ELECTROLINE-DVM-STATUS-MIB
41 objects
No module-level DESCRIPTION found.
Imported Objects
| ELECTROLINE-DVM-ROOT-MIB | dvmStatus electrolineDVM |
| IF-MIB | ifIndex |
| RFC1155-SMI | NetworkAddress |
| RFC1213-MIB | DisplayString |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | RowStatus |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5802.1.3.1.3.3.1 | ScalardvmNetworkAddress | read-only | current | This is the RF IP address assigned by the DHCP. |
| 1.3.6.1.4.1.5802.1.3.1.3.3.2 | ScalardvmInternalTemperature | read-only | current | Measured temperature inside the NE's case/housing. Units degrees Celsius. |
| 1.3.6.1.4.1.5802.1.3.1.3.3.3 | TabledvmIfDownstreamChannelTable | not-accessible | current | This table describes the attributes of downstream channels (frequency bands) at Dvm's input. |
| 1.3.6.1.4.1.5802.1.3.1.3.3.3.1 | RowdvmIfDownstreamChannelEntry | not-accessible | current | An entry provides a list of attributes for a single downstream channel. |
| 1.3.6.1.4.1.5802.1.3.1.3.3.3.1.1 | ColumndvmIfDownChannelId | read-only | current | The Cable Modem Termination System identification of the downstream channel within this particular MAC interface. if the interface is down, the object returns … |
| 1.3.6.1.4.1.5802.1.3.1.3.3.3.1.2 | ColumndvmIfDownChannelFrequency | read-only | current | The center of the downstream frequency associated with this channel. This object will return the current tuner frequency. |
| 1.3.6.1.4.1.5802.1.3.1.3.3.3.1.3 | ColumndvmIfDownChannelWidth | read-only | current | The bandwidth of this downstream channel. Most implementations are expected to support a channel width of 6 MHz (North America) and/or 8 MHz (Europe). See the … |
| 1.3.6.1.4.1.5802.1.3.1.3.3.3.1.4 | ColumndvmIfDownChannelModulation | read-only | current | The modulation type associated with this downstream channel. If the interface is down, this object either returns the configured value (CMTS), the most current… |
| 1.3.6.1.4.1.5802.1.3.1.3.3.3.1.5 | ColumndvmIfDownChannelInterleave | read-only | current | The Forward Error Correction (FEC) interleaving used for this downstream channel. Values are defined as follows: taps8Increment16(3): protection 5.9/4.1 usec, … |
| 1.3.6.1.4.1.5802.1.3.1.3.3.3.1.6 | ColumndvmIfDownChannelPower | read-only | current | At the DVM, the received power level at the RF front-end. If the interface is down, the value of 0. |
| 1.3.6.1.4.1.5802.1.3.1.3.3.3.1.7 | ColumndvmIfDownChannelAnnex | read-only | current | The value of this object indicates the conformance of the implementation to important regional cable standards. annexA : Annex A from ITU-T J.83 is used. (equi… |
| 1.3.6.1.4.1.5802.1.3.1.3.3.3.1.8 | ColumndvmIfDownChannelSymbolRate | read-only | current | This value indicates the channel rate in Symbol per second |
| 1.3.6.1.4.1.5802.1.3.1.3.3.3.1.9 | ColumndvmIfDownChannelTunerModule | read-only | current | The value of this object indicates the tuner module number on which the hardware channel is mapped. 1 and 2 are wideband tuners internal to the BCM3380; 3 to 6… |
| 1.3.6.1.4.1.5802.1.3.1.3.3.4 | TabledvmIfUpstreamChannelTable | not-accessible | current | This table describes the attributes of attached upstream channels. |
| 1.3.6.1.4.1.5802.1.3.1.3.3.4.1 | RowdvmIfUpstreamChannelEntry | not-accessible | current | List of attributes for a single upstream channel. |
| 1.3.6.1.4.1.5802.1.3.1.3.3.4.1.1 | ColumndvmIfUpChannelId | read-only | current | The CMTS identification of the upstream channel. |
| 1.3.6.1.4.1.5802.1.3.1.3.3.4.1.2 | ColumndvmIfUpChannelFrequency | read-only | current | The center of the frequency band associated with this upstream interface. This object returns 0 if the frequency is undefined or unknown. Minimum permitted ups… |
| 1.3.6.1.4.1.5802.1.3.1.3.3.4.1.3 | ColumndvmIfUpChannelWidth | read-only | current | The bandwidth of this upstream interface. This object returns 0 if the interface width is undefined or unknown. Minimum permitted interface width is currently … |
| 1.3.6.1.4.1.5802.1.3.1.3.3.4.1.4 | ColumndvmIfUpChannelTxPower | read-only | current | The operational transmit power for the attached upstream channel at the output of the DVM.E |
| 1.3.6.1.4.1.5802.1.3.1.3.3.4.1.5 | ColumndvmIfUpChannelSymbolRate | read-only | current | This value indicates the channel rate in kSymbol per second |
| 1.3.6.1.4.1.5802.1.3.1.3.3.5 | TabledvmIfSignalQualityTable | not-accessible | current | At the CM, describes the PHY signal quality of downstream channels. |
| 1.3.6.1.4.1.5802.1.3.1.3.3.5.1 | RowdvmIfSignalQualityEntry | not-accessible | current | At the CM, this object describes the PHY characteristics of a downstream channel. |
| 1.3.6.1.4.1.5802.1.3.1.3.3.5.1.1 | ColumndvmIfSigQUnerroreds | read-only | current | Codewords received on this channel without error. This includes all codewords, whether or not they were part of frames destined for this device. Discontinuitie… |
| 1.3.6.1.4.1.5802.1.3.1.3.3.5.1.2 | ColumndvmIfSigQCorrecteds | read-only | current | Codewords received on this channel with correctable errors. This includes all codewords, whether or not they were part of frames destined for this device. Disc… |
| 1.3.6.1.4.1.5802.1.3.1.3.3.5.1.3 | ColumndvmIfSigQUncorrectables | read-only | current | Codewords received on this channel with uncorrectable errors. This includes all codewords, whether or not they were part of frames destined for this device. Di… |
| 1.3.6.1.4.1.5802.1.3.1.3.3.5.1.4 | ColumndvmIfSigQSignalNoise | read-only | current | Signal/Noise ratio as perceived for this channel. At the CM, this object describes the Signal/Noise of the downstream channel. |
| 1.3.6.1.4.1.5802.1.3.1.3.3.5.1.5 | ColumndvmIfSigQMicroreflections | read-only | current | Microreflections, including in-channel response as perceived on this interface, measured in dBc below the signal level. This object is not assumed to return an… |
| 1.3.6.1.4.1.5802.1.3.1.3.3.6 | ScalardvmRxAttenuatorPad | read-only | current | The Rx Attenuator pad value. If value is -2,0 the pad sens technology is not connected. Check the wiring inside the DVM If value is -1,0 there is no pad connec… |
| 1.3.6.1.4.1.5802.1.3.1.3.3.7 | ScalardvmTxAttenuatorPad | read-only | current | The Tx Attenuator pad value. If value is -2,0 the pad sens technology is not connected. Check the wiring inside the DVM If value is -1,0 there is no pad connec… |
| 1.3.6.1.4.1.5802.1.3.1.3.3.8 | ScalardvmRxEqualyzerPlugin | read-only | current | The Equalyzer plugin value. Could be a cable simulator or a equilazer. If value is -2,0 the pad sens technology is not connected. Check the wiring inside the D… |
| 1.3.6.1.4.1.5802.1.3.1.3.3.9 | ScalardvmAcInputVoltage | read-only | current | Returns the dvm Ac input voltage. Units 1VAC. |
| 1.3.6.1.4.1.5802.1.3.1.3.3.10 | ScalardvmNumberDCPowerSupply | read-only | current | Number of entries in the internal DC power supply table A zero entry means the table does not exist and the functional area is not present in the device. |
| 1.3.6.1.4.1.5802.1.3.1.3.3.11 | TabledvmDCPowerTable | not-accessible | current | A table containing information about the Regulated Power. |
| 1.3.6.1.4.1.5802.1.3.1.3.3.11.1 | RowdvmDCPowerEntry | not-accessible | current | A list of information about the Regulated Power. |
| 1.3.6.1.4.1.5802.1.3.1.3.3.11.1.1 | ColumndvmDCPowerIndex | read-only | current | Index into the dvmDCPowerTable. |
| 1.3.6.1.4.1.5802.1.3.1.3.3.11.1.2 | ColumndvmDCPowerVoltage | read-only | current | Returns the regulated power voltage. Units in 0.01 Volts. |
| 1.3.6.1.4.1.5802.1.3.1.3.3.11.1.3 | ColumndvmDCPowerName | read-only | current | Identifies the Physical name of the Power Supply. For example: 3.3V Supply |
| 1.3.6.1.4.1.5802.1.3.1.3.3.12 | ScalardvmTunerHeaterStatus | read-only | current | This mib shows the tuner heater block activation status. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| HundredthsVolts | INTEGER (0..65535) | current | suggests that a Hundredths value of 1234 be rendered as 12.34 Volts |
| TenthdB | Integer32 | current | This data type represents the pad value that are normally expressed in dB. Units are in tenths of a dB; for example, 5.1 dB will be represented as 51. |
| TenthdBmV | Integer32 | current | This data type represents power levels that are normally expressed in dBmV. Units are in tenths of a dBmV; for example, 5.1 dBmV will be represented as 51. |