DGS-1210-52_CX
875 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.171 | Noded-link | |||
| 1.3.6.1.4.1.171.10 | Nodedlink-products | |||
| 1.3.6.1.4.1.171.10.76 | Nodedlink-DGS12XXSeriesProd | |||
| 1.3.6.1.4.1.171.10.76.22 | Nodedgs-1210-52 | |||
| 1.3.6.1.4.1.171.10.76.22.1 | Nodedgs-1210-52cx | |||
| 1.3.6.1.4.1.171.10.76.22.1.1 | NodecompanySystem | |||
| 1.3.6.1.4.1.171.10.76.22.1.1.1 | ScalarsysSwitchName | read-write | current | System name used for identification of the device. The following characters are allowed to input. 0 ~ 9 / a ~ z / A ~ Z Special character: ( ) �V + _ = . |
| 1.3.6.1.4.1.171.10.76.22.1.1.2 | ScalarsysHardwareVersion | read-only | current | Version number of the Hardware. |
| 1.3.6.1.4.1.171.10.76.22.1.1.3 | ScalarsysFirmwareVersion | read-only | current | Version number of the Firmware. |
| 1.3.6.1.4.1.171.10.76.22.1.1.4 | ScalarsysLoginTimeoutInterval | read-write | current | This time interval is used to count the time and logout web interface automatically. |
| 1.3.6.1.4.1.171.10.76.22.1.1.5 | ScalarsysLocationName | read-write | current | The location name of this node (e.g., `telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string. |
| 1.3.6.1.4.1.171.10.76.22.1.1.7 | ScalarsysSystemPassword | read-write | current | This object is used to set System Password, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark. |
| 1.3.6.1.4.1.171.10.76.22.1.1.8 | ScalarsysSafeGuardEnable | read-write | current | This object is used to set Safeguard Enable\Disable. |
| 1.3.6.1.4.1.171.10.76.22.1.1.9 | ScalarsysRestart | read-write | current | This object allows the user to restart the Switch (i.e)the entire switch will operationally go down and start again. Setting a value of 'true' causes the switc… |
| 1.3.6.1.4.1.171.10.76.22.1.1.10 | ScalarsysSave | read-write | current | This object is used to save Configuration. |
| 1.3.6.1.4.1.171.10.76.22.1.1.12 | ScalarsysJumboFrameEnable | read-write | current | Gigabit Web Smart Switches support jumbo frames (frames larger than the Ethernet frame size of 1522 bytes) of up to 10,000 bytes (tagged). Default jumbo frame … |
| 1.3.6.1.4.1.171.10.76.22.1.1.13 | TablesysPortCtrlTable | not-accessible | current | A table to control the port specific parameters of the device like speed, duplex mode, etc. |
| 1.3.6.1.4.1.171.10.76.22.1.1.13.1 | RowsysPortCtrlEntry | not-accessible | current | An entry appears in this table for each interface in the system. Index to the table is the interface index of the port. |
| 1.3.6.1.4.1.171.10.76.22.1.1.13.1.1 | ColumnsysPortCtrlIndex | read-only | current | Interface index of the port for the configuration in this entry applies. |
| 1.3.6.1.4.1.171.10.76.22.1.1.13.1.2 | ColumnsysPortCtrlSpeed | read-write | current | Configures interface speed. |
| 1.3.6.1.4.1.171.10.76.22.1.1.13.1.3 | ColumnsysPortCtrlOperStatus | read-only | current | The port's operating speed state. |
| 1.3.6.1.4.1.171.10.76.22.1.1.13.1.4 | ColumnsysPortCtrlMDI | read-write | current | Configures interface auto/mdi/mdix mode. The default setting is Auto. |
| 1.3.6.1.4.1.171.10.76.22.1.1.13.1.5 | ColumnsysPortCtrlFlowControl | read-write | current | Enables / disables flow control for the interface. |
| 1.3.6.1.4.1.171.10.76.22.1.1.13.1.6 | ColumnsysPortCtrlFlowControlOper | read-only | current | The link parner negotiate port's operating flow control state. |
| 1.3.6.1.4.1.171.10.76.22.1.1.13.1.7 | ColumnsysPortCtrlType | read-only | current | The port's media type. |
| 1.3.6.1.4.1.171.10.76.22.1.1.14 | ScalarsysDhcpAutoConfiguration | read-write | current | This object indicates auto config is enabled or disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.1.15 | NodesysGPIOStatus | |||
| 1.3.6.1.4.1.171.10.76.22.1.1.15.1 | ScalarsysFanStatus | read-only | current | The Fan status for this device. |
| 1.3.6.1.4.1.171.10.76.22.1.1.16 | TablesysPortDescriptionTable | not-accessible | current | The port description table. |
| 1.3.6.1.4.1.171.10.76.22.1.1.16.1 | RowsysPortDescriptionEntry | not-accessible | current | The port description entry. |
| 1.3.6.1.4.1.171.10.76.22.1.1.16.1.1 | ColumnsysPortDescIndex | read-only | current | This object indicates the port index. |
| 1.3.6.1.4.1.171.10.76.22.1.1.16.1.2 | ColumnsysPortDescString | read-write | current | This object indicates the port description. |
| 1.3.6.1.4.1.171.10.76.22.1.1.30 | NodesysDdp | |||
| 1.3.6.1.4.1.171.10.76.22.1.1.30.1 | ScalarsysDdpGlobalOnOff | read-write | current | This object indicates D-Link discover protocol is enabled or disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.1.30.2 | ScalarsysDdpGeneralReportOnOff | read-write | current | This object indicates D-Link discover protocol report is enabled or disabled. This object only can be modified when D-Link discover protocol state is enabled. |
| 1.3.6.1.4.1.171.10.76.22.1.1.30.3 | ScalarsysDdpGeneralReportTimer | read-write | current | This object indicates D-Link discover protocol report time period. This object only can be modified when both D-Link discover protocol state and D-Link discove… |
| 1.3.6.1.4.1.171.10.76.22.1.1.30.4 | TablesysDdpProtStatusTable | not-accessible | current | A table to control the port status of D-Link discover protocol. |
| 1.3.6.1.4.1.171.10.76.22.1.1.30.4.1 | RowsysDdpProtStatusEntry | not-accessible | current | An entry appears in this table for each port D-Link discover protocol status. |
| 1.3.6.1.4.1.171.10.76.22.1.1.30.4.1.1 | ColumnsysDdpProtStatusIndex | read-only | current | Interface index of the port for the configuration in this entry applies. |
| 1.3.6.1.4.1.171.10.76.22.1.1.30.4.1.2 | ColumnsysDdpProtStatusControl | read-write | current | Configures the port status of D-Link discover protocol. |
| 1.3.6.1.4.1.171.10.76.22.1.2 | NodecompanyIpifGroup | |||
| 1.3.6.1.4.1.171.10.76.22.1.2.5 | NodeipifSupportV4V6Info | |||
| 1.3.6.1.4.1.171.10.76.22.1.2.5.1 | ScalarsysIpAddrCfgMode | read-write | current | Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'sysDefault… |
| 1.3.6.1.4.1.171.10.76.22.1.2.5.2 | ScalarsysIpAddr | read-write | current | Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored. |
| 1.3.6.1.4.1.171.10.76.22.1.2.5.3 | ScalarsysIpSubnetMask | read-write | current | IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored. |
| 1.3.6.1.4.1.171.10.76.22.1.2.5.4 | ScalarsysGateway | read-write | current | Gateway |
| 1.3.6.1.4.1.171.10.76.22.1.2.5.5 | ScalaripifName | read-only | current | The Description for the interface. |
| 1.3.6.1.4.1.171.10.76.22.1.2.5.7 | Scalaripifv6GlobalStatus | read-create | current | The ID of VLAN that you want this interface to be in. It must be a exist vlan id. |
| 1.3.6.1.4.1.171.10.76.22.1.2.5.8 | Scalaripifv6DHCPStatus | read-create | current | The state of DHCPv6 that you want this interface to be in. It must be a exist vlan id. |
| 1.3.6.1.4.1.171.10.76.22.1.2.5.9 | Scalaripifv6AutolinkloStatus | read-create | current | The global state of link local that you want this interface to be in. It must be a exist vlan id. |
| 1.3.6.1.4.1.171.10.76.22.1.2.5.10 | Scalaripifv6NSRetransmitTime | read-create | current | The NS's retransmit time that you want this interface to be in. It must be a exist vlan id. |
| 1.3.6.1.4.1.171.10.76.22.1.2.5.11 | Scalaripifv6DefaultGateway | read-create | current | The ipv6 default gateway that you want this interface to be in. To delete gateway, please insert address '0000:0000:0000:0000:0000:0000:0000:0000'. |
| 1.3.6.1.4.1.171.10.76.22.1.2.5.12 | TableipifV6AddressTable | not-accessible | current | A list of interface entries. |
| 1.3.6.1.4.1.171.10.76.22.1.2.5.12.1 | RowipifV6AddressEntry | not-accessible | current | An entry containing management information applicable to a particular interface. |
| 1.3.6.1.4.1.171.10.76.22.1.2.5.12.1.1 | ColumnipifV6AddressMainIndex | read-only | current | The index of this IPv6 entry. |
| 1.3.6.1.4.1.171.10.76.22.1.2.5.12.1.2 | ColumnipifV6AddressIpAddr | read-only | current | The ip address of this IPv6 entry. |
| 1.3.6.1.4.1.171.10.76.22.1.2.5.12.1.3 | ColumnipifV6AddressIpPrefix | read-only | current | The ip prefix of this IPv6 entry. |
| 1.3.6.1.4.1.171.10.76.22.1.2.5.12.1.4 | ColumnipifV6AddressIpType | read-only | current | The ip type of this IPv6 entry. |
| 1.3.6.1.4.1.171.10.76.22.1.2.5.12.1.5 | ColumnipifV6AddressRowStatus | read-create | current | The status of an entry in the Multi Interface Table. Only a subset of the rowstatus variables (active, createAndWait, destroy) are available. |
| 1.3.6.1.4.1.171.10.76.22.1.2.6 | ScalardhcpOption12Status | read-write | current | Status of DHCP Option12 |
| 1.3.6.1.4.1.171.10.76.22.1.2.7 | ScalardhcpOption12HostName | read-write | current | Host name in DHCP option 12. The acceptable beginning of DHCP hostname is letter. |
| 1.3.6.1.4.1.171.10.76.22.1.3 | NodecompanyTftpGroup | |||
| 1.3.6.1.4.1.171.10.76.22.1.3.9 | NodetftpFwTargetGroup | |||
| 1.3.6.1.4.1.171.10.76.22.1.3.9.1 | ScalartftpFwTargetServerIpAddress | read-write | current | The TFTP server's IP address is used to upload or download firmware. |
| 1.3.6.1.4.1.171.10.76.22.1.3.9.2 | ScalartftpFwTargetServerIpType | read-write | current | Type of IP interface. |
| 1.3.6.1.4.1.171.10.76.22.1.3.9.3 | ScalartftpFwTargetInterfaceName | read-write | current | Specifies the interface name when the tftpFwTargetServerIpAddress is linklocal address. |
| 1.3.6.1.4.1.171.10.76.22.1.3.9.4 | ScalartftpFwTargetImageFileName | read-write | current | Configure firmware filename to download. |
| 1.3.6.1.4.1.171.10.76.22.1.3.9.5 | ScalartftpFwTargetTftpOperation | read-write | current | The tftp operates to perform downloading the firmware image to the unit. This object is used in conjunction with configBootTftpServerIp and configBootImageFile… |
| 1.3.6.1.4.1.171.10.76.22.1.3.9.6 | ScalartftpFwTargetTftpOperationStatus | read-only | current | The tftp operation status represent firmware backup or upgrade status. |
| 1.3.6.1.4.1.171.10.76.22.1.3.10 | NodetftpCfgTargetGroup | |||
| 1.3.6.1.4.1.171.10.76.22.1.3.10.1 | ScalartftpCfgTargetServerIpAddress | read-write | current | The TFTP server's IP address is used to upload or download configuration file. |
| 1.3.6.1.4.1.171.10.76.22.1.3.10.2 | ScalartftpCfgTargetServerIpType | read-write | current | Type of IP interface. |
| 1.3.6.1.4.1.171.10.76.22.1.3.10.3 | ScalartftpCfgTargetInterfaceName | read-write | current | Specifies the interface name when the tftpCfgTargetServerIpAddress is linklocal address. |
| 1.3.6.1.4.1.171.10.76.22.1.3.10.4 | ScalartftpCfgTargetImageFileName | read-write | current | The configuration filename is used to store or retrieve config from the tftp server. |
| 1.3.6.1.4.1.171.10.76.22.1.3.10.5 | ScalartftpCfgTargetTftpOperation | read-write | current | The tftp operates to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object … |
| 1.3.6.1.4.1.171.10.76.22.1.3.10.6 | ScalartftpCfgTargetTftpOperationStatus | read-only | current | The tftp operation status represent configuration file backup or restore status. |
| 1.3.6.1.4.1.171.10.76.22.1.4 | NodecompanyMiscGroup | |||
| 1.3.6.1.4.1.171.10.76.22.1.4.2 | ScalarmiscReset | read-write | current | Physically resets the unit - use with care. A (1) resets the unit, a (2) does nothing. |
| 1.3.6.1.4.1.171.10.76.22.1.4.3 | ScalarmiscStatisticsReset | read-write | current | Resets the units statistics. A (1) resets the statistics count, a (2) does nothing. |
| 1.3.6.1.4.1.171.10.76.22.1.6 | NodecompanyRSTP | |||
| 1.3.6.1.4.1.171.10.76.22.1.6.1 | NodestpGlobal | |||
| 1.3.6.1.4.1.171.10.76.22.1.6.1.1 | ScalarrstpStatus | read-write | current | The administrative module status requested by management for the RSTP Module. This enables or disables RSTP in the system. A value of 'enabled' (1) indicates t… |
| 1.3.6.1.4.1.171.10.76.22.1.6.1.2 | ScalarstpVersion | read-write | current | The version of Spanning Tree Protocol the bridge is currently running. The value 'stpCompatible(0)' indicates the Spanning Tree Protocol specified in IEEE 802.… |
| 1.3.6.1.4.1.171.10.76.22.1.6.1.3 | ScalarstpPriority | read-write | current | The bridge priority vector, as defined in 17.6. The first (RootBridgeID) and third (DesignatedBridgeID)components are both equal to the value of the Bridge Ide… |
| 1.3.6.1.4.1.171.10.76.22.1.6.1.4 | ScalarstpTxHoldCount | read-write | current | The value used by the Port Transmit state machine to limit the maximum transmission rate. |
| 1.3.6.1.4.1.171.10.76.22.1.6.1.5 | ScalarstpProtocolSpecification | read-only | current | An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE … |
| 1.3.6.1.4.1.171.10.76.22.1.6.1.6 | ScalarstpTimeSinceTopologyChange | read-only | current | The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity. |
| 1.3.6.1.4.1.171.10.76.22.1.6.1.7 | ScalarstpTopChanges | read-only | current | The total number of topology changes detected by this bridge since the management entity was last reset or initialized. |
| 1.3.6.1.4.1.171.10.76.22.1.6.1.8 | ScalarstpDesignatedRoot | read-only | current | The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Ide… |
| 1.3.6.1.4.1.171.10.76.22.1.6.1.9 | ScalarstpRootCost | read-only | current | The cost of the path to the root as seen from this bridge. |
| 1.3.6.1.4.1.171.10.76.22.1.6.1.10 | ScalarstpRootPort | read-only | current | The port number of the port which offers the lowest cost path from this bridge to the root bridge. |
| 1.3.6.1.4.1.171.10.76.22.1.6.1.11 | ScalarstpMaxAge | read-only | current | The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. The root… |
| 1.3.6.1.4.1.171.10.76.22.1.6.1.12 | ScalarstpHelloTime | read-only | current | The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become … |
| 1.3.6.1.4.1.171.10.76.22.1.6.1.13 | ScalarstpHoldTime | read-only | current | This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredth… |
| 1.3.6.1.4.1.171.10.76.22.1.6.1.14 | ScalarstpForwardDelay | read-only | current | This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The… |
| 1.3.6.1.4.1.171.10.76.22.1.6.1.15 | ScalarstpBridgeMaxAge | read-write | current | The Max Age component of designatedTimes (17.19.5). This time value, measured in units of hundredths of a second. BridgeTimes comprises four components�Xthe … |
| 1.3.6.1.4.1.171.10.76.22.1.6.1.16 | ScalarstpBridgeHelloTime | read-write | current | The Hello Time component of designatedTimes (17.19.5). This time value, measured in units of hundredths of a second. BridgeTimes comprises four components�Xt… |
| 1.3.6.1.4.1.171.10.76.22.1.6.1.17 | ScalarstpBridgeForwardDelay | read-write | current | |
| 1.3.6.1.4.1.171.10.76.22.1.6.2 | TablestpPortTable | not-accessible | current | A table that contains port-specific information for the Spanning Tree Protocol. |
| 1.3.6.1.4.1.171.10.76.22.1.6.2.1 | RowstpPortEntry | not-accessible | current | A list of information maintained by every port about the Spanning Tree Protocol state for that port. |
| 1.3.6.1.4.1.171.10.76.22.1.6.2.1.1 | ColumnstpPort | read-only | current | The port number of the port for which this entry contains Spanning Tree Protocol management information. |
| 1.3.6.1.4.1.171.10.76.22.1.6.2.1.2 | ColumnstpPortPriority | read-write | current | The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is … |
| 1.3.6.1.4.1.171.10.76.22.1.6.2.1.3 | ColumnstpPortState | read-only | current | The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the … |
| 1.3.6.1.4.1.171.10.76.22.1.6.2.1.4 | ColumnstpPortEnable | read-write | current | The enabled/disabled status of the port. |
| 1.3.6.1.4.1.171.10.76.22.1.6.2.1.5 | ColumnstpAdminPortPathCost | read-write | current | The contribution of this port to the path cost of paths towards the spanning tree root which include this port. Writing a value of '0' assigns the automaticall… |
| 1.3.6.1.4.1.171.10.76.22.1.6.2.1.6 | ColumnstpPortPathCost | read-only | current | The contribution of this port to the path cost of paths towards the spanning tree root which include this port. |
| 1.3.6.1.4.1.171.10.76.22.1.6.2.1.7 | ColumnstpPortDesignatedRoot | read-only | current | The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the po… |
| 1.3.6.1.4.1.171.10.76.22.1.6.2.1.8 | ColumnstpPortDesignatedCost | read-only | current | The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs. |
| 1.3.6.1.4.1.171.10.76.22.1.6.2.1.9 | ColumnstpPortDesignatedBridge | read-only | current | The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment. |
| 1.3.6.1.4.1.171.10.76.22.1.6.2.1.10 | ColumnstpPortDesignatedPort | read-only | current | The Port Identifier of the port on the Designated Bridge for this port's segment. |
| 1.3.6.1.4.1.171.10.76.22.1.6.2.1.11 | ColumnstpPortForwardTransitions | read-only | current | The number of times this port has transitioned from the Learning state to the Forwarding state. |
| 1.3.6.1.4.1.171.10.76.22.1.6.2.1.12 | ColumnstpPortProtocolMigration | read-write | current | When operating in RSTP (version 2) mode, writing TRUE(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effe… |
| 1.3.6.1.4.1.171.10.76.22.1.6.2.1.13 | ColumnstpPortOperEdgePort | read-only | current | The operational value of the Edge Port parameter. The object is initialized to the value of stpPortAdminEdgePort and is set FALSE on reception of a BPDU. |
| 1.3.6.1.4.1.171.10.76.22.1.6.2.1.14 | ColumnstpPortAdminPointToPoint | read-write | current | The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as… |
| 1.3.6.1.4.1.171.10.76.22.1.6.2.1.15 | ColumnstpPortOperPointToPoint | read-only | current | The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection o… |
| 1.3.6.1.4.1.171.10.76.22.1.6.2.1.16 | ColumnstpPortEdge | read-write | current | This parameter when TRUE(1) indicates that detection of a port as Edge Port happens automatically and FALSE(2) indicates that this feature is disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.6.2.1.17 | ColumnstpPortRestrictedRole | read-write | current | A Boolean value set by management. If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even it has the best spanning tree priorit… |
| 1.3.6.1.4.1.171.10.76.22.1.6.2.1.18 | ColumnstpPortRestrictedTCN | read-write | current | A Boolean value set by management. If TRUE causes the Port not to propagate received topology change notifications and topology changes to other Ports. This pa… |
| 1.3.6.1.4.1.171.10.76.22.1.7 | NodecompanyDot1qVlanGroup | |||
| 1.3.6.1.4.1.171.10.76.22.1.7.2 | Scalardot1qVlanManagementOnOff | read-write | current | Enable/Disable management VLAN mechanism. |
| 1.3.6.1.4.1.171.10.76.22.1.7.3 | Scalardot1qVlanManagementid | read-write | current | The management VLAN ID, which will allow to forward packets of that VLAN to CPU. |
| 1.3.6.1.4.1.171.10.76.22.1.7.5 | Scalardot1qVlanAsyOnOff | read-write | current | Enable/Disable IEEE 802.1Q Asymmetric VLAN |
| 1.3.6.1.4.1.171.10.76.22.1.7.6 | Tabledot1qVlanTable | not-accessible | current | A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and wi… |
| 1.3.6.1.4.1.171.10.76.22.1.7.6.1 | Rowdot1qVlanEntry | not-accessible | current | Information for a VLAN configured into the device by (local or network) management. |
| 1.3.6.1.4.1.171.10.76.22.1.7.6.1.1 | Columndot1qVlanName | read-create | current | An administratively assigned string, which may be used to identify the VLAN. |
| 1.3.6.1.4.1.171.10.76.22.1.7.6.1.2 | Columndot1qVlanEgressPorts | read-create | current | The set of ports which are permanently assigned to the egress list for this VLAN by management. Changes to a bit in this object affect the per-port per-VLAN Re… |
| 1.3.6.1.4.1.171.10.76.22.1.7.6.1.4 | Columndot1qVlanUntaggedPorts | read-create | current | The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (dot1qVlanIndex = 1) is … |
| 1.3.6.1.4.1.171.10.76.22.1.7.6.1.5 | Columndot1qVlanRowStatus | read-create | current | The status of a row in dot1qVlanTable. By setting this object, new entries can be created in dot1qVlanTable and existing entries can be removed from dot1qVlanT… |
| 1.3.6.1.4.1.171.10.76.22.1.7.7 | Tabledot1qVlanPortTable | not-accessible | current | A table containing per port control and status information for VLAN configuration in the device. |
| 1.3.6.1.4.1.171.10.76.22.1.7.7.1 | Rowdot1qVlanPortEntry | not-accessible | current | Information controlling VLAN configuration for a port on the device. |
| 1.3.6.1.4.1.171.10.76.22.1.7.7.1.1 | Columndot1qVlanPvid | read-write | current | The PVID, the VLAN ID assigned to untagged frames or Priority-Tagged frames received on this port. |
| 1.3.6.1.4.1.171.10.76.22.1.7.8 | Tabledot1qVlanUngisterMCFilterTable | not-accessible | current | This table contains the list of ports through which a router, in a particular VLAN is reachable. |
| 1.3.6.1.4.1.171.10.76.22.1.7.8.1 | Rowdot1qVlanUngisterMCFilterEntry | not-accessible | current | A list of multicast filter mode information for each VLAN ID. |
| 1.3.6.1.4.1.171.10.76.22.1.7.8.1.1 | Columndot1qVlanUngisterMCFilterVlanId | read-only | current | Per Vlan to configure multicast filtering function. |
| 1.3.6.1.4.1.171.10.76.22.1.7.8.1.2 | Columndot1qVlanUngisterMCFiltermode | read-write | current | Filter unknown multicast frames or normal operation(i.e. forwarding) |
| 1.3.6.1.4.1.171.10.76.22.1.8 | NodecompanyLA | |||
| 1.3.6.1.4.1.171.10.76.22.1.8.1 | NodelaSystem | |||
| 1.3.6.1.4.1.171.10.76.22.1.8.1.2 | ScalarlaStatus | read-write | current | Sets the Link Aggregation Module administrative status as enabled or disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.8.1.3 | TablelaPortChannelTable | not-accessible | current | A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. Th… |
| 1.3.6.1.4.1.171.10.76.22.1.8.1.3.1 | RowlaPortChannelEntry | not-accessible | current | There is one entry in this table for each created port-channel port. |
| 1.3.6.1.4.1.171.10.76.22.1.8.1.3.1.1 | ColumnlaPortChannelIfIndex | read-only | current | The index of the port-channel(Aggregator's interface index). |
| 1.3.6.1.4.1.171.10.76.22.1.8.1.3.1.2 | ColumnlaPortChannelMemberList | read-write | current | Member Port list of the port channel. Add the ports as a aggregation member associated of a port-channel. |
| 1.3.6.1.4.1.171.10.76.22.1.8.1.3.1.3 | ColumnlaPortChannelMode | read-write | current | Current Operating Channel Mode of the port channel Lacp(1) - forcing the port to negotiate with the partner. manual(2) - force the port to enable channeling (M… |
| 1.3.6.1.4.1.171.10.76.22.1.8.2 | NodelaPortControl | |||
| 1.3.6.1.4.1.171.10.76.22.1.8.2.1 | TablelaPortControlTable | not-accessible | current | A table that contains Link Aggregation Control configuration information about every Aggregation Port associated with this device. A row appears in this table … |
| 1.3.6.1.4.1.171.10.76.22.1.8.2.1.1 | RowlaPortControlEntry | not-accessible | current | A list of Link Aggregation Control configuration parameters for each Aggregation Port on this device. |
| 1.3.6.1.4.1.171.10.76.22.1.8.2.1.1.1 | ColumnlaPortControlIndex | read-only | current | The index of the port. |
| 1.3.6.1.4.1.171.10.76.22.1.8.2.1.1.3 | ColumnlaPortActorActivity | read-write | current | This object indicates LACP_Activity to this Aggregation Port. LACP can be configured in one of two modes: active or passive. In active mode it will always send… |
| 1.3.6.1.4.1.171.10.76.22.1.8.2.1.1.4 | ColumnlaPortActorTimeout | read-write | current | This object indicates LACP_Timeout to this Aggregation Port. short(1) - LACP Timeout 3 seconds. long (2) - LACP Timeout 90 seconds. |
| 1.3.6.1.4.1.171.10.76.22.1.9 | NodecompanyStaticMAC | |||
| 1.3.6.1.4.1.171.10.76.22.1.9.1 | ScalarstaticDisableAutoLearn | read-write | current | Set on to disable Auto Learning Excluding Uplink Port and set off to enable Auto Learning. |
| 1.3.6.1.4.1.171.10.76.22.1.9.2 | ScalarstaticAutoLearningList | read-write | current | The set of the device's member ports that belong to the Static MAC auto learning enable/disable. For example, when Disable Auto Learning is enable, the octet v… |
| 1.3.6.1.4.1.171.10.76.22.1.9.3 | TablestaticTable | not-accessible | current | A list of the Static MACs |
| 1.3.6.1.4.1.171.10.76.22.1.9.3.1 | RowstaticEntry | not-accessible | current | A Static MAC entry containing the mac and forwarding port. |
| 1.3.6.1.4.1.171.10.76.22.1.9.3.1.1 | ColumnstaticVlanID | read-only | current | The VLAN ID of the static MAC entry. |
| 1.3.6.1.4.1.171.10.76.22.1.9.3.1.2 | ColumnstaticMac | read-only | current | The MAC address associated of the static MAC entry. |
| 1.3.6.1.4.1.171.10.76.22.1.9.3.1.3 | ColumnstaticPort | read-only | current | The forwarding port of the static MAC entry. |
| 1.3.6.1.4.1.171.10.76.22.1.9.3.1.4 | ColumnstaticStatus | read-write | current | The status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. The trunk member port ca… |
| 1.3.6.1.4.1.171.10.76.22.1.10 | NodecompanyIgsGroup | |||
| 1.3.6.1.4.1.171.10.76.22.1.10.1 | NodeigsSystem | |||
| 1.3.6.1.4.1.171.10.76.22.1.10.1.1 | ScalarigsStatus | read-write | current | Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module starts protocol operations. When set to 'disabled', the IGS module stops… |
| 1.3.6.1.4.1.171.10.76.22.1.10.1.2 | ScalarigsRouterPortPurgeInterval | read-write | current | This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInter… |
| 1.3.6.1.4.1.171.10.76.22.1.10.1.3 | ScalarigsHostPortPurgeInterval | read-write | current | This is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received this timer runs for 'PortPurg… |
| 1.3.6.1.4.1.171.10.76.22.1.10.1.4 | ScalarigsRobustnessValue | read-write | current | When the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attrib… |
| 1.3.6.1.4.1.171.10.76.22.1.10.1.5 | ScalarigsGrpQueryInterval | read-write | current | The value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there is any intersted receive… |
| 1.3.6.1.4.1.171.10.76.22.1.10.1.6 | ScalarigsQueryInterval | read-write | current | This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for VLANs. |
| 1.3.6.1.4.1.171.10.76.22.1.10.1.7 | ScalarigsQueryMaxResponseTime | read-write | current | The maximum query response time advertised in IGMPv2 general queries on this interface. |
| 1.3.6.1.4.1.171.10.76.22.1.10.1.8 | ScalarigsReportToAllPort | read-write | current | Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module forwards packets to report to all port. When set to 'disabled', the IGS … |
| 1.3.6.1.4.1.171.10.76.22.1.10.3 | NodeigsVlan | |||
| 1.3.6.1.4.1.171.10.76.22.1.10.3.3 | TableigsVlanRouterTable | not-accessible | current | This table contains the list of ports through which a router, in a particular VLAN is reachable. |
| 1.3.6.1.4.1.171.10.76.22.1.10.3.3.1 | RowigsVlanRouterEntry | not-accessible | current | An igs vlan router entry contain the igs vlan router port list. |
| 1.3.6.1.4.1.171.10.76.22.1.10.3.3.1.1 | ColumnigsVlanRouterVlanId | read-only | current | It is the VLAN ID of the igs vlan router entry. |
| 1.3.6.1.4.1.171.10.76.22.1.10.3.3.1.2 | ColumnigsVlanRouterPortList | read-only | current | List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically. |
| 1.3.6.1.4.1.171.10.76.22.1.10.3.4 | TableigsVlanFilterTable | not-accessible | current | This table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.10.3.4.1 | RowigsVlanFilterEntry | not-accessible | current | Contains snooping status , version and fast leave configuration for a specific VLAN. |
| 1.3.6.1.4.1.171.10.76.22.1.10.3.4.1.1 | ColumnigsVlanFilterVlanId | read-only | current | Index of IgsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in IgsVlanFilterEntry is to be done. |
| 1.3.6.1.4.1.171.10.76.22.1.10.3.4.1.2 | ColumnigsVlanSnoopStatus | read-write | current | This object allows you to enable/disable IGS function on a specific VLAN. |
| 1.3.6.1.4.1.171.10.76.22.1.10.3.4.1.3 | ColumnigsVlanQuerier | read-only | current | Indicates whether the switch is configured as a querier in the VLAN |
| 1.3.6.1.4.1.171.10.76.22.1.10.3.4.1.4 | ColumnigsVlanCfgQuerier | read-write | current | The snooping switch can be configured as a querier via this object to send out IGMP general queries when IGMP routers are not present in the VLAN. When set to … |
| 1.3.6.1.4.1.171.10.76.22.1.10.3.4.1.5 | ColumnigsVlanQueryInterval | read-only | current | This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as … |
| 1.3.6.1.4.1.171.10.76.22.1.10.3.4.1.6 | ColumnigsVlanRtrPortList | read-write | current | List of ports which are configured statically as router ports |
| 1.3.6.1.4.1.171.10.76.22.1.10.3.4.1.8 | ColumnigsVlanFastLeave | read-write | current | Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for … |
| 1.3.6.1.4.1.171.10.76.22.1.10.3.5 | TableigsVlanMulticastGroupTable | not-accessible | current | This table contains MAC based multicast forwarding information. |
| 1.3.6.1.4.1.171.10.76.22.1.10.3.5.1 | RowigsVlanMulticastGroupEntry | not-accessible | current | This table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded. |
| 1.3.6.1.4.1.171.10.76.22.1.10.3.5.1.1 | ColumnigsVlanMulticastGroupVlanId | read-only | current | VLAN ID pertaining to the Multicast forwarding entry |
| 1.3.6.1.4.1.171.10.76.22.1.10.3.5.1.2 | ColumnigsVlanMulticastGroupIpAddress | read-only | current | Multicast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format. |
| 1.3.6.1.4.1.171.10.76.22.1.10.3.5.1.3 | ColumnigsVlanMulticastGroupMacAddress | read-only | current | Multicast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format. |
| 1.3.6.1.4.1.171.10.76.22.1.10.3.5.1.4 | ColumnigsVlanMulticastGroupPortList | read-only | current | List of ports onto which the multicast data packets destined for this group will be forwarded. |
| 1.3.6.1.4.1.171.10.76.22.1.12 | NodecompanyQoSGroup | |||
| 1.3.6.1.4.1.171.10.76.22.1.12.1 | ScalarqosMode | read-write | current | Settings of Qos mode: IEEE 802.1p QoS or DSCP QoS or TOS Qos. IEEE 802.1p : It specifies a priority(0~7) value to four queues in WS3 : Low(1,2), Medium(0,3), H… |
| 1.3.6.1.4.1.171.10.76.22.1.12.2 | ScalarqueuingMechanism | read-write | current | Queuing mechanism. strictPriority(1) : Strict Priority wrr(2) : Weighted Round Robin Strict-priority scheduling is implemented with a special strict-priority s… |
| 1.3.6.1.4.1.171.10.76.22.1.12.3 | NodeqosQ1p | |||
| 1.3.6.1.4.1.171.10.76.22.1.12.3.1 | Tabledot1pPortTable | not-accessible | current | A list of 802.1p port default priority Entries. |
| 1.3.6.1.4.1.171.10.76.22.1.12.3.1.1 | Rowdot1pPortEntry | not-accessible | current | A list of 802.1p port default priority priorities. |
| 1.3.6.1.4.1.171.10.76.22.1.12.3.1.1.1 | Columndot1pPortIndex | read-only | current | A port identifier that is in the range of 1 to ifNumber. |
| 1.3.6.1.4.1.171.10.76.22.1.12.3.1.1.2 | Columndot1pPortPriority | read-write | current | For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization. For… |
| 1.3.6.1.4.1.171.10.76.22.1.12.4 | NodeqosDiffServ | |||
| 1.3.6.1.4.1.171.10.76.22.1.12.4.1 | ScalarqosDiffServEnable | read-only | current | Display the DSCP(Differentiated services) function Enabled or Disabled. Notice : DiffServ Type is 2~7 bits in the TOS field. ex: If the DiffServ Type = 000011(… |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2 | NodeqosDiffServTypeGroup | |||
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.1 | ScalarqosDiffServType00 | read-write | current | DiffServ Type 0 : IP ToS value = 0 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.2 | ScalarqosDiffServType01 | read-write | current | DiffServ Type 01 : IP ToS value = 4 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.3 | ScalarqosDiffServType02 | read-write | current | DiffServ Type 02 : IP ToS value = 8 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.4 | ScalarqosDiffServType03 | read-write | current | DiffServ Type 03 : IP ToS value = 12 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.5 | ScalarqosDiffServType04 | read-write | current | DiffServ Type 04 : IP ToS value = 16 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.6 | ScalarqosDiffServType05 | read-write | current | DiffServ Type 05 : IP ToS value = 20 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.7 | ScalarqosDiffServType06 | read-write | current | DiffServ Type 06 : IP ToS value = 24 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.8 | ScalarqosDiffServType07 | read-write | current | DiffServ Type 07 : IP ToS value = 28 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.9 | ScalarqosDiffServType08 | read-write | current | DiffServ Type 08 : IP ToS value = 32 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.10 | ScalarqosDiffServType09 | read-write | current | DiffServ Type 09 : IP ToS value = 36 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.11 | ScalarqosDiffServType10 | read-write | current | DiffServ Type 10 : IP ToS value = 40 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.12 | ScalarqosDiffServType11 | read-write | current | DiffServ Type 11 : IP ToS value = 44 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.13 | ScalarqosDiffServType12 | read-write | current | DiffServ Type 12 : IP ToS value = 48 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.14 | ScalarqosDiffServType13 | read-write | current | DiffServ Type 13 : IP ToS value = 52 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.15 | ScalarqosDiffServType14 | read-write | current | DiffServ Type 14 : IP ToS value = 56 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.16 | ScalarqosDiffServType15 | read-write | current | DiffServ Type 15 : IP ToS value = 60 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.17 | ScalarqosDiffServType16 | read-write | current | DiffServ Type 16 : IP ToS value = 64 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.18 | ScalarqosDiffServType17 | read-write | current | DiffServ Type 17 : IP ToS value = 68 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.19 | ScalarqosDiffServType18 | read-write | current | DiffServ Type 18 : IP ToS value = 72 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.20 | ScalarqosDiffServType19 | read-write | current | DiffServ Type 19 : IP ToS value = 76 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.21 | ScalarqosDiffServType20 | read-write | current | DiffServ Type 20 : IP ToS value = 80 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.22 | ScalarqosDiffServType21 | read-write | current | DiffServ Type 21 : IP ToS value = 84 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.23 | ScalarqosDiffServType22 | read-write | current | DiffServ Type 22 : IP ToS value = 88 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.24 | ScalarqosDiffServType23 | read-write | current | DiffServ Type 23 : IP ToS value = 92 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.25 | ScalarqosDiffServType24 | read-write | current | DiffServ Type 24 : IP ToS value = 96 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.26 | ScalarqosDiffServType25 | read-write | current | DiffServ Type 25 : IP ToS value = 100 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.27 | ScalarqosDiffServType26 | read-write | current | DiffServ Type 26 : IP ToS value = 104 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.28 | ScalarqosDiffServType27 | read-write | current | DiffServ Type 27 : IP ToS value = 108 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.29 | ScalarqosDiffServType28 | read-write | current | DiffServ Type 28 : IP ToS value = 112 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.30 | ScalarqosDiffServType29 | read-write | current | DiffServ Type 29 : IP ToS value = 116 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.31 | ScalarqosDiffServType30 | read-write | current | DiffServ Type 30 : IP ToS value = 120 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.32 | ScalarqosDiffServType31 | read-write | current | DiffServ Type 31 : IP ToS value = 124 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.33 | ScalarqosDiffServType32 | read-write | current | DiffServ Type 32 : IP ToS value = 128 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.34 | ScalarqosDiffServType33 | read-write | current | DiffServ Type 33 : IP ToS value = 132 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.35 | ScalarqosDiffServType34 | read-write | current | DiffServ Type 34 : IP ToS value = 136 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.36 | ScalarqosDiffServType35 | read-write | current | DiffServ Type 35 : IP ToS value = 140 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.37 | ScalarqosDiffServType36 | read-write | current | DiffServ Type 36 : IP ToS value = 144 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.38 | ScalarqosDiffServType37 | read-write | current | DiffServ Type 37 : IP ToS value = 148 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.39 | ScalarqosDiffServType38 | read-write | current | DiffServ Type 38 : IP ToS value = 152 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.40 | ScalarqosDiffServType39 | read-write | current | DiffServ Type 39 : IP ToS value = 156 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.41 | ScalarqosDiffServType40 | read-write | current | DiffServ Type 40 : IP ToS value = 160 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.42 | ScalarqosDiffServType41 | read-write | current | DiffServ Type 41 : IP ToS value = 164 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.43 | ScalarqosDiffServType42 | read-write | current | DiffServ Type 42 : IP ToS value = 168 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.44 | ScalarqosDiffServType43 | read-write | current | DiffServ Type 43 : IP ToS value = 172 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.45 | ScalarqosDiffServType44 | read-write | current | DiffServ Type 44 : IP ToS value = 176 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.46 | ScalarqosDiffServType45 | read-write | current | DiffServ Type 45 : IP ToS value = 180 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.47 | ScalarqosDiffServType46 | read-write | current | DiffServ Type 46 : IP ToS value = 184 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.48 | ScalarqosDiffServType47 | read-write | current | DiffServ Type 47 : IP ToS value = 188 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.49 | ScalarqosDiffServType48 | read-write | current | DiffServ Type 48 : IP ToS value = 192 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.50 | ScalarqosDiffServType49 | read-write | current | DiffServ Type 49 : IP ToS value = 196 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.51 | ScalarqosDiffServType50 | read-write | current | DiffServ Type 50 : IP ToS value = 200 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.52 | ScalarqosDiffServType51 | read-write | current | DiffServ Type 51 : IP ToS value = 204 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.53 | ScalarqosDiffServType52 | read-write | current | DiffServ Type 52 : IP ToS value = 208 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.54 | ScalarqosDiffServType53 | read-write | current | DiffServ Type 53 : IP ToS value = 212 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.55 | ScalarqosDiffServType54 | read-write | current | DiffServ Type 54 : IP ToS value = 216 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.56 | ScalarqosDiffServType55 | read-write | current | DiffServ Type 55 : IP ToS value = 220 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.57 | ScalarqosDiffServType56 | read-write | current | DiffServ Type 56 : IP ToS value = 224 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.58 | ScalarqosDiffServType57 | read-write | current | DiffServ Type 57 : IP ToS value = 228 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.59 | ScalarqosDiffServType58 | read-write | current | DiffServ Type 58 : IP ToS value = 232 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.60 | ScalarqosDiffServType59 | read-write | current | DiffServ Type 59 : IP ToS value = 236 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.61 | ScalarqosDiffServType60 | read-write | current | DiffServ Type 60 : IP ToS value = 240 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.62 | ScalarqosDiffServType61 | read-write | current | DiffServ Type 61 : IP ToS value = 244 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.63 | ScalarqosDiffServType62 | read-write | current | DiffServ Type 62 : IP ToS value = 248 |
| 1.3.6.1.4.1.171.10.76.22.1.12.4.2.64 | ScalarqosDiffServType63 | read-write | current | DiffServ Type 63 : IP ToS value = 252 |
| 1.3.6.1.4.1.171.10.76.22.1.12.5 | NodeqosTOS | |||
| 1.3.6.1.4.1.171.10.76.22.1.12.5.1 | ScalarqosTOSEnable | read-only | current | Display the TOS(Type of services) function Enabled or Disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.12.5.2 | NodeqosTOSGroup | |||
| 1.3.6.1.4.1.171.10.76.22.1.12.5.2.1 | ScalarqosTOSType00 | read-write | current | TOS 0 |
| 1.3.6.1.4.1.171.10.76.22.1.12.5.2.2 | ScalarqosTOSType01 | read-write | current | TOS 01 |
| 1.3.6.1.4.1.171.10.76.22.1.12.5.2.3 | ScalarqosTOSType02 | read-write | current | TOS 02 |
| 1.3.6.1.4.1.171.10.76.22.1.12.5.2.4 | ScalarqosTOSType03 | read-write | current | TOS 03 |
| 1.3.6.1.4.1.171.10.76.22.1.12.5.2.5 | ScalarqosTOSType04 | read-write | current | TOS 04 |
| 1.3.6.1.4.1.171.10.76.22.1.12.5.2.6 | ScalarqosTOSType05 | read-write | current | TOS 05 |
| 1.3.6.1.4.1.171.10.76.22.1.12.5.2.7 | ScalarqosTOSType06 | read-write | current | TOS 06 |
| 1.3.6.1.4.1.171.10.76.22.1.12.5.2.8 | ScalarqosTOSType07 | read-write | current | TOS 07 |
| 1.3.6.1.4.1.171.10.76.22.1.13 | NodecompanyTrafficMgmt | |||
| 1.3.6.1.4.1.171.10.76.22.1.13.1 | NodebandwidthCtrlSettings | |||
| 1.3.6.1.4.1.171.10.76.22.1.13.1.2 | TablebandwidthCtrlTable | not-accessible | current | A table to control the rate limiting parameters either for the entire switch or for each interface in the switch. |
| 1.3.6.1.4.1.171.10.76.22.1.13.1.2.1 | RowbandwidthCtrlEntry | not-accessible | current | An entry appears in this table for each physical interface in the switch. |
| 1.3.6.1.4.1.171.10.76.22.1.13.1.2.1.1 | ColumnbandwidthCtrlIndex | read-only | current | The interface index for which the configuration in this entry applies. |
| 1.3.6.1.4.1.171.10.76.22.1.13.1.2.1.2 | ColumnbandwidthCtrlTxThreshold | read-write | current | Configures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed.… |
| 1.3.6.1.4.1.171.10.76.22.1.13.1.2.1.3 | ColumnbandwidthCtrlRxThreshold | read-write | current | Allows to configure the limiting value for the maximum number of receive packets that can be transmitted per second over this interface. Setting this object to… |
| 1.3.6.1.4.1.171.10.76.22.1.13.3 | NodebroadcastStormCtrlSettings | |||
| 1.3.6.1.4.1.171.10.76.22.1.13.3.1 | ScalarbroadcastStormCtrlGlobalOnOff | read-write | current | This object indicates storm control function is enabled or disabled for device. When you enable broadcast storm control function, D-Link Smart Switches will al… |
| 1.3.6.1.4.1.171.10.76.22.1.13.3.2 | ScalarbroadcastStormCtrlLimitType | read-write | current | This object indicates storm control function is control broadcast packet or multicast packet or dlf packet. |
| 1.3.6.1.4.1.171.10.76.22.1.13.3.3 | ScalarbroadcastStormCtrlThreshold | read-write | current | Allows to configure the limiting value for the maximum number of Kbits/sec that can be transmitted per second over this interface. Setting this object to the v… |
| 1.3.6.1.4.1.171.10.76.22.1.14 | NodecompanySecurity | |||
| 1.3.6.1.4.1.171.10.76.22.1.14.1 | NodesecurityTrustedHost | |||
| 1.3.6.1.4.1.171.10.76.22.1.14.1.1 | ScalartrustedHostStatus | read-write | current | This object indicates trusted host function is enabled or disabled. When trusted host function is enabled, D-Link Smart Switches will only allow hosts which yo… |
| 1.3.6.1.4.1.171.10.76.22.1.14.1.3 | TabletrustedHostTable | not-accessible | current | A table to configure trusted host for in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.14.1.3.1 | RowtrustedHostEntry | not-accessible | current | Each entry in this table represents rules for particular trusted host. |
| 1.3.6.1.4.1.171.10.76.22.1.14.1.3.1.1 | ColumntrustedHostIPType | read-only | current | Type of IP interface. |
| 1.3.6.1.4.1.171.10.76.22.1.14.1.3.1.2 | ColumntrustedHostIpAddr | read-only | current | The IP address of host you allow to access to D-Link Smart Switch. Your local host IPv4/6 Addresses must be one of the IP Addresses to avoid disconnection. |
| 1.3.6.1.4.1.171.10.76.22.1.14.1.3.1.3 | ColumntrustedHostIpMask | read-only | current | Used to mask with IPv4/6 address, it allow you set a subnet as a trusted host entry. |
| 1.3.6.1.4.1.171.10.76.22.1.14.1.3.1.4 | ColumntrustedHostRowStatus | read-create | current | The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. IPv4 Trust Host create… |
| 1.3.6.1.4.1.171.10.76.22.1.14.2 | NodesecurityPortSecurity | |||
| 1.3.6.1.4.1.171.10.76.22.1.14.2.1 | TableportSecTable | not-accessible | current | A table to control port security features of the device. |
| 1.3.6.1.4.1.171.10.76.22.1.14.2.1.1 | RowportSecEntry | not-accessible | current | An entry appears in port security table for each interface in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.14.2.1.1.1 | ColumnportSecIndex | read-only | current | The interface index for which the configuration in this entry applies. |
| 1.3.6.1.4.1.171.10.76.22.1.14.2.1.1.2 | ColumnportSecState | read-write | current | Enable / disable port security admin state for the interface. A given ports' dynamic MAC address learning will be stopped such that the current source MAC addr… |
| 1.3.6.1.4.1.171.10.76.22.1.14.2.1.1.3 | ColumnportSecMLA | read-write | current | Configures interface port security maximum learning address numbers. When given ports' admin state is enabled, allows forwarding table learning address number.… |
| 1.3.6.1.4.1.171.10.76.22.1.14.3 | NodesecurityARPSpoofPrevent | |||
| 1.3.6.1.4.1.171.10.76.22.1.14.3.1 | TableaRPSpoofPreventTable | not-accessible | current | A table to control ARP Spoofing prevention for the entire switch or for each interface in the switch. |
| 1.3.6.1.4.1.171.10.76.22.1.14.3.1.1 | RowaRPSpoofPreventEntry | not-accessible | current | An entry appears in this table for each interface in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.14.3.1.1.1 | ColumnaRPSpoofPreventIpAddr | not-accessible | current | Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'. |
| 1.3.6.1.4.1.171.10.76.22.1.14.3.1.1.2 | ColumnaRPSpoofPreventMacAddress | read-write | current | Ethernet Mac Address. |
| 1.3.6.1.4.1.171.10.76.22.1.14.3.1.1.3 | ColumnaRPSpoofPreventPortList | read-write | current | Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch throug… |
| 1.3.6.1.4.1.171.10.76.22.1.14.3.1.1.4 | ColumnaRPSpoofPreventRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.10.76.22.1.14.5 | NodesecuritySSL | |||
| 1.3.6.1.4.1.171.10.76.22.1.14.5.1 | ScalarsslSecurityHttpStatus | read-write | current | This object is for enabling or disabling secure HTTP in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.14.5.2 | NodesslCiphers | |||
| 1.3.6.1.4.1.171.10.76.22.1.14.5.2.1 | ScalarsslCipherSuiteList | read-write | current | This object is to configure the cipher-suites list. |
| 1.3.6.1.4.1.171.10.76.22.1.14.7 | NodesecurityDhcpServerScreen | |||
| 1.3.6.1.4.1.171.10.76.22.1.14.7.1 | ScalardhcpServerScreenEnablePortlist | read-write | current | To enable or disable DHCP Server Screening port list. |
| 1.3.6.1.4.1.171.10.76.22.1.14.7.3 | TabledhcpServerScreenTrustedServerTable | not-accessible | current | A table that contains the configuration objects for the DHCP server screen server list. An entry appears in this table for each port that may authenticate acce… |
| 1.3.6.1.4.1.171.10.76.22.1.14.7.3.1 | RowdhcpServerScreenTrustedServerEntry | not-accessible | current | The configuration information for an DHCP server screen server. |
| 1.3.6.1.4.1.171.10.76.22.1.14.7.3.1.1 | ColumndhcpServerScreenTrustedServerIndex | read-only | current | A unique value for DHCP server screen server index. Its value ranges between 1 and 5. |
| 1.3.6.1.4.1.171.10.76.22.1.14.7.3.1.2 | ColumndhcpServerScreenTrustedServerAddress | read-write | current | The IP address of the DHCP server screen server referred to in this table entry. |
| 1.3.6.1.4.1.171.10.76.22.1.14.7.3.1.3 | ColumndhcpServerScreenIPType | read-write | current | Type of IP interface. |
| 1.3.6.1.4.1.171.10.76.22.1.14.7.3.1.4 | ColumndhcpServerScreenTrustedServerStatus | read-create | current | The status of this conceptual row in the swAuthRadiusServerTable. An entry in this table is not qualified for activation until instances of all corresponding c… |
| 1.3.6.1.4.1.171.10.76.22.1.14.8 | NodesecuritySSH | |||
| 1.3.6.1.4.1.171.10.76.22.1.14.8.1 | ScalarsshSecurityStatus | read-write | current | This object is for enabling or disabling ssh in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.14.8.2 | ScalarsshMaxAuthFailAttempts | read-write | current | This object indicates the max auth fail retry attempt times. |
| 1.3.6.1.4.1.171.10.76.22.1.14.8.3 | ScalarsshSessionKeyRekeying | read-write | current | This object indicates one SSH session rekey time interval. |
| 1.3.6.1.4.1.171.10.76.22.1.14.8.4 | ScalarsshMaxSession | read-write | current | This object indicates max SSH session number supported in system. |
| 1.3.6.1.4.1.171.10.76.22.1.14.8.5 | ScalarsshConnectionTimeout | read-write | current | This object indicates SSH connection timeout value. |
| 1.3.6.1.4.1.171.10.76.22.1.14.8.6 | ScalarsshAuthenMethodPassWordAdmin | read-only | current | The object indicates authen method password is enabled or disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.14.8.7 | ScalarsshAuthenMethodPubKeyAdmin | read-only | current | The object indicates authen method public-key is enabled or disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.14.8.8 | ScalarsshAuthenMethodHostKeyAdmin | read-only | current | The object indicates authen method host-key is enabled or disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.14.8.9 | ScalarsshCipherSuiteList | read-only | current | This object is to configure the cipher-suites list. |
| 1.3.6.1.4.1.171.10.76.22.1.14.8.10 | ScalarsshMacSuiteList | read-write | current | This object is to configure the MAC-list. |
| 1.3.6.1.4.1.171.10.76.22.1.14.8.11 | ScalarsshPublKeyRSAAdmin | read-only | current | The object indicates Public key generating algorithm RSA is enabled or disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.14.8.12 | TablesshUserInfoTable | not-accessible | current | A table to configure SSH user auth in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.14.8.12.1 | RowsshUserInfoEntry | not-accessible | current | An entry to configure user auth in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.14.8.12.1.1 | ColumnsshUserInfoID | read-only | current | The ssh user ID associated with the SSH user Info. entry (ID number of SSH user). |
| 1.3.6.1.4.1.171.10.76.22.1.14.8.12.1.2 | ColumnsshUserInfoUserName | read-only | current | The ssh user name associated with the SSH user Info. entry (e.g., `admin, user'). |
| 1.3.6.1.4.1.171.10.76.22.1.14.8.12.1.3 | ColumnsshUserInfoAuth | read-write | current | The object indicates which auth used by the user. |
| 1.3.6.1.4.1.171.10.76.22.1.14.8.12.1.4 | ColumnsshUserInfoHostName | read-write | current | The ssh host name associated with the SSH user Info. entry (e.g., `DUT1, DUT2'). |
| 1.3.6.1.4.1.171.10.76.22.1.14.8.12.1.5 | ColumnsshUserInfoHostIp | read-write | current | SSH HostBased IP Address of the system. Set '0.0.0.0' to disable SSH hostBased IP address check. |
| 1.3.6.1.4.1.171.10.76.22.1.14.8.12.1.6 | ColumnsshUserInfoHostIpv6 | read-write | current | SSH HostBased IPv6 Address of the system. Set '0000:0000:0000:0000:0000:0000:0000:0000' or empty string to disable SSH hostBased IPv6 address check. |
| 1.3.6.1.4.1.171.10.76.22.1.14.9 | NodesecurityTrafficSeg | |||
| 1.3.6.1.4.1.171.10.76.22.1.14.9.1 | ScalartrafficSegStatus | read-write | current | Enable/Disable Status of Traffic Segmention. |
| 1.3.6.1.4.1.171.10.76.22.1.14.9.2 | TabletrafficSegTable | not-accessible | current | A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. Th… |
| 1.3.6.1.4.1.171.10.76.22.1.14.9.2.1 | RowtrafficSegEntry | not-accessible | current | There is one entry in this table for each created port-channel port |
| 1.3.6.1.4.1.171.10.76.22.1.14.9.2.1.1 | ColumntrafficSegIfIndex | read-only | current | The port index of Traffic Segmentation table. |
| 1.3.6.1.4.1.171.10.76.22.1.14.9.2.1.2 | ColumntrafficSegMemberList | read-write | current | Forwarding member port list of Traffic Segmentation port index. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10 | NodesecurityIpMacPortBinding | |||
| 1.3.6.1.4.1.171.10.76.22.1.14.10.1 | TableimpbSettingTable | not-accessible | current | A table to control IP-MAC-Port Binding Setting features of the device. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.1.1 | RowimpbSettingEntry | not-accessible | current | An entry appears in IP-MAC-Port Binding Setting table for each interface in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.1.1.1 | ColumnimpbPortIndex | read-only | current | Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch throug… |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.1.1.2 | ColumnimpbPortState | read-write | current | Disable / enable IP-MAC-Port Binding admin state for the interface. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.1.1.3 | ColumnimpbInsIpPacPortState | read-write | current | Enable / disable IP-MAC-Port Binding also inspect IP packets state for the interface. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.1.1.4 | ColumnimpbDHCPPortState | read-write | current | Disable / enable IP-MAC-Port Binding DHCP snooping state for the interface. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.2 | TableimpbSmartTable | not-accessible | current | A table to control Smart IP-MAC-Port Binding features of the device. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.2.1 | RowimpbSmartEntry | not-accessible | current | An entry appears in Smart IP-MAC-Port Binding table for each interface in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.2.1.1 | ColumnimpbSmartMacAddress | read-only | current | The MAC address associated of the smart IP-MAC-PORT Binding entry. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.2.1.2 | ColumnimpbSmartPort | read-only | current | The port number of the smart IP-MAC-PORT Binding entry. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.2.1.3 | ColumnimpbSmartIpAddress | read-only | current | The IP address associated of the smart IP-MAC-PORT Binding entry. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.2.1.4 | ColumnimpbSmartVlanId | read-only | current | The VLAN ID of the smart IP-MAC-PORT Binding entry. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.2.1.5 | ColumnimpbSmartBinding | read-write | current | Disable / enable IP-MAC-Port Binding for the interface. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.3 | TableimpbWhiteListTable | not-accessible | current | A table to control Manual IP-MAC-Port Binding white list features of the device. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.3.1 | RowimpbWhiteListEntry | not-accessible | current | An entry appears in Manual IP-MAC-Port Binding white list table for each interface in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.3.1.1 | ColumnimpbWhiteListIpAddress | read-only | current | The IP address associated of the Manual IP-MAC-PORT Binding white list entry. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.3.1.2 | ColumnimpbWhiteListMacAddress | read-only | current | The MAC address associated of the Manual IP-MAC-PORT Binding white list entry. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.3.1.3 | ColumnimpbWhiteListPort | read-write | current | The port number of the Manual IP-MAC-PORT Binding white list entry. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.3.1.4 | ColumnimpbWhiteListRowStatus | read-create | current | The status of a row in impbWhiteListTable. By setting this object, new entries can be created in impbWhiteListTable and existing entries can be removed from im… |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.4 | TableimpbBlackListTable | not-accessible | current | A table to control IP-MAC-Port Binding black list of the device. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.4.1 | RowimpbBlackListEntry | not-accessible | current | An entry appears in Manual IP-MAC-Port Binding black list table for each interface in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.4.1.1 | ColumnimpbBlackListMacAddress | read-only | current | The MAC address associated of the IP-MAC-PORT Binding black list entry. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.4.1.2 | ColumnimpbBlackListVlanId | read-only | current | The VLAN ID of the IP-MAC-PORT Binding black list entry. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.4.1.3 | ColumnimpbBlackListPort | read-only | current | The port number of the IP-MAC-PORT Binding black list entry. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.4.1.4 | ColumnimpbBlackListIpAddress | read-only | current | The IP address associated of the IP-MAC-PORT Binding black list entry. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.4.1.5 | ColumnimpbBlackListStatus | read-write | current | nothing/delete IP-MAC-Port Binding for the interface. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.5 | ScalarimpbAutoScanIpAddressFrom | read-write | current | The begin for IP address associated of the IP-MAC-PORT Binding auto scan entry. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.6 | ScalarimpbAutoScanIpAddressTo | read-write | current | The end for IP address associated of the IP-MAC-PORT Binding auto scan entry. |
| 1.3.6.1.4.1.171.10.76.22.1.14.10.7 | ScalarimpbAutoScanStatus | read-write | current | Nothing / scan IP-MAC-Port Binding auto scan for the interface. |
| 1.3.6.1.4.1.171.10.76.22.1.15 | NodecompanyACLGroup | |||
| 1.3.6.1.4.1.171.10.76.22.1.15.1 | NodeaclProfile | |||
| 1.3.6.1.4.1.171.10.76.22.1.15.1.1 | TableaclProfileTable | not-accessible | current | A table to ACL profile . |
| 1.3.6.1.4.1.171.10.76.22.1.15.1.1.1 | RowaclProfileEntry | not-accessible | current | Each entry in this table is a ACL profile. Index to the table is ACL profile ID. |
| 1.3.6.1.4.1.171.10.76.22.1.15.1.1.1.1 | ColumnaclProfileNo | read-only | current | The ACL Profile ID. The ID 1 to 50 is user-defined ACL, and the ID more than 50 is reserved for system-defined ACL. The user only allow to create user-defined … |
| 1.3.6.1.4.1.171.10.76.22.1.15.1.1.1.2 | ColumnaclProfileName | read-write | current | An administratively assigned string, which may be used to identify the Profile. |
| 1.3.6.1.4.1.171.10.76.22.1.15.1.1.1.3 | ColumnaclProfileType | read-write | current | The ACL Profile type, possible value are l2 (1) - for MAC-based rule, l3v4 (2) - for IPv4-based rule, l3v4Ext (3) - for IPv4-Ext rule, l3v6 (4) - for IPv6-base… |
| 1.3.6.1.4.1.171.10.76.22.1.15.1.1.1.4 | ColumnaclProfileRuleCount | read-only | current | The number of rules in this profile. |
| 1.3.6.1.4.1.171.10.76.22.1.15.1.1.1.14 | ColumnaclProfileStatus | read-write | current | This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait… |
| 1.3.6.1.4.1.171.10.76.22.1.15.2 | NodeaclL2Rule | |||
| 1.3.6.1.4.1.171.10.76.22.1.15.2.1 | TableaclL2RuleTable | not-accessible | current | A table to configure L2 filter rules in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.15.2.1.1 | RowaclL2RuleEntry | not-accessible | current | Each entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID. |
| 1.3.6.1.4.1.171.10.76.22.1.15.2.1.1.1 | ColumnaclL2AccessID | read-only | current | L2 Filter rule ID. |
| 1.3.6.1.4.1.171.10.76.22.1.15.2.1.1.2 | ColumnaclL2ProfileID | read-only | current | ACL Profile ID which this rule join. |
| 1.3.6.1.4.1.171.10.76.22.1.15.2.1.1.3 | ColumnaclL2RuleEtherType | read-write | current | The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '-1', which means the rule don't ca… |
| 1.3.6.1.4.1.171.10.76.22.1.15.2.1.1.4 | ColumnaclL2RuleDstMacAddr | read-write | current | Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero,which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.76.22.1.15.2.1.1.5 | ColumnaclL2RuleSrcMacAddr | read-write | current | Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero, which means the rule don't care this condition.. address |
| 1.3.6.1.4.1.171.10.76.22.1.15.2.1.1.6 | ColumnaclL2RuleVlanId | read-write | current | Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule… |
| 1.3.6.1.4.1.171.10.76.22.1.15.2.1.1.7 | ColumnaclL2Rule1pPriority | read-write | current | 802.1p priority to be matched with the packet. By Default, the value will be '-1', which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.76.22.1.15.2.1.1.8 | ColumnaclL2RuleDstMacAddrMask | read-write | current | The MAC address Mask work for Destination MAC address. |
| 1.3.6.1.4.1.171.10.76.22.1.15.2.1.1.9 | ColumnaclL2RuleSrcMacAddrMask | read-write | current | The MAC address Mask work for Source MAC address. |
| 1.3.6.1.4.1.171.10.76.22.1.15.2.1.1.10 | ColumnaclL2RuleAction | read-write | current | Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding r… |
| 1.3.6.1.4.1.171.10.76.22.1.15.2.1.1.12 | ColumnaclL2RulePriority | read-write | current | Enter a priority value if you want to re-write the 802.1p user priority of a packet to the value entered in the Priority field, which meets the criteria specif… |
| 1.3.6.1.4.1.171.10.76.22.1.15.2.1.1.13 | ColumnaclL2RuleReplacePriority | read-write | current | Enable this option and manually enter the replacement value used to re-write the 802.1p user priority value entered in the Priority field, which meets the crit… |
| 1.3.6.1.4.1.171.10.76.22.1.15.2.1.1.99 | ColumnaclL2RuleStatus | read-write | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.76.22.1.15.3 | NodeaclL3v4Rule | |||
| 1.3.6.1.4.1.171.10.76.22.1.15.3.1 | TableaclL3v4RuleTable | not-accessible | current | A table to configure L3 filter rules in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.15.3.1.1 | RowaclL3v4RuleEntry | not-accessible | current | Each entry in this table is a L3 filter rule. Index to the table is L3 filter number. |
| 1.3.6.1.4.1.171.10.76.22.1.15.3.1.1.1 | ColumnaclL3v4RuleAccessID | read-only | current | L3 Filter rule ID. |
| 1.3.6.1.4.1.171.10.76.22.1.15.3.1.1.2 | ColumnaclL3v4RuleProfileNo | read-only | current | The Profile ID which this rule join. |
| 1.3.6.1.4.1.171.10.76.22.1.15.3.1.1.3 | ColumnaclL3v4RuleDstIpAddr | read-write | current | Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.76.22.1.15.3.1.1.4 | ColumnaclL3v4RuleSrcIpAddr | read-write | current | Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.76.22.1.15.3.1.1.5 | ColumnaclL3v4RuleDstIpAddrMask | read-write | current | The IP subnet mask for Destination IP address. |
| 1.3.6.1.4.1.171.10.76.22.1.15.3.1.1.6 | ColumnaclL3v4RuleSrcIpAddrMask | read-write | current | The IP subnet mask for Source IP address. |
| 1.3.6.1.4.1.171.10.76.22.1.15.3.1.1.7 | ColumnaclL3v4RuleAction | read-write | current | Specifies the action to be taken on the packet if the filter rule matches. |
| 1.3.6.1.4.1.171.10.76.22.1.15.3.1.1.9 | ColumnaclL3v4RulePriority | read-write | current | Enter a priority value if you want to re-write the 802.1p user priority of a packet to the value entered in the Priority field, which meets the criteria specif… |
| 1.3.6.1.4.1.171.10.76.22.1.15.3.1.1.10 | ColumnaclL3v4RuleReplacePriority | read-write | current | Enable this option and manually enter the replacement value used to re-write the 802.1p user priority value entered in the Priority field, which meets the crit… |
| 1.3.6.1.4.1.171.10.76.22.1.15.3.1.1.99 | ColumnaclL3v4RuleStatus | read-write | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.76.22.1.15.4 | NodeaclL3v4ExtRule | |||
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1 | TableaclL3v4ExtRuleTable | not-accessible | current | A table to configure L3 filter rules in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1 | RowaclL3v4ExtRuleEntry | not-accessible | current | Each entry in this table is a L3 filter rule. Index to the table is L3 filter number. |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.1 | ColumnaclL3v4ExtRuleAccessID | read-only | current | L3 Filter rule ID. |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.2 | ColumnaclL3v4ExtRuleProfileNo | read-only | current | The Profile ID which this rule join. |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.3 | ColumnaclL3v4ExtRuleProtocol | read-write | current | The type of protocol to be checked against the packet. |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.4 | ColumnaclL3v4ExtRuleICMPMessageType | read-write | current | The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action s… |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.5 | ColumnaclL3v4ExtRuleICMPMessageCode | read-write | current | The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action s… |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.6 | ColumnaclL3v4ExtRuleDstIpAddr | read-write | current | Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.7 | ColumnaclL3v4ExtRuleSrcIpAddr | read-write | current | Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.8 | ColumnaclL3v4ExtRuleDstIpAddrMask | read-write | current | The IP subnet mask for Destination IP address. |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.9 | ColumnaclL3v4ExtRuleSrcIpAddrMask | read-write | current | The IP subnet mask for Source IP address. |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.10 | ColumnaclL3v4ExtRuleTcpUdpDstPort | read-write | current | The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.11 | ColumnaclL3v4ExtRuleTcpUdpSrcPort | read-write | current | The TCP / UDP source port. The default value is -1, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.12 | ColumnaclL3v4ExtRuleTcpUdpDstPortMask | read-write | current | The TCP / UDP Destination port Mask. |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.13 | ColumnaclL3v4ExtRuleTcpUdpSrcPortMask | read-write | current | The TCP / UDP Source port Mask. |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.20 | ColumnaclL3v4ExtRuleDscp | read-create | current | The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition. The aclL3RuleTos should be specifi… |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.21 | ColumnaclL3v4ExtRuleToS | read-write | current | The ToS value to be checked against the packet. A default value is '-1', which means the rule don't care this condition. The cmAclL3RuleTos should be specified… |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.22 | ColumnaclL3v4ExtRuleIgmpType | read-write | current | The IGMP Type to be checked against the packet.A default value is '-1', which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.26 | ColumnaclL3v4ExtRuleProtocolId | read-write | current | Specifies the protocol id. The aclL3RuleProtocol should be specified as protocol-id. |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.31 | ColumnaclL3v4ExtRuleAction | read-write | current | Specifies the action to be taken on the packet if the filter rule matches. |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.33 | ColumnaclL3v4ExtRulePriority | read-write | current | Enter a priority value if you want to re-write the 802.1p user priority of a packet to the value entered in the Priority field, which meets the criteria specif… |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.34 | ColumnaclL3v4ExtRuleReplacePriority | read-write | current | Enable this option and manually enter the replacement value used to re-write the 802.1p user priority value entered in the Priority field, which meets the crit… |
| 1.3.6.1.4.1.171.10.76.22.1.15.4.1.1.99 | ColumnaclL3v4ExtRuleStatus | read-write | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.76.22.1.15.5 | NodeaclL3v6Rule | |||
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1 | TableaclL3v6RuleTable | not-accessible | current | A table to configure L3 ipv6 filter rules in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1 | RowaclL3v6RuleEntry | not-accessible | current | Each entry in this table is a L3 ipv6 filter rule. Index to the table is L3 ipv6 filter number. |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1.1 | ColumnaclL3v6RuleAccessID | read-only | current | L3 Filter rule ID. |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1.2 | ColumnaclL3v6RuleProfileNo | read-only | current | The Profile ID which this rule join. |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1.3 | ColumnaclL3v6RuleTrafficClass | read-write | current | The Traffic Class value to be checked against the packet. A default value is '-1', which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1.4 | ColumnaclL3v6RuleProtocol | read-write | current | The type of protocol to be checked against the packet. |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1.5 | ColumnaclL3v6RuleProtocolId | read-write | current | Specifies the protocol id. The aclL3v6RuleProtocol should be specified as protocol-id. |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1.6 | ColumnaclL3v6RuleTcpUdpDstPort | read-write | current | The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1.7 | ColumnaclL3v6RuleTcpUdpSrcPort | read-write | current | The TCP / UDP source port. The default value is -1, which means the rule don't care this condition. |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1.8 | ColumnaclL3v6RuleTcpUdpDstPortMask | read-write | current | The TCP / UDP Destination port Mask. |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1.9 | ColumnaclL3v6RuleTcpUdpSrcPortMask | read-write | current | The TCP / UDP Source port Mask. |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1.10 | ColumnaclL3v6RuleICMPv6MessageType | read-write | current | The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action s… |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1.11 | ColumnaclL3v6RuleICMPv6MessageCode | read-write | current | The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action s… |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1.12 | ColumnaclL3v6RuleDstIpv6Addr | read-write | current | Destination IPv6 address to be matched with the packet. |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1.13 | ColumnaclL3v6RuleSrcIpv6Addr | read-write | current | Source IPv6 address to be matched with the packet. |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1.14 | ColumnaclL3v6RuleDstIpv6AddrPrefixLen | read-write | current | The prefix length for Destination IPv6 address. |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1.15 | ColumnaclL3v6RuleSrcIpv6AddrPrefixLen | read-write | current | The prefix length for Source IPv6 address. |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1.90 | ColumnaclL3v6RuleAction | read-write | current | Specifies the action to be taken on the packet if the filter rule matches. |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1.92 | ColumnaclL3v6RulePriority | read-write | current | Enter a priority value if you want to re-write the 802.1p user priority of a packet to the value entered in the Priority field, which meets the criteria specif… |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1.93 | ColumnaclL3v6RuleReplacePriority | read-write | current | Enable this option and manually enter the replacement value used to re-write the 802.1p user priority value entered in the Priority field, which meets the crit… |
| 1.3.6.1.4.1.171.10.76.22.1.15.5.1.1.99 | ColumnaclL3v6RuleStatus | read-write | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.171.10.76.22.1.15.6 | NodeaclPortBindGroup | |||
| 1.3.6.1.4.1.171.10.76.22.1.15.6.1 | TableaclPortGroupTable | not-accessible | current | A table to control the port group binding information of L2 Group, L3v4 Group, and L3v6 Group |
| 1.3.6.1.4.1.171.10.76.22.1.15.6.1.1 | RowaclPortGroupEntry | not-accessible | current | An entry appears in this table for each interface in the system. Index to the table is the interface index of the port. |
| 1.3.6.1.4.1.171.10.76.22.1.15.6.1.1.1 | ColumnaclPortIndex | read-only | current | Interface index of the port for the configuration in this entry applies. |
| 1.3.6.1.4.1.171.10.76.22.1.15.6.1.1.2 | ColumnaclPortL2ProfileNo | read-write | current | The L2 Profile ID which this port bind. zero means not configured. |
| 1.3.6.1.4.1.171.10.76.22.1.15.6.1.1.3 | ColumnaclPortL3v4ProfileNo | read-write | current | The L3v4 Profile ID which this port bind. zero means not configured. |
| 1.3.6.1.4.1.171.10.76.22.1.15.6.1.1.4 | ColumnaclPortL3v6ProfileNo | read-write | current | The L3v6 Profile ID which this port bind. zero means not configured. |
| 1.3.6.1.4.1.171.10.76.22.1.15.8 | NodeaclHWResourceStatus | |||
| 1.3.6.1.4.1.171.10.76.22.1.15.8.1 | TableaclHWResourceStatusTable | not-accessible | current | A table to display HW Resource Status. |
| 1.3.6.1.4.1.171.10.76.22.1.15.8.1.1 | RowaclHWResourceStatusEntry | not-accessible | current | An entry appears in this table for each interface in the system. Index to the table is the HW profile index of the ACL. |
| 1.3.6.1.4.1.171.10.76.22.1.15.8.1.1.1 | ColumnaclHWProfileIndex | read-only | current | HW profile index of the ACL for the configuration in this entry applies. |
| 1.3.6.1.4.1.171.10.76.22.1.15.8.1.1.2 | ColumnaclAccessListNo | read-only | current | The profile name in this HW profile index. |
| 1.3.6.1.4.1.171.10.76.22.1.15.8.1.1.3 | ColumnaclResourceEntryCount | read-only | current | The number of entries in this HW profile index. |
| 1.3.6.1.4.1.171.10.76.22.1.16 | NodecompanySyslog | |||
| 1.3.6.1.4.1.171.10.76.22.1.16.2 | NodesyslogGeneralGroup | |||
| 1.3.6.1.4.1.171.10.76.22.1.16.2.1 | ScalarsyslogState | read-write | current | This object is for enabling or disabling syslog alert features in the system. System Logs record and manage events, as well as report errors and informational … |
| 1.3.6.1.4.1.171.10.76.22.1.16.2.2 | ScalarsyslogTimeStampOption | read-write | current | This object is for enabling or disabling timestamp option. When enabled, the messages (log and email alert messages) will hold the time stamp information. When… |
| 1.3.6.1.4.1.171.10.76.22.1.16.2.3 | ScalarsyslogSrvSeverity | read-write | current | Specifies the log level option to be set for a specific module. |
| 1.3.6.1.4.1.171.10.76.22.1.16.2.4 | ScalarsyslogSrvFacility | read-write | current | The Syslog standard facilities. The facility to be used when sending Syslog messages to this server. |
| 1.3.6.1.4.1.171.10.76.22.1.16.2.5 | TablesyslogSrvTable | not-accessible | current | A table containing entries of priority,server address type, server address, port through which it can send and tranport type. |
| 1.3.6.1.4.1.171.10.76.22.1.16.2.5.1 | RowsyslogSrvEntry | not-accessible | current | A table containing index as priority , server address type and server address. |
| 1.3.6.1.4.1.171.10.76.22.1.16.2.5.1.1 | ColumnsyslogSrvIPType | read-only | current | Specifies the Address type of server.Address type shall be ipv4 or ipv6. |
| 1.3.6.1.4.1.171.10.76.22.1.16.2.5.1.2 | ColumnsyslogSrvIP | read-only | current | Specifies the ServerIP to which the syslog shall be forwarded. |
| 1.3.6.1.4.1.171.10.76.22.1.16.2.5.1.3 | ColumnsyslogSrvPort | read-create | current | Specifies the Port through which it can send the syslog message. By default the the port is 514 |
| 1.3.6.1.4.1.171.10.76.22.1.16.2.5.1.4 | ColumnsyslogInterfaceName | read-create | current | Specifies the interface name when the syslogSrvIP is linklocal address. |
| 1.3.6.1.4.1.171.10.76.22.1.16.2.5.1.5 | ColumnsyslogSrvRowStatus | read-create | current | The Status of the Server Entry. |
| 1.3.6.1.4.1.171.10.76.22.1.17 | NodecompanyLBD | |||
| 1.3.6.1.4.1.171.10.76.22.1.17.1 | ScalarsysLBDStateEnable | read-write | current | Enable/Disable Loopback detection function. The Loopback Detection function is used to detect the loop created by a specific port while Spanning Tree Protocol … |
| 1.3.6.1.4.1.171.10.76.22.1.17.2 | ScalarsysLBDMode | read-write | current | Loopback detection function mode. |
| 1.3.6.1.4.1.171.10.76.22.1.17.3 | ScalarsysLBDInterval | read-write | current | Set a Loop detection Interval between 1 and 32767 seconds. The default is 2 seconds. This time interval to be used at counting time seconds to resend the CTP p… |
| 1.3.6.1.4.1.171.10.76.22.1.17.4 | ScalarsysLBDRecoverTime | read-write | current | This time interval to be used at counting time seconds to recover the disabled port automatically. The Loop Detection Recover Time can be set at 0 seconds, or … |
| 1.3.6.1.4.1.171.10.76.22.1.17.5 | TablesysLBDCtrlTable | not-accessible | current | A table to control Loopback detection features either for the entire switch or for each interface in the switch. |
| 1.3.6.1.4.1.171.10.76.22.1.17.5.1 | RowsysLBDCtrlEntry | not-accessible | current | An entry appears in this table for each interface in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.17.5.1.1 | ColumnsysLBDCtrlIndex | read-only | current | The interface index of the port for which the configuration in this entry applies. |
| 1.3.6.1.4.1.171.10.76.22.1.17.5.1.2 | ColumnsysLBDPortStatus | read-write | current | Provides control to per port enable or disable the loopback detection function. Default is disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.17.5.1.3 | ColumnsysLBDPortLoopStatus | read-only | current | The loop status for this port. |
| 1.3.6.1.4.1.171.10.76.22.1.17.6 | TablesysLBDVlanLoopTable | not-accessible | current | A table to display Loopback detection features by vlan mode . |
| 1.3.6.1.4.1.171.10.76.22.1.17.6.1 | RowsysLBDVlanLoopEntry | not-accessible | current | An entry appears in this table for each interface in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.17.6.1.1 | ColumnsysLBDVlanLoopIndex | read-only | current | Display port lists loop status by vlan. |
| 1.3.6.1.4.1.171.10.76.22.1.17.6.1.2 | ColumnsysLBDVlanLoopPorts | read-only | current | Display port lists loop status by vlan. |
| 1.3.6.1.4.1.171.10.76.22.1.17.7 | ScalarswLoopDetectEnabledVlanList | read-write | current | This object indicates the VLANs that enabled LBD. Note: For the LBD enabled VLAN specification, the value should be separated by ',' or '-'. Such as: 1,4,7 or … |
| 1.3.6.1.4.1.171.10.76.22.1.18 | NodecompanyMirror | |||
| 1.3.6.1.4.1.171.10.76.22.1.18.1 | ScalarsysMirrorStatus | read-write | current | Enable/Disable Port Mirroring function. Default is disabled. Port Mirroring is a method of monitoring network traffic that forwards a copy of each incoming and… |
| 1.3.6.1.4.1.171.10.76.22.1.18.2 | ScalarsysMirrorTargetPort | read-write | current | Specifies the port to which the mirrored traffic in the system is to be copied. |
| 1.3.6.1.4.1.171.10.76.22.1.18.3 | ScalarsysMirrorCtrlIngressMirroring | read-write | current | Provides control to enable or disable mirroring of ingress traffic over this interface to the mirrored-to port. |
| 1.3.6.1.4.1.171.10.76.22.1.18.4 | ScalarsysMirrorCtrlEgressMirroring | read-write | current | Provides control to enable or disable mirroring of egress traffic over this interface to the mirrored-to port. |
| 1.3.6.1.4.1.171.10.76.22.1.20 | NodecompanySNTPSetting | |||
| 1.3.6.1.4.1.171.10.76.22.1.20.17 | NodesysSNTPServerTable | |||
| 1.3.6.1.4.1.171.10.76.22.1.20.17.1 | ScalarsysSNTPTimeSeconds | read-write | current | This object is for setting the system time in seconds from Epoch (00:00:00 UTC, January 1, 2009). Notice : input value must larger than 1230768000 (00:00:00 UT… |
| 1.3.6.1.4.1.171.10.76.22.1.20.17.2 | ScalarsysSNTPFirstServer | read-write | current | SNTP First Server's IPv6 Address |
| 1.3.6.1.4.1.171.10.76.22.1.20.17.3 | ScalarsysSNTPFirstType | read-write | current | SNTP First Server's IPv6 Address type. |
| 1.3.6.1.4.1.171.10.76.22.1.20.17.4 | ScalarsysSNTPFirstInterfaceName | read-write | current | Specifies the interface name when the sysSNTPFirstServer is linklocal address. |
| 1.3.6.1.4.1.171.10.76.22.1.20.17.5 | ScalarsysSNTPSecondServer | read-write | current | SNTP Second Server's IPv6 Address |
| 1.3.6.1.4.1.171.10.76.22.1.20.17.6 | ScalarsysSNTPSecondType | read-write | current | SNTP First Server's IPv6 Address type. |
| 1.3.6.1.4.1.171.10.76.22.1.20.17.7 | ScalarsysSNTPSecondInterfaceName | read-write | current | Specifies the interface name when the sysSNTPSecondServer is linklocal address. |
| 1.3.6.1.4.1.171.10.76.22.1.20.17.8 | ScalarsysSNTPPollInterval | read-write | current | SNTP Poll Interval In Seconds (30-99999) |
| 1.3.6.1.4.1.171.10.76.22.1.20.17.9 | ScalarsysSNTPState | read-write | current | Enable/Disable SNTP function in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.20.17.10 | ScalarsysSNTPDSTOffset | read-write | current | This object is for Daylight Saving Time Offset In (30/60/90/120) Minutes. |
| 1.3.6.1.4.1.171.10.76.22.1.20.17.11 | ScalarsysSNTPGMTMinutes | read-write | current | Specifies the Time Zone Offset from GMT in +/- Minutes. (+780 ~ -720) |
| 1.3.6.1.4.1.171.10.76.22.1.20.17.12 | ScalarsysSNTPDSTStartMon | read-write | current | The start month of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.76.22.1.20.17.13 | ScalarsysSNTPDSTStartDay | read-write | current | The start day of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.76.22.1.20.17.14 | ScalarsysSNTPDSTStartHour | read-write | current | The start hour of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.76.22.1.20.17.15 | ScalarsysSNTPDSTStartMin | read-write | current | The start minute of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.76.22.1.20.17.16 | ScalarsysSNTPDSTEndMon | read-write | current | The end month of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.76.22.1.20.17.17 | ScalarsysSNTPDSTEndDay | read-write | current | The end day of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.76.22.1.20.17.18 | ScalarsysSNTPDSTEndHour | read-write | current | The end hour of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.76.22.1.20.17.19 | ScalarsysSNTPDSTEndMin | read-write | current | The end minute of Daylight Saving Time. |
| 1.3.6.1.4.1.171.10.76.22.1.20.17.20 | ScalarsysSNTPDSTState | read-write | current | This object is for Annual(1) or Disabled(2) DST state in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.21 | NodecompanyVoiceVlan | |||
| 1.3.6.1.4.1.171.10.76.22.1.21.1 | NodevoicevlanSystem | |||
| 1.3.6.1.4.1.171.10.76.22.1.21.1.2 | ScalarvoiceVlanMode | read-write | current | Voice VLAN is a feature that allows you to automatically place the voice traffic from IP phone to an assigned VLAN to enhance the VoIP service. This object is … |
| 1.3.6.1.4.1.171.10.76.22.1.21.1.3 | ScalarvoiceVlanId | read-write | current | The ID of VLAN that you want the voice traffic to be in. It must be a exist vlan id. |
| 1.3.6.1.4.1.171.10.76.22.1.21.1.4 | ScalarvoiceVlanTimeout | read-write | current | A period of time in hour to remove a port from voice VLAN if the port is an automatic VLAN member. The Timeout range is 1~120 hours. Default aging time is 1 ho… |
| 1.3.6.1.4.1.171.10.76.22.1.21.1.5 | ScalarvoiceVlanPriority | read-write | current | The 802.1p priority levels of the traffic in the Voice VLAN. |
| 1.3.6.1.4.1.171.10.76.22.1.21.1.6 | TablevoicevlanPortControlTable | not-accessible | current | A table that contains Voice Vlan Port Control configuration information. |
| 1.3.6.1.4.1.171.10.76.22.1.21.1.6.1 | RowvoicevlanPortControlEntry | not-accessible | current | A list of Voice Vlan Control configuration parameters for each Port on this device. |
| 1.3.6.1.4.1.171.10.76.22.1.21.1.6.1.1 | ColumnvoicevlanPortControlIndex | read-only | current | The voice vlan port index. |
| 1.3.6.1.4.1.171.10.76.22.1.21.1.6.1.2 | ColumnvoicevlanPortAutoDetection | read-write | current | This object is for enabling or disabling Voice Vlan Auto Detection in the port. If the auto detection is enable, switch will add this port to the voice VLAN au… |
| 1.3.6.1.4.1.171.10.76.22.1.21.1.6.1.3 | ColumnvoicevlanPortManuTagMode | read-write | current | User assign per port tag/untag mode. |
| 1.3.6.1.4.1.171.10.76.22.1.21.1.6.1.4 | ColumnvoicevlanPortCurrentTagMode | read-only | current | Per port current tag/untag mode. |
| 1.3.6.1.4.1.171.10.76.22.1.21.1.6.1.5 | ColumnvoicevlanPortState | read-only | current | This object indicates Voice vlan state to this Port. manual - this port is a static member of voice vlan. dynamic - this port is a dynamic member of voice vlan… |
| 1.3.6.1.4.1.171.10.76.22.1.21.2 | NodevoicevlanOUI | |||
| 1.3.6.1.4.1.171.10.76.22.1.21.2.1 | TablevoicevlanOUITable | not-accessible | current | A voice vlan OUI entry containing the description and mac. |
| 1.3.6.1.4.1.171.10.76.22.1.21.2.1.1 | RowvoicevlanOUIEntry | not-accessible | current | A voice vlan OUI entry containing the description and mac. |
| 1.3.6.1.4.1.171.10.76.22.1.21.2.1.1.1 | ColumnvoicevlanOUITelephonyOUI | read-only | current | An Organizationally Unique Identifier (OUI) is a 24-bit number that is purchased from the IEEE Registration Authority. This identifier uniquely identifies a ve… |
| 1.3.6.1.4.1.171.10.76.22.1.21.2.1.1.2 | ColumnvoicevlanOUIDescription | read-write | current | The Description for the OUI. |
| 1.3.6.1.4.1.171.10.76.22.1.21.2.1.1.3 | ColumnvoicevlanOUIMask | read-only | current | Voice vlan OUI Mask. Always be FF:FF:FF:00:00:00. |
| 1.3.6.1.4.1.171.10.76.22.1.21.2.1.1.4 | ColumnvoicevlanOUIStatus | read-write | current | This object indicates the status of this entry. To create a new entry, you must set the voicevlanOUIStatus to be CreateAndGo, then this entry will turn to be A… |
| 1.3.6.1.4.1.171.10.76.22.1.21.3 | NodevoicevlanDevice | |||
| 1.3.6.1.4.1.171.10.76.22.1.21.3.1 | TablevoicevlanDeviceTable | not-accessible | current | A voice vlan Device entry containing the description and mac. |
| 1.3.6.1.4.1.171.10.76.22.1.21.3.1.1 | RowvoicevlanDeviceEntry | not-accessible | current | A voice vlan Device entry containing the description and mac. |
| 1.3.6.1.4.1.171.10.76.22.1.21.3.1.1.1 | ColumnvoicevlanDeviceIndexMac | read-only | current | An Mac Address is a 24-bit number that is purchased from the IEEE Registration Authority. This identifier uniquely identifies a vendor, manufacturer, or other … |
| 1.3.6.1.4.1.171.10.76.22.1.21.3.1.1.2 | ColumnvoicevlanDevicePort | read-only | current | The port is learning by voice device. |
| 1.3.6.1.4.1.171.10.76.22.1.21.3.1.1.3 | ColumnvoicevlanDevicePriority | read-only | current | The priority value for voice device. |
| 1.3.6.1.4.1.171.10.76.22.1.21.3.1.1.4 | ColumnvoicevlanDeviceTagType | read-only | current | The tag type for voice device. |
| 1.3.6.1.4.1.171.10.76.22.1.21.3.1.1.5 | ColumnvoicevlanDeviceStatus | read-write | current | This object indicates the status of this entry. You can delete this object. |
| 1.3.6.1.4.1.171.10.76.22.1.23 | NodecompanyAuthGroup | |||
| 1.3.6.1.4.1.171.10.76.22.1.23.1 | NodeswAuthenCtrl | |||
| 1.3.6.1.4.1.171.10.76.22.1.23.1.1 | ScalarswAuthStatus | read-write | current | Enable/Disable Static 802.1x. |
| 1.3.6.1.4.1.171.10.76.22.1.23.1.3 | ScalarauthProtocol | read-write | current | The authentication method used to authenticate users. |
| 1.3.6.1.4.1.171.10.76.22.1.23.1.4 | ScalarswAuthCtrlPktFwdMode | read-write | current | Enable/Disable 802.1x packet forward while 802.1x module is disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.23.2 | NodeswAuthPortAccessCtrl | |||
| 1.3.6.1.4.1.171.10.76.22.1.23.2.1 | TableswAuthPortAccessControlTable | not-accessible | current | A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may auth… |
| 1.3.6.1.4.1.171.10.76.22.1.23.2.1.1 | RowswAuthPortAccessControlEntry | not-accessible | current | The configuration information for an Authenticator Port. |
| 1.3.6.1.4.1.171.10.76.22.1.23.2.1.1.1 | ColumnswAuthAuthConfigPortNumber | read-only | current | A unique value for each port that correlates to port index. Its value ranges between 1 and the value of port number. |
| 1.3.6.1.4.1.171.10.76.22.1.23.2.1.1.2 | ColumnswAuthAuthQuietPeriod | read-write | current | The value, in seconds, of the quietPeriod constant currently in use by the Authenticator PAE state machine. |
| 1.3.6.1.4.1.171.10.76.22.1.23.2.1.1.3 | ColumnswAuthAuthSuppTimeout | read-write | current | The value, in seconds, of the suppTimeout constant currently in use by the Backend Authentication state machine. |
| 1.3.6.1.4.1.171.10.76.22.1.23.2.1.1.4 | ColumnswAuthAuthServerTimeout | read-write | current | The value, in seconds, of the serverTimeout constant currently in use by the Backend Authentication state machine. |
| 1.3.6.1.4.1.171.10.76.22.1.23.2.1.1.5 | ColumnswAuthAuthMaxReq | read-write | current | The value of the maxReq constant currently in use by the Backend Authentication state machine. |
| 1.3.6.1.4.1.171.10.76.22.1.23.2.1.1.6 | ColumnswAuthAuthTxPeriod | read-write | current | The value, in seconds, of the txPeriod constant currently in use by the Authenticator PAE state machine. |
| 1.3.6.1.4.1.171.10.76.22.1.23.2.1.1.7 | ColumnswAuthAuthReAuthPeriod | read-write | current | The value, in seconds, of the reAuthPeriod constant currently in use by the Reauthentication Timer state machine. |
| 1.3.6.1.4.1.171.10.76.22.1.23.2.1.1.8 | ColumnswAuthAuthReAuthentication | read-write | current | The enable/disable control used by the Reauthentication Timer state machine (8.5.5.1). |
| 1.3.6.1.4.1.171.10.76.22.1.23.2.1.1.9 | ColumnswAuthAuthConfigPortControl | read-write | current | The current value of the controlled Port control parameter for the Port. |
| 1.3.6.1.4.1.171.10.76.22.1.23.2.1.1.10 | ColumnswAuthAuthCapability | read-write | current | The current value of the controlled Port control parameter for the Port. |
| 1.3.6.1.4.1.171.10.76.22.1.23.2.1.1.11 | ColumnswAuthAuthDirection | read-write | current | The current value of the controlled Port control parameter for the Port. |
| 1.3.6.1.4.1.171.10.76.22.1.23.3 | NodeswAuthUser | |||
| 1.3.6.1.4.1.171.10.76.22.1.23.3.1 | TableswAuthUserTable | not-accessible | current | A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may auth… |
| 1.3.6.1.4.1.171.10.76.22.1.23.3.1.1 | RowswAuthUserEntry | not-accessible | current | The configuration information for an Authenticator Port. |
| 1.3.6.1.4.1.171.10.76.22.1.23.3.1.1.1 | ColumnswAuthUserName | read-only | current | The unique index value of a row in this table. This object is used to set 802.1X Local user name, The following characters are allowed to input: semicolon, que… |
| 1.3.6.1.4.1.171.10.76.22.1.23.3.1.1.2 | ColumnswAuthUserPassword | read-write | current | This object is used to set 802.1X Local user Password, The following characters are allowed to input: semicolon, question mark, space, and double quotation mar… |
| 1.3.6.1.4.1.171.10.76.22.1.23.3.1.1.3 | ColumnswAuthUserStatus | read-create | current | The status of this conceptual row in the swAuthUserTable. An entry in this table is not qualified for activation until instances of all corresponding columns h… |
| 1.3.6.1.4.1.171.10.76.22.1.23.4 | NodeswAuthRadiusServer | |||
| 1.3.6.1.4.1.171.10.76.22.1.23.4.2 | TableswAuthRadiusServerTable | not-accessible | current | A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may auth… |
| 1.3.6.1.4.1.171.10.76.22.1.23.4.2.1 | RowswAuthRadiusServerEntry | not-accessible | current | The configuration information for an Authenticator Port. |
| 1.3.6.1.4.1.171.10.76.22.1.23.4.2.1.1 | ColumnswAuthRadiusServerIndex | read-only | current | A unique value for Authentication RADIUS Server index. Its value ranges between 1 and 3. |
| 1.3.6.1.4.1.171.10.76.22.1.23.4.2.1.2 | ColumnswAuthRadiusIPType | read-write | current | The IP address of the RADIUS server IP type referred to in this table entry. |
| 1.3.6.1.4.1.171.10.76.22.1.23.4.2.1.3 | ColumnswAuthRadiusServerAddress | read-write | current | The IP address of the RADIUS server referred to in this table entry. |
| 1.3.6.1.4.1.171.10.76.22.1.23.4.2.1.4 | ColumnswAuthRadiusServerInterfaceName | read-create | current | Specifies the interface name when the swAuthRadiusServerAddress is linklocal address. |
| 1.3.6.1.4.1.171.10.76.22.1.23.4.2.1.5 | ColumnswAuthRadiusServerAuthenticationPort | read-write | current | The value is for setting UDP Port. |
| 1.3.6.1.4.1.171.10.76.22.1.23.4.2.1.6 | ColumnswAuthRadiusServerAccountingPort | read-write | current | The value is for setting UDP Port. |
| 1.3.6.1.4.1.171.10.76.22.1.23.4.2.1.7 | ColumnswAuthRadiusServerTimeout | read-write | current | The value is for setting UDP Port. |
| 1.3.6.1.4.1.171.10.76.22.1.23.4.2.1.8 | ColumnswAuthRadiusServerRetransmit | read-write | current | The value is for setting UDP Port. |
| 1.3.6.1.4.1.171.10.76.22.1.23.4.2.1.9 | ColumnswAuthRadiusServerKey | read-write | current | This object is used to set 802.1X Radius Server Key, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark. |
| 1.3.6.1.4.1.171.10.76.22.1.23.4.2.1.10 | ColumnswAuthRadiusServerStatus | read-create | current | The status of this conceptual row in the swAuthRadiusServerTable. An entry in this table is not qualified for activation until instances of all corresponding c… |
| 1.3.6.1.4.1.171.10.76.22.1.24 | NodecompanyLLDPSetting | |||
| 1.3.6.1.4.1.171.10.76.22.1.24.1 | ScalardlinklldpState | read-write | current | This object is used for enabling or disabling LLDP in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.24.2 | ScalardlinklldpMsgHoldMultiplier | read-write | current | The time-to-live value expressed as a multiple of the lldpMessageTxInterval object.The actual time-to-live value used in LLDP frames, transmitted on behalf of … |
| 1.3.6.1.4.1.171.10.76.22.1.24.3 | ScalardlinklldpMsgTxInterval | read-write | current | This object is used for LLDP packet update frequency. The timer in units of seconds. |
| 1.3.6.1.4.1.171.10.76.22.1.24.4 | ScalardlinklldpReinitDelay | read-write | current | This object is used for LLDP Reinitialization Delay. The timer in units of seconds. |
| 1.3.6.1.4.1.171.10.76.22.1.24.5 | ScalardlinklldpTxDelay | read-write | current | The lldpTxDelay indicates the delay (in units of seconds) between successive LLDP frame transmissions initiated by value/status changes in the LLDP local syste… |
| 1.3.6.1.4.1.171.10.76.22.1.24.7 | TabledlinklldpConfigManAddrTable | not-accessible | current | The table that controls selection of LLDP management address TLV instances to be transmitted on individual ports. |
| 1.3.6.1.4.1.171.10.76.22.1.24.7.1 | RowdlinklldpConfigManAddrEntry | not-accessible | current | LLDP configuration information that specifies the set of ports (represented as a PortList) on which the local system management address instance will be transm… |
| 1.3.6.1.4.1.171.10.76.22.1.24.7.1.1 | ColumndlinklldpLocManAddrSubtype | read-only | current | The type of management address identifier encoding used in the associated 'lldpLocManagmentAddr' object. |
| 1.3.6.1.4.1.171.10.76.22.1.24.7.1.2 | ColumndlinklldpLocManAddr | read-only | current | The string value used to identify the management address component associated with the local system. The purpose of this address is to contact the management e… |
| 1.3.6.1.4.1.171.10.76.22.1.24.7.1.3 | ColumndlinklldpConfigManAddrPortsTxEnable | read-write | current | A set of ports that are identified by a PortList, in which each port is represented as a bit. The corresponding local system management address instance will b… |
| 1.3.6.1.4.1.171.10.76.22.1.25 | NodecompanySNMPV3 | |||
| 1.3.6.1.4.1.171.10.76.22.1.25.1 | ScalarsnmpGlobalState | read-write | current | This object is for enabling or disabling SNMP Community function. |
| 1.3.6.1.4.1.171.10.76.22.1.25.2 | NodesnmpV3User | |||
| 1.3.6.1.4.1.171.10.76.22.1.25.2.1 | TablesnmpV3UserTable | not-accessible | current | |
| 1.3.6.1.4.1.171.10.76.22.1.25.2.1.1 | RowsnmpV3UserEntry | not-accessible | current | |
| 1.3.6.1.4.1.171.10.76.22.1.25.2.1.1.1 | ColumnsnmpV3UserName | read-only | current | A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID. |
| 1.3.6.1.4.1.171.10.76.22.1.25.2.1.1.2 | ColumnsnmpV3UserVersion | read-only | current | A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID. |
| 1.3.6.1.4.1.171.10.76.22.1.25.2.1.1.3 | ColumnsnmpV3UserGroupName | read-create | current | The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAcces… |
| 1.3.6.1.4.1.171.10.76.22.1.25.2.1.1.4 | ColumnsnmpV3UserAuthProtocol | read-create | current | An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be authenticated, and if so, the type … |
| 1.3.6.1.4.1.171.10.76.22.1.25.2.1.1.5 | ColumnsnmpV3UserAuthProtocolPassword | read-create | current | |
| 1.3.6.1.4.1.171.10.76.22.1.25.2.1.1.6 | ColumnsnmpV3UserPrivProtocol | read-create | current | An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be protected from disclosure, and if s… |
| 1.3.6.1.4.1.171.10.76.22.1.25.2.1.1.7 | ColumnsnmpV3UserPrivProtocolPassword | read-create | current | |
| 1.3.6.1.4.1.171.10.76.22.1.25.2.1.1.8 | ColumnsnmpV3UserStatus | read-create | current | The status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the us… |
| 1.3.6.1.4.1.171.10.76.22.1.25.3 | NodesnmpV3Group | |||
| 1.3.6.1.4.1.171.10.76.22.1.25.3.1 | TablesnmpV3GroupTable | not-accessible | current | |
| 1.3.6.1.4.1.171.10.76.22.1.25.3.1.1 | RowsnmpV3GroupEntry | not-accessible | current | |
| 1.3.6.1.4.1.171.10.76.22.1.25.3.1.1.1 | ColumnsnmpV3GroupName | read-only | current | The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAcces… |
| 1.3.6.1.4.1.171.10.76.22.1.25.3.1.1.2 | ColumnsnmpV3GroupSecurityModel | read-only | current | In order to gain the access rights allowed by this conceptual row, this securityModel must be in use. |
| 1.3.6.1.4.1.171.10.76.22.1.25.3.1.1.3 | ColumnsnmpV3GroupSecurityLevel | read-only | current | The minimum level of security required in order to gain the access rights allowed by this conceptual row. A securityLevel of noAuthNoPriv is less than authNoPr… |
| 1.3.6.1.4.1.171.10.76.22.1.25.3.1.1.4 | ColumnsnmpV3GroupReadViewName | read-create | current | The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes read access. The identified MIB vie… |
| 1.3.6.1.4.1.171.10.76.22.1.25.3.1.1.5 | ColumnsnmpV3GroupWriteViewName | read-create | current | The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes write access. The identified MIB vi… |
| 1.3.6.1.4.1.171.10.76.22.1.25.3.1.1.6 | ColumnsnmpV3GroupNotifyViewName | read-create | current | The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes access for notifications. The ident… |
| 1.3.6.1.4.1.171.10.76.22.1.25.3.1.1.7 | ColumnsnmpV3GroupStatus | read-create | current | The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row … |
| 1.3.6.1.4.1.171.10.76.22.1.25.4 | NodesnmpV3ViewTree | |||
| 1.3.6.1.4.1.171.10.76.22.1.25.4.1 | TablesnmpV3ViewTreeTable | not-accessible | current | |
| 1.3.6.1.4.1.171.10.76.22.1.25.4.1.1 | RowsnmpV3ViewTreeEntry | not-accessible | current | |
| 1.3.6.1.4.1.171.10.76.22.1.25.4.1.1.1 | ColumnsnmpV3viewTreeName | read-only | current | The human readable name for a family of view subtrees. |
| 1.3.6.1.4.1.171.10.76.22.1.25.4.1.1.2 | ColumnsnmpV3viewTreeSubtree | read-only | current | The MIB subtree which when combined with the corresponding instance of vacmViewTreeFamilyMask defines a family of view subtrees. |
| 1.3.6.1.4.1.171.10.76.22.1.25.4.1.1.3 | ColumnsnmpV3viewTreeMask | read-create | current | The bit mask which, in combination with the corresponding instance of vacmViewTreeFamilySubtree, defines a family of view subtrees. Each bit of this bit mask c… |
| 1.3.6.1.4.1.171.10.76.22.1.25.4.1.1.4 | ColumnsnmpV3viewTreeType | read-create | current | Indicates whether the corresponding instances of vacmViewTreeFamilySubtree and vacmViewTreeFamilyMask define a family of view subtrees which is included in or … |
| 1.3.6.1.4.1.171.10.76.22.1.25.4.1.1.5 | ColumnsnmpV3viewTreeStatus | read-create | current | The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row … |
| 1.3.6.1.4.1.171.10.76.22.1.25.5 | NodesnmpV3Community | |||
| 1.3.6.1.4.1.171.10.76.22.1.25.5.1 | TablesnmpV3CommunityTable | not-accessible | current | |
| 1.3.6.1.4.1.171.10.76.22.1.25.5.1.1 | RowsnmpV3CommunityEntry | not-accessible | current | |
| 1.3.6.1.4.1.171.10.76.22.1.25.5.1.1.1 | ColumnsnmpV3CommunityName | read-only | current | The unique index value of a row in this table. |
| 1.3.6.1.4.1.171.10.76.22.1.25.5.1.1.2 | ColumnsnmpV3CommunityPolicy | read-create | current | A human readable string representing the corresponding value of snmpCommunityName in a Security Model independent format. |
| 1.3.6.1.4.1.171.10.76.22.1.25.5.1.1.3 | ColumnsnmpV3CommunityStatus | read-create | current | The status of this conceptual row in the snmpCommunityTable. An entry in this table is not qualified for activation until instances of all corresponding column… |
| 1.3.6.1.4.1.171.10.76.22.1.25.6 | NodesnmpV3Host | |||
| 1.3.6.1.4.1.171.10.76.22.1.25.6.2 | TablesnmpV3HostTable | not-accessible | current | |
| 1.3.6.1.4.1.171.10.76.22.1.25.6.2.1 | RowsnmpV3HostEntry | not-accessible | current | |
| 1.3.6.1.4.1.171.10.76.22.1.25.6.2.1.1 | ColumnsnmpV3HostAddress | read-only | current | This object contains a transport address. The format of this address depends on the value of the snmpTargetAddrTDomain object. And this object is unique identi… |
| 1.3.6.1.4.1.171.10.76.22.1.25.6.2.1.2 | ColumnsnmpV3IPType | read-only | current | Type of IP interface. |
| 1.3.6.1.4.1.171.10.76.22.1.25.6.2.1.3 | ColumnsnmpV3HostCommunityName | read-create | current | The locally arbitrary. |
| 1.3.6.1.4.1.171.10.76.22.1.25.6.2.1.4 | ColumnsnmpV3HostVersion | read-create | current | The Level of Security to be used when generating SNMP messages using this entry. |
| 1.3.6.1.4.1.171.10.76.22.1.25.6.2.1.5 | ColumnsnmpV3HostInterfaceName | read-create | current | Specifies the interface name when the syslogSrvIP is linklocal address. |
| 1.3.6.1.4.1.171.10.76.22.1.25.6.2.1.6 | ColumnsnmpV3HostStatus | read-create | current | |
| 1.3.6.1.4.1.171.10.76.22.1.25.7 | ScalarsnmpV3EngineID | read-write | current | An SNMP engine's administratively-unique identifier. In a simple agent, this value is always that agent's own snmpEngineID value. The value can also take the v… |
| 1.3.6.1.4.1.171.10.76.22.1.25.8 | NodesnmpV3Trap | |||
| 1.3.6.1.4.1.171.10.76.22.1.25.8.1 | ScalarsnmpV3TrapSNMPAuthentication | read-write | current | This object is for enabling or disabling SNMP login fail event trap in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.25.8.2 | ScalarsnmpV3TrapBootup | read-write | current | This object is for enabling or disabling devie Bootup event trap in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.25.8.3 | ScalarsnmpV3TrapPortLinkUpDown | read-write | current | This object is for enabling or disabling Port link up / link down event trap in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.25.8.4 | ScalarsnmpV3TrapRSTPStateChange | read-write | current | This object is for enabling or disabling RSTP topology change event trap in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.25.8.5 | ScalarsnmpV3TrapFirmUpgrade | read-write | current | This object is for enabling or disabling Firmware upgrade suess or fail event trap in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.25.8.11 | ScalarsnmpV3TrapLBD | read-write | current | |
| 1.3.6.1.4.1.171.10.76.22.1.26 | NodecompanyAutoSurveillanceVlan | |||
| 1.3.6.1.4.1.171.10.76.22.1.26.1 | NodeautoSurveillanceVlanSystem | |||
| 1.3.6.1.4.1.171.10.76.22.1.26.1.1 | ScalarautoSurveillanceVlanMode | read-write | current | This object is for enabling or disabling Auto Surveillance Vlan function in the system. If the Vlan mode is in Asymmetric VLAN mode, Auto Surveillance VLAN can… |
| 1.3.6.1.4.1.171.10.76.22.1.26.1.2 | ScalarautoSurveillanceVlanId | read-write | current | The ID of VLAN that you want the surveillance traffic to be in. It must be a exist vlan id. |
| 1.3.6.1.4.1.171.10.76.22.1.26.1.3 | ScalarautoSurveillanceVlanPriority | read-write | current | The 802.1p priority levels of the traffic in the Auto Surveillance VLAN. |
| 1.3.6.1.4.1.171.10.76.22.1.26.1.4 | ScalarautoSurveillanceVlanTaggedUplinkDownlinkPort | read-write | current | Auto Surveillance vlan uplink ports can't auto learning OUI. |
| 1.3.6.1.4.1.171.10.76.22.1.26.2 | NodeautoSurveillanceVlanOUI | |||
| 1.3.6.1.4.1.171.10.76.22.1.26.2.1 | TableautoSurveillanceVlanOUITable | not-accessible | current | A Auto Surveillance vlan OUI entry containing the description and mac. |
| 1.3.6.1.4.1.171.10.76.22.1.26.2.1.1 | RowautoSurveillanceVlanOUIEntry | not-accessible | current | A Auto Surveillance vlan OUI entry containing the description and mac. |
| 1.3.6.1.4.1.171.10.76.22.1.26.2.1.1.1 | ColumnautoSurveillanceVlanOUISurveillanceOUI | read-only | current | An Organizationally Unique Identifier (OUI) is a 24-bit number that is purchased from the IEEE Registration Authority. This identifier uniquely identifies a ve… |
| 1.3.6.1.4.1.171.10.76.22.1.26.2.1.1.2 | ColumnautoSurveillanceVlanOUIDescription | read-write | current | The Description for the OUI. |
| 1.3.6.1.4.1.171.10.76.22.1.26.2.1.1.3 | ColumnautoSurveillanceVlanOUIMask | read-write | current | Auto Surveillance vlan OUI Mask. The default OUI Mask is FF:FF:FF:F0:00:00. And default OUI Mask is read-only. In user define OUI's Mask is FF:FF:FF:00:00:00, … |
| 1.3.6.1.4.1.171.10.76.22.1.26.2.1.1.4 | ColumnautoSurveillanceVlanOUIComponentType | read-write | current | This object indicates the Component Type of this entry. To create a new entry, you must set the autoSurveillanceVlanOUIComponentType to be CreateAndGo, then th… |
| 1.3.6.1.4.1.171.10.76.22.1.26.2.1.1.5 | ColumnautoSurveillanceVlanOUIStatus | read-write | current | This object indicates the status of this entry. To create a new entry, you must set the autoSurveillanceVlanOUIStatus to be CreateAndGo, then this entry will t… |
| 1.3.6.1.4.1.171.10.76.22.1.27 | NodecompanyTraps | |||
| 1.3.6.1.4.1.171.10.76.22.1.27.0 | Nodetraps | |||
| 1.3.6.1.4.1.171.10.76.22.1.27.0.4 | NotificationtopologyChange | current | AST_TOPOLOGY_CHG_TRAP_VAL. | |
| 1.3.6.1.4.1.171.10.76.22.1.27.0.8 | NotificationfirmwareUpgradeSuccess | current | SNMP_FIRMUPGRADE_SUCC. | |
| 1.3.6.1.4.1.171.10.76.22.1.27.0.9 | NotificationfirmwareUpgradeFailure | current | SNMP_FIRMUPGRADE_FAIL. | |
| 1.3.6.1.4.1.171.10.76.22.1.27.0.10 | NotificationfirmwareIllegalFile | current | SNMP_FIRMUPGRADE_FAIL2. | |
| 1.3.6.1.4.1.171.10.76.22.1.27.0.11 | NotificationfirmwareTransferError | current | SNMP_FIRMUPGRADE_FAIL1. | |
| 1.3.6.1.4.1.171.10.76.22.1.27.0.12 | NotificationfirmwareChecksumError | current | SNMP_FIRMUPGRADE_FAIL3. | |
| 1.3.6.1.4.1.171.10.76.22.1.31 | NodecompanyGreenSetting | |||
| 1.3.6.1.4.1.171.10.76.22.1.31.1 | NodedlinkGreenLEDShutoff | |||
| 1.3.6.1.4.1.171.10.76.22.1.31.1.1 | ScalardlinkGreenLEDShutoffPortList | read-write | current | Provides control to disable LED port. |
| 1.3.6.1.4.1.171.10.76.22.1.31.1.2 | ScalardlinkGreenLEDShutoffState | read-write | current | Enable/Disable Green disable LED function. Default is disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.31.1.3 | ScalardlinkGreenLEDShutoffTimeProfile1 | read-write | current | The time profile name associated with the Schedule entry (e.g., `abc, bbb'). |
| 1.3.6.1.4.1.171.10.76.22.1.31.1.4 | ScalardlinkGreenLEDShutoffTimeProfile2 | read-write | current | The time profile name associated with the Schedule entry (e.g., `abc, bbb'). |
| 1.3.6.1.4.1.171.10.76.22.1.31.2 | NodedlinkGreenPortShutoff | |||
| 1.3.6.1.4.1.171.10.76.22.1.31.2.1 | ScalardlinkGreenPortShutoffPortList | read-write | current | Provides control to disable LED port. |
| 1.3.6.1.4.1.171.10.76.22.1.31.2.2 | ScalardlinkGreenPortShutoffState | read-write | current | Enable/Disable Green disable LED function. Default is disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.31.2.3 | ScalardlinkGreenPortShutoffTimeProfile1 | read-write | current | The time profile name associated with the Schedule entry (e.g., `abc, bbb'). |
| 1.3.6.1.4.1.171.10.76.22.1.31.2.4 | ScalardlinkGreenPortShutoffTimeProfile2 | read-write | current | The time profile name associated with the Schedule entry (e.g., `abc, bbb'). |
| 1.3.6.1.4.1.171.10.76.22.1.31.4 | NodedlinkGreenSystemHibernation | |||
| 1.3.6.1.4.1.171.10.76.22.1.31.4.1 | ScalardlinkGreenSystemHibernationState | read-write | current | Enable/Disable Green disable LED function. Default is disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.31.4.2 | ScalardlinkGreenSystemHibernationTimeProfile1 | read-write | current | The time profile name associated with the Schedule entry (e.g., `abc, bbb'). |
| 1.3.6.1.4.1.171.10.76.22.1.31.4.3 | ScalardlinkGreenSystemHibernationTimeProfile2 | read-write | current | The time profile name associated with the Schedule entry (e.g., `abc, bbb'). |
| 1.3.6.1.4.1.171.10.76.22.1.31.6 | ScalardlinkPowerSavingGlobalSetting | read-write | current | Enable/Disable Power Saving global setting. Default is disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.32 | NodecompanyTimeRangeMgmt | |||
| 1.3.6.1.4.1.171.10.76.22.1.32.1 | TableswTimeRangeSettingTable | not-accessible | current | A table to configure time Range in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1 | RowswTimeRangeSettingEntry | not-accessible | current | A schedule entry to configure time Range in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.1 | ColumnswTimeRangeIndex | read-only | current | The Time Range identifier. The maximum number of Schedule entry is the number of ports supported PoE function. The value must be between 1 and 52. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.2 | ColumnswTimeRangeName | read-write | current | The Schedule name associated with the Schedule entry (e.g., `abc, bbb'). |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.3 | ColumnswTimeRangeDate | read-write | current | Enable/Disable date range checking while executing time base PoE. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.4 | ColumnswTimeRangeStartYear | read-write | current | Start year of the Schedule entry. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.5 | ColumnswTimeRangeStartMonth | read-write | current | Start month of the Schedule entry. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.6 | ColumnswTimeRangeStartDay | read-write | current | Start day of the Schedule entry. The value must be from 1 to 31. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.7 | ColumnswTimeRangeStartHour | read-write | current | Start hour of the Schedule entry. The value must be from 0 to 23. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.8 | ColumnswTimeRangeStartMinute | read-write | current | Start minute of the Schedule entry. The value must be from 0 to 59. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.9 | ColumnswTimeRangeEndYear | read-write | current | End year of the Schedule entry. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.10 | ColumnswTimeRangeEndMonth | read-write | current | End month of the Schedule entry. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.11 | ColumnswTimeRangeEndDay | read-write | current | End day of the Schedule entry. The value must be from 1 to 31. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.12 | ColumnswTimeRangeEndHour | read-write | current | End hour of the Schedule entry. The value must be from 0 to 23. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.13 | ColumnswTimeRangeEndMinute | read-write | current | End minute of the Schedule entry. The value must be from 0 to 59. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.14 | ColumnswTimeRangeMonday | read-write | current | Enable/Disble scheduling Monday. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.15 | ColumnswTimeRangeTuesday | read-write | current | Enable/Disble scheduling Tuesday. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.16 | ColumnswTimeRangeWednesday | read-write | current | Enable/Disble scheduling Wednesday. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.17 | ColumnswTimeRangeThursday | read-write | current | Enable/Disble scheduling Thursday. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.18 | ColumnswTimeRangeFriday | read-write | current | Enable/Disble scheduling Friday. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.19 | ColumnswTimeRangeSaturday | read-write | current | Enable/Disble scheduling Saturday. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.20 | ColumnswTimeRangeSunday | read-write | current | Enable/Disble scheduling Sunday. |
| 1.3.6.1.4.1.171.10.76.22.1.32.1.1.21 | ColumnswTimeRangeRowStatus | read-create | current | The status of an entry in the Time Range Information Table. Only a subset of the rowstatus variables (active, notinservice, createAndWait, destroy) are availab… |
| 1.3.6.1.4.1.171.10.76.22.1.35 | NodecompanyStaticMcast | |||
| 1.3.6.1.4.1.171.10.76.22.1.35.1 | TablestaticMcastTable | not-accessible | current | A list of the Static MACs |
| 1.3.6.1.4.1.171.10.76.22.1.35.1.1 | RowstaticMcastEntry | not-accessible | current | A Static MAC entry containing the mac and forwarding port. |
| 1.3.6.1.4.1.171.10.76.22.1.35.1.1.1 | ColumnstaticMcastVlanID | read-only | current | The VLAN ID of the static MAC entry. |
| 1.3.6.1.4.1.171.10.76.22.1.35.1.1.2 | ColumnstaticMcastMac | read-only | current | The MAC address associated of the static MAC entry. |
| 1.3.6.1.4.1.171.10.76.22.1.35.1.1.3 | ColumnstaticMcastEgressPorts | read-only | current | The set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast MAC address must be forwarded, regardless of … |
| 1.3.6.1.4.1.171.10.76.22.1.35.1.1.4 | ColumnstaticMcastStatus | read-write | current | The status of an entry in the Static Mcast Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
| 1.3.6.1.4.1.171.10.76.22.1.37 | NodecompanyCableDiagnostic | |||
| 1.3.6.1.4.1.171.10.76.22.1.37.1 | ScalarcableDiagTriggerIndex | read-write | current | Trigger an interface index to do cable diagnostic. |
| 1.3.6.1.4.1.171.10.76.22.1.37.2 | ScalarcableDiagPair1TestResult | read-only | current | Cable diagnostics pair 1 test result. |
| 1.3.6.1.4.1.171.10.76.22.1.37.3 | ScalarcableDiagPair1FaultDistance | read-only | current | Cable Diagnostics pair 1 fault distance. |
| 1.3.6.1.4.1.171.10.76.22.1.37.4 | ScalarcableDiagPair2TestResult | read-only | current | Cable diagnostics pair 2 test result. |
| 1.3.6.1.4.1.171.10.76.22.1.37.5 | ScalarcableDiagPair2FaultDistance | read-only | current | Cable diagnostics pair 2 fault distance. |
| 1.3.6.1.4.1.171.10.76.22.1.37.6 | ScalarcableDiagPair3TestResult | read-only | current | Cable diagnostics pair 3 test result. |
| 1.3.6.1.4.1.171.10.76.22.1.37.7 | ScalarcableDiagPair3FaultDistance | read-only | current | Cable diagnostics pair 3 fault distance. |
| 1.3.6.1.4.1.171.10.76.22.1.37.8 | ScalarcableDiagPair4TestResult | read-only | current | Cable diagnostics pair 4 test result. |
| 1.3.6.1.4.1.171.10.76.22.1.37.9 | ScalarcableDiagPair4FaultDistance | read-only | current | Cable diagnostics pair 4 fault distance. |
| 1.3.6.1.4.1.171.10.76.22.1.37.10 | ScalarcableDiagLengthinRange | read-only | current | Cable diagnostics length when link up in speed 1G. (Display in range) |
| 1.3.6.1.4.1.171.10.76.22.1.47 | NodecompanyRMON | |||
| 1.3.6.1.4.1.171.10.76.22.1.47.1 | ScalarrmonGlobalState | read-write | current | This object is for enabling or disabling RMON function. |
| 1.3.6.1.4.1.171.10.76.22.1.47.2 | NodermonStatistics | |||
| 1.3.6.1.4.1.171.10.76.22.1.47.2.1 | TablermonStatsTable | not-accessible | current | A list of Ethernet statistics entries. |
| 1.3.6.1.4.1.171.10.76.22.1.47.2.1.1 | RowrmonStatsEntry | not-accessible | current | A collection of statistics kept for a particular Ethernet interface. As an example, an instance of the etherStatsPkts object might be named etherStatsPkts.1 |
| 1.3.6.1.4.1.171.10.76.22.1.47.2.1.1.1 | ColumnrmonStatsIndex | read-only | current | The value of this object uniquely identifies this etherStats entry. |
| 1.3.6.1.4.1.171.10.76.22.1.47.2.1.1.2 | ColumnrmonStatsDataSource | read-create | current | This object identifies the source of the data that this etherStats entry is configured to analyze. This source can be any ethernet interface on this device. In… |
| 1.3.6.1.4.1.171.10.76.22.1.47.2.1.1.3 | ColumnrmonStatsOwner | read-create | current | The entity that configured this entry and is therefore using the resources assigned to it. |
| 1.3.6.1.4.1.171.10.76.22.1.47.2.1.1.4 | ColumnrmonStatsStatus | read-create | current | The status of this etherStats entry. |
| 1.3.6.1.4.1.171.10.76.22.1.47.3 | NodermonHistory | |||
| 1.3.6.1.4.1.171.10.76.22.1.47.3.1 | TablermonHistoryTable | not-accessible | current | A list of history control entries. |
| 1.3.6.1.4.1.171.10.76.22.1.47.3.1.1 | RowrmonHistoryEntry | not-accessible | current | A list of parameters that set up a periodic sampling of statistics. As an example, an instance of the historyControlInterval object might be named historyContr… |
| 1.3.6.1.4.1.171.10.76.22.1.47.3.1.1.1 | ColumnrmonHistoryIndex | read-only | current | An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on t… |
| 1.3.6.1.4.1.171.10.76.22.1.47.3.1.1.2 | ColumnrmonHistoryDataSource | read-create | current | This object identifies the source of the data for which historical data was collected and placed in a media-specific table on behalf of this historyControlEntr… |
| 1.3.6.1.4.1.171.10.76.22.1.47.3.1.1.3 | ColumnrmonHistoryBucketsRequested | read-create | current | The requested number of discrete time intervals over which data is to be saved in the part of the media-specific table associated with this historyControlEntry… |
| 1.3.6.1.4.1.171.10.76.22.1.47.3.1.1.4 | ColumnrmonHistoryInterval | read-create | current | The interval in seconds over which the data is sampled for each bucket in the part of the media-specific table associated with this historyControlEntry. This i… |
| 1.3.6.1.4.1.171.10.76.22.1.47.3.1.1.5 | ColumnrmonHistoryOwner | read-create | current | The entity that configured this entry and is therefore using the resources assigned to it. |
| 1.3.6.1.4.1.171.10.76.22.1.47.3.1.1.6 | ColumnrmonHistoryStatus | read-create | current | The status of this historyControl entry. Each instance of the media-specific table associated with this historyControlEntry will be deleted by the agent if thi… |
| 1.3.6.1.4.1.171.10.76.22.1.47.4 | NodermonAlarm | |||
| 1.3.6.1.4.1.171.10.76.22.1.47.4.1 | TablermonAlarmTable | not-accessible | current | A list of alarm entries. |
| 1.3.6.1.4.1.171.10.76.22.1.47.4.1.1 | RowrmonAlarmEntry | not-accessible | current | A list of parameters that set up a periodic checking for alarm conditions. For example, an instance of the alarmValue object might be named alarmValue.8 |
| 1.3.6.1.4.1.171.10.76.22.1.47.4.1.1.1 | ColumnrmonAlarmIndex | read-only | current | An index that uniquely identifies an entry in the alarm table. Each such entry defines a diagnostic sample at a particular interval for an object on the device. |
| 1.3.6.1.4.1.171.10.76.22.1.47.4.1.1.2 | ColumnrmonAlarmInterval | read-create | current | The interval in seconds over which the data is sampled and compared with the rising and falling thresholds. When setting this variable, care should be taken in… |
| 1.3.6.1.4.1.171.10.76.22.1.47.4.1.1.3 | ColumnrmonAlarmVariable | read-create | current | The object identifier of the particular variable to be sampled. Only variables that resolve to an ASN.1 primitive type of INTEGER (INTEGER, Integer32, Counter3… |
| 1.3.6.1.4.1.171.10.76.22.1.47.4.1.1.4 | ColumnrmonAlarmSampleType | read-create | current | The method of sampling the selected variable and calculating the value to be compared against the thresholds. If the value of this object is absoluteValue(1), … |
| 1.3.6.1.4.1.171.10.76.22.1.47.4.1.1.5 | ColumnrmonAlarmRisingThreshold | read-create | current | A threshold for the sampled statistic. When the current sampled value is greater than or equal to this threshold, and the value at the last sampling interval w… |
| 1.3.6.1.4.1.171.10.76.22.1.47.4.1.1.6 | ColumnrmonAlarmFallingThreshold | read-create | current | A threshold for the sampled statistic. When the current sampled value is less than or equal to this threshold, and the value at the last sampling interval was … |
| 1.3.6.1.4.1.171.10.76.22.1.47.4.1.1.7 | ColumnrmonAlarmRisingEventIndex | read-create | current | The index of the eventEntry that is used when a rising threshold is crossed. The eventEntry identified by a particular value of this index is the same as ident… |
| 1.3.6.1.4.1.171.10.76.22.1.47.4.1.1.8 | ColumnrmonAlarmFallingEventIndex | read-create | current | The index of the eventEntry that is used when a falling threshold is crossed. The eventEntry identified by a particular value of this index is the same as iden… |
| 1.3.6.1.4.1.171.10.76.22.1.47.4.1.1.9 | ColumnrmonAlarmOwner | read-create | current | The entity that configured this entry and is therefore using the resources assigned to it. |
| 1.3.6.1.4.1.171.10.76.22.1.47.4.1.1.10 | ColumnrmonAlarmStatus | read-create | current | The status of this alarm entry. |
| 1.3.6.1.4.1.171.10.76.22.1.47.5 | NodermonEvent | |||
| 1.3.6.1.4.1.171.10.76.22.1.47.5.1 | TablermonEventTable | not-accessible | current | A list of events to be generated. |
| 1.3.6.1.4.1.171.10.76.22.1.47.5.1.1 | RowrmonEventEntry | not-accessible | current | A set of parameters that describe an event to be generated when certain conditions are met. As an example, an instance of the eventLastTimeSent object might be… |
| 1.3.6.1.4.1.171.10.76.22.1.47.5.1.1.1 | ColumnrmonEventIndex | read-only | current | An index that uniquely identifies an entry in the event table. Each such entry defines one event that is to be generated when the appropriate conditions occur. |
| 1.3.6.1.4.1.171.10.76.22.1.47.5.1.1.2 | ColumnrmonEventDescription | read-create | current | A comment describing this event entry. |
| 1.3.6.1.4.1.171.10.76.22.1.47.5.1.1.3 | ColumnrmonEventType | read-create | current | The type of notification that the probe will make about this event. In the case of log, an entry is made in the log table for each event. In the case of snmp-t… |
| 1.3.6.1.4.1.171.10.76.22.1.47.5.1.1.4 | ColumnrmonEventCommunity | read-create | current | If an SNMP trap is to be sent, it will be sent to the SNMP community specified by this octet string. |
| 1.3.6.1.4.1.171.10.76.22.1.47.5.1.1.5 | ColumnrmonEventOwner | read-create | current | The entity that configured this entry and is therefore using the resources assigned to it. If this object contains a string starting with 'monitor' and has ass… |
| 1.3.6.1.4.1.171.10.76.22.1.47.5.1.1.6 | ColumnrmonEventStatus | read-create | current | The status of this event entry. If this object is not equal to valid(1), all associated log entries shall be deleted by the agent. |
| 1.3.6.1.4.1.171.10.76.22.1.50 | NodecompanyNeighbor | |||
| 1.3.6.1.4.1.171.10.76.22.1.50.1 | TableneighborTable | not-accessible | current | A list of the Neighbor Cache Table. |
| 1.3.6.1.4.1.171.10.76.22.1.50.1.1 | RowneighborEntry | not-accessible | current | A Neighbor cache entry containing the ifindex and ipv6 addr. |
| 1.3.6.1.4.1.171.10.76.22.1.50.1.1.1 | ColumnneighborIfindex | read-only | current | The interface index of the Neighbor entry. |
| 1.3.6.1.4.1.171.10.76.22.1.50.1.1.2 | ColumnneighborIPv6Addr | read-only | current | Allows the entry of an IP address that will be a Neighbor entry into the Neighbor Cache Table. |
| 1.3.6.1.4.1.171.10.76.22.1.50.1.1.3 | ColumnneighborMACAddr | read-only | current | The MAC address associated of the Neighbor entry. |
| 1.3.6.1.4.1.171.10.76.22.1.50.1.1.4 | ColumnneighborType | read-only | current | The type associated of the Neighbor entry. |
| 1.3.6.1.4.1.171.10.76.22.1.50.1.1.5 | ColumnneighborCacheState | read-only | current | The type associated of the Neighbor entry. |
| 1.3.6.1.4.1.171.10.76.22.1.50.1.1.7 | ColumnneighborRowStatus | read-write | current | The status of an entry in the Neighbor Cache Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
| 1.3.6.1.4.1.171.10.76.22.1.52 | Nodecompanydot3azEEE | |||
| 1.3.6.1.4.1.171.10.76.22.1.52.1 | Nodedot3azEEEset | |||
| 1.3.6.1.4.1.171.10.76.22.1.52.1.1 | Tabledot3azTable | not-accessible | current | A table to control IEEE802.3az EEE settings features of the device. |
| 1.3.6.1.4.1.171.10.76.22.1.52.1.1.1 | Rowdot3azEntry | not-accessible | current | An entry appears in IEEE802.3az EEE table for each interface in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.52.1.1.1.1 | ColumnportD3Index | read-only | current | The interface index for which the configuration in this entry applies. |
| 1.3.6.1.4.1.171.10.76.22.1.52.1.1.1.2 | ColumnportD3State | read-write | current | Enable / disable port IEEE802.3az EEE admin state for the interface. A given ports' dynamic MAC address learning will be stopped such that the current source M… |
| 1.3.6.1.4.1.171.10.76.22.1.61 | NodecompanyDHCPRelay | |||
| 1.3.6.1.4.1.171.10.76.22.1.61.1 | NodedhcpRelayControl | |||
| 1.3.6.1.4.1.171.10.76.22.1.61.1.1 | ScalardhcpRelayState | read-write | current | This object indicates DHCP relay function is enabled or disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.61.1.2 | ScalardhcpRelayHopCount | read-write | current | This object indicates the maximum number of router hops that the packets can cross. |
| 1.3.6.1.4.1.171.10.76.22.1.61.1.3 | ScalardhcpRelayTimeThreshold | read-write | current | This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP … |
| 1.3.6.1.4.1.171.10.76.22.1.61.2 | NodedhcpRelayManagement | |||
| 1.3.6.1.4.1.171.10.76.22.1.61.2.1 | TabledhcpRelayInterfaceSettingsTable | not-accessible | current | This table indicates the IP address as a destination to forward (relay) DHCP packets to. |
| 1.3.6.1.4.1.171.10.76.22.1.61.2.1.1 | RowdhcpRelayInterfaceSettingsEntry | not-accessible | current | A list of information indicates the IP address as a destination to forward (relay) DHCP packets to. |
| 1.3.6.1.4.1.171.10.76.22.1.61.2.1.1.1 | ColumndhcpRelayInterface | read-only | current | This object indicates the name of the IP interface. |
| 1.3.6.1.4.1.171.10.76.22.1.61.2.1.1.2 | ColumndhcpRelayServerIP | read-only | current | This object indicates the DHCP server IP address. |
| 1.3.6.1.4.1.171.10.76.22.1.61.2.1.1.3 | ColumndhcpRelayInterfaceSettingsRowStatus | read-create | current | This object indicates the status of this entry. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
| 1.3.6.1.4.1.171.10.76.22.1.61.2.2 | NodedhcpRelayManagementOption82 | |||
| 1.3.6.1.4.1.171.10.76.22.1.61.2.2.1 | ScalardhcpRelayOption82State | read-only | current | This object indicates DHCP relay option 82 function always enabled. |
| 1.3.6.1.4.1.171.10.76.22.1.61.2.2.2 | ScalardhcpRelayOption82CheckState | read-write | current | This object indicates DHCP relay option 82 Check function is enabled or disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.61.2.2.3 | ScalardhcpRelayOption82Policy | read-write | current | This object indicates DHCP relay option 82 policy. |
| 1.3.6.1.4.1.171.10.76.22.1.61.2.2.4 | ScalardhcpRelayOption82RemoteIDType | read-write | current | This object indicates the type of remote ID. If the type is default, the remote ID will be the MAC address of the device, otherwise, the remote ID can be defin… |
| 1.3.6.1.4.1.171.10.76.22.1.61.2.2.5 | ScalardhcpRelayOption82RemoteID | read-write | current | This object displays the current remote ID of the device. If swDHCPRelayOption82RemoteIDType is set to default, the value will be the MAC address of the device… |
| 1.3.6.1.4.1.171.10.76.22.1.62 | NodecompanyDHCPLocalRelay | |||
| 1.3.6.1.4.1.171.10.76.22.1.62.1 | ScalardhcpLocalRelayGlobalState | read-write | current | This object indicates DHCP local relay function of VLAN is enabled or disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.62.2 | TabledhcpLocalRelayTable | not-accessible | current | This table indicates the IP address as a destination to forward (local relay) DHCP packets to. |
| 1.3.6.1.4.1.171.10.76.22.1.62.2.1 | RowdhcpLocalRelayEntry | not-accessible | current | A list of information indicates the IP address as a destination to forward (local relay) DHCP packets to. |
| 1.3.6.1.4.1.171.10.76.22.1.62.2.1.1 | ColumndhcpLocalRelaySettingsVLANID | read-only | current | This object displays the current VLAN ID of the device. |
| 1.3.6.1.4.1.171.10.76.22.1.62.2.1.2 | ColumndhcpLocalRelaySettingsState | read-write | current | This object indicates DHCP local relay function of VLAN is enabled or disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.63 | NodecompanyDHCPv6Relay | |||
| 1.3.6.1.4.1.171.10.76.22.1.63.1 | Nodedhcpv6RelayControl | |||
| 1.3.6.1.4.1.171.10.76.22.1.63.1.1 | Scalardhcpv6RelayState | read-write | current | This object indicates DHCPv6 relay function is enabled or disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.63.1.2 | Scalardhcpv6RelayHopCount | read-write | current | This object indicates the maximum number of router hops that the DHCPv6 packets can cross. |
| 1.3.6.1.4.1.171.10.76.22.1.63.2 | Nodedhcpv6RelayManagement | |||
| 1.3.6.1.4.1.171.10.76.22.1.63.2.1 | Tabledhcpv6RelayInterfaceSettingsTable | not-accessible | current | This table indicates the IP address as a destination to forward (relay) DHCP packets to. |
| 1.3.6.1.4.1.171.10.76.22.1.63.2.1.1 | Rowdhcpv6RelayInterfaceSettingsEntry | not-accessible | current | A list of information indicates the IP address as a destination to forward (relay) DHCP packets to. |
| 1.3.6.1.4.1.171.10.76.22.1.63.2.1.1.1 | Columndhcpv6RelayInterface | read-only | current | This object indicates the maximum number of router hops that the DHCPv6 packets can cross. |
| 1.3.6.1.4.1.171.10.76.22.1.63.2.1.1.2 | Columndhcpv6RelayServerIP | read-only | current | This object indicates the DHCP server IP address. |
| 1.3.6.1.4.1.171.10.76.22.1.63.2.1.1.99 | Columndhcpv6RelayInterfaceSettingsRowStatus | read-create | current | This object indicates the status of this entry. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
| 1.3.6.1.4.1.171.10.76.22.1.63.3 | Nodedhcpv6RelayOption37 | |||
| 1.3.6.1.4.1.171.10.76.22.1.63.3.1 | Scalardhcpv6RelayOption37State | read-write | current | This object indicates DHCPv6 relay option 37 function is enabled or disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.63.3.2 | Scalardhcpv6RelayOption37CheckState | read-write | current | This object indicates DHCPv6 relay option 37 Check function is enabled or disabled. |
| 1.3.6.1.4.1.171.10.76.22.1.63.3.3 | Scalardhcpv6RelayOption37RemoteIDType | read-write | current | This object indicates the type of remote ID. |
| 1.3.6.1.4.1.171.10.76.22.1.63.3.4 | Scalardhcpv6RelayOption37RemoteID | read-write | current | This object displays the current remote ID of the device. If RemoteIDType is set to default, the value will be the MAC address of the device, and this object c… |
| 1.3.6.1.4.1.171.10.76.22.1.88 | NodecompanyMldsGroup | |||
| 1.3.6.1.4.1.171.10.76.22.1.88.1 | NodemldsSystem | |||
| 1.3.6.1.4.1.171.10.76.22.1.88.1.1 | ScalarmldsStatus | read-write | current | Enables or disables MLD snooping in the system. When set to 'enabled', the MLDS module starts protocol operations. When set to 'disabled', the MLDS module stop… |
| 1.3.6.1.4.1.171.10.76.22.1.88.1.2 | ScalarmldsRouterPortPurgeInterval | read-write | current | This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInter… |
| 1.3.6.1.4.1.171.10.76.22.1.88.1.3 | ScalarmldsHostPortPurgeInterval | read-write | current | This is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received this timer runs for 'PortPurg… |
| 1.3.6.1.4.1.171.10.76.22.1.88.1.4 | ScalarmldsRobustnessValue | read-write | current | When the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attrib… |
| 1.3.6.1.4.1.171.10.76.22.1.88.1.5 | ScalarmldsGrpQueryInterval | read-write | current | The value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there is any intersted receive… |
| 1.3.6.1.4.1.171.10.76.22.1.88.1.6 | ScalarmldsQueryInterval | read-write | current | This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for VLANs. |
| 1.3.6.1.4.1.171.10.76.22.1.88.1.7 | ScalarmldsQueryMaxResponseTime | read-write | current | The maximum query response time advertised in MLDv1 general queries on this interface. |
| 1.3.6.1.4.1.171.10.76.22.1.88.3 | NodemldsVlan | |||
| 1.3.6.1.4.1.171.10.76.22.1.88.3.3 | TablemldsVlanRouterTable | not-accessible | current | This table contains the list of ports through which a router, in a particular VLAN is reachable. |
| 1.3.6.1.4.1.171.10.76.22.1.88.3.3.1 | RowmldsVlanRouterEntry | not-accessible | current | Contains the VLAN ID and list of ports on which routers are present in the VLAN. |
| 1.3.6.1.4.1.171.10.76.22.1.88.3.3.1.1 | ColumnmldsVlanRouterVlanId | read-only | current | VLAN ID of the ports through which router is reachable. |
| 1.3.6.1.4.1.171.10.76.22.1.88.3.3.1.2 | ColumnmldsVlanRouterPortList | read-only | current | List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically. |
| 1.3.6.1.4.1.171.10.76.22.1.88.3.4 | TablemldsVlanFilterTable | not-accessible | current | This table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system. |
| 1.3.6.1.4.1.171.10.76.22.1.88.3.4.1 | RowmldsVlanFilterEntry | not-accessible | current | Contains snooping status , version and fast leave configuration for a specific VLAN. |
| 1.3.6.1.4.1.171.10.76.22.1.88.3.4.1.1 | ColumnmldsVlanFilterVlanId | read-only | current | Index of MldsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in MldsVlanFilterEntry is to be done. |
| 1.3.6.1.4.1.171.10.76.22.1.88.3.4.1.2 | ColumnmldsVlanSnoopStatus | read-write | current | This object allows you to enable/disable MLDS function on a specific VLAN. |
| 1.3.6.1.4.1.171.10.76.22.1.88.3.4.1.3 | ColumnmldsVlanQuerier | read-only | current | Indicates whether the switch is configured as a querier in the VLAN |
| 1.3.6.1.4.1.171.10.76.22.1.88.3.4.1.4 | ColumnmldsVlanCfgQuerier | read-write | current | The snooping switch can be configured as a querier via this object to send out MLD general queries when IGMP routers are not present in the VLAN. When set to '… |
| 1.3.6.1.4.1.171.10.76.22.1.88.3.4.1.5 | ColumnmldsVlanQueryInterval | read-only | current | This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as … |
| 1.3.6.1.4.1.171.10.76.22.1.88.3.4.1.6 | ColumnmldsVlanRtrPortList | read-write | current | List of ports which are configured statically as router ports |
| 1.3.6.1.4.1.171.10.76.22.1.88.3.4.1.8 | ColumnmldsVlanFastLeave | read-write | current | Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for … |
| 1.3.6.1.4.1.171.10.76.22.1.88.3.5 | TablemldsVlanMulticastGroupTable | not-accessible | current | This table contains MAC based multicast forwarding information. |
| 1.3.6.1.4.1.171.10.76.22.1.88.3.5.1 | RowmldsVlanMulticastGroupEntry | not-accessible | current | This table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded. |
| 1.3.6.1.4.1.171.10.76.22.1.88.3.5.1.1 | ColumnmldsVlanMulticastGroupVlanId | read-only | current | VLAN ID pertaining to the Multicast forwarding entry |
| 1.3.6.1.4.1.171.10.76.22.1.88.3.5.1.2 | ColumnmldsVlanMulticastGroupIpAddress | read-only | current | Multicast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format. |
| 1.3.6.1.4.1.171.10.76.22.1.88.3.5.1.3 | ColumnmldsVlanMulticastGroupMacAddress | read-only | current | Multicast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format. |
| 1.3.6.1.4.1.171.10.76.22.1.88.3.5.1.4 | ColumnmldsVlanMulticastGroupPortList | read-only | current | List of ports onto which the multicast data packets destined for this group will be forwarded. |
| 1.3.6.1.4.1.171.10.76.22.1.99 | NodecompanyDoSCtrl | |||
| 1.3.6.1.4.1.171.10.76.22.1.99.1 | ScalardoSCtrlState | read-write | current | This object indicates the status of the DoS prevention type. |
| 1.3.6.1.4.1.171.10.76.22.1.99.2 | TabledoSCtrlTable | not-accessible | current | A table that holds the DoS prevention settings of the device. |
| 1.3.6.1.4.1.171.10.76.22.1.99.2.1 | RowdoSCtrlEntry | not-accessible | current | A list of DoS prevention settings of the device. |
| 1.3.6.1.4.1.171.10.76.22.1.99.2.1.1 | ColumndoSCtrlType | read-only | current | This object indicates the DoS prevention type. |
| 1.3.6.1.4.1.171.10.76.22.1.99.2.1.2 | ColumndoSCtrlDisplayState | read-only | current | This object indicates the status of the DoS prevention type. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| BridgeId | OCTET STRING (SIZE (8)) | current | The Bridge-Identifier as used in the Spanning Tree Protocol to uniquely identify a bridge. Its first two octets (in network byte order) contain a priority value and its last 6 octets contain the MAC address used to refe… |
| Ipv6Address | OCTET STRING (SIZE (16)) | current | This data type is used to model IPv6 addresses. This is a binary string of 16 octets in network byte-order. |
| LacpKey | Integer32 (0..65535) | current | The Actor or Partner Key value (0..65535). |
| LldpManAddress | OCTET STRING (SIZE (1..31)) | current | The value of a management address associated with the LLDP agent that may be used to reach higher layer entities to assist discovery by network management. It should be noted that appropriate security credentials, such … |
| PortLaMode | INTEGER { lacp(1), static(2), disable(3) } | current | Defines how a Port Channel does channeling. lacp(1) - place the port into passive negotiation state, in which the port waits for its peer to initiate negotiation. static(2) - force the port to enable channeling. disable… |
| PortList | OCTET STRING | current | Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents… |
| RmonStatus | INTEGER { valid(1), createRequest(2), underCreation(3), invalid(4) } | current | The status of a table entry. Setting this object to the value invalid(4) has the effect of invalidating the corresponding entry. That is, it effectively disassociates the mapping identified with said entry. It is an imp… |
| Timeout | INTEGER | current | A STP timer in units of 1/100 seconds To convert a Timeout value into a value in units of 1/256 seconds, the following algorithm should be used: b = floor( (n * 256) / 100) where: floor = quotient [ignore remainder] n i… |
| VlanIndex | Unsigned32 | current | A value used to index per-VLAN tables: values of 0 and 4095 are not permitted; if the value is between 1 and 4094 inclusive, it represents an IEEE 802.1Q VLAN-ID with global scope within a given bridged domain (see Vlan… |