33.2.1.1.11 | ColumncpuFilterL2RuleAction | read-write | current | Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding r… |
| 1.3.6.1.4.1.171.10.75.14.33.2.1.1.14 | ColumncpuFilterL2RuleStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.75.14.33.3 | NodecpuFilterL3Rule | |||
| 1.3.6.1.4.1.171.10.75.14.33.3.1 | TablecpuFilterL3RuleTable | not-accessible | current | A table to configure L3 filter rules in the system. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1 | RowcpuFilterL3RuleEntry | not-accessible | current | Each entry in this table is a L3 filter rule. Index to the table is L3 filter number and Profile ID. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.1 | ColumncpuFilterL3RuleProfileNo | read-only | current | L3 Filter rule ID. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.2 | ColumncpuFilterL3RuleAccessID | read-only | current | The Profile ID which this rule join. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.3 | ColumncpuFilterL3RuleProtocol | read-write | current | The type of protocol to be checked against the packet. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.4 | ColumncpuFilterL3RuleProtocolMask | read-only | current | The IP protocol mask. This field is read-only and copy from it's Profile setting. It will work with the other field,cpuFilterL3RuleProtocol, to caculate a rang… |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.5 | ColumncpuFilterL3RuleICMPMessageType | read-write | current | The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action s… |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.6 | ColumncpuFilterL3RuleICMPMessageCode | read-write | current | The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action s… |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.7 | ColumncpuFilterL3RuleDstIpAddr | read-write | current | Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.8 | ColumncpuFilterL3RuleSrcIpAddr | read-write | current | Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.9 | ColumncpuFilterL3RuleDstIpAddrMask | read-only | current | The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.10 | ColumncpuFilterL3RuleSrcIpAddrMask | read-only | current | The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.11 | ColumncpuFilterL3RuleTcpUdpDstPort | read-write | current | The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.12 | ColumncpuFilterL3RuleTcpUdpSrcPort | read-write | current | The TCP / UDP source port. The default value is -1, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.13 | ColumncpuFilterL3RuleTcpUdpDstPortMask | read-only | current | The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.14 | ColumncpuFilterL3RuleTcpUdpSrcPortMask | read-only | current | The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.15 | ColumncpuFilterL3RuleTcpAckBit | read-create | current | The TCP ACK bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.16 | ColumncpuFilterL3RuleTcpRstBit | read-create | current | The TCP RST bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.17 | ColumncpuFilterL3RuleTcpUrgBit | read-create | current | The TCP Urg bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.18 | ColumncpuFilterL3RuleTcpPshBit | read-create | current | The TCP Psh bit to be checked against the packet. The default value is 'dontcare'(-1). which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.19 | ColumncpuFilterL3RuleTcpSynBit | read-create | current | The TCP Syn bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.20 | ColumncpuFilterL3RuleTcpFinBit | read-create | current | The TCP Fin bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.21 | ColumncpuFilterL3RuleDscp | read-create | current | The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.22 | ColumncpuFilterL3RuleIgmpType | read-write | current | The IGMP Type to be checked against the packet.A default value is '-1', which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.23 | ColumncpuFilterL3RulePortList | read-write | current | Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.24 | ColumncpuFilterL3RuleAction | read-write | current | Specifies the action to be taken on the packet if the filter rule matches. |
| 1.3.6.1.4.1.171.10.75.14.33.3.1.1.27 | ColumncpuFilterL3RuleStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.75.14.34 | NodecompanyAutoSurveillanceVlan | |||
| 1.3.6.1.4.1.171.10.75.14.34.1 | NodeautoSurveillanceVlanSystem | |||
| 1.3.6.1.4.1.171.10.75.14.34.1.1 | ScalarautoSurveillanceVlanMode | read-write | current | This object is for enabling or disabling Auto Surveillance Vlan function in the system. If the Vlan mode is in Asymmetric VLAN mode, Auto Surveillance VLAN can… |
| 1.3.6.1.4.1.171.10.75.14.34.1.2 | ScalarautoSurveillanceVlanId | read-write | current | The ID of VLAN that you want the surveillance traffic to be in. It must be a exist vlan id. |
| 1.3.6.1.4.1.171.10.75.14.34.1.3 | ScalarautoSurveillanceVlanPriority | read-write | current | The 802.1p priority levels of the traffic in the Auto Surveillance VLAN. |
| 1.3.6.1.4.1.171.10.75.14.34.1.4 | ScalarautoSurveillanceVlanTaggedUplinkDownlinkPort | read-write | current | Auto Surveillance vlan uplink ports can't auto learning OUI. |
| 1.3.6.1.4.1.171.10.75.14.34.2 | NodeautoSurveillanceVlanOUI | |||
| 1.3.6.1.4.1.171.10.75.14.34.2.1 | TableautoSurveillanceVlanOUITable | not-accessible | current | A Auto Surveillance vlan OUI entry containing the description and mac. |
| 1.3.6.1.4.1.171.10.75.14.34.2.1.1 | RowautoSurveillanceVlanOUIEntry | not-accessible | current | A Auto Surveillance vlan OUI entry containing the description and mac. |
| 1.3.6.1.4.1.171.10.75.14.34.2.1.1.1 | ColumnautoSurveillanceVlanOUISurveillanceOUI | read-only | current | An Organizationally Unique Identifier (OUI) is a 24-bit number that is purchased from the IEEE Registration Authority. This identifier uniquely identifies a ve… |
| 1.3.6.1.4.1.171.10.75.14.34.2.1.1.2 | ColumnautoSurveillanceVlanOUIDescription | read-write | current | The Description for the OUI. |
| 1.3.6.1.4.1.171.10.75.14.34.2.1.1.3 | ColumnautoSurveillanceVlanOUIMask | read-write | current | Auto Surveillance vlan OUI Mask. The default OUI Mask is FF:FF:FF:F0:00:00. And default OUI Mask is read-only. In user define OUI's Mask is FF:FF:FF:00:00:00, … |
| 1.3.6.1.4.1.171.10.75.14.34.2.1.1.4 | ColumnautoSurveillanceVlanOUIComponentType | read-write | current | This object indicates the Component Type of this entry. To create a new entry, you must set the autoSurveillanceVlanOUIComponentType to be CreateAndGo, then th… |
| 1.3.6.1.4.1.171.10.75.14.34.2.1.1.5 | ColumnautoSurveillanceVlanOUIStatus | read-write | current | This object indicates the status of this entry. To create a new entry, you must set the autoSurveillanceVlanOUIStatus to be CreateAndGo, then this entry will t… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| BridgeId | OCTET STRING (SIZE (8)) | current | The Bridge-Identifier as used in the Spanning Tree Protocol to uniquely identify a bridge. Its first two octets (in network byte order) contain a priority value and its last 6 octets contain the MAC address used to refe… |
| LacpKey | Integer32 (0..65535) | current | The Actor or Partner Key value (0..65535). |
| LldpLinkAggStatusMap | BITS { aggCapable(0), aggEnabled(1) } | current | This TC describes the link aggregation status. The bit 'aggCapable(0)' indicates the link is capable of being aggregated. The bit 'aggEnabled(1)' indicates the link is currently in aggregation. |
| LldpPortNumber | Integer32(1..4096) | current | Each port contained in the chassis (that is known to the LLDP agent) is uniquely identified by a port number. A port number has no mandatory relationship to an InterfaceIndex object (of the interfaces MIB, IETF RFC 2863… |
| LldpPowerPortClass | INTEGER { pClassPSE(1), pClassPD(2) } | current | This TC describes the Power over Ethernet (PoE) port class. |
| OwnerString | OCTET STRING (SIZE (0..127)) | current | This data type is used to model an administratively assigned name of the owner of a resource. Implementations must accept values composed of well-formed NVT ASCII sequences. In addition, implementations should accept va… |
| PortLaMode | INTEGER { lacp(1), static(2), disable(3) } | current | Defines how a Port Channel does channeling. lacp(1) - place the port into passive negotiation state, in which the port waits for its peer to initiate negotiation. static(2) - force the port to enable channeling. disable… |
| PortList | OCTET STRING | current | Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents… |
| RmonStatus | INTEGER { valid(1), createRequest(2), underCreation(3), invalid(4) } | current | The status of a table entry. Setting this object to the value invalid(4) has the effect of invalidating the corresponding entry. That is, it effectively disassociates the mapping identified with said entry. It is an imp… |
| Timeout | INTEGER | current | A STP timer in units of 1/100 seconds To convert a Timeout value into a value in units of 1/256 seconds, the following algorithm should be used: b = floor( (n * 256) / 100) where: floor = quotient [ignore remainder] n i… |
| VlanIndex | Unsigned32 | current | A value used to index per-VLAN tables: values of 0 and 4095 are not permitted; if the value is between 1 and 4094 inclusive, it represents an IEEE 802.1Q VLAN-ID with global scope within a given bridged domain (see Vlan… |