DKSF-PWR-OLD-MIB
103 objects
Generic MIB for NetPing remote sensing and control
Imported Objects
| SNMPv2-MIB | snmpTraps |
| SNMPv2-SMI | Counter32 Counter64 enterprises Gauge32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks |
| SNMPv2-TC | DisplayString TEXTUAL-CONVENTION TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.25728 | Nodelightcom | |||
| 1.3.6.1.4.1.25728.48 | IdentitynetPing8Pwr | Generic MIB for NetPing remote sensing and control | ||
| 1.3.6.1.4.1.25728.911 | NodenpReboot | |||
| 1.3.6.1.4.1.25728.911.1 | ScalarnpSoftReboot | read-write | current | Write 1 to reboot device after current operations completition |
| 1.3.6.1.4.1.25728.911.2 | ScalarnpResetStack | read-write | current | Write 1 to re-initialize network stack |
| 1.3.6.1.4.1.25728.911.3 | ScalarnpForcedReboot | read-write | current | Write 1 to immediate forced reboot |
| 1.3.6.1.4.1.25728.3800 | NodenpGsm | |||
| 1.3.6.1.4.1.25728.3800.1 | NodenpGsmInfo | |||
| 1.3.6.1.4.1.25728.3800.1.1 | ScalarnpGsmFailed | read-only | current | Firmware's GSM module status |
| 1.3.6.1.4.1.25728.3800.1.2 | ScalarnpGsmRegistration | read-only | current | Status of modem registration in GSM network (AT+CREG? result) |
| 1.3.6.1.4.1.25728.3800.1.3 | ScalarnpGsmStrength | read-only | current | GSM signal strength. 0..31 = 0..100%, 99 = unknown or n/a, 255 = updating info |
| 1.3.6.1.4.1.25728.3800.1.9 | ScalarnpGsmSendSms | read-write | current | Send arbitrary SMS. Format: [phone_number,phone_number,...] Message One to four destination phone numbers If [] and numbers omitted, mesagge will be sent to pr… |
| 1.3.6.1.4.1.25728.3800.2 | NodenpGsmTraps | |||
| 1.3.6.1.4.1.25728.3800.2.0 | NodenpGsmTrapPrefix | |||
| 1.3.6.1.4.1.25728.3800.2.0.1 | NotificationnpGsmTrap | current | GSM modem or SMS firmware problems | |
| 1.3.6.1.4.1.25728.3900 | NodenpBattery | |||
| 1.3.6.1.4.1.25728.3900.1 | NodenpBatteryInfo | |||
| 1.3.6.1.4.1.25728.3900.1.1 | ScalarnpBatteryPok | read-only | current | Power source |
| 1.3.6.1.4.1.25728.3900.1.2 | ScalarnpBatteryLevel | read-only | current | Battery charge, approximate value, in percent. Valid only if npBatteryPok = 0 |
| 1.3.6.1.4.1.25728.3900.1.3 | ScalarnpBatteryChg | read-only | current | Battery chargeing status. 0 if charging suspended or battery is full, 1 while LiPo fast charging. |
| 1.3.6.1.4.1.25728.5500 | NodenpRelay | |||
| 1.3.6.1.4.1.25728.5500.5 | TablenpRelayTable | not-accessible | current | Watchdog and outlet/relay control table |
| 1.3.6.1.4.1.25728.5500.5.1 | RownpRelayEntry | not-accessible | current | Relay/outlet table row |
| 1.3.6.1.4.1.25728.5500.5.1.1 | ColumnnpRelayN | read-only | current | The N of output relay |
| 1.3.6.1.4.1.25728.5500.5.1.2 | ColumnnpRelayMode | read-write | current | Control of relay: -1 - flip between on(1) and off(0) 0 - manual off 1 - manual on 2 - watchdog 3 - schedule 4 - both schedule and watchdog (while switched on b… |
| 1.3.6.1.4.1.25728.5500.5.1.3 | ColumnnpRelayStartReset | read-write | current | Write 1 to start reset (switch relay off for some time) |
| 1.3.6.1.4.1.25728.5500.5.1.6 | ColumnnpRelayMemo | read-only | current | Relay memo |
| 1.3.6.1.4.1.25728.5500.5.1.14 | ColumnnpRelayFlip | read-only | current | Write -1 to flip between manual on and manual off states of relay |
| 1.3.6.1.4.1.25728.5500.5.1.15 | ColumnnpRelayState | read-only | current | Actual relay state at the moment, regardless of source of control. 0 - relay is off 1 - relay is on |
| 1.3.6.1.4.1.25728.5500.5.1.16 | ColumnnpRelayPowered | read-only | current | AC presence on output. 0 - no AC dew to relay switched off or no ac on input 1 - AC is present |
| 1.3.6.1.4.1.25728.5800 | NodenpPwr | |||
| 1.3.6.1.4.1.25728.5800.3 | TablenpPwrTable | not-accessible | current | Watchdog and outlet/relay control table |
| 1.3.6.1.4.1.25728.5800.3.1 | RownpPwrEntry | not-accessible | current | Watchdog control table row |
| 1.3.6.1.4.1.25728.5800.3.1.1 | ColumnnpPwrChannelN | read-only | current | The id of watchdog/power channel |
| 1.3.6.1.4.1.25728.5800.3.1.2 | ColumnnpPwrStartReset | read-only | obsolete | Deprecated in current FW version: Write 1 to start forced reset. On read: 0 - normal operation 1 - reset is active 2 - reboot pause is active or watchdog is in… |
| 1.3.6.1.4.1.25728.5800.3.1.4 | ColumnnpPwrResetsCounter | read-write | current | Counter of watchdog resets Write 0 to clear. |
| 1.3.6.1.4.1.25728.5800.3.1.5 | ColumnnpPwrRepeatingResetsCounter | read-only | current | Counter of continous failed watchdog resets |
| 1.3.6.1.4.1.25728.5800.3.1.6 | ColumnnpPwrMemo | read-only | current | Watchdog channel memo |
| 1.3.6.1.4.1.25728.7900 | NodenpIr | |||
| 1.3.6.1.4.1.25728.7900.1 | NodenpIrCtrl | |||
| 1.3.6.1.4.1.25728.7900.1.1 | ScalarnpIrPlayCmd | read-write | current | Write IR command number to send IR command |
| 1.3.6.1.4.1.25728.7900.1.2 | ScalarnpIrReset | read-write | current | Write 1 to reset IR transiever. After reset, send IR command and check npIrStatus. |
| 1.3.6.1.4.1.25728.7900.1.3 | ScalarnpIrStatus | read-only | current | IR transiever status |
| 1.3.6.1.4.1.25728.8200 | NodenpSmoke | |||
| 1.3.6.1.4.1.25728.8200.1 | TablenpSmokeTable | not-accessible | current | Smoke Sensors Table |
| 1.3.6.1.4.1.25728.8200.1.1 | RownpSmokeEntry | not-accessible | current | Smoke Sensors Table Row |
| 1.3.6.1.4.1.25728.8200.1.1.1 | ColumnnpSmokeSensorN | read-only | current | The id of 1Wire Smoke sensor, 1 to 4 |
| 1.3.6.1.4.1.25728.8200.1.1.2 | ColumnnpSmokeStatus | read-only | current | Status of Smoke sensor |
| 1.3.6.1.4.1.25728.8200.1.1.3 | ColumnnpSmokePower | read-write | current | Controls power on Smoke sensor current loop |
| 1.3.6.1.4.1.25728.8200.1.1.4 | ColumnnpSmokeReset | read-write | current | Write 1 to switch off for approx. 10s to reset sensor |
| 1.3.6.1.4.1.25728.8200.1.1.6 | ColumnnpSmokeMemo | read-only | current | Smoke sensor memo |
| 1.3.6.1.4.1.25728.8200.2 | NodenpSmokeTraps | |||
| 1.3.6.1.4.1.25728.8200.2.0 | NodenpSmokeTrapPrefix | |||
| 1.3.6.1.4.1.25728.8200.2.0.1 | NotificationnpSmokeTrap | current | Status of 1W Smoke sensor has changed | |
| 1.3.6.1.4.1.25728.8200.2.1 | ScalarnpSmokeTrapSensorN | read-only | current | The id of 1Wire Smoke sensor, 1 to 4 |
| 1.3.6.1.4.1.25728.8200.2.2 | ScalarnpSmokeTrapStatus | read-only | current | New status of Smoke sensor |
| 1.3.6.1.4.1.25728.8200.2.6 | ScalarnpSmokeTrapMemo | read-only | current | Smoke sensor memo |
| 1.3.6.1.4.1.25728.8400 | NodenpRelHumidity | |||
| 1.3.6.1.4.1.25728.8400.2 | NodenpRelHumSensor | |||
| 1.3.6.1.4.1.25728.8400.2.2 | ScalarnpRelHumSensorValueH | read-only | current | Relative humidity value, % |
| 1.3.6.1.4.1.25728.8400.2.3 | ScalarnpRelHumSensorStatus | read-only | current | Status of the Rel.Humidity Sensor One 1=Normal, 0=Error or Sensor isn't connected |
| 1.3.6.1.4.1.25728.8400.2.4 | ScalarnpRelHumSensorValueT | read-only | current | Sensor temperature, deg.C |
| 1.3.6.1.4.1.25728.8400.2.5 | ScalarnpRelHumSensorStatusH | read-only | current | Status of Relative Humiduty |
| 1.3.6.1.4.1.25728.8400.2.7 | ScalarnpRelHumSafeRangeHigh | read-only | current | Relative Humidity safe range, top margin, %RH |
| 1.3.6.1.4.1.25728.8400.2.8 | ScalarnpRelHumSafeRangeLow | read-only | current | Relative Humidity safe range, bottom margin, %RH |
| 1.3.6.1.4.1.25728.8400.2.9 | ScalarnpRelHumSensorValueT100 | read-only | current | Sensor temperature, deg.C * 100 (fixed point two decimal places) Used to get access to the fractional part of T value |
| 1.3.6.1.4.1.25728.8400.9 | NodenpRelHumTraps | |||
| 1.3.6.1.4.1.25728.8400.9.0 | NodenpRelHumTrapPrefix | |||
| 1.3.6.1.4.1.25728.8400.9.0.1 | NotificationnpRelHumTrap | current | Status of Relative Humidity RH sensor has changed! | |
| 1.3.6.1.4.1.25728.8800 | NodenpThermo | |||
| 1.3.6.1.4.1.25728.8800.1 | TablenpThermoTable | not-accessible | current | Thermo Sensors Table |
| 1.3.6.1.4.1.25728.8800.1.1 | RownpThermoEntry | not-accessible | current | Thermo Sensors Table Row |
| 1.3.6.1.4.1.25728.8800.1.1.1 | ColumnnpThermoSensorN | read-only | current | The id of temperature sensor, 1 to 8 |
| 1.3.6.1.4.1.25728.8800.1.1.2 | ColumnnpThermoValue | read-only | current | Temperature, deg.C |
| 1.3.6.1.4.1.25728.8800.1.1.3 | ColumnnpThermoStatus | read-only | current | Temperature status (0=fault, 1=underheat, 2=normal, 3=overheat) |
| 1.3.6.1.4.1.25728.8800.1.1.4 | ColumnnpThermoLow | read-only | current | Bottom margin of normal temperature range, deg.C |
| 1.3.6.1.4.1.25728.8800.1.1.5 | ColumnnpThermoHigh | read-only | current | Top margin of normal temperature range, deg.C |
| 1.3.6.1.4.1.25728.8800.1.1.6 | ColumnnpThermoMemo | read-only | current | T channel memo |
| 1.3.6.1.4.1.25728.8800.2 | NodenpThermoTraps | |||
| 1.3.6.1.4.1.25728.8800.2.0 | NodenpThermoTrapPrefix | |||
| 1.3.6.1.4.1.25728.8800.2.0.1 | NotificationnpThermoTrap | current | Status of Thermo sensor is changed (crossing of normal temp. range) | |
| 1.3.6.1.4.1.25728.8800.2.1 | ScalarnpThermoTrapSensorN | read-only | current | The id of temperature sensor, 1 to 8 |
| 1.3.6.1.4.1.25728.8800.2.2 | ScalarnpThermoTrapValue | read-only | current | Temperature, deg.C |
| 1.3.6.1.4.1.25728.8800.2.3 | ScalarnpThermoTrapStatus | read-only | current | Temperature status (0=fault, 1=underheat, 2=normal, 3=overheat) |
| 1.3.6.1.4.1.25728.8800.2.4 | ScalarnpThermoTrapLow | read-only | current | Bottom margin of normal temperature range, deg.C |
| 1.3.6.1.4.1.25728.8800.2.5 | ScalarnpThermoTrapHigh | read-only | current | Top margin of normal temperature range, deg.C |
| 1.3.6.1.4.1.25728.8800.2.6 | ScalarnpThermoTrapMemo | read-only | current | T channel memo |
| 1.3.6.1.4.1.25728.8900 | NodenpIo | |||
| 1.3.6.1.4.1.25728.8900.1 | TablenpIoTable | not-accessible | current | Digital Input/output Table |
| 1.3.6.1.4.1.25728.8900.1.1 | RownpIoEntry | not-accessible | current | Digital Input/output Table Row |
| 1.3.6.1.4.1.25728.8900.1.1.1 | ColumnnpIoLineN | read-only | current | Number of IO line, from 1 to max supported |
| 1.3.6.1.4.1.25728.8900.1.1.2 | ColumnnpIoLevelIn | read-only | current | Input level, 0 or 1 |
| 1.3.6.1.4.1.25728.8900.1.1.3 | ColumnnpIoLevelOut | read-write | current | Output level, 0 or 1 |
| 1.3.6.1.4.1.25728.8900.1.1.6 | ColumnnpIoMemo | read-only | current | IO line memo |
| 1.3.6.1.4.1.25728.8900.1.1.9 | ColumnnpIoPulseCounter | read-write | current | Pulse Counter on IO input line (counts positive fronts) Write 0 to reset. |
| 1.3.6.1.4.1.25728.8900.1.1.12 | ColumnnpIoSinglePulseDuration | read-write | current | Set duration of single pulse on IO output line, 100ms to 25500ms, min. step is 100ms |
| 1.3.6.1.4.1.25728.8900.1.1.13 | ColumnnpIoSinglePulseStart | read-write | current | Write 1 to start single pulse on IO output. Output will be inverted for time, specified by npIoSinglePulseDuration |
| 1.3.6.1.4.1.25728.8900.2 | NodenpIoTraps | |||
| 1.3.6.1.4.1.25728.8900.2.0 | NodenpIoTrapPrefix | |||
| 1.3.6.1.4.1.25728.8900.2.0.1 | NotificationnpIoTrap | current | Input state of IO line is changed | |
| 1.3.6.1.4.1.25728.8900.2.1 | ScalarnpIoTrapLineN | read-only | current | Trap data, Number of IO line |
| 1.3.6.1.4.1.25728.8900.2.2 | ScalarnpIoTrapLevelIn | read-only | current | Trap data, new Input level, 0 or 1 |
| 1.3.6.1.4.1.25728.8900.2.6 | ScalarnpIoTrapMemo | read-only | current | Trap data, IO line memo |