ELS100-S24TX2M-MIB
50 objects
The MIB module for ELS100-S24TX2M.
Imported Objects
| RFC1155-SMI | internet |
| SNMPv2-SMI | Integer32 IpAddress MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.52.3.9.1.10.7 | IdentitytpELS100S24TX2M | The MIB module for ELS100-S24TX2M. | ||
| 1.3.6.1.4.1.52.3.9.1.10.7.1 | NodeswitchInfo | |||
| 1.3.6.1.4.1.52.3.9.1.10.7.1.1 | ScalarswitchNumber | read-only | current | The total number of switches present on this system. |
| 1.3.6.1.4.1.52.3.9.1.10.7.1.2 | TableswitchInfoTable | not-accessible | current | Table of descriptive and status information about switches in this system. |
| 1.3.6.1.4.1.52.3.9.1.10.7.1.2.1 | RowswitchInfoEntry | not-accessible | current | An entry in the table, containing information about a single switch in this system. |
| 1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.1 | ColumnswUnitIndex | not-accessible | current | This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber. |
| 1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.2 | ColumnswMainBoardHwVer | read-only | current | Hardware version of the main board. |
| 1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.3 | ColumnswMainBoardFwVer | read-only | current | Firmware version of the main board. |
| 1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.4 | ColumnswAgentBoardHwVer | read-only | current | Hardware version of the agent board. |
| 1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.5 | ColumnswAgentBoardFwVer | read-only | current | Firmware version of the agent board. |
| 1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.6 | ColumnswAgentBoardPOSTCodeVer | read-only | current | POST code version of the agent board. |
| 1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.7 | ColumnswPortNumber | read-only | current | The total port number of this switch (including expansion slot). |
| 1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.8 | ColumnswPowerStatus | read-only | current | Indicates the switch using internalPower(1), redundantPower(2) or both(3) |
| 1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.9 | ColumnswExpansionSlot1 | read-only | current | Type of expansion module in this switch slot 1. |
| 1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.10 | ColumnswExpansionSlot2 | read-only | current | Type of expansion module in this switch slot 2. |
| 1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.11 | ColumnswRoleInSystem | read-only | current | Indicates the switch is master(1), backupMaster(2) or slave(3) in this system. |
| 1.3.6.1.4.1.52.3.9.1.10.7.1.3 | TableswitchOIDTable | not-accessible | current | Table of System Object Identifiers for switches in this system. |
| 1.3.6.1.4.1.52.3.9.1.10.7.1.3.1 | RowswitchOIDEntry | not-accessible | current | An entry in the table, containing System Object Identifier for a single switch in this system. |
| 1.3.6.1.4.1.52.3.9.1.10.7.1.3.1.1 | ColumnswitchOIDIndex | not-accessible | current | This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber. Index value 1… |
| 1.3.6.1.4.1.52.3.9.1.10.7.1.3.1.2 | ColumnswitchOIDValue | read-only | current | This object contains the System Object Identifier that uniquely identifies the type of switch. |
| 1.3.6.1.4.1.52.3.9.1.10.7.2 | NodeswitchPortMgt | |||
| 1.3.6.1.4.1.52.3.9.1.10.7.2.1 | TableswitchPortMgtTable | not-accessible | current | Table of descriptive and status information about configuration of each switch ports (including expansion slot) in this system. |
| 1.3.6.1.4.1.52.3.9.1.10.7.2.1.1 | RowswitchPortMgtEntry | not-accessible | current | An entry in the table, containing information about configuration in one switch port of the switch. |
| 1.3.6.1.4.1.52.3.9.1.10.7.2.1.1.1 | ColumnswPortMgtIndex | not-accessible | current | This object identifies the port within the switch for which this entry contains information. |
| 1.3.6.1.4.1.52.3.9.1.10.7.2.1.1.2 | ColumnswPortMgtPortType | read-only | current | Indicates the port type is tenBaseT/hundredBaseTX(1), hundredBaseFX(2) or thousandBaseSX(3). |
| 1.3.6.1.4.1.52.3.9.1.10.7.2.1.1.3 | ColumnswPortMgtSpeedDpxAdmin | read-write | current | Set the port speed and duplex mode as follows: halfDuplex10(1) - 10Mbps and half duplex mode fullDuplex10(2) - 10Mbps and full duplex mode halfDuplex100(3) - 1… |
| 1.3.6.1.4.1.52.3.9.1.10.7.2.1.1.4 | ColumnswPortMgtSpeedDpxInUse | read-only | current | The operating speed and duplex mode of the switched port. |
| 1.3.6.1.4.1.52.3.9.1.10.7.2.1.1.5 | ColumnswPortMgtFlowCtrlAdmin | read-write | current | (1) Flow control mechanism is enabled. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPr… |
| 1.3.6.1.4.1.52.3.9.1.10.7.2.1.1.6 | ColumnswPortMgtFlowCtrlInUse | read-only | current | (1) BackPressure flow control mechanism is used. (2) IEEE 802.3 flow control mechanism is used. (3) Flow control mechanism is disabled. |
| 1.3.6.1.4.1.52.3.9.1.10.7.3 | NodesystemSTAMgt | |||
| 1.3.6.1.4.1.52.3.9.1.10.7.3.1 | ScalarsystemSTAStatus | read-write | current | Global spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled. |
| 1.3.6.1.4.1.52.3.9.1.10.7.4 | NodetftpDownloadMgt | |||
| 1.3.6.1.4.1.52.3.9.1.10.7.4.1 | ScalartftpDownloadServerIP | read-write | current | The IP address of a TFTP server from which a firmware image can be downloaded. |
| 1.3.6.1.4.1.52.3.9.1.10.7.4.2 | ScalartftpDownloadAgentBoardFwFileName | read-write | current | |
| 1.3.6.1.4.1.52.3.9.1.10.7.4.3 | ScalartftpDownloadAgentBoardFwDownloadNode | read-write | current | Indicates whether a newly upgraded firmware version should write to flash. When this object is temporary(2), following a successful upgrade the system will swi… |
| 1.3.6.1.4.1.52.3.9.1.10.7.4.4 | ScalartftpDownloadStatus | read-write | current | Setting this object to active(1) trigger the TFTP download action. Setting this object to notActive(2) has no effect. The system always returns the value notAc… |
| 1.3.6.1.4.1.52.3.9.1.10.7.5 | NoderestartMgt | |||
| 1.3.6.1.4.1.52.3.9.1.10.7.5.1 | ScalarrestartOptionPOST | read-write | current | Setting this object as enabled. The system will do POST when it restart |
| 1.3.6.1.4.1.52.3.9.1.10.7.5.2 | ScalarrestartOptionReloadFactoryDefault | read-write | current | Setting this object as enabled. The system will do factory reset when it restart |
| 1.3.6.1.4.1.52.3.9.1.10.7.5.3 | ScalarrestartOptionKeepIpSetting | read-write | current | Setting this object as enabled. The system will keep IP setting when it do factory reset. |
| 1.3.6.1.4.1.52.3.9.1.10.7.5.4 | ScalarrestartOptionKeepUserAuthentication | read-write | current | Setting this object as enabled. The system will keep user authentication setting when it do factory reset. |
| 1.3.6.1.4.1.52.3.9.1.10.7.5.5 | ScalarrestartAction | read-write | current | Setting this object to active(1) trigger the system restart. Setting this object to notActive(2) has no effect. The system always returns the value notActive(2… |
| 1.3.6.1.4.1.52.3.9.1.10.7.6 | NodeportMirrorMgt | |||
| 1.3.6.1.4.1.52.3.9.1.10.7.6.1 | ScalarportMirrorStatus | read-write | current | Port mirroring function status. (1) mirroring function is enabled. (2) mirroring function is disabled. |
| 1.3.6.1.4.1.52.3.9.1.10.7.6.2 | ScalarportMirrorSnifferPort | read-write | current | Linear port number of sniffer port to which all frames to/from mirrored ports are sent. Frames are only mirrored if the portMirrorStatus object is set to enabl… |
| 1.3.6.1.4.1.52.3.9.1.10.7.6.3 | ScalarportMirrorMirroredPort | read-write | current | Linear port number of mirrored port. The traffic of mirrored port will be 'copied' to sniffer port. |
| 1.3.6.1.4.1.52.3.9.1.10.7.7 | NodeigmpMgt | |||
| 1.3.6.1.4.1.52.3.9.1.10.7.7.1 | ScalarigmpStatus | read-write | current | Parameter to enable or disable IGMP snooping on the device. When enabled, the device will examine IGMP packets and set up filters for IGMP ports. The default i… |
| 1.3.6.1.4.1.52.3.9.1.10.7.7.2 | ScalarigmpQueryCount | read-write | current | Maximum number of queries that have not been heard on the system before the system starts taking action to solicit reports(default is 5). |
| 1.3.6.1.4.1.52.3.9.1.10.7.7.3 | ScalarigmpReportDelay | read-write | current | Timeout value(mins) between IGMP reports received on a port for an IP Multicast Address that can pass before the system sends an IGMP Query out the port and re… |