EKINOPS-PM1001LH-MIB
820 objects
MIB for managing Ekinops modules with PM1001LH software
Imported Objects
| EKINOPS-MIB | EkiApiState EkiMeasureType EkiMode ekinops EkiOnOff EkiProtocol EkiState EkiSynchroMode |
| SNMPv2-SMI | Counter32 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.20044.10 | Identitymodulepm1001lh | MIB for managing Ekinops modules with PM1001LH software | ||
| 1.3.6.1.4.1.20044.10.2 | Nodepm1001lhalarms | |||
| 1.3.6.1.4.1.20044.10.2.1 | Nodepm1001lhAlmOther | |||
| 1.3.6.1.4.1.20044.10.2.1.1 | Nodepm1001lhAlmOtherNurg | |||
| 1.3.6.1.4.1.20044.10.2.1.1.2 | Nodepm1001lhAlmsynthAlm2 | |||
| 1.3.6.1.4.1.20044.10.2.1.1.2.1 | Scalarpm1001lhAlmConfTableSave | read-only | current | PM Configuration Save :This OID is at 1 during the saving of a new configuration table in the module Flash memory. <Condtype> CONF_TABLE_SAVE <Probcause> other… |
| 1.3.6.1.4.1.20044.10.2.1.1.2.2 | Scalarpm1001lhAlmInvUpload | read-only | current | Inventory Upload :This OID is at 1 during the uploading of PM inventory information. <Condtype> INV_UPLOAD <Probcause> other (1) <Alarmtype> other (1) <Polarit… |
| 1.3.6.1.4.1.20044.10.2.1.1.2.3 | Scalarpm1001lhAlmConfTableLoad | read-only | current | PM Configuration Load :This OID is at 1 during the loading of configuration tables in the modules RAM. <Condtype> CONF_TABLE_LOAD <Probcause> other (1) <Alarmt… |
| 1.3.6.1.4.1.20044.10.2.1.1.2.4 | Scalarpm1001lhAlmCorrelatOff | read-only | current | Not Used :This OID, when set, indicates that alarm correlation is not being performed. <Condtype> CORRELAT_OFF <Probcause> other (1) <Alarmtype> other (1) <Pol… |
| 1.3.6.1.4.1.20044.10.2.1.1.2.5 | Scalarpm1001lhAlmMaintenanceOn | read-only | current | Maintenance Mode :This OID indicates that the PM is in maintenance mode. <Help> This alarm indicates that the maintenance mode is enabled on the PM <Condtype> … |
| 1.3.6.1.4.1.20044.10.2.1.2 | Nodepm1001lhAlmOtherUrg | |||
| 1.3.6.1.4.1.20044.10.2.1.2.194 | Nodepm1001lhAlmmodInitFailLevel2 | |||
| 1.3.6.1.4.1.20044.10.2.1.2.194.1 | Scalarpm1001lhAlmLedFail | read-only | current | Led Fail :This OID indicates that Led register has not been correctly initalized <Help> This alarm indicates if the module LEDs are correctly initialized <Cond… |
| 1.3.6.1.4.1.20044.10.2.1.2.194.2 | Scalarpm1001lhAlmNextColdBootForced | read-only | current | Next Cold Boot Forced :This OID indicates that the next Reset will be forced Cold <Help> This alarm indicates that the next reset of the module will be forced … |
| 1.3.6.1.4.1.20044.10.2.1.2.194.3 | Scalarpm1001lhAlmBootUndone | read-only | current | Boot Undone :This OID indicates that the boot has not been correctly achieved <Help> This alarm indicates if the module has correctly boot <Condtype> BOOT_UNDO… |
| 1.3.6.1.4.1.20044.10.2.1.2.194.4 | Scalarpm1001lhAlmResetHwInitFail | read-only | current | Reset HW Init Fail :This OID indicates that the HW intialization has caused unknown intial conditions <Help> This alarm indicates if the HW has been correctly … |
| 1.3.6.1.4.1.20044.10.2.1.2.194.5 | Scalarpm1001lhAlmSwInitFail | read-only | current | SW Init Fail :This OID indicates that the SW intialization has caused unknown intial conditions <Help> This alarm indicates if the SW module is correctly initi… |
| 1.3.6.1.4.1.20044.10.2.1.2.195 | Nodepm1001lhAlmmodInitFailLevel3 | |||
| 1.3.6.1.4.1.20044.10.2.1.2.195.1 | Scalarpm1001lhAlmGwIdentFail | read-only | current | GW Ident Fail :This OID indicates that GW identification has not been read <Help> This alarm indicates if the GW has been correctly identified <Condtype> GW_ID… |
| 1.3.6.1.4.1.20044.10.2.1.2.195.2 | Scalarpm1001lhAlmObmTypeReadFail | read-only | current | OBM Type Read Fail :This OID indicates that OBM type has not been recognized <Help> This alarm indicates if the OBM board has been correctly identified <Condty… |
| 1.3.6.1.4.1.20044.10.2.1.2.195.3 | Scalarpm1001lhAlmInitModuleFail | read-only | current | Init Module Fail :This OID indicates that the Module has not been correctly initialized <Help> This alarm indicates if the SW module is correctly initialized <… |
| 1.3.6.1.4.1.20044.10.2.1.2.195.5 | Scalarpm1001lhAlmXfp1InitFail | read-only | current | XFP1 Init Fail :This OID indicates that the XFP has not been correctly initialized <Help> This alarm indicates if the line transceiver 1 is correctly initializ… |
| 1.3.6.1.4.1.20044.10.2.1.2.195.6 | Scalarpm1001lhAlmXfp2InitFail | read-only | current | XFP2 Init Fail :This OID indicates that the XFP has not been correctly initialized <Help> This alarm indicates if the line transceiver 2 is correctly initializ… |
| 1.3.6.1.4.1.20044.10.2.1.2.195.7 | Scalarpm1001lhAlmLine1InitFail | read-only | current | Line1 Init Fail :This OID indicates that the Line registersvsubset has not been correctly initialized <Help> This alarm indicates if the line port is correctly… |
| 1.3.6.1.4.1.20044.10.2.1.2.195.9 | Scalarpm1001lhAlmClient1InitFail | read-only | current | Client1 Init Fail :This OID indicates that Client 1 registers subset has not been correctly initialized <Help> This alarm indicates if the client port is corre… |
| 1.3.6.1.4.1.20044.10.2.1.3 | Nodepm1001lhAlmOtherCrit | |||
| 1.3.6.1.4.1.20044.10.2.1.3.0 | Nodepm1001lhAlmsynthAlm0 | |||
| 1.3.6.1.4.1.20044.10.2.1.3.0.9 | Scalarpm1001lhAlmModGlobFail | read-only | current | Module Failure :This OID is set on detection of a failure originating from the PM <Condtype> MOD_GLOB_FAIL <Probcause> equipmentMalfunction (16) <Alarmtype> sy… |
| 1.3.6.1.4.1.20044.10.2.1.3.0.15 | Scalarpm1001lhAlmDefFuseA | read-only | current | Fuse A Fail :This OID indicates that the fuse of the power input A is in fail condition <Help> Status of the Fuse A <Condtype> DEF_FUSE_A <Probcause> powerProb… |
| 1.3.6.1.4.1.20044.10.2.1.3.0.16 | Scalarpm1001lhAlmDefFuseB | read-only | current | Fuse B Fail :This OID indicates that the fuse of the power input B is in fail condition <Help> Status of the Fuse B <Condtype> DEF_FUSE_B <Probcause> powerProb… |
| 1.3.6.1.4.1.20044.10.2.2 | Nodepm1001lhAlmClient | |||
| 1.3.6.1.4.1.20044.10.2.2.1 | Nodepm1001lhAlmClientNurg | |||
| 1.3.6.1.4.1.20044.10.2.2.1.48 | Nodepm1001lhAlmclientXfpWarnings | |||
| 1.3.6.1.4.1.20044.10.2.2.1.48.1 | Scalarpm1001lhAlmClientTxPowerLowWarning | read-only | current | Client Optical Tx Pwr Low Warning :Warning indicating that the XFP/OTX transmitter transmitter output power is lower than the threshold value written in the XF… |
| 1.3.6.1.4.1.20044.10.2.2.1.48.2 | Scalarpm1001lhAlmClientTxPowerHighWarning | read-only | current | Client Optical Tx Pwr High Warning :Warning indicating that the XFP/OTX transmitter transmitter output power is higher than the threshold value written in the … |
| 1.3.6.1.4.1.20044.10.2.2.1.48.3 | Scalarpm1001lhAlmClientTxBiasLowWarning | read-only | current | Client Transceiver Bias Low Warning :Warning indicating that the XFP/OTX transmitter laser bias current is lower than the threshold value written in the XFP/OT… |
| 1.3.6.1.4.1.20044.10.2.2.1.48.4 | Scalarpm1001lhAlmClientTxBiasHighWarning | read-only | current | Client Transceiver Bias High Warning :Warning indicating that the XFP/OTX transmitter laser bias current is higher than the threshold value written in the XFP … |
| 1.3.6.1.4.1.20044.10.2.2.1.48.7 | Scalarpm1001lhAlmClientTempLowWarning | read-only | current | Client Transceiver Temp Low Warning :Warning indicating that the XFP/OTX temperature is lower than the threshold value written in the XFP/OTX EEPROM <Condtype>… |
| 1.3.6.1.4.1.20044.10.2.2.1.48.8 | Scalarpm1001lhAlmClientTempHighWarning | read-only | current | Client Transceiver Temp High Warning :Warning indicating that the XFP/OTX temperature is higher than the threshold value written in the XFP EEPROM <Condtype> C… |
| 1.3.6.1.4.1.20044.10.2.2.1.48.15 | Scalarpm1001lhAlmClientRxPowerLowWarning | read-only | current | Client Optical Rx Pwr Low Warning :Warning indicating that the XFP received optical power is lower than the threshold value written in the XFP EEPROM <Condtype… |
| 1.3.6.1.4.1.20044.10.2.2.1.48.16 | Scalarpm1001lhAlmClientRxPowerHighWarning | read-only | current | Client Optical Rx Pwr High Warning :Warning indicating that the XFP received optical power is higher than the threshold value written in the XFP EEPROM <Condty… |
| 1.3.6.1.4.1.20044.10.2.2.2 | Nodepm1001lhAlmClientUrg | |||
| 1.3.6.1.4.1.20044.10.2.2.2.32 | Nodepm1001lhAlmclientXfpAlarm1 | |||
| 1.3.6.1.4.1.20044.10.2.2.2.32.1 | Scalarpm1001lhAlmClientTxPowerLowAlarm | read-only | current | Client Optical Tx Power Low :Alarm indicating that the XFP/OTX transmitter transmitter output power is lower than the threshold value written in the XFP/OTX EE… |
| 1.3.6.1.4.1.20044.10.2.2.2.32.2 | Scalarpm1001lhAlmClientTxPowerHighAlarm | read-only | current | Client Optical Tx Power High :Alarm indicating that the XFP/OTX transmitter transmitter output power is higher than the threshold value written in the XFP EEPR… |
| 1.3.6.1.4.1.20044.10.2.2.2.32.3 | Scalarpm1001lhAlmClientTxBiasLowAlarm | read-only | current | Client Transceiver Bias Low :Alarm indicating that the XFP/OTX transmitter laser bias current is lower than the threshold value written in the XFP/OTX EEPROM <… |
| 1.3.6.1.4.1.20044.10.2.2.2.32.4 | Scalarpm1001lhAlmClientTxBiasHighAlarm | read-only | current | Client Transceiver Bias High :Alarm indicating that the XFP/OTX transmitter laser bias current is higher than the threshold value written in the XFP EEPROM <Co… |
| 1.3.6.1.4.1.20044.10.2.2.2.32.7 | Scalarpm1001lhAlmClientTempLowAlarm | read-only | current | Client Transceiver Temp Low :Alarm indicating that the XFP/OTX temperature is lower than the threshold value written in the XFP/OTX EEPROM <Condtype> CLIENT_TE… |
| 1.3.6.1.4.1.20044.10.2.2.2.32.8 | Scalarpm1001lhAlmClientTempHighAlarm | read-only | current | Client Transceiver Temp High :Alarm indicating that the XFP/OTX temperature is higher than the threshold value written in the XFP EEPROM <Condtype> CLIENT_TEMP… |
| 1.3.6.1.4.1.20044.10.2.2.2.32.15 | Scalarpm1001lhAlmClientRxPowerLowAlarm | read-only | current | Client Optical Rx Power Low :Alarm indicating that the XFP received optical power is lower than the threshold value written in the XFP EEPROM <Condtype> CLIENT… |
| 1.3.6.1.4.1.20044.10.2.2.2.32.16 | Scalarpm1001lhAlmClientRxPowerHighAlarm | read-only | current | Client Optical Rx Power High :Alarm indicating that the XFP received optical power is higher than the threshold value written in the XFP EEPROM <Condtype> CLIE… |
| 1.3.6.1.4.1.20044.10.2.2.2.64 | Nodepm1001lhAlmclientXfpSupplyAlarm | |||
| 1.3.6.1.4.1.20044.10.2.2.2.64.1 | Scalarpm1001lhAlmClientVee5LowAlarm | read-only | current | VEE5 Power Supply Low :Alarm indicating the XFP/OTX VEE5 power supply is lower than the threshold written in the EEPROM <Condtype> CLIENT_VEE5_LOW_ALARM <Probc… |
| 1.3.6.1.4.1.20044.10.2.2.2.64.2 | Scalarpm1001lhAlmClientVee5HighAlarm | read-only | current | VEE5 Power Supply High :Alarm indicating the XFP/OTX VEE5 power supply is higher than the threshold written in the EEPROM <Condtype> CLIENT_VEE5_HIGH_ALARM <Pr… |
| 1.3.6.1.4.1.20044.10.2.2.2.64.3 | Scalarpm1001lhAlmClientVcc2LowAlarm | read-only | current | VCC2 Power Supply Low :Alarm indicating the XFP/OTX VCC2 power supply is lower than the threshold written in the EEPROM <Condtype> CLIENT_VCC2_LOW_ALARM <Probc… |
| 1.3.6.1.4.1.20044.10.2.2.2.64.4 | Scalarpm1001lhAlmClientVcc2HighAlarm | read-only | current | VCC2 Power Supply High :Alarm indicating the XFP/OTX VCC2 power supply is higher than the threshold written in the EEPROM <Condtype> CLIENT_VCC2_HIGH_ALARM <Pr… |
| 1.3.6.1.4.1.20044.10.2.2.2.64.5 | Scalarpm1001lhAlmClientVcc3LowAlarm | read-only | current | VCC3 Power Supply Low :Alarm indicating the XFP/OTX VCC3 power supply is lower than the threshold written in the EEPROM <Condtype> CLIENT_VCC3_LOW_ALARM <Probc… |
| 1.3.6.1.4.1.20044.10.2.2.2.64.6 | Scalarpm1001lhAlmClientVcc3HighAlarm | read-only | current | VCC3 Power Supply High :Alarm indicating the XFP/OTX VCC3 power supply is higher than the threshold written in the EEPROM <Condtype> CLIENT_VCC3_HIGH_ALARM <Pr… |
| 1.3.6.1.4.1.20044.10.2.2.2.64.7 | Scalarpm1001lhAlmClientVcc5LowAlarm | read-only | current | VCC5 Power Supply Low :Alarm indicating the XFP/OTX VCC5 power supply is lower than the threshold written in the EEPROM <Condtype> CLIENT_VCC5_LOW_ALARM <Probc… |
| 1.3.6.1.4.1.20044.10.2.2.2.64.8 | Scalarpm1001lhAlmClientVcc5HighAlarm | read-only | current | VCC5 Power Supply High :Alarm indicating the XFP/OTX VCC5 power supply is higher than the threshold written in the EEPROM <Condtype> CLIENT_VCC5_HIGH_ALARM <Pr… |
| 1.3.6.1.4.1.20044.10.2.2.2.64.9 | Scalarpm1001lhAlmClientVee5LowWarning | read-only | current | VEE5 Power Supply Low Warning :Warning indicating the XFP/OTX VEE5 power supply is lower than the threshold written in the EEPROM <Condtype> CLIENT_VEE5_LOW_WA… |
| 1.3.6.1.4.1.20044.10.2.2.2.64.10 | Scalarpm1001lhAlmClientVee5HighWarning | read-only | current | VEE5 Power Supply High Warning :Warning indicating the XFP/OTX VEE5 power supply is higher than the threshold written in the EEPROM <Condtype> CLIENT_VEE5_HIGH… |
| 1.3.6.1.4.1.20044.10.2.2.2.64.11 | Scalarpm1001lhAlmClientVcc2LowWarning | read-only | current | VCC2 Power Supply Low Warning :Warning indicating the XFP/OTX VCC2 power supply is lower than the threshold written in the EEPROM <Condtype> CLIENT_VCC2_LOW_WA… |
| 1.3.6.1.4.1.20044.10.2.2.2.64.12 | Scalarpm1001lhAlmClientVcc2HighWarning | read-only | current | VCC2 Power Supply High Warning :Warning indicating the XFP/OTX VCC2 power supply is higher than the threshold written in the EEPROM <Condtype> CLIENT_VCC2_HIGH… |
| 1.3.6.1.4.1.20044.10.2.2.2.64.13 | Scalarpm1001lhAlmClientVcc3LowWarning | read-only | current | VCC3 Power Supply Low Warning :Warning indicating the XFP/OTX VCC3 power supply is lower than the threshold written in the EEPROM <Condtype> CLIENT_VCC3_LOW_WA… |
| 1.3.6.1.4.1.20044.10.2.2.2.64.14 | Scalarpm1001lhAlmClientVcc3HighWarning | read-only | current | VCC3 Power Supply High Warning :Warning indicating the XFP/OTX VCC3 power supply is higher than the threshold written in the EEPROM <Condtype> CLIENT_VCC3_HIGH… |
| 1.3.6.1.4.1.20044.10.2.2.2.64.15 | Scalarpm1001lhAlmClientVcc5LowWarning | read-only | current | VCC5 Power Supply Low Warning :Warning indicating the XFP/OTX VCC5 power supply is lower than the threshold written in the EEPROM <Condtype> CLIENT_VCC5_LOW_WA… |
| 1.3.6.1.4.1.20044.10.2.2.2.64.16 | Scalarpm1001lhAlmClientVcc5HighWarning | read-only | current | VCC5 Power Supply High Warning :Warning indicating the XFP/OTX VCC5 power supply is higher than the threshold written in the EEPROM <Condtype> CLIENT_VCC5_HIGH… |
| 1.3.6.1.4.1.20044.10.2.2.3 | Nodepm1001lhAlmClientCrit | |||
| 1.3.6.1.4.1.20044.10.2.2.3.8 | Nodepm1001lhAlmsynthAlmPort | |||
| 1.3.6.1.4.1.20044.10.2.2.3.8.1 | Scalarpm1001lhAlmClientXfpAbsent | read-only | current | Client Optical Module Absent :This OID indicates that the XFP module is not present in the client port. <Help> This alarm indicates if the client transceiver i… |
| 1.3.6.1.4.1.20044.10.2.2.3.8.2 | Scalarpm1001lhAlmClientDdmAbsent | read-only | current | Client Optical Module Ready :This OID indicates that the client optical interface (XFP or OTX) is not operational. <Help> This status indicates if the client t… |
| 1.3.6.1.4.1.20044.10.2.2.3.8.4 | Scalarpm1001lhAlmClientHwFail | read-only | current | Client HW Fail :This OID indicates a failure on client port, most probably caused by a HW issue. <Condtype> CLIENT_HW_FAIL <Probcause> equipmentMalfunction (16… |
| 1.3.6.1.4.1.20044.10.2.2.3.8.5 | Scalarpm1001lhAlmClientDwLsd | read-only | current | Client Optical Laser Shutdown :This OID indicates the Client XFP transmitter output is ON. <Help> This status indicates if the client transceiver laser is ON o… |
| 1.3.6.1.4.1.20044.10.2.2.3.8.6 | Scalarpm1001lhAlmClientLocalOos | read-only | current | Local Client Port In Service :This OID indicates that the local Client port is In Service (1) or Out of Service (2) <Help> This status indicates if the local c… |
| 1.3.6.1.4.1.20044.10.2.2.3.8.8 | Scalarpm1001lhAlmClientDwCais | read-only | current | Client AIS Inserted :This OID indicates a CAIS has been inserted on the output client port. <Help> This status indicates if a Client Alarm Indication Signal is… |
| 1.3.6.1.4.1.20044.10.2.2.3.8.9 | Scalarpm1001lhAlmClientXfpDdmWarning | read-only | current | Warning On Client XFP DDM :This OID indicates a warning is being received from the Client XFP DDM <Help> This alarm indicates if a DDM Warning has been detecte… |
| 1.3.6.1.4.1.20044.10.2.2.3.8.10 | Scalarpm1001lhAlmClientXfpDdmAlm | read-only | current | Alarm On Client XFP DDM :This OID indicates an alarm is being received from the Client XFP DDM <Help> This alarm indicates if a DDM Alarm has been detected on … |
| 1.3.6.1.4.1.20044.10.2.2.3.8.12 | Scalarpm1001lhAlmClientFail | read-only | current | Client Access Fail :This OID indicates a failure on the Client port <Condtype> CLIENT_FAIL <Probcause> equipmentMalfunction (16) <Alarmtype> synthesisAlarm (12… |
| 1.3.6.1.4.1.20044.10.2.2.3.8.16 | Scalarpm1001lhAlmClientUpCsf | read-only | current | Client Signal Fail Inserted :This OID indicates a CSF has been inserted in the upstream client port. <Help> This status indicates if a Client Signal Fail is cu… |
| 1.3.6.1.4.1.20044.10.2.2.3.16 | Nodepm1001lhAlmclientAccessioAlm | |||
| 1.3.6.1.4.1.20044.10.2.2.3.16.1 | Scalarpm1001lhAlmClientDwLasFail | read-only | current | Client XFP Tx Failed :This OID indicates that the transmitter fails for the XFP plugged into the client port (this alarm reports the transmitter failure alarm … |
| 1.3.6.1.4.1.20044.10.2.2.3.16.4 | Scalarpm1001lhAlmClientUpLos | read-only | current | Client Input Loss Of Signal :This OID indicates that no signal is present on the XFP of the client port <Help> This alarm indicates if an optical signal is det… |
| 1.3.6.1.4.1.20044.10.2.2.3.40 | Nodepm1001lhAlmclientXfpAlarm2 | |||
| 1.3.6.1.4.1.20044.10.2.2.3.40.2 | Scalarpm1001lhAlmClientModNr | read-only | current | Client Optical Module Not Ready :This OID indicates that the module is unable to determine correct data. <Help> This alarm indicates if the Client transceiver … |
| 1.3.6.1.4.1.20044.10.2.2.3.40.3 | Scalarpm1001lhAlmClientRxCdrNotLocked1 | read-only | current | Client Optical Rx CDR Unlocked :This OID indicates that a loss of lock on the receiving side CDR has been detected <Help> This alarm indicates if the Rx CDR is… |
| 1.3.6.1.4.1.20044.10.2.2.3.40.5 | Scalarpm1001lhAlmClientRxNr | read-only | current | Client Optical Rx Not Ready :This OID indicates that a condition has arisen leading to invalid data on the receiving side. <Help> This alarm indicates if the R… |
| 1.3.6.1.4.1.20044.10.2.2.3.40.6 | Scalarpm1001lhAlmClientTxCdrNotLocked1 | read-only | current | Client Optical Tx CDR Unlocked :This OID indicates a loss of lock on the transmitting side CDR has been detected. <Help> This alarm indicates if the Tx CDR is … |
| 1.3.6.1.4.1.20044.10.2.2.3.40.7 | Scalarpm1001lhAlmClientTxFault | read-only | current | Client Optical Tx Failure :This OID indicates a fault condition on the laser detected by the safety syste <Help> This alarm indicates if the laser of the Clien… |
| 1.3.6.1.4.1.20044.10.2.2.3.40.8 | Scalarpm1001lhAlmClientTxNr | read-only | current | Client Optical Tx Not Ready :This OID indicates a condition has arisen leading to invalid data on the transmitting side <Help> This alarm indicates if the Tx p… |
| 1.3.6.1.4.1.20044.10.2.2.3.40.14 | Scalarpm1001lhAlmClientWavelengthUnlocked | read-only | current | Client Optical Tx Wavelength Unlocked :This OID indicates that the wavelength error is exceeding the manufacturer tolerance <Help> This alarm indicates if the … |
| 1.3.6.1.4.1.20044.10.2.2.3.40.15 | Scalarpm1001lhAlmClientTecFault | read-only | current | Client Optical Tx Temp Regul. Failed :This OID indicates a failure on the TEC module <Help> This alarm indicates if the TEC of the Client transceiver is in fai… |
| 1.3.6.1.4.1.20044.10.2.2.3.40.16 | Scalarpm1001lhAlmClientApdSupplyFault | read-only | current | Client Rx Photodiode Power Failed :This OID indicates a failure on the APD power supply <Help> This alarm indicates if the APD power supply is in fail conditio… |
| 1.3.6.1.4.1.20044.10.2.2.3.72 | Nodepm1001lhAlmclientMapperDeAlm | |||
| 1.3.6.1.4.1.20044.10.2.2.3.72.1 | Scalarpm1001lhAlmClientUpAccOos | read-only | current | Client Loss Of Synchronisation :This OID indicates the upstream client input port is in Loss of Synchronization <Help> This alarms indicates if the input clien… |
| 1.3.6.1.4.1.20044.10.2.2.3.72.10 | Scalarpm1001lhAlmClientUpBufferOvl | read-only | current | Client Upstream Buffer Overload :This OID indicates that the rate adaptation buffer for client port is in overload. <Condtype> CLIENT_UP_BUFFER_OVL <Probcause>… |
| 1.3.6.1.4.1.20044.10.2.2.3.72.11 | Scalarpm1001lhAlmClientDwCsfDet | read-only | current | Client Signal Fail Detected :This OID indicates that a CSF has been detected on client port in the downstream direction <Help> This alarm indicates if a Client… |
| 1.3.6.1.4.1.20044.10.2.2.3.72.14 | Scalarpm1001lhAlmClientDwBufferOvl | read-only | current | Client Downstream Buffer Overload :This OID indicates that the de-mapper buffer for client port is in overload. <Condtype> CLIENT_DW_BUFFER_OVL <Probcause> equ… |
| 1.3.6.1.4.1.20044.10.2.3 | Nodepm1001lhAlmLine | |||
| 1.3.6.1.4.1.20044.10.2.3.1 | Nodepm1001lhAlmLineNurg | |||
| 1.3.6.1.4.1.20044.10.2.3.1.209 | Nodepm1001lhAlmlineXfpWarnings | |||
| 1.3.6.1.4.1.20044.10.2.3.1.209.1 | Scalarpm1001lhAlmLineTxPowerLowWarning | read-only | current | Line Optical Tx Power Low Warning :Warning indicating that the XFP/OTX transmitter transmitter output power is lower than the threshold value written in the XF… |
| 1.3.6.1.4.1.20044.10.2.3.1.209.2 | Scalarpm1001lhAlmLineTxPowerHighWarning | read-only | current | Line Optical Tx Power High Warning :Warning indicating that the XFP/OTX transmitter transmitter output power is higher than the threshold value written in the … |
| 1.3.6.1.4.1.20044.10.2.3.1.209.3 | Scalarpm1001lhAlmLineTxBiasLowWarning | read-only | current | Line Transceiver Bias Low Warning :Warning indicating that the XFP/OTX transmitter laser bias current is lower than the threshold value written in the XFP/OTX … |
| 1.3.6.1.4.1.20044.10.2.3.1.209.4 | Scalarpm1001lhAlmLineTxBiasHighWarning | read-only | current | Line Transceiver Bias High Warning :Warning indicating that the XFP/OTX transmitter laser bias current is higher than the threshold value written in the XFP EE… |
| 1.3.6.1.4.1.20044.10.2.3.1.209.7 | Scalarpm1001lhAlmLineTempLowWarning | read-only | current | Line Transceiver Temp Low Warning :Warning indicating that the XFP/OTX temperature is lower than the threshold value written in the XFP/OTX EEPROM <Condtype> L… |
| 1.3.6.1.4.1.20044.10.2.3.1.209.8 | Scalarpm1001lhAlmLineTempHighWarning | read-only | current | Line Transceiver Temp High Warning :Warning indicating that the XFP/OTX temperature is higher than the threshold value written in the XFP EEPROM <Condtype> LIN… |
| 1.3.6.1.4.1.20044.10.2.3.1.209.15 | Scalarpm1001lhAlmLineRxPowerLowWarning | read-only | current | Line Optical Rx Power Low Warning :Warning indicating that the XFP received optical power is lower than the threshold value written in the XFP EEPROM <Condtype… |
| 1.3.6.1.4.1.20044.10.2.3.1.209.16 | Scalarpm1001lhAlmLineRxPowerHighWarning | read-only | current | Line Optical Rx Power High Warning :Warning indicating that the XFP received optical power is higher than the threshold value written in the XFP EEPROM <Condty… |
| 1.3.6.1.4.1.20044.10.2.3.1.225 | Nodepm1001lhAlmlineOtxTlhWarnings | |||
| 1.3.6.1.4.1.20044.10.2.3.1.225.5 | Scalarpm1001lhAlmLineModulatorAgingHighWarning | read-only | current | Line Modulator Aging High Warning :Warning indicating the Line OTX TLH modulator aging is higher than the threshold written in the EEPROM <Condtype> LINE_MODUL… |
| 1.3.6.1.4.1.20044.10.2.3.1.225.6 | Scalarpm1001lhAlmLineAgingHighWarning | read-only | current | Line OTX TLH Aging High Warning :Warning indicating the Line OTX TLH aging is higher than the threshold written in the EEPROM <Condtype> LINE_AGING_HIGH_WARNIN… |
| 1.3.6.1.4.1.20044.10.2.3.1.225.12 | Scalarpm1001lhAlmLineFreqDevHighWarning | read-only | current | Line Freq. Deviation High Warning :Warning indicating the Line OTX TLH frequency deviation is higher than the threshold written in the EEPROM <Condtype> LINE_F… |
| 1.3.6.1.4.1.20044.10.2.3.1.225.14 | Scalarpm1001lhAlmLineLaserTempHighWarning | read-only | current | Line Laser Temp. High Warning :Warning indicating the Line OTX TLH laser temperature is higher than the threshold written in the EEPROM <Condtype> LINE_LASER_T… |
| 1.3.6.1.4.1.20044.10.2.3.2 | Nodepm1001lhAlmLineUrg | |||
| 1.3.6.1.4.1.20044.10.2.3.2.129 | Nodepm1001lhAlmdfrmBer | |||
| 1.3.6.1.4.1.20044.10.2.3.2.129.1 | Scalarpm1001lhAlmLineSignalDegrade | read-only | current | Custom Line Signal Degrade :This OID indicates that the line input signal is DEGRADE. The assertion hysteresis can customized by the host <Condtype> LINE_SIGNA… |
| 1.3.6.1.4.1.20044.10.2.3.2.129.2 | Scalarpm1001lhAlmLineSignalFail | read-only | current | Custom Line Signal Fail :This OID indicates that the line input signal is FAIL. The assertion hysteresis can be customized by the host <Condtype> LINE_SIGNAL_F… |
| 1.3.6.1.4.1.20044.10.2.3.2.129.5 | Scalarpm1001lhAlmLineDegrade | read-only | current | Fixed Line Signal Degrade :This OID indicates that the line input signal is DEGRADE. The assetion hysteresis is fixed to 10-8 (assertion) and 10-9 (de-assertio… |
| 1.3.6.1.4.1.20044.10.2.3.2.208 | Nodepm1001lhAlmlineXfpAlarm1 | |||
| 1.3.6.1.4.1.20044.10.2.3.2.208.1 | Scalarpm1001lhAlmLineTxPowerLowAlarm | read-only | current | Line Optical Tx Power Low Alarm :Alarm indicating that the XFP/OTX transmitter transmitter output power is lower than the threshold value written in the XFP/OT… |
| 1.3.6.1.4.1.20044.10.2.3.2.208.2 | Scalarpm1001lhAlmLineTxPowerHighAlarm | read-only | current | Line Optical Tx Power High Alarm :Alarm indicating that the XFP/OTX transmitter transmitter output power is higher than the threshold value written in the XFP … |
| 1.3.6.1.4.1.20044.10.2.3.2.208.3 | Scalarpm1001lhAlmLineTxBiasLowAlarm | read-only | current | Line Transceiver Bias Low Alarm :Alarm indicating that the XFP/OTX transmitter laser bias current is lower than the threshold value written in the XFP/OTX EEPR… |
| 1.3.6.1.4.1.20044.10.2.3.2.208.4 | Scalarpm1001lhAlmLineTxBiasHighAlarm | read-only | current | Line Transceiver Bias High Alarm :Alarm indicating that the XFP/OTX transmitter laser bias current is higher than the threshold value written in the XFP EEPROM… |
| 1.3.6.1.4.1.20044.10.2.3.2.208.7 | Scalarpm1001lhAlmLineTempLowAlarm | read-only | current | Line Transceiver Temp Low Alarm :Alarm indicating that the XFP/OTX temperature is lower than the threshold value written in the XFP/OTX EEPROM <Condtype> LINE_… |
| 1.3.6.1.4.1.20044.10.2.3.2.208.8 | Scalarpm1001lhAlmLineTempHighAlarm | read-only | current | Line Transceiver Temp High Alarm :Alarm indicating that the XFP/OTX temperature is higher than the threshold value written in the XFP EEPROM <Condtype> LINE_TE… |
| 1.3.6.1.4.1.20044.10.2.3.2.208.15 | Scalarpm1001lhAlmLineRxPowerLowAlarm | read-only | current | Line Optical Rx Power Low Alarm :Alarm indicating that the XFP received optical power is lower than the threshold value written in the XFP EEPROM <Condtype> LI… |
| 1.3.6.1.4.1.20044.10.2.3.2.208.16 | Scalarpm1001lhAlmLineRxPowerHighAlarm | read-only | current | Line Optical Rx Power High Alarm :Alarm indicating that the XFP received optical power is higher than the threshold value written in the XFP EEPROM <Condtype> … |
| 1.3.6.1.4.1.20044.10.2.3.2.212 | Nodepm1001lhAlmlineXfpSupplyAlarm | |||
| 1.3.6.1.4.1.20044.10.2.3.2.212.1 | Scalarpm1001lhAlmLineVee5LowAlarm | read-only | current | VEE5 Power Supply Low Alarm :Alarm indicating the XFP/OTX VEE5 power supply is lower than the threshold written in the EEPROM <Condtype> LINE_VEE5_LOW_ALARM <P… |
| 1.3.6.1.4.1.20044.10.2.3.2.212.2 | Scalarpm1001lhAlmLineVee5HighAlarm | read-only | current | VEE5 Power Supply High Alarm :Alarm indicating the XFP/OTX VEE5 power supply is higher than the threshold written in the EEPROM <Condtype> LINE_VEE5_HIGH_ALARM… |
| 1.3.6.1.4.1.20044.10.2.3.2.212.3 | Scalarpm1001lhAlmLineVcc2LowAlarm | read-only | current | VCC2 Power Supply Low Alarm :Alarm indicating the XFP/OTX VCC2 power supply is lower than the threshold written in the EEPROM <Condtype> LINE_VCC2_LOW_ALARM <P… |
| 1.3.6.1.4.1.20044.10.2.3.2.212.4 | Scalarpm1001lhAlmLineVcc2HighAlarm | read-only | current | VCC2 Power Supply High Alarm :Alarm indicating the XFP/OTX VCC2 power supply is higher than the threshold written in the EEPROM <Condtype> LINE_VCC2_HIGH_ALARM… |
| 1.3.6.1.4.1.20044.10.2.3.2.212.5 | Scalarpm1001lhAlmLineVcc3LowAlarm | read-only | current | VCC3 Power Supply Low Alarm :Alarm indicating the XFP/OTX VCC3 power supply is lower than the threshold written in the EEPROM <Condtype> LINE_VCC3_LOW_ALARM <P… |
| 1.3.6.1.4.1.20044.10.2.3.2.212.6 | Scalarpm1001lhAlmLineVcc3HighAlarm | read-only | current | VCC3 Power Supply High Alarm :Alarm indicating the XFP/OTX VCC3 power supply is higher than the threshold written in the EEPROM <Condtype> LINE_VCC3_HIGH_ALARM… |
| 1.3.6.1.4.1.20044.10.2.3.2.212.7 | Scalarpm1001lhAlmLineVcc5LowAlarm | read-only | current | VCC5 Power Supply Low Alarm :Alarm indicating the XFP/OTX VCC5 power supply is lower than the threshold written in the EEPROM <Condtype> LINE_VCC5_LOW_ALARM <P… |
| 1.3.6.1.4.1.20044.10.2.3.2.212.8 | Scalarpm1001lhAlmLineVcc5HighAlarm | read-only | current | VCC5 Power Supply High Alarm :Alarm indicating the XFP/OTX VCC5 power supply is higher than the threshold written in the EEPROM <Condtype> LINE_VCC5_HIGH_ALARM… |
| 1.3.6.1.4.1.20044.10.2.3.2.212.9 | Scalarpm1001lhAlmLineVee5LowLineWarning | read-only | current | VEE5 Power Supply Low Warning :Warning indicating the XFP/OTX VEE5 power supply is lower than the threshold written in the EEPROM <Condtype> LINE_VEE5_LOW_LINE… |
| 1.3.6.1.4.1.20044.10.2.3.2.212.10 | Scalarpm1001lhAlmLineVee5HighWarning | read-only | current | VEE5 Power Supply High Warning :Warning indicating the XFP/OTX VEE5 power supply is higher than the threshold written in the EEPROM <Condtype> LINE_VEE5_HIGH_W… |
| 1.3.6.1.4.1.20044.10.2.3.2.212.11 | Scalarpm1001lhAlmLineVcc2LowWarning | read-only | current | VCC2 Power Supply Low Warning :Warning indicating the XFP/OTX VCC2 power supply is lower than the threshold written in the EEPROM <Condtype> LINE_VCC2_LOW_WARN… |
| 1.3.6.1.4.1.20044.10.2.3.2.212.12 | Scalarpm1001lhAlmLineVcc2HighWarning | read-only | current | VCC2 Power Supply High Warning :Warning indicating the XFP/OTX VCC2 power supply is higher than the threshold written in the EEPROM <Condtype> LINE_VCC2_HIGH_W… |
| 1.3.6.1.4.1.20044.10.2.3.2.212.13 | Scalarpm1001lhAlmLineVcc3LowWarning | read-only | current | VCC3 Power Supply Low Warning :Warning indicating the XFP/OTX VCC3 power supply is lower than the threshold written in the EEPROM <Condtype> LINE_VCC3_LOW_WARN… |
| 1.3.6.1.4.1.20044.10.2.3.2.212.14 | Scalarpm1001lhAlmLineVcc3HighWarning | read-only | current | VCC3 Power Supply High Warning :Warning indicating the XFP/OTX VCC3 power supply is higher than the threshold written in the EEPROM <Condtype> LINE_VCC3_HIGH_W… |
| 1.3.6.1.4.1.20044.10.2.3.2.212.15 | Scalarpm1001lhAlmLineVcc5LowWarning | read-only | current | VCC5 Power Supply Low Warning :Warning indicating the XFP/OTX VCC5 power supply is lower than the threshold written in the EEPROM <Condtype> LINE_VCC5_LOW_WARN… |
| 1.3.6.1.4.1.20044.10.2.3.2.212.16 | Scalarpm1001lhAlmLineVcc5HighWarning | read-only | current | VCC5 Power Supply High Warning :Warning indicating the XFP/OTX VCC5 power supply is higher than the threshold written in the EEPROM <Condtype> LINE_VCC5_HIGH_W… |
| 1.3.6.1.4.1.20044.10.2.3.2.224 | Nodepm1001lhAlmlineOtxTlhAlarms3 | |||
| 1.3.6.1.4.1.20044.10.2.3.2.224.5 | Scalarpm1001lhAlmLineModulatorAgingHighAla | read-only | current | Line Modulator Aging High Alarm :Alarm indicating the Line OTX TLH modulator aging is higher than the threshold written in the EEPROM <Condtype> LINE_MODULATOR… |
| 1.3.6.1.4.1.20044.10.2.3.2.224.6 | Scalarpm1001lhAlmLineAgingHighAla | read-only | current | Line OTX TLH Aging High Alarm :Alarm indicating the Line OTX TLH aging is higher than the threshold written in the EEPROM <Condtype> LINE_AGING_HIGH_ALA <Probc… |
| 1.3.6.1.4.1.20044.10.2.3.2.224.9 | Scalarpm1001lhAlmLineCdrNotReady | read-only | current | CDR Not Ready :This OID indicates the Clock Data Recovery unit is not yet initialized <Help> This alarm indicates the Clock Data Recovery unit is not yet initi… |
| 1.3.6.1.4.1.20044.10.2.3.2.224.12 | Scalarpm1001lhAlmLineFreqDevHighAla | read-only | current | Line Freq. Deviation High Alarm :Alarm indicating the Line OTX TLH frequency deviation is higher than the threshold written in the EEPROM <Condtype> LINE_FREQ_… |
| 1.3.6.1.4.1.20044.10.2.3.2.224.14 | Scalarpm1001lhAlmLineLaserTempHighAla | read-only | current | Line Laser Temp. High Alarm :Alarm indicating the Line OTX TLH laser temperature is higher than the threshold written in the EEPROM <Condtype> LINE_LASER_TEMP_… |
| 1.3.6.1.4.1.20044.10.2.3.3 | Nodepm1001lhAlmLineCrit | |||
| 1.3.6.1.4.1.20044.10.2.3.3.7 | Nodepm1001lhAlmsynthAlmLine | |||
| 1.3.6.1.4.1.20044.10.2.3.3.7.1 | Scalarpm1001lhAlmLineXfpAbsent | read-only | current | Line Optical Module Absent :This OID indicates that the line optical interface (XFP or OTX) is not plugged in. <Help> This alarm indicates if the line transcei… |
| 1.3.6.1.4.1.20044.10.2.3.3.7.2 | Scalarpm1001lhAlmLineXfpInitNotCompl | read-only | current | Line Optical Module Ready :This OID indicates that the line optical interface (XFP or OTX) is not operational. <Help> This status indicates if the line transce… |
| 1.3.6.1.4.1.20044.10.2.3.3.7.4 | Scalarpm1001lhAlmLineHwFail | read-only | current | Line Port HW Failure :This OID indicates a failure on line port, most probably caused by a HW issue <Condtype> LINE_HW_FAIL <Probcause> equipmentMalfunction (1… |
| 1.3.6.1.4.1.20044.10.2.3.3.7.5 | Scalarpm1001lhAlmLineXfpTxOff | read-only | current | Line Optical Laser Shutdown :This OID indicates the line optical output power is on <Help> This status indicates if the line transceiver laser is ON or OFF <Co… |
| 1.3.6.1.4.1.20044.10.2.3.3.7.6 | Scalarpm1001lhAlmLineLocalOos | read-only | current | Line Port In Service :This OID indicates that the Line port is In Service (1) of Out or Service (2) <Help> This status indicates if the line port is in service… |
| 1.3.6.1.4.1.20044.10.2.3.3.7.8 | Scalarpm1001lhAlmLineUpRdiIns | read-only | current | MS-RDI/L-RDI Inserted On Line :This OID indicates an upstream RDI has been inserted in the outgoing 10 Gb/s signal. <Help> This status indicates if a MS-RDI/L-… |
| 1.3.6.1.4.1.20044.10.2.3.3.7.9 | Scalarpm1001lhAlmLineDdmWarning | read-only | current | Warning On Line Optical Module DDM :This OID indicates a warning is present coming out of Line optical interface DDM <Help> This alarm indicates if a DDM Warni… |
| 1.3.6.1.4.1.20044.10.2.3.3.7.10 | Scalarpm1001lhAlmLineDdmAlm | read-only | current | Alarm On Line Optical Module DDM :This OID indicates an alarm is present coming out of Line optical interface DDM <Help> This alarm indicates if a DDM Alarm ha… |
| 1.3.6.1.4.1.20044.10.2.3.3.7.12 | Scalarpm1001lhAlmLineFail | read-only | current | Line Port Failure :This OID indicates a failure on the line port <Condtype> LINE_FAIL <Probcause> equipmentMalfunction (16) <Alarmtype> synthesisAlarm (12) <Po… |
| 1.3.6.1.4.1.20044.10.2.3.3.128 | Nodepm1001lhAlmdfrmAlm | |||
| 1.3.6.1.4.1.20044.10.2.3.3.128.1 | Scalarpm1001lhAlmLineDwAisDet | read-only | current | MS-AIS/L-AIS Detected On Line Input :This OID indicates that an MS-AIS has been detected on line input signal <Help> This alarm indicates if there is a MS-AIS/… |
| 1.3.6.1.4.1.20044.10.2.3.3.128.2 | Scalarpm1001lhAlmLineDwRdiDet | read-only | current | MS-RDI/L-RDI Detected On Line Input :This OID indicates that an MS-RDI has been detected on line input signal <Help> This alarm indicates if there is a MS-RDI/… |
| 1.3.6.1.4.1.20044.10.2.3.3.128.3 | Scalarpm1001lhAlmLineDwOof | read-only | current | SONET/SDH Line Out Of Frame :This OID indicates that an Out Of Frame has been detected on line input signal <Help> This alarm indicates if a Loss Of Frame is d… |
| 1.3.6.1.4.1.20044.10.2.3.3.128.4 | Scalarpm1001lhAlmLineDwLof | read-only | current | SONET/SDH Line Loss Of Frame :This OID indicates that a Loss Of Frame has been detected on line input signal <Help> This alarm indicates if there is a Loss of … |
| 1.3.6.1.4.1.20044.10.2.3.3.128.5 | Scalarpm1001lhAlmLineFecFail | read-only | current | FEC Decoding Fail :This OID indicates that the FEC decoder is in an overcapacity mode and not able to correct errors <Help> This alarm indicates if the FEC dec… |
| 1.3.6.1.4.1.20044.10.2.3.3.133 | Nodepm1001lhAlmlineSyncAlarms | |||
| 1.3.6.1.4.1.20044.10.2.3.3.133.12 | Scalarpm1001lhAlmLineDwLockerr | read-only | current | Downstream Clock Lock Error :This OID indicates that the deserializer input 10 Gb/s clock recovery is not locked. <Condtype> LINE_DW_LOCKERR <Probcause> receiv… |
| 1.3.6.1.4.1.20044.10.2.3.3.133.13 | Scalarpm1001lhAlmLineUpLockerr | read-only | current | Upstream Clock Lock Error :This OID indicates that the serializer output 10 Gb/s clock multiplier unit is not locked. <Condtype> LINE_UP_LOCKERR <Probcause> re… |
| 1.3.6.1.4.1.20044.10.2.3.3.133.16 | Scalarpm1001lhAlmLineDwLos | read-only | current | Line Input Loss Of Signal :This OID indicates a loss of signal on the 10 Gb/s input. <Help> This alarm indicates if an optical signal is detected on the line t… |
| 1.3.6.1.4.1.20044.10.2.3.3.211 | Nodepm1001lhAlmlineXfpAlarms2 | |||
| 1.3.6.1.4.1.20044.10.2.3.3.211.2 | Scalarpm1001lhAlmLineModNr | read-only | current | Line Optical Module Not Ready :This OID indicates that the module is unable to determine correct data. <Help> This alarm indicates if the line transceiver is r… |
| 1.3.6.1.4.1.20044.10.2.3.3.211.3 | Scalarpm1001lhAlmLineRxCdrNotLocked1 | read-only | current | Line Optical Rx CDR Unlocked :This OID indicates that a loss of lock on the receiving side CDR has been detected <Help> This alarm indicates if the Rx CDR is l… |
| 1.3.6.1.4.1.20044.10.2.3.3.211.5 | Scalarpm1001lhAlmLineRxNr | read-only | current | Line Optical Rx Not Ready :This OID indicates that a condition has arisen leading to invalid data on the receiving side. <Help> This alarm indicates if the Rx … |
| 1.3.6.1.4.1.20044.10.2.3.3.211.6 | Scalarpm1001lhAlmLineTxCdrNotLocked1 | read-only | current | Line Optical Tx CDR Unlocked :This OID indicates a loss of lock on the transmitting side CDR has been detected. <Help> This alarm indicates if the Tx CDR is lo… |
| 1.3.6.1.4.1.20044.10.2.3.3.211.7 | Scalarpm1001lhAlmLineTxFault | read-only | current | Line Optical Tx Failure :This OID indicates a fault condition on the laser detected by the safety syste <Help> This alarm indicates if the laser of the line tr… |
| 1.3.6.1.4.1.20044.10.2.3.3.211.8 | Scalarpm1001lhAlmLineTxNr | read-only | current | Line Optical Tx Not Ready :This OID indicates a condition has arisen leading to invalid data on the transmitting side <Help> This alarm indicates if the Tx par… |
| 1.3.6.1.4.1.20044.10.2.3.3.211.10 | Scalarpm1001lhAlmLineChannelNotAcquired | read-only | current | DWDM Channel Not Acquired :This OID indicates the transceiver didn't tune the DWDM Channel succesfully. <Help> This status indicates the transceiver has not tu… |
| 1.3.6.1.4.1.20044.10.2.3.3.211.14 | Scalarpm1001lhAlmLineWavelengthUnlocked | read-only | current | Line Optical Tx Wavelength Unlock :This OID indicates that the wavelength error is exceeding the manufacturer tolerance <Help> This alarm indicates if the wave… |
| 1.3.6.1.4.1.20044.10.2.3.3.211.15 | Scalarpm1001lhAlmLineTecFault | read-only | current | Line Optical Tx Temp Regul. Failed :This OID indicates a failure on the TEC module <Help> This alarm indicates if the TEC of the line transceiver is in fail co… |
| 1.3.6.1.4.1.20044.10.2.3.3.211.16 | Scalarpm1001lhAlmLineApdSupplyFault | read-only | current | Line Rx Photodiode Power Failed :This OID indicates a failure on the APD power supply <Help> This alarm indicates if the APD power supply is in fail condition … |
| 1.3.6.1.4.1.20044.10.3 | Nodepm1001lhmeasures | |||
| 1.3.6.1.4.1.20044.10.3.1 | Nodepm1001lhMesrOther | |||
| 1.3.6.1.4.1.20044.10.3.1.0 | Scalarpm1001lhMesrsynth0 | read-only | deprecated | Not Used :This OID gives the unit used on AUX1 measurement of XFP#1 (Unit = ) |
| 1.3.6.1.4.1.20044.10.3.1.1 | Scalarpm1001lhMesrsynth1 | read-only | deprecated | Not Used :This OID gives the unit used on AUX2 measurement of XFP#1 (Unit = ) |
| 1.3.6.1.4.1.20044.10.3.2 | Nodepm1001lhMesrClient | |||
| 1.3.6.1.4.1.20044.10.3.2.16 | Scalarpm1001lhMesrclientModTempMeas | read-only | current | Client Optical Module Temperature :This OID gives the temperature value of the XFP plugged in port, read from the DDM (Digital Diagnostic Monitoring) (Temperat… |
| 1.3.6.1.4.1.20044.10.3.2.32 | Scalarpm1001lhMesrclientBiasCurrentMeas | read-only | current | Client Optical Module Laser Bias :This OID gives the bias value of the XFP plugged into port, read from the DDM (Digital Diagnostic Monitoring) (Bias = AV/500)… |
| 1.3.6.1.4.1.20044.10.3.2.40 | Scalarpm1001lhMesrclientTxPowerMeas | read-only | current | Client Optical Module Tx Power :This OID gives the transmit power value of the XFP plugged into port, read from the DDM (Digital Diagnostic Monitoring) (Power … |
| 1.3.6.1.4.1.20044.10.3.2.48 | Scalarpm1001lhMesrclientRxPowerMeas | read-only | current | Client Optical Module Rx Power :This OID gives the receive power value of the XFP plugged into port, read in the DDM (Digital Diagnostic Monitoring) (Power = 1… |
| 1.3.6.1.4.1.20044.10.3.3 | Nodepm1001lhMesrLine | |||
| 1.3.6.1.4.1.20044.10.3.3.208 | Scalarpm1001lhMesrlineModTempMeas | read-only | current | Line Optical Module Temperature :This OID gives the temperature of the XFP or OTX plugged in line#1, read from the DDM (Digital Diagnostic Monitoring) (Tempera… |
| 1.3.6.1.4.1.20044.10.3.3.209 | Scalarpm1001lhMesrlineReserved | read-only | deprecated | Not Used :Reserved |
| 1.3.6.1.4.1.20044.10.3.3.210 | Scalarpm1001lhMesrlineBiasCurrentMeas | read-only | current | Line Optical Module Laser Bias :This OID gives the bias value of the XFP or OTX plugged in line #1, read from the DDM (Digital Diagnostic Monitoring) (Bias = A… |
| 1.3.6.1.4.1.20044.10.3.3.211 | Scalarpm1001lhMesrlineTxPowerMeas | read-only | current | Line Optical Module Tx Power :This OID gives the transmit power value of the XFP or OTX plugged in line #1, read from the DDM (Digital Diagnostic Monitoring) (… |
| 1.3.6.1.4.1.20044.10.3.3.212 | Scalarpm1001lhMesrlineRxPowerMeas | read-only | current | Line Optical Module Rx Power :This OID gives the receive power value of the XFP or OTX plugged in line #1, read from the DDM (Digital Diagnostic Monitoring) (P… |
| 1.3.6.1.4.1.20044.10.3.3.213 | Scalarpm1001lhMesrlineAux1Meas | read-only | deprecated | Not Used :This OID gives the receive power value read in the DDM (Digital Diagnostic Monitoring) of the XFP or OTX plugged in line #1 (Unit = ?) |
| 1.3.6.1.4.1.20044.10.3.3.214 | Scalarpm1001lhMesrlineAux2Meas | read-only | deprecated | Not Used :This OID gives the receive power value read in the DDM (Digital Diagnostic Monitoring) of the XFP or OTX plugged in line #1 (Unit = ?) |
| 1.3.6.1.4.1.20044.10.3.3.224 | Scalarpm1001lhMesrlineAging | read-only | current | Line OTX TLH Aging :This OID gives the aging of the Line OTX TLH, read from the DDM (Digital Diagnostic Monitoring) (Aging = AV) (Unit = %) <Help> This measure… |
| 1.3.6.1.4.1.20044.10.3.3.225 | Scalarpm1001lhMesrlineLaserTemperature | read-only | deprecated | Line OTX TLH Laser Temperature :This OID gives the laser temperature of the Line OTX TLH, read from the DDM (Digital Diagnostic Monitoring) (Temperature = AV/2… |
| 1.3.6.1.4.1.20044.10.3.3.226 | Scalarpm1001lhMesrlineFreqDeviation | read-only | current | Line OTX TLH Frequency Deviation :This OID gives the frequency deviation of the Line OTX TLH, read from the DDM (Digital Diagnostic Monitoring) (Deviation = (A… |
| 1.3.6.1.4.1.20044.10.3.3.227 | Scalarpm1001lhMesrlineLaserWvlength | read-only | current | Line Optical Module Wavelength :This OID gives the laser wavelength of the Line OTX TLH, read from the DDM (Digital Diagnostic Monitoring) (Wavelength=29979245… |
| 1.3.6.1.4.1.20044.10.4 | Nodepm1001lhcounters | |||
| 1.3.6.1.4.1.20044.10.4.1 | Nodepm1001lhCntOther | |||
| 1.3.6.1.4.1.20044.10.4.2 | Nodepm1001lhCntClient | |||
| 1.3.6.1.4.1.20044.10.4.2.32 | Tablepm1001lhCntclientUpErrCntTable | not-accessible | current | List of pm1001lhCntclientUpErrCnt Article |
| 1.3.6.1.4.1.20044.10.4.2.32.1 | Rowpm1001lhCntclientUpErrCntEntry | not-accessible | current | Row definition for the pm1001lhCntclientUpErrCnt table |
| 1.3.6.1.4.1.20044.10.4.2.32.1.1 | Columnpm1001lhCntclientUpErrCntIndex | read-only | current | Index definition for the pm1001lhCntclientUpErrCnt table |
| 1.3.6.1.4.1.20044.10.4.2.32.1.2 | Columnpm1001lhCntclientUpErrCntValuePortn | read-only | current | Client Input Errors :This counter is increased each time a FCS error is detected in 10GbE mode or a B1 error is detected in OC-192/STM-64 mode on the client in… |
| 1.3.6.1.4.1.20044.10.4.2.32.1.3 | Columnpm1001lhCntclientUpErrCntErrorPortn | read-only | current | Client Counter Error :This OID when set indicates the FCS error counter value is invalid on input Port |
| 1.3.6.1.4.1.20044.10.4.2.32.1.4 | Columnpm1001lhCntclientUpErrCntOverloadPortn | read-only | current | Client Counter Overload :This OID when set indicates a FCS error counter overload on input Port |
| 1.3.6.1.4.1.20044.10.4.2.40 | Tablepm1001lhCntclientUpTimCntTable | not-accessible | current | List of pm1001lhCntclientUpTimCnt Article |
| 1.3.6.1.4.1.20044.10.4.2.40.1 | Rowpm1001lhCntclientUpTimCntEntry | not-accessible | current | Row definition for the pm1001lhCntclientUpTimCnt table |
| 1.3.6.1.4.1.20044.10.4.2.40.1.1 | Columnpm1001lhCntclientUpTimCntIndex | read-only | current | Index definition for the pm1001lhCntclientUpTimCnt table |
| 1.3.6.1.4.1.20044.10.4.2.40.1.2 | Columnpm1001lhCntclientUpTimCntValuePortn | read-only | current | Client Upstream Timer Counter :This is the timing counter dedicated to the upstream access counters. It is incremented every 125 us. |
| 1.3.6.1.4.1.20044.10.4.2.40.1.3 | Columnpm1001lhCntclientUpTimCntErrorPortn | read-only | current | Client Counter Error :This OID when set indicates the upstream timing counter value is invalid on Port |
| 1.3.6.1.4.1.20044.10.4.2.40.1.4 | Columnpm1001lhCntclientUpTimCntOverloadPortn | read-only | current | Client Counter Overload :This OID when set indicates a upstream timing counter overload on Port |
| 1.3.6.1.4.1.20044.10.4.2.64 | Tablepm1001lhCntclientDwErrCntTable | not-accessible | current | List of pm1001lhCntclientDwErrCnt Article |
| 1.3.6.1.4.1.20044.10.4.2.64.1 | Rowpm1001lhCntclientDwErrCntEntry | not-accessible | current | Row definition for the pm1001lhCntclientDwErrCnt table |
| 1.3.6.1.4.1.20044.10.4.2.64.1.1 | Columnpm1001lhCntclientDwErrCntIndex | read-only | current | Index definition for the pm1001lhCntclientDwErrCnt table |
| 1.3.6.1.4.1.20044.10.4.2.64.1.2 | Columnpm1001lhCntclientDwErrCntValuePortn | read-only | current | Client Output Errors :This counter is increased each time a B1/FCS error is detected on the client output stream <Help> This counter gives the number of FCS er… |
| 1.3.6.1.4.1.20044.10.4.2.64.1.3 | Columnpm1001lhCntclientDwErrCntErrorPortn | read-only | current | Client Counter Error :This OID when set indicates the FCS error counter value is invalid on output Port |
| 1.3.6.1.4.1.20044.10.4.2.64.1.4 | Columnpm1001lhCntclientDwErrCntOverloadPortn | read-only | current | Client Counter Overload :This OID when set indicates a FCS error counter overload on output Port |
| 1.3.6.1.4.1.20044.10.4.2.72 | Tablepm1001lhCntclientDwTimCntTable | not-accessible | current | List of pm1001lhCntclientDwTimCnt Article |
| 1.3.6.1.4.1.20044.10.4.2.72.1 | Rowpm1001lhCntclientDwTimCntEntry | not-accessible | current | Row definition for the pm1001lhCntclientDwTimCnt table |
| 1.3.6.1.4.1.20044.10.4.2.72.1.1 | Columnpm1001lhCntclientDwTimCntIndex | read-only | current | Index definition for the pm1001lhCntclientDwTimCnt table |
| 1.3.6.1.4.1.20044.10.4.2.72.1.2 | Columnpm1001lhCntclientDwTimCntValuePortn | read-only | current | Client Downstream Timer Counter :This is the timing counter dedicated to the downstream access counters. It is incremented every 125 us. |
| 1.3.6.1.4.1.20044.10.4.2.72.1.3 | Columnpm1001lhCntclientDwTimCntErrorPortn | read-only | current | Client Counter Error :This OID when set indicates the downstream timer counter value is invalid on Port |
| 1.3.6.1.4.1.20044.10.4.2.72.1.4 | Columnpm1001lhCntclientDwTimCntOverloadPortn | read-only | current | Client Counter Overload :This OID when set indicates a downstream timer counter overload on Port |
| 1.3.6.1.4.1.20044.10.4.3 | Nodepm1001lhCntLine | |||
| 1.3.6.1.4.1.20044.10.4.3.152 | Tablepm1001lhCntlineDfrmErrCntTable | not-accessible | current | List of pm1001lhCntlineDfrmErrCnt Article |
| 1.3.6.1.4.1.20044.10.4.3.152.1 | Rowpm1001lhCntlineDfrmErrCntEntry | not-accessible | current | Row definition for the pm1001lhCntlineDfrmErrCnt table |
| 1.3.6.1.4.1.20044.10.4.3.152.1.1 | Columnpm1001lhCntlineDfrmErrCntIndex | read-only | current | Index definition for the pm1001lhCntlineDfrmErrCnt table |
| 1.3.6.1.4.1.20044.10.4.3.152.1.2 | Columnpm1001lhCntlineDfrmErrCntValuePortn | read-only | current | Line Input B1 Errors :This counter is incremented each time a B1 error is detected on the Deframer input stream. <Help> This counter gives the number of B1 err… |
| 1.3.6.1.4.1.20044.10.4.3.152.1.3 | Columnpm1001lhCntlineDfrmErrCntErrorPortn | read-only | current | Line Counter Error :This OID when set indicates the B1 error counter value is invalid on Port |
| 1.3.6.1.4.1.20044.10.4.3.152.1.4 | Columnpm1001lhCntlineDfrmErrCntOverloadPortn | read-only | current | Line Counter Overload :This OID when set indicates a B1 error counter overload on Port |
| 1.3.6.1.4.1.20044.10.4.3.153 | Tablepm1001lhCntlineDfrmTimCntTable | not-accessible | current | List of pm1001lhCntlineDfrmTimCnt Article |
| 1.3.6.1.4.1.20044.10.4.3.153.1 | Rowpm1001lhCntlineDfrmTimCntEntry | not-accessible | current | Row definition for the pm1001lhCntlineDfrmTimCnt table |
| 1.3.6.1.4.1.20044.10.4.3.153.1.1 | Columnpm1001lhCntlineDfrmTimCntIndex | read-only | current | Index definition for the pm1001lhCntlineDfrmTimCnt table |
| 1.3.6.1.4.1.20044.10.4.3.153.1.2 | Columnpm1001lhCntlineDfrmTimCntValuePortn | read-only | current | Line Timer :This is the timing counter dedicated to the downstream deframer counters. It is incremented every 125 us. |
| 1.3.6.1.4.1.20044.10.4.3.153.1.3 | Columnpm1001lhCntlineDfrmTimCntErrorPortn | read-only | current | Line Counter Error :This OID when set indicates the deframer timer counter value is invalid on Port |
| 1.3.6.1.4.1.20044.10.4.3.153.1.4 | Columnpm1001lhCntlineDfrmTimCntOverloadPortn | read-only | current | Line Counter Overload :This OID when set indicates a deframer timer counter overload on Port |
| 1.3.6.1.4.1.20044.10.4.3.154 | Tablepm1001lhCntlineDfrmPrimErrCntTable | not-accessible | current | List of pm1001lhCntlineDfrmPrimErrCnt Article |
| 1.3.6.1.4.1.20044.10.4.3.154.1 | Rowpm1001lhCntlineDfrmPrimErrCntEntry | not-accessible | current | Row definition for the pm1001lhCntlineDfrmPrimErrCnt table |
| 1.3.6.1.4.1.20044.10.4.3.154.1.1 | Columnpm1001lhCntlineDfrmPrimErrCntIndex | read-only | current | Index definition for the pm1001lhCntlineDfrmPrimErrCnt table |
| 1.3.6.1.4.1.20044.10.4.3.154.1.2 | Columnpm1001lhCntlineDfrmPrimErrCntValuePortn | read-only | current | Line Input FEC Corrected Errors :This counter is incremented each time an error is corrected by the Forward Error Correction decoder <Help> This counter gives … |
| 1.3.6.1.4.1.20044.10.4.3.154.1.3 | Columnpm1001lhCntlineDfrmPrimErrCntErrorPortn | read-only | current | Line FEC Counter Error :This bit when set indicates the FEC counter value is invalid on Port |
| 1.3.6.1.4.1.20044.10.4.3.154.1.4 | Columnpm1001lhCntlineDfrmPrimErrCntOverloadPortn | read-only | current | Line FEC Counter Overload :This bit when set indicates a FEC counter overload on Port |
| 1.3.6.1.4.1.20044.10.4.3.1160 | Tablepm1001lhCntlineDfrmErrCntSTable | not-accessible | current | List of pm1001lhCntlineDfrmErrCntS Article |
| 1.3.6.1.4.1.20044.10.4.3.1160.1 | Rowpm1001lhCntlineDfrmErrCntSEntry | not-accessible | current | Row definition for the pm1001lhCntlineDfrmErrCntS table |
| 1.3.6.1.4.1.20044.10.4.3.1160.1.1 | Columnpm1001lhCntlineDfrmErrCntSIndex | read-only | current | Index definition for the pm1001lhCntlineDfrmErrCntS table |
| 1.3.6.1.4.1.20044.10.4.3.1160.1.2 | Columnpm1001lhCntlineDfrmErrCntSValuePortn | read-only | current | Line B1 error rate (/s) :This OID gives the number of B1 errors per second that are detected on the Deframer input stream. |
| 1.3.6.1.4.1.20044.10.4.3.1160.1.3 | Columnpm1001lhCntlineDfrmErrCntSErrorPortn | read-only | current | |
| 1.3.6.1.4.1.20044.10.4.3.1160.1.4 | Columnpm1001lhCntlineDfrmErrCntSOverloadPortn | read-only | current | |
| 1.3.6.1.4.1.20044.10.4.259 | Scalarpm1001lhCntCountersReset | read-write | current | Counters Reset:This OID resets and restarts all the counters |
| 1.3.6.1.4.1.20044.10.4.260 | Scalarpm1001lhCntCountersStop | read-write | current | Counters stop:This OID stops all the counters |
| 1.3.6.1.4.1.20044.10.6 | Nodepm1001lhcontrolsWrite | |||
| 1.3.6.1.4.1.20044.10.6.1 | Nodepm1001lhCtrlOther | |||
| 1.3.6.1.4.1.20044.10.6.1.1 | Nodepm1001lhCtrlconfMgnt1 | |||
| 1.3.6.1.4.1.20044.10.6.1.1.1 | Scalarpm1001lhCtrlConf1Load1 | read-write | current | Load Configuration Tables Set Nb 1 :When set this OID enables loading from flash configuration1 into the PM. |
| 1.3.6.1.4.1.20044.10.6.1.1.2 | Scalarpm1001lhCtrlConf2Load1 | read-write | current | Load Configuration Tables Set Nb 2 :When set this OID enables loading from flash configuration2 into the PM. |
| 1.3.6.1.4.1.20044.10.6.1.1.10 | Scalarpm1001lhCtrlConf2Flash1 | read-write | current | Write Configuration Tables :This OID saves the current configuration of the PM as configuration2 in the flash. <Help> This control saves the customer configura… |
| 1.3.6.1.4.1.20044.10.6.1.1.14 | Scalarpm1001lhCtrlConf2Clear1 | read-write | current | Clear Configuration Tables :This OID clears the configuration tables from configuration2 in the flash. <Help> This control restores the default configuration o… |
| 1.3.6.1.4.1.20044.10.6.1.4 | Nodepm1001lhCtrlsynth4 | |||
| 1.3.6.1.4.1.20044.10.6.1.4.1 | Scalarpm1001lhCtrlCorrelatOn | read-write | current | Enable Alarm Correlation :This OID enables the alarm correlation in the PM. |
| 1.3.6.1.4.1.20044.10.6.1.4.2 | Scalarpm1001lhCtrlCorrelatOff | read-write | current | Disable Alarm Correlation :This OID disables the alarm correlation in the PM. |
| 1.3.6.1.4.1.20044.10.6.1.5 | Nodepm1001lhCtrlswMgnt | |||
| 1.3.6.1.4.1.20044.10.6.1.5.2 | Scalarpm1001lhCtrlColdReset | read-write | current | PM Cold Reset :This OID, when set, causes a cold reset of the PM. This reset is traffic affecting, and the configuration of PM is reloaded on start-up. <Help> … |
| 1.3.6.1.4.1.20044.10.6.1.5.3 | Scalarpm1001lhCtrlWarmReset | read-write | current | PM Warm Reset :This OID, when set, causes a warm reset of the PM. This reset is not traffic affecting, and the configuration of PM remains unchanged. <Help> Th… |
| 1.3.6.1.4.1.20044.10.6.1.5.5 | Scalarpm1001lhCtrlLoadSwBank1 | read-write | current | Set Software Nb 1 As Active :This OID, when set, loads the SW from bank1 into the PM. It must be followed by a reset. <Help> This controls selects the first SW… |
| 1.3.6.1.4.1.20044.10.6.1.5.6 | Scalarpm1001lhCtrlLoadSwBank2 | read-write | current | Set Software Nb 2 As Active :This OID, when set, loads the SW from bank2 into the PM. It must be followed by a reset. <Help> This controls selects the second S… |
| 1.3.6.1.4.1.20044.10.6.1.6 | Nodepm1001lhCtrlgwMgnt | |||
| 1.3.6.1.4.1.20044.10.6.1.6.1 | Scalarpm1001lhCtrlCurrentGwReset | read-write | current | Active Gateware Reset :This OID, when set, resets the active gateware. It is traffic affecting. |
| 1.3.6.1.4.1.20044.10.6.1.6.5 | Scalarpm1001lhCtrlLoadGwBank1 | read-write | current | Set Gateware Nb 1 As Active :This OID, when set, loads the GW from bank1 (Flash) into the PM. It is followed by an automatic gateware cold reset. <Help> This c… |
| 1.3.6.1.4.1.20044.10.6.1.6.6 | Scalarpm1001lhCtrlLoadGwBank2 | read-write | current | Set Gateware Nb 2 As Active :This OID, when set, loads the GW from bank2 (Flash) into the PM. It is followed by an automatic gateware cold reset. |
| 1.3.6.1.4.1.20044.10.6.1.6.7 | Scalarpm1001lhCtrlLoadGwBank3 | read-write | current | Set Gateware Nb 3 As Active :This OID, when set, loads the GW from bank3 (Flash) into the PM. It is followed by an automatic gateware cold reset. <Help> This c… |
| 1.3.6.1.4.1.20044.10.6.1.6.8 | Scalarpm1001lhCtrlLoadGwBank4 | read-write | current | Set Gateware Nb 4 As Active :This OID, when set, loads the GW from bank4 (Flash) into the PM. It is followed by an automatic gateware cold reset. |
| 1.3.6.1.4.1.20044.10.6.1.192 | Nodepm1001lhCtrlledTest | |||
| 1.3.6.1.4.1.20044.10.6.1.192.1 | Scalarpm1001lhCtrlGreenLed | read-write | current | Green Leds Test :This OID switches on all the green Leds as a test feature. <Help> This control initiates a test leds turning all the LEDs to green |
| 1.3.6.1.4.1.20044.10.6.1.192.2 | Scalarpm1001lhCtrlRedLed | read-write | current | Red Leds Test :This OID switches on all the red Leds as a test feature. <Help> This control initiates a test leds turning all the LEDs to red |
| 1.3.6.1.4.1.20044.10.6.1.192.3 | Scalarpm1001lhCtrlLedOff | read-write | current | Leds Off :This OID switches off all the Leds as a test feature. <Help> This control initiates a test leds turning all the LEDs to OFF |
| 1.3.6.1.4.1.20044.10.6.1.193 | Nodepm1001lhCtrlmoduleOosMode | |||
| 1.3.6.1.4.1.20044.10.6.1.193.1 | Scalarpm1001lhCtrlModuleOosMode | read-write | current | PM Out Of Service :This OID sets the PM1008 Out Of Service <Help> This control defines the service state of the complete module |
| 1.3.6.1.4.1.20044.10.6.1.197 | Nodepm1001lhCtrlmaintenanceMode | |||
| 1.3.6.1.4.1.20044.10.6.1.197.1 | Scalarpm1001lhCtrlMaintenanceMode | read-write | current | Module Maintenance Mode :This OID enables the maintenance mode on the PM. <Help> This control enables the maintenance mode on the PM. |
| 1.3.6.1.4.1.20044.10.6.1.198 | Nodepm1001lhCtrldccEnable | |||
| 1.3.6.1.4.1.20044.10.6.1.198.1 | Scalarpm1001lhCtrlDccEnable | read-write | current | DCC Enable :This OID enables the DCC mode on the PM <Help> This control enables the DCC mode on the PM |
| 1.3.6.1.4.1.20044.10.6.2 | Nodepm1001lhCtrlClient | |||
| 1.3.6.1.4.1.20044.10.6.2.16 | Tablepm1001lhCtrlaccessLoopTable | not-accessible | current | List of pm1001lhCtrlaccessLoop Article |
| 1.3.6.1.4.1.20044.10.6.2.16.1 | Rowpm1001lhCtrlaccessLoopEntry | not-accessible | current | Row definition for the pm1001lhCtrlaccessLoop table |
| 1.3.6.1.4.1.20044.10.6.2.16.1.1 | Columnpm1001lhCtrlaccessLoopIndex | read-only | current | Index definition for the pm1001lhCtrlaccessLoop table |
| 1.3.6.1.4.1.20044.10.6.2.16.1.2 | Columnpm1001lhCtrlaccessLoopPortn | read-write | current | Client Facility Loopback :This OID operates a Client Facility Loopback, looping client input signal on the client output port. The loop is located on the clien… |
| 1.3.6.1.4.1.20044.10.6.2.18 | Tablepm1001lhCtrlportOosModeTable | not-accessible | current | List of pm1001lhCtrlportOosMode Article |
| 1.3.6.1.4.1.20044.10.6.2.18.1 | Rowpm1001lhCtrlportOosModeEntry | not-accessible | current | Row definition for the pm1001lhCtrlportOosMode table |
| 1.3.6.1.4.1.20044.10.6.2.18.1.1 | Columnpm1001lhCtrlportOosModeIndex | read-only | current | Index definition for the pm1001lhCtrlportOosMode table |
| 1.3.6.1.4.1.20044.10.6.2.18.1.2 | Columnpm1001lhCtrlportOosModePortn | read-write | current | Client Port Out Of Service :This OID sets the client port Out Of Service <Help> This controls defines the service state of the client port |
| 1.3.6.1.4.1.20044.10.6.2.20 | Tablepm1001lhCtrlxfpOffCtrlTable | not-accessible | current | List of pm1001lhCtrlxfpOffCtrl Article |
| 1.3.6.1.4.1.20044.10.6.2.20.1 | Rowpm1001lhCtrlxfpOffCtrlEntry | not-accessible | current | Row definition for the pm1001lhCtrlxfpOffCtrl table |
| 1.3.6.1.4.1.20044.10.6.2.20.1.1 | Columnpm1001lhCtrlxfpOffCtrlIndex | read-only | current | Index definition for the pm1001lhCtrlxfpOffCtrl table |
| 1.3.6.1.4.1.20044.10.6.2.20.1.2 | Columnpm1001lhCtrlxfpOffCtrlPortn | read-write | current | Client SFP Laser Shutdown :This OID switches off the XFP. <Help> This control defines the laser state of the client transceiver |
| 1.3.6.1.4.1.20044.10.6.2.21 | Tablepm1001lhCtrlcsfUpInsTable | not-accessible | current | List of pm1001lhCtrlcsfUpIns Article |
| 1.3.6.1.4.1.20044.10.6.2.21.1 | Rowpm1001lhCtrlcsfUpInsEntry | not-accessible | current | Row definition for the pm1001lhCtrlcsfUpIns table |
| 1.3.6.1.4.1.20044.10.6.2.21.1.1 | Columnpm1001lhCtrlcsfUpInsIndex | read-only | current | Index definition for the pm1001lhCtrlcsfUpIns table |
| 1.3.6.1.4.1.20044.10.6.2.21.1.2 | Columnpm1001lhCtrlcsfUpInsPortn | read-write | current | Client Signal Fail Insertion :This OID, when set, inserts a client signal fail in the upstream client Port. <Help> This control inserts a Client Signal Fail fo… |
| 1.3.6.1.4.1.20044.10.6.2.22 | Tablepm1001lhCtrlcaisDwInsTable | not-accessible | current | List of pm1001lhCtrlcaisDwIns Article |
| 1.3.6.1.4.1.20044.10.6.2.22.1 | Rowpm1001lhCtrlcaisDwInsEntry | not-accessible | current | Row definition for the pm1001lhCtrlcaisDwIns table |
| 1.3.6.1.4.1.20044.10.6.2.22.1.1 | Columnpm1001lhCtrlcaisDwInsIndex | read-only | current | Index definition for the pm1001lhCtrlcaisDwIns table |
| 1.3.6.1.4.1.20044.10.6.2.22.1.2 | Columnpm1001lhCtrlcaisDwInsPortn | read-write | current | Client AIS Insertion :This OID, when set, inserts a client AIS on the downstream client Port. <Help> This control inserts a Client AIS for the client port |
| 1.3.6.1.4.1.20044.10.6.2.26 | Tablepm1001lhCtrlclientAccessTermLoopTable | not-accessible | current | List of pm1001lhCtrlclientAccessTermLoop Article |
| 1.3.6.1.4.1.20044.10.6.2.26.1 | Rowpm1001lhCtrlclientAccessTermLoopEntry | not-accessible | current | Row definition for the pm1001lhCtrlclientAccessTermLoop table |
| 1.3.6.1.4.1.20044.10.6.2.26.1.1 | Columnpm1001lhCtrlclientAccessTermLoopIndex | read-only | current | Index definition for the pm1001lhCtrlclientAccessTermLoop table |
| 1.3.6.1.4.1.20044.10.6.2.26.1.2 | Columnpm1001lhCtrlclientAccessTermLoopPortn | read-write | current | Client Terminal Loopback :This OID operates a Client Terminal Loopback, looping client input signal on the client output port. The loop is located on the line … |
| 1.3.6.1.4.1.20044.10.6.2.52 | Scalarpm1001lhCtrlprotocol | read-write | current | Client Protocol :This OID sets the protocol of the Client port |
| 1.3.6.1.4.1.20044.10.6.2.271 | Tablepm1001lhCtrlclientResetAllCountTable | not-accessible | current | List of pm1001lhCtrlclientResetAllCount Article |
| 1.3.6.1.4.1.20044.10.6.2.271.1 | Rowpm1001lhCtrlclientResetAllCountEntry | not-accessible | current | Row definition for the pm1001lhCtrlclientResetAllCount table |
| 1.3.6.1.4.1.20044.10.6.2.271.1.1 | Columnpm1001lhCtrlclientResetAllCountIndex | read-only | current | Index definition for the pm1001lhCtrlclientResetAllCount table |
| 1.3.6.1.4.1.20044.10.6.2.271.1.2 | Columnpm1001lhCtrlclientResetAllCountsPortn | read-write | current | Client Counters Reset :This OID resets every counter on the client port <Help> This control operates a reset on the statistics current ,previous and history cl… |
| 1.3.6.1.4.1.20044.10.6.3 | Nodepm1001lhCtrlLine | |||
| 1.3.6.1.4.1.20044.10.6.3.64 | Nodepm1001lhCtrlcommAccessLoop | |||
| 1.3.6.1.4.1.20044.10.6.3.64.1 | Scalarpm1001lhCtrlCommAccessloop | read-write | deprecated | PM Full Access Loop Mode :This OID, when set, puts the module in common access loop back, looping the 10 Gb/s output signal on the 10 Gb/s input. |
| 1.3.6.1.4.1.20044.10.6.3.66 | Nodepm1001lhCtrllineLoop | |||
| 1.3.6.1.4.1.20044.10.6.3.66.1 | Scalarpm1001lhCtrlLineLoop | read-write | deprecated | PM Line Loop Mode :This OID, when set at '1' puts the module in line loopback mode, looping the received 10 Gb/s signal on the transmit 10 Gb/s output. The Ups… |
| 1.3.6.1.4.1.20044.10.6.3.67 | Nodepm1001lhCtrlmsAis | |||
| 1.3.6.1.4.1.20044.10.6.3.67.1 | Scalarpm1001lhCtrlMsAis | read-write | current | Insert MS-AIS/L-AIS On Line Output :This OID, when set, inserts an MS-AIS/L-AIS in the outgoing STM-64/OC-192 signal. |
| 1.3.6.1.4.1.20044.10.6.3.69 | Nodepm1001lhCtrlfecDisable | |||
| 1.3.6.1.4.1.20044.10.6.3.69.1 | Scalarpm1001lhCtrlFecInhibition | read-write | current | FEC Disable :This OID disable the Forward Error Correction decoder on the line receive side <Help> This control disables the Forward Error Correction on the li… |
| 1.3.6.1.4.1.20044.10.6.3.74 | Nodepm1001lhCtrllineOosMode | |||
| 1.3.6.1.4.1.20044.10.6.3.74.1 | Scalarpm1001lhCtrlLineOosMode | read-write | current | Line Port Out Of Service :This OID sets the line port Out Of Service <Help> This control defines the service state of the line port |
| 1.3.6.1.4.1.20044.10.6.3.208 | Tablepm1001lhCtrlxfpOnoffTable | not-accessible | current | List of pm1001lhCtrlxfpOnoff Article |
| 1.3.6.1.4.1.20044.10.6.3.208.1 | Rowpm1001lhCtrlxfpOnoffEntry | not-accessible | current | Row definition for the pm1001lhCtrlxfpOnoff table |
| 1.3.6.1.4.1.20044.10.6.3.208.1.1 | Columnpm1001lhCtrlxfpOnoffIndex | read-only | current | Index definition for the pm1001lhCtrlxfpOnoff table |
| 1.3.6.1.4.1.20044.10.6.3.208.1.2 | Columnpm1001lhCtrlxfpOnoffPortn | read-write | current | Line Optical Laser Shutdown :This OID switches off the XFP or the OTX <Help> This control defines the laser state of the line transceiver |
| 1.3.6.1.4.1.20044.10.6.3.209 | Tablepm1001lhCtrlxfpLineLoopTable | not-accessible | current | List of pm1001lhCtrlxfpLineLoop Article |
| 1.3.6.1.4.1.20044.10.6.3.209.1 | Rowpm1001lhCtrlxfpLineLoopEntry | not-accessible | current | Row definition for the pm1001lhCtrlxfpLineLoop table |
| 1.3.6.1.4.1.20044.10.6.3.209.1.1 | Columnpm1001lhCtrlxfpLineLoopIndex | read-only | current | Index definition for the pm1001lhCtrlxfpLineLoop table |
| 1.3.6.1.4.1.20044.10.6.3.209.1.2 | Columnpm1001lhCtrlxfpLineLoopPortn | read-write | current | Line XFP/OTX Loop :This OID operates a line loopback on the line XFP or the OTX <Help> This control defines the line loop back of the line transceiver |
| 1.3.6.1.4.1.20044.10.6.3.210 | Tablepm1001lhCtrlxfpLineXfiLoopTable | not-accessible | current | List of pm1001lhCtrlxfpLineXfiLoop Article |
| 1.3.6.1.4.1.20044.10.6.3.210.1 | Rowpm1001lhCtrlxfpLineXfiLoopEntry | not-accessible | current | Row definition for the pm1001lhCtrlxfpLineXfiLoop table |
| 1.3.6.1.4.1.20044.10.6.3.210.1.1 | Columnpm1001lhCtrlxfpLineXfiLoopIndex | read-only | current | Index definition for the pm1001lhCtrlxfpLineXfiLoop table |
| 1.3.6.1.4.1.20044.10.6.3.210.1.2 | Columnpm1001lhCtrlxfpLineXfiLoopPortn | read-write | current | Line XFP/OTX XFI Loop :This OID operates a XFI loopback on the line XFP or the OTX <Help> This control defines the XFI loop back of the line transceiver |
| 1.3.6.1.4.1.20044.10.6.3.212 | Scalarpm1001lhCtrllineTunableChannel | read-write | current | ITU Channel :This OID selects the ITU channel of the Line OTX TLH Laser <Help> This control defines the ITU channel of the Line OTX TLH Laser |
| 1.3.6.1.4.1.20044.10.6.3.213 | Scalarpm1001lhCtrllinePhotodiodeMode | read-write | current | OTX TLH Rx Sens. Mode :This OID defines the Rx sensiblity mode of the Line OTX TLH <Help> This control defines the receiver sensibility mode of the Line OTX TL… |
| 1.3.6.1.4.1.20044.10.6.3.214 | Scalarpm1001lhCtrllinePhotodiodeValue | read-write | current | OTX TLH Rx Sensibility :This OID sets the Rx sensibility of the Line OTX TLH (custom mode only) <Help> This control defines the receiver sensibility value (onl… |
| 1.3.6.1.4.1.20044.10.6.3.215 | Scalarpm1001lhCtrllinePowerLaser | read-write | current | Line Laser Output Power [3-5] :This OID sets the output power value on the laser of the Line OTX TLH (AV=Power*10+158) (Unit = dBm) <Help> This control defines… |
| 1.3.6.1.4.1.20044.10.6.3.216 | Nodepm1001lhCtrlotxVlhReset | |||
| 1.3.6.1.4.1.20044.10.6.3.216.1 | Scalarpm1001lhCtrlOtxVlhReset | read-write | current | OTX-VLH Reset :This OID resets the OTX-VLH module <Help> This control resets the OTX-VLH and its parameters |
| 1.3.6.1.4.1.20044.10.6.3.217 | Tablepm1001lhCtrllineAccessLoopTable | not-accessible | current | List of pm1001lhCtrllineAccessLoop Article |
| 1.3.6.1.4.1.20044.10.6.3.217.1 | Rowpm1001lhCtrllineAccessLoopEntry | not-accessible | current | Row definition for the pm1001lhCtrllineAccessLoop table |
| 1.3.6.1.4.1.20044.10.6.3.217.1.1 | Columnpm1001lhCtrllineAccessLoopIndex | read-only | current | Index definition for the pm1001lhCtrllineAccessLoop table |
| 1.3.6.1.4.1.20044.10.6.3.217.1.2 | Columnpm1001lhCtrllineAccessLoopPortn | read-write | current | Line Facility Loopback :This OID operates a Line Facility Loopback, looping line input signal on the line output port. The loop is located on the line transcei… |
| 1.3.6.1.4.1.20044.10.6.3.218 | Tablepm1001lhCtrllineLoopTransceiverTable | not-accessible | current | List of pm1001lhCtrllineLoopTransceiver Article |
| 1.3.6.1.4.1.20044.10.6.3.218.1 | Rowpm1001lhCtrllineLoopTransceiverEntry | not-accessible | current | Row definition for the pm1001lhCtrllineLoopTransceiver table |
| 1.3.6.1.4.1.20044.10.6.3.218.1.1 | Columnpm1001lhCtrllineLoopTransceiverIndex | read-only | current | Index definition for the pm1001lhCtrllineLoopTransceiver table |
| 1.3.6.1.4.1.20044.10.6.3.218.1.2 | Columnpm1001lhCtrllineLoopTransceiverPortn | read-write | current | Line Terminal Loopback :This OID operates a Line Terminal Loopback, looping line input signal on the line output port. The loop is located on all client transc… |
| 1.3.6.1.4.1.20044.10.6.3.335 | Tablepm1001lhCtrllineResetAllCountTable | not-accessible | current | List of pm1001lhCtrllineResetAllCount Article |
| 1.3.6.1.4.1.20044.10.6.3.335.1 | Rowpm1001lhCtrllineResetAllCountEntry | not-accessible | current | Row definition for the pm1001lhCtrllineResetAllCount table |
| 1.3.6.1.4.1.20044.10.6.3.335.1.1 | Columnpm1001lhCtrllineResetAllCountIndex | read-only | current | Index definition for the pm1001lhCtrllineResetAllCount table |
| 1.3.6.1.4.1.20044.10.6.3.335.1.2 | Columnpm1001lhCtrllineResetAllCountsPortn | read-write | current | Line Counters Reset :This OID resets every counter on the line port <Help> This control operates a reset on the statistics current ,previous and history line p… |
| 1.3.6.1.4.1.20044.10.7 | Nodepm1001lhri | |||
| 1.3.6.1.4.1.20044.10.7.1 | Nodepm1001lhriTable | |||
| 1.3.6.1.4.1.20044.10.7.2 | Scalarpm1001lhRinvReloadInventory | read-write | current | Reload the inventory: This OID triggers an inventory reload. |
| 1.3.6.1.4.1.20044.10.7.3 | Scalarpm1001lhRinvHwPlatform | read-only | current | HW platform description: This OID contains the description of the Hardware platform. |
| 1.3.6.1.4.1.20044.10.7.4 | Scalarpm1001lhRinvModulePlatform | read-only | current | Module platform description: This OID contains the description of the Module. |
| 1.3.6.1.4.1.20044.10.7.5 | Scalarpm1001lhRinvSwPlatform | read-only | current | SW platform description: This OID contains the description of the Software platform. |
| 1.3.6.1.4.1.20044.10.7.6 | Scalarpm1001lhRinvGwPlatform | read-only | current | GW platform desciption: This OID contains the description of the Gateware platform. |
| 1.3.6.1.4.1.20044.10.7.7 | Scalarpm1001lhRinvClient | read-only | current | Inventory for the Client port: This OID contains the inventory for the Client port. |
| 1.3.6.1.4.1.20044.10.7.8 | Scalarpm1001lhRinvLine | read-only | current | Inventory for the Line: This OID contains the inventory for the Line. |
| 1.3.6.1.4.1.20044.10.8 | Nodepm1001lhdownload | |||
| 1.3.6.1.4.1.20044.10.8.1 | Nodepm1001lhDwlOther | |||
| 1.3.6.1.4.1.20044.10.8.1.0 | Nodepm1001lhDwlrestartProcess | |||
| 1.3.6.1.4.1.20044.10.8.1.0.1 | Scalarpm1001lhDwlWarmRestartProcessed | read-only | current | Warm Restart :This OID indicates that the module last restart was a Warm RESTART |
| 1.3.6.1.4.1.20044.10.8.1.0.2 | Scalarpm1001lhDwlColdRestartProcessed | read-only | current | Cold Restart :This OID indicates that the module last restart was a Cold RESTART |
| 1.3.6.1.4.1.20044.10.8.1.1 | Nodepm1001lhDwlswBanksUsed | |||
| 1.3.6.1.4.1.20044.10.8.1.1.1 | Scalarpm1001lhDwlSwBank1Used | read-only | current | SW bank 1 active :This OID indicates the module is working on SW bank 1 <Help> This status indicates if the SW bank 1 is active or standby |
| 1.3.6.1.4.1.20044.10.8.1.1.2 | Scalarpm1001lhDwlSwBank2Used | read-only | current | SW bank 2 active :This OID indicates the module is working on SW bank 2 <Help> This status indicates if the SW bank 2 is active or standby |
| 1.3.6.1.4.1.20044.10.8.1.1.5 | Scalarpm1001lhDwlSwBank1Notempty | read-only | current | SW bank 1 loaded :This OID indicates a software is loaded in SW bank 1 <Help> This status indicates if the SW bank 1 contains SW package |
| 1.3.6.1.4.1.20044.10.8.1.1.6 | Scalarpm1001lhDwlSwBank2Notempty | read-only | current | SW bank 2 loaded :This OID indicates a software is loaded in SW bank 2 <Help> This status indicates if the SW bank 2 contains SW package |
| 1.3.6.1.4.1.20044.10.8.1.2 | Nodepm1001lhDwlgwBanksUsed | |||
| 1.3.6.1.4.1.20044.10.8.1.2.1 | Scalarpm1001lhDwlGwBank1Used | read-only | current | GW bank 1 active :This OID indicates the module is working on GW bank 1 <Help> This status indicates if the GW bank 1 is active or standby |
| 1.3.6.1.4.1.20044.10.8.1.2.2 | Scalarpm1001lhDwlGwBank2Used | read-only | deprecated | GW bank 2 active :This OID indicates the module is working on GW bank 2 |
| 1.3.6.1.4.1.20044.10.8.1.2.3 | Scalarpm1001lhDwlGwBank3Used | read-only | current | GW bank 3 active :This OID indicates the module is working on GW bank 3 <Help> This status indicates if the GW bank 3 is active or standby |
| 1.3.6.1.4.1.20044.10.8.1.2.4 | Scalarpm1001lhDwlGwBank4Used | read-only | deprecated | GW bank 4 active :This OID indicates the module is working on GW bank 4 |
| 1.3.6.1.4.1.20044.10.8.1.2.5 | Scalarpm1001lhDwlGwBank1Notempty | read-only | current | GW bank 1 loaded :This OID indicates a gateware is loaded in GW bank 1 <Help> This status indicates if the GW bank 1 contains GW package |
| 1.3.6.1.4.1.20044.10.8.1.2.6 | Scalarpm1001lhDwlGwBank2Notempty | read-only | deprecated | GW bank 2 loaded :This OID indicates a gateware is loaded in GW bank 2 |
| 1.3.6.1.4.1.20044.10.8.1.2.7 | Scalarpm1001lhDwlGwBank3Notempty | read-only | current | GW bank 3 loaded :This OID indicates a gateware is loaded in GW bank 3 <Help> This status indicates if the GW bank 3 contains GW package |
| 1.3.6.1.4.1.20044.10.8.1.2.8 | Scalarpm1001lhDwlGwBank4Notempty | read-only | deprecated | GW bank 4 loaded :This OID indicates a gateware is loaded in GW bank 4 |
| 1.3.6.1.4.1.20044.10.8.2 | Nodepm1001lhDwlClient | |||
| 1.3.6.1.4.1.20044.10.8.3 | Nodepm1001lhDwlLine | |||
| 1.3.6.1.4.1.20044.10.10 | Nodepm1001lhConfig | |||
| 1.3.6.1.4.1.20044.10.10.1 | Nodepm1001lhCfgAccessCAisCsf | |||
| 1.3.6.1.4.1.20044.10.10.1.1 | Tablepm1001lhCfgClientcaiscsfTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.10.10.1.1.1 | Rowpm1001lhCfgClientcaiscsfEntry | not-accessible | current | Row definition for the accessCAisCsf table |
| 1.3.6.1.4.1.20044.10.10.1.1.1.1 | Columnpm1001lhCfgClientcaiscsfIndex | read-only | current | Index definition for the clientcaiscsf table |
| 1.3.6.1.4.1.20044.10.10.1.1.1.3 | Columnpm1001lhCfgCAisModePortn | read-write | current | CAIS mode on Client Port :This register enables/disables port laser shutdown on CAIS insertion condition |
| 1.3.6.1.4.1.20044.10.10.1.1.1.9 | Columnpm1001lhCfgUpAccessioAlmPortn | read-write | current | CSF contributors on Client Port :This register configures the contributors to upstream CSF insertion on the port. |
| 1.3.6.1.4.1.20044.10.10.1.1.1.10 | Columnpm1001lhCfgUpMapperDeAlmPortn | read-write | current | CSF contributors on Client Port :This register configures the contributors to upstream CSF insertion on the port. |
| 1.3.6.1.4.1.20044.10.10.1.1.1.17 | Columnpm1001lhCfgDownAccessioAlmPortn | read-write | current | CAIS contributors on Client Port :This register configures the contributors to downstream CAIS insertion on port. |
| 1.3.6.1.4.1.20044.10.10.1.1.1.18 | Columnpm1001lhCfgDownMapperDeAlmPortn | read-write | current | CAIS contributors on Client Port :This register configures the contributors to downstream CAIS insertion on port. |
| 1.3.6.1.4.1.20044.10.10.1.1.1.19 | Columnpm1001lhCfgDownDfrmAlmPortn | read-write | current | CAIS contributors on Client Port :This register configures the contributors to downstream CAIS insertion on port. |
| 1.3.6.1.4.1.20044.10.10.1.1.1.20 | Columnpm1001lhCfgDownLineSyncAlarmsPortn | read-write | deprecated | CAIS contributors on Client Port :This register configures the contributors to downstream CAIS insertion on port. |
| 1.3.6.1.4.1.20044.10.10.2 | Nodepm1001lhCfgStartup | |||
| 1.3.6.1.4.1.20044.10.10.2.1 | Tablepm1001lhCfgClientStartupTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.10.10.2.1.1 | Rowpm1001lhCfgClientStartupEntry | not-accessible | current | Row definition for the startup table |
| 1.3.6.1.4.1.20044.10.10.2.1.1.1 | Columnpm1001lhCfgClientStartupIndex | read-only | current | Index definition for the clientStartup table |
| 1.3.6.1.4.1.20044.10.10.2.1.1.3 | Columnpm1001lhCfgSystConfPortPortn | read-write | current | Default Settings on Client Port :This register configures the default initialisation settings on the port. |
| 1.3.6.1.4.1.20044.10.10.2.1.1.4 | Columnpm1001lhCfgNetConfPortPortn | read-write | current | Default Protocol on Client Port :This register configures the default initialisation protocol on the port. |
| 1.3.6.1.4.1.20044.10.10.2.1.1.6 | Columnpm1001lhCfgPortsOptionsPortn | read-write | current | Default Options on Client Port :This register configures the default options on the client port |
| 1.3.6.1.4.1.20044.10.10.2.2 | Nodepm1001lhtablelineStartup | |||
| 1.3.6.1.4.1.20044.10.10.2.2.2 | Scalarpm1001lhCfgsynthTransLine | read-write | current | Default Settings on Line 1 :This register configures the default initialisation settings on Line port 1. |
| 1.3.6.1.4.1.20044.10.10.2.2.5 | Scalarpm1001lhCfglineOptions1 | read-write | current | Default Options on Active Line Port :This register configures the default options on the active line port |
| 1.3.6.1.4.1.20044.10.10.2.3 | Tablepm1001lhCfgXfpTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.10.10.2.3.1 | Rowpm1001lhCfgXfpEntry | not-accessible | current | Row definition for the startup table |
| 1.3.6.1.4.1.20044.10.10.2.3.1.1 | Columnpm1001lhCfgXfpIndex | read-only | current | Index definition for the xfp table |
| 1.3.6.1.4.1.20044.10.10.2.3.1.3 | Columnpm1001lhCfgSystConfXfpPortn | read-write | current | Default settings on XFP Port :This register configures the default initialisation settings on XFP port. |
| 1.3.6.1.4.1.20044.10.10.2.3.1.4 | Columnpm1001lhCfgDataRateConfXfpPortn | read-write | deprecated | :Reserved |
| 1.3.6.1.4.1.20044.10.10.2.4 | Tablepm1001lhCfgOtxtlhTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.10.10.2.4.1 | Rowpm1001lhCfgOtxtlhEntry | not-accessible | current | Row definition for the startup table |
| 1.3.6.1.4.1.20044.10.10.2.4.1.1 | Columnpm1001lhCfgOtxtlhIndex | read-only | current | Index definition for the otxtlh table |
| 1.3.6.1.4.1.20044.10.10.2.4.1.3 | Columnpm1001lhCfgLineOtxMiscPortn | read-write | current | Default Line OTX TLH miscellaneous :This register configures the start-up miscellaneous mode of the Line OTX TLH |
| 1.3.6.1.4.1.20044.10.10.2.4.1.4 | Columnpm1001lhCfgLineDitherRatePortn | read-write | current | Default Line OTX TLH FM amplitude :This register configures the start-up width of the frequency modulation of the Line OTX TLH |
| 1.3.6.1.4.1.20044.10.10.2.4.1.5 | Columnpm1001lhCfgLineDitherFhzPortn | read-write | current | Default Line OTX TLH FM frequency :This register configures the start-up frequency of the frequency modulation of the Line OTX TLH |
| 1.3.6.1.4.1.20044.10.10.2.4.1.6 | Columnpm1001lhCfgLinePwrLaserPortn | read-write | current | Defaut Line OTX TLH output Power :This register configures the start-up output power of the Line OTX TLH (Unit = dBm) |
| 1.3.6.1.4.1.20044.10.10.2.4.1.7 | Columnpm1001lhCfgLineFCurrentPortn | read-write | current | Default Line OTX TLH Channel :This register configures the start-up laser channel of the Line OTX TLH |
| 1.3.6.1.4.1.20044.10.10.2.4.1.8 | Columnpm1001lhCfgLineGridCurrentPortn | read-write | current | Default Line OTX TLH Grid :This register configures the start-up laser grid of the Line OTX TLH |
| 1.3.6.1.4.1.20044.10.10.2.4.1.9 | Columnpm1001lhCfgFPortn | read-write | current | Default Line OTX TLH lowest Freq :This register configures the start-up lowest frequency supported on the Line OTX TLH |
| 1.3.6.1.4.1.20044.10.10.2.4.1.10 | Columnpm1001lhCfgReservedPortn | read-write | deprecated | : |
| 1.3.6.1.4.1.20044.10.10.2.4.1.11 | Columnpm1001lhCfgLinePhotodiodeModePortn | read-write | current | Default Line OTX TLH APD mode :This register configures the start-up APD mode of the Line OTX TLH |
| 1.3.6.1.4.1.20044.10.10.2.4.1.12 | Columnpm1001lhCfgLinePhotodiodeValuePortn | read-write | current | Default Line OTX TLH APD atten. :This register configures the start-up APD attenuation on the Line OTX TLH |
| 1.3.6.1.4.1.20044.10.10.3 | Nodepm1001lhCfgLabels | |||
| 1.3.6.1.4.1.20044.10.10.3.1 | Tablepm1001lhCfgLabelclientTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.10.10.3.1.1 | Rowpm1001lhCfgLabelclientEntry | not-accessible | current | Row definition for the labels table |
| 1.3.6.1.4.1.20044.10.10.3.1.1.1 | Columnpm1001lhCfgLabelclientIndex | read-only | current | Index definition for the labelclient table |
| 1.3.6.1.4.1.20044.10.10.3.1.1.3 | Columnpm1001lhCfgLabelclientPortn | read-write | current | Default settings on the label of the Ports :These registers configures the default initialisation settings of the labels of the ports. |
| 1.3.6.1.4.1.20044.10.10.3.2 | Tablepm1001lhCfgLabellineTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.10.10.3.2.1 | Rowpm1001lhCfgLabellineEntry | not-accessible | current | Row definition for the labels table |
| 1.3.6.1.4.1.20044.10.10.3.2.1.1 | Columnpm1001lhCfgLabellineIndex | read-only | current | Index definition for the labelline table |
| 1.3.6.1.4.1.20044.10.10.3.2.1.3 | Columnpm1001lhCfgLabellinePortn | read-write | current | Default settings on the label of the lines :These registers configures the default initialisation settings of the labels of the lines. |
| 1.3.6.1.4.1.20044.10.10.4 | Nodepm1001lhCfgStartuptablefive | |||
| 1.3.6.1.4.1.20044.10.10.4.1 | Tablepm1001lhCfgOtxtlhcapabilitiesTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.10.10.4.1.1 | Rowpm1001lhCfgOtxtlhcapabilitiesEntry | not-accessible | current | Row definition for the startuptablefive table |
| 1.3.6.1.4.1.20044.10.10.4.1.1.1 | Columnpm1001lhCfgOtxtlhcapabilitiesIndex | read-only | current | Index definition for the otxtlhcapabilities table |
| 1.3.6.1.4.1.20044.10.10.4.1.1.3 | Columnpm1001lhCfgComponentTypePortn | read-only | current | Component parameters :This OID defines the component parameters |
| 1.3.6.1.4.1.20044.10.10.4.1.1.4 | Columnpm1001lhCfgMiscellaneousPortn | read-only | current | Miscellaneous default settings :This OID defines the miscellaneous parameters |
| 1.3.6.1.4.1.20044.10.10.4.1.1.5 | Columnpm1001lhCfgFirstChannelPortn | read-only | current | Number of the first channel of the component :This OID defines the first channel number of the PM |
| 1.3.6.1.4.1.20044.10.10.4.1.1.6 | Columnpm1001lhCfgLastChannelPortn | read-only | current | Number of the last channel of the component :This OID defines the last channel number of the PM |
| 1.3.6.1.4.1.20044.10.10.4.1.1.7 | Columnpm1001lhCfgGridPortn | read-only | current | Grid value of the component :This OID defines the grid of the PM |
| 1.3.6.1.4.1.20044.10.10.257 | Scalarpm1001lhCfgWriteConfiguration | read-write | current | Write configuration to module:This OID writes the complete configuration to the module |
| 1.3.6.1.4.1.20044.10.11 | Nodepm1001lhtraps | |||
| 1.3.6.1.4.1.20044.10.11.1 | Scalarpm1001lhtrapBoardNumber | read-only | current | Last module which generates a trap |
| 1.3.6.1.4.1.20044.10.11.30 | Notificationpm1001lhLineTrapNotUrgentGoesOn | current | Not urgent Line default is activated | |
| 1.3.6.1.4.1.20044.10.11.31 | Notificationpm1001lhLineTrapNotUrgentGoesOff | current | Not urgent Line default disappeared | |
| 1.3.6.1.4.1.20044.10.11.32 | Notificationpm1001lhLineTrapUrgentGoesOn | current | Urgent Line default is activated | |
| 1.3.6.1.4.1.20044.10.11.33 | Notificationpm1001lhLineTrapUrgentGoesOff | current | Urgent Line default disappeared | |
| 1.3.6.1.4.1.20044.10.11.34 | Notificationpm1001lhLineTrapCritGoesOn | current | Critical Line default is activated | |
| 1.3.6.1.4.1.20044.10.11.35 | Notificationpm1001lhLineTrapCritGoesOff | current | Critical Line default disappeared | |
| 1.3.6.1.4.1.20044.10.11.40 | Notificationpm1001lhClientTrapNotUrgentGoesOn | current | Not urgent client default is activated | |
| 1.3.6.1.4.1.20044.10.11.41 | Notificationpm1001lhClientTrapNotUrgentGoesOff | current | Not urgent client default disappeared | |
| 1.3.6.1.4.1.20044.10.11.42 | Notificationpm1001lhClientTrapUrgentGoesOn | current | Urgent client default is activated | |
| 1.3.6.1.4.1.20044.10.11.43 | Notificationpm1001lhClientTrapUrgentGoesOff | current | Urgent client default disappeared | |
| 1.3.6.1.4.1.20044.10.11.44 | Notificationpm1001lhClientTrapCritGoesOn | current | Critical client default is activated | |
| 1.3.6.1.4.1.20044.10.11.45 | Notificationpm1001lhClientTrapCritGoesOff | current | Critical client default disappeared | |
| 1.3.6.1.4.1.20044.10.11.50 | Notificationpm1001lhPowerTrapUrgentGoesOn | current | Urgent power supply default is activated | |
| 1.3.6.1.4.1.20044.10.11.51 | Notificationpm1001lhPowerTrapUrgentGoesOff | current | Urgent power supply default disappeared | |
| 1.3.6.1.4.1.20044.10.12 | Nodepm1001lhMonitoring | |||
| 1.3.6.1.4.1.20044.10.12.1 | Nodepm1001lhMonOther | |||
| 1.3.6.1.4.1.20044.10.12.1.1 | Nodepm1001lhMonSync | |||
| 1.3.6.1.4.1.20044.10.12.1.1.257 | Scalarpm1001lhPerfEnable | read-write | current | Perf. Mon. Enable :This OID enables the Performance Monitoring application |
| 1.3.6.1.4.1.20044.10.12.1.1.259 | Scalarpm1001lhPerf15minSync | read-write | current | Perf. Mon. 15-min sync. :This OID must be used in external synchronisation mode only to send a 15-min synchronisation command |
| 1.3.6.1.4.1.20044.10.12.1.1.260 | Scalarpm1001lhPerf24hSync | read-write | current | Perf. Mon. 24-hours sync. :This OID must be used in external synchronisation mode only to send a 24-hours synchronisation command |
| 1.3.6.1.4.1.20044.10.12.1.2 | Nodepm1001lhMonTimeStamp | |||
| 1.3.6.1.4.1.20044.10.12.1.2.1 | Scalarpm1001lhPerf15MinShort | read-write | current | 15-min period is short :This OID indicates that the 15-min period lasts less than 890 seconds |
| 1.3.6.1.4.1.20044.10.12.1.2.2 | Scalarpm1001lhPerf15MinLong | read-write | current | 15-min period is long :This OID indicates that the 15-min period lasts more than 910 seconds |
| 1.3.6.1.4.1.20044.10.12.1.2.5 | Scalarpm1001lhPerf24HoursShort | read-write | current | 24-hours period is short :This OID indicates that 24-hours period lasts less than 86390 seconds |
| 1.3.6.1.4.1.20044.10.12.1.2.6 | Scalarpm1001lhPerf24HoursLong | read-write | current | 24-hours period is long :This OID indicates that 24-hours period lasts more than 86410 seconds |
| 1.3.6.1.4.1.20044.10.12.1.2.7 | Scalarpm1001lhPerfCurrent15MinElapsedTime | read-write | current | Current 15min period Elapsed Time :This OID gives the number of seconds elapsed in the current 15-minutes period |
| 1.3.6.1.4.1.20044.10.12.1.2.8 | Scalarpm1001lhPerfCurrent24HoursElapsedTime | read-write | current | Current 24hours period Elapsed Time :This OID gives the number of seconds elapsed in the current 24-hours period |
| 1.3.6.1.4.1.20044.10.12.2 | Nodepm1001lhMonClient | |||
| 1.3.6.1.4.1.20044.10.12.2.16 | Tablepm1001lhPerfTelecomClientCurrent15StatTable | not-accessible | current | List of pm1001lhPerfTelecomClientCurrent15Stat Article |
| 1.3.6.1.4.1.20044.10.12.2.16.1 | Rowpm1001lhPerfTelecomClientCurrent15StatEntry | not-accessible | current | Row definition for the pm1001lhPerfTelecomClientCurrent15Stat table |
| 1.3.6.1.4.1.20044.10.12.2.16.1.1 | Columnpm1001lhPerfTelecomClientCurrent15StatIndex | read-only | current | Index definition for the pm1001lhPerfTelecomClientCurrent15Stat table |
| 1.3.6.1.4.1.20044.10.12.2.16.1.2 | Columnpm1001lhPerfTelecomClientCurrent15StatInvCvPortn | read-only | current | Current 15-min CV counter inv. :This OID indicates that the current 15-min Coding Violation counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.16.1.3 | Columnpm1001lhPerfTelecomClientCurrent15StatCvValuePortn | read-only | current | Current 15-min CV counter :This OID gives the current 15-min Coding Violation counter value |
| 1.3.6.1.4.1.20044.10.12.2.16.1.4 | Columnpm1001lhPerfTelecomClientCurrent15StatInvEsPortn | read-only | current | Current 15-min ES counter inv. :This OID indicates that the current 15-min Errored Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.16.1.5 | Columnpm1001lhPerfTelecomClientCurrent15StatEsValuePortn | read-only | current | Current 15-min ES counter :This OID gives the current 15-min Errored Second counter value |
| 1.3.6.1.4.1.20044.10.12.2.16.1.6 | Columnpm1001lhPerfTelecomClientCurrent15StatInvSesPortn | read-only | current | Current 15-min SES counter inv. :This OID indicates that the current 15-min severely Errored Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.16.1.7 | Columnpm1001lhPerfTelecomClientCurrent15StatSesValuePortn | read-only | current | Current 15-min SES counter :This OID gives the current 15-min severely Errored Second counter value |
| 1.3.6.1.4.1.20044.10.12.2.16.1.8 | Columnpm1001lhPerfTelecomClientCurrent15StatInvSefsPortn | read-only | current | Current 15-min SEFS counter inv. :This OID indicates that the current 15-min severely Errored Framing Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.16.1.9 | Columnpm1001lhPerfTelecomClientCurrent15StatSefsValuePortn | read-only | current | Current 15-min SEFS counter :This OID gives the current 15-min severely Errored Framing Second counter value |
| 1.3.6.1.4.1.20044.10.12.2.16.1.10 | Columnpm1001lhPerfTelecomClientCurrent15StatInvUasPortn | read-only | current | Current 15-min UAS counter inv. :This OID indicates that the current 15-min UnAvailable Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.16.1.11 | Columnpm1001lhPerfTelecomClientCurrent15StatUasValuePortn | read-only | current | Current 15-min UAS counter :This OID gives the current 15-min UnAvailable Second counter value |
| 1.3.6.1.4.1.20044.10.12.2.24 | Tablepm1001lhPerfTelecomClientPast15StatHistoryPort1Table | not-accessible | current | List of pm1001lhPerfTelecomClientPast15StatHistory Article |
| 1.3.6.1.4.1.20044.10.12.2.24.1 | Rowpm1001lhPerfTelecomClientPast15StatHistoryPort1Entry | not-accessible | current | Row definition for the pm1001lhPerfTelecomClientPast15StatHistory table |
| 1.3.6.1.4.1.20044.10.12.2.24.1.1 | Columnpm1001lhPerfTelecomClientPast15StatHistoryPort1Index | read-only | current | Index definition for the pm1001lhPerfTelecomClientPast15StatHistory table |
| 1.3.6.1.4.1.20044.10.12.2.24.1.2 | Columnpm1001lhPerfTelecomClientPast15StatHistoryInvCvPort1 | read-only | current | Previous 15-min CV counter inv. :This OID indicates that the previous 15-min Coding Violation counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.24.1.3 | Columnpm1001lhPerfTelecomClientPast15StatHistoryCvValuePort1 | read-only | current | Previous 15-min CV counter :This OID gives the previous 15-min Coding Violation counter value |
| 1.3.6.1.4.1.20044.10.12.2.24.1.4 | Columnpm1001lhPerfTelecomClientPast15StatHistoryInvEsPort1 | read-only | current | Previous 15-min ES counter inv. :This OID indicates that the previous 15-min Errored Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.24.1.5 | Columnpm1001lhPerfTelecomClientPast15StatHistoryEsValuePort1 | read-only | current | Previous 15-min ES counter :This OID gives the previous 15-min Errored Second counter value |
| 1.3.6.1.4.1.20044.10.12.2.24.1.6 | Columnpm1001lhPerfTelecomClientPast15StatHistoryInvSesPort1 | read-only | current | Previous 15-min SES counter inv. :This OID indicates that the previous 15-min severely Errored Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.24.1.7 | Columnpm1001lhPerfTelecomClientPast15StatHistorySesValuePort1 | read-only | current | Previous 15-min SES counter :This OID gives the previous 15-min severely Errored Second counter value |
| 1.3.6.1.4.1.20044.10.12.2.24.1.8 | Columnpm1001lhPerfTelecomClientPast15StatHistoryInvSefsPort1 | read-only | current | Previous 15-min SEFS counter inv. :This OID indicates that the previous 15-min severely Errored Framing Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.24.1.9 | Columnpm1001lhPerfTelecomClientPast15StatHistorySefsValuePort1 | read-only | current | Previous 15-min SEFS counter :This OID gives the previous 15-min severely Errored Framing Second counter value |
| 1.3.6.1.4.1.20044.10.12.2.24.1.10 | Columnpm1001lhPerfTelecomClientPast15StatHistoryInvUasPort1 | read-only | current | Previous 15-min UAS counter inv. :This OID indicates that the previous 15-min UnAvailable Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.24.1.11 | Columnpm1001lhPerfTelecomClientPast15StatHistoryUasValuePort1 | read-only | current | Previous 15-min UAS counter :This OID gives the previous 15-min UnAvailable Second counter value |
| 1.3.6.1.4.1.20044.10.12.2.32 | Tablepm1001lhPerfTelecomClientCurrent24StatTable | not-accessible | current | List of pm1001lhPerfTelecomClientCurrent24Stat Article |
| 1.3.6.1.4.1.20044.10.12.2.32.1 | Rowpm1001lhPerfTelecomClientCurrent24StatEntry | not-accessible | current | Row definition for the pm1001lhPerfTelecomClientCurrent24Stat table |
| 1.3.6.1.4.1.20044.10.12.2.32.1.1 | Columnpm1001lhPerfTelecomClientCurrent24StatIndex | read-only | current | Index definition for the pm1001lhPerfTelecomClientCurrent24Stat table |
| 1.3.6.1.4.1.20044.10.12.2.32.1.2 | Columnpm1001lhPerfTelecomClientCurrent24StatInvCvPortn | read-only | current | Current 24-hours CV counter inv. :This OID indicates that the current 24-hours Coding Violation counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.32.1.3 | Columnpm1001lhPerfTelecomClientCurrent24StatCvValuePortn | read-only | current | Current 24-hours CV counter :This OID gives the current 24-hours Coding Violation counter value |
| 1.3.6.1.4.1.20044.10.12.2.32.1.4 | Columnpm1001lhPerfTelecomClientCurrent24StatInvEsPortn | read-only | current | Current 24-hours ES counter inv. :This OID indicates that the current 24-hours Errored Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.32.1.5 | Columnpm1001lhPerfTelecomClientCurrent24StatEsValuePortn | read-only | current | Current 24-hours ES counter :This OID gives the current 24-hours Errored Second counter value |
| 1.3.6.1.4.1.20044.10.12.2.32.1.6 | Columnpm1001lhPerfTelecomClientCurrent24StatInvSesPortn | read-only | current | Current 24-hours SES counter inv. :This OID indicates that the current 24-hours severely Errored Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.32.1.7 | Columnpm1001lhPerfTelecomClientCurrent24StatSesValuePortn | read-only | current | Current 24-hours SES counter :This OID gives the current 24-hours severely Errored Second counter value |
| 1.3.6.1.4.1.20044.10.12.2.32.1.8 | Columnpm1001lhPerfTelecomClientCurrent24StatInvSefsPortn | read-only | current | Current 24-hours SEFS counter inv. :This OID indicates that the current 24-hours severely Errored Framing Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.32.1.9 | Columnpm1001lhPerfTelecomClientCurrent24StatSefsValuePortn | read-only | current | Current 24-hours SEFS counter :This OID gives the current 24-hours severely Errored Framing Second counter value |
| 1.3.6.1.4.1.20044.10.12.2.32.1.10 | Columnpm1001lhPerfTelecomClientCurrent24StatInvUasPortn | read-only | current | Current 24-hours UAS counter inv. :This OID indicates that the current 24-hours UnAvailable Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.32.1.11 | Columnpm1001lhPerfTelecomClientCurrent24StatUasValuePortn | read-only | current | Current 24-hours UAS counter :This OID gives the current 24-hours UnAvailable Second counter value |
| 1.3.6.1.4.1.20044.10.12.2.40 | Tablepm1001lhPerfTelecomClientPast24StatHistoryPort1Table | not-accessible | current | List of pm1001lhPerfTelecomClientPast24StatHistory Article |
| 1.3.6.1.4.1.20044.10.12.2.40.1 | Rowpm1001lhPerfTelecomClientPast24StatHistoryPort1Entry | not-accessible | current | Row definition for the pm1001lhPerfTelecomClientPast24StatHistory table |
| 1.3.6.1.4.1.20044.10.12.2.40.1.1 | Columnpm1001lhPerfTelecomClientPast24StatHistoryPort1Index | read-only | current | Index definition for the pm1001lhPerfTelecomClientPast24StatHistory table |
| 1.3.6.1.4.1.20044.10.12.2.40.1.2 | Columnpm1001lhPerfTelecomClientPast24StatHistoryInvCvPort1 | read-only | current | Previous 24-hours CV counter inv. :This OID indicates that the previous 24-hours Coding Violation counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.40.1.3 | Columnpm1001lhPerfTelecomClientPast24StatHistoryCvValuePort1 | read-only | current | Previous 24-hours CV counter :This OID gives the previous 24-hours Coding Violation counter value |
| 1.3.6.1.4.1.20044.10.12.2.40.1.4 | Columnpm1001lhPerfTelecomClientPast24StatHistoryInvEsPort1 | read-only | current | Previous 24-hours ES counter inv. :This OID indicates that the previous 24-hours Errored Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.40.1.5 | Columnpm1001lhPerfTelecomClientPast24StatHistoryEsValuePort1 | read-only | current | Previous 24-hours ES counter :This OID gives the previous 24-hours Errored Second counter value |
| 1.3.6.1.4.1.20044.10.12.2.40.1.6 | Columnpm1001lhPerfTelecomClientPast24StatHistoryInvSesPort1 | read-only | current | Previous 24-hours SES counter inv. :This OID indicates that the previous 24-hours severely Errored Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.40.1.7 | Columnpm1001lhPerfTelecomClientPast24StatHistorySesValuePort1 | read-only | current | Previous 24-hours SES counter :This OID gives the previous 24-hours severely Errored Second counter value |
| 1.3.6.1.4.1.20044.10.12.2.40.1.8 | Columnpm1001lhPerfTelecomClientPast24StatHistoryInvSefsPort1 | read-only | current | Previous 24-hours SEFS counter inv. :This OID indicates that the previous 24-hours severely Errored Framing Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.40.1.9 | Columnpm1001lhPerfTelecomClientPast24StatHistorySefsValuePort1 | read-only | current | Previous 24-hours SEFS counter :This OID gives the previous 24-hours severely Errored Framing Second counter value |
| 1.3.6.1.4.1.20044.10.12.2.40.1.10 | Columnpm1001lhPerfTelecomClientPast24StatHistoryInvUasPort1 | read-only | current | Previous 24-hours UAS counter inv. :This OID indicates that the previous 24-hours UnAvailable Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.40.1.11 | Columnpm1001lhPerfTelecomClientPast24StatHistoryUasValuePort1 | read-only | current | Previous 24-hours UAS counter :This OID gives the previous 24-hours UnAvailable Second counter value |
| 1.3.6.1.4.1.20044.10.12.2.256 | Tablepm1001lhPerfDatacomClientCurrent15StatTable | not-accessible | current | List of pm1001lhPerfDatacomClientCurrent15Stat Article |
| 1.3.6.1.4.1.20044.10.12.2.256.1 | Rowpm1001lhPerfDatacomClientCurrent15StatEntry | not-accessible | current | Row definition for the pm1001lhPerfDatacomClientCurrent15Stat table |
| 1.3.6.1.4.1.20044.10.12.2.256.1.1 | Columnpm1001lhPerfDatacomClientCurrent15StatIndex | read-only | current | Index definition for the pm1001lhPerfDatacomClientCurrent15Stat table |
| 1.3.6.1.4.1.20044.10.12.2.256.1.2 | Columnpm1001lhperfdatacomclientCurrent15StatInBytesCountInvPortn | read-only | current | Client Current 15-min Input Bytes counter inv. :This OID indicates that the current 15-min Bytes counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.256.1.3 | Columnpm1001lhperfdatacomclientCurrent15StatInBytesCountPortn | read-only | current | Client Current 15-min Input Bytes counter :This OID gives the current 15-min Bytes counter value |
| 1.3.6.1.4.1.20044.10.12.2.256.1.4 | Columnpm1001lhperfdatacomclientCurrent15StatInCrcCountInvPortn | read-only | current | Client Current 15-min Input CRC counter inv. :This OID indicates that the current 15-min CRC counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.256.1.5 | Columnpm1001lhperfdatacomclientCurrent15StatInCrcCountPortn | read-only | current | Client Current 15-min Input CRC counter :This OID gives the current 15-min CRC counter value |
| 1.3.6.1.4.1.20044.10.12.2.256.1.8 | Columnpm1001lhperfdatacomclientCurrent15StatInBroadcastCountInvPortn | read-only | current | Client Current 15-min Input Broadcast counter inv. :This OID indicates that the current 15-min Broadcast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.256.1.9 | Columnpm1001lhperfdatacomclientCurrent15StatInBroadcastCountPortn | read-only | current | Client Current 15-min Input Broadcast counter :This OID gives the current 15-min Broadcast counter value |
| 1.3.6.1.4.1.20044.10.12.2.256.1.10 | Columnpm1001lhperfdatacomclientCurrent15StatInMulticastCountInvPortn | read-only | current | Client Current 15-min Input Multicast counter inv. :This OID indicates that the current 15-min Multicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.256.1.11 | Columnpm1001lhperfdatacomclientCurrent15StatInMulticastCountPortn | read-only | current | Client Current 15-min Input Multicast counter :This OID gives the current 15-min Multicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.256.1.20 | Columnpm1001lhperfdatacomclientCurrent15StatInUnicastCountInvPortn | read-only | current | Client Current 15-min Input Unicast counter inv. :This OID indicates that the current 15-min Unicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.256.1.21 | Columnpm1001lhperfdatacomclientCurrent15StatInUnicastCountPortn | read-only | current | Client Current 15-min Input Unicast counter :This OID gives the current 15-min Unicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.256.1.22 | Columnpm1001lhperfdatacomclientCurrent15StatInNonunicastCountInvPortn | read-only | current | Client Current 15-min Input Non Unicast counter inv. :This OID indicates that the current 15-min Non unicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.256.1.23 | Columnpm1001lhperfdatacomclientCurrent15StatInNonunicastCountPortn | read-only | current | Client Current 15-min Input Non Unicast counter :This OID gives the current 15-min Non Unicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.256.1.26 | Columnpm1001lhperfdatacomclientCurrent15StatOutBytesCountInvPortn | read-only | current | Client Current 15-min Output Bytes counter inv. :This OID indicates that the current 15-min Bytes counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.256.1.27 | Columnpm1001lhperfdatacomclientCurrent15StatOutBytesCountPortn | read-only | current | Client Current 15-min Output Bytes counter :This OID gives the current 15-min Bytes counter value |
| 1.3.6.1.4.1.20044.10.12.2.256.1.32 | Columnpm1001lhperfdatacomclientCurrent15StatOutBroadcastCountInvPortn | read-only | current | Client Current 15-min Output Broadcast counter inv. :This OID indicates that the current 15-min Broadcast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.256.1.33 | Columnpm1001lhperfdatacomclientCurrent15StatOutBroadcastCountPortn | read-only | current | Client Current 15-min Output Broadcast counter :This OID gives the current 15-min Broadcast counter value |
| 1.3.6.1.4.1.20044.10.12.2.256.1.34 | Columnpm1001lhperfdatacomclientCurrent15StatOutMulticastCountInvPortn | read-only | current | Client Current 15-min Output Multicast counter inv. :This OID indicates that the current 15-min Multicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.256.1.35 | Columnpm1001lhperfdatacomclientCurrent15StatOutMulticastCountPortn | read-only | current | Client Current 15-min Output Multicast counter :This OID gives the current 15-min Multicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.256.1.42 | Columnpm1001lhperfdatacomclientCurrent15StatOutUnicastCountInvPortn | read-only | current | Client Current 15-min Output Unicast counter inv. :This OID indicates that the current 15-min Unicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.256.1.43 | Columnpm1001lhperfdatacomclientCurrent15StatOutUnicastCountPortn | read-only | current | Client Current 15-min Output Unicast counter :This OID gives the current 15-min Unicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.256.1.44 | Columnpm1001lhperfdatacomclientCurrent15StatOutNonunicastCountInvPortn | read-only | current | Client Current 15-min Output Non Unicast counter inv. :This OID indicates that the current 15-min Non Unicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.256.1.45 | Columnpm1001lhperfdatacomclientCurrent15StatOutNonunicastCountPortn | read-only | current | Client Current 15-min Output Non Unicast counter :This OID gives the current 15-min Non Unicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.264 | Tablepm1001lhPerfDatacomClientPast15StatHistoryPort1Table | not-accessible | current | List of pm1001lhPerfDatacomClientPast15StatHistory Article |
| 1.3.6.1.4.1.20044.10.12.2.264.1 | Rowpm1001lhPerfDatacomClientPast15StatHistoryPort1Entry | not-accessible | current | Row definition for the pm1001lhPerfDatacomClientPast15StatHistory table |
| 1.3.6.1.4.1.20044.10.12.2.264.1.1 | Columnpm1001lhPerfDatacomClientPast15StatHistoryPort1Index | read-only | current | Index definition for the pm1001lhPerfDatacomClientPast15StatHistory table |
| 1.3.6.1.4.1.20044.10.12.2.264.1.2 | Columnpm1001lhperfdatacomclientPast15StatInBytesCountInvPort1 | read-only | current | Client Past 15-min Input Bytes counter inv. :This OID indicates that the past 15-min Bytes counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.264.1.3 | Columnpm1001lhperfdatacomclientPast15StatInBytesCountPort1 | read-only | current | Client Past 15-min Input Bytes counter :This OID gives the past 15-min Bytes counter value |
| 1.3.6.1.4.1.20044.10.12.2.264.1.4 | Columnpm1001lhperfdatacomclientPast15StatInCrcCountInvPort1 | read-only | current | Client Past 15-min Input CRC counter inv. :This OID indicates that the past 15-min CRC counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.264.1.5 | Columnpm1001lhperfdatacomclientPast15StatInCrcCountPort1 | read-only | current | Client Past 15-min Input CRC counter :This OID gives the past 15-min CRC counter value |
| 1.3.6.1.4.1.20044.10.12.2.264.1.8 | Columnpm1001lhperfdatacomclientPast15StatInBroadcastCountInvPort1 | read-only | current | Client Past 15-min Input Broadcast counter inv. :This OID indicates that the past 15-min Broadcast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.264.1.9 | Columnpm1001lhperfdatacomclientPast15StatInBroadcastCountPort1 | read-only | current | Client Past 15-min Input Broadcast counter :This OID gives the past 15-min Broadcast counter value |
| 1.3.6.1.4.1.20044.10.12.2.264.1.10 | Columnpm1001lhperfdatacomclientPast15StatInMulticastCountInvPort1 | read-only | current | Client Past 15-min Input Multicast counter inv. :This OID indicates that the past 15-min Multicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.264.1.11 | Columnpm1001lhperfdatacomclientPast15StatInMulticastCountPort1 | read-only | current | Client Past 15-min Input Multicast counter :This OID gives the past 15-min Multicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.264.1.20 | Columnpm1001lhperfdatacomclientPast15StatInUnicastCountInvPort1 | read-only | current | Client Past 15-min Input Unicast counter inv. :This OID indicates that the past 15-min Unicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.264.1.21 | Columnpm1001lhperfdatacomclientPast15StatInUnicastCountPort1 | read-only | current | Client Past 15-min Input Unicast counter :This OID gives the past 15-min Unicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.264.1.22 | Columnpm1001lhperfdatacomclientPast15StatInNonunicastCountInvPort1 | read-only | current | Client Past 15-min Input Non Unicast counter inv. :This OID indicates that the past 15-min Non unicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.264.1.23 | Columnpm1001lhperfdatacomclientPast15StatInNonunicastCountPort1 | read-only | current | Client Past 15-min Input Non Unicast counter :This OID gives the past 15-min Non Unicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.264.1.26 | Columnpm1001lhperfdatacomclientPast15StatOutBytesCountInvPort1 | read-only | current | Client Past 15-min Output Bytes counter inv. :This OID indicates that the past 15-min Bytes counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.264.1.27 | Columnpm1001lhperfdatacomclientPast15StatOutBytesCountPort1 | read-only | current | Client Past 15-min Output Bytes counter :This OID gives the past 15-min Bytes counter value |
| 1.3.6.1.4.1.20044.10.12.2.264.1.32 | Columnpm1001lhperfdatacomclientPast15StatOutBroadcastCountInvPort1 | read-only | current | Client Past 15-min Output Broadcast counter inv. :This OID indicates that the past 15-min Broadcast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.264.1.33 | Columnpm1001lhperfdatacomclientPast15StatOutBroadcastCountPort1 | read-only | current | Client Past 15-min Output Broadcast counter :This OID gives the past 15-min Broadcast counter value |
| 1.3.6.1.4.1.20044.10.12.2.264.1.34 | Columnpm1001lhperfdatacomclientPast15StatOutMulticastCountInvPort1 | read-only | current | Client Past 15-min Output Multicast counter inv. :This OID indicates that the past 15-min Multicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.264.1.35 | Columnpm1001lhperfdatacomclientPast15StatOutMulticastCountPort1 | read-only | current | Client Past 15-min Output Multicast counter :This OID gives the past 15-min Multicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.264.1.42 | Columnpm1001lhperfdatacomclientPast15StatOutUnicastCountInvPort1 | read-only | current | Client Past 15-min Output Unicast counter inv. :This OID indicates that the past 15-min Unicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.264.1.43 | Columnpm1001lhperfdatacomclientPast15StatOutUnicastCountPort1 | read-only | current | Client Past 15-min Output Unicast counter :This OID gives the past 15-min Unicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.264.1.44 | Columnpm1001lhperfdatacomclientPast15StatOutNonunicastCountInvPort1 | read-only | current | Client Past 15-min Output Non Unicast counter inv. :This OID indicates that the past 15-min Non Unicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.264.1.45 | Columnpm1001lhperfdatacomclientPast15StatOutNonunicastCountPort1 | read-only | current | Client Past 15-min Output Non Unicast counter :This OID gives the past 15-min Non Unicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.272 | Tablepm1001lhPerfDatacomClientCurrent24StatTable | not-accessible | current | List of pm1001lhPerfDatacomClientCurrent24Stat Article |
| 1.3.6.1.4.1.20044.10.12.2.272.1 | Rowpm1001lhPerfDatacomClientCurrent24StatEntry | not-accessible | current | Row definition for the pm1001lhPerfDatacomClientCurrent24Stat table |
| 1.3.6.1.4.1.20044.10.12.2.272.1.1 | Columnpm1001lhPerfDatacomClientCurrent24StatIndex | read-only | current | Index definition for the pm1001lhPerfDatacomClientCurrent24Stat table |
| 1.3.6.1.4.1.20044.10.12.2.272.1.2 | Columnpm1001lhperfdatacomclientCurrent24StatInBytesCountInvPortn | read-only | current | Client Current 24-hours Input Bytes counter inv. :This OID indicates that the current 24-hours Bytes counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.272.1.3 | Columnpm1001lhperfdatacomclientCurrent24StatInBytesCountPortn | read-only | current | Client Current 24-hours Input Bytes counter :This OID gives the current 24-hours Bytes counter value |
| 1.3.6.1.4.1.20044.10.12.2.272.1.4 | Columnpm1001lhperfdatacomclientCurrent24StatInCrcCountInvPortn | read-only | current | Client Current 24-hours Input CRC counter inv. :This OID indicates that the current 24-hours CRC counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.272.1.5 | Columnpm1001lhperfdatacomclientCurrent24StatInCrcCountPortn | read-only | current | Client Current 24-hours Input CRC counter :This OID gives the current 24-hours CRC counter value |
| 1.3.6.1.4.1.20044.10.12.2.272.1.8 | Columnpm1001lhperfdatacomclientCurrent24StatInBroadcastCountInvPortn | read-only | current | Client Current 24-hours Input Broadcast counter inv. :This OID indicates that the current 24-hours Broadcast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.272.1.9 | Columnpm1001lhperfdatacomclientCurrent24StatInBroadcastCountPortn | read-only | current | Client Current 24-hours Input Broadcast counter :This OID gives the current 24-hours Broadcast counter value |
| 1.3.6.1.4.1.20044.10.12.2.272.1.10 | Columnpm1001lhperfdatacomclientCurrent24StatInMulticastCountInvPortn | read-only | current | Client Current 24-hours Input Multicast counter inv. :This OID indicates that the current 24-hours Multicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.272.1.11 | Columnpm1001lhperfdatacomclientCurrent24StatInMulticastCountPortn | read-only | current | Client Current 24-hours Input Multicast counter :This OID gives the current 24-hours Multicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.272.1.20 | Columnpm1001lhperfdatacomclientCurrent24StatInUnicastCountInvPortn | read-only | current | Client Current 24-hours Input Unicast counter inv. :This OID indicates that the current 24-hours Unicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.272.1.21 | Columnpm1001lhperfdatacomclientCurrent24StatInUnicastCountPortn | read-only | current | Client Current 24-hours Input Unicast counter :This OID gives the current 24-hours Unicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.272.1.22 | Columnpm1001lhperfdatacomclientCurrent24StatInNonunicastCountInvPortn | read-only | current | Client Current 24-hours Input Non Unicast counter inv. :This OID indicates that the current 24-hours Non unicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.272.1.23 | Columnpm1001lhperfdatacomclientCurrent24StatInNonunicastCountPortn | read-only | current | Client Current 24-hours Input Non Unicast counter :This OID gives the current 24-hours Non Unicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.272.1.26 | Columnpm1001lhperfdatacomclientCurrent24StatOutBytesCountInvPortn | read-only | current | Client Current 24-hours Output Bytes counter inv. :This OID indicates that the current 24-hours Bytes counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.272.1.27 | Columnpm1001lhperfdatacomclientCurrent24StatOutBytesCountPortn | read-only | current | Client Current 24-hours Output Bytes counter :This OID gives the current 24-hours Bytes counter value |
| 1.3.6.1.4.1.20044.10.12.2.272.1.32 | Columnpm1001lhperfdatacomclientCurrent24StatOutBroadcastCountInvPortn | read-only | current | Client Current 24-hours Output Broadcast counter inv. :This OID indicates that the current 24-hours Broadcast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.272.1.33 | Columnpm1001lhperfdatacomclientCurrent24StatOutBroadcastCountPortn | read-only | current | Client Current 24-hours Output Broadcast counter :This OID gives the current 24-hours Broadcast counter value |
| 1.3.6.1.4.1.20044.10.12.2.272.1.34 | Columnpm1001lhperfdatacomclientCurrent24StatOutMulticastCountInvPortn | read-only | current | Client Current 24-hours Output Multicast counter inv. :This OID indicates that the current 24-hours Multicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.272.1.35 | Columnpm1001lhperfdatacomclientCurrent24StatOutMulticastCountPortn | read-only | current | Client Current 24-hours Output Multicast counter :This OID gives the current 24-hours Multicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.272.1.42 | Columnpm1001lhperfdatacomclientCurrent24StatOutUnicastCountInvPortn | read-only | current | Client Current 24-hours Output Unicast counter inv. :This OID indicates that the current 24-hours Unicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.272.1.43 | Columnpm1001lhperfdatacomclientCurrent24StatOutUnicastCountPortn | read-only | current | Client Current 24-hours Output Unicast counter :This OID gives the current 24-hours Unicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.272.1.44 | Columnpm1001lhperfdatacomclientCurrent24StatOutNonunicastCountInvPortn | read-only | current | Client Current 24-hours Output Non Unicast counter inv. :This OID indicates that the current 24-hours Non Unicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.272.1.45 | Columnpm1001lhperfdatacomclientCurrent24StatOutNonunicastCountPortn | read-only | current | Client Current 24-hours Output Non Unicast counter :This OID gives the current 24-hours Non Unicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.280 | Tablepm1001lhPerfDatacomClientPast24StatHistoryPort1Table | not-accessible | current | List of pm1001lhPerfDatacomClientPast24StatHistory Article |
| 1.3.6.1.4.1.20044.10.12.2.280.1 | Rowpm1001lhPerfDatacomClientPast24StatHistoryPort1Entry | not-accessible | current | Row definition for the pm1001lhPerfDatacomClientPast24StatHistory table |
| 1.3.6.1.4.1.20044.10.12.2.280.1.1 | Columnpm1001lhPerfDatacomClientPast24StatHistoryPort1Index | read-only | current | Index definition for the pm1001lhPerfDatacomClientPast24StatHistory table |
| 1.3.6.1.4.1.20044.10.12.2.280.1.2 | Columnpm1001lhperfdatacomclientPast24StatInBytesCountInvPort1 | read-only | current | Client Past 24-hours Input Bytes counter inv. :This OID indicates that the past 24-hours Bytes counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.280.1.3 | Columnpm1001lhperfdatacomclientPast24StatInBytesCountPort1 | read-only | current | Client Past 24-hours Input Bytes counter :This OID gives the past 24-hours Bytes counter value |
| 1.3.6.1.4.1.20044.10.12.2.280.1.4 | Columnpm1001lhperfdatacomclientPast24StatInCrcCountInvPort1 | read-only | current | Client Past 24-hours Input CRC counter inv. :This OID indicates that the past 24-hours CRC counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.280.1.5 | Columnpm1001lhperfdatacomclientPast24StatInCrcCountPort1 | read-only | current | Client Past 24-hours Input CRC counter :This OID gives the past 24-hours CRC counter value |
| 1.3.6.1.4.1.20044.10.12.2.280.1.8 | Columnpm1001lhperfdatacomclientPast24StatInBroadcastCountInvPort1 | read-only | current | Client Past 24-hours Input Broadcast counter inv. :This OID indicates that the past 24-hours Broadcast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.280.1.9 | Columnpm1001lhperfdatacomclientPast24StatInBroadcastCountPort1 | read-only | current | Client Past 24-hours Input Broadcast counter :This OID gives the past 24-hours Broadcast counter value |
| 1.3.6.1.4.1.20044.10.12.2.280.1.10 | Columnpm1001lhperfdatacomclientPast24StatInMulticastCountInvPort1 | read-only | current | Client Past 24-hours Input Multicast counter inv. :This OID indicates that the past 24-hours Multicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.280.1.11 | Columnpm1001lhperfdatacomclientPast24StatInMulticastCountPort1 | read-only | current | Client Past 24-hours Input Multicast counter :This OID gives the past 24-hours Multicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.280.1.20 | Columnpm1001lhperfdatacomclientPast24StatInUnicastCountInvPort1 | read-only | current | Client Past 24-hours Input Unicast counter inv. :This OID indicates that the past 24-hours Unicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.280.1.21 | Columnpm1001lhperfdatacomclientPast24StatInUnicastCountPort1 | read-only | current | Client Past 24-hours Input Unicast counter :This OID gives the past 24-hours Unicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.280.1.22 | Columnpm1001lhperfdatacomclientPast24StatInNonunicastCountInvPort1 | read-only | current | Client Past 24-hours Input Non Unicast counter inv. :This OID indicates that the past 24-hours Non unicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.280.1.23 | Columnpm1001lhperfdatacomclientPast24StatInNonunicastCountPort1 | read-only | current | Client Past 24-hours Input Non Unicast counter :This OID gives the past 24-hours Non Unicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.280.1.26 | Columnpm1001lhperfdatacomclientPast24StatOutBytesCountInvPort1 | read-only | current | Client Past 24-hours Output Bytes counter inv. :This OID indicates that the past 24-hours Bytes counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.280.1.27 | Columnpm1001lhperfdatacomclientPast24StatOutBytesCountPort1 | read-only | current | Client Past 24-hours Output Bytes counter :This OID gives the past 24-hours Bytes counter value |
| 1.3.6.1.4.1.20044.10.12.2.280.1.32 | Columnpm1001lhperfdatacomclientPast24StatOutBroadcastCountInvPort1 | read-only | current | Client Past 24-hours Output Broadcast counter inv. :This OID indicates that the past 24-hours Broadcast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.280.1.33 | Columnpm1001lhperfdatacomclientPast24StatOutBroadcastCountPort1 | read-only | current | Client Past 24-hours Output Broadcast counter :This OID gives the past 24-hours Broadcast counter value |
| 1.3.6.1.4.1.20044.10.12.2.280.1.34 | Columnpm1001lhperfdatacomclientPast24StatOutMulticastCountInvPort1 | read-only | current | Client Past 24-hours Output Multicast counter inv. :This OID indicates that the past 24-hours Multicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.280.1.35 | Columnpm1001lhperfdatacomclientPast24StatOutMulticastCountPort1 | read-only | current | Client Past 24-hours Output Multicast counter :This OID gives the past 24-hours Multicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.280.1.42 | Columnpm1001lhperfdatacomclientPast24StatOutUnicastCountInvPort1 | read-only | current | Client Past 24-hours Output Unicast counter inv. :This OID indicates that the past 24-hours Unicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.280.1.43 | Columnpm1001lhperfdatacomclientPast24StatOutUnicastCountPort1 | read-only | current | Client Past 24-hours Output Unicast counter :This OID gives the past 24-hours Unicast counter value |
| 1.3.6.1.4.1.20044.10.12.2.280.1.44 | Columnpm1001lhperfdatacomclientPast24StatOutNonunicastCountInvPort1 | read-only | current | Client Past 24-hours Output Non Unicast counter inv. :This OID indicates that the past 24-hours Non Unicast counter is invalid |
| 1.3.6.1.4.1.20044.10.12.2.280.1.45 | Columnpm1001lhperfdatacomclientPast24StatOutNonunicastCountPort1 | read-only | current | Client Past 24-hours Output Non Unicast counter :This OID gives the past 24-hours Non Unicast counter value |
| 1.3.6.1.4.1.20044.10.12.3 | Nodepm1001lhMonLine | |||
| 1.3.6.1.4.1.20044.10.12.3.128 | Tablepm1001lhPerfTelecomLineCurrent15StatTable | not-accessible | current | List of pm1001lhPerfTelecomLineCurrent15Stat Article |
| 1.3.6.1.4.1.20044.10.12.3.128.1 | Rowpm1001lhPerfTelecomLineCurrent15StatEntry | not-accessible | current | Row definition for the pm1001lhPerfTelecomLineCurrent15Stat table |
| 1.3.6.1.4.1.20044.10.12.3.128.1.1 | Columnpm1001lhPerfTelecomLineCurrent15StatIndex | read-only | current | Index definition for the pm1001lhPerfTelecomLineCurrent15Stat table |
| 1.3.6.1.4.1.20044.10.12.3.128.1.2 | Columnpm1001lhPerfTelecomLineCurrent15StatInvCvPortn | read-only | current | Current 15-min CV counter inv. :This OID indicates that the current 15-min Coding Violation counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.128.1.3 | Columnpm1001lhPerfTelecomLineCurrent15StatCvValuePortn | read-only | current | Current 15-min CV counter :This OID gives the current 15-min Coding Violation counter value |
| 1.3.6.1.4.1.20044.10.12.3.128.1.4 | Columnpm1001lhPerfTelecomLineCurrent15StatInvEsPortn | read-only | current | Current 15-min ES counter inv. :This OID indicates that the current 15-min Errored Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.128.1.5 | Columnpm1001lhPerfTelecomLineCurrent15StatEsValuePortn | read-only | current | Current 15-min ES counter :This OID gives the current 15-min Errored Second counter value |
| 1.3.6.1.4.1.20044.10.12.3.128.1.6 | Columnpm1001lhPerfTelecomLineCurrent15StatInvSesPortn | read-only | current | Current 15-min SES counter inv. :This OID indicates that the current 15-min severely Errored Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.128.1.7 | Columnpm1001lhPerfTelecomLineCurrent15StatSesValuePortn | read-only | current | Current 15-min SES counter :This OID gives the current 15-min severely Errored Second counter value |
| 1.3.6.1.4.1.20044.10.12.3.128.1.8 | Columnpm1001lhPerfTelecomLineCurrent15StatInvSefsPortn | read-only | current | Current 15-min SEFS counter inv. :This OID indicates that the current 15-min severely Errored Framing Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.128.1.9 | Columnpm1001lhPerfTelecomLineCurrent15StatSefsValuePortn | read-only | current | Current 15-min SEFS counter :This OID gives the current 15-min severely Errored Framing Second counter value |
| 1.3.6.1.4.1.20044.10.12.3.128.1.10 | Columnpm1001lhPerfTelecomLineCurrent15StatInvUasPortn | read-only | current | Current 15-min UAS counter inv. :This OID indicates that the current 15-min UnAvailable Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.128.1.11 | Columnpm1001lhPerfTelecomLineCurrent15StatUasValuePortn | read-only | current | Current 15-min UAS counter :This OID gives the current 15-min UnAvailable Second counter value |
| 1.3.6.1.4.1.20044.10.12.3.129 | Tablepm1001lhPerfTelecomLinePast15StatHistoryPort1Table | not-accessible | current | List of pm1001lhPerfTelecomLinePast15StatHistory Article |
| 1.3.6.1.4.1.20044.10.12.3.129.1 | Rowpm1001lhPerfTelecomLinePast15StatHistoryPort1Entry | not-accessible | current | Row definition for the pm1001lhPerfTelecomLinePast15StatHistory table |
| 1.3.6.1.4.1.20044.10.12.3.129.1.1 | Columnpm1001lhPerfTelecomLinePast15StatHistoryPort1Index | read-only | current | Index definition for the pm1001lhPerfTelecomLinePast15StatHistory table |
| 1.3.6.1.4.1.20044.10.12.3.129.1.2 | Columnpm1001lhPerfTelecomLinePast15StatHistoryInvCvPort1 | read-only | current | Previous 15-min CV counter inv. :This OID indicates that the previous 15-min Coding Violation counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.129.1.3 | Columnpm1001lhPerfTelecomLinePast15StatHistoryCvValuePort1 | read-only | current | Previous 15-min CV counter :This OID gives the previous 15-min Coding Violation counter value |
| 1.3.6.1.4.1.20044.10.12.3.129.1.4 | Columnpm1001lhPerfTelecomLinePast15StatHistoryInvEsPort1 | read-only | current | Previous 15-min ES counter inv. :This OID indicates that the previous 15-min Errored Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.129.1.5 | Columnpm1001lhPerfTelecomLinePast15StatHistoryEsValuePort1 | read-only | current | Previous 15-min ES counter :This OID gives the previous 15-min Errored Second counter value |
| 1.3.6.1.4.1.20044.10.12.3.129.1.6 | Columnpm1001lhPerfTelecomLinePast15StatHistoryInvSesPort1 | read-only | current | Previous 15-min SES counter inv. :This OID indicates that the previous 15-min severely Errored Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.129.1.7 | Columnpm1001lhPerfTelecomLinePast15StatHistorySesValuePort1 | read-only | current | Previous 15-min SES counter :This OID gives the previous 15-min severely Errored Second counter value |
| 1.3.6.1.4.1.20044.10.12.3.129.1.8 | Columnpm1001lhPerfTelecomLinePast15StatHistoryInvSefsPort1 | read-only | current | Previous 15-min SEFS counter inv. :This OID indicates that the previous 15-min severely Errored Framing Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.129.1.9 | Columnpm1001lhPerfTelecomLinePast15StatHistorySefsValuePort1 | read-only | current | Previous 15-min SEFS counter :This OID gives the previous 15-min severely Errored Framing Second counter value |
| 1.3.6.1.4.1.20044.10.12.3.129.1.10 | Columnpm1001lhPerfTelecomLinePast15StatHistoryInvUasPort1 | read-only | current | Previous 15-min UAS counter inv. :This OID indicates that the previous 15-min UnAvailable Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.129.1.11 | Columnpm1001lhPerfTelecomLinePast15StatHistoryUasValuePort1 | read-only | current | Previous 15-min UAS counter :This OID gives the previous 15-min UnAvailable Second counter value |
| 1.3.6.1.4.1.20044.10.12.3.130 | Tablepm1001lhPerfTelecomLineCurrent24StatTable | not-accessible | current | List of pm1001lhPerfTelecomLineCurrent24Stat Article |
| 1.3.6.1.4.1.20044.10.12.3.130.1 | Rowpm1001lhPerfTelecomLineCurrent24StatEntry | not-accessible | current | Row definition for the pm1001lhPerfTelecomLineCurrent24Stat table |
| 1.3.6.1.4.1.20044.10.12.3.130.1.1 | Columnpm1001lhPerfTelecomLineCurrent24StatIndex | read-only | current | Index definition for the pm1001lhPerfTelecomLineCurrent24Stat table |
| 1.3.6.1.4.1.20044.10.12.3.130.1.2 | Columnpm1001lhPerfTelecomLineCurrent24StatInvCvPortn | read-only | current | Current 24-hours CV counter inv. :This OID indicates that the current 24-hours Coding Violation counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.130.1.3 | Columnpm1001lhPerfTelecomLineCurrent24StatCvValuePortn | read-only | current | Current 24-hours CV counter :This OID gives the current 24-hours Coding Violation counter value |
| 1.3.6.1.4.1.20044.10.12.3.130.1.4 | Columnpm1001lhPerfTelecomLineCurrent24StatInvEsPortn | read-only | current | Current 24-hours ES counter inv. :This OID indicates that the current 24-hours Errored Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.130.1.5 | Columnpm1001lhPerfTelecomLineCurrent24StatEsValuePortn | read-only | current | Current 24-hours ES counter :This OID gives the current 24-hours Errored Second counter value |
| 1.3.6.1.4.1.20044.10.12.3.130.1.6 | Columnpm1001lhPerfTelecomLineCurrent24StatInvSesPortn | read-only | current | Current 24-hours SES counter inv. :This OID indicates that the current 24-hours severely Errored Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.130.1.7 | Columnpm1001lhPerfTelecomLineCurrent24StatSesValuePortn | read-only | current | Current 24-hours SES counter :This OID gives the current 24-hours severely Errored Second counter value |
| 1.3.6.1.4.1.20044.10.12.3.130.1.8 | Columnpm1001lhPerfTelecomLineCurrent24StatInvSefsPortn | read-only | current | Current 24-hours SEFS counter inv. :This OID indicates that the current 24-hours severely Errored Framing Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.130.1.9 | Columnpm1001lhPerfTelecomLineCurrent24StatSefsValuePortn | read-only | current | Current 24-hours SEFS counter :This OID gives the current 24-hours severely Errored Framing Second counter value |
| 1.3.6.1.4.1.20044.10.12.3.130.1.10 | Columnpm1001lhPerfTelecomLineCurrent24StatInvUasPortn | read-only | current | Current 24-hours UAS counter inv. :This OID indicates that the current 24-hours UnAvailable Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.130.1.11 | Columnpm1001lhPerfTelecomLineCurrent24StatUasValuePortn | read-only | current | Current 24-hours UAS counter :This OID gives the current 24-hours UnAvailable Second counter value |
| 1.3.6.1.4.1.20044.10.12.3.131 | Tablepm1001lhPerfTelecomLinePast24StatHistoryPort1Table | not-accessible | current | List of pm1001lhPerfTelecomLinePast24StatHistory Article |
| 1.3.6.1.4.1.20044.10.12.3.131.1 | Rowpm1001lhPerfTelecomLinePast24StatHistoryPort1Entry | not-accessible | current | Row definition for the pm1001lhPerfTelecomLinePast24StatHistory table |
| 1.3.6.1.4.1.20044.10.12.3.131.1.1 | Columnpm1001lhPerfTelecomLinePast24StatHistoryPort1Index | read-only | current | Index definition for the pm1001lhPerfTelecomLinePast24StatHistory table |
| 1.3.6.1.4.1.20044.10.12.3.131.1.2 | Columnpm1001lhPerfTelecomLinePast24StatHistoryInvCvPort1 | read-only | current | Previous 24-hours CV counter inv. :This OID indicates that the previous 24-hours Coding Violation counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.131.1.3 | Columnpm1001lhPerfTelecomLinePast24StatHistoryCvValuePort1 | read-only | current | Previous 24-hours CV counter :This OID gives the previous 24-hours Coding Violation counter value |
| 1.3.6.1.4.1.20044.10.12.3.131.1.4 | Columnpm1001lhPerfTelecomLinePast24StatHistoryInvEsPort1 | read-only | current | Previous 24-hours ES counter inv. :This OID indicates that the previous 24-hours Errored Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.131.1.5 | Columnpm1001lhPerfTelecomLinePast24StatHistoryEsValuePort1 | read-only | current | Previous 24-hours ES counter :This OID gives the previous 24-hours Errored Second counter value |
| 1.3.6.1.4.1.20044.10.12.3.131.1.6 | Columnpm1001lhPerfTelecomLinePast24StatHistoryInvSesPort1 | read-only | current | Previous 24-hours SES counter inv. :This OID indicates that the previous 24-hours severely Errored Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.131.1.7 | Columnpm1001lhPerfTelecomLinePast24StatHistorySesValuePort1 | read-only | current | Previous 24-hours SES counter :This OID gives the previous 24-hours severely Errored Second counter value |
| 1.3.6.1.4.1.20044.10.12.3.131.1.8 | Columnpm1001lhPerfTelecomLinePast24StatHistoryInvSefsPort1 | read-only | current | Previous 24-hours SEFS counter inv. :This OID indicates that the previous 24-hours severely Errored Framing Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.131.1.9 | Columnpm1001lhPerfTelecomLinePast24StatHistorySefsValuePort1 | read-only | current | Previous 24-hours SEFS counter :This OID gives the previous 24-hours severely Errored Framing Second counter value |
| 1.3.6.1.4.1.20044.10.12.3.131.1.10 | Columnpm1001lhPerfTelecomLinePast24StatHistoryInvUasPort1 | read-only | current | Previous 24-hours UAS counter inv. :This OID indicates that the previous 24-hours UnAvailable Second counter is invalid |
| 1.3.6.1.4.1.20044.10.12.3.131.1.11 | Columnpm1001lhPerfTelecomLinePast24StatHistoryUasValuePort1 | read-only | current | Previous 24-hours UAS counter :This OID gives the previous 24-hours UnAvailable Second counter value |
| 1.3.6.1.4.1.20044.10.12.4 | Nodepm1001lhRmon | |||
| 1.3.6.1.4.1.20044.10.12.4.1 | Nodepm1001lhRmonClient | |||
| 1.3.6.1.4.1.20044.10.12.4.1.16 | Tablepm1001lhMonupRmonByteCntTable | not-accessible | current | List of pm1001lhMonupRmonByteCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.16.1 | Rowpm1001lhMonupRmonByteCntEntry | not-accessible | current | Row definition for the pm1001lhMonupRmonByteCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.16.1.1 | Columnpm1001lhMonupRmonByteCntIndex | read-only | current | Index definition for the pm1001lhMonupRmonByteCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.16.1.2 | Columnpm1001lhMonupRmonByteCntValuePortn | read-only | current | Client Input Bytes :This counter is increased each time a data byte is received on the client port <Help> This counter gives the number of bytes received on th… |
| 1.3.6.1.4.1.20044.10.12.4.1.16.1.3 | Columnpm1001lhMonupRmonByteCntErrorPortn | read-only | current | Input Bytes Counter Error :This OID when set indicates the input Bytes counter value is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.16.1.4 | Columnpm1001lhMonupRmonByteCntOverloadPortn | read-only | current | Input Bytes Counter Overload :This OID when set indicates an input Bytes counter overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.24 | Tablepm1001lhMonupRmonCrcErrorCntTable | not-accessible | current | List of pm1001lhMonupRmonCrcErrorCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.24.1 | Rowpm1001lhMonupRmonCrcErrorCntEntry | not-accessible | current | Row definition for the pm1001lhMonupRmonCrcErrorCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.24.1.1 | Columnpm1001lhMonupRmonCrcErrorCntIndex | read-only | current | Index definition for the pm1001lhMonupRmonCrcErrorCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.24.1.2 | Columnpm1001lhMonupRmonCrcErrorCntValuePortn | read-only | current | Client Input CRC Errors :This counter is increased each time a CRC error is detected on the client port. <Help> This counter gives the number of CRC Errors rec… |
| 1.3.6.1.4.1.20044.10.12.4.1.24.1.3 | Columnpm1001lhMonupRmonCrcErrorCntErrorPortn | read-only | current | Input CRC Errors Counter Error :This OID when set indicates the input CRC Errors counter value is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.24.1.4 | Columnpm1001lhMonupRmonCrcErrorCntOverloadPortn | read-only | current | Input CRC Errors Counter Overload :This OID when set indicates an input CRC Errors counter overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.32 | Tablepm1001lhMonupRmonPacketsCntTable | not-accessible | current | List of pm1001lhMonupRmonPacketsCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.32.1 | Rowpm1001lhMonupRmonPacketsCntEntry | not-accessible | current | Row definition for the pm1001lhMonupRmonPacketsCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.32.1.1 | Columnpm1001lhMonupRmonPacketsCntIndex | read-only | current | Index definition for the pm1001lhMonupRmonPacketsCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.32.1.2 | Columnpm1001lhMonupRmonPacketsCntValuePortn | read-only | current | Packets Counter On Client Input :This counter is increased each time a packet is received on the client port <Help> This counter gives the number of packets re… |
| 1.3.6.1.4.1.20044.10.12.4.1.32.1.3 | Columnpm1001lhMonupRmonPacketsCntErrorPortn | read-only | current | Input Packets Counter Error :This OID when set indicates the input Packets counter value is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.32.1.4 | Columnpm1001lhMonupRmonPacketsCntOverloadPortn | read-only | current | Input Packets Counter Overload :This OID when set indicates an input Packets counter overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.40 | Tablepm1001lhMonupRmonBroadcastCntTable | not-accessible | current | List of pm1001lhMonupRmonBroadcastCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.40.1 | Rowpm1001lhMonupRmonBroadcastCntEntry | not-accessible | current | Row definition for the pm1001lhMonupRmonBroadcastCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.40.1.1 | Columnpm1001lhMonupRmonBroadcastCntIndex | read-only | current | Index definition for the pm1001lhMonupRmonBroadcastCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.40.1.2 | Columnpm1001lhMonupRmonBroadcastCntValuePortn | read-only | current | Client Input Broadcast Packets :This counter is increased each time a broadcast packet is received on the client port. <Help> This counter gives the number of … |
| 1.3.6.1.4.1.20044.10.12.4.1.40.1.3 | Columnpm1001lhMonupRmonBroadcastCntErrorPortn | read-only | current | Input Broadcast Counter Error :This OID when set indicates the input Broadcast counter value is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.40.1.4 | Columnpm1001lhMonupRmonBroadcastCntOverloadPortn | read-only | current | Input Broadcast Counter Overload :This OID when set indicates an input Broadcast counter overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.48 | Tablepm1001lhMonupRmonMulticastCntTable | not-accessible | current | List of pm1001lhMonupRmonMulticastCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.48.1 | Rowpm1001lhMonupRmonMulticastCntEntry | not-accessible | current | Row definition for the pm1001lhMonupRmonMulticastCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.48.1.1 | Columnpm1001lhMonupRmonMulticastCntIndex | read-only | current | Index definition for the pm1001lhMonupRmonMulticastCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.48.1.2 | Columnpm1001lhMonupRmonMulticastCntValuePortn | read-only | current | Client Input Multicast Packets :This counter is increased each time a Multicast packet is received on the client port. <Help> This counter gives the number of … |
| 1.3.6.1.4.1.20044.10.12.4.1.48.1.3 | Columnpm1001lhMonupRmonMulticastCntErrorPortn | read-only | current | Input Multicast Counter Error :This OID when set indicates the input Multicast counter value is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.48.1.4 | Columnpm1001lhMonupRmonMulticastCntOverloadPortn | read-only | current | Input Multicast Counter Overload :This OID when set indicates an input Multicast counter overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.56 | Tablepm1001lhMonupRmonTimerCntTable | not-accessible | current | List of pm1001lhMonupRmonTimerCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.56.1 | Rowpm1001lhMonupRmonTimerCntEntry | not-accessible | current | Row definition for the pm1001lhMonupRmonTimerCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.56.1.1 | Columnpm1001lhMonupRmonTimerCntIndex | read-only | current | Index definition for the pm1001lhMonupRmonTimerCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.56.1.2 | Columnpm1001lhMonupRmonTimerCntValuePortn | read-only | current | RMON Timer On Client Input :This is the timing counter dedicated to the upstream RMON counters. It is incremented every 125 us. |
| 1.3.6.1.4.1.20044.10.12.4.1.56.1.3 | Columnpm1001lhMonupRmonTimerCntErrorPortn | read-only | current | Input RMON Timer Error :This OID when set indicates the input RMON timer is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.56.1.4 | Columnpm1001lhMonupRmonTimerCntOverloadPortn | read-only | current | Input RMON Timer Overload :This OID when set indicates an input RMON timer overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.64 | Tablepm1001lhMonupRmonPauseFrameCntTable | not-accessible | current | List of pm1001lhMonupRmonPauseFrameCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.64.1 | Rowpm1001lhMonupRmonPauseFrameCntEntry | not-accessible | current | Row definition for the pm1001lhMonupRmonPauseFrameCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.64.1.1 | Columnpm1001lhMonupRmonPauseFrameCntIndex | read-only | current | Index definition for the pm1001lhMonupRmonPauseFrameCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.64.1.2 | Columnpm1001lhMonupRmonPauseFrameCntValuePortn | read-only | current | Pause Counter On Client Input :This counter is increased each time a Pause frame is received on the client port |
| 1.3.6.1.4.1.20044.10.12.4.1.64.1.3 | Columnpm1001lhMonupRmonPauseFrameCntErrorPortn | read-only | current | Input Pause Counter Error :This OID when set indicates the input Pause counter value is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.64.1.4 | Columnpm1001lhMonupRmonPauseFrameCntOverloadPortn | read-only | current | Input Pause Counter Overload :This OID when set indicates an input Pause counter overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.72 | Tablepm1001lhMonupRmonDropFrameCntTable | not-accessible | current | List of pm1001lhMonupRmonDropFrameCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.72.1 | Rowpm1001lhMonupRmonDropFrameCntEntry | not-accessible | current | Row definition for the pm1001lhMonupRmonDropFrameCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.72.1.1 | Columnpm1001lhMonupRmonDropFrameCntIndex | read-only | current | Index definition for the pm1001lhMonupRmonDropFrameCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.72.1.2 | Columnpm1001lhMonupRmonDropFrameCntValuePortn | read-only | current | Drop Counter On Client Input :This counter is increased each time a Frame is dropped on the input client port |
| 1.3.6.1.4.1.20044.10.12.4.1.72.1.3 | Columnpm1001lhMonupRmonDropFrameCntErrorPortn | read-only | current | Input Drop Counter Error :This OID when set indicates the input Drop counter value is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.72.1.4 | Columnpm1001lhMonupRmonDropFrameCntOverloadPortn | read-only | current | Input Drop Counter Overload :This OID when set indicates an input Drop counter overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.80 | Tablepm1001lhMonupRmonBitsCntTable | not-accessible | current | List of pm1001lhMonupRmonBitsCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.80.1 | Rowpm1001lhMonupRmonBitsCntEntry | not-accessible | current | Row definition for the pm1001lhMonupRmonBitsCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.80.1.1 | Columnpm1001lhMonupRmonBitsCntIndex | read-only | current | Index definition for the pm1001lhMonupRmonBitsCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.80.1.2 | Columnpm1001lhMonupRmonBitsCntValuePortn | read-only | current | Bits Counter On Client Input :This counter is increased each time a bit is received on the input client port |
| 1.3.6.1.4.1.20044.10.12.4.1.80.1.3 | Columnpm1001lhMonupRmonBitsCntErrorPortn | read-only | current | Input Bits Counter Error :This OID when set indicates the input Bits counter value is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.80.1.4 | Columnpm1001lhMonupRmonBitsCntOverloadPortn | read-only | current | Input Bits Counter Overload :This OID when set indicates an input Bits counter overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.88 | Tablepm1001lhMonupRmonUnicastCntTable | not-accessible | current | List of pm1001lhMonupRmonUnicastCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.88.1 | Rowpm1001lhMonupRmonUnicastCntEntry | not-accessible | current | Row definition for the pm1001lhMonupRmonUnicastCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.88.1.1 | Columnpm1001lhMonupRmonUnicastCntIndex | read-only | current | Index definition for the pm1001lhMonupRmonUnicastCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.88.1.2 | Columnpm1001lhMonupRmonUnicastCntValuePortn | read-only | current | Client Input Unicast Packets :This counter is increased each time a Unicast packet is received on client input <Help> This counter gives the number of Unicast … |
| 1.3.6.1.4.1.20044.10.12.4.1.88.1.3 | Columnpm1001lhMonupRmonUnicastCntErrorPortn | read-only | current | Input Unicast Counter Error :This OID when set indicates the input Drop counter value is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.88.1.4 | Columnpm1001lhMonupRmonUnicastCntOverloadPortn | read-only | current | Input Unicast Counter Overload :This OID when set indicates an input Drop counter overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.96 | Tablepm1001lhMonupRmonNonUnicastCntTable | not-accessible | current | List of pm1001lhMonupRmonNonUnicastCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.96.1 | Rowpm1001lhMonupRmonNonUnicastCntEntry | not-accessible | current | Row definition for the pm1001lhMonupRmonNonUnicastCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.96.1.1 | Columnpm1001lhMonupRmonNonUnicastCntIndex | read-only | current | Index definition for the pm1001lhMonupRmonNonUnicastCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.96.1.2 | Columnpm1001lhMonupRmonNonUnicastCntValuePortn | read-only | current | Client Input Not Unicast Packets :This counter is increased each time a Non Unicast packet is received on client input <Help> This counter gives the number of … |
| 1.3.6.1.4.1.20044.10.12.4.1.96.1.3 | Columnpm1001lhMonupRmonNonUnicastCntErrorPortn | read-only | current | Input Non Unicast Counter Error :This OID when set indicates the input Bits counter value is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.96.1.4 | Columnpm1001lhMonupRmonNonUnicastCntOverloadPortn | read-only | current | Input Non Unicast Counter Overload :This OID when set indicates an input Bits counter overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.112 | Tablepm1001lhMondwRmonByteCntTable | not-accessible | current | List of pm1001lhMondwRmonByteCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.112.1 | Rowpm1001lhMondwRmonByteCntEntry | not-accessible | current | Row definition for the pm1001lhMondwRmonByteCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.112.1.1 | Columnpm1001lhMondwRmonByteCntIndex | read-only | current | Index definition for the pm1001lhMondwRmonByteCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.112.1.2 | Columnpm1001lhMondwRmonByteCntValuePortn | read-only | current | Client Output Bytes :This counter is increased each time a data byte is transmitted on the client port. <Help> This counter gives the number of bytes transmitt… |
| 1.3.6.1.4.1.20044.10.12.4.1.112.1.3 | Columnpm1001lhMondwRmonByteCntErrorPortn | read-only | current | Output Bytes Counter Error :This OID when set indicates the output Bytes counter value is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.112.1.4 | Columnpm1001lhMondwRmonByteCntOverloadPortn | read-only | current | Output Bytes Counter Overload :This OID when set indicates an output Bytes counter overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.120 | Tablepm1001lhMondwRmonCrcErrorCntTable | not-accessible | current | List of pm1001lhMondwRmonCrcErrorCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.120.1 | Rowpm1001lhMondwRmonCrcErrorCntEntry | not-accessible | current | Row definition for the pm1001lhMondwRmonCrcErrorCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.120.1.1 | Columnpm1001lhMondwRmonCrcErrorCntIndex | read-only | current | Index definition for the pm1001lhMondwRmonCrcErrorCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.120.1.2 | Columnpm1001lhMondwRmonCrcErrorCntValuePortn | read-only | current | CRC Errors Counter On Client Output :This counter is increased each time a CRC error is detected on the output client port <Help> This counter gives the number… |
| 1.3.6.1.4.1.20044.10.12.4.1.120.1.3 | Columnpm1001lhMondwRmonCrcErrorCntErrorPortn | read-only | current | Output CRC Errors Counter Error :This OID when set indicates the output CRC Errors counter value is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.120.1.4 | Columnpm1001lhMondwRmonCrcErrorCntOverloadPortn | read-only | current | Output CRC Errors Counter Overload :This OID when set indicates an output CRC Errors counter overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.128 | Tablepm1001lhMondwRmonPacketsCntTable | not-accessible | current | List of pm1001lhMondwRmonPacketsCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.128.1 | Rowpm1001lhMondwRmonPacketsCntEntry | not-accessible | current | Row definition for the pm1001lhMondwRmonPacketsCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.128.1.1 | Columnpm1001lhMondwRmonPacketsCntIndex | read-only | current | Index definition for the pm1001lhMondwRmonPacketsCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.128.1.2 | Columnpm1001lhMondwRmonPacketsCntValuePortn | read-only | current | Packets Counter On Client Output :This counter is increased each time a packet is transmitted on the client port. <Help> This counter gives the number of packe… |
| 1.3.6.1.4.1.20044.10.12.4.1.128.1.3 | Columnpm1001lhMondwRmonPacketsCntErrorPortn | read-only | current | Output Packets Counter Error :This OID when set indicates the output Packets counter value is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.128.1.4 | Columnpm1001lhMondwRmonPacketsCntOverloadPortn | read-only | current | Output Packets Counter Overload :This OID when set indicates an output Packets counter overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.136 | Tablepm1001lhMondwRmonBroadcastCntTable | not-accessible | current | List of pm1001lhMondwRmonBroadcastCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.136.1 | Rowpm1001lhMondwRmonBroadcastCntEntry | not-accessible | current | Row definition for the pm1001lhMondwRmonBroadcastCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.136.1.1 | Columnpm1001lhMondwRmonBroadcastCntIndex | read-only | current | Index definition for the pm1001lhMondwRmonBroadcastCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.136.1.2 | Columnpm1001lhMondwRmonBroadcastCntValuePortn | read-only | current | Client Output Broadcast Packets :This counter is increased each time a broadcast packet is transmitted on the client port. <Help> This counter gives the number… |
| 1.3.6.1.4.1.20044.10.12.4.1.136.1.3 | Columnpm1001lhMondwRmonBroadcastCntErrorPortn | read-only | current | Output Broadcast Counter Error :This OID when set indicates the output Broadcast counter value is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.136.1.4 | Columnpm1001lhMondwRmonBroadcastCntOverloadPortn | read-only | current | Output Broadcast Counter Overload :This OID when set indicates an output Broadcast counter overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.144 | Tablepm1001lhMondwRmonMulticastCntTable | not-accessible | current | List of pm1001lhMondwRmonMulticastCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.144.1 | Rowpm1001lhMondwRmonMulticastCntEntry | not-accessible | current | Row definition for the pm1001lhMondwRmonMulticastCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.144.1.1 | Columnpm1001lhMondwRmonMulticastCntIndex | read-only | current | Index definition for the pm1001lhMondwRmonMulticastCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.144.1.2 | Columnpm1001lhMondwRmonMulticastCntValuePortn | read-only | current | Client Output Multicast Packets :This counter is increased each time a Multicast packet is tra,smitted on the client port. <Help> This counter gives the number… |
| 1.3.6.1.4.1.20044.10.12.4.1.144.1.3 | Columnpm1001lhMondwRmonMulticastCntErrorPortn | read-only | current | Output Multicast Counter Error :This OID when set indicates the output Multicast counter value is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.144.1.4 | Columnpm1001lhMondwRmonMulticastCntOverloadPortn | read-only | current | Output Multicast Counter Overload :This OID when set indicates an output Multicast counter overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.152 | Tablepm1001lhMondwRmonPauseFrameCntTable | not-accessible | current | List of pm1001lhMondwRmonPauseFrameCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.152.1 | Rowpm1001lhMondwRmonPauseFrameCntEntry | not-accessible | current | Row definition for the pm1001lhMondwRmonPauseFrameCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.152.1.1 | Columnpm1001lhMondwRmonPauseFrameCntIndex | read-only | current | Index definition for the pm1001lhMondwRmonPauseFrameCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.152.1.2 | Columnpm1001lhMondwRmonPauseFrameCntValuePortn | read-only | current | Pause Counter On Client Output :This counter is increased each time a Pause frame is generated by the PM on the client port |
| 1.3.6.1.4.1.20044.10.12.4.1.152.1.3 | Columnpm1001lhMondwRmonPauseFrameCntErrorPortn | read-only | current | Output Pause Counter Error :This OID when set indicates the output Pause counter value is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.152.1.4 | Columnpm1001lhMondwRmonPauseFrameCntOverloadPortn | read-only | current | Output Pause Counter Overload :This OID when set indicates an output Pause counter overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.160 | Tablepm1001lhMondwRmonTimerCntTable | not-accessible | current | List of pm1001lhMondwRmonTimerCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.160.1 | Rowpm1001lhMondwRmonTimerCntEntry | not-accessible | current | Row definition for the pm1001lhMondwRmonTimerCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.160.1.1 | Columnpm1001lhMondwRmonTimerCntIndex | read-only | current | Index definition for the pm1001lhMondwRmonTimerCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.160.1.2 | Columnpm1001lhMondwRmonTimerCntValuePortn | read-only | current | RMON Timer On Client Output :This is the timing counter dedicated to the downstream RMON counters. It is incremented every 125 us. |
| 1.3.6.1.4.1.20044.10.12.4.1.160.1.3 | Columnpm1001lhMondwRmonTimerCntErrorPortn | read-only | current | Output RMON Timer Error :This OID when set indicates the output RMON timer is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.160.1.4 | Columnpm1001lhMondwRmonTimerCntOverloadPortn | read-only | current | Output RMON Timer Overload :This OID when set indicates an output RMON timer overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.168 | Tablepm1001lhMondwRmonBitsCntTable | not-accessible | current | List of pm1001lhMondwRmonBitsCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.168.1 | Rowpm1001lhMondwRmonBitsCntEntry | not-accessible | current | Row definition for the pm1001lhMondwRmonBitsCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.168.1.1 | Columnpm1001lhMondwRmonBitsCntIndex | read-only | current | Index definition for the pm1001lhMondwRmonBitsCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.168.1.2 | Columnpm1001lhMondwRmonBitsCntValuePortn | read-only | current | Bits Counter On Client Output :This counter is increased each time a bit is received on the Output client port |
| 1.3.6.1.4.1.20044.10.12.4.1.168.1.3 | Columnpm1001lhMondwRmonBitsCntErrorPortn | read-only | current | Output Bits Counter Error :This OID when set indicates the output Bits counter value is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.168.1.4 | Columnpm1001lhMondwRmonBitsCntOverloadPortn | read-only | current | Output Bits Counter Overload :This OID when set indicates an output Bits counter overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.176 | Tablepm1001lhMondwRmonUnicastCntTable | not-accessible | current | List of pm1001lhMondwRmonUnicastCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.176.1 | Rowpm1001lhMondwRmonUnicastCntEntry | not-accessible | current | Row definition for the pm1001lhMondwRmonUnicastCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.176.1.1 | Columnpm1001lhMondwRmonUnicastCntIndex | read-only | current | Index definition for the pm1001lhMondwRmonUnicastCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.176.1.2 | Columnpm1001lhMondwRmonUnicastCntValuePortn | read-only | current | Client Output Unicast Packets :This counter is increased each time a Unicast packet is transmitted on client port <Help> This counter gives the number of Unica… |
| 1.3.6.1.4.1.20044.10.12.4.1.176.1.3 | Columnpm1001lhMondwRmonUnicastCntErrorPortn | read-only | current | Output Unicast Counter Error :This OID when set indicates the output RMON timer is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.176.1.4 | Columnpm1001lhMondwRmonUnicastCntOverloadPortn | read-only | current | Output Unicast Counter Overload :This OID when set indicates an output RMON timer overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.184 | Tablepm1001lhMondwRmonNonUnicastCntTable | not-accessible | current | List of pm1001lhMondwRmonNonUnicastCnt Article |
| 1.3.6.1.4.1.20044.10.12.4.1.184.1 | Rowpm1001lhMondwRmonNonUnicastCntEntry | not-accessible | current | Row definition for the pm1001lhMondwRmonNonUnicastCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.184.1.1 | Columnpm1001lhMondwRmonNonUnicastCntIndex | read-only | current | Index definition for the pm1001lhMondwRmonNonUnicastCnt table |
| 1.3.6.1.4.1.20044.10.12.4.1.184.1.2 | Columnpm1001lhMondwRmonNonUnicastCntValuePortn | read-only | current | Client Output Not Unicast Packets :This counter is increased each time a Non Unicast packet is transmitted on client port <Help> This counter gives the number … |
| 1.3.6.1.4.1.20044.10.12.4.1.184.1.3 | Columnpm1001lhMondwRmonNonUnicastCntErrorPortn | read-only | current | Output Non Unicast Counter Error :This OID when set indicates the output Bits counter value is invalid on client port |
| 1.3.6.1.4.1.20044.10.12.4.1.184.1.4 | Columnpm1001lhMondwRmonNonUnicastCntOverloadPortn | read-only | current | Output Non Unicast Counter Overload :This OID when set indicates an output Bits counter overload on client port |
| 1.3.6.1.4.1.20044.10.12.4.2 | Nodepm1001lhRmonLine | |||
| 1.3.6.1.4.1.20044.10.12.4.3 | Nodepm1001lhRmonOther | |||
| 1.3.6.1.4.1.20044.10.12.4.3.359 | Scalarpm1001lhMonCountersReset | read-write | current | RMON Counters Reset:This OID resets and restarts all the RMON counters |
| 1.3.6.1.4.1.20044.10.12.4.3.360 | Scalarpm1001lhMonCountersStop | read-write | current | RMON Counters stop:This OID stops all the RMON counters |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| Pm1001lhAdjustValue | INTEGER { otxadjustvalue0(0), otxadjustvalue1(1), otxadjustvalue2(2), otxadjustvalue3(3), otxadjustvalue4(4), otxadjustvalue5(5), otxadjustvalue6(6), otxadjustvalue7(7), otxadjustvalue8(8), otxadjustvalue9(9), otxadjustvalue10(10) } | current | Different values in Adjust mode on OTX-TLH on client and line ports |
| Pm1001lhOtxChannel | INTEGER | current | Channel selection on OTX-TLH on client and line ports |
| Pm1001lhOtxGrid | INTEGER { otxgrid200(200), otxgrid100(100), otxgrid50(50) } | current | Different grids on OTX-TLH on client and line ports |
| Pm1001lhOtxMode | INTEGER { otx80mode(1), otx60mode(2), otxadjustmode(4) } | current | Different modes on OTX-TLH on client and line ports |