MIB Viewer

ENTERASYS-CONVERGENCE-END-POINT-MIB

70 objects
This MIB module defines a portion of the SNMP MIB under Enterasys Networks enterprise OID pertaining to Convergence End Point management.
Imported Objects
ENTERASYS-MIB-NAMESetsysModules
IF-MIBifIndex InterfaceIndex
INET-ADDRESS-MIBInetAddress InetAddressType
P-BRIDGE-MIBEnabledStatus
SNMP-FRAMEWORK-MIBSnmpAdminString
SNMPv2-CONFMODULE-COMPLIANCE OBJECT-GROUP
SNMPv2-SMIInteger32 MODULE-IDENTITY OBJECT-TYPE
SNMPv2-TCDateAndTime MacAddress RowStatus TEXTUAL-CONVENTION TruthValue
OIDNameAccessStatusDescription
1.3.6.1.4.1.5624.1.2.40IdentityetsysConvergenceEndPointMIBThis MIB module defines a portion of the SNMP MIB under Enterasys Networks enterprise OID pertaining to Convergence End Point management.
1.3.6.1.4.1.5624.1.2.40.1NodeetsysConvEndPointObjects
1.3.6.1.4.1.5624.1.2.40.1.1NodeetsysConvEndPointConfig
1.3.6.1.4.1.5624.1.2.40.1.1.1ScalaretsysConvEndPointGlobalConfigEnableread-writecurrentWhen set to enabled(1) this object activates the current Convergence End Point configuration. When set to disabled(2) this MIB SHALL be configurable, but MUST …
1.3.6.1.4.1.5624.1.2.40.1.1.2TableetsysConvEndPointGlobalConfigTablenot-accessiblecurrentThis table represents all Convergence End Point types supported by this entity, and provides a default policy profile for each Convergence End Point type.
1.3.6.1.4.1.5624.1.2.40.1.1.2.1RowetsysConvEndPointGlobalConfigEntrynot-accessiblecurrentDefines the default policy to be applied when this type of Convergence End Point is detected or discovered.
1.3.6.1.4.1.5624.1.2.40.1.1.2.1.1ColumnetsysConvEndPointGlobalEndPointTypenot-accessiblecurrentThe Convergence End Point type. The value of this object is limited to a single enumerated bit in the ConvEndPointTypes textual convention.
1.3.6.1.4.1.5624.1.2.40.1.1.2.1.2ColumnetsysConvEndPointGlobalDefaultPolicyIndexread-writecurrentThe policy that should be applied for this type of Convergence End Point. This value is an etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-M…
1.3.6.1.4.1.5624.1.2.40.1.1.3TableetsysConvEndPointProtocolConfigTablenot-accessiblecurrentThis table provides control of Convergence End Point detection and discovery on a per interface and per Convergence End Point type basis. Maintaining the value…
1.3.6.1.4.1.5624.1.2.40.1.1.3.1RowetsysConvEndPointProtocolConfigEntrynot-accessiblecurrentThe current Convergence End Point detection and discovery status for an interface.
1.3.6.1.4.1.5624.1.2.40.1.1.3.1.1ColumnetsysConvEndPointProtocolEndPointTypenot-accessiblecurrentThe Convergence End Point type.
1.3.6.1.4.1.5624.1.2.40.1.1.3.1.2ColumnetsysConvEndPointProtocolEnableread-writecurrentWhen set to enabled(1), Convergence End Point detection and discovery will be enabled on this interface for the Convergence End Point type specified. When set …
1.3.6.1.4.1.5624.1.2.40.1.2NodeetsysConvEndPointStatus
1.3.6.1.4.1.5624.1.2.40.1.2.1TableetsysConvEndPointConnMacTablenot-accessibledeprecatedThis table provides information on each of the Convergence End Points that has been discovered or detected by this entity. Maintaining the value of this object…
1.3.6.1.4.1.5624.1.2.40.1.2.1.1RowetsysConvEndPointConnMacEntrynot-accessibledeprecatedInformation about an individual Convergence End Point.
1.3.6.1.4.1.5624.1.2.40.1.2.1.1.1ColumnetsysConvEndPointConnMacMacAddressnot-accessibledeprecatedThe MAC address of this Convergence End Point.
1.3.6.1.4.1.5624.1.2.40.1.2.1.1.2ColumnetsysConvEndPointConnMacPortNumberread-onlydeprecatedThe interface on which this Convergence End Point was detected or discovered.
1.3.6.1.4.1.5624.1.2.40.1.2.1.1.3ColumnetsysConvEndPointConnMacEndPointTyperead-onlydeprecatedThe type of Convergence End Point described by this row.
1.3.6.1.4.1.5624.1.2.40.1.2.1.1.4ColumnetsysConvEndPointConnMacPolicyIndexread-onlydeprecatedThe policy applied for this Convergence End Point. This value is an etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-MIB. If the desired poli…
1.3.6.1.4.1.5624.1.2.40.1.2.1.1.5ColumnetsysConvEndPointConnMacDiscoveryTimeread-onlydeprecatedThe time and date that this Convergence End Point was detected or discovered.
1.3.6.1.4.1.5624.1.2.40.1.2.1.1.6ColumnetsysConvEndPointConnMacFirmwareVersionread-onlydeprecatedThis is the firmware version of the discovered Convergence End Point. If this information is not available via the detection protocol then a zero length string…
1.3.6.1.4.1.5624.1.2.40.1.2.1.1.7ColumnetsysConvEndPointConnMacInetAddressTyperead-onlydeprecatedThe address type of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return 'unknown'.
1.3.6.1.4.1.5624.1.2.40.1.2.1.1.8ColumnetsysConvEndPointConnMacInetAddressread-onlydeprecatedThe address of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return a zero length string.
1.3.6.1.4.1.5624.1.2.40.1.2.2TableetsysConvEndPointConnPortTablenot-accessiblecurrentThis table provides a mapping from the entities interfaces to discovered Convergence End Points. Maintaining the value of this object across system reboots is …
1.3.6.1.4.1.5624.1.2.40.1.2.2.1RowetsysConvEndPointConnPortEntrynot-accessiblecurrentInformation about an individual Convergence End Point.
1.3.6.1.4.1.5624.1.2.40.1.2.2.1.1ColumnetsysConvEndPointConnPortMacAddressread-onlycurrentThe MAC address of the discovered or detected Convergence End Point.
1.3.6.1.4.1.5624.1.2.40.1.2.3TableetsysCEPConnMacTablenot-accessiblecurrentThis table provides information on each of the Convergence End Points that has been discovered or detected by this entity. Maintaining the value of this object…
1.3.6.1.4.1.5624.1.2.40.1.2.3.1RowetsysCEPConnMacEntrynot-accessiblecurrentInformation about an individual Convergence End Point (CEP).
1.3.6.1.4.1.5624.1.2.40.1.2.3.1.1ColumnetsysCEPConnMacEndPointTyperead-onlycurrentThe type of Convergence End Point described by this row.
1.3.6.1.4.1.5624.1.2.40.1.2.3.1.2ColumnetsysCEPConnMacPolicyIndexread-onlycurrentThe policy applied for this Convergence End Point. This value is an etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-MIB. If the desired poli…
1.3.6.1.4.1.5624.1.2.40.1.2.3.1.3ColumnetsysCEPConnMacDiscoveryTimeread-onlycurrentThe time and date that this Convergence End Point was detected or discovered.
1.3.6.1.4.1.5624.1.2.40.1.2.3.1.4ColumnetsysCEPConnMacFirmwareVersionread-onlycurrentThis is the firmware version of the discovered Convergence End Point. If this information is not available via the detection protocol then a zero length string…
1.3.6.1.4.1.5624.1.2.40.1.2.3.1.5ColumnetsysCEPConnMacInetAddressTyperead-onlycurrentThe address type of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return 'unknown'.
1.3.6.1.4.1.5624.1.2.40.1.2.3.1.6ColumnetsysCEPConnMacInetAddressread-onlycurrentThe address of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return a zero length string.
1.3.6.1.4.1.5624.1.2.40.1.3NodeetsysConvEndPointDetection
1.3.6.1.4.1.5624.1.2.40.1.3.1ScalaretsysConvEndPointDetectionMaxEntriesread-onlycurrentThis value represents the maximum number of entries allowed in the etsysConvEndPointDetectionTable.
1.3.6.1.4.1.5624.1.2.40.1.3.2TableetsysConvEndPointDetectionTablenot-accessiblecurrentA table that describes the IP address and IP port based Convergence End Point detection parameters. Packets on interfaces that are configured to detect End Poi…
1.3.6.1.4.1.5624.1.2.40.1.3.2.1RowetsysConvEndPointDetectionEntrynot-accessiblecurrentEach entry represents a describes parameters for detecting a Convergence End Point.
1.3.6.1.4.1.5624.1.2.40.1.3.2.1.1ColumnetsysConvEndPointDetectionRuleIndexnot-accessiblecurrentThe index of this conceptual row. This row represents a single rule for determining if an incoming IP packet indicates the presence of a Convergence End Point …
1.3.6.1.4.1.5624.1.2.40.1.3.2.1.2ColumnetsysConvEndPointDetectionEndPointTyperead-createcurrentThe Convergence End Point device type that a 'hit' on this rule will indicate the presence of.
1.3.6.1.4.1.5624.1.2.40.1.3.2.1.3ColumnetsysConvEndPointDetectionProtocolread-createcurrentThe IP protocol type that the following port range applies to. If no bits are set then the destination port will not be evaluated as part of the detection proc…
1.3.6.1.4.1.5624.1.2.40.1.3.2.1.4ColumnetsysConvEndPointDetectionPortLowread-createcurrentThe low end of the range of the IP destination port that will be used for Convergence End Point detection. This value represents the low value in a range of po…
1.3.6.1.4.1.5624.1.2.40.1.3.2.1.5ColumnetsysConvEndPointDetectionPortHighread-createcurrentThe high end of the range of the IP destination port that will be used for Convergence End Point detection. This value represents the high value in a range of …
1.3.6.1.4.1.5624.1.2.40.1.3.2.1.6ColumnetsysConvEndPointDetectionAddrTyperead-createcurrentThe destination address type that will be used for Convergence End Point detection. If the address type is 'unknown', then this value will not be evaluated as …
1.3.6.1.4.1.5624.1.2.40.1.3.2.1.7ColumnetsysConvEndPointDetectionAddrread-createcurrentThe destination IP address that will be used for Convergence End Point detection. If this address is null, then this value will not be evaluated as part of the…
1.3.6.1.4.1.5624.1.2.40.1.3.2.1.8ColumnetsysConvEndPointDetectionAddrMaskTyperead-createcurrentThe address type of the mask that will be applied to the destination IP address as part of the Convergence End Point detection process. If the address type is …
1.3.6.1.4.1.5624.1.2.40.1.3.2.1.9ColumnetsysConvEndPointDetectionAddrMaskread-createcurrentThe destination address mask that will be used for Convergence End Point detection. If the mask is null, then this value will not be evaluated as part of the d…
1.3.6.1.4.1.5624.1.2.40.1.3.2.1.10ColumnetsysConvEndPointDetectionRowStatusread-createcurrentThe status of this row as defined by the RowStatus textual convention. Rows in this table can only transition to 'notInService', or to 'active' if the etsysCon…
1.3.6.1.4.1.5624.1.2.40.1.3.3TableetsysCEPDetectionPortConfigTablenot-accessiblecurrentA table of per port configuration for Convergence End Point detection. Maintaining the value of this object across system reboots is NOT REQUIRED.
1.3.6.1.4.1.5624.1.2.40.1.3.3.1RowetsysCEPDetectionPortConfigEntrynot-accessiblecurrentAn entry containing per port Convergence End Point data. Only interfaces that are able to detect Convergence End Points are represented in this table.
1.3.6.1.4.1.5624.1.2.40.1.3.3.1.1ColumnetsysCEPPortClearUsersread-writecurrentSetting this object to a value of true(1) will cause all detected or discovered Convergence End Points to be removed from the following status tables: etsysCon…
1.3.6.1.4.1.5624.1.2.40.1.3.4TableetsysCEPCdpPortConfigTablenot-accessiblecurrentA table of per port configuration for Convergence End Point detection related to the Cisco CDP protocol. Only ports that are capable of participating in Cisco …
1.3.6.1.4.1.5624.1.2.40.1.3.4.1RowetsysCEPCdpPortConfigEntrynot-accessiblecurrentAn entry containing per port Convergence End Point data. Only interfaces that are able to detect Convergence End Points are represented in this table.
1.3.6.1.4.1.5624.1.2.40.1.3.4.1.1ColumnetsysCEPCiscoCDPVoicePortVlanread-writecurrentThis object controls the behavior of the remote configuration of Cisco VOIP phones via Cisco CDP. Setting this object to a value of -1 will cause the device to…
1.3.6.1.4.1.5624.1.2.40.2NodeetsysConvEndPointConformance
1.3.6.1.4.1.5624.1.2.40.2.1NodeetsysConvEndPointGroups
1.3.6.1.4.1.5624.1.2.40.2.1.1GroupetsysConvEndPointGlobalConfigGroupcurrentObjects which provide global control of the Convergence End Point features.
1.3.6.1.4.1.5624.1.2.40.2.1.2GroupetsysConvEndPointConfigGroupcurrentObjects which provide overrides to the global Convergence End Point controls.
1.3.6.1.4.1.5624.1.2.40.2.1.3GroupetsysConvEndPointDetectionGroupdeprecatedObjects that provide configuration information specific to IP, port, and address based Convergence End Point detection.
1.3.6.1.4.1.5624.1.2.40.2.1.4GroupetsysConvEndPointStatusGroupdeprecatedObjects that provide status information for discovered and detected Convergence End Points.
1.3.6.1.4.1.5624.1.2.40.2.1.5GroupetsysConvEndPointStatusGroup2currentObjects that provide status information for discovered and detected Convergence End Points.
1.3.6.1.4.1.5624.1.2.40.2.1.6GroupetsysConvEndPointDetectionGroup2currentObjects that provide configuration information specific to IP, port, and address based Convergence End Point detection.
1.3.6.1.4.1.5624.1.2.40.2.1.7GroupetsysConvEndPointPortConfigGroupcurrentObjects that provide per port control for discovered and detected Convergence End Points.
1.3.6.1.4.1.5624.1.2.40.2.1.8GroupetsysConvEndPointCiscoVoiceVLANGroupcurrentObjects that provide per port control for configuring Cisco VOIP phones via Cisco CDP.
1.3.6.1.4.1.5624.1.2.40.2.2NodeetsysConvEndPointCompliances
1.3.6.1.4.1.5624.1.2.40.2.2.1ComplianceetsysConvEndPointCompliancedeprecatedThis compliance statement has been deprecated in favor of the etsysConvEndPointCompliance2 group.
1.3.6.1.4.1.5624.1.2.40.2.2.2ComplianceetsysConvEndPointCompliance2currentThe compliance statement for entities which implement the Enterasys Convergence End Point Management MIB.
1.3.6.1.4.1.5624.1.2.40.2.2.3ComplianceetsysConvEndPointPortConfigCompliancecurrentThe compliance statement for devices that support per port configuration of Convergence End Point detection and discovery.
1.3.6.1.4.1.5624.1.2.40.2.2.4ComplianceetsysConvEndPointCiscoVoiceVLANCompliancecurrentThe compliance statement for devices that support detection and configuration of Cisco VOIP phones via Cisco CDP.
Type Definitions
NameSyntaxStatusDescription
ConvEndPointTypesBITS { ciscoIPphone(0), siemensIPphone(1), avayaCLan(2), avayaMedPro(3), genericH323(4), sip(5), lldpMed(6) }currentSupported Convergence End Point products.