DES6500-SWL2MGMT-MIB
137 objects
The Structure of Layer 2 Network Management Information for the D-Link enterprise.
Imported Objects
| BRIDGE-MIB | dot1dBridge dot1dStp dot1dStpPortEntry |
| DLINK-ID-REC-MIB | AgentNotifyLevel |
| Q-BRIDGE-MIB | --PortList |
| SNMPv2-SMI | Integer32 IpAddress MODULE-IDENTITY OBJECT-TYPE TimeTicks |
| SNMPv2-TC | DisplayString RowStatus TruthValue |
| SW6500PRIMGMT-MIB | des6500 |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.171.11.78.1.2 | IdentityswL2MgmtMIB | The Structure of Layer 2 Network Management Information for the D-Link enterprise. | ||
| 1.3.6.1.4.1.171.11.78.1.2.1 | NodeswL2DevMgmt | |||
| 1.3.6.1.4.1.171.11.78.1.2.1.1 | NodeswL2DevInfo | |||
| 1.3.6.1.4.1.171.11.78.1.2.1.1.1 | ScalarswDevInfoTotalNumOfPort | read-only | current | The number of ports within this switch. This value is the sum of the ports within this switch. |
| 1.3.6.1.4.1.171.11.78.1.2.1.1.2 | ScalarswDevInfoNumOfPortInUse | read-only | current | The number of ports in this switch connected to the segment or the end stations. |
| 1.3.6.1.4.1.171.11.78.1.2.1.1.3 | ScalarswDevInfoBootPromVersion | read-only | current | Boot Prom Version. |
| 1.3.6.1.4.1.171.11.78.1.2.1.1.4 | ScalarswDevInfoFirmwareVersion | read-only | current | Firmware Version. |
| 1.3.6.1.4.1.171.11.78.1.2.1.1.5 | ScalarswDevInfoHardwareVersion | read-only | current | Hardware Version. |
| 1.3.6.1.4.1.171.11.78.1.2.1.2 | NodeswL2DevCtrl | |||
| 1.3.6.1.4.1.171.11.78.1.2.1.2.1 | ScalarswL2DevCtrlStpState | read-write | current | This object can be enabled or disabled spanning tree algorithm during runtime of the system. |
| 1.3.6.1.4.1.171.11.78.1.2.1.2.2 | ScalarswL2DevCtrlIGMPSnooping | read-write | current | This object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled. |
| 1.3.6.1.4.1.171.11.78.1.2.1.2.3 | ScalarswL2DevCtrlIGMPSnoopingMcstRTOnly | read-write | current | |
| 1.3.6.1.4.1.171.11.78.1.2.1.2.4 | ScalarswL2DevCtrlRmonState | read-write | current | This object can be enabled or disabled RMON. |
| 1.3.6.1.4.1.171.11.78.1.2.1.2.5 | ScalarswL2DevCtrlCleanAllStatisticCounter | read-write | current | As the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing. |
| 1.3.6.1.4.1.171.11.78.1.2.1.2.6 | ScalarswL2DevCtrlVlanIdOfFDBTbl | read-write | current | Indicates the VLAN ID which the Dot1dTpFdbTable belongs to ; The default value is DEFAULT_VLAN_ID of system . |
| 1.3.6.1.4.1.171.11.78.1.2.1.2.14 | NodeswL2DevCtrlWeb | |||
| 1.3.6.1.4.1.171.11.78.1.2.1.2.14.1 | ScalarswL2DevCtrlWebState | read-write | current | This object control web status. |
| 1.3.6.1.4.1.171.11.78.1.2.1.2.14.2 | ScalarswL2DevCtrlWebTcpPort | read-write | current | This object can designate tcp port. When web disable this object can't accessible. |
| 1.3.6.1.4.1.171.11.78.1.2.1.2.15 | NodeswL2DevCtrlTelnet | |||
| 1.3.6.1.4.1.171.11.78.1.2.1.2.15.1 | ScalarswL2DevCtrlTelnetState | read-write | current | This object control telnet status. |
| 1.3.6.1.4.1.171.11.78.1.2.1.2.15.2 | ScalarswL2DevCtrlTelnetTcpPort | read-write | current | This object can designate tcp port. When telnet disable this object can't accessible. |
| 1.3.6.1.4.1.171.11.78.1.2.1.3 | NodeswL2DevAlarm | |||
| 1.3.6.1.4.1.171.11.78.1.2.1.3.1 | ScalarswL2DevAlarmNewRoot | read-write | current | When the device has become the new root of the Spanning Tree, this object decide whether to send a new root trap. |
| 1.3.6.1.4.1.171.11.78.1.2.1.3.2 | ScalarswL2DevAlarmTopologyChange | read-write | current | This object determine to send a trap or not when the switch topology was changed. If the object is enabled(3), the topologyChange trap is sent by the device wh… |
| 1.3.6.1.4.1.171.11.78.1.2.1.3.3 | ScalarswL2DevAlarmLinkChange | read-write | current | This object determine to send a trap or not when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its … |
| 1.3.6.1.4.1.171.11.78.1.2.3 | NodeswL2PortMgmt | |||
| 1.3.6.1.4.1.171.11.78.1.2.3.1 | TableswL2PortInfoTable | not-accessible | current | A table that contains information about every port. |
| 1.3.6.1.4.1.171.11.78.1.2.3.1.1 | RowswL2PortInfoEntry | not-accessible | current | A list of information for each port of the device. |
| 1.3.6.1.4.1.171.11.78.1.2.3.1.1.1 | ColumnswL2PortInfoPortIndex | read-only | current | This object indicates the module's port number.(1..Max port number in the module) |
| 1.3.6.1.4.1.171.11.78.1.2.3.1.1.2 | ColumnswL2PortInfoPortNumber | read-only | current | This object indicates the module's port number. |
| 1.3.6.1.4.1.171.11.78.1.2.3.1.1.3 | ColumnswL2PortInfoUnitID | read-only | current | Indicates ID of the unit in the system |
| 1.3.6.1.4.1.171.11.78.1.2.3.1.1.4 | ColumnswL2PortInfoType | read-only | current | This object indicates the connector type of this port. |
| 1.3.6.1.4.1.171.11.78.1.2.3.1.1.5 | ColumnswL2PortInfoLinkStatus | read-only | current | This object indicates the port link status. |
| 1.3.6.1.4.1.171.11.78.1.2.3.1.1.6 | ColumnswL2PortInfoNwayStatus | read-only | current | This object indicates the port speed and duplex mode. |
| 1.3.6.1.4.1.171.11.78.1.2.3.2 | TableswL2PortCtrlTable | not-accessible | current | A table that contains control information about every port. |
| 1.3.6.1.4.1.171.11.78.1.2.3.2.1 | RowswL2PortCtrlEntry | not-accessible | current | A list of control information for each port of the device. |
| 1.3.6.1.4.1.171.11.78.1.2.3.2.1.1 | ColumnswL2PortCtrlPortIndex | read-only | current | This object indicates the module's port number.(1..Max port number in the module) |
| 1.3.6.1.4.1.171.11.78.1.2.3.2.1.2 | ColumnswL2PortCtrlUnitIndex | read-only | current | Indicates ID of the unit in the device |
| 1.3.6.1.4.1.171.11.78.1.2.3.2.1.3 | ColumnswL2PortCtrlAdminState | read-write | current | This object decide the port enabled or disabled. |
| 1.3.6.1.4.1.171.11.78.1.2.3.2.1.4 | ColumnswL2PortCtrlNwayState | read-write | current | Chose the port speed, duplex mode, and N-Way function mode. |
| 1.3.6.1.4.1.171.11.78.1.2.3.2.1.5 | ColumnswL2PortCtrlFlowCtrlState | read-write | current | The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mo… |
| 1.3.6.1.4.1.171.11.78.1.2.3.2.1.6 | ColumnswL2PortCtrlLockState | read-write | current | This object decide the port is locked or not. |
| 1.3.6.1.4.1.171.11.78.1.2.3.3 | ScalarswL2PortCtrlJumboFrame | read-write | current | This object configure the switch's jumbo frame settings. |
| 1.3.6.1.4.1.171.11.78.1.2.6 | NodeswL2QOSMgmt | |||
| 1.3.6.1.4.1.171.11.78.1.2.6.1 | TableswL2QOSBandwidthControlTable | not-accessible | current | . |
| 1.3.6.1.4.1.171.11.78.1.2.6.1.1 | RowswL2QOSBandwidthControlEntry | not-accessible | current | A list of information contained in swL2QOSBandwidthControlTable. |
| 1.3.6.1.4.1.171.11.78.1.2.6.1.1.1 | ColumnswL2QOSBandwidthPortIndex | read-only | current | Indicates the port . |
| 1.3.6.1.4.1.171.11.78.1.2.6.1.1.2 | ColumnswL2QOSBandwidthRxRate | read-write | current | Indicates RX Rate(Mbit/sec) of the specifed port. Value 1000 means no limit. Value 10000 means no limit for 10G port. |
| 1.3.6.1.4.1.171.11.78.1.2.6.1.1.3 | ColumnswL2QOSBandwidthTxRate | read-write | current | Indicates TX Rate(Mbit/sec) of the specifed port. Value 1000 means no limit. Value 10000 means no limit for 10G port. |
| 1.3.6.1.4.1.171.11.78.1.2.6.2 | TableswL2QOSSchedulingTable | not-accessible | current | . |
| 1.3.6.1.4.1.171.11.78.1.2.6.2.1 | RowswL2QOSSchedulingEntry | not-accessible | current | A list of information contained in swL2QOSSchedulingTable. |
| 1.3.6.1.4.1.171.11.78.1.2.6.2.1.1 | ColumnswL2QOSSchedulingClassIndex | read-only | current | Indicates the hardware queue number. |
| 1.3.6.1.4.1.171.11.78.1.2.6.2.1.2 | ColumnswL2QOSSchedulingMaxPkts | read-write | current | Indicates the maximum number of packets the hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its … |
| 1.3.6.1.4.1.171.11.78.1.2.6.2.1.3 | ColumnswL2QOSSchedulingMechanism | read-only | current | Indicates the mechanism of QOS scheduling. |
| 1.3.6.1.4.1.171.11.78.1.2.6.3 | TableswL2QOS8021pUserPriorityTable | not-accessible | current | . |
| 1.3.6.1.4.1.171.11.78.1.2.6.3.1 | RowswL2QOS8021pUserPriorityEntry | not-accessible | current | A list of information contained in swL2QOS8021pUserPriorityTable. |
| 1.3.6.1.4.1.171.11.78.1.2.6.3.1.1 | ColumnswL2QOS8021pUserPriorityIndex | read-only | current | The 802.1p user priority . |
| 1.3.6.1.4.1.171.11.78.1.2.6.3.1.2 | ColumnswL2QOS8021pUserPriorityClass | read-write | current | The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) a… |
| 1.3.6.1.4.1.171.11.78.1.2.6.4 | TableswL2QOS8021pDefaultPriorityTable | not-accessible | current | . |
| 1.3.6.1.4.1.171.11.78.1.2.6.4.1 | RowswL2QOS8021pDefaultPriorityEntry | not-accessible | current | A list of information contained in swL2QOS8021pDefaultPriorityTable. |
| 1.3.6.1.4.1.171.11.78.1.2.6.4.1.1 | ColumnswL2QOS8021pDefaultPriorityIndex | read-only | current | Indicates the port number . |
| 1.3.6.1.4.1.171.11.78.1.2.6.4.1.2 | ColumnswL2QOS8021pDefaultPriority | read-write | current | The priority value to assign to untagged packets received by the switch ports on the switch.. |
| 1.3.6.1.4.1.171.11.78.1.2.6.5 | ScalarswL2QOSSchedulingMechanismCtrl | read-write | current | This object can control QOS scheduling Mechanism. |
| 1.3.6.1.4.1.171.11.78.1.2.6.6 | ScalarswL2QOSHolPreventionCtrl | read-write | current | Control QOS Hol Prevention |
| 1.3.6.1.4.1.171.11.78.1.2.7 | NodeswL2PortSecurityMgmt | |||
| 1.3.6.1.4.1.171.11.78.1.2.7.1 | TableswL2PortSecurityControlTable | not-accessible | current | port security feature which controls the address leaning capability and the traffic forwarding decision. Each port can have this function enabled or disabled. … |
| 1.3.6.1.4.1.171.11.78.1.2.7.1.1 | RowswL2PortSecurityControlEntry | not-accessible | current | A list of information contained in swL2PortSecurityControlTable. |
| 1.3.6.1.4.1.171.11.78.1.2.7.1.1.1 | ColumnswL2PortSecurityPortIndex | read-only | current | Indicates the secured port to lock address learning. |
| 1.3.6.1.4.1.171.11.78.1.2.7.1.1.2 | ColumnswL2PortSecurityMaxLernAddr | read-write | current | Indicates allowable number of addresses to be learned at this port. |
| 1.3.6.1.4.1.171.11.78.1.2.7.1.1.3 | ColumnswL2PortSecurityMode | read-write | current | Indicates the mode of locking address. In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer expire. In this mode, when the locke… |
| 1.3.6.1.4.1.171.11.78.1.2.7.1.1.4 | ColumnswL2PortSecurityAdmState | read-write | current | Indicates administration state of locking address. |
| 1.3.6.1.4.1.171.11.78.1.2.7.2 | NodeswL2PortSecurityDelCtrl | |||
| 1.3.6.1.4.1.171.11.78.1.2.7.2.1 | ScalarswL2PortSecurityDelVlanName | read-write | current | Indicates vlan name. |
| 1.3.6.1.4.1.171.11.78.1.2.7.2.2 | ScalarswL2PortSecurityDelPort | read-write | current | Indicates the port. |
| 1.3.6.1.4.1.171.11.78.1.2.7.2.3 | ScalarswL2PortSecurityDelMacAddress | read-write | current | Specifies MAC address. |
| 1.3.6.1.4.1.171.11.78.1.2.7.2.4 | ScalarswL2PortSecurityDelActivity | read-write | current | . |
| 1.3.6.1.4.1.171.11.78.1.2.9 | NodeswL2TrunkMgmt | |||
| 1.3.6.1.4.1.171.11.78.1.2.9.1 | ScalarswL2TrunkMaxSupportedEntries | read-only | current | Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable). |
| 1.3.6.1.4.1.171.11.78.1.2.9.2 | ScalarswL2TrunkCurrentNumEntries | read-only | current | Current actived number of entries in the trunk configuration table. |
| 1.3.6.1.4.1.171.11.78.1.2.9.3 | TableswL2TrunkCtrlTable | not-accessible | current | This table specifys which ports group a set of ports(up to 8) into a single logical link. |
| 1.3.6.1.4.1.171.11.78.1.2.9.3.1 | RowswL2TrunkCtrlEntry | not-accessible | current | A list of information specifies which ports group a set of ports(up to 8) into a single logical link. |
| 1.3.6.1.4.1.171.11.78.1.2.9.3.1.1 | ColumnswL2TrunkIndex | read-only | current | The index of logical port trunk. The trunk group number depend on the existence of unit and module. |
| 1.3.6.1.4.1.171.11.78.1.2.9.3.1.2 | ColumnswL2TrunkName | read-create | current | The name of logical port trunk. |
| 1.3.6.1.4.1.171.11.78.1.2.9.3.1.3 | ColumnswL2TrunkMasterPort | read-create | current | The object indicates the master port number of the port trunk entry. When using Port Trunk, you can not configure the other ports of the group except the maste… |
| 1.3.6.1.4.1.171.11.78.1.2.9.3.1.4 | ColumnswL2TrunkMember | read-create | current | Indicate how many number of ports is included in this Trunk. The trunk port number depend on the existence of module. The maximum number of ports is 8 for one … |
| 1.3.6.1.4.1.171.11.78.1.2.9.3.1.5 | ColumnswL2TrunkFloodingPort | read-only | current | The object indicates the flooding port number of the port trunk entry. The first port of the trunk is implicitly configured to be the flooding port. |
| 1.3.6.1.4.1.171.11.78.1.2.9.3.1.6 | ColumnswL2TrunkType | read-create | current | This object indicated that type of the trunk group. static : is static trunk group lacp : is LACP trunk group . |
| 1.3.6.1.4.1.171.11.78.1.2.9.3.1.7 | ColumnswL2TrunkState | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.11.78.1.2.9.4 | ScalarswL2TrunkAlgorithm | read-write | current | This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data. |
| 1.3.6.1.4.1.171.11.78.1.2.9.5 | TableswL2TrunkLACPPortTable | not-accessible | current | This table specifys which ports group a set of ports(up to 8) into a single logical link. |
| 1.3.6.1.4.1.171.11.78.1.2.9.5.1 | RowswL2TrunkLACPPortEntry | not-accessible | current | A list of information specifies which ports group a set of ports(up to 8) into a single logical link. |
| 1.3.6.1.4.1.171.11.78.1.2.9.5.1.1 | ColumnswL2TrunkLACPPortIndex | read-only | current | The index of logical port lacp. |
| 1.3.6.1.4.1.171.11.78.1.2.9.5.1.2 | ColumnswL2TrunkLACPPortState | read-write | current | The state of logical port lacp. |
| 1.3.6.1.4.1.171.11.78.1.2.10 | NodeswL2MirrorMgmt | |||
| 1.3.6.1.4.1.171.11.78.1.2.10.1 | ScalarswL2MirrorLogicTargetPort | read-write | current | This object indicates switch which port will sniff another port. A trunk port member cannot be configured as a target Snooping port. The port number is the seq… |
| 1.3.6.1.4.1.171.11.78.1.2.10.2 | ScalarswL2MirrorPortSourceIngress | read-write | current | The represent the ingress into the source port packet to sniffed. |
| 1.3.6.1.4.1.171.11.78.1.2.10.3 | ScalarswL2MirrorPortSourceEgress | read-write | current | The represent the egress from the source port packet to sniffed. |
| 1.3.6.1.4.1.171.11.78.1.2.10.4 | ScalarswL2MirrorPortState | read-write | current | This object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from e… |
| 1.3.6.1.4.1.171.11.78.1.2.11 | NodeswL2IGMPSnoopingMgmt | |||
| 1.3.6.1.4.1.171.11.78.1.2.11.1 | ScalarswL2IGMPSnoopingMaxSupportedVlans | read-only | current | Maximum number of Vlans in the layer 2 IGMP control table (swL2IGMPSnoopingCtrlTable). |
| 1.3.6.1.4.1.171.11.78.1.2.11.2 | ScalarswL2IGMPSnoopingMaxIpGroupNumPerVlan | read-only | current | Maximum number of multicast ip group per Vlan in the layer 2 IGMP information table (swL2IGMPSnoopingQueryInfoTable). |
| 1.3.6.1.4.1.171.11.78.1.2.11.3 | TableswL2IGMPSnoopingCtrlTable | not-accessible | current | The table controls the Vlan's IGMP function. Its scale depends on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled mode, there is only one entry in… |
| 1.3.6.1.4.1.171.11.78.1.2.11.3.1 | RowswL2IGMPSnoopingCtrlEntry | not-accessible | current | The entry in IGMP control table (swL2IGMPSnoopingCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled. |
| 1.3.6.1.4.1.171.11.78.1.2.11.3.1.1 | ColumnswL2IGMPSnoopingCtrlVid | read-only | current | This object indicates the IGMP control entry's VLAN id. If VLAN is disabled, the Vid is always 0 and cannot be changed by management users. If VLAN is in Port-… |
| 1.3.6.1.4.1.171.11.78.1.2.11.3.1.2 | ColumnswL2IGMPSnoopingQueryInterval | read-write | current | The frequency at which IGMP Host-Query packets are transmitted on this switch. |
| 1.3.6.1.4.1.171.11.78.1.2.11.3.1.3 | ColumnswL2IGMPSnoopingMaxResponseTime | read-write | current | The maximum query response time on this switch. |
| 1.3.6.1.4.1.171.11.78.1.2.11.3.1.4 | ColumnswL2IGMPSnoopingRobustness | read-write | current | The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. … |
| 1.3.6.1.4.1.171.11.78.1.2.11.3.1.5 | ColumnswL2IGMPSnoopingLastMemberQueryInterval | read-write | current | The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount o… |
| 1.3.6.1.4.1.171.11.78.1.2.11.3.1.6 | ColumnswL2IGMPSnoopingHostTimeout | read-write | current | The timer value for sending IGMP query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to sen… |
| 1.3.6.1.4.1.171.11.78.1.2.11.3.1.7 | ColumnswL2IGMPSnoopingRouteTimeout | read-write | current | The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages. |
| 1.3.6.1.4.1.171.11.78.1.2.11.3.1.8 | ColumnswL2IGMPSnoopingLeaveTimer | read-write | current | When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeav… |
| 1.3.6.1.4.1.171.11.78.1.2.11.3.1.9 | ColumnswL2IGMPSnoopingQueryState | read-write | current | This object decide the IGMP query enabled or disabled. |
| 1.3.6.1.4.1.171.11.78.1.2.11.3.1.10 | ColumnswL2IGMPSnoopingCurrentState | read-only | current | This object indicates the current IGMP query state. |
| 1.3.6.1.4.1.171.11.78.1.2.11.3.1.11 | ColumnswL2IGMPSnoopingCtrlState | read-write | current | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from e… |
| 1.3.6.1.4.1.171.11.78.1.2.11.4 | TableswL2IGMPSnoopingQueryInfoTable | not-accessible | current | The table contains the number current IGMP query packets which is captured by this device, as well as the IGMP query packets sent by the device. |
| 1.3.6.1.4.1.171.11.78.1.2.11.4.1 | RowswL2IGMPSnoopingQueryInfoEntry | not-accessible | current | Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPSnoopingCtrState of associated VLAN entry are all enabled. |
| 1.3.6.1.4.1.171.11.78.1.2.11.4.1.1 | ColumnswL2IGMPSnoopingInfoVid | read-only | current | This object indicates the Vid of associated IGMP info table entry. It follows swL2IGMPSnoopingCtrlVid in the associated entry of IGMP control table (swL2IGMPSn… |
| 1.3.6.1.4.1.171.11.78.1.2.11.4.1.2 | ColumnswL2IGMPSnoopingInfoQueryCount | read-only | current | This object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis. |
| 1.3.6.1.4.1.171.11.78.1.2.11.4.1.3 | ColumnswL2IGMPSnoopingInfoTxQueryCount | read-only | current | This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to relate… |
| 1.3.6.1.4.1.171.11.78.1.2.11.5 | TableswL2IGMPSnoopingInfoTable | not-accessible | current | The table containing current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN ent… |
| 1.3.6.1.4.1.171.11.78.1.2.11.5.1 | RowswL2IGMPSnoopingInfoEntry | not-accessible | current | Information about current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnoopingSnooping and swL2IGMPSnoopingCtrlState of associ… |
| 1.3.6.1.4.1.171.11.78.1.2.11.5.1.1 | ColumnswL2IGMPSnoopingVid | read-only | current | This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network. |
| 1.3.6.1.4.1.171.11.78.1.2.11.5.1.2 | ColumnswL2IGMPSnoopingGroupIpAddr | read-only | current | This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis. |
| 1.3.6.1.4.1.171.11.78.1.2.11.5.1.3 | ColumnswL2IGMPSnoopingMacAddr | read-only | current | This object is identify mac address which is corresponding to swL2IGMPGroupIpAddr, in per-Vlan basis. |
| 1.3.6.1.4.1.171.11.78.1.2.11.5.1.4 | ColumnswL2IGMPSnoopingPortMap | read-only | current | This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map… |
| 1.3.6.1.4.1.171.11.78.1.2.11.5.1.5 | ColumnswL2IGMPSnoopingIpGroupReportCount | read-only | current | This object indicate how much report packet was receive by our device corresponding with this entry from IGMP function enabled, in per-Vlan basis. |
| 1.3.6.1.4.1.171.11.78.1.2.13 | NodeswL2TrafficMgmt | |||
| 1.3.6.1.4.1.171.11.78.1.2.14 | NodeswL2TrafficSegMgmt | |||
| 1.3.6.1.4.1.171.11.78.1.2.14.1 | TableswL2TrafficSegTable | not-accessible | current | This table specifys the port just can forward traffic to the specific port list. |
| 1.3.6.1.4.1.171.11.78.1.2.14.1.1 | RowswL2TrafficSegEntry | not-accessible | current | A list of information specifies the port with its traffic forward list. |
| 1.3.6.1.4.1.171.11.78.1.2.14.1.1.1 | ColumnswL2TrafficSegPort | read-only | current | The port number of the logical port. |
| 1.3.6.1.4.1.171.11.78.1.2.14.1.1.2 | ColumnswL2TrafficSegForwardPorts | read-write | current | The port list that the specific port can forward traffic. |
| 1.3.6.1.4.1.171.11.78.1.2.15 | NodeswL2MgmtMIBTraps | |||
| 1.3.6.1.4.1.171.11.78.1.2.15.1 | NodeswL2Notify | |||
| 1.3.6.1.4.1.171.11.78.1.2.15.1.2 | NodeswL2NotifyPrefix | |||
| 1.3.6.1.4.1.171.11.78.1.2.15.1.2.0 | NodeswL2NotifFirmware | |||
| 1.3.6.1.4.1.171.11.78.1.2.16 | NodeswL2RstpMgmt |