EKINOPS-Rmoac17ilwb-MIB
317 objects
Creation
Imported Objects
| EKINOPS-MIB | EkiApiState EkiMeasureType EkiMode ekinops EkiOnOff EkiProtocol EkiState EkiSynchroMode |
| SNMPv2-SMI | Counter32 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.20044.110 | Identitymodulermoac17ilwb | Creation | ||
| 1.3.6.1.4.1.20044.110.2 | Nodermoac17ilwbalarms | |||
| 1.3.6.1.4.1.20044.110.2.1 | Nodermoac17ilwbAlmOther | |||
| 1.3.6.1.4.1.20044.110.2.1.1 | Nodermoac17ilwbAlmOtherNurg | |||
| 1.3.6.1.4.1.20044.110.2.1.1.2 | Nodermoac17ilwbAlmsynthAlm2 | |||
| 1.3.6.1.4.1.20044.110.2.1.1.2.1 | Scalarrmoac17ilwbAlmConfTableSave | read-only | current | PM Configuration Save :This OID is at 1 during the saving of a new configuration table in the module Flash memory. <Condtype> CONF_TABLE_SAVE <Probcause> other… |
| 1.3.6.1.4.1.20044.110.2.1.1.2.2 | Scalarrmoac17ilwbAlmInvUpload | read-only | current | Inventory Upload :This OID is at 1 during the uploading of PM inventory information. <Condtype> INV_UPLOAD <Probcause> other (1) <Alarmtype> other (1) <Polarit… |
| 1.3.6.1.4.1.20044.110.2.1.1.2.3 | Scalarrmoac17ilwbAlmConfTableLoad | read-only | current | PM Configuration Load :This OID is at 1 during the loading of configuration tables in the modules RAM. <Condtype> CONF_TABLE_LOAD <Probcause> other (1) <Alarmt… |
| 1.3.6.1.4.1.20044.110.2.1.1.75 | Nodermoac17ilwbAlmfoaWarnings | |||
| 1.3.6.1.4.1.20044.110.2.1.1.75.7 | Scalarrmoac17ilwbAlmTermpLowWarning | read-only | current | Temperature Low Warning :This OID indicates that the PM temperature if lower than the Warning threshold <Condtype> TERMP_LOW_WARNING <Probcause> temperatureUna… |
| 1.3.6.1.4.1.20044.110.2.1.1.75.8 | Scalarrmoac17ilwbAlmTempHighWarning | read-only | current | Temperature High Warning :This OID indicates that the PM temperature if higher than the Warning threshold <Condtype> TEMP_HIGH_WARNING <Probcause> temperatureU… |
| 1.3.6.1.4.1.20044.110.2.1.2 | Nodermoac17ilwbAlmOtherUrg | |||
| 1.3.6.1.4.1.20044.110.2.1.2.74 | Nodermoac17ilwbAlmfoaAlarms | |||
| 1.3.6.1.4.1.20044.110.2.1.2.74.7 | Scalarrmoac17ilwbAlmTermpLowAlarm | read-only | current | Temperature Low Alarm :This OID indicates that the PM temperature if lower than the alarm threshold <Condtype> TERMP_LOW_ALARM <Probcause> temperatureUnaccepta… |
| 1.3.6.1.4.1.20044.110.2.1.2.74.8 | Scalarrmoac17ilwbAlmTempHighAlarm | read-only | current | Temperature High Alarm :This OID indicates that the PM temperature is higher than the alarm threshold <Condtype> TEMP_HIGH_ALARM <Probcause> temperatureUnaccep… |
| 1.3.6.1.4.1.20044.110.2.1.3 | Nodermoac17ilwbAlmOtherCrit | |||
| 1.3.6.1.4.1.20044.110.2.1.3.0 | Nodermoac17ilwbAlmsynthAlm0 | |||
| 1.3.6.1.4.1.20044.110.2.1.3.0.1 | Scalarrmoac17ilwbAlmMaintenanceMode | read-only | current | Maintenance Mode :This OID indicates that the PM is in maintenance mode <Help> This status indiates if the module is currently in maintenance mode <Condtype> M… |
| 1.3.6.1.4.1.20044.110.2.1.3.0.2 | Scalarrmoac17ilwbAlmAprOn | read-only | current | Automatic Power Reduction :This OID indicates that the APR algorithm has been operated and the output of the lasers are shutdown <Help> The APR algorithm has b… |
| 1.3.6.1.4.1.20044.110.2.1.3.0.9 | Scalarrmoac17ilwbAlmModGlobFail | read-only | current | Module Failure :This OID is set on detection of a failure originating from the PM <Condtype> MOD_GLOB_FAIL <Probcause> equipmentMalfunction (16) <Alarmtype> sy… |
| 1.3.6.1.4.1.20044.110.2.1.3.0.10 | Scalarrmoac17ilwbAlmUpEdfaInitNotCompl | read-only | current | IL1 Not Initialized :This OID indicates that the initialisation of the IL1 is not completed <Help> This status indicates if the IL1 has been correctly initiali… |
| 1.3.6.1.4.1.20044.110.2.1.3.0.11 | Scalarrmoac17ilwbAlmDwEdfaInitNotCompl | read-only | current | IL2 Not Initialized :This OID indicates that the initialisation of the IL2 is not completed <Help> This status indicates if the IL2 has been correctly initiali… |
| 1.3.6.1.4.1.20044.110.2.1.3.0.12 | Scalarrmoac17ilwbAlmExtPump1NotLocked | read-only | current | External Pump Not Detected :This OID indicates that the first external pump is not detected by the amplifier module <Help> This alarm indicates if the external… |
| 1.3.6.1.4.1.20044.110.2.1.3.0.15 | Scalarrmoac17ilwbAlmDefFuseA | read-only | current | Fuse A Fail :This OID indicates that the fuse of the power input A is in fail condition <Help> Status of the Fuse A <Condtype> DEF_FUSE_A <Probcause> powerProb… |
| 1.3.6.1.4.1.20044.110.2.1.3.0.16 | Scalarrmoac17ilwbAlmDefFuseB | read-only | current | Fuse B Fail :This OID indicates that the fuse of the power input B is in fail condition <Help> Status of the Fuse B <Condtype> DEF_FUSE_B <Probcause> powerProb… |
| 1.3.6.1.4.1.20044.110.2.2 | Nodermoac17ilwbAlmClient | |||
| 1.3.6.1.4.1.20044.110.2.2.1 | Nodermoac17ilwbAlmClientNurg | |||
| 1.3.6.1.4.1.20044.110.2.2.1.33 | Nodermoac17ilwbAlmclientEdfaWarnings | |||
| 1.3.6.1.4.1.20044.110.2.2.1.33.1 | Scalarrmoac17ilwbAlmClientGainLowWarning | read-only | current | IL2 Gain Low Warning :This OID indicates that the Gain is lower than the Warning threshold of the IL2 Module <Help> This alarm indicates if the IL2 gain is too… |
| 1.3.6.1.4.1.20044.110.2.2.1.33.2 | Scalarrmoac17ilwbAlmClientGainHighWarning | read-only | current | IL2 Gain High Warning :This OID indicates that the Gain is higher than the Warning threshold of the IL2 Module <Help> This alarm indicates if the IL2 gain is t… |
| 1.3.6.1.4.1.20044.110.2.2.1.33.3 | Scalarrmoac17ilwbAlmClientInputPwrLowWarning | read-only | current | IL2 Rx Pwr Low Warning :This OID indicates that the Receive Power is lower than the Warning threshold of the IL2 Optical Module <Help> This warning indicates i… |
| 1.3.6.1.4.1.20044.110.2.2.1.33.4 | Scalarrmoac17ilwbAlmClientInputPwrHighWarning | read-only | current | IL2 Rx Pwr High Warning :This OID indicates that the Receive Power is higher than the Warning threshold of the IL2 Optical Module <Help> This warning indicates… |
| 1.3.6.1.4.1.20044.110.2.2.1.33.5 | Scalarrmoac17ilwbAlmClientOutputPwrLowWarning | read-only | current | IL2 Tx Pwr Low Warning :This OID indicates that the Transmit Power is lower than the Warning threshold of the IL2 Optical Module <Help> This warning indicates … |
| 1.3.6.1.4.1.20044.110.2.2.1.33.6 | Scalarrmoac17ilwbAlmClientOutputPwrHighWarning | read-only | current | IL2 Tx Pwr High Warning :This OID indicates that the Transmit Power is higher than the Warning threshold of the IL2 Optical Module <Help> This warning indicate… |
| 1.3.6.1.4.1.20044.110.2.2.1.33.7 | Scalarrmoac17ilwbAlmClientBiasLowWarning | read-only | current | IL2 Bias Low Warning :This OID indicates that the Bias is lower than the Warning threshold of the IL2 Optical Module <Help> This warning indicates if the IL2 b… |
| 1.3.6.1.4.1.20044.110.2.2.1.33.8 | Scalarrmoac17ilwbAlmClientBiasHighWarning | read-only | current | IL2 Bias High Warning :This OID indicates that the Bias is higher than the Warning threshold of the IL2 Optical Module <Help> This warning indicates if the IL2… |
| 1.3.6.1.4.1.20044.110.2.2.2 | Nodermoac17ilwbAlmClientUrg | |||
| 1.3.6.1.4.1.20044.110.2.2.2.32 | Nodermoac17ilwbAlmclientEdfaAlarms1 | |||
| 1.3.6.1.4.1.20044.110.2.2.2.32.1 | Scalarrmoac17ilwbAlmClientGainLowAlarm | read-only | current | IL2 Gain Low Alarm :This OID indicates that the Gain is lower than the alarm threshold of the IL2 Module <Help> This alarm indicates if the IL2 gain is too low… |
| 1.3.6.1.4.1.20044.110.2.2.2.32.2 | Scalarrmoac17ilwbAlmClientGainHighAlarm | read-only | current | IL2 Gain High Alarm :This OID indicates that the Gain is higher than the alarm threshold of the IL2 Module <Help> This alarm indicates if the IL2 gain is too h… |
| 1.3.6.1.4.1.20044.110.2.2.2.32.3 | Scalarrmoac17ilwbAlmClientInputPwrLowAlarm | read-only | current | IL2 Rx Pwr Low Alarm :This OID indicates that the Receive Power is lower than the alarm threshold of the IL2 Optical Module <Help> This alarm indicates if the … |
| 1.3.6.1.4.1.20044.110.2.2.2.32.4 | Scalarrmoac17ilwbAlmClientInputPwrHighAlarm | read-only | current | IL2 Rx Pwr High Alarm :This OID indicates that the Receive Power is higher than the alarm threshold of the IL2 Optical Module <Help> This alarm indicates if th… |
| 1.3.6.1.4.1.20044.110.2.2.2.32.5 | Scalarrmoac17ilwbAlmClientOutputPwrLowAlarm | read-only | current | IL2 Tx Pwr Low Alarm :This OID indicates that the Transmit Power is lower than the alarm threshold of the IL2 Optical Module <Help> This alarm indicates if the… |
| 1.3.6.1.4.1.20044.110.2.2.2.32.6 | Scalarrmoac17ilwbAlmClientOutputPwrHighAlarm | read-only | current | IL2 Tx Pwr High Alarm :This OID indicates that the Transmit Power is higher than the alarm threshold of the IL2 Optical Module <Help> This alarm indicates if t… |
| 1.3.6.1.4.1.20044.110.2.2.2.32.7 | Scalarrmoac17ilwbAlmClientBiasLowAlarm | read-only | current | IL2 Bias Low Alarm :This OID indicates that the Bias is lower than the alarm threshold of the IL2 Optical Module <Help> This alarm indicates if the IL2 bias is… |
| 1.3.6.1.4.1.20044.110.2.2.2.32.8 | Scalarrmoac17ilwbAlmClientBiasHighAlarm | read-only | current | IL2 Bias High Alarm :This OID indicates that the Bias is higher than the alarm threshold of the IL2 Optical Module <Help> This alarm indicates if the IL2 bias … |
| 1.3.6.1.4.1.20044.110.2.2.3 | Nodermoac17ilwbAlmClientCrit | |||
| 1.3.6.1.4.1.20044.110.2.2.3.8 | Nodermoac17ilwbAlmsynthAlm8 | |||
| 1.3.6.1.4.1.20044.110.2.2.3.8.4 | Scalarrmoac17ilwbAlmClientHwFail | read-only | current | Client Port HW Failure :This OID indicates a failure on Client port, most probably caused by a HW issue <Condtype> CLIENT_HW_FAIL <Probcause> equipmentMalfunct… |
| 1.3.6.1.4.1.20044.110.2.2.3.8.5 | Scalarrmoac17ilwbAlmClientTxOff | read-only | current | IL2 Optical Output Shutdown :This OID indicates the IL2 optical output power is on <Help> This status indicates if the IL2 laser pump transceiver laser is ON o… |
| 1.3.6.1.4.1.20044.110.2.2.3.8.9 | Scalarrmoac17ilwbAlmClientDdmWarning | read-only | current | Warning On IL2 DDM :This OID indicates a warning is present coming out of the IL2 DDM <Help> This alarm indicates if a DDM Warning has been detected on the IL2… |
| 1.3.6.1.4.1.20044.110.2.2.3.8.10 | Scalarrmoac17ilwbAlmClientDdmAlm | read-only | current | Alarm On IL2 DDM :This OID indicates an alarm is present coming out of the Pre_Amp DDM <Help> This alarm indicates if a DDM Alarm has been detected on the IL2 … |
| 1.3.6.1.4.1.20044.110.2.2.3.8.12 | Scalarrmoac17ilwbAlmClientFail | read-only | current | Client Port Failure :This OID indicates a failure on the Client port <Condtype> CLIENT_FAIL <Probcause> bandwidthReduced(4) <Alarmtype> synthesisAlarm (12) <Po… |
| 1.3.6.1.4.1.20044.110.2.2.3.8.13 | Scalarrmoac17ilwbAlmClientExtPumpFail | read-only | current | IL2 External Pump Fail :This OID indicates that the external pump linked to the IL2 is in fail condition <Help> This alarm indicates if the external pump linke… |
| 1.3.6.1.4.1.20044.110.2.2.3.8.14 | Scalarrmoac17ilwbAlmSupvbFail | read-only | current | : <Condtype> SUPVB_FAIL <Probcause> equipmentMalfunction (16) <Alarmtype> equipmentAlarm (5) <Polarity> (2) |
| 1.3.6.1.4.1.20044.110.2.2.3.35 | Nodermoac17ilwbAlmclientEdfaAlarms2 | |||
| 1.3.6.1.4.1.20044.110.2.2.3.35.1 | Scalarrmoac17ilwbAlmClientEdfaNr | read-only | current | IL2 Optical Module Not Ready :This OID indicates that the IL2 Optical Module is not ready <Help> This status indicates if the IL2 has been correctly initialize… |
| 1.3.6.1.4.1.20044.110.2.2.3.35.2 | Scalarrmoac17ilwbAlmClientEdfaTecFail | read-only | current | IL2 TEC Fail :This OID indicates that the TEC is in fail condition on the IL2 Optical Module <Help> This alarm indicates if the TEC of the IL2 is in fail condi… |
| 1.3.6.1.4.1.20044.110.2.2.3.35.3 | Scalarrmoac17ilwbAlmClientEdfaLaserFail | read-only | current | IL2 Pump Laser Fail :This OID indicates a Transmit Laser Fail on the IL2 Optical Module <Help> This alarm indicates if the laser of the IL2 is in fail conditio… |
| 1.3.6.1.4.1.20044.110.2.2.3.35.4 | Scalarrmoac17ilwbAlmClientEdfaLos | read-only | current | IL2 Loss Of Signal :This OID indicates a Loss of Signal on the IL2 Optical Module <Help> This alarm indicates if an optical signal is detected on the IL2 input… |
| 1.3.6.1.4.1.20044.110.2.2.3.35.5 | Scalarrmoac17ilwbAlmClientExtPumpEdfaLowCurrent | read-only | current | IL2 Pump Low Current :This OID indicates that the EDFA pump current of IL2 is too low because of the external pump high power<Help> This alarm (only active whe… |
| 1.3.6.1.4.1.20044.110.2.2.3.35.6 | Scalarrmoac17ilwbAlmClientGainOutOfRange | read-only | current | IL2 Gain Out Of Range :This OID indicates the target gain of the IL2 is out of range (18-32dB), the flatness of the IL1 is not guaranteed.<Help> This alarm ind… |
| 1.3.6.1.4.1.20044.110.2.2.3.37 | Nodermoac17ilwbAlmclientMsaAlarms | |||
| 1.3.6.1.4.1.20044.110.2.2.3.37.1 | Scalarrmoac17ilwbAlmClientMsaLos | read-only | current | IL2 MSA Loss Of Signal :This OID indicates a Loss of Signal is detected on the Mid Stage Access of the IL2 EDFAThis alarm indicates a Loss of Signal is detecte… |
| 1.3.6.1.4.1.20044.110.2.2.3.37.2 | Scalarrmoac17ilwbAlmClientMsaAttenuation | read-only | current | IL2 MSA Attenuation Alarm :This OID indicates the attenuation on the IL2 Mid Stage access has changed.This alarm indicates the attenuation on the IL2 Mid Stage… |
| 1.3.6.1.4.1.20044.110.2.3 | Nodermoac17ilwbAlmLine | |||
| 1.3.6.1.4.1.20044.110.2.3.1 | Nodermoac17ilwbAlmLineNurg | |||
| 1.3.6.1.4.1.20044.110.2.3.1.41 | Nodermoac17ilwbAlmlineEdfaWarnings | |||
| 1.3.6.1.4.1.20044.110.2.3.1.41.1 | Scalarrmoac17ilwbAlmLineGainLowWarning | read-only | current | IL1 Gain Low Warning :This OID indicates that the Gain is lower than the Warning threshold of the IL1 Module <Help> This alarm indicates if the IL1 gain is too… |
| 1.3.6.1.4.1.20044.110.2.3.1.41.2 | Scalarrmoac17ilwbAlmLineGainHighWarning | read-only | current | IL1 Gain High Warning :This OID indicates that the Gain is higher than the Warning threshold of the IL1 Module <Help> This alarm indicates if the IL1 gain is t… |
| 1.3.6.1.4.1.20044.110.2.3.1.41.3 | Scalarrmoac17ilwbAlmLineInputPwrLowWarning | read-only | current | IL1 Rx Pwr Low Warning :This OID indicates that the Receive Power is lower than the Warning threshold of the IL1 Optical Module <Help> This warning indicates i… |
| 1.3.6.1.4.1.20044.110.2.3.1.41.4 | Scalarrmoac17ilwbAlmLineInputPwrHighWarning | read-only | current | IL1 Rx Pwr High Warning :This OID indicates that the Receive Power is higher than the Warning threshold of the IL1 Optical Module <Help> This warning indicates… |
| 1.3.6.1.4.1.20044.110.2.3.1.41.5 | Scalarrmoac17ilwbAlmLineOutputPwrLowWarning | read-only | current | IL1 Tx Pwr Low Warning :This OID indicates that the Transmit Power is lower than the Warning threshold of the IL1 Optical Module <Help> This warning indicates … |
| 1.3.6.1.4.1.20044.110.2.3.1.41.6 | Scalarrmoac17ilwbAlmLineOutputPwrHighWarning | read-only | current | IL1 Tx Pwr High Warning :This OID indicates that the Transmit Power is higher than the Warning threshold of the IL1 Optical Module <Help> This warning indicate… |
| 1.3.6.1.4.1.20044.110.2.3.1.41.7 | Scalarrmoac17ilwbAlmLineBiasLowWarning | read-only | current | IL1 Bias Low Warning :This OID indicates that the Bias is lower than the Warning threshold of the IL1 Optical Module <Help> This warning indicates if the IL1 b… |
| 1.3.6.1.4.1.20044.110.2.3.1.41.8 | Scalarrmoac17ilwbAlmLineBiasHighWarning | read-only | current | IL1 Bias High Warning :This OID indicates that the Bias is higher than the Warning threshold of the IL1 Optical Module <Help> This warning indicates if the IL1… |
| 1.3.6.1.4.1.20044.110.2.3.2 | Nodermoac17ilwbAlmLineUrg | |||
| 1.3.6.1.4.1.20044.110.2.3.2.40 | Nodermoac17ilwbAlmlineEdfaAlarms1 | |||
| 1.3.6.1.4.1.20044.110.2.3.2.40.1 | Scalarrmoac17ilwbAlmLineGainLowAlarm | read-only | current | IL1 Gain Low Alarm :This OID indicates that the Gain is lower than the alarm threshold of the IL1 Module <Help> This alarm indicates if the IL1 gain is too low… |
| 1.3.6.1.4.1.20044.110.2.3.2.40.2 | Scalarrmoac17ilwbAlmLineGainHighAlarm | read-only | current | IL1 Gain High Alarm :This OID indicates that the Gain is higher than the alarm threshold of the IL1 Module <Help> This alarm indicates if the IL1 gain is too h… |
| 1.3.6.1.4.1.20044.110.2.3.2.40.3 | Scalarrmoac17ilwbAlmLineInputPwrLowAlarm | read-only | current | IL1 Rx Pwr Low Alarm :This OID indicates that the Receive Power is lower than the alarm threshold of the IL1 Optical Module <Help> This alarm indicates if the … |
| 1.3.6.1.4.1.20044.110.2.3.2.40.4 | Scalarrmoac17ilwbAlmLineInputPwrHighAlarm | read-only | current | IL1 Rx Pwr High Alarm :This OID indicates that the Receive Power is higher than the alarm threshold of the IL1 Optical Module <Help> This alarm indicates if th… |
| 1.3.6.1.4.1.20044.110.2.3.2.40.5 | Scalarrmoac17ilwbAlmLineOutputPwrLowAlarm | read-only | current | IL1 Tx Pwr Low Alarm :This OID indicates that the Transmit Power is lower than the alarm threshold of the IL1 Optical Module <Help> This alarm indicates if the… |
| 1.3.6.1.4.1.20044.110.2.3.2.40.6 | Scalarrmoac17ilwbAlmLineOutputPwrHighAlarm | read-only | current | IL1 Tx Pwr High Alarm :This OID indicates that the Transmit Power is higher than the alarm threshold of the IL1 Optical Module <Help> This alarm indicates if t… |
| 1.3.6.1.4.1.20044.110.2.3.2.40.7 | Scalarrmoac17ilwbAlmLineBiasLowAlarm | read-only | current | IL1 Bias Low Alarm :This OID indicates that the Bias is lower than the alarm threshold of the IL1 Optical Module <Help> This alarm indicates if the IL1 bias is… |
| 1.3.6.1.4.1.20044.110.2.3.2.40.8 | Scalarrmoac17ilwbAlmLineBiasHighAlarm | read-only | current | IL1 Bias High Alarm :This OID indicates that the Bias is higher than the alarm threshold of the IL1 Optical Module <Help> This alarm indicates if the IL1 bias … |
| 1.3.6.1.4.1.20044.110.2.3.3 | Nodermoac17ilwbAlmLineCrit | |||
| 1.3.6.1.4.1.20044.110.2.3.3.7 | Nodermoac17ilwbAlmsynthAlm7 | |||
| 1.3.6.1.4.1.20044.110.2.3.3.7.4 | Scalarrmoac17ilwbAlmLineHwFail | read-only | current | Line Port HW Failure :This OID indicates a failure on line port, most probably caused by a HW issue <Condtype> LINE_HW_FAIL <Probcause> equipmentMalfunction (1… |
| 1.3.6.1.4.1.20044.110.2.3.3.7.5 | Scalarrmoac17ilwbAlmLineTxOff | read-only | current | IL1 Optical Output Shutdown :This OID indicates the IL1 optical output power is on <Help> This status indicates if the IL1 laser pump is ON or OFF <Condtype> L… |
| 1.3.6.1.4.1.20044.110.2.3.3.7.9 | Scalarrmoac17ilwbAlmLineDdmWarning | read-only | current | Warning On IL1 DDM :This OID indicates a warning is present coming out of the IL1 DDM <Help> This alarm indicates if a DDM Warning has been detected on the IL1… |
| 1.3.6.1.4.1.20044.110.2.3.3.7.10 | Scalarrmoac17ilwbAlmLineDdmAlm | read-only | current | Alarm On IL1 DDM :This OID indicates an alarm is present coming out of the IL1 DDM <Help> This alarm indicates if a DDM Alarm has been detected on the IL1 <Con… |
| 1.3.6.1.4.1.20044.110.2.3.3.7.12 | Scalarrmoac17ilwbAlmLineFail | read-only | current | Line Port Failure :This OID indicates a failure on the line port <Condtype> LINE_FAIL <Probcause> callEstablishmentError(5) <Alarmtype> synthesisAlarm (12) <Po… |
| 1.3.6.1.4.1.20044.110.2.3.3.7.13 | Scalarrmoac17ilwbAlmLineExtPumpFail | read-only | current | IL1 External Pump Fail :This OID indicates that the external pump linked to the IL1 is in fail condition <Help> This alarm indicates if the external pump linke… |
| 1.3.6.1.4.1.20044.110.2.3.3.7.14 | Scalarrmoac17ilwbAlmSupvaFail | read-only | current | : <Condtype> SUPVA_FAIL <Probcause> equipmentMalfunction (16) <Alarmtype> equipmentAlarm (5) <Polarity> (2) |
| 1.3.6.1.4.1.20044.110.2.3.3.43 | Nodermoac17ilwbAlmlineEdfaAlarms2 | |||
| 1.3.6.1.4.1.20044.110.2.3.3.43.1 | Scalarrmoac17ilwbAlmLineEdfaNr | read-only | current | IL1 Optical Module Not Ready :This OID indicates that the IL1 Optical Module is not ready <Help> This status indicates if the IL1 has been correctly initialize… |
| 1.3.6.1.4.1.20044.110.2.3.3.43.2 | Scalarrmoac17ilwbAlmLineEdfaTecFail | read-only | current | IL1 TEC Fail :This OID indicates that the TEC is in fail condition on the IL1 Optical Module <Help> This alarm indicates if the TEC of the IL1 is in fail condi… |
| 1.3.6.1.4.1.20044.110.2.3.3.43.3 | Scalarrmoac17ilwbAlmLineEdfaLaserFail | read-only | current | IL1 Pump Laser Fail :This OID indicates a Transmit Laser Fail on the IL1 Optical Module <Help> This alarm indicates if the laser of the IL1 is in fail conditio… |
| 1.3.6.1.4.1.20044.110.2.3.3.43.4 | Scalarrmoac17ilwbAlmLineEdfaLos | read-only | current | IL1 Loss Of Signal :This OID indicates a Loss of Signal on the IL1 Optical Module <Help> This alarm indicates if an optical signal is detected on the IL1 input… |
| 1.3.6.1.4.1.20044.110.2.3.3.43.5 | Scalarrmoac17ilwbAlmLineExtPumpEdfaLowCurrent | read-only | current | IL1 Pump Low Current :This OID indicates that the EDFA pump current of IL1 is too low because of the external pump high power<Help> This alarm (only active whe… |
| 1.3.6.1.4.1.20044.110.2.3.3.43.6 | Scalarrmoac17ilwbAlmLineGainOutOfRange | read-only | current | IL1 Gain Out Of Range :This OID indicates the target gain of the IL1 is out of range (10-18dB), the flatness of the IL1 is not guaranteed.<Help> This alarm ind… |
| 1.3.6.1.4.1.20044.110.2.3.3.45 | Nodermoac17ilwbAlmlineMsaAlarms | |||
| 1.3.6.1.4.1.20044.110.2.3.3.45.1 | Scalarrmoac17ilwbAlmLineMsaLos | read-only | current | IL1 MSA Loss Of Signal :This OID indicates a Loss of Signal is detected on the Mid Stage Access of the IL1 EDFAThis alarm indicates a Loss of Signal is detecte… |
| 1.3.6.1.4.1.20044.110.2.3.3.45.2 | Scalarrmoac17ilwbAlmLineMsaAttenuation | read-only | current | IL1 MSA Attenuation Alarm :This OID indicates the attenuation on the IL1 Mid Stage access has changed.This alarm indicates the attenuation on the IL2 Mid Stage… |
| 1.3.6.1.4.1.20044.110.2.3.3.48 | Tablermoac17ilwbAlmlineOscAlarmsTable | not-accessible | current | List of rmoac17ilwbAlmlineOscAlarms Article |
| 1.3.6.1.4.1.20044.110.2.3.3.48.1 | Rowrmoac17ilwbAlmlineOscAlarmsEntry | not-accessible | current | Row definition for the rmoac17ilwbAlmlineOscAlarms table |
| 1.3.6.1.4.1.20044.110.2.3.3.48.1.1 | Columnrmoac17ilwbAlmlineOscAlarmsIndex | read-only | current | Index definition for the rmoac17ilwbAlmlineOscAlarms table |
| 1.3.6.1.4.1.20044.110.2.3.3.48.1.2 | Columnrmoac17ilwbAlmLineLosPortn | read-only | current | OSC Loss Of Signal :This OID indicates that no signal is present on the OSC <Help> This alarms indicates that no signal is present on the OSC <Condtype> LINE_L… |
| 1.3.6.1.4.1.20044.110.2.3.3.48.1.3 | Columnrmoac17ilwbAlmLineTxOffPortn | read-only | current | OSC Optical Output Shutdown :This OID indicates the optical output power is shutdown on OSC<Help> This alarm indicates the optical output power is shutdown on … |
| 1.3.6.1.4.1.20044.110.2.3.3.48.1.4 | Columnrmoac17ilwbAlmLineTxFailPortn | read-only | current | OSC Tx Fail :This OID indicates the OSC Laser is in fail condition<Help> This alarm indicates the OSC Laser is in fail condition <Condtype> LINE_TX_FAIL_1 <Pro… |
| 1.3.6.1.4.1.20044.110.2.3.3.48.1.6 | Columnrmoac17ilwbAlmLineOosPortn | read-only | current | OSC In Service :This OID indicates that the OSC is In Service (1) or Out or Service (2)<Help> This status indicates that the OSC is In Service or Out or Servic… |
| 1.3.6.1.4.1.20044.110.2.3.3.48.1.10 | Columnrmoac17ilwbAlmLineWarningPortn | read-only | current | OSC DDM Warning :This OID indicates a warning is present on OSC Tx power, Receive power or temperature<Help> This alarm indicates a warning is present on OSC T… |
| 1.3.6.1.4.1.20044.110.2.3.3.48.1.11 | Columnrmoac17ilwbAlmLineAlmPortn | read-only | current | OSC DDM Alarm :This alarm indicates an alarm is present on OSC Tx power, Rx power or temperature <Help> This alarm indicates an alarm is present on OSC Tx powe… |
| 1.3.6.1.4.1.20044.110.2.3.3.49 | Tablermoac17ilwbAlmlineOscThresholdAlarmsTable | not-accessible | current | List of rmoac17ilwbAlmlineOscThresholdAlarms Article |
| 1.3.6.1.4.1.20044.110.2.3.3.49.1 | Rowrmoac17ilwbAlmlineOscThresholdAlarmsEntry | not-accessible | current | Row definition for the rmoac17ilwbAlmlineOscThresholdAlarms table |
| 1.3.6.1.4.1.20044.110.2.3.3.49.1.1 | Columnrmoac17ilwbAlmlineOscThresholdAlarmsIndex | read-only | current | Index definition for the rmoac17ilwbAlmlineOscThresholdAlarms table |
| 1.3.6.1.4.1.20044.110.2.3.3.49.1.2 | Columnrmoac17ilwbAlmLineOscTxPwrLowAlarmPortn | read-only | current | OSC Tx Power Low Alarm :This OID indicates the Tx Power of the OSC is lower than the warning threshold<Help> This alarm indicates the Tx Power of the OSC is lo… |
| 1.3.6.1.4.1.20044.110.2.3.3.49.1.3 | Columnrmoac17ilwbAlmLineOscTxPwrHighAlarmPortn | read-only | current | OSC Tx Power High Alarm :This OID indicates the Tx Power of the OSC is higher than the warning threshold<Help> This alarm indicates the Tx Power of the OSC is … |
| 1.3.6.1.4.1.20044.110.2.3.3.49.1.4 | Columnrmoac17ilwbAlmLineOscTxBiasLowAlarmPortn | read-only | current | OSC Bias Current Low Alarm :This OID indicates the OSC bias current is lower than the alarm threshold <Help> This alarm indicates the OSC bias current is lower… |
| 1.3.6.1.4.1.20044.110.2.3.3.49.1.5 | Columnrmoac17ilwbAlmLineOscTxBiasHighAlarmPortn | read-only | current | OSC Bias Current High Alarm :This OID indicates the OSC bias current is higher than the alarm threshold <Help> This alarm indicates the OSC bias current is hig… |
| 1.3.6.1.4.1.20044.110.2.3.3.49.1.6 | Columnrmoac17ilwbAlmLineOscVccLowAlarmPortn | read-only | current | OSC Vcc Low Alarm :This OID indicates the Vcc of the OSC is lower than the warning threshold<Help> This alarm indicates the Vcc of the OSC is lower than the al… |
| 1.3.6.1.4.1.20044.110.2.3.3.49.1.7 | Columnrmoac17ilwbAlmLineOscVccHighAlarmPortn | read-only | current | OSC Vcc High Alarm :This OID indicates the Vcc of the OSC is higher than the warning threshold<Help> This alarm indicates the Vcc of the OSC is higher than the… |
| 1.3.6.1.4.1.20044.110.2.3.3.49.1.8 | Columnrmoac17ilwbAlmLineOscTempLowAlarmPortn | read-only | current | OSC Temperature Low Alarm :This OID indicates the OSC temperature is lower than the alarm threshold <Help> This alarm indicates the OSC temperature is lower th… |
| 1.3.6.1.4.1.20044.110.2.3.3.49.1.9 | Columnrmoac17ilwbAlmLineOscTempHighAlarmPortn | read-only | current | OSC Temperature High Alarm :This OID indicates the OSC temperature is higher than the alarm threshold <Help> This alarm indicates the OSC temperature is higher… |
| 1.3.6.1.4.1.20044.110.2.3.3.49.1.10 | Columnrmoac17ilwbAlmLineOscSpanlossLowAlarmPortn | read-only | current | OSC Span Loss Low Alarm :This OID indicates the OSC Span Loss is 3dB lower than the span loss reference<Help> This alarm indicates the OSC Span Loss is 3dB low… |
| 1.3.6.1.4.1.20044.110.2.3.3.49.1.11 | Columnrmoac17ilwbAlmLineOscSpanlossHighAlarmPortn | read-only | current | OSC Span Loss High Alarm :This OID indicates the OSC Span Loss is 3dB higher than the span loss reference <Help> This alarm indicates the OSC Span Loss is 3dB … |
| 1.3.6.1.4.1.20044.110.2.3.3.49.1.16 | Columnrmoac17ilwbAlmLineOscRxPwrLowAlarmPortn | read-only | current | OSC Rx Power Low Alarm :This OID indicates the Rx Power of the OSC is lower than the alarm threshold<Help> This alarm indicates the Rx Power of the OSC is lowe… |
| 1.3.6.1.4.1.20044.110.2.3.3.49.1.17 | Columnrmoac17ilwbAlmLineOscRxPwrHighAlarmPortn | read-only | current | OSC Rx Power High Alarm :This OID indicates the Rx Power of the OSC is higher than the alarm threshold<Help> This alarm indicates the Rx Power of the OSC is hi… |
| 1.3.6.1.4.1.20044.110.2.3.3.50 | Tablermoac17ilwbAlmlineOscThresholdsWarningsTable | not-accessible | current | List of rmoac17ilwbAlmlineOscThresholdsWarnings Article |
| 1.3.6.1.4.1.20044.110.2.3.3.50.1 | Rowrmoac17ilwbAlmlineOscThresholdsWarningsEntry | not-accessible | current | Row definition for the rmoac17ilwbAlmlineOscThresholdsWarnings table |
| 1.3.6.1.4.1.20044.110.2.3.3.50.1.1 | Columnrmoac17ilwbAlmlineOscThresholdsWarningsIndex | read-only | current | Index definition for the rmoac17ilwbAlmlineOscThresholdsWarnings table |
| 1.3.6.1.4.1.20044.110.2.3.3.50.1.2 | Columnrmoac17ilwbAlmLineOscTxPwrLowWarningPortn | read-only | current | OSC Tx Power Low Warning :This OID indicates the Tx Power of the OSC is lower than the warning threshold<Help> This alarm indicates the Tx Power of the OSC is … |
| 1.3.6.1.4.1.20044.110.2.3.3.50.1.3 | Columnrmoac17ilwbAlmLineOscTxPwrHighWarningPortn | read-only | current | OSC Tx Power High Warning :This OID indicates the Tx Power of the OSC is higher than the warning threshold<Help> This alarm indicates the Tx Power of the OSC i… |
| 1.3.6.1.4.1.20044.110.2.3.3.50.1.4 | Columnrmoac17ilwbAlmLineOscTxBiasLowWarningPortn | read-only | current | OSC Bias Current Low Warning :This OID indicates the OSC bias current is lower than the warning threshold <Help> This alarm indicates the OSC bias current is l… |
| 1.3.6.1.4.1.20044.110.2.3.3.50.1.5 | Columnrmoac17ilwbAlmLineOscTxBiasHighWarningPortn | read-only | current | OSC Bias Current High Warning :This OID indicates the OSC bias current is higher than the warning threshold <Help> This alarm indicates the OSC bias current is… |
| 1.3.6.1.4.1.20044.110.2.3.3.50.1.6 | Columnrmoac17ilwbAlmLineOscVccLowWarningPortn | read-only | current | OSC Vcc Low Warning :This OID indicates the Vcc of the OSC is lower than the warning threshold<Help> This alarm indicates the Vcc of the OSC is lower than the … |
| 1.3.6.1.4.1.20044.110.2.3.3.50.1.7 | Columnrmoac17ilwbAlmLineOscVccHighWarningPortn | read-only | current | OSC Vcc High Warning :This OID indicates the Vcc of the OSC is higher than the warning threshold<Help> This alarm indicates the Vcc of the OSC is higher than t… |
| 1.3.6.1.4.1.20044.110.2.3.3.50.1.8 | Columnrmoac17ilwbAlmLineOscTempLowWarningPortn | read-only | current | OSC Temperature Low Warning :This OID indicates the OSC temperature is lower than the warning threshold <Help> This alarm indicates the OSC temperature is lowe… |
| 1.3.6.1.4.1.20044.110.2.3.3.50.1.9 | Columnrmoac17ilwbAlmLineOscTempHighWarningPortn | read-only | current | OSC Temperature High Warning :This OID indicates the OSC temperature is higher than the warning threshold <Help> This alarm indicates the OSC temperature is hi… |
| 1.3.6.1.4.1.20044.110.2.3.3.50.1.10 | Columnrmoac17ilwbAlmLineOscSpanlossLowWarningPortn | read-only | current | OSC Span Loss Low Warning :This OID indicates the OSC Span Loss is 1dB lower than the span loss reference<Help> This alarm indicates the OSC Span Loss is 1dB l… |
| 1.3.6.1.4.1.20044.110.2.3.3.50.1.11 | Columnrmoac17ilwbAlmLineOscSpanlossHighWarningPortn | read-only | current | OSC Span Loss High Warning :This OID indicates the OSC Span Loss is 1dB higher than the span loss reference <Help> This alarm indicates the OSC Span Loss is 1d… |
| 1.3.6.1.4.1.20044.110.2.3.3.50.1.16 | Columnrmoac17ilwbAlmLineOscRxPwrLowWarningPortn | read-only | current | OSC Rx Power Low Warning :This OID indicates the Rx Power of the OSC is lower than the warning threshold<Help> This alarm indicates the Rx Power of the OSC is … |
| 1.3.6.1.4.1.20044.110.2.3.3.50.1.17 | Columnrmoac17ilwbAlmLineOscRxPwrHighWarningPortn | read-only | current | OSC Rx Power High Warning :This OID indicates the Rx Power of the OSC is higher than the warning threshold<Help> This alarm indicates the Rx Power of the OSC i… |
| 1.3.6.1.4.1.20044.110.3 | Nodermoac17ilwbmeasures | |||
| 1.3.6.1.4.1.20044.110.3.1 | Nodermoac17ilwbMesrOther | |||
| 1.3.6.1.4.1.20044.110.3.1.80 | Scalarrmoac17ilwbMesrtempMeas | read-only | current | Module Temperature :This OID gives the temperature of the PM (Temperature =AV_S16/256) (Unit = C) <Help> This measure gives the temperature of the module |
| 1.3.6.1.4.1.20044.110.3.1.82 | Scalarrmoac17ilwbMesrmoduleTempMin | read-only | current | Min Module Temperature :This OID gives the minimum temperature value of the Module (Temperature = AV_S16/256) (Unit = C) <Help> This Measure gives the minimum … |
| 1.3.6.1.4.1.20044.110.3.1.83 | Scalarrmoac17ilwbMesrmoduleTempMax | read-only | current | Max Module Temperature :This OID gives the maximum temperature value of the Module (Temperature = AV_S16/256) (Unit = C) <Help> This Measure gives the maximum … |
| 1.3.6.1.4.1.20044.110.3.2 | Nodermoac17ilwbMesrClient | |||
| 1.3.6.1.4.1.20044.110.3.2.32 | Scalarrmoac17ilwbMesrclientEdfaBiasMeas | read-only | current | IL2 Pump Laser Current :This OID gives the pump laser current of the IL2 Optical Module (Current =AV_U16/20) (Unit = mA) <Help> This measure gives the bias of … |
| 1.3.6.1.4.1.20044.110.3.2.33 | Scalarrmoac17ilwbMesrclientEdfaTxpwrMeas | read-only | current | IL2 Tx Power :This OID gives the transmit power value of the IL2 Optical Module (Power =(AV_U16-32768)*0.005) (Unit = dBm) <Help> This measure gives the Tx opt… |
| 1.3.6.1.4.1.20044.110.3.2.34 | Scalarrmoac17ilwbMesrclientEdfaRxpwrMeas | read-only | current | IL2 Rx Power :This OID gives the receive power value of the IL2 Optical Module (Power =(AV_U16-32768)*0.005) (Unit = dBm) <Help> This measure gives the Rx opti… |
| 1.3.6.1.4.1.20044.110.3.2.35 | Scalarrmoac17ilwbMesrclientEdfaGainMeas | read-only | current | IL2 Gain Target :This OID gives the gain value of the IL2 Module (Gain =(AV_U16-32768)*0.005) (Unit = dB) <Help> This information gives the target gain of the … |
| 1.3.6.1.4.1.20044.110.3.2.36 | Scalarrmoac17ilwbMesrclientOscSpanLoss | read-only | current | IL2 Input Span Loss :This OID indicates the attenuation of the span connected to the IL2 input (Power =(AV_U16-32768)*0.005) (Unit = dB) <Help> This measure in… |
| 1.3.6.1.4.1.20044.110.3.2.37 | Scalarrmoac17ilwbMesrclientOscSpanLossRef | read-only | current | IL2 Input Span Loss Ref :This OID indicates the referenced attenuation of the span connected to the IL2 input (Used to monitor the variation of the span loss) … |
| 1.3.6.1.4.1.20044.110.3.2.38 | Scalarrmoac17ilwbMesrclientCorrectedGain | read-only | current | IL2 Gain :This OID gives the gain value of the IL2 Module corrected by the ASE compensation mechanism (Gain =(AV_U16-32768)*0.005) (Unit = dB) <Help> This meas… |
| 1.3.6.1.4.1.20044.110.3.2.39 | Scalarrmoac17ilwbMesrclientMsaInputPower | read-only | current | IL2 MSA Rx Power :This OID indicates the input power of the Mid Stage Access of the IL2 (Power =(AV_U16-32768)*0.005) (Unit = dBm) <Help> This measure indicate… |
| 1.3.6.1.4.1.20044.110.3.2.40 | Scalarrmoac17ilwbMesrclientMsaOutputPower | read-only | current | IL2 MSA Tx Power :This OID indicates the output power of the Mid Stage Access of the IL2 (Power =(AV_U16-32768)*0.005) (Unit = dBm) <Help> This measure indicat… |
| 1.3.6.1.4.1.20044.110.3.2.41 | Scalarrmoac17ilwbMesrclientMsaAttenuation | read-only | current | IL2 MSA Attenuation :This OID indicates the attenuation applied on the Mid Stage Access of the IL2 (Attenuation =(AV_U16-32768)*0.005) (Unit = dB) <Help> This … |
| 1.3.6.1.4.1.20044.110.3.2.42 | Scalarrmoac17ilwbMesrclientMsaAttenuationRef | read-only | current | IL2 MSA Attenuation Ref :This OID indicates the reference attenuation stored for the Mid Stage Access of the In-Line1 (Used to monitor the variation of this at… |
| 1.3.6.1.4.1.20044.110.3.3 | Nodermoac17ilwbMesrLine | |||
| 1.3.6.1.4.1.20044.110.3.3.48 | Scalarrmoac17ilwbMesrlineEdfaBiasMeas | read-only | current | IL1 Pump Laser Current :This OID gives the pump laser current of the IL1 Optical Module (Current =AV_U16/20) (Unit = mA) <Help> This measure gives the bias of … |
| 1.3.6.1.4.1.20044.110.3.3.49 | Scalarrmoac17ilwbMesrlineEdfaTxpwrMeas | read-only | current | IL1 Tx Power :This OID gives the transmit power value of the IL1 Optical Module (Power =(AV_U16-32768)*0.005) (Unit = dBm) <Help> This measure gives the Tx opt… |
| 1.3.6.1.4.1.20044.110.3.3.50 | Scalarrmoac17ilwbMesrlineEdfaRxpwrMeas | read-only | current | IL1 Rx Power :This OID gives the receive power value of the IL1 Optical Module (Power =(AV_U16-32768)*0.005) (Unit = dBm) <Help> This measure gives the Rx opti… |
| 1.3.6.1.4.1.20044.110.3.3.51 | Scalarrmoac17ilwbMesrlineEdfaGainMeas | read-only | current | IL1 Gain Target :This OID gives the gain value of the IL1 Module (Gain =(AV_U16-32768)*0.005) (Unit = dB) <Help> This information gives the target gain of the … |
| 1.3.6.1.4.1.20044.110.3.3.52 | Scalarrmoac17ilwbMesrlineOscSpanLoss | read-only | current | IL1 Input Span Loss :This OID indicates the attenuation of the span connected to the IL1 input (Power =(AV_U16-32768)*0.005) (Unit = dB) <Help> This measure in… |
| 1.3.6.1.4.1.20044.110.3.3.53 | Scalarrmoac17ilwbMesrlineOscSpanLossRef | read-only | current | IL1 Input Span Loss Ref :This OID indicates the referenced attenuation of the span connected to the IL1 input (Used to monitor the variation of the span loss) … |
| 1.3.6.1.4.1.20044.110.3.3.54 | Scalarrmoac17ilwbMesrlineCorrectedGain | read-only | current | IL1 Gain :This OID gives the gain value of the IL1 Module corrected by the ASE compensation mechanism (Gain =(AV_U16-32768)*0.005) (Unit = dB) <Help> This meas… |
| 1.3.6.1.4.1.20044.110.3.3.55 | Scalarrmoac17ilwbMesrlineMsaInputPower | read-only | current | IL1 MSA Rx Power :This OID indicates the input power of the Mid Stage Access of the IL1 (Power =(AV_U16-32768)*0.005) (Unit = dBm) <Help> This measure indicate… |
| 1.3.6.1.4.1.20044.110.3.3.56 | Scalarrmoac17ilwbMesrlineMsaOutputPower | read-only | current | IL1 MSA Tx Power :This OID indicates the output power of the Mid Stage Access of the IL1 (Power =(AV_U16-32768)*0.005) (Unit = dBm) <Help> This measure indicat… |
| 1.3.6.1.4.1.20044.110.3.3.57 | Scalarrmoac17ilwbMesrlineMsaAttenuation | read-only | current | IL1 MSA Attenuation :This OID indicates the attenuation applied on the Mid Stage Access of the IL1 (Attenuation =(AV_U16-32768)*0.005) (Unit = dB) <Help> This … |
| 1.3.6.1.4.1.20044.110.3.3.58 | Scalarrmoac17ilwbMesrlineMsaAttenuationRef | read-only | current | IL1 MSA Attenuation Ref :This OID indicates the reference attenuation stored for the Mid Stage Access of the IL1 (Used to monitor the variation of this attenua… |
| 1.3.6.1.4.1.20044.110.3.3.64 | Tablermoac17ilwbMesrlineOscTxPowerTable | not-accessible | current | List of rmoac17ilwbMesrlineOscTxPower Article |
| 1.3.6.1.4.1.20044.110.3.3.64.1 | Rowrmoac17ilwbMesrlineOscTxPowerEntry | not-accessible | current | Row definition for the rmoac17ilwbMesrlineOscTxPower table |
| 1.3.6.1.4.1.20044.110.3.3.64.1.1 | Columnrmoac17ilwbMesrlineOscTxPowerIndex | read-only | current | Index definition for the rmoac17ilwbMesrlineOscTxPower table |
| 1.3.6.1.4.1.20044.110.3.3.64.1.2 | Columnrmoac17ilwbMesrlineOscTxPowerPortn | read-only | current | OSC Tx Power :This OID gives the transmit power value of the Transceiver, read from the DDM (Digital Diagnostic Monitoring) (Power = 10*log(AV_U16)-40) (Unit =… |
| 1.3.6.1.4.1.20044.110.3.3.65 | Tablermoac17ilwbMesrlineOscRxPowerTable | not-accessible | current | List of rmoac17ilwbMesrlineOscRxPower Article |
| 1.3.6.1.4.1.20044.110.3.3.65.1 | Rowrmoac17ilwbMesrlineOscRxPowerEntry | not-accessible | current | Row definition for the rmoac17ilwbMesrlineOscRxPower table |
| 1.3.6.1.4.1.20044.110.3.3.65.1.1 | Columnrmoac17ilwbMesrlineOscRxPowerIndex | read-only | current | Index definition for the rmoac17ilwbMesrlineOscRxPower table |
| 1.3.6.1.4.1.20044.110.3.3.65.1.2 | Columnrmoac17ilwbMesrlineOscRxPowerPortn | read-only | current | OSC Rx Power :This OID gives the receive power value of the Transceiver, read in the DDM (Digital Diagnostic Monitoring) (Power = 10*log(AV_U16)-40) (Unit = dB… |
| 1.3.6.1.4.1.20044.110.3.3.66 | Tablermoac17ilwbMesrlineOscBiasTable | not-accessible | current | List of rmoac17ilwbMesrlineOscBias Article |
| 1.3.6.1.4.1.20044.110.3.3.66.1 | Rowrmoac17ilwbMesrlineOscBiasEntry | not-accessible | current | Row definition for the rmoac17ilwbMesrlineOscBias table |
| 1.3.6.1.4.1.20044.110.3.3.66.1.1 | Columnrmoac17ilwbMesrlineOscBiasIndex | read-only | current | Index definition for the rmoac17ilwbMesrlineOscBias table |
| 1.3.6.1.4.1.20044.110.3.3.66.1.2 | Columnrmoac17ilwbMesrlineOscBiasPortn | read-only | current | OSC Bias :This OID gives the Laser bias value of the Transceiver, read from the DDM (Digital Diagnostic Monitoring) (Bias = AV_U16/500) (Unit = mA) <Help> This… |
| 1.3.6.1.4.1.20044.110.3.3.67 | Tablermoac17ilwbMesrlineOscTempTable | not-accessible | current | List of rmoac17ilwbMesrlineOscTemp Article |
| 1.3.6.1.4.1.20044.110.3.3.67.1 | Rowrmoac17ilwbMesrlineOscTempEntry | not-accessible | current | Row definition for the rmoac17ilwbMesrlineOscTemp table |
| 1.3.6.1.4.1.20044.110.3.3.67.1.1 | Columnrmoac17ilwbMesrlineOscTempIndex | read-only | current | Index definition for the rmoac17ilwbMesrlineOscTemp table |
| 1.3.6.1.4.1.20044.110.3.3.67.1.2 | Columnrmoac17ilwbMesrlineOscTempPortn | read-only | current | OSC Temperature :This OID gives the Laser temperature value of the Transceiver, read from the DDM (Digital Diagnostic Monitoring) (Temperature = AV_S16/256) (U… |
| 1.3.6.1.4.1.20044.110.3.3.68 | Tablermoac17ilwbMesrlineOscVoltTable | not-accessible | current | List of rmoac17ilwbMesrlineOscVolt Article |
| 1.3.6.1.4.1.20044.110.3.3.68.1 | Rowrmoac17ilwbMesrlineOscVoltEntry | not-accessible | current | Row definition for the rmoac17ilwbMesrlineOscVolt table |
| 1.3.6.1.4.1.20044.110.3.3.68.1.1 | Columnrmoac17ilwbMesrlineOscVoltIndex | read-only | current | Index definition for the rmoac17ilwbMesrlineOscVolt table |
| 1.3.6.1.4.1.20044.110.3.3.68.1.2 | Columnrmoac17ilwbMesrlineOscVoltPortn | read-only | current | OSC Voltage :This OID gives the Voltage value of the Transceiver, read from the DDM (Digital Diagnostic Monitoring) (Voltage = AV_U16/10000) (Unit = V) <Help> … |
| 1.3.6.1.4.1.20044.110.6 | Nodermoac17ilwbcontrolsWrite | |||
| 1.3.6.1.4.1.20044.110.6.1 | Nodermoac17ilwbCtrlOther | |||
| 1.3.6.1.4.1.20044.110.6.1.0 | Nodermoac17ilwbCtrlsynth0 | |||
| 1.3.6.1.4.1.20044.110.6.1.0.1 | Scalarrmoac17ilwbCtrlConfLoad | read-write | current | Load Configuration Tables :When set this enables loading from flash configuration1 into the module. |
| 1.3.6.1.4.1.20044.110.6.1.0.9 | Scalarrmoac17ilwbCtrlConfFlash | read-write | current | Write Configuration Tables :This bit saves the current configuration of the module as configuration in the flash. <Help> This control saves the customer config… |
| 1.3.6.1.4.1.20044.110.6.1.0.13 | Scalarrmoac17ilwbCtrlConfClear | read-write | current | Clear Configuration Tables :This bit clears the configuration tables from configuration in the flash. <Help> This control restores the default configuration of… |
| 1.3.6.1.4.1.20044.110.6.1.5 | Nodermoac17ilwbCtrlswMgnt | |||
| 1.3.6.1.4.1.20044.110.6.1.5.2 | Scalarrmoac17ilwbCtrlColdReset | read-write | current | PM Cold Reset :This OID, when set, causes a cold reset of the Software. This reset is traffic affecting, and the configuration of Software is reloaded on start… |
| 1.3.6.1.4.1.20044.110.6.1.5.3 | Scalarrmoac17ilwbCtrlWarmReset | read-write | current | PM Warm Reset :This OID, when set, causes a warm reset of the Software. This reset is not traffic affecting, and the configuration of the Sofwtare remains unch… |
| 1.3.6.1.4.1.20044.110.6.1.6 | Nodermoac17ilwbCtrlsynth6 | |||
| 1.3.6.1.4.1.20044.110.6.1.6.1 | Scalarrmoac17ilwbCtrlCurrentGwReset | read-write | current | Active Gateware Reset :This OID, when set, resets the active gateware. It is traffic affecting. |
| 1.3.6.1.4.1.20044.110.6.1.73 | Nodermoac17ilwbCtrlledTest | |||
| 1.3.6.1.4.1.20044.110.6.1.73.1 | Scalarrmoac17ilwbCtrlGreenLed | read-write | current | Green Leds Test :This OID switches on all the green Leds as a test feature. <Help> This control initiates a test leds turning all the LEDs to green |
| 1.3.6.1.4.1.20044.110.6.1.73.2 | Scalarrmoac17ilwbCtrlRedLed | read-write | current | Red Leds Test :This OID switches on all the red Leds as a test feature. <Help> This control initiates a test leds turning all the LEDs to red |
| 1.3.6.1.4.1.20044.110.6.1.73.3 | Scalarrmoac17ilwbCtrlLedOff | read-write | current | Leds Off :This OID switches off all the Leds as a test feature. <Help> This control initiates a test leds turning all the LEDs to OFF |
| 1.3.6.1.4.1.20044.110.6.1.75 | Nodermoac17ilwbCtrlmaintMode | |||
| 1.3.6.1.4.1.20044.110.6.1.75.1 | Scalarrmoac17ilwbCtrlMaintenance | read-write | current | PM Maintenance Mode :This OID sets the PM in maintenance mode <Help> This control enables the maintenance mode of the module |
| 1.3.6.1.4.1.20044.110.6.1.76 | Nodermoac17ilwbCtrlaprRestart | |||
| 1.3.6.1.4.1.20044.110.6.1.76.1 | Scalarrmoac17ilwbCtrlAprManualRestart | read-write | current | APR Manual Restart :This OID initiates the Restart mechanism to retrieve from the APR state.<Help> This control initiates the Restart mechanism to retrieve fro… |
| 1.3.6.1.4.1.20044.110.6.2 | Nodermoac17ilwbCtrlClient | |||
| 1.3.6.1.4.1.20044.110.6.2.33 | Nodermoac17ilwbCtrlclientOscInputSpanLoss | |||
| 1.3.6.1.4.1.20044.110.6.2.33.1 | Scalarrmoac17ilwbCtrlClientSpanLoss | read-write | current | Store IL2 Input Span Loss :This OID stores the current input span Loss as a reference to monitor the span loss variation <Help> This parameter stores the curre… |
| 1.3.6.1.4.1.20044.110.6.2.34 | Scalarrmoac17ilwbCtrlclientGainCstMonitorValue | read-write | current | IL2 Fiber Aging Period :This OID sets the value of the monitoring period to detect a fiber aging. (Unit = s) This value sets the monitoring period to detect a … |
| 1.3.6.1.4.1.20044.110.6.2.36 | Scalarrmoac17ilwbCtrlclientGainSettingValue | read-write | current | IL2 Gain Target :This OID sets the value of the nominal gain of the IL2lifier Module (active only in constant output power mode) (AV=(Gain/0,005) + 32768) (Uni… |
| 1.3.6.1.4.1.20044.110.6.2.37 | Nodermoac17ilwbCtrlclientGainProcessing | |||
| 1.3.6.1.4.1.20044.110.6.2.37.1 | Scalarrmoac17ilwbCtrlClientGainProc | read-write | current | IL2 Fiber Aging Compensation :This OID initiates the automatic nominal gain adjustment on the IL2lifier Module<Help> This control initiates the automatic nomin… |
| 1.3.6.1.4.1.20044.110.6.2.38 | Scalarrmoac17ilwbCtrlclientGainCstFiberAgingMarginValue | read-write | current | IL2 Aging Threshold :This OID sets the threshold to consider the power drop as a fiber aging. (active only in constant gain mode) (AV=(Gain/0,005) + 32768) (Un… |
| 1.3.6.1.4.1.20044.110.6.2.40 | Nodermoac17ilwbCtrlclientMsaAttenuationValue | |||
| 1.3.6.1.4.1.20044.110.6.2.40.1 | Scalarrmoac17ilwbCtrlClientAttenuation | read-write | current | Store IL2 MSA Attenuation :This OID stores the current attenuation applied on the Mid Stage Access of the IL2 (used for monitoring the MSA attenuation variatio… |
| 1.3.6.1.4.1.20044.110.6.2.41 | Scalarrmoac17ilwbCtrlclientTlvPreviousAmpPwrW | read-write | current | Previous Amplifier Output Power :This OID sets the value of the previous Amplifier output power to be used to compute the local span loss monitoring (AV=(Gain/… |
| 1.3.6.1.4.1.20044.110.6.2.42 | Scalarrmoac17ilwbCtrlclientTlvPreviousRoadmLambdaNbW | read-write | current | Previous Roadm Lambda Number :This OID sets the value of the previous Roadm wavelength number to be computed locally (Unit = Lambdas) <Help> This parameter sto… |
| 1.3.6.1.4.1.20044.110.6.2.57 | Scalarrmoac17ilwbCtrllineTlvPreviousAmpPwrW | read-write | current | Previous Amplifier Output Power :This OID sets the value of the previous Amplifier output power to be used to compute the local span loss monitoring (AV=(Gain/… |
| 1.3.6.1.4.1.20044.110.6.2.58 | Scalarrmoac17ilwbCtrllineTlvPreviousRoadmLambdaNbW | read-write | current | Previous Roadm Lambda Number :This OID sets the value of the previous Roadm wavelength number to be computed locally (Unit = Lambdas) <Help> This parameter sto… |
| 1.3.6.1.4.1.20044.110.6.3 | Nodermoac17ilwbCtrlLine | |||
| 1.3.6.1.4.1.20044.110.6.3.49 | Nodermoac17ilwbCtrllineOscInputSpanLoss | |||
| 1.3.6.1.4.1.20044.110.6.3.49.1 | Scalarrmoac17ilwbCtrlLineSpanLoss | read-write | current | Store IL1 Input Span Loss :This OID stores the current input span Loss as a reference to monitor the span loss variation<Help> This parameter stores the curren… |
| 1.3.6.1.4.1.20044.110.6.3.50 | Scalarrmoac17ilwbCtrllineGainCstMonitorValue | read-write | current | IL1 Fiber Aging Period :This OID sets the value of the monitoring period to detect a fiber aging. (Unit = s) This value sets the monitoring period to detect a … |
| 1.3.6.1.4.1.20044.110.6.3.52 | Scalarrmoac17ilwbCtrllineGainSettingValue | read-write | current | IL1 Gain Target :This OID sets the value of the nominal gain of the IL1 Module (active only in constant output power mode) (AV=(Gain/0,005) + 32768) (Unit = dB… |
| 1.3.6.1.4.1.20044.110.6.3.53 | Nodermoac17ilwbCtrllineGainProcessing | |||
| 1.3.6.1.4.1.20044.110.6.3.53.1 | Scalarrmoac17ilwbCtrlLineGainProc | read-write | current | IL1 Fiber Aging Compensation :This OID initiates the automatic nominal gain adjustment on the IL1 Module<Help> This control initiates the automatic nominal gai… |
| 1.3.6.1.4.1.20044.110.6.3.54 | Scalarrmoac17ilwbCtrllineGainCstFiberAgingMarginValue | read-write | current | IL1 Aging Threshold :This OID sets the threshold to consider the power drop as a fiber aging. (active only in constant gain mode) (AV=(Gain/0,005) + 32768) (Un… |
| 1.3.6.1.4.1.20044.110.6.3.56 | Nodermoac17ilwbCtrllineMsaAttenuationValue | |||
| 1.3.6.1.4.1.20044.110.6.3.56.1 | Scalarrmoac17ilwbCtrlLineAttenuation | read-write | current | Store IL1 MSA Attenuation :This OID stores the current attenuation applied on the Mid Stage Access of the IL1 (used for monitoring the MSA attenuation variatio… |
| 1.3.6.1.4.1.20044.110.7 | Nodermoac17ilwbri | |||
| 1.3.6.1.4.1.20044.110.7.2 | Scalarrmoac17ilwbRinvReloadInventory | read-write | current | Reload the inventory: This OID triggers an inventory reload. |
| 1.3.6.1.4.1.20044.110.7.3 | Scalarrmoac17ilwbRinvHwPlatform | read-only | current | HW platform description: This OID contains the description of the Hardware platform. |
| 1.3.6.1.4.1.20044.110.7.4 | Scalarrmoac17ilwbRinvModulePlatform | read-only | current | Module platform description: This OID contains the description of the Module. |
| 1.3.6.1.4.1.20044.110.7.5 | Scalarrmoac17ilwbRinvSwPlatform | read-only | current | SW platform description: This OID contains the description of the Software platform. |
| 1.3.6.1.4.1.20044.110.7.6 | Scalarrmoac17ilwbRinvGwPlatform | read-only | current | GW platform description: This OID contains the description of the gateware platform. |
| 1.3.6.1.4.1.20044.110.7.7 | Tablermoac17ilwbRinvBoosterTable | not-accessible | current | List of the Boosters on the selected module |
| 1.3.6.1.4.1.20044.110.7.7.1 | Rowrmoac17ilwbRinvBoosterEntry | not-accessible | current | Row definition for the Boosters table |
| 1.3.6.1.4.1.20044.110.7.7.1.1 | Columnrmoac17ilwbRinvBoosterIndex | read-only | current | Index for Booster table |
| 1.3.6.1.4.1.20044.110.7.7.1.2 | Columnrmoac17ilwbRinvBooster | read-only | current | Inventory for the Booster: This OID contains the inventory for the Booster |
| 1.3.6.1.4.1.20044.110.7.8 | Tablermoac17ilwbRinvPreAmpTable | not-accessible | current | List of the PreAmps on the selected module |
| 1.3.6.1.4.1.20044.110.7.8.1 | Rowrmoac17ilwbRinvPreAmpEntry | not-accessible | current | Row definition for the PreAmp table |
| 1.3.6.1.4.1.20044.110.7.8.1.1 | Columnrmoac17ilwbRinvPreAmpIndex | read-only | current | Index for PreAmp table |
| 1.3.6.1.4.1.20044.110.7.8.1.2 | Columnrmoac17ilwbRinvPreAmp | read-only | current | Inventory for the PreAmp: This OID contains the inventory for the PreAmp |
| 1.3.6.1.4.1.20044.110.9 | Nodermoac17ilwbConfig | |||
| 1.3.6.1.4.1.20044.110.9.1 | Nodermoac17ilwbCfgNoValue | |||
| 1.3.6.1.4.1.20044.110.9.1.1 | Nodermoac17ilwbtableclientStartup | |||
| 1.3.6.1.4.1.20044.110.9.1.1.2 | Scalarrmoac17ilwbCfgclientEdfaLaserCtrl | read-write | current | Default Settings on Client Laser :This OID configures the default initialisation settings on the client laser. |
| 1.3.6.1.4.1.20044.110.9.1.1.3 | Scalarrmoac17ilwbCfgclientEdfaLaserMode | read-write | current | Default Settings on Client mode :This OID configures the default mode on the client amplifier. |
| 1.3.6.1.4.1.20044.110.9.1.1.4 | Scalarrmoac17ilwbCfgclientGainValue | read-write | current | Default Settings on Client Gain :This OID configures the default gain on the client amplifier. |
| 1.3.6.1.4.1.20044.110.9.1.1.5 | Scalarrmoac17ilwbCfgclientTiltValue | read-write | current | Default Settings on Client Tilt :This OID configures the default tilt on the client amplifier. |
| 1.3.6.1.4.1.20044.110.9.1.1.6 | Scalarrmoac17ilwbCfgclientMsaLoss | read-write | current | Default Settings on Client MSA :This OID configures the default MSA value on the client amplifier. |
| 1.3.6.1.4.1.20044.110.9.1.1.7 | Scalarrmoac17ilwbCfgclientOutputPowerValue | read-write | current | Default Settings on Client Output power :This OID configures the default Output power value on the client amplifier. |
| 1.3.6.1.4.1.20044.110.9.1.1.8 | Scalarrmoac17ilwbCfgclientAseCompensation | read-write | current | Default Settings on Client ASE :This OID configures the default ASE compensation value on the client amplifier. |
| 1.3.6.1.4.1.20044.110.9.1.1.10 | Scalarrmoac17ilwbCfgclientGainHighAlarm | read-write | current | Default setting on Gain High Alarm :This register configures the default initialisation settings on the alarm threshold |
| 1.3.6.1.4.1.20044.110.9.1.1.11 | Scalarrmoac17ilwbCfgclientGainHighWarning | read-write | current | Default setting on Gain High Warning :This register configures the default initialisation settings on the warning threshold |
| 1.3.6.1.4.1.20044.110.9.1.1.12 | Scalarrmoac17ilwbCfgclientGainLowWarning | read-write | current | Default setting on Gain Low Warning :This register configures the default initialisation settings on the warning threshold |
| 1.3.6.1.4.1.20044.110.9.1.1.13 | Scalarrmoac17ilwbCfgclientGainLowAlarm | read-write | current | Default setting on Gain Low Alarm :This register configures the default initialisation settings on the alarm threshold |
| 1.3.6.1.4.1.20044.110.9.1.1.14 | Scalarrmoac17ilwbCfgclientLossOfSignal | read-write | current | Default setting on Loss Of Signal :This register configures the default initialisation settings on the Loss Of Signal threshold |
| 1.3.6.1.4.1.20044.110.9.2 | Nodermoac17ilwbCfgLineStartUp | |||
| 1.3.6.1.4.1.20044.110.9.2.1 | Nodermoac17ilwbtablelineStartup | |||
| 1.3.6.1.4.1.20044.110.9.2.1.2 | Scalarrmoac17ilwbCfglineEdfaLaserCtrl | read-write | current | Default Settings on Line Laser :This OID configures the default initialisation settings on the line laser. |
| 1.3.6.1.4.1.20044.110.9.2.1.3 | Scalarrmoac17ilwbCfglineEdfaLaserMode | read-write | current | Default Settings on Line mode :This OID configures the default mode on the line amplifier. |
| 1.3.6.1.4.1.20044.110.9.2.1.4 | Scalarrmoac17ilwbCfglineGainValue | read-write | current | Default Settings on Line Gain :This OID configures the default gain on the line amplifier. |
| 1.3.6.1.4.1.20044.110.9.2.1.5 | Scalarrmoac17ilwbCfglineTiltValue | read-write | current | Default Settings on Line Tilt :This OID configures the default tilt on the line amplifier. |
| 1.3.6.1.4.1.20044.110.9.2.1.6 | Scalarrmoac17ilwbCfglineMsaLoss | read-write | current | Default Settings on Line MSA :This OID configures the default MSA value on the line amplifier. |
| 1.3.6.1.4.1.20044.110.9.2.1.7 | Scalarrmoac17ilwbCfglineOutputPowerValue | read-write | current | Default Settings on Line Output power :This OID configures the default Output power value on the line amplifier. |
| 1.3.6.1.4.1.20044.110.9.2.1.8 | Scalarrmoac17ilwbCfglineAseCompensation | read-write | current | Default Settings on Line ASE :This OID configures the default ASE compensation value on the line amplifier. |
| 1.3.6.1.4.1.20044.110.9.2.1.10 | Scalarrmoac17ilwbCfglineGainHighAlarm | read-write | current | Default setting on Gain High Alarm :This register configures the default initialisation settings on the alarm threshold |
| 1.3.6.1.4.1.20044.110.9.2.1.11 | Scalarrmoac17ilwbCfglineGainHighWarning | read-write | current | Default setting on Gain High Warning :This register configures the default initialisation settings on the warning threshold |
| 1.3.6.1.4.1.20044.110.9.2.1.12 | Scalarrmoac17ilwbCfglineGainLowWarning | read-write | current | Default setting on Gain Low Warning :This register configures the default initialisation settings on the warning threshold |
| 1.3.6.1.4.1.20044.110.9.2.1.13 | Scalarrmoac17ilwbCfglineGainLowAlarm | read-write | current | Default setting on Gain Low Alarm :This register configures the default initialisation settings on the alarm threshold |
| 1.3.6.1.4.1.20044.110.9.2.1.14 | Scalarrmoac17ilwbCfglineLossOfSignal | read-write | current | Default setting on Loss Of Signal :This register configures the default initialisation settings on the Loss Of Signal threshold |
| 1.3.6.1.4.1.20044.110.9.2.1.18 | Scalarrmoac17ilwbCfglossEnable | read-write | current | Default setting on Loss Of Signal :This register configures the default initialisation settings on the Loss Of Signal |
| 1.3.6.1.4.1.20044.110.9.3 | Nodermoac17ilwbCfgClientSupvStartUp | |||
| 1.3.6.1.4.1.20044.110.9.3.1 | Tablermoac17ilwbCfgLineStartupTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.110.9.3.1.1 | Rowrmoac17ilwbCfgLineStartupEntry | not-accessible | current | Row definition for the clientSupvStartUp table |
| 1.3.6.1.4.1.20044.110.9.3.1.1.1 | Columnrmoac17ilwbCfgLineStartupIndex | read-only | current | Index definition for the lineStartup table |
| 1.3.6.1.4.1.20044.110.9.3.1.1.3 | Columnrmoac17ilwbCfgLineOscLaserCtrlPortn | read-write | current | Default Settings on OSC Laser :This OID configures the default initialisation settings on the OSC |
| 1.3.6.1.4.1.20044.110.9.3.1.1.4 | Columnrmoac17ilwbCfgLineOscOosPortn | read-write | current | Default Settings on OSC mode :This OID configures the default mode on the OSC |
| 1.3.6.1.4.1.20044.110.9.3.1.1.5 | Columnrmoac17ilwbCfgLineOscSpanLengthPortn | read-write | current | Default Settings on OSC span length :This OID defines the length of the span connected on the OSC port |
| 1.3.6.1.4.1.20044.110.9.3.1.1.6 | Columnrmoac17ilwbCfgLineOscCorrectionFactorPortn | read-write | current | Default Settings on OSC attenuation corrector factor :This OID defines the correction factor to apply on the span attenuation measure on the OSC Channel (1510)… |
| 1.3.6.1.4.1.20044.110.9.3.1.1.11 | Columnrmoac17ilwbCfgLineSpanLossHighAlarmPortn | read-write | current | Default setting on Span Loss High Alarm :This register configures the default initialisation settings on the alarm threshold |
| 1.3.6.1.4.1.20044.110.9.3.1.1.12 | Columnrmoac17ilwbCfgLineSpanLossHighWarningPortn | read-write | current | Default setting on Span Loss High Warning :This register configures the default initialisation settings on the warning threshold |
| 1.3.6.1.4.1.20044.110.9.3.1.1.13 | Columnrmoac17ilwbCfgLineSpanLossLowWarningPortn | read-write | current | Default setting on Span Loss Low Warning :This register configures the default initialisation settings on the warning threshold |
| 1.3.6.1.4.1.20044.110.9.3.1.1.14 | Columnrmoac17ilwbCfgLineSpanLossLowAlarmPortn | read-write | current | Default setting on Span Loss Low Alarm :This register configures the default initialisation settings on the alarm threshold |
| 1.3.6.1.4.1.20044.110.9.4 | Nodermoac17ilwbCfgLabels | |||
| 1.3.6.1.4.1.20044.110.9.4.1 | Tablermoac17ilwbCfgLabelclientTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.110.9.4.1.1 | Rowrmoac17ilwbCfgLabelclientEntry | not-accessible | current | Row definition for the labels table |
| 1.3.6.1.4.1.20044.110.9.4.1.1.1 | Columnrmoac17ilwbCfgLabelclientIndex | read-only | current | Index definition for the labelclient table |
| 1.3.6.1.4.1.20044.110.9.4.1.1.3 | Columnrmoac17ilwbCfgLabelclientPortn | read-write | current | Default settings on the label of the Ports :These registers configures the default initialisation settings of the labels of the ports. |
| 1.3.6.1.4.1.20044.110.9.4.2 | Tablermoac17ilwbCfgLabellineTable | not-accessible | current | List of Article |
| 1.3.6.1.4.1.20044.110.9.4.2.1 | Rowrmoac17ilwbCfgLabellineEntry | not-accessible | current | Row definition for the labels table |
| 1.3.6.1.4.1.20044.110.9.4.2.1.1 | Columnrmoac17ilwbCfgLabellineIndex | read-only | current | Index definition for the labelline table |
| 1.3.6.1.4.1.20044.110.9.4.2.1.3 | Columnrmoac17ilwbCfgLabellinePortn | read-write | current | Default settings on the label of the lines :These registers configures the default initialisation settings of the labels of the lines. |
| 1.3.6.1.4.1.20044.110.9.257 | Scalarrmoac17ilwbCfgWriteConfiguration | read-write | current | Write configuration to module:This OID writes the complete configuration to the module |
| 1.3.6.1.4.1.20044.110.10 | Nodermoac17ilwbtraps | |||
| 1.3.6.1.4.1.20044.110.10.4 | Scalarrmoac17ilwbtrapBoardNumber | read-only | current | Last module which generates a trap |
| 1.3.6.1.4.1.20044.110.10.34 | Notificationrmoac17ilwbLineTrapCritGoesOn | current | Critical Line default is activated | |
| 1.3.6.1.4.1.20044.110.10.35 | Notificationrmoac17ilwbLineTrapCritGoesOff | current | Critical Line default disappeared | |
| 1.3.6.1.4.1.20044.110.10.44 | Notificationrmoac17ilwbClientTrapCritGoesOn | current | Critical client default is activated | |
| 1.3.6.1.4.1.20044.110.10.45 | Notificationrmoac17ilwbClientTrapCritGoesOff | current | Critical client default disappeared | |
| 1.3.6.1.4.1.20044.110.10.50 | Notificationrmoac17ilwbPowerTrapUrgentGoesOn | current | Urgent power supply default is activated | |
| 1.3.6.1.4.1.20044.110.10.51 | Notificationrmoac17ilwbPowerTrapUrgentGoesOff | current | Urgent power supply default disappeared |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| Rmoac17ilwbaprMode | INTEGER { rmoac17ilwbaproffmode(0), rmoac17ilwbaprsemiautomode(1), rmoac17ilwbaprautomode(2) rmoac17ilwbaprlossforwardingmode(3) rmoac17ilwbaprrepeatmode(4) } | current | Different modes on APR |
| Rmoac17ilwbBoosterCstGainAdjMode | INTEGER { rmoac17ilwbboostercstgainadjsemiautomode(1), rmoac17ilwbboostercstgainadjautomode(2) } | current | Different modes when constant Gain |
| Rmoac17ilwbBoosterGainAdjMode | INTEGER { rmoac17ilwbboostergainadjmanualmode(0), rmoac17ilwbboostergainadjsemiautomode(1), rmoac17ilwbboostergainadjautomode(2) } | current | Different modes on Gain |
| Rmoac17ilwbboosterMode | INTEGER { rmoac17ilwbboosterdefaultmode(0), rmoac17ilwbboosterconstantcurrentmode(1), rmoac17ilwbboosterconstantpowermode(2) rmoac17ilwbboosterconstantgainmode(3) rmoac17ilwbboosterpoutpinmode(4) rmoac17ilwbboostermanualmode(5) rmoac17ilwbboosterfeedforwardmode(6) rmoac17ilwbboostertransientsupmode(7) } | current | Different modes on OA booster |
| Rmoac17ilwbPreAmpCstGainAdjMode | INTEGER { rmoac17ilwbpreampcstgainadjsemiautomode(1), rmoac17ilwbpreampcstgainadjautomode(2) } | current | Different modes when constant Gain |
| Rmoac17ilwbPreAmpGainAdjMode | INTEGER { rmoac17ilwbpreampgainadjmanualmode(0), rmoac17ilwbpreampgainadjsemiautomode(1), rmoac17ilwbpreampgainadjautomode(2) } | current | Different modes on Gain |
| Rmoac17ilwbpreampMode | INTEGER { rmoac17ilwbpreampdefaultmode(0), rmoac17ilwbpreampconstantcurrentmode(1), rmoac17ilwbpreampconstantpowermode(2) rmoac17ilwbpreampconstantgainmode(3) rmoac17ilwbpreamppoutpinmode(4) rmoac17ilwbpreampmanualmode(5) rmoac17ilwbpreampfeedforwardmode(6) rmoac17ilwbpreamptransientsupmode(7) } | current | Different modes on OA preamp |