EKINOPS-PmOa-MIB
193 objects
MIB for the Ekinops pmoa hardware.
Imported Objects
| EKINOPS-MIB | EkiApiState EkiMeasureType EkiMode ekinops EkiOnOff EkiProtocol EkiState EkiSynchroMode |
| SNMPv2-SMI | Counter32 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.20044.9 | Identitymodulepmoa | MIB for the Ekinops pmoa hardware. | ||
| 1.3.6.1.4.1.20044.9.2 | Nodepmoaalarms | |||
| 1.3.6.1.4.1.20044.9.2.1 | NodepmoaAlmOther | |||
| 1.3.6.1.4.1.20044.9.2.1.1 | NodepmoaAlmOtherNurg | |||
| 1.3.6.1.4.1.20044.9.2.1.1.2 | NodepmoaAlmsynthAlm2 | |||
| 1.3.6.1.4.1.20044.9.2.1.1.2.1 | ScalarpmoaAlmConfTableSave | read-only | current | PM Configuration Save :This OID is at 1 during the saving of a new configuration table in the module Flash memory. <Condtype> CONF_TABLE_SAVE <Probcause> other… |
| 1.3.6.1.4.1.20044.9.2.1.1.2.2 | ScalarpmoaAlmInvUpload | read-only | current | Inventory Upload :This OID is at 1 during the uploading of PM inventory information. <Condtype> INV_UPLOAD <Probcause> other (1) <Alarmtype> other (1) <Polarit… |
| 1.3.6.1.4.1.20044.9.2.1.1.2.3 | ScalarpmoaAlmConfTableLoad | read-only | current | PM Configuration Load :This OID is at 1 during the loading of configuration tables in the modules RAM. <Condtype> CONF_TABLE_LOAD <Probcause> other (1) <Alarmt… |
| 1.3.6.1.4.1.20044.9.2.1.1.75 | NodepmoaAlmfoaWarnings | |||
| 1.3.6.1.4.1.20044.9.2.1.1.75.5 | ScalarpmoaAlm3v3LowWarning | read-only | current | 3V3 Low Warning :This OID indicates that the PM 3V3 voltage is lower than the Warning threshold <Condtype> 3V3_LOW_WARNING <Probcause> powerProblem (36) <Alarm… |
| 1.3.6.1.4.1.20044.9.2.1.1.75.6 | ScalarpmoaAlm3v3HighWarning | read-only | current | 3V3 High Warning :This OID indicates that the PM 3V3 voltage is higher than the Warning threshold <Condtype> 3V3_HIGH_WARNING <Probcause> powerProblem (36) <Al… |
| 1.3.6.1.4.1.20044.9.2.1.1.75.7 | ScalarpmoaAlmTermpLowWarning | read-only | current | Temperature Low Warning :This OID indicates that the PM temperature if lower than the Warning threshold <Condtype> TERMP_LOW_WARNING <Probcause> temperatureUna… |
| 1.3.6.1.4.1.20044.9.2.1.1.75.8 | ScalarpmoaAlmTempHighWarning | read-only | current | Temperature High Warning :This OID indicates that the PM temperature if higher than the Warning threshold <Condtype> TEMP_HIGH_WARNING <Probcause> temperatureU… |
| 1.3.6.1.4.1.20044.9.2.1.2 | NodepmoaAlmOtherUrg | |||
| 1.3.6.1.4.1.20044.9.2.1.2.74 | NodepmoaAlmfoaAlarms | |||
| 1.3.6.1.4.1.20044.9.2.1.2.74.5 | ScalarpmoaAlm3v3LowAlarm | read-only | current | 3V3 Low Alarm :This OID indicates that the PM 3V3 voltage is lower than the alarm threshold <Condtype> 3V3_LOW_ALARM <Probcause> powerProblem (36) <Alarmtype> … |
| 1.3.6.1.4.1.20044.9.2.1.2.74.6 | ScalarpmoaAlm3v3HighAlarm | read-only | current | 3V3 High Alarm :This OID indicates that the PM 3V3 voltage is higher than the alarm threshold <Condtype> 3V3_HIGH_ALARM <Probcause> powerProblem (36) <Alarmtyp… |
| 1.3.6.1.4.1.20044.9.2.1.2.74.7 | ScalarpmoaAlmTermpLowAlarm | read-only | current | Temperature Low Alarm :This OID indicates that the PM temperature if lower than the alarm threshold <Condtype> TERMP_LOW_ALARM <Probcause> temperatureUnaccepta… |
| 1.3.6.1.4.1.20044.9.2.1.2.74.8 | ScalarpmoaAlmTempHighAlarm | read-only | current | Temperature High Alarm :This OID indicates that the PM temperature is higher than the alarm threshold <Condtype> TEMP_HIGH_ALARM <Probcause> temperatureUnaccep… |
| 1.3.6.1.4.1.20044.9.2.1.3 | NodepmoaAlmOtherCrit | |||
| 1.3.6.1.4.1.20044.9.2.1.3.0 | NodepmoaAlmsynthAlm0 | |||
| 1.3.6.1.4.1.20044.9.2.1.3.0.1 | ScalarpmoaAlmMaintenanceMode | read-only | current | Maintenance Mode :This OID indicates that the PM is in maintenance mode <Help> This status indiates if the module is currently in maintenance mode <Condtype> M… |
| 1.3.6.1.4.1.20044.9.2.1.3.0.9 | ScalarpmoaAlmModGlobFail | read-only | current | Module Failure :This OID is set on detection of a failure originating from the PM <Condtype> MOD_GLOB_FAIL <Probcause> equipmentMalfunction (16) <Alarmtype> sy… |
| 1.3.6.1.4.1.20044.9.2.1.3.0.10 | ScalarpmoaAlmUpEdfaInitNotCompl | read-only | current | Booster Not Initialized :This OID indicates that the initialisation of the Booster is not completed <Help> This status indicates if the Booster has been correc… |
| 1.3.6.1.4.1.20044.9.2.1.3.0.11 | ScalarpmoaAlmDwEdfaInitNotCompl | read-only | current | Pre-Amp Not Initialized :This OID indicates that the initialisation of the Pre-Amp is not completed <Help> This status indicates if the Pre-Amp has been correc… |
| 1.3.6.1.4.1.20044.9.2.1.3.0.12 | ScalarpmoaAlmExtPumpNotLocked | read-only | current | External Pump1 Not Detected :This OID indicates that the first external pump is not detected by the amplifier module <Help> This alarm indicates if the first e… |
| 1.3.6.1.4.1.20044.9.2.1.3.0.15 | ScalarpmoaAlmDefFuseA | read-only | current | Fuse A Fail :This OID indicates that the fuse of the power input A is in fail condition <Help> Status of the Fuse A <Condtype> DEF_FUSE_A <Probcause> powerProb… |
| 1.3.6.1.4.1.20044.9.2.1.3.0.16 | ScalarpmoaAlmDefFuseB | read-only | current | Fuse B Fail :This OID indicates that the fuse of the power input B is in fail condition <Help> Status of the Fuse B <Condtype> DEF_FUSE_B <Probcause> powerProb… |
| 1.3.6.1.4.1.20044.9.2.2 | NodepmoaAlmClient | |||
| 1.3.6.1.4.1.20044.9.2.2.1 | NodepmoaAlmClientNurg | |||
| 1.3.6.1.4.1.20044.9.2.2.1.33 | NodepmoaAlmclientEdfaWarnings | |||
| 1.3.6.1.4.1.20044.9.2.2.1.33.1 | ScalarpmoaAlmClientGainLowWarning | read-only | current | Pre-Amp Gain Low Warning :This OID indicates that the Gain is lower than the Warning theshold of the Pre-Amp Module <Help> This alarm indicates if the Pre-Amp … |
| 1.3.6.1.4.1.20044.9.2.2.1.33.2 | ScalarpmoaAlmClientGainHighWarning | read-only | current | Pre-Amp Gain High Warning :This OID indicates that the Gain is higher than the Warning threshold of the Pre-Amp Module <Help> This alarm indicates if the Pre-A… |
| 1.3.6.1.4.1.20044.9.2.2.1.33.3 | ScalarpmoaAlmClientInputPwrLowWarning | read-only | current | Booster Rx Pwr Low Warning :This OID indicates that the Receive Power is lower than the Warning theshold of the Booster Optical Module <Help> This warning indi… |
| 1.3.6.1.4.1.20044.9.2.2.1.33.4 | ScalarpmoaAlmClientInputPwrHighWarning | read-only | current | Booster Rx Pwr High Warning :This OID indicates that the Receive Power is higher than the Warning theshold of the Booster Optical Module <Help> This warning in… |
| 1.3.6.1.4.1.20044.9.2.2.1.33.5 | ScalarpmoaAlmClientOutputPwrLowWarning | read-only | current | Pre-Amp Tx Pwr Low Warning :This OID indicates that the Transmit Power is lower than the Warning theshold of the Pre-Amp Optical Module <Help> This warning ind… |
| 1.3.6.1.4.1.20044.9.2.2.1.33.6 | ScalarpmoaAlmClientOutputPwrHighWarning | read-only | current | Pre-Amp Tx Pwr High Warning :This OID indicates that the Transmit Power is higher than the Warning theshold of the Pre-Amp Optical Module <Help> This warning i… |
| 1.3.6.1.4.1.20044.9.2.2.1.33.7 | ScalarpmoaAlmClientBiasLowWarning | read-only | current | Pre-Amp Bias Low Warning :This OID indicates that the Bias is lower than the Warning theshold of the Pre-Amp Optical Module <Help> This warning indicates if th… |
| 1.3.6.1.4.1.20044.9.2.2.1.33.8 | ScalarpmoaAlmClientBiasHighWarning | read-only | current | Pre-Amp Bias High Warning :This OID indicates that the Bias is higher than the Warning theshold of the Pre-Amp Optical Module <Help> This warning indicates if … |
| 1.3.6.1.4.1.20044.9.2.2.2 | NodepmoaAlmClientUrg | |||
| 1.3.6.1.4.1.20044.9.2.2.2.32 | NodepmoaAlmclientEdfaAlarms1 | |||
| 1.3.6.1.4.1.20044.9.2.2.2.32.1 | ScalarpmoaAlmClientGainLowAlarm | read-only | current | Pre-Amp Gain Low Alarm :This OID indicates that the Gain is lower than the alarm theshold of the Pre-Amp Module <Help> This alarm indicates if the Pre-Amp gain… |
| 1.3.6.1.4.1.20044.9.2.2.2.32.2 | ScalarpmoaAlmClientGainHighAlarm | read-only | current | Pre-Amp Gain High Alarm :This OID indicates that the Gain is higher than the alarm threshold of the Pre-Amp Module <Help> This alarm indicates if the Pre-Amp g… |
| 1.3.6.1.4.1.20044.9.2.2.2.32.3 | ScalarpmoaAlmClientInputPwrLowAlarm | read-only | current | Booster Rx Pwr Low Alarm :This OID indicates that the Receive Power is lower than the alarm theshold of the Booster Optical Module <Help> This alarm indicates … |
| 1.3.6.1.4.1.20044.9.2.2.2.32.4 | ScalarpmoaAlmClientInputPwrHighAlarm | read-only | current | Booster Rx Pwr High Alarm :This OID indicates that the Receive Power is higher than the alarm theshold of the Booster Optical Module <Help> This alarm indicate… |
| 1.3.6.1.4.1.20044.9.2.2.2.32.5 | ScalarpmoaAlmClientOutputPwrLowAlarm | read-only | current | Pre-Amp Tx Pwr Low Alarm :This OID indicates that the Transmit Power is lower than the alarm theshold of the Pre-Amp Optical Module <Help> This alarm indicates… |
| 1.3.6.1.4.1.20044.9.2.2.2.32.6 | ScalarpmoaAlmClientOutputPwrHighAlarm | read-only | current | Pre-Amp Tx Pwr High Alarm :This OID indicates that the Transmit Power is higher than the alarm theshold of the Pre-Amp Optical Module <Help> This alarm indicat… |
| 1.3.6.1.4.1.20044.9.2.2.2.32.7 | ScalarpmoaAlmClientBiasLowAlarm | read-only | current | Pre-Amp Bias Low Alarm :This OID indicates that the Bias is lower than the alarm theshold of the Pre-Amp Optical Module <Help> This alarm indicates if the Pre-… |
| 1.3.6.1.4.1.20044.9.2.2.2.32.8 | ScalarpmoaAlmClientBiasHighAlarm | read-only | current | Pre-Amp Bias High Alarm :This OID indicates that the Bias is higher than the alarm theshold of the Pre-Amp Optical Module <Help> This alarm indicates if the Pr… |
| 1.3.6.1.4.1.20044.9.2.2.3 | NodepmoaAlmClientCrit | |||
| 1.3.6.1.4.1.20044.9.2.2.3.8 | NodepmoaAlmsynthAlm8 | |||
| 1.3.6.1.4.1.20044.9.2.2.3.8.4 | ScalarpmoaAlmClientHwFail | read-only | current | Client Port HW Failure :This OID indicates a failure on Client port, most probably caused by a HW issue <Condtype> CLIENT_HW_FAIL <Probcause> equipmentMalfunct… |
| 1.3.6.1.4.1.20044.9.2.2.3.8.5 | ScalarpmoaAlmClientTxOff | read-only | current | Pre-Amp Optical Output Shutdown :This OID indicates the Pre-Amp optical output power is on <Help> This status indicates if the Pre-Amp laser pump transceiver l… |
| 1.3.6.1.4.1.20044.9.2.2.3.8.9 | ScalarpmoaAlmClientDdmWarning | read-only | current | Warning On Client Optical Module DDM :This OID indicates a warning is present coming out of Client optical interface DDM <Condtype> CLIENT_DDM_WARNING <Probcau… |
| 1.3.6.1.4.1.20044.9.2.2.3.8.10 | ScalarpmoaAlmClientDdmAlm | read-only | current | Alarm On Client Optical Module DDM :This OID indicates an alarm is present coming out of Client optical interface DDM <Condtype> CLIENT_DDM_ALM <Probcause> equ… |
| 1.3.6.1.4.1.20044.9.2.2.3.8.12 | ScalarpmoaAlmClientFail | read-only | current | Client Port Failure :This OID indicates a failure on the Client port <Condtype> CLIENT_FAIL <Probcause> equipmentMalfunction (16) <Alarmtype> synthesisAlarm (1… |
| 1.3.6.1.4.1.20044.9.2.2.3.35 | NodepmoaAlmclientEdfaAlarms2 | |||
| 1.3.6.1.4.1.20044.9.2.2.3.35.1 | ScalarpmoaAlmClientEdfaNr | read-only | current | Pre-Amp Optical Module Not Ready :This OID indicates that the Pre-Amp Optical Module is not ready <Help> This status indicates if the Pre-Amp has been correctl… |
| 1.3.6.1.4.1.20044.9.2.2.3.35.2 | ScalarpmoaAlmClientEdfaTecFail | read-only | current | Pre-Amp TEC Fail :This OID indicates that the TEC is in fail condition on the Pre-Amp Optical Module <Help> This alarm indicates if the TEC of the Pre-Amp is i… |
| 1.3.6.1.4.1.20044.9.2.2.3.35.3 | ScalarpmoaAlmClientEdfaLaserFail | read-only | current | Pre-Amp Pump Laser Fail :This OID indicates a Transmit Laser Fail on the Pre-Amp Optical Module <Help> This alarm indicates if the laser of the Pre-Amp is in f… |
| 1.3.6.1.4.1.20044.9.2.2.3.35.4 | ScalarpmoaAlmClientEdfaLos | read-only | current | Booster Loss Of Signal :This OID indicates a Loss of Signal on the Booster Optical Module <Help> This alarm indicates if an optical signal is detected on the B… |
| 1.3.6.1.4.1.20044.9.2.2.3.35.5 | ScalarpmoaAlmClientExtPumpEdfaLowCurrent | read-only | current | Pre-Amp External Pump1 Low Current :This OID indicates that the EDFA pump current of the first external pump linked to the Pre-Amp is too low <Help> This alarm… |
| 1.3.6.1.4.1.20044.9.2.3 | NodepmoaAlmLine | |||
| 1.3.6.1.4.1.20044.9.2.3.1 | NodepmoaAlmLineNurg | |||
| 1.3.6.1.4.1.20044.9.2.3.1.41 | NodepmoaAlmlineEdfaWarnings | |||
| 1.3.6.1.4.1.20044.9.2.3.1.41.1 | ScalarpmoaAlmLineGainLowWarning | read-only | current | Booster Gain Low Warning :This OID indicates that the Gain is lower than the Warning theshold of the Booster Module <Help> This alarm indicates if the Booster … |
| 1.3.6.1.4.1.20044.9.2.3.1.41.2 | ScalarpmoaAlmLineGainHighWarning | read-only | current | Booster Gain High Warning :This OID indicates that the Gain is higher than the Warning threshold of the Booster Module <Help> This alarm indicates if the Boost… |
| 1.3.6.1.4.1.20044.9.2.3.1.41.3 | ScalarpmoaAlmLineInputPwrLowWarning | read-only | current | Pre-Amp Rx Pwr Low Warning :This OID indicates that the Receive Power is lower than the Warning theshold of the Pre-Amp Optical Module <Help> This warning indi… |
| 1.3.6.1.4.1.20044.9.2.3.1.41.4 | ScalarpmoaAlmLineInputPwrHighWarning | read-only | current | Pre-Amp Rx Pwr High Warning :This OID indicates that the Receive Power is higher than the Warning theshold of the Pre-Amp Optical Module <Help> This warning in… |
| 1.3.6.1.4.1.20044.9.2.3.1.41.5 | ScalarpmoaAlmLineOutputPwrLowWarning | read-only | current | Booster Tx Pwr Low Warning :This OID indicates that the Transmit Power is lower than the Warning theshold of the Booster Optical Module <Help> This warning ind… |
| 1.3.6.1.4.1.20044.9.2.3.1.41.6 | ScalarpmoaAlmLineOutputPwrHighWarning | read-only | current | Booster Tx Pwr High Warning :This OID indicates that the Transmit Power is higher than the Warning theshold of the Booster Optical Module <Help> This warning i… |
| 1.3.6.1.4.1.20044.9.2.3.1.41.7 | ScalarpmoaAlmLineBiasLowWarning | read-only | current | Booster Bias Low Warning :This OID indicates that the Bias is lower than the Warning theshold of the Booster Optical Module <Help> This warning indicates if th… |
| 1.3.6.1.4.1.20044.9.2.3.1.41.8 | ScalarpmoaAlmLineBiasHighWarning | read-only | current | Booster Bias High Warning :This OID indicates that the Bias is higher than the Warning theshold of the Booster Optical Module <Help> This warning indicates if … |
| 1.3.6.1.4.1.20044.9.2.3.2 | NodepmoaAlmLineUrg | |||
| 1.3.6.1.4.1.20044.9.2.3.2.40 | NodepmoaAlmlineEdfaAlarms1 | |||
| 1.3.6.1.4.1.20044.9.2.3.2.40.1 | ScalarpmoaAlmLineGainLowAlarm | read-only | current | Booster Gain Low Alarm :This OID indicates that the Gain is lower than the alarm theshold of the Booster Module <Help> This alarm indicates if the Booster gain… |
| 1.3.6.1.4.1.20044.9.2.3.2.40.2 | ScalarpmoaAlmLineGainHighAlarm | read-only | current | Booster Gain High Alarm :This OID indicates that the Gain is higher than the alarm threshold of the Booster Module <Help> This alarm indicates if the Booster g… |
| 1.3.6.1.4.1.20044.9.2.3.2.40.3 | ScalarpmoaAlmLineInputPwrLowAlarm | read-only | current | Pre-Amp Rx Pwr Low Alarm :This OID indicates that the Receive Power is lower than the alarm theshold of the Pre-Amp Optical Module <Help> This alarm indicates … |
| 1.3.6.1.4.1.20044.9.2.3.2.40.4 | ScalarpmoaAlmLineInputPwrHighAlarm | read-only | current | Pre-Amp Rx Pwr High Alarm :This OID indicates that the Receive Power is higher than the alarm theshold of the Pre-Amp Optical Module <Help> This alarm indicate… |
| 1.3.6.1.4.1.20044.9.2.3.2.40.5 | ScalarpmoaAlmLineOutputPwrLowAlarm | read-only | current | Booster Tx Pwr Low Alarm :This OID indicates that the Transmit Power is lower than the alarm theshold of the Booster Optical Module <Help> This alarm indicates… |
| 1.3.6.1.4.1.20044.9.2.3.2.40.6 | ScalarpmoaAlmLineOutputPwrHighAlarm | read-only | current | Booster Tx Pwr High Alarm :This OID indicates that the Transmit Power is higher than the alarm theshold of the Booster Optical Module <Help> This alarm indicat… |
| 1.3.6.1.4.1.20044.9.2.3.2.40.7 | ScalarpmoaAlmLineBiasLowAlarm | read-only | current | Booster Bias Low Alarm :This OID indicates that the Bias is lower than the alarm theshold of the Booster Optical Module <Help> This alarm indicates if the Boos… |
| 1.3.6.1.4.1.20044.9.2.3.2.40.8 | ScalarpmoaAlmLineBiasHighAlarm | read-only | current | Booster Bias High Alarm :This OID indicates that the Bias is higher than the alarm theshold of the Booster Optical Module <Help> This alarm indicates if the Bo… |
| 1.3.6.1.4.1.20044.9.2.3.3 | NodepmoaAlmLineCrit | |||
| 1.3.6.1.4.1.20044.9.2.3.3.7 | NodepmoaAlmsynthAlm7 | |||
| 1.3.6.1.4.1.20044.9.2.3.3.7.4 | ScalarpmoaAlmLineHwFail | read-only | current | Line Port HW Failure :This OID indicates a failure on line port, most probably caused by a HW issue <Condtype> LINE_HW_FAIL <Probcause> equipmentMalfunction (1… |
| 1.3.6.1.4.1.20044.9.2.3.3.7.5 | ScalarpmoaAlmLineTxOff | read-only | current | Booster Optical Output Shutdown :This OID indicates the Booster optical output power is on <Help> This status indicates if the Booster laser pump is ON or OFF … |
| 1.3.6.1.4.1.20044.9.2.3.3.7.9 | ScalarpmoaAlmLineDdmWarning | read-only | current | Warning On Line Optical Module DDM :This OID indicates a warning is present coming out of Line optical interface DDM <Condtype> LINE_DDM_WARNING <Probcause> eq… |
| 1.3.6.1.4.1.20044.9.2.3.3.7.10 | ScalarpmoaAlmLineDdmAlm | read-only | current | Alarm On Line Optical Module DDM :This OID indicates an alarm is present coming out of Line optical interface DDM <Condtype> LINE_DDM_ALM <Probcause> equipment… |
| 1.3.6.1.4.1.20044.9.2.3.3.7.12 | ScalarpmoaAlmLineFail | read-only | current | Line Port Failure :This OID indicates a failure on the line port <Condtype> LINE_FAIL <Probcause> equipmentMalfunction (16) <Alarmtype> synthesisAlarm (12) <Po… |
| 1.3.6.1.4.1.20044.9.2.3.3.43 | NodepmoaAlmlineEdfaAlarms2 | |||
| 1.3.6.1.4.1.20044.9.2.3.3.43.1 | ScalarpmoaAlmLineEdfaNr | read-only | current | Booster Optical Module Not Ready :This OID indicates that the Booster Optical Module is not ready <Help> This status indicates if the Booster has been correctl… |
| 1.3.6.1.4.1.20044.9.2.3.3.43.2 | ScalarpmoaAlmLineEdfaTecFail | read-only | current | Booster TEC Fail :This OID indicates that the TEC is in fail condition on the Booster Optical Module <Help> This alarm indicates if the TEC of the Booster is i… |
| 1.3.6.1.4.1.20044.9.2.3.3.43.3 | ScalarpmoaAlmLineEdfaLaserFail | read-only | current | Booster Pump Laser Fail :This OID indicates a Transmit Laser Fail on the Booster Optical Module <Help> This alarm indicates if the laser of the Booster is in f… |
| 1.3.6.1.4.1.20044.9.2.3.3.43.4 | ScalarpmoaAlmLineEdfaLos | read-only | current | Pre-Amp Loss Of Signal :This OID indicates a Loss of Signal on the Pre-Amp Optical Module <Help> This alarm indicates if an optical signal is detected on the P… |
| 1.3.6.1.4.1.20044.9.2.3.3.43.5 | ScalarpmoaAlmLineExtPumpEdfaLowCurrent | read-only | current | Booster External Pump1 Low Current :This OID indicates that the EDFA pump current of the first external pump linked to the Booster is too low <Help> This alarm… |
| 1.3.6.1.4.1.20044.9.3 | Nodepmoameasures | |||
| 1.3.6.1.4.1.20044.9.3.1 | NodepmoaMesrOther | |||
| 1.3.6.1.4.1.20044.9.3.1.72 | ScalarpmoaMesrtempMeas | read-only | current | Module Temperature :This OID gives the temperature of the PM (Temperature =AV/256) (Unit = C) <Help> This measure gives the temperature of the module |
| 1.3.6.1.4.1.20044.9.3.1.73 | ScalarpmoaMesr3v3Meas | read-only | current | Module 3.3 Voltage :This OID gives the 3V3 voltage of the PM (Voltage =AV/10000) (Unit = V) <Help> This measure gives the 3V3 voltage of the module |
| 1.3.6.1.4.1.20044.9.3.2 | NodepmoaMesrClient | |||
| 1.3.6.1.4.1.20044.9.3.2.32 | ScalarpmoaMesrclientEdfaBiasMeas | read-only | current | Pre-Amp Pump Laser Current :This OID gives the pump laser current of the Pre-Amp Optical Module (Current =AV/100) (Unit = mA) <Help> This measure gives the bia… |
| 1.3.6.1.4.1.20044.9.3.2.33 | ScalarpmoaMesrclientEdfaTxpwrMeas | read-only | current | Pre-Amp Tx Power :This OID gives the transmit power value of the Pre-Amp Optical Module (Power =(AV-32768)*0,005) (Unit = dBm) <Help> This measure gives the Tx… |
| 1.3.6.1.4.1.20044.9.3.2.34 | ScalarpmoaMesrclientEdfaRxpwrMeas | read-only | current | Booster Rx Power :This OID gives the receive power value of the Booster Optical Module (Power =(AV-32768)*0,005) (Unit = dBm) <Help> This measure gives the Rx … |
| 1.3.6.1.4.1.20044.9.3.2.35 | ScalarpmoaMesrclientEdfaGainMeas | read-only | current | Pre-Amp Gain :This OID gives the gain value of the Pre-Amp Module (Gain =(AV-32768)*0,005) (Unit = dB) <Help> This measure gives the optical gain of the Pre-Amp |
| 1.3.6.1.4.1.20044.9.3.3 | NodepmoaMesrLine | |||
| 1.3.6.1.4.1.20044.9.3.3.40 | ScalarpmoaMesrlineEdfaBiasMeas | read-only | current | Booster Pump Laser Current :This OID gives the pump laser current of the Booster Optical Module (Current =AV/100) (Unit = mA) <Help> This measure gives the bia… |
| 1.3.6.1.4.1.20044.9.3.3.41 | ScalarpmoaMesrlineEdfaTxpwrMeas | read-only | current | Booster Tx Power :This OID gives the transmit power value of the Booster Optical Module (Power =(AV-32768)*0,005) (Unit = dBm) <Help> This measure gives the Tx… |
| 1.3.6.1.4.1.20044.9.3.3.42 | ScalarpmoaMesrlineEdfaRxpwrMeas | read-only | current | Pre-Amp Rx Power :This OID gives the receive power value of the Pre-Amp Optical Module (Power =(AV-32768)*0,005) (Unit = dBm) <Help> This measure gives the Rx … |
| 1.3.6.1.4.1.20044.9.3.3.43 | ScalarpmoaMesrlineEdfaGainMeas | read-only | current | Booster Gain :This OID gives the gain value of the Booster Module (Gain =(AV-32768)*0,005) (Unit = dB) <Help> This measure gives the optical gain of the Booster |
| 1.3.6.1.4.1.20044.9.6 | NodepmoacontrolsWrite | |||
| 1.3.6.1.4.1.20044.9.6.1 | NodepmoaCtrlOther | |||
| 1.3.6.1.4.1.20044.9.6.1.0 | NodepmoaCtrlsynth0 | |||
| 1.3.6.1.4.1.20044.9.6.1.0.1 | ScalarpmoaCtrlConfLoad | read-write | current | Load Configuration Tables :When set this enables loading from flash configuration1 into the module. |
| 1.3.6.1.4.1.20044.9.6.1.0.9 | ScalarpmoaCtrlConfFlash | read-write | current | Write Configuration Tables :This bit saves the current configuration of the module as configuration in the flash. <Help> This control saves the customer config… |
| 1.3.6.1.4.1.20044.9.6.1.0.13 | ScalarpmoaCtrlConfClear | read-write | current | Clear Configuration Tables :This bit clears the configuration tables from configuration in the flash. <Help> This control restores the default configuration of… |
| 1.3.6.1.4.1.20044.9.6.1.5 | NodepmoaCtrlswMgnt | |||
| 1.3.6.1.4.1.20044.9.6.1.5.2 | ScalarpmoaCtrlColdReset | read-write | current | PM Cold Reset :This OID, when set, causes a cold reset of the Software. This reset is traffic affecting, and the configuration of Software is reloaded on start… |
| 1.3.6.1.4.1.20044.9.6.1.5.3 | ScalarpmoaCtrlWarmReset | read-write | current | PM Warm Reset :This OID, when set, causes a warm reset of the Software. This reset is not traffic affecting, and the configuration of the Sofwtare remains unch… |
| 1.3.6.1.4.1.20044.9.6.1.72 | NodepmoaCtrlpowerDown | |||
| 1.3.6.1.4.1.20044.9.6.1.72.1 | ScalarpmoaCtrlSoftPowerDown | read-write | current | Module Software Shutdown :This OID shuts down the PM Software <Help> This control initiates a shut down of software. |
| 1.3.6.1.4.1.20044.9.6.1.73 | NodepmoaCtrlledTest | |||
| 1.3.6.1.4.1.20044.9.6.1.73.1 | ScalarpmoaCtrlGreenLed | read-write | current | Green Leds Test :This OID switches on all the green Leds as a test feature. <Help> This control initiates a test leds turning all the LEDs to green |
| 1.3.6.1.4.1.20044.9.6.1.73.2 | ScalarpmoaCtrlRedLed | read-write | current | Red Leds Test :This OID switches on all the red Leds as a test feature. <Help> This control initiates a test leds turning all the LEDs to red |
| 1.3.6.1.4.1.20044.9.6.1.73.3 | ScalarpmoaCtrlLedOff | read-write | current | Leds Off :This OID switches off all the Leds as a test feature. <Help> This control initiates a test leds turning all the LEDs to OFF |
| 1.3.6.1.4.1.20044.9.6.1.75 | NodepmoaCtrlmaintMode | |||
| 1.3.6.1.4.1.20044.9.6.1.75.1 | ScalarpmoaCtrlMaintenance | read-write | current | Module Maintenance Mode :This OID sets the PM in maintenance mode <Help> This control enables the maintenance mode of the module |
| 1.3.6.1.4.1.20044.9.6.2 | NodepmoaCtrlClient | |||
| 1.3.6.1.4.1.20044.9.6.2.32 | NodepmoaCtrlclientEdfaLaserOff | |||
| 1.3.6.1.4.1.20044.9.6.2.32.1 | ScalarpmoaCtrlClientEdfaLaserOff | read-write | current | Pre-Amp Pump Laser Shutdown :This OID switches OFF the laser of the Pre-Amp Optical Module <Help> This control defines the laser state of the Pre-Amp |
| 1.3.6.1.4.1.20044.9.6.2.33 | ScalarpmoaCtrlclientEdfaMode | read-write | current | Pre-Amp Module Mode :This OID selects the mode of the Pre-Amp Module <Help> This control defines the Pre-Amp Mode (0: Default mode, 2:Constant output power) |
| 1.3.6.1.4.1.20044.9.6.2.34 | ScalarpmoaCtrlclientIlasSettingValue | read-write | current | Pre-Amp Laser Current Value :This OID sets the value of the laser current of the Pre-Amp Module (active only in constant current mode) (AV = Current *100) (Uni… |
| 1.3.6.1.4.1.20044.9.6.2.35 | ScalarpmoaCtrlclientPlasSettingValue | read-write | current | Pre-Amp Pump Power Value :This OID sets the value of the laser power of the Pre-Amp Optical Module (active only in constant power mode) (AV=(Power/0,005) + 327… |
| 1.3.6.1.4.1.20044.9.6.2.36 | ScalarpmoaCtrlclientGainSettingValue | read-write | current | Pre-Amp Gain Value :This OID sets the value of the gain of the Pre-Amp Module (active only in constant gain mode) (AV=(Gain/0,005) + 32768) (Unit = dB) |
| 1.3.6.1.4.1.20044.9.6.2.37 | ScalarpmoaCtrlclientEffPwrOutSettingValue | read-write | current | Pre-Amp Effective Output Power :This OID sets the value of the effective output power (without noise power) of the Pre-Amp Module (active only in input power f… |
| 1.3.6.1.4.1.20044.9.6.3 | NodepmoaCtrlLine | |||
| 1.3.6.1.4.1.20044.9.6.3.40 | NodepmoaCtrllineEdfaLaserOff | |||
| 1.3.6.1.4.1.20044.9.6.3.40.1 | ScalarpmoaCtrlLineEdfaLaserOff | read-write | current | Booster Pump Laser Shutdown :This OID switches OFF the laser of the Booster Optical Module <Help> This control defines the laser state of the Booster |
| 1.3.6.1.4.1.20044.9.6.3.41 | ScalarpmoaCtrllineEdfaMode | read-write | current | Booster Module Mode :This OID selects the mode of the Booster Module <Help> This control defines the Booster Mode (0: Default mode, 2:Constant output power) |
| 1.3.6.1.4.1.20044.9.6.3.42 | ScalarpmoaCtrllineIlasSettingValue | read-write | current | Booster Laser Current Value :This OID sets the value of the laser current of the Booster Module (active only in constant current mode) (AV = Current *100) (Uni… |
| 1.3.6.1.4.1.20044.9.6.3.43 | ScalarpmoaCtrllinePlasSettingValue | read-write | current | Booster Pump Power Value :This OID sets the value of the laser power of the Booster Optical Module (active only in constant power mode) (AV=(Power/0,005) + 327… |
| 1.3.6.1.4.1.20044.9.6.3.44 | ScalarpmoaCtrllineGainSettingValue | read-write | current | Booster Gain Value :This OID sets the value of the gain of the Booster Module (active only in constant gain mode) (AV=(Gain/0,005) + 32768) (Unit = dB) |
| 1.3.6.1.4.1.20044.9.6.3.45 | ScalarpmoaCtrllineEffPwrOutSettingValue | read-write | current | Booster Effective Output Power :This OID sets the value of the effective output power (without noise power) of the Booster Module (active only in input power f… |
| 1.3.6.1.4.1.20044.9.7 | Nodepmoari | |||
| 1.3.6.1.4.1.20044.9.7.2 | ScalarpmoaRinvReloadInventory | read-write | current | Reload the inventory: This OID triggers an inventory reload. |
| 1.3.6.1.4.1.20044.9.7.3 | ScalarpmoaRinvModulePlatform | read-only | current | Module platform description: This OID contains the description of the Module. |
| 1.3.6.1.4.1.20044.9.7.4 | ScalarpmoaRinvSwPlatform | read-only | current | SW platform description: This OID contains the description of the Software platform. |
| 1.3.6.1.4.1.20044.9.7.5 | ScalarpmoaRinvSwFoa | read-only | current | Optical device driver description: This OID contains the description of the driver of the optical devices (Booster and Pre-Amp) |
| 1.3.6.1.4.1.20044.9.7.6 | TablepmoaRinvBoosterTable | not-accessible | current | List of the Boosters on the selected module |
| 1.3.6.1.4.1.20044.9.7.6.1 | RowpmoaRinvBoosterEntry | not-accessible | current | Row definition for the Boosters table |
| 1.3.6.1.4.1.20044.9.7.6.1.1 | ColumnpmoaRinvBoosterIndex | read-only | current | Index for Booster table |
| 1.3.6.1.4.1.20044.9.7.6.1.2 | ColumnpmoaRinvBooster | read-only | current | Inventory for the Booster: This OID contains the inventory for the Booster |
| 1.3.6.1.4.1.20044.9.7.7 | TablepmoaRinvPreAmpTable | not-accessible | current | List of the PreAmps on the selected module |
| 1.3.6.1.4.1.20044.9.7.7.1 | RowpmoaRinvPreAmpEntry | not-accessible | current | Row definition for the PreAmp table |
| 1.3.6.1.4.1.20044.9.7.7.1.1 | ColumnpmoaRinvPreAmpIndex | read-only | current | Index for PreAmp table |
| 1.3.6.1.4.1.20044.9.7.7.1.2 | ColumnpmoaRinvPreAmp | read-only | current | Inventory for the PreAmp: This OID contains the inventory for the PreAmp |
| 1.3.6.1.4.1.20044.9.9 | NodepmoaConfig | |||
| 1.3.6.1.4.1.20044.9.9.1 | NodepmoaCfgNoValue | |||
| 1.3.6.1.4.1.20044.9.9.1.1 | NodepmoatableclientStartup | |||
| 1.3.6.1.4.1.20044.9.9.1.1.2 | ScalarpmoaCfgclientEdfaLaserCtrl | read-write | current | Default Settings on Client Laser :This OID configures the default initialisation settings on the client laser. |
| 1.3.6.1.4.1.20044.9.9.1.1.3 | ScalarpmoaCfgclientEdfaLaserMode | read-write | current | Default Settings on Client mode :This OID configures the default mode on the client amplifier. |
| 1.3.6.1.4.1.20044.9.9.2 | NodepmoaCfgLineStartUp | |||
| 1.3.6.1.4.1.20044.9.9.2.1 | NodepmoatablelineStartup | |||
| 1.3.6.1.4.1.20044.9.9.2.1.2 | ScalarpmoaCfglineEdfaLaserCtrl | read-write | current | Default Settings on Line Laser :This OID configures the default initialisation settings on the line laser. |
| 1.3.6.1.4.1.20044.9.9.2.1.3 | ScalarpmoaCfglineEdfaLaserMode | read-write | current | Default Settings on Line mode :This OID configures the default mode on the line amplifier. |
| 1.3.6.1.4.1.20044.9.9.3 | NodepmoaCfgLabels | |||
| 1.3.6.1.4.1.20044.9.9.3.1 | TablepmoaCfgLabelclientTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.9.9.3.1.1 | RowpmoaCfgLabelclientEntry | not-accessible | current | Row definition for the labels table |
| 1.3.6.1.4.1.20044.9.9.3.1.1.1 | ColumnpmoaCfgLabelclientIndex | read-only | current | Index definition for the labelclient table |
| 1.3.6.1.4.1.20044.9.9.3.1.1.3 | ColumnpmoaCfgLabelclientPortn | read-write | current | Default settings on the label of the Ports :These registers configures the default initialisation settings of the labels of the ports. |
| 1.3.6.1.4.1.20044.9.9.3.2 | TablepmoaCfgLabellineTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.9.9.3.2.1 | RowpmoaCfgLabellineEntry | not-accessible | current | Row definition for the labels table |
| 1.3.6.1.4.1.20044.9.9.3.2.1.1 | ColumnpmoaCfgLabellineIndex | read-only | current | Index definition for the labelline table |
| 1.3.6.1.4.1.20044.9.9.3.2.1.3 | ColumnpmoaCfgLabellinePortn | read-write | current | Default settings on the label of the lines :These registers configures the default initialisation settings of the labels of the lines. |
| 1.3.6.1.4.1.20044.9.9.257 | ScalarpmoaCfgWriteConfiguration | read-write | current | Write configuration to module:This OID writes the complete configuration to the module |
| 1.3.6.1.4.1.20044.9.10 | Nodepmoatraps | |||
| 1.3.6.1.4.1.20044.9.10.4 | ScalarpmoatrapBoardNumber | read-only | current | Last module which generates a trap |
| 1.3.6.1.4.1.20044.9.10.30 | NotificationpmoaLineTrapNotUrgentGoesOn | current | Not urgent Line default is activated | |
| 1.3.6.1.4.1.20044.9.10.31 | NotificationpmoaLineTrapNotUrgentGoesOff | current | Not urgent Line default disappeared | |
| 1.3.6.1.4.1.20044.9.10.32 | NotificationpmoaLineTrapUrgentGoesOn | current | Urgent Line default is activated | |
| 1.3.6.1.4.1.20044.9.10.33 | NotificationpmoaLineTrapUrgentGoesOff | current | Urgent Line default disappeared | |
| 1.3.6.1.4.1.20044.9.10.34 | NotificationpmoaLineTrapCritGoesOn | current | Critical Line default is activated | |
| 1.3.6.1.4.1.20044.9.10.35 | NotificationpmoaLineTrapCritGoesOff | current | Critical Line default disappeared | |
| 1.3.6.1.4.1.20044.9.10.40 | NotificationpmoaClientTrapNotUrgentGoesOn | current | Not urgent client default is activated | |
| 1.3.6.1.4.1.20044.9.10.41 | NotificationpmoaClientTrapNotUrgentGoesOff | current | Not urgent client default disappeared | |
| 1.3.6.1.4.1.20044.9.10.42 | NotificationpmoaClientTrapUrgentGoesOn | current | Urgent client default is activated | |
| 1.3.6.1.4.1.20044.9.10.43 | NotificationpmoaClientTrapUrgentGoesOff | current | Urgent client default disappeared | |
| 1.3.6.1.4.1.20044.9.10.44 | NotificationpmoaClientTrapCritGoesOn | current | Critical client default is activated | |
| 1.3.6.1.4.1.20044.9.10.45 | NotificationpmoaClientTrapCritGoesOff | current | Critical client default disappeared | |
| 1.3.6.1.4.1.20044.9.10.50 | NotificationpmoaPowerTrapUrgentGoesOn | current | Urgent power supply default is activated | |
| 1.3.6.1.4.1.20044.9.10.51 | NotificationpmoaPowerTrapUrgentGoesOff | current | Urgent power supply default disappeared |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| PmoaboosterMode | INTEGER { oaboosterdefaultmode(0), oaboosterconstantcurrentmode(1), oaboosterconstantpowermode(2) } | current | Different modes on OA booster |
| PmoapreampMode | INTEGER { oapreampdefaultmode(0), oapreampconstantcurrentmode(1), oapreampconstantpowermode(2) } | current | Different modes on OA preamp |