DGS-1100-06ME-AX
1187 objects
In order to pass the web www.simpleweb.org to verify severity level 3, which must be change the SYNTAX of mib file.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.171 | Noded-link | |||
| 1.3.6.1.4.1.171.10 | Nodedlink-products | |||
| 1.3.6.1.4.1.171.10.134 | Nodedlink-DGS1100SeriesProd | |||
| 1.3.6.1.4.1.171.10.134.1 | Nodedgs-1100-06ME | |||
| 1.3.6.1.4.1.171.10.134.1.1 | Identitydgs-1100-06ME-A1 | In order to pass the web www.simpleweb.org to verify severity level 3, which must be change the SYNTAX of mib file. | ||
| 1.3.6.1.4.1.171.10.134.1.1.1 | NodecompanySystem | |||
| 1.3.6.1.4.1.171.10.134.1.1.1.1 | ScalarsysSwitchName | read-write | current | System name used for identification of the device. The following characters are allowed to input. 0 ~ 9 / a ~ z / A ~ Z Special character |
| 1.3.6.1.4.1.171.10.134.1.1.1.2 | ScalarsysHardwareVersion | read-only | current | Version number of the Hardware. |
| 1.3.6.1.4.1.171.10.134.1.1.1.3 | ScalarsysFirmwareVersion | read-only | current | Version number of the Firmware. |
| 1.3.6.1.4.1.171.10.134.1.1.1.4 | ScalarsysLoginTimeoutInterval | read-write | current | This time interval is used to count the time and logout web interface automatically. |
| 1.3.6.1.4.1.171.10.134.1.1.1.5 | ScalarsysLocationName | read-write | current | The location name of this node (e.g., `telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string. |
| 1.3.6.1.4.1.171.10.134.1.1.1.6 | ScalarsysGroupInterval | read-write | current | Group Interval is used to send D-link Discover packet to D-link SmartConsole Utility frequency. The timer in units of seconds. Set value 0 to disable group Int… |
| 1.3.6.1.4.1.171.10.134.1.1.1.8 | ScalarsysSafeGuardEnable | read-write | current | This object is used to set Safeguard Enable\Disable. |
| 1.3.6.1.4.1.171.10.134.1.1.1.9 | ScalarsysRestart | read-write | current | This object allows the user to restart the Switch (i.e)the entire switch will operationally go down and start again. Setting a value of 'true' causes the switc… |
| 1.3.6.1.4.1.171.10.134.1.1.1.10 | ScalarsysSave | read-write | current | This object is used to save Configuration , value 1 save config_1 , value 2 is not in process , value 3 is save config_1 and value 4 is save config_2. |
| 1.3.6.1.4.1.171.10.134.1.1.1.12 | ScalarsysJumboFrameEnable | read-write | current | Gigabit Web Smart Switches support jumbo frames (frames larger than the Ethernet frame size of 1522 bytes) of up to 10,000 bytes (tagged). Default jumbo frame … |
| 1.3.6.1.4.1.171.10.134.1.1.1.13 | TablesysPortCtrlTable | not-accessible | current | A table to control the port specific parameters of the device like speed, duplex mode, etc. |
| 1.3.6.1.4.1.171.10.134.1.1.1.13.1 | RowsysPortCtrlEntry | not-accessible | current | An entry appears in this table for each interface in the system. Index to the table is the interface index of the port. |
| 1.3.6.1.4.1.171.10.134.1.1.1.13.1.1 | ColumnsysPortCtrlIndex | read-only | current | Interface index of the port for the configuration in this entry applies. |
| 1.3.6.1.4.1.171.10.134.1.1.1.13.1.2 | ColumnsysPortCtrlMediumType | read-only | current | This object indicates the port type: fiber 1G/100M or copper. |
| 1.3.6.1.4.1.171.10.134.1.1.1.13.1.3 | ColumnsysPortCtrlSpeed | read-write | current | Configures interface speed. |
| 1.3.6.1.4.1.171.10.134.1.1.1.13.1.4 | ColumnsysPortCtrlOperStatus | read-only | current | The port's operating speed state. |
| 1.3.6.1.4.1.171.10.134.1.1.1.13.1.5 | ColumnsysPortCtrlMDI | read-write | current | Configures interface auto/mdi/mdix mode. The default setting is Auto. |
| 1.3.6.1.4.1.171.10.134.1.1.1.13.1.6 | ColumnsysPortCtrlFlowControl | read-write | current | Enables / disables flow control for the interface. |
| 1.3.6.1.4.1.171.10.134.1.1.1.13.1.7 | ColumnsysPortCtrlFlowControlOper | read-only | current | The link parner negotiate port's operating flow control state. |
| 1.3.6.1.4.1.171.10.134.1.1.1.13.1.8 | ColumnsysPortCtrlType | read-only | current | The port's media type. |
| 1.3.6.1.4.1.171.10.134.1.1.1.13.1.9 | ColumnsysPortCtrlCapability | read-write | current | The port's capability advertised. |
| 1.3.6.1.4.1.171.10.134.1.1.1.14 | TablesysPortDescriptionTable | not-accessible | current | The port description table. |
| 1.3.6.1.4.1.171.10.134.1.1.1.14.1 | RowsysPortDescriptionEntry | not-accessible | current | The port description entry. |
| 1.3.6.1.4.1.171.10.134.1.1.1.14.1.1 | ColumnsysPortDescIndex | read-only | current | This object indicates the port index. |
| 1.3.6.1.4.1.171.10.134.1.1.1.14.1.2 | ColumnsysPortDescMediumType | read-only | current | This object indicates the port type: fiber 1G/100M or copper. |
| 1.3.6.1.4.1.171.10.134.1.1.1.14.1.3 | ColumnsysPortDescString | read-write | current | This object indicates the port description. |
| 1.3.6.1.4.1.171.10.134.1.1.1.15 | TablesysPortErrTable | not-accessible | current | The port error table. |
| 1.3.6.1.4.1.171.10.134.1.1.1.15.1 | RowsysPortErrEntry | not-accessible | current | A list of information for the err port of the device. |
| 1.3.6.1.4.1.171.10.134.1.1.1.15.1.1 | ColumnsysPortErrPortIndex | read-only | current | This object indicates the module's port number.(1..Max port number in the module) |
| 1.3.6.1.4.1.171.10.134.1.1.1.15.1.2 | ColumnsysPortErrPortState | read-only | current | This object decides whether the port state is enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.1.15.1.3 | ColumnsysPortErrPortStatus | read-only | current | This object decides whether the PortStatus is err-disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.1.15.1.4 | ColumnsysPortErrPortReason | read-only | current | This object decides whether the PortStatus is LBD. |
| 1.3.6.1.4.1.171.10.134.1.1.1.16 | ScalarsysDhcpAutoConfiguration | read-write | current | This object indicates auto config is enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.1.17 | ScalarsysWebState | read-write | current | This object is for Enabled(1) or Disabled(2) Web state in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.1.18 | ScalarsysWebPortNumber | read-write | current | Web Server Port Number. |
| 1.3.6.1.4.1.171.10.134.1.1.1.19 | ScalarsysARPAgingTime | read-write | current | This object is for ARP aging time. |
| 1.3.6.1.4.1.171.10.134.1.1.1.20 | ScalarsysMACAgingTime | read-write | current | This object is for MAC aging time. |
| 1.3.6.1.4.1.171.10.134.1.1.1.23 | ScalartelnetsettingManagementOnOff | read-write | current | Enable/Disable management Telnetsetting mechanism. |
| 1.3.6.1.4.1.171.10.134.1.1.1.24 | ScalartelnetUDPPort | read-write | current | The value is for setting telnet's UDP Port. |
| 1.3.6.1.4.1.171.10.134.1.1.1.25 | ScalarautoRefreshConfiguration | read-write | current | To set the WEB panel auto refresh timer. |
| 1.3.6.1.4.1.171.10.134.1.1.1.26 | ScalarfloodfdbOnOff | read-write | current | To set enable status for flood fdb. |
| 1.3.6.1.4.1.171.10.134.1.1.1.27 | ScalarsysContactName | read-write | current | To set system contact name. |
| 1.3.6.1.4.1.171.10.134.1.1.1.29 | ScalarsysCommandLogging | read-write | current | To set enable status for CommandLogging. |
| 1.3.6.1.4.1.171.10.134.1.1.1.30 | ScalarsysSerialNumber | read-only | current | To get the serial number. |
| 1.3.6.1.4.1.171.10.134.1.1.1.34 | ScalarsysDhcpAutoImage | read-write | current | This object indicates auto image is enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.1.35 | ScalarsysBootupConfigID | read-write | current | To get/set bootup config ID. |
| 1.3.6.1.4.1.171.10.134.1.1.1.36 | ScalarsysBootupImage | read-write | current | To get/set bootup Image. |
| 1.3.6.1.4.1.171.10.134.1.1.2 | NodecompanyIpifGroup | |||
| 1.3.6.1.4.1.171.10.134.1.1.2.7 | NodeipifSupportV4V6Info | |||
| 1.3.6.1.4.1.171.10.134.1.1.2.7.1 | ScalarsysIpAddrCfgMode | read-write | current | Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'sysDefault… |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.2 | ScalarsysIpAddr | read-write | current | Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored. |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.3 | ScalarsysIpSubnetMask | read-write | current | IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored. |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.4 | ScalarsysGateway | read-write | current | Gateway |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.5 | ScalardhcpOption12Status | read-write | current | Status of DHCP Option12 |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.6 | ScalardhcpOption12HostName | read-write | current | Host name in DHCP option 12 |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.7 | ScalaripifName | read-only | current | The Description for the interface. |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.8 | ScalaripifVLANname | read-only | current | The vlan name for the interface. |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.9 | Scalaripifv6GlobalStatus | read-write | current | The ID of VLAN that you want this interface to be in. It must be a exist vlan id. |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.10 | Scalaripifv6DHCPStatus | read-write | current | The state of DHCPv6 that you want this interface to be in. It must be a exist vlan id. |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.11 | Scalaripifv6AutolinkloStatus | read-write | current | The global state of link local that you want this interface to be in. It must be a exist vlan id. |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.12 | Scalaripifv6NSRetransmitTime | read-write | current | The NS's retransmit time that you want this interface to be in. It must be a exist vlan id (1~3600). |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.13 | Scalaripifv6DefaultGateway | read-write | current | The ipv6 default gateway that you want this interface to be in. It must be a exist vlan id. To delete gateway, please insert address '0000:0000:0000:0000:0000:… |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.14 | TableipifV6AddressTable | not-accessible | current | A list of interface entries. |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.14.1 | RowipifV6AddressEntry | not-accessible | current | An entry containing management information applicable to a particular interface. |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.14.1.1 | ColumnipifV6AddressMainIndex | read-only | current | The index of this IPv6 entry. |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.14.1.2 | ColumnipifV6AddressIpAddr | read-only | current | The ip address of this IPv6 entry. |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.14.1.3 | ColumnipifV6AddressIpPrefix | read-only | current | The ip prefix of this IPv6 entry. |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.14.1.4 | ColumnipifV6AddressIpType | read-only | current | The ip type of this IPv6 entry. |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.14.1.5 | ColumnipifV6AddressRowStatus | read-create | current | The status of an entry in the Multi Interface Table. Only a subset of the rowstatus variables (active, createAndWait, destroy) are available. |
| 1.3.6.1.4.1.171.10.134.1.1.2.7.15 | ScalardhcpRetryCount | read-write | current | Retry count of dhcp. |
| 1.3.6.1.4.1.171.10.134.1.1.3 | NodecompanyTftpGroup | |||
| 1.3.6.1.4.1.171.10.134.1.1.3.9 | NodetftpFwTargetGroup | |||
| 1.3.6.1.4.1.171.10.134.1.1.3.9.1 | ScalartftpFwTargetServerIpAddress | read-write | current | The TFTP server's IP address is used to upload or download firmware. |
| 1.3.6.1.4.1.171.10.134.1.1.3.9.2 | ScalartftpFwTargetServerIpType | read-write | current | Type of IP interface. |
| 1.3.6.1.4.1.171.10.134.1.1.3.9.3 | ScalartftpFwTargetInterfaceName | read-write | current | Specifies the interface name when the tftpFwTargetServerIpAddress is linklocal address. |
| 1.3.6.1.4.1.171.10.134.1.1.3.9.4 | ScalartftpFwTargetImageFileName | read-write | current | Configure firmware filename to download. |
| 1.3.6.1.4.1.171.10.134.1.1.3.9.5 | ScalartftpFwTargetTftpOperation | read-write | current | The tftp operates to perform downloading the firmware image to the unit. This object is used in conjunction with configBootTftpServerIp and configBootImageFile… |
| 1.3.6.1.4.1.171.10.134.1.1.3.9.6 | ScalartftpFwTargetTftpOperationStatus | read-only | current | The tftp operation status represent firmware backup or upgrade status. |
| 1.3.6.1.4.1.171.10.134.1.1.3.10 | NodetftpCfgTargetGroup | |||
| 1.3.6.1.4.1.171.10.134.1.1.3.10.1 | ScalartftpCfgTargetServerIpAddress | read-write | current | The TFTP server's IP address is used to upload or download configuration file. |
| 1.3.6.1.4.1.171.10.134.1.1.3.10.2 | ScalartftpCfgTargetServerIpType | read-write | current | Type of IP interface. |
| 1.3.6.1.4.1.171.10.134.1.1.3.10.3 | ScalartftpCfgTargetInterfaceName | read-write | current | Specifies the interface name when the tftpCfgTargetServerIpAddress is linklocal address. |
| 1.3.6.1.4.1.171.10.134.1.1.3.10.4 | ScalartftpCfgTargetImageFileName | read-write | current | The configuration filename is used to store or retrieve config from the tftp server. |
| 1.3.6.1.4.1.171.10.134.1.1.3.10.5 | ScalartftpCfgTargetTftpOperation | read-write | current | The tftp operates to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object … |
| 1.3.6.1.4.1.171.10.134.1.1.3.10.6 | ScalartftpCfgTargetTftpOperationStatus | read-only | current | The tftp operation status represent configuration file backup or restore status. |
| 1.3.6.1.4.1.171.10.134.1.1.4 | NodecompanyMiscGroup | |||
| 1.3.6.1.4.1.171.10.134.1.1.4.2 | ScalarmiscReset | read-write | current | Physically resets the unit - use with care. A (1) resets the unit, a (2) does nothing. |
| 1.3.6.1.4.1.171.10.134.1.1.4.3 | ScalarmiscStatisticsReset | read-write | current | Resets the units statistics. A (1) resets the statistics count, a (2) does nothing. |
| 1.3.6.1.4.1.171.10.134.1.1.5 | NodecompanySNMPV3 | |||
| 1.3.6.1.4.1.171.10.134.1.1.5.1 | ScalarsnmpGlobalState | read-write | current | This object is for enabling or disabling SNMP Community function. |
| 1.3.6.1.4.1.171.10.134.1.1.5.2 | NodesnmpV3User | |||
| 1.3.6.1.4.1.171.10.134.1.1.5.2.1 | TablesnmpV3UserTable | not-accessible | current | |
| 1.3.6.1.4.1.171.10.134.1.1.5.2.1.1 | RowsnmpV3UserEntry | not-accessible | current | |
| 1.3.6.1.4.1.171.10.134.1.1.5.2.1.1.1 | ColumnsnmpV3UserName | read-only | current | A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID. |
| 1.3.6.1.4.1.171.10.134.1.1.5.2.1.1.2 | ColumnsnmpV3UserVersion | read-only | current | A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID. |
| 1.3.6.1.4.1.171.10.134.1.1.5.2.1.1.3 | ColumnsnmpV3UserGroupName | read-create | current | The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAcces… |
| 1.3.6.1.4.1.171.10.134.1.1.5.2.1.1.4 | ColumnsnmpV3UserAuthProtocol | read-create | current | An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be authenticated, and if so, the type … |
| 1.3.6.1.4.1.171.10.134.1.1.5.2.1.1.5 | ColumnsnmpV3UserAuthProtocolPassword | read-create | current | |
| 1.3.6.1.4.1.171.10.134.1.1.5.2.1.1.6 | ColumnsnmpV3UserPrivProtocol | read-create | current | An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be protected from disclosure, and if s… |
| 1.3.6.1.4.1.171.10.134.1.1.5.2.1.1.7 | ColumnsnmpV3UserPrivProtocolPassword | read-create | current | |
| 1.3.6.1.4.1.171.10.134.1.1.5.2.1.1.8 | ColumnsnmpV3UserStatus | read-create | current | The status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the us… |
| 1.3.6.1.4.1.171.10.134.1.1.5.3 | NodesnmpV3Group | |||
| 1.3.6.1.4.1.171.10.134.1.1.5.3.1 | TablesnmpV3GroupTable | not-accessible | current | |
| 1.3.6.1.4.1.171.10.134.1.1.5.3.1.1 | RowsnmpV3GroupEntry | not-accessible | current | |
| 1.3.6.1.4.1.171.10.134.1.1.5.3.1.1.1 | ColumnsnmpV3GroupName | read-only | current | The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAcces… |
| 1.3.6.1.4.1.171.10.134.1.1.5.3.1.1.2 | ColumnsnmpV3GroupSecurityModel | read-only | current | In order to gain the access rights allowed by this conceptual row, this securityModel must be in use. |
| 1.3.6.1.4.1.171.10.134.1.1.5.3.1.1.3 | ColumnsnmpV3GroupSecurityLevel | read-only | current | The minimum level of security required in order to gain the access rights allowed by this conceptual row. A securityLevel of noAuthNoPriv is less than authNoPr… |
| 1.3.6.1.4.1.171.10.134.1.1.5.3.1.1.4 | ColumnsnmpV3GroupReadViewName | read-create | current | The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes read access. The identified MIB vie… |
| 1.3.6.1.4.1.171.10.134.1.1.5.3.1.1.5 | ColumnsnmpV3GroupWriteViewName | read-create | current | The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes write access. The identified MIB vi… |
| 1.3.6.1.4.1.171.10.134.1.1.5.3.1.1.6 | ColumnsnmpV3GroupNotifyViewName | read-create | current | The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes access for notifications. The ident… |
| 1.3.6.1.4.1.171.10.134.1.1.5.3.1.1.7 | ColumnsnmpV3GroupStatus | read-create | current | The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row … |
| 1.3.6.1.4.1.171.10.134.1.1.5.4 | NodesnmpV3ViewTree | |||
| 1.3.6.1.4.1.171.10.134.1.1.5.4.1 | TablesnmpV3ViewTreeTable | not-accessible | current | |
| 1.3.6.1.4.1.171.10.134.1.1.5.4.1.1 | RowsnmpV3ViewTreeEntry | not-accessible | current | |
| 1.3.6.1.4.1.171.10.134.1.1.5.4.1.1.1 | ColumnsnmpV3viewTreeName | read-only | current | The human readable name for a family of view subtrees. |
| 1.3.6.1.4.1.171.10.134.1.1.5.4.1.1.2 | ColumnsnmpV3viewTreeSubtree | read-only | current | The MIB subtree which when combined with the corresponding instance of vacmViewTreeFamilyMask defines a family of view subtrees. |
| 1.3.6.1.4.1.171.10.134.1.1.5.4.1.1.3 | ColumnsnmpV3viewTreeMask | read-create | current | The bit mask which, in combination with the corresponding instance of vacmViewTreeFamilySubtree, defines a family of view subtrees. Each bit of this bit mask c… |
| 1.3.6.1.4.1.171.10.134.1.1.5.4.1.1.4 | ColumnsnmpV3viewTreeType | read-create | current | Indicates whether the corresponding instances of vacmViewTreeFamilySubtree and vacmViewTreeFamilyMask define a family of view subtrees which is included in or … |
| 1.3.6.1.4.1.171.10.134.1.1.5.4.1.1.5 | ColumnsnmpV3viewTreeStatus | read-create | current | The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row … |
| 1.3.6.1.4.1.171.10.134.1.1.5.5 | NodesnmpV3Community | |||
| 1.3.6.1.4.1.171.10.134.1.1.5.5.1 | TablesnmpV3CommunityTable | not-accessible | current | |
| 1.3.6.1.4.1.171.10.134.1.1.5.5.1.1 | RowsnmpV3CommunityEntry | not-accessible | current | |
| 1.3.6.1.4.1.171.10.134.1.1.5.5.1.1.1 | ColumnsnmpV3CommunityName | read-only | current | The unique index value of a row in this table. |
| 1.3.6.1.4.1.171.10.134.1.1.5.5.1.1.2 | ColumnsnmpV3CommunityPolicy | read-create | current | A human readable string representing the corresponding value of snmpCommunityName in a Security Model independent format. |
| 1.3.6.1.4.1.171.10.134.1.1.5.5.1.1.3 | ColumnsnmpV3CommunityStatus | read-create | current | The status of this conceptual row in the snmpCommunityTable. An entry in this table is not qualified for activation until instances of all corresponding column… |
| 1.3.6.1.4.1.171.10.134.1.1.5.6 | NodesnmpV3Host | |||
| 1.3.6.1.4.1.171.10.134.1.1.5.6.2 | TablesnmpV3HostTable | not-accessible | current | |
| 1.3.6.1.4.1.171.10.134.1.1.5.6.2.1 | RowsnmpV3HostEntry | not-accessible | current | |
| 1.3.6.1.4.1.171.10.134.1.1.5.6.2.1.1 | ColumnsnmpV3HostAddress | read-only | current | This object contains a transport address. The format of this address depends on the value of the snmpTargetAddrTDomain object. And this object is unique identi… |
| 1.3.6.1.4.1.171.10.134.1.1.5.6.2.1.2 | ColumnsnmpV3IPType | read-only | current | Type of IP interface. |
| 1.3.6.1.4.1.171.10.134.1.1.5.6.2.1.3 | ColumnsnmpV3HostCommunityName | read-create | current | The locally arbitrary. |
| 1.3.6.1.4.1.171.10.134.1.1.5.6.2.1.4 | ColumnsnmpV3HostVersion | read-create | current | The Level of Security to be used when generating SNMP messages using this entry. |
| 1.3.6.1.4.1.171.10.134.1.1.5.6.2.1.5 | ColumnsnmpV3HostInterfaceName | read-create | current | Specifies the interface name when the syslogSrvIP is linklocal address. |
| 1.3.6.1.4.1.171.10.134.1.1.5.6.2.1.6 | ColumnsnmpV3HostStatus | read-create | current | |
| 1.3.6.1.4.1.171.10.134.1.1.5.7 | ScalarsnmpV3EngineID | read-write | current | An SNMP engine's administratively-unique identifier. In a simple agent, this value is always that agent's own snmpEngineID value. The value can also take the v… |
| 1.3.6.1.4.1.171.10.134.1.1.5.8 | NodesnmpV3Trap | |||
| 1.3.6.1.4.1.171.10.134.1.1.5.8.1 | ScalarsnmpV3TrapSNMPAuthentication | read-write | current | This object is for enabling or disabling SNMP login fail event trap in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.5.8.2 | ScalarsnmpV3TrapColdStart | read-write | current | This object is for enabling or disabling devie Bootup event trap in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.5.8.3 | ScalarsnmpV3TrapWarmStart | read-write | current | This object is for enabling or disabling devie Bootup event trap in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.5.8.4 | ScalarsnmpV3TrapLinkUpDown | read-write | current | This object is for enabling or disabling Copper link up / link down event trap in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.5.8.12 | ScalarsnmpV3TrapPortSecurity | read-write | current | |
| 1.3.6.1.4.1.171.10.134.1.1.5.8.14 | ScalarsnmpV3TrapLBD | read-write | current | |
| 1.3.6.1.4.1.171.10.134.1.1.7 | NodecompanyDot1qVlanGroup | |||
| 1.3.6.1.4.1.171.10.134.1.1.7.2 | Scalardot1qVlanManagementOnOff | read-write | current | Enable/Disable management VLAN mechanism. |
| 1.3.6.1.4.1.171.10.134.1.1.7.3 | Scalardot1qVlanManagementid | read-write | current | The management VLAN ID, which will allow to forward packets of that VLAN to CPU. |
| 1.3.6.1.4.1.171.10.134.1.1.7.5 | Scalardot1qVlanAsyOnOff | read-write | current | Enable/Disable IEEE 802.1Q Asymmetric VLAN |
| 1.3.6.1.4.1.171.10.134.1.1.7.6 | Tabledot1qVlanTable | not-accessible | current | A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and wi… |
| 1.3.6.1.4.1.171.10.134.1.1.7.6.1 | Rowdot1qVlanEntry | not-accessible | current | Information for a VLAN configured into the device by (local or network) management. |
| 1.3.6.1.4.1.171.10.134.1.1.7.6.1.1 | Columndot1qVlanName | read-create | current | An administratively assigned string, which may be used to identify the VLAN. |
| 1.3.6.1.4.1.171.10.134.1.1.7.6.1.2 | Columndot1qVlanEgressPorts | read-create | current | The set of ports which are permanently assigned to the egress list for this VLAN by management. Changes to a bit in this object affect the per-port per-VLAN Re… |
| 1.3.6.1.4.1.171.10.134.1.1.7.6.1.3 | Columndot1qVlanForbiddenPorts | read-only | current | The set of ports which are prohibited by management from being included in the egress list for this VLAN. Changes to this object that cause a port to be includ… |
| 1.3.6.1.4.1.171.10.134.1.1.7.6.1.4 | Columndot1qVlanUntaggedPorts | read-create | current | The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (dot1qVlanIndex = 1) is … |
| 1.3.6.1.4.1.171.10.134.1.1.7.6.1.6 | Columndot1qVlanRowStatus | read-create | current | The status of a row in dot1qVlanTable. By setting this object, new entries can be created in dot1qVlanTable and existing entries can be removed from dot1qVlanT… |
| 1.3.6.1.4.1.171.10.134.1.1.7.7 | Tabledot1qVlanPortTable | not-accessible | current | A table containing per port control and status information for VLAN configuration in the device. |
| 1.3.6.1.4.1.171.10.134.1.1.7.7.1 | Rowdot1qVlanPortEntry | not-accessible | current | Information controlling VLAN configuration for a port on the device. |
| 1.3.6.1.4.1.171.10.134.1.1.7.7.1.1 | Columndot1qVlanPvid | read-write | current | The PVID, the VLAN ID assigned to untagged frames or Priority-Tagged frames received on this port. |
| 1.3.6.1.4.1.171.10.134.1.1.7.9 | Scalardot1qVlanPVIDAutoAssignOnOff | read-write | current | Enable/Disable VLAN PVID auto assignment |
| 1.3.6.1.4.1.171.10.134.1.1.9 | NodecompanyStaticMAC | |||
| 1.3.6.1.4.1.171.10.134.1.1.9.1 | ScalarstaticDisableAutoLearn | read-write | current | Set on to disable Auto Learning Excluding Uplink Port and set off to enable Auto Learning. |
| 1.3.6.1.4.1.171.10.134.1.1.9.2 | ScalarstaticAutoLearningList | read-write | current | The set of the device's member ports that belong to the Static MAC auto learning enable/disable. For example, when Disable Auto Learning is enable, the octet v… |
| 1.3.6.1.4.1.171.10.134.1.1.9.3 | TablestaticTable | not-accessible | current | A list of the Static MACs |
| 1.3.6.1.4.1.171.10.134.1.1.9.3.1 | RowstaticEntry | not-accessible | current | A Static MAC entry containing the mac and forwarding port. |
| 1.3.6.1.4.1.171.10.134.1.1.9.3.1.1 | ColumnstaticVlanID | read-only | current | The VLAN ID of the static MAC entry. |
| 1.3.6.1.4.1.171.10.134.1.1.9.3.1.2 | ColumnstaticMac | read-only | current | The MAC address associated of the static MAC entry. |
| 1.3.6.1.4.1.171.10.134.1.1.9.3.1.3 | ColumnstaticPort | read-only | current | The forwarding port of the static MAC entry. For all machines give maximum port number. |
| 1.3.6.1.4.1.171.10.134.1.1.9.3.1.4 | ColumnstaticStatus | read-write | current | The status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. The trunk member port ca… |
| 1.3.6.1.4.1.171.10.134.1.1.9.4 | TableautoFdbTable | not-accessible | current | A list of the Auto Fdb |
| 1.3.6.1.4.1.171.10.134.1.1.9.4.1 | RowautoFdbEntry | not-accessible | current | A auto fdb entry containing the ipaddress |
| 1.3.6.1.4.1.171.10.134.1.1.9.4.1.1 | ColumnautoFdbIPAddress | read-only | current | The IpAddress of the autoFdbEntry. |
| 1.3.6.1.4.1.171.10.134.1.1.9.4.1.2 | ColumnautoFdbVlanID | read-only | current | The VlanID of the autoFdbEntry. |
| 1.3.6.1.4.1.171.10.134.1.1.9.4.1.3 | ColumnautoFdbMacAddress | read-only | current | The Mac Address of the autoFdbEntry. |
| 1.3.6.1.4.1.171.10.134.1.1.9.4.1.4 | ColumnautoFdbPort | read-only | current | The Port of the autoFdbEntry. |
| 1.3.6.1.4.1.171.10.134.1.1.9.4.1.5 | ColumnautoFdbTimeStamp | read-only | current | The Time Stamp of the autoFdbEntry. |
| 1.3.6.1.4.1.171.10.134.1.1.9.4.1.6 | ColumnautoFdbStatus | read-write | current | The status of an entry in the Auto Fdb Table. Only a subset of the rowstatus variables (createAndGo, createAndWait,destroy) are available. |
| 1.3.6.1.4.1.171.10.134.1.1.10 | NodecompanyIgsGroup | |||
| 1.3.6.1.4.1.171.10.134.1.1.10.1 | NodeigsSystem | |||
| 1.3.6.1.4.1.171.10.134.1.1.10.1.1 | ScalarigsStatus | read-write | current | Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module starts protocol operations. When set to 'disabled', the IGS module stops… |
| 1.3.6.1.4.1.171.10.134.1.1.10.1.2 | ScalarigsRouterPortPurgeInterval | read-write | current | This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInter… |
| 1.3.6.1.4.1.171.10.134.1.1.10.1.3 | ScalarigsHostPortPurgeInterval | read-write | current | This is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received this timer runs for 'PortPurg… |
| 1.3.6.1.4.1.171.10.134.1.1.10.1.4 | ScalarigsRobustnessValue | read-write | current | When the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attrib… |
| 1.3.6.1.4.1.171.10.134.1.1.10.1.5 | ScalarigsGrpQueryInterval | read-write | current | The value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there is any intersted receive… |
| 1.3.6.1.4.1.171.10.134.1.1.10.1.6 | ScalarigsQueryInterval | read-write | current | This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for VLANs. |
| 1.3.6.1.4.1.171.10.134.1.1.10.1.7 | ScalarigsQueryMaxResponseTime | read-write | current | The maximum query response time advertised in IGMPv2 general queries on this interface. |
| 1.3.6.1.4.1.171.10.134.1.1.10.1.9 | ScalarigsReportToAllPort | read-write | current | Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module forwards packets to report to all port. When set to 'disabled', the IGS … |
| 1.3.6.1.4.1.171.10.134.1.1.10.3 | NodeigsVlan | |||
| 1.3.6.1.4.1.171.10.134.1.1.10.3.3 | TableigsVlanRouterTable | not-accessible | current | This table contains the list of ports through which a router, in a particular VLAN is reachable. |
| 1.3.6.1.4.1.171.10.134.1.1.10.3.3.1 | RowigsVlanRouterEntry | not-accessible | current | Contains the VLAN ID and list of ports on which routers are present in the VLAN. |
| 1.3.6.1.4.1.171.10.134.1.1.10.3.3.1.1 | ColumnigsVlanRouterVlanId | read-only | current | VLAN ID of the ports through which router is reachable. |
| 1.3.6.1.4.1.171.10.134.1.1.10.3.3.1.2 | ColumnigsVlanRouterPortList | read-only | current | List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically. |
| 1.3.6.1.4.1.171.10.134.1.1.10.3.4 | TableigsVlanFilterTable | not-accessible | current | This table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.10.3.4.1 | RowigsVlanFilterEntry | not-accessible | current | Contains snooping status , version and fast leave configuration for a specific VLAN. |
| 1.3.6.1.4.1.171.10.134.1.1.10.3.4.1.1 | ColumnigsVlanFilterVlanId | read-only | current | Index of IgsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in IgsVlanFilterEntry is to be done. |
| 1.3.6.1.4.1.171.10.134.1.1.10.3.4.1.2 | ColumnigsVlanSnoopStatus | read-write | current | This object allows you to enable/disable IGS function on a specific VLAN. |
| 1.3.6.1.4.1.171.10.134.1.1.10.3.4.1.3 | ColumnigsVlanQuerier | read-only | current | Indicates whether the switch is configured as a querier in the VLAN |
| 1.3.6.1.4.1.171.10.134.1.1.10.3.4.1.4 | ColumnigsVlanCfgQuerier | read-write | current | The snooping switch can be configured as a querier via this object to send out IGMP general queries when IGMP routers are not present in the VLAN. When set to … |
| 1.3.6.1.4.1.171.10.134.1.1.10.3.4.1.5 | ColumnigsVlanQueryInterval | read-only | current | This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as … |
| 1.3.6.1.4.1.171.10.134.1.1.10.3.4.1.6 | ColumnigsVlanRtrPortList | read-write | current | List of ports which are configured statically as router ports |
| 1.3.6.1.4.1.171.10.134.1.1.10.3.4.1.8 | ColumnigsVlanFastLeave | read-write | current | Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for … |
| 1.3.6.1.4.1.171.10.134.1.1.10.3.5 | TableigsVlanMulticastGroupTable | not-accessible | current | This table contains MAC based multicast forwarding information. |
| 1.3.6.1.4.1.171.10.134.1.1.10.3.5.1 | RowigsVlanMulticastGroupEntry | not-accessible | current | This table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded. |
| 1.3.6.1.4.1.171.10.134.1.1.10.3.5.1.1 | ColumnigsVlanMulticastGroupVlanId | read-only | current | VLAN ID pertaining to the Multicast forwarding entry |
| 1.3.6.1.4.1.171.10.134.1.1.10.3.5.1.2 | ColumnigsVlanMulticastGroupIpAddress | read-only | current | Multicast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format. |
| 1.3.6.1.4.1.171.10.134.1.1.10.3.5.1.3 | ColumnigsVlanMulticastGroupMacAddress | read-only | current | Multicast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format. |
| 1.3.6.1.4.1.171.10.134.1.1.10.3.5.1.4 | ColumnigsVlanMulticastGroupPortList | read-only | current | List of ports onto which the multicast data packets destined for this group will be forwarded. |
| 1.3.6.1.4.1.171.10.134.1.1.10.5 | NodeigsAccessAuth | |||
| 1.3.6.1.4.1.171.10.134.1.1.10.5.1 | TableigsAccessAuthTable | not-accessible | current | This table is used to manage the IGMP Authentication function of the switch. |
| 1.3.6.1.4.1.171.10.134.1.1.10.5.1.1 | RowigsAccessAuthEntry | not-accessible | current | Contains management entities for IGMP Authentication function. |
| 1.3.6.1.4.1.171.10.134.1.1.10.5.1.1.1 | ColumnigsAccessAuthPortIndex | read-only | current | The port index of igsAccessAuthTable which indicates the port to be configured. For all machines give maximum port number. |
| 1.3.6.1.4.1.171.10.134.1.1.10.5.1.1.2 | ColumnigsAccessAuthState | read-write | current | This object can be configured to set IGMP Authentication state to enabled/disabled on each port. |
| 1.3.6.1.4.1.171.10.134.1.1.10.6 | NodeigsHost | |||
| 1.3.6.1.4.1.171.10.134.1.1.10.6.1 | TableigsHostTable | not-accessible | current | This table is used to manage the IGMP Host based Fast Leave function of the switch. |
| 1.3.6.1.4.1.171.10.134.1.1.10.6.1.1 | RowigsHostEntry | not-accessible | current | Contains management entities for IGMP Host based fast leave function. |
| 1.3.6.1.4.1.171.10.134.1.1.10.6.1.1.1 | ColumnigsHostTableVLANID | read-only | current | VLAN ID of Host table entry. |
| 1.3.6.1.4.1.171.10.134.1.1.10.6.1.1.2 | ColumnigsHostTableGroupAddress | read-only | current | Group address of Host table entry. |
| 1.3.6.1.4.1.171.10.134.1.1.10.6.1.1.3 | ColumnigsHostTablePort | read-only | current | Port number of Host table entry. For all machines give maximum port number. |
| 1.3.6.1.4.1.171.10.134.1.1.10.6.1.1.4 | ColumnigsHostTableHostIPAddress | read-only | current | Host IP address of Group in Host table entry. |
| 1.3.6.1.4.1.171.10.134.1.1.12 | NodecompanyQoSGroup | |||
| 1.3.6.1.4.1.171.10.134.1.1.12.1 | ScalarqosMode | read-write | current | Settings of Qos mode: IEEE 802.1p QoS or DSCP QoS. IEEE 802.1p : It specifies a priority(0~7) value to four queues in WS3 : Low(1,2), Medium(0,3), High(4,5) an… |
| 1.3.6.1.4.1.171.10.134.1.1.12.2 | ScalarqueuingMechanism | read-write | current | Queuing mechanism. strictPriority(1) : Strict Priority wrr(2) : Weighted Round Robin Strict-priority scheduling is implemented with a special strict-priority s… |
| 1.3.6.1.4.1.171.10.134.1.1.12.3 | NodeqosQ1p | |||
| 1.3.6.1.4.1.171.10.134.1.1.12.3.1 | Tabledot1pPortTable | not-accessible | current | A list of 802.1p port default priority Entries. |
| 1.3.6.1.4.1.171.10.134.1.1.12.3.1.1 | Rowdot1pPortEntry | not-accessible | current | A list of 802.1p port default priority priorities. |
| 1.3.6.1.4.1.171.10.134.1.1.12.3.1.1.1 | Columndot1pPortIndex | read-only | current | A port identifier that is in the range of 1 to ifNumber. For all machines give maximum port number. |
| 1.3.6.1.4.1.171.10.134.1.1.12.3.1.1.2 | Columndot1pPortPriority | read-write | current | For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization. For… |
| 1.3.6.1.4.1.171.10.134.1.1.12.4 | NodeqosDiffServ | |||
| 1.3.6.1.4.1.171.10.134.1.1.12.4.1 | ScalarqosDiffServEnable | read-only | current | Display the DSCP(Differentiated services) function Enabled or Disabled. Notice : DiffServ Type is 2~7 bits in the TOS field. ex: If the DiffServ Type = 000011(… |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2 | NodeqosDiffServTypeGroup | |||
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.1 | ScalarqosDiffServType00 | read-write | current | DiffServ Type 0 : IP ToS value = 0 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.2 | ScalarqosDiffServType01 | read-write | current | DiffServ Type 01 : IP ToS value = 4 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.3 | ScalarqosDiffServType02 | read-write | current | DiffServ Type 02 : IP ToS value = 8 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.4 | ScalarqosDiffServType03 | read-write | current | DiffServ Type 03 : IP ToS value = 12 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.5 | ScalarqosDiffServType04 | read-write | current | DiffServ Type 04 : IP ToS value = 16 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.6 | ScalarqosDiffServType05 | read-write | current | DiffServ Type 05 : IP ToS value = 20 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.7 | ScalarqosDiffServType06 | read-write | current | DiffServ Type 06 : IP ToS value = 24 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.8 | ScalarqosDiffServType07 | read-write | current | DiffServ Type 07 : IP ToS value = 28 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.9 | ScalarqosDiffServType08 | read-write | current | DiffServ Type 08 : IP ToS value = 32 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.10 | ScalarqosDiffServType09 | read-write | current | DiffServ Type 09 : IP ToS value = 36 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.11 | ScalarqosDiffServType10 | read-write | current | DiffServ Type 10 : IP ToS value = 40 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.12 | ScalarqosDiffServType11 | read-write | current | DiffServ Type 11 : IP ToS value = 44 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.13 | ScalarqosDiffServType12 | read-write | current | DiffServ Type 12 : IP ToS value = 48 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.14 | ScalarqosDiffServType13 | read-write | current | DiffServ Type 13 : IP ToS value = 52 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.15 | ScalarqosDiffServType14 | read-write | current | DiffServ Type 14 : IP ToS value = 56 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.16 | ScalarqosDiffServType15 | read-write | current | DiffServ Type 15 : IP ToS value = 60 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.17 | ScalarqosDiffServType16 | read-write | current | DiffServ Type 16 : IP ToS value = 64 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.18 | ScalarqosDiffServType17 | read-write | current | DiffServ Type 17 : IP ToS value = 68 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.19 | ScalarqosDiffServType18 | read-write | current | DiffServ Type 18 : IP ToS value = 72 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.20 | ScalarqosDiffServType19 | read-write | current | DiffServ Type 19 : IP ToS value = 76 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.21 | ScalarqosDiffServType20 | read-write | current | DiffServ Type 20 : IP ToS value = 80 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.22 | ScalarqosDiffServType21 | read-write | current | DiffServ Type 21 : IP ToS value = 84 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.23 | ScalarqosDiffServType22 | read-write | current | DiffServ Type 22 : IP ToS value = 88 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.24 | ScalarqosDiffServType23 | read-write | current | DiffServ Type 23 : IP ToS value = 92 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.25 | ScalarqosDiffServType24 | read-write | current | DiffServ Type 24 : IP ToS value = 96 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.26 | ScalarqosDiffServType25 | read-write | current | DiffServ Type 25 : IP ToS value = 100 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.27 | ScalarqosDiffServType26 | read-write | current | DiffServ Type 26 : IP ToS value = 104 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.28 | ScalarqosDiffServType27 | read-write | current | DiffServ Type 27 : IP ToS value = 108 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.29 | ScalarqosDiffServType28 | read-write | current | DiffServ Type 28 : IP ToS value = 112 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.30 | ScalarqosDiffServType29 | read-write | current | DiffServ Type 29 : IP ToS value = 116 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.31 | ScalarqosDiffServType30 | read-write | current | DiffServ Type 30 : IP ToS value = 120 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.32 | ScalarqosDiffServType31 | read-write | current | DiffServ Type 31 : IP ToS value = 124 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.33 | ScalarqosDiffServType32 | read-write | current | DiffServ Type 32 : IP ToS value = 128 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.34 | ScalarqosDiffServType33 | read-write | current | DiffServ Type 33 : IP ToS value = 132 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.35 | ScalarqosDiffServType34 | read-write | current | DiffServ Type 34 : IP ToS value = 136 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.36 | ScalarqosDiffServType35 | read-write | current | DiffServ Type 35 : IP ToS value = 140 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.37 | ScalarqosDiffServType36 | read-write | current | DiffServ Type 36 : IP ToS value = 144 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.38 | ScalarqosDiffServType37 | read-write | current | DiffServ Type 37 : IP ToS value = 148 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.39 | ScalarqosDiffServType38 | read-write | current | DiffServ Type 38 : IP ToS value = 152 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.40 | ScalarqosDiffServType39 | read-write | current | DiffServ Type 39 : IP ToS value = 156 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.41 | ScalarqosDiffServType40 | read-write | current | DiffServ Type 40 : IP ToS value = 160 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.42 | ScalarqosDiffServType41 | read-write | current | DiffServ Type 41 : IP ToS value = 164 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.43 | ScalarqosDiffServType42 | read-write | current | DiffServ Type 42 : IP ToS value = 168 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.44 | ScalarqosDiffServType43 | read-write | current | DiffServ Type 43 : IP ToS value = 172 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.45 | ScalarqosDiffServType44 | read-write | current | DiffServ Type 44 : IP ToS value = 176 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.46 | ScalarqosDiffServType45 | read-write | current | DiffServ Type 45 : IP ToS value = 180 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.47 | ScalarqosDiffServType46 | read-write | current | DiffServ Type 46 : IP ToS value = 184 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.48 | ScalarqosDiffServType47 | read-write | current | DiffServ Type 47 : IP ToS value = 188 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.49 | ScalarqosDiffServType48 | read-write | current | DiffServ Type 48 : IP ToS value = 192 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.50 | ScalarqosDiffServType49 | read-write | current | DiffServ Type 49 : IP ToS value = 196 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.51 | ScalarqosDiffServType50 | read-write | current | DiffServ Type 50 : IP ToS value = 200 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.52 | ScalarqosDiffServType51 | read-write | current | DiffServ Type 51 : IP ToS value = 204 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.53 | ScalarqosDiffServType52 | read-write | current | DiffServ Type 52 : IP ToS value = 208 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.54 | ScalarqosDiffServType53 | read-write | current | DiffServ Type 53 : IP ToS value = 212 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.55 | ScalarqosDiffServType54 | read-write | current | DiffServ Type 54 : IP ToS value = 216 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.56 | ScalarqosDiffServType55 | read-write | current | DiffServ Type 55 : IP ToS value = 220 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.57 | ScalarqosDiffServType56 | read-write | current | DiffServ Type 56 : IP ToS value = 224 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.58 | ScalarqosDiffServType57 | read-write | current | DiffServ Type 57 : IP ToS value = 228 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.59 | ScalarqosDiffServType58 | read-write | current | DiffServ Type 58 : IP ToS value = 232 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.60 | ScalarqosDiffServType59 | read-write | current | DiffServ Type 59 : IP ToS value = 236 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.61 | ScalarqosDiffServType60 | read-write | current | DiffServ Type 60 : IP ToS value = 240 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.62 | ScalarqosDiffServType61 | read-write | current | DiffServ Type 61 : IP ToS value = 244 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.63 | ScalarqosDiffServType62 | read-write | current | DiffServ Type 62 : IP ToS value = 248 |
| 1.3.6.1.4.1.171.10.134.1.1.12.4.2.64 | ScalarqosDiffServType63 | read-write | current | DiffServ Type 63 : IP ToS value = 252 |
| 1.3.6.1.4.1.171.10.134.1.1.12.8 | NodeqosAclPrioritySettings | |||
| 1.3.6.1.4.1.171.10.134.1.1.12.8.2 | TableaclQosTable | not-accessible | current | A list of priority by acl setting. |
| 1.3.6.1.4.1.171.10.134.1.1.12.8.2.1 | RowaclQosEntry | not-accessible | current | A list of priority by acl setting entry. |
| 1.3.6.1.4.1.171.10.134.1.1.12.8.2.1.1 | ColumnaclQosIndex | read-only | current | Index of priority by acl setting. |
| 1.3.6.1.4.1.171.10.134.1.1.12.8.2.1.2 | ColumnaclQosType | read-write | current | Type of priority by aclqos setting. DGS-1100-06ME only support ipv6traffic_class. |
| 1.3.6.1.4.1.171.10.134.1.1.12.8.2.1.10 | ColumnaclQosIP6TC | read-write | current | Ipv6 Traffic Class number of priority by acl setting |
| 1.3.6.1.4.1.171.10.134.1.1.12.8.2.1.98 | ColumnaclQosAssignPriority | read-write | current | Be mapped class of priority by acl setting. |
| 1.3.6.1.4.1.171.10.134.1.1.12.8.2.1.99 | ColumnaclQosStatus | read-write | current | Status of priority by acl setting. |
| 1.3.6.1.4.1.171.10.134.1.1.13 | NodecompanyTrafficMgmt | |||
| 1.3.6.1.4.1.171.10.134.1.1.13.1 | NodebandwidthCtrlSettings | |||
| 1.3.6.1.4.1.171.10.134.1.1.13.1.2 | TablebandwidthCtrlTable | not-accessible | current | A table to control the rate limiting parameters either for the entire switch or for each interface in the switch. |
| 1.3.6.1.4.1.171.10.134.1.1.13.1.2.1 | RowbandwidthCtrlEntry | not-accessible | current | An entry appears in this table for each physical interface in the switch. |
| 1.3.6.1.4.1.171.10.134.1.1.13.1.2.1.1 | ColumnbandwidthCtrlIndex | read-only | current | The interface index for which the configuration in this entry applies. For all machines give maximum port number. |
| 1.3.6.1.4.1.171.10.134.1.1.13.1.2.1.2 | ColumnbandwidthCtrlTxThreshold | read-write | current | Configures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed.… |
| 1.3.6.1.4.1.171.10.134.1.1.13.1.2.1.3 | ColumnbandwidthCtrlRxThreshold | read-write | current | Allows to configure the limiting value for the maximum number of receive packets that can be transmitted per second over this interface. Setting this object to… |
| 1.3.6.1.4.1.171.10.134.1.1.13.1.2.1.4 | ColumnbandwidthEffecTxThreshold | read-only | current | This object's value will take effect on the interface speed. Based on the operating speed of the port, the rate limit will be applied. This value can also be a… |
| 1.3.6.1.4.1.171.10.134.1.1.13.1.2.1.5 | ColumnbandwidthEffecRxThreshold | read-only | current | Allows to configure the limiting value for the maximum number of receive packets that can be transmitted per second over this interface. Setting this object to… |
| 1.3.6.1.4.1.171.10.134.1.1.13.4 | NodetrafficCtrlSettings | |||
| 1.3.6.1.4.1.171.10.134.1.1.13.4.1 | ScalartrafficCtrlTrap | read-write | current | The trap setting of traffic control. |
| 1.3.6.1.4.1.171.10.134.1.1.13.4.2 | TabletrafficCtrlTable | not-accessible | current | The traffic control table. |
| 1.3.6.1.4.1.171.10.134.1.1.13.4.2.1 | RowtrafficCtrlEntry | not-accessible | current | The traffic control entry. |
| 1.3.6.1.4.1.171.10.134.1.1.13.4.2.1.1 | ColumntrafficCtrlIndex | read-only | current | The traffic control index. |
| 1.3.6.1.4.1.171.10.134.1.1.13.4.2.1.2 | ColumntrafficCtrlActionMode | read-write | current | The action mode of traffic control. |
| 1.3.6.1.4.1.171.10.134.1.1.13.4.2.1.3 | ColumntrafficCtrlType | read-write | current | The control type of traffic control. (b: Broadcast, m: Multicast, u: Unknown Unicast) |
| 1.3.6.1.4.1.171.10.134.1.1.13.4.2.1.4 | ColumntrafficCtrlThreshold | read-write | current | The threshold of traffic control. |
| 1.3.6.1.4.1.171.10.134.1.1.13.4.2.1.5 | ColumntrafficCtrlCountDown | read-write | current | The count down value of traffic control. |
| 1.3.6.1.4.1.171.10.134.1.1.13.4.2.1.6 | ColumntrafficCtrlTimeInterval | read-write | current | The time interval of traffic control. |
| 1.3.6.1.4.1.171.10.134.1.1.13.4.3 | ScalartrafficCtrlAutoRecoverTime | read-write | current | The recover time of traffic control. |
| 1.3.6.1.4.1.171.10.134.1.1.14 | NodecompanySecurity | |||
| 1.3.6.1.4.1.171.10.134.1.1.14.1 | NodesecurityTrustedHost | |||
| 1.3.6.1.4.1.171.10.134.1.1.14.1.1 | ScalartrustedHostStatus | read-write | current | This object indicates trusted host function is enabled or disabled. When trusted host function is enabled, D-Link Smart Switches will only allow hosts which yo… |
| 1.3.6.1.4.1.171.10.134.1.1.14.1.2 | Tableipv4trustedHostTable | not-accessible | obsolete | A table to configure trusted host in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.14.1.2.1 | Rowipv4trustedHostEntry | not-accessible | obsolete | Each entry in this table represents rules for particular trusted host. |
| 1.3.6.1.4.1.171.10.134.1.1.14.1.2.1.1 | Columnipv4trustedHostIpAddr | read-only | obsolete | The IP address of host you allow to access to D-Link Smart Switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection. |
| 1.3.6.1.4.1.171.10.134.1.1.14.1.2.1.2 | Columnipv4trustedHostIpMask | read-only | obsolete | Used to mask with IP address, it allow you set a subnet as a trusted host entry. |
| 1.3.6.1.4.1.171.10.134.1.1.14.1.2.1.3 | Columnipv4trustedHostRowStatus | read-create | obsolete | The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
| 1.3.6.1.4.1.171.10.134.1.1.14.1.3 | TabletrustedHostTable | not-accessible | current | A table to configure trusted host for in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.14.1.3.1 | RowtrustedHostEntry | not-accessible | current | Each entry in this table represents rules for particular trusted host. |
| 1.3.6.1.4.1.171.10.134.1.1.14.1.3.1.1 | ColumntrustedHostIPType | read-only | current | Type of IP interface. |
| 1.3.6.1.4.1.171.10.134.1.1.14.1.3.1.2 | ColumntrustedHostIpAddr | read-only | current | The IP address of host you allow to access to D-Link Smart Switch. Your local host IPv4/6 Addresses must be one of the IP Addresses to avoid disconnection. |
| 1.3.6.1.4.1.171.10.134.1.1.14.1.3.1.3 | ColumntrustedHostIpMask | read-only | current | Used to mask with IPv4/6 address, it allow you set a subnet as a trusted host entry. |
| 1.3.6.1.4.1.171.10.134.1.1.14.1.3.1.4 | ColumntrustedHostRowStatus | read-create | current | The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
| 1.3.6.1.4.1.171.10.134.1.1.14.2 | NodesecurityPortSecurity | |||
| 1.3.6.1.4.1.171.10.134.1.1.14.2.1 | TableportSecTable | not-accessible | current | A table to control port security features of the device. |
| 1.3.6.1.4.1.171.10.134.1.1.14.2.1.1 | RowportSecEntry | not-accessible | current | An entry appears in port security table for each interface in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.14.2.1.1.1 | ColumnportSecIndex | read-only | current | The interface index for which the configuration in this entry applies. For all machines give maximum port number. |
| 1.3.6.1.4.1.171.10.134.1.1.14.2.1.1.2 | ColumnportSecState | read-write | current | Enable / disable port security admin state for the interface. A given ports' dynamic MAC address learning will be stopped such that the current source MAC addr… |
| 1.3.6.1.4.1.171.10.134.1.1.14.2.1.1.3 | ColumnportSecMLA | read-write | current | Configures interface port security maximum learning address numbers. When given ports' admin state is enabled, allows forwarding table learning address number.… |
| 1.3.6.1.4.1.171.10.134.1.1.14.2.1.1.4 | ColumnportSecLockAddrMode | read-write | current | Configures port security lock address mode for the interface. deleteOnReset : The locked addresses will not age out until the Switch has been reset. deleteOnTi… |
| 1.3.6.1.4.1.171.10.134.1.1.14.2.2 | TableportSecFDBPermanentTable | not-accessible | current | A table to control port security FDB Permanent of the device. |
| 1.3.6.1.4.1.171.10.134.1.1.14.2.2.1 | RowportSecFDBPermanentEntry | not-accessible | current | An entry appears in port security table for each interface in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.14.2.2.1.1 | ColumnportSecFDBPermIndex | read-only | current | The index of the port security MAC entry. For all machines give maximum port number. |
| 1.3.6.1.4.1.171.10.134.1.1.14.2.2.1.2 | ColumnportSecFDBPermVlanID | read-only | current | The VLAN ID of the port security MAC entry. |
| 1.3.6.1.4.1.171.10.134.1.1.14.2.2.1.3 | ColumnportSecFDBPermMac | read-only | current | The MAC address associated of the port security MAC entry. |
| 1.3.6.1.4.1.171.10.134.1.1.14.2.2.1.4 | ColumnportSecFDBPermPort | read-only | current | The forwarding port of the port security MAC entry. For all machines give maximum port number. |
| 1.3.6.1.4.1.171.10.134.1.1.14.9 | NodesecurityTrafficSeg | |||
| 1.3.6.1.4.1.171.10.134.1.1.14.9.1 | TabletrafficSegTable | not-accessible | current | A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. Th… |
| 1.3.6.1.4.1.171.10.134.1.1.14.9.1.1 | RowtrafficSegEntry | not-accessible | current | There is one entry in this table for each created port-channel port |
| 1.3.6.1.4.1.171.10.134.1.1.14.9.1.1.1 | ColumntrafficSegIfIndex | read-only | current | The ifIndex of the port-channel(Aggregator's interface index). |
| 1.3.6.1.4.1.171.10.134.1.1.14.9.1.1.2 | ColumntrafficSegMemberList | read-write | current | Port list of port channel. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11 | NodesecurityAAC | |||
| 1.3.6.1.4.1.171.10.134.1.1.14.11.1 | ScalaraacAuthenAdminState | read-write | current | This object indicates the Access Authentication is enable or disable. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.2 | ScalaraacAuthParamResponseTimeout | read-write | current | Timeout in second for login authentication response. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.3 | ScalaraacAuthParamAttempt | read-write | current | The amount for login authentication, if login failure exceed, connection or access would be locked. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.4 | NodeaacAPAuthMethodGroup | |||
| 1.3.6.1.4.1.171.10.134.1.1.14.11.4.1 | NodeaacAPLoginMethod | |||
| 1.3.6.1.4.1.171.10.134.1.1.14.11.4.1.2 | ScalaraacAPTelnetLoginMethod | read-write | current | Specify the way which has to execute authentication while login the system and the method for authentication.Access system via telnet. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.4.1.4 | ScalaraacAPHttpLoginMethod | read-write | current | Specify the way which has to execute authentication while login the system and the method for authentication.Access system via HTTP. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.4.2 | NodeaacAPEnableMethod | |||
| 1.3.6.1.4.1.171.10.134.1.1.14.11.4.2.2 | ScalaraacAPTelnetEnableMethod | read-write | current | Specify the way which has to execute authentication while login the system and the method for authentication.Access system via telnet. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.4.2.4 | ScalaraacAPHttpEnableMethod | read-write | current | Specify the way which has to execute authentication while login the system and the method for authentication.Access system via HTTP. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.5 | TableaacServerGroupTable | not-accessible | current | A table that contains informations about server group. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.5.1 | RowaacServerGroupEntry | not-accessible | current | A list of the group including servers. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.5.1.1 | ColumnaacServerGroupIndex | read-only | current | A value that uniquely identifies this SwAACServerGroupEntry . |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.5.1.2 | ColumnaacServerGroupName | read-write | current | A human-readable text string of the method group. The name is writable only if Group is new created, which the value of aacServerGroupRowStatus is 'notReady'. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.5.1.3 | ColumnaacServersInGroup | read-write | current | The list of servers in the group, each bit indicates a specified server ID. The server must be created before including it. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.5.1.4 | ColumnaacServerGroupRowStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.7 | TableaacServerInfoTable | not-accessible | current | A table that contains information about severs. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.7.1 | RowaacServerInfoEntry | not-accessible | current | A list of the information of server . |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.7.1.1 | ColumnaacServerIndex | read-only | current | A value that uniquely identifies this SwAACServerGroupEntry. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.7.1.2 | ColumnaacServerIPType | read-write | current | The IP address of the AAC server IP type referred to in this table entry. (IPv4=1, IPv6=2) |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.7.1.3 | ColumnaacServerIPAddr | read-write | current | The IP address of Server |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.7.1.4 | ColumnaacServerInterfaceName | read-create | current | Specifies the interface name when the aacServerIPAddr is linklocal address. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.7.1.5 | ColumnaacServerAuthProtocol | read-write | current | The authentication protocol provided by the Server. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.7.1.6 | ColumnaacServerAuthPort | read-write | current | The TCP/IP port . |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.7.1.7 | ColumnaacServerAuthKey | read-write | current | The key used while authentication process. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.7.1.8 | ColumnaacServerTimeout | read-write | current | Server response timeout . |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.7.1.9 | ColumnaacServerRetryCount | read-write | current | Client retry count . (-1: No retry mechanism) |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.7.1.10 | ColumnaacServerRowStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.8 | TableaacLoginMethodListTable | not-accessible | current | A table that contains information about Login authentication method lists. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.8.1 | RowaacLoginMethodListEntry | not-accessible | current | A list of the Authentication methods. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.8.1.1 | ColumnaacLoginMethodListIndex | read-only | current | A value that identifies this method list. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.8.1.2 | ColumnaacLoginMethodListName | read-write | current | A human-readable text string of the method list. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.8.1.3 | ColumnaacLoginMethod1 | read-write | current | The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.8.1.4 | ColumnaacLoginMethod2 | read-write | current | The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.8.1.5 | ColumnaacLoginMethod3 | read-write | current | The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.8.1.6 | ColumnaacLoginMethod4 | read-write | current | The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.8.1.7 | ColumnaacLoginMethodListRowStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.9 | TableaacEnableMethodListTable | not-accessible | current | A table that contains information about Enable authentication method lists. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.9.1 | RowaacEnableMethodListEntry | not-accessible | current | A list of the Authentication methods. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.9.1.1 | ColumnaacEnableMethodListIndex | read-only | current | A value that identifies this method list. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.9.1.2 | ColumnaacEnableMethodListName | read-write | current | A human-readable text string of the method list. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.9.1.3 | ColumnaacEnableMethod1 | read-write | current | The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.9.1.4 | ColumnaacEnableMethod2 | read-write | current | The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.9.1.5 | ColumnaacEnableMethod3 | read-write | current | The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.9.1.6 | ColumnaacEnableMethod4 | read-write | current | The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.9.1.7 | ColumnaacEnableMethodListRowStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.134.1.1.14.11.10 | ScalaraacLocalEnablePassword | read-write | current | This object is used to set Local Enable Password. |
| 1.3.6.1.4.1.171.10.134.1.1.15 | NodecompanyACLGroup | |||
| 1.3.6.1.4.1.171.10.134.1.1.15.1 | NodeaclProfile | |||
| 1.3.6.1.4.1.171.10.134.1.1.15.1.1 | Tableipv4aclProfileTable | not-accessible | obsolete | A table to ACL profile . |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.1.1 | Rowipv4aclProfileEntry | not-accessible | obsolete | Each entry in this table is a ACL profile. Index to the table is ACL profile ID. |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.1.1.1 | Columnipv4aclProfileNo | read-only | obsolete | The ACL Profile ID. The ID 1 to 50 is user-defined ACL, and the ID more than 50 is reserved for system-defined ACL. The user only allow to create user-defined … |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.1.1.2 | Columnipv4aclProfileType | read-write | obsolete | The ACL Profile type, possible value are l2 (1) - for MAC-based rule, l3 (2) - for IPv4-based rule, voiceVlan(6) - for Voice VLAN OUI entry. userDefined(9) - f… |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.1.1.3 | Columnipv4aclProfileRuleCount | read-only | obsolete | The number of rules in this profile. |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.1.1.4 | Columnipv4aclProfileMask | read-write | obsolete | Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT L2 DST_MAC 0 (LSB) L2 SRC_MAC 1 L2 VID … |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.1.1.5 | Columnipv4aclProfileDstMacAddrMask | read-write | obsolete | The ACL Profile destination MAC address mask. If DST_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleDstMacAddr, to caculate… |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.1.1.6 | Columnipv4aclProfileSrcMacAddrMask | read-write | obsolete | The ACL Profile source MAC address mask. If SRC_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleSrcMacAddr, to caculate a ra… |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.1.1.7 | Columnipv4aclProfileIPProtocol | read-write | obsolete | Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none. |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.1.1.8 | Columnipv4aclProfileIPProtocolMask | read-write | obsolete | The ACL Profile IP protocol mask. If aclProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule field,aclL3RuleProtocol,… |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.1.1.9 | Columnipv4aclProfileDstIpAddrMask | read-write | obsolete | The ACL Profile destination IP address mask. If DST_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleDstIpAddr, to caculate a … |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.1.1.10 | Columnipv4aclProfileSrcIpAddrMask | read-write | obsolete | The ACL Profile source IP address mask. If SRC_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleSrcIpAddr, to caculate a range… |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.1.1.11 | Columnipv4aclProfileDstPortMask | read-write | obsolete | The ACL Profile UDP/TCP destination port mask. If DST_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpDstPort, to cac… |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.1.1.12 | Columnipv4aclProfileSrcPortMask | read-write | obsolete | The ACL Profile UDP/TCP source port mask. If SRC_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpSrcPort, to caculate… |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.1.1.28 | Columnipv4aclProfileStatus | read-create | obsolete | This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait… |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.2 | TableaclProfileTable | not-accessible | current | A table to ACL profile . |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.2.1 | RowaclProfileEntry | not-accessible | current | Each entry in this table is a ACL profile. Index to the table is ACL profile ID. |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.2.1.1 | ColumnaclProfileNo | read-only | current | The ACL Profile ID. The ID 1 to 50 is user-defined ACL, and the ID more than 50 is reserved for system-defined ACL. The user only allow to create user-defined … |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.2.1.2 | ColumnaclProfileType | read-write | current | The ACL Profile type, possible value are l2 (1) - for MAC-based rule, l3v4 (2) - for IPv4-based rule, l3v6 (11) - for IPv6-based rule, voiceVlan(6) - for Voice… |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.2.1.3 | ColumnaclProfileRuleCount | read-only | current | The number of rules in this profile. |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.2.1.4 | ColumnaclProfileMask | read-write | current | Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT L2 DST_MAC 0 (LSB) L2 SRC_MAC 1 L2 VID … |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.2.1.5 | ColumnaclProfileDstMacAddrMask | read-write | current | The ACL Profile destination MAC address mask. If DST_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleDstMacAddr, to caculate… |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.2.1.6 | ColumnaclProfileSrcMacAddrMask | read-write | current | The ACL Profile source MAC address mask. If SRC_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleSrcMacAddr, to caculate a ra… |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.2.1.7 | ColumnaclProfileIPProtocol | read-write | current | Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none. |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.2.1.8 | ColumnaclProfileIPProtocolMask | read-write | current | The ACL Profile IP protocol mask. If aclProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule field,aclL3RuleProtocol,… |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.2.1.9 | ColumnaclProfileDstIpAddrMaskType | read-write | current | IPv6 Address type. |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.2.1.10 | ColumnaclProfileDstIpAddrMask | read-write | current | The ACL Profile destination IP address mask. If DST_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleDstIpAddr, to caculate a … |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.2.1.11 | ColumnaclProfileSrcIpAddrMaskType | read-write | current | IPv6 Address type. |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.2.1.12 | ColumnaclProfileSrcIpAddrMask | read-write | current | The ACL Profile source IP address mask. If SRC_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleSrcIpAddr, to caculate a range… |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.2.1.13 | ColumnaclProfileDstPortMask | read-write | current | The ACL Profile UDP/TCP destination port mask. If DST_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpDstPort, to cac… |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.2.1.14 | ColumnaclProfileSrcPortMask | read-write | current | The ACL Profile UDP/TCP source port mask. If SRC_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpSrcPort, to caculate… |
| 1.3.6.1.4.1.171.10.134.1.1.15.1.2.1.30 | ColumnaclProfileStatus | read-create | current | This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait… |
| 1.3.6.1.4.1.171.10.134.1.1.15.2 | NodeaclL2Rule | |||
| 1.3.6.1.4.1.171.10.134.1.1.15.2.1 | TableaclL2RuleTable | not-accessible | current | A table to configure L2 filter rules in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.15.2.1.1 | RowaclL2RuleEntry | not-accessible | current | Each entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID. |
| 1.3.6.1.4.1.171.10.134.1.1.15.2.1.1.1 | ColumnaclL2AccessID | read-only | current | L2 Filter rule ID. 0 means auto assign. |
| 1.3.6.1.4.1.171.10.134.1.1.15.2.1.1.2 | ColumnaclL2ProfileID | read-only | current | ACL Profile ID which this rule join. |
| 1.3.6.1.4.1.171.10.134.1.1.15.2.1.1.3 | ColumnaclL2RuleEtherType | read-write | current | The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '-1', which means the rule don't ca… |
| 1.3.6.1.4.1.171.10.134.1.1.15.2.1.1.4 | ColumnaclL2RuleDstMacAddr | read-write | current | Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero,which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.2.1.1.5 | ColumnaclL2RuleSrcMacAddr | read-write | current | Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero, which means the rule don't care this condition.. address |
| 1.3.6.1.4.1.171.10.134.1.1.15.2.1.1.6 | ColumnaclL2RuleVlanId | read-write | current | Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule… |
| 1.3.6.1.4.1.171.10.134.1.1.15.2.1.1.7 | ColumnaclL2Rule1pPriority | read-write | current | 802.1p priority to be matched with the packet. By Default, the value will be '-1', which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.2.1.1.8 | ColumnaclL2RuleDstMacAddrMask | read-only | current | The MAC address Mask work for Destination MAC address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.15.2.1.1.9 | ColumnaclL2RuleSrcMacAddrMask | read-only | current | The MAC address Mask work for Source MAC address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.15.2.1.1.10 | ColumnaclL2RuleInPortList | read-write | current | Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list. |
| 1.3.6.1.4.1.171.10.134.1.1.15.2.1.1.11 | ColumnaclL2RuleAction | read-write | current | Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding r… |
| 1.3.6.1.4.1.171.10.134.1.1.15.2.1.1.12 | ColumnaclL2RuleRateLimit | read-write | current | Rate limit for matched packet. |
| 1.3.6.1.4.1.171.10.134.1.1.15.2.1.1.13 | ColumnaclL2RuleReplaceDSCP | read-write | current | Replace DSCP for matched packet. |
| 1.3.6.1.4.1.171.10.134.1.1.15.2.1.1.15 | ColumnaclL2RuleNonIPFilterOnlyState | read-write | current | Enables / disables Non IP Filter Only State |
| 1.3.6.1.4.1.171.10.134.1.1.15.2.1.1.99 | ColumnaclL2RuleStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.134.1.1.15.3 | NodeaclL3Rule | |||
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1 | TableaclL3RuleTable | not-accessible | current | A table to configure L3 filter rules in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1 | RowaclL3RuleEntry | not-accessible | current | Each entry in this table is a L3 filter rule. Index to the table is L3 filter number and Profile ID. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.1 | ColumnaclL3RuleAccessID | read-only | current | L3 Filter rule ID. 0 means auto assign. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.2 | ColumnaclL3RuleProfileNo | read-only | current | The Profile ID which this rule join. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.3 | ColumnaclL3RuleProtocol | read-write | current | The type of protocol to be checked against the packet. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.4 | ColumnaclL3RuleProtocolMask | read-only | current | The IP protocol mask. This field is read-only and copy from it's Profile setting. It will work with the other field,aclL3RuleProtocol, to caculate a range of I… |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.5 | ColumnaclL3RuleICMPMessageType | read-write | current | The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action s… |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.6 | ColumnaclL3RuleICMPMessageCode | read-write | current | The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action s… |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.7 | ColumnaclL3RuleDstIpAddr | read-write | current | Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.8 | ColumnaclL3RuleSrcIpAddr | read-write | current | Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.9 | ColumnaclL3RuleDstIpAddrMask | read-only | current | The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.10 | ColumnaclL3RuleSrcIpAddrMask | read-only | current | The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.11 | ColumnaclL3RuleTcpUdpDstPort | read-write | current | The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.12 | ColumnaclL3RuleTcpUdpSrcPort | read-write | current | The TCP / UDP source port. The default value is -1, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.13 | ColumnaclL3RuleTcpUdpDstPortMask | read-only | current | The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.14 | ColumnaclL3RuleTcpUdpSrcPortMask | read-only | current | The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.15 | ColumnaclL3RuleTcpAckBit | read-create | current | The TCP ACK bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.16 | ColumnaclL3RuleTcpRstBit | read-create | current | The TCP RST bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.17 | ColumnaclL3RuleTcpUrgBit | read-create | current | The TCP Urg bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.18 | ColumnaclL3RuleTcpPshBit | read-create | current | The TCP Psh bit to be checked against the packet. The default value is 'dont_care'(-1). which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.19 | ColumnaclL3RuleTcpSynBit | read-create | current | The TCP Syn bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.20 | ColumnaclL3RuleTcpFinBit | read-create | current | The TCP Fin bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.21 | ColumnaclL3RuleDscp | read-create | current | The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.22 | ColumnaclL3RuleTos | read-create | current | The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.23 | ColumnaclL3RuleIgmpType | read-write | current | The IGMP Type to be checked against the packet.A default value is '-1', which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.24 | ColumnaclL3RulePortList | read-write | current | Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.25 | ColumnaclL3RuleAction | read-write | current | Specifies the action to be taken on the packet if the filter rule matches. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.26 | ColumnaclL3RuleRateLimit | read-write | current | Rate limit for matched packet. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.27 | ColumnaclL3RuleReplaceDSCP | read-write | current | ReplaceDSCP for matched packet. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.1.1.29 | ColumnaclL3RuleStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2 | Tableaclv6L3RuleTable | not-accessible | current | A table to configure L3 filter rules in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1 | Rowaclv6L3RuleEntry | not-accessible | current | Each entry in this table is a L3 filter rule. Index to the table is L3 filter number and Profile ID. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.1 | Columnaclv6L3RuleAccessID | read-only | current | L3 Filter rule ID. 0 means auto assign. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.2 | Columnaclv6L3RuleProfileNo | read-only | current | The Profile ID which this rule join. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.3 | Columnaclv6L3RuleProtocol | read-write | current | The type of protocol to be checked against the packet. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.4 | Columnaclv6L3RuleProtocolMask | read-only | current | The IP protocol mask. This field is read-only and copy from it's Profile setting. It will work with the other field,aclL3RuleProtocol, to caculate a range of I… |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.5 | Columnaclv6L3RuleICMPMessageType | read-write | current | The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action s… |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.6 | Columnaclv6L3RuleICMPMessageCode | read-write | current | The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action s… |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.7 | Columnaclv6L3RuleDstIpAddr | read-write | current | Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.8 | Columnaclv6L3RuleSrcIpAddr | read-write | current | Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.9 | Columnaclv6L3RuleDstIpAddrMask | read-only | current | The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.10 | Columnaclv6L3RuleSrcIpAddrMask | read-only | current | The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.11 | Columnaclv6L3RuleTcpUdpDstPort | read-write | current | The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.12 | Columnaclv6L3RuleTcpUdpSrcPort | read-write | current | The TCP / UDP source port. The default value is -1, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.13 | Columnaclv6L3RuleTcpUdpDstPortMask | read-only | current | The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.14 | Columnaclv6L3RuleTcpUdpSrcPortMask | read-only | current | The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.15 | Columnaclv6L3RuleTcpAckBit | read-create | current | The TCP ACK bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.16 | Columnaclv6L3RuleTcpRstBit | read-create | current | The TCP RST bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.17 | Columnaclv6L3RuleTcpUrgBit | read-create | current | The TCP Urg bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.18 | Columnaclv6L3RuleTcpPshBit | read-create | current | The TCP Psh bit to be checked against the packet. The default value is 'dont_care'(-1). which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.19 | Columnaclv6L3RuleTcpSynBit | read-create | current | The TCP Syn bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.20 | Columnaclv6L3RuleTcpFinBit | read-create | current | The TCP Fin bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.21 | Columnaclv6L3RuleTrafficClass | read-create | current | The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.23 | Columnaclv6L3RulePortList | read-write | current | Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.24 | Columnaclv6L3RuleAction | read-write | current | Specifies the action to be taken on the packet if the filter rule matches. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.25 | Columnaclv6L3RuleRateLimit | read-write | current | Rate limit for matched packet. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.26 | Columnaclv6L3RuleReplaceDSCP | read-write | current | ReplaceDSCP for matched packet. |
| 1.3.6.1.4.1.171.10.134.1.1.15.3.2.1.28 | Columnaclv6L3RuleStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.134.1.1.16 | NodecompanySyslog | |||
| 1.3.6.1.4.1.171.10.134.1.1.16.1 | NodesyslogSettingGroup | |||
| 1.3.6.1.4.1.171.10.134.1.1.16.1.1 | ScalarsyslogEnable | read-write | current | This object is for enabling or disabling syslog alert features in the system and the syslog will save to flash or send to remote syslog server. System Logs rec… |
| 1.3.6.1.4.1.171.10.134.1.1.16.1.2 | ScalarsyslogSaveMode | read-write | current | This object is for choosing the method to save syslog into flash. |
| 1.3.6.1.4.1.171.10.134.1.1.16.1.3 | ScalarsyslogSaveMinutes | read-write | current | When savemode is time interval, it's used to set the interval minutes of system save syslog to flash. |
| 1.3.6.1.4.1.171.10.134.1.1.16.3 | NodesyslogServerGroup | |||
| 1.3.6.1.4.1.171.10.134.1.1.16.3.1 | TablesyslogServTable | not-accessible | current | The table of syslog remote server. |
| 1.3.6.1.4.1.171.10.134.1.1.16.3.1.1 | RowsyslogServEntry | not-accessible | current | The list of syslog remote server entry. |
| 1.3.6.1.4.1.171.10.134.1.1.16.3.1.1.1 | ColumnsyslogServIndex | read-only | current | The index of syslog remote server. |
| 1.3.6.1.4.1.171.10.134.1.1.16.3.1.1.2 | ColumnsyslogServAddrType | read-create | current | Specifies the Address type of server.Address type shall be ipv4 or ipv6. |
| 1.3.6.1.4.1.171.10.134.1.1.16.3.1.1.3 | ColumnsyslogServAddr | read-create | current | Specifies the ServerIP to which the syslog shall be forwarded. |
| 1.3.6.1.4.1.171.10.134.1.1.16.3.1.1.4 | ColumnsyslogServInterfaceName | read-create | current | Specifies the interface name when the syslogServInterfaceName is linklocal address. |
| 1.3.6.1.4.1.171.10.134.1.1.16.3.1.1.5 | ColumnsyslogServSeverity | read-create | current | Specifies the log level option to be set for a specific server. |
| 1.3.6.1.4.1.171.10.134.1.1.16.3.1.1.6 | ColumnsyslogServFacility | read-create | current | The Syslog standard facilities. The facility to be used when sending Syslog messages to this server. |
| 1.3.6.1.4.1.171.10.134.1.1.16.3.1.1.7 | ColumnsyslogServUDPport | read-create | current | The value is for setting UDP Port. |
| 1.3.6.1.4.1.171.10.134.1.1.16.3.1.1.8 | ColumnsyslogServSrvStatus | read-write | current | The status for this server. If enable, system will send message to this server. |
| 1.3.6.1.4.1.171.10.134.1.1.16.3.1.1.9 | ColumnsyslogServSrvRowStatus | read-write | current | Row status of this server entry. |
| 1.3.6.1.4.1.171.10.134.1.1.17 | NodecompanyLBD | |||
| 1.3.6.1.4.1.171.10.134.1.1.17.1 | ScalarsysLBDStateEnable | read-write | current | Enable/Disable Loopback detection function. The Loopback Detection function is used to detect the loop created by a specific port while Spanning Tree Protocol … |
| 1.3.6.1.4.1.171.10.134.1.1.17.2 | ScalarsysLBDMode | read-write | current | Loopback detection function mode. |
| 1.3.6.1.4.1.171.10.134.1.1.17.3 | ScalarsysLBDInterval | read-write | current | Set a Loop detection Interval between 1 and 32767 seconds. The default is 2 seconds. This time interval to be used at counting time seconds to resend the CTP p… |
| 1.3.6.1.4.1.171.10.134.1.1.17.4 | ScalarsysLBDRecoverTime | read-write | current | This time interval to be used at counting time seconds to recover the disabled port automatically. The Loop Detection Recover Time can be set at 0 seconds, or … |
| 1.3.6.1.4.1.171.10.134.1.1.17.5 | TablesysLBDCtrlTable | not-accessible | current | A table to control Loopback detection features either for the entire switch or for each interface in the switch. |
| 1.3.6.1.4.1.171.10.134.1.1.17.5.1 | RowsysLBDCtrlEntry | not-accessible | current | An entry appears in this table for each interface in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.17.5.1.1 | ColumnsysLBDCtrlIndex | read-only | current | The interface index of the port for which the configuration in this entry applies. For all machines give maximum port number. |
| 1.3.6.1.4.1.171.10.134.1.1.17.5.1.2 | ColumnsysLBDPortStatus | read-write | current | Provides control to per port enable or disable the loopback detection function. Default is disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.17.5.1.3 | ColumnsysLBDPortLoopStatus | read-only | current | The loop status for this port. |
| 1.3.6.1.4.1.171.10.134.1.1.17.6 | TablesysLBDVlanLoopTable | not-accessible | current | A table to display Loopback detection features by vlan mode . |
| 1.3.6.1.4.1.171.10.134.1.1.17.6.1 | RowsysLBDVlanLoopEntry | not-accessible | current | An entry appears in this table for each interface in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.17.6.1.1 | ColumnsysLBDVlanLoopIndex | read-only | current | Display port lists loop status by vlan. |
| 1.3.6.1.4.1.171.10.134.1.1.17.6.1.2 | ColumnsysLBDVlanLoopPorts | read-only | current | Display port lists loop status by vlan. |
| 1.3.6.1.4.1.171.10.134.1.1.18 | NodecompanyMirror | |||
| 1.3.6.1.4.1.171.10.134.1.1.18.1 | ScalarsysMirrorStatus | read-write | current | Enable/Disable Port Mirroring function. Default is disabled. Port Mirroring is a method of monitoring network traffic that forwards a copy of each incoming and… |
| 1.3.6.1.4.1.171.10.134.1.1.18.2 | ScalarsysMirrorTargetPort | read-write | current | Specifies the port to which the mirrored traffic in the system is to be copied. |
| 1.3.6.1.4.1.171.10.134.1.1.18.3 | ScalarsysMirrorCtrlIngressMirroring | read-write | current | Provides control to enable or disable mirroring of ingress traffic over this interface to the mirrored-to port. |
| 1.3.6.1.4.1.171.10.134.1.1.18.4 | ScalarsysMirrorCtrlEgressMirroring | read-write | current | Provides control to enable or disable mirroring of egress traffic over this interface to the mirrored-to port. |
| 1.3.6.1.4.1.171.10.134.1.1.19 | NodecompanyStaticMcast | |||
| 1.3.6.1.4.1.171.10.134.1.1.19.1 | TablestaticMcastTable | not-accessible | current | A list of the Static MACs |
| 1.3.6.1.4.1.171.10.134.1.1.19.1.1 | RowstaticMcastEntry | not-accessible | current | A Static MAC entry containing the mac and forwarding port. |
| 1.3.6.1.4.1.171.10.134.1.1.19.1.1.1 | ColumnstaticMcastVlanID | read-only | current | The VLAN ID of the static MAC entry. |
| 1.3.6.1.4.1.171.10.134.1.1.19.1.1.2 | ColumnstaticMcastMac | read-only | current | The MAC address associated of the static MAC entry. |
| 1.3.6.1.4.1.171.10.134.1.1.19.1.1.3 | ColumnstaticMcastEgressPorts | read-only | current | The set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast MAC address must be forwarded, regardless of … |
| 1.3.6.1.4.1.171.10.134.1.1.19.1.1.4 | ColumnstaticMcastIpAddr | read-only | current | Static Multicast IP Address. |
| 1.3.6.1.4.1.171.10.134.1.1.19.1.1.5 | ColumnstaticMcastStatus | read-write | current | The status of an entry in the Static Mcast Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
| 1.3.6.1.4.1.171.10.134.1.1.20 | NodecompanySNTPSetting | |||
| 1.3.6.1.4.1.171.10.134.1.1.20.17 | NodesysSNTPServerTable | |||
| 1.3.6.1.4.1.171.10.134.1.1.20.17.1 | ScalarsysSNTPTimeSeconds | read-write | current | This object is for setting the system time in seconds from Epoch (00:00:00 UTC, January 1, 2009). Notice : input value must larger than 1230768000 (00:00:00 UT… |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.2 | ScalarsysSNTPFirstServer | read-write | current | SNTP First Server's IPv6 Address |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.3 | ScalarsysSNTPFirstType | read-write | current | SNTP First Server's IPv6 Address type. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.4 | ScalarsysSNTPFirstInterfaceName | read-write | current | Specifies the interface name when the sysSNTPFirstServer is linklocal address. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.5 | ScalarsysSNTPSecondServer | read-write | current | SNTP Second Server's IPv6 Address |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.6 | ScalarsysSNTPSecondType | read-write | current | SNTP First Server's IPv6 Address type. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.7 | ScalarsysSNTPSecondInterfaceName | read-write | current | Specifies the interface name when the sysSNTPSecondServer is linklocal address. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.8 | ScalarsysSNTPPollInterval | read-write | current | SNTP Poll Interval In Seconds (30-99999) |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.9 | ScalarsysSNTPState | read-write | current | Enable/Disable SNTP function in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.10 | ScalarsysSNTPDSTOffset | read-write | current | This object is for Daylight Saving Time Offset In (30/60/90/120) Minutes. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.11 | ScalarsysSNTPGMTMinutes | read-write | current | Specifies the Time Zone Offset from GMT in +/- Minutes. (+780 ~ -720) |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.12 | ScalarsysSNTPDSTStartMon | read-write | current | The start month of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.13 | ScalarsysSNTPDSTStartDay | read-write | current | The start day of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.14 | ScalarsysSNTPDSTStartHour | read-write | current | The start hour of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.15 | ScalarsysSNTPDSTStartMin | read-write | current | The start minute of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.16 | ScalarsysSNTPDSTEndMon | read-write | current | The end month of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.17 | ScalarsysSNTPDSTEndDay | read-write | current | The end day of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.18 | ScalarsysSNTPDSTEndHour | read-write | current | The end hour of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.19 | ScalarsysSNTPDSTEndMin | read-write | current | The end minute of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.20 | ScalarsysSNTPDSTState | read-write | current | This object is for Enabled(1) or Disabled(2) DST state in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.30 | ScalarsysSNTPDSTMethod | read-write | current | This object is for Annual(1) or Repeating(2) DST method in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.31 | ScalarsysSNTPDSTRepeatStartMon | read-write | current | The start month of Daylight Saving Time in Repeating mode. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.32 | ScalarsysSNTPDSTRepeatStartWeek | read-write | current | The start week of Daylight Saving Time in Repeating mode. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.33 | ScalarsysSNTPDSTRepeatStartWeekDay | read-write | current | The start weekday of Daylight Saving Time in Repeating mode. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.34 | ScalarsysSNTPDSTRepeatStartHour | read-write | current | The start hour of Daylight Saving Time in Repeating mode.. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.35 | ScalarsysSNTPDSTRepeatStartMin | read-write | current | The start minute of Daylight Saving Time in Repeating mode. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.36 | ScalarsysSNTPDSTRepeatEndMon | read-write | current | The end month of Daylight Saving Time in Repeating mode. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.37 | ScalarsysSNTPDSTRepeatEndWeek | read-write | current | The end week of Daylight Saving Time in Repeating mode. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.38 | ScalarsysSNTPDSTRepeatEndWeekDay | read-write | current | The end weekday of Daylight Saving Time in Repeating mode. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.39 | ScalarsysSNTPDSTRepeatEndHour | read-write | current | The end hour of Daylight Saving Time in Repeating mode.. |
| 1.3.6.1.4.1.171.10.134.1.1.20.17.40 | ScalarsysSNTPDSTRepeatEndMin | read-write | current | The end minute of Daylight Saving Time in Repeating mode. |
| 1.3.6.1.4.1.171.10.134.1.1.22 | NodecompanyRMON | |||
| 1.3.6.1.4.1.171.10.134.1.1.22.1 | ScalarrmonGlobalState | read-write | current | This object is for enabling or disabling RMON function. |
| 1.3.6.1.4.1.171.10.134.1.1.22.2 | NodermonStatistics | |||
| 1.3.6.1.4.1.171.10.134.1.1.22.2.1 | TablermonStatsTable | not-accessible | current | A list of Ethernet statistics entries. |
| 1.3.6.1.4.1.171.10.134.1.1.22.2.1.1 | RowrmonStatsEntry | not-accessible | current | A collection of statistics kept for a particular Ethernet interface. As an example, an instance of the etherStatsPkts object might be named etherStatsPkts.1 |
| 1.3.6.1.4.1.171.10.134.1.1.22.2.1.1.1 | ColumnrmonStatsIndex | read-only | current | The value of this object uniquely identifies this etherStats entry. |
| 1.3.6.1.4.1.171.10.134.1.1.22.2.1.1.2 | ColumnrmonStatsDataSource | read-create | current | This object identifies the source of the data that this etherStats entry is configured to analyze. This source can be any ethernet interface on this device. In… |
| 1.3.6.1.4.1.171.10.134.1.1.22.2.1.1.3 | ColumnrmonStatsOwner | read-create | current | The entity that configured this entry and is therefore using the resources assigned to it. |
| 1.3.6.1.4.1.171.10.134.1.1.22.2.1.1.4 | ColumnrmonStatsStatus | read-create | current | The status of this etherStats entry. |
| 1.3.6.1.4.1.171.10.134.1.1.22.3 | NodermonHistory | |||
| 1.3.6.1.4.1.171.10.134.1.1.22.3.1 | TablermonHistoryTable | not-accessible | current | A list of history control entries. |
| 1.3.6.1.4.1.171.10.134.1.1.22.3.1.1 | RowrmonHistoryEntry | not-accessible | current | A list of parameters that set up a periodic sampling of statistics. As an example, an instance of the historyControlInterval object might be named historyContr… |
| 1.3.6.1.4.1.171.10.134.1.1.22.3.1.1.1 | ColumnrmonHistoryIndex | read-only | current | An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on t… |
| 1.3.6.1.4.1.171.10.134.1.1.22.3.1.1.2 | ColumnrmonHistoryDataSource | read-create | current | This object identifies the source of the data for which historical data was collected and placed in a media-specific table on behalf of this historyControlEntr… |
| 1.3.6.1.4.1.171.10.134.1.1.22.3.1.1.3 | ColumnrmonHistoryBucketsRequested | read-create | current | The requested number of discrete time intervals over which data is to be saved in the part of the media-specific table associated with this historyControlEntry… |
| 1.3.6.1.4.1.171.10.134.1.1.22.3.1.1.4 | ColumnrmonHistoryInterval | read-create | current | The interval in seconds over which the data is sampled for each bucket in the part of the media-specific table associated with this historyControlEntry. This i… |
| 1.3.6.1.4.1.171.10.134.1.1.22.3.1.1.5 | ColumnrmonHistoryOwner | read-create | current | The entity that configured this entry and is therefore using the resources assigned to it. |
| 1.3.6.1.4.1.171.10.134.1.1.22.3.1.1.6 | ColumnrmonHistoryStatus | read-create | current | The status of this historyControl entry. Each instance of the media-specific table associated with this historyControlEntry will be deleted by the agent if thi… |
| 1.3.6.1.4.1.171.10.134.1.1.22.4 | NodermonAlarm | |||
| 1.3.6.1.4.1.171.10.134.1.1.22.4.1 | TablermonAlarmTable | not-accessible | current | A list of alarm entries. |
| 1.3.6.1.4.1.171.10.134.1.1.22.4.1.1 | RowrmonAlarmEntry | not-accessible | current | A list of parameters that set up a periodic checking for alarm conditions. For example, an instance of the alarmValue object might be named alarmValue.8 |
| 1.3.6.1.4.1.171.10.134.1.1.22.4.1.1.1 | ColumnrmonAlarmIndex | read-only | current | An index that uniquely identifies an entry in the alarm table. Each such entry defines a diagnostic sample at a particular interval for an object on the device. |
| 1.3.6.1.4.1.171.10.134.1.1.22.4.1.1.2 | ColumnrmonAlarmInterval | read-create | current | The interval in seconds over which the data is sampled and compared with the rising and falling thresholds. When setting this variable, care should be taken in… |
| 1.3.6.1.4.1.171.10.134.1.1.22.4.1.1.3 | ColumnrmonAlarmVariable | read-create | current | The object identifier of the particular variable to be sampled. Only variables that resolve to an ASN.1 primitive type of INTEGER (INTEGER, Integer32, Counter3… |
| 1.3.6.1.4.1.171.10.134.1.1.22.4.1.1.4 | ColumnrmonAlarmSampleType | read-create | current | The method of sampling the selected variable and calculating the value to be compared against the thresholds. If the value of this object is absoluteValue(1), … |
| 1.3.6.1.4.1.171.10.134.1.1.22.4.1.1.5 | ColumnrmonAlarmRisingThreshold | read-create | current | A threshold for the sampled statistic. When the current sampled value is greater than or equal to this threshold, and the value at the last sampling interval w… |
| 1.3.6.1.4.1.171.10.134.1.1.22.4.1.1.6 | ColumnrmonAlarmFallingThreshold | read-create | current | A threshold for the sampled statistic. When the current sampled value is less than or equal to this threshold, and the value at the last sampling interval was … |
| 1.3.6.1.4.1.171.10.134.1.1.22.4.1.1.7 | ColumnrmonAlarmRisingEventIndex | read-create | current | The index of the eventEntry that is used when a rising threshold is crossed. The eventEntry identified by a particular value of this index is the same as ident… |
| 1.3.6.1.4.1.171.10.134.1.1.22.4.1.1.8 | ColumnrmonAlarmFallingEventIndex | read-create | current | The index of the eventEntry that is used when a falling threshold is crossed. The eventEntry identified by a particular value of this index is the same as iden… |
| 1.3.6.1.4.1.171.10.134.1.1.22.4.1.1.9 | ColumnrmonAlarmOwner | read-create | current | The entity that configured this entry and is therefore using the resources assigned to it. |
| 1.3.6.1.4.1.171.10.134.1.1.22.4.1.1.10 | ColumnrmonAlarmStatus | read-create | current | The status of this alarm entry. |
| 1.3.6.1.4.1.171.10.134.1.1.22.5 | NodermonEvent | |||
| 1.3.6.1.4.1.171.10.134.1.1.22.5.1 | TablermonEventTable | not-accessible | current | A list of events to be generated. |
| 1.3.6.1.4.1.171.10.134.1.1.22.5.1.1 | RowrmonEventEntry | not-accessible | current | A set of parameters that describe an event to be generated when certain conditions are met. As an example, an instance of the eventLastTimeSent object might be… |
| 1.3.6.1.4.1.171.10.134.1.1.22.5.1.1.1 | ColumnrmonEventIndex | read-only | current | An index that uniquely identifies an entry in the event table. Each such entry defines one event that is to be generated when the appropriate conditions occur. |
| 1.3.6.1.4.1.171.10.134.1.1.22.5.1.1.2 | ColumnrmonEventDescription | read-create | current | A comment describing this event entry. |
| 1.3.6.1.4.1.171.10.134.1.1.22.5.1.1.3 | ColumnrmonEventType | read-create | current | The type of notification that the probe will make about this event. In the case of log, an entry is made in the log table for each event. In the case of snmp-t… |
| 1.3.6.1.4.1.171.10.134.1.1.22.5.1.1.4 | ColumnrmonEventCommunity | read-create | current | If an SNMP trap is to be sent, it will be sent to the SNMP community specified by this octet string. |
| 1.3.6.1.4.1.171.10.134.1.1.22.5.1.1.5 | ColumnrmonEventOwner | read-create | current | The entity that configured this entry and is therefore using the resources assigned to it. If this object contains a string starting with 'monitor' and has ass… |
| 1.3.6.1.4.1.171.10.134.1.1.22.5.1.1.6 | ColumnrmonEventStatus | read-create | current | The status of this event entry. If this object is not equal to valid(1), all associated log entries shall be deleted by the agent. |
| 1.3.6.1.4.1.171.10.134.1.1.23 | NodecompanyAuthGroup | |||
| 1.3.6.1.4.1.171.10.134.1.1.23.1 | NodeswAuthenCtrl | |||
| 1.3.6.1.4.1.171.10.134.1.1.23.1.1 | ScalarswAuthStatus | read-write | current | Enable/Disable Static 802.1x. |
| 1.3.6.1.4.1.171.10.134.1.1.23.1.2 | ScalarswAuthMode | read-write | current | This object indicates the authentication mode of the device. |
| 1.3.6.1.4.1.171.10.134.1.1.23.1.3 | ScalarauthProtocol | read-write | current | The authentication method used to authenticate users. |
| 1.3.6.1.4.1.171.10.134.1.1.23.1.4 | ScalarswAuthCtrlPktFwdMode | read-write | current | When 802.1x disable, this item can decided eap packet be forward or drop. |
| 1.3.6.1.4.1.171.10.134.1.1.23.2 | NodeswAuthPortAccessCtrl | |||
| 1.3.6.1.4.1.171.10.134.1.1.23.2.1 | TableswAuthPortAccessControlTable | not-accessible | current | A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may auth… |
| 1.3.6.1.4.1.171.10.134.1.1.23.2.1.1 | RowswAuthPortAccessControlEntry | not-accessible | current | The configuration information for an Authenticator Port. |
| 1.3.6.1.4.1.171.10.134.1.1.23.2.1.1.1 | ColumnswAuthAuthConfigPortNumber | read-only | current | A unique value for each port that correlates to port index. Its value ranges between 1 and the value of port number. For all machines give maximum port number. |
| 1.3.6.1.4.1.171.10.134.1.1.23.2.1.1.2 | ColumnswAuthAuthQuietPeriod | read-write | current | The value, in seconds, of the quietPeriod constant currently in use by the Authenticator PAE state machine. |
| 1.3.6.1.4.1.171.10.134.1.1.23.2.1.1.3 | ColumnswAuthAuthSuppTimeout | read-write | current | The value, in seconds, of the suppTimeout constant currently in use by the Backend Authentication state machine. |
| 1.3.6.1.4.1.171.10.134.1.1.23.2.1.1.4 | ColumnswAuthAuthServerTimeout | read-write | current | The value, in seconds, of the serverTimeout constant currently in use by the Backend Authentication state machine. |
| 1.3.6.1.4.1.171.10.134.1.1.23.2.1.1.5 | ColumnswAuthAuthMaxReq | read-write | current | The value of the maxReq constant currently in use by the Backend Authentication state machine. |
| 1.3.6.1.4.1.171.10.134.1.1.23.2.1.1.6 | ColumnswAuthAuthTxPeriod | read-write | current | The value, in seconds, of the txPeriod constant currently in use by the Authenticator PAE state machine. |
| 1.3.6.1.4.1.171.10.134.1.1.23.2.1.1.7 | ColumnswAuthAuthReAuthPeriod | read-write | current | The value, in seconds, of the reAuthPeriod constant currently in use by the Reauthentication Timer state machine. |
| 1.3.6.1.4.1.171.10.134.1.1.23.2.1.1.8 | ColumnswAuthAuthReAuthentication | read-write | current | The enable/disable control used by the Reauthentication Timer state machine (8.5.5.1). |
| 1.3.6.1.4.1.171.10.134.1.1.23.2.1.1.9 | ColumnswAuthAuthConfigPortControl | read-write | current | The current value of the controlled Port control parameter for the Port. |
| 1.3.6.1.4.1.171.10.134.1.1.23.2.1.1.10 | ColumnswAuthAuthCapability | read-write | current | The current value of the controlled Port control parameter for the Port. |
| 1.3.6.1.4.1.171.10.134.1.1.23.2.1.1.11 | ColumnswAuthAuthDirection | read-write | current | The current value of the controlled Port control parameter for the Port. |
| 1.3.6.1.4.1.171.10.134.1.1.23.3 | NodeswAuthUser | |||
| 1.3.6.1.4.1.171.10.134.1.1.23.3.1 | TableswAuthUserTable | not-accessible | current | A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may auth… |
| 1.3.6.1.4.1.171.10.134.1.1.23.3.1.1 | RowswAuthUserEntry | not-accessible | current | The configuration information for an Authenticator Port. |
| 1.3.6.1.4.1.171.10.134.1.1.23.3.1.1.1 | ColumnswAuthUserName | read-only | current | The unique index value of a row in this table. This object is used to set 802.1X Local user name, The following characters are allowed to input: semicolon, que… |
| 1.3.6.1.4.1.171.10.134.1.1.23.3.1.1.2 | ColumnswAuthUserPassword | read-write | current | This object is used to set 802.1X Local user Password, The following characters are allowed to input: semicolon, question mark, space, and double quotation mar… |
| 1.3.6.1.4.1.171.10.134.1.1.23.3.1.1.3 | ColumnswAuthUserStatus | read-create | current | The status of this conceptual row in the swAuthUserTable. An entry in this table is not qualified for activation until instances of all corresponding columns h… |
| 1.3.6.1.4.1.171.10.134.1.1.23.4 | NodeswAuthRadiusServer | |||
| 1.3.6.1.4.1.171.10.134.1.1.23.4.2 | TableswAuthRadiusServerTable | not-accessible | current | A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may auth… |
| 1.3.6.1.4.1.171.10.134.1.1.23.4.2.1 | RowswAuthRadiusServerEntry | not-accessible | current | The configuration information for an Authenticator Port. |
| 1.3.6.1.4.1.171.10.134.1.1.23.4.2.1.1 | ColumnswAuthRadiusServerIndex | read-only | current | A unique value for Authentication RADIUS Server index. Its value ranges between 1 and 3. |
| 1.3.6.1.4.1.171.10.134.1.1.23.4.2.1.2 | ColumnswAuthRadiusIPType | read-write | current | The IP address of the RADIUS server IP type referred to in this table entry. |
| 1.3.6.1.4.1.171.10.134.1.1.23.4.2.1.3 | ColumnswAuthRadiusServerAddress | read-write | current | The IP address of the RADIUS server referred to in this table entry. |
| 1.3.6.1.4.1.171.10.134.1.1.23.4.2.1.4 | ColumnswAuthRadiusServerInterfaceName | read-create | current | Specifies the interface name when the swAuthRadiusServerAddress is linklocal address. |
| 1.3.6.1.4.1.171.10.134.1.1.23.4.2.1.5 | ColumnswAuthRadiusServerAuthenticationPort | read-write | current | The value is for setting UDP Port. |
| 1.3.6.1.4.1.171.10.134.1.1.23.4.2.1.6 | ColumnswAuthRadiusServerAccountingPort | read-write | current | The value is for setting UDP Port. |
| 1.3.6.1.4.1.171.10.134.1.1.23.4.2.1.7 | ColumnswAuthRadiusServerTimeout | read-write | current | The value is for setting UDP Port. |
| 1.3.6.1.4.1.171.10.134.1.1.23.4.2.1.8 | ColumnswAuthRadiusServerRetransmit | read-write | current | The value is for setting UDP Port. |
| 1.3.6.1.4.1.171.10.134.1.1.23.4.2.1.9 | ColumnswAuthRadiusServerKey | read-write | current | This object is used to set 802.1X Radius Server Key, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark. |
| 1.3.6.1.4.1.171.10.134.1.1.23.4.2.1.10 | ColumnswAuthRadiusServerStatus | read-create | current | The status of this conceptual row in the swAuthRadiusServerTable. An entry in this table is not qualified for activation until instances of all corresponding c… |
| 1.3.6.1.4.1.171.10.134.1.1.24 | NodecompanyGuestVlan | |||
| 1.3.6.1.4.1.171.10.134.1.1.24.1 | ScalarguestVlanName | read-write | current | The VLAN name of guest VLAN. |
| 1.3.6.1.4.1.171.10.134.1.1.24.2 | ScalarguestVlanPort | read-write | current | This object indicates the guest VLAN port members of this device. |
| 1.3.6.1.4.1.171.10.134.1.1.24.3 | ScalarguestVlanDelState | read-write | current | Used to delete the guest VLAN. |
| 1.3.6.1.4.1.171.10.134.1.1.25 | NodecompanyMacNotify | |||
| 1.3.6.1.4.1.171.10.134.1.1.25.1 | ScalarmacNotifyState | read-write | current | This object can enabled or disabled MAC Notification. |
| 1.3.6.1.4.1.171.10.134.1.1.25.2 | ScalarmacNotifyInterval | read-write | current | This object indicates the time interval in second for trigger the MAC notify message. |
| 1.3.6.1.4.1.171.10.134.1.1.25.3 | ScalarmacNotifyHistorySize | read-write | current | This object indicates the history size of variation MAC in address table. The default value is 1 . |
| 1.3.6.1.4.1.171.10.134.1.1.25.4 | TablemacNotifyCtrlTable | not-accessible | current | A table to control Loopback detection features either for the entire switch or for each interface in the switch. |
| 1.3.6.1.4.1.171.10.134.1.1.25.4.1 | RowmacNotifyCtrlEntry | not-accessible | current | An entry appears in this table for each interface in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.25.4.1.1 | ColumnmacNotifyCtrlIndex | read-only | current | The interface index of the port for which the configuration in this entry applies. For all machines give maximum port number. |
| 1.3.6.1.4.1.171.10.134.1.1.25.4.1.2 | ColumnmacNotifyPortStatus | read-write | current | Provides control to per port enable or disable the loopback detection function. Default is disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.25.5 | NodemacNotifyInfo | |||
| 1.3.6.1.4.1.171.10.134.1.1.25.5.1 | ScalarmacNotifyInfoDiscription | accessible-for-notify | current | This object indicates the information for the device MAC address changes. And the detailed information include: Operation Code + MAC address + Box ID + Port Nu… |
| 1.3.6.1.4.1.171.10.134.1.1.27 | NodecompanyISMVLAN | |||
| 1.3.6.1.4.1.171.10.134.1.1.27.1 | ScalarigmpMulticastVlanStatus | read-write | current | Enable/Disable IGMP Multicast Vlan function. |
| 1.3.6.1.4.1.171.10.134.1.1.27.4 | TablemulticastVlanTable | not-accessible | current | Information about the IGMP/MLD snooping multicast VLAN table. |
| 1.3.6.1.4.1.171.10.134.1.1.27.4.1 | RowmulticastVlanEntry | not-accessible | current | The entry of multicastVlanTable. |
| 1.3.6.1.4.1.171.10.134.1.1.27.4.1.1 | ColumnmulticastVlanid | read-only | current | This object indicates the VLAN ID of the IGMP/MLD snooping multicast VLAN entry. |
| 1.3.6.1.4.1.171.10.134.1.1.27.4.1.2 | ColumnmulticastVlanName | read-create | current | This object indicates the VLAN name of the IGMP/MLD snooping multicast VLAN entry. |
| 1.3.6.1.4.1.171.10.134.1.1.27.4.1.3 | ColumnmulticastVlanSourcePort | read-write | current | This object indicates the port list of the source ports of the IGMP/MLD snooping multicast VLAN. The source ports will be set as tag ports of the VLAN entry an… |
| 1.3.6.1.4.1.171.10.134.1.1.27.4.1.4 | ColumnmulticastVlanMemberPort | read-write | current | This object indicates the port list of the member ports of the IGMP/MLD snooping multicast VLAN. The source ports will be set as untagged ports of the VLAN ent… |
| 1.3.6.1.4.1.171.10.134.1.1.27.4.1.5 | ColumnmulticastVlanTagMemberPort | read-write | current | This object indicates the port list of the tag member ports of the IGMP/MLD snooping multicast VLAN. |
| 1.3.6.1.4.1.171.10.134.1.1.27.4.1.6 | ColumnmulticastVlanState | read-write | current | This object can be used to enable or disable the IGMP/MLD snooping multicast VLAN. |
| 1.3.6.1.4.1.171.10.134.1.1.27.4.1.7 | ColumnmulticastVlanIgmpReplaceSourceIp | read-write | current | The replacement source IP of this IGMP snooping multicast VLAN. |
| 1.3.6.1.4.1.171.10.134.1.1.27.4.1.8 | ColumnmulticastVlanMldReplaceSourceIp | read-write | current | The replacement source IP of this MLD snooping multicast VLAN. |
| 1.3.6.1.4.1.171.10.134.1.1.27.4.1.9 | ColumnmulticastVlanRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.10.134.1.1.27.5 | TablemulticastVlanGroupTable | not-accessible | current | The table containing the IGMP/MLD snooping multicast VLAN group information |
| 1.3.6.1.4.1.171.10.134.1.1.27.5.1 | RowmulticastVlanGroupEntry | not-accessible | current | The entry of multicastVlanGroupTable. |
| 1.3.6.1.4.1.171.10.134.1.1.27.5.1.1 | ColumnmulticastVlanGroupVid | read-only | current | This object indicates the VID of the IGMP/MLD snooping multicast VLAN group. |
| 1.3.6.1.4.1.171.10.134.1.1.27.5.1.2 | ColumnmulticastVlanGroupIpType | read-only | current | Type of specifies the multicast address list for this VLAN. |
| 1.3.6.1.4.1.171.10.134.1.1.27.5.1.3 | ColumnmulticastVlanGroupFromIp | read-only | current | Specifies the multicast address list for this VLAN. |
| 1.3.6.1.4.1.171.10.134.1.1.27.5.1.4 | ColumnmulticastVlanGroupToIp | read-only | current | Specifies the multicast address list for this VLAN. |
| 1.3.6.1.4.1.171.10.134.1.1.27.5.1.5 | ColumnmulticastVlanGroupStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.10.134.1.1.28 | NodecompanyDHCPRelay | |||
| 1.3.6.1.4.1.171.10.134.1.1.28.1 | NodedhcpBOOTPRelayControl | |||
| 1.3.6.1.4.1.171.10.134.1.1.28.1.1 | ScalardhcpBOOTPRelayState | read-write | current | This object indicates DHCP relay function is enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.28.1.2 | ScalardhcpBOOTPRelayHopCount | read-write | current | This object indicates the maximum number of router hops that the BOOTP packets can cross. |
| 1.3.6.1.4.1.171.10.134.1.1.28.1.3 | ScalardhcpBOOTPRelayTimeThreshold | read-write | current | This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP … |
| 1.3.6.1.4.1.171.10.134.1.1.28.1.4 | ScalardhcpBOOTPRelayEnablePortlist | read-write | current | This object indicates DHCP relay function is enabled or disabled by portlist. |
| 1.3.6.1.4.1.171.10.134.1.1.28.1.5 | TabledhcpRelayVlanTable | not-accessible | current | This table indicates the IP address as a destination to forward (relay) DHCP packets to. |
| 1.3.6.1.4.1.171.10.134.1.1.28.1.5.1 | RowdhcpRelayVlanTableEntry | not-accessible | current | A list of information indicates the IP address as a destination to forward (relay) DHCP packets to. |
| 1.3.6.1.4.1.171.10.134.1.1.28.1.5.1.1 | ColumndhcpRelayVlanSettingsVLANID | read-only | current | This object displays the current VLAN ID of the device. |
| 1.3.6.1.4.1.171.10.134.1.1.28.1.5.1.2 | ColumndhcpRelayVlanSettingsState | read-write | current | This object indicates DHCP relay function of VLAN is enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.28.2 | NodedhcpBOOTPRelayManagement | |||
| 1.3.6.1.4.1.171.10.134.1.1.28.2.1 | TabledhcpBOOTPRelayInterfaceSettingsTable | not-accessible | current | This table indicates the IP address as a destination to forward (relay) DHCP packets to. |
| 1.3.6.1.4.1.171.10.134.1.1.28.2.1.1 | RowdhcpBOOTPRelayInterfaceSettingsEntry | not-accessible | current | A list of information indicates the IP address as a destination to forward (relay) DHCP packets to. |
| 1.3.6.1.4.1.171.10.134.1.1.28.2.1.1.1 | ColumndhcpBOOTPRelayInterface | read-only | current | This object indicates the name of the IP interface. |
| 1.3.6.1.4.1.171.10.134.1.1.28.2.1.1.2 | ColumndhcpBOOTPRelayServerIP | read-only | current | This object indicates the DHCP server IP address. |
| 1.3.6.1.4.1.171.10.134.1.1.28.2.1.1.3 | ColumndhcpBOOTPRelayInterfaceSettingsRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.10.134.1.1.28.2.2 | NodedhcpBOOTPRelayManagementOption82 | |||
| 1.3.6.1.4.1.171.10.134.1.1.28.2.2.1 | ScalardhcpBOOTPRelayOption82State | read-write | current | This object indicates DHCP relay option 82 function is enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.28.2.2.2 | ScalardhcpBOOTPRelayOption82CheckState | read-write | current | This object indicates DHCP relay option 82 Check function is enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.28.2.2.3 | ScalardhcpBOOTPRelayOption82Policy | read-write | current | This object indicates DHCP relay option 82 policy. |
| 1.3.6.1.4.1.171.10.134.1.1.28.2.2.4 | ScalardhcpBOOTPRelayOption82RemoteIDType | read-write | current | This object indicates the type of remote ID. If the type is default, the remote ID will be the MAC address of the device, otherwise, the remote ID can be defin… |
| 1.3.6.1.4.1.171.10.134.1.1.28.2.2.5 | ScalardhcpBOOTPRelayOption82RemoteID | read-write | current | This object displays the current remote ID of the device. If swDHCPRelayOption82RemoteIDType is set to default, the value will be the MAC address of the device… |
| 1.3.6.1.4.1.171.10.134.1.1.29 | NodecompanyDHCPLocalRelay | |||
| 1.3.6.1.4.1.171.10.134.1.1.29.1 | ScalardhcpLocalRelayGlobalState | read-write | current | This object indicates DHCP local relay function of VLAN is enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.29.2 | TabledhcpLocalRelayTable | not-accessible | current | This table indicates the IP address as a destination to forward (local relay) DHCP packets to. |
| 1.3.6.1.4.1.171.10.134.1.1.29.2.1 | RowdhcpLocalRelayTableEntry | not-accessible | current | A list of information indicates the IP address as a destination to forward (local relay) DHCP packets to. |
| 1.3.6.1.4.1.171.10.134.1.1.29.2.1.1 | ColumndhcpLocalRelaySettingsVLANID | read-only | current | This object displays the current VLAN ID of the device. |
| 1.3.6.1.4.1.171.10.134.1.1.29.2.1.2 | ColumndhcpLocalRelaySettingsState | read-write | current | This object indicates DHCP local relay function of VLAN is enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.29.3 | ScalardhcpLocalRelayEnablePortlist | read-write | current | This object indicates DHCP local relay function is enabled or disabled by portlist. |
| 1.3.6.1.4.1.171.10.134.1.1.30 | NodecompanyTrapSetting | |||
| 1.3.6.1.4.1.171.10.134.1.1.30.1 | ScalarsysTrapIP | read-write | current | The smart console utility's IP address is used to recive trap events. |
| 1.3.6.1.4.1.171.10.134.1.1.30.2 | ScalarsysTrapSystemEvent | read-write | current | Enable/Disable system trap events in the switch system. |
| 1.3.6.1.4.1.171.10.134.1.1.30.3 | ScalarsysTrapFiberPortEvent | read-write | current | Enable/Disable fiber port trap event in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.30.4 | ScalarsysTrapTwistedPortEvent | read-write | current | Enable/Disable twisted port trap event in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.30.10 | ScalarsysTrapStatus | read-write | current | Enable/Disable trap event in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.30.13 | ScalarsysTrapPortSecurity | read-write | current | |
| 1.3.6.1.4.1.171.10.134.1.1.30.15 | ScalarsysTrapLBD | read-write | current | |
| 1.3.6.1.4.1.171.10.134.1.1.31 | NodecompanyGreenSetting | |||
| 1.3.6.1.4.1.171.10.134.1.1.31.1 | NodedlinkGreenLEDShutoff | |||
| 1.3.6.1.4.1.171.10.134.1.1.31.1.1 | ScalardlinkGreenLEDShutoffPortList | read-write | current | Provides control to disable LED port. |
| 1.3.6.1.4.1.171.10.134.1.1.31.1.2 | ScalardlinkGreenLEDShutoffState | read-write | current | Enable/Disable Green disable LED function. Default is disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.31.1.3 | ScalardlinkGreenLEDShutoffTimeProfile1 | read-write | current | The time profile name associated with the Schedule entry (e.g., `abc, bbb'). |
| 1.3.6.1.4.1.171.10.134.1.1.31.1.4 | ScalardlinkGreenLEDShutoffTimeProfile2 | read-write | current | The time profile name associated with the Schedule entry (e.g., `abc, bbb'). |
| 1.3.6.1.4.1.171.10.134.1.1.31.2 | NodedlinkGreenPortShutoff | |||
| 1.3.6.1.4.1.171.10.134.1.1.31.2.1 | ScalardlinkGreenPortShutoffPortList | read-write | current | Provides control to disable LED port. |
| 1.3.6.1.4.1.171.10.134.1.1.31.2.2 | ScalardlinkGreenPortShutoffState | read-write | current | Enable/Disable Green disable LED function. Default is disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.31.2.3 | ScalardlinkGreenPortShutoffTimeProfile1 | read-write | current | The time profile name associated with the Schedule entry (e.g., `abc, bbb'). |
| 1.3.6.1.4.1.171.10.134.1.1.31.2.4 | ScalardlinkGreenPortShutoffTimeProfile2 | read-write | current | The time profile name associated with the Schedule entry (e.g., `abc, bbb'). |
| 1.3.6.1.4.1.171.10.134.1.1.31.4 | NodedlinkGreenSystemHibernation | |||
| 1.3.6.1.4.1.171.10.134.1.1.31.4.1 | ScalardlinkGreenSystemHibernationState | read-write | current | Enable/Disable Green disable LED function. Default is disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.31.4.2 | ScalardlinkGreenSystemHibernationTimeProfile1 | read-write | current | The time profile name associated with the Schedule entry (e.g., `abc, bbb'). |
| 1.3.6.1.4.1.171.10.134.1.1.31.4.3 | ScalardlinkGreenSystemHibernationTimeProfile2 | read-write | current | The time profile name associated with the Schedule entry (e.g., `abc, bbb'). |
| 1.3.6.1.4.1.171.10.134.1.1.31.5 | ScalardlinkPowerSavCableLenDetectionState | read-write | current | Enable/Disable Power Saving Cable Length Detection. Default is enabled. |
| 1.3.6.1.4.1.171.10.134.1.1.32 | NodecompanyLLDPSetting | |||
| 1.3.6.1.4.1.171.10.134.1.1.32.1 | ScalardlinklldpState | read-write | current | This object is used for enabling or disabling LLDP in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.2 | ScalardlinklldpMsgHoldMultiplier | read-write | current | The time-to-live value expressed as a multiple of the lldpMessageTxInterval object.The actual time-to-live value used in LLDP frames, transmitted on behalf of … |
| 1.3.6.1.4.1.171.10.134.1.1.32.3 | ScalardlinklldpMsgTxInterval | read-write | current | This object is used for LLDP packet update frequency. The timer in units of seconds. |
| 1.3.6.1.4.1.171.10.134.1.1.32.4 | ScalardlinklldpReinitDelay | read-write | current | This object is used for LLDP Reinitialization Delay. The timer in units of seconds. |
| 1.3.6.1.4.1.171.10.134.1.1.32.5 | ScalardlinklldpTxDelay | read-write | current | The lldpTxDelay indicates the delay (in units of seconds) between successive LLDP frame transmissions initiated by value/status changes in the LLDP local syste… |
| 1.3.6.1.4.1.171.10.134.1.1.32.6 | ScalardlinklldpConfigManAddrPortsTxEnable | read-write | current | A set of ports that are identified by a PortList, in which each port is represented as a bit. The corresponding local system management address instance will b… |
| 1.3.6.1.4.1.171.10.134.1.1.32.11 | TablelldpPortConfigTable | not-accessible | current | The table that controls LLDP frame transmission on individual ports. |
| 1.3.6.1.4.1.171.10.134.1.1.32.11.1 | RowlldpPortConfigEntry | not-accessible | current | LLDP configuration information for a particular port. This configuration parameter controls the transmission and the reception of LLDP frames on those ports wh… |
| 1.3.6.1.4.1.171.10.134.1.1.32.11.1.1 | ColumnlldpPortConfigPortNum | not-accessible | current | The index value used to identify the port component (contained in the local chassis with the LLDP agent) associated with this entry. The value of this object i… |
| 1.3.6.1.4.1.171.10.134.1.1.32.11.1.2 | ColumnlldpPortConfigAdminStatus | read-write | current | The administratively desired status of the local LLDP agent. If the associated lldpPortConfigAdminStatus object has a value of 'txOnly(1)', then LLDP agent wil… |
| 1.3.6.1.4.1.171.10.134.1.1.32.11.1.3 | ColumnlldpPortConfigNotificationEnable | read-write | current | The lldpPortConfigNotificationEnable controls, on a per port basis, whether or not notifications from the agent are enabled. The value true(1) means that notif… |
| 1.3.6.1.4.1.171.10.134.1.1.32.11.1.4 | ColumnlldpPortConfigTLVsTxEnable | read-write | current | The lldpPortConfigTLVsTxEnable, defined as a bitmap, includes the basic set of LLDP TLVs whose transmission is allowed on the local LLDP agent by the network m… |
| 1.3.6.1.4.1.171.10.134.1.1.32.12 | NodelldpXdot3Objects | |||
| 1.3.6.1.4.1.171.10.134.1.1.32.12.1 | NodelldpXdot3Config | |||
| 1.3.6.1.4.1.171.10.134.1.1.32.12.1.1 | TablelldpXdot3PortConfigTable | not-accessible | current | A table that controls selection of LLDP TLVs to be transmitted on individual ports. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.1.1.1 | RowlldpXdot3PortConfigEntry | not-accessible | current | LLDP configuration information that controls the transmission of IEEE 802.3 organizationally defined TLVs on LLDP transmission capable ports. This configuratio… |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.1.1.1.1 | ColumnlldpXdot3PortConfigTLVsTxEnable | read-write | current | The lldpXdot3PortConfigTLVsTxEnable, defined as a bitmap, includes the IEEE 802.3 organizationally defined set of LLDP TLVs whose transmission is allowed on th… |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2 | NodelldpXdot3LocalData | |||
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.1 | TablelldpXdot3LocPortTable | not-accessible | current | This table contains one row per port of Ethernet port information (as a part of the LLDP 802.3 organizational extension) on the local system known to this agen… |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.1.1 | RowlldpXdot3LocPortEntry | not-accessible | current | Information about a particular port component. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.1.1.1 | ColumnlldpXdot3LocPortAutoNegSupported | read-only | current | The truth value used to indicate whether the given port (associated with the local system) supports Auto-negotiation. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.1.1.2 | ColumnlldpXdot3LocPortAutoNegEnabled | read-only | current | The truth value used to indicate whether port Auto-negotiation is enabled on the given port associated with the local system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.1.1.3 | ColumnlldpXdot3LocPortAutoNegAdvertisedCap | read-only | current | This object contains the value (bitmap) of the ifMauAutoNegCapAdvertisedBits object (defined in IETF RFC 3636) which is associated with the given port on the l… |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.1.1.4 | ColumnlldpXdot3LocPortOperMauType | read-only | current | An integer value that indicates the operational MAU type of the given port on the local system. This object contains the integer value derived from the list po… |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.2 | TablelldpXdot3LocPowerTable | not-accessible | current | This table contains one row per port of power ethernet information (as a part of the LLDP 802.3 organizational extension) on the local system known to this age… |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.2.1 | RowlldpXdot3LocPowerEntry | not-accessible | current | Information about a particular port component. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.2.1.1 | ColumnlldpXdot3LocPowerPortClass | read-only | current | The value that identifies the port Class of the given port associated with the local system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.2.1.2 | ColumnlldpXdot3LocPowerMDISupported | read-only | current | The truth value used to indicate whether the MDI power is supported on the given port associated with the local system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.2.1.3 | ColumnlldpXdot3LocPowerMDIEnabled | read-only | current | The truth value used to identify whether MDI power is enabled on the given port associated with the local system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.2.1.4 | ColumnlldpXdot3LocPowerPairControlable | read-only | current | The truth value is derived from the value of pethPsePortPowerPairsControlAbility object (defined in IETF RFC 3621) and is used to indicate whether the pair sel… |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.2.1.5 | ColumnlldpXdot3LocPowerPairs | read-only | current | This object contains the value of the pethPsePortPowerPairs object (defined in IETF RFC 3621) which is associated with the given port on the local system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.2.1.6 | ColumnlldpXdot3LocPowerClass | read-only | current | This object contains the value of the pethPsePortPowerClassifications object (defined in IETF RFC 3621) which is associated with the given port on the local sy… |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.3 | TablelldpXdot3LocLinkAggTable | not-accessible | current | This table contains one row per port of link aggregation information (as a part of the LLDP 802.3 organizational extension) on the local system known to this a… |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.3.1 | RowlldpXdot3LocLinkAggEntry | not-accessible | current | Link Aggregation information about a particular port component. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.3.1.1 | ColumnlldpXdot3LocLinkAggStatus | read-only | current | The bitmap value contains the link aggregation capabilities and the current aggregation status of the link. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.3.1.2 | ColumnlldpXdot3LocLinkAggPortId | read-only | current | This object contains the IEEE 802.3 aggregated port identifier, aAggPortID (IEEE 802.3-2002, 30.7.2.1.1), derived from the ifNumber of the ifIndex for the port… |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.4 | TablelldpXdot3LocMaxFrameSizeTable | not-accessible | current | This table contains one row per port of maximum frame size information (as a part of the LLDP 802.3 organizational extension) on the local system known to this… |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.4.1 | RowlldpXdot3LocMaxFrameSizeEntry | not-accessible | current | Maximum Frame Size information about a particular port component. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.2.4.1.1 | ColumnlldpXdot3LocMaxFrameSize | read-only | current | An integer value indicating the maximum supported frame size in octets on the given port of the local system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3 | NodelldpXdot3RemoteData | |||
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.1 | TablelldpXdot3RemPortTable | not-accessible | current | This table contains Ethernet port information (as a part of the LLDP 802.3 organizational extension) of the remote system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.1.1 | RowlldpXdot3RemPortEntry | not-accessible | current | Information about a particular physical network connection. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.1.1.1 | ColumnlldpXdot3RemPortAutoNegSupported | read-only | current | The truth value used to indicate whether the given port (associated with remote system) supports Auto-negotiation. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.1.1.2 | ColumnlldpXdot3RemPortAutoNegEnabled | read-only | current | The truth value used to indicate whether port Auto-negotiation is enabled on the given port associated with the remote system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.1.1.3 | ColumnlldpXdot3RemPortAutoNegAdvertisedCap | read-only | current | This object contains the value (bitmap) of the ifMauAutoNegCapAdvertisedBits object (defined in IETF RFC 3636) which is associated with the given port on the r… |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.1.1.4 | ColumnlldpXdot3RemPortOperMauType | read-only | current | An integer value that indicates the operational MAU type of the sending device. This object contains the integer value derived from the list position of the co… |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.2 | TablelldpXdot3RemPowerTable | not-accessible | current | This table contains Ethernet power information (as a part of the LLDP 802.3 organizational extension) of the remote system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.2.1 | RowlldpXdot3RemPowerEntry | not-accessible | current | Information about a particular physical network connection. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.2.1.1 | ColumnlldpXdot3RemPowerPortClass | read-only | current | The value that identifies the port Class of the given port associated with the remote system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.2.1.2 | ColumnlldpXdot3RemPowerMDISupported | read-only | current | The truth value used to indicate whether the MDI power is supported on the given port associated with the remote system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.2.1.3 | ColumnlldpXdot3RemPowerMDIEnabled | read-only | current | The truth value used to identify whether MDI power is enabled on the given port associated with the remote system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.2.1.4 | ColumnlldpXdot3RemPowerPairControlable | read-only | current | The truth value is derived from the value of pethPsePortPowerPairsControlAbility object (defined in IETF RFC 3621) and is used to indicate whether the pair sel… |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.2.1.5 | ColumnlldpXdot3RemPowerPairs | read-only | current | This object contains the value of the pethPsePortPowerPairs object (defined in IETF RFC 3621) which is associated with the given port on the remote system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.2.1.6 | ColumnlldpXdot3RemPowerClass | read-only | current | This object contains the value of the pethPsePortPowerClassifications object (defined in IETF RFC 3621) which is associated with the given port on the remote s… |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.3 | TablelldpXdot3RemLinkAggTable | not-accessible | current | This table contains port link aggregation information (as a part of the LLDP 802.3 organizational extension) of the remote system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.3.1 | RowlldpXdot3RemLinkAggEntry | not-accessible | current | Link Aggregation information about remote system's port component. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.3.1.1 | ColumnlldpXdot3RemLinkAggStatus | read-only | current | The bitmap value contains the link aggregation capabilities and the current aggregation status of the link. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.3.1.2 | ColumnlldpXdot3RemLinkAggPortId | read-only | current | This object contains the IEEE 802.3 aggregated port identifier, aAggPortID (IEEE 802.3-2002, 30.7.2.1.1), derived from the ifNumber of the ifIndex for the port… |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.4 | TablelldpXdot3RemMaxFrameSizeTable | not-accessible | current | This table contains one row per port of maximum frame size information (as a part of the LLDP 802.3 organizational extension) of the remote system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.4.1 | RowlldpXdot3RemMaxFrameSizeEntry | not-accessible | current | Maximum Frame Size information about a particular port component. |
| 1.3.6.1.4.1.171.10.134.1.1.32.12.3.4.1.1 | ColumnlldpXdot3RemMaxFrameSize | read-only | current | An integer value indicating the maximum supported frame size in octets on the port component associated with the remote system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13 | NodelldpXdot1Objects | |||
| 1.3.6.1.4.1.171.10.134.1.1.32.13.1 | NodelldpXdot1Config | |||
| 1.3.6.1.4.1.171.10.134.1.1.32.13.1.1 | TablelldpXdot1ConfigPortVlanTable | not-accessible | current | A table that controls selection of LLDP Port VLAN-ID TLVs to be transmitted on individual ports. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.1.1.1 | RowlldpXdot1ConfigPortVlanEntry | not-accessible | current | LLDP configuration information that controls the transmission of IEEE 802.1 organizationally defined Port VLAN-ID TLV on LLDP transmission capable ports. This … |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.1.1.1.1 | ColumnlldpXdot1ConfigPortVlanTxEnable | read-write | current | The lldpXdot1ConfigPortVlanTxEnable, which is defined as a truth value and configured by the network management, determines whether the IEEE 802.1 organization… |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.1.2 | TablelldpXdot1ConfigVlanNameTable | not-accessible | current | The table that controls selection of LLDP VLAN name TLV instances to be transmitted on individual ports. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.1.2.1 | RowlldpXdot1ConfigVlanNameEntry | not-accessible | current | LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System VLAN name instance will be transmitted. Th… |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.1.2.1.1 | ColumnlldpXdot1ConfigVlanNameTxEnable | read-write | current | The boolean value that indicates whether the corresponding Local System VLAN name instance will be transmitted on the port defined by the given lldpXdot1LocVla… |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.1.3 | TablelldpXdot1ConfigProtoVlanTable | not-accessible | current | The table that controls selection of LLDP Port and Protocol VLAN ID TLV instances to be transmitted on individual ports. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.1.3.1 | RowlldpXdot1ConfigProtoVlanEntry | not-accessible | current | LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System Protocol VLAN instance will be transmitted… |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.1.3.1.1 | ColumnlldpXdot1ConfigProtoVlanTxEnable | read-write | current | The boolean value that indicates whether the corresponding Local System Port and Protocol VLAN instance will be transmitted on the port defined by the given ll… |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.1.4 | TablelldpXdot1ConfigProtocolTable | not-accessible | current | The table that controls selection of LLDP Protocol TLV instances to be transmitted on individual ports. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.1.4.1 | RowlldpXdot1ConfigProtocolEntry | not-accessible | current | LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System Protocol instance will be transmitted. Thi… |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.1.4.1.1 | ColumnlldpXdot1ConfigProtocolTxEnable | read-write | current | The boolean value that indicates whether the corresponding Local System Protocol Identity instance will be transmitted on the port defined by the given lldpXdo… |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.2 | NodelldpXdot1LocalData | |||
| 1.3.6.1.4.1.171.10.134.1.1.32.13.2.1 | TablelldpXdot1LocTable | not-accessible | current | This table contains one row per port for IEEE 802.1 organizationally defined LLDP extension on the local system known to this agent. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.2.1.1 | RowlldpXdot1LocEntry | not-accessible | current | Information about IEEE 802.1 organizationally defined LLDP extension. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.2.1.1.1 | ColumnlldpXdot1LocPortVlanId | read-only | current | The integer value used to identify the port's VLAN identifier associated with the local system. A value of zero shall be used if the system either does not kno… |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.2.2 | TablelldpXdot1LocProtoVlanTable | not-accessible | current | This table contains one or more rows per Port and Protocol VLAN information about the local system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.2.2.1 | RowlldpXdot1LocProtoVlanEntry | not-accessible | current | Port and protocol VLAN ID Information about a particular port component. There may be multiple port and protocol VLANs, identified by a particular lldpXdot1Loc… |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.2.2.1.1 | ColumnlldpXdot1LocProtoVlanId | not-accessible | current | The integer value used to identify the port and protocol VLANs associated with the given port associated with the local system. A value of zero shall be used i… |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.2.2.1.2 | ColumnlldpXdot1LocProtoVlanSupported | read-only | current | The truth value used to indicate whether the given port (associated with the local system) supports port and protocol VLANs. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.2.2.1.3 | ColumnlldpXdot1LocProtoVlanEnabled | read-only | current | The truth value used to indicate whether the port and protocol VLANs are enabled on the given port associated with the local system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.2.3 | TablelldpXdot1LocVlanNameTable | not-accessible | current | This table contains one or more rows per IEEE 802.1Q VLAN name information on the local system known to this agent. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.2.3.1 | RowlldpXdot1LocVlanNameEntry | not-accessible | current | VLAN name Information about a particular port component. There may be multiple VLANs, identified by a particular lldpXdot1LocVlanId, configured on the given po… |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.2.3.1.1 | ColumnlldpXdot1LocVlanId | not-accessible | current | The integer value used to identify the IEEE 802.1Q VLAN IDs with which the given port is compatible. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.2.3.1.2 | ColumnlldpXdot1LocVlanName | read-only | current | The string value used to identify VLAN name identified by the Vlan Id associated with the given port on the local system. This object should contain the value … |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.2.4 | TablelldpXdot1LocProtocolTable | not-accessible | current | This table contains one or more rows per protocol identity information on the local system known to this agent. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.2.4.1 | RowlldpXdot1LocProtocolEntry | not-accessible | current | Information about particular protocols that are accessible through the given port component. There may be multiple protocols, identified by particular lldpXdot… |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.2.4.1.1 | ColumnlldpXdot1LocProtocolIndex | not-accessible | current | This object represents an arbitrary local integer value used by this agent to identify a particular protocol identity. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.2.4.1.2 | ColumnlldpXdot1LocProtocolId | read-only | current | The octet string value used to identify the protocols associated with the given port of the local system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.3 | NodelldpXdot1RemoteData | |||
| 1.3.6.1.4.1.171.10.134.1.1.32.13.3.1 | TablelldpXdot1RemTable | not-accessible | current | This table contains one or more rows per physical network connection known to this agent. The agent may wish to ensure that only one lldpXdot1RemEntry is prese… |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.3.1.1 | RowlldpXdot1RemEntry | not-accessible | current | Information about a particular port component. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.3.1.1.1 | ColumnlldpXdot1RemPortVlanId | read-only | current | The integer value used to identify the port's VLAN identifier associated with the remote system. if the remote system either does not know the PVID or does not… |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.3.2 | TablelldpXdot1RemProtoVlanTable | not-accessible | current | This table contains one or more rows per Port and Protocol VLAN information about the remote system, received on the given port. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.3.2.1 | RowlldpXdot1RemProtoVlanEntry | not-accessible | current | Port and protocol VLAN name Information about a particular port component. There may be multiple protocol VLANs, identified by a particular lldpXdot1RemProtoVl… |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.3.2.1.1 | ColumnlldpXdot1RemProtoVlanId | not-accessible | current | The integer value used to identify the port and protocol VLANs associated with the given port associated with the remote system. If port and protocol VLANs are… |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.3.2.1.2 | ColumnlldpXdot1RemProtoVlanSupported | read-only | current | The truth value used to indicate whether the given port (associated with the remote system) is capable of supporting port and protocol VLANs. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.3.2.1.3 | ColumnlldpXdot1RemProtoVlanEnabled | read-only | current | The truth value used to indicate whether the port and protocol VLANs are enabled on the given port associated with the remote system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.3.3 | TablelldpXdot1RemVlanNameTable | not-accessible | current | This table contains one or more rows per IEEE 802.1Q VLAN name information about the remote system, received on the given port. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.3.3.1 | RowlldpXdot1RemVlanNameEntry | not-accessible | current | VLAN name Information about a particular port component. There may be multiple VLANs, identified by a particular lldpXdot1RemVlanId, received on the given port. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.3.3.1.1 | ColumnlldpXdot1RemVlanId | not-accessible | current | The integer value used to identify the IEEE 802.1Q VLAN IDs with which the given port of the remote system is compatible. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.3.3.1.2 | ColumnlldpXdot1RemVlanName | read-only | current | The string value used to identify VLAN name identified by the VLAN Id associated with the remote system. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.3.4 | TablelldpXdot1RemProtocolTable | not-accessible | current | This table contains one or more rows per protocol information about the remote system, received on the given port. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.3.4.1 | RowlldpXdot1RemProtocolEntry | not-accessible | current | Protocol information about a particular port component. There may be multiple protocols, identified by a particular lldpXdot1ProtocolIndex, received on the giv… |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.3.4.1.1 | ColumnlldpXdot1RemProtocolIndex | not-accessible | current | This object represents an arbitrary local integer value used by this agent to identify a particular protocol identity. |
| 1.3.6.1.4.1.171.10.134.1.1.32.13.3.4.1.2 | ColumnlldpXdot1RemProtocolId | read-only | current | The octet string value used to identify the protocols associated with the given port of remote system. |
| 1.3.6.1.4.1.171.10.134.1.1.33 | NodecompanyCPUInterfaceFilterGroup | |||
| 1.3.6.1.4.1.171.10.134.1.1.33.1 | NodecpuFilterProfile | |||
| 1.3.6.1.4.1.171.10.134.1.1.33.1.1 | Tableipv4cpuFilterProfileTable | not-accessible | current | A table to CPUInterfaceFilter profile . |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.1.1 | Rowipv4cpuFilterProfileEntry | not-accessible | current | Each entry in this table is a CPUInterfaceFilter profile. Index to the table is CPUInterfaceFilter profile ID. |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.1.1.1 | Columnipv4cpuFilterProfileNo | read-only | current | The CPUInterfaceFilter Profile ID. The ID 1 to 50 is user-defined CPUInterfaceFilter, and the ID more than 50 is reserved for system-defined CPUInterfaceFilter… |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.1.1.2 | Columnipv4cpuFilterProfileType | read-write | current | The CPUInterfaceFilter Profile type, possible value are l2 (1) - for MAC-based rule, l3 (2) - for IPv4-based rule, l3v6 (11) - for IPv6-based rule |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.1.1.3 | Columnipv4cpuFilterProfileRuleCount | read-only | current | The number of rules in this profile. |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.1.1.4 | Columnipv4cpuFilterProfileMask | read-write | current | Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT L2 DST_MAC 0 (LSB) L2 SRC_MAC 1 L2 VID … |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.1.1.5 | Columnipv4cpuFilterProfileDstMacAddrMask | read-write | current | The CPUInterfaceFilter Profile destination MAC address mask. If DST_MAC is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL2… |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.1.1.6 | Columnipv4cpuFilterProfileSrcMacAddrMask | read-write | current | The CPUInterfaceFilter Profile source MAC address mask. If SRC_MAC is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL2RuleS… |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.1.1.7 | Columnipv4cpuFilterProfileIPProtocol | read-write | current | Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none. |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.1.1.8 | Columnipv4cpuFilterProfileIPProtocolMask | read-write | current | The CPUInterfaceFilter Profile IP protocol mask. If cpuFilterProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule fie… |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.1.1.9 | Columnipv4cpuFilterProfileDstIpAddrMask | read-write | current | The CPUInterfaceFilter Profile destination IP address mask. If DST_IP is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3Ru… |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.1.1.10 | Columnipv4cpuFilterProfileSrcIpAddrMask | read-write | current | The CPUInterfaceFilter Profile source IP address mask. If SRC_IP is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleSrc… |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.1.1.11 | Columnipv4cpuFilterProfileDstPortMask | read-write | current | The CPUInterfaceFilter Profile UDP/TCP destination port mask. If DST_PORT is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilter… |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.1.1.12 | Columnipv4cpuFilterProfileSrcPortMask | read-write | current | The CPUInterfaceFilter Profile UDP/TCP source port mask. If SRC_PORT is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3Rul… |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.1.1.15 | Columnipv4cpuFilterProfileStatus | read-create | current | This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait… |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.2 | TablecpuFilterProfileTable | not-accessible | current | A table to CPUInterfaceFilter profile . |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.2.1 | RowcpuFilterProfileEntry | not-accessible | current | Each entry in this table is a CPUInterfaceFilter profile. Index to the table is CPUInterfaceFilter profile ID. |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.2.1.1 | ColumncpuFilterProfileNo | read-only | current | The CPUInterfaceFilter Profile ID. The ID 1 to 50 is user-defined CPUInterfaceFilter, and the ID more than 50 is reserved for system-defined CPUInterfaceFilter… |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.2.1.2 | ColumncpuFilterProfileType | read-write | current | The CPUInterfaceFilter Profile type, possible value are l2 (1) - for MAC-based rule, l3 (2) - for IPv4-based rule, l3v6 (11) - for IPv6-based rule |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.2.1.3 | ColumncpuFilterProfileRuleCount | read-only | current | The number of rules in this profile. |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.2.1.4 | ColumncpuFilterProfileMask | read-write | current | Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT L2 DST_MAC 0 (LSB) L2 SRC_MAC 1 L2 VID … |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.2.1.5 | ColumncpuFilterProfileDstMacAddrMask | read-write | current | The CPUInterfaceFilter Profile destination MAC address mask. If DST_MAC is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL2… |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.2.1.6 | ColumncpuFilterProfileSrcMacAddrMask | read-write | current | The CPUInterfaceFilter Profile source MAC address mask. If SRC_MAC is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL2RuleS… |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.2.1.7 | ColumncpuFilterProfileIPProtocol | read-write | current | Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none. |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.2.1.8 | ColumncpuFilterProfileIPProtocolMask | read-write | current | The CPUInterfaceFilter Profile IP protocol mask. If cpuFilterProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule fie… |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.2.1.9 | ColumncpuFilterProfileDstIpAddrMaskType | read-write | current | IPv6 Address type. |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.2.1.10 | ColumncpuFilterProfileDstIpAddrMask | read-write | current | The CPUInterfaceFilter Profile destination IP address mask. If DST_IP is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3Ru… |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.2.1.11 | ColumncpuFilterProfileSrcIpAddrMaskType | read-write | current | IPv6 Address type. |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.2.1.12 | ColumncpuFilterProfileSrcIpAddrMask | read-write | current | The CPUInterfaceFilter Profile source IP address mask. If SRC_IP is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleSrc… |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.2.1.13 | ColumncpuFilterProfileDstPortMask | read-write | current | The CPUInterfaceFilter Profile UDP/TCP destination port mask. If DST_PORT is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilter… |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.2.1.14 | ColumncpuFilterProfileSrcPortMask | read-write | current | The CPUInterfaceFilter Profile UDP/TCP source port mask. If SRC_PORT is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3Rul… |
| 1.3.6.1.4.1.171.10.134.1.1.33.1.2.1.15 | ColumncpuFilterProfileStatus | read-create | current | This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait… |
| 1.3.6.1.4.1.171.10.134.1.1.33.2 | NodecpuFilterL2Rule | |||
| 1.3.6.1.4.1.171.10.134.1.1.33.2.1 | TablecpuFilterL2RuleTable | not-accessible | current | A table to configure L2 filter rules in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.33.2.1.1 | RowcpuFilterL2RuleEntry | not-accessible | current | Each entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID. |
| 1.3.6.1.4.1.171.10.134.1.1.33.2.1.1.1 | ColumncpuFilterL2ProfileID | read-only | current | L2 Filter rule ID. |
| 1.3.6.1.4.1.171.10.134.1.1.33.2.1.1.2 | ColumncpuFilterL2AccessID | read-only | current | CPUInterfaceFilter Profile ID which this rule join. |
| 1.3.6.1.4.1.171.10.134.1.1.33.2.1.1.3 | ColumncpuFilterL2RuleEtherType | read-write | current | The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '-1', which means the rule don't ca… |
| 1.3.6.1.4.1.171.10.134.1.1.33.2.1.1.4 | ColumncpuFilterL2RuleDstMacAddr | read-write | current | Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero,which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.2.1.1.5 | ColumncpuFilterL2RuleSrcMacAddr | read-write | current | Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero, which means the rule don't care this condition.. address |
| 1.3.6.1.4.1.171.10.134.1.1.33.2.1.1.6 | ColumncpuFilterL2RuleVlanId | read-write | current | Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule… |
| 1.3.6.1.4.1.171.10.134.1.1.33.2.1.1.7 | ColumncpuFilterL2Rule1pPriority | read-write | current | 802.1p priority to be matched with the packet. By Default, the value will be '-1', which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.2.1.1.8 | ColumncpuFilterL2RuleDstMacAddrMask | read-only | current | The MAC address Mask work for Destination MAC address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.33.2.1.1.9 | ColumncpuFilterL2RuleSrcMacAddrMask | read-only | current | The MAC address Mask work for Source MAC address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.33.2.1.1.10 | ColumncpuFilterL2RuleInPortList | read-write | current | Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list. |
| 1.3.6.1.4.1.171.10.134.1.1.33.2.1.1.11 | ColumncpuFilterL2RuleAction | read-write | current | Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding r… |
| 1.3.6.1.4.1.171.10.134.1.1.33.2.1.1.14 | ColumncpuFilterL2RuleStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.134.1.1.33.3 | NodecpuFilterL3Rule | |||
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1 | TablecpuFilterL3RuleTable | not-accessible | current | A table to configure L3 filter rules in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1 | RowcpuFilterL3RuleEntry | not-accessible | current | Each entry in this table is a L3 filter rule. Index to the table is L3 filter number and Profile ID. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.1 | ColumncpuFilterL3RuleProfileNo | read-only | current | L3 Filter rule ID. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.2 | ColumncpuFilterL3RuleAccessID | read-only | current | The Profile ID which this rule join. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.3 | ColumncpuFilterL3RuleProtocol | read-write | current | The type of protocol to be checked against the packet. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.4 | ColumncpuFilterL3RuleProtocolMask | read-only | current | The IP protocol mask. This field is read-only and copy from it's Profile setting. It will work with the other field,cpuFilterL3RuleProtocol, to caculate a rang… |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.5 | ColumncpuFilterL3RuleICMPMessageType | read-write | current | The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action s… |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.6 | ColumncpuFilterL3RuleICMPMessageCode | read-write | current | The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action s… |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.7 | ColumncpuFilterL3RuleDstIpAddr | read-write | current | Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.8 | ColumncpuFilterL3RuleSrcIpAddr | read-write | current | Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.9 | ColumncpuFilterL3RuleDstIpAddrMask | read-only | current | The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.10 | ColumncpuFilterL3RuleSrcIpAddrMask | read-only | current | The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.11 | ColumncpuFilterL3RuleTcpUdpDstPort | read-write | current | The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.12 | ColumncpuFilterL3RuleTcpUdpSrcPort | read-write | current | The TCP / UDP source port. The default value is -1, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.13 | ColumncpuFilterL3RuleTcpUdpDstPortMask | read-only | current | The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.14 | ColumncpuFilterL3RuleTcpUdpSrcPortMask | read-only | current | The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.15 | ColumncpuFilterL3RuleTcpAckBit | read-create | current | The TCP ACK bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.16 | ColumncpuFilterL3RuleTcpRstBit | read-create | current | The TCP RST bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.17 | ColumncpuFilterL3RuleTcpUrgBit | read-create | current | The TCP Urg bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.18 | ColumncpuFilterL3RuleTcpPshBit | read-create | current | The TCP Psh bit to be checked against the packet. The default value is 'dontcare'(-1). which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.19 | ColumncpuFilterL3RuleTcpSynBit | read-create | current | The TCP Syn bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.20 | ColumncpuFilterL3RuleTcpFinBit | read-create | current | The TCP Fin bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.21 | ColumncpuFilterL3RuleDscp | read-create | current | The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.22 | ColumncpuFilterL3RuleIgmpType | read-write | current | The IGMP Type to be checked against the packet.A default value is '-1', which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.23 | ColumncpuFilterL3RulePortList | read-write | current | Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.24 | ColumncpuFilterL3RuleAction | read-write | current | Specifies the action to be taken on the packet if the filter rule matches. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.1.1.27 | ColumncpuFilterL3RuleStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2 | TablecpuFilterv6L3RuleTable | not-accessible | current | A table to configure L3 filter rules in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1 | RowcpuFilterv6L3RuleEntry | not-accessible | current | Each entry in this table is a L3 filter rule. Index to the table is L3 filter number and Profile ID. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.1 | ColumncpuFilterv6L3RuleProfileNo | read-only | current | L3 Filter rule ID. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.2 | ColumncpuFilterv6L3RuleAccessID | read-only | current | The Profile ID which this rule join. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.3 | ColumncpuFilterv6L3RuleProtocol | read-write | current | The type of protocol to be checked against the packet. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.4 | ColumncpuFilterv6L3RuleProtocolMask | read-only | current | The IP protocol mask. This field is read-only and copy from it's Profile setting. It will work with the other field,cpuFilterL3RuleProtocol, to caculate a rang… |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.5 | ColumncpuFilterv6L3RuleICMPMessageType | read-write | current | The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action s… |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.6 | ColumncpuFilterv6L3RuleICMPMessageCode | read-write | current | The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action s… |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.7 | ColumncpuFilterv6L3RuleDstIpAddr | read-write | current | Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.8 | ColumncpuFilterv6L3RuleSrcIpAddr | read-write | current | Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.9 | ColumncpuFilterv6L3RuleDstIpAddrMask | read-only | current | The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.10 | ColumncpuFilterv6L3RuleSrcIpAddrMask | read-only | current | The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.11 | ColumncpuFilterv6L3RuleTcpUdpDstPort | read-write | current | The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.12 | ColumncpuFilterv6L3RuleTcpUdpSrcPort | read-write | current | The TCP / UDP source port. The default value is -1, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.13 | ColumncpuFilterv6L3RuleTcpUdpDstPortMask | read-only | current | The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.14 | ColumncpuFilterv6L3RuleTcpUdpSrcPortMask | read-only | current | The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.15 | ColumncpuFilterv6L3RuleTcpAckBit | read-create | current | The TCP ACK bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.16 | ColumncpuFilterv6L3RuleTcpRstBit | read-create | current | The TCP RST bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.17 | ColumncpuFilterv6L3RuleTcpUrgBit | read-create | current | The TCP Urg bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.18 | ColumncpuFilterv6L3RuleTcpPshBit | read-create | current | The TCP Psh bit to be checked against the packet. The default value is 'dontcare'(-1). which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.19 | ColumncpuFilterv6L3RuleTcpSynBit | read-create | current | The TCP Syn bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.20 | ColumncpuFilterv6L3RuleTcpFinBit | read-create | current | The TCP Fin bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.21 | ColumncpuFilterv6L3RuleTrafficClass | read-create | current | The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.22 | ColumncpuFilterv6L3RulePortList | read-write | current | Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.23 | ColumncpuFilterv6L3RuleAction | read-write | current | Specifies the action to be taken on the packet if the filter rule matches. |
| 1.3.6.1.4.1.171.10.134.1.1.33.3.2.1.24 | ColumncpuFilterv6L3RuleStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.134.1.1.35 | NodecompanyCableDiagnostic | |||
| 1.3.6.1.4.1.171.10.134.1.1.35.1 | ScalarcableDiagTriggerIndex | read-write | current | Trigger an interface index to do cable diagnostic. |
| 1.3.6.1.4.1.171.10.134.1.1.35.2 | ScalarcableDiagPair1TestResult | read-only | current | Cable diagnostics pair 1 test result. |
| 1.3.6.1.4.1.171.10.134.1.1.35.3 | ScalarcableDiagPair1FaultDistance | read-only | current | Cable Diagnostics pair 1 fault distance. |
| 1.3.6.1.4.1.171.10.134.1.1.35.4 | ScalarcableDiagPair2TestResult | read-only | current | Cable diagnostics pair 2 test result. |
| 1.3.6.1.4.1.171.10.134.1.1.35.5 | ScalarcableDiagPair2FaultDistance | read-only | current | Cable diagnostics pair 2 fault distance. |
| 1.3.6.1.4.1.171.10.134.1.1.35.6 | ScalarcableDiagPair3TestResult | read-only | current | Cable diagnostics pair 3 test result. |
| 1.3.6.1.4.1.171.10.134.1.1.35.7 | ScalarcableDiagPair3FaultDistance | read-only | current | Cable diagnostics pair 3 fault distance. |
| 1.3.6.1.4.1.171.10.134.1.1.35.8 | ScalarcableDiagPair4TestResult | read-only | current | Cable diagnostics pair 4 test result. |
| 1.3.6.1.4.1.171.10.134.1.1.35.9 | ScalarcableDiagPair4FaultDistance | read-only | current | Cable diagnostics pair 4 fault distance. |
| 1.3.6.1.4.1.171.10.134.1.1.35.10 | ScalarcableDiagLengthinRange | read-only | current | Cable diagnostics length when link up in speed 1G. (Display in range) |
| 1.3.6.1.4.1.171.10.134.1.1.37 | NodecompanyQinQ | |||
| 1.3.6.1.4.1.171.10.134.1.1.37.1 | NodeqinqSystem | |||
| 1.3.6.1.4.1.171.10.134.1.1.37.1.1 | ScalarqinqGlobalStatus | read-write | current | This object is used to enable/disable the Q-in-Q status. |
| 1.3.6.1.4.1.171.10.134.1.1.37.1.2 | TableqinqTable | not-accessible | current | A table that contains Q-in-Q VLAN mode information about each port. |
| 1.3.6.1.4.1.171.10.134.1.1.37.1.2.1 | RowqinqEntry | not-accessible | current | A list of Q-in-Q VLAN mode information for each port. |
| 1.3.6.1.4.1.171.10.134.1.1.37.1.2.1.1 | ColumnqinqIfIndex | read-only | current | The index of the port. |
| 1.3.6.1.4.1.171.10.134.1.1.37.1.2.1.2 | ColumnqinqRoleState | read-write | current | Sets the QinQ Role as NNI or UNI. |
| 1.3.6.1.4.1.171.10.134.1.1.37.1.2.1.3 | ColumnqinqOuterTPID | read-write | current | Sets the QinQ Outer TPID value. |
| 1.3.6.1.4.1.171.10.134.1.1.38 | NodecompanyTimeRangeMgmt | |||
| 1.3.6.1.4.1.171.10.134.1.1.38.1 | TableswTimeRangeSettingTable | not-accessible | current | A table to configure time Range in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1 | RowswTimeRangeSettingEntry | not-accessible | current | A schedule entry to configure time Range in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.1 | ColumnswTimeRangeIndex | read-only | current | The Time Range identifier. The maximum number of Schedule entry is the number of ports supported PoE function. The value must be between 1 and 52. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.2 | ColumnswTimeRangeName | read-write | current | The Schedule name associated with the Schedule entry (e.g., `abc, bbb'). |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.3 | ColumnswTimeRangeDate | read-write | current | Enable/Disable date range checking while executing time base PoE. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.4 | ColumnswTimeRangeStartYear | read-write | current | Start year of the Schedule entry. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.5 | ColumnswTimeRangeStartMonth | read-write | current | Start month of the Schedule entry. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.6 | ColumnswTimeRangeStartDay | read-write | current | Start day of the Schedule entry. The value must be from 1 to 31. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.7 | ColumnswTimeRangeStartHour | read-write | current | Start hour of the Schedule entry. The value must be from 0 to 23. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.8 | ColumnswTimeRangeStartMinute | read-write | current | Start minute of the Schedule entry. The value must be from 0 to 59. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.9 | ColumnswTimeRangeEndYear | read-write | current | End year of the Schedule entry. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.10 | ColumnswTimeRangeEndMonth | read-write | current | End month of the Schedule entry. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.11 | ColumnswTimeRangeEndDay | read-write | current | End day of the Schedule entry. The value must be from 1 to 31. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.12 | ColumnswTimeRangeEndHour | read-write | current | End hour of the Schedule entry. The value must be from 0 to 23. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.13 | ColumnswTimeRangeEndMinute | read-write | current | End minute of the Schedule entry. The value must be from 0 to 59. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.14 | ColumnswTimeRangeMonday | read-write | current | Enable/Disble scheduling Monday. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.15 | ColumnswTimeRangeTuesday | read-write | current | Enable/Disble scheduling Tuesday. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.16 | ColumnswTimeRangeWednesday | read-write | current | Enable/Disble scheduling Wednesday. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.17 | ColumnswTimeRangeThursday | read-write | current | Enable/Disble scheduling Thursday. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.18 | ColumnswTimeRangeFriday | read-write | current | Enable/Disble scheduling Friday. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.19 | ColumnswTimeRangeSaturday | read-write | current | Enable/Disble scheduling Saturday. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.20 | ColumnswTimeRangeSunday | read-write | current | Enable/Disble scheduling Sunday. |
| 1.3.6.1.4.1.171.10.134.1.1.38.1.1.21 | ColumnswTimeRangeRowStatus | read-create | current | The status of an entry in the Time Range Information Table. Only a subset of the rowstatus variables (active, notinservice, createAndWait, destroy) are availab… |
| 1.3.6.1.4.1.171.10.134.1.1.45 | NodecompanyLimitIp | |||
| 1.3.6.1.4.1.171.10.134.1.1.45.1 | TablelimitIpMulticastProfileTable | not-accessible | current | A list of the limit ip multicast Profile Table. |
| 1.3.6.1.4.1.171.10.134.1.1.45.1.1 | RowlimitIpMulticastProfileEntry | not-accessible | current | A limit ip multicast entry maintain by the start IP Address, end ip address, profile id. |
| 1.3.6.1.4.1.171.10.134.1.1.45.1.1.1 | ColumnlimitIpMulticastIPType | read-only | current | Indicate the IP type of profile. |
| 1.3.6.1.4.1.171.10.134.1.1.45.1.1.2 | ColumnlimitIpMulticastProfileID | read-only | current | The ProfileID of the limit ip multicast profile entry. |
| 1.3.6.1.4.1.171.10.134.1.1.45.1.1.3 | ColumnlimitIpMulticastProfileName | read-write | current | The ProfileName of the limit ip multicast profile entry. |
| 1.3.6.1.4.1.171.10.134.1.1.45.1.1.4 | ColumnlimitIpMulticastProfileStatus | read-write | current | The status of an entry in the limit ip multicast profile Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
| 1.3.6.1.4.1.171.10.134.1.1.45.2 | TablelimitIpMulticastEntryTable | not-accessible | current | A list of the limit ip multicast entry Table. |
| 1.3.6.1.4.1.171.10.134.1.1.45.2.1 | RowlimitIpMulticastEntry | not-accessible | current | A limit ip multicast entry maintain by the start IP Address, end ip address, profile id. |
| 1.3.6.1.4.1.171.10.134.1.1.45.2.1.1 | ColumnlimitIpMulticastEntryIPType | read-only | current | Indicate the IP type of entry. |
| 1.3.6.1.4.1.171.10.134.1.1.45.2.1.2 | ColumnlimitIpMulticastEntryProfileID | read-only | current | The ProfileID of the limit ip multicast entry. |
| 1.3.6.1.4.1.171.10.134.1.1.45.2.1.3 | ColumnlimitIpMulticaststartIpAddr | read-only | current | The limit ip multicast IP address is used to set start ip |
| 1.3.6.1.4.1.171.10.134.1.1.45.2.1.4 | ColumnlimitIpMulticastendIpAddr | read-only | current | The limit ip multicast IP address is used to set end ip |
| 1.3.6.1.4.1.171.10.134.1.1.45.2.1.5 | ColumnlimitIpMulticastStatus | read-write | current | The status of an entry in the limit ip multicast entry Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
| 1.3.6.1.4.1.171.10.134.1.1.45.3 | TablelimitIpMulticastPortTable | not-accessible | current | A list of the limit ip multicast Port entry Table. |
| 1.3.6.1.4.1.171.10.134.1.1.45.3.1 | RowlimitIpMulticastPortEntry | not-accessible | current | A limit ip multicast entry maintain by the Port Index. |
| 1.3.6.1.4.1.171.10.134.1.1.45.3.1.1 | ColumnlimitIpMulticastPortIPType | read-only | current | Indicate the IP type of entry. |
| 1.3.6.1.4.1.171.10.134.1.1.45.3.1.2 | ColumnlimitIpMulticastPortID | read-only | current | The Port Index of the limit ip multicast port entry. For all machines give maximum port number. |
| 1.3.6.1.4.1.171.10.134.1.1.45.3.1.3 | ColumnlimitIpMulticastPortState | read-write | current | The limit ip multicast port state |
| 1.3.6.1.4.1.171.10.134.1.1.45.3.1.4 | ColumnlimitIpMulticastPortProfileID | read-write | current | The limit ip multicast port mapping profileID list. |
| 1.3.6.1.4.1.171.10.134.1.1.45.3.1.5 | ColumnlimitIpMulticastPortMaxGrp | read-write | current | The limit ip multicast per-port max group. |
| 1.3.6.1.4.1.171.10.134.1.1.49 | NodecompanyMulticastFilter | |||
| 1.3.6.1.4.1.171.10.134.1.1.49.1 | TablemcastFilterPortTable | not-accessible | current | A table to control multicast filtering modes. |
| 1.3.6.1.4.1.171.10.134.1.1.49.1.1 | RowmcastFilterPortEntry | not-accessible | current | An entry appears in this table for each interface in the mcastFiltertem. Index to the table is the interface index of the port. |
| 1.3.6.1.4.1.171.10.134.1.1.49.1.1.1 | ColumnmcastFilterPortIndex | not-accessible | current | Interface index of the port for which the configuration in this entry applies. For all machines give maximum port number. |
| 1.3.6.1.4.1.171.10.134.1.1.49.1.1.2 | ColumnmcastFilterPortType | read-write | current | Configures the multicast filtering modes as below : forward -Forwards all unregistered groups. filter -Filters all unregistered groups. |
| 1.3.6.1.4.1.171.10.134.1.1.50 | NodecompanyNeighbor | |||
| 1.3.6.1.4.1.171.10.134.1.1.50.1 | TableneighborTable | not-accessible | current | A list of the Neighbor Cache Table. |
| 1.3.6.1.4.1.171.10.134.1.1.50.1.1 | RowneighborEntry | not-accessible | current | A Neighbor cache entry containing the ifindex and ipv6 addr. |
| 1.3.6.1.4.1.171.10.134.1.1.50.1.1.1 | ColumnneighborIfindex | read-only | current | The interface index of the Neighbor entry. Must be conform to the existing interface name. |
| 1.3.6.1.4.1.171.10.134.1.1.50.1.1.2 | ColumnneighborIPv6Addr | read-only | current | Allows the entry of an IP address that will be a Neighbor entry into the Neighbor Cache Table. |
| 1.3.6.1.4.1.171.10.134.1.1.50.1.1.3 | ColumnneighborMACAddr | read-only | current | The MAC address associated of the Neighbor entry. |
| 1.3.6.1.4.1.171.10.134.1.1.50.1.1.4 | ColumnneighborType | read-only | current | The type associated of the Neighbor entry. |
| 1.3.6.1.4.1.171.10.134.1.1.50.1.1.5 | ColumnneighborCacheState | read-only | current | The type associated of the Neighbor entry. |
| 1.3.6.1.4.1.171.10.134.1.1.50.1.1.6 | ColumnneighborActiveStatus | read-only | current | The active status of the Neighbor entry. |
| 1.3.6.1.4.1.171.10.134.1.1.50.1.1.7 | ColumnneighborRowStatus | read-write | current | The status of an entry in the Neighbor Cache Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
| 1.3.6.1.4.1.171.10.134.1.1.51 | NodecompanyEoam | |||
| 1.3.6.1.4.1.171.10.134.1.1.51.1 | NodeeoamSystem | |||
| 1.3.6.1.4.1.171.10.134.1.1.51.1.2 | TableeoamTable | not-accessible | current | A table that contains EOAM mode information about each port. |
| 1.3.6.1.4.1.171.10.134.1.1.51.1.2.1 | RoweoamEntry | not-accessible | current | A list of EOAM mode information for each port. |
| 1.3.6.1.4.1.171.10.134.1.1.51.1.2.1.1 | ColumneoamIfIndex | read-only | current | The index of the port. |
| 1.3.6.1.4.1.171.10.134.1.1.51.1.2.1.2 | ColumneoamState | read-write | current | Sets the EOAM state enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.51.1.2.1.3 | ColumneoamMode | read-write | current | Sets the EOAM mode as active or passive. |
| 1.3.6.1.4.1.171.10.134.1.1.51.1.2.1.4 | ColumneoamReceivedRemoteLoopback | read-write | current | Sets the EOAM received or ignore remote loopback packets. |
| 1.3.6.1.4.1.171.10.134.1.1.51.1.2.1.5 | ColumneoamRemoteLoopback | read-write | current | Sets the EOAM remote loopback start or stop. |
| 1.3.6.1.4.1.171.10.134.1.1.51.1.2.1.6 | ColumneoamDyingGaspEnable | read-write | current | Sets the EOAM dying gasp state enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.51.1.2.1.7 | ColumneoamCriticalEventEnable | read-write | current | Sets the EOAM critical event state enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.51.2 | NodeeoamLinkMonitor | |||
| 1.3.6.1.4.1.171.10.134.1.1.51.2.1 | TableeoamLinkMonitorTable | not-accessible | current | A table that contains EOAM link monitor information about each port. |
| 1.3.6.1.4.1.171.10.134.1.1.51.2.1.1 | RoweoamLinkMonitorEntry | not-accessible | current | A list of EOAM link monitor information for each port. |
| 1.3.6.1.4.1.171.10.134.1.1.51.2.1.1.1 | ColumneoamLinkMonitorIfIndex | read-only | current | The index of the port. |
| 1.3.6.1.4.1.171.10.134.1.1.51.2.1.1.2 | ColumnerrorSymbolNotifyState | read-write | current | Sets the EOAM error symbol notify state enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.51.2.1.1.3 | ColumnerrorSymbolThreshold | read-write | current | Sets the EOAM error symbol threshold. |
| 1.3.6.1.4.1.171.10.134.1.1.51.2.1.1.4 | ColumnerrorSymbolWindow | read-write | current | Sets the EOAM error symbol window. |
| 1.3.6.1.4.1.171.10.134.1.1.51.2.1.1.5 | ColumnerrorFrameNotifyState | read-write | current | Sets the EOAM error frame notify state enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.51.2.1.1.6 | ColumnerrorFrameThreshold | read-write | current | Sets the EOAM error frame threshold. |
| 1.3.6.1.4.1.171.10.134.1.1.51.2.1.1.7 | ColumnerrorFrameWindow | read-write | current | Sets the EOAM error symbol window. |
| 1.3.6.1.4.1.171.10.134.1.1.51.2.1.1.8 | ColumnerrorFrameSecondsNotifyState | read-write | current | Sets the EOAM error symbol notify state enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.51.2.1.1.9 | ColumnerrorFrameSecondsThreshold | read-write | current | Sets the EOAM error symbol threshold. |
| 1.3.6.1.4.1.171.10.134.1.1.51.2.1.1.10 | ColumnerrorFrameSecondsWindow | read-write | current | Sets the EOAM error symbol window. |
| 1.3.6.1.4.1.171.10.134.1.1.51.2.1.1.11 | ColumnerrorFramePeriodNotifyState | read-write | current | Sets the EOAM error symbol notify state enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.51.2.1.1.12 | ColumnerrorFramePeriodThreshold | read-write | current | Sets the EOAM error symbol threshold. |
| 1.3.6.1.4.1.171.10.134.1.1.51.2.1.1.13 | ColumnerrorFramePeriodWindow | read-write | current | Sets the EOAM error symbol window. |
| 1.3.6.1.4.1.171.10.134.1.1.52 | NodecompanyDuld | |||
| 1.3.6.1.4.1.171.10.134.1.1.52.1 | NodeduldSystem | |||
| 1.3.6.1.4.1.171.10.134.1.1.52.1.1 | TableduldTable | not-accessible | current | A table that contains DULD mode information about each port. |
| 1.3.6.1.4.1.171.10.134.1.1.52.1.1.1 | RowduldEntry | not-accessible | current | A list of DULD mode information for each port. |
| 1.3.6.1.4.1.171.10.134.1.1.52.1.1.1.1 | ColumnduldIfIndex | read-only | current | The index of the port. |
| 1.3.6.1.4.1.171.10.134.1.1.52.1.1.1.2 | ColumnduldState | read-write | current | Sets the DULD admin state enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.52.1.1.1.3 | ColumnduldOperState | read-only | current | Gets the DULD Oper state enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.52.1.1.1.4 | ColumnduldMode | read-write | current | Sets the DULD mode as shutdown or normal. |
| 1.3.6.1.4.1.171.10.134.1.1.52.1.1.1.5 | ColumnduldLinkStatus | read-only | current | Gets the DULD link status. |
| 1.3.6.1.4.1.171.10.134.1.1.52.1.1.1.6 | ColumnduldDiscoveryTime | read-write | current | Sets the DULD discovery time. |
| 1.3.6.1.4.1.171.10.134.1.1.86 | NodecompanyDHCPv6Relay | |||
| 1.3.6.1.4.1.171.10.134.1.1.86.1 | Nodedhcpv6RelayControl | |||
| 1.3.6.1.4.1.171.10.134.1.1.86.1.1 | Scalardhcpv6RelayState | read-write | current | This object indicates DHCPv6 relay function is enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.86.1.2 | Scalardhcpv6RelayHopCount | read-write | current | This object indicates the maximum number of router hops that the DHCPv6 packets can cross. |
| 1.3.6.1.4.1.171.10.134.1.1.86.2 | Nodedhcpv6RelayManagement | |||
| 1.3.6.1.4.1.171.10.134.1.1.86.2.1 | Tabledhcpv6RelayInterfaceSettingsTable | not-accessible | current | This table indicates the IP address as a destination to forward (relay) DHCP packets to. |
| 1.3.6.1.4.1.171.10.134.1.1.86.2.1.1 | Rowdhcpv6RelayInterfaceSettingsEntry | not-accessible | current | A list of information indicates the IP address as a destination to forward (relay) DHCP packets to. |
| 1.3.6.1.4.1.171.10.134.1.1.86.2.1.1.1 | Columndhcpv6RelayInterface | read-only | current | This object indicates the maximum number of router hops that the DHCPv6 packets can cross. |
| 1.3.6.1.4.1.171.10.134.1.1.86.2.1.1.2 | Columndhcpv6RelayServerIP | read-only | current | This object indicates the DHCP server IP address. |
| 1.3.6.1.4.1.171.10.134.1.1.86.2.1.1.99 | Columndhcpv6RelayInterfaceSettingsRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.10.134.1.1.86.3 | Nodedhcpv6RelayOption37 | |||
| 1.3.6.1.4.1.171.10.134.1.1.86.3.1 | Scalardhcpv6RelayOption37State | read-write | current | This object indicates DHCPv6 relay option 37 function is enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.86.3.2 | Scalardhcpv6RelayOption37CheckState | read-write | current | This object indicates DHCPv6 relay option 37 Check function is enabled or disabled. |
| 1.3.6.1.4.1.171.10.134.1.1.86.3.3 | Scalardhcpv6RelayOption37RemoteIDType | read-write | current | This object indicates the type of remote ID. |
| 1.3.6.1.4.1.171.10.134.1.1.86.3.4 | Scalardhcpv6RelayOption37RemoteID | read-write | current | This object displays the current remote ID of the device. If RemoteIDType is set to default, the value will be the MAC address of the device, and this object c… |
| 1.3.6.1.4.1.171.10.134.1.1.88 | NodecompanyMldsGroup | |||
| 1.3.6.1.4.1.171.10.134.1.1.88.1 | NodemldsSystem | |||
| 1.3.6.1.4.1.171.10.134.1.1.88.1.1 | ScalarmldsStatus | read-write | current | Enables or disables MLD snooping in the system. When set to 'enabled', the MLDS module starts protocol operations. When set to 'disabled', the MLDS module stop… |
| 1.3.6.1.4.1.171.10.134.1.1.88.1.2 | ScalarmldsRouterPortPurgeInterval | read-write | current | This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInter… |
| 1.3.6.1.4.1.171.10.134.1.1.88.1.3 | ScalarmldsHostPortPurgeInterval | read-write | current | This is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received this timer runs for 'PortPurg… |
| 1.3.6.1.4.1.171.10.134.1.1.88.1.4 | ScalarmldsRobustnessValue | read-write | current | When the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attrib… |
| 1.3.6.1.4.1.171.10.134.1.1.88.1.5 | ScalarmldsGrpQueryInterval | read-write | current | The value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there is any intersted receive… |
| 1.3.6.1.4.1.171.10.134.1.1.88.1.6 | ScalarmldsQueryInterval | read-write | current | This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for VLANs. |
| 1.3.6.1.4.1.171.10.134.1.1.88.1.7 | ScalarmldsQueryMaxResponseTime | read-write | current | The maximum query response time advertised in MLDv1 general queries on this interface. |
| 1.3.6.1.4.1.171.10.134.1.1.88.3 | NodemldsVlan | |||
| 1.3.6.1.4.1.171.10.134.1.1.88.3.3 | TablemldsVlanRouterTable | not-accessible | current | This table contains the list of ports through which a router, in a particular VLAN is reachable. |
| 1.3.6.1.4.1.171.10.134.1.1.88.3.3.1 | RowmldsVlanRouterEntry | not-accessible | current | Contains the VLAN ID and list of ports on which routers are present in the VLAN. |
| 1.3.6.1.4.1.171.10.134.1.1.88.3.3.1.1 | ColumnmldsVlanRouterVlanId | read-only | current | VLAN ID of the ports through which router is reachable. |
| 1.3.6.1.4.1.171.10.134.1.1.88.3.3.1.2 | ColumnmldsVlanRouterPortList | read-only | current | List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically. |
| 1.3.6.1.4.1.171.10.134.1.1.88.3.4 | TablemldsVlanFilterTable | not-accessible | current | This table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.88.3.4.1 | RowmldsVlanFilterEntry | not-accessible | current | Contains snooping status , version and fast leave configuration for a specific VLAN. |
| 1.3.6.1.4.1.171.10.134.1.1.88.3.4.1.1 | ColumnmldsVlanFilterVlanId | read-only | current | Index of MldsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in MldsVlanFilterEntry is to be done. |
| 1.3.6.1.4.1.171.10.134.1.1.88.3.4.1.2 | ColumnmldsVlanSnoopStatus | read-write | current | This object allows you to enable/disable MLDS function on a specific VLAN. |
| 1.3.6.1.4.1.171.10.134.1.1.88.3.4.1.3 | ColumnmldsVlanQuerier | read-only | current | Indicates whether the switch is configured as a querier in the VLAN |
| 1.3.6.1.4.1.171.10.134.1.1.88.3.4.1.4 | ColumnmldsVlanCfgQuerier | read-write | current | The snooping switch can be configured as a querier via this object to send out MLD general queries when IGMP routers are not present in the VLAN. When set to '… |
| 1.3.6.1.4.1.171.10.134.1.1.88.3.4.1.5 | ColumnmldsVlanQueryInterval | read-only | current | This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as … |
| 1.3.6.1.4.1.171.10.134.1.1.88.3.4.1.6 | ColumnmldsVlanRtrPortList | read-write | current | List of ports which are configured statically as router ports |
| 1.3.6.1.4.1.171.10.134.1.1.88.3.4.1.8 | ColumnmldsVlanFastLeave | read-write | current | Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for … |
| 1.3.6.1.4.1.171.10.134.1.1.88.3.5 | TablemldsVlanMulticastGroupTable | not-accessible | current | This table contains MAC based multicast forwarding information. |
| 1.3.6.1.4.1.171.10.134.1.1.88.3.5.1 | RowmldsVlanMulticastGroupEntry | not-accessible | current | This table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded. |
| 1.3.6.1.4.1.171.10.134.1.1.88.3.5.1.1 | ColumnmldsVlanMulticastGroupVlanId | read-only | current | VLAN ID pertaining to the Multicast forwarding entry |
| 1.3.6.1.4.1.171.10.134.1.1.88.3.5.1.2 | ColumnmldsVlanMulticastGroupIpAddress | read-only | current | Multicast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format. |
| 1.3.6.1.4.1.171.10.134.1.1.88.3.5.1.3 | ColumnmldsVlanMulticastGroupMacAddress | read-only | current | Multicast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format. |
| 1.3.6.1.4.1.171.10.134.1.1.88.3.5.1.4 | ColumnmldsVlanMulticastGroupPortList | read-only | current | List of ports onto which the multicast data packets destined for this group will be forwarded. |
| 1.3.6.1.4.1.171.10.134.1.1.88.4 | NodemldsHost | |||
| 1.3.6.1.4.1.171.10.134.1.1.88.4.1 | TablemldsHostTable | not-accessible | current | This table is used to manage the IGMP Host based Fast Leave function of the switch. |
| 1.3.6.1.4.1.171.10.134.1.1.88.4.1.1 | RowmldsHostEntry | not-accessible | current | Contains management entities for IGMP Host based fast leave function. |
| 1.3.6.1.4.1.171.10.134.1.1.88.4.1.1.1 | ColumnmldsHostTableVLANID | read-only | current | VLAN ID of IPv6 Host table entry. |
| 1.3.6.1.4.1.171.10.134.1.1.88.4.1.1.2 | ColumnmldsHostTableGroupAddress | read-only | current | Group address of IPv6 Host table entry. |
| 1.3.6.1.4.1.171.10.134.1.1.88.4.1.1.3 | ColumnmldsHostTablePort | read-only | current | Port number of IPv6 Host table entry. For all machines give maximum port number. |
| 1.3.6.1.4.1.171.10.134.1.1.88.4.1.1.4 | ColumnmldsHostTableHostIPAddress | read-only | current | Host IP address of Group in IPv6 Host table entry. |
| 1.3.6.1.4.1.171.10.134.1.1.98 | NodecompanyPPPoE | |||
| 1.3.6.1.4.1.171.10.134.1.1.98.1 | ScalarpppoeGlobalState | read-write | current | PPPoE global state |
| 1.3.6.1.4.1.171.10.134.1.1.98.2 | TablepppoePortTable | not-accessible | current | A table to control PPPoE features of the device. |
| 1.3.6.1.4.1.171.10.134.1.1.98.2.1 | RowpppoePortEntry | not-accessible | current | An entry appears in PPPoE table for each interface in the system. |
| 1.3.6.1.4.1.171.10.134.1.1.98.2.1.1 | ColumnpppoePortIndex | read-only | current | Interface index of the port for the configuration in this entry applies. |
| 1.3.6.1.4.1.171.10.134.1.1.98.2.1.2 | ColumnpppoePortState | read-write | current | PPPoE per port state |
| 1.3.6.1.4.1.171.10.134.1.1.98.2.1.3 | ColumnpppoePortCircuitIDType | read-write | current | PPPoE per port circuit ID type |
| 1.3.6.1.4.1.171.10.134.1.1.98.2.1.4 | ColumnpppoePortUDFString | read-write | current | PPPoE per port UDF string |
| 1.3.6.1.4.1.171.10.134.1.1.98.2.1.5 | ColumnpppoePortCircuitIDVendor3String | read-write | current | PPPoE per port circuit ID vendor3 string |
| 1.3.6.1.4.1.171.10.134.1.1.98.2.1.6 | ColumnpppoePortRemoteIDType | read-write | current | PPPoE per port remote ID type |
| 1.3.6.1.4.1.171.10.134.1.1.98.2.1.7 | ColumnpppoePortRemoteIDVendor3String | read-write | current | PPPoE per port remote ID vendor3 string |
| 1.3.6.1.4.1.171.10.134.1.1.100 | NodecompanyAgentBasicInfo | |||
| 1.3.6.1.4.1.171.10.134.1.1.100.1 | NodeagentCPUutilization | |||
| 1.3.6.1.4.1.171.10.134.1.1.100.1.1 | ScalaragentCPUutilizationIn5sec | read-only | current | The time scale is set at 5 second intervals. The value will be between 0% (idle) and 100% (very busy). |
| 1.3.6.1.4.1.171.10.134.1.1.100.1.2 | ScalaragentCPUutilizationIn1min | read-only | current | The time scale is set at 1 minute intervals. The value will be between 0% (idle) and 100% (very busy). |
| 1.3.6.1.4.1.171.10.134.1.1.100.1.3 | ScalaragentCPUutilizationIn5min | read-only | current | The time scale is set at 5 minute intervals. The value will be between 0% (idle) and 100% (very busy). |
| 1.3.6.1.4.1.171.10.134.1.1.100.2 | NodeagentMEMutilization | |||
| 1.3.6.1.4.1.171.10.134.1.1.100.2.1 | ScalaragentMEMutilizationIn5sec | read-only | current | The time scale is set at 5 second intervals. The value will be between 0% (idle) and 100% (very busy). |
| 1.3.6.1.4.1.171.10.134.1.1.100.2.2 | ScalaragentMEMutilizationIn1min | read-only | current | The time scale is set at 1 minute intervals. The value will be between 0% (idle) and 100% (very busy). |
| 1.3.6.1.4.1.171.10.134.1.1.100.2.3 | ScalaragentMEMutilizationIn5min | read-only | current | The time scale is set at 5 minute intervals. The value will be between 0% (idle) and 100% (very busy). |
| 1.3.6.1.4.1.171.10.134.1.1.120 | NodecompanyTraps | |||
| 1.3.6.1.4.1.171.10.134.1.1.120.0 | Nodetraps | |||
| 1.3.6.1.4.1.171.10.134.1.1.120.0.1 | NotificationsnmpTrapSNMPAuthentication | current | SnmpV3TrapSNMPAuthentication. | |
| 1.3.6.1.4.1.171.10.134.1.1.120.0.2 | NotificationsnmpTrapColdStart | current | SnmpV3TrapColdStart. | |
| 1.3.6.1.4.1.171.10.134.1.1.120.0.3 | NotificationsnmpTrapWarmStart | current | SnmpV3TrapWarmStart. | |
| 1.3.6.1.4.1.171.10.134.1.1.120.0.4 | NotificationsnmpTrapCopperLinkUpDown | current | SnmpV3TrapCopperLinkUpDown. | |
| 1.3.6.1.4.1.171.10.134.1.1.120.0.5 | NotificationsnmpTrapRSTPStateChange | current | SnmpV3TrapRSTPStateChange. | |
| 1.3.6.1.4.1.171.10.134.1.1.120.0.6 | NotificationsnmpTrapFirmUpgrade | current | SnmpV3TrapFirmUpgrade. | |
| 1.3.6.1.4.1.171.10.134.1.1.120.0.12 | NotificationsnmpTrapPortSecurity | current | SnmpV3TrapPortSecurity. | |
| 1.3.6.1.4.1.171.10.134.1.1.120.0.14 | NotificationsnmpTrapLBD | current | SnmpV3TrapLBD. | |
| 1.3.6.1.4.1.171.10.134.1.1.120.0.17 | NotificationmacNotificatiotn | current | This trap indicates the MAC address variations in the address table . | |
| 1.3.6.1.4.1.171.10.134.1.1.120.0.21 | NotificationduplicateIP | current | duplicateIP . | |
| 1.3.6.1.4.1.171.10.134.1.1.120.0.22 | NotificationtrafficControl | current | trafficControl. | |
| 1.3.6.1.4.1.171.10.134.1.1.120.0.23 | NotificationtopologyChange | current | topologyChange. | |
| 1.3.6.1.4.1.171.10.134.1.1.120.0.24 | NotificationnewRootBrgaddress | current | newRootBrgaddress. | |
| 1.3.6.1.4.1.171.10.134.1.1.120.0.25 | NotificationnewRootOlddesignatedroot | current | newRootOlddesignatedroot. | |
| 1.3.6.1.4.1.171.10.134.1.1.120.0.26 | NotificationnewRootMSTibridgeregionalroot | current | topologyChange. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| BridgeId | OCTET STRING (SIZE (8)) | current | The Bridge-Identifier as used in the Spanning Tree Protocol to uniquely identify a bridge. Its first two octets (in network byte order) contain a priority value and its last 6 octets contain the MAC address used to refe… |
| Ipv6Address | OCTET STRING (SIZE (16)) | current | This data type is used to model IPv6 addresses. This is a binary string of 16 octets in network byte-order. |
| LldpLinkAggStatusMap | BITS { aggCapable(0), aggEnabled(1) } | current | This TC describes the link aggregation status. The bit 'aggCapable(0)' indicates the link is capable of being aggregated. The bit 'aggEnabled(1)' indicates the link is currently in aggregation. |
| LldpManAddress | OCTET STRING (SIZE (1..31)) | current | The value of a management address associated with the LLDP agent that may be used to reach higher layer entities to assist discovery by network management. It should be noted that appropriate security credentials, such … |
| LldpPortNumber | Integer32(1..4096) | current | Each port contained in the chassis (that is known to the LLDP agent) is uniquely identified by a port number. A port number has no mandatory relationship to an InterfaceIndex object (of the interfaces MIB, IETF RFC 2863… |
| LldpPowerPortClass | INTEGER { pClassPSE(1), pClassPD(2) } | current | This TC describes the Power over Ethernet (PoE) port class. |
| OwnerString | OCTET STRING (SIZE (0..127)) | current | This data type is used to model an administratively assigned name of the owner of a resource. Implementations must accept values composed of well-formed NVT ASCII sequences. In addition, implementations should accept va… |
| PortList | OCTET STRING | current | Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents… |
| RmonStatus | INTEGER { valid(1), createRequest(2), underCreation(3), invalid(4) } | current | The status of a table entry. Setting this object to the value invalid(4) has the effect of invalidating the corresponding entry. That is, it effectively disassociates the mapping identified with said entry. It is an imp… |
| Timeout | INTEGER | current | A STP timer in units of 1/100 seconds To convert a Timeout value into a value in units of 1/256 seconds, the following algorithm should be used: b = floor( (n * 256) / 100) where: floor = quotient [ignore remainder] n i… |
| VlanIndex | Unsigned32 | current | A value used to index per-VLAN tables: values of 0 and 4095 are not permitted; if the value is between 1 and 4094 inclusive, it represents an IEEE 802.1Q VLAN-ID with global scope within a given bridged domain (see Vlan… |