MIB Viewer

E5-110-MIB

763 objects
No module-level DESCRIPTION found.
Imported Objects
BRIDGE-MIBBridgeId dot1dBasePort MacAddress Timeout
P-BRIDGE-MIBdot1dTrafficClass
Q-BRIDGE-MIBdot1qVlanIndex PortList VlanIndex
RFC1155-SMIenterprises
RFC1213-MIBDisplayString ifIndex PhysAddress
SNMPv2-SMICounter32 Counter64 Gauge32 IpAddress NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32
SNMPv2-TCRowStatus TEXTUAL-CONVENTION
OIDNameAccessStatusDescription
1.3.6.1.4.1.6321NodecalixNetworks
1.3.6.1.4.1.6321.1NodecalixRegistrations
1.3.6.1.4.1.6321.1.2NodecalixProducts
1.3.6.1.4.1.6321.1.2.3Nodee5x100
1.3.6.1.4.1.6321.1.2.3.1Nodee5x110
1.3.6.1.4.1.6321.1.2.3.1.2Nodealarmconf
1.3.6.1.4.1.6321.1.2.3.1.2.1ScalaralarmOpsread-writecurrentThe manager sets the corresponding bit value to 1 to start the operation and the agent clears the object to zero when the operation is successfully completed. …
1.3.6.1.4.1.6321.1.2.3.1.2.2TablealarmConfTablenot-accessiblecurrentThis table includes alarm configuration.
1.3.6.1.4.1.6321.1.2.3.1.2.2.1RowalarmConfEntrynot-accessiblecurrentAn entry in alarmConfTable.
1.3.6.1.4.1.6321.1.2.3.1.2.2.1.1ColumnalarmConfIdread-onlycurrent5000:adslLine_up 5001:adslLine_down 5002:adslPerf_lol_thresh 5003:adslPerf_lof_thresh 5004:adslPerf_los_thresh 5005:adslPerf_lop_thresh 5006:adslPerf_es_thresh…
1.3.6.1.4.1.6321.1.2.3.1.2.2.1.2ColumnalarmConfFacilityread-writecurrentAlarm facility.
1.3.6.1.4.1.6321.1.2.3.1.2.2.1.3ColumnalarmConfTargetread-writecurrentThe destination which alarms are reported to. Set the bit to 1 to enable the target. BIT 1: snmp trap BIT 2: syslog
1.3.6.1.4.1.6321.1.2.3.1.2.2.1.4ColumnalarmConfSeverityread-writecurrentAlarm severity
1.3.6.1.4.1.6321.1.2.3.1.2.2.1.5ColumnalarmConfClearableread-writecurrentSetting the object to one indicates that the alarm is to be cleared when user submits alarm clear.
1.3.6.1.4.1.6321.1.2.3.1.2.3TablealarmCurrTablenot-accessiblecurrentThis table includes current alarm information.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1RowalarmCurrEntrynot-accessiblecurrentAn entry in alarmCurrTable.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.1ColumnalarmCurrIndexread-onlycurrentIndex of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.2ColumnalarmCurrOccurTimeread-onlycurrentAlarm occurence time (in hundredths of a second) since the system was last re-initialized.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.3ColumnalarmCurrTrapOidread-onlycurrentTrap OID of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.4ColumnalarmCurrParam1read-onlycurrentThe 1st parameter of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.5ColumnalarmCurrParam2read-onlycurrentThe 2nd parameter of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.6ColumnalarmCurrParam3read-onlycurrentThe 3rd parameter of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.7ColumnalarmCurrParam4read-onlycurrentThe 4th parameter of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.8ColumnalarmCurrParam5read-onlycurrentThe 5th parameter of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.9ColumnalarmCurrParam6read-onlycurrentThe 6th parameter of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.10ColumnalarmCurrParam7read-onlycurrentThe 7th parameter of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.11ColumnalarmCurrParam8read-onlycurrentThe 8th parameter of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.12ColumnalarmCurrTimeDescrread-onlycurrentThe string representation of occurence time (YYYY/MM/DD HH:MM:SS).
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.13ColumnalarmCurrSeverityread-onlycurrentThe severity of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.3.1.14ColumnalarmCurrDescrread-onlycurrentThe description of the alarm.
1.3.6.1.4.1.6321.1.2.3.1.2.4TablealarmSeverityPortTablenot-accessiblecurrentThis table includes the configuration of alarm reporting severity threshold for each port.
1.3.6.1.4.1.6321.1.2.3.1.2.4.1RowalarmSeverityPortEntrynot-accessiblecurrentAn entry in alarmSeverityPortTable.
1.3.6.1.4.1.6321.1.2.3.1.2.4.1.1ColumnseverityThreshread-writecurrentThe minimum alarm severity that is reported.
1.3.6.1.4.1.6321.1.2.3.1.4Nodediagnostic
1.3.6.1.4.1.6321.1.2.3.1.4.3Nodeselt
1.3.6.1.4.1.6321.1.2.3.1.4.3.1ScalarseltTargetread-writecurrentIfIndex of the port which would be performed single end loopback test.
1.3.6.1.4.1.6321.1.2.3.1.4.3.2ScalarseltOpsread-writecurrentThe manager sets the object to 1 to start the selt and the agent clears the object to zero when selt is successfully completed.
1.3.6.1.4.1.6321.1.2.3.1.4.3.3ScalarseltStatusread-onlycurrentStatus description of the selt result.
1.3.6.1.4.1.6321.1.2.3.1.4.3.4ScalarseltCableTyperead-onlycurrentThe cable type that selt result indicates.
1.3.6.1.4.1.6321.1.2.3.1.4.3.5ScalarseltLoopEstimateLengthFtread-onlycurrentThe estimated loop length that selt result indicates.
1.3.6.1.4.1.6321.1.2.3.1.4.3.6ScalarseltLoopEstimateLengthMeterread-onlycurrentThe estimated loop length that selt result indicates.
1.3.6.1.4.1.6321.1.2.3.1.7Nodemulticast
1.3.6.1.4.1.6321.1.2.3.1.7.1ScalarigmpEnableread-writecurrentEnable/disable IGMP protocol.
1.3.6.1.4.1.6321.1.2.3.1.7.4NodemcastBandwidth
1.3.6.1.4.1.6321.1.2.3.1.7.4.1ScalarmcastDefaultBandwidthread-writecurrentDefault bandwidth requirement for a multicast channel.
1.3.6.1.4.1.6321.1.2.3.1.7.4.2ScalarmaxNumOfMcastBwread-onlycurrentThe maximum number of row entries that user can create in mcastBwTable.
1.3.6.1.4.1.6321.1.2.3.1.7.4.3TablemcastBwTablenot-accessiblecurrentThis table defines bandwidth budget for a range of multicast IP channels.
1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1RowmcastBwEntrynot-accessiblecurrentAn entry of mcastBwTable.
1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.1ColumnmcastBwIndexread-onlycurrentThe index which specify the entry.
1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.2ColumnmcastBwStartIpread-onlycurrentThe start multicast IP of the bandwidth control range.
1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.3ColumnmcastBwEndIpread-onlycurrentThe end multicast IP of the bandwidth control range.
1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.4ColumnmcastBwBandwidthread-createcurrentThe bandwidth budget for the multicast IP channels.
1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.5ColumnmcastBwRowStatusread-createcurrentThe row status of the entry.
1.3.6.1.4.1.6321.1.2.3.1.7.4.4TablemcastBwPortTablenot-accessiblecurrentThis table specify the multicast bandwidth control of the port.
1.3.6.1.4.1.6321.1.2.3.1.7.4.4.1RowmcastBwPortEntrynot-accessiblecurrentAn entry of mcastBwPortTable.
1.3.6.1.4.1.6321.1.2.3.1.7.4.4.1.1ColumnmcastBwPortEnableread-writecurrentEnable/disable multicast bandwidth control for a port.
1.3.6.1.4.1.6321.1.2.3.1.7.4.4.1.2ColumnmcastBwPortBandwidthread-writecurrentSet bandwidth threshold for a port.
1.3.6.1.4.1.6321.1.2.3.1.7.5NodeigmpCount
1.3.6.1.4.1.6321.1.2.3.1.7.5.1TableigmpCountPortTablenot-accessiblecurrentThis table specify the IGMP count limiting of the port.
1.3.6.1.4.1.6321.1.2.3.1.7.5.1.1RowigmpCountPortEntrynot-accessiblecurrentAn entry of igmpCountPortTable.
1.3.6.1.4.1.6321.1.2.3.1.7.5.1.1.1ColumnigmpCountPortEnableread-writecurrentEnable/disable IGMP count limiting for a port.
1.3.6.1.4.1.6321.1.2.3.1.7.5.1.1.2ColumnigmpCountPortLimitread-writecurrentThe maximum allowed IGMP report count for a port.
1.3.6.1.4.1.6321.1.2.3.1.7.6Nodemvlan
1.3.6.1.4.1.6321.1.2.3.1.7.6.1ScalarmaxNumOfMvlanread-onlycurrentThe maximum number of row entries that user can create in mvlanTable.
1.3.6.1.4.1.6321.1.2.3.1.7.6.2TablemvlanTablenot-accessiblecurrentA table containing static configuration information for each multicast VLAN configured into the device.
1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1RowmvlanEntrynot-accessiblecurrentAn entry of mvlanTable.
1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.1ColumnmvlanIndexread-onlycurrentThe VLAN-ID refering to this VLAN.
1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.2ColumnmvlanNameread-createcurrentAn administratively assigned string, which may be used to identify the VLAN.
1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.3ColumnmvlanEgressPortsread-createcurrentThe set of ports which are permanently assigned to the egress list for this multicast VLAN.
1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.4ColumnmvlanUntaggedPortsread-createcurrentThe set of ports which should transmit egress packets for this multicast VLAN as untagged.
1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.5ColumnmvlanRowStatusread-createcurrentThis object indicates the status of this entry.
1.3.6.1.4.1.6321.1.2.3.1.7.6.3TablemvlanTranslateTablenot-accessiblecurrentA table that contains multicast to VLAN translation.
1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1RowmvlanTranslateEntrynot-accessiblecurrentAn entry of mvlanTranslateTable.
1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1.1ColumnmvlanTranslateIndexread-onlycurrentThe index which specif the entry.
1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1.2ColumnmvlanTranslateStartIpread-writecurrentThe start IP of the multicast VLAN translation.
1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1.3ColumnmvlanTranslateEndIpread-writecurrentThe end IP of the multicast VLAN translation.
1.3.6.1.4.1.6321.1.2.3.1.7.7NodequeryVid
1.3.6.1.4.1.6321.1.2.3.1.7.7.1ScalarmaxNumOfQryVidread-onlycurrentThe maximum number of row entries that user can create in qryVidConfTable.
1.3.6.1.4.1.6321.1.2.3.1.7.7.2TableqryVidConfTablenot-accessiblecurrentThis table defines statically set VLANs used for response IGMP report.
1.3.6.1.4.1.6321.1.2.3.1.7.7.2.1RowqryVidConfEntrynot-accessiblecurrentAn entry in qryVidConfTable.
1.3.6.1.4.1.6321.1.2.3.1.7.7.2.1.1ColumnqryVidread-onlycurrentVLAN ID.
1.3.6.1.4.1.6321.1.2.3.1.7.7.2.1.2ColumnqryVidRowStatusread-createcurrentThis object indicates the status of this entry.
1.3.6.1.4.1.6321.1.2.3.1.7.7.3TableqryVidStatusTablenot-accessiblecurrentThis table shows statically set or dynamically learned VLANs used for response IGMP report.
1.3.6.1.4.1.6321.1.2.3.1.7.7.3.1RowqryVidStatusEntrynot-accessiblecurrentAn entry in qryVidStatusTable.
1.3.6.1.4.1.6321.1.2.3.1.7.7.3.1.1ColumnqryVidTyperead-onlycurrentVLAN type.
1.3.6.1.4.1.6321.1.2.3.1.7.9ScalarigmpVersionread-writecurrentSetting IGMP version.
1.3.6.1.4.1.6321.1.2.3.1.7.10ScalarigmpLeaveModeread-writecurrentConfigure IGMP leave message handling mode.
1.3.6.1.4.1.6321.1.2.3.1.7.11NodeigmpTimer
1.3.6.1.4.1.6321.1.2.3.1.7.11.1ScalarigmpQryIntervalread-writecurrentSet IGMP query interval, 10~1000 in seconds.
1.3.6.1.4.1.6321.1.2.3.1.7.11.2ScalarigmpRobustread-writecurrentSet IGMP query Robustness, 1~5.
1.3.6.1.4.1.6321.1.2.3.1.7.11.3ScalarigmpQryRespIntervalread-writecurrentSet IGMP query response interval, 1~100 in 100 milliseconds.
1.3.6.1.4.1.6321.1.2.3.1.7.11.4ScalarigmpLastMemQryIntervalread-writecurrentSet IGMP Last Member Query interval, 1~5 in 100 milliseconds.
1.3.6.1.4.1.6321.1.2.3.1.7.11.5ScalarigmpLastMemQryRobustread-writecurrentSet Last Member Query Robustness, 1~5.
1.3.6.1.4.1.6321.1.2.3.1.7.12NodeauditQuery
1.3.6.1.4.1.6321.1.2.3.1.7.12.1ScalarauditQryEnableread-writecurrentEnable/disable IGMP audit query.
1.3.6.1.4.1.6321.1.2.3.1.7.12.2ScalarauditQryIntervalread-writecurrentSet IGMP Audit Query Interval, 1~4 in 100 milliseconds.
1.3.6.1.4.1.6321.1.2.3.1.7.12.3ScalarauditQryRobustread-writecurrentSet IGMP Audit Query Robustness, 1~5.
1.3.6.1.4.1.6321.1.2.3.1.7.13NodeigmpProfile
1.3.6.1.4.1.6321.1.2.3.1.7.13.1ScalarmaxNumberOfIgmpProfilesread-onlycurrentThe max number of IGMP profiles in the system.
1.3.6.1.4.1.6321.1.2.3.1.7.13.2TableigmpProfileTablenot-accessiblecurrentA table that contains IGMP Profiles.
1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1RowigmpProfileEntrynot-accessiblecurrentThe entry of IGMP Profile table.
1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.1ColumnigmpProfileNameread-onlycurrentThe IGMP Profile name.
1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.2ColumnigmpProfileEnableread-writecurrentEnable/disable IGMP Profile.
1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.3ColumnigmpProfileMaxGroupread-writecurrentSet maximum allowed multicast group, 1~16.
1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.4ColumnigmpProfileRowStatusread-createcurrentThe row status of the IGMP Profile entry.
1.3.6.1.4.1.6321.1.2.3.1.7.13.3TableigmpFilterTablenot-accessiblecurrentA table that contains IGMP Filters.
1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1RowigmpFilterEntrynot-accessiblecurrentThe entry of IGMP Filter table.
1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1.1ColumnigmpFilterIndexread-onlycurrentThe index which specifies the filter rule.
1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1.2ColumnigmpFilterStartIpread-createcurrentThe start IP of the filter rule.
1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1.3ColumnigmpFilterEndIpread-createcurrentThe end IP of the filter rule.
1.3.6.1.4.1.6321.1.2.3.1.7.13.4TableigmpProfilePortTablenot-accessiblecurrentThis table specifies the IGMP Profile of the port.
1.3.6.1.4.1.6321.1.2.3.1.7.13.4.1RowigmpProfilePortEntrynot-accessiblecurrentAn entry in igmpProfilePortTable.
1.3.6.1.4.1.6321.1.2.3.1.7.13.4.1.1ColumnigmpProfilePortProfileread-writecurrentThe IGMP Profile of the port.
1.3.6.1.4.1.6321.1.2.3.1.8Nodeport
1.3.6.1.4.1.6321.1.2.3.1.8.1TablesubrPortTablenot-accessiblecurrentThis table includes subscriber attributes for the port.
1.3.6.1.4.1.6321.1.2.3.1.8.1.1RowsubrPortEntrynot-accessiblecurrentAn entry in subrPortTable.
1.3.6.1.4.1.6321.1.2.3.1.8.1.1.1ColumnsubrPortNameread-writecurrentName of the subscriber.
1.3.6.1.4.1.6321.1.2.3.1.8.1.1.2ColumnsubrPortTelread-writecurrentTelephone number of the subscriber.
1.3.6.1.4.1.6321.1.2.3.1.8.2NodeadslPort
1.3.6.1.4.1.6321.1.2.3.1.8.2.1TableadslLineConfTablenot-accessiblecurrentThis table includes common attributes describing the ADSL line.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1RowadslLineConfEntrynot-accessiblecurrentAn entry in adslLineConfTable.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.1ColumnadslLineConfAdslModeread-writecurrentG.lite and T1.413 are only applicable to annex A board. ETSI is only applicable to annex B board.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.2ColumnadslLineConfAnnexLread-writecurrentEnable/disable annex L for the port(Only in AnnexA).
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.3ColumnadslLineConfAnnexMread-writecurrentEnable/disable annex M for the port(For BCM AnnexA solution).
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.4ColumnadslLineConfAnnexIread-writecurrentEnable/disable annex I for the port(For BCM AnnexA solution).
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.5ColumnadslLineConfOptionMaskread-writecurrentThe semantic for each bit is: BIT 1 : Disable Trellis BIT 2 : Disable Reed-Solomon BIT 3 : Disable upstream bitswap BIT 4 : Disable downstream bitswap BIT 5 : …
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.6ColumnadslLineConfPowerMgmtread-writecurrentEnable/disable power management for the port.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.7ColumnadslLineConfPowerModeread-writecurrentThe power mode of the ADSL line.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.8ColumnadslLineConfAturMaxTxPowerread-writecurrentThe maximum allowed transmit power of ATU-R.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.9ColumnadslLineConfAtucMaxTxPowerread-writecurrentThe maximum allowed transmit power of ATU-C.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.10ColumnadslLineConfMaxRxPowerread-writecurrentThe maximum aggregate received power.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.11ColumnadslLineConfAturCarrierMaskread-writecurrentThe upstream carrier mask. For CTLM AnnexA solution, bin is from 0 to 31; CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63. Bit set…
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.12ColumnadslLineConfAtucCarrierMask0read-writecurrentThe downstream carrier mask. For CTLM AnnexA solution, bin is from 32 to 255; CTLM AnnexB solution, bin is from 64 to 255; BCM solution, bin is from 32 to 255.…
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.13ColumnadslLineConfAtucCarrierMask1read-writecurrentThe downstream carrier mask from bin 256 to 511. Bit set to 1 indicates the bin is masked off.
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.14ColumnadslLineConfAturInpread-writecurrentThe upstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can s…
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.15ColumnadslLineConfAtucInpread-writecurrentThe downstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can…
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.16ColumnadslLineConfL0Timeread-writecurrentSet the minimum time in seconds that the ADSL line must stay in L0 power mode before changing to the L2 power mode. For CTLM solution, the range is 120 ~ 65535…
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.17ColumnadslLineConfL2Timeread-writecurrentSet minimum time in seconds that the ADSL line must stay in the L2 power mode before reducing the power again in the L2 power mode. For CTLM solution, the rang…
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.18ColumnadslLineConfL2ATPRread-writecurrentSet the maximum Aggregate Transmit Power Reduction (ATPR) in decibels (dB) that is permitted in a L2 power reduction. The system can gradually decrease the ADS…
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.19ColumnadslLineConfL2ATPRTread-writecurrentthe maximum Aggregate Transmit Power Reduction Total (ATPRT) in decibels (dB) that is permitted in the L2 power mode. This is the total transmit power decrease…
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.20ColumnadslLineConfMaxL2Rateread-writecurrentconfigured maximum L2 rate. (32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.21ColumnadslLineConfMinL2Rateread-writecurrentconfigured minimum L2 rate. (32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.22ColumnadslLineConfL0toL2Rateread-writecurrentconfigured transition L0 to L2 rate. (<=min_l2rate/2 and >= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.23ColumnadslLineConfNitroread-writecurrentEnable/disable nitro mode for the port(For BCM solution).
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.24ColumnadslLineConfUSPhyrread-writecurrentEnable/disable Upstream PHYR for the port(For BCM solution).
1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.25ColumnadslLineConfDSPhyrread-writecurrentEnable/disable Downstream PHYR for the port(For BCM solution).
1.3.6.1.4.1.6321.1.2.3.1.8.2.3NodeadslPortBatchSet
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.1ScalaradslPortTargetread-writecurrentThe managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: 0, Reserved(chaises) …
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.2ScalaradslPortOpsread-writecurrentThe managed object is for ADSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the correspond…
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.3ScalaradslPortOps2read-writecurrentThe managed object is for ADSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the correspond…
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.4ScalaradslModeForBatchSetread-writecurrentG.lite and T1.413 are only applicable to annex A board. ETSI is only applicable to annex B board.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.5ScalaradslLineProfileForBatchSetread-writecurrentThe ADSL line profile.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.6ScalaradslAlarmProfileForBatchSetread-writecurrentThe ADSL alarm profile.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.7ScalaradslOptionMaskForBatchSetread-writecurrentThe semantic for each bit is identical to the object adslLineConfOptionMask.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.8ScalaradslAturMaxTxPowerForBatchSetread-writecurrentThe maximum allowed transmit power of ATU-R.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.9ScalaradslAtucMaxTxPowerForBatchSetread-writecurrentThe maximum allowed transmit power of ATU-C.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.10ScalaradslMaxRxPowerForBatchSetread-writecurrentThe maximum aggregate received power.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.11ScalaradslAturCarrierMaskForBatchSetread-writecurrentThe upstream carrier mask.For CTLM AnnexA solution, bin is from 0 to 31; CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63. Bit set …
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.12ScalaradslAtucCarrierMask0ForBatchSetread-writecurrentThe downstream carrier mask from bin 32 to 255. Bit set to 1 indicates the bin is masked off.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.13ScalaradslAtucCarrierMask1ForBatchSetread-writecurrentThe downstream carrier mask from bin 256 to 511. Bit set to 1 indicates the bin is masked off.
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.14ScalaradslAturInpForBatchSetread-writecurrentThe upstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can s…
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.15ScalaradslAtucInpForBatchSetread-writecurrentThe downstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can…
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.16ScalaradslL0TimeForBatchSetread-writecurrentSet the minimum time in seconds that the ADSL line must stay in L0 power mode before changing to the L2 power mode. For CTLM solution, the range is 120 ~ 65535…
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.17ScalaradslL2TimeForBatchSetread-writecurrentSet minimum time in seconds that the ADSL line must stay in the L2 power mode before reducing the power again in the L2 power mode. For CTLM solution, the rang…
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.18ScalaradslL2ATPRForBatchSetread-writecurrentSet the maximum Aggregate Transmit Power Reduction (ATPR) in decibels (dB) that is permitted in a L2 power reduction. The system can gradually decrease the ADS…
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.19ScalaradslL2ATPRTForBatchSetread-writecurrentthe maximum Aggregate Transmit Power Reduction Total (ATPRT) in decibels (dB) that is permitted in the L2 power mode. This is the total transmit power decrease…
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.20ScalaradslMaxL2RateForBatchSetread-writecurrentconfigured maximum L2 rate. (32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.21ScalaradslMinL2RateForBatchSetread-writecurrentconfigured minimum L2 rate. (32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)
1.3.6.1.4.1.6321.1.2.3.1.8.2.3.22ScalaradslL0toL2RateForBatchSetread-writecurrentconfigured transition L0 to L2 rate. (<=min_l2rate/2 and >= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)
1.3.6.1.4.1.6321.1.2.3.1.8.2.4TableadslLineStatusTablenot-accessiblecurrentThis table includes the ADSL line status.
1.3.6.1.4.1.6321.1.2.3.1.8.2.4.1RowadslLineStatusEntrynot-accessiblecurrentAn entry in adslLineStatusTable.
1.3.6.1.4.1.6321.1.2.3.1.8.2.4.1.1ColumnadslLineStatusModeread-onlycurrentThe link up mode of the ADSL line.
1.3.6.1.4.1.6321.1.2.3.1.8.2.4.1.2ColumnadslLineUpTimeread-onlycurrentThe link up time of the ADSL line, in unit of seconds
1.3.6.1.4.1.6321.1.2.3.1.8.2.5TablepowerMgmtParamTablenot-accessiblecurrentThis table defines L0 to L2 power transition parameters.
1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1RowpowerMgmtParamEntrynot-accessiblecurrentAn entry in powerMgmtParamTable.
1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.1ColumnpowerMgmtL0Timeread-writecurrentThe object specifies the minimum time in L0 mode before L2 mode may be entered.
1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.2ColumnpowerMgmtL2Timeread-writecurrentThe object specifies the minimum time in L2 mode before trimming and in between power trims.
1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.3ColumnpowerMgmtL2Atprread-writecurrentThe maximum Aggregate Transmit Power Reduction.
1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.4ColumnpowerMgmtL2Atprtread-writecurrentThe maximum Aggregate Transmit Power Reduction Total.
1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.5ColumnpowerMgmtL2MinRateread-writecurrentThe object specifies the minimum L2 rate.
1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.6ColumnpowerMgmtL2MaxRateread-writecurrentThe object specifies the maximum L2 rate.
1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.7ColumnpowerMgmtL2ThreshRateread-writecurrentThe object specifies the rate threshold that triggers the line entering L0 or L2 mode.
1.3.6.1.4.1.6321.1.2.3.1.8.2.6TablepowerMgmtPSDTablenot-accessiblecurrentThis table provides the PSD setting for both ATU-C and ATU-R.
1.3.6.1.4.1.6321.1.2.3.1.8.2.6.1RowpowerMgmtPSDEntrynot-accessiblecurrentAn entry in powerMgmtPSDTable.
1.3.6.1.4.1.6321.1.2.3.1.8.2.6.1.1ColumnpowerMgmtAtucMaxPSDread-writecurrentThe object specifies the maximum ATU-C PSD.
1.3.6.1.4.1.6321.1.2.3.1.8.2.6.1.2ColumnpowerMgmtAturMaxPSDread-writecurrentThe object specifies the maximum ATU-R PSD.
1.3.6.1.4.1.6321.1.2.3.1.8.4Nodepvc
1.3.6.1.4.1.6321.1.2.3.1.8.4.1ScalarmaxNumOfPvcsread-onlycurrentThe maximum number of PVCs which could be created on a port.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2TablepvcTablenot-accessiblecurrentThis table includes PVC configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1RowpvcEntrynot-accessiblecurrentAn entry in pvcTable.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.1ColumnpvcVpiread-onlycurrentVPI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.2ColumnpvcVciread-onlycurrentVCI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.3ColumnpvcPvidread-onlycurrentDefault VID of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.5ColumnpvcPriorityread-createcurrent802.1p default priority of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.6ColumnpvcProfileDSread-createcurrentThe value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.7ColumnpvcRowStatusread-createcurrentThis object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.8ColumnpvcProfileUSread-createcurrentThe value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.11ColumnpvcAcNameread-createcurrentAccess concentrator name for paepvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.12ColumnpvcServiceNameread-createcurrentService name for paepvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.13ColumnpvcHelloTimeread-createcurrentThe system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
1.3.6.1.4.1.6321.1.2.3.1.8.4.3TablepvcStateTableread-onlycurrentThis table show current PVC status.
1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1RowpvcStateEntryread-onlycurrentAn entry in pvcStateTable.
1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.1ColumnpvcStateVpiread-onlycurrentVPI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.2ColumnpvcStateVciread-onlycurrentVCI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.3ColumnpvcStatePvidread-onlycurrentDefault VID of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.4ColumnpvcStatePriorityread-onlycurrent802.1p default priority of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.8ColumnpvcStateChannelTyperead-onlycurrentThe value of this object identifies the channel type at runtime.
1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.9ColumnpvcStateEncapread-onlycurrentThe value of this object identifies the channel encapsulation at runtime.
1.3.6.1.4.1.6321.1.2.3.1.8.4.4TablepvcUsRateLimitTablenot-accessiblecurrentThis table defines the upstream rate limit for each PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.4.4.1RowpvcUsRateLimitEntrynot-accessiblecurrentAn entry in pvcUsRateLimitTable.
1.3.6.1.4.1.6321.1.2.3.1.8.4.4.1.1ColumnpvcUsRateLimitEnableread-writecurrentEnable/disable upstream rate limit for a PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.4.4.1.2ColumnpvcUsRateLimitread-writecurrentUpstream rate limit in Kbps for a PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.5Nodeppvc
1.3.6.1.4.1.6321.1.2.3.1.8.5.1ScalarmaxNumOfPriorityPvcsread-onlycurrentThe maximum number of priority PVCs which could be created on a port.
1.3.6.1.4.1.6321.1.2.3.1.8.5.2TableppvcTablenot-accessiblecurrentThis table includes priority PVC configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1RowppvcEntrynot-accessiblecurrentAn entry in ppvcTable.
1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.1ColumnppvcVpiread-onlycurrentVPI of the ppvc.
1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.2ColumnppvcVciread-onlycurrentVCI of the ppvc.
1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.3ColumnppvcPvidread-onlycurrentDefault VID of the ppvc.
1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.4ColumnppvcEncapread-createcurrentEncapsulation of the ppvc.
1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.5ColumnppvcPriorityread-createcurrent802.1p default priority of the ppvc.
1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.6ColumnppvcRowStatusread-createcurrentThis object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.5.4TableppvcMemberTablenot-accessiblecurrentThis table includes priority PVC member configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1RowppvcMemberEntrynot-accessiblecurrentAn entry in ppvcMemberTable.
1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.1ColumnppvcMemberVpiread-onlycurrentVPI of the member ppvc.
1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.2ColumnppvcMemberVciread-onlycurrentVCI of the member ppvc.
1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.3ColumnppvcMemberPriorityread-onlycurrent802.1p default priority of the member ppvc.
1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.4ColumnppvcMemberProfileDSread-createcurrentThe profile of the member ppvc in DS side.
1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.5ColumnppvcMemberRowStatusread-createcurrentThis object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.6ColumnppvcMemberProfileUSread-createcurrentThe profile of the member ppvc in US side.
1.3.6.1.4.1.6321.1.2.3.1.8.8Noderpvc
1.3.6.1.4.1.6321.1.2.3.1.8.8.1TablerpvcGatewayTablenot-accessiblecurrentThis table includes Routed Gateway configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1RowrpvcGatewayEntrynot-accessiblecurrentAn entry in Routed Gateway table.
1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.1ColumnrpvcGatewayIpread-onlycurrentIP of RPVC gateway.
1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.2ColumnrpvcGatewayVlanIdread-writecurrentVlan id send to this RPVC gateway.
1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.3ColumnrpvcGatewayRowStatusread-createcurrentThis object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.4ColumnrpvcGatewayPriorityread-writecurrent802.1p p bit send to this RPVC gateway.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2TablerpvcTablenot-accessiblecurrentThis table includes RPVC configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1RowrpvcEntrynot-accessiblecurrentAn entry in rpvcTable.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.1ColumnrpvcVpiread-onlycurrentVPI of the rpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.2ColumnrpvcVciread-onlycurrentVCI of the rpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.3ColumnrpvcDSProfileread-createcurrentThe down stream profile of the rpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.4ColumnrpvcUSProfileread-createcurrentThe up stream profile of the rpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.5ColumnrpvcIpread-onlycurrentThe IP of the rpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.6ColumnrpvcNetmaskread-onlycurrentThe IP mask of the rpvc IP.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.7ColumnrpvcGatewayIpAddressread-createcurrentThe gateway IP of rpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.8ColumnrpvcRowStatusread-createcurrentThis object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.8.3TablerpvcRouteDomainTablenot-accessiblecurrentThis table includes RPVC route domain configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1RowrpvcRouteDomainEntrynot-accessiblecurrentAn entry in rpvcRouteDomainTable.
1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.1ColumnrpvcRouteDomainVpiread-onlycurrentVPI of the rpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.2ColumnrpvcRouteDomainVciread-onlycurrentVCI of the rpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.3ColumnrpvcRouteDomainIpread-onlycurrentThe route domain IP.
1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.4ColumnrpvcRouteDomainNetmaskread-onlycurrentThe IP mask of the route domain IP.
1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.5ColumnrpvcRouteDomainRowStatusread-createcurrentThis object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.8.4ScalarrpvcArpAgingTimeread-writecurrentSet RPVC ARP proxy aging time 10..10000 seconds, 0 to disable againg.
1.3.6.1.4.1.6321.1.2.3.1.8.8.5ScalarrpvcArpFlushread-writecurrentFlush the RPVC ARP proxy table.
1.3.6.1.4.1.6321.1.2.3.1.8.9TabledsBcastDisableTablenot-accessiblecurrentThis table includes Down Stream Bcast configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.9.1RowdsBcastDisableEntrynot-accessiblecurrentAn entry in Down Stream Bcast table.
1.3.6.1.4.1.6321.1.2.3.1.8.9.1.1ColumndsBcastDisableVlanIdread-onlycurrentdownstream broadcast disabled vid.
1.3.6.1.4.1.6321.1.2.3.1.8.9.1.2ColumndsBcastDisableRowStatusread-createcurrentThis object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.10Nodepaepvc
1.3.6.1.4.1.6321.1.2.3.1.8.10.1TablepaepvcTablenot-accessiblecurrentThis table includes PPPoAoE PVC configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1RowpaepvcEntrynot-accessiblecurrentAn entry of paepvcTable.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.1ColumnpaepvcVpiread-onlycurrentVPI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.2ColumnpaepvcVciread-onlycurrentVCI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.3ColumnpaepvcPvidread-onlycurrentDefault VID of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.5ColumnpaepvcPriorityread-createcurrent802.1p default priority of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.6ColumnpaepvcProfileDSread-createcurrentThe value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.7ColumnpaepvcAcNameread-createcurrentAccess concentrator name.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.8ColumnpaepvcServiceNameread-createcurrentService name.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.9ColumnpaepvcHelloTimeread-createcurrentThe system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.10ColumnpaepvcRowStatusread-createcurrentThis object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.11ColumnpaepvcProfileUSread-createcurrentThe value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.12ColumnpaepvcCvidread-createcurrentDefault C-VID of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.13ColumnpaepvcCPriorityread-createcurrent802.1p default C-priority of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.11Nodetlspvc
1.3.6.1.4.1.6321.1.2.3.1.8.11.1TabletlspvcTablenot-accessiblecurrentThis table includes Transparent LAN Service (TLS) PVC configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1RowtlspvcEntrynot-accessiblecurrentAn entry of tlspvcTable.
1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.1ColumntlspvcVpiread-onlycurrentVPI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.2ColumntlspvcVciread-onlycurrentVCI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.3ColumntlspvcSvidread-onlycurrents-tag VLAN ID of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.5ColumntlspvcSpriorityread-createcurrents-tag priority of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.6ColumntlspvcProfileDSread-createcurrentThe value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side.
1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.7ColumntlspvcRowStatusread-createcurrentThis object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.8ColumntlspvcProfileUSread-createcurrentThe value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side.
1.3.6.1.4.1.6321.1.2.3.1.8.12Nodeipbpvc
1.3.6.1.4.1.6321.1.2.3.1.8.12.1TableipbpvcDomainTablenot-accessiblecurrentThis table includes ipbpvc domain configuration. This table is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.1.1RowipbpvcDomainEntrynot-accessiblecurrentAn entry of ipbpvcDomainTable.
1.3.6.1.4.1.6321.1.2.3.1.8.12.1.1.1ColumnipbpvcDomainNameread-onlycurrentName of the domain.
1.3.6.1.4.1.6321.1.2.3.1.8.12.1.1.2ColumnipbpvcDomainRowStatusread-createcurrentRow status of the table.
1.3.6.1.4.1.6321.1.2.3.1.8.12.2TableipbpvcDomainVlanTablenot-accessiblecurrentThis table includes ipbpvc domain VLAN configuration. This table is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1RowipbpvcDomainVlanEntrynot-accessiblecurrentAn entry of ipbpvcDomainVlanTable.
1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1.1ColumnipbpvcDomainVlanIdread-onlycurrentSet VLAN to join or leave the specified domain.
1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1.2ColumnipbpvcDomainDhcpVlanEnableread-createcurrentEnable/disable DHCP VLAN in a domain.
1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1.3ColumnipbpvcDomainVlanRowStatusread-createcurrentRow status of the table used to create/delete an entry.
1.3.6.1.4.1.6321.1.2.3.1.8.12.3TableipbpvcEdgeRouterTablenot-accessiblecurrentThis table includes ipbpvc edge router configuration. This table is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1RowipbpvcEdgeRouterEntrynot-accessiblecurrentAn entry of ipbpvcEdgeRouterTable.
1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.1ColumnipbpvcEdgeRouterIpread-onlycurrentIP address of the edge router.
1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.2ColumnipbpvcEdgeRouterVidread-onlycurrentVLAN ID of the edge router.
1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.3ColumnipbpvcEdgeRouterMaskread-onlycurrentNetmask of the edge router.
1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.4ColumnipbpvcEdgeRouterRowStatusread-createcurrentRow status of the table used to create/delete an entry.
1.3.6.1.4.1.6321.1.2.3.1.8.12.4TableipbpvcInterfaceTablenot-accessiblecurrentThis table includes ipbpvc interface configuration. This table is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1RowipbpvcInterfaceEntrynot-accessiblecurrentAn entry of ipbpvcInterfaceTable.
1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.1ColumnipbpvcInterfaceIpread-onlycurrentIP address of the interface.
1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.2ColumnipbpvcInterfaceMaskread-onlycurrentNetmask of the interface.
1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.3ColumnipbpvcInterfaceVidread-onlycurrentVLAN ID of the interface.
1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.4ColumnipbpvcInterfaceIfIndexread-createcurrentIfIndex of the interface.
1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.5ColumnipbpvcInterfaceVpiread-createcurrentVPI of the interface.
1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.6ColumnipbpvcInterfaceVciread-createcurrentVCI of the interface.
1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.7ColumnipbpvcInterfaceRowStatusread-createcurrentRow status of the table used to create/delete an entry.
1.3.6.1.4.1.6321.1.2.3.1.8.12.5TableipbpvcRouteTablenot-accessiblecurrentThis table includes ipbpvc route configuration. This table is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1RowipbpvcRouteEntrynot-accessiblecurrentAn entry of ipbpvcRouteTable.
1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.1ColumnipbpvcRouteIpread-onlycurrentIP address of the route.
1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.2ColumnipbpvcRouteMaskread-onlycurrentNetmask of the route.
1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.3ColumnipbpvcRouteNextHopread-onlycurrentNext hop IP address of the route.
1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.4ColumnipbpvcRouteMetricread-createcurrentMetric of the route.
1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.5ColumnipbpvcRoutePriorityread-createcurrentPriority of the route. Note that the default value of this object is 8, which means we keep the original priority of the packet(frame).
1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.6ColumnipbpvcRouteRowStatusread-createcurrentRow status of the table used to create/delete an entry.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6TableipbpvcTablenot-accessiblecurrentThis table includes ipbpvc configuration. This table is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1RowipbpvcEntrynot-accessiblecurrentAn entry of ipbpvcTable.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.1ColumnipbpvcVpiread-onlycurrentVPI of the PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.2ColumnipbpvcVciread-onlycurrentVCI of the PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.3ColumnipbpvcPvidread-onlycurrentPVID of the PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.4ColumnipbpvcEncapread-createcurrentType of the PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.5ColumnipbpvcPriorityread-createcurrentPriority of the PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.6ColumnipbpvcProfileread-createcurrentProfile of the PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.7ColumnipbpvcRowStatusread-createcurrentRow status of the table used to create/delete an entry.
1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.8ColumnipbpvcProfileUSread-createcurrentUS Profile of the PVC.
1.3.6.1.4.1.6321.1.2.3.1.8.12.8Nodearpproxy
1.3.6.1.4.1.6321.1.2.3.1.8.12.8.1ScalararpproxyAgeread-writecurrentAging time of the ARP proxy. This object is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2NodearpproxyFlush
1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.1ScalararpproxyFlushTargetread-writecurrentThe target whose ARP table to be flushed. This object is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.2ScalararpproxyFlushOpsread-writecurrentSet the object to 1 to start flushing. This object is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.3ScalararpproxyFlushEdgeRouterIpread-writecurrentFlush ARP table for the specified edge router. This object is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.4ScalararpproxyFlushEdgeRouterVidread-writecurrentFlush ARP table for the specified edge router. This object is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.5ScalararpproxyFlushInterfaceIpread-writecurrentFlush ARP table for the specified interface. This object is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.6ScalararpproxyFlushInterfaceMaskread-writecurrentFlush ARP table for the specified interface. This object is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.7ScalararpproxyFlushInterfaceVidread-writecurrentFlush ARP table for the specified interface. This object is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.8.14Nodedtpvc
1.3.6.1.4.1.6321.1.2.3.1.8.14.1TabledtpvcTablenot-accessiblecurrentThis table includes Double Tagging (DT) PVC configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1RowdtpvcEntrynot-accessiblecurrentAn entry of dtpvcTable.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.1ColumndtpvcVpiread-onlycurrentVPI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.2ColumndtpvcVciread-onlycurrentVCI of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.3ColumndtpvcSvidread-onlycurrents-tag VLAN ID of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.4ColumndtpvcSpriorityread-createcurrents-tag priority of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.5ColumndtpvcCvidread-createcurrentc-tag VLAN ID of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.6ColumndtpvcCpriorityread-createcurrentc-tag priority of the pvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.7ColumndtpvcDSProfileread-createcurrentThe value of this object identifies the row in the atmProfileTable, which applies for this dtpvc in DS side.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.8ColumndtpvcUSProfileread-createcurrentThe value of this object identifies the row in the atmProfileTable, which applies for this dtpvc in US side.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.9ColumndtpvcRowStatusread-createcurrentThis object is used to create a new row or delete an existing row in this table.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.10ColumndtpvcSuperChannelread-createcurrentSpecified the configured DTPVC is a super channel.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.11ColumndtpvcAcNameread-createcurrentAccess concentrator name for paepvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.12ColumndtpvcServiceNameread-createcurrentService name for paepvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.13ColumndtpvcHelloTimeread-createcurrentThe system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2TabledtpvcStateTablenot-accessiblecurrentThis table show current DTPVC status.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1RowdtpvcStateEntrynot-accessiblecurrentAn entry in dtpvcStateTable.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.1ColumndtpvcStateVpiread-onlycurrentVPI of the dtpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.2ColumndtpvcStateVciread-onlycurrentVCI of the dtpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.3ColumndtpvcStateSvidread-onlycurrentDefault S-VID of the dtpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.4ColumndtpvcStateSPriorityread-onlycurrentS-priority of the dtpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.5ColumndtpvcStateCvidread-onlycurrentDefault C-VID of the dtpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.6ColumndtpvcStateCPriorityread-onlycurrentC-priority of the dtpvc.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.8ColumndtpvcStateChannelTyperead-onlycurrentThe value of this object identifies the channel type at runtime.
1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.9ColumndtpvcStateEncapread-onlycurrentThe value of this object identifies the channel encapsulation at runtime.
1.3.6.1.4.1.6321.1.2.3.1.8.15NodesnrMgn
1.3.6.1.4.1.6321.1.2.3.1.8.15.1TablesnrMgnTablenot-accessiblecurrentA table containing the per port SNR Margin configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1RowsnrMgnEntrynot-accessiblecurrentAn entry of snrMgnTable.
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.1ColumnsnrMgnModeread-writecurrentConfigure DSL SNR margin configuration mode of the specified ports. Profile: the SNR margin configuration comes from DSL profile. Line: the SNR margin configur…
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.2ColumnsnrMgnUcTargetread-writecurrentConfigured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.3ColumnsnrMgnUcMaxread-writecurrentConfigured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operat…
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.4ColumnsnrMgnUcMinread-writecurrentConfigured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that i…
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.5ColumnsnrMgnUcDownshiftread-writecurrentConfigured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the c…
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.6ColumnsnrMgnUcUpshiftread-writecurrentConfigured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the cas…
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.7ColumnsnrMgnUrTargetread-writecurrentConfigured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.8ColumnsnrMgnUrMaxread-writecurrentConfigured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operat…
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.9ColumnsnrMgnUrMinread-writecurrentConfigured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that i…
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.10ColumnsnrMgnUrDownshiftread-writecurrentConfigured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the c…
1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.11ColumnsnrMgnUrUpshiftread-writecurrentConfigured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the cas…
1.3.6.1.4.1.6321.1.2.3.1.8.16NodedslRate
1.3.6.1.4.1.6321.1.2.3.1.8.16.1TabledslRateTablenot-accessiblecurrentA table containing the per port DSL Rate configuration.
1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1RowdslRateEntrynot-accessiblecurrentAn entry of dslRateTable.
1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.1ColumndslRateModeread-writecurrentConfigure DSL Rate configuration mode of the specified ports. Profile: the DSL Rate configuration comes from DSL profile. Line: the DSL Rate configuration come…
1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.2ColumndslRateLatencyModeread-onlycurrentThe latency mode is fast or interleave
1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.3ColumndslRateXtucMaxInterleaveDelayread-writecurrentConfigured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) betwee…
1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.4ColumndslRateXtucMaxTxRateread-writecurrentConfigured Maximum Transmit rate for `Fast' or `Interleave' channels, in bps.
1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.5ColumndslRateXtucMinTxRateread-writecurrentConfigured Minimum Transmit rate for `Fast' or `Interleave' channels, in bps
1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.6ColumndslRateXturMaxInterleaveDelayread-writecurrentConfigured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) betwee…
1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.7ColumndslRateXturMaxTxRateread-writecurrentConfigured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.8ColumndslRateXturMinTxRateread-writecurrentConfigured Maximum Transmit rate for `Fast' or `Interleave' channels, in bps.
1.3.6.1.4.1.6321.1.2.3.1.8.51Nodegbond
1.3.6.1.4.1.6321.1.2.3.1.8.51.1TablegbondGroupTablenot-accessiblecurrentA table containing the G.Bond configuration information for each bonding group of the device.
1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1RowgbondGroupEntrynot-accessiblecurrentAn entry of gbondTable.
1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.1ColumngbondGroupNameread-onlycurrentAn administratively assigned string, which may be used to identify bonding group.
1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.2ColumngbondGroupPortsread-createcurrentThe set of ports which are currently assigned to the bonding group of specified group name. Byte 1: Reserved(chassis) Byte 2~3: Reserved(slot) Byte 4: Reserved…
1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.4ColumngbondGroupUpRateread-onlycurrentThe UP stream rate.
1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.5ColumngbondGroupDownRateread-onlycurrentThe DOWN stream rate.
1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.6ColumngbondGroupRowStatusread-createcurrentThis object indicates the status of this entry.
1.3.6.1.4.1.6321.1.2.3.1.10Nodeswitch
1.3.6.1.4.1.6321.1.2.3.1.10.10Nodedscp
1.3.6.1.4.1.6321.1.2.3.1.10.10.1TabledscpMappingTablenot-accessiblecurrentThe table contains DSCP mapping configuration for the adsl and ethernet ports.
1.3.6.1.4.1.6321.1.2.3.1.10.10.1.1RowdscpMappingEntrynot-accessiblecurrentAn entry of dscpMappingTable.
1.3.6.1.4.1.6321.1.2.3.1.10.10.1.1.1ColumndscpSrcCodePointread-onlycurrentThe DSCP source code point used for mapping.
1.3.6.1.4.1.6321.1.2.3.1.10.10.1.1.3ColumndscpMapPriorityread-writecurrentThe mapping p bits that will replace the source p bits in the incoming packet.
1.3.6.1.4.1.6321.1.2.3.1.10.10.2TabledscpPortTablenot-accessiblecurrentThe table contains DSCP mapping configuration for the adsl and ethernet ports.
1.3.6.1.4.1.6321.1.2.3.1.10.10.2.1RowdscpPortEntrynot-accessiblecurrentAn entry of dscpPortTable.
1.3.6.1.4.1.6321.1.2.3.1.10.10.2.1.1ColumndscpStatusEnableread-writecurrentThe DSCP port status.
1.3.6.1.4.1.6321.1.2.3.1.10.12NodevlanIsolation
1.3.6.1.4.1.6321.1.2.3.1.10.12.1TablevlanIsolationTablenot-accessiblecurrentA table contains configuration of isolated VLAN.
1.3.6.1.4.1.6321.1.2.3.1.10.12.1.1RowvlanIsolationEntrynot-accessiblecurrentAn entry of vlanIsolationTable.
1.3.6.1.4.1.6321.1.2.3.1.10.12.1.1.1ColumnvlanIsolationRowStatusread-createcurrentRow status of the table used to create/delete an entry.
1.3.6.1.4.1.6321.1.2.3.1.10.13NodeenetMtu
1.3.6.1.4.1.6321.1.2.3.1.10.13.1ScalarenetMtuEntryread-writecurrentSets the MTU size for layer 2 frame, size from 1526 to 1532, default value is 1526.
1.3.6.1.4.1.6321.1.2.3.1.10.51Nodedhcp
1.3.6.1.4.1.6321.1.2.3.1.10.51.2TabledhcpRelay82Tablenot-accessiblecurrentA table that contains DHCP Relay configuration.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1RowdhcpRelay82Entrynot-accessiblecurrentThe entry of DHCP Relay table.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.1ColumndhcpRelay82PrimaryServerread-writecurrentThe IP address of the DHCP Relay primary server.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.2ColumndhcpRelay82SecondaryServerread-writecurrentThe IP address of the DHCP Relay secondary server.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.3ColumndhcpRelay82ActiveServerread-onlycurrentThe current active DHCP Relay server.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.4ColumndhcpRelay82Enableread-createcurrentEnable/disable DHCP relay and Option82 function.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.5ColumndhcpRelay82Inforead-createcurrentUser specific Option82 information.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.6ColumndhcpRelay82RelayModeread-createcurrentDHCP relay mode.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.8ColumndhcpRelay82Suboption2Enableread-createcurrentEnable/disable Option 82 sub-option 2.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.9ColumndhcpRelay82Suboption2Inforead-createcurrentUser specified information for Option 82 sub-option 2.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.10ColumndhcpRelay82EntryEnableread-createcurrentEnable/disable DHCP Relay
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.11ColumndhcpRelay82EntryOptionModeread-createcurrentOption82 format.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.12ColumndhcpRelay82VlanIpread-writecurrentThe IP address of the DHCP Relay interface for this VLAN.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.13ColumndhcpRelay82VlanMaskread-writecurrentThe network mask of the DHCP Relay interface for this VLAN.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.14ColumndhcpRelay82VlanGatewayread-writecurrentThe gateway of the DHCP Relay interface for this VLAN.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.15ColumndhcpRelay82ThirdServerread-writecurrentThe IP address of the DHCP Relay third server.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.16ColumndhcpRelay82FourthServerread-writecurrentThe IP address of the DHCP Relay fourth server.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.17ColumndhcpRelay82FifthServerread-writecurrentThe IP address of the DHCP Relay fifth server.
1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.18ColumndhcpRelay82ServerVidread-writecurrentThe VID of the DHCP Relay server for this VLAN.
1.3.6.1.4.1.6321.1.2.3.1.10.51.8NodedhcpRelayTest
1.3.6.1.4.1.6321.1.2.3.1.10.51.8.1ScalardhcpRelayTestVidread-writecurrentSetting the VID of the test server.
1.3.6.1.4.1.6321.1.2.3.1.10.51.8.2ScalardhcpRelayTestIpread-writecurrentSetting the IP of the test server.
1.3.6.1.4.1.6321.1.2.3.1.10.51.8.3ScalardhcpRelayTestOpsread-writecurrentSet the object to 1 to test DHCP server.
1.3.6.1.4.1.6321.1.2.3.1.10.51.8.4ScalardhcpRelayTestStatusread-onlycurrentDisplay testing server status.
1.3.6.1.4.1.6321.1.2.3.1.10.51.9NodedhcpRelayArp
1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1TabledhcpRelayArpShowTablenot-accessiblecurrentThe table displays DHCP ARP.
1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1RowdhcpRelayArpShowEntrynot-accessiblecurrentAn entry of dhcpRelayArpShowTable.
1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1.1ColumndhcpRelayArpShowVidread-onlycurrentDisplay the VID of the DHCP ARP entry.
1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1.2ColumndhcpRelayArpShowIpread-onlycurrentDisplay the IP of the DHCP ARP entry.
1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1.3ColumndhcpRelayArpShowMacread-onlycurrentDisplay the MAC of the DHCP ARP entry.
1.3.6.1.4.1.6321.1.2.3.1.10.51.9.2ScalardhcpRelayArpFlushOpsread-writecurrentSet the object to 1 to start flushing.
1.3.6.1.4.1.6321.1.2.3.1.10.53Nodemacfilter
1.3.6.1.4.1.6321.1.2.3.1.10.53.1TablemacFilterPortTablenot-accessiblecurrentThis table includes the status of mac filtering for each port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1RowmacFilterPortEntrynot-accessiblecurrentAn entry in macFilterPortTable.
1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1.1ColumnmacFilterPortEnableread-writecurrentEnable/disable MAC filtering for the port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1.2ColumnmacFilterPortMacCountread-writecurrentThe total number of MAC addresses allowed for the port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1.3ColumnmacFilterPortFilterModeread-writecurrentThe mac filter mode (accept or deny) for the port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.2ScalarmaxNumOfMacFiltersInSystemread-onlycurrentThe max number of mac filters supported in the system.
1.3.6.1.4.1.6321.1.2.3.1.10.53.3ScalarmaxNumOfMacFiltersPerPortread-onlycurrentThe max number of mac filters supported per port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.4ScalarcurrNumOfMacFiltersInSystemread-onlycurrentThe current number of mac filters in the system.
1.3.6.1.4.1.6321.1.2.3.1.10.53.5TablemacFilterTablenot-accessiblecurrentA table that contains the mac filter addresses.
1.3.6.1.4.1.6321.1.2.3.1.10.53.5.1RowmacFilterEntrynot-accessiblecurrentThe entry of macFilterTable.
1.3.6.1.4.1.6321.1.2.3.1.10.53.5.1.1ColumnmacFilterAddrread-onlycurrentThe mac address which can pass through or be rejected from the port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.5.1.2ColumnmacFilterRowStatusread-createcurrentThe row status of the entry.
1.3.6.1.4.1.6321.1.2.3.1.10.53.6NodemacfilterBatchSet
1.3.6.1.4.1.6321.1.2.3.1.10.53.6.1ScalarmacfilterTargetread-writecurrentThis managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: 0, Reserved(chassis)…
1.3.6.1.4.1.6321.1.2.3.1.10.53.6.2ScalarmacfilterOpsread-writecurrentThe corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: enable mac filter BIT 2: enable mac count filter BIT 3: disable…
1.3.6.1.4.1.6321.1.2.3.1.10.53.6.3ScalarmacFilterMacCountForBatchSetread-writecurrentThe total number of MAC addresses allowed for a port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.7TableouiFilterTableOldnot-accessiblecurrentA table that contains the OUI filter addresses.
1.3.6.1.4.1.6321.1.2.3.1.10.53.7.1RowouiFilterEntryOldnot-accessiblecurrentThe entry of ouiFilterTableOld.
1.3.6.1.4.1.6321.1.2.3.1.10.53.7.1.1ColumnouiFilterAddrOldread-onlycurrentThe first three bytes of the mac address which can pass through or be rejected from the port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.7.1.2ColumnouiFilterRowStatusOldread-createcurrentThe row status of the entry.
1.3.6.1.4.1.6321.1.2.3.1.10.53.8ScalarmaxNumOfOuiFiltersPerPortread-onlycurrentThe max number of OUI filters supported per port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.9TableouiFilterPortTablenot-accessiblecurrentThis table includes the status of oui filtering for each port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.9.1RowouiFilterPortEntrynot-accessiblecurrentAn entry in macFilterPortTable.
1.3.6.1.4.1.6321.1.2.3.1.10.53.9.1.1ColumnouiFilterPortEnableread-writecurrentEnable/disable oui filtering for the port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.9.1.2ColumnouiFilterPortFilterModeread-writecurrentThe oui filter mode (accept or deny) for the port.
1.3.6.1.4.1.6321.1.2.3.1.10.53.10ScalarmaxNumOfOuiFiltersInSystemread-onlycurrentThe max number of OUI filters supported in system.
1.3.6.1.4.1.6321.1.2.3.1.10.53.11ScalarmaxNumOfOuiFiltersPerVlanread-onlycurrentThe max number of OUI filters supported per vlan.
1.3.6.1.4.1.6321.1.2.3.1.10.53.12TableouiFilterTablenot-accessiblecurrentA table that contains the OUI filter addresses.
1.3.6.1.4.1.6321.1.2.3.1.10.53.12.1RowouiFilterEntrynot-accessiblecurrentThe entry of ouiFilterTable.
1.3.6.1.4.1.6321.1.2.3.1.10.53.12.1.1ColumnouiFilterAddrread-onlycurrentThe first three bytes of the mac address which can pass through or be rejected from the vlan.
1.3.6.1.4.1.6321.1.2.3.1.10.53.12.1.2ColumnouiFilterRowStatusread-createcurrentThe row status of the entry.
1.3.6.1.4.1.6321.1.2.3.1.10.53.13TableouiFilterVlanTablenot-accessiblecurrentThis table includes the status of oui filtering for each configured VLAN.
1.3.6.1.4.1.6321.1.2.3.1.10.53.13.1RowouiFilterVlanEntrynot-accessiblecurrentAn entry in ouiFilterVlanTable.
1.3.6.1.4.1.6321.1.2.3.1.10.53.13.1.1ColumnouiFilterVlanEnableread-writecurrentEnable/disable oui filtering for the VLAN.
1.3.6.1.4.1.6321.1.2.3.1.10.53.13.1.2ColumnouiFilterVlanFilterModeread-writecurrentThe oui filter mode (accept or deny) for the VLAN.
1.3.6.1.4.1.6321.1.2.3.1.10.55NodedhcpSnoop
1.3.6.1.4.1.6321.1.2.3.1.10.55.1TabledhcpSnoopPortTablenot-accessiblecurrentThis table includes DHCP snooping enable/disable for each port.
1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1RowdhcpSnoopPortEntrynot-accessiblecurrentAn entry of dhcpSnoopPortTable.
1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1.1ColumndhcpSnoopEnableread-writecurrentEnable/disable DHCP snooping for a port.
1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1.2ColumndhcpSnoopMaxcntread-writecurrentSet the max entries of the DHCP ARP table.
1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1.3ColumndhcpSnoopSmacverifyEnableread-writecurrentEnable/disable DHCP source MAC verify for a port.
1.3.6.1.4.1.6321.1.2.3.1.10.55.2ScalardhcpSnoopTargetread-writecurrentThis managed object is used for identify the target on which the operation should be performed. The target is encoded as: Byte 1: the octet specifies a set of …
1.3.6.1.4.1.6321.1.2.3.1.10.55.3ScalardhcpSnoopOpsread-writecurrentThe corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: DHCP snooping table flush.
1.3.6.1.4.1.6321.1.2.3.1.10.55.4TabledhcpStaticTablenot-accessiblecurrentThis table defines DHCP static IP addresses.
1.3.6.1.4.1.6321.1.2.3.1.10.55.4.1RowdhcpStaticEntrynot-accessiblecurrentAn entry of dhcpStaticTable.
1.3.6.1.4.1.6321.1.2.3.1.10.55.4.1.1ColumndhcpStaticIpAddrread-onlycurrentThe IP address which can pass through the port.
1.3.6.1.4.1.6321.1.2.3.1.10.55.4.1.2ColumndhcpStaticRowStatusread-createcurrentRow status of the table entry.
1.3.6.1.4.1.6321.1.2.3.1.10.55.5ScalarmaxNumOfDhcpStaticIpread-onlycurrentThe maximum number of DHCP static IP addresses which can be created for a port.
1.3.6.1.4.1.6321.1.2.3.1.10.55.6ScalardhcpSnoopMaxcntModeread-writecurrentWhen DHCP snooping table is full, new DHCP lease will replace first one in option 0 or will be dropped in option 1.
1.3.6.1.4.1.6321.1.2.3.1.10.56Nodeacl
1.3.6.1.4.1.6321.1.2.3.1.10.56.1TableaclSetTablenot-accessiblecurrentaclsetTable.
1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1RowaclSetEntrynot-accessiblecurrentAn entry of aclSetTable.
1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.1ColumnaclSetVpiread-onlycurrentVPI value
1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.2ColumnaclSetVciread-onlycurrentVCI value
1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.3ColumnaclSetProfileNameread-onlycurrentACL Profile name
1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.4ColumnaclSetRowStatusread-writecurrentRowStatus of aclSetEntry
1.3.6.1.4.1.6321.1.2.3.1.10.56.2TableaclProfileTablenot-accessiblecurrentaclProfileTable.
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1RowaclProfileEntrynot-accessiblecurrentAn entry of aclProfileTable.
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.1ColumnaclProfileRuleNameread-onlycurrentProfile rule name
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.2ColumnaclProfileRuleNumberread-writecurrentThe managed object is for acl profile rule configuration. etype <etype> vlan <vid> (1), etype <etype> smac <mac> (2), etype <etype> dmac <mac> (3), vlan <vid> …
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.3ColumnaclProfileActionNumberread-writecurrentProfile action number. Bit 1: rate Bit 2: rvlan Bit 3: rpri Bit 4: deny Bit 1, Bit 2 & Bit 3 can multiple selection.
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.4ColumnaclProfileRuleParamMaskread-writecurrentProfile rule parameter mask. BIT 1: srcip <ip>/<mask> BIT 2: dstip <ip>/<mask> BIT 3: tos <stos> <etos> BIT 4: srcport <sport> <eport> BIT 5: dstport <sport> <…
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.5ColumnaclProfileRuleEtyperead-writecurrentProfile rule etype
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.6ColumnaclProfileRuleVidread-writecurrentProfile rule vid
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.7ColumnaclProfileRuleSmacread-writecurrentProfile rule source MAC
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.8ColumnaclProfileRuleDmacread-writecurrentProfile rule destination MAC
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.9ColumnaclProfileRulePriorityread-writecurrentProfile rule priority
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.10ColumnaclProfileRuleProtocolread-writecurrentProfile rule protocol. icmp(1),igmp(2),ip(4),tcp(6), udp(17),gre(47),ospf(89), other ptype
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.11ColumnaclProfileRuleSrcIPread-writecurrentProfile rule source IP
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.12ColumnaclProfileRuleSrcIPMaskread-writecurrentThe subnet mask of source IP mask
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.13ColumnaclProfileRuleDestIPread-writecurrentProfile rule source IP
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.14ColumnaclProfileRuleDestIPMaskread-writecurrentThe subnet mask of dest IP mask
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.15ColumnaclProfileRuleStartTosread-writecurrentProfile rule start type of service
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.16ColumnaclProfileRuleEndTosread-writecurrentProfile rule end type of service
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.17ColumnaclProfileRuleSrcStartPortread-writecurrentProfile rule source start port
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.18ColumnaclProfileRuleSrcEndPortread-writecurrentProfile rule source end port
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.19ColumnaclProfileRuleDestStartPortread-writecurrentProfile rule destination start port
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.20ColumnaclProfileRuleDestEndPortread-writecurrentProfile rule destination end port
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.21ColumnaclProfileActionRateread-writecurrentProfile action to replace to this rate
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.22ColumnaclProfileActionrvlanread-writecurrentProfile action to replace to this vlan
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.23ColumnaclProfileActionrpriread-writecurrentProfile action to replace to this priority
1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.24ColumnaclProfileRowStatusread-writecurrentThe row status of the entry.
1.3.6.1.4.1.6321.1.2.3.1.10.57NodepppoeAgent
1.3.6.1.4.1.6321.1.2.3.1.10.57.1TablepppoeAgentTablenot-accessiblecurrentA table that contains PPPoE DHCP Relay configuration.
1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1RowpppoeAgentEntrynot-accessiblecurrentAn entry of pppoeAgentTable.
1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.1ColumnpppoeAgentEnableread-createcurrentEnable/disable DHCP relay and Option82 function.
1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.2ColumnpppoeAgentInforead-createcurrentUser specific Option82 information.
1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.3ColumnpppoeAgentRowStatusread-createcurrentRow status of the table entry.
1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.4ColumnpppoeAgentOptionModeread-createcurrentOption82 format.
1.3.6.1.4.1.6321.1.2.3.1.10.57.2ScalarmaxNumOfPppoeDhcpRelay82Confread-onlycurrentThe maximum number of rows that can be created in pppoeAgentTable.
1.3.6.1.4.1.6321.1.2.3.1.10.60Nodemacff
1.3.6.1.4.1.6321.1.2.3.1.10.60.1TablemacFfTablenot-accessiblecurrentA table that contains MAC Force Forwarding configuration.
1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1RowmacFfEntrynot-accessiblecurrentAn entry of macFfTable.
1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.1ColumnmacFfIndexread-onlycurrentIndex of the MACFF.
1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.2ColumnmacFfVidread-writecurrentThe VLAN-ID refering to this AR/AS.
1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.3ColumnmacFfArIPread-writecurrentIP of this AR/AS
1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.4ColumnmacFfSrcIPread-writecurrentThe source IP address of the MACFF.
1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.5ColumnmacFfSrcMaskread-writecurrentThe subnet mask of source IP mask.
1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.6ColumnmacFfRowStatusread-createcurrentThe row status of the MacFfEntry entry.
1.3.6.1.4.1.6321.1.2.3.1.10.60.3ScalarmacFfArpFlushread-writecurrentSet the object to 1 to flush mac table.
1.3.6.1.4.1.6321.1.2.3.1.10.60.4ScalarmaxNumOfMacFfVlanInSystemread-onlycurrentThe max number of macff Vlans supported in the system.
1.3.6.1.4.1.6321.1.2.3.1.10.60.5TablemacFfVlanTablenot-accessiblecurrentA table that contains MAC Force Forwarding Vlan configuration.
1.3.6.1.4.1.6321.1.2.3.1.10.60.5.1RowmacFfVlanEntrynot-accessiblecurrentAn entry of macFfVlanTable.
1.3.6.1.4.1.6321.1.2.3.1.10.60.5.1.1ColumnmacFfVlanRowstatusread-createcurrentRow status of the table used to create/delete an entry.
1.3.6.1.4.1.6321.1.2.3.1.10.60.5.1.2ColumnmacFfVlanUnknownUnicastread-createcurrentSetting downstream unknown uni-cast packet on macff vlan to flooding or dropping.
1.3.6.1.4.1.6321.1.2.3.1.10.60.6TablemacFfStaticIPTablenot-accessiblecurrent
1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1RowmacFfStaticIPEntrynot-accessiblecurrentAn entry of macFfTable.
1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.1ColumnmacFfStaticIPPortread-onlycurrentThe port number, 1 ~ 48.
1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.2ColumnmacFfStaticIPVidread-onlycurrentVLAN ID of the IP range, 1 ~ 4094, the vid should be enable the MACFF function first.
1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.3ColumnmacFfstaticIPread-onlycurrentThe specified IP range.
1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.4ColumnmacFfStaticIPMaskread-onlycurrentMask_bits is 24 .. 32.
1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.5ColumnmacFfStaticIPRowStatusread-createcurrentThe row status used to configure the table entry.
1.3.6.1.4.1.6321.1.2.3.1.11Nodesys
1.3.6.1.4.1.6321.1.2.3.1.11.5NodeaccessCtrl
1.3.6.1.4.1.6321.1.2.3.1.11.5.2TablesecuredClientTablenot-accessiblecurrentA table that contains information about secured clients.
1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1RowsecuredClientEntrynot-accessiblecurrentA list of secured client entry.
1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.1ColumnsecuredClientIndexread-onlycurrentThe index of the entry.
1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.2ColumnsecuredClientStartIpread-writecurrentThe starting IP address of the secured client set.
1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.3ColumnsecuredClientEndIpread-writecurrentThe ending IP address of the secured client set.
1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.4ColumnsecuredClientServiceread-writecurrentEach bit corresponds to a service. The bit is set to 1 if the service is enabled, and set to 0 if the service is disabled. The various bit positions are: BIT 1…
1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.5ColumnsecuredClientEnableread-writecurrentEnable/disable the entry.
1.3.6.1.4.1.6321.1.2.3.1.11.8NodeextAlarm
1.3.6.1.4.1.6321.1.2.3.1.11.8.1TableextAlarmTablenot-accessiblecurrentA table that contains external alarm information.
1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1RowextAlarmEntrynot-accessiblecurrentThe entry of external alarm table.
1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.1ColumnextAlarmIndexread-onlycurrentThe index of the entry.
1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.2ColumnextAlarmnameread-writecurrentThe external alarm name.
1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.3ColumnextAlarmstatusread-onlycurrentDispaly 'Normal' or 'Alarm' string
1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.4ColumnextAlarmTriggeredModeread-writecurrentThe external alarm triggered mode.
1.3.6.1.4.1.6321.1.2.3.1.11.9Nodeuser
1.3.6.1.4.1.6321.1.2.3.1.11.9.1ScalaruserAuthModeread-writecurrentUser authentication procsssing mode.
1.3.6.1.4.1.6321.1.2.3.1.11.9.2ScalaruserAuthServerIpread-writecurrentThe IP address of the authentication server.
1.3.6.1.4.1.6321.1.2.3.1.11.9.3ScalaruserAuthServerPortread-writecurrentThe port of the authentication server.
1.3.6.1.4.1.6321.1.2.3.1.11.9.4ScalaruserAuthServerSecretread-writecurrentThe secret between the authentication server and the NE for authentication process.
1.3.6.1.4.1.6321.1.2.3.1.11.9.5TableuserTablenot-accessiblecurrentA table that contains user information.
1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1RowuserEntrynot-accessiblecurrentAn entry of userTable.
1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.1ColumnuserNameread-onlycurrentThe user name.
1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.2ColumnuserPasswordread-createcurrentThe user password.
1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.3ColumnuserPriviledgeread-createcurrentThe user priviledge to decide what operation the user can and cannot do.
1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.4ColumnuserRowStatusread-createcurrentThe row status used to create or delete a user.
1.3.6.1.4.1.6321.1.2.3.1.11.9.6ScalaruserAuthDefaultPriviledgeread-writecurrentThe user default priviledge to be assigned when radius authentication succeds but no user priviledge information(radius service-type) is provided.
1.3.6.1.4.1.6321.1.2.3.1.11.10NodeusbCastCtrl
1.3.6.1.4.1.6321.1.2.3.1.11.10.1ScalarusBcastCtrlEnableread-writecurrentEnable/disable upstream broadcast control.
1.3.6.1.4.1.6321.1.2.3.1.11.10.2ScalarusBcastCtrlRateread-writecurrent32~49984 in step of 32kbps
1.3.6.1.4.1.6321.1.2.3.1.11.11NodedsbCastCtrl
1.3.6.1.4.1.6321.1.2.3.1.11.11.1ScalardsBcastCtrlEnableread-writecurrentEnable/disable downstream broadcast control.
1.3.6.1.4.1.6321.1.2.3.1.11.11.2ScalardsBcastCtrlRateread-writecurrent32~1000000 in step of 32 kbps
1.3.6.1.4.1.6321.1.2.3.1.11.12ScalarstdioTimeoutread-writecurrentSet the CLI/TELNET/WEB Session timeout, 0, or 1~300 minutes, 0 => disable.
1.3.6.1.4.1.6321.1.2.3.1.11.13ScalarisConfigChangedread-onlycurrentIf system configuration has been changed.
1.3.6.1.4.1.6321.1.2.3.1.11.14NodefwUpgrade
1.3.6.1.4.1.6321.1.2.3.1.11.14.1ScalarfwUpgradeVersionread-writecurrentConfigure the target firmware version that will be upgraded.
1.3.6.1.4.1.6321.1.2.3.1.11.14.2ScalarfwUpgradeCheckread-writecurrentEnable/disable firmware upgrade version checking feature.
1.3.6.1.4.1.6321.1.2.3.1.11.14.3ScalarfwUpgradeStatusread-onlycurrentDisplay current firmware upgrade status.
1.3.6.1.4.1.6321.1.2.3.1.11.15NodedelayedReboot
1.3.6.1.4.1.6321.1.2.3.1.11.15.1ScalardelayedRebootTimerread-writecurrent5~1800 secs, 0: reboot immediately.
1.3.6.1.4.1.6321.1.2.3.1.11.15.2ScalardelayedRebootRemainingTimeread-onlycurrentDisplay the remaining time of scheduled reboot.
1.3.6.1.4.1.6321.1.2.3.1.11.15.3ScalardelayedRebootCancelread-writecurrentcancel the scheduled reboot.
1.3.6.1.4.1.6321.1.2.3.1.12Nodetrap
1.3.6.1.4.1.6321.1.2.3.1.13Nodestatistics
1.3.6.1.4.1.6321.1.2.3.1.13.1ScalarigmpQueryCntTotalread-onlycurrentThe total number of IGMP query messages received.
1.3.6.1.4.1.6321.1.2.3.1.13.2ScalarigmpReportCntTotalread-onlycurrentThe total number of IGMP report messages received.
1.3.6.1.4.1.6321.1.2.3.1.13.3ScalarigmpLeaveCntTotalread-onlycurrentThe total number of IGMP leave messages received.
1.3.6.1.4.1.6321.1.2.3.1.13.4ScalarigmpNumOfActiveGroupsread-onlycurrentThe total number of IGMP learned groups.
1.3.6.1.4.1.6321.1.2.3.1.13.5TableigmpGroupTablenot-accessiblecurrentThis table includes igmp group information.
1.3.6.1.4.1.6321.1.2.3.1.13.5.1RowigmpGroupEntrynot-accessiblecurrentAn entry in igmpGroupTable.
1.3.6.1.4.1.6321.1.2.3.1.13.5.1.1ColumnigmpGroupIpread-onlycurrentigmp group IP
1.3.6.1.4.1.6321.1.2.3.1.13.5.1.2ColumnigmpGroupvidread-onlycurrentvlan id
1.3.6.1.4.1.6321.1.2.3.1.13.5.1.3ColumnigmpGroupnumberOfMembersread-onlycurrentnumber Of Members
1.3.6.1.4.1.6321.1.2.3.1.13.5.1.4ColumnigmpGroupMemberPortsread-onlycurrentGroup Member Ports
1.3.6.1.4.1.6321.1.2.3.1.13.6TableigmpGroupPortTablenot-accessiblecurrentThis table includes igmp Group port information.
1.3.6.1.4.1.6321.1.2.3.1.13.6.1RowigmpGroupPortEntrynot-accessiblecurrentAn entry in igmpGroupPortTable.
1.3.6.1.4.1.6321.1.2.3.1.13.6.1.1ColumnigmpGroupPortIpread-onlycurrentIgmp Group IP
1.3.6.1.4.1.6321.1.2.3.1.13.6.1.2ColumnigmpGroupPortvidread-onlycurrentIgmp Group vid
1.3.6.1.4.1.6321.1.2.3.1.13.7TableigmpGroupV2Tablenot-accessiblecurrentA table that displays IGMP learned group member information.
1.3.6.1.4.1.6321.1.2.3.1.13.7.1RowigmpGroupV2Entrynot-accessiblecurrentAn entry of igmpGroupV2Table.
1.3.6.1.4.1.6321.1.2.3.1.13.7.1.1ColumnigmpGroupV2Vidread-onlycurrentThe IGMP group VLAN ID.
1.3.6.1.4.1.6321.1.2.3.1.13.7.1.2ColumnigmpGroupV2Ipread-onlycurrentThe multicast IP address.
1.3.6.1.4.1.6321.1.2.3.1.13.7.1.3ColumnigmpGroupV2NumOfMembersread-onlycurrentThe number of member ports in the group.
1.3.6.1.4.1.6321.1.2.3.1.13.7.1.4ColumnigmpGroupV2MemberPortsread-onlycurrentThe member port list of the group.
1.3.6.1.4.1.6321.1.2.3.1.13.8TableigmpGroupPortV2Tablenot-accessiblecurrentA table that displays IGMP joined groups in this port.
1.3.6.1.4.1.6321.1.2.3.1.13.8.1RowigmpGroupPortV2Entrynot-accessiblecurrentAn entry of igmpGroupPortV2Table.
1.3.6.1.4.1.6321.1.2.3.1.13.8.1.1ColumnigmpGroupPortV2Vidread-onlycurrentThe IGMP group VLAN ID.
1.3.6.1.4.1.6321.1.2.3.1.13.8.1.2ColumnigmpGroupPortV2Ipread-onlycurrentThe multicast IP address.
1.3.6.1.4.1.6321.1.2.3.1.13.8.1.3ColumnigmpGroupPortV2SourceIpread-onlycurrentThe source IP address that joins the IGMP group.
1.3.6.1.4.1.6321.1.2.3.1.13.9TableigmpPortCtrlPduTablenot-accessiblecurrentA table that displays IGMP related counter values in this port.
1.3.6.1.4.1.6321.1.2.3.1.13.9.1RowigmpPortCtrlPduEntrynot-accessiblecurrentAn entry of igmpPortCtrlPduTable.
1.3.6.1.4.1.6321.1.2.3.1.13.9.1.1ColumnigmpPortCtrlPduQueryCntread-onlycurrentThe total number of IGMP query messages received in this port.
1.3.6.1.4.1.6321.1.2.3.1.13.9.1.2ColumnigmpPortCtrlPduReportCntread-onlycurrentThe total number of IGMP report messages received in this port.
1.3.6.1.4.1.6321.1.2.3.1.13.9.1.3ColumnigmpPortCtrlPduLeaveCntread-onlycurrentThe total number of IGMP leave messages received in this port.
1.3.6.1.4.1.6321.1.2.3.1.13.9.1.4ColumnigmpPortNumOfActiveGroupsread-onlycurrentThe total number of active IGMP groups in this port.
1.3.6.1.4.1.6321.1.2.3.1.13.9.1.5ColumnigmpPortCtrlAuditLeaveCntread-onlycurrentThe total number of groups left by audit query.
1.3.6.1.4.1.6321.1.2.3.1.13.11NodedhcpStats
1.3.6.1.4.1.6321.1.2.3.1.13.11.1TabledhcpSnoopIpTablenot-accessiblecurrentThis table shows the IP addresses and netmasks offered by the DHCP server.
1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1RowdhcpSnoopIpEntrynot-accessiblecurrentAn entry of dhcpSnoopIpTable.
1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.1ColumndhcpSnoopIpread-onlycurrentThe snooped IP address.
1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.2ColumndhcpSnoopMacread-onlycurrentThe snooped MAC address.
1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.3ColumndhcpSnoopVidread-onlycurrentThe snooped VLAN ID.
1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.4ColumndhcpSnoopMaskread-onlycurrentThe snooped IP mask
1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.5ColumndhcpSnoopGatewayread-onlycurrentThe snooped Gateway.
1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.6ColumndhcpSnoopRouteMapread-onlycurrentThe refrence bit map of the dhcp route
1.3.6.1.4.1.6321.1.2.3.1.13.11.2TabledhcpSnoopCounterTablenot-accessiblecurrentThis table shows the DHCP statistics.
1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1RowdhcpSnoopCounterEntrynot-accessiblecurrentAn entry of dhcpSnoopCounterTable.
1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.1ColumndhcpDiscoveryread-onlycurrentThe total number of received DHCP server discovery packets.
1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.2ColumndhcpOfferread-onlycurrentThe total number of received DHCP server offer packets.
1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.3ColumndhcpRequestread-onlycurrentThe total number of received DHCP IP request packets.
1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.4ColumndhcpAckread-onlycurrentThe total number of received DHCP IP acknowledge packets.
1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.5ColumndhcpAckBySnoopFullread-onlycurrentThe total number of received DHCP IP acknowledge packets that replace the oldest snooping entry in snooping table due to table full.
1.3.6.1.4.1.6321.1.2.3.1.13.11.3TabledhcpRouteTablenot-accessiblecurrentA table that contains dhcp route information.
1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1RowdhcpRouteEntrynot-accessiblecurrentAn entry of dhcpRouteTable.
1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.1ColumndhcpRouteIndexread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.2ColumndhcpRouteVidread-onlycurrentThe VLAN-ID refering to this dhcp route.
1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.3ColumndhcpRouteIPread-onlycurrentIP of this dhcp route
1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.4ColumndhcpRouteMaskread-onlycurrentThe subnet mask of source IP mask.
1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.5ColumndhcpRouteGwIPread-onlycurrentThe gateway IP address.
1.3.6.1.4.1.6321.1.2.3.1.13.12NodepaepvcStats
1.3.6.1.4.1.6321.1.2.3.1.13.12.1TablepaepvcSessionTablenot-accessiblecurrentThis table shows the paepvc session statistics.
1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1RowpaepvcSessionEntrynot-accessiblecurrentAn entry of paepvcSessionTable.
1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.1ColumnpaepvcSessionVpiread-onlycurrentThe PAEPVC VPI.
1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.2ColumnpaepvcSessionVciread-onlycurrentThe PAEPVC VCI.
1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.3ColumnpaepvcSessionStateread-onlycurrentThe PAEPVC status.
1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.4ColumnpaepvcSessionIdread-onlycurrentThe PAEPVC session ID.
1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.5ColumnpaepvcSessionUptimeread-onlycurrentThe PAEPVC session uptime.
1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.6ColumnpaepvcSessionacnameread-onlycurrentAccess concentrator name.
1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.7ColumnpaepvcSessionsrvcnameread-onlycurrentService name.
1.3.6.1.4.1.6321.1.2.3.1.13.12.2TablepaepvcCountTablenot-accessiblecurrentThis table shows the paepvc counters.
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1RowpaepvcCountEntrynot-accessiblecurrentAn entry of paepvcCountTable.
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.1ColumnpaepvcCountVpiread-onlycurrentThe PAEPVC VPI.
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.2ColumnpaepvcCountVciread-onlycurrentThe PAEPVC VCI.
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.3ColumnpaepvcCountPppLcpCfgReqRxread-onlycurrentThe number of ppp lcp config-request received.
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.4ColumnpaepvcCountPppLcpEchoReqRxread-onlycurrentThe number of ppp lcp echo-request received.
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.5ColumnpaepvcCountPppLcpEchoReplyRxread-onlycurrentThe number of ppp lcp echo-reply received.
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.6ColumnpaepvcCountPadiTxread-onlycurrentThe number of pppoe padi transfered
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.7ColumnpaepvcCountPadoRxread-onlycurrentThe number of pppoe pado received
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.8ColumnpaepvcCountPadrTxread-onlycurrentThe number of pppoe padr transfered
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.9ColumnpaepvcCountPadsRxread-onlycurrentThe number of pppoe pads received
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.10ColumnpaepvcCountPadtTxread-onlycurrentThe number of pppoe padt transfered
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.11ColumnpaepvcCountPadtRxread-onlycurrentThe number of pppoe padt received
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.12ColumnpaepvcCountSrvcnameErrRxread-onlycurrentThe number of pppoe service name error received
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.13ColumnpaepvcCountAcSystemErrRxread-onlycurrentThe number of pppoe access concentrator name error received
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.14ColumnpaepvcCountGenericErrTxread-onlycurrentThe number of pppoe generic error transfered
1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.15ColumnpaepvcCountGenericErrRxread-onlycurrentThe number of pppoe generic error received
1.3.6.1.4.1.6321.1.2.3.1.13.13NodemacStats
1.3.6.1.4.1.6321.1.2.3.1.13.13.1ScalarmacDisplayTargetread-writecurrentThis managed object is a filter used for identify the target from which the MAC addresses are learned in macTable. The target could be: 99: all ports in the sy…
1.3.6.1.4.1.6321.1.2.3.1.13.13.2TablemacTablenot-accessiblecurrentA table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the trans…
1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1RowmacEntrynot-accessiblecurrentAn entry of macTable.
1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1.1ColumnmacAddressread-onlycurrentA unicast MAC address for which the bridge has forwarding and/or filtering information.
1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1.2ColumnmacPortread-onlycurrentThe port from which the mac address has been learned.
1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1.3ColumnmacStatusread-onlycurrentThe status of this entry.
1.3.6.1.4.1.6321.1.2.3.1.13.14NodeipbpvcStats
1.3.6.1.4.1.6321.1.2.3.1.13.14.1TablearpproxyTablenot-accessiblecurrentDisplay ARP table. This table is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1RowarpproxyEntrynot-accessiblecurrentAn entry of arpproxyTable.
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.1ColumnarpproxyIpread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.2ColumnarpproxyMacread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.3ColumnarpproxyIfIndexread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.4ColumnarpproxyVpiread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.5ColumnarpproxyVciread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.6ColumnarpproxyInterfaceIpread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.7ColumnarpproxyInterfaceMaskread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.8ColumnarpproxyInterfaceVidread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.9ColumnarpproxyDhcpIpread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.10ColumnarpproxyTyperead-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.2TableipbpvcIfDynamicTablenot-accessiblecurrentDisplay runtime interfaces. This table is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1RowipbpvcIfDynamicEntrynot-accessiblecurrentAn entry of ipbpvcIfDynamicTable.
1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.1ColumnipbpvcIfDynamicIpread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.2ColumnipbpvcIfDynamicMaskread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.3ColumnipbpvcIfDynamicIfIndexread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.4ColumnipbpvcIfDynamicVpiread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.5ColumnipbpvcIfDynamicVciread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.3TableipbpvcRouteDynamicTablenot-accessiblecurrentDisplay runtime routing table. This table is supported by R3.00 and later versions.
1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1RowipbpvcRouteDynamicEntrynot-accessiblecurrentAn entry of ipbpvcRouteDynamicTable.
1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.1ColumnipbpvcRouteDynamicTyperead-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.2ColumnipbpvcRouteDynamicIpread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.3ColumnipbpvcRouteDynamicMaskread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.4ColumnipbpvcRouteDynamicNextHopread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.5ColumnipbpvcRouteDynamicMetricread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.6ColumnipbpvcRouteDynamicPriorityread-onlycurrent
1.3.6.1.4.1.6321.1.2.3.1.13.16NodemacffStats
1.3.6.1.4.1.6321.1.2.3.1.13.16.1TablemacFfStatsTablenot-accessiblecurrentA table that contains MAC Force Forwarding static configuration and dynamic information.
1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1RowmacFfStatsEntrynot-accessiblecurrentAn entry of macFfStatsTable.
1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.1ColumnmacFfStatsIndexread-onlycurrentIndex of the MACFF.
1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.2ColumnmacFfStatsVidread-onlycurrentThe VLAN-ID refering to this AR/AS.
1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.3ColumnmacFfStatsArIPread-onlycurrentIP of this AR/AS
1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.4ColumnmacFfStatsSrcIPread-onlycurrentThe source IP address of the MACFF.
1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.5ColumnmacFfStatsSrcMaskread-onlycurrentThe subnet mask of source IP mask.
1.3.6.1.4.1.6321.1.2.3.1.13.16.2TablemacFfArpTablenot-accessiblecurrentA table that contains MAC Force Forwarding ARP information.
1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1RowmacFfArpEntrynot-accessiblecurrentAn entry of macFfArpTable.
1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.1ColumnmacFfArpVidread-onlycurrentThe VLAN-ID refering to this AR/AS.
1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.2ColumnmacFfArpIPread-onlycurrentIP of this AR/AS.
1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.3ColumnmacFfArpPortread-onlycurrentPort of this AR/AS.
1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.4ColumnmacFfArpMacread-onlycurrentMAC address of the AR or AS.
1.3.6.1.4.1.6321.1.2.3.1.13.16.3TablemacFfArpCounterTablenot-accessiblecurrentA table that contains MAC Force Forwarding ARP counter information.
1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1RowmacFfArpCounterEntrynot-accessiblecurrentAn entry of macFfArpCounterTable.
1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.1ColumnmacFfArpCounterRequestTXread-onlycurrentARP Request TX counter.
1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.2ColumnmacFfArpCounterRequestRXread-onlycurrentARP Request RX counter.
1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.3ColumnmacFfArpCounterRequestRXDropread-onlycurrentARP Request RX drop counter.
1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.4ColumnmacFfArpCounterReplyTXread-onlycurrentARP Reply TX counter.
1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.5ColumnmacFfArpCounterReplyRXread-onlycurrentARP Reply RX counter.
1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.6ColumnmacFfArpCounterReplyRXDropread-onlycurrentARP Reply RX drop counter.
1.3.6.1.4.1.6321.1.2.3.1.13.17NodeenetStats
1.3.6.1.4.1.6321.1.2.3.1.13.17.2TableenetSfpInfoTablenot-accessiblecurrentThis table includes sfp info of enet port.
1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1RowenetSfpInfoEntrynot-accessiblecurrentAn entry in enetSfpInfoTable.
1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.1ColumnenetSfpInfoTxpowerread-onlycurrentMeasured Tx Output Power.
1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.2ColumnenetSfpInfoRxpowerread-onlycurrentMeasured Rx Output Power.
1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.3ColumnenetSfpInfoTemperatureread-onlycurrentMeasured temperature.
1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.4ColumnenetSfpInfoTxBiasread-onlycurrentMeasured tx bias.
1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.5ColumnenetSfpInfoVoltageread-onlycurrentMeasured voltage.
1.3.6.1.4.1.6321.1.2.3.1.13.18NodeadslStats
1.3.6.1.4.1.6321.1.2.3.1.13.18.1TableadslPortUtilTablenot-accessiblecurrentThis table includes adsl port utilization.
1.3.6.1.4.1.6321.1.2.3.1.13.18.1.1RowadslPortUtilEntrynot-accessiblecurrentAn entry in adslPortUtilEntry.
1.3.6.1.4.1.6321.1.2.3.1.13.18.1.1.1ColumnadslPortUtilTxread-onlycurrentMeasure adsl port's tx utilization.
1.3.6.1.4.1.6321.1.2.3.1.13.18.1.1.2ColumnadslPortUtilRxread-onlycurrentMeasure adsl port's rx utilization.
1.3.6.1.4.1.6321.1.2.3.1.14Nodeclear
1.3.6.1.4.1.6321.1.2.3.1.14.1ScalarcounterClearTargetread-writecurrentThis managed object is used for identify the target on which the counter would be cleared. The target is encoded as: Byte 1: reserved Byte 2~3: reserved Byte 4…
1.3.6.1.4.1.6321.1.2.3.1.14.2ScalarcounterClearOpsread-writecurrentThe corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: clear interface counters BIT 2: clear pvc packet counters BIT 3…
1.3.6.1.4.1.6321.1.2.3.1.14.3ScalarcounterClearVpiread-writecurrentVPI of the pvc whose counters would be cleared.
1.3.6.1.4.1.6321.1.2.3.1.14.4ScalarcounterClearVciread-writecurrentVCI of the pvc whose counters would be cleared.
1.3.6.1.4.1.6321.1.2.3.1.97NodeaesSeriesCommon
1.3.6.1.4.1.6321.1.2.3.1.98NodeiesSeriesCommon
1.3.6.1.4.1.6321.1.2.3.1.99NodeaccessSwitchCommonATM
MIB Viewer