EKINOPS-Pm801RR-MIB
262 objects
MIB for the Ekinops Pm801RR hardware.
Imported Objects
| EKINOPS-MIB | EkiApiState EkiMeasureType EkiMode ekinops EkiOnOff EkiProtocol EkiState EkiSynchroMode |
| SNMPv2-SMI | Counter32 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.20044.48 | IdentitymodulePm801RR | MIB for the Ekinops Pm801RR hardware. | ||
| 1.3.6.1.4.1.20044.48.2 | Nodepm801rralarms | |||
| 1.3.6.1.4.1.20044.48.2.1 | Nodepm801rrAlmOther | |||
| 1.3.6.1.4.1.20044.48.2.1.1 | Nodepm801rrAlmOtherNurg | |||
| 1.3.6.1.4.1.20044.48.2.1.2 | Nodepm801rrAlmOtherUrg | |||
| 1.3.6.1.4.1.20044.48.2.1.3 | Nodepm801rrAlmOtherCrit | |||
| 1.3.6.1.4.1.20044.48.2.1.3.0 | Nodepm801rrAlmsynthAlm0 | |||
| 1.3.6.1.4.1.20044.48.2.1.3.0.9 | Scalarpm801rrAlmModuleGlobFailure | read-only | current | Module Failure :This OID is set on detection of a failure originating from the PM <Condtype> MODULE_GLOB_FAILURE <Probcause> equipmentMalfunction (16) <Alarmty… |
| 1.3.6.1.4.1.20044.48.2.1.3.0.15 | Scalarpm801rrAlmDefFuseA | read-only | current | Fuse A Fail :This OID indicates that the fuse of the power input A is in fail condition <Help> Status of the Fuse A <Condtype> DEF_FUSE_A <Probcause> powerProb… |
| 1.3.6.1.4.1.20044.48.2.1.3.0.16 | Scalarpm801rrAlmDefFuseB | read-only | current | Fuse B Fail :This OID indicates that the fuse of the power input B is in fail condition <Help> Status of the Fuse B <Condtype> DEF_FUSE_B <Probcause> powerProb… |
| 1.3.6.1.4.1.20044.48.2.2 | Nodepm801rrAlmClient | |||
| 1.3.6.1.4.1.20044.48.2.2.1 | Nodepm801rrAlmClientNurg | |||
| 1.3.6.1.4.1.20044.48.2.2.1.17 | Nodepm801rrAlmclientXfpWarnings | |||
| 1.3.6.1.4.1.20044.48.2.2.1.17.1 | Scalarpm801rrAlmClientTxPwrLowWng | read-only | current | Line 1 Optical Tx Power Low Warning :Warning indicating that the Line 1 XFP/OTX transmitter transmitter output power is lower than the threshold value written … |
| 1.3.6.1.4.1.20044.48.2.2.1.17.2 | Scalarpm801rrAlmClientTxPwrHighWng | read-only | current | Line 1 Optical Tx Power High Warning :Warning indicating that the Line 1 XFP/OTX transmitter transmitter output power is higher than the threshold value writte… |
| 1.3.6.1.4.1.20044.48.2.2.1.17.3 | Scalarpm801rrAlmClientTxBiasLowWng | read-only | current | Line 1 Transceiver Bias Low Warning :Warning indicating that the Line 1 XFP/OTX transmitter laser bias current is lower than the threshold value written in the… |
| 1.3.6.1.4.1.20044.48.2.2.1.17.4 | Scalarpm801rrAlmClientTxBiasHighWng | read-only | current | Line 1 Transceiver Bias High Warning :Warning indicating that the Line 1 XFP/OTX transmitter laser bias current is higher than the threshold value written in t… |
| 1.3.6.1.4.1.20044.48.2.2.1.17.7 | Scalarpm801rrAlmClientTempLowWng | read-only | current | Line 1 Transceiver Temp Low Warning :Warning indicating that the Line 1 XFP/OTX temperature is lower than the threshold value written in the Line 1 XFP/OTX EEP… |
| 1.3.6.1.4.1.20044.48.2.2.1.17.8 | Scalarpm801rrAlmClientTempHighWng | read-only | current | Line 1 Transceiver Temp High Warning :Warning indicating that the Line 1 XFP/OTX temperature is higher than the threshold value written in the Line 1 XFP/OTX E… |
| 1.3.6.1.4.1.20044.48.2.2.1.17.15 | Scalarpm801rrAlmClientRxPwrLowWng | read-only | current | Line 1 Optical Rx Power Low Warning :Warning indicating that the Line 1 XFP/OTX received optical power is lower than the threshold value written in the Line 1 … |
| 1.3.6.1.4.1.20044.48.2.2.1.17.16 | Scalarpm801rrAlmClientRxPwrHighWng | read-only | current | Line 1 Optical Rx Power High Warning :Warning indicating that the Line 1 XFP/OTX received optical power is higher than the threshold value written in the Line … |
| 1.3.6.1.4.1.20044.48.2.2.1.23 | Nodepm801rrAlmclientOtxTlhWarnings | |||
| 1.3.6.1.4.1.20044.48.2.2.1.23.5 | Scalarpm801rrAlmClientModulatorAgingHighWarning | read-only | current | Line 1 Modulator Aging High Warning :Warning indicating the Line 1 OTX TLH modulator aging is higher than the threshold written in the EEPROM <Condtype> CLIENT… |
| 1.3.6.1.4.1.20044.48.2.2.1.23.6 | Scalarpm801rrAlmClientAgingHighWarning | read-only | current | Line 1 OTX TLH Aging High Warning :Warning indicating the Line 1 OTX TLH aging is higher than the threshold written in the EEPROM <Condtype> CLIENT_AGING_HIGH_… |
| 1.3.6.1.4.1.20044.48.2.2.1.23.12 | Scalarpm801rrAlmClientFreqDevHighWarning | read-only | current | Line 1 Freq. Deviation High Warning :Warning indicating the Line 1 OTX TLH frequency deviation is higher than the threshold written in the EEPROM <Condtype> CL… |
| 1.3.6.1.4.1.20044.48.2.2.1.23.14 | Scalarpm801rrAlmClientLaserTempHighWarning | read-only | current | Line 1 Laser Temp. High Warning :Warning indicating the Line 1 OTX TLH laser temperature is higher than the threshold written in the EEPROM <Condtype> CLIENT_L… |
| 1.3.6.1.4.1.20044.48.2.2.2 | Nodepm801rrAlmClientUrg | |||
| 1.3.6.1.4.1.20044.48.2.2.2.16 | Nodepm801rrAlmclientXfpAlarm1 | |||
| 1.3.6.1.4.1.20044.48.2.2.2.16.1 | Scalarpm801rrAlmClientTxPwrLowAla | read-only | current | Line 1 Optical Tx Power Low :Alarm indicating that the Line 1 XFP/OTX transmitter transmitter output power is lower than the threshold value written in the Lin… |
| 1.3.6.1.4.1.20044.48.2.2.2.16.2 | Scalarpm801rrAlmClientTxPwrHighAla | read-only | current | Line 1 Optical Tx Power High :Alarm indicating that the Line 1 XFP/OTX transmitter transmitter output power is higher than the threshold value written in the L… |
| 1.3.6.1.4.1.20044.48.2.2.2.16.3 | Scalarpm801rrAlmClientTxBiasLowAla | read-only | current | Line 1 Transceiver Bias Low :Alarm indicating that the Line 1 XFP/OTX transmitter laser bias current is lower than the threshold value written in the Line 1 XF… |
| 1.3.6.1.4.1.20044.48.2.2.2.16.4 | Scalarpm801rrAlmClientTxBiasHighAla | read-only | current | Line 1 Transceiver Bias High :Alarm indicating that the Line 1 XFP/OTX transmitter laser bias current is higher than the threshold value written in the Line 1 … |
| 1.3.6.1.4.1.20044.48.2.2.2.16.7 | Scalarpm801rrAlmClientTempLowAla | read-only | current | Line 1 Transceiver Temp Low :Alarm indicating that the Line 1 XFP/OTX temperature is lower than the threshold value written in the Line 1 XFP/OTX EEPROM <Condt… |
| 1.3.6.1.4.1.20044.48.2.2.2.16.8 | Scalarpm801rrAlmClientTempHighAla | read-only | current | Line 1 Transceiver Temp High :Alarm indicating that the Line 1 XFP/OTX temperature is higher than the threshold value written in the Line 1 XFP/OTX EEPROM <Con… |
| 1.3.6.1.4.1.20044.48.2.2.2.16.15 | Scalarpm801rrAlmClientRxPwrLowAla | read-only | current | Line 1 Optical Rx Power Low :Alarm indicating that the Line 1 XFP/OTX received optical power is lower than the threshold value written in the Line 1 XFP/OTX EE… |
| 1.3.6.1.4.1.20044.48.2.2.2.16.16 | Scalarpm801rrAlmClientRxPwrHighAla | read-only | current | Line 1 Optical Rx Power High :Alarm indicating that the Line 1 XFP/OTX received optical power is higher than the threshold value written in the Line 1 XFP/OTX … |
| 1.3.6.1.4.1.20044.48.2.2.2.22 | Nodepm801rrAlmclientOtxTlhAlarms3 | |||
| 1.3.6.1.4.1.20044.48.2.2.2.22.5 | Scalarpm801rrAlmClientModulatorAgingHighAla | read-only | current | Line 1 Modulator Aging High Alarm :Alarm indicating the Line 1 OTX TLH modulator aging is higher than the threshold written in the EEPROM <Condtype> CLIENT_MOD… |
| 1.3.6.1.4.1.20044.48.2.2.2.22.6 | Scalarpm801rrAlmClientAgingHighAla | read-only | current | Line 1 OTX TLH Aging High Alarm :Alarm indicating the Line 1 OTX TLH aging is higher than the threshold written in the EEPROM <Condtype> CLIENT_AGING_HIGH_ALA … |
| 1.3.6.1.4.1.20044.48.2.2.2.22.9 | Scalarpm801rrAlmClientCdrNotReady | read-only | current | Line 1 CDR Not Ready :This OID indicates the Clock Data Recovery unit is not yet initialized <Help> This alarm indicates the Clock Data Recovery unit is not ye… |
| 1.3.6.1.4.1.20044.48.2.2.2.22.12 | Scalarpm801rrAlmClientFreqDevHighAla | read-only | current | Line 1 Freq. Deviation High Alarm :Alarm indicating the Line 1 OTX TLH frequency deviation is higher than the threshold written in the EEPROM <Condtype> CLIENT… |
| 1.3.6.1.4.1.20044.48.2.2.2.22.14 | Scalarpm801rrAlmClientLaserTempHighAla | read-only | current | Line 1 Laser Temp. High Alarm :Alarm indicating the Line 1 OTX TLH laser temperature is higher than the threshold written in the EEPROM <Condtype> CLIENT_LASER… |
| 1.3.6.1.4.1.20044.48.2.2.3 | Nodepm801rrAlmClientCrit | |||
| 1.3.6.1.4.1.20044.48.2.2.3.8 | Nodepm801rrAlmsynthAlm8 | |||
| 1.3.6.1.4.1.20044.48.2.2.3.8.1 | Scalarpm801rrAlmClientXfpAbsent | read-only | current | Line 1 Optical Module Absent :This OID indicates the Line 1 optical interface (XFP or OTX) is not present in the PM <Help> This alarm indicates if the line 1 t… |
| 1.3.6.1.4.1.20044.48.2.2.3.8.2 | Scalarpm801rrAlmClientInitNotCompl | read-only | current | Line 1 Optical Module Ready :This OID indicates the optical interface (XFP or OTX) is not operational <Help> This status indicates if the line 1 transceiver ha… |
| 1.3.6.1.4.1.20044.48.2.2.3.8.4 | Scalarpm801rrAlmClientHwFail | read-only | current | Line 1 Port HW Failure :This OID indicates a failure on Line 1 port, most probably caused by a HW issue. <Condtype> CLIENT_HW_FAIL <Probcause> equipmentMalfunc… |
| 1.3.6.1.4.1.20044.48.2.2.3.8.5 | Scalarpm801rrAlmClientXfpTxOff | read-only | current | Line 1 Optical Module Laser Shutdown :This OID indicates the Line 1 optical output power is off <Help> This status indicates if the line 1 transceiver laser is… |
| 1.3.6.1.4.1.20044.48.2.2.3.8.9 | Scalarpm801rrAlmClientDdmWarning | read-only | current | Warning On Line 1 Optical Module DDM :This OID indicates a warning is present coming out of Line 1 optical interface DDM <Help> This alarm indicates if a DDM W… |
| 1.3.6.1.4.1.20044.48.2.2.3.8.10 | Scalarpm801rrAlmClientDdmAlm | read-only | current | Alarm On Line 1 Optical Module DDM :This OID indicates an alarm is present coming out of Line 1 optical interface DDM <Help> This alarm indicates if a DDM Alar… |
| 1.3.6.1.4.1.20044.48.2.2.3.8.12 | Scalarpm801rrAlmClientFail | read-only | current | Line 1 Port Failure :This OID indicates a failure on the Line 1 port <Condtype> CLIENT_FAIL <Probcause> equipmentMalfunction (16) <Alarmtype> synthesisAlarm (1… |
| 1.3.6.1.4.1.20044.48.2.2.3.8.14 | Scalarpm801rrAlmClientVccWarning | read-only | current | Line 1VCC Warning :This OID indicates an overall VCC warning is set over the Line 1 XFP <Condtype> CLIENT_VCC_WARNING <Probcause> powerProblem (36) <Alarmtype>… |
| 1.3.6.1.4.1.20044.48.2.2.3.8.15 | Scalarpm801rrAlmClientVccAlarm | read-only | current | Line 1 VCC Alarm :This OID indicates an overall VCC alarm is set over the Line 1 XFP <Condtype> CLIENT_VCC_ALARM <Probcause> powerProblem (36) <Alarmtype> equi… |
| 1.3.6.1.4.1.20044.48.2.2.3.19 | Nodepm801rrAlmclientXfpAlarms2 | |||
| 1.3.6.1.4.1.20044.48.2.2.3.19.1 | Scalarpm801rrAlmClientResetComplete | read-only | current | Not Used :This bit indicates that the internal reset process is completed and the data are available <Condtype> CLIENT_RESET_COMPLETE <Probcause> other (1) <Al… |
| 1.3.6.1.4.1.20044.48.2.2.3.19.3 | Scalarpm801rrAlmClientRxCdrNotLocked | read-only | current | Line 1 Optical Rx CDR Unlocked :This OID indicates that a loss of lock on the Line 1 receiving side CDR has been detected <Condtype> CLIENT_RX_CDR_NOT_LOCKED <… |
| 1.3.6.1.4.1.20044.48.2.2.3.19.4 | Scalarpm801rrAlmClientRxLos | read-only | current | Line 1 Loss Of Optical Signal :This bit indicates an absence of signal on the XFP/OTX <Help> This alarm indicates if an optical signal is detected on the line … |
| 1.3.6.1.4.1.20044.48.2.2.3.19.5 | Scalarpm801rrAlmClientRxNr | read-only | current | Line 1 Optical Rx Not Ready :This OID indicates that a condition has arisen leading to invalid data on the Line 1 receiving side. <Condtype> CLIENT_RX_NR <Prob… |
| 1.3.6.1.4.1.20044.48.2.2.3.19.6 | Scalarpm801rrAlmClientTxCdrNotLocked | read-only | current | Line 1 Optical Tx CDR Unlocked :This OID indicates a loss of lock on the Line 1 transmitting side CDR has been detected. <Condtype> CLIENT_TX_CDR_NOT_LOCKED <P… |
| 1.3.6.1.4.1.20044.48.2.2.3.19.7 | Scalarpm801rrAlmClientTxFault | read-only | current | Line 1 Optical Tx Failure :This OID indicates a fault condition on the Line 1 laser detected by the safety syste <Condtype> CLIENT_TX_FAULT <Probcause> transmi… |
| 1.3.6.1.4.1.20044.48.2.2.3.19.8 | Scalarpm801rrAlmClientTxNr | read-only | current | Line 1 Optical Tx Not Ready :This OID indicates a condition has arisen leading to invalid data on the Line 1 transmitting side <Condtype> CLIENT_TX_NR <Probcau… |
| 1.3.6.1.4.1.20044.48.2.2.3.19.10 | Scalarpm801rrAlmClientChannelNotAcquired | read-only | current | Line 1 DWDM Channel Not Acquired :This OID indicates the transceiver didn't tune the DWDM Channel succesfully. <Help> This status indicates the transceiver has… |
| 1.3.6.1.4.1.20044.48.2.2.3.19.14 | Scalarpm801rrAlmClientWavelengthUnlocked | read-only | current | Line 1 Optical Tx Wavelength Unlocked :This OID indicates that the Line 1 wavelength error is exceeding the manufacturer tolerance <Condtype> CLIENT_WAVELENGTH… |
| 1.3.6.1.4.1.20044.48.2.2.3.19.15 | Scalarpm801rrAlmClientTecFault | read-only | current | Line 1 Optical Tx Temp Regul. Failed :This OID indicates a failure on the Line 1 TEC module <Condtype> CLIENT_TEC_FAULT <Probcause> transmitterFailure (56) <Al… |
| 1.3.6.1.4.1.20044.48.2.2.3.19.16 | Scalarpm801rrAlmClientApdSupplyFault | read-only | current | Line 1 Rx Photodiode Power Failed :This OID indicates a failure on the Line 1 APD power supply <Condtype> CLIENT_APD_SUPPLY_FAULT <Probcause> receiverFailure (… |
| 1.3.6.1.4.1.20044.48.2.3 | Nodepm801rrAlmLine | |||
| 1.3.6.1.4.1.20044.48.2.3.1 | Nodepm801rrAlmLineNurg | |||
| 1.3.6.1.4.1.20044.48.2.3.1.25 | Nodepm801rrAlmlineXfpWarnings | |||
| 1.3.6.1.4.1.20044.48.2.3.1.25.1 | Scalarpm801rrAlmLineTxPwrLowWng | read-only | current | Line 2 Optical Tx Power Low Warning :Warning indicating that the Line 2 XFP/OTX transmitter transmitter output power is lower than the threshold value written … |
| 1.3.6.1.4.1.20044.48.2.3.1.25.2 | Scalarpm801rrAlmLineTxPwrHighWng | read-only | current | Line 2 Optical Tx Power High Warning :Warning indicating that the Line 2 XFP/OTX transmitter transmitter output power is higher than the threshold value writte… |
| 1.3.6.1.4.1.20044.48.2.3.1.25.3 | Scalarpm801rrAlmLineTxBiasLowWng | read-only | current | Line 2 Transceiver Bias Low Warning :Warning indicating that the Line 2 XFP/OTX transmitter laser bias current is lower than the threshold value written in the… |
| 1.3.6.1.4.1.20044.48.2.3.1.25.4 | Scalarpm801rrAlmLineTxBiasHighWng | read-only | current | Line 2 Transceiver Bias High Warning :Warning indicating that the Line 2 XFP/OTX transmitter laser bias current is higher than the threshold value written in t… |
| 1.3.6.1.4.1.20044.48.2.3.1.25.7 | Scalarpm801rrAlmLineTempLowWng | read-only | current | Line 2 Transceiver Temp Low Warning :Warning indicating that the Line 2 XFP/OTX temperature is lower than the threshold value written in the Line 2 XFP/OTX EEP… |
| 1.3.6.1.4.1.20044.48.2.3.1.25.8 | Scalarpm801rrAlmLineTempHighWng | read-only | current | Line 2 Transceiver Temp High Warning :Warning indicating that the Line 2 XFP/OTX temperature is higher than the threshold value written in the Line 2 XFP/OTX E… |
| 1.3.6.1.4.1.20044.48.2.3.1.25.15 | Scalarpm801rrAlmLineRxPwrLowWng | read-only | current | Line 2 Optical Rx Power Low Warning :Warning indicating that the Line 2 XFP/OTX received optical power is lower than the threshold value written in the Line 2 … |
| 1.3.6.1.4.1.20044.48.2.3.1.25.16 | Scalarpm801rrAlmLineRxPwrHighWng | read-only | current | Line 2 Optical Rx Power High Warning :Warning indicating that the Line 2 XFP/OTX received optical power is higher than the threshold value written in the Line … |
| 1.3.6.1.4.1.20044.48.2.3.1.31 | Nodepm801rrAlmrrLineOtxTlhWarnings | |||
| 1.3.6.1.4.1.20044.48.2.3.1.31.5 | Scalarpm801rrAlmLineModulatorAgingHighWarning | read-only | current | Line 2 Modulator Aging High Warning :Warning indicating the Line 2 OTX TLH modulator aging is higher than the threshold written in the EEPROM <Condtype> LINE_M… |
| 1.3.6.1.4.1.20044.48.2.3.1.31.6 | Scalarpm801rrAlmLineAgingHighWarning | read-only | current | Line 2 OTX TLH Aging High Warning :Warning indicating the Line 2 OTX TLH aging is higher than the threshold written in the EEPROM <Condtype> LINE_AGING_HIGH_WA… |
| 1.3.6.1.4.1.20044.48.2.3.1.31.12 | Scalarpm801rrAlmLineFreqDevHighWarning | read-only | current | Line 2 Freq. Deviation High Warning :Warning indicating the Line 2 OTX TLH frequency deviation is higher than the threshold written in the EEPROM <Condtype> LI… |
| 1.3.6.1.4.1.20044.48.2.3.1.31.14 | Scalarpm801rrAlmLineLaserTempHighWarning | read-only | current | Line 2 Laser Temp. High Warning :Warning indicating the Line 2 OTX TLH laser temperature is higher than the threshold written in the EEPROM <Condtype> LINE_LAS… |
| 1.3.6.1.4.1.20044.48.2.3.2 | Nodepm801rrAlmLineUrg | |||
| 1.3.6.1.4.1.20044.48.2.3.2.24 | Nodepm801rrAlmlineXfpAlarm1 | |||
| 1.3.6.1.4.1.20044.48.2.3.2.24.1 | Scalarpm801rrAlmLineTxPwrLowAla | read-only | current | Line 2 Optical Tx Power Low :Alarm indicating that the Line 2 XFP/OTX transmitter transmitter output power is lower than the threshold value written in the Lin… |
| 1.3.6.1.4.1.20044.48.2.3.2.24.2 | Scalarpm801rrAlmLineTxPwrHighAla | read-only | current | Line 2 Optical Tx Power High :Alarm indicating that the Line 2 XFP/OTX transmitter transmitter output power is higher than the threshold value written in the L… |
| 1.3.6.1.4.1.20044.48.2.3.2.24.3 | Scalarpm801rrAlmLineTxBiasLowAla | read-only | current | Line 2 Transceiver Bias Low :Alarm indicating that the Line 2 XFP/OTX transmitter laser bias current is lower than the threshold value written in the Line 2 XF… |
| 1.3.6.1.4.1.20044.48.2.3.2.24.4 | Scalarpm801rrAlmLineTxBiasHighAla | read-only | current | Line 2 Transceiver Bias High :Alarm indicating that the Line 2 XFP/OTX transmitter laser bias current is higher than the threshold value written in the Line 2 … |
| 1.3.6.1.4.1.20044.48.2.3.2.24.7 | Scalarpm801rrAlmLineTempLowAla | read-only | current | Line 2 Transceiver Temp Low :Alarm indicating that the Line 2 XFP/OTX temperature is lower than the threshold value written in the Line 2 XFP/OTX EEPROM <Condt… |
| 1.3.6.1.4.1.20044.48.2.3.2.24.8 | Scalarpm801rrAlmLineTempHighAla | read-only | current | Line 2 Transceiver Temp High :Alarm indicating that the Line 2 XFP/OTX temperature is higher than the threshold value written in the Line 2 XFP/OTX EEPROM <Con… |
| 1.3.6.1.4.1.20044.48.2.3.2.24.15 | Scalarpm801rrAlmLineRxPwrLowAla | read-only | current | Line 2 Optical Rx Power Low :Alarm indicating that the Line 2 XFP/OTX received optical power is lower than the threshold value written in the Line 2 XFP/OTX EE… |
| 1.3.6.1.4.1.20044.48.2.3.2.24.16 | Scalarpm801rrAlmLineRxPwrHighAla | read-only | current | Line 2 Optical Rx Power High :Alarm indicating that the Line 2 XFP/OTX received optical power is higher than the threshold value written in the Line 2 XFP/OTX … |
| 1.3.6.1.4.1.20044.48.2.3.2.30 | Nodepm801rrAlmrrLineOtxTlhAlarms3 | |||
| 1.3.6.1.4.1.20044.48.2.3.2.30.5 | Scalarpm801rrAlmLineModulatorAgingHighAla | read-only | current | Line 2 Modulator Aging High Alarm :Alarm indicating the Line 2 OTX TLH modulator aging is higher than the threshold written in the EEPROM <Condtype> LINE_MODUL… |
| 1.3.6.1.4.1.20044.48.2.3.2.30.6 | Scalarpm801rrAlmLineAgingHighAla | read-only | current | Line 2 OTX TLH Aging High Alarm :Alarm indicating the Line 2 OTX TLH aging is higher than the threshold written in the EEPROM <Condtype> LINE_AGING_HIGH_ALA <P… |
| 1.3.6.1.4.1.20044.48.2.3.2.30.9 | Scalarpm801rrAlmLineCdrNotReady | read-only | current | Line 2 CDR Not Ready :This OID indicates the Clock Data Recovery unit is not yet initialized <Help> This alarm indicates the Clock Data Recovery unit is not ye… |
| 1.3.6.1.4.1.20044.48.2.3.2.30.12 | Scalarpm801rrAlmLineFreqDevHighAla | read-only | current | Line 2 Freq. Deviation High Alarm :Alarm indicating the Line 2 OTX TLH frequency deviation is higher than the threshold written in the EEPROM <Condtype> LINE_F… |
| 1.3.6.1.4.1.20044.48.2.3.2.30.14 | Scalarpm801rrAlmLineLaserTempHighAla | read-only | current | Line 2 Laser Temp. High Alarm :Alarm indicating the Line 2 OTX TLH laser temperature is higher than the threshold written in the EEPROM <Condtype> LINE_LASER_T… |
| 1.3.6.1.4.1.20044.48.2.3.3 | Nodepm801rrAlmLineCrit | |||
| 1.3.6.1.4.1.20044.48.2.3.3.7 | Nodepm801rrAlmsynthAlm7 | |||
| 1.3.6.1.4.1.20044.48.2.3.3.7.1 | Scalarpm801rrAlmLineXfpAbsent | read-only | current | Line 2 Optical Module Absent :This OID indicates the Line 2 optical interface (XFP or OTX) is not present in the PM <Help> This alarm indicates if the line 2 t… |
| 1.3.6.1.4.1.20044.48.2.3.3.7.2 | Scalarpm801rrAlmLineInitNotCompl | read-only | current | Line 2 Optical Module Ready :This OID indicates the optical interface (XFP or OTX) is not operational <Help> This status indicates if the line 2 transceiver ha… |
| 1.3.6.1.4.1.20044.48.2.3.3.7.4 | Scalarpm801rrAlmLineHwFail | read-only | current | Line 2 Port HW Failure :This OID indicates a failure on Line 2 port, most probably caused by a HW issue <Condtype> LINE_HW_FAIL <Probcause> equipmentMalfunctio… |
| 1.3.6.1.4.1.20044.48.2.3.3.7.5 | Scalarpm801rrAlmLineXfpTxOff | read-only | current | Line 2 Optical Module Laser Shutdown :This OID indicates the Line 2 optical output power is off <Help> This status indicates if the line 2 transceiver laser is… |
| 1.3.6.1.4.1.20044.48.2.3.3.7.9 | Scalarpm801rrAlmLineDdmWarning | read-only | current | Warning On Line 2 Optical Module DDM :This OID indicates a warning is present coming out of Line 2 optical interface DDM <Help> This alarm indicates if a DDM W… |
| 1.3.6.1.4.1.20044.48.2.3.3.7.10 | Scalarpm801rrAlmLineDdmAlm | read-only | current | Alarm On Line 2 Optical Module DDM :This OID indicates an alarm is present coming out of Line 2 optical interface DDM <Help> This alarm indicates if a DDM Alar… |
| 1.3.6.1.4.1.20044.48.2.3.3.7.12 | Scalarpm801rrAlmLineFail | read-only | current | Line 2 Port Failure :This OID indicates a failure on the Line 2 port <Condtype> LINE_FAIL <Probcause> equipmentMalfunction (16) <Alarmtype> synthesisAlarm (12)… |
| 1.3.6.1.4.1.20044.48.2.3.3.7.14 | Scalarpm801rrAlmLineVccWarning | read-only | current | Line 2 VCC Warning :This OID indicates an overall VCC warning is set over the Line 2 XFP <Condtype> LINE_VCC_WARNING <Probcause> powerProblem (36) <Alarmtype> … |
| 1.3.6.1.4.1.20044.48.2.3.3.7.15 | Scalarpm801rrAlmLineVccAlarm | read-only | current | Line 2 VCC Alarm :This OID indicates an overall VCC alarm is set over the Line 2 XFP <Condtype> LINE_VCC_ALARM <Probcause> powerProblem (36) <Alarmtype> equipm… |
| 1.3.6.1.4.1.20044.48.2.3.3.27 | Nodepm801rrAlmlineXfpAlarms2 | |||
| 1.3.6.1.4.1.20044.48.2.3.3.27.1 | Scalarpm801rrAlmLineResetComplete | read-only | current | Not Used :This bit indicates that the internal reset process is completed and the data are available <Condtype> LINE_RESET_COMPLETE <Probcause> other (1) <Alar… |
| 1.3.6.1.4.1.20044.48.2.3.3.27.3 | Scalarpm801rrAlmLineRxCdrNotLocked | read-only | current | Line 2 Optical Rx CDR Unlocked :This OID indicates that a loss of lock on the Line 2 receiving side CDR has been detected <Condtype> LINE_RX_CDR_NOT_LOCKED <Pr… |
| 1.3.6.1.4.1.20044.48.2.3.3.27.4 | Scalarpm801rrAlmLineRxLos | read-only | current | Line 2 Loss Of Optical Signal :This bit indicates an absence of signal on the XFP/OTX <Help> This alarm indicates if an optical signal is detected on the line … |
| 1.3.6.1.4.1.20044.48.2.3.3.27.5 | Scalarpm801rrAlmLineRxNr | read-only | current | Line 2 Optical Rx Not Ready :This OID indicates that a condition has arisen leading to invalid data on the Line 2 receiving side. <Condtype> LINE_RX_NR <Probca… |
| 1.3.6.1.4.1.20044.48.2.3.3.27.6 | Scalarpm801rrAlmLineTxCdrNotLocked | read-only | current | Line 2 Optical Tx CDR Unlocked :This OID indicates a loss of lock on the Line 2 transmitting side CDR has been detected. <Condtype> LINE_TX_CDR_NOT_LOCKED <Pro… |
| 1.3.6.1.4.1.20044.48.2.3.3.27.7 | Scalarpm801rrAlmLineTxFault | read-only | current | Line 2 Optical Tx Failure :This OID indicates a fault condition on the Line 2 laser detected by the safety syste <Condtype> LINE_TX_FAULT <Probcause> transmitt… |
| 1.3.6.1.4.1.20044.48.2.3.3.27.8 | Scalarpm801rrAlmLineTxNr | read-only | current | Line 2 Optical Tx Not Ready :This OID indicates a condition has arisen leading to invalid data on the Line 2 transmitting side <Condtype> LINE_TX_NR <Probcause… |
| 1.3.6.1.4.1.20044.48.2.3.3.27.10 | Scalarpm801rrAlmLineChannelNotAcquired | read-only | current | Line 2 DWDM Channel Not Acquired :This OID indicates the transceiver didn't tune the DWDM Channel succesfully. <Help> This status indicates the transceiver has… |
| 1.3.6.1.4.1.20044.48.2.3.3.27.14 | Scalarpm801rrAlmLineWavelengthUnlocked | read-only | current | Line 2 Optical Tx Wavelength Unlocked :This OID indicates that the Line 2 wavelength error is exceeding the manufacturer tolerance <Condtype> LINE_WAVELENGTH_U… |
| 1.3.6.1.4.1.20044.48.2.3.3.27.15 | Scalarpm801rrAlmLineTecFault | read-only | current | Line 2 Optical Tx Temp Regul. Failed :This OID indicates a failure on the Line 2 TEC module <Condtype> LINE_TEC_FAULT <Probcause> transmitterFailure (56) <Alar… |
| 1.3.6.1.4.1.20044.48.2.3.3.27.16 | Scalarpm801rrAlmLineApdSupplyFault | read-only | current | Line 2 Rx Photodiode Power Failed :This OID indicates a failure on the Line 2 APD power supply <Condtype> LINE_APD_SUPPLY_FAULT <Probcause> receiverFailure (42… |
| 1.3.6.1.4.1.20044.48.3 | Nodepm801rrmeasures | |||
| 1.3.6.1.4.1.20044.48.3.1 | Nodepm801rrMesrOther | |||
| 1.3.6.1.4.1.20044.48.3.2 | Nodepm801rrMesrClient | |||
| 1.3.6.1.4.1.20044.48.3.2.16 | Scalarpm801rrMesrclientTemperature | read-only | current | Line 1 Optical Module Temperature :This OID gives the temperature of the Client XFP/OTX, read from the DDM (Digital Diagnostic Monitoring) (Temperature = AV/25… |
| 1.3.6.1.4.1.20044.48.3.2.18 | Scalarpm801rrMesrclientTxBias | read-only | current | Line 1 XFP/OTX Tx Bias Current :This OID gives the bias value of the Client XFP/OTX, read from the DDM (Digital Diagnostic Monitoring) (Bias = AV/500) (Unit = … |
| 1.3.6.1.4.1.20044.48.3.2.19 | Scalarpm801rrMesrclientTxPower | read-only | current | Line 1 Optical Module Tx Power :This OID gives the transmit power value of the Client XFP/OTX, read from the DDM (Digital Diagnostic Monitoring) (Power = 10*lo… |
| 1.3.6.1.4.1.20044.48.3.2.20 | Scalarpm801rrMesrclientRxPower | read-only | current | Line 1 Optical Module Rx Power :This OID gives the receive power value of the Client XFP/OTX, read from the DDM (Digital Diagnostic Monitoring) (Power = 10*log… |
| 1.3.6.1.4.1.20044.48.3.2.32 | Scalarpm801rrMesrclientAging | read-only | current | Line 1 OTX TLH Aging :This OID gives the aging of the Line 1 OTX TLH, read from the DDM (Digital Diagnostic Monitoring) (Aging = AV) (Unit = %) <Help> This mea… |
| 1.3.6.1.4.1.20044.48.3.2.33 | Scalarpm801rrMesrclientLaserTemperature | read-only | current | Line 1 OTX TLH Laser Temperature :This OID gives the laser temperature of the Line 1 OTX TLH, read from the DDM (Digital Diagnostic Monitoring) (Temperature = … |
| 1.3.6.1.4.1.20044.48.3.2.34 | Scalarpm801rrMesrclientFreqDeviation | read-only | current | Line 1 OTX TLH Frequency Deviation :This OID gives the frequency deviation of the Line 1 OTX TLH, read from the DDM (Digital Diagnostic Monitoring) (Deviation … |
| 1.3.6.1.4.1.20044.48.3.2.35 | Scalarpm801rrMesrclientLaserWvlength | read-only | current | Line 1 Optical Module Wavelength :This OID gives the laser wavelength of the Line 1 OTX TLH, read from the DDM (Digital Diagnostic Monitoring) (Wavelength=2997… |
| 1.3.6.1.4.1.20044.48.3.3 | Nodepm801rrMesrLine | |||
| 1.3.6.1.4.1.20044.48.3.3.24 | Scalarpm801rrMesrlineTemperature | read-only | current | Line 2 Optical Module Temperature :This OID gives the temperature of the Line XFP/OTX, read from the DDM (Digital Diagnostic Monitoring) (Temperature = AV/256)… |
| 1.3.6.1.4.1.20044.48.3.3.26 | Scalarpm801rrMesrlineTxBias | read-only | current | Line 2 XFP/OTX Tx Bias Current :This OID gives the bias value of the Line XFP/OTX, read from the DDM (Digital Diagnostic Monitoring) (Bias = AV/500) (Unit = mA… |
| 1.3.6.1.4.1.20044.48.3.3.27 | Scalarpm801rrMesrlineTxPower | read-only | current | Line 2 Optical Module Tx Power :This OID gives the transmit power value of the Line XFP/OTX, read from the DDM (Digital Diagnostic Monitoring) (Power = 10*log(… |
| 1.3.6.1.4.1.20044.48.3.3.28 | Scalarpm801rrMesrlineRxPower | read-only | current | Line 2 Optical Module Rx Power :This OID gives the receive power value of the Line XFP/OTX, read from the DDM (Digital Diagnostic Monitoring) (Power = 10*log(A… |
| 1.3.6.1.4.1.20044.48.3.3.40 | Scalarpm801rrMesrlineAging | read-only | current | Line 2 OTX TLH Aging :This OID gives the aging of the Line 2 OTX TLH, read from the DDM (Digital Diagnostic Monitoring) (Aging = AV) (Unit = %) <Help> This mea… |
| 1.3.6.1.4.1.20044.48.3.3.41 | Scalarpm801rrMesrlineLaserTemperature | read-only | current | Line 2 OTX TLH Laser Temperature :This OID gives the laser temperature of the Line 2 OTX TLH, read from the DDM (Digital Diagnostic Monitoring) (Temperature = … |
| 1.3.6.1.4.1.20044.48.3.3.42 | Scalarpm801rrMesrlineFreqDeviation | read-only | current | Line 2 OTX TLH Frequency Deviation :This OID gives the frequency deviation of the Line 2 OTX TLH, read from the DDM (Digital Diagnostic Monitoring) (Deviation … |
| 1.3.6.1.4.1.20044.48.3.3.43 | Scalarpm801rrMesrlineLaserWvlength | read-only | current | Line 2 Optical Module Wavelength :This OID gives the laser wavelength of the Line 2 OTX TLH, read from the DDM (Digital Diagnostic Monitoring) (Wavelength=2997… |
| 1.3.6.1.4.1.20044.48.6 | Nodepm801rrcontrolsWrite | |||
| 1.3.6.1.4.1.20044.48.6.1 | Nodepm801rrCtrlOther | |||
| 1.3.6.1.4.1.20044.48.6.1.0 | Nodepm801rrCtrlsynth0 | |||
| 1.3.6.1.4.1.20044.48.6.1.0.1 | Scalarpm801rrCtrlConfLoad | read-write | current | Load Configuration Tables :When set this enables loading from flash configuration1 into the module. |
| 1.3.6.1.4.1.20044.48.6.1.0.9 | Scalarpm801rrCtrlConfFlash | read-write | current | Write Configuration Tables :This bit saves the current configuration of the module as configuration in the flash. <Help> This control saves the customer config… |
| 1.3.6.1.4.1.20044.48.6.1.0.13 | Scalarpm801rrCtrlConfClear | read-write | current | Clear Configuration Tables :This bit clears the configuration tables from configuration in the flash. <Help> This control restores the default configuration of… |
| 1.3.6.1.4.1.20044.48.6.1.4 | Nodepm801rrCtrlsynth4 | |||
| 1.3.6.1.4.1.20044.48.6.1.4.1 | Scalarpm801rrCtrlCorrelatOn | read-write | current | Enable Alarm Correlation :This OID enables the alarm correlation in the PM |
| 1.3.6.1.4.1.20044.48.6.1.4.2 | Scalarpm801rrCtrlCorrelatOff | read-write | current | Disable Alarm Correlation :This OID disables the alarm correlation in the PM |
| 1.3.6.1.4.1.20044.48.6.1.5 | Nodepm801rrCtrlswMgnt | |||
| 1.3.6.1.4.1.20044.48.6.1.5.2 | Scalarpm801rrCtrlColdReset | read-write | current | Software Cold Reset :This OID, when set, causes a cold reset of the Software. This reset is traffic affecting, and the configuration of Software is reloaded on… |
| 1.3.6.1.4.1.20044.48.6.1.5.3 | Scalarpm801rrCtrlWarmReset | read-write | current | Software Warm Reset :This OID, when set, causes a warm reset of the Software. This reset is not traffic affecting, and the configuration of the Sofwtare remain… |
| 1.3.6.1.4.1.20044.48.6.1.64 | Nodepm801rrCtrlledTest | |||
| 1.3.6.1.4.1.20044.48.6.1.64.1 | Scalarpm801rrCtrlGreenLed | read-write | current | Green Leds Test :This OID switches on all the green Leds as a test feature. <Help> This control initiates a test leds turning all the LEDs to green |
| 1.3.6.1.4.1.20044.48.6.1.64.2 | Scalarpm801rrCtrlRedLed | read-write | current | Red Leds Test :This OID switches on all the red Leds as a test feature. <Help> This control initiates a test leds turning all the LEDs to red |
| 1.3.6.1.4.1.20044.48.6.1.64.3 | Scalarpm801rrCtrlLedOff | read-write | current | Leds Off :This OID switches off all the Leds as a test feature. <Help> This control initiates a test leds turning all the LEDs to OFF |
| 1.3.6.1.4.1.20044.48.6.2 | Nodepm801rrCtrlClient | |||
| 1.3.6.1.4.1.20044.48.6.2.16 | Nodepm801rrCtrlclientXfpOnoff | |||
| 1.3.6.1.4.1.20044.48.6.2.16.1 | Scalarpm801rrCtrlClientXfpOnoff | read-write | current | XFP/OTX Laser Shut Down :This OID switches off the Line 1 XFP/OTX <Help> This control defines the laser state of the line 1 transceiver |
| 1.3.6.1.4.1.20044.48.6.2.17 | Nodepm801rrCtrlclientXfpLineLoop | |||
| 1.3.6.1.4.1.20044.48.6.2.17.1 | Scalarpm801rrCtrlClientXfpLineLoop | read-write | current | XFP/OTX Loop :This OID operates a loopback on the Line 1 XFP/OTX <Help> This control defines the line loop back of the line 1 transceiver |
| 1.3.6.1.4.1.20044.48.6.2.18 | Nodepm801rrCtrlclientXfiLoop | |||
| 1.3.6.1.4.1.20044.48.6.2.18.1 | Scalarpm801rrCtrlClientXfiLoop | read-write | current | XFP/OTX XFI Loop :This OID operates a XFI loopback on the Line 1 XFP/OTX <Help> This control defines the XFI loop back of the line transceiver |
| 1.3.6.1.4.1.20044.48.6.2.19 | Scalarpm801rrCtrlclientTunableChannel | read-write | current | ITU Channel :This OID selects the ITU channel of the Line 1 OTX TLH Laser <Help> This control defines the ITU channel of the Line 1 OTX TLH Laser |
| 1.3.6.1.4.1.20044.48.6.2.20 | Scalarpm801rrCtrlclientPhotodiodeMode | read-write | current | OTX TLH Rx Sens. Mode :This OID defines the Rx sensiblity mode of the Line 1 OTX TLH <Help> This control defines the receiver sensibility mode of the Line 1 OT… |
| 1.3.6.1.4.1.20044.48.6.2.21 | Scalarpm801rrCtrlclientPhotodiodeValue | read-write | current | OTX TLH Rx Sensibility :This OID sets the Rx sensibility of the Line 1 OTX TLH (custom mode only) <Help> This control defines the receiver sensibility value (o… |
| 1.3.6.1.4.1.20044.48.6.2.22 | Scalarpm801rrCtrlclientPowerLaser | read-write | current | Laser Output Power [3-5] :This OID sets the output power value on the laser of the Line 1 OTX TLH (AV=Power*10+158) (Unit = dBm) <Help> This control defines th… |
| 1.3.6.1.4.1.20044.48.6.3 | Nodepm801rrCtrlLine | |||
| 1.3.6.1.4.1.20044.48.6.3.23 | Nodepm801rrCtrlclientOtxVlhReset | |||
| 1.3.6.1.4.1.20044.48.6.3.23.1 | Scalarpm801rrCtrlClientOtxVlhReset | read-write | current | OTX-VLH Reset :This OID resets the OTX-VLH module <Help> This control resets the OTX-TLH and its parameters |
| 1.3.6.1.4.1.20044.48.6.3.24 | Nodepm801rrCtrllineXfpOnoff | |||
| 1.3.6.1.4.1.20044.48.6.3.24.1 | Scalarpm801rrCtrlLineXfpOnoff | read-write | current | XFP/OTX Laser Shut Down :This OID switches off the Line 2 XFP/OTX <Help> This control defines the laser state of the line 2 transceiver |
| 1.3.6.1.4.1.20044.48.6.3.25 | Nodepm801rrCtrllineXfpLineLoop | |||
| 1.3.6.1.4.1.20044.48.6.3.25.1 | Scalarpm801rrCtrlLineXfpLineLoop | read-write | current | XFP/OTX Loop :This OID operates a loopback on the Line 2 XFP/OTX <Help> This control defines the line loop back of the line 2 transceiver |
| 1.3.6.1.4.1.20044.48.6.3.26 | Nodepm801rrCtrllineXfiLoop | |||
| 1.3.6.1.4.1.20044.48.6.3.26.1 | Scalarpm801rrCtrlLineXfiLoop | read-write | current | XFP/OTX XFI Loop :This OID operates a XFI loopback on the Line 2 XFP/OTX <Help> This control defines the XFI loop back of the line 2 transceiver |
| 1.3.6.1.4.1.20044.48.6.3.27 | Scalarpm801rrCtrllineTunableChannel | read-write | current | ITU Channel :This OID selects the ITU channel of the Line 2 OTX TLH Laser <Help> This control defines the ITU channel of the Line 2 OTX TLH Laser |
| 1.3.6.1.4.1.20044.48.6.3.28 | Scalarpm801rrCtrllinePhotodiodeMode | read-write | current | OTX TLH Rx Sens. Mode :This OID defines the Rx sensiblity mode of the Line 2 OTX TLH <Help> This control defines the receiver sensibility mode of the Line 2 OT… |
| 1.3.6.1.4.1.20044.48.6.3.29 | Scalarpm801rrCtrllinePhotodiodeValue | read-write | current | OTX TLH Rx Sensibility :This OID sets the Rx sensibility of the Line 2 OTX TLH (custom mode only) <Help> This control defines the receiver sensibility value (o… |
| 1.3.6.1.4.1.20044.48.6.3.30 | Scalarpm801rrCtrllinePowerLaser | read-write | current | Laser Output Power [3-5] :This OID sets the output power value on the laser of the Line 2 OTX TLH (AV=Power*10+158) (Unit = dBm) <Help> This control defines th… |
| 1.3.6.1.4.1.20044.48.6.3.31 | Nodepm801rrCtrllineOtxVlhReset | |||
| 1.3.6.1.4.1.20044.48.6.3.31.1 | Scalarpm801rrCtrlLineOtxVlhReset | read-write | current | OTX-VLH Reset :This OID resets the OTX-VLH module <Help> This control resets the OTX-TLH and its parameters |
| 1.3.6.1.4.1.20044.48.7 | Nodepm801rrri | |||
| 1.3.6.1.4.1.20044.48.7.2 | Scalarpm801rrRinvReloadInventory | read-write | current | Reload the inventory: This OID triggers an inventory reload. |
| 1.3.6.1.4.1.20044.48.7.4 | Scalarpm801rrRinvHwPlatform | read-only | current | Module platform description: This OID contains the description of the Module. |
| 1.3.6.1.4.1.20044.48.7.5 | Scalarpm801rrRinvSwPlatform | read-only | current | SW platform description: This OID contains the description of the Software platform. |
| 1.3.6.1.4.1.20044.48.7.6 | Scalarpm801rrRinvClientXFP | read-only | current | Inventory for the XFP: This OID contains the inventory for the Client XFP |
| 1.3.6.1.4.1.20044.48.7.7 | Scalarpm801rrRinvLineXFP | read-only | current | Inventory for the XFP: This OID contains the inventory for the Line XFP |
| 1.3.6.1.4.1.20044.48.9 | Nodepm801rrConfig | |||
| 1.3.6.1.4.1.20044.48.9.1 | Nodepm801rrCfgLsd | |||
| 1.3.6.1.4.1.20044.48.9.1.1 | Nodepm801rrtableclientLsd | |||
| 1.3.6.1.4.1.20044.48.9.1.1.2 | Scalarpm801rrCfglsdMode | read-write | current | LSD mode on Client/Line Port :This OID enables/disables the automatic laser shutdown on the Client and Line ports |
| 1.3.6.1.4.1.20044.48.9.1.1.3 | Scalarpm801rrCfgclientXfpAlarms | read-write | current | LSD contributors on Client port :This OID configures the contributors for the automatic laser shutdown of the client port |
| 1.3.6.1.4.1.20044.48.9.1.1.4 | Scalarpm801rrCfgclientXfpAbsence | read-write | current | LSD contributors on Client port :This OID configures the contributors for the automatic laser shutdown of the client port |
| 1.3.6.1.4.1.20044.48.9.1.1.5 | Scalarpm801rrCfglineXfpAlarms | read-write | current | LSD contributors on Line port :This OID configures the contributors for the automatic laser shutdown of the line port |
| 1.3.6.1.4.1.20044.48.9.1.1.6 | Scalarpm801rrCfglineXfpAbsence | read-write | current | LSD contributors on Line port :This OID configures the contributors for the automatic laser shutdown of the line port |
| 1.3.6.1.4.1.20044.48.9.2 | Nodepm801rrCfgStartUp | |||
| 1.3.6.1.4.1.20044.48.9.2.1 | Nodepm801rrtableclientStartup | |||
| 1.3.6.1.4.1.20044.48.9.2.1.2 | Scalarpm801rrCfgclientXfpCtrl | read-write | current | Default Settings on Line 1 Port :This register configures the default initialisation settings on the client port. |
| 1.3.6.1.4.1.20044.48.9.2.2 | Nodepm801rrtablelineStartup | |||
| 1.3.6.1.4.1.20044.48.9.2.2.2 | Scalarpm801rrCfglineXfpCtrl | read-write | current | Default Settings on Line 2 Port :This register configures the default initialisation settings on the line port. |
| 1.3.6.1.4.1.20044.48.9.2.2.18 | Scalarpm801rrCfgprotocolSelect | read-write | current | Bitrate selection on Line/Client port :This OID register configure the bitrate for the client and line interface (0=9,953 Gb/s - 1=10,3125 Gb/s - 2=9,953 Gb/s … |
| 1.3.6.1.4.1.20044.48.9.2.3 | Nodepm801rrtableclientOtxtlh | |||
| 1.3.6.1.4.1.20044.48.9.2.3.2 | Scalarpm801rrCfgclientDitherControl | read-write | current | Default Settings on Dither Line 1 :This register configures the default initialisation settings on the dither of the client port. |
| 1.3.6.1.4.1.20044.48.9.2.3.3 | Scalarpm801rrCfgclientDitherRate | read-write | current | Default Line 1 OTX TLH FM amplitude :This register configures the start-up width of the frequency modulation of the line 1 OTX TLH |
| 1.3.6.1.4.1.20044.48.9.2.3.4 | Scalarpm801rrCfgclientDitherFhz | read-write | current | Default Line 1 OTX TLH FM frequency :This register configures the start-up frequency of the frequency modulation of the line 1 OTX TLH |
| 1.3.6.1.4.1.20044.48.9.2.3.5 | Scalarpm801rrCfgclientPwrLaser | read-write | current | Defaut Line 1 OTX TLH output Power :This register configures the start-up output power of the line 1 OTX TLH (Unit = dBm) |
| 1.3.6.1.4.1.20044.48.9.2.3.6 | Scalarpm801rrCfgclientFCurrent | read-write | current | Default Line 1 OTX TLH Channel :This register configures the start-up laser channel of the line 1 OTX TLH |
| 1.3.6.1.4.1.20044.48.9.2.3.7 | Scalarpm801rrCfgclientGridCurrent | read-write | current | Default Line 1 OTX TLH Grid :This register configures the start-up laser grid of the line 1 OTX TLH |
| 1.3.6.1.4.1.20044.48.9.2.3.8 | Scalarpm801rrCfgclientF0 | read-write | current | Default Line 1 OTX TLH lowest Freq :This register configures the start-up lowest frequency supported on the line 1 OTX TLH |
| 1.3.6.1.4.1.20044.48.9.2.3.10 | Scalarpm801rrCfgclientPhotodiodeMode | read-write | current | Default Line 1 OTX TLH APD mode :This register configures the start-up APD mode of the line 1 OTX TLH |
| 1.3.6.1.4.1.20044.48.9.2.3.11 | Scalarpm801rrCfgclientPhotodiodeValue | read-write | current | Default Line 1 OTX TLH APD atten. :This register configures the start-up APD attenuation on the line 1 OTX TLH |
| 1.3.6.1.4.1.20044.48.9.2.4 | Nodepm801rrtablelineOtxtlh | |||
| 1.3.6.1.4.1.20044.48.9.2.4.2 | Scalarpm801rrCfglineDitherControl | read-write | current | Default Settings on Dither Line 2 :This register configures the default initialisation settings on the dither of the client port. |
| 1.3.6.1.4.1.20044.48.9.2.4.3 | Scalarpm801rrCfglineDitherRate | read-write | current | Default Line 2 OTX TLH FM amplitude :This register configures the start-up width of the frequency modulation of the line 2 OTX TLH |
| 1.3.6.1.4.1.20044.48.9.2.4.4 | Scalarpm801rrCfglineDitherFhz | read-write | current | Default Line 2 OTX TLH FM frequency :This register configures the start-up frequency of the frequency modulation of the line 2 OTX TLH |
| 1.3.6.1.4.1.20044.48.9.2.4.5 | Scalarpm801rrCfglinePwrLaser | read-write | current | Defaut Line 2 OTX TLH output Power :This register configures the start-up output power of the line 2 OTX TLH (Unit = dBm) |
| 1.3.6.1.4.1.20044.48.9.2.4.6 | Scalarpm801rrCfglineFCurrent | read-write | current | Default Line 2 OTX TLH Channel :This register configures the start-up laser channel of the line 2 OTX TLH |
| 1.3.6.1.4.1.20044.48.9.2.4.7 | Scalarpm801rrCfglineGridCurrent | read-write | current | Default Line 2 OTX TLH Grid :This register configures the start-up laser grid of the line 2 OTX TLH |
| 1.3.6.1.4.1.20044.48.9.2.4.8 | Scalarpm801rrCfglineF0 | read-write | current | Default Line 2 OTX TLH lowest Freq :This register configures the start-up lowest frequency supported on the line 2 OTX TLH |
| 1.3.6.1.4.1.20044.48.9.2.4.10 | Scalarpm801rrCfglinePhotodiodeMode | read-write | current | Default Line 2 OTX TLH APD mode :This register configures the start-up APD mode of the line 2 OTX TLH |
| 1.3.6.1.4.1.20044.48.9.2.4.11 | Scalarpm801rrCfglinePhotodiodeValue | read-write | current | Default Line 2 OTX TLH APD atten. :This register configures the start-up APD attenuation on the line 2 OTX TLH |
| 1.3.6.1.4.1.20044.48.9.3 | Nodepm801rrCfgLabels | |||
| 1.3.6.1.4.1.20044.48.9.3.1 | Tablepm801rrCfgLabelclientTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.48.9.3.1.1 | Rowpm801rrCfgLabelclientEntry | not-accessible | current | Row definition for the labels table |
| 1.3.6.1.4.1.20044.48.9.3.1.1.1 | Columnpm801rrCfgLabelclientIndex | read-only | current | Index definition for the labelclient table |
| 1.3.6.1.4.1.20044.48.9.3.1.1.3 | Columnpm801rrCfgLabelclientPortn | read-write | current | Default settings on the label of the Ports :These registers configures the default initialisation settings of the labels of the ports. |
| 1.3.6.1.4.1.20044.48.9.3.2 | Tablepm801rrCfgLabellineTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.48.9.3.2.1 | Rowpm801rrCfgLabellineEntry | not-accessible | current | Row definition for the labels table |
| 1.3.6.1.4.1.20044.48.9.3.2.1.1 | Columnpm801rrCfgLabellineIndex | read-only | current | Index definition for the labelline table |
| 1.3.6.1.4.1.20044.48.9.3.2.1.3 | Columnpm801rrCfgLabellinePortn | read-write | current | Default settings on the label of the lines :These registers configures the default initialisation settings of the labels of the lines. |
| 1.3.6.1.4.1.20044.48.9.4 | Nodepm801rrCfgStartuptablefive | |||
| 1.3.6.1.4.1.20044.48.9.4.1 | Tablepm801rrCfgOtxtlhcapabilitiesTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.48.9.4.1.1 | Rowpm801rrCfgOtxtlhcapabilitiesEntry | not-accessible | current | Row definition for the startuptablefive table |
| 1.3.6.1.4.1.20044.48.9.4.1.1.1 | Columnpm801rrCfgOtxtlhcapabilitiesIndex | read-only | current | Index definition for the otxtlhcapabilities table |
| 1.3.6.1.4.1.20044.48.9.4.1.1.3 | Columnpm801rrCfgComponentTypePortn | read-only | current | Component parameters :This OID defines the component parameters |
| 1.3.6.1.4.1.20044.48.9.4.1.1.4 | Columnpm801rrCfgMiscellaneousPortn | read-only | current | Miscellaneous default settings :This OID defines the miscellaneous parameters |
| 1.3.6.1.4.1.20044.48.9.4.1.1.5 | Columnpm801rrCfgFirstChannelPortn | read-only | current | Number of the first channel of the component :This OID defines the first channel number of the PM |
| 1.3.6.1.4.1.20044.48.9.4.1.1.6 | Columnpm801rrCfgLastChannelPortn | read-only | current | Number of the last channel of the component :This OID defines the last channel number of the PM |
| 1.3.6.1.4.1.20044.48.9.4.1.1.7 | Columnpm801rrCfgGridPortn | read-only | current | Grid value of the component :This OID defines the grid of the PM |
| 1.3.6.1.4.1.20044.48.9.257 | Scalarpm801rrCfgWriteConfiguration | read-write | current | Write configuration to module:This OID writes the complete configuration to the module |
| 1.3.6.1.4.1.20044.48.10 | Nodepm801rrtraps | |||
| 1.3.6.1.4.1.20044.48.10.4 | Scalarpm801rrtrapBoardNumber | read-only | current | Last module which generates a trap |
| 1.3.6.1.4.1.20044.48.10.30 | Notificationpm801rrLineTrapNotUrgentGoesOn | current | Not urgent Line default is activated | |
| 1.3.6.1.4.1.20044.48.10.31 | Notificationpm801rrLineTrapNotUrgentGoesOff | current | Not urgent Line default disappeared | |
| 1.3.6.1.4.1.20044.48.10.32 | Notificationpm801rrLineTrapUrgentGoesOn | current | Urgent Line default is activated | |
| 1.3.6.1.4.1.20044.48.10.33 | Notificationpm801rrLineTrapUrgentGoesOff | current | Urgent Line default disappeared | |
| 1.3.6.1.4.1.20044.48.10.34 | Notificationpm801rrLineTrapCritGoesOn | current | Critical Line default is activated | |
| 1.3.6.1.4.1.20044.48.10.35 | Notificationpm801rrLineTrapCritGoesOff | current | Critical Line default disappeared | |
| 1.3.6.1.4.1.20044.48.10.40 | Notificationpm801rrClientTrapNotUrgentGoesOn | current | Not urgent client default is activated | |
| 1.3.6.1.4.1.20044.48.10.41 | Notificationpm801rrClientTrapNotUrgentGoesOff | current | Not urgent client default disappeared | |
| 1.3.6.1.4.1.20044.48.10.42 | Notificationpm801rrClientTrapUrgentGoesOn | current | Urgent client default is activated | |
| 1.3.6.1.4.1.20044.48.10.43 | Notificationpm801rrClientTrapUrgentGoesOff | current | Urgent client default disappeared | |
| 1.3.6.1.4.1.20044.48.10.44 | Notificationpm801rrClientTrapCritGoesOn | current | Critical client default is activated | |
| 1.3.6.1.4.1.20044.48.10.45 | Notificationpm801rrClientTrapCritGoesOff | current | Critical client default disappeared | |
| 1.3.6.1.4.1.20044.48.10.50 | Notificationpm801rrPowerTrapUrgentGoesOn | current | Urgent power supply default is activated | |
| 1.3.6.1.4.1.20044.48.10.51 | Notificationpm801rrPowerTrapUrgentGoesOff | current | Urgent power supply default disappeared |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| Pm801rrAdjustValue | INTEGER { otxadjustvalue0(0), otxadjustvalue1(1), otxadjustvalue2(2), otxadjustvalue3(3), otxadjustvalue4(4), otxadjustvalue5(5), otxadjustvalue6(6), otxadjustvalue7(7), otxadjustvalue8(8), otxadjustvalue9(9), otxadjustvalue10(10) } | current | Different values in Adjust mode on OTX-TLH on client and line ports |
| Pm801rrBitRate | INTEGER { rateOC192(0), rate10GBELAN(1), rate10GBEWAN(2), rate10GFC(3), rate10FECG975(4), rate10FECG709(5) } | current | different rates for a client and line ports |
| Pm801rrOtxChannel | INTEGER | current | Channel selection on OTX-TLH on client and line ports |
| Pm801rrOtxGrid | INTEGER { otxgrid200(200), otxgrid100(100), otxgrid50(50) } | current | Different grids on OTX-TLH on client and line ports |
| Pm801rrOtxMode | INTEGER { otx80mode(1), otx60mode(2), otxadjustmode(4) } | current | Different modes on OTX-TLH on client and line ports |