DGS3612G-L2MGMT-MIB
364 objects
The Structure of Layer 2 Network Management Information.
Imported Objects
| DLINK-ID-REC-MIB | AgentNotifyLevel |
| Q-BRIDGE-MIB | --PortList |
| RFC1155-SMI | Counter |
| SNMPv2-SMI | Integer32 IpAddress MODULE-IDENTITY OBJECT-TYPE TimeTicks |
| SNMPv2-TC | DisplayString RowStatus TEXTUAL-CONVENTION |
| SW36XXPRIMGMT-MIB | dgs3612g |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.171.11.70.9.2 | IdentityswL2MgmtMIB | The Structure of Layer 2 Network Management Information. | ||
| 1.3.6.1.4.1.171.11.70.9.2.1 | NodeswL2DevMgmt | |||
| 1.3.6.1.4.1.171.11.70.9.2.1.1 | NodeswL2DevInfo | |||
| 1.3.6.1.4.1.171.11.70.9.2.1.1.1 | ScalarswDevInfoTotalNumOfPort | read-only | current | The number of ports within this switch. This value is the sum of the ports within this switch. |
| 1.3.6.1.4.1.171.11.70.9.2.1.1.2 | ScalarswDevInfoNumOfPortInUse | read-only | current | The number of ports in this switch connected to the segment or the end stations. |
| 1.3.6.1.4.1.171.11.70.9.2.1.1.3 | TableswDevModuleInfoTable | not-accessible | current | This table contains the module information. |
| 1.3.6.1.4.1.171.11.70.9.2.1.1.3.1 | RowswDevModuleInfoEntry | not-accessible | current | A list of management information for each unit in the system. |
| 1.3.6.1.4.1.171.11.70.9.2.1.1.3.1.1 | ColumnswDevModuleInfoUnitID | read-only | current | This object indicates the specific unit ID in the stacking/chassis table. |
| 1.3.6.1.4.1.171.11.70.9.2.1.1.3.1.2 | ColumnswDevModuleInfoModuleID | read-only | current | This object indicates the module ID of this unit. |
| 1.3.6.1.4.1.171.11.70.9.2.1.1.3.1.3 | ColumnswDevModuleInfoModuleName | read-only | current | A textual string containing name of the the module. |
| 1.3.6.1.4.1.171.11.70.9.2.1.1.3.1.4 | ColumnswDevModuleInfoReversion | read-only | current | A textual string containing reversion of the module. |
| 1.3.6.1.4.1.171.11.70.9.2.1.1.3.1.5 | ColumnswDevModuleInfoSerial | read-only | current | A textual string containing serial of the module. |
| 1.3.6.1.4.1.171.11.70.9.2.1.1.3.1.6 | ColumnswDevModuleInfoDescription | read-only | current | A textual string containing description of the module. |
| 1.3.6.1.4.1.171.11.70.9.2.1.1.4 | ScalarswDevInfoBootPromVersion | read-only | current | Boot Prom Version. |
| 1.3.6.1.4.1.171.11.70.9.2.1.1.5 | ScalarswDevInfoFirmwareVersion | read-only | current | Boot firmware Version. |
| 1.3.6.1.4.1.171.11.70.9.2.1.1.6 | ScalarswDevInfoFrontPanelLedStatus | read-only | current | This object is a set of system LED indications. The first two octets is defined as system LED. The first LED is power LED. The second LED is console LED. The t… |
| 1.3.6.1.4.1.171.11.70.9.2.1.2 | NodeswL2DevCtrl | |||
| 1.3.6.1.4.1.171.11.70.9.2.1.2.1 | ScalarswL2DevCtrlStpState | read-write | current | This object can be enabled or disabled spanning tree algorithm during runtime of the system. |
| 1.3.6.1.4.1.171.11.70.9.2.1.2.2 | ScalarswL2DevCtrlIGMPSnooping | read-write | current | This object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled. |
| 1.3.6.1.4.1.171.11.70.9.2.1.2.3 | ScalarswL2DevCtrlIGMPSnoopingMcstRTOnly | read-write | current | |
| 1.3.6.1.4.1.171.11.70.9.2.1.2.4 | ScalarswL2DevCtrlRmonState | read-write | current | This object can be enabled or disabled RMON. |
| 1.3.6.1.4.1.171.11.70.9.2.1.2.5 | ScalarswL2DevCtrlCleanAllStatisticCounter | read-write | current | As the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing. |
| 1.3.6.1.4.1.171.11.70.9.2.1.2.6 | ScalarswL2DevCtrlVlanIdOfFDBTbl | read-write | current | Indicates the VLAN ID which the Dot1dTpFdbTable belongs to ; The default value is DEFAULT_VLAN_ID of system . |
| 1.3.6.1.4.1.171.11.70.9.2.1.2.7 | ScalarswL2DevCtrlManagementVlanId | read-write | current | This object controls which Vlan includes system ip. And the Vlan should have been created. |
| 1.3.6.1.4.1.171.11.70.9.2.1.2.8 | ScalarswL2MACNotifyState | read-write | current | This object can enabled or disabled MAC Notification. |
| 1.3.6.1.4.1.171.11.70.9.2.1.2.9 | ScalarswL2MACNotifyHistorySize | read-write | current | This object indicates the history size of variation MAC in address table. The default value is 1 . |
| 1.3.6.1.4.1.171.11.70.9.2.1.2.10 | ScalarswL2MACNotifyInterval | read-write | current | This object indicates the time interval in second for trigger the MAC notify message. |
| 1.3.6.1.4.1.171.11.70.9.2.1.2.13 | NodeswL2DevCtrlWeb | |||
| 1.3.6.1.4.1.171.11.70.9.2.1.2.13.1 | ScalarswL2DevCtrlWebState | read-write | current | This object control web status. |
| 1.3.6.1.4.1.171.11.70.9.2.1.2.13.2 | ScalarswL2DevCtrlWebTcpPort | read-write | current | This object can designate tcp port. When web disable this object can't accessible. |
| 1.3.6.1.4.1.171.11.70.9.2.1.2.14 | NodeswL2DevCtrlTelnet | |||
| 1.3.6.1.4.1.171.11.70.9.2.1.2.14.1 | ScalarswL2DevCtrlTelnetState | read-write | current | This object control telnet status. |
| 1.3.6.1.4.1.171.11.70.9.2.1.2.14.2 | ScalarswL2DevCtrlTelnetTcpPort | read-write | current | This object can designate tcp port. When telnet disable this object can't accessible. |
| 1.3.6.1.4.1.171.11.70.9.2.1.2.15 | ScalarswL2DevCtrlIpAutoconfig | read-write | current | |
| 1.3.6.1.4.1.171.11.70.9.2.1.2.16 | ScalarswL2DevCtrlLedPOEState | read-write | current | When set enabled(1), the POE LED is lighten. When set disabled(2), the Link/ACT/Speed LED is lighten. |
| 1.3.6.1.4.1.171.11.70.9.2.1.2.17 | ScalarswL2DevCtrlClipagingState | read-write | current | |
| 1.3.6.1.4.1.171.11.70.9.2.1.2.18 | ScalarswL2DevCtrlLLDPState | read-write | current | Specifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets… |
| 1.3.6.1.4.1.171.11.70.9.2.1.2.19 | ScalarswL2DevCtrlLLDPForwardMessageState | read-write | current | When lldp is disabled and lldp forward_message's are enabled, the LLDP Data Unit packets received by the switch will be forwarded. |
| 1.3.6.1.4.1.171.11.70.9.2.1.2.22 | ScalarswL2DevCtrlVLANTrunkState | read-write | current | This indicates the global state of the VLAN trunking feature of the device. |
| 1.3.6.1.4.1.171.11.70.9.2.1.3 | NodeswL2DevAlarm | |||
| 1.3.6.1.4.1.171.11.70.9.2.1.3.1 | ScalarswL2DevAlarmNewRoot | read-write | current | When the device has become the new root of the Spanning Tree, this object decide whether to send a new root trap. |
| 1.3.6.1.4.1.171.11.70.9.2.1.3.2 | ScalarswL2DevAlarmTopologyChange | read-write | current | This object determine to send a trap or not when the switch topology was changed. If the object is enabled(3), the topologyChange trap is sent by the device wh… |
| 1.3.6.1.4.1.171.11.70.9.2.1.3.3 | ScalarswL2DevAlarmLinkChange | read-write | current | This object determine to send a trap or not when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its … |
| 1.3.6.1.4.1.171.11.70.9.2.2 | NodeswL2MultiFilter | |||
| 1.3.6.1.4.1.171.11.70.9.2.2.1 | TableswL2MultiFilterTable | not-accessible | current | A table that contains infomation about vlan multicast filter mode. |
| 1.3.6.1.4.1.171.11.70.9.2.2.1.1 | RowswL2MultiFilterEntry | not-accessible | current | A list of multicast filter mode information for each vlan. |
| 1.3.6.1.4.1.171.11.70.9.2.2.1.1.1 | ColumnswL2MultiFilterVid | read-only | current | vid for each vlan |
| 1.3.6.1.4.1.171.11.70.9.2.2.1.1.2 | ColumnswL2MultiFilterMode | read-write | current | vlan multicast filter mode. |
| 1.3.6.1.4.1.171.11.70.9.2.3 | NodeswL2PortMgmt | |||
| 1.3.6.1.4.1.171.11.70.9.2.3.1 | TableswL2PortInfoTable | not-accessible | current | A table that contains information about every port. |
| 1.3.6.1.4.1.171.11.70.9.2.3.1.1 | RowswL2PortInfoEntry | not-accessible | current | A list of information for each port of the device. |
| 1.3.6.1.4.1.171.11.70.9.2.3.1.1.1 | ColumnswL2PortInfoPortIndex | read-only | current | This object indicates the module's port number.(1..Max port number in the module) |
| 1.3.6.1.4.1.171.11.70.9.2.3.1.1.2 | ColumnswL2PortInfoMediumType | read-only | current | Indicates medium type of the port number. |
| 1.3.6.1.4.1.171.11.70.9.2.3.1.1.3 | ColumnswL2PortInfoUnitID | read-only | current | Indicates ID of the unit in the system |
| 1.3.6.1.4.1.171.11.70.9.2.3.1.1.4 | ColumnswL2PortInfoType | read-only | current | This object indicates the connector type of this port. |
| 1.3.6.1.4.1.171.11.70.9.2.3.1.1.5 | ColumnswL2PortInfoLinkStatus | read-only | current | This object indicates the port link status. |
| 1.3.6.1.4.1.171.11.70.9.2.3.1.1.6 | ColumnswL2PortInfoNwayStatus | read-only | current | This object indicates the port speed and duplex mode. |
| 1.3.6.1.4.1.171.11.70.9.2.3.1.1.7 | ColumnswL2PortInfoErrDisReason | read-only | current | This object indicates the port if disabled and why error disabled. |
| 1.3.6.1.4.1.171.11.70.9.2.3.2 | TableswL2PortCtrlTable | not-accessible | current | A table that contains control information about every port. |
| 1.3.6.1.4.1.171.11.70.9.2.3.2.1 | RowswL2PortCtrlEntry | not-accessible | current | A list of control information for each port of the device. |
| 1.3.6.1.4.1.171.11.70.9.2.3.2.1.1 | ColumnswL2PortCtrlPortIndex | read-only | current | This object indicates the module's port number.(1..Max port number in the module) |
| 1.3.6.1.4.1.171.11.70.9.2.3.2.1.2 | ColumnswL2PortCtrlMediumType | read-only | current | Indicates medium type of the port number. |
| 1.3.6.1.4.1.171.11.70.9.2.3.2.1.3 | ColumnswL2PortCtrlUnitIndex | read-only | current | Indicates ID of the unit in the device |
| 1.3.6.1.4.1.171.11.70.9.2.3.2.1.4 | ColumnswL2PortCtrlAdminState | read-write | current | This object decide the port enabled or disabled. |
| 1.3.6.1.4.1.171.11.70.9.2.3.2.1.5 | ColumnswL2PortCtrlNwayState | read-write | current | Chose the port speed, duplex mode, and N-Way function mode. |
| 1.3.6.1.4.1.171.11.70.9.2.3.2.1.6 | ColumnswL2PortCtrlFlowCtrlState | read-write | current | The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mo… |
| 1.3.6.1.4.1.171.11.70.9.2.3.2.1.7 | ColumnswL2PortCtrlLockState | read-write | current | This object decide the port is locked or not. |
| 1.3.6.1.4.1.171.11.70.9.2.3.2.1.8 | ColumnswL2PortCtrlMACNotifyState | read-write | current | This object set each port MAC notification state. |
| 1.3.6.1.4.1.171.11.70.9.2.3.2.1.11 | ColumnswL2PortCtrlAutoNegRestart | read-write | current | If the value of this object is set to restart(1) then this will force auto-negotiation to begin link renegotiation. If auto-negotiation signaling is disabled, … |
| 1.3.6.1.4.1.171.11.70.9.2.3.2.1.12 | ColumnswL2PortCtrlAutoNegCapAdvertisedBits | read-write | current | A value that uniquely identifies the set of capabilities advertised by the local auto-negotiation entity. Capabilities in this object that are not available in… |
| 1.3.6.1.4.1.171.11.70.9.2.3.3 | ScalarswL2PortCtrlJumboFrame | read-write | current | This object configure the switch's jumbo frame settings. |
| 1.3.6.1.4.1.171.11.70.9.2.3.4 | ScalarswL2PortCtrlJumboFrameMaxSize | read-only | current | This object configure the switch's jumbo frame settings. |
| 1.3.6.1.4.1.171.11.70.9.2.3.8 | TableswL2PortAutoNegInfoTable | not-accessible | current | A table that contains information about every port's auto negotiation status. |
| 1.3.6.1.4.1.171.11.70.9.2.3.8.1 | RowswL2PortAutoNegInfoEntry | not-accessible | current | A list of information for each port auto negotiation of the device. |
| 1.3.6.1.4.1.171.11.70.9.2.3.8.1.1 | ColumnswL2PortAutoNegInfoPortIndex | read-only | current | This object indicates the module's port number.(1..Max port number in the module) |
| 1.3.6.1.4.1.171.11.70.9.2.3.8.1.2 | ColumnswL2PortAutoNegInfoAdminStatus | read-only | current | If the value of this object is disabled(2) then the interface will act as it would if it had no auto-negotiation signaling. The status is affect by setting swL… |
| 1.3.6.1.4.1.171.11.70.9.2.3.8.1.3 | ColumnswL2PortAutoNegInfoCapabilityBits | read-only | current | A value that uniquely identifies the set of capabilities of the local auto-negotiation entity. Note that interfaces that support this MIB may have capabilities… |
| 1.3.6.1.4.1.171.11.70.9.2.3.8.1.4 | ColumnswL2PortAutoNegInfoCapAdvertisedBits | read-only | current | A value that uniquely identifies the set of capabilities advertised by the local auto-negotiation entity. Capabilities in this object that are not available in… |
| 1.3.6.1.4.1.171.11.70.9.2.3.8.1.5 | ColumnswL2PortAutoNegInfoCapReceivedBits | read-only | current | A value that uniquely identifies the set of capabilities received from the remote auto-negotiation entity. Note that interfaces that support this MIB may be at… |
| 1.3.6.1.4.1.171.11.70.9.2.3.9 | TableswL2PortDropCounterTable | not-accessible | current | A table that contains information for each port drop counter. |
| 1.3.6.1.4.1.171.11.70.9.2.3.9.1 | RowswL2PortDropCounterEntry | not-accessible | current | A list of information for each port auto negotiation of the device. |
| 1.3.6.1.4.1.171.11.70.9.2.3.9.1.1 | ColumnswL2PortDropCounterPortIndex | read-only | current | This object indicates the module's port number.(1..Max port number in the module) |
| 1.3.6.1.4.1.171.11.70.9.2.3.9.1.2 | ColumnswL2PortBufferFullDrops | read-only | current | The total number of packets discarded while buffer full. |
| 1.3.6.1.4.1.171.11.70.9.2.3.9.1.3 | ColumnswL2PortACLDrops | read-only | current | The total number of packets denied by ACLs. |
| 1.3.6.1.4.1.171.11.70.9.2.3.9.1.4 | ColumnswL2PortMulticastDrops | read-only | current | The total number of multicast packet that is discarded. |
| 1.3.6.1.4.1.171.11.70.9.2.3.9.1.5 | ColumnswL2PortVLANIngressDrops | read-only | current | The total number of packets discarded by VLAN ingress checking. |
| 1.3.6.1.4.1.171.11.70.9.2.3.10 | TableswL2PortStatisTable | not-accessible | current | A table that contains information for each port 1519-9216 counter. |
| 1.3.6.1.4.1.171.11.70.9.2.3.10.1 | RowswL2PortStatisEntry | not-accessible | current | A list of information for each port counter of the device. |
| 1.3.6.1.4.1.171.11.70.9.2.3.10.1.1 | ColumnswL2PortStatisPortIndex | read-only | current | This object indicates the module's port number.(1..Max port number in the module) |
| 1.3.6.1.4.1.171.11.70.9.2.3.10.1.2 | ColumnswL2PortStatisPkts1519to1522Octets | read-only | current | The total number of packets length 1519-1522. |
| 1.3.6.1.4.1.171.11.70.9.2.3.10.1.3 | ColumnswL2PortStatisPkts1519to2047Octets | read-only | current | The total number of packets length 1519-1522. |
| 1.3.6.1.4.1.171.11.70.9.2.3.10.1.4 | ColumnswL2PortStatisPkts2048to4095Octets | read-only | current | The total number of packets length 2048-4095. |
| 1.3.6.1.4.1.171.11.70.9.2.3.10.1.5 | ColumnswL2PortStatisPkts4096to9216Octets | read-only | current | The total number of packets length 4096-9216. |
| 1.3.6.1.4.1.171.11.70.9.2.3.11 | TableswL2PortSfpInfoTable | not-accessible | current | A table that contains information for each sfp pluged in port. |
| 1.3.6.1.4.1.171.11.70.9.2.3.11.1 | RowswL2PortSfpInfoEntry | not-accessible | current | A list of information for each sfp pluged in port. |
| 1.3.6.1.4.1.171.11.70.9.2.3.11.1.1 | ColumnswL2PortSfpInfoPortIndex | read-only | current | This object indicates the module's port number.(1..Max port number in the module) |
| 1.3.6.1.4.1.171.11.70.9.2.3.11.1.2 | ColumnswL2PortSfpInfoConnectType | read-only | current | The ConnectType of sfp informaiton. |
| 1.3.6.1.4.1.171.11.70.9.2.3.11.1.3 | ColumnswL2PortSfpInfoVendorName | read-only | current | The vendor name of sfp informaiton. |
| 1.3.6.1.4.1.171.11.70.9.2.3.11.1.4 | ColumnswL2PortSfpInfoVendorPN | read-only | current | The vendor PN of sfp informaiton. |
| 1.3.6.1.4.1.171.11.70.9.2.3.11.1.5 | ColumnswL2PortSfpInfoVendorSN | read-only | current | The vendor SN of sfp informaiton. |
| 1.3.6.1.4.1.171.11.70.9.2.3.11.1.6 | ColumnswL2PortSfpInfoVendorOUI | read-only | current | The vendor OUI of sfp information. |
| 1.3.6.1.4.1.171.11.70.9.2.3.11.1.7 | ColumnswL2PortSfpInfoVendorRev | read-only | current | The vendor Rev of sfp information. |
| 1.3.6.1.4.1.171.11.70.9.2.3.11.1.8 | ColumnswL2PortSfpInfoDateCode | read-only | current | The date code of sfp information. |
| 1.3.6.1.4.1.171.11.70.9.2.3.11.1.9 | ColumnswL2PortSfpInfoFiberType | read-only | current | The fiber type of sfp information. |
| 1.3.6.1.4.1.171.11.70.9.2.3.11.1.10 | ColumnswL2PortSfpInfoBaudRate | read-only | current | The baud rate of sfp information. |
| 1.3.6.1.4.1.171.11.70.9.2.3.11.1.11 | ColumnswL2PortSfpInfoWavelength | read-only | current | The wavelength of sfp information. |
| 1.3.6.1.4.1.171.11.70.9.2.6 | NodeswL2QOSMgmt | |||
| 1.3.6.1.4.1.171.11.70.9.2.6.1 | TableswL2QOSBandwidthControlTable | not-accessible | current | . |
| 1.3.6.1.4.1.171.11.70.9.2.6.1.1 | RowswL2QOSBandwidthControlEntry | not-accessible | current | A list of information contained in swL2QOSBandwidthControlTable. |
| 1.3.6.1.4.1.171.11.70.9.2.6.1.1.1 | ColumnswL2QOSBandwidthPortIndex | read-only | current | Indicates the port . |
| 1.3.6.1.4.1.171.11.70.9.2.6.1.1.2 | ColumnswL2QOSBandwidthRxRate | read-write | current | Indicates RX Rate(1kbit/sec) of the specifed port. Value 10000000 means no limit. |
| 1.3.6.1.4.1.171.11.70.9.2.6.1.1.3 | ColumnswL2QOSBandwidthTxRate | read-write | current | Indicates TX Rate(1kbit/sec) of the specifed port. Value 10000000 means no limit. |
| 1.3.6.1.4.1.171.11.70.9.2.6.1.1.4 | ColumnswL2QOSBandwidthRadiusRxRate | read-only | current | The Rx Rate value comes from the RADIUS server, If an 802.1X port is authenticated, this value will overwrite the locally configured Rx Rate. |
| 1.3.6.1.4.1.171.11.70.9.2.6.1.1.5 | ColumnswL2QOSBandwidthRadiusTxRate | read-only | current | The Tx Rate value comes from the RADIUS server, If an 802.1X port is authenticated, this value will overwrite the locally configured Tx Rate. |
| 1.3.6.1.4.1.171.11.70.9.2.6.2 | TableswL2QOSSchedulingTable | not-accessible | current | . |
| 1.3.6.1.4.1.171.11.70.9.2.6.2.1 | RowswL2QOSSchedulingEntry | not-accessible | current | A list of information contained in swL2QOSSchedulingTable. |
| 1.3.6.1.4.1.171.11.70.9.2.6.2.1.1 | ColumnswL2QOSSchedulingPort | read-only | current | Indicates the port number. |
| 1.3.6.1.4.1.171.11.70.9.2.6.2.1.2 | ColumnswL2QOSSchedulingClassID | read-only | current | Indicates the hardware queue number. |
| 1.3.6.1.4.1.171.11.70.9.2.6.2.1.3 | ColumnswL2QOSSchedulingMaxPkts | read-write | current | Indicates the maximum number of packets the hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its … |
| 1.3.6.1.4.1.171.11.70.9.2.6.2.1.4 | ColumnswL2QOSSchedulingMechanism | read-write | current | Indicates the mechanism of QOS scheduling. |
| 1.3.6.1.4.1.171.11.70.9.2.6.2.1.5 | ColumnswL2QOSSchedulingMechanismEffec | read-only | current | Indicates the effective mechanism of QoS scheduling. If the swQoSSchedulingWeight is configured to be 0, then this object will always display strict (1). |
| 1.3.6.1.4.1.171.11.70.9.2.6.3 | TableswL2QOS8021pUserPriorityTable | not-accessible | current | . |
| 1.3.6.1.4.1.171.11.70.9.2.6.3.1 | RowswL2QOS8021pUserPriorityEntry | not-accessible | current | A list of information contained in swL2QOS8021pUserPriorityTable. |
| 1.3.6.1.4.1.171.11.70.9.2.6.3.1.1 | ColumnswL2QOS8021pUserPriorityIndex | read-only | current | The 802.1p user priority . |
| 1.3.6.1.4.1.171.11.70.9.2.6.3.1.2 | ColumnswL2QOS8021pUserPriorityClass | read-write | current | The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) a… |
| 1.3.6.1.4.1.171.11.70.9.2.6.4 | TableswL2QOS8021pDefaultPriorityTable | not-accessible | current | . |
| 1.3.6.1.4.1.171.11.70.9.2.6.4.1 | RowswL2QOS8021pDefaultPriorityEntry | not-accessible | current | A list of information contained in swL2QOS8021pDefaultPriorityTable. |
| 1.3.6.1.4.1.171.11.70.9.2.6.4.1.1 | ColumnswL2QOS8021pDefaultPriorityIndex | read-only | current | Indicates the port number . |
| 1.3.6.1.4.1.171.11.70.9.2.6.4.1.2 | ColumnswL2QOS8021pDefaultPriority | read-write | current | The priority value to assign to untagged packets received by the switch ports on the switch.. |
| 1.3.6.1.4.1.171.11.70.9.2.6.4.1.3 | ColumnswL2QOS8021pRadiusPriority | read-only | current | Indicates the value of 802.1p comes from RADIUS server. If an 802.1X port is authenticated, this value will overwrite the local configured value. |
| 1.3.6.1.4.1.171.11.70.9.2.6.5 | ScalarswL2QOSSchedulingMechanismCtrl | read-write | current | This object can control QOS scheduling Mechanism. |
| 1.3.6.1.4.1.171.11.70.9.2.6.6 | ScalarswL2QOSHolPreventionCtrl | read-write | current | Control QOS Hol Prevention |
| 1.3.6.1.4.1.171.11.70.9.2.6.7 | TableswCosBandwidthControlTable | not-accessible | current | A table that contains information about CoS Bandwidth Control on each port. |
| 1.3.6.1.4.1.171.11.70.9.2.6.7.1 | RowswCosBandwidthControlEntry | not-accessible | current | A list that contains CoS Bandwidth Control information for each port. |
| 1.3.6.1.4.1.171.11.70.9.2.6.7.1.1 | ColumnswCosBandwidthPort | read-only | current | This object indicates the port number. |
| 1.3.6.1.4.1.171.11.70.9.2.6.7.1.2 | ColumnswCosBandwidthClassID | read-only | current | Indicates the hardware queue number. |
| 1.3.6.1.4.1.171.11.70.9.2.6.7.1.3 | ColumnswCosBandwidthMinRate | read-write | current | Indicates the Minimum Rate of the specified port. A value of 0 means no limit. |
| 1.3.6.1.4.1.171.11.70.9.2.6.7.1.4 | ColumnswCosBandwidthMaxRate | read-write | current | Indicates the Maximum Rate of the specified port. A value of 0 means no limit. |
| 1.3.6.1.4.1.171.11.70.9.2.6.8 | TableswCpuRxRateControlTable | not-accessible | current | A table that contains information about CPU receiving rate control. |
| 1.3.6.1.4.1.171.11.70.9.2.6.8.1 | RowswCpuRxRateControlEntry | not-accessible | current | A list that contains CPU CoS receiving rate control information. |
| 1.3.6.1.4.1.171.11.70.9.2.6.8.1.1 | ColumnswCpuRxClassID | not-accessible | current | Indicates the Class of Service ID. |
| 1.3.6.1.4.1.171.11.70.9.2.6.8.1.2 | ColumnswCpuRxRateControlStatus | read-write | current | Indicates the status of receiving rate control. |
| 1.3.6.1.4.1.171.11.70.9.2.6.9 | TableswQosDscpTrustPortCtrlTable | not-accessible | current | A table that contains information about the DSCP trust portlist. |
| 1.3.6.1.4.1.171.11.70.9.2.6.9.1 | RowswQosDscpTrustPortCtrlEntry | not-accessible | current | A list that contains the DSCP trusted state per port. |
| 1.3.6.1.4.1.171.11.70.9.2.6.9.1.1 | ColumnswQosDscpTrustPortCtrlPortIndex | read-only | current | This object indicates the port number. |
| 1.3.6.1.4.1.171.11.70.9.2.6.9.1.2 | ColumnswQosDscpTrustPortCtrlState | read-write | current | This object is used to enable/disable the DSCP trusted state on a selected port. |
| 1.3.6.1.4.1.171.11.70.9.2.6.10 | TableswQosDscpMapGlobalCtrlTable | not-accessible | current | A table that contains information about DSCP map to priority and packet color on each port. |
| 1.3.6.1.4.1.171.11.70.9.2.6.10.1 | RowswQosDscpMapGlobalCtrlEntry | not-accessible | current | A list that contains DSCP map information for each port. |
| 1.3.6.1.4.1.171.11.70.9.2.6.10.1.1 | ColumnswQosDscpMapGlobalCtrlDscpIndex | read-only | current | This object indicates the source DSCP incoming packet. |
| 1.3.6.1.4.1.171.11.70.9.2.6.10.1.2 | ColumnswQosDscpMapGlobalCtrl8021pPriority | read-write | current | This object indicates the 802.1p priority on each port. Default value is: DSCP Priority 0-7 0 8-15 1 16-23 2 24-31 3 32-39 4 40-47 5 48-55 6 56-63 7 |
| 1.3.6.1.4.1.171.11.70.9.2.6.10.1.3 | ColumnswQosDscpMapGlobalCtrlNewDscp | read-write | current | This object indicates the new DSCP map on each port. |
| 1.3.6.1.4.1.171.11.70.9.2.7 | NodeswL2PortSecurityMgmt | |||
| 1.3.6.1.4.1.171.11.70.9.2.7.1 | TableswL2PortSecurityControlTable | not-accessible | current | port security feature which controls the address leaning capability and the traffic forwarding decision. Each port can have this function enabled or disabled. … |
| 1.3.6.1.4.1.171.11.70.9.2.7.1.1 | RowswL2PortSecurityControlEntry | not-accessible | current | A list of information contained in swL2PortSecurityControlTable. |
| 1.3.6.1.4.1.171.11.70.9.2.7.1.1.1 | ColumnswL2PortSecurityPortIndex | read-only | current | Indicates the secured port to lock address learning. |
| 1.3.6.1.4.1.171.11.70.9.2.7.1.1.2 | ColumnswL2PortSecurityMaxLernAddr | read-write | current | Indicates allowable number of addresses to be learned at this port. |
| 1.3.6.1.4.1.171.11.70.9.2.7.1.1.3 | ColumnswL2PortSecurityMode | read-write | current | Indicates the mode of locking address. In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer expire. In this mode, when the locke… |
| 1.3.6.1.4.1.171.11.70.9.2.7.1.1.4 | ColumnswL2PortSecurityAdmState | read-write | current | Indicates administration state of locking address. |
| 1.3.6.1.4.1.171.11.70.9.2.7.2 | NodeswL2PortSecurityDelCtrl | |||
| 1.3.6.1.4.1.171.11.70.9.2.7.2.1 | ScalarswL2PortSecurityDelVlanName | read-write | current | Indicates vlan name. |
| 1.3.6.1.4.1.171.11.70.9.2.7.2.2 | ScalarswL2PortSecurityDelPort | read-write | current | Indicates the port.0 indicated the function isn't working now. |
| 1.3.6.1.4.1.171.11.70.9.2.7.2.3 | ScalarswL2PortSecurityDelMacAddress | read-write | current | Specifies MAC address. |
| 1.3.6.1.4.1.171.11.70.9.2.7.2.4 | ScalarswL2PortSecurityDelActivity | read-write | current | . |
| 1.3.6.1.4.1.171.11.70.9.2.9 | NodeswL2TrunkMgmt | |||
| 1.3.6.1.4.1.171.11.70.9.2.9.1 | ScalarswL2TrunkMaxSupportedEntries | read-only | current | Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable). |
| 1.3.6.1.4.1.171.11.70.9.2.9.2 | ScalarswL2TrunkCurrentNumEntries | read-only | current | Current actived number of entries in the trunk configuration table. |
| 1.3.6.1.4.1.171.11.70.9.2.9.3 | TableswL2TrunkCtrlTable | not-accessible | current | This table specifys which ports group a set of ports(up to 8) into a single logical link. |
| 1.3.6.1.4.1.171.11.70.9.2.9.3.1 | RowswL2TrunkCtrlEntry | not-accessible | current | A list of information specifies which ports group a set of ports(up to 8) into a single logical link. |
| 1.3.6.1.4.1.171.11.70.9.2.9.3.1.1 | ColumnswL2TrunkIndex | read-only | current | The index of logical port trunk. The trunk group number depend on the existence of unit and module. |
| 1.3.6.1.4.1.171.11.70.9.2.9.3.1.3 | ColumnswL2TrunkMasterPort | read-create | current | The object indicates the master port number of the port trunk entry. When using Port Trunk, you can not configure the other ports of the group except the maste… |
| 1.3.6.1.4.1.171.11.70.9.2.9.3.1.4 | ColumnswL2TrunkMember | read-create | current | Indicate how many number of ports is included in this Trunk. The trunk port number depend on the existence of module. The maximum number of ports is 8 for one … |
| 1.3.6.1.4.1.171.11.70.9.2.9.3.1.5 | ColumnswL2TrunkFloodingPort | read-only | current | The object indicates the flooding port number of the port trunk entry. The first port of the trunk is implicitly configured to be the flooding port. |
| 1.3.6.1.4.1.171.11.70.9.2.9.3.1.6 | ColumnswL2TrunkType | read-create | current | This object indicated that type of the trunk group. static : is static trunk group lacp : is LACP trunk group . |
| 1.3.6.1.4.1.171.11.70.9.2.9.3.1.7 | ColumnswL2TrunkState | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.11.70.9.2.9.3.1.8 | ColumnswL2TrunkActivePorts | read-only | current | The object indicates the active ports of the port trunk entry. |
| 1.3.6.1.4.1.171.11.70.9.2.9.4 | ScalarswL2TrunkAlgorithm | read-write | current | This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data. |
| 1.3.6.1.4.1.171.11.70.9.2.9.5 | TableswL2TrunkLACPPortTable | not-accessible | current | This table specifys which ports group a set of ports(up to 8) into a single logical link. |
| 1.3.6.1.4.1.171.11.70.9.2.9.5.1 | RowswL2TrunkLACPPortEntry | not-accessible | current | A list of information specifies which ports group a set of ports(up to 8) into a single logical link. |
| 1.3.6.1.4.1.171.11.70.9.2.9.5.1.1 | ColumnswL2TrunkLACPPortIndex | read-only | current | The index of logical port lacp. |
| 1.3.6.1.4.1.171.11.70.9.2.9.5.1.2 | ColumnswL2TrunkLACPPortState | read-write | current | The state of logical port lacp. |
| 1.3.6.1.4.1.171.11.70.9.2.9.6 | TableswL2TrunkVLANTable | not-accessible | current | This table is used to manage the VLAN trunking feature of the device. |
| 1.3.6.1.4.1.171.11.70.9.2.9.6.1 | RowswL2TrunkVLANEntry | not-accessible | current | This object is used to configure the VLAN trunking settings for each port. |
| 1.3.6.1.4.1.171.11.70.9.2.9.6.1.1 | ColumnswL2TrunkVLANPort | read-only | current | This object indicates the port being configured. |
| 1.3.6.1.4.1.171.11.70.9.2.9.6.1.2 | ColumnswL2TrunkVLANState | read-write | current | The state of the logical port LACP. |
| 1.3.6.1.4.1.171.11.70.9.2.10 | NodeswL2MirrorMgmt | |||
| 1.3.6.1.4.1.171.11.70.9.2.10.1 | ScalarswL2MirrorLogicTargetPort | read-write | current | This object indicates switch which port will sniff another port. A trunk port member cannot be configured as a target Snooping port. The port number is the seq… |
| 1.3.6.1.4.1.171.11.70.9.2.10.2 | ScalarswL2MirrorPortSourceIngress | read-write | current | The represent the ingress into the source port packet to sniffed. |
| 1.3.6.1.4.1.171.11.70.9.2.10.3 | ScalarswL2MirrorPortSourceEgress | read-write | current | The represent the egress from the source port packet to sniffed. |
| 1.3.6.1.4.1.171.11.70.9.2.10.4 | ScalarswL2MirrorPortState | read-write | current | This object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from e… |
| 1.3.6.1.4.1.171.11.70.9.2.10.5 | TableswL2MirrorGroupTable | not-accessible | current | This table specifies information about the Mirror group configuration. |
| 1.3.6.1.4.1.171.11.70.9.2.10.5.1 | RowswL2MirrorGroupEntry | not-accessible | current | A list of information about each Mirror group configuration. |
| 1.3.6.1.4.1.171.11.70.9.2.10.5.1.1 | ColumnswL2MirrorGroupID | not-accessible | current | This object indicates the mirror group. The range of this object is (1..n), the value of n depends on detail project. |
| 1.3.6.1.4.1.171.11.70.9.2.10.5.1.2 | ColumnswL2MirrorGroupRowStatus | read-create | current | This object manages this mirror group entry. |
| 1.3.6.1.4.1.171.11.70.9.2.10.5.1.3 | ColumnswL2MirrorGroupState | read-create | current | This object indicates the mirror group state. |
| 1.3.6.1.4.1.171.11.70.9.2.10.5.1.4 | ColumnswL2MirrorGroupLogicTargetPort | read-create | current | This object indicates the mirror group target port. |
| 1.3.6.1.4.1.171.11.70.9.2.10.5.1.5 | ColumnswL2MirrorGroupPortSourceIngress | read-create | current | This object indicates the mirror group ingress source ports. |
| 1.3.6.1.4.1.171.11.70.9.2.10.5.1.6 | ColumnswL2MirrorGroupPortSourceEngress | read-create | current | This object indicates the mirror group engress source ports. |
| 1.3.6.1.4.1.171.11.70.9.2.11 | NodeswL2IGMPMgmt | |||
| 1.3.6.1.4.1.171.11.70.9.2.11.1 | ScalarswL2IGMPMaxSupportedVlans | read-only | current | Maximum number of Vlans in the layer 2 IGMP control table (swL2IGMPCtrlTable). |
| 1.3.6.1.4.1.171.11.70.9.2.11.2 | ScalarswL2IGMPMaxIpGroupNumPerVlan | read-only | current | Maximum number of multicast ip group per Vlan in the layer 2 IGMP information table (swL2IGMPQueryInfoTable). |
| 1.3.6.1.4.1.171.11.70.9.2.11.3 | TableswL2IGMPCtrlTable | not-accessible | current | The table controls the Vlan's IGMP function. Its scale depends on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled mode, there is only one entry in… |
| 1.3.6.1.4.1.171.11.70.9.2.11.3.1 | RowswL2IGMPCtrlEntry | not-accessible | current | The entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled. |
| 1.3.6.1.4.1.171.11.70.9.2.11.3.1.1 | ColumnswL2IGMPCtrlVid | read-only | current | This object indicates the IGMP control entry's VLAN id. If VLAN is disabled, the Vid is always 0 and cannot be changed by management users. If VLAN is in Port-… |
| 1.3.6.1.4.1.171.11.70.9.2.11.3.1.2 | ColumnswL2IGMPQueryInterval | read-write | current | The frequency at which IGMP Host-Query packets are transmitted on this switch. |
| 1.3.6.1.4.1.171.11.70.9.2.11.3.1.3 | ColumnswL2IGMPMaxResponseTime | read-write | current | The maximum query response time on this switch. |
| 1.3.6.1.4.1.171.11.70.9.2.11.3.1.4 | ColumnswL2IGMPRobustness | read-write | current | The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. … |
| 1.3.6.1.4.1.171.11.70.9.2.11.3.1.5 | ColumnswL2IGMPLastMemberQueryInterval | read-write | current | The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount o… |
| 1.3.6.1.4.1.171.11.70.9.2.11.3.1.6 | ColumnswL2IGMPHostTimeout | read-write | current | The timer value for sending IGMP query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to sen… |
| 1.3.6.1.4.1.171.11.70.9.2.11.3.1.7 | ColumnswL2IGMPRouteTimeout | read-write | current | The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages. |
| 1.3.6.1.4.1.171.11.70.9.2.11.3.1.8 | ColumnswL2IGMPLeaveTimer | read-write | current | When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeav… |
| 1.3.6.1.4.1.171.11.70.9.2.11.3.1.9 | ColumnswL2IGMPQueryState | read-write | current | This object decide the IGMP query enabled or disabled. |
| 1.3.6.1.4.1.171.11.70.9.2.11.3.1.10 | ColumnswL2IGMPCurrentState | read-only | current | This object indicates the current IGMP query state. |
| 1.3.6.1.4.1.171.11.70.9.2.11.3.1.11 | ColumnswL2IGMPCtrlState | read-write | current | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from e… |
| 1.3.6.1.4.1.171.11.70.9.2.11.3.1.12 | ColumnswL2IGMPFastLeaveState | read-write | current | This object indicates the fast_leave status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are diffe… |
| 1.3.6.1.4.1.171.11.70.9.2.11.3.1.13 | ColumnswL2IGMPQueryVersion | read-write | current | Configure the IGMP version of query packet which will be sent by the router. |
| 1.3.6.1.4.1.171.11.70.9.2.11.3.1.15 | ColumnswL2IGMPReportSuppression | read-write | current | When enabled, multiple IGMP reports or leaves for a specific group (S,G) will be integrated into only one report before being sent to the router port. |
| 1.3.6.1.4.1.171.11.70.9.2.11.4 | TableswL2IGMPQueryInfoTable | not-accessible | current | The table contains the number current IGMP query packets which is captured by this device, as well as the IGMP query packets sent by the device. |
| 1.3.6.1.4.1.171.11.70.9.2.11.4.1 | RowswL2IGMPQueryInfoEntry | not-accessible | current | Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN entry are all enabled. |
| 1.3.6.1.4.1.171.11.70.9.2.11.4.1.1 | ColumnswL2IGMPInfoVid | read-only | current | This object indicates the Vid of associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable). |
| 1.3.6.1.4.1.171.11.70.9.2.11.4.1.2 | ColumnswL2IGMPInfoQueryCount | read-only | current | This object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis. |
| 1.3.6.1.4.1.171.11.70.9.2.11.4.1.3 | ColumnswL2IGMPInfoTxQueryCount | read-only | current | This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to relate… |
| 1.3.6.1.4.1.171.11.70.9.2.11.5 | TableswL2IGMPInfoTable | not-accessible | current | The table containing current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN ent… |
| 1.3.6.1.4.1.171.11.70.9.2.11.5.1 | RowswL2IGMPInfoEntry | not-accessible | current | Information about current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry … |
| 1.3.6.1.4.1.171.11.70.9.2.11.5.1.1 | ColumnswL2IGMPVid | read-only | current | This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network. |
| 1.3.6.1.4.1.171.11.70.9.2.11.5.1.2 | ColumnswL2IGMPGroupIpAddr | read-only | current | This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis. |
| 1.3.6.1.4.1.171.11.70.9.2.11.5.1.3 | ColumnswL2IGMPMacAddr | read-only | current | This object is identify mac address which is corresponding to swL2IGMPGroupIpAddr, in per-Vlan basis. |
| 1.3.6.1.4.1.171.11.70.9.2.11.5.1.4 | ColumnswL2IGMPPortMap | read-only | current | This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map… |
| 1.3.6.1.4.1.171.11.70.9.2.11.5.1.5 | ColumnswL2IGMPIpGroupReportCount | read-only | current | This object indicate how much report packet was receive by our device corresponding with this entry from IGMP function enabled, in per-Vlan basis. |
| 1.3.6.1.4.1.171.11.70.9.2.11.6 | TableswL2IGMPRouterPortsTable | not-accessible | current | The table controls the Vlan's IGMP router ports function. |
| 1.3.6.1.4.1.171.11.70.9.2.11.6.1 | RowswL2IGMPRouterPortsEntry | not-accessible | current | The entry in IGMP router ports table (swL2IGMPRouterPortsTable). |
| 1.3.6.1.4.1.171.11.70.9.2.11.6.1.1 | ColumnswL2IGMPRouterPortsVid | read-only | current | This object indicates the IGMP router ports entry's VLAN id. If VLAN is disabled, the Vid is always 0 and cannot be changed by management users. If VLAN is in … |
| 1.3.6.1.4.1.171.11.70.9.2.11.6.1.2 | ColumnswL2IGMPRouterStaticPortList | read-write | current | |
| 1.3.6.1.4.1.171.11.70.9.2.11.6.1.3 | ColumnswL2IGMPRouterDynamicPortList | read-only | current | |
| 1.3.6.1.4.1.171.11.70.9.2.11.6.1.4 | ColumnswL2IGMPRouterForbiddenPortList | read-write | current | |
| 1.3.6.1.4.1.171.11.70.9.2.11.7 | TableswL2IGMPMulticastVlanTable | not-accessible | current | The information of the IGMP snooping multicast vlan table. |
| 1.3.6.1.4.1.171.11.70.9.2.11.7.1 | RowswL2IGMPMulticastVlanEntry | not-accessible | current | The entry of swL2IGMPMulticastVlanTable. |
| 1.3.6.1.4.1.171.11.70.9.2.11.7.1.1 | ColumnswL2IGMPMulticastVlanid | read-only | current | This object indicates the vlan id of the IGMP snooping multicast vlan entry. |
| 1.3.6.1.4.1.171.11.70.9.2.11.7.1.2 | ColumnswL2IGMPMulticastVlanName | read-create | current | This object indicates the vlan name of the IGMP snooping multicast vlan entry. |
| 1.3.6.1.4.1.171.11.70.9.2.11.7.1.3 | ColumnswL2IGMPMulticastVlanSourcePort | read-create | current | This object indicate the portlist of the source ports of IGMP snooping multicast vlan. The source ports will be set as tag ports of the vlan entry. And the IGM… |
| 1.3.6.1.4.1.171.11.70.9.2.11.7.1.4 | ColumnswL2IGMPMulticastVlanMemberPort | read-create | current | This object indicate the portlist of the member ports of IGMP snooping multicast vlan. The source ports will be set as untag ports of the vlan entry. And the I… |
| 1.3.6.1.4.1.171.11.70.9.2.11.7.1.5 | ColumnswL2IGMPMulticastVlanReplaceSourceIP | read-write | current | The replace source IP of this multicast vlan. |
| 1.3.6.1.4.1.171.11.70.9.2.11.7.1.6 | ColumnswL2IGMPMulticastVlanRangeName | read-write | current | The name of multicast address range. When read, it shows NULL. |
| 1.3.6.1.4.1.171.11.70.9.2.11.7.1.7 | ColumnswL2IGMPMulticastVlanRangeState | read-write | current | This object is uesed to add or delete the specified multicast address range. when read it shows none(1); when set add(2) or delete(3),the swL2IGMPMulticastVlan… |
| 1.3.6.1.4.1.171.11.70.9.2.11.7.1.8 | ColumnswL2IGMPMulticastVlanState | read-write | current | This object can be enabled or disabled IGMP_snooping multicast VLAN. |
| 1.3.6.1.4.1.171.11.70.9.2.11.7.1.9 | ColumnswL2IGMPMulticastVlanRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.11.70.9.2.11.7.1.10 | ColumnswL2IGMPMulticastVlanUntagSourcePort | read-write | current | This object indicates the untagged member ports to add to the multicast VLAN. |
| 1.3.6.1.4.1.171.11.70.9.2.11.7.1.11 | ColumnswL2IGMPMulticastVlanRemapPriority | read-create | current | The priority value (0 to 7) to be associated with the data traffic to be forwarded on the multicast VLAN. When set to 8, the packet's original priority will be… |
| 1.3.6.1.4.1.171.11.70.9.2.11.7.1.12 | ColumnswL2IGMPMulticastVlanReplacePriority | read-create | current | Specifies that a packet's priority will be changed by the switch based on the remap priority. This flag will only take effect when remap priority is set. |
| 1.3.6.1.4.1.171.11.70.9.2.11.7.1.13 | ColumnswL2IGMPMulticastVlanTagMemberPort | read-write | current | This object indicates the port list of the tag member ports of the IGMP snooping multicast VLAN. |
| 1.3.6.1.4.1.171.11.70.9.2.11.8 | TableswL2IGMPForwardingTable | not-accessible | current | The table containing current IGMP forwarding information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associat… |
| 1.3.6.1.4.1.171.11.70.9.2.11.8.1 | RowswL2IGMPForwardingEntry | not-accessible | current | Information about current IGMP forwarding information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated … |
| 1.3.6.1.4.1.171.11.70.9.2.11.8.1.1 | ColumnswL2IGMPForwardingVid | read-only | current | This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network. |
| 1.3.6.1.4.1.171.11.70.9.2.11.8.1.2 | ColumnswL2IGMPForwardingSrcIp | read-only | current | This object is identify source ip address. |
| 1.3.6.1.4.1.171.11.70.9.2.11.8.1.3 | ColumnswL2IGMPForwardingGroupAddr | read-only | current | This object is identify group ip address. |
| 1.3.6.1.4.1.171.11.70.9.2.11.8.1.4 | ColumnswL2IGMPForwardingPortMember | read-only | current | This object indicates which ports are belong to the same multicast group, in per-Vlan basis. |
| 1.3.6.1.4.1.171.11.70.9.2.11.9 | TableswL2IGMPMulticastVlanGroupTable | not-accessible | current | The table containing the IGMP snooping multicast VLAN group information |
| 1.3.6.1.4.1.171.11.70.9.2.11.9.1 | RowswL2IGMPMulticastVlanGroupEntry | not-accessible | current | Information about current IGMP snooping multicast VLAN group. |
| 1.3.6.1.4.1.171.11.70.9.2.11.9.1.1 | ColumnswL2IGMPMulticastVlanGroupVid | read-only | current | This object indicates the Vid of IGMP snooping multicast VLAN group. |
| 1.3.6.1.4.1.171.11.70.9.2.11.9.1.2 | ColumnswL2IGMPMulticastVlanGroupRangeName | read-only | current | The name of multicast address range. |
| 1.3.6.1.4.1.171.11.70.9.2.11.9.1.3 | ColumnswL2IGMPMulticastVlanGroupHead | read-only | current | The head of multicast address range. |
| 1.3.6.1.4.1.171.11.70.9.2.11.9.1.4 | ColumnswL2IGMPMulticastVlanGroupTail | read-only | current | The tail of multicast address range. |
| 1.3.6.1.4.1.171.11.70.9.2.11.11 | TableswIGMPSnoopingGroupTable | not-accessible | current | The table contains the current IGMP snooping group information captured by the device. |
| 1.3.6.1.4.1.171.11.70.9.2.11.11.1 | RowswIGMPSnoopingGroupEntry | not-accessible | current | Information about the current IGMP snooping group information which has been captured by the device. |
| 1.3.6.1.4.1.171.11.70.9.2.11.11.1.1 | ColumnswIGMPSnoopingGroupVid | read-only | current | This object indicates the VID of the individual IGMP snooping group table entry. |
| 1.3.6.1.4.1.171.11.70.9.2.11.11.1.2 | ColumnswIGMPSnoopingGroupGroupAddr | read-only | current | This object identifies the group IP address which have been captured from the IGMP packet, on a per-VLAN basis. |
| 1.3.6.1.4.1.171.11.70.9.2.11.11.1.3 | ColumnswIGMPSnoopingGroupSourceAddr | read-only | current | This object identifies the source addresses. |
| 1.3.6.1.4.1.171.11.70.9.2.11.11.1.4 | ColumnswIGMPSnoopingGroupIncludePortMap | read-only | current | This object indicates the port list under INCLUDE mode. |
| 1.3.6.1.4.1.171.11.70.9.2.11.11.1.5 | ColumnswIGMPSnoopingGroupExcludePortMap | read-only | current | This object indicates the port list under EXCLUDE mode. |
| 1.3.6.1.4.1.171.11.70.9.2.11.16 | TableswL2IGMPSnoopingStaticGroupTable | not-accessible | current | The table contains the current IGMP snooping static group information captured by the device. |
| 1.3.6.1.4.1.171.11.70.9.2.11.16.1 | RowswL2IGMPSnoopingStaticGroupEntry | not-accessible | current | Information about current IGMP snooping static group information captured by the device. |
| 1.3.6.1.4.1.171.11.70.9.2.11.16.1.1 | ColumnswL2IGMPSnoopingStaticGroupVID | read-only | current | This object indicates the VID of the current IGMP snooping static group. |
| 1.3.6.1.4.1.171.11.70.9.2.11.16.1.2 | ColumnswL2IGMPSnoopingStaticGroupIPaddress | read-only | current | This object indicates the current IGMP snooping static group IP address. |
| 1.3.6.1.4.1.171.11.70.9.2.11.16.1.3 | ColumnswL2IGMPSnoopingStaticGroupMemberPortList | read-write | current | This object indicates the current IGMP snooping static group Member Portlist. |
| 1.3.6.1.4.1.171.11.70.9.2.11.16.1.4 | ColumnswL2IGMPSnoopingStaticGroupRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.11.70.9.2.14 | NodeswL2TrafficSegMgmt | |||
| 1.3.6.1.4.1.171.11.70.9.2.14.1 | TableswL2TrafficSegTable | not-accessible | current | This table specifys the port just can forward traffic to the specific port list. |
| 1.3.6.1.4.1.171.11.70.9.2.14.1.1 | RowswL2TrafficSegEntry | not-accessible | current | A list of information specifies the port with its traffic forward list. |
| 1.3.6.1.4.1.171.11.70.9.2.14.1.1.1 | ColumnswL2TrafficSegPort | read-only | current | The port number of the logical port. |
| 1.3.6.1.4.1.171.11.70.9.2.14.1.1.2 | ColumnswL2TrafficSegForwardPorts | read-write | current | The port list that the specific port can forward traffic. |
| 1.3.6.1.4.1.171.11.70.9.2.15 | NodeswL2IpLimitedMulticastMgmt | |||
| 1.3.6.1.4.1.171.11.70.9.2.15.1 | TableswL2IpLimitedMulticastTable | not-accessible | current | This entity's per-port Limited IP multicast address range table. |
| 1.3.6.1.4.1.171.11.70.9.2.15.1.1 | RowswL2IpLimitedMulticastEntry | not-accessible | current | A particular route to a particular destination, under a particular policy. Once an entry be built,it shouldn't be modified.That is,it just support create and d… |
| 1.3.6.1.4.1.171.11.70.9.2.15.1.1.1 | ColumnswL2IpLimitedMulticastPortIndex | read-only | current | A port to config the limited multicast address. |
| 1.3.6.1.4.1.171.11.70.9.2.15.1.1.2 | ColumnswL2IpLimitedMulticastHead | not-accessible | obsolete | The head of multicast address range. |
| 1.3.6.1.4.1.171.11.70.9.2.15.1.1.3 | ColumnswL2IpLimitedMulticastTail | not-accessible | obsolete | The tail of multicast address range. |
| 1.3.6.1.4.1.171.11.70.9.2.15.1.1.4 | ColumnswL2IpLimitedMulticastAccess | read-write | current | It allow you to permit or deny multicast range. |
| 1.3.6.1.4.1.171.11.70.9.2.15.1.1.5 | ColumnswL2IpLimitedMulticastState | read-write | current | Enable or disable limited multicast address for the chosen port. |
| 1.3.6.1.4.1.171.11.70.9.2.15.1.1.6 | ColumnswL2IpLimitedMulticastDelState | not-accessible | obsolete | Enable or disable delete limited multicast address for the chosen port. |
| 1.3.6.1.4.1.171.11.70.9.2.15.1.1.7 | ColumnswL2IpLimitedMulticastRangeName | read-write | current | The name of multicast address range. When read, it shows NULL. |
| 1.3.6.1.4.1.171.11.70.9.2.15.1.1.8 | ColumnswL2IpLimitedMulticastRangeNameState | read-write | current | Add or delete the specified multicast address range. When read, it shows other(1); When set add(2) or delete(3), the swL2IpLimitedMulticastRangeName should be … |
| 1.3.6.1.4.1.171.11.70.9.2.15.2 | TableswL2LimitedMulticastAddressTable | not-accessible | current | A table contains the limited multicast address information. |
| 1.3.6.1.4.1.171.11.70.9.2.15.2.1 | RowswL2LimitedMulticastAddressEntry | not-accessible | current | The information of limited multicast address. |
| 1.3.6.1.4.1.171.11.70.9.2.15.2.1.1 | ColumnswL2LimitedMulticastAddressPort | read-only | current | The port index. |
| 1.3.6.1.4.1.171.11.70.9.2.15.2.1.2 | ColumnswL2LimitedMulticastAddressRangeName | read-only | current | The name of multicast address range. |
| 1.3.6.1.4.1.171.11.70.9.2.15.2.1.3 | ColumnswL2LimitedMulticastAddressHead | read-only | current | The head of multicast address range. |
| 1.3.6.1.4.1.171.11.70.9.2.15.2.1.4 | ColumnswL2LimitedMulticastAddressTail | read-only | current | The tail of multicast address range. |
| 1.3.6.1.4.1.171.11.70.9.2.16 | NodeswL2MgmtMIBTraps | |||
| 1.3.6.1.4.1.171.11.70.9.2.16.1 | NodeswL2Notify | |||
| 1.3.6.1.4.1.171.11.70.9.2.16.1.2 | NodeswL2NotifyPrefix | |||
| 1.3.6.1.4.1.171.11.70.9.2.16.1.2.0 | NodeswL2NotifFirmware | |||
| 1.3.6.1.4.1.171.11.70.9.2.16.1.2.0.1 | NotificationswL2macNotification | current | This trap indicates the mac addresses variation in address table . | |
| 1.3.6.1.4.1.171.11.70.9.2.16.1.2.0.3 | NotificationswL2PortLoopOccurred | current | The trap is sent when Port loop occurred. | |
| 1.3.6.1.4.1.171.11.70.9.2.16.1.2.0.4 | NotificationswL2PortLoopRestart | current | The trap is sent when Port loop restart after interval time. | |
| 1.3.6.1.4.1.171.11.70.9.2.16.1.2.0.5 | NotificationswL2VlanLoopOccurred | current | The trap is sent when Port with VID loop occurred. | |
| 1.3.6.1.4.1.171.11.70.9.2.16.1.2.0.6 | NotificationswL2VlanLoopRestart | current | The trap is sent when Port with VID loop restart after interval time. | |
| 1.3.6.1.4.1.171.11.70.9.2.16.1.2.1 | Nodeswl2NotificationBidings | |||
| 1.3.6.1.4.1.171.11.70.9.2.16.1.2.1.1 | ScalarswL2macNotifyInfo | read-only | current | This object indicates the last time reboot information. |
| 1.3.6.1.4.1.171.11.70.9.2.16.1.2.1.3 | ScalarswL2VlanLoopDetectVID | accessible-for-notify | current | This object indicates the VID that has detected a loopback. |
| 1.3.6.1.4.1.171.11.70.9.2.17 | NodeswL2VlanMgmt | |||
| 1.3.6.1.4.1.171.11.70.9.2.17.1 | TableswL2VlanTable | not-accessible | current | A table containing current configuration information for each VLAN currently configured into the device by (local or network) management, or dynamically create… |
| 1.3.6.1.4.1.171.11.70.9.2.17.1.1 | RowswL2VlanEntry | not-accessible | current | Information for a VLAN configured into the device by (local or network) management, or dynamically created as a result of GVRP requests received. |
| 1.3.6.1.4.1.171.11.70.9.2.17.1.1.1 | ColumnswL2VlanIndex | not-accessible | current | The VLAN ID of the VLAN to be created. The range is 1 - 4094. |
| 1.3.6.1.4.1.171.11.70.9.2.17.1.1.2 | ColumnswL2VlanName | read-only | current | The name of the VLAN to be displayed. |
| 1.3.6.1.4.1.171.11.70.9.2.17.1.1.3 | ColumnswL2VlanType | read-only | current | The type of the VLAN to be displayed. |
| 1.3.6.1.4.1.171.11.70.9.2.17.1.1.4 | ColumnswL2VlanMemberPorts | read-only | current | A range of member ports to the VLAN. |
| 1.3.6.1.4.1.171.11.70.9.2.17.1.1.5 | ColumnswL2VlanStaticPorts | read-only | current | A range of static ports to the VLAN. |
| 1.3.6.1.4.1.171.11.70.9.2.17.1.1.6 | ColumnswL2VlanStaticTaggedPorts | read-only | current | Specifies the additional ports as tagged. |
| 1.3.6.1.4.1.171.11.70.9.2.17.1.1.7 | ColumnswL2VlanStaticUntaggedPorts | read-only | current | Specifies the additional ports as untagged. |
| 1.3.6.1.4.1.171.11.70.9.2.17.1.1.8 | ColumnswL2VlanForbiddenPorts | read-only | current | The set of ports which are prohibited by management from being included in the egress list for this VLAN. Changes to this object that cause a port to be includ… |
| 1.3.6.1.4.1.171.11.70.9.2.17.1.1.9 | ColumnswL2VlanCurrentTaggedPorts | read-only | current | The set of ports which are transmitting traffic for this VLAN as tagged frames. |
| 1.3.6.1.4.1.171.11.70.9.2.17.1.1.10 | ColumnswL2VlanCurrentUntaggedPorts | read-only | current | The set of ports which are transmitting traffic for this VLAN as untagged frames. |
| 1.3.6.1.4.1.171.11.70.9.2.17.1.1.11 | ColumnswL2VlanAdvertisementState | read-write | current | Specifies the VLAN as able to join GVRP If this parameter is not set, the VLAN cannot be configured to have forbidden ports. This flag protocol VLAN is fixed t… |
| 1.3.6.1.4.1.171.11.70.9.2.17.2 | ScalarswL2PVIDAutoAssignmentState | read-write | current | This object controls the PVID auto assigment state. If 'Auto-assign PVID' is disabled, PVID only be changed by PVID configuration (user changes explicitly). Th… |
| 1.3.6.1.4.1.171.11.70.9.2.18 | NodeswL2dot1vProtocolMgmt | |||
| 1.3.6.1.4.1.171.11.70.9.2.18.1 | TableswL2dot1vProtocolGroupTable | not-accessible | current | A table that contains mappings from Protocol Templates to Protocol Group Identifiers used for Port-and-Protocol-based VLAN Classification. |
| 1.3.6.1.4.1.171.11.70.9.2.18.1.1 | RowswL2dot1vProtocolGroupEntry | not-accessible | current | A mapping from a Protocol Template to a Protocol Group Identifier. |
| 1.3.6.1.4.1.171.11.70.9.2.18.1.1.1 | ColumnswL2dot1vProtocolTemplateFrameType | read-only | current | The data-link encapsulation format or the 'detagged_frame_type' in a Protocol Template. |
| 1.3.6.1.4.1.171.11.70.9.2.18.1.1.2 | ColumnswL2dot1vProtocolTemplateProtocolValue | read-only | current | The identification of the protocol above the data-link layer in a Protocol Template. Depending on the frame type, the octet string will have one of the followi… |
| 1.3.6.1.4.1.171.11.70.9.2.18.1.1.3 | ColumnswL2dot1vProtocolGroupId | read-create | current | Represents a group of protocols that are associated together when assigning a VID to a frame. |
| 1.3.6.1.4.1.171.11.70.9.2.18.1.1.4 | ColumnswL2dot1vProtocolGroupRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.11.70.9.2.18.2 | TableswL2dot1vProtocolPortTable | not-accessible | current | A table that contains VID sets used for Port-and-Protocol-based VLAN Classification. |
| 1.3.6.1.4.1.171.11.70.9.2.18.2.1 | RowswL2dot1vProtocolPortEntry | not-accessible | current | A VID set for a port. |
| 1.3.6.1.4.1.171.11.70.9.2.18.2.1.1 | ColumnswL2dot1vProtocolPort | read-only | current | The port number of the port. |
| 1.3.6.1.4.1.171.11.70.9.2.18.2.1.2 | ColumnswL2dot1vProtocolPortGroupId | read-only | current | Designates a group of protocols in the Protocol Group Database. |
| 1.3.6.1.4.1.171.11.70.9.2.18.2.1.3 | ColumnswL2dot1vProtocolPortGroupVid | read-write | current | The VID associated with a group of protocols for each port. |
| 1.3.6.1.4.1.171.11.70.9.2.18.2.1.5 | ColumnswL2dot1vProtocolPortRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.11.70.9.2.19 | NodeswL2MulticastRangeMgmt | |||
| 1.3.6.1.4.1.171.11.70.9.2.19.1 | TableswL2MulticastRangeTable | not-accessible | current | A table contains multicast address range information. |
| 1.3.6.1.4.1.171.11.70.9.2.19.1.1 | RowswL2MulticastRangeEntry | not-accessible | current | Information about multicast address range. |
| 1.3.6.1.4.1.171.11.70.9.2.19.1.1.1 | ColumnswL2MulticastRangeName | read-only | current | The name of multicast address range. |
| 1.3.6.1.4.1.171.11.70.9.2.19.1.1.2 | ColumnswL2MulticastRangeHead | read-create | current | The head of multicast address range. |
| 1.3.6.1.4.1.171.11.70.9.2.19.1.1.3 | ColumnswL2MulticastRangeTail | read-create | current | The tail of multicast address range. |
| 1.3.6.1.4.1.171.11.70.9.2.19.1.1.4 | ColumnswL2MulticastRangeState | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.11.70.9.2.20 | NodeswL2LoopDetectMgmt | |||
| 1.3.6.1.4.1.171.11.70.9.2.20.1 | NodeswL2LoopDetectCtrl | |||
| 1.3.6.1.4.1.171.11.70.9.2.20.1.1 | ScalarswL2LoopDetectAdminState | read-write | current | This object indicates the loopback detection status for the system. |
| 1.3.6.1.4.1.171.11.70.9.2.20.1.2 | ScalarswL2LoopDetectInterval | read-write | current | This object indicates the interval value, the range is from 1 to 32767 seconds. |
| 1.3.6.1.4.1.171.11.70.9.2.20.1.3 | ScalarswL2LoopDetectRecoverTime | read-write | current | This object indicates the recover time, the range is from 60 to 1000000. The value of 0 disables the recover function. |
| 1.3.6.1.4.1.171.11.70.9.2.20.1.4 | ScalarswL2LoopDetectMode | read-write | current | This object indicates the loopback detection mode for the system. |
| 1.3.6.1.4.1.171.11.70.9.2.20.1.5 | ScalarswL2LoopDetectTrapMode | read-write | current | This object indicates the loopback detection trap mode for the system. |
| 1.3.6.1.4.1.171.11.70.9.2.20.2 | NodeswL2LoopDetectPortMgmt | |||
| 1.3.6.1.4.1.171.11.70.9.2.20.2.1 | TableswL2LoopDetectPortTable | not-accessible | current | The table specifies the loopback detection function specified by port. |
| 1.3.6.1.4.1.171.11.70.9.2.20.2.1.1 | RowswL2LoopDetectPortEntry | not-accessible | current | The table specifies the loopback detection function specified by port. |
| 1.3.6.1.4.1.171.11.70.9.2.20.2.1.1.1 | ColumnswL2LoopDetectPortIndex | read-only | current | This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module |
| 1.3.6.1.4.1.171.11.70.9.2.20.2.1.1.2 | ColumnswL2LoopDetectPortState | read-write | current | This object indicates the loopback detection function state on the port. |
| 1.3.6.1.4.1.171.11.70.9.2.20.2.1.1.3 | ColumnswL2LoopDetectPortLoopVLAN | read-only | current | This object indicates the VLAN list that has detected a loopback. |
| 1.3.6.1.4.1.171.11.70.9.2.20.2.1.1.4 | ColumnswL2LoopDetectPortLoopStatus | read-only | current | This object indicates the port status. |
| 1.3.6.1.4.1.171.11.70.9.2.24 | NodeswL2DhcpLocalRelayMgmt | |||
| 1.3.6.1.4.1.171.11.70.9.2.24.1 | ScalarswL2DhcpLocalRelayState | read-write | current | This object indicates the status of the DHCP local relay function of the switch. |
| 1.3.6.1.4.1.171.11.70.9.2.24.2 | TableswL2DhcpLocalRelayVLANTable | not-accessible | current | This table is used to manage the DHCP local relay status for each VLAN. |
| 1.3.6.1.4.1.171.11.70.9.2.24.2.1 | RowswL2DhcpLocalRelayVLANEntry | not-accessible | current | This object lists the current VLANs in the switch and their corresponding DHCP local relay status. |
| 1.3.6.1.4.1.171.11.70.9.2.24.2.1.1 | ColumnswL2DhcpLocalRelayVLANID | read-only | current | This object shows the VIDs of the current VLANS in the switch. |
| 1.3.6.1.4.1.171.11.70.9.2.24.2.1.2 | ColumnswL2DhcpLocalRelayVLANState | read-write | current | This object indicates the status of the DHCP relay function of the VLAN. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| IANAifMauAutoNegCapBits | BITS{ bOther(0), b10baseT(1), b10baseTFD(2), b100baseT4(3), b100baseTX(4), b100baseTXFD(5), b100baseT2(6), b100baseT2FD(7), bFdxPause(8), bFdxAPause(9), bFdxSPause(10), bFdxBPause(11), b1000baseX(12), b1000baseXFD(13), b1000baseT(14), b1000baseTFD(15) } | current | This data type is used as the syntax of the swL2PortAutoNegCapabilityBits, swL2PortAutoNegCapAdvertisedBits, and swL2PortAutoNegCapReceivedBits objects in swL2PortAutoNegTable. |