EKINOPS-Rm10010mp-MIB
703 objects
Creation.
Imported Objects
| EKINOPS-MIB | EkiApiState EkiMeasureType EkiMode ekinops EkiOnOff EkiProtocol EkiState EkiSynchroMode |
| SNMPv2-SMI | Counter32 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.20044.54 | IdentitymoduleRm10010mp | Creation. | ||
| 1.3.6.1.4.1.20044.54.2 | Noderm10010mpalarms | |||
| 1.3.6.1.4.1.20044.54.2.1 | Noderm10010mpAlmOther | |||
| 1.3.6.1.4.1.20044.54.2.1.1 | Noderm10010mpAlmOtherNurg | |||
| 1.3.6.1.4.1.20044.54.2.1.1.2 | Noderm10010mpAlmsynthAlm2 | |||
| 1.3.6.1.4.1.20044.54.2.1.1.2.1 | Scalarrm10010mpAlmConfTableSave | read-only | current | PM Configuration Save :This OID is at 1 during the saving of a new configuration table in the module Flash memory. <Condtype> CONF_TABLE_SAVE <Probcause> infor… |
| 1.3.6.1.4.1.20044.54.2.1.1.2.2 | Scalarrm10010mpAlmInvUpload | read-only | current | Inventory Upload :This OID is at 1 during the uploading of PM inventory information. <Condtype> INV_UPLOAD <Probcause> informationalStatus(1000) <Alarmtype> ot… |
| 1.3.6.1.4.1.20044.54.2.1.1.2.3 | Scalarrm10010mpAlmConfTableLoad | read-only | current | PM Configuration Load :This OID is at 1 during the loading of configuration tables in the modules RAM. <Condtype> CONF_TABLE_LOAD <Probcause> informationalStat… |
| 1.3.6.1.4.1.20044.54.2.1.1.2.4 | Scalarrm10010mpAlmCorrelatOff | read-only | current | Not Used :This OID, when set, indicates that alarm correlation is not being performed. <Condtype> CORRELAT_OFF <Probcause> informationalStatus(1000) <Alarmtype… |
| 1.3.6.1.4.1.20044.54.2.1.1.2.5 | Scalarrm10010mpAlmMaintenanceOn | read-only | current | Maintenance Mode :This OID indicates that the RM is in maintenance mode. <Help> This alarm indicates that the maintenance mode is enabled on the PM <Condtype> … |
| 1.3.6.1.4.1.20044.54.2.1.2 | Noderm10010mpAlmOtherUrg | |||
| 1.3.6.1.4.1.20044.54.2.1.2.248 | Noderm10010mpAlmmodFanFail | |||
| 1.3.6.1.4.1.20044.54.2.1.2.248.1 | Scalarrm10010mpAlmFanModuleAbsent | read-only | current | Fan Module Absent :This OID indicates the presence of the FAN module in the Chassis. <Help> This alarm indicates if the FAN module is detected in the chassis. … |
| 1.3.6.1.4.1.20044.54.2.1.2.248.2 | Scalarrm10010mpAlmFansFail | read-only | current | Fan Module Failure :This OID indicates that at least one of the 4 FAN unit of the FAN module is in fail condition <Help> This alarm indicates if one the FANs i… |
| 1.3.6.1.4.1.20044.54.2.1.2.248.4 | Scalarrm10010mpAlmFan1Fail | read-only | current | Fan Unit N�1 Failed On Fan Module :This OID indicates a failure on fan 1. Removal of the fan unit or no rotation sets the OID. <Help> This alarm indicates if… |
| 1.3.6.1.4.1.20044.54.2.1.2.248.5 | Scalarrm10010mpAlmFan2Fail | read-only | current | Fan Unit N�2 Failed On Fan Module :This OID indicates a failure on fan 2. Removal of the fan unit or no rotation sets the OID. <Help> This alarm indicates if… |
| 1.3.6.1.4.1.20044.54.2.1.2.248.6 | Scalarrm10010mpAlmFan3Fail | read-only | current | Fan Unit N�3 Failed On Fan Module :This OID indicates a failure on fan 3. Removal of the fan unit or no rotation sets the OID. <Help> This alarm indicates if… |
| 1.3.6.1.4.1.20044.54.2.1.2.248.7 | Scalarrm10010mpAlmFan4Fail | read-only | current | Fan Unit N�4 Failed On Fan Module :This OID indicates a failure on fan 4. Removal of the fan unit or no rotation sets the OID. <Help> This alarm indicates if… |
| 1.3.6.1.4.1.20044.54.2.1.3 | Noderm10010mpAlmOtherCrit | |||
| 1.3.6.1.4.1.20044.54.2.1.3.0 | Noderm10010mpAlmsynthAlm0 | |||
| 1.3.6.1.4.1.20044.54.2.1.3.0.2 | Scalarrm10010mpAlmFailFan | read-only | current | Fan Fail :This OID is at 1 when any fail occurs on the fan tray <Help> This alarm indicates that the Fan tray module is in a failure condition <Condtype> FAIL_… |
| 1.3.6.1.4.1.20044.54.2.1.3.0.9 | Scalarrm10010mpAlmModGlobFail | read-only | current | Module Failure :This OID is set on detection of a failure originating from the RM <Help> This alarm is set on detection of a failure originating from the equip… |
| 1.3.6.1.4.1.20044.54.2.1.3.0.15 | Scalarrm10010mpAlmDefFuseA | read-only | current | Fuse A Fail :This OID indicates that the fuse of the power input A is in fail condition <Help> Status of the Fuse A <Condtype> DEF_FUSE_A <Probcause> powerProb… |
| 1.3.6.1.4.1.20044.54.2.1.3.0.16 | Scalarrm10010mpAlmDefFuseB | read-only | current | Fuse B Fail :This OID indicates that the fuse of the power input B is in fail condition <Help> Status of the Fuse B <Condtype> DEF_FUSE_B <Probcause> powerProb… |
| 1.3.6.1.4.1.20044.54.2.1.3.40 | Noderm10010mpAlmclientModuleState | |||
| 1.3.6.1.4.1.20044.54.2.1.3.40.1 | Scalarrm10010mpAlmCfpInitialize | read-only | current | Client Trscv Initialize :This OID indicates the Client Trscv initialization is in progress <Help> Status indicating the Client Trscv initialization is in progr… |
| 1.3.6.1.4.1.20044.54.2.1.3.40.2 | Scalarrm10010mpAlmCfpLowPower | read-only | current | Client Trscv Low Power :This OID indicates the Client Trscv is in low power state <Help> Status indicating the Client Trscv is in low power state <Condtype> CF… |
| 1.3.6.1.4.1.20044.54.2.1.3.40.3 | Scalarrm10010mpAlmCfpHighPowerUp | read-only | current | Client Trscv High Power Up :This OID indicates the Client Trscv is leaving Low Power state <Help> Status indicating the Client Trscv is leaving Low Power state… |
| 1.3.6.1.4.1.20044.54.2.1.3.40.4 | Scalarrm10010mpAlmCfpTxOff | read-only | current | Client Trscv Laser Shutdown :This OID indicates the Client Trscv Laser is OFF <Help> Status indicating the Client Trscv Laser is OFF <Condtype> CFP_TX_OFF <Pro… |
| 1.3.6.1.4.1.20044.54.2.1.3.40.5 | Scalarrm10010mpAlmCfpTxTurnOn | read-only | current | Client Trscv Laser Turn On :This OID indicates the Client Trscv is turning on its laser <Help> Status indicating the Client Trscv is turning on its laser <Cond… |
| 1.3.6.1.4.1.20044.54.2.1.3.40.6 | Scalarrm10010mpAlmCfpReady | read-only | current | Client Trscv Ready :This OID indicates the Client Trscv is ready to operate <Help> Status indicating the Client Trscv is ready to operate <Condtype> CFP_READY … |
| 1.3.6.1.4.1.20044.54.2.1.3.40.7 | Scalarrm10010mpAlmCfpFault | read-only | current | Client Trscv Fault :This OID indicates the Client Trscv is in Fault state <Help> Status indicating the Client Trscv is in Fault state <Condtype> CFP_FAULT <Pro… |
| 1.3.6.1.4.1.20044.54.2.1.3.40.8 | Scalarrm10010mpAlmCfpTxTurnOff | read-only | current | Client Trscv Laser Turn Off :This OID indicates the Client Trscv is turning off its laser <Help> Status indicating the Client Trscv is turning off its laser <C… |
| 1.3.6.1.4.1.20044.54.2.1.3.40.9 | Scalarrm10010mpAlmCfpHighPowerDown | read-only | current | Client Trscv High Power Down :This OID indicates the Client Trscv is entering Low Power state <Help> Status indicating the Client Trscv is entering Low Power s… |
| 1.3.6.1.4.1.20044.54.2.1.3.41 | Noderm10010mpAlmclientModuleGeneralStatus | |||
| 1.3.6.1.4.1.20044.54.2.1.3.41.4 | Scalarrm10010mpAlmCfpOutOfAlignment | read-only | current | Client Trscv Out Of Alignment :This OID indicates an Out of alignment on the Client Trscv Host Interface <Help> Alarm indicating an Out of alignment on the Cli… |
| 1.3.6.1.4.1.20044.54.2.1.3.41.5 | Scalarrm10010mpAlmCfpRxNetworkLol | read-only | current | Client Trscv Rx Network Loss Of Lock :This OID indicates of Loss of Lock is dected on the Client Trscv Rx Network interface <Help> Alarm indicating of Loss of … |
| 1.3.6.1.4.1.20044.54.2.1.3.41.6 | Scalarrm10010mpAlmCfpRxLos | read-only | current | Client Trscv Loss Of Signal :This OID indicates a Loss of Signal is detected on the Client Trscv <Help> Alarm indicating a Loss of Signal is detected on the Cl… |
| 1.3.6.1.4.1.20044.54.2.1.3.41.7 | Scalarrm10010mpAlmCfpTxHostLol | read-only | current | Client Trscv Tx Host Loss Of Lock :This OID indicates of Loss of Lock is detected on the Client Trscv Tx Host interface <Help> Alarm indicating of Loss of Lock… |
| 1.3.6.1.4.1.20044.54.2.1.3.41.8 | Scalarrm10010mpAlmCfpTxLosf | read-only | current | Client Trscv Loss Of Signal Functionality :This OID indicates a Loss of Signal functionality is detected on the Client Trscv <Help> Alarm indicating a Loss of … |
| 1.3.6.1.4.1.20044.54.2.1.3.41.9 | Scalarrm10010mpAlmCfpTxCmuLol | read-only | current | Client Trscv CMU Loss Of Lock :This OID indicates a Clock Multiplier Unit Loss of Lock is detected on the Client Trscv <Help> Alarm indicating a Clock Multipli… |
| 1.3.6.1.4.1.20044.54.2.1.3.41.10 | Scalarrm10010mpAlmCfpTxJitterPllLol | read-only | current | Client Trscv Tx Jitter PLL Loss Of Lock :This OID indicates a Tx Jitter PLL Loss of Lock is dtected on the Client Trscv <Help> Alarm indicating a Tx Jitter PLL… |
| 1.3.6.1.4.1.20044.54.2.1.3.41.11 | Scalarrm10010mpAlmCfpLossOfRefclk | read-only | current | Client Trscv Loss Of Ref Clock :This OID indicates a Loss of Reference clock is detected on the Client Trscv <Help> Alarm indicating a Loss of Reference clock … |
| 1.3.6.1.4.1.20044.54.2.1.3.41.14 | Scalarrm10010mpAlmCfpHwInterlock | read-only | current | Client Trscv Hardware Interlock :This OID indicates the Client Trscv power is higher than the cooling capacity <Help> Alarm indicating the Client Trscv power i… |
| 1.3.6.1.4.1.20044.54.2.1.3.42 | Noderm10010mpAlmclientGlobalAlarmSummary | |||
| 1.3.6.1.4.1.20044.54.2.1.3.42.1 | Scalarrm10010mpAlmCfpSoftGlobAlarmTest | read-only | current | Client Trscv Global Alarm SW Test :This OID indicates the Client Trscv Global Alarm This OID is raised by SW request for test purpose <Help> Status indicating … |
| 1.3.6.1.4.1.20044.54.2.1.3.42.7 | Scalarrm10010mpAlmCfpNetworkLaneAlarmWarning2 | read-only | current | Client Trscv Network Alarm And Warning 2 :This OID indicates at least one DDM is detected on the Client Trscv Network Interface <Help> Synthesis alarm indicati… |
| 1.3.6.1.4.1.20044.54.2.1.3.42.8 | Scalarrm10010mpAlmCfpModuleState | read-only | current | Client Trscv Module State :This OID indicates the Client Trscv module state <Help> Synthesis alarm indicating the Client Trscv module state <Condtype> CFP_MODU… |
| 1.3.6.1.4.1.20044.54.2.1.3.42.9 | Scalarrm10010mpAlmCfpModuleGeneralStatus | read-only | current | Client Trscv General Status :This OID indicates the Client Trscv module general status <Help> Synthesis alarm indicating the Client Trscv module general status… |
| 1.3.6.1.4.1.20044.54.2.1.3.42.10 | Scalarrm10010mpAlmCfpModuleFault | read-only | current | Client Trscv Module Fault :This OID indicates at least one Fault is detected on the Client Trscv module <Help> Synthesis alarm indicating at least one Fault is… |
| 1.3.6.1.4.1.20044.54.2.1.3.42.11 | Scalarrm10010mpAlmCfpModuleAlarmWarning1 | read-only | current | Client Trscv Module Alarm And Warning 1 :This OID indicates at least one DDM This OID is detected on the Client Trscv module <Help> Synthesis alarm indicating … |
| 1.3.6.1.4.1.20044.54.2.1.3.42.12 | Scalarrm10010mpAlmCfpModuleAlarmWarning2 | read-only | current | Client Trscv Module Alarm And Warning 2 :This OID indicates at least one DDM is detected on the Client Trscv module <Help> Synthesis alarm indicating at least … |
| 1.3.6.1.4.1.20044.54.2.1.3.42.13 | Scalarrm10010mpAlmCfpNetworkLaneAlarmWarning1 | read-only | current | Client Trscv Network Alarm And Warning 1 :This OID indicates at least one DDM is detected on the Client Trscv Network Interface <Help> Synthesis alarm indicati… |
| 1.3.6.1.4.1.20044.54.2.1.3.42.14 | Scalarrm10010mpAlmCfpNetworkLaneFaultStatus | read-only | current | Client Trscv Network Fault And Status :This OID indicates at least one Fault or Status is detected on the Client Trscv Network Interface <Help> Synthesis alarm… |
| 1.3.6.1.4.1.20044.54.2.1.3.42.15 | Scalarrm10010mpAlmCfpHostLaneFaultStatus | read-only | current | Client Trscv Host Fault And Status :This OID indicates at least one Fault or Status is detected on the Client Trscv Host Interface <Help> Synthesis alarm indic… |
| 1.3.6.1.4.1.20044.54.2.1.3.42.16 | Scalarrm10010mpAlmCfpGlobAlarmAssertion | read-only | current | Client Trscv Global Alarm :This OID indicates at least one Fault or Status is detected on the Client Trscv module <Help> Synthesis alarm indicating at least on… |
| 1.3.6.1.4.1.20044.54.2.1.3.46 | Noderm10010mpAlmmsaModuleState | |||
| 1.3.6.1.4.1.20044.54.2.1.3.46.1 | Scalarrm10010mpAlmMsaInitialize | read-only | current | Line Trscv Initialize :This OID indicates the Line Trscv initialization is in progress <Help> Status indicating the Line Trscv initialization is in progress <C… |
| 1.3.6.1.4.1.20044.54.2.1.3.46.2 | Scalarrm10010mpAlmMsaLowPower | read-only | current | Line Trscv Low Power :This OID indicates the Line Trscv is in low power state <Help> Status indicating the Line Trscv is in low power state <Condtype> MSA_LOW_… |
| 1.3.6.1.4.1.20044.54.2.1.3.46.3 | Scalarrm10010mpAlmMsaHighPowerUp | read-only | current | Line Trscv High Power Up :This OID indicates the Line Trscv is leaving Low Power state <Help> Status indicating the Line Trscv is leaving Low Power state <Cond… |
| 1.3.6.1.4.1.20044.54.2.1.3.46.4 | Scalarrm10010mpAlmMsaTxOff | read-only | current | Line Trscv Laser Shutdown :This OID indicates the Line Trscv Laser is OFF <Help> Status indicating the Line Trscv Laser is OFF <Condtype> MSA_TX_OFF <Probcause… |
| 1.3.6.1.4.1.20044.54.2.1.3.46.5 | Scalarrm10010mpAlmMsaTxTurnOn | read-only | current | Line Trscv Laser Turn On :This OID indicates the Line Trscv is turning on its laser <Help> Status indicating the Line Trscv is turning on its laser <Condtype> … |
| 1.3.6.1.4.1.20044.54.2.1.3.46.6 | Scalarrm10010mpAlmMsaReady | read-only | current | Line Trscv Ready :This OID indicates the Line Trscv is ready to operate <Help> Status indicating the Line Trscv is ready to operate <Condtype> MSA_READY <Probc… |
| 1.3.6.1.4.1.20044.54.2.1.3.46.7 | Scalarrm10010mpAlmMsaFault | read-only | current | Line Trscv Fault :This OID indicates the Line Trscv is in Fault state <Help> Status indicating the Line Trscv is in Fault state <Condtype> MSA_FAULT <Probcause… |
| 1.3.6.1.4.1.20044.54.2.1.3.46.8 | Scalarrm10010mpAlmMsaTxTurnOff | read-only | current | Line Trscv Laser Turn Off :This OID indicates the Line Trscv is turning off its laser <Help> Status indicating the Line Trscv is turning off its laser <Condtyp… |
| 1.3.6.1.4.1.20044.54.2.1.3.46.9 | Scalarrm10010mpAlmMsaHighPowerDown | read-only | current | Line Trscv High Power Down :This OID indicates the Line Trscv is entering Low Power state <Help> Status indicating the Line Trscv is entering Low Power state <… |
| 1.3.6.1.4.1.20044.54.2.1.3.47 | Noderm10010mpAlmmsaModuleGeneralStatus | |||
| 1.3.6.1.4.1.20044.54.2.1.3.47.4 | Scalarrm10010mpAlmMsaOutOfAlignment | read-only | current | Line Trscv Out Of Alignment :This OID indicates an Out of alignment on the Line Trscv Host Interface <Help> Alarm indicating an Out of alignment on the Line Tr… |
| 1.3.6.1.4.1.20044.54.2.1.3.47.5 | Scalarrm10010mpAlmMsaRxNetworkLol | read-only | current | Line Trscv Rx Network Loss Of Lock :This OID indicates of Loss of Lock is detected on the Line Trscv Rx Network interface <Help> Alarm indicating of Loss of Lo… |
| 1.3.6.1.4.1.20044.54.2.1.3.47.6 | Scalarrm10010mpAlmMsaRxLos | read-only | current | Line Trscv Loss Of Signal :This OID indicates a Loss of Signal is detected on the Line Trscv <Help> Alarm indicating a Loss of Signal is detected on the Line T… |
| 1.3.6.1.4.1.20044.54.2.1.3.47.7 | Scalarrm10010mpAlmMsaTxHostLol | read-only | current | Line Trscv Tx Host Loss Of Lock :This OID indicates of Loss of Lock is detected on the Line Trscv Tx Host interface <Help> Alarm indicating of Loss of Lock is … |
| 1.3.6.1.4.1.20044.54.2.1.3.47.8 | Scalarrm10010mpAlmMsaTxLosf | read-only | current | Line Trscv Loss Of Signal Functionality :This OID indicates a Loss of Signal functionality is detected on the Line Trscv <Help> Alarm indicating a Loss of Sign… |
| 1.3.6.1.4.1.20044.54.2.1.3.47.9 | Scalarrm10010mpAlmMsaTxCmuLol | read-only | current | Line Trscv CMU Loss Of Lock :This OID indicates a Clock Multiplier Unit Loss of Lock is detected on the Line Trscv <Help> Alarm indicating a Clock Multiplier U… |
| 1.3.6.1.4.1.20044.54.2.1.3.47.10 | Scalarrm10010mpAlmMsaTxJitterPllLol | read-only | current | Line Trscv Tx Jitter PLL Loss Of Lock :This OID indicates a Tx Jitter PLL Loss of Lock is detected on the Line Trscv <Help> Alarm indicating a Tx Jitter PLL Lo… |
| 1.3.6.1.4.1.20044.54.2.1.3.47.11 | Scalarrm10010mpAlmMsaLossOfRefclk | read-only | current | Line Trscv Loss Of Ref Clock :This OID indicates a Loss of Reference clock is detected on the Line Trscv <Help> Alarm indicating a Loss of Reference clock is d… |
| 1.3.6.1.4.1.20044.54.2.1.3.47.14 | Scalarrm10010mpAlmMsaHwInterlock | read-only | current | Line Trscv Hardware Interlock :This OID indicates the Line Trscv power is higher than the cooling capacity <Help> Alarm indicating the Line Trscv power is high… |
| 1.3.6.1.4.1.20044.54.2.1.3.48 | Noderm10010mpAlmmsaGlobalAlarmSummary | |||
| 1.3.6.1.4.1.20044.54.2.1.3.48.1 | Scalarrm10010mpAlmMsaSoftGlobAlarmTest | read-only | current | Line Trscv Global Alarm SW Test :This OID indicates the Line Trscv Global alarm This OID is raised by SW request for test purpose <Help> Status indicating the … |
| 1.3.6.1.4.1.20044.54.2.1.3.48.6 | Scalarrm10010mpAlmMsaNetworkHostAlarmStatus | read-only | current | Line Trscv Network/Host Alarm Status :This OID indicates the state of the Network and Host interface of the Line Trscv <Help> Synthesis alarm indicating the al… |
| 1.3.6.1.4.1.20044.54.2.1.3.48.7 | Scalarrm10010mpAlmMsaNetworkLaneAlarmWarning2 | read-only | current | Line Trscv Network Alarm And Warning 2 :This OID indicates at least one DDM This OID is detected on the Line Trscv Network Interface <Help> Synthesis alarm ind… |
| 1.3.6.1.4.1.20044.54.2.1.3.48.8 | Scalarrm10010mpAlmMsaModuleState | read-only | current | Line Trscv Module State :This OID indicates the Line Trscv module state <Help> Synthesis alarm indicating the Line Trscv module state <Condtype> MSA_MODULE_STA… |
| 1.3.6.1.4.1.20044.54.2.1.3.48.9 | Scalarrm10010mpAlmMsaModuleGeneralStatus | read-only | current | Line Trscv General Status :This OID indicates the Line Trscv module general <Help> Synthesis alarm indicating the Line Trscv module general status <Condtype> M… |
| 1.3.6.1.4.1.20044.54.2.1.3.48.10 | Scalarrm10010mpAlmModuleFault | read-only | current | Line Trscv Module Fault :This OID indicates at least one Fault is detected on the Line Trscv module <Help> Synthesis alarm indicating at least one Fault is det… |
| 1.3.6.1.4.1.20044.54.2.1.3.48.11 | Scalarrm10010mpAlmMsaModuleAlarmWarning1 | read-only | current | Line Trscv Module Alarm And Warning 1 :This OID indicates at least one DDM is detected on the Line Trscv module <Help> Synthesis alarm indicating at least one … |
| 1.3.6.1.4.1.20044.54.2.1.3.48.12 | Scalarrm10010mpAlmMsaModuleAlarmWarning2 | read-only | current | Line Trscv Module Alarm And Warning 2 :This OID indicates at least one DDM is detected on the Line Trscv module <Help> Synthesis alarm indicating at least one … |
| 1.3.6.1.4.1.20044.54.2.1.3.48.13 | Scalarrm10010mpAlmMsaNetworkLaneAlarmWarning1 | read-only | current | Line Trscv Network Alarm And Warning 1 :This OID indicates at least one DDM is detected on the Line Trscv Network Interface <Help> Synthesis alarm indicating a… |
| 1.3.6.1.4.1.20044.54.2.1.3.48.14 | Scalarrm10010mpAlmMsaNetworkLaneFaultStatus | read-only | current | Line Trscv Network Fault And Status :This OID indicates at least one Fault or Status is detected on the Line Trscv Network Interface <Help> Synthesis alarm ind… |
| 1.3.6.1.4.1.20044.54.2.1.3.48.15 | Scalarrm10010mpAlmMsaHostLaneFaultStatus | read-only | current | Line Trscv Host Fault And Status :This OID indicates at least one Fault or Status is detected on the Line Trscv Host Interface <Help> Synthesis alarm indicatin… |
| 1.3.6.1.4.1.20044.54.2.1.3.48.16 | Scalarrm10010mpAlmMsaGlobAlarmAssertion | read-only | current | Line Trscv Global Alarm :This OID indicates at least one Fault or Status is detected on the Line Trscv module <Help> Synthesis alarm indicating at least one Al… |
| 1.3.6.1.4.1.20044.54.2.1.3.49 | Noderm10010mpAlmmsaNetworkTxAlignment | |||
| 1.3.6.1.4.1.20044.54.2.1.3.49.12 | Scalarrm10010mpAlmNetTxTimingFault | read-only | current | Line Trscv Network Tx Timing Fault :This OID indicates a Tx Timing Fault is detected on the Line Trscv Network interface <Help> Alarm indicating a Tx Timing Fa… |
| 1.3.6.1.4.1.20044.54.2.1.3.49.13 | Scalarrm10010mpAlmNetTxReferenceClockFault | read-only | current | Line Trscv Network Tx Ref Clock Fault :This OID indicates a Tx Reference Clock Fault is detected on the Line Trscv Network interface <Help> Alarm indicating a … |
| 1.3.6.1.4.1.20044.54.2.1.3.49.14 | Scalarrm10010mpAlmNetTxCmuLockFault | read-only | current | Line Trscv Network Tx CMU Lock Fault :This OID indicates a Tx Clock Multiplier Unit Lock Fault is detected on the Line Trscv Network interface <Help> Alarm ind… |
| 1.3.6.1.4.1.20044.54.2.1.3.49.15 | Scalarrm10010mpAlmNetTxOutOfAlignment | read-only | current | Line Trscv Network Tx Out Of Alignment :This OID indicates a Tx Out of Alignment is detected on the Line Trscv Network interface <Help> Alarm indicating a Tx O… |
| 1.3.6.1.4.1.20044.54.2.1.3.49.16 | Scalarrm10010mpAlmNetTxLossOfAlignment | read-only | current | Line Trscv Network Tx Loss Of Alignment :This OID indicates a Tx Loss of Alignment is detected on the Line Trscv Network interface <Help> Alarm indicating a Tx… |
| 1.3.6.1.4.1.20044.54.2.1.3.50 | Noderm10010mpAlmmsaNetworkRxAlignment | |||
| 1.3.6.1.4.1.20044.54.2.1.3.50.12 | Scalarrm10010mpAlmNetRxTimingFault | read-only | current | Line Trscv Network Rx Timing Fault :This OID indicates a Rx Timing Fault is detected on the Line Trscv Network interface <Help> Alarm indicating a Rx Timing Fa… |
| 1.3.6.1.4.1.20044.54.2.1.3.50.13 | Scalarrm10010mpAlmNetRxOutOfAlignment | read-only | current | Line Trscv Network Rx Out Of Alignment :This OID indicates a Rx Out of Alignment is detected on the Line Trscv Network interface <Help> Alarm indicating a Rx O… |
| 1.3.6.1.4.1.20044.54.2.1.3.50.14 | Scalarrm10010mpAlmNetRxLossOfAlignment | read-only | current | Line Trscv Network Rx Loss Of Alignment :This OID indicates a Rx Loss of Alignment is detected on the Line Trscv Network interface <Help> Alarm indicating a Rx… |
| 1.3.6.1.4.1.20044.54.2.1.3.50.15 | Scalarrm10010mpAlmNetRxModemLockFault | read-only | current | Line Trscv Network Rx Modem Lock Fault :This OID indicates a Rx Modem Lock Fault is detected on the Line Trscv Network interface <Help> Alarm indicating a Rx M… |
| 1.3.6.1.4.1.20044.54.2.1.3.50.16 | Scalarrm10010mpAlmNetRxModemSyncDetectFault | read-only | current | Line Trscv Network Rx Modem Sync Detect Fault :This OID indicates a Rx Modem Synchronisation Detection Fault is detected on the Line Trscv Network interface <H… |
| 1.3.6.1.4.1.20044.54.2.1.3.51 | Noderm10010mpAlmmsaNetworkHostNetworkAlarmSummary | |||
| 1.3.6.1.4.1.20044.54.2.1.3.51.11 | Scalarrm10010mpAlmNetworkTxAlignment | read-only | current | Line Trscv Network Tx Alignment :This OID indicates a Tx Alignment Fault is detected on the Line Trscv Network interface <Help> Synthesis Alarm indicating a Tx… |
| 1.3.6.1.4.1.20044.54.2.1.3.51.12 | Scalarrm10010mpAlmNetworkRxAlignment | read-only | current | Line Trscv Network Rx Alignment :This OID indicates a Rx Alignment Fault is detected on the Line Trscv Network interface <Help> Synthesis Alarm indicating a Rx… |
| 1.3.6.1.4.1.20044.54.2.1.3.51.13 | Scalarrm10010mpAlmNetworkRxOtn | read-only | current | Line Trscv Network Rx OTN :This OID indicates a Rx OTN Fault is detected on the Line Trscv Network interface <Help> Synthesis Alarm indicating a Rx OTN Fault i… |
| 1.3.6.1.4.1.20044.54.2.1.3.51.14 | Scalarrm10010mpAlmHostRxAlignment | read-only | current | Line Trscv Host Rx Alignment :This OID indicates a Rx Alignment Fault is detected on the Line Trscv Host interface <Help> Synthesis Alarm indicating a Rx Align… |
| 1.3.6.1.4.1.20044.54.2.1.3.51.15 | Scalarrm10010mpAlmHostTxAlignment | read-only | current | Line Trscv Host Tx Alignment :This OID indicates a Tx Alignment Fault is detected on the Line Trscv Host interface <Help> Synthesis Alarm indicating a Tx Align… |
| 1.3.6.1.4.1.20044.54.2.1.3.51.16 | Scalarrm10010mpAlmHostTxOtnStatus | read-only | current | Line Trscv Host Tx OTN :This OID indicates a Tx OTN Fault is detected on the Line Trscv Host interface <Help> Synthesis Alarm indicating a Tx OTN Fault is dete… |
| 1.3.6.1.4.1.20044.54.2.1.3.52 | Noderm10010mpAlmmsaHostTxAlignment | |||
| 1.3.6.1.4.1.20044.54.2.1.3.52.13 | Scalarrm10010mpAlmHostTxDeskewLockFault | read-only | current | Line Trscv Host Tx Deskew Lock Fault :This OID indicates a Tx Deskew Lock Fault is detected on the Line Trscv Host interface <Help> Alarm indicating a Tx Deske… |
| 1.3.6.1.4.1.20044.54.2.1.3.52.14 | Scalarrm10010mpAlmHostTxOutOfAlignment | read-only | current | Line Trscv Host Tx Out Of Alignment :This OID indicates a Tx Out of Alignment is detected on the Line Trscv Host interface <Help> Alarm indicating a Tx Out of … |
| 1.3.6.1.4.1.20044.54.2.1.3.52.15 | Scalarrm10010mpAlmHostTxLossOfAlignment | read-only | current | Line Trscv Host Tx Loss Of Alignment :This OID indicates a Tx Loss of Alignment is detected on the Line Trscv Host interface <Help> Alarm indicating a Tx Loss … |
| 1.3.6.1.4.1.20044.54.2.1.3.52.16 | Scalarrm10010mpAlmHostTxCdrLockFault | read-only | current | Line Trscv Host Tx CDR Lock Fault :This OID indicates a Tx Clock Data Recovery Lock Fault is detected on the Line Trscv Host interface <Help> Alarm indicating … |
| 1.3.6.1.4.1.20044.54.2.1.3.53 | Noderm10010mpAlmmsaHostRxAlignment | |||
| 1.3.6.1.4.1.20044.54.2.1.3.53.14 | Scalarrm10010mpAlmHostRxCmuLockFault | read-only | current | Line Trscv Host Rx CMU Lock Fault :This OID indicates a Rx Clock Multiplier Unit Lock Fault is detected on the Line Trscv Host interface <Help> Alarm indicatin… |
| 1.3.6.1.4.1.20044.54.2.1.3.53.15 | Scalarrm10010mpAlmHostRxOutOfAlignment | read-only | current | Line Trscv Host Rx Out Of Alignment :This OID indicates a Rx Out of Alignment is detected on the Line Trscv Host interface <Help> Alarm indicating a Rx Out of … |
| 1.3.6.1.4.1.20044.54.2.1.3.53.16 | Scalarrm10010mpAlmHostRxLossOfAlignment | read-only | current | Line Trscv Host Rx Loss Of Alignment :This OID indicates a Rx Loss of Alignment is detected on the Line Trscv Host interface <Help> Alarm indicating a Rx Loss … |
| 1.3.6.1.4.1.20044.54.2.2 | Noderm10010mpAlmClient | |||
| 1.3.6.1.4.1.20044.54.2.2.1 | Noderm10010mpAlmClientNurg | |||
| 1.3.6.1.4.1.20044.54.2.2.1.56 | Tablerm10010mpAlmclientNetworkLaneAlarmWarningTable | not-accessible | current | List of rm10010mpAlmclientNetworkLaneAlarmWarning Article |
| 1.3.6.1.4.1.20044.54.2.2.1.56.1 | Rowrm10010mpAlmclientNetworkLaneAlarmWarningEntry | not-accessible | current | Row definition for the rm10010mpAlmclientNetworkLaneAlarmWarning table |
| 1.3.6.1.4.1.20044.54.2.2.1.56.1.1 | Columnrm10010mpAlmclientNetworkLaneAlarmWarningIndex | read-only | current | Index definition for the rm10010mpAlmclientNetworkLaneAlarmWarning table |
| 1.3.6.1.4.1.20044.54.2.2.1.56.1.2 | Columnrm10010mpAlmClientRxPowerLowAlarmPortn | read-only | current | Client Trscv Rx Power Low Alarm :This OID indicates that the Trscv input power is lower than the threshold value written in the Trscv EEPROM <Help> Alarm indic… |
| 1.3.6.1.4.1.20044.54.2.2.1.56.1.3 | Columnrm10010mpAlmClientRxPowerLowWarningPortn | read-only | current | Client Trscv Rx Power Low Warning :This OID indicates that the Trscv input power is lower than the threshold value written in the Trscv EEPROM <Help> Warning i… |
| 1.3.6.1.4.1.20044.54.2.2.1.56.1.4 | Columnrm10010mpAlmClientRxPowerHighWarningPortn | read-only | current | Client Trscv Rx Power High Warning :This OID indicates that the Trscv input power is higher than the threshold value written in the Trscv EEPROM <Help> Warning… |
| 1.3.6.1.4.1.20044.54.2.2.1.56.1.5 | Columnrm10010mpAlmClientRxPowerHighAlarmPortn | read-only | current | Client Trscv Rx Power High Alarm :This OID indicates that the Trscv input power is higher than the threshold value written in the Trscv EEPROM <Help> Alarm ind… |
| 1.3.6.1.4.1.20044.54.2.2.1.56.1.6 | Columnrm10010mpAlmLaserTempLowAlarmPortn | read-only | current | Client Trscv Laser Temp Low Alarm :This OID indicates that the Trscv Laser Temperature is lower than the threshold value written in the Trscv EEPROM <Help> Ala… |
| 1.3.6.1.4.1.20044.54.2.2.1.56.1.7 | Columnrm10010mpAlmClientLaserTempLowWarningPortn | read-only | current | Client Trscv Laser Temp Low Warning :This OID indicates that the Trscv Laser Temperature is lower than the threshold value written in the Trscv EEPROM <Help> W… |
| 1.3.6.1.4.1.20044.54.2.2.1.56.1.8 | Columnrm10010mpAlmClientLaserTempHighWarningPortn | read-only | current | Client Trscv Laser Temp High Warning :This OID indicates that the Trscv Laser Temperature is higher than the threshold value written in the Trscv EEPROM <Help>… |
| 1.3.6.1.4.1.20044.54.2.2.1.56.1.9 | Columnrm10010mpAlmClientLaserTempHighAlarmPortn | read-only | current | Client Trscv Laser Temp High Alarm :This OID indicates that the Trscv Laser Temperature is higher than the threshold value written in the Trscv EEPROM <Help> A… |
| 1.3.6.1.4.1.20044.54.2.2.1.56.1.10 | Columnrm10010mpAlmClientTxPowerLowAlarmPortn | read-only | current | Client Trscv Tx Power Low Alarm :This OID indicates that the Trscv output power is lower than the threshold value written in the Trscv EEPROM <Help> Alarm indi… |
| 1.3.6.1.4.1.20044.54.2.2.1.56.1.11 | Columnrm10010mpAlmClientTxPowerLowWarningPortn | read-only | current | Client Trscv Tx Power Low Warning :This OID indicates that the Trscv output power is lower than the threshold value written in the Trscv EEPROM <Help> Warning … |
| 1.3.6.1.4.1.20044.54.2.2.1.56.1.12 | Columnrm10010mpAlmClientTxPowerHighWarningPortn | read-only | current | Client Trscv Tx Power High Warning :This OID indicates that the Trscv output power is higher than the threshold value written in the Trscv EEPROM <Help> Warnin… |
| 1.3.6.1.4.1.20044.54.2.2.1.56.1.13 | Columnrm10010mpAlmClientTxPowerHighAlarmPortn | read-only | current | Client Trscv Tx Power High Alarm :This OID indicates that the Trscv output power is higher than the threshold value written in the Trscv EEPROM <Help> Alarm in… |
| 1.3.6.1.4.1.20044.54.2.2.1.56.1.14 | Columnrm10010mpAlmClientBiasLowAlarmPortn | read-only | current | Client Trscv Bias Low Alarm :This OID indicates that the Trscv laser bias current is lower than the threshold value written in the Trscv EEPROM <Help> Alarm in… |
| 1.3.6.1.4.1.20044.54.2.2.1.56.1.15 | Columnrm10010mpAlmClientBiasLowWarningPortn | read-only | current | Client Trscv Bias Low Warning :This OID indicates that the Trscv laser bias current is lower than the threshold value written in the Trscv EEPROM <Help> Warnin… |
| 1.3.6.1.4.1.20044.54.2.2.1.56.1.16 | Columnrm10010mpAlmClientBiasHighWarningPortn | read-only | current | Client Trscv Bias High Warning :This OID indicates that the Trscv laser bias current is higher than the threshold value written in the Trscv EEPROM <Help> Warn… |
| 1.3.6.1.4.1.20044.54.2.2.1.56.1.17 | Columnrm10010mpAlmClientBiasHighAlarmPortn | read-only | current | Client Trscv Bias High Alarm :This OID indicates that the Trscv laser bias current is higher than the threshold value written in the Trscv EEPROM <Help> Alarm … |
| 1.3.6.1.4.1.20044.54.2.2.1.232 | Tablerm10010mpAlmclientSfpWarnDdmTable | not-accessible | current | List of rm10010mpAlmclientSfpWarnDdm Article |
| 1.3.6.1.4.1.20044.54.2.2.1.232.1 | Rowrm10010mpAlmclientSfpWarnDdmEntry | not-accessible | current | Row definition for the rm10010mpAlmclientSfpWarnDdm table |
| 1.3.6.1.4.1.20044.54.2.2.1.232.1.1 | Columnrm10010mpAlmclientSfpWarnDdmIndex | read-only | current | Index definition for the rm10010mpAlmclientSfpWarnDdm table |
| 1.3.6.1.4.1.20044.54.2.2.1.232.1.2 | Columnrm10010mpAlmTxPwLowWngPortn | read-only | current | Client Trscv Tx Power Low Warning :This OID indicates that the Trscv output power is lower than the threshold value written in the Trscv EEPROM <Help> Warning … |
| 1.3.6.1.4.1.20044.54.2.2.1.232.1.3 | Columnrm10010mpAlmTxPwrHighWngPortn | read-only | current | Client Trscv Tx Power High Warning :This OID indicates that the Trscv output power is higher than the threshold value written in the Trscv EEPROM <Help> Warnin… |
| 1.3.6.1.4.1.20044.54.2.2.1.232.1.4 | Columnrm10010mpAlmTxBiasLowWngPortn | read-only | current | Client Trscv Bias Low Warning :This OID indicates that the Trscv laser bias current is lower than the threshold value written in the Trscv EEPROM <Help> Warnin… |
| 1.3.6.1.4.1.20044.54.2.2.1.232.1.5 | Columnrm10010mpAlmTxBiasHighWngPortn | read-only | current | Client Trscv Bias High Warning :This OID indicates that the Trscv laser bias current is higher than the threshold value written in the Trscv EEPROM <Help> Warn… |
| 1.3.6.1.4.1.20044.54.2.2.1.232.1.6 | Columnrm10010mpAlmVccLowWngPortn | read-only | current | Client Trscv Power Supply Low Warning :This OID indicates that the Trscv power supply is lower than the threshold value written in the Trscv EEPROM <Help> Warn… |
| 1.3.6.1.4.1.20044.54.2.2.1.232.1.7 | Columnrm10010mpAlmVccHighWngPortn | read-only | current | Client Trscv Power Supply High Warning :This OID indicates that the Trscv power supply is higher than the threshold value written in the Trscv EEPROM <Help> Wa… |
| 1.3.6.1.4.1.20044.54.2.2.1.232.1.8 | Columnrm10010mpAlmTempLowWngPortn | read-only | current | Client Trscv Temp Low Warning :This OID indicates that the Trscv temperature is lower than the threshold value written in the Trscv EEPROM <Help> Warning indic… |
| 1.3.6.1.4.1.20044.54.2.2.1.232.1.9 | Columnrm10010mpAlmTempHighWngPortn | read-only | current | Client Trscv Temp High Warning :This OID indicates that the Trscv temperature is higher than the threshold value written in the Trscv EEPROM <Help> Warning ind… |
| 1.3.6.1.4.1.20044.54.2.2.1.232.1.16 | Columnrm10010mpAlmRxPwrLowWngPortn | read-only | current | Client Trscv Rx Power Low Warning :This OID indicates that the Trscv input power is lower than the threshold value written in the Trscv EEPROM <Help> Warning i… |
| 1.3.6.1.4.1.20044.54.2.2.1.232.1.17 | Columnrm10010mpAlmRxPwrHighWngPortn | read-only | current | Client Trscv Rx Power High Warning :This OID indicates that the Trscv input power is higher than the threshold value written in the Trscv EEPROM <Help> Warning… |
| 1.3.6.1.4.1.20044.54.2.2.2 | Noderm10010mpAlmClientUrg | |||
| 1.3.6.1.4.1.20044.54.2.2.2.72 | Tablerm10010mpAlmclientNetworkLaneFaultTable | not-accessible | current | List of rm10010mpAlmclientNetworkLaneFault Article |
| 1.3.6.1.4.1.20044.54.2.2.2.72.1 | Rowrm10010mpAlmclientNetworkLaneFaultEntry | not-accessible | current | Row definition for the rm10010mpAlmclientNetworkLaneFault table |
| 1.3.6.1.4.1.20044.54.2.2.2.72.1.1 | Columnrm10010mpAlmclientNetworkLaneFaultIndex | read-only | current | Index definition for the rm10010mpAlmclientNetworkLaneFault table |
| 1.3.6.1.4.1.20044.54.2.2.2.72.1.4 | Columnrm10010mpAlmClientLaneRxFifoErrorPortn | read-only | current | Client Network Lane Rx FIFO Error :This OID indicates a Rx FIFO Error on the Client Trscv Network Lane <Help> Alarm indicating a Rx FIFO Error on the Client Tr… |
| 1.3.6.1.4.1.20044.54.2.2.2.72.1.5 | Columnrm10010mpAlmClientLaneRxLolPortn | read-only | current | Client Network Lane Rx Loss Of Lock :This OID indicates a Rx Loss of Lock on the Client Trscv Network Lane <Help> Alarm indicating a Rx Loss of Lock on the Cli… |
| 1.3.6.1.4.1.20044.54.2.2.2.72.1.6 | Columnrm10010mpAlmClientLaneRxLosPortn | read-only | current | Client Network Lane Rx Loss Of Signal :This OID indicates a Rx Loss of Signal on the Client Trscv Network Lane <Help> Alarm indicating a Rx Loss of Signal on t… |
| 1.3.6.1.4.1.20044.54.2.2.2.72.1.8 | Columnrm10010mpAlmClientLaneTxLolPortn | read-only | current | Client Network Lane Tx Loss Of Lock :This OID indicates a Tx Loss of Lock on the Client Trscv Network Lane <Help> Alarm indicating a Tx Loss of Lock on the Cli… |
| 1.3.6.1.4.1.20044.54.2.2.2.72.1.9 | Columnrm10010mpAlmClientLaneTxLosfPortn | read-only | current | Client Network Lane Tx Loss Of Signal Functionality :This OID indicates a Tx Loss of Signal Functionality on the Client Trscv Network Lane <Help> Alarm indicat… |
| 1.3.6.1.4.1.20044.54.2.2.2.72.1.15 | Columnrm10010mpAlmClientLaneApdPowerSupplyPortn | read-only | current | Client Network Lane APD Power Supply :This OID indicates an APD Power supply failure on the Client Trscv Network Lane <Help> Alarm indicating an APD Power supp… |
| 1.3.6.1.4.1.20044.54.2.2.2.72.1.16 | Columnrm10010mpAlmClientLaneWavelengthUnlockedPortn | read-only | current | Client Network Lane Wavelength Unlock :This OID indicates a Wavelength unlock on the Client Trscv Network Lane <Help> Alarm indicating a Wavelength unlock on t… |
| 1.3.6.1.4.1.20044.54.2.2.2.72.1.17 | Columnrm10010mpAlmClientLaneTecFaultPortn | read-only | current | Client Network Lane TEC Fault :This OID indicates a TEC Fault on the Client Trscv Network Lane <Help> Alarm indicating a TEC Fault on the Client Trscv Network … |
| 1.3.6.1.4.1.20044.54.2.2.2.88 | Tablerm10010mpAlmclientHostLaneFaultTable | not-accessible | current | List of rm10010mpAlmclientHostLaneFault Article |
| 1.3.6.1.4.1.20044.54.2.2.2.88.1 | Rowrm10010mpAlmclientHostLaneFaultEntry | not-accessible | current | Row definition for the rm10010mpAlmclientHostLaneFault table |
| 1.3.6.1.4.1.20044.54.2.2.2.88.1.1 | Columnrm10010mpAlmclientHostLaneFaultIndex | read-only | current | Index definition for the rm10010mpAlmclientHostLaneFault table |
| 1.3.6.1.4.1.20044.54.2.2.2.88.1.2 | Columnrm10010mpAlmClientLossOfSyncPortn | read-only | current | Client Frame Alignment Loss :This OID indicates the module is not aligned with the incoming Client signal <Help> Alarm indicating the module is not aligned wit… |
| 1.3.6.1.4.1.20044.54.2.2.2.88.1.3 | Columnrm10010mpAlmClientInputLossOfSigPortn | read-only | current | Client Input Loss Of Signal :This OID indicates a Loss of Signal is detected on the Client Trscv <Help> Alarm indicating a Loss of Signal is detected on the Cl… |
| 1.3.6.1.4.1.20044.54.2.2.2.88.1.4 | Columnrm10010mpAlmClientLanesMarkerUnlockPortn | read-only | current | Client Lanes Marker Unlock :This OID indicates the Client lanes marker alignment is not lock <Help> Alarm indicating the Client lanes marker alignment is not l… |
| 1.3.6.1.4.1.20044.54.2.2.2.88.1.5 | Columnrm10010mpAlmClientLanes6466UnlockPortn | read-only | current | Client Lanes 64/66b Unlock :This OID indicates the Client 64/66b decoder is not lock <Help> Alarm indicating the Client 64/66b decoder is not lock <Condtype> C… |
| 1.3.6.1.4.1.20044.54.2.2.2.88.1.6 | Columnrm10010mpAlmClientLanesNotAlignedPortn | read-only | current | Client Lanes Not Aligned :This OID indicates the Client lanes are not aligned <Help> Alarm indicating the Client lanes are not aligned <Condtype> CLIENT_LANES_… |
| 1.3.6.1.4.1.20044.54.2.2.2.88.1.7 | Columnrm10010mpAlmClientCsfDetectedPortn | read-only | current | Client Signal Fail Detected :This OID indicates that a CSF has been detected on client port in the downstream direction <Help> This alarm indicates if a Client… |
| 1.3.6.1.4.1.20044.54.2.2.2.88.1.10 | Columnrm10010mpAlmClientTxHostLolPortn | read-only | current | Client Host Lane Tx Loss Of Lock :This OID indicates a Tx Loss of Lock on the Client Trscv Host Lane <Help> Alarm indicating a Tx Loss of Lock on the Client Tr… |
| 1.3.6.1.4.1.20044.54.2.2.2.88.1.11 | Columnrm10010mpAlmClientLaneTxFifoErrorPortn | read-only | current | Client Host Lane Tx FIFO Error :This OID indicates a Tx FIFO Error on the Client Trscv Host Lane <Help> Alarm indicating a Tx FIFO Error on the Client Trscv Ho… |
| 1.3.6.1.4.1.20044.54.2.2.2.216 | Tablerm10010mpAlmclientSfpAlmDdmTable | not-accessible | current | List of rm10010mpAlmclientSfpAlmDdm Article |
| 1.3.6.1.4.1.20044.54.2.2.2.216.1 | Rowrm10010mpAlmclientSfpAlmDdmEntry | not-accessible | current | Row definition for the rm10010mpAlmclientSfpAlmDdm table |
| 1.3.6.1.4.1.20044.54.2.2.2.216.1.1 | Columnrm10010mpAlmclientSfpAlmDdmIndex | read-only | current | Index definition for the rm10010mpAlmclientSfpAlmDdm table |
| 1.3.6.1.4.1.20044.54.2.2.2.216.1.2 | Columnrm10010mpAlmTxPwrLowAlaPortn | read-only | current | Client Trscv Tx Power Low :This OID indicates that the Trscv output power of port is lower than the threshold value written in the Trscv EEPROM <Help> Alarm in… |
| 1.3.6.1.4.1.20044.54.2.2.2.216.1.3 | Columnrm10010mpAlmTxPwrHighAlaPortn | read-only | current | Client Trscv Tx Power High :This OID indicates that the Trscv output power of port is higher than the threshold value written in the Trscv EEPROM <Help> Alarm … |
| 1.3.6.1.4.1.20044.54.2.2.2.216.1.4 | Columnrm10010mpAlmTxBiasLowAlaPortn | read-only | current | Client Trscv Bias Low :This OID indicates that the Trscv laser bias current of port is lower than the threshold value written in the Trscv EEPROM <Help> Alarm … |
| 1.3.6.1.4.1.20044.54.2.2.2.216.1.5 | Columnrm10010mpAlmTxBiasHighAlaPortn | read-only | current | Client Trscv Bias High :This OID indicates that the Trscv laser bias current of port is higher than the threshold value written in the Trscv EEPROM <Help> Alar… |
| 1.3.6.1.4.1.20044.54.2.2.2.216.1.6 | Columnrm10010mpAlmVccLowAlaPortn | read-only | current | Client Trscv Power Supply Low :This OID indicates that the Trscv power supply of port is lower than the threshold value written in the Trscv EEPROM <Help> Alar… |
| 1.3.6.1.4.1.20044.54.2.2.2.216.1.7 | Columnrm10010mpAlmVccHighAlaPortn | read-only | current | Client Trscv Power Supply High :This OID indicates that the Trscv power supply of port is higher than the threshold value written in the Trscv EEPROM <Help> Al… |
| 1.3.6.1.4.1.20044.54.2.2.2.216.1.8 | Columnrm10010mpAlmTempLowAlaPortn | read-only | current | Client Trscv Temp Low :This OID indicates that the Trscv temperature of port is lower than the threshold value written in the Trscv EEPROM <Help> Alarm indicat… |
| 1.3.6.1.4.1.20044.54.2.2.2.216.1.9 | Columnrm10010mpAlmTempHighAlaPortn | read-only | current | Client Trscv Temp High :This OID indicates that the Trscv temperature of port is higher than the threshold value written in the Trscv EEPROM <Help> Alarm indic… |
| 1.3.6.1.4.1.20044.54.2.2.2.216.1.16 | Columnrm10010mpAlmRxPwrLowAlaPortn | read-only | current | Client Trscv Rx Power Low :This OID indicates that the Trscv input power of port is lower than the threshold value written in the Trscv EEPROM <Help> Alarm ind… |
| 1.3.6.1.4.1.20044.54.2.2.2.216.1.17 | Columnrm10010mpAlmRxPwrHighAlaPortn | read-only | current | Client Trscv Rx Power High :This OID indicates that the Trscv input power of port is higher than the threshold value written in the Trscv EEPROM <Help> Alarm i… |
| 1.3.6.1.4.1.20044.54.2.2.3 | Noderm10010mpAlmClientCrit | |||
| 1.3.6.1.4.1.20044.54.2.2.3.8 | Tablerm10010mpAlmsynthAlmPortTable | not-accessible | current | List of rm10010mpAlmsynthAlmPort Article |
| 1.3.6.1.4.1.20044.54.2.2.3.8.1 | Rowrm10010mpAlmsynthAlmPortEntry | not-accessible | current | Row definition for the rm10010mpAlmsynthAlmPort table |
| 1.3.6.1.4.1.20044.54.2.2.3.8.1.1 | Columnrm10010mpAlmsynthAlmPortIndex | read-only | current | Index definition for the rm10010mpAlmsynthAlmPort table |
| 1.3.6.1.4.1.20044.54.2.2.3.8.1.2 | Columnrm10010mpAlmSfpAbsentPortn | read-only | current | Client Optical Module Absent :This OID indicates that the Transceiver is not present in the client port. <Help> This alarm indicates if the client transceiver … |
| 1.3.6.1.4.1.20044.54.2.2.3.8.1.3 | Columnrm10010mpAlmDdmAbsentPortn | read-only | current | DDM Supported On Client Trscv :This OID indicates that the Client transceiver supports the Digital Diagnostic Monitoring function <Help> This status indicates … |
| 1.3.6.1.4.1.20044.54.2.2.3.8.1.5 | Columnrm10010mpAlmHwFailAccPortn | read-only | current | Client HW Fail :This OID indicates a failure on client port, most probably caused by a HW issue. <Help> This alarm indicates a failure on client port, most pro… |
| 1.3.6.1.4.1.20044.54.2.2.3.8.1.6 | Columnrm10010mpAlmDwLsdPortn | read-only | current | Client Trscv Laser Shutdown :This OID indicates the Client transceiver laser is shutdown <Help> This status indicates if the client transceiver laser is shutdo… |
| 1.3.6.1.4.1.20044.54.2.2.3.8.1.7 | Columnrm10010mpAlmClientLocalOosPortn | read-only | current | Local Client Port In Service :This OID indicates that the local Client port is In Service (1) or Out of Service (2) <Help> This status indicates if the local c… |
| 1.3.6.1.4.1.20044.54.2.2.3.8.1.8 | Columnrm10010mpAlmClientRemoteOosPortn | read-only | current | Remote Client Port In Service :This OID indicates that the remote Client port is In Service (1) or Out of Service (2) <Help> This status indicates if the remot… |
| 1.3.6.1.4.1.20044.54.2.2.3.8.1.9 | Columnrm10010mpAlmDwCaisPortn | read-only | current | Client AIS Inserted :This OID indicates a CAIS has been inserted on the output client port. <Help> This status indicates if a Client Alarm Indication Signal is… |
| 1.3.6.1.4.1.20044.54.2.2.3.8.1.10 | Columnrm10010mpAlmSfpDdmWarningPortn | read-only | current | Warning On Client Trscv DDM :This OID indicates a warning is being received from the Client Transceiver DDM <Help> This alarm indicates if a DDM Warning has be… |
| 1.3.6.1.4.1.20044.54.2.2.3.8.1.11 | Columnrm10010mpAlmSfpDdmAlmPortn | read-only | current | Alarm On Client Trscv DDM :This OID indicates an alarm is being received from the Client Transceiver DDM <Help> This alarm indicates if a DDM Alarm has been de… |
| 1.3.6.1.4.1.20044.54.2.2.3.8.1.13 | Columnrm10010mpAlmFailAccPortn | read-only | current | Client Access Fail :This OID indicates a failure on the Client port <Help> This alarm indicates a failure on the Client port <Condtype> FAIL_ACC_1 <Probcause> … |
| 1.3.6.1.4.1.20044.54.2.2.3.8.1.17 | Columnrm10010mpAlmUpCsfPortn | read-only | current | Client Signal Fail Inserted :This OID indicates a CSF has been inserted in the upstream client port. <Help> This status indicates if a Client Signal Fail is cu… |
| 1.3.6.1.4.1.20044.54.2.3 | Noderm10010mpAlmLine | |||
| 1.3.6.1.4.1.20044.54.2.3.1 | Noderm10010mpAlmLineNurg | |||
| 1.3.6.1.4.1.20044.54.2.3.1.104 | Tablerm10010mpAlmlineNetworkLaneAlarmWarning1Table | not-accessible | current | List of rm10010mpAlmlineNetworkLaneAlarmWarning1 Article |
| 1.3.6.1.4.1.20044.54.2.3.1.104.1 | Rowrm10010mpAlmlineNetworkLaneAlarmWarning1Entry | not-accessible | current | Row definition for the rm10010mpAlmlineNetworkLaneAlarmWarning1 table |
| 1.3.6.1.4.1.20044.54.2.3.1.104.1.1 | Columnrm10010mpAlmlineNetworkLaneAlarmWarning1Index | read-only | current | Index definition for the rm10010mpAlmlineNetworkLaneAlarmWarning1 table |
| 1.3.6.1.4.1.20044.54.2.3.1.104.1.2 | Columnrm10010mpAlmLineRxPowerLowAlarmPortn | read-only | current | Line Trscv Rx Power Low Alarm :This OID indicates that the Trscv input power is lower than the threshold value written in the Trscv EEPROM <Help> Alarm indicat… |
| 1.3.6.1.4.1.20044.54.2.3.1.104.1.3 | Columnrm10010mpAlmLineRxPowerLowWarningPortn | read-only | current | Line Trscv Rx Power Low Warning :This OID indicates that the Trscv input power is lower than the threshold value written in the Trscv EEPROM <Help> Warning ind… |
| 1.3.6.1.4.1.20044.54.2.3.1.104.1.4 | Columnrm10010mpAlmLineRxPowerHighWarningPortn | read-only | current | Line Trscv Rx Power High Warning :This OID indicates that the Trscv input power is higher than the threshold value written in the Trscv EEPROM <Help> Warning i… |
| 1.3.6.1.4.1.20044.54.2.3.1.104.1.5 | Columnrm10010mpAlmLineRxPowerHighAlarmPortn | read-only | current | Line Trscv Rx Power High Alarm :This OID indicates that the Trscv input power is higher than the threshold value written in the Trscv EEPROM <Help> Alarm indic… |
| 1.3.6.1.4.1.20044.54.2.3.1.104.1.6 | Columnrm10010mpAlmLineLaserTempLowAlarmPortn | read-only | current | Line Trscv Tx Laser Temp Low Alarm :This OID indicates that the Trscv Tx Laser Temperature is lower than the threshold value written in the Trscv EEPROM <Help>… |
| 1.3.6.1.4.1.20044.54.2.3.1.104.1.7 | Columnrm10010mpAlmLineLaserTempLowWarningPortn | read-only | current | Line Trscv Tx Laser Temp Low Warning :This OID indicates that the Trscv Tx Laser Temperature is lower than the threshold value written in the Trscv EEPROM <Hel… |
| 1.3.6.1.4.1.20044.54.2.3.1.104.1.8 | Columnrm10010mpAlmLineLaserTempHighWarningPortn | read-only | current | Line Trscv Tx Laser Temp High Warning :This OID indicates that the Trscv Tx Laser Temperature is higher than the threshold value written in the Trscv EEPROM <H… |
| 1.3.6.1.4.1.20044.54.2.3.1.104.1.9 | Columnrm10010mpAlmLineLaserTempHighAlarmPortn | read-only | current | Line Trscv Tx Laser Temp High Alarm :This OID indicates that the Trscv Tx Laser Temperature is higher than the threshold value written in the Trscv EEPROM <Hel… |
| 1.3.6.1.4.1.20044.54.2.3.1.104.1.10 | Columnrm10010mpAlmLineTxPowerLowAlarmPortn | read-only | current | Line Trscv Tx Power Low Alarm :This OID indicates that the Trscv output power is lower than the threshold value written in the Trscv EEPROM <Help> Alarm indica… |
| 1.3.6.1.4.1.20044.54.2.3.1.104.1.11 | Columnrm10010mpAlmLineTxPowerLowWarningPortn | read-only | current | Line Trscv Tx Power Low Warning :This OID indicates that the Trscv output power is lower than the threshold value written in the Trscv EEPROM <Help> Warning in… |
| 1.3.6.1.4.1.20044.54.2.3.1.104.1.12 | Columnrm10010mpAlmLineTxPowerHighWarningPortn | read-only | current | Line Trscv Tx Power High Warning :This OID indicates that the Trscv output power is higher than the threshold value written in the Trscv EEPROM <Help> Warning … |
| 1.3.6.1.4.1.20044.54.2.3.1.104.1.13 | Columnrm10010mpAlmLineTxPowerHighAlarmPortn | read-only | current | Line Trscv Tx Power High Alarm :This OID indicates that the Trscv output power is higher than the threshold value written in the Trscv EEPROM <Help> Alarm indi… |
| 1.3.6.1.4.1.20044.54.2.3.1.104.1.14 | Columnrm10010mpAlmLineBiasLowAlarmPortn | read-only | current | Line Trscv Tx Bias Low Alarm :This OID indicates that the Trscv laser bias current is lower than the threshold value written in the Trscv EEPROM <Help> Alarm i… |
| 1.3.6.1.4.1.20044.54.2.3.1.104.1.15 | Columnrm10010mpAlmLineBiasLowWarningPortn | read-only | current | Line Trscv Tx Bias Low Warning :This OID indicates that the Trscv laser bias current is lower than the threshold value written in the Trscv EEPROM <Help> Warni… |
| 1.3.6.1.4.1.20044.54.2.3.1.104.1.16 | Columnrm10010mpAlmLineBiasHighWarningPortn | read-only | current | Line Trscv Tx Bias High Warning :This OID indicates that the Trscv laser bias current is higher than the threshold value written in the Trscv EEPROM <Help> War… |
| 1.3.6.1.4.1.20044.54.2.3.1.104.1.17 | Columnrm10010mpAlmLineBiasHighAlarmPortn | read-only | current | Line Trscv Tx Bias High Alarm :This OID indicates that the Trscv laser bias current is higher than the threshold value written in the Trscv EEPROM <Help> Alarm… |
| 1.3.6.1.4.1.20044.54.2.3.1.120 | Tablerm10010mpAlmlineNetworkLaneAlarmWarning2Table | not-accessible | current | List of rm10010mpAlmlineNetworkLaneAlarmWarning2 Article |
| 1.3.6.1.4.1.20044.54.2.3.1.120.1 | Rowrm10010mpAlmlineNetworkLaneAlarmWarning2Entry | not-accessible | current | Row definition for the rm10010mpAlmlineNetworkLaneAlarmWarning2 table |
| 1.3.6.1.4.1.20044.54.2.3.1.120.1.1 | Columnrm10010mpAlmlineNetworkLaneAlarmWarning2Index | read-only | current | Index definition for the rm10010mpAlmlineNetworkLaneAlarmWarning2 table |
| 1.3.6.1.4.1.20044.54.2.3.1.120.1.2 | Columnrm10010mpAlmTxModulatorBiasLowAlarmPortn | read-only | current | Line Trscv Tx Modulator Bias Low Alarm :This OID indicates that the Trscv Tx modulator bias current is lower than the threshold value written in the Trscv EEPR… |
| 1.3.6.1.4.1.20044.54.2.3.1.120.1.3 | Columnrm10010mpAlmTxModulatorBiasLowWarningPortn | read-only | current | Line Trscv Tx Modulator Bias Low Warning :This OID indicates that the Trscv Tx modulator bias current is lower than the threshold value written in the Trscv EE… |
| 1.3.6.1.4.1.20044.54.2.3.1.120.1.4 | Columnrm10010mpAlmTxModulatorBiasHighWarningPortn | read-only | current | Line Trscv Tx Modulator Bias High Warning :This OID indicates that the Trscv Tx modulator bias current is higher than the threshold value written in the Trscv … |
| 1.3.6.1.4.1.20044.54.2.3.1.120.1.5 | Columnrm10010mpAlmTxModulatorBiasHighAlarmPortn | read-only | current | Line Trscv Tx Modulator Bias High Alarm :This OID indicates that the Trscv Tx modulator bias current is higher than the threshold value written in the Trscv EE… |
| 1.3.6.1.4.1.20044.54.2.3.1.120.1.6 | Columnrm10010mpAlmRxLaserTempLowAlarmPortn | read-only | current | Line Trscv Rx Laser Temp Low Alarm :This OID indicates that the Trscv Rx Laser Temperature is lower than the threshold value written in the Trscv EEPROM <Help>… |
| 1.3.6.1.4.1.20044.54.2.3.1.120.1.7 | Columnrm10010mpAlmRxLaserTempLowWarningPortn | read-only | current | Line Trscv Rx Laser Temp Low Warning :This OID indicates that the Trscv Rx Laser Temperature is lower than the threshold value written in the Trscv EEPROM <Hel… |
| 1.3.6.1.4.1.20044.54.2.3.1.120.1.8 | Columnrm10010mpAlmRxLaserTempHighWarningPortn | read-only | current | Line Trscv Rx Laser Temp High Warning :This OID indicates that the Trscv Rx Laser Temperature is higher than the threshold value written in the Trscv EEPROM <H… |
| 1.3.6.1.4.1.20044.54.2.3.1.120.1.9 | Columnrm10010mpAlmRxLaserTempHighAlarmPortn | read-only | current | Line Trscv Rx Laser Temp High Alarm :This OID indicates that the Trscv Rx Laser Temperature is higher than the threshold value written in the Trscv EEPROM <Hel… |
| 1.3.6.1.4.1.20044.54.2.3.1.120.1.10 | Columnrm10010mpAlmRxLaserOutputLowAlarmPortn | read-only | current | Line Trscv Rx Output Power Low Alarm :This OID indicates that the Trscv Rx output power is lower than the threshold value written in the Trscv EEPROM <Help> Al… |
| 1.3.6.1.4.1.20044.54.2.3.1.120.1.11 | Columnrm10010mpAlmRxLaserOutputLowWarningPortn | read-only | current | Line Trscv Rx Output Power Low Warning :This OID indicates that the Trscv Rx output power is lower than the threshold value written in the Trscv EEPROM <Help> … |
| 1.3.6.1.4.1.20044.54.2.3.1.120.1.12 | Columnrm10010mpAlmRxLaserOutputHighWarningPortn | read-only | current | Line Trscv Rx Output Power High Warning :This OID indicates that the Trscv Rx output power is higher than the threshold value written in the Trscv EEPROM <Help… |
| 1.3.6.1.4.1.20044.54.2.3.1.120.1.13 | Columnrm10010mpAlmRxLaserOutputHighAlarmPortn | read-only | current | Line Trscv Rx Output Power High Alarm :This OID indicates that the Trscv Rx output power is higher than the threshold value written in the Trscv EEPROM <Help> … |
| 1.3.6.1.4.1.20044.54.2.3.1.120.1.14 | Columnrm10010mpAlmRxLaserBiasLowAlarmPortn | read-only | current | Line Trscv Rx Bias Low Alarm :This OID indicates that the Trscv Rx laser bias current is lower than the threshold value written in the Trscv EEPROM <Help> Alar… |
| 1.3.6.1.4.1.20044.54.2.3.1.120.1.15 | Columnrm10010mpAlmRxLaserBiasLowWarningPortn | read-only | current | Line Trscv Rx Bias Low Warning :This OID indicates that the Trscv Rx laser bias current is lower than the threshold value written in the Trscv EEPROM <Help> Wa… |
| 1.3.6.1.4.1.20044.54.2.3.1.120.1.16 | Columnrm10010mpAlmRxLaserBiasHighWarningPortn | read-only | current | Line Trscv Rx Bias High Warning :This OID indicates that the Trscv Rx laser bias current is higher than the threshold value written in the Trscv EEPROM <Help> … |
| 1.3.6.1.4.1.20044.54.2.3.1.120.1.17 | Columnrm10010mpAlmRxLaserBiasHighAlarmPortn | read-only | current | Line Trscv Rx Bias High Alarm :This OID indicates that the Trscv Rx laser bias current is higher than the threshold value written in the Trscv EEPROM <Help> Al… |
| 1.3.6.1.4.1.20044.54.2.3.2 | Noderm10010mpAlmLineUrg | |||
| 1.3.6.1.4.1.20044.54.2.3.2.136 | Tablerm10010mpAlmlineNetworkLaneFaultTable | not-accessible | current | List of rm10010mpAlmlineNetworkLaneFault Article |
| 1.3.6.1.4.1.20044.54.2.3.2.136.1 | Rowrm10010mpAlmlineNetworkLaneFaultEntry | not-accessible | current | Row definition for the rm10010mpAlmlineNetworkLaneFault table |
| 1.3.6.1.4.1.20044.54.2.3.2.136.1.1 | Columnrm10010mpAlmlineNetworkLaneFaultIndex | read-only | current | Index definition for the rm10010mpAlmlineNetworkLaneFault table |
| 1.3.6.1.4.1.20044.54.2.3.2.136.1.3 | Columnrm10010mpAlmLineLaneRxTecFaultPortn | read-only | current | Line Network Lane Rx TEC Fault :This OID indicates a Rx TEC Fault on the Line Trscv Network Lane <Help> Alarm indicating a Rx TEC Fault on the Line Trscv Netwo… |
| 1.3.6.1.4.1.20044.54.2.3.2.136.1.4 | Columnrm10010mpAlmLineLaneRxFifoErrorPortn | read-only | current | Line Network Lane Rx FIFO Error :This OID indicates a Rx FIFO Error on the Line Trscv Network Lane <Help> Alarm indicating a Rx FIFO Error on the Line Trscv Ne… |
| 1.3.6.1.4.1.20044.54.2.3.2.136.1.5 | Columnrm10010mpAlmLineLaneRxLolPortn | read-only | current | Line Network Lane Rx Loss Of Lock :This OID indicates a Rx Loss of Lock on the Line Trscv Network Lane <Help> Alarm indicating a Rx Loss of Lock on the Line Tr… |
| 1.3.6.1.4.1.20044.54.2.3.2.136.1.6 | Columnrm10010mpAlmLineLaneRxLosPortn | read-only | current | Line Network Lane Rx Loss Of Signal :This OID indicates a Rx Loss of Signal on the Line Trscv Network Lane <Help> Alarm indicating a Rx Loss of Signal on the L… |
| 1.3.6.1.4.1.20044.54.2.3.2.136.1.8 | Columnrm10010mpAlmLineLaneTxLolPortn | read-only | current | Line Network Lane Tx Loss Of Lock :This OID indicates a Tx Loss of Lock on the Line Trscv Network Lane <Help> Alarm indicating a Tx Loss of Lock on the Line Tr… |
| 1.3.6.1.4.1.20044.54.2.3.2.136.1.9 | Columnrm10010mpAlmLineLaneTxLosfPortn | read-only | current | Line Network Lane Tx Loss Of Signal Functionality :This OID indicates a Tx Loss of Signal Functionality on the Line Trscv Network Lane <Help> Alarm indicating … |
| 1.3.6.1.4.1.20044.54.2.3.2.136.1.15 | Columnrm10010mpAlmLineLaneApdPowerSupplyPortn | read-only | current | Line Network Lane APD Power Supply :This OID indicates an APD Power supply failure on the Line Trscv Network Lane <Help> Alarm indicating an APD Power supply f… |
| 1.3.6.1.4.1.20044.54.2.3.2.136.1.16 | Columnrm10010mpAlmLineLaneWavelengthUnlockedPortn | read-only | current | Line Network Lane Wavelength Unlock :This OID indicates a Wavelength unlock on the Line Trscv Network Lane <Help> Alarm indicating a Wavelength unlock on the L… |
| 1.3.6.1.4.1.20044.54.2.3.2.136.1.17 | Columnrm10010mpAlmLineLaneTecFaultPortn | read-only | current | Line Network Lane TEC Fault :This OID indicates a Tx TEC Fault on the Line Trscv Network Lane <Help> Alarm indicating a Tx TEC Fault on the Line Trscv Network … |
| 1.3.6.1.4.1.20044.54.2.3.2.152 | Tablerm10010mpAlmlineHostLaneFaultTable | not-accessible | current | List of rm10010mpAlmlineHostLaneFault Article |
| 1.3.6.1.4.1.20044.54.2.3.2.152.1 | Rowrm10010mpAlmlineHostLaneFaultEntry | not-accessible | current | Row definition for the rm10010mpAlmlineHostLaneFault table |
| 1.3.6.1.4.1.20044.54.2.3.2.152.1.1 | Columnrm10010mpAlmlineHostLaneFaultIndex | read-only | current | Index definition for the rm10010mpAlmlineHostLaneFault table |
| 1.3.6.1.4.1.20044.54.2.3.2.152.1.2 | Columnrm10010mpAlmLineInputLossOfSignalPortn | read-only | current | Line Input Loss Of Signal :This OID indicates a Loss of Signal is detected on the Line Trscv <Help> Alarm indicating a Loss of Signal is detected on the Line T… |
| 1.3.6.1.4.1.20044.54.2.3.2.152.1.3 | Columnrm10010mpAlmLineLossOfFramePortn | read-only | current | Line Loss Of Frame :This OID indicates the module is not aligned with the incoming Line signal <Help> Alarm indicating the module is not aligned with the incom… |
| 1.3.6.1.4.1.20044.54.2.3.2.152.1.4 | Columnrm10010mpAlmLineSmBdiInsertedPortn | read-only | current | Line SM BDI Inserted :This OID indicates a SM Backward Defect Indication is inserted on the outgoing Line signal <Help> Status indicating a SM Backward Defect … |
| 1.3.6.1.4.1.20044.54.2.3.2.152.1.5 | Columnrm10010mpAlmLineSmBdiDetectedPortn | read-only | current | Line SM BDI Detected :This OID indicates a SM Backward Defect Indication is detected on the incoming Line signal <Help> Alarm indicating a SM Backward Defect I… |
| 1.3.6.1.4.1.20044.54.2.3.2.152.1.6 | Columnrm10010mpAlmLineSmIaeInsertedPortn | read-only | current | Line SM IAE Inserted :This OID indicates a SM Incoming Alignment Error is inserted on the outgoing Line signal <Help> Status indicating a SM Incoming Alignment… |
| 1.3.6.1.4.1.20044.54.2.3.2.152.1.7 | Columnrm10010mpAlmLineSmIaeDetectedPortn | read-only | current | Line SM IAE Detected :This OID indicates a SM Incoming Alignment Error is detected on the incoming Line signal <Help> Alarm indicating a SM Incoming Alignment … |
| 1.3.6.1.4.1.20044.54.2.3.2.152.1.10 | Columnrm10010mpAlmLineTxHostLolPortn | read-only | current | Line Host Lane Tx Loss Of Lock :This OID indicates a Tx Loss of Lock on the Line Trscv Host Lane <Help> Alarm indicating a Tx Loss of Lock on the Line Trscv Ho… |
| 1.3.6.1.4.1.20044.54.2.3.2.152.1.11 | Columnrm10010mpAlmLineLaneTxFifoErrorPortn | read-only | current | Line Host Lane Tx FIFO Error :This OID indicates a Tx FIFO Error on the Line Trscv Host Lane <Help> Alarm indicating a Tx FIFO Error on the Line Trscv Host Lan… |
| 1.3.6.1.4.1.20044.54.2.3.2.168 | Tablerm10010mpAlmlineNetworkLaneRxOtnTable | not-accessible | current | List of rm10010mpAlmlineNetworkLaneRxOtn Article |
| 1.3.6.1.4.1.20044.54.2.3.2.168.1 | Rowrm10010mpAlmlineNetworkLaneRxOtnEntry | not-accessible | current | Row definition for the rm10010mpAlmlineNetworkLaneRxOtn table |
| 1.3.6.1.4.1.20044.54.2.3.2.168.1.1 | Columnrm10010mpAlmlineNetworkLaneRxOtnIndex | read-only | current | Index definition for the rm10010mpAlmlineNetworkLaneRxOtn table |
| 1.3.6.1.4.1.20044.54.2.3.2.168.1.10 | Columnrm10010mpAlmLineRxOtnOduAisPortn | read-only | current | Line Network Rx ODU AIS :This OID indicates an ODU This OID Indication Signal is detected on the Rx Network interface of the Line Trscv <Help> Alarm indicating… |
| 1.3.6.1.4.1.20044.54.2.3.2.168.1.11 | Columnrm10010mpAlmLineRxOtnOtuAisPortn | read-only | current | Line Network Rx OTU AIS :This OID indicates an OTU This OID Indication Signal is detected on the Rx Network interface of the Line Trscv <Help> Alarm indicating… |
| 1.3.6.1.4.1.20044.54.2.3.2.168.1.12 | Columnrm10010mpAlmLineRxSmBdiPortn | read-only | current | Line Network Rx SM BDI :This OID indicates an SM Backward Defect Indication is detected on the Rx Network interface of the Line Trscv <Help> Alarm indicating a… |
| 1.3.6.1.4.1.20044.54.2.3.2.168.1.13 | Columnrm10010mpAlmLineRxOtnIaePortn | read-only | current | Line Network Rx IAE :This OID indicates an Incoming Alignment Error is detected on the Rx Network interface of the Line Trscv <Help> Alarm indicating an Incomi… |
| 1.3.6.1.4.1.20044.54.2.3.2.168.1.14 | Columnrm10010mpAlmLineRxOtnOomPortn | read-only | current | Line Network Rx OOM :This OID indicates an Out of Multiframe is detected on the Rx Network interface of the Line Trscv <Help> Alarm indicating an Out of Multif… |
| 1.3.6.1.4.1.20044.54.2.3.2.168.1.15 | Columnrm10010mpAlmLineRxOtnLomPortn | read-only | current | Line Network Rx LOM :This OID indicates a Loss of Multiframe is detected on the Rx Network interface of the Line Trscv <Help> Alarm indicating a Loss of Multif… |
| 1.3.6.1.4.1.20044.54.2.3.2.168.1.16 | Columnrm10010mpAlmLineRxOtnOofPortn | read-only | current | Line Network Rx OOF :This OID indicates an Out of Frame is detected on the Rx Network interface of the Line Trscv <Help> Alarm indicating an Out of Frame is de… |
| 1.3.6.1.4.1.20044.54.2.3.2.168.1.17 | Columnrm10010mpAlmLineRxOtnLofPortn | read-only | current | Line Network Rx LOF :This OID indicates a Loss of Frame is detected on the Rx Network interface of the Line Trscv <Help> Alarm indicating a Loss of Frame is de… |
| 1.3.6.1.4.1.20044.54.2.3.2.184 | Tablerm10010mpAlmlineHostLaneTxOtnTable | not-accessible | current | List of rm10010mpAlmlineHostLaneTxOtn Article |
| 1.3.6.1.4.1.20044.54.2.3.2.184.1 | Rowrm10010mpAlmlineHostLaneTxOtnEntry | not-accessible | current | Row definition for the rm10010mpAlmlineHostLaneTxOtn table |
| 1.3.6.1.4.1.20044.54.2.3.2.184.1.1 | Columnrm10010mpAlmlineHostLaneTxOtnIndex | read-only | current | Index definition for the rm10010mpAlmlineHostLaneTxOtn table |
| 1.3.6.1.4.1.20044.54.2.3.2.184.1.10 | Columnrm10010mpAlmLineTxOtnOduAisPortn | read-only | current | Line Host Tx ODU AIS :This OID indicates an ODU This OID Indication Signal is detected on the Tx Host interface of the Line Trscv <Help> Alarm indicating an OD… |
| 1.3.6.1.4.1.20044.54.2.3.2.184.1.11 | Columnrm10010mpAlmLineTxOtnOtuAisPortn | read-only | current | Line Host Tx OTU AIS :This OID indicates an OTU This OID Indication Signal is detected on the Tx Host interface of the Line Trscv <Help> Alarm indicating an OT… |
| 1.3.6.1.4.1.20044.54.2.3.2.184.1.12 | Columnrm10010mpAlmLineTxSmBdiPortn | read-only | current | Line Host Tx SM BDI :This OID indicates an SM Backward Defect Indication is detected on the Tx Host interface of the Line Trscv <Help> Alarm indicating an SM B… |
| 1.3.6.1.4.1.20044.54.2.3.2.184.1.13 | Columnrm10010mpAlmLineTxOtnIaePortn | read-only | current | Line Host Tx IAE :This OID indicates an Incoming Alignment Error is detected on the Tx Host interface of the Line Trscv <Help> Alarm indicating an Incoming Ali… |
| 1.3.6.1.4.1.20044.54.2.3.2.184.1.14 | Columnrm10010mpAlmLineTxOtnOomPortn | read-only | current | Line Host Tx OOM :This OID indicates an Out of Multiframe is detected on the Tx Host interface of the Line Trscv <Help> Alarm indicating an Out of Multiframe i… |
| 1.3.6.1.4.1.20044.54.2.3.2.184.1.15 | Columnrm10010mpAlmLineTxOtnLomPortn | read-only | current | Line Host Tx LOM :This OID indicates a Loss of Multiframe is detected on the Tx Host interface of the Line Trscv <Help> Alarm indicating a Loss of Multiframe i… |
| 1.3.6.1.4.1.20044.54.2.3.2.184.1.16 | Columnrm10010mpAlmLineTxOtnOofPortn | read-only | current | Line Host Tx OOF :This OID indicates an Out of Frame is detected on the Tx Host interface of the Line Trscv <Help> Alarm indicating an Out of Frame is detected… |
| 1.3.6.1.4.1.20044.54.2.3.2.184.1.17 | Columnrm10010mpAlmLineTxOtnLofPortn | read-only | current | Line Host Tx LOF :This OID indicates a Loss of Frame is detected on the Tx Host interface of the Line Trscv <Help> Alarm indicating a Loss of Frame is detected… |
| 1.3.6.1.4.1.20044.54.2.3.3 | Noderm10010mpAlmLineCrit | |||
| 1.3.6.1.4.1.20044.54.2.3.3.24 | Tablerm10010mpAlmsynthAlmLineTable | not-accessible | current | List of rm10010mpAlmsynthAlmLine Article |
| 1.3.6.1.4.1.20044.54.2.3.3.24.1 | Rowrm10010mpAlmsynthAlmLineEntry | not-accessible | current | Row definition for the rm10010mpAlmsynthAlmLine table |
| 1.3.6.1.4.1.20044.54.2.3.3.24.1.1 | Columnrm10010mpAlmsynthAlmLineIndex | read-only | current | Index definition for the rm10010mpAlmsynthAlmLine table |
| 1.3.6.1.4.1.20044.54.2.3.3.24.1.2 | Columnrm10010mpAlmXfpAbsentPortn | read-only | current | Line Optical Module Absent :This OID indicates that the line optical interface is not present. <Help> This alarm indicates if the line transceiver is not plugg… |
| 1.3.6.1.4.1.20044.54.2.3.3.24.1.3 | Columnrm10010mpAlmXfpInitNotComplPortn | read-only | current | Line Optical Module Ready :This OID indicates that the optical interface is not operational. <Help> This status indicates if the line transceiver has been corr… |
| 1.3.6.1.4.1.20044.54.2.3.3.24.1.5 | Columnrm10010mpAlmLineHwFailPortn | read-only | current | Line Port HW Failure :This OID indicates a failure on line port, most probably caused by a HW issue <Help> This alarm indicates a failure on line port, most pr… |
| 1.3.6.1.4.1.20044.54.2.3.3.24.1.6 | Columnrm10010mpAlmXfpTxOffPortn | read-only | current | Line Trscv Laser Shutdown :This OID indicates the Line transceiver laser is shutdown <Help> This status indicates if the Line transceiver laser is shutdown <Co… |
| 1.3.6.1.4.1.20044.54.2.3.3.24.1.7 | Columnrm10010mpAlmLineLocalOosPortn | read-only | current | Line Port In Service :This OID indicates that the Line port is In Service (1) of Out or Service (2) <Help> This status indicates if the line port is in service… |
| 1.3.6.1.4.1.20044.54.2.3.3.24.1.9 | Columnrm10010mpAlmUpRdiInsPortn | read-only | current | MS-RDI/L-RDI Inserted On Line :This OID indicates an upstream MS-RDI/L-RDI has been inserted in the outgoing 10 Gb/s SDH/SONET signal. <Help> This status indic… |
| 1.3.6.1.4.1.20044.54.2.3.3.24.1.10 | Columnrm10010mpAlmLineDdmWarningPortn | read-only | current | Warning On Line Optical Module DDM :This OID indicates a warning is present coming out of Line transceiver DDM <Help> This alarm indicates if a DDM Warning has… |
| 1.3.6.1.4.1.20044.54.2.3.3.24.1.11 | Columnrm10010mpAlmLineDdmAlmPortn | read-only | current | Alarm On Line Optical Module DDM :This OID indicates an alarm is present coming out of Line transceiver DDM <Help> This alarm indicates if a DDM Alarm has been… |
| 1.3.6.1.4.1.20044.54.2.3.3.24.1.13 | Columnrm10010mpAlmLineFailPortn | read-only | current | Line Port Failure :This OID indicates a failure on the line port <Help> This alarm indicates a failure on the line port <Condtype> LINE_FAIL <Probcause> equipm… |
| 1.3.6.1.4.1.20044.54.2.3.3.24.1.17 | Columnrm10010mpAlmLineActivePortn | read-only | current | Line Active :This OID indicates whether the line is active or standby. <Help> This status indicates whether the line is active or standby. <Condtype> LINE_ACTI… |
| 1.3.6.1.4.1.20044.54.3 | Noderm10010mpmeasures | |||
| 1.3.6.1.4.1.20044.54.3.1 | Noderm10010mpMesrOther | |||
| 1.3.6.1.4.1.20044.54.3.1.0 | Scalarrm10010mpMesrsynth0 | read-only | deprecated | Not Used : |
| 1.3.6.1.4.1.20044.54.3.1.1 | Scalarrm10010mpMesrsynth1 | read-only | deprecated | Not Used : |
| 1.3.6.1.4.1.20044.54.3.1.7 | Scalarrm10010mpMesrpmIntervalNumber | read-only | current | PM Interval Counter : |
| 1.3.6.1.4.1.20044.54.3.1.180 | Scalarrm10010mpMesrlineNetTxLaserOutputPwrAverage | read-only | current | Average Line Trscv Tx Power :This OID gives the average Tx Laser transmit power value among the network lanes of the Line Transceiver, read in the DDM (Digital… |
| 1.3.6.1.4.1.20044.54.3.1.181 | Scalarrm10010mpMesrlineNetTxLaserTempAverage | read-only | current | Average Line Trscv Tx Laser Temperature :This OID gives the average Tx Laser Temperature value among the network lanes of the Line Transceiver, read from the D… |
| 1.3.6.1.4.1.20044.54.3.1.182 | Scalarrm10010mpMesrlineNetTxBiasCurrentAverage | read-only | current | Average Line Trscv Tx Laser Bias :This OID gives the average Tx Laser Bias value among the network lanes of the Line Transceiver, read from the DDM (Digital Di… |
| 1.3.6.1.4.1.20044.54.3.1.183 | Scalarrm10010mpMesrlineNetRxInputPwrAverage | read-only | current | Average Line Trscv Rx Power :This OID gives the average Receive power value among the network lanes of the Line Transceiver, read in the DDM (Digital Diagnosti… |
| 1.3.6.1.4.1.20044.54.3.1.184 | Scalarrm10010mpMesrlineResidualChromaticDispAverage | read-only | current | Average Residual Chromatic Dispersion :This OID gives the average Residual Chromatic Dispersion on the Line interface since the last measure reset <Help> This … |
| 1.3.6.1.4.1.20044.54.3.1.185 | Scalarrm10010mpMesrlineDiffGroupDelayAverage | read-only | current | Average Differential Group Delay :This OID gives the average Group Delay on the Line interface since the last measure reset <Help> This measure gives the avera… |
| 1.3.6.1.4.1.20044.54.3.1.186 | Scalarrm10010mpMesrlineQFactorAverage | read-only | current | Average Q Factor :This OID gives the average Q Factor on the Line interface since the last measure reset <Help> This measure gives the average Q Factor on the … |
| 1.3.6.1.4.1.20044.54.3.1.187 | Scalarrm10010mpMesrlineCarrierFreqOffsetAverage | read-only | current | Average Carrier Frequency Offset :This OID gives the average Carrier Frequency Offset on the Line interface since the last measure reset <Help> This measure gi… |
| 1.3.6.1.4.1.20044.54.3.1.188 | Scalarrm10010mpMesrlineOsnrAverage | read-only | current | Average OSNR :This OID gives the average OSNR on the Line interface since the last measure reset <Help> This measure gives the average OSNR on the Line interfa… |
| 1.3.6.1.4.1.20044.54.3.1.192 | Scalarrm10010mpMesrclientNetTxTempMin | read-only | current | Min Client Trscv Laser Temperature :This OID gives the minimum Laser temperature value among the network lanes of the Client Transceiver, read from the DDM (Di… |
| 1.3.6.1.4.1.20044.54.3.1.193 | Scalarrm10010mpMesrclientNetTxBiasMin | read-only | current | Min Client Trscv Laser Bias :This OID gives the minimum Laser bias value among the network lanes of the Client Transceiver, read from the DDM (Digital Diagnost… |
| 1.3.6.1.4.1.20044.54.3.1.194 | Scalarrm10010mpMesrclientNetTxPwrMin | read-only | current | Min Client Trscv Tx Power :This OID gives the minimum transmit power value among the network lanes of the Client Transceiver, read from the DDM (Digital Diagno… |
| 1.3.6.1.4.1.20044.54.3.1.195 | Scalarrm10010mpMesrclientNetRxPwrMin | read-only | current | Min Client Trscv Rx Power :This OID gives the minimum receive power value among the network lanes of the Client Transceiver, read in the DDM (Digital Diagnosti… |
| 1.3.6.1.4.1.20044.54.3.1.196 | Scalarrm10010mpMesrlineNetTxLaserOutputPwrMin | read-only | current | Min Line Trscv Tx Power :This OID gives the minimum Tx Laser transmit power value among the network lanes of the Line Transceiver, read in the DDM (Digital Dia… |
| 1.3.6.1.4.1.20044.54.3.1.197 | Scalarrm10010mpMesrlineNetTxLaserTempMin | read-only | current | Min Line Trscv Tx Laser Temperature :This OID gives the minimum Tx Laser Temperature value among the network lanes of the Line Transceiver, read from the DDM (… |
| 1.3.6.1.4.1.20044.54.3.1.198 | Scalarrm10010mpMesrlineNetTxBiasCurrentMin | read-only | current | Min Line Trscv Tx Laser Bias :This OID gives the minimum Tx Laser Bias value among the network lanes of the Line Transceiver, read from the DDM (Digital Diagno… |
| 1.3.6.1.4.1.20044.54.3.1.199 | Scalarrm10010mpMesrlineNetRxInputPwrMin | read-only | current | Min Line Trscv Rx Power :This OID gives the minimum Receive power value among the network lanes of the Line Transceiver, read in the DDM (Digital Diagnostic Mo… |
| 1.3.6.1.4.1.20044.54.3.1.200 | Scalarrm10010mpMesrlineResidualChromaticDispMin | read-only | current | Min Residual Chromatic Dispersion :This OID gives the minimum Residual Chromatic Dispersion on the Line interface since the last measure reset (Unit = ps/nm)<H… |
| 1.3.6.1.4.1.20044.54.3.1.201 | Scalarrm10010mpMesrlineDiffGroupDelayMin | read-only | current | Min Differential Group Delay :This OID gives the minimum Differential Group Delay on the Line interface since the last measure reset (Unit = ps)<Help> This mea… |
| 1.3.6.1.4.1.20044.54.3.1.202 | Scalarrm10010mpMesrlineQFactorMin | read-only | current | Min Q Factor :This OID gives the minimum Q Factor on the Line interface since the last measure reset (Unit = dB)<Help> This measure gives the minimum Q Factor … |
| 1.3.6.1.4.1.20044.54.3.1.203 | Scalarrm10010mpMesrlineCarrierFreqOffsetMin | read-only | current | Min Carrier Frequency Offset :This OID gives the minimum Carrier Frequency Offset on the Line interface since the last measure reset (Unit = Mhz)<Help> This me… |
| 1.3.6.1.4.1.20044.54.3.1.204 | Scalarrm10010mpMesrlineOsnrMin | read-only | current | Min OSNR :This OID gives the minimum OSNR on the Line interface since the last measure reset (OSNR = AV/10) (Unit = dB)<Help> This measure gives the minimum OS… |
| 1.3.6.1.4.1.20044.54.3.1.208 | Scalarrm10010mpMesrclientNetTxTempMax | read-only | current | Max Client Trscv Laser Temperature :This OID gives the maximum Laser temperature value among the network lanes of the Client Transceiver, read from the DDM (Di… |
| 1.3.6.1.4.1.20044.54.3.1.209 | Scalarrm10010mpMesrclientNetTxBiasMax | read-only | current | Max Client Trscv Laser Bias :This OID gives the maximum Laser bias value among the network lanes of the Client Transceiver, read from the DDM (Digital Diagnost… |
| 1.3.6.1.4.1.20044.54.3.1.210 | Scalarrm10010mpMesrclientNetTxPwrMax | read-only | current | Max Client Trscv Tx Power :This OID gives the maximum transmit power value among the network lanes of the Client Transceiver, read from the DDM (Digital Diagno… |
| 1.3.6.1.4.1.20044.54.3.1.211 | Scalarrm10010mpMesrclientNetRxPwrMax | read-only | current | Max Client Trscv Rx Power :This OID gives the maximum receive power value among the network lanes of the Client Transceiver, read in the DDM (Digital Diagnosti… |
| 1.3.6.1.4.1.20044.54.3.1.212 | Scalarrm10010mpMesrlineNetTxLaserOutputPwrMax | read-only | current | Max Line Trscv Tx Power :This OID gives the maximum Tx Laser transmit power value among the network lanes of the Line Transceiver, read in the DDM (Digital Dia… |
| 1.3.6.1.4.1.20044.54.3.1.213 | Scalarrm10010mpMesrlineNetTxLaserTempMax | read-only | current | Max Line Trscv Tx Laser Temperature :This OID gives the maximum Tx Laser Temperature value among the network lanes of the Line Transceiver, read from the DDM (… |
| 1.3.6.1.4.1.20044.54.3.1.214 | Scalarrm10010mpMesrlineNetTxBiasCurrentMax | read-only | current | Max Line Trscv Tx Laser Bias :This OID gives the maximum Tx Laser Bias value among the network lanes of the Line Transceiver, read from the DDM (Digital Diagno… |
| 1.3.6.1.4.1.20044.54.3.1.215 | Scalarrm10010mpMesrlineNetRxInputPwrMax | read-only | current | Max Line Trscv Rx Power :This OID gives the maximum Receive power value among the network lanes of the Line Transceiver, read in the DDM (Digital Diagnostic Mo… |
| 1.3.6.1.4.1.20044.54.3.1.216 | Scalarrm10010mpMesrlineResidualChromaticDispMax | read-only | current | Max Residual Chromatic Dispersion :This OID gives the maximum Residual Chromatic Dispersion on the Line interface since the last measure reset (Unit = ps/nm)<H… |
| 1.3.6.1.4.1.20044.54.3.1.217 | Scalarrm10010mpMesrlineDiffGroupDelayMax | read-only | current | Max Differential Group Delay :This OID gives the maximum Differential Group Delay on the Line interface since the last measure reset (Unit = ps)<Help> This mea… |
| 1.3.6.1.4.1.20044.54.3.1.218 | Scalarrm10010mpMesrlineQFactorMax | read-only | current | Max Q Factor :This OID gives the maximum Q Factor on the Line interface since the last measure reset (Unit = dB)<Help> This measure gives the maximum Q Factor … |
| 1.3.6.1.4.1.20044.54.3.1.219 | Scalarrm10010mpMesrlineCarrierFreqOffsetMax | read-only | current | Max Carrier Frequency Offset :This OID gives the maximum Carrier Frequency Offset on the Line interface since the last measure reset (Unit = Mhz)<Help> This me… |
| 1.3.6.1.4.1.20044.54.3.1.220 | Scalarrm10010mpMesrlineOsnrMax | read-only | current | Max OSNR :This OID gives the maximum OSNR on the Line interface since the last measure reset (OSNR = AV/10) (Unit = dB)<Help> This measure gives the maximum OS… |
| 1.3.6.1.4.1.20044.54.3.2 | Noderm10010mpMesrClient | |||
| 1.3.6.1.4.1.20044.54.3.2.8 | Scalarrm10010mpMesrclientCfpTemp | read-only | current | Client Trscv Temperature :This OID gives the temperature value of the Client Transceiver, read from the DDM (Digital Diagnostic Monitoring) (Temperature = AV/2… |
| 1.3.6.1.4.1.20044.54.3.2.9 | Scalarrm10010mpMesrclientCfp3v3Voltage | read-only | current | Client Trscv Voltage :This OID gives the 3V3 voltage value of the Client Transceiver, read from the DDM (Digital Diagnostic Monitoring) (Voltage = AV/1000) (Un… |
| 1.3.6.1.4.1.20044.54.3.2.10 | Scalarrm10010mpMesrclientSoaBiasCurrent | read-only | current | Client Trscv SOA Bias :This OID gives the SOA bias value of the Client Transceiver, read from the DDM (Digital Diagnostic Monitoring) (Bias = AV/500) (Unit = m… |
| 1.3.6.1.4.1.20044.54.3.2.16 | Tablerm10010mpMesrclientNetTxTempTable | not-accessible | current | List of rm10010mpMesrclientNetTxTemp Article |
| 1.3.6.1.4.1.20044.54.3.2.16.1 | Rowrm10010mpMesrclientNetTxTempEntry | not-accessible | current | Row definition for the rm10010mpMesrclientNetTxTemp table |
| 1.3.6.1.4.1.20044.54.3.2.16.1.1 | Columnrm10010mpMesrclientNetTxTempIndex | read-only | current | Index definition for the rm10010mpMesrclientNetTxTemp table |
| 1.3.6.1.4.1.20044.54.3.2.16.1.2 | Columnrm10010mpMesrclientNetTxTempPortn | read-only | current | Client Trscv Temperature :This OID gives the Laser temperature value of the Client Transceiver, read from the DDM (Digital Diagnostic Monitoring) (Temperature … |
| 1.3.6.1.4.1.20044.54.3.2.32 | Tablerm10010mpMesrclientNetTxBiasTable | not-accessible | current | List of rm10010mpMesrclientNetTxBias Article |
| 1.3.6.1.4.1.20044.54.3.2.32.1 | Rowrm10010mpMesrclientNetTxBiasEntry | not-accessible | current | Row definition for the rm10010mpMesrclientNetTxBias table |
| 1.3.6.1.4.1.20044.54.3.2.32.1.1 | Columnrm10010mpMesrclientNetTxBiasIndex | read-only | current | Index definition for the rm10010mpMesrclientNetTxBias table |
| 1.3.6.1.4.1.20044.54.3.2.32.1.2 | Columnrm10010mpMesrclientNetTxBiasPortn | read-only | current | Client Trscv Laser Bias :This OID gives the Laser bias value of the Client Transceiver, read from the DDM (Digital Diagnostic Monitoring) (Bias = AV/500) (Unit… |
| 1.3.6.1.4.1.20044.54.3.2.48 | Tablerm10010mpMesrclientNetTxPwrTable | not-accessible | current | List of rm10010mpMesrclientNetTxPwr Article |
| 1.3.6.1.4.1.20044.54.3.2.48.1 | Rowrm10010mpMesrclientNetTxPwrEntry | not-accessible | current | Row definition for the rm10010mpMesrclientNetTxPwr table |
| 1.3.6.1.4.1.20044.54.3.2.48.1.1 | Columnrm10010mpMesrclientNetTxPwrIndex | read-only | current | Index definition for the rm10010mpMesrclientNetTxPwr table |
| 1.3.6.1.4.1.20044.54.3.2.48.1.2 | Columnrm10010mpMesrclientNetTxPwrPortn | read-only | current | Client Trscv Tx Power :This OID gives the transmit power value of the Client Transceiver, read from the DDM (Digital Diagnostic Monitoring) (Power = 10*log(AV)… |
| 1.3.6.1.4.1.20044.54.3.2.64 | Tablerm10010mpMesrclientNetRxPwrTable | not-accessible | current | List of rm10010mpMesrclientNetRxPwr Article |
| 1.3.6.1.4.1.20044.54.3.2.64.1 | Rowrm10010mpMesrclientNetRxPwrEntry | not-accessible | current | Row definition for the rm10010mpMesrclientNetRxPwr table |
| 1.3.6.1.4.1.20044.54.3.2.64.1.1 | Columnrm10010mpMesrclientNetRxPwrIndex | read-only | current | Index definition for the rm10010mpMesrclientNetRxPwr table |
| 1.3.6.1.4.1.20044.54.3.2.64.1.2 | Columnrm10010mpMesrclientNetRxPwrPortn | read-only | current | Client Trscv Rx Power :This OID gives the receive power value of the Client Transceiver, read in the DDM (Digital Diagnostic Monitoring) (Power = 10*log(AV)-40… |
| 1.3.6.1.4.1.20044.54.3.3 | Noderm10010mpMesrLine | |||
| 1.3.6.1.4.1.20044.54.3.3.12 | Scalarrm10010mpMesrlineMsaTemp | read-only | current | Line Trscv Temperature :This OID gives the temperature value of the Line Transceiver, read from the DDM (Digital Diagnostic Monitoring) (Temperature = AV/256) … |
| 1.3.6.1.4.1.20044.54.3.3.13 | Scalarrm10010mpMesrlineMsa3v3Voltage | read-only | current | Line Trscv Voltage :This OID gives the 3V3 voltage value of the Line Transceiver, read from the DDM (Digital Diagnostic Monitoring) (Voltage = AV/1000) (Unit =… |
| 1.3.6.1.4.1.20044.54.3.3.14 | Scalarrm10010mpMesrlineSoaBiasCurrent | read-only | current | Line Trscv SOA Bias :This OID gives the SOA bias value of the Line Transceiver,read from the DDM (Digital Diagnostic Monitoring) (Bias = AV/500) (Unit = mA) <H… |
| 1.3.6.1.4.1.20044.54.3.3.80 | Tablerm10010mpMesrlineNetTxLaserOutputPwrTable | not-accessible | current | List of rm10010mpMesrlineNetTxLaserOutputPwr Article |
| 1.3.6.1.4.1.20044.54.3.3.80.1 | Rowrm10010mpMesrlineNetTxLaserOutputPwrEntry | not-accessible | current | Row definition for the rm10010mpMesrlineNetTxLaserOutputPwr table |
| 1.3.6.1.4.1.20044.54.3.3.80.1.1 | Columnrm10010mpMesrlineNetTxLaserOutputPwrIndex | read-only | current | Index definition for the rm10010mpMesrlineNetTxLaserOutputPwr table |
| 1.3.6.1.4.1.20044.54.3.3.80.1.2 | Columnrm10010mpMesrlineNetTxLaserOutputPwrPortn | read-only | current | Current Line Trscv Tx Power :This OID gives the Tx Laser transmit power value of the Line Transceiver, read in the DDM (Digital Diagnostic Monitoring) (Power =… |
| 1.3.6.1.4.1.20044.54.3.3.96 | Tablerm10010mpMesrlineNetTxLaserTempTable | not-accessible | current | List of rm10010mpMesrlineNetTxLaserTemp Article |
| 1.3.6.1.4.1.20044.54.3.3.96.1 | Rowrm10010mpMesrlineNetTxLaserTempEntry | not-accessible | current | Row definition for the rm10010mpMesrlineNetTxLaserTemp table |
| 1.3.6.1.4.1.20044.54.3.3.96.1.1 | Columnrm10010mpMesrlineNetTxLaserTempIndex | read-only | current | Index definition for the rm10010mpMesrlineNetTxLaserTemp table |
| 1.3.6.1.4.1.20044.54.3.3.96.1.2 | Columnrm10010mpMesrlineNetTxLaserTempPortn | read-only | current | Current Line Trscv Tx Laser Temperature :This OID gives the Tx Laser Temperature value of the Line Transceiver, read from the DDM (Digital Diagnostic Monitorin… |
| 1.3.6.1.4.1.20044.54.3.3.112 | Tablerm10010mpMesrlineNetTxBiasCurrentTable | not-accessible | current | List of rm10010mpMesrlineNetTxBiasCurrent Article |
| 1.3.6.1.4.1.20044.54.3.3.112.1 | Rowrm10010mpMesrlineNetTxBiasCurrentEntry | not-accessible | current | Row definition for the rm10010mpMesrlineNetTxBiasCurrent table |
| 1.3.6.1.4.1.20044.54.3.3.112.1.1 | Columnrm10010mpMesrlineNetTxBiasCurrentIndex | read-only | current | Index definition for the rm10010mpMesrlineNetTxBiasCurrent table |
| 1.3.6.1.4.1.20044.54.3.3.112.1.2 | Columnrm10010mpMesrlineNetTxBiasCurrentPortn | read-only | current | Current Line Trscv Tx Laser Bias :This OID gives the Tx Laser Bias value of the Line Transceiver, read from the DDM (Digital Diagnostic Monitoring) (Bias = AV/… |
| 1.3.6.1.4.1.20044.54.3.3.128 | Tablerm10010mpMesrlineNetRxInputPwrTable | not-accessible | current | List of rm10010mpMesrlineNetRxInputPwr Article |
| 1.3.6.1.4.1.20044.54.3.3.128.1 | Rowrm10010mpMesrlineNetRxInputPwrEntry | not-accessible | current | Row definition for the rm10010mpMesrlineNetRxInputPwr table |
| 1.3.6.1.4.1.20044.54.3.3.128.1.1 | Columnrm10010mpMesrlineNetRxInputPwrIndex | read-only | current | Index definition for the rm10010mpMesrlineNetRxInputPwr table |
| 1.3.6.1.4.1.20044.54.3.3.128.1.2 | Columnrm10010mpMesrlineNetRxInputPwrPortn | read-only | current | Current Line Trscv Rx Power :This OID gives the Receive power value of the Line Transceiver, read in the DDM (Digital Diagnostic Monitoring) (Power = AV/100) (… |
| 1.3.6.1.4.1.20044.54.3.3.144 | Tablerm10010mpMesrlineResidualChromaticDispTable | not-accessible | current | List of rm10010mpMesrlineResidualChromaticDisp Article |
| 1.3.6.1.4.1.20044.54.3.3.144.1 | Rowrm10010mpMesrlineResidualChromaticDispEntry | not-accessible | current | Row definition for the rm10010mpMesrlineResidualChromaticDisp table |
| 1.3.6.1.4.1.20044.54.3.3.144.1.1 | Columnrm10010mpMesrlineResidualChromaticDispIndex | read-only | current | Index definition for the rm10010mpMesrlineResidualChromaticDisp table |
| 1.3.6.1.4.1.20044.54.3.3.144.1.2 | Columnrm10010mpMesrlineResidualChromaticDispPortn | read-only | current | Current Residual Chromatic Dispersion :This OID gives the current Residual Chromatic Dispersion on the Line interface (Unit = ps/nm)<Help> This measure gives t… |
| 1.3.6.1.4.1.20044.54.3.3.148 | Tablerm10010mpMesrlineDiffGroupDelayTable | not-accessible | current | List of rm10010mpMesrlineDiffGroupDelay Article |
| 1.3.6.1.4.1.20044.54.3.3.148.1 | Rowrm10010mpMesrlineDiffGroupDelayEntry | not-accessible | current | Row definition for the rm10010mpMesrlineDiffGroupDelay table |
| 1.3.6.1.4.1.20044.54.3.3.148.1.1 | Columnrm10010mpMesrlineDiffGroupDelayIndex | read-only | current | Index definition for the rm10010mpMesrlineDiffGroupDelay table |
| 1.3.6.1.4.1.20044.54.3.3.148.1.2 | Columnrm10010mpMesrlineDiffGroupDelayPortn | read-only | current | Current Differential Group Delay :This OID gives the current Differential Group Delay on the Line interface (Unit = ps)<Help> This measure gives the current Di… |
| 1.3.6.1.4.1.20044.54.3.3.152 | Tablerm10010mpMesrlineQFactorTable | not-accessible | current | List of rm10010mpMesrlineQFactor Article |
| 1.3.6.1.4.1.20044.54.3.3.152.1 | Rowrm10010mpMesrlineQFactorEntry | not-accessible | current | Row definition for the rm10010mpMesrlineQFactor table |
| 1.3.6.1.4.1.20044.54.3.3.152.1.1 | Columnrm10010mpMesrlineQFactorIndex | read-only | current | Index definition for the rm10010mpMesrlineQFactor table |
| 1.3.6.1.4.1.20044.54.3.3.152.1.2 | Columnrm10010mpMesrlineQFactorPortn | read-only | current | Current Q Factor :This OID gives the current Q Factor on the Line interface (Unit = dB) <Help> This measure gives the current Q Factor on the Line interface. |
| 1.3.6.1.4.1.20044.54.3.3.156 | Tablerm10010mpMesrlineCarrierFreqOffsetTable | not-accessible | current | List of rm10010mpMesrlineCarrierFreqOffset Article |
| 1.3.6.1.4.1.20044.54.3.3.156.1 | Rowrm10010mpMesrlineCarrierFreqOffsetEntry | not-accessible | current | Row definition for the rm10010mpMesrlineCarrierFreqOffset table |
| 1.3.6.1.4.1.20044.54.3.3.156.1.1 | Columnrm10010mpMesrlineCarrierFreqOffsetIndex | read-only | current | Index definition for the rm10010mpMesrlineCarrierFreqOffset table |
| 1.3.6.1.4.1.20044.54.3.3.156.1.2 | Columnrm10010mpMesrlineCarrierFreqOffsetPortn | read-only | current | Current Carrier Frequency Offset :This OID gives the current Carrier Frequency Offset on the Line interface (Unit = Mhz)<Help> This measure gives the current C… |
| 1.3.6.1.4.1.20044.54.3.3.160 | Tablerm10010mpMesrlineOsnrTable | not-accessible | current | List of rm10010mpMesrlineOsnr Article |
| 1.3.6.1.4.1.20044.54.3.3.160.1 | Rowrm10010mpMesrlineOsnrEntry | not-accessible | current | Row definition for the rm10010mpMesrlineOsnr table |
| 1.3.6.1.4.1.20044.54.3.3.160.1.1 | Columnrm10010mpMesrlineOsnrIndex | read-only | current | Index definition for the rm10010mpMesrlineOsnr table |
| 1.3.6.1.4.1.20044.54.3.3.160.1.2 | Columnrm10010mpMesrlineOsnrPortn | read-only | current | Current OSNR :This OID gives the current OSNR on the Line interface (OSNR = AV/10) (Unit = dB)<Help> This measure gives the current OSNR on the Line interface. |
| 1.3.6.1.4.1.20044.54.4 | Noderm10010mpcounters | |||
| 1.3.6.1.4.1.20044.54.4.1 | Noderm10010mpCntOther | |||
| 1.3.6.1.4.1.20044.54.4.2 | Noderm10010mpCntClient | |||
| 1.3.6.1.4.1.20044.54.4.2.16 | Tablerm10010mpCntclientInputErrorCounterLaneOneTable | not-accessible | current | List of rm10010mpCntclientInputErrorCounterLaneOne Article |
| 1.3.6.1.4.1.20044.54.4.2.16.1 | Rowrm10010mpCntclientInputErrorCounterLaneOneEntry | not-accessible | current | Row definition for the rm10010mpCntclientInputErrorCounterLaneOne table |
| 1.3.6.1.4.1.20044.54.4.2.16.1.1 | Columnrm10010mpCntclientInputErrorCounterLaneOneIndex | read-only | current | Index definition for the rm10010mpCntclientInputErrorCounterLaneOne table |
| 1.3.6.1.4.1.20044.54.4.2.16.1.2 | Columnrm10010mpCntclientInputErrorCounterLaneOneValuePortn | read-only | current | Client_Input_Error_Counter_Lane1 :This counter is incremented each time a coding violation is detected on the host lane of the client transceiver <Help> This c… |
| 1.3.6.1.4.1.20044.54.4.2.16.1.3 | Columnrm10010mpCntclientInputErrorCounterLaneOneErrorPortn | read-only | current | Client Input Counter Error :This OID when set indicates the rate adaptation removal counter value is invalid on Port |
| 1.3.6.1.4.1.20044.54.4.2.16.1.4 | Columnrm10010mpCntclientInputErrorCounterLaneOneOverloadPortn | read-only | current | Client Input Counter Overload :This OID when set indicates a rate adaptation removal counter overload on Port |
| 1.3.6.1.4.1.20044.54.4.2.32 | Tablerm10010mpCntclientInputErrorCounterLaneTwoTable | not-accessible | current | List of rm10010mpCntclientInputErrorCounterLaneTwo Article |
| 1.3.6.1.4.1.20044.54.4.2.32.1 | Rowrm10010mpCntclientInputErrorCounterLaneTwoEntry | not-accessible | current | Row definition for the rm10010mpCntclientInputErrorCounterLaneTwo table |
| 1.3.6.1.4.1.20044.54.4.2.32.1.1 | Columnrm10010mpCntclientInputErrorCounterLaneTwoIndex | read-only | current | Index definition for the rm10010mpCntclientInputErrorCounterLaneTwo table |
| 1.3.6.1.4.1.20044.54.4.2.32.1.2 | Columnrm10010mpCntclientInputErrorCounterLaneTwoValuePortn | read-only | current | Client_Input_Error_Counter_Lane2 :This counter is incremented each time a coding violation is detected on the host lane of the client transceiver <Help> This c… |
| 1.3.6.1.4.1.20044.54.4.2.32.1.3 | Columnrm10010mpCntclientInputErrorCounterLaneTwoErrorPortn | read-only | current | Client Input Counter Error :This OID when set indicates the client error counter value is invalid on Port |
| 1.3.6.1.4.1.20044.54.4.2.32.1.4 | Columnrm10010mpCntclientInputErrorCounterLaneTwoOverloadPortn | read-only | current | Client Input Counter Overload :This OID when set indicates a client input error counter overload on Port |
| 1.3.6.1.4.1.20044.54.4.2.80 | Tablerm10010mpCntclientInputErrorCounterTable | not-accessible | current | List of rm10010mpCntclientInputErrorCounter Article |
| 1.3.6.1.4.1.20044.54.4.2.80.1 | Rowrm10010mpCntclientInputErrorCounterEntry | not-accessible | current | Row definition for the rm10010mpCntclientInputErrorCounter table |
| 1.3.6.1.4.1.20044.54.4.2.80.1.1 | Columnrm10010mpCntclientInputErrorCounterIndex | read-only | current | Index definition for the rm10010mpCntclientInputErrorCounter table |
| 1.3.6.1.4.1.20044.54.4.2.80.1.2 | Columnrm10010mpCntclientInputErrorCounterValuePortn | read-only | current | Client Input Errors :This counter is increased each time a 10b/8b running disparity error is detected on the Client input stream <Help> This counter gives the … |
| 1.3.6.1.4.1.20044.54.4.2.80.1.3 | Columnrm10010mpCntclientInputErrorCounterErrorPortn | read-only | current | Client Counter Error :This OID when set indicates the client error counter value is invalid on Port |
| 1.3.6.1.4.1.20044.54.4.2.80.1.4 | Columnrm10010mpCntclientInputErrorCounterOverloadPortn | read-only | current | Client Counter Overload :This OID when set indicates a client input error counter overload on Port |
| 1.3.6.1.4.1.20044.54.4.2.96 | Tablerm10010mpCntclientCbipCounterTable | not-accessible | current | List of rm10010mpCntclientCbipCounter Article |
| 1.3.6.1.4.1.20044.54.4.2.96.1 | Rowrm10010mpCntclientCbipCounterEntry | not-accessible | current | Row definition for the rm10010mpCntclientCbipCounter table |
| 1.3.6.1.4.1.20044.54.4.2.96.1.1 | Columnrm10010mpCntclientCbipCounterIndex | read-only | current | Index definition for the rm10010mpCntclientCbipCounter table |
| 1.3.6.1.4.1.20044.54.4.2.96.1.2 | Columnrm10010mpCntclientCbipCounterValuePortn | read-only | current | Client Output Errors :This counter is incremented each time a CBIP parity error is detected on the Client output stream <Help> This counter gives the number of… |
| 1.3.6.1.4.1.20044.54.4.2.96.1.3 | Columnrm10010mpCntclientCbipCounterErrorPortn | read-only | current | Client Counter Error :This OID when set indicates the CBIP error counter value is invalid on Port |
| 1.3.6.1.4.1.20044.54.4.2.96.1.4 | Columnrm10010mpCntclientCbipCounterOverloadPortn | read-only | current | Client CBIP Counter Overload :This OID when set indicates a CBIP error counter overload on Port |
| 1.3.6.1.4.1.20044.54.4.3 | Noderm10010mpCntLine | |||
| 1.3.6.1.4.1.20044.54.4.3.192 | Tablerm10010mpCntlocalLineSmBip8ErrorCounterTable | not-accessible | current | List of rm10010mpCntlocalLineSmBip8ErrorCounter Article |
| 1.3.6.1.4.1.20044.54.4.3.192.1 | Rowrm10010mpCntlocalLineSmBip8ErrorCounterEntry | not-accessible | current | Row definition for the rm10010mpCntlocalLineSmBip8ErrorCounter table |
| 1.3.6.1.4.1.20044.54.4.3.192.1.1 | Columnrm10010mpCntlocalLineSmBip8ErrorCounterIndex | read-only | current | Index definition for the rm10010mpCntlocalLineSmBip8ErrorCounter table |
| 1.3.6.1.4.1.20044.54.4.3.192.1.2 | Columnrm10010mpCntlocalLineSmBip8ErrorCounterValuePortn | read-only | current | Line Input SM-BIP8 Errors :This OID gives the current Bit Error Rate (residual SM-BIP8 error) after FEC <Help> This counter gives the current Bit Error Rate (r… |
| 1.3.6.1.4.1.20044.54.4.3.192.1.3 | Columnrm10010mpCntlocalLineSmBip8ErrorCounterErrorPortn | read-only | current | Line Counter Error :This OID when set indicates the B1 error counter value is invalid on Port |
| 1.3.6.1.4.1.20044.54.4.3.192.1.4 | Columnrm10010mpCntlocalLineSmBip8ErrorCounterOverloadPortn | read-only | current | Line Counter Overload :This OID when set indicates a B1 error counter overload on Port |
| 1.3.6.1.4.1.20044.54.4.3.193 | Tablerm10010mpCntlocalLineFecCorrectedErrorsCounterTable | not-accessible | current | List of rm10010mpCntlocalLineFecCorrectedErrorsCounter Article |
| 1.3.6.1.4.1.20044.54.4.3.193.1 | Rowrm10010mpCntlocalLineFecCorrectedErrorsCounterEntry | not-accessible | current | Row definition for the rm10010mpCntlocalLineFecCorrectedErrorsCounter table |
| 1.3.6.1.4.1.20044.54.4.3.193.1.1 | Columnrm10010mpCntlocalLineFecCorrectedErrorsCounterIndex | read-only | current | Index definition for the rm10010mpCntlocalLineFecCorrectedErrorsCounter table |
| 1.3.6.1.4.1.20044.54.4.3.193.1.2 | Columnrm10010mpCntlocalLineFecCorrectedErrorsCounterValuePortn | read-only | current | Line Input HD FEC Corrected Errors :This OID gives the current Bit Error Rate before the Hard Decision FEC <Help> This counter gives the current Bit Error Rate… |
| 1.3.6.1.4.1.20044.54.4.3.193.1.3 | Columnrm10010mpCntlocalLineFecCorrectedErrorsCounterErrorPortn | read-only | current | FEC Counter Error :This bit when set indicates the FEC corrected errors counter value is invalid on Line |
| 1.3.6.1.4.1.20044.54.4.3.193.1.4 | Columnrm10010mpCntlocalLineFecCorrectedErrorsCounterOverloadPortn | read-only | current | FEC Counter Overload :This bit when set indicates a FEC corrected errors counter overload on Line |
| 1.3.6.1.4.1.20044.54.4.3.194 | Tablerm10010mpCntremoteLineSmBip8ErrorCounterTable | not-accessible | current | List of rm10010mpCntremoteLineSmBip8ErrorCounter Article |
| 1.3.6.1.4.1.20044.54.4.3.194.1 | Rowrm10010mpCntremoteLineSmBip8ErrorCounterEntry | not-accessible | current | Row definition for the rm10010mpCntremoteLineSmBip8ErrorCounter table |
| 1.3.6.1.4.1.20044.54.4.3.194.1.1 | Columnrm10010mpCntremoteLineSmBip8ErrorCounterIndex | read-only | current | Index definition for the rm10010mpCntremoteLineSmBip8ErrorCounter table |
| 1.3.6.1.4.1.20044.54.4.3.194.1.2 | Columnrm10010mpCntremoteLineSmBip8ErrorCounterValuePortn | read-only | current | Remote SM BIP8 :This OID gives the current Bit Error Rate (residual SM-BIP8 error) after FEC on the remote side <Help> This counter gives the current Bit Error… |
| 1.3.6.1.4.1.20044.54.4.3.194.1.3 | Columnrm10010mpCntremoteLineSmBip8ErrorCounterErrorPortn | read-only | current | Remote Counter Error : |
| 1.3.6.1.4.1.20044.54.4.3.194.1.4 | Columnrm10010mpCntremoteLineSmBip8ErrorCounterOverloadPortn | read-only | current | Remote Counter Overload : |
| 1.3.6.1.4.1.20044.54.4.3.195 | Tablerm10010mpCntlineDfrmTimCntTable | not-accessible | current | List of rm10010mpCntlineDfrmTimCnt Article |
| 1.3.6.1.4.1.20044.54.4.3.195.1 | Rowrm10010mpCntlineDfrmTimCntEntry | not-accessible | current | Row definition for the rm10010mpCntlineDfrmTimCnt table |
| 1.3.6.1.4.1.20044.54.4.3.195.1.1 | Columnrm10010mpCntlineDfrmTimCntIndex | read-only | current | Index definition for the rm10010mpCntlineDfrmTimCnt table |
| 1.3.6.1.4.1.20044.54.4.3.195.1.2 | Columnrm10010mpCntlineDfrmTimCntValuePortn | read-only | current | Line Timer Counter : |
| 1.3.6.1.4.1.20044.54.4.3.195.1.3 | Columnrm10010mpCntlineDfrmTimCntErrorPortn | read-only | current | Line Counter Error :This OID when set indicates the deframer timer counter value is invalid on Port |
| 1.3.6.1.4.1.20044.54.4.3.195.1.4 | Columnrm10010mpCntlineDfrmTimCntOverloadPortn | read-only | current | Line Counter Overload :This OID when set indicates a deframer timer counter overload on Port |
| 1.3.6.1.4.1.20044.54.4.3.196 | Tablerm10010mpCntlocalLineTrscvFecCorrectedErrorCounterTable | not-accessible | current | List of rm10010mpCntlocalLineTrscvFecCorrectedErrorCounter Article |
| 1.3.6.1.4.1.20044.54.4.3.196.1 | Rowrm10010mpCntlocalLineTrscvFecCorrectedErrorCounterEntry | not-accessible | current | Row definition for the rm10010mpCntlocalLineTrscvFecCorrectedErrorCounter table |
| 1.3.6.1.4.1.20044.54.4.3.196.1.1 | Columnrm10010mpCntlocalLineTrscvFecCorrectedErrorCounterIndex | read-only | current | Index definition for the rm10010mpCntlocalLineTrscvFecCorrectedErrorCounter table |
| 1.3.6.1.4.1.20044.54.4.3.196.1.2 | Columnrm10010mpCntlocalLineTrscvFecCorrectedErrorCounterValuePortn | read-only | current | Line Input SD FEC Corrected Errors :This OID gives the current Bit Error Rate before the Soft Decision FEC <Help> This counter gives the current Bit Error Rate… |
| 1.3.6.1.4.1.20044.54.4.3.196.1.3 | Columnrm10010mpCntlocalLineTrscvFecCorrectedErrorCounterErrorPortn | read-only | current | Line Counter Error :This OID when set indicates the deframer timer counter value is invalid on Port |
| 1.3.6.1.4.1.20044.54.4.3.196.1.4 | Columnrm10010mpCntlocalLineTrscvFecCorrectedErrorCounterOverloadPortn | read-only | current | Line Counter Overload :This OID when set indicates a deframer timer counter overload on Port |
| 1.3.6.1.4.1.20044.54.4.3.197 | Tablerm10010mpCntlocalLineTrscvFecUncorrectedErrorCounterTable | not-accessible | current | List of rm10010mpCntlocalLineTrscvFecUncorrectedErrorCounter Article |
| 1.3.6.1.4.1.20044.54.4.3.197.1 | Rowrm10010mpCntlocalLineTrscvFecUncorrectedErrorCounterEntry | not-accessible | current | Row definition for the rm10010mpCntlocalLineTrscvFecUncorrectedErrorCounter table |
| 1.3.6.1.4.1.20044.54.4.3.197.1.1 | Columnrm10010mpCntlocalLineTrscvFecUncorrectedErrorCounterIndex | read-only | current | Index definition for the rm10010mpCntlocalLineTrscvFecUncorrectedErrorCounter table |
| 1.3.6.1.4.1.20044.54.4.3.197.1.2 | Columnrm10010mpCntlocalLineTrscvFecUncorrectedErrorCounterValuePortn | read-only | current | SD Uncorrected :This OID gives the current Bit Error Rate after the Soft Decision FEC (residual) <Help> This counter gives the current Bit Error Rate after the… |
| 1.3.6.1.4.1.20044.54.4.3.197.1.3 | Columnrm10010mpCntlocalLineTrscvFecUncorrectedErrorCounterErrorPortn | read-only | current | Line Counter Error :This OID when set indicates the deframer timer counter value is invalid on Port |
| 1.3.6.1.4.1.20044.54.4.3.197.1.4 | Columnrm10010mpCntlocalLineTrscvFecUncorrectedErrorCounterOverloadPortn | read-only | current | Line Counter Overload :This OID when set indicates a deframer timer counter overload on Port |
| 1.3.6.1.4.1.20044.54.6 | Noderm10010mpcontrolsWrite | |||
| 1.3.6.1.4.1.20044.54.6.1 | Noderm10010mpCtrlOther | |||
| 1.3.6.1.4.1.20044.54.6.1.1 | Noderm10010mpCtrlconfMgnt1 | |||
| 1.3.6.1.4.1.20044.54.6.1.1.1 | Scalarrm10010mpCtrlConf1Load1 | read-write | current | Load Configuration Tables Set Nb 1 :When set this OID enables loading from flash configuration1 into the PM. |
| 1.3.6.1.4.1.20044.54.6.1.1.2 | Scalarrm10010mpCtrlConf2Load1 | read-write | current | Load Configuration Tables Set Nb 2 :When set this OID enables loading from flash configuration2 into the PM. |
| 1.3.6.1.4.1.20044.54.6.1.1.10 | Scalarrm10010mpCtrlConf2Flash1 | read-write | current | Write Configuration Tables :This OID saves the current configuration of the PM as configuration2 in the flash. <Help> This control saves the customer configura… |
| 1.3.6.1.4.1.20044.54.6.1.1.14 | Scalarrm10010mpCtrlConf2Clear1 | read-write | current | Clear Configuration Tables :This OID clears the configuration tables from configuration2 in the flash. <Help> This control restores the default configuration o… |
| 1.3.6.1.4.1.20044.54.6.1.4 | Noderm10010mpCtrlsynth4 | |||
| 1.3.6.1.4.1.20044.54.6.1.4.1 | Scalarrm10010mpCtrlCorrelatOn | read-write | current | Enable Alarm Correlation :This OID enables the alarm correlation in the PM. |
| 1.3.6.1.4.1.20044.54.6.1.4.2 | Scalarrm10010mpCtrlCorrelatOff | read-write | current | Disable Alarm Correlation :This OID disables the alarm correlation in the PM. |
| 1.3.6.1.4.1.20044.54.6.1.5 | Noderm10010mpCtrlswMgnt | |||
| 1.3.6.1.4.1.20044.54.6.1.5.2 | Scalarrm10010mpCtrlColdReset | read-write | current | PM Cold Reset :This OID, when set, causes a cold reset of the PM. This reset is traffic affecting, and the configuration of PM is reloaded on start-up. <Help> … |
| 1.3.6.1.4.1.20044.54.6.1.5.3 | Scalarrm10010mpCtrlWarmReset | read-write | current | PM Warm Reset :This OID, when set, causes a warm reset of the PM. This reset is not traffic affecting, and the configuration of PM remains unchanged. <Help> Th… |
| 1.3.6.1.4.1.20044.54.6.1.5.5 | Scalarrm10010mpCtrlLoadSwBank1 | read-write | current | Set Software Nb 1 As Active :This OID, when set, loads the SW from bank1 into the PM. It must be followed by a reset. <Help> This controls selects the first SW… |
| 1.3.6.1.4.1.20044.54.6.1.5.6 | Scalarrm10010mpCtrlLoadSwBank2 | read-write | current | Set Software Nb 2 As Active :This OID, when set, loads the SW from bank2 into the PM. It must be followed by a reset. <Help> This controls selects the second S… |
| 1.3.6.1.4.1.20044.54.6.1.6 | Noderm10010mpCtrlgwMgnt | |||
| 1.3.6.1.4.1.20044.54.6.1.6.1 | Scalarrm10010mpCtrlCurrentGwReset | read-write | current | Active Gateware Reset :This OID, when set, resets the active gateware. It is traffic affecting. |
| 1.3.6.1.4.1.20044.54.6.1.6.5 | Scalarrm10010mpCtrlLoadGwBank1 | read-write | current | Set Gateware Nb 1 As Active :This OID, when set, loads the GW from bank1 (Flash) into the PM. It is followed by an automatic gateware cold reset. <Help> This c… |
| 1.3.6.1.4.1.20044.54.6.1.6.6 | Scalarrm10010mpCtrlLoadGwBank2 | read-write | current | Set Gateware Nb 2 As Active :This OID, when set, loads the GW from bank2 (Flash) into the PM. It is followed by an automatic gateware cold reset. |
| 1.3.6.1.4.1.20044.54.6.1.6.7 | Scalarrm10010mpCtrlLoadGwBank3 | read-write | current | Set Gateware Nb 3 As Active :This OID, when set, loads the GW from bank3 (Flash) into the PM. It is followed by an automatic gateware cold reset. <Help> This c… |
| 1.3.6.1.4.1.20044.54.6.1.6.8 | Scalarrm10010mpCtrlLoadGwBank4 | read-write | current | Set Gateware Nb 4 As Active :This OID, when set, loads the GW from bank4 (Flash) into the PM. It is followed by an automatic gateware cold reset. |
| 1.3.6.1.4.1.20044.54.6.1.192 | Noderm10010mpCtrlledTest | |||
| 1.3.6.1.4.1.20044.54.6.1.192.1 | Scalarrm10010mpCtrlGreenLed | read-write | current | Green Leds Test :This OID switches on all the green Leds as a test feature. <Help> This control initiates a test leds turning all the LEDs to green |
| 1.3.6.1.4.1.20044.54.6.1.192.2 | Scalarrm10010mpCtrlRedLed | read-write | current | Red Leds Test :This OID switches on all the red Leds as a test feature. <Help> This control initiates a test leds turning all the LEDs to red |
| 1.3.6.1.4.1.20044.54.6.1.192.3 | Scalarrm10010mpCtrlLedOff | read-write | current | Leds Off :This OID switches off all the Leds as a test feature. <Help> This control initiates a test leds turning all the LEDs to OFF |
| 1.3.6.1.4.1.20044.54.6.1.201 | Noderm10010mpCtrlinitSwitchMarvell | |||
| 1.3.6.1.4.1.20044.54.6.1.201.1 | Scalarrm10010mpCtrlInitSwitchMarvell | read-write | current | Switch Initialization :This OID operates an initialization of the switch managed through the module <Help> This control activates an initialization of the swit… |
| 1.3.6.1.4.1.20044.54.6.1.259 | Noderm10010mpCtrlresetCount | |||
| 1.3.6.1.4.1.20044.54.6.1.259.1 | Scalarrm10010mpCtrlResetcount | read-write | current | Module Count Global Reset :This OID resets all the errors counters on the module <Help > This control initiates a reset of the errors counters on the module |
| 1.3.6.1.4.1.20044.54.6.1.260 | Noderm10010mpCtrlresetRmon | |||
| 1.3.6.1.4.1.20044.54.6.1.260.1 | Scalarrm10010mpCtrlResetrmon | read-write | current | Module Rmon Global Reset :This OID resets all the Rmon counters on the module <Help > This control initiates a reset of the Rmon counters on the module |
| 1.3.6.1.4.1.20044.54.6.1.261 | Noderm10010mpCtrlresetMeasurements | |||
| 1.3.6.1.4.1.20044.54.6.1.261.1 | Scalarrm10010mpCtrlResetmeasurements | read-write | current | Management Meas Global Reset :This OID resets some measurements on the management <Help > This control initiates a reset of some measurements on the management |
| 1.3.6.1.4.1.20044.54.6.2 | Noderm10010mpCtrlClient | |||
| 1.3.6.1.4.1.20044.54.6.2.16 | Tablerm10010mpCtrlaccessLoopTable | not-accessible | current | List of rm10010mpCtrlaccessLoop Article |
| 1.3.6.1.4.1.20044.54.6.2.16.1 | Rowrm10010mpCtrlaccessLoopEntry | not-accessible | current | Row definition for the rm10010mpCtrlaccessLoop table |
| 1.3.6.1.4.1.20044.54.6.2.16.1.1 | Columnrm10010mpCtrlaccessLoopIndex | read-only | current | Index definition for the rm10010mpCtrlaccessLoop table |
| 1.3.6.1.4.1.20044.54.6.2.16.1.2 | Columnrm10010mpCtrlaccessLoopPortn | read-write | current | Client Facility Loopback :This OID, when set at '1' puts the client port in loopback, looping the received 10 Gb/s signal on the transmit 10 Gb/s output. <Help… |
| 1.3.6.1.4.1.20044.54.6.2.17 | Tablerm10010mpCtrlclientLoopToLineTable | not-accessible | current | List of rm10010mpCtrlclientLoopToLine Article |
| 1.3.6.1.4.1.20044.54.6.2.17.1 | Rowrm10010mpCtrlclientLoopToLineEntry | not-accessible | current | Row definition for the rm10010mpCtrlclientLoopToLine table |
| 1.3.6.1.4.1.20044.54.6.2.17.1.1 | Columnrm10010mpCtrlclientLoopToLineIndex | read-only | current | Index definition for the rm10010mpCtrlclientLoopToLine table |
| 1.3.6.1.4.1.20044.54.6.2.17.1.2 | Columnrm10010mpCtrlclientLoopToLinePortn | read-write | current | Client Terminal Loopback :This OID, when set, puts the client port in loop back, looping the 10 Gb/s output signal on the 10 Gb/s input.<Help> This control ena… |
| 1.3.6.1.4.1.20044.54.6.2.21 | Tablerm10010mpCtrlcsfUpInsTable | not-accessible | current | List of rm10010mpCtrlcsfUpIns Article |
| 1.3.6.1.4.1.20044.54.6.2.21.1 | Rowrm10010mpCtrlcsfUpInsEntry | not-accessible | current | Row definition for the rm10010mpCtrlcsfUpIns table |
| 1.3.6.1.4.1.20044.54.6.2.21.1.1 | Columnrm10010mpCtrlcsfUpInsIndex | read-only | current | Index definition for the rm10010mpCtrlcsfUpIns table |
| 1.3.6.1.4.1.20044.54.6.2.21.1.2 | Columnrm10010mpCtrlcsfUpInsPortn | read-write | current | Client Signal Fail Insertion :This OID, when set, inserts a client signal fail in the upstream client Port. <Help> This control inserts a Client Signal Fail fo… |
| 1.3.6.1.4.1.20044.54.6.2.22 | Tablerm10010mpCtrlcaisDwInsTable | not-accessible | current | List of rm10010mpCtrlcaisDwIns Article |
| 1.3.6.1.4.1.20044.54.6.2.22.1 | Rowrm10010mpCtrlcaisDwInsEntry | not-accessible | current | Row definition for the rm10010mpCtrlcaisDwIns table |
| 1.3.6.1.4.1.20044.54.6.2.22.1.1 | Columnrm10010mpCtrlcaisDwInsIndex | read-only | current | Index definition for the rm10010mpCtrlcaisDwIns table |
| 1.3.6.1.4.1.20044.54.6.2.22.1.2 | Columnrm10010mpCtrlcaisDwInsPortn | read-write | current | Client AIS Insertion :This OID, when set, inserts a client AIS on the downstream client Port. <Help> This control inserts a Client AIS for the client port |
| 1.3.6.1.4.1.20044.54.6.3 | Noderm10010mpCtrlLine | |||
| 1.3.6.1.4.1.20044.54.6.3.64 | Tablerm10010mpCtrlcommAccessLoopTable | not-accessible | current | List of rm10010mpCtrlcommAccessLoop Article |
| 1.3.6.1.4.1.20044.54.6.3.64.1 | Rowrm10010mpCtrlcommAccessLoopEntry | not-accessible | current | Row definition for the rm10010mpCtrlcommAccessLoop table |
| 1.3.6.1.4.1.20044.54.6.3.64.1.1 | Columnrm10010mpCtrlcommAccessLoopIndex | read-only | current | Index definition for the rm10010mpCtrlcommAccessLoop table |
| 1.3.6.1.4.1.20044.54.6.3.64.1.2 | Columnrm10010mpCtrlcommAccessLoopPortn | read-write | current | Line Terminal Loopback :This OID, when set, puts the module in common access loop back, looping the 100 Gb/s output signal on the 100 Gb/s input.<Help> This co… |
| 1.3.6.1.4.1.20044.54.6.3.66 | Tablerm10010mpCtrllineLoopTable | not-accessible | current | List of rm10010mpCtrllineLoop Article |
| 1.3.6.1.4.1.20044.54.6.3.66.1 | Rowrm10010mpCtrllineLoopEntry | not-accessible | current | Row definition for the rm10010mpCtrllineLoop table |
| 1.3.6.1.4.1.20044.54.6.3.66.1.1 | Columnrm10010mpCtrllineLoopIndex | read-only | current | Index definition for the rm10010mpCtrllineLoop table |
| 1.3.6.1.4.1.20044.54.6.3.66.1.2 | Columnrm10010mpCtrllineLoopPortn | read-write | current | Line Facility Loopback :This OID, when set at '1' puts the module in line loopback mode, looping the received 100 Gb/s signal on the transmit 100 Gb/s output. … |
| 1.3.6.1.4.1.20044.54.6.3.69 | Tablerm10010mpCtrlfecDisableTable | not-accessible | current | List of rm10010mpCtrlfecDisable Article |
| 1.3.6.1.4.1.20044.54.6.3.69.1 | Rowrm10010mpCtrlfecDisableEntry | not-accessible | current | Row definition for the rm10010mpCtrlfecDisable table |
| 1.3.6.1.4.1.20044.54.6.3.69.1.1 | Columnrm10010mpCtrlfecDisableIndex | read-only | current | Index definition for the rm10010mpCtrlfecDisable table |
| 1.3.6.1.4.1.20044.54.6.3.69.1.2 | Columnrm10010mpCtrlfecDisablePortn | read-write | current | Forward Error Correction Inhibition :This OID, when set, inhibits the Forward Error Correction feature on the line input <Help> This control enables/disables t… |
| 1.3.6.1.4.1.20044.54.6.3.209 | Tablerm10010mpCtrlmsaLineLoopTable | not-accessible | current | List of rm10010mpCtrlmsaLineLoop Article |
| 1.3.6.1.4.1.20044.54.6.3.209.1 | Rowrm10010mpCtrlmsaLineLoopEntry | not-accessible | current | Row definition for the rm10010mpCtrlmsaLineLoop table |
| 1.3.6.1.4.1.20044.54.6.3.209.1.1 | Columnrm10010mpCtrlmsaLineLoopIndex | read-only | current | Index definition for the rm10010mpCtrlmsaLineLoop table |
| 1.3.6.1.4.1.20044.54.6.3.209.1.2 | Columnrm10010mpCtrlmsaLineLoopPortn | read-write | current | MSA Line Loop :This OID operates a line loopback on the MSA Line <Help> This control defines the line loop back of the line transceiver |
| 1.3.6.1.4.1.20044.54.6.3.210 | Tablerm10010mpCtrlmsaTxResetTable | not-accessible | current | List of rm10010mpCtrlmsaTxReset Article |
| 1.3.6.1.4.1.20044.54.6.3.210.1 | Rowrm10010mpCtrlmsaTxResetEntry | not-accessible | current | Row definition for the rm10010mpCtrlmsaTxReset table |
| 1.3.6.1.4.1.20044.54.6.3.210.1.1 | Columnrm10010mpCtrlmsaTxResetIndex | read-only | current | Index definition for the rm10010mpCtrlmsaTxReset table |
| 1.3.6.1.4.1.20044.54.6.3.210.1.2 | Columnrm10010mpCtrlmsaTxResetPortn | read-write | current | Line MSA TX Reset :This OID resets the TX portion of the MSA line module <Help > This control initiates a reset of the transmitting side |
| 1.3.6.1.4.1.20044.54.6.3.211 | Tablerm10010mpCtrlmsaRxResetTable | not-accessible | current | List of rm10010mpCtrlmsaRxReset Article |
| 1.3.6.1.4.1.20044.54.6.3.211.1 | Rowrm10010mpCtrlmsaRxResetEntry | not-accessible | current | Row definition for the rm10010mpCtrlmsaRxReset table |
| 1.3.6.1.4.1.20044.54.6.3.211.1.1 | Columnrm10010mpCtrlmsaRxResetIndex | read-only | current | Index definition for the rm10010mpCtrlmsaRxReset table |
| 1.3.6.1.4.1.20044.54.6.3.211.1.2 | Columnrm10010mpCtrlmsaRxResetPortn | read-write | current | Line MSA RX Reset :This OID resets the RX portion of the MSA line module <Help > This control initiates a reset of the receiving side |
| 1.3.6.1.4.1.20044.54.6.3.212 | Tablerm10010mpCtrlmsaShutdownTable | not-accessible | current | List of rm10010mpCtrlmsaShutdown Article |
| 1.3.6.1.4.1.20044.54.6.3.212.1 | Rowrm10010mpCtrlmsaShutdownEntry | not-accessible | current | Row definition for the rm10010mpCtrlmsaShutdown table |
| 1.3.6.1.4.1.20044.54.6.3.212.1.1 | Columnrm10010mpCtrlmsaShutdownIndex | read-only | current | Index definition for the rm10010mpCtrlmsaShutdown table |
| 1.3.6.1.4.1.20044.54.6.3.212.1.2 | Columnrm10010mpCtrlmsaShutdownPortn | read-write | current | Line MSA Shutdown :This OID enters a process to shutdown the MSA line module <Help > This control initiates a shutdown of the module |
| 1.3.6.1.4.1.20044.54.7 | Noderm10010mpri | |||
| 1.3.6.1.4.1.20044.54.7.1 | Noderm10010mpriTable | |||
| 1.3.6.1.4.1.20044.54.7.1.1 | Tablerm10010mpRinvSfpTable | not-accessible | current | List of the SFPs on the selected module |
| 1.3.6.1.4.1.20044.54.7.1.1.1 | Rowrm10010mpRinvSfpEntry | not-accessible | current | Row definition for the SFP table |
| 1.3.6.1.4.1.20044.54.7.1.1.1.1 | Columnrm10010mpRinvSfpIndex | read-only | current | Index for SFP table |
| 1.3.6.1.4.1.20044.54.7.1.1.1.2 | Columnrm10010mpRinvsfp | read-only | current | Inventory for the SFP: This OID contains the inventory for the SFP |
| 1.3.6.1.4.1.20044.54.7.1.2 | Tablerm10010mpRinvLineTable | not-accessible | current | List of the XFPs on the selected module |
| 1.3.6.1.4.1.20044.54.7.1.2.1 | Rowrm10010mpRinvLineEntry | not-accessible | current | Row definition for the XFP table |
| 1.3.6.1.4.1.20044.54.7.1.2.1.1 | Columnrm10010mpRinvLineIndex | read-only | current | Index for XFP table |
| 1.3.6.1.4.1.20044.54.7.1.2.1.2 | Columnrm10010mpRinvxfpLine | read-only | current | Inventory for the XFP: This OID contains the inventory for the XFP |
| 1.3.6.1.4.1.20044.54.7.2 | Scalarrm10010mpRinvReloadInventory | read-write | current | Reload the inventory: This OID triggers an inventory reload. |
| 1.3.6.1.4.1.20044.54.7.3 | Scalarrm10010mpRinvHwPlatform | read-only | current | HW platform description: This OID contains the description of the Hardware platform. |
| 1.3.6.1.4.1.20044.54.7.4 | Scalarrm10010mpRinvModulePlatform | read-only | current | Module platform description: This OID contains the description of the Module. |
| 1.3.6.1.4.1.20044.54.7.5 | Scalarrm10010mpRinvSwPlatform | read-only | current | SW platform description: This OID contains the description of the Software platform. |
| 1.3.6.1.4.1.20044.54.7.6 | Scalarrm10010mpRinvGwPlatform | read-only | current | GW platform desciption: This OID contains the description of the Gateware platform. |
| 1.3.6.1.4.1.20044.54.8 | Noderm10010mpdownload | |||
| 1.3.6.1.4.1.20044.54.8.1 | Noderm10010mpDwlOther | |||
| 1.3.6.1.4.1.20044.54.8.1.0 | Noderm10010mpDwlrestartProcess | |||
| 1.3.6.1.4.1.20044.54.8.1.0.1 | Scalarrm10010mpDwlWarmRestartProcessed | read-only | current | Warm Restart :This OID indicates that the module last restart was a Warm RESTART |
| 1.3.6.1.4.1.20044.54.8.1.0.2 | Scalarrm10010mpDwlColdRestartProcessed | read-only | current | Cold Restart :This OID indicates that the module last restart was a Cold RESTART |
| 1.3.6.1.4.1.20044.54.8.1.1 | Noderm10010mpDwlswBanksUsed | |||
| 1.3.6.1.4.1.20044.54.8.1.1.1 | Scalarrm10010mpDwlSwBank1Used | read-only | current | SW bank 1 active :This OID indicates the module is working on SW bank 1 <Help> This status indicates if the SW bank 1 is active or standby |
| 1.3.6.1.4.1.20044.54.8.1.1.2 | Scalarrm10010mpDwlSwBank2Used | read-only | current | SW bank 2 active :This OID indicates the module is working on SW bank 2 <Help> This status indicates if the SW bank 2 is active or standby |
| 1.3.6.1.4.1.20044.54.8.1.1.5 | Scalarrm10010mpDwlSwBank1Notempty | read-only | current | SW bank 1 loaded :This OID indicates a software is loaded in SW bank 1 <Help> This status indicates if the SW bank 1 contains SW package |
| 1.3.6.1.4.1.20044.54.8.1.1.6 | Scalarrm10010mpDwlSwBank2Notempty | read-only | current | SW bank 2 loaded :This OID indicates a software is loaded in SW bank 2 <Help> This status indicates if the SW bank 2 contains SW package |
| 1.3.6.1.4.1.20044.54.8.1.2 | Noderm10010mpDwlgwBanksUsed | |||
| 1.3.6.1.4.1.20044.54.8.1.2.1 | Scalarrm10010mpDwlGwBank1Used | read-only | current | GW bank 1 active :This OID indicates the module is working on GW bank 1 <Help> This status indicates if the GW bank 1 is active or standby |
| 1.3.6.1.4.1.20044.54.8.1.2.2 | Scalarrm10010mpDwlGwBank2Used | read-only | current | GW bank 2 active :This OID indicates the module is working on GW bank 2 |
| 1.3.6.1.4.1.20044.54.8.1.2.3 | Scalarrm10010mpDwlGwBank3Used | read-only | current | GW bank 3 active :This OID indicates the module is working on GW bank 3 <Help> This status indicates if the GW bank 3 is active or standby |
| 1.3.6.1.4.1.20044.54.8.1.2.4 | Scalarrm10010mpDwlGwBank4Used | read-only | current | GW bank 4 active :This OID indicates the module is working on GW bank 4 |
| 1.3.6.1.4.1.20044.54.8.1.2.5 | Scalarrm10010mpDwlGwBank1Notempty | read-only | current | GW bank 1 loaded :This OID indicates a gateware is loaded in GW bank 1 <Help> This status indicates if the GW bank 1 contains GW package |
| 1.3.6.1.4.1.20044.54.8.1.2.6 | Scalarrm10010mpDwlGwBank2Notempty | read-only | current | GW bank 2 loaded :This OID indicates a gateware is loaded in GW bank 2 |
| 1.3.6.1.4.1.20044.54.8.1.2.7 | Scalarrm10010mpDwlGwBank3Notempty | read-only | current | GW bank 3 loaded :This OID indicates a gateware is loaded in GW bank 3 <Help> This status indicates if the GW bank 3 contains GW package |
| 1.3.6.1.4.1.20044.54.8.1.2.8 | Scalarrm10010mpDwlGwBank4Notempty | read-only | current | GW bank 4 loaded :This OID indicates a gateware is loaded in GW bank 4 |
| 1.3.6.1.4.1.20044.54.8.2 | Noderm10010mpDwlClient | |||
| 1.3.6.1.4.1.20044.54.8.3 | Noderm10010mpDwlLine | |||
| 1.3.6.1.4.1.20044.54.9 | Noderm10010mpConfig | |||
| 1.3.6.1.4.1.20044.54.9.1 | Noderm10010mpCfgAccessCAisCsf | |||
| 1.3.6.1.4.1.20044.54.9.1.1 | Tablerm10010mpCfgClientcaiscsfTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.54.9.1.1.1 | Rowrm10010mpCfgClientcaiscsfEntry | not-accessible | current | Row definition for the accessCAisCsf table |
| 1.3.6.1.4.1.20044.54.9.1.1.1.1 | Columnrm10010mpCfgClientcaiscsfIndex | read-only | current | Index definition for the clientcaiscsf table |
| 1.3.6.1.4.1.20044.54.9.1.1.1.3 | Columnrm10010mpCfgReservePortn | read-write | current | CAIS mode on Client Port :This register enables/disables port laser shutdown on CAIS insertion condition |
| 1.3.6.1.4.1.20044.54.9.2 | Noderm10010mpCfgStartup | |||
| 1.3.6.1.4.1.20044.54.9.2.1 | Tablerm10010mpCfgClientStartupTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.54.9.2.1.1 | Rowrm10010mpCfgClientStartupEntry | not-accessible | current | Row definition for the startup table |
| 1.3.6.1.4.1.20044.54.9.2.1.1.1 | Columnrm10010mpCfgClientStartupIndex | read-only | current | Index definition for the clientStartup table |
| 1.3.6.1.4.1.20044.54.9.2.1.1.3 | Columnrm10010mpCfgSystConfPortPortn | read-write | current | Default Settings on Client Port :This register configures the default initialisation settings on the port. |
| 1.3.6.1.4.1.20044.54.9.2.1.1.4 | Columnrm10010mpCfgNetConfPortPortn | read-write | current | Default Settings on Client Port :This register configures the default initialisation settings on the port. |
| 1.3.6.1.4.1.20044.54.9.2.1.1.14 | Columnrm10010mpCfgOptionsPortPortn | read-write | current | Default Options on Client Port :This register configures the default options on the port. |
| 1.3.6.1.4.1.20044.54.9.2.2 | Tablerm10010mpCfgLineStartupTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.54.9.2.2.1 | Rowrm10010mpCfgLineStartupEntry | not-accessible | current | Row definition for the startup table |
| 1.3.6.1.4.1.20044.54.9.2.2.1.1 | Columnrm10010mpCfgLineStartupIndex | read-only | current | Index definition for the lineStartup table |
| 1.3.6.1.4.1.20044.54.9.2.2.1.3 | Columnrm10010mpCfgSystConfLinePortn | read-write | current | Default Settings on Line :This register configures the default initialisation settings on Line |
| 1.3.6.1.4.1.20044.54.9.2.2.1.14 | Columnrm10010mpCfgOptionsLinePortn | read-write | current | Default Options on Line :This register configures the default options on the line |
| 1.3.6.1.4.1.20044.54.9.2.3 | Tablerm10010mpCfgXfpTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.54.9.2.3.1 | Rowrm10010mpCfgXfpEntry | not-accessible | current | Row definition for the startup table |
| 1.3.6.1.4.1.20044.54.9.2.3.1.1 | Columnrm10010mpCfgXfpIndex | read-only | current | Index definition for the xfp table |
| 1.3.6.1.4.1.20044.54.9.2.3.1.3 | Columnrm10010mpCfgSystConfMsaLinePortn | read-write | current | Default settings on MSA :This register configures the default initialisation settings on MSA |
| 1.3.6.1.4.1.20044.54.9.3 | Noderm10010mpCfgLabels | |||
| 1.3.6.1.4.1.20044.54.9.3.1 | Tablerm10010mpCfgLabelclientTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.54.9.3.1.1 | Rowrm10010mpCfgLabelclientEntry | not-accessible | current | Row definition for the labels table |
| 1.3.6.1.4.1.20044.54.9.3.1.1.1 | Columnrm10010mpCfgLabelclientIndex | read-only | current | Index definition for the labelclient table |
| 1.3.6.1.4.1.20044.54.9.3.1.1.3 | Columnrm10010mpCfgLabelclientPortn | read-write | current | Default settings on the label of the Ports :These registers configures the default initialisation settings of the labels of the ports. |
| 1.3.6.1.4.1.20044.54.9.3.2 | Tablerm10010mpCfgLabellineTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.54.9.3.2.1 | Rowrm10010mpCfgLabellineEntry | not-accessible | current | Row definition for the labels table |
| 1.3.6.1.4.1.20044.54.9.3.2.1.1 | Columnrm10010mpCfgLabellineIndex | read-only | current | Index definition for the labelline table |
| 1.3.6.1.4.1.20044.54.9.3.2.1.3 | Columnrm10010mpCfgLabellinePortn | read-write | current | Default settings on the label of the lines :These registers configures the default initialisation settings of the labels of the lines. |
| 1.3.6.1.4.1.20044.54.9.4 | Noderm10010mpCfgStartuptlh | |||
| 1.3.6.1.4.1.20044.54.9.4.1 | Tablerm10010mpCfgOtxtlhTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.54.9.4.1.1 | Rowrm10010mpCfgOtxtlhEntry | not-accessible | current | Row definition for the startuptlh table |
| 1.3.6.1.4.1.20044.54.9.4.1.1.1 | Columnrm10010mpCfgOtxtlhIndex | read-only | current | Index definition for the otxtlh table |
| 1.3.6.1.4.1.20044.54.9.4.1.1.6 | Columnrm10010mpCfgLinePwrLaserPortn | read-write | current | Defaut Line output Power :This register configures the start-up output power of the Line tranceiver (Unit = dBm) |
| 1.3.6.1.4.1.20044.54.9.4.1.1.7 | Columnrm10010mpCfgLineFCurrentPortn | read-write | current | Default Line transceiver Tx Channel :This register configures the start-up laser channel of the Line Tx transceiver |
| 1.3.6.1.4.1.20044.54.9.4.1.1.8 | Columnrm10010mpCfgLineGridCurrentPortn | read-write | current | Default Line transceiver Grid :This register configures the start-up laser grid of the Line transceiver |
| 1.3.6.1.4.1.20044.54.9.4.1.1.9 | Columnrm10010mpCfgFPortn | read-write | current | Default Line TRX lowest Freq :This register configures the start-up lowest frequency of the Line transceiver |
| 1.3.6.1.4.1.20044.54.9.4.1.1.10 | Columnrm10010mpCfgRxLineFCurrentPortn | read-write | current | Default Line transceiver Rx Channel :This register configures the start-up laser channel of the Line Rx transceiver |
| 1.3.6.1.4.1.20044.54.9.5 | Noderm10010mpCfgOther | |||
| 1.3.6.1.4.1.20044.54.9.5.1 | Noderm10010mptablemoduleOther | |||
| 1.3.6.1.4.1.20044.54.9.5.1.2 | Scalarrm10010mpCfgmode | read-write | current | Default settings on Module :This register selects the configuration mode of the module |
| 1.3.6.1.4.1.20044.54.9.5.1.3 | Scalarrm10010mpCfgfanLowSpeedThreshold | read-write | current | Default settings on Module :This register selects the speed threshold of the fan's |
| 1.3.6.1.4.1.20044.54.9.5.1.4 | Scalarrm10010mpCfgfanHighSpeedThreshold | read-write | current | Default settings on Module :This register selects the speed threshold of the fan's |
| 1.3.6.1.4.1.20044.54.9.6 | Noderm10010mpCfgStartuptablefive | |||
| 1.3.6.1.4.1.20044.54.9.6.1 | Tablerm10010mpCfgOtxtlhcapabilitiesTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.54.9.6.1.1 | Rowrm10010mpCfgOtxtlhcapabilitiesEntry | not-accessible | current | Row definition for the startuptablefive table |
| 1.3.6.1.4.1.20044.54.9.6.1.1.1 | Columnrm10010mpCfgOtxtlhcapabilitiesIndex | read-only | current | Index definition for the otxtlhcapabilities table |
| 1.3.6.1.4.1.20044.54.9.6.1.1.3 | Columnrm10010mpCfgComponentTypePortn | read-only | current | Component parameters :This OID defines the component parameters |
| 1.3.6.1.4.1.20044.54.9.6.1.1.4 | Columnrm10010mpCfgMiscellaneousPortn | read-only | current | Miscellaneous default settings :This OID defines the miscellaneous parameters |
| 1.3.6.1.4.1.20044.54.9.6.1.1.5 | Columnrm10010mpCfgFirstChannelPortn | read-only | current | Number of the first channel of the component :This OID defines the first channel number of the PM |
| 1.3.6.1.4.1.20044.54.9.6.1.1.6 | Columnrm10010mpCfgLastChannelPortn | read-only | current | Number of the last channel of the component :This OID defines the last channel number of the PM |
| 1.3.6.1.4.1.20044.54.9.6.1.1.7 | Columnrm10010mpCfgGridPortn | read-only | current | Grid value of the component :This OID defines the grid of the PM |
| 1.3.6.1.4.1.20044.54.9.257 | Scalarrm10010mpCfgWriteConfiguration | read-write | current | Write configuration to module:This OID writes the complete configuration to the module |
| 1.3.6.1.4.1.20044.54.10 | Noderm10010mptraps | |||
| 1.3.6.1.4.1.20044.54.10.2 | Scalarrm10010mptrapPortNumber | read-only | current | Last port which generates a trap |
| 1.3.6.1.4.1.20044.54.10.3 | Scalarrm10010mptrapLineNumber | read-only | current | Last Line which generates a trap |
| 1.3.6.1.4.1.20044.54.10.4 | Scalarrm10010mptrapBoardNumber | read-only | current | Last module which generates a trap |
| 1.3.6.1.4.1.20044.54.10.30 | Notificationrm10010mpLineTrapNotUrgentGoesOn | current | Not urgent Line default is activated | |
| 1.3.6.1.4.1.20044.54.10.31 | Notificationrm10010mpLineTrapNotUrgentGoesOff | current | Not urgent Line default disappeared | |
| 1.3.6.1.4.1.20044.54.10.32 | Notificationrm10010mpLineTrapUrgentGoesOn | current | Urgent Line default is activated | |
| 1.3.6.1.4.1.20044.54.10.33 | Notificationrm10010mpLineTrapUrgentGoesOff | current | Urgent Line default disappeared | |
| 1.3.6.1.4.1.20044.54.10.34 | Notificationrm10010mpLineTrapCritGoesOn | current | Critical Line default is activated | |
| 1.3.6.1.4.1.20044.54.10.35 | Notificationrm10010mpLineTrapCritGoesOff | current | Critical Line default disappeared | |
| 1.3.6.1.4.1.20044.54.10.40 | Notificationrm10010mpClientTrapNotUrgentGoesOn | current | Not urgent client default is activated | |
| 1.3.6.1.4.1.20044.54.10.41 | Notificationrm10010mpClientTrapNotUrgentGoesOff | current | Not urgent client default disappeared | |
| 1.3.6.1.4.1.20044.54.10.42 | Notificationrm10010mpClientTrapUrgentGoesOn | current | Urgent client default is activated | |
| 1.3.6.1.4.1.20044.54.10.43 | Notificationrm10010mpClientTrapUrgentGoesOff | current | Urgent client default disappeared | |
| 1.3.6.1.4.1.20044.54.10.44 | Notificationrm10010mpClientTrapCritGoesOn | current | Critical client default is activated | |
| 1.3.6.1.4.1.20044.54.10.45 | Notificationrm10010mpClientTrapCritGoesOff | current | Critical client default disappeared | |
| 1.3.6.1.4.1.20044.54.10.50 | Notificationrm10010mpPowerTrapUrgentGoesOn | current | Urgent power supply default is activated | |
| 1.3.6.1.4.1.20044.54.10.51 | Notificationrm10010mpPowerTrapUrgentGoesOff | current | Urgent power supply default disappeared | |
| 1.3.6.1.4.1.20044.54.11 | Noderm10010mpMonitoring | |||
| 1.3.6.1.4.1.20044.54.11.1 | Noderm10010mpMonOther | |||
| 1.3.6.1.4.1.20044.54.11.1.3 | Noderm10010mpMonRmon | |||
| 1.3.6.1.4.1.20044.54.11.2 | Noderm10010mpMonClient | |||
| 1.3.6.1.4.1.20044.54.11.2.4 | Noderm10010mpMonClientRmonCounter | |||
| 1.3.6.1.4.1.20044.54.11.2.4.16 | Tablerm10010mpMonupRmonBytesCounterClientInputTable | not-accessible | current | List of rm10010mpMonupRmonBytesCounterClientInput Article |
| 1.3.6.1.4.1.20044.54.11.2.4.16.1 | Rowrm10010mpMonupRmonBytesCounterClientInputEntry | not-accessible | current | Row definition for the rm10010mpMonupRmonBytesCounterClientInput table |
| 1.3.6.1.4.1.20044.54.11.2.4.16.1.1 | Columnrm10010mpMonupRmonBytesCounterClientInputIndex | read-only | current | Index definition for the rm10010mpMonupRmonBytesCounterClientInput table |
| 1.3.6.1.4.1.20044.54.11.2.4.16.1.2 | Columnrm10010mpMonupRmonBytesCounterClientInputValuePortn | read-only | current | Client Input Bytes :This counter is increased each time a data byte is received on the client port <Help> This counter gives the number of bytes received on th… |
| 1.3.6.1.4.1.20044.54.11.2.4.16.1.3 | Columnrm10010mpMonupRmonBytesCounterClientInputErrorPortn | read-only | current | Bytes Counter Error :This OID when set indicates the Bytes counter value is invalid on client port |
| 1.3.6.1.4.1.20044.54.11.2.4.16.1.4 | Columnrm10010mpMonupRmonBytesCounterClientInputOverloadPortn | read-only | current | Bytes Counter Overload :This OID when set indicates a Bytes counter overload on client port |
| 1.3.6.1.4.1.20044.54.11.2.4.32 | Tablerm10010mpMonupRmonCrcErrorsCounterClientInputTable | not-accessible | current | List of rm10010mpMonupRmonCrcErrorsCounterClientInput Article |
| 1.3.6.1.4.1.20044.54.11.2.4.32.1 | Rowrm10010mpMonupRmonCrcErrorsCounterClientInputEntry | not-accessible | current | Row definition for the rm10010mpMonupRmonCrcErrorsCounterClientInput table |
| 1.3.6.1.4.1.20044.54.11.2.4.32.1.1 | Columnrm10010mpMonupRmonCrcErrorsCounterClientInputIndex | read-only | current | Index definition for the rm10010mpMonupRmonCrcErrorsCounterClientInput table |
| 1.3.6.1.4.1.20044.54.11.2.4.32.1.2 | Columnrm10010mpMonupRmonCrcErrorsCounterClientInputValuePortn | read-only | current | Client Input CRC Errors :This counter is increased each time a B1/CRC error is detected on the client port <Help> This counter gives the number of B1/CRC Error… |
| 1.3.6.1.4.1.20044.54.11.2.4.32.1.3 | Columnrm10010mpMonupRmonCrcErrorsCounterClientInputErrorPortn | read-only | current | CRC Errors Counter Error :This OID when set indicates the CRC Errors counter value is invalid on client port |
| 1.3.6.1.4.1.20044.54.11.2.4.32.1.4 | Columnrm10010mpMonupRmonCrcErrorsCounterClientInputOverloadPortn | read-only | current | CRC Errors Counter Overload :This OID when set indicates a CRC Errors counter overload on client port |
| 1.3.6.1.4.1.20044.54.11.2.4.48 | Tablerm10010mpMonupRmonPacketsCounterClientInputTable | not-accessible | current | List of rm10010mpMonupRmonPacketsCounterClientInput Article |
| 1.3.6.1.4.1.20044.54.11.2.4.48.1 | Rowrm10010mpMonupRmonPacketsCounterClientInputEntry | not-accessible | current | Row definition for the rm10010mpMonupRmonPacketsCounterClientInput table |
| 1.3.6.1.4.1.20044.54.11.2.4.48.1.1 | Columnrm10010mpMonupRmonPacketsCounterClientInputIndex | read-only | current | Index definition for the rm10010mpMonupRmonPacketsCounterClientInput table |
| 1.3.6.1.4.1.20044.54.11.2.4.48.1.2 | Columnrm10010mpMonupRmonPacketsCounterClientInputValuePortn | read-only | current | Client Input Packets :This counter is increased each time a packet is received on the client port <Help> This counter gives the number of packets received on t… |
| 1.3.6.1.4.1.20044.54.11.2.4.48.1.3 | Columnrm10010mpMonupRmonPacketsCounterClientInputErrorPortn | read-only | current | Packets Counter Error :This OID when set indicates the Packets counter value is invalid on client port |
| 1.3.6.1.4.1.20044.54.11.2.4.48.1.4 | Columnrm10010mpMonupRmonPacketsCounterClientInputOverloadPortn | read-only | current | Packets Counter Overload :This OID when set indicates a Packets counter overload on client port |
| 1.3.6.1.4.1.20044.54.11.2.4.64 | Tablerm10010mpMonupRmonBroadcastCounterClientInputTable | not-accessible | current | List of rm10010mpMonupRmonBroadcastCounterClientInput Article |
| 1.3.6.1.4.1.20044.54.11.2.4.64.1 | Rowrm10010mpMonupRmonBroadcastCounterClientInputEntry | not-accessible | current | Row definition for the rm10010mpMonupRmonBroadcastCounterClientInput table |
| 1.3.6.1.4.1.20044.54.11.2.4.64.1.1 | Columnrm10010mpMonupRmonBroadcastCounterClientInputIndex | read-only | current | Index definition for the rm10010mpMonupRmonBroadcastCounterClientInput table |
| 1.3.6.1.4.1.20044.54.11.2.4.64.1.2 | Columnrm10010mpMonupRmonBroadcastCounterClientInputValuePortn | read-only | current | Client Input Broadcast Packets :This counter is increased each time a broadcast packet is received on the client port <Help> This counter gives the number of B… |
| 1.3.6.1.4.1.20044.54.11.2.4.64.1.3 | Columnrm10010mpMonupRmonBroadcastCounterClientInputErrorPortn | read-only | current | Broadcast Counter Error :This OID when set indicates the Broadcast counter value is invalid on client port |
| 1.3.6.1.4.1.20044.54.11.2.4.64.1.4 | Columnrm10010mpMonupRmonBroadcastCounterClientInputOverloadPortn | read-only | current | Broadcast Counter Overload :This OID when set indicates a Broadcast counter overload on client port |
| 1.3.6.1.4.1.20044.54.11.2.4.80 | Tablerm10010mpMonupRmonMulticastCounterClientInputTable | not-accessible | current | List of rm10010mpMonupRmonMulticastCounterClientInput Article |
| 1.3.6.1.4.1.20044.54.11.2.4.80.1 | Rowrm10010mpMonupRmonMulticastCounterClientInputEntry | not-accessible | current | Row definition for the rm10010mpMonupRmonMulticastCounterClientInput table |
| 1.3.6.1.4.1.20044.54.11.2.4.80.1.1 | Columnrm10010mpMonupRmonMulticastCounterClientInputIndex | read-only | current | Index definition for the rm10010mpMonupRmonMulticastCounterClientInput table |
| 1.3.6.1.4.1.20044.54.11.2.4.80.1.2 | Columnrm10010mpMonupRmonMulticastCounterClientInputValuePortn | read-only | current | Client Input Multicast Packets :This counter is increased each time a Multicast packet is received on the client port <Help> This counter gives the number of M… |
| 1.3.6.1.4.1.20044.54.11.2.4.80.1.3 | Columnrm10010mpMonupRmonMulticastCounterClientInputErrorPortn | read-only | current | Multicast Counter Error :This OID when set indicates the Multicast counter value is invalid on client port |
| 1.3.6.1.4.1.20044.54.11.2.4.80.1.4 | Columnrm10010mpMonupRmonMulticastCounterClientInputOverloadPortn | read-only | current | Multicast Counter Overload :This OID when set indicates a Multicast counter overload on client port |
| 1.3.6.1.4.1.20044.54.11.2.4.96 | Tablerm10010mpMonupRmonPauseFrameCounterClientInputTable | not-accessible | current | List of rm10010mpMonupRmonPauseFrameCounterClientInput Article |
| 1.3.6.1.4.1.20044.54.11.2.4.96.1 | Rowrm10010mpMonupRmonPauseFrameCounterClientInputEntry | not-accessible | current | Row definition for the rm10010mpMonupRmonPauseFrameCounterClientInput table |
| 1.3.6.1.4.1.20044.54.11.2.4.96.1.1 | Columnrm10010mpMonupRmonPauseFrameCounterClientInputIndex | read-only | current | Index definition for the rm10010mpMonupRmonPauseFrameCounterClientInput table |
| 1.3.6.1.4.1.20044.54.11.2.4.96.1.2 | Columnrm10010mpMonupRmonPauseFrameCounterClientInputValuePortn | read-only | current | Client Input Pause Frames :This counter is increased each time a Pause frame is received on the client port <Help> This counter gives the number of Pause frame… |
| 1.3.6.1.4.1.20044.54.11.2.4.96.1.3 | Columnrm10010mpMonupRmonPauseFrameCounterClientInputErrorPortn | read-only | current | Pause Counter Error :This OID when set indicates the Pause counter value is invalid on client port |
| 1.3.6.1.4.1.20044.54.11.2.4.96.1.4 | Columnrm10010mpMonupRmonPauseFrameCounterClientInputOverloadPortn | read-only | current | Pause Counter Overload :This OID when set indicates a Pause counter overload on client port |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| Rm10010mpAdjustValue | INTEGER { otxadjustvalue0(0), otxadjustvalue1(1), otxadjustvalue2(2), otxadjustvalue3(3), otxadjustvalue4(4), otxadjustvalue5(5), otxadjustvalue6(6), otxadjustvalue7(7), otxadjustvalue8(8), otxadjustvalue9(9), otxadjustvalue10(10) } | current | Different values in Adjust mode on OTX-TLH on client and line ports |
| Rm10010mpClientProtocol | INTEGER { protocolclientvalue0(0), protocolclientvalue1(1), protocolclientvalue2(2), protocolclientvalue3(3), protocolclientvalue4(4), protocolclientvalue5(5), protocolclientvalue6(6), protocolclientvalue7(7), protocolclientvalue8(8) } | current | Different values on the protocol on the client ports |
| Rm10010mpMultiRate | INTEGER { rate100Mhz(0), rate250Mhz(1), rate500Mhz(2), rate1Ghz(3) } | current | different rate for a client port |
| Rm10010mpOrxChannel | INTEGER | current | Channel selection on transceiver Rx line ports |
| Rm10010mpOtxChannel | INTEGER | current | Channel selection on transceiver Tx line ports |
| Rm10010mpOtxGrid | INTEGER { otxgrid200(200), otxgrid100(100), otxgrid50(50) } | current | Different grids on OTX-TLH on client and line ports |
| Rm10010mpOtxMode | INTEGER { otx80mode(1), otx60mode(2), otxadjustmode(4) } | current | Different modes on OTX-TLH on client and line ports |
| Rm10010mpProtocolMode | INTEGER { protocolmodevalue0(0), protocolmodevalue1(1), protocolmodevalue2(2), protocolmodevalue3(3) } | current | Different values on the protocol mode |