ELECTROLINE-DHT-STATUS-MIB
36 objects
No module-level DESCRIPTION found.
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5802.1.3.1.2.3.1 | TabledhtTrapAcknowledgeStatusTable | read-write | current | This table has one entry per EMS that supports trap assurance, either for start traps or for alarm traps or both. The value of cfgHmsEmsAddressAlarmTrapAssuran… |
| 1.3.6.1.4.1.5802.1.3.1.2.3.1.1 | RowdhtTrapAcknowledgeStatusEntry | not-accessible | current | This is a table entry for acknowledging an HMS cold or warm start trap, or an alarm trap. |
| 1.3.6.1.4.1.5802.1.3.1.2.3.1.1.1 | ColumndhtTrapAckAddressIndex | read-only | current | The index of the EMS address table is used as index of the trap acknowledgement table. |
| 1.3.6.1.4.1.5802.1.3.1.2.3.1.1.2 | ColumndhtTrapAckValue | read-write | current | Current value of the trap acknowledgement. Indicates the number of alarms sent since the DHT was started or reset. To acknowledge receipt of trap(s), the EMS w… |
| 1.3.6.1.4.1.5802.1.3.1.2.3.2 | ScalardhtNetworkAddress | read-only | deprecated | This is the RF IP address assigned by the DHCP. This object is deprecated and is replaced by dhtInetNetworkAddress. |
| 1.3.6.1.4.1.5802.1.3.1.2.3.3 | NodedhtHmsStatus | |||
| 1.3.6.1.4.1.5802.1.3.1.2.3.3.1 | NodedhtHmsTibStatusInfo | |||
| 1.3.6.1.4.1.5802.1.3.1.2.3.3.1.1 | NodedhtHmsTibLineStatus | |||
| 1.3.6.1.4.1.5802.1.3.1.2.3.3.1.1.1 | ScalardhtHmsTibLineRxBytes | read-only | current | Counts the number of bytes received on the RS-485 line. |
| 1.3.6.1.4.1.5802.1.3.1.2.3.3.1.1.2 | ScalardhtHmsTibLineTxBytes | read-only | current | Counts the number of bytes sent on the RS-485 line. |
| 1.3.6.1.4.1.5802.1.3.1.2.3.3.1.1.3 | ScalardhtHmsTibLineTxFifoError | read-only | current | Counts the number of errors that occurred on the Transmit(tx) FIFO. |
| 1.3.6.1.4.1.5802.1.3.1.2.3.3.1.1.4 | ScalardhtHmsTibLineRxFifoError | read-only | current | Counts the number of errors that occurred on the Receive(Rx) FIFO. |
| 1.3.6.1.4.1.5802.1.3.1.2.3.3.1.1.5 | ScalardhtHmsTibLineRxLineError | read-only | current | Counts the number of errors that occurred on the Receive (Rx) line. |
| 1.3.6.1.4.1.5802.1.3.1.2.3.4 | ScalardhtMonitoringNetworkAddress | read-only | deprecated | This is the RF IP address assigned by the DHCP to the monitoring interface in DualIp mode. This object is deprecated and is replaced by dhtInetMonitoringNetwor… |
| 1.3.6.1.4.1.5802.1.3.1.2.3.5 | ScalardhtInternalTemperature | read-only | deprecated | Measured temperature inside the NE's case/housing. Units degrees Celsius. Deprecated. Has been move into electrolineCommon branch |
| 1.3.6.1.4.1.5802.1.3.1.2.3.6 | NodedhtDlmStatus | |||
| 1.3.6.1.4.1.5802.1.3.1.2.3.6.1 | ScalardlmAcInputVoltage | read-only | current | Scaled representation of input 'line' Voltage. |
| 1.3.6.1.4.1.5802.1.3.1.2.3.6.2 | ScalardlmDhtInputVoltage | read-only | current | Scaled representation of the DHT DC input voltage |
| 1.3.6.1.4.1.5802.1.3.1.2.3.6.3 | ScalardlmRxPowerLevel | read-only | current | The received power level at the DLM input. It's the modem RX power level added to the RF attenuator pad value. |
| 1.3.6.1.4.1.5802.1.3.1.2.3.6.4 | ScalardlmTxPowerLevel | read-only | current | The transmit power level at the DLM output. It's the modem TX power level minus the RF attenuator pad value. |
| 1.3.6.1.4.1.5802.1.3.1.2.3.6.5 | ScalardlmRxAttenuatorPad | read-only | current | The Rx Attenuator pad value. If value is -2,0 the pad sens technology is not connected. Check the wiring inside the DLM If value is -1,0 there is no pad connec… |
| 1.3.6.1.4.1.5802.1.3.1.2.3.6.6 | ScalardlmTxAttenuatorPad | read-only | current | The Tx Attenuator pad value. If value is -2,0 the pad sens technology is not connected. Check the wiring inside the DLM If value is -1,0 there is no pad connec… |
| 1.3.6.1.4.1.5802.1.3.1.2.3.7 | NodefiberNodeStatus | |||
| 1.3.6.1.4.1.5802.1.3.1.2.3.7.1 | TabledhtFnOpticalReceiverTable | not-accessible | mandatory | A table containing information about optical receiver in a fiber node. |
| 1.3.6.1.4.1.5802.1.3.1.2.3.7.1.1 | RowdhtFnOpticalReceiverEntry | not-accessible | mandatory | A list of information about each optical receiver in a fiber node. |
| 1.3.6.1.4.1.5802.1.3.1.2.3.7.1.1.1 | ColumndhtFnOpticalReceiverIndex | read-only | mandatory | Index into dhtFnOpticalReceiverTable. This index is application specific. It can be either the nth receiver, or a slot number. For example, a node may have 4 r… |
| 1.3.6.1.4.1.5802.1.3.1.2.3.7.1.1.2 | ColumndhtFnOpticalReceiverType | read-only | optional | Type of optical receiver. |
| 1.3.6.1.4.1.5802.1.3.1.2.3.8 | ScalardhtInetNetworkAddressType | read-only | deprecated | The address type of DHT's RF interface IP address assigned by the DHCP server. Values: unknown(0), ipv4(1), ipv6(2), ipv4z(3), ipv6z(4), dns(16) The update of … |
| 1.3.6.1.4.1.5802.1.3.1.2.3.9 | ScalardhtInetNetworkAddress | read-only | deprecated | This is the DHT's RF interface IP address assigned by the DHCP Server. Deprecated. Has been move into electrolineCommon branch. |
| 1.3.6.1.4.1.5802.1.3.1.2.3.10 | ScalardhtInetMonitoringNetworkAddressType | read-only | deprecated | The address type of DHT's RF interface IP address assigned by the DHCP server as monitoring interface in DualIp mode. Values: unknown(0), ipv4(1), ipv6(2), ipv… |
| 1.3.6.1.4.1.5802.1.3.1.2.3.11 | ScalardhtInetMonitoringNetworkAddress | read-only | deprecated | This is the DHT's RF interface IP address assigned by the DHCP Server as monitoring interface in DualIp mode. Deprecated. Has been move into electrolineCommon … |
| 1.3.6.1.4.1.5802.1.3.1.2.10 | NodedhtSleepModeEvent | This is the SNMP trap that is generated just before the DHT enters sleep mode. See also dhtCfgBatterySave for more information. | ||
| 1.3.6.1.4.1.5802.1.3.1.2.11 | NodedhtAlarmAssuranceEvent | This SNMP trap is used for alarm assurance. The dhtTrapAckValue indicates the number of alarms sent since the startup or reset of the DHT. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| HundredthsVolts | INTEGER (0..65535) | current | suggests that a Hundredths value of 1234 be rendered as 12.34 Volts |
| TenthdB | Integer32 | current | This data type represents the pad value that are normally expressed in dB. Units are in tenths of a dB; for example, 5.1 dB will be represented as 51. |
| TenthdBmV | Integer32 | current | This data type represents power levels that are normally expressed in dBmV. Units are in tenths of a dBmV; for example, 5.1 dBmV will be represented as 51. |