FS-INTERFACE-MIB
266 objects
This module defines fs interface mibs.
Imported Objects
| FS-SMI | fsMgmt |
| FS-TC | ConfigStatus IfIndex |
| IANAifType-MIB | IANAifType |
| IF-MIB | InterfaceIndex |
| INET-ADDRESS-MIB | -- RFC3411 InetAddressType InetAddress |
| P-BRIDGE-MIB | EnabledStatus |
| Q-BRIDGE-MIB | VlanId |
| RFC1155-SMI | Gauge TimeTicks |
| RFC1213-MIB | ifIndex |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DateAndTime DisplayString MacAddress PhysAddress RowStatus |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.52642.1.1.10.2.10 | IdentityfsInterfaceMIB | This module defines fs interface mibs. | ||
| 1.3.6.1.4.1.52642.1.1.10.2.10.1 | NodefsIfConfigMIBObjects | |||
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1 | TablefsIfTable | not-accessible | current | list of interface basic configuration objects. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1 | RowfsIfEntry | not-accessible | current | Entry contains interface basic configurations. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.1 | ColumnfsIfIndex | read-only | current | |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.2 | ColumnfsIfPortType | read-only | current | Port type of this port, list as above. port100MBASEFX indicates that port is port100MBASEFXL or port100MBASEFXS, and system doesn't distinguish. port1000MBASEF… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.3 | ColumnfsIfFlowControlAdminStatus | read-create | current | Flow control of a port management status. This attribute apply physical port and aggreate port |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.4 | ColumnfsIfFlowControlOperStatus | read-only | current | Oper status: after the negotiation between two ports connetted the flow contrl status. This attribute apply physical port and aggreate port |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.5 | ColumnfsIfAdminSpeed | read-create | current | port speed settings. This attribute apply physical port and aggreate port |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.6 | ColumnfsIfAdminDuplex | read-create | current | port duplex settings. This attribute apply physical port and aggreate port |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.7 | ColumnfsIfOperSpeed | read-only | current | After two port have negotiated the speed status,and this object is the working speed status. while the port link status is down , then the speed status is unkn… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.8 | ColumnfsIfOperDuplex | read-only | current | After two port have negotiated the duplex status, and this object is the working duplex status. while the port link status is down , then the speed status is u… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.9 | ColumnfsIfManageStatus | read-create | current | Management status of the interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.10 | ColumnfsIfIpBroadcast | read-create | current | Broadcast address of the interface. if broadcast address not configured on interface, return 0.0.0.0 |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.11 | ColumnfsIfLayer | read-create | current | |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.12 | ColumnfsIfMode | read-create | current | This value is meaning for only physical port and aggreate port |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.13 | ColumnfsIfCounterClear | read-create | current | Setting its to any value but 0, will clear counters of this interface. Setting its value to 0 will cause no action of the agent. and when query will always ret… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.14 | ColumnfsIfEntryStatus | read-create | current | Status of this entry, set this object to valid will create a interface, and set its value to invalid will delete the interface of this entry. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.15 | ColumnfsIfMediumType | read-create | current | Port medium type of this port,fiber or copper. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.16 | ColumnfsIfDownCounter | read-only | current | The counters of linkdown times of the interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.17 | ColumnfsIfInOctets | read-only | current | The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.18 | ColumnfsIfOutOctets | read-only | current | The total number of octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initial… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.19 | ColumnfsIfBcastInhibit | read-write | current | The percentage of the broadcast storm restraint on the interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.20 | ColumnfsIfNegotiation | read-write | current | The negotiation status of the interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.21 | ColumnfsIfPhysAddress | read-only | current | The interface's address at its protocol sub-layer. For example, for an 802.x interface, this object normally contains a MAC address. The interface's media-spec… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.22 | ColumnfsIfAdminSpeedRW | read-write | current | port speed settings. This attribute apply physical port and aggreate port |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.23 | ColumnfsIfAdminDuplexRW | read-write | current | port duplex settings. This attribute apply physical port and aggreate port |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.24 | ColumnfsIfModeRW | read-write | current | This value is meaning for only physical port and aggreate port |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.25 | ColumnfsIfSpeed | read-only | current | An estimate of the interface's current bandwidth in units of Mbits per second. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.26 | ColumnfsifAdminStatus | read-write | current | the interface keeps the admin state . |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.27 | ColumnfsifOperStatus | read-only | current | the interface keeps the oper state . |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.28 | ColumnfsIfInNUcastPkts | read-only | current | The counter of receiving packets contain BROADCAST and PACKET_MULTICAST . |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.29 | ColumnfsIfOutNUcastPkts | read-only | current | The counter of sending packets contain BROADCAST and PACKET_MULTICAST . |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.30 | ColumnfsIfUpDownTimes | read-only | current | The counters of linkup and linkdown times of the interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.31 | ColumnfsifAdminStatusw | read-write | current | The desired state of the interface. When a managed system initializes, all interfaces start with ifAdminStatus in the admindown(1) state. As a result of either… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.32 | ColumnfsifOperStatusw | read-only | current | The current operational state of the interface. If fsApIfAdminStatus is admindown(2) then fsApIfOperStatus should be admindown(2). If fsApIfAdminStatus is chan… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.33 | ColumnfsifSpeedw | read-only | current | An estimate of the interface's current bandwidth in units of Mbits per second. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.34 | ColumnfsifMacAddress | read-only | current | The interface's address at its protocol sub-layer. For example, for an 802.x interface, this object normally contains a MAC address. The interface's media-spec… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.35 | ColumnfsifLastChange | read-only | current | The length of the time that comes current state . |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.36 | ColumnfsIfInPkts | read-only | current | The number of packets received on this interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of … |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.37 | ColumnfsIfDiscard | read-only | current | The number of bound packets which were chosen to be discarded even though no errors. One possible reason for discarding such a packet could be to free up buffe… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.38 | ColumnfsIfBandwidthUsage | read-only | current | Current bandwidth utilization of interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.39 | ColumnfsIfInBitsRate | read-only | current | The average input packet-rate over a period of time(configuration by interface command 'load-interval') in bits per second on this interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.40 | ColumnfsIfInPktRate | read-only | current | The average input packet-rate over a period of time(configuration by interface command 'load-interval') in packets per second on this interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.41 | ColumnfsIfOutBitsRate | read-only | current | The average output packet-rate over a period of time(configuration by interface command 'load-interval') in bits per second on this interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.42 | ColumnfsIfOutPktRate | read-only | current | The average output packet-rate over a period of time(configuration by interface command 'load-interval') in packets per second on this interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.43 | ColumnfsIfInBandwidthUsage | read-only | current | RX bandwidth utilization ratio of interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.44 | ColumnfsIfOutBandwidthUsage | read-only | current | TX bandwidth utilization ratio of interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.45 | ColumnfsIfInErrorPktsRate | read-only | current | Input packet error rate. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.46 | ColumnfsIfOutErrorPktsRate | read-only | current | Output packet error rate. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.47 | ColumnfsIfInDropPktsRate | read-only | current | Input packet discarded rate. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.48 | ColumnfsIfOutDropPktsRate | read-only | current | Output packet discarded rate. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.49 | ColumnfsIfOutNoBuffer | read-only | current | Ouyput drop packet rate on this interface due to resource lack. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.50 | ColumnfsIfOutPkts | read-only | current | The number of packets sent on this interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the … |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.2 | TablefsIfIpTable | not-accessible | current | A list of interface ip configuration entries. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.2.1 | RowfsIfIpEntry | not-accessible | current | An entry containing configuration information applicable to a Layer3 interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.2.1.1 | ColumnfsIfIpIfIndex | read-only | current | A unique value, for each Layer3 interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.2.1.2 | ColumnfsIfIpId | read-only | current | Type of interface ip address. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.2.1.3 | ColumnfsIfIp | read-only | current | Ip address of the interface fsIfIndex refer to. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.2.1.4 | ColumnfsIfIpMask | read-create | current | Ip mask of the interface ip address. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.2.1.5 | ColumnfsIfIpEntryStatus | read-create | current | entry status of this entry. and the means in this enviraments can reffer to the text-convention definition of the RowStatus. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.3 | TablefsIfStatusTable | not-accessible | current | list of interface status. Status information include some error state and result of examining to the interface,etc. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.3.1 | RowfsIfStatusEntry | not-accessible | current | Entry contains interface status information. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.3.1.1 | ColumnfsIfStatusIndex | read-only | current | |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.3.1.2 | ColumnfsIfStatusLoopBackExamine | read-write | current | Setting its to any value but 0, will Checking whether this port or aggreate can receive and send packets normally, It indicates that port or aggreate is normal… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.3.1.3 | ColumnfsIfErrorStatus | read-only | current | Port's error status information |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.3.1.4 | ColumnfsIfLineDetect | read-only | current | When reading this object, system detects the quality of line connecting the port. Detect whether the line is broken or short circuit or not. The meaning of the… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.4 | ScalarfsGlobalIfDisableRecovery | read-write | current | Setting its to any value but 0, the interfaces which is shutted down by some error happened will recovery from disabled status . Setting its value to 0 will ca… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.5 | TablefsPortTypeChooseTable | not-accessible | current | Table of entrance to choose port type. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.5.1 | RowfsPortTypeChooseEntry | not-accessible | current | Entrance to choose port type. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.5.1.1 | ColumnfsPortTypeChooseIndex | read-only | current | The logic port number. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.5.1.2 | ColumnfsPortTypeChooseType | read-only | current | The chosen port type. This object is used to choose one of the multiple physical ports of different types, when the same logical port is correspondent with the… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.6 | TablefsIfMTUTable | not-accessible | current | Access table of MTU on interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.6.1 | RowfsIfMTUEntry | not-accessible | current | Interfac MTU access. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.6.1.1 | ColumnfsIfMTUIndex | read-only | current | Interface number |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.6.1.2 | ColumnfsIfMTU | read-write | current | Interface MTU. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.7 | TablefsIfAvailableBWTable | not-accessible | current | Access table of Available Bandwidth on interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.7.1 | RowfsIfAvailableBWEntry | not-accessible | current | Interfac available bandwidth access. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.7.1.1 | ColumnfsIfAvailableBWIfIndex | read-only | current | Interface number |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.7.1.2 | ColumnfsIfAvailableBWIfBW | read-only | current | Interface available bandwidth(bit). |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.8 | TablefsIfSVICreatTable | not-accessible | current | Access table of Available Bandwidth on interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.8.1 | RowfsIfSVICreatEntry | not-accessible | current | Interfac available bandwidth access. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.8.1.1 | ColumnfsIfSVICreatVlanNum | read-only | current | Interface Vlan number |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.8.1.2 | ColumnfsIfHandleSVI | read-write | current | 0 creat,1 delete. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.9 | ScalarfsIfPhyIntNum | read-only | current | The number of physical interfaces (regardless of their current state) present on this system. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.10 | TablefsIfLinkUPTimesTable | not-accessible | current | Access table of Available Bandwidth on interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.10.1 | RowfsIfLinkUPTimesEntry | not-accessible | current | Interfac available bandwidth access. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.10.1.1 | ColumnfsInterfaceIndex | read-only | current | Interface Index |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.10.1.2 | ColumnfsIfLinkUPTimes | read-only | current | Vlaues Of Linkup Times. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.11 | TablefsIfEncapsulationTable | not-accessible | current | Access table of Encapsulation dot1q VLAN on interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.11.1 | RowfsIfEncapsulationEntry | not-accessible | current | Interfac encapsulation dot1q VLAN access. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.11.1.1 | ColumnfsIfEncapsulationIndex | read-only | current | A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.11.1.2 | ColumnfsIfEncapsulationVlan | read-write | current | The value indicate the VID of the dot1q vlan encapsulation. The value 0 means de-encapsulation. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.12 | TablefsApIfNumberTable | not-accessible | current | Access table of ap interface number. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.12.1 | RowfsApIfNumberEntry | not-accessible | current | Interfac number of ap. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.12.1.1 | ColumnfsApPhyAddress | read-only | current | The ap's address at its protocol sub-layer. The ap's media-specific MIB must define the bit and byte ordering and the format of the value of this object. For i… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.12.1.2 | ColumnfsApIfNumber | read-only | current | Vlaues Of interface number. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.12.1.3 | ColumnfsApIfPhyIntNum | read-only | current | Vlaues Of physical interface number. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13 | TablefsApIfTable | not-accessible | current | A list of fsAp interface entries. The number of entries is given by the value of fsApIfNumber. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1 | RowfsApIfEntry | not-accessible | current | An entry containing management information fsApplicable to a particular interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.1 | ColumnfsApPhysAddress | read-only | current | The ap's address at its protocol sub-layer. The ap's media-specific MIB must define the bit and byte ordering and the format of the value of this object. For i… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.2 | ColumnfsApIfIndex | read-only | current | A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface su… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.3 | ColumnfsApIfDescr | read-only | current | A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the i… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.4 | ColumnfsApIfType | read-only | current | The type of interface. Additional values for ifType are assigned by the Internet Assigned Numbers Authority (IANA), through updating the syntax of the IANAifTy… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.5 | ColumnfsApIfMtu | read-only | current | The size of the largest packet which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagram… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.6 | ColumnfsApIfSpeed | read-only | current | An estimate of the interface's current bandwidth in units of Mbits per second. For interfaces which do not vary in bandwidth or for those where no accurate est… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.7 | ColumnfsApIfPhysAddress | read-only | current | The interface's address at its protocol sub-layer. For example, for an 802.x interface, this object normally contains a MAC address. The interface's media-spec… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.8 | ColumnfsApIfAdminStatus | read-write | current | The desired state of the interface. The testing(3) state indicates that no operational packets can be passed. When a managed system initializes, all interfaces… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.9 | ColumnfsApIfOperStatus | read-only | current | The current operational state of the interface. If fsApIfAdminStatus is admindown(2) then fsApIfOperStatus should be admindown(3). If fsApIfAdminStatus is chan… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.10 | ColumnfsApIfLastChange | read-only | current | The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re-initialization of… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.11 | ColumnfsApIfInOctets | read-only | current | The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.12 | ColumnfsApIfInUcastPkts | read-only | current | The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Dis… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.13 | ColumnfsApIfInNUcastPkts | read-only | deprecated | The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast or broadcast address at this sub-layer. Discont… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.14 | ColumnfsApIfInDiscards | read-only | current | The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer pr… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.15 | ColumnfsApIfInErrors | read-only | current | For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For char… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.16 | ColumnfsApIfInUnknownProtos | read-only | current | For packet-oriented interfaces, the number of packets received via the interface which were discarded because of an unknown or unsupported protocol. For charac… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.17 | ColumnfsApIfOutOctets | read-only | current | The total number of octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initial… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.18 | ColumnfsApIfOutUcastPkts | read-only | current | The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.19 | ColumnfsApIfOutNUcastPkts | read-only | deprecated | The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast or broadcast address at this sub-laye… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.20 | ColumnfsApIfOutDiscards | read-only | current | The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reaso… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.21 | ColumnfsApIfOutErrors | read-only | current | For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfac… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.22 | ColumnfsApIfOutQLen | read-only | deprecated | The length of the output packet queue (in packets). |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.23 | ColumnfsApIfLinkUPTimes | read-only | current | Vlaues Of Linkup Times. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.24 | ColumnfsApIfInDataOctets | read-only | current | The data octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the man… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.25 | ColumnfsApIfOutDataOctets | read-only | current | The data octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of … |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.26 | ColumnfsApIfMgmtUploadOctets | read-only | current | The upload octets received on the mgmt interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of … |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.27 | ColumnfsApIfMgmtDownloadOctets | read-only | current | The download octets transmitted out of the mgmt interface, including framing characters. Discontinuities in the value of this counter can occur at re-initializ… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.28 | ColumnfsApIfSpeedw | read-only | current | An estimate of the interface's current bandwidth in units of Mbits per second. For interfaces which do not vary in bandwidth or for those where no accurate est… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.29 | ColumnfsApIfMtuw | read-only | current | The size of the largest packet which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagram… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.30 | ColumnfsApIfPhysAddressw | read-only | current | The interface's address at its protocol sub-layer. For example, for an 802.x interface, this object normally contains a MAC address. The interface's media-spec… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.31 | ColumnfsApIfInUcastPktsw | read-only | current | The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Dis… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.32 | ColumnfsApIfInNUcastPktsw | read-only | deprecated | The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast or broadcast address at this sub-layer. Discont… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.33 | ColumnfsApIfOutUcastPktsw | read-only | current | The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.34 | ColumnfsApIfOutNUcastPktsw | read-only | deprecated | The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast or broadcast address at this sub-laye… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.35 | ColumnfsApIfLinkUPTimesw | read-only | current | The counters of linkup and linkdown times of the interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.36 | ColumnfsApIfInPkts | read-only | current | The total number of packets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initializatio… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.37 | ColumnfsApIfInFlow | read-only | current | The flow rate of data octets in units of Bytes per-second received on the interface, including framing characters. Discontinuities in the value of this counter… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.38 | ColumnfsApIfOutFlow | read-only | current | The flow rate of data octets in units of Bytes per-second transmitted out of the interface, including framing characters. Discontinuities in the value of this … |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.39 | ColumnfsApIfInBrdcastPkts | read-only | current | The total number of broadcast packets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-ini… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.40 | ColumnfsApIfOutBrdcastPkts | read-only | current | The total number of broadcast packets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.41 | ColumnfsApIfInMulcastPkts | read-only | current | The total number of multicast packets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-ini… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.42 | ColumnfsApIfOutMulcastPkts | read-only | current | The total number of multicast packets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.43 | ColumnfsApIfInPayloadOctets | read-only | current | The total number of payload octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initia… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.44 | ColumnfsApIfOutPayloadOctets | read-only | current | The total number of payload octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.45 | ColumnfsApIfAlias | read-only | current | A textual string containing alias information about the interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.46 | ColumnfsApIfInDateRate | read-only | current | The flow rate of data octets in units of Kilo-Bits per-second received on the interface, including framing characters. Discontinuities in the value of this cou… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.47 | ColumnfsApIfOutDateRate | read-only | current | The flow rate of data octets in units of Kilo-Bits per-second transmitted out of the interface, including framing characters. Discontinuities in the value of t… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.48 | ColumnfsApifInNormalPkts | read-only | current | The total number of normal packets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initia… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.49 | ColumnfsApIfOutPkts | read-only | current | The total number of packets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initia… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14 | TablefsIfLinkTable | not-accessible | current | A list of interface entries. The number of entries is given by the value of ifNumber. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1 | RowfsIfLinkEntry | not-accessible | current | An entry containing management information applicable to a particular interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.1 | ColumnfsIfLinkIndex | read-only | current | A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface su… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.2 | ColumnfsIfUplinkInOctets | read-only | current | The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.3 | ColumnfsIfUplinkInUcastPkts | read-only | current | The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Dis… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.4 | ColumnfsIfUplinkInNUcastPkts | read-only | deprecated | The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast or broadcast address at this sub-layer. Discont… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.5 | ColumnfsIfUplinkInDiscards | read-only | current | The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer pr… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.6 | ColumnfsIfUplinkInErrors | read-only | current | For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For char… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.7 | ColumnfsIfUplinkOutOctets | read-only | current | The total number of octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initial… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.8 | ColumnfsIfUplinkOutUcastPkts | read-only | current | The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.9 | ColumnfsIfUplinkOutNUcastPkts | read-only | deprecated | The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast or broadcast address at this sub-laye… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.10 | ColumnfsIfUplinkOutDiscards | read-only | current | The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reaso… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.11 | ColumnfsIfUplinkOutErrors | read-only | current | For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfac… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.12 | ColumnfsIfDownlinkInOctets | read-only | current | The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.13 | ColumnfsIfDownlinkInUcastPkts | read-only | current | The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Dis… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.14 | ColumnfsIfDownlinkInNUcastPkts | read-only | deprecated | The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast or broadcast address at this sub-layer. Discont… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.15 | ColumnfsIfDownlinkInDiscards | read-only | current | The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer pr… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.16 | ColumnfsIfDownlinkInErrors | read-only | current | For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For char… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.17 | ColumnfsIfDownlinkOutOctets | read-only | current | The total number of octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initial… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.18 | ColumnfsIfDownlinkOutUcastPkts | read-only | current | The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.19 | ColumnfsIfDownlinkOutNUcastPkts | read-only | deprecated | The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast or broadcast address at this sub-laye… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.20 | ColumnfsIfDownlinkOutDiscards | read-only | current | The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reaso… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.21 | ColumnfsIfDownlinkOutErrors | read-only | current | For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfac… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.22 | ColumnfsIfUplinkInBcastPkts | read-only | current | The number of upbound and inbound packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. … |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.23 | ColumnfsIfUplinkOutBcastPkts | read-only | current | The number of upbound and outbound packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer.… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.24 | ColumnfsIfDownlinkInBcastPkts | read-only | current | The number of downbound and inbound packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.25 | ColumnfsIfDownlinkOutBcastPkts | read-only | current | The number of downbound and outbound packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-laye… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15 | NodefsIfTrafficStatisticsObjects | |||
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.1 | NodefsIfLinkTrafficStatistics | |||
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.1.1 | TablefsIfLinkTrafficTable | not-accessible | current | A table of link traffic statistics, including interface rate and bandwidth utilization. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.1.1.1 | RowfsIfLinkTrafficEntry | not-accessible | current | The link traffic statistics entry. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.1.1.1.1 | ColumnfsIfLinkTrafficIndex | read-only | current | The link traffic interface index. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.1.1.1.2 | ColumnfsIfLinkAvgRate | read-only | current | An estimate of the interface's average bandwidth in units of bits per second. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.1.1.1.3 | ColumnfsIfLinkPeakRate | read-only | current | An estimate of the interface's current peak bandwidth in units of bits per second. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.1.1.1.4 | ColumnfsIfLinkAvgBWUtilization | read-only | current | An estimate of the interface's average bandwidth Utilization. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.1.1.1.5 | ColumnfsIfLinkPeakBWUtilization | read-only | current | An estimate of the interface's current peak bandwidth Utilization. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2 | NodefsIfLinkQosStatistics | |||
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.1 | TablefsLinkQosCtlTable | not-accessible | current | The results of these operations are stored in the fsLinkQosResultsTable |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.1.1 | RowfsLinkQosCtlEntry | not-accessible | current | Defines an entry in the fsLinkQosCtlTable. The first index element, fsLinkQosCtlOwnerIndex, is of type SnmpAdminString, a textual convention that allows for us… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.1.1.1 | ColumnfsLinkQosCtlOwnerIndex | not-accessible | current | To facilitate the provisioning of access control by a security administrator using the View-Based Access Control Model (RFC 2575, VACM) for tables in which mul… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.1.1.2 | ColumnfsLinkQosCtlTestName | not-accessible | current | The name of the ping-based test. This is locally unique, within the scope of a fsLinkQosCtlOwnerIndex. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.1.1.3 | ColumnfsLinkQosCtlTargetAddressType | read-create | current | Specifies the type of host address to be used at a remote host for performing a ping-based operation. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.1.1.4 | ColumnfsLinkQosCtlTargetAddress | read-create | current | Specifies the host address to be used at a remote host for performing a ping-based operation. The host address type is determined by the value of the correspon… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.1.1.5 | ColumnfsLinkQosCtlAdminStatus | read-create | current | Reflects the desired state that a fsLinkQosCtlEntry should be in: enabled(1) - Attempt to activate the test as defined by this fsLinkQosCtlEntry. disabled(2) -… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.1.1.6 | ColumnfsLinkQosCtlRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2 | TablefsLinkQosResultsTable | not-accessible | current | The results of these operations are stored in the fsLinkQosResultsTable. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1 | RowfsLinkQosResultsEntry | not-accessible | current | Defines an entry in the fsLinkQosResultsTable. The fsLinkQosResultsTable has the same indexing as the fsLinkQosCtlTable so that a fsLinkQosResultsEntry corresp… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1.1 | ColumnfsLinkQosResultsOperStatus | read-only | current | Reflects the operational state of a fsLinkQosCtlEntry: enabled(1) - Test is active. disabled(2) - Test has stopped. completed(3) - Test is completed. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1.2 | ColumnfsLinkQosResultsIpTargetAddressType | read-only | current | This object indicates the type of address stored in the corresponding fsLinkQosResultsIpTargetAddress object. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1.3 | ColumnfsLinkQosResultsIpTargetAddress | read-only | current | This object reports the IP address associated with a fsLinkQosCtlTargetAddress value when the destination address is specified as a DNS name. The value of this… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1.4 | ColumnfsLinkQosResultsMaxRtt | read-only | current | The maximum packet round-trip-time (RTT) that received. A value of 0 for this object implies that no RTT has been received. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1.5 | ColumnfsLinkQosResultsMinRtt | read-only | current | The minimum packet round-trip-time (RTT) that received. A value of 0 for this object implies that no RTT has been received. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1.6 | ColumnfsLinkQosResultsAverageRtt | read-only | current | The current average packet round-trip-time (RTT). |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1.7 | ColumnfsLinkQosResultsDelayJitter | read-only | current | This object contains the sum of the squares for all ping responses received. Its purpose is to enable standard deviation calculation. The estimate value of the… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1.8 | ColumnfsLinkQosResultsPktsLossRate | read-only | current | The packets loss rate of the link. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1.9 | ColumnfsLinkQosResultsNetworkAF | read-only | current | The network availability factor. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3 | NodefsIfDeviceTrafficStatistics | |||
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1 | TablefsIfDeviceTrafficTable | not-accessible | current | A table of device traffic statistics. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1 | RowfsIfDeviceTrafficEntry | not-accessible | current | Device traffic statistics entry |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.1 | ColumnfsIfDeviceTrafficIndex | read-only | current | The device traffic interface index. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.2 | ColumnfsIfFC | read-only | current | |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.3 | ColumnfsIfFCTransRate | read-only | current | The transmission rate of the FC. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.4 | ColumnfsIfFCTransPktsNum | read-only | current | The transmission packets number of the FC. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.5 | ColumnfsIfFCDiscardRate | read-only | current | The discard rate of the FC. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.6 | ColumnfsIfFCDiscardPktsNum | read-only | current | The discard packets number of the FC. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.7 | ColumnfsIfFCPktsLossRate | read-only | current | The packets loss rate of the FC. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.8 | ColumnfsIfFCBandwidthRate | read-only | current | The bandwidth rate of the FC. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.9 | ColumnfsIfFCBandwidthPercentage | read-only | current | The bandwidth percentage of the FC. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.10 | ColumnfsIfDeviceFCGathers | read-only | current | Gathers of the device FC. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.11 | ColumnfsIfFullMeshFCGathers | read-only | current | Gathers of the whole network FC. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.12 | ColumnfsIfClassBasedGathers | read-only | current | Class-based Gathers. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.13 | ColumnfsIfNodeBasedGathers | read-only | current | Node-based Gathers. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.14 | ColumnfsIfNodeClassBasedGathers | read-only | current | Node&class-based Gathers. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.15 | ColumnfsIfNodeFCBasedGathers | read-only | current | Node&FC-based Gathers. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.16 | ColumnfsIfNodeDeviceFCBasedGathers | read-only | current | Node&device&FC-based Gathers. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.16 | TablefsIfPhyTable | not-accessible | current | list of physical interface basic configuration objects. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.16.1 | RowfsIfPhyEntry | not-accessible | current | Entry contains physical interface basic configurations. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.16.1.1 | ColumnfsIfPhyIndex | read-only | current | Physical port index. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.16.1.2 | ColumnfsifPhyOperStatus | read-only | current | The current operational state of the physical interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.17 | TablefsIfPeakRateTable | not-accessible | current | list of interface peak rate information objects. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.17.1 | RowfsIfPeakRateEntry | not-accessible | current | Entry contains interface peak rate information. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.17.1.1 | ColumnfsIfPeakRateIndex | read-only | current | interface index. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.17.1.2 | ColumnfsIfRxPeakRate | read-only | current | The transmission peak rate of interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.17.1.3 | ColumnfsIfRxPeakRateTime | read-only | current | The occuring time of transmission peak rate of interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.17.1.4 | ColumnfsIfTxPeakRate | read-only | current | The receiving peak rate of interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.17.1.5 | ColumnfsIfTxPeakRateTime | read-only | current | The occuring time of receiving peak rate of interface. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.18 | TablefsApInfoTable | not-accessible | current | list of ap information objects. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.18.1 | RowfsApInfoEntry | not-accessible | current | Entry contains ap information. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.18.1.1 | ColumnfsApInfoAddress | read-only | current | The ap's address at its protocol sub-layer. The ap's media-specific MIB must define the bit and byte ordering and the format of the value of this object. For i… |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.18.1.2 | ColumnfsApInfoWireInRate | read-only | current | The input rate in bps of all ap wire-ports. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.18.1.3 | ColumnfsApInfoWireOutRate | read-only | current | The output rate in bps of all ap wire-ports. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.18.1.4 | ColumnfsApInfoWireInOctets | read-only | current | The total number of octets received on the ap wire-ports. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.18.1.5 | ColumnfsApInfoWireOutOctets | read-only | current | The total number of octets transmitted out of the ap wire-ports. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.19 | TablefsIfDropTable | not-accessible | current | A table of interface drop statistics. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.19.1 | RowfsIfDropEntry | not-accessible | current | Interface statistics drop entry |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.19.1.1 | ColumnfsIfDropIndex | read-only | current | The device traffic drop interface index. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.19.1.2 | ColumnfsIfInDropPkts | read-only | current | Input discarded packets without drop by QOS. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.19.1.3 | ColumnfsIfInResLackPkts | read-only | current | Input discarded packets by resources lack. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.19.1.4 | ColumnfsIfInQosDropPkts | read-only | current | Discarded packets by QOS. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.19.1.5 | ColumnfsIfFwdEntryDropPkts | read-only | current | Input discarded packets by forwardind entry. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.19.1.6 | ColumnfsIfOutDropPkts | read-only | current | Output discarded packets. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.19.1.7 | ColumnfsIfOutResLackPkts | read-only | current | Output discarded packets by resources lack. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.19.1.8 | ColumnfsIfNoBufferConut | read-only | current | discarded packets by no buffer. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.1.19.1.9 | ColumnfsIfOBMDropPkts | read-only | current | OBM discarded packets. |
| 1.3.6.1.4.1.52642.1.1.10.2.10.2 | NodefsInterfaceTraps | |||
| 1.3.6.1.4.1.52642.1.1.10.2.10.2.1 | ScalarlineDetectStatus | accessible-for-notify | current | The type of storm of interface |
| 1.3.6.1.4.1.52642.1.1.10.2.10.2.2 | ScalarlineDetectPosition | accessible-for-notify | current | Location where the break or short circuit in the line happens (Distance from the switch port, in metre.) |
| 1.3.6.1.4.1.52642.1.1.10.2.10.2.3 | NotificationlineQualityDetect | current | The notification of discovering a break or short circuit in the line, or restoring the line to the normal state. | |
| 1.3.6.1.4.1.52642.1.1.10.2.10.3 | NodefsInterfaceMIBConformance | |||
| 1.3.6.1.4.1.52642.1.1.10.2.10.3.1 | NodefsInterfaceMIBCompliances | |||
| 1.3.6.1.4.1.52642.1.1.10.2.10.3.1.1 | CompliancefsInterfaceMIBCompliance | current | The compliance statement for entities which implement the FS Interface MIB | |
| 1.3.6.1.4.1.52642.1.1.10.2.10.3.2 | NodefsInterfaceMIBGroups | |||
| 1.3.6.1.4.1.52642.1.1.10.2.10.3.2.1 | GroupfsInterfaceMIBGroup | current | A collection of objects providing interface basic configure . | |
| 1.3.6.1.4.1.52642.1.1.10.2.10.3.2.2 | GroupfsPortTypeChooseMibGroup | current | Information collection of choosing port type. | |
| 1.3.6.1.4.1.52642.1.1.10.2.10.3.2.3 | GroupfsIfMTUMibGroup | current | Interface MTU information collection. | |
| 1.3.6.1.4.1.52642.1.1.10.2.10.3.2.4 | GroupfsIfLineDetectGroup | current | Information collection of line quality detection. | |
| 1.3.6.1.4.1.52642.1.1.10.2.10.3.2.5 | GroupfsIfAvailableBWMibGroup | current | Interface available bandwidth information collection. |