EGRESSACL-MIB
193 objects
The structure of Egress Access Control List information for the proprietary enterprise.
Imported Objects
| DLINK-ID-REC-MIB | dlink-common-mgmt |
| IPV6-TC | Ipv6Address |
| Q-BRIDGE-MIB | PortList VlanIdOrNone |
| RFC1213-MIB | DisplayString |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-SMI | Counter32 Counter64 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | MacAddress RowStatus |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.171.12.89 | IdentityswEgressAclMgmtMIB | The structure of Egress Access Control List information for the proprietary enterprise. | ||
| 1.3.6.1.4.1.171.12.89.1 | NodeswEgressAclInfo | |||
| 1.3.6.1.4.1.171.12.89.1.1 | ScalarswEgressACLTotalUsedRuleEntries | read-only | current | The total number of used egress ACL rule entries. |
| 1.3.6.1.4.1.171.12.89.1.2 | ScalarswEgressACLTotalUnusedRuleEntries | read-only | current | The total number of unused egress ACL rule entries. |
| 1.3.6.1.4.1.171.12.89.2 | NodeswEgressAclMaskMgmt | |||
| 1.3.6.1.4.1.171.12.89.2.1 | TableswEgressACLEthernetTable | not-accessible | current | This table contains egress ACL mask Ethernet information. The access profile will be created on the switch to define which part of each outgoing frame's layer … |
| 1.3.6.1.4.1.171.12.89.2.1.1 | RowswEgressACLEthernetEntry | not-accessible | current | A list of information about the egress ACL for Ethernet. |
| 1.3.6.1.4.1.171.12.89.2.1.1.1 | ColumnswEgressACLEthernetProfileID | not-accessible | current | The ID of the egress ACL mask entry unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.89.2.1.1.2 | ColumnswEgressACLEthernetRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.89.2.1.1.3 | ColumnswEgressACLEthernetProfileName | read-create | current | The name of the egress ACL mask entry unique to the mask list. |
| 1.3.6.1.4.1.171.12.89.2.1.1.4 | ColumnswEgressACLEthernetUsevlan | read-create | current | Specifies that the switch will examine the VLAN part of each packet header. |
| 1.3.6.1.4.1.171.12.89.2.1.1.5 | ColumnswEgressACLEthernetVlanMask | read-create | current | The mask used for the VLAN ID. Valid values are from 0x0000 to 0x0FFF. The default value is 0x0FFF |
| 1.3.6.1.4.1.171.12.89.2.1.1.6 | ColumnswEgressACLEthernetUse8021p | read-create | current | Specifies if the switch will examine the 802.1p priority value in the frame's header or not. |
| 1.3.6.1.4.1.171.12.89.2.1.1.7 | ColumnswEgressACLEthernetUseEthernetType | read-create | current | Specifies if the switch will examine the Ethernet type value in each frame's header or not. |
| 1.3.6.1.4.1.171.12.89.2.1.1.8 | ColumnswEgressACLEthernetMacAddrMaskState | read-create | current | This object indicates the status of the MAC address mask. other (1) - Neither source MAC address nor destination MAC address is masked. dst-mac-addr (2) - Dest… |
| 1.3.6.1.4.1.171.12.89.2.1.1.9 | ColumnswEgressACLEthernetSrcMacAddrMask | read-create | current | This object specifies the MAC address mask for the source MAC address. |
| 1.3.6.1.4.1.171.12.89.2.1.1.10 | ColumnswEgressACLEthernetDstMacAddrMask | read-create | current | This object specifies the MAC address mask for the destination MAC address. |
| 1.3.6.1.4.1.171.12.89.2.1.1.11 | ColumnswEgressACLEthernetUnusedRuleEntries | read-only | current | The number of unused rule entries of this Ethernet profile entry. |
| 1.3.6.1.4.1.171.12.89.2.2 | TableswEgressACLIpTable | not-accessible | current | This table contains the egress ACL mask for IP information. Access profiles will be created on the switch to define which part of the outgoing frame's IP layer… |
| 1.3.6.1.4.1.171.12.89.2.2.1 | RowswEgressACLIpEntry | not-accessible | current | A list of information about the egress ACL of the IP layer. |
| 1.3.6.1.4.1.171.12.89.2.2.1.1 | ColumnswEgressACLIpProfileID | not-accessible | current | The ID of the egress ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.89.2.2.1.2 | ColumnswEgressACLIpRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.89.2.2.1.3 | ColumnswEgressACLIpProfileName | read-create | current | The name of the egress ACL mask entry unique to the mask list. |
| 1.3.6.1.4.1.171.12.89.2.2.1.4 | ColumnswEgressACLIpUsevlan | read-create | current | This object indicates if the IP layer VLAN part is examined or not. |
| 1.3.6.1.4.1.171.12.89.2.2.1.5 | ColumnswEgressACLIpVlanMask | read-create | current | The mask used for the VLAN ID. Valid values are from 0x0000 to 0x0FFF. The default value is 0x0FFF. |
| 1.3.6.1.4.1.171.12.89.2.2.1.6 | ColumnswEgressACLIpIpAddrMaskState | read-create | current | This object indicates the status of IP address mask. other (1) - Neither source IP address nor destination IP address is masked. dst-ip-addr (2) - Destination … |
| 1.3.6.1.4.1.171.12.89.2.2.1.7 | ColumnswEgressACLIpSrcIpAddrMask | read-create | current | This object specifies the IP address mask for the source IP address. |
| 1.3.6.1.4.1.171.12.89.2.2.1.8 | ColumnswEgressACLIpDstIpAddrMask | read-create | current | This object specifies the IP address mask for the destination IP address. |
| 1.3.6.1.4.1.171.12.89.2.2.1.9 | ColumnswEgressACLIpUseDSCP | read-create | current | This object indicates if the DSCP protocol in the packet header is to be examined or not. |
| 1.3.6.1.4.1.171.12.89.2.2.1.10 | ColumnswEgressACLIpUseProtoType | read-create | current | That object indicates which protocol will be examined. |
| 1.3.6.1.4.1.171.12.89.2.2.1.11 | ColumnswEgressACLIpIcmpOption | read-create | current | This object indicates which fields are defined for ICMP. none (1)- Both fields are null. type (2)- Type field identified. code (3)- Code field identified. type… |
| 1.3.6.1.4.1.171.12.89.2.2.1.12 | ColumnswEgressACLIpIgmpOption | read-create | current | Indicates if the IGMP options field is identified or not. |
| 1.3.6.1.4.1.171.12.89.2.2.1.13 | ColumnswEgressACLIpTcpOption | read-create | current | This object indicates the status of the filtered address of TCP. other (1) - Neither source port nor destination port is masked. dst-addr (2) - Packets will be… |
| 1.3.6.1.4.1.171.12.89.2.2.1.14 | ColumnswEgressACLIpUdpOption | read-create | current | This object indicates the status of the filtered address of UDP . other (1) - Neither source port nor destination port is masked. dst-addr (2) - Packets will b… |
| 1.3.6.1.4.1.171.12.89.2.2.1.15 | ColumnswEgressACLIpTCPorUDPSrcPortMask | read-create | current | Specifies a TCP port mask for the source port if swEgressACLIpUseProtoType is TCP Specifies a UDP port mask for the source port if swEgressACLIpUseProtoType is… |
| 1.3.6.1.4.1.171.12.89.2.2.1.16 | ColumnswEgressACLIpTCPorUDPDstPortMask | read-create | current | Specifies a TCP port mask for the destination port if swEgressACLIpUseProtoType is TCP Specifies a UDP port mask for the destination port if swEgressACLIpUsePr… |
| 1.3.6.1.4.1.171.12.89.2.2.1.17 | ColumnswEgressACLIpTCPFlagBit | read-create | current | Specifies a TCP connection flag mask. |
| 1.3.6.1.4.1.171.12.89.2.2.1.18 | ColumnswEgressACLIpTCPFlagBitMask | read-create | current | A value which indicates the set of TCP flags that this entity may potentially offer. The value is a sum of flag bits. This sum initially takes the value zero. … |
| 1.3.6.1.4.1.171.12.89.2.2.1.19 | ColumnswEgressACLIpProtoIDOption | read-create | current | Specifies if the switch will examine each frame's protocol ID field or not. |
| 1.3.6.1.4.1.171.12.89.2.2.1.20 | ColumnswEgressACLIpProtoID | read-create | current | Specifies that the rule applies to the IP protocol ID behind the IP header. |
| 1.3.6.1.4.1.171.12.89.2.2.1.21 | ColumnswEgressACLIpProtoIDMask | read-create | current | Specifies that the rule applies to the IP protocol ID and the mask options behind the IP header. |
| 1.3.6.1.4.1.171.12.89.2.2.1.22 | ColumnswEgressACLIpUnusedRuleEntries | read-only | current | The number of unused rule entries this IP profile entry. |
| 1.3.6.1.4.1.171.12.89.2.3 | TableswEgressACLIpv6MaskTable | not-accessible | current | This table contains IPv6 egress ACL mask information. An access profile will be created on the switch to define which parts of each outgoing frame's IPv6 part … |
| 1.3.6.1.4.1.171.12.89.2.3.1 | RowswEgressACLIpv6MaskEntry | not-accessible | current | A list of information about egress ACL for IPv6. |
| 1.3.6.1.4.1.171.12.89.2.3.1.1 | ColumnswEgressACLIpv6MaskProfileID | not-accessible | current | The ID of the egress ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.89.2.3.1.2 | ColumnswEgressACLIpv6MaskRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.89.2.3.1.3 | ColumnswEgressACLIpv6MaskProfileName | read-create | current | The name of egress ACL mask entry unique to the mask list. |
| 1.3.6.1.4.1.171.12.89.2.3.1.4 | ColumnswEgressACLIpv6MaskClass | read-create | current | This object indicates if the class field in the IPv6 packet header is to be examined or not. |
| 1.3.6.1.4.1.171.12.89.2.3.1.5 | ColumnswEgressACLIpv6IpAddrMaskState | read-create | current | This object indicates the status of the IPv6 address mask. other (1) - Neither source IPv6 address nor destination IPv6 address is masked. dst-ipv6-addr (2) - … |
| 1.3.6.1.4.1.171.12.89.2.3.1.6 | ColumnswEgressACLIpv6MaskSrcIpv6Mask | read-create | current | This object specifies the IPv6 address mask for the source IPv6 address. |
| 1.3.6.1.4.1.171.12.89.2.3.1.7 | ColumnswEgressACLIpv6MaskDstIpv6Mask | read-create | current | This object specifies the IPv6 address mask for the destination IPv6 address. |
| 1.3.6.1.4.1.171.12.89.2.3.1.8 | ColumnswEgressACLIpv6MaskUseProtoType | read-create | current | That object indicates which protocol will be examined. |
| 1.3.6.1.4.1.171.12.89.2.3.1.9 | ColumnswEgressACLIpv6MaskIcmpOption | read-create | current | This object indicates which fields are defined for ICMP. none (1)- Both fields are null. type (2)- Type field identified. code (3)- Code field identified. type… |
| 1.3.6.1.4.1.171.12.89.2.3.1.10 | ColumnswEgressACLIpv6MaskTcpOption | read-create | current | This object indicates the status of the filtered address of TCP. other (1) - Neither source port nor destination port is masked. dst-addr (2) - Packets will be… |
| 1.3.6.1.4.1.171.12.89.2.3.1.11 | ColumnswEgressACLIpv6MaskUdpOption | read-create | current | This object indicates the status of the filtered address of UDP. other (1) - Neither source port nor destination port is masked. dst-addr (2) - Packets will be… |
| 1.3.6.1.4.1.171.12.89.2.3.1.12 | ColumnswEgressACLIpv6MaskTCPorUDPSrcPortMask | read-create | current | Specifies a TCP port mask for the source port if swEgressACLIpv6MaskUseProtoType is TCP Specifies a UDP port mask for the source port if swEgressACLIpv6MaskUse… |
| 1.3.6.1.4.1.171.12.89.2.3.1.13 | ColumnswEgressACLIpv6MaskTCPorUDPDstPortMask | read-create | current | Specifies a TCP port mask for the destination port if swEgressACLIpv6MaskUseProtoType is TCP Specifies a UDP port mask for the destination port if swEgressACLI… |
| 1.3.6.1.4.1.171.12.89.2.3.1.14 | ColumnswEgressACLIpv6MaskUnusedRuleEntries | read-only | current | The number of unused rule entries of this IPv6 profile entry. |
| 1.3.6.1.4.1.171.12.89.2.4 | ScalarswEgressACLMaskDelAllState | read-write | current | Used to delete all egress ACL masks. |
| 1.3.6.1.4.1.171.12.89.3 | NodeswEgressAclRuleMgmt | |||
| 1.3.6.1.4.1.171.12.89.3.1 | TableswEgressACLEtherRuleTable | not-accessible | current | This table contains Ethernet egress ACL information. |
| 1.3.6.1.4.1.171.12.89.3.1.1 | RowswEgressACLEtherRuleEntry | not-accessible | current | A list of information about the egress ACL rule of the layer 2 part of each packet. |
| 1.3.6.1.4.1.171.12.89.3.1.1.1 | ColumnswEgressACLEtherRuleProfileID | not-accessible | current | The ID of the egress ACL rule entry, which is unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.89.3.1.1.2 | ColumnswEgressACLEtherRuleAccessID | not-accessible | current | The ID of the the egress ACL rule entry relates to the swEgressACLEtherRuleProfileID. When row creation is set to 0, this indicates the access ID will be assig… |
| 1.3.6.1.4.1.171.12.89.3.1.1.3 | ColumnswEgressACLEtherRuleRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.89.3.1.1.4 | ColumnswEgressACLEtherRuleMatchVID | read-create | current | Specifies that the access rule will apply only to packets with this VLAN ID. It is applied to the specified ports configured by swEgressACLEtherRulePortGroup. … |
| 1.3.6.1.4.1.171.12.89.3.1.1.5 | ColumnswEgressACLEtherRuleMatchVlanMask | read-create | current | Specifies the per rule mask for the VLAN field as defined in swEgressACLEtherRuleVlan object. The value of this object when not in use is the corresponding mas… |
| 1.3.6.1.4.1.171.12.89.3.1.1.6 | ColumnswEgressACLEtherRuleSrcMacAddress | read-create | current | Specifies that the access rule will apply to only packets with this source MAC address. |
| 1.3.6.1.4.1.171.12.89.3.1.1.7 | ColumnswEgressACLEtherRuleMaskSrcMacAddress | read-create | current | Specifies the per rule mask for the source MAC addres field as defined in swEgressACLEtherRuleSrcMacAddress object. The value of this object when not in use is… |
| 1.3.6.1.4.1.171.12.89.3.1.1.8 | ColumnswEgressACLEtherRuleDstMacAddress | read-create | current | Specifies that the access rule will apply to packets with this destination MAC address. |
| 1.3.6.1.4.1.171.12.89.3.1.1.9 | ColumnswEgressACLEtherRuleMaskDstMacAddress | read-create | current | Specifies the per rule mask for the destination MAC addres field as defined in swEgressACLEtherRuleDstMacAddress object. The value of this object when not in u… |
| 1.3.6.1.4.1.171.12.89.3.1.1.10 | ColumnswEgressACLEtherRule8021P | read-create | current | Specifies that the access rule will apply to packets with this 802.1p priority value. A value of -1 indicates that this object is not active. |
| 1.3.6.1.4.1.171.12.89.3.1.1.11 | ColumnswEgressACLEtherRuleEtherType | read-create | current | Specifies that the access rule will apply to packets with this hexadecimal 802.1Q Ethernet type value in the packet header. |
| 1.3.6.1.4.1.171.12.89.3.1.1.12 | ColumnswEgressACLEtherRuleVID | read-create | current | Specifies the VLAN-based ACL rule. There are two conditions: 1. this rule will apply to all the ports; 2. packets must belong to this VLAN. This object and swE… |
| 1.3.6.1.4.1.171.12.89.3.1.1.13 | ColumnswEgressACLEtherRulePort | read-create | current | Specifies that the access rule will only apply to the port. This object and swEgressACLEtherRuleVID,swEgressACLEtherRulePortGroup can not be set together. When… |
| 1.3.6.1.4.1.171.12.89.3.1.1.14 | ColumnswEgressACLEtherRulePortGroup | read-create | current | Specifies that the access rule will only apply to port(s) which belong to this port group. This object and swEgressACLEtherRuleVID, swEgressACLEtherRulePort ca… |
| 1.3.6.1.4.1.171.12.89.3.1.1.15 | ColumnswEgressACLEtherRulePermit | read-create | current | This object indicates if the result of the packet examination is 'permit' or 'deny'. The default is 'permit'. deny - Specifies that packets matching the access… |
| 1.3.6.1.4.1.171.12.89.3.1.1.16 | ColumnswEgressACLEtherRuleEnableReplacePriority | read-create | current | Specifies if the switch will change priorities of packets that match the access profile 802.1p priority tag field or not . |
| 1.3.6.1.4.1.171.12.89.3.1.1.17 | ColumnswEgressACLEtherRuleReplacePriority | read-create | current | Specifies that the priority will be changed in packets while the swEgressACLEtherRuleEnablePriority is enabled.A value of -1 indicates that this object is not … |
| 1.3.6.1.4.1.171.12.89.3.1.1.18 | ColumnswEgressACLEtherRuleEnableReplaceDscp | read-create | current | Specifies if the switch will change priorities of packets that match the access profile DSCP field or not. |
| 1.3.6.1.4.1.171.12.89.3.1.1.19 | ColumnswEgressACLEtherRuleReplaceDscp | read-create | current | Specifies a value to be written to the DSCP field of an outgoing packet that meets the criteria specified in the first part of the command. This value will ove… |
| 1.3.6.1.4.1.171.12.89.3.1.1.20 | ColumnswEgressAclEtherRuleTimeRangeName | read-create | current | Specifies a name of a time-range associated with a specific egress ACL entry. The time-range name must first be created before being associated with the access… |
| 1.3.6.1.4.1.171.12.89.3.2 | TableswEgressACLIpRuleTable | not-accessible | current | |
| 1.3.6.1.4.1.171.12.89.3.2.1 | RowswEgressACLIpRuleEntry | not-accessible | current | |
| 1.3.6.1.4.1.171.12.89.3.2.1.1 | ColumnswEgressACLIpRuleProfileID | not-accessible | current | The ID of the egress ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.89.3.2.1.2 | ColumnswEgressACLIpRuleAccessID | not-accessible | current | The ID of the egress ACL rule entry relates to the swEgressACLEtherRuleProfileID. When row creation is set to 0, this indicates the access ID will be assigned … |
| 1.3.6.1.4.1.171.12.89.3.2.1.3 | ColumnswEgressACLIpRuleRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.89.3.2.1.4 | ColumnswEgressACLIpRuleMatchVID | read-create | current | Specifies that the access rule will apply only to packets with this VLAN ID. It is applied to the specified ports configured by swEgressACLIpRulePortGroup. Not… |
| 1.3.6.1.4.1.171.12.89.3.2.1.5 | ColumnswEgressACLIpMatchVlanMask | read-create | current | Specifies the per rule mask for the VLAN as defined in swEgressACLIpRuleVlan object. The value of this object when not in use is the corresponding mask in the … |
| 1.3.6.1.4.1.171.12.89.3.2.1.6 | ColumnswEgressACLIpRuleSrcIpaddress | read-create | current | Specifies an IP source address. |
| 1.3.6.1.4.1.171.12.89.3.2.1.7 | ColumnswEgressACLIpRuleMaskSrcIpaddress | read-create | current | Specifies the per rule mask for the source IP address as defined in swEgressACLIpRuleSrcIpaddress object. The value of this object when not in use is the corre… |
| 1.3.6.1.4.1.171.12.89.3.2.1.8 | ColumnswEgressACLIpRuleDstIpaddress | read-create | current | Specifies an IP destination address. |
| 1.3.6.1.4.1.171.12.89.3.2.1.9 | ColumnswEgressACLIpRuleMaskDstIpaddress | read-create | current | Specifies the per rule mask for the destination IP address as defined in swEgressACLIpRuleMaskDstIpaddress object. The value of this object when not in use is … |
| 1.3.6.1.4.1.171.12.89.3.2.1.10 | ColumnswEgressACLIpRuleDscp | read-create | current | Specifies the value of DSCP. The value can be configured from 0 to 63. A value of -1 indicates that this object is not active. |
| 1.3.6.1.4.1.171.12.89.3.2.1.11 | ColumnswEgressACLIpRuleProtocol | read-create | current | Specifies the IP protocol. |
| 1.3.6.1.4.1.171.12.89.3.2.1.12 | ColumnswEgressACLIpRuleType | read-create | current | Specifies that the rule applies to the value of ICMP/IGMP type traffic. A value of -1 denotes that this object is not active. |
| 1.3.6.1.4.1.171.12.89.3.2.1.13 | ColumnswEgressACLIpRuleCode | read-create | current | Specifies that the rule applies to the value of ICMP code traffic. A value of -1 denotes that this object is not active. |
| 1.3.6.1.4.1.171.12.89.3.2.1.14 | ColumnswEgressACLIpRuleSrcPort | read-create | current | Specifies that the rule applies to the range of the TCP/UDP source ports. A value of -1 indicates that this object is not active. |
| 1.3.6.1.4.1.171.12.89.3.2.1.15 | ColumnswEgressACLIpRuleMaskSrcPort | read-create | current | Specifies the per rule mask for the L4 source port as defined in swEgressACLIpRuleSrcPort object. The value of this object when not in use is the corresponding… |
| 1.3.6.1.4.1.171.12.89.3.2.1.16 | ColumnswEgressACLIpRuleDstPort | read-create | current | Specifies the TCP/UDP destination port range. A value of -1 indicates that this object is not active. |
| 1.3.6.1.4.1.171.12.89.3.2.1.17 | ColumnswEgressACLIpRuleMaskDstPort | read-create | current | Specifies the per rule mask for the L4 destination port as defined in swEgressACLIpRuleDstPort object. The value of this object when not in use is the correspo… |
| 1.3.6.1.4.1.171.12.89.3.2.1.18 | ColumnswEgressACLIpRuleFlagBits | read-create | current | A value which indicates the set of TCP flags that this entity may potentially offer. The value is a sum of flag bits. This sum initially takes the value zero. … |
| 1.3.6.1.4.1.171.12.89.3.2.1.19 | ColumnswEgressACLIpRuleProtoID | read-create | current | Specifies that the rule applies to the value of IP protocol ID traffic. A value of -1 indicates that this object is not active. |
| 1.3.6.1.4.1.171.12.89.3.2.1.20 | ColumnswEgressACLIpRuleUserDefine | read-create | current | Specifies that the rule applies to the first four byte behind the IP header. |
| 1.3.6.1.4.1.171.12.89.3.2.1.21 | ColumnswEgressACLIpRuleUserDefineMask | read-create | current | Specifies the per rule mask for the first four byte behind the IP header as defined in swEgressACLIpRuleUserDefine object. |
| 1.3.6.1.4.1.171.12.89.3.2.1.22 | ColumnswEgressACLIpRuleVID | read-create | current | Specifies the VLAN-based rule. There are two conditions: 1. this rule will apply to all the ports; 2. packets must belong to this VLAN. This object and swEgres… |
| 1.3.6.1.4.1.171.12.89.3.2.1.23 | ColumnswEgressACLIpRulePort | read-create | current | Specifies that the access rule will only apply to the port. This object and swEgressACLIpRuleVID,swEgressACLIpRulePortGroup can not be set together.When you se… |
| 1.3.6.1.4.1.171.12.89.3.2.1.24 | ColumnswEgressACLIpRulePortGroup | read-create | current | Specifies that the access rule will only apply to port(s)which belong to this port group. This object and swEgressACLIpRuleVID,swEgressACLIpRulePort can not be… |
| 1.3.6.1.4.1.171.12.89.3.2.1.25 | ColumnswEgressACLIpRulePermit | read-create | current | This object indicates if the result of the packet examination is 'permit' or 'deny'. The default is 'permit'. deny - Specifies that packets matching the access… |
| 1.3.6.1.4.1.171.12.89.3.2.1.26 | ColumnswEgressACLIpRuleEnableReplacePriority | read-create | current | Specifies whether the packets that match the access profile will change the 802.1p priority tag field by the switch or not. |
| 1.3.6.1.4.1.171.12.89.3.2.1.27 | ColumnswEgressACLIpRuleReplacePriority | read-create | current | Specifies the priority will change in packets while the swEgressACLIpRuleEnablePriority is enabled.A value of -1 indicates that this object is not active. |
| 1.3.6.1.4.1.171.12.89.3.2.1.28 | ColumnswEgressACLIpRuleEnableReplaceDscp | read-create | current | Specifies if the switch will change priorities of packets that match the access profile DSCP field or not. |
| 1.3.6.1.4.1.171.12.89.3.2.1.29 | ColumnswEgressACLIpRuleReplaceDscp | read-create | current | Specifies a value to be written to the DSCP field of an outgoing packet that meets the criteria specified in the first part of the command. This value will ove… |
| 1.3.6.1.4.1.171.12.89.3.2.1.30 | ColumnswEgressAclIpRuleTimeRangeName | read-create | current | Specifies a name of a time-range associated with a specific egress ACL entry. The time-range name must first be created before being associated with the access… |
| 1.3.6.1.4.1.171.12.89.3.3 | TableswEgressACLIpv6RuleTable | not-accessible | current | This table contains the IPv6 egress ACL rule information. |
| 1.3.6.1.4.1.171.12.89.3.3.1 | RowswEgressACLIpv6RuleEntry | not-accessible | current | A list of information about egress ACL rules regarding the IPv6 part of each packet. |
| 1.3.6.1.4.1.171.12.89.3.3.1.1 | ColumnswEgressACLIpv6RuleProfileID | not-accessible | current | The ID of the egress ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.89.3.3.1.2 | ColumnswEgressACLIpv6RuleAccessID | not-accessible | current | The ID of the the egress ACL rule entry relates to the swEgressACLEtherRuleProfileID. When row creation is set to 0, this indicates the access ID will be assig… |
| 1.3.6.1.4.1.171.12.89.3.3.1.3 | ColumnswEgressACLIpv6RuleRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.89.3.3.1.4 | ColumnswEgressACLIpv6RuleClass | read-create | current | Specifies that the rule applies to the IPv6 class field. A value of -1 indicates that this object is not active. |
| 1.3.6.1.4.1.171.12.89.3.3.1.5 | ColumnswEgressACLIpv6RuleSrcIpv6Addr | read-create | current | Specifies that the rule applies to the source IPv6 address. |
| 1.3.6.1.4.1.171.12.89.3.3.1.6 | ColumnswEgressACLIpv6RuleMaskSrcIpv6Addr | read-create | current | Specifies that the per rule mask of swEgressACLIpv6RuleSrcIpv6Addr. The value of this object when not in use is the corresponding mask in the profile mask. Onc… |
| 1.3.6.1.4.1.171.12.89.3.3.1.7 | ColumnswEgressACLIpv6RuleDstIpv6Addr | read-create | current | Specifies that the rule applies to the destination IPv6 address. |
| 1.3.6.1.4.1.171.12.89.3.3.1.8 | ColumnswEgressACLIpv6RuleMaskDstIpv6Addr | read-create | current | Specifies that the rule applies to the destination IPv6 address. |
| 1.3.6.1.4.1.171.12.89.3.3.1.9 | ColumnswEgressACLIpv6RuleProtocol | read-create | current | Specifies the IPv6 protocol. |
| 1.3.6.1.4.1.171.12.89.3.3.1.10 | ColumnswEgressACLIpv6RuleType | read-create | current | Specifies that the rule applies to the value of ICMP type traffic. A value of -1 denotes that this object is not active. |
| 1.3.6.1.4.1.171.12.89.3.3.1.11 | ColumnswEgressACLIpv6RuleCode | read-create | current | Specifies that the rule applies to the value of ICMP code traffic. A value of -1 denotes that this object is not active. |
| 1.3.6.1.4.1.171.12.89.3.3.1.12 | ColumnswEgressACLIpv6RuleSrcPort | read-create | current | Specifies that the rule applies to the range of the TCP/UDP source ports. A value of -1 indicates that this object is not active. |
| 1.3.6.1.4.1.171.12.89.3.3.1.13 | ColumnswEgressACLIpv6RuleMaskSrcPort | read-create | current | Specifies that the per rule mask of swEgressACLIpv6RuleSrcPort. The value of this object when not in use is the corresponding mask in the profile mask. Once th… |
| 1.3.6.1.4.1.171.12.89.3.3.1.14 | ColumnswEgressACLIpv6RuleDstPort | read-create | current | Specifies the TCP/UDP destination port range. A value of -1 indicates that this object is not active. |
| 1.3.6.1.4.1.171.12.89.3.3.1.15 | ColumnswEgressACLIpv6RuleMaskDstPort | read-create | current | Specifies the per rule mask of swEgressACLIpv6RuleDstPort. The value of this object when not in use is the corresponding mask in the profile mask. Once the val… |
| 1.3.6.1.4.1.171.12.89.3.3.1.16 | ColumnswEgressACLIpv6RuleVID | read-create | current | Specifies this rule only applies to the specified VLAN. There are two conditions: 1.only the portlist that belongs to this VLAN will be included; 2.packets mus… |
| 1.3.6.1.4.1.171.12.89.3.3.1.17 | ColumnswEgressACLIpv6RulePort | read-create | current | Specifies that the access rule will only apply to the port. This object and swEgressACLIpv6RuleVID,swEgressACLIpv6RulePortGroup can not be set together.When yo… |
| 1.3.6.1.4.1.171.12.89.3.3.1.18 | ColumnswEgressACLIpv6RulePortGroup | read-create | current | Specifies that the access rule will apply only to port(s)which belong to this port group. This object and swEgressACLIpv6RuleVID,swEgressACLIpv6RulePort can no… |
| 1.3.6.1.4.1.171.12.89.3.3.1.19 | ColumnswEgressACLIpv6RulePermit | read-create | current | This object indicates if the result of the packet examination is 'permit' or 'deny'. The default is 'permit'. deny - Specifies that packets matching the access… |
| 1.3.6.1.4.1.171.12.89.3.3.1.20 | ColumnswEgressACLIpv6RuleEnableReplacePriority | read-create | current | Specifies if the switch will change priorities of packets that match the access profile 802.1p priority tag or not. |
| 1.3.6.1.4.1.171.12.89.3.3.1.21 | ColumnswEgressACLIpv6RuleReplacePriority | read-create | current | Specifies the priority will change in packets while the swEgressACLIpv6RuleReplacePriority is enabled.A value of -1 indicates that this object is not active. |
| 1.3.6.1.4.1.171.12.89.3.3.1.22 | ColumnswEgressACLIpv6RuleEnableReplaceDscp | read-create | current | Specifies if the switch will change priorities of packets that match the access profile DSCP field or not. |
| 1.3.6.1.4.1.171.12.89.3.3.1.23 | ColumnswEgressACLIpv6RuleReplaceDscp | read-create | current | Specifies a value to be written to the DSCP field of an outgoing packet that meets the criteria specified in the first part of the command. This value will ove… |
| 1.3.6.1.4.1.171.12.89.3.3.1.24 | ColumnswEgressAclIpv6RuleTimeRangeName | read-create | current | Specifies a name of a time-range associated with a specific egress ACL entry. The time-range name must first be created before being associated with the access… |
| 1.3.6.1.4.1.171.12.89.3.4 | TableswEgressACLCounterTable | not-accessible | current | This table maintains counter information associated with a specific rule in the egress ACL rule table. Please refer to the swEgressACLEtherRuleTable, swEgressA… |
| 1.3.6.1.4.1.171.12.89.3.4.1 | RowswEgressACLCounterEntry | not-accessible | current | The entry maintains counter information associated with the egress ACL rule table. |
| 1.3.6.1.4.1.171.12.89.3.4.1.1 | ColumnswEgressACLCounterProfileID | not-accessible | current | The ID of the egress ACL mask entry, which is unique in the mask list. |
| 1.3.6.1.4.1.171.12.89.3.4.1.2 | ColumnswEgressACLCounterAccessID | not-accessible | current | The ID of the egress ACL rule entry as related to the swEgressACLCounterProfileID. |
| 1.3.6.1.4.1.171.12.89.3.4.1.3 | ColumnswEgressACLCounterState | read-write | current | Specifies whether the counter feature will be enabled or disabled. 1. This is optional. The default is 'disabled'. 2. If the rule is not bound with flow-meter,… |
| 1.3.6.1.4.1.171.12.89.3.4.1.4 | ColumnswEgressACLCounterTotalCounter | read-only | current | The number of matched packets. |
| 1.3.6.1.4.1.171.12.89.3.4.1.5 | ColumnswEgressACLCounterGreenCounter | read-only | current | The number of matched green packets. |
| 1.3.6.1.4.1.171.12.89.3.4.1.6 | ColumnswEgressACLCounterYellowCounter | read-only | current | The number of matched yellow packets. |
| 1.3.6.1.4.1.171.12.89.3.4.1.7 | ColumnswEgressACLCounterRedCounter | read-only | current | The number of matched red packets. |
| 1.3.6.1.4.1.171.12.89.4 | NodeswEgressAclMeteringMgmt | |||
| 1.3.6.1.4.1.171.12.89.4.1 | TableswEgressAclMeterTable | not-accessible | current | This table is used to configure the flow-based metering function. The access rule must first be created before the parameters of this function can be applied. … |
| 1.3.6.1.4.1.171.12.89.4.1.1 | RowswEgressAclMeterEntry | not-accessible | current | This entry displays parameters and configurations set for the flow metering function. |
| 1.3.6.1.4.1.171.12.89.4.1.1.1 | ColumnswEgressAclMeterProfileID | not-accessible | current | The ID of the ACL mask entry is unique in the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.89.4.1.1.2 | ColumnswEgressAclMeterAccessID | not-accessible | current | The ID of the egress ACL rule entry as related to the swEgressAclMeterProfileID. |
| 1.3.6.1.4.1.171.12.89.4.1.1.3 | ColumnswEgressAclMeterRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.89.4.1.1.4 | ColumnswEgressAclMeterMode | read-create | current | tr-tcm: two rate three color mode; sr-tcm: single rate three color mode; |
| 1.3.6.1.4.1.171.12.89.4.1.1.5 | ColumnswEgressAclMeterTrtcmCir | read-create | current | Specifies the 'committed information rate' of 'two rate three color mode'. The unit is Kbps.A value of -1 indicates that this object is not active. |
| 1.3.6.1.4.1.171.12.89.4.1.1.6 | ColumnswEgressAclMeterTrtcmCbs | read-create | current | Specifies the 'committed burst size' of 'two rate three color mode'. 1. The unit is Kbytes. That is to say, 1 means 1Kbytes. 2. This parameter is an optional p… |
| 1.3.6.1.4.1.171.12.89.4.1.1.7 | ColumnswEgressAclMeterTrtcmPir | read-create | current | Specifies the 'Peak Information Rate' of 'two rate three color mode'. The unit is Kbps.A value of -1 indicates that this object is not active. |
| 1.3.6.1.4.1.171.12.89.4.1.1.8 | ColumnswEgressAclMeterTrtcmPbs | read-create | current | Specifies the 'peak burst size' of 'two rate three color mode'. 1. The unit is Kbytes. That is to say, 1 means 1kbytes. 2. This parameter is an optional parame… |
| 1.3.6.1.4.1.171.12.89.4.1.1.9 | ColumnswEgressAclMeterTrtcmColorMode | read-create | current | Specifies the meter mode. The default is color-blind mode. The final color of the packet is determined by the initial color of the packet and the metering resu… |
| 1.3.6.1.4.1.171.12.89.4.1.1.10 | ColumnswEgressAclMeterTrtcmConformState | read-create | current | Specifies the action state when packet is in 'green color'. permit: permit the packet. replace-dscp: change the DSCP value of packet. |
| 1.3.6.1.4.1.171.12.89.4.1.1.11 | ColumnswEgressAclMeterTrtcmConformReplaceDscp | read-create | current | Specifies the DSCP value of the packet when the packet is in 'green color'. A value of -1 indicates that this object is not active. |
| 1.3.6.1.4.1.171.12.89.4.1.1.12 | ColumnswEgressAclMeterTrtcmConformCounterState | read-create | current | Specifies the counter state when the packet is in 'green color'. 1. This is optional. The default is 'disabled'. 2. The resource may be limited so that the cou… |
| 1.3.6.1.4.1.171.12.89.4.1.1.13 | ColumnswEgressAclMeterTrtcmExceedState | read-create | current | Specifies the action state when packet is in 'yellow color'. permit: permit the packet. replace-dscp: change the DSCP value of the packet. drop: drop the packe… |
| 1.3.6.1.4.1.171.12.89.4.1.1.14 | ColumnswEgressAclMeterTrtcmExceedReplaceDscp | read-create | current | Specifies the DSCP value of packet when packet is in 'yellow color'. A value of -1 indicates that this object is not active. |
| 1.3.6.1.4.1.171.12.89.4.1.1.15 | ColumnswEgressAclMeterTrtcmExceedCounterState | read-create | current | Specifies the counter state when packet is in 'yellow color'. 1. This is optional. The default is 'disabled'. 2. The resource may be limited so that the counte… |
| 1.3.6.1.4.1.171.12.89.4.1.1.16 | ColumnswEgressAclMeterTrtcmViolateState | read-create | current | Specifies the action state when packet is in 'red color'. permit: permit the packet. replace-dscp: change the DSCP value of packet. drop: drop the packet. |
| 1.3.6.1.4.1.171.12.89.4.1.1.17 | ColumnswEgressAclMeterTrtcmViolateReplaceDscp | read-create | current | Specifies the DSCP value of the packet when packet is in 'red color'. A value of -1 indicates that this object is not active. |
| 1.3.6.1.4.1.171.12.89.4.1.1.18 | ColumnswEgressAclMeterTrtcmViolateCounterState | read-create | current | Specifies the counter state when packet is in 'red color'. 1. This is optional. The default is 'disabled'. 2. The resource may be limited so that the counter c… |
| 1.3.6.1.4.1.171.12.89.4.1.1.19 | ColumnswEgressAclMeterSrtcmCir | read-create | current | Specifies the 'committed information rate' of 'single rate three color mode'. The unit is Kbps. A value of -1 indicates that this object is not active |
| 1.3.6.1.4.1.171.12.89.4.1.1.20 | ColumnswEgressAclMeterSrtcmCbs | read-create | current | Specifies the 'committed burst size' of 'single rate three color mode'. The unit is Kbytes. That is to say, 1 means 1Kbytes. The set value range is 0..N.The va… |
| 1.3.6.1.4.1.171.12.89.4.1.1.21 | ColumnswEgressAclMeterSrtcmEbs | read-create | current | Specifies the 'Excess burst size' of 'single rate three color mode'. The unit is Kbytes. That is to say, 1 means 1kbytes. The set value range is 0..N.The value… |
| 1.3.6.1.4.1.171.12.89.4.1.1.22 | ColumnswEgressAclMeterSrtcmColorMode | read-create | current | Specifies the meter mode. The default is color-blind mode. The final color of packet is determined by the initial color of the packet and the metering result. |
| 1.3.6.1.4.1.171.12.89.4.1.1.23 | ColumnswEgressAclMeterSrtcmConformState | read-create | current | Specifies the action state when the packet is in 'green color'. permit: permit the packet. replace-dscp: change the DSCP value of packet. |
| 1.3.6.1.4.1.171.12.89.4.1.1.24 | ColumnswEgressAclMeterSrtcmConformReplaceDscp | read-create | current | Specifies the DSCP value of the packet when packet is in 'green color'. A value of -1 indicates that this object is not active. |
| 1.3.6.1.4.1.171.12.89.4.1.1.25 | ColumnswEgressAclMeterSrtcmConformCounterState | read-create | current | Specifies the counter state when the packet is in 'green color'. 1. This is optional. The default is 'disabled'. 2. The resource may be limited such that count… |
| 1.3.6.1.4.1.171.12.89.4.1.1.26 | ColumnswEgressAclMeterSrtcmExceedState | read-create | current | Specifies the action state when the packet is in 'yellow color'. permit: permit the packet. replace-dscp: change the DSCP value of packet. drop: drop the packe… |
| 1.3.6.1.4.1.171.12.89.4.1.1.27 | ColumnswEgressAclMeterSrtcmExceedReplaceDscp | read-create | current | Specifies the DSCP value of the packet when packet is in 'yellow color'. A value of -1 indicates that this object is not active. |
| 1.3.6.1.4.1.171.12.89.4.1.1.28 | ColumnswEgressAclMeterSrtcmExceedCounterState | read-create | current | Specifies the counter state when the packet is in 'yellow color'. 1. This is optional. The default is 'disabled'. 2. The resource may be limited such that coun… |
| 1.3.6.1.4.1.171.12.89.4.1.1.29 | ColumnswEgressAclMeterSrtcmViolateState | read-create | current | Specifies the action state when the packet is in 'red color'. permit: permit the packet. replace-dscp: change the DSCP value of packet. drop: drop the packet. |
| 1.3.6.1.4.1.171.12.89.4.1.1.30 | ColumnswEgressAclMeterSrtcmViolateReplaceDscp | read-create | current | Specifies the DSCP value of the packet when packet is in 'red color'. A value of -1 indicates that this object is not active. |
| 1.3.6.1.4.1.171.12.89.4.1.1.31 | ColumnswEgressAclMeterSrtcmViolateCounterState | read-create | current | Specifies the counter state when the packet is in 'red color'. 1. This is optional. The default is 'diabled'. 2. The resource may be limited so that the counte… |
| 1.3.6.1.4.1.171.12.89.4.2 | TableswEgressAclRateTable | not-accessible | current | This table is used to configure the single rate two color metering function. The egress access rule must first be created before the parameters of this functio… |
| 1.3.6.1.4.1.171.12.89.4.2.1 | RowswEgressAclRateEntry | not-accessible | current | This entry displays parameters and configurations set for the single rate two color function. |
| 1.3.6.1.4.1.171.12.89.4.2.1.1 | ColumnswEgressAclRateProfileID | not-accessible | current | The ID of the egress ACL mask entry is unique in the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.89.4.2.1.2 | ColumnswEgressAclRateAccessID | not-accessible | current | The ID of the egress ACL rule entry as related to the swEgressAclRateProfileID. |
| 1.3.6.1.4.1.171.12.89.4.2.1.3 | ColumnswEgressAclRateRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.89.4.2.1.4 | ColumnswEgressAclRate | read-create | current | Specifies the committed bandwidth in Kbps for the flow. A value of -1 indicates that this object is not active. NOTE: Users must set the swEgressAclRateActionF… |
| 1.3.6.1.4.1.171.12.89.4.2.1.5 | ColumnswEgressAclBurstSize | read-create | current | This specifies the burst size for the single rate two color mode. The unit is Kbytes. That is to say, 1 means 1kbytes. The set value range is 0..N, the value N… |
| 1.3.6.1.4.1.171.12.89.4.2.1.6 | ColumnswEgressAclRateActionForRateExceed | read-create | current | Specifies the action to take for those packets exceeding the committed rate. drop-packet: drop the packet. replace-dscp: change the DSCP value of the packet. N… |
| 1.3.6.1.4.1.171.12.89.4.2.1.7 | ColumnswEgressAclRateRemarkDscp | read-create | current | Mark the packet with a specified DSCP. It can be set when swEgressAclRateActionForRateExceed sets remark-dscp(3). A value of -1 indicates that this object is n… |
| 1.3.6.1.4.1.171.12.89.4.3 | ScalarswEgressAclMeteringNumOfEntryInUse | read-only | current | Used to display total entries of the flow metering. |