EKINOPS-PmOabphc-MIB
214 objects
Creation
Imported Objects
| EKINOPS-MIB | EkiApiState EkiMeasureType EkiMode ekinops EkiOnOff EkiProtocol EkiState EkiSynchroMode |
| SNMPv2-SMI | Counter32 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.20044.51 | Identitymodulepmoabphc | Creation | ||
| 1.3.6.1.4.1.20044.51.2 | Nodepmoabphcalarms | |||
| 1.3.6.1.4.1.20044.51.2.1 | NodepmoabphcAlmOther | |||
| 1.3.6.1.4.1.20044.51.2.1.1 | NodepmoabphcAlmOtherNurg | |||
| 1.3.6.1.4.1.20044.51.2.1.1.2 | NodepmoabphcAlmsynthAlm2 | |||
| 1.3.6.1.4.1.20044.51.2.1.1.2.1 | ScalarpmoabphcAlmConfTableSave | read-only | current | PM Configuration Save :This OID is at 1 during the saving of a new configuration table in the module Flash memory. <Condtype> CONF_TABLE_SAVE <Probcause> bandw… |
| 1.3.6.1.4.1.20044.51.2.1.1.2.2 | ScalarpmoabphcAlmInvUpload | read-only | current | Inventory Upload :This OID is at 1 during the uploading of PM inventory information. <Condtype> INV_UPLOAD <Probcause> bandwidthReduced(4) <Alarmtype> other (1… |
| 1.3.6.1.4.1.20044.51.2.1.1.2.3 | ScalarpmoabphcAlmConfTableLoad | read-only | current | PM Configuration Load :This OID is at 1 during the loading of configuration tables in the modules RAM. <Condtype> CONF_TABLE_LOAD <Probcause> bandwidthReduced(… |
| 1.3.6.1.4.1.20044.51.2.1.1.75 | NodepmoabphcAlmfoaWarnings | |||
| 1.3.6.1.4.1.20044.51.2.1.1.75.7 | ScalarpmoabphcAlmTermpLowWarning | read-only | current | Temperature Low Warning :This OID indicates that the PM temperature if lower than the Warning threshold <Condtype> TERMP_LOW_WARNING <Probcause> temperatureUna… |
| 1.3.6.1.4.1.20044.51.2.1.1.75.8 | ScalarpmoabphcAlmTempHighWarning | read-only | current | Temperature High Warning :This OID indicates that the PM temperature if higher than the Warning threshold <Condtype> TEMP_HIGH_WARNING <Probcause> temperatureU… |
| 1.3.6.1.4.1.20044.51.2.1.2 | NodepmoabphcAlmOtherUrg | |||
| 1.3.6.1.4.1.20044.51.2.1.2.74 | NodepmoabphcAlmfoaAlarms | |||
| 1.3.6.1.4.1.20044.51.2.1.2.74.7 | ScalarpmoabphcAlmTermpLowAlarm | read-only | current | Temperature Low Alarm :This OID indicates that the PM temperature if lower than the alarm threshold <Condtype> TERMP_LOW_ALARM <Probcause> temperatureUnaccepta… |
| 1.3.6.1.4.1.20044.51.2.1.2.74.8 | ScalarpmoabphcAlmTempHighAlarm | read-only | current | Temperature High Alarm :This OID indicates that the PM temperature is higher than the alarm threshold <Condtype> TEMP_HIGH_ALARM <Probcause> temperatureUnaccep… |
| 1.3.6.1.4.1.20044.51.2.1.3 | NodepmoabphcAlmOtherCrit | |||
| 1.3.6.1.4.1.20044.51.2.1.3.0 | NodepmoabphcAlmsynthAlm0 | |||
| 1.3.6.1.4.1.20044.51.2.1.3.0.1 | ScalarpmoabphcAlmMaintenanceMode | read-only | current | Maintenance Mode :This OID indicates that the PM is in maintenance mode <Help> This status indiates if the module is currently in maintenance mode <Condtype> M… |
| 1.3.6.1.4.1.20044.51.2.1.3.0.2 | ScalarpmoabphcAlmAprOn | read-only | current | Automatic Power Reduction :This OID indicates that the APR algorithm has been operated and the output of the lasers are shutdown <Help> The APR algorithm has b… |
| 1.3.6.1.4.1.20044.51.2.1.3.0.9 | ScalarpmoabphcAlmModGlobFail | read-only | current | Module Failure :This OID is set on detection of a failure originating from the PM <Condtype> MOD_GLOB_FAIL <Probcause> equipmentMalfunction (16) <Alarmtype> sy… |
| 1.3.6.1.4.1.20044.51.2.1.3.0.10 | ScalarpmoabphcAlmUpEdfaInitNotCompl | read-only | current | Booster Not Initialized :This OID indicates that the initialisation of the Booster is not completed <Help> This status indicates if the Booster has been correc… |
| 1.3.6.1.4.1.20044.51.2.1.3.0.11 | ScalarpmoabphcAlmDwEdfaInitNotCompl | read-only | current | Pre-Amp Not Initialized :This OID indicates that the initialisation of the Pre-Amp is not completed <Help> This status indicates if the Pre-Amp has been correc… |
| 1.3.6.1.4.1.20044.51.2.1.3.0.12 | ScalarpmoabphcAlmExtPump1NotLocked | read-only | current | External Pump1 Not Detected :This OID indicates that the first external pump is not detected by the amplifier module <Help> This alarm indicates if the first e… |
| 1.3.6.1.4.1.20044.51.2.1.3.0.13 | ScalarpmoabphcAlmExtPump2NotLocked | read-only | current | External Pump2 Not Detected :This OID indicates that the second external pump is not detected by the amplifier module <Help> This alarm indicates if the second… |
| 1.3.6.1.4.1.20044.51.2.1.3.0.15 | ScalarpmoabphcAlmDefFuseA | read-only | current | Fuse A Fail :This OID indicates that the fuse of the power input A is in fail condition <Help> Status of the Fuse A <Condtype> DEF_FUSE_A <Probcause> powerProb… |
| 1.3.6.1.4.1.20044.51.2.1.3.0.16 | ScalarpmoabphcAlmDefFuseB | read-only | current | Fuse B Fail :This OID indicates that the fuse of the power input B is in fail condition <Help> Status of the Fuse B <Condtype> DEF_FUSE_B <Probcause> powerProb… |
| 1.3.6.1.4.1.20044.51.2.2 | NodepmoabphcAlmClient | |||
| 1.3.6.1.4.1.20044.51.2.2.1 | NodepmoabphcAlmClientNurg | |||
| 1.3.6.1.4.1.20044.51.2.2.1.33 | NodepmoabphcAlmclientEdfaWarnings | |||
| 1.3.6.1.4.1.20044.51.2.2.1.33.1 | ScalarpmoabphcAlmClientGainLowWarning | read-only | current | Pre-Amp Gain Low Warning :This OID indicates that the Gain is lower than the Warning theshold of the Pre-Amp Module <Help> This alarm indicates if the Pre-Amp … |
| 1.3.6.1.4.1.20044.51.2.2.1.33.2 | ScalarpmoabphcAlmClientGainHighWarning | read-only | current | Pre-Amp Gain High Warning :This OID indicates that the Gain is higher than the Warning threshold of the Pre-Amp Module <Help> This alarm indicates if the Pre-A… |
| 1.3.6.1.4.1.20044.51.2.2.1.33.3 | ScalarpmoabphcAlmClientInputPwrLowWarning | read-only | current | Booster Rx Pwr Low Warning :This OID indicates that the Receive Power is lower than the Warning theshold of the Booster Optical Module <Help> This warning indi… |
| 1.3.6.1.4.1.20044.51.2.2.1.33.4 | ScalarpmoabphcAlmClientInputPwrHighWarning | read-only | current | Booster Rx Pwr High Warning :This OID indicates that the Receive Power is higher than the Warning theshold of the Booster Optical Module <Help> This warning in… |
| 1.3.6.1.4.1.20044.51.2.2.1.33.5 | ScalarpmoabphcAlmClientOutputPwrLowWarning | read-only | current | Pre-Amp Tx Pwr Low Warning :This OID indicates that the Transmit Power is lower than the Warning theshold of the Pre-Amp Optical Module <Help> This warning ind… |
| 1.3.6.1.4.1.20044.51.2.2.1.33.6 | ScalarpmoabphcAlmClientOutputPwrHighWarning | read-only | current | Pre-Amp Tx Pwr High Warning :This OID indicates that the Transmit Power is higher than the Warning theshold of the Pre-Amp Optical Module <Help> This warning i… |
| 1.3.6.1.4.1.20044.51.2.2.1.33.7 | ScalarpmoabphcAlmClientBiasLowWarning | read-only | current | Pre-Amp Bias Low Warning :This OID indicates that the Bias is lower than the Warning theshold of the Pre-Amp Optical Module <Help> This warning indicates if th… |
| 1.3.6.1.4.1.20044.51.2.2.1.33.8 | ScalarpmoabphcAlmClientBiasHighWarning | read-only | current | Pre-Amp Bias High Warning :This OID indicates that the Bias is higher than the Warning theshold of the Pre-Amp Optical Module <Help> This warning indicates if … |
| 1.3.6.1.4.1.20044.51.2.2.2 | NodepmoabphcAlmClientUrg | |||
| 1.3.6.1.4.1.20044.51.2.2.2.32 | NodepmoabphcAlmclientEdfaAlarms1 | |||
| 1.3.6.1.4.1.20044.51.2.2.2.32.1 | ScalarpmoabphcAlmClientGainLowAlarm | read-only | current | Pre-Amp Gain Low Alarm :This OID indicates that the Gain is lower than the alarm theshold of the Pre-Amp Module <Help> This alarm indicates if the Pre-Amp gain… |
| 1.3.6.1.4.1.20044.51.2.2.2.32.2 | ScalarpmoabphcAlmClientGainHighAlarm | read-only | current | Pre-Amp Gain High Alarm :This OID indicates that the Gain is higher than the alarm threshold of the Pre-Amp Module <Help> This alarm indicates if the Pre-Amp g… |
| 1.3.6.1.4.1.20044.51.2.2.2.32.3 | ScalarpmoabphcAlmClientInputPwrLowAlarm | read-only | current | Booster Rx Pwr Low Alarm :This OID indicates that the Receive Power is lower than the alarm theshold of the Booster Optical Module <Help> This alarm indicates … |
| 1.3.6.1.4.1.20044.51.2.2.2.32.4 | ScalarpmoabphcAlmClientInputPwrHighAlarm | read-only | current | Booster Rx Pwr High Alarm :This OID indicates that the Receive Power is higher than the alarm theshold of the Booster Optical Module <Help> This alarm indicate… |
| 1.3.6.1.4.1.20044.51.2.2.2.32.5 | ScalarpmoabphcAlmClientOutputPwrLowAlarm | read-only | current | Pre-Amp Tx Pwr Low Alarm :This OID indicates that the Transmit Power is lower than the alarm theshold of the Pre-Amp Optical Module <Help> This alarm indicates… |
| 1.3.6.1.4.1.20044.51.2.2.2.32.6 | ScalarpmoabphcAlmClientOutputPwrHighAlarm | read-only | current | Pre-Amp Tx Pwr High Alarm :This OID indicates that the Transmit Power is higher than the alarm theshold of the Pre-Amp Optical Module <Help> This alarm indicat… |
| 1.3.6.1.4.1.20044.51.2.2.2.32.7 | ScalarpmoabphcAlmClientBiasLowAlarm | read-only | current | Pre-Amp Bias Low Alarm :This OID indicates that the Bias is lower than the alarm theshold of the Pre-Amp Optical Module <Help> This alarm indicates if the Pre-… |
| 1.3.6.1.4.1.20044.51.2.2.2.32.8 | ScalarpmoabphcAlmClientBiasHighAlarm | read-only | current | Pre-Amp Bias High Alarm :This OID indicates that the Bias is higher than the alarm theshold of the Pre-Amp Optical Module <Help> This alarm indicates if the Pr… |
| 1.3.6.1.4.1.20044.51.2.2.3 | NodepmoabphcAlmClientCrit | |||
| 1.3.6.1.4.1.20044.51.2.2.3.8 | NodepmoabphcAlmsynthAlm8 | |||
| 1.3.6.1.4.1.20044.51.2.2.3.8.4 | ScalarpmoabphcAlmClientHwFail | read-only | current | Client Port HW Failure :This OID indicates a failure on Client port, most probably caused by a HW issue <Condtype> CLIENT_HW_FAIL <Probcause> equipmentMalfunct… |
| 1.3.6.1.4.1.20044.51.2.2.3.8.5 | ScalarpmoabphcAlmClientTxOff | read-only | current | Pre-Amp Optical Output Shutdown :This OID indicates the Pre-Amp optical output power is on <Help> This status indicates if the Pre-Amp laser pump transceiver l… |
| 1.3.6.1.4.1.20044.51.2.2.3.8.9 | ScalarpmoabphcAlmClientDdmWarning | read-only | current | Warning On Client Optical Module DDM :This OID indicates a warning is present coming out of Client optical interface DDM <Condtype> CLIENT_DDM_WARNING <Probcau… |
| 1.3.6.1.4.1.20044.51.2.2.3.8.10 | ScalarpmoabphcAlmClientDdmAlm | read-only | current | Alarm On Client Optical Module DDM :This OID indicates an alarm is present coming out of Client optical interface DDM <Condtype> CLIENT_DDM_ALM <Probcause> equ… |
| 1.3.6.1.4.1.20044.51.2.2.3.8.12 | ScalarpmoabphcAlmClientFail | read-only | current | Client Port Failure :This OID indicates a failure on the Client port <Condtype> CLIENT_FAIL <Probcause> equipmentMalfunction (16) <Alarmtype> synthesisAlarm (1… |
| 1.3.6.1.4.1.20044.51.2.2.3.8.13 | ScalarpmoabphcAlmClientExtPumpFail | read-only | current | Pre-Amp External Pump Fail :This OID indicates that the external pump linked to the Pre-Amp is in fail condition <Help> This alarm indicates if the external pu… |
| 1.3.6.1.4.1.20044.51.2.2.3.35 | NodepmoabphcAlmclientEdfaAlarms2 | |||
| 1.3.6.1.4.1.20044.51.2.2.3.35.1 | ScalarpmoabphcAlmClientEdfaNr | read-only | current | Pre-Amp Optical Module Not Ready :This OID indicates that the Pre-Amp Optical Module is not ready <Help> This status indicates if the Pre-Amp has been correctl… |
| 1.3.6.1.4.1.20044.51.2.2.3.35.2 | ScalarpmoabphcAlmClientEdfaTecFail | read-only | current | Pre-Amp TEC Fail :This OID indicates that the TEC is in fail condition on the Pre-Amp Optical Module <Help> This alarm indicates if the TEC of the Pre-Amp is i… |
| 1.3.6.1.4.1.20044.51.2.2.3.35.3 | ScalarpmoabphcAlmClientEdfaLaserFail | read-only | current | Pre-Amp Pump Laser Fail :This OID indicates a Transmit Laser Fail on the Pre-Amp Optical Module <Help> This alarm indicates if the laser of the Pre-Amp is in f… |
| 1.3.6.1.4.1.20044.51.2.2.3.35.4 | ScalarpmoabphcAlmClientEdfaLos | read-only | current | Booster Loss Of Signal :This OID indicates a Loss of Signal on the Booster Optical Module <Help> This alarm indicates if an optical signal is detected on the B… |
| 1.3.6.1.4.1.20044.51.2.2.3.35.5 | ScalarpmoabphcAlmClientExtPumpEdfaLowCurrent | read-only | current | Pre-Amp Pump Low Current :This OID indicates that the EDFA pump current of Pre-Amp is too low because of the external pump high power<Help> This alarm (only ac… |
| 1.3.6.1.4.1.20044.51.2.3 | NodepmoabphcAlmLine | |||
| 1.3.6.1.4.1.20044.51.2.3.1 | NodepmoabphcAlmLineNurg | |||
| 1.3.6.1.4.1.20044.51.2.3.1.41 | NodepmoabphcAlmlineEdfaWarnings | |||
| 1.3.6.1.4.1.20044.51.2.3.1.41.1 | ScalarpmoabphcAlmLineGainLowWarning | read-only | current | Booster Gain Low Warning :This OID indicates that the Gain is lower than the Warning theshold of the Booster Module <Help> This alarm indicates if the Booster … |
| 1.3.6.1.4.1.20044.51.2.3.1.41.2 | ScalarpmoabphcAlmLineGainHighWarning | read-only | current | Booster Gain High Warning :This OID indicates that the Gain is higher than the Warning threshold of the Booster Module <Help> This alarm indicates if the Boost… |
| 1.3.6.1.4.1.20044.51.2.3.1.41.3 | ScalarpmoabphcAlmLineInputPwrLowWarning | read-only | current | Pre-Amp Rx Pwr Low Warning :This OID indicates that the Receive Power is lower than the Warning theshold of the Pre-Amp Optical Module <Help> This warning indi… |
| 1.3.6.1.4.1.20044.51.2.3.1.41.4 | ScalarpmoabphcAlmLineInputPwrHighWarning | read-only | current | Pre-Amp Rx Pwr High Warning :This OID indicates that the Receive Power is higher than the Warning theshold of the Pre-Amp Optical Module <Help> This warning in… |
| 1.3.6.1.4.1.20044.51.2.3.1.41.5 | ScalarpmoabphcAlmLineOutputPwrLowWarning | read-only | current | Booster Tx Pwr Low Warning :This OID indicates that the Transmit Power is lower than the Warning theshold of the Booster Optical Module <Help> This warning ind… |
| 1.3.6.1.4.1.20044.51.2.3.1.41.6 | ScalarpmoabphcAlmLineOutputPwrHighWarning | read-only | current | Booster Tx Pwr High Warning :This OID indicates that the Transmit Power is higher than the Warning theshold of the Booster Optical Module <Help> This warning i… |
| 1.3.6.1.4.1.20044.51.2.3.1.41.7 | ScalarpmoabphcAlmLineBiasLowWarning | read-only | current | Booster Bias Low Warning :This OID indicates that the Bias is lower than the Warning theshold of the Booster Optical Module <Help> This warning indicates if th… |
| 1.3.6.1.4.1.20044.51.2.3.1.41.8 | ScalarpmoabphcAlmLineBiasHighWarning | read-only | current | Booster Bias High Warning :This OID indicates that the Bias is higher than the Warning theshold of the Booster Optical Module <Help> This warning indicates if … |
| 1.3.6.1.4.1.20044.51.2.3.2 | NodepmoabphcAlmLineUrg | |||
| 1.3.6.1.4.1.20044.51.2.3.2.40 | NodepmoabphcAlmlineEdfaAlarms1 | |||
| 1.3.6.1.4.1.20044.51.2.3.2.40.1 | ScalarpmoabphcAlmLineGainLowAlarm | read-only | current | Booster Gain Low Alarm :This OID indicates that the Gain is lower than the alarm theshold of the Booster Module <Help> This alarm indicates if the Booster gain… |
| 1.3.6.1.4.1.20044.51.2.3.2.40.2 | ScalarpmoabphcAlmLineGainHighAlarm | read-only | current | Booster Gain High Alarm :This OID indicates that the Gain is higher than the alarm threshold of the Booster Module <Help> This alarm indicates if the Booster g… |
| 1.3.6.1.4.1.20044.51.2.3.2.40.3 | ScalarpmoabphcAlmLineInputPwrLowAlarm | read-only | current | Pre-Amp Rx Pwr Low Alarm :This OID indicates that the Receive Power is lower than the alarm theshold of the Pre-Amp Optical Module <Help> This alarm indicates … |
| 1.3.6.1.4.1.20044.51.2.3.2.40.4 | ScalarpmoabphcAlmLineInputPwrHighAlarm | read-only | current | Pre-Amp Rx Pwr High Alarm :This OID indicates that the Receive Power is higher than the alarm theshold of the Pre-Amp Optical Module <Help> This alarm indicate… |
| 1.3.6.1.4.1.20044.51.2.3.2.40.5 | ScalarpmoabphcAlmLineOutputPwrLowAlarm | read-only | current | Booster Tx Pwr Low Alarm :This OID indicates that the Transmit Power is lower than the alarm theshold of the Booster Optical Module <Help> This alarm indicates… |
| 1.3.6.1.4.1.20044.51.2.3.2.40.6 | ScalarpmoabphcAlmLineOutputPwrHighAlarm | read-only | current | Booster Tx Pwr High Alarm :This OID indicates that the Transmit Power is higher than the alarm theshold of the Booster Optical Module <Help> This alarm indicat… |
| 1.3.6.1.4.1.20044.51.2.3.2.40.7 | ScalarpmoabphcAlmLineBiasLowAlarm | read-only | current | Booster Bias Low Alarm :This OID indicates that the Bias is lower than the alarm theshold of the Booster Optical Module <Help> This alarm indicates if the Boos… |
| 1.3.6.1.4.1.20044.51.2.3.2.40.8 | ScalarpmoabphcAlmLineBiasHighAlarm | read-only | current | Booster Bias High Alarm :This OID indicates that the Bias is higher than the alarm theshold of the Booster Optical Module <Help> This alarm indicates if the Bo… |
| 1.3.6.1.4.1.20044.51.2.3.3 | NodepmoabphcAlmLineCrit | |||
| 1.3.6.1.4.1.20044.51.2.3.3.7 | NodepmoabphcAlmsynthAlm7 | |||
| 1.3.6.1.4.1.20044.51.2.3.3.7.4 | ScalarpmoabphcAlmLineHwFail | read-only | current | Line Port HW Failure :This OID indicates a failure on line port, most probably caused by a HW issue <Condtype> LINE_HW_FAIL <Probcause> equipmentMalfunction (1… |
| 1.3.6.1.4.1.20044.51.2.3.3.7.5 | ScalarpmoabphcAlmLineTxOff | read-only | current | Booster Optical Output Shutdown :This OID indicates the Booster optical output power is on <Help> This status indicates if the Booster laser pump is ON or OFF … |
| 1.3.6.1.4.1.20044.51.2.3.3.7.9 | ScalarpmoabphcAlmLineDdmWarning | read-only | current | Warning On Line Optical Module DDM :This OID indicates a warning is present coming out of Line optical interface DDM <Condtype> LINE_DDM_WARNING <Probcause> eq… |
| 1.3.6.1.4.1.20044.51.2.3.3.7.10 | ScalarpmoabphcAlmLineDdmAlm | read-only | current | Alarm On Line Optical Module DDM :This OID indicates an alarm is present coming out of Line optical interface DDM <Condtype> LINE_DDM_ALM <Probcause> equipment… |
| 1.3.6.1.4.1.20044.51.2.3.3.7.12 | ScalarpmoabphcAlmLineFail | read-only | current | Line Port Failure :This OID indicates a failure on the line port <Condtype> LINE_FAIL <Probcause> equipmentMalfunction (16) <Alarmtype> synthesisAlarm (12) <Po… |
| 1.3.6.1.4.1.20044.51.2.3.3.7.13 | ScalarpmoabphcAlmLineExtPumpFail | read-only | current | Booster External Pump Fail :This OID indicates that the external pump linked to the Booster is in fail condition <Help> This alarm indicates if the external pu… |
| 1.3.6.1.4.1.20044.51.2.3.3.43 | NodepmoabphcAlmlineEdfaAlarms2 | |||
| 1.3.6.1.4.1.20044.51.2.3.3.43.1 | ScalarpmoabphcAlmLineEdfaNr | read-only | current | Booster Optical Module Not Ready :This OID indicates that the Booster Optical Module is not ready <Help> This status indicates if the Booster has been correctl… |
| 1.3.6.1.4.1.20044.51.2.3.3.43.2 | ScalarpmoabphcAlmLineEdfaTecFail | read-only | current | Booster TEC Fail :This OID indicates that the TEC is in fail condition on the Booster Optical Module <Help> This alarm indicates if the TEC of the Booster is i… |
| 1.3.6.1.4.1.20044.51.2.3.3.43.3 | ScalarpmoabphcAlmLineEdfaLaserFail | read-only | current | Booster Pump Laser Fail :This OID indicates a Transmit Laser Fail on the Booster Optical Module <Help> This alarm indicates if the laser of the Booster is in f… |
| 1.3.6.1.4.1.20044.51.2.3.3.43.4 | ScalarpmoabphcAlmLineEdfaLos | read-only | current | Pre-Amp Loss Of Signal :This OID indicates a Loss of Signal on the Pre-Amp Optical Module <Help> This alarm indicates if an optical signal is detected on the P… |
| 1.3.6.1.4.1.20044.51.2.3.3.43.5 | ScalarpmoabphcAlmLineExtPumpEdfaLowCurrent | read-only | current | Booster Pump Low Current :This OID indicates that the EDFA pump current of Booster is too low because of the external pump high power<Help> This alarm (only ac… |
| 1.3.6.1.4.1.20044.51.3 | Nodepmoabphcmeasures | |||
| 1.3.6.1.4.1.20044.51.3.1 | NodepmoabphcMesrOther | |||
| 1.3.6.1.4.1.20044.51.3.1.72 | ScalarpmoabphcMesrtempMeas | read-only | current | Module Temperature :This OID gives the temperature of the PM (Temperature =AV/256) (Unit = C) <Help> This measure gives the temperature of the module |
| 1.3.6.1.4.1.20044.51.3.2 | NodepmoabphcMesrClient | |||
| 1.3.6.1.4.1.20044.51.3.2.32 | ScalarpmoabphcMesrclientEdfaBiasMeas | read-only | current | Pre-Amp Pump Laser Current :This OID gives the pump laser current of the Pre-Amp Optical Module (Current =AV/100) (Unit = mA) <Help> This measure gives the bia… |
| 1.3.6.1.4.1.20044.51.3.2.33 | ScalarpmoabphcMesrclientEdfaTxpwrMeas | read-only | current | Pre-Amp Tx Power :This OID gives the transmit power value of the Pre-Amp Optical Module (Power =(AV-32768)*0,005) (Unit = dBm) <Help> This measure gives the Tx… |
| 1.3.6.1.4.1.20044.51.3.2.34 | ScalarpmoabphcMesrclientEdfaRxpwrMeas | read-only | current | Booster Rx Power :This OID gives the receive power value of the Booster Optical Module (Power =(AV-32768)*0,005) (Unit = dBm) <Help> This measure gives the Rx … |
| 1.3.6.1.4.1.20044.51.3.2.35 | ScalarpmoabphcMesrclientEdfaGainMeas | read-only | current | Pre-Amp Gain Target :This OID gives the gain value of the Pre-Amp Module (Gain =(AV-32768)*0,005) (Unit = dB) <Help> This information gives the target gain of … |
| 1.3.6.1.4.1.20044.51.3.2.38 | ScalarpmoabphcMesrclientCorrectedGain | read-only | current | Pre-Amp Gain :This OID gives the gain value of the Pre-Amp Module corrected by the ASE compensation mechanism (Gain =(AV-32768)*0,005) (Unit = dB) <Help> This … |
| 1.3.6.1.4.1.20044.51.3.3 | NodepmoabphcMesrLine | |||
| 1.3.6.1.4.1.20044.51.3.3.40 | ScalarpmoabphcMesrlineEdfaBiasMeas | read-only | current | Booster Pump Laser Current :This OID gives the pump laser current of the Booster Optical Module (Current =AV/100) (Unit = mA) <Help> This measure gives the bia… |
| 1.3.6.1.4.1.20044.51.3.3.41 | ScalarpmoabphcMesrlineEdfaTxpwrMeas | read-only | current | Booster Tx Power :This OID gives the transmit power value of the Booster Optical Module (Power =(AV-32768)*0,005) (Unit = dBm) <Help> This measure gives the Tx… |
| 1.3.6.1.4.1.20044.51.3.3.42 | ScalarpmoabphcMesrlineEdfaRxpwrMeas | read-only | current | Pre-Amp Rx Power :This OID gives the receive power value of the Pre-Amp Optical Module (Power =(AV-32768)*0,005) (Unit = dBm) <Help> This measure gives the Rx … |
| 1.3.6.1.4.1.20044.51.3.3.43 | ScalarpmoabphcMesrlineEdfaGainMeas | read-only | current | Booster Gain Target :This OID gives the gain value of the Booster Module (Gain =(AV-32768)*0,005) (Unit = dB) <Help> This information gives the target gain of … |
| 1.3.6.1.4.1.20044.51.3.3.46 | ScalarpmoabphcMesrlineCorrectedGain | read-only | current | Booster Gain :This OID gives the gain value of the Booster Module corrected by the ASE compensation mechanism (Gain =(AV-32768)*0,005) (Unit = dB) <Help> This … |
| 1.3.6.1.4.1.20044.51.6 | NodepmoabphccontrolsWrite | |||
| 1.3.6.1.4.1.20044.51.6.1 | NodepmoabphcCtrlOther | |||
| 1.3.6.1.4.1.20044.51.6.1.0 | NodepmoabphcCtrlsynth0 | |||
| 1.3.6.1.4.1.20044.51.6.1.0.1 | ScalarpmoabphcCtrlConfLoad | read-write | current | Load Configuration Tables :When set this enables loading from flash configuration1 into the module. |
| 1.3.6.1.4.1.20044.51.6.1.0.9 | ScalarpmoabphcCtrlConfFlash | read-write | current | Write Configuration Tables :This bit saves the current configuration of the module as configuration in the flash. <Help> This control saves the customer config… |
| 1.3.6.1.4.1.20044.51.6.1.0.13 | ScalarpmoabphcCtrlConfClear | read-write | current | Clear Configuration Tables :This bit clears the configuration tables from configuration in the flash. <Help> This control restores the default configuration of… |
| 1.3.6.1.4.1.20044.51.6.1.5 | NodepmoabphcCtrlswMgnt | |||
| 1.3.6.1.4.1.20044.51.6.1.5.2 | ScalarpmoabphcCtrlColdReset | read-write | current | PM Cold Reset :This OID, when set, causes a cold reset of the Software. This reset is traffic affecting, and the configuration of Software is reloaded on start… |
| 1.3.6.1.4.1.20044.51.6.1.5.3 | ScalarpmoabphcCtrlWarmReset | read-write | current | PM Warm Reset :This OID, when set, causes a warm reset of the Software. This reset is not traffic affecting, and the configuration of the Sofwtare remains unch… |
| 1.3.6.1.4.1.20044.51.6.1.73 | NodepmoabphcCtrlledTest | |||
| 1.3.6.1.4.1.20044.51.6.1.73.1 | ScalarpmoabphcCtrlGreenLed | read-write | current | Green Leds Test :This OID switches on all the green Leds as a test feature. <Help> This control initiates a test leds turning all the LEDs to green |
| 1.3.6.1.4.1.20044.51.6.1.73.2 | ScalarpmoabphcCtrlRedLed | read-write | current | Red Leds Test :This OID switches on all the red Leds as a test feature. <Help> This control initiates a test leds turning all the LEDs to red |
| 1.3.6.1.4.1.20044.51.6.1.73.3 | ScalarpmoabphcCtrlLedOff | read-write | current | Leds Off :This OID switches off all the Leds as a test feature. <Help> This control initiates a test leds turning all the LEDs to OFF |
| 1.3.6.1.4.1.20044.51.6.1.75 | NodepmoabphcCtrlmaintMode | |||
| 1.3.6.1.4.1.20044.51.6.1.75.1 | ScalarpmoabphcCtrlMaintenance | read-write | current | PM Maintenance Mode :This OID sets the PM in maintenance mode <Help> This control enables the maintenance mode of the module |
| 1.3.6.1.4.1.20044.51.6.1.76 | NodepmoabphcCtrlaprRestart | |||
| 1.3.6.1.4.1.20044.51.6.1.76.1 | ScalarpmoabphcCtrlAprManualRestart | read-write | current | APR Manual Restart :This OID initiates the Restart mechanism to retrieve from the APR state.<Help> This control initiates the Restart mechanism to retrieve fro… |
| 1.3.6.1.4.1.20044.51.6.2 | NodepmoabphcCtrlClient | |||
| 1.3.6.1.4.1.20044.51.6.2.32 | NodepmoabphcCtrlclientEdfaLaserOff | |||
| 1.3.6.1.4.1.20044.51.6.2.32.1 | ScalarpmoabphcCtrlClientEdfaLaserOff | read-write | current | Pre-Amp Optical Module Laser Off :This OID switches OFF the laser of the Pre-Amp Optical Module <Help> This control defines the laser state of the Pre-Amp |
| 1.3.6.1.4.1.20044.51.6.2.34 | ScalarpmoabphcCtrlclientGainCstMonitorValue | read-write | current | Pre-Amp Fiber Aging Period :This OID sets the value of the monitoring period to detect a fiber aging. (Unit = s) This value sets the monitoring period to detec… |
| 1.3.6.1.4.1.20044.51.6.2.35 | ScalarpmoabphcCtrlclientGainCstPoutValue | read-write | current | Pre-Amp Ref Pout :This OID sets the value of the reference output power used to compensate the fiber aging (active only in constant gain mode) (AV=(Gain/0,005)… |
| 1.3.6.1.4.1.20044.51.6.2.36 | ScalarpmoabphcCtrlclientGainSettingValue | read-write | current | Pre-Amp Gain Target :This OID sets the value of the nominal gain of the Pre-Amplifier Module (active only in constant output power mode) (AV=(Gain/0,005) + 327… |
| 1.3.6.1.4.1.20044.51.6.2.37 | NodepmoabphcCtrlclientGainProcessing | |||
| 1.3.6.1.4.1.20044.51.6.2.37.1 | ScalarpmoabphcCtrlClientGainProc | read-write | current | Pre-Amp Gain Adjustment :This OID initiates the automatic nominal gain adjustment on the Pre-Amplifier Module<Help> This control initiates the automatic nomina… |
| 1.3.6.1.4.1.20044.51.6.2.38 | ScalarpmoabphcCtrlclientGainCstFiberAgingMarginValue | read-write | current | Pre-Amp Aging Threshold :This OID sets the threshold to consider the power drop as a fiber aging. (active only in constant gain mode) (AV=(Gain/0,005) + 32768)… |
| 1.3.6.1.4.1.20044.51.6.2.39 | ScalarpmoabphcCtrlclientGainCstAdddropMarginValue | read-write | current | Pre-Amp AddDrop Threshold :This OID sets the threshold to not consider the power drop as a fiber aging. (active only in constant gain mode) (AV=(Gain/0,005) + … |
| 1.3.6.1.4.1.20044.51.6.3 | NodepmoabphcCtrlLine | |||
| 1.3.6.1.4.1.20044.51.6.3.40 | NodepmoabphcCtrllineEdfaLaserOff | |||
| 1.3.6.1.4.1.20044.51.6.3.40.1 | ScalarpmoabphcCtrlLineEdfaLaserOff | read-write | current | Booster Optical Module Laser Off :This OID switches OFF the laser of the Booster Optical Module <Help> This control defines the laser state of the Booster |
| 1.3.6.1.4.1.20044.51.6.3.42 | ScalarpmoabphcCtrllineGainCstMonitorValue | read-write | current | Booster Fiber Aging Period :This OID sets the value of the monitoring period to detect a fiber aging. (Unit = s) This value sets the monitoring period to detec… |
| 1.3.6.1.4.1.20044.51.6.3.43 | ScalarpmoabphcCtrllineGainCstPoutValue | read-write | current | Booster Ref Pout :This OID sets the value of the reference output power used to compensate the fiber aging (active only in constant gain mode) (AV=(Gain/0,005)… |
| 1.3.6.1.4.1.20044.51.6.3.44 | ScalarpmoabphcCtrllineGainSettingValue | read-write | current | Booster Gain Target :This OID sets the value of the nominal gain of the Booster Module (active only in constant output power mode) (AV=(Gain/0,005) + 32768) (U… |
| 1.3.6.1.4.1.20044.51.6.3.45 | NodepmoabphcCtrllineGainProcessing | |||
| 1.3.6.1.4.1.20044.51.6.3.45.1 | ScalarpmoabphcCtrlLineGainProc | read-write | current | Booster Gain Adjustment :This OID initiates the automatic nominal gain adjustment on the Booster Module<Help> This control initiates the automatic nominal gain… |
| 1.3.6.1.4.1.20044.51.6.3.46 | ScalarpmoabphcCtrllineGainCstFiberAgingMarginValue | read-write | current | Booster Aging Threshold :This OID sets the threshold to consider the power drop as a fiber aging. (active only in constant gain mode) (AV=(Gain/0,005) + 32768)… |
| 1.3.6.1.4.1.20044.51.6.3.47 | ScalarpmoabphcCtrllineGainCstAdddropMarginValue | read-write | current | Booster AddDrop Threshold :This OID sets the threshold to not consider the power drop as a fiber aging. (active only in constant gain mode) (AV=(Gain/0,005) + … |
| 1.3.6.1.4.1.20044.51.7 | Nodepmoabphcri | |||
| 1.3.6.1.4.1.20044.51.7.2 | ScalarpmoabphcRinvReloadInventory | read-write | current | Reload the inventory: This OID triggers an inventory reload. |
| 1.3.6.1.4.1.20044.51.7.3 | ScalarpmoabphcRinvModulePlatform | read-only | current | Module platform description: This OID contains the description of the Module. |
| 1.3.6.1.4.1.20044.51.7.4 | ScalarpmoabphcRinvSwPlatform | read-only | current | SW platform description: This OID contains the description of the Software platform. |
| 1.3.6.1.4.1.20044.51.7.5 | ScalarpmoabphcRinvSwFoa | read-only | current | Optical device driver description: This OID contains the description of the driver of the optical devices (Booster and Pre-Amp) |
| 1.3.6.1.4.1.20044.51.7.6 | TablepmoabphcRinvBoosterTable | not-accessible | current | List of the Boosters on the selected module |
| 1.3.6.1.4.1.20044.51.7.6.1 | RowpmoabphcRinvBoosterEntry | not-accessible | current | Row definition for the Boosters table |
| 1.3.6.1.4.1.20044.51.7.6.1.1 | ColumnpmoabphcRinvBoosterIndex | read-only | current | Index for Booster table |
| 1.3.6.1.4.1.20044.51.7.6.1.2 | ColumnpmoabphcRinvBooster | read-only | current | Inventory for the Booster: This OID contains the inventory for the Booster |
| 1.3.6.1.4.1.20044.51.7.7 | TablepmoabphcRinvPreAmpTable | not-accessible | current | List of the PreAmps on the selected module |
| 1.3.6.1.4.1.20044.51.7.7.1 | RowpmoabphcRinvPreAmpEntry | not-accessible | current | Row definition for the PreAmp table |
| 1.3.6.1.4.1.20044.51.7.7.1.1 | ColumnpmoabphcRinvPreAmpIndex | read-only | current | Index for PreAmp table |
| 1.3.6.1.4.1.20044.51.7.7.1.2 | ColumnpmoabphcRinvPreAmp | read-only | current | Inventory for the PreAmp: This OID contains the inventory for the PreAmp |
| 1.3.6.1.4.1.20044.51.9 | NodepmoabphcConfig | |||
| 1.3.6.1.4.1.20044.51.9.1 | NodepmoabphcCfgNoValue | |||
| 1.3.6.1.4.1.20044.51.9.1.1 | NodepmoabphctableclientStartup | |||
| 1.3.6.1.4.1.20044.51.9.1.1.2 | ScalarpmoabphcCfgclientEdfaLaserCtrl | read-write | current | Default Settings on Client Laser :This OID configures the default initialisation settings on the client laser. |
| 1.3.6.1.4.1.20044.51.9.1.1.3 | ScalarpmoabphcCfgclientEdfaLaserMode | read-write | current | Default Settings on Client mode :This OID configures the default mode on the client amplifier. |
| 1.3.6.1.4.1.20044.51.9.1.1.4 | ScalarpmoabphcCfgclientGainValue | read-write | current | Default Settings on Client Gain :This OID configures the default gain on the client amplifier. |
| 1.3.6.1.4.1.20044.51.9.1.1.5 | ScalarpmoabphcCfgclientTiltValue | read-write | current | Default Settings on Client Tilt :This OID configures the default tilt on the client amplifier. |
| 1.3.6.1.4.1.20044.51.9.1.1.6 | ScalarpmoabphcCfgclientMsaLoss | read-write | current | Default Settings on Client MSA :This OID configures the default MSA value on the client amplifier. |
| 1.3.6.1.4.1.20044.51.9.1.1.7 | ScalarpmoabphcCfgclientOutputPowerValue | read-write | current | Default Settings on Client Output power :This OID configures the default Output power value on the client amplifier. |
| 1.3.6.1.4.1.20044.51.9.1.1.8 | ScalarpmoabphcCfgclientAseCompensation | read-write | current | Default Settings on Client ASE :This OID configures the default ASE compensation value on the client amplifier. |
| 1.3.6.1.4.1.20044.51.9.2 | NodepmoabphcCfgLineStartUp | |||
| 1.3.6.1.4.1.20044.51.9.2.1 | NodepmoabphctablelineStartup | |||
| 1.3.6.1.4.1.20044.51.9.2.1.2 | ScalarpmoabphcCfglineEdfaLaserCtrl | read-write | current | Default Settings on Line Laser :This OID configures the default initialisation settings on the line laser. |
| 1.3.6.1.4.1.20044.51.9.2.1.3 | ScalarpmoabphcCfglineEdfaLaserMode | read-write | current | Default Settings on Line mode :This OID configures the default mode on the line amplifier. |
| 1.3.6.1.4.1.20044.51.9.2.1.4 | ScalarpmoabphcCfglineGainValue | read-write | current | Default Settings on Line Gain :This OID configures the default gain on the line amplifier. |
| 1.3.6.1.4.1.20044.51.9.2.1.5 | ScalarpmoabphcCfglineTiltValue | read-write | current | Default Settings on Line Tilt :This OID configures the default tilt on the line amplifier. |
| 1.3.6.1.4.1.20044.51.9.2.1.6 | ScalarpmoabphcCfglineMsaLoss | read-write | current | Default Settings on Line MSA :This OID configures the default MSA value on the line amplifier. |
| 1.3.6.1.4.1.20044.51.9.2.1.7 | ScalarpmoabphcCfglineOutputPowerValue | read-write | current | Default Settings on Line Output power :This OID configures the default Output power value on the line amplifier. |
| 1.3.6.1.4.1.20044.51.9.2.1.8 | ScalarpmoabphcCfglineAseCompensation | read-write | current | Default Settings on Line ASE :This OID configures the default ASE compensation value on the line amplifier. |
| 1.3.6.1.4.1.20044.51.9.2.1.11 | ScalarpmoabphcCfgaprMode | read-write | current | Default setting on module :This OID configures the default mode on the APR |
| 1.3.6.1.4.1.20044.51.9.3 | NodepmoabphcCfgLabels | |||
| 1.3.6.1.4.1.20044.51.9.3.1 | TablepmoabphcCfgLabelclientTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.51.9.3.1.1 | RowpmoabphcCfgLabelclientEntry | not-accessible | current | Row definition for the labels table |
| 1.3.6.1.4.1.20044.51.9.3.1.1.1 | ColumnpmoabphcCfgLabelclientIndex | read-only | current | Index definition for the labelclient table |
| 1.3.6.1.4.1.20044.51.9.3.1.1.3 | ColumnpmoabphcCfgLabelclientPortn | read-write | current | Default settings on the label of the Ports :These registers configures the default initialisation settings of the labels of the ports. |
| 1.3.6.1.4.1.20044.51.9.3.2 | TablepmoabphcCfgLabellineTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.51.9.3.2.1 | RowpmoabphcCfgLabellineEntry | not-accessible | current | Row definition for the labels table |
| 1.3.6.1.4.1.20044.51.9.3.2.1.1 | ColumnpmoabphcCfgLabellineIndex | read-only | current | Index definition for the labelline table |
| 1.3.6.1.4.1.20044.51.9.3.2.1.3 | ColumnpmoabphcCfgLabellinePortn | read-write | current | Default settings on the label of the lines :These registers configures the default initialisation settings of the labels of the lines. |
| 1.3.6.1.4.1.20044.51.9.257 | ScalarpmoabphcCfgWriteConfiguration | read-write | current | Write configuration to module:This OID writes the complete configuration to the module |
| 1.3.6.1.4.1.20044.51.10 | Nodepmoabphctraps | |||
| 1.3.6.1.4.1.20044.51.10.4 | ScalarpmoabphctrapBoardNumber | read-only | current | Last module which generates a trap |
| 1.3.6.1.4.1.20044.51.10.30 | NotificationpmoabphcLineTrapNotUrgentGoesOn | current | Not urgent Line default is activated | |
| 1.3.6.1.4.1.20044.51.10.31 | NotificationpmoabphcLineTrapNotUrgentGoesOff | current | Not urgent Line default disappeared | |
| 1.3.6.1.4.1.20044.51.10.32 | NotificationpmoabphcLineTrapUrgentGoesOn | current | Urgent Line default is activated | |
| 1.3.6.1.4.1.20044.51.10.33 | NotificationpmoabphcLineTrapUrgentGoesOff | current | Urgent Line default disappeared | |
| 1.3.6.1.4.1.20044.51.10.34 | NotificationpmoabphcLineTrapCritGoesOn | current | Critical Line default is activated | |
| 1.3.6.1.4.1.20044.51.10.35 | NotificationpmoabphcLineTrapCritGoesOff | current | Critical Line default disappeared | |
| 1.3.6.1.4.1.20044.51.10.40 | NotificationpmoabphcClientTrapNotUrgentGoesOn | current | Not urgent client default is activated | |
| 1.3.6.1.4.1.20044.51.10.41 | NotificationpmoabphcClientTrapNotUrgentGoesOff | current | Not urgent client default disappeared | |
| 1.3.6.1.4.1.20044.51.10.42 | NotificationpmoabphcClientTrapUrgentGoesOn | current | Urgent client default is activated | |
| 1.3.6.1.4.1.20044.51.10.43 | NotificationpmoabphcClientTrapUrgentGoesOff | current | Urgent client default disappeared | |
| 1.3.6.1.4.1.20044.51.10.44 | NotificationpmoabphcClientTrapCritGoesOn | current | Critical client default is activated | |
| 1.3.6.1.4.1.20044.51.10.45 | NotificationpmoabphcClientTrapCritGoesOff | current | Critical client default disappeared | |
| 1.3.6.1.4.1.20044.51.10.50 | NotificationpmoabphcPowerTrapUrgentGoesOn | current | Urgent power supply default is activated | |
| 1.3.6.1.4.1.20044.51.10.51 | NotificationpmoabphcPowerTrapUrgentGoesOff | current | Urgent power supply default disappeared |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| PmoabphcaprMode | INTEGER { oabphcaproffmode(0), oabphcaprsemiautomode(1), oabphcaprautomode(2) oabphcaprlossforwardingmode(3) oabphcaprrepeatmode(4) } | current | Different modes on APR |
| PmoabphcBoosterCstGainAdjMode | INTEGER { oabphcboostercstgainadjsemiautomode(1), oabphcboostercstgainadjautomode(2) } | current | Different modes when constant Gain |
| PmoabphcBoosterGainAdjMode | INTEGER { oabphcboostergainadjmanualmode(0), oabphcboostergainadjsemiautomode(1), oabphcboostergainadjautomode(2) } | current | Different modes on Gain |
| PmoabphcboosterMode | INTEGER { oabphcboosterdefaultmode(0), oabphcboosterconstantcurrentmode(1), oabphcboosterconstantpowermode(2) oabphcboosterconstantgainmode(3) oabphcboosterpoutpinmode(4) oabphcboostermanualmode(5) oabphcboosterfeedforwardmode(6) oabphcboostertransientsupmode(7) } | current | Different modes on OA booster |
| PmoabphcPreampCstGainAdjMode | INTEGER { oabphcpreampcstgainadjsemiautomode(1), oabphcpreampcstgainadjautomode(2) } | current | Different modes when constant Gain |
| PmoabphcPreampGainAdjMode | INTEGER { oabphcpreampgainadjmanualmode(0), oabphcpreampgainadjsemiautomode(1), oabphcpreampgainadjautomode(2) } | current | Different modes on Gain |
| PmoabphcpreampMode | INTEGER { oabphcpreampdefaultmode(0), oabphcpreampconstantcurrentmode(1), oabphcpreampconstantpowermode(2) oabphcpreampconstantgainmode(3) oabphcpreamppoutpinmode(4) oabphcpreampmanualmode(5) oabphcpreampfeedforwardmode(6) oabphcpreamptransientsupmode(7) } | current | Different modes on OA preamp |