G3-PLC-MIB
221 objects
The MIB module for managing the MAC and 6LowPAN adaptation layer of the G3-PLC network interfaces of a device.
Imported Objects
| IF-MIB | ifIndex |
| INET-ADDRESS-MIB | InetAddressIPv6 InetAddressPrefixLength |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 enterprises Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DateAndTime RowStatus TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.20998 | Nodehoneywell | |||
| 1.3.6.1.4.1.20998.2 | Nodeacs | |||
| 1.3.6.1.4.1.20998.2.1 | Nodeees | |||
| 1.3.6.1.4.1.20998.2.1.1 | Nodeserg | |||
| 1.3.6.1.4.1.20998.2.1.1.1.2.0.1280 | Notificationg3PlcEventDeviceTypeAssigned | current | An event indicating a device type was assigned to a particular meter. | |
| 1.3.6.1.4.1.20998.2.1.1.3 | Identityg3PlcOfdmMib | The MIB module for managing the MAC and 6LowPAN adaptation layer of the G3-PLC network interfaces of a device. | ||
| 1.3.6.1.4.1.20998.2.1.1.3.1 | Nodeg3PlcMacParam | |||
| 1.3.6.1.4.1.20998.2.1.1.3.1.1 | Tableg3PlcMacTable | not-accessible | current | This table holds the MAC layer parameters and statistics for every PLC interface available on the system. These include the IEEE 802.15.4 MAC sublayer attribut… |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1 | Rowg3PlcMacIfaceEntry | not-accessible | current | MAC objects for a particular PLC interface. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.64 | Columng3PlcMacAckWaitDuration | read-only | current | Duration of acknowledgement in microseconds. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.71 | Columng3PlcMacMaxBe | read-write | current | Maximum value of back-off exponent (BE) in the CSMA-CA algorithm. It should always be greater than g3PlcMacMinBe. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.73 | Columng3PlcMacBsn | read-only | current | Frame sequence number added to the outgoing beacon MAC command frame. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.76 | Columng3PlcMacDsn | read-only | current | Data or command frame sequence number added to outgoing frames. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.78 | Columng3PlcMacMaxCsmaBackoffs | read-write | current | Maximum number of back-off attempts in the CSMA-CA algorithm before returning a channel access failure. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.79 | Columng3PlcMacMinBe | read-write | current | Minimum value of back-off exponent (BE) in the CSMA-CA algorithm. This value must be less than plcG3MacMaxBe. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.80 | Columng3PlcMacPanId | read-write | current | PAN identifier of the network on which this interface is operating. If set to 0xFFFF, the interface has currently not joined any networks. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.81 | Columng3PlcMacPromiscuousMode | read-write | current | Promiscuous mode enabled. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.83 | Columng3PlcMacShortAddress | read-only | current | Short address assigned to this interface (unique within the PAN). |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.89 | Columng3PlcMacMaxFrameRetries | read-write | current | Maximum number of retransmission after a transmission failure. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.92 | Columng3PlcMacTimeStampSupported | read-only | current | MAC frame time stamp support enable. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.93 | Columng3PlcMacSecurityEnabled | read-write | current | Inidication of whether th MAC layer security is enabled. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.119 | Columng3PlcMacFrameCounter | read-only | current | The outgoing frame counter for this interface. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.256 | Columng3PlcMacHighPriorityWindowSize | read-write | current | The high priority contention window size in number of slots. Default value is 7 times g3PlcASlotTime. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.257 | Columng3PlcMacTxDataPacketCount | read-only | current | Statistic counter of successfully transmitted unicast MSDUs. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.258 | Columng3PlcMacRxDataPacketCount | read-only | current | Statistic counter of successfully received unicast MSDUs. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.259 | Columng3PlcMacTxCmdPacketCount | read-only | current | Statistic counter of successfully transmitted command packets. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.260 | Columng3PlcMacRxCmdPacketCount | read-only | current | Statistic counter of successfully received command packets. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.261 | Columng3PlcMacCsmaFailCount | read-only | current | Counts the number of times the CSMA back-offs reach g3PlcMacMaxCsmaBackoffs. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.262 | Columng3PlcMacCsmaNoAckCount | read-only | current | Counts the number of times an ACK is not received while transmitting a unicast data frame (The loss of ACK is attributed to collisions). |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.263 | Columng3PlcMacRxDataBroadcastCount | read-only | current | Statistic counter of successfully received broadcast frames. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.264 | Columng3PlcMacTxDataBroadcastCount | read-only | current | Statistic counter of the number of broadcast frames sent. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.265 | Columng3PlcMacBadCrcCount | read-only | current | Statistic counter of the number of frames received with bad CRC. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.267 | Columng3PlcMacFreqNotching | read-write | current | S-FSK 63 and 74 kHz frequency notching. See clause B.3 of ITU-T G.9901. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.268 | Columng3PlcMacCsmaFairnessLimit | read-write | current | Channel access fairness limit. Specifies how many failed back-off attempts, back-off exponent is set to g3PlcMinBe. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.269 | Columng3PlcMacTmrTtl | read-write | current | Maximum time to live for an entry in the neighbour table. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.270 | Columng3PlcMacPosTableEntryTtl | read-write | current | Maximum time to live for an entry in the personal operating space table. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.271 | Columng3PlcMacRcCoord | read-only | current | Route cost to coordinator to be used in the beacon payload as RC_COORD. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.272 | Columng3PlcMacToneMask | read-write | current | Defines the tone mask to use during symbol formation. - 0x000000000FFFFFFFFF for CENELEC-A bandplan - 0xFFFFFFFFFFFFFFFFFF for the FCC bandplan. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.273 | Columng3PlcMacBeaconRandomizationWindowLength | read-write | current | Duration time in seconds for beacon randomization. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.274 | Columng3PlcMacA | read-write | current | This parameter controls the adaptive CW linear decrease. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.275 | Columng3PlcMacK | read-write | current | Rate adaptation factor for channel access fairness limit. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.276 | Columng3PlcMacMinCwAttempts | read-write | current | Number of consecutive attempts while using minimum CW. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.277 | Columng3PlcMacCenelecLegacyMode | read-only | current | This read only attribute indicates the capability of the PLC node: (0) The following configuration is used: - Elementary interleaving - Interleaver parameters … |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.278 | Columng3PlcMacFccLegacyMode | read-only | current | This read-only attribute indicates the capability of the PLC node: (0) The following configuration is used: - Differential FCH modulation - Elementary interlea… |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.286 | Columng3PlcMacBroadcastMaxCwEnabled | read-write | current | If enabled, MAC uses maximum contention window as specified in clause 9.3.1.3 of ITU-T G.9903. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.287 | Columng3PlcMacTransmitAttenuation | read-write | current | Attenuation of the output level in dB. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.1162629889 | Columng3PlcMacInterfaceEnabled | read-write | current | Enable or disable the MAC/PHY layers of the G3-PLC interface. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.1162629890 | Columng3PlcMacUseFixedGmk | read-write | current | Disable automatic changing and renewal of the GMK key used on the PAN. Set to true in order to allow sniffing on the network. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.1162629891 | Columng3PlcMacCoherentEnabled | read-write | current | Indicates whether the device operates in coherent or non-coherent mode. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.1.1.1162629892 | Columng3PlcMacBandPlan | read-write | current | Indicates the band plan on which the modem operates. Changing this values requires restarting the device, and may be restricted to the subset supported by the … |
| 1.3.6.1.4.1.20998.2.1.1.3.1.2 | Tableg3PlcMacKeys | not-accessible | current | This attribute holds GMK keys required for MAC layer ciphering. The attribute can hold two 16-byte keys. The row index corresponds to the key identifier value.… |
| 1.3.6.1.4.1.20998.2.1.1.3.1.2.1 | Rowg3PlcMacKeyEntry | not-accessible | current | Key slot. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.2.1.1 | Columng3PlcMacKeyIndex | not-accessible | current | The key identifier used to refer to this encryption key. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.2.1.2 | Columng3PlcMacKeyVal | read-write | current | The AES-128 key that is used for ciphering the frames exchanged at the MAC layer. This value return an empty octet-string when read for security reasons. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.3 | Tableg3PlcMacNeighbourTable | not-accessible | current | The neighbour table contains information about all the devices within the POS of the device. One element of the table represents one PLC direct neighbour of th… |
| 1.3.6.1.4.1.20998.2.1.1.3.1.3.1 | Rowg3PlcMacNeighbourTableEntry | not-accessible | current | Represents a neighbouring node. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.3.1.1 | Columng3PlcMacNeighbourShortAddress | not-accessible | current | The MAC Short Address of the node which this entry refers to. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.3.1.2 | Columng3PlcMacNeighbourPanId | read-only | current | The PAN identifier of the neighbour. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.3.1.3 | Columng3PlcMacNeighbourDeviceType | read-only | current | The device type of a neighbour entry: (1) PAN coordinator (base node) (2) service node which can act as intermediary node (3) service node which can only act a… |
| 1.3.6.1.4.1.20998.2.1.1.3.1.3.1.4 | Columng3PlcMacNeighbourIsParent | read-only | current | Indicates whether the neighbour is a topological parent of this device. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.3.1.5 | Columng3PlcMacNeighbourPayloadModulation | read-only | current | Payload Modulation scheme to be used when transmitting to this neighbour. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.3.1.6 | Columng3PlcMacNeighbourToneMap | read-only | current | The Tone Map parameter defines which frequency sub-band can be used for communication with the neighbour. A bit set to 1 means that the frequency sub-band can … |
| 1.3.6.1.4.1.20998.2.1.1.3.1.3.1.7 | Columng3PlcMacNeighbourModulation | read-only | current | The modulation type to use for communicating with the neighbour: (0) Robust mode (1) DBPSK or BPSK (2) DQPSK or QPSK (3) D8PSK or 8-PSK (4) 16-QAM |
| 1.3.6.1.4.1.20998.2.1.1.3.1.3.1.8 | Columng3PlcMacNeighbourTxGain | read-only | current | Defines the Tx Gain to use to transmit frames to the neighbour. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.3.1.9 | Columng3PlcMacNeighbourTxRes | read-only | current | Defines the Tx Gain resolution corresponding to one gain step. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.3.1.10 | Columng3PlcMacNeighbourTxCoeff | read-only | current | A parameter that specifies transmitter gain for each group of tones represented by one valid bit of the tone map. The receiver measures the frequency-dependent… |
| 1.3.6.1.4.1.20998.2.1.1.3.1.3.1.11 | Columng3PlcMacNeighbourReverseLqi | read-only | current | Link Quality Indicator of the link to the neighbour (reverse LQI). |
| 1.3.6.1.4.1.20998.2.1.1.3.1.3.1.12 | Columng3PlcMacNeighbourPhaseDifferential | read-only | current | Phase difference in multiples of 60 degrees between the mains phase of the local node and the neighbour node. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.3.1.13 | Columng3PlcMacNeighbourTmrValidTime | read-only | current | Remaining time in minutes until which the tone map response parameters in the neighbour table are considered valid. - When the entry is created, this value sha… |
| 1.3.6.1.4.1.20998.2.1.1.3.1.4 | Tableg3PlcMacPosTable | not-accessible | current | Each time a message is received (filtered according to IEEE 802.15.4 clause 7.5.6.2), an entry in the Personal Operating Space table is created or updated (if … |
| 1.3.6.1.4.1.20998.2.1.1.3.1.4.1 | Rowg3PlcMacPosTableEntry | not-accessible | current | Represents a potential destination within the personal operating space. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.4.1.1 | Columng3PlcMacPosShortAddress | not-accessible | current | The MAC short address of the neighbour which this entry refers to. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.4.1.2 | Columng3PlcMacPosLqi | read-only | current | Link quality indicator of the last received packet from this neighbour. |
| 1.3.6.1.4.1.20998.2.1.1.3.1.4.1.3 | Columng3PlcMacPosValidTime | read-only | current | Remaining time in minutes until when this entry is considered valid. Every time an entry is created, it is set to g3PlcMacPosTableEntryTTL. When it reaches zer… |
| 1.3.6.1.4.1.20998.2.1.1.3.2 | Nodeg3PlcAdpParam | |||
| 1.3.6.1.4.1.20998.2.1.1.3.2.1 | Tableg3PlcAdpTable | not-accessible | current | Adaptation layer parameters and statistics for every PLC interface available on the system. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1 | Rowg3PlcAdpIfaceEntry | not-accessible | current | 6LowPAN adaptation layer parameters and statistics for a given G3-PLC interface. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.1 | Columng3PlcAdpSecurityLevel | read-write | current | The minimum security level to be used for incoming and outgoing adaptation frames. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.2 | Columng3PlcAdpBroadcastLogEntryTtl | read-write | current | Maximum time to live of an g3PlcAdpBroadcastLogTable entry. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.3 | Columng3PlcAdpMetricType | read-only | current | Metric type to be used for routing purposes. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.4 | Columng3PlcAdpLowLqiValue | read-write | current | The low LQI value defines the LQI value, used in metric computation, below which a link to a neighbour is considered as an unreliable link. This value shall be… |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.5 | Columng3PlcAdpHighLqiValue | read-write | current | The high LQI value defines the LQI value, used in metric computation, above which a link to a neighbour is considered as a reliable link. This value is greater… |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.6 | Columng3PlcAdpRrepWait | read-write | current | An RREP shall be generated after a delay of g3PlcAdpRREPWait seconds after either the arrival of the first RREQ or the transmission of the latest RREP. g3PlcAd… |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.8 | Columng3PlcAdpCoordShortAddress | read-write | current | Defines the short address of the coordinator. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.9 | Columng3PlcAdpRlcEnabled | read-write | current | Enables the sending of RLCREQ frame by the device. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.10 | Columng3PlcAdpAddRevLinkCost | read-write | current | It represents an additional cost to take into account a possible asymmetry in the link. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.13 | Columng3PlcAdpUnicastRreqGenEnabled | read-write | current | If true, the RREQ shall be generated with its ``unicast RREQ'' flag set to `1'. If false, the RREQ shall be generated with its ``unicast RREQ'' flag set to `0'. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.15 | Columng3PlcAdpMaxHops | read-write | current | Defines the maximum number of hops to be used by the routing algorithm. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.16 | Columng3PlcAdpDeviceType | read-write | current | Defines the type of device connected to the modem: (0) PAN device (1) PAN coordinator (2) Not defined |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.17 | Columng3PlcAdpNetTraversalTime | read-write | current | Maximum time that a packet is expected to take to reach any node from any node. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.18 | Columng3PlcAdpRoutingTableEntryTtl | read-write | current | Maximum time-to-live of a routing table entry. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.19 | Columng3PlcAdpKr | read-write | current | A weight factor for robust mode to calculate link cost. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.20 | Columng3PlcAdpKm | read-write | current | A weight factor for modulation to calculate link cost. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.21 | Columng3PlcAdpKc | read-write | current | A weight factor for number of active tones to calculate link cost. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.22 | Columng3PlcAdpKq | read-write | current | A weight factor for LQI to calculate route cost. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.23 | Columng3PlcAdpKh | read-write | current | A weight factor for hop to calculate link cost. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.24 | Columng3PlcAdpRreqRetries | read-write | current | The number of RREQ retransmission in case of RREP reception time out. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.25 | Columng3PlcAdpRreqWait | read-write | current | Time in seconds to wait between two consecutive RREQ or RLCREQ generations. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.26 | Columng3PlcAdpWeakLqiValue | read-write | current | The weak link value defines the LQI value below which a link to a neighbour is considered as a weak link. A value of 52 represents an SNR of 3 dB. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.27 | Columng3PlcAdpKrt | read-write | current | A weight factor for the number of active routes in the routing table to calculate link cost. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.28 | Columng3PlcAdpSoftVersion | read-only | current | The software version of the firmware running on the G3-PLC BSP. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.29 | Columng3PlcAdpSnifferMode | read-write | current | Sniffer mode activation/deactivation. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.31 | Columng3PlcAdpBlacklistTableEntryTtl | read-write | current | Maximum time-to-live of a blacklisted neighbour entry. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.32 | Columng3PlcAdpMaxJoinWaitTime | read-write | current | Network join timeout in seconds for LBD. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.33 | Columng3PlcAdpPathDiscoveryTime | read-write | current | Timeout for path discovery in seconds. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.34 | Columng3PlcAdpActiveKeyIndex | read-only | current | Index of the active GMK to be used for data transmission. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.36 | Columng3PlcAdpDefaultCoordRouteEnabled | read-write | current | If true, the adaptation layer adds a default route to the coordinator after successful completion of the bootstrapping procedure. If false no default route wil… |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.240 | Columng3PlcAdpDisableDefaultRouting | read-write | current | If true, the default routing (LOADng) is disabled. If false, the default routing (LOADng) is enabled. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.1162629889 | Columng3PlcAdpAverageHops | read-only | current | Contains the average amount of hops required to reach a node in the PAN. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.1.1.1162629890 | Columng3PlcAdpAverageRtt | read-only | current | Contains the average round trip time in seconds to reach a node in the PAN. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.2 | Tableg3PlcAdpPrefixTable | not-accessible | current | Contains the list of prefixes defined on this PAN. Note that it is assumed that the link local IPv6 address exists independently and is not affected by the pre… |
| 1.3.6.1.4.1.20998.2.1.1.3.2.2.1 | Rowg3PlcAdpPrefixEntry | not-accessible | current | IPv6 prefix entry. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.2.1.1 | Columng3PlcAdpPrefix | not-accessible | current | IPv6 address or a prefix of an IPv6 address. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.2.1.2 | Columng3PlcAdpPrefixLength | not-accessible | current | Number of leading bits in the prefix that are valid. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.2.1.3 | Columng3PlcAdpPrefixOnLink | read-only | current | Indicates if prefix is on link. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.2.1.4 | Columng3PlcAdpPrefixAutonomous | read-only | current | Indicates if prefix can be used for autonomous address configuration. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.2.1.5 | Columng3PlcAdpPrefixValidLifetime | read-only | current | Length of time during which addresses generated from this prefix remain valid for the purpose of on-link determination. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.2.1.6 | Columng3PlcAdpPrefixPrefLifetime | read-only | current | Length of time during which addresses generated from this prefix remain preferred. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.2.1.7 | Columng3PlcAdpPrefixStatus | read-create | current | Prefix entry status. Set to `destroy' to remove the prefix. Set to `createAndGo' when creating a new instance. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.3 | Tableg3PlcAdpContextInfoTable | not-accessible | current | Contains the context information associated to each CID extension field. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.3.1 | Rowg3PlcAdpContextInfoEntry | not-accessible | current | Context info entry. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.3.1.1 | Columng3PlcAdpContextId | not-accessible | current | Corresponds to the 4-bit context information used for source and destination address (SCI, DCI). |
| 1.3.6.1.4.1.20998.2.1.1.3.2.3.1.2 | Columng3PlcAdpContextLength | read-only | current | Indicates the length of the carried context. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.3.1.3 | Columng3PlcAdpContext | read-only | current | Corresponds to the carried context used for compression/decompression purposes. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.3.1.4 | Columng3PlcAdpContextCompression | read-only | current | Indicates if context is valid for use in compression. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.3.1.5 | Columng3PlcAdpContextValidLifeTime | read-only | current | Remaining time during which the context information table is valid. It is updated upon receipt of the advertised context. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.3.1.6 | Columng3PlcAdpContextStatus | read-create | current | Context entry status. Set to `destroy' to remove the compression context. Set to `createAndGo' when creating a new instance. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.4 | Tableg3PlcAdpRoutingTable | not-accessible | current | Contains the 6LowPAN routing table. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.4.1 | Rowg3PlcAdpRoutingEntry | not-accessible | current | Routing entry for a destination node on the PAN. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.4.1.1 | Columng3PlcAdpRoutingDestination | read-only | current | Short identifier of the destination of the routing entry. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.4.1.2 | Columng3PlcAdpRoutingNextHop | read-only | current | Short identifier of the next hop in the route towards the destination. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.4.1.3 | Columng3PlcAdpRoutingCost | read-only | current | Cumulative link cost along the route towards the destination. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.4.1.4 | Columng3PlcAdpRoutingHopCount | read-only | current | Number of hops in the selected route to the destination. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.4.1.5 | Columng3PlcAdpRoutingWeakLinkCost | read-only | current | Number of weak links to the destination. This number cannot exceed g3PlcAdpMaxHops. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.4.1.6 | Columng3PlcAdpRoutingValidTime | read-only | current | Remaining time until when this entry in the routing table is considered invalid. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.5 | Tableg3PlcAdpBroadcastLogTable | not-accessible | current | Contains the broadcast log table. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.5.1 | Rowg3PlcAdpBroadcastLogEntry | not-accessible | current | Entry describing a recently received broadcast packet. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.5.1.1 | Columng3PlcAdpBroadcastLogSource | read-only | current | Short identifier of the source of the broadcast packet. This is the address of the broadcast initiator. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.5.1.2 | Columng3PlcAdpBroadcastLogSeqNum | read-only | current | The sequence number contained in the BC0 header. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.5.1.3 | Columng3PlcAdpBroadcastLogValidTime | read-only | current | Remaining time until when this entry in the broadcast log table is considered invalid. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.6 | Tableg3PlcAdpBlacklistTable | not-accessible | current | Contains the list of the blacklisted neighbours. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.6.1 | Rowg3PlcAdpBlackListEntry | not-accessible | current | Blacklisted node. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.6.1.1 | Columng3PlcAdpBlacklistEntryAddress | not-accessible | current | The short identifier of the blacklisted neighbour. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.6.1.2 | Columng3PlcAdpBlacklistEntryValidTime | read-only | current | Remaining time in minutes until when this entry in the blacklist neighbour table is considered invalid. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.7 | Tableg3PlcAdpDestinationAddressTable | not-accessible | current | Contains the list of the addresses of the device for which this LOADng router is providing connectivity. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.7.1 | Rowg3PlcAdpDestinationAddressEntry | not-accessible | current | Destination address entry. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.7.1.1 | Columng3PlcAdpDestinationAddress | read-only | current | IPv6 address entry. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.7.1.2 | Columng3PlcAdpDestinationAddressStatus | read-create | current | Status of the address entry. Set to `destroy' to remove the address from the host. Set to `createAndGo' to add a new entry. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.8 | Tableg3PlcAdpGroupTable | not-accessible | current | Contains the group addresses to which the device belongs. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.8.1 | Rowg3PlcAdpGroupEntry | not-accessible | current | Group address entry |
| 1.3.6.1.4.1.20998.2.1.1.3.2.8.1.1 | Columng3PlcAdpGroupAddress | read-only | current | Short identifier group address. |
| 1.3.6.1.4.1.20998.2.1.1.3.2.8.1.2 | Columng3PlcAdpGroupStatus | read-create | current | Status of the group address. Set to `destroy' to remove entry from table. Set to `createAndGo' to add new entry to the table. |
| 1.3.6.1.4.1.20998.2.1.1.3.3 | Nodeg3PlcPanCoordination | |||
| 1.3.6.1.4.1.20998.2.1.1.3.3.1 | Tableg3PlcJoinStats | not-accessible | current | Statistics on the PLC join process for each PLC interface. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.1.1 | Rowg3PlcJoinStatsEntry | not-accessible | current | Statistics on the PLC join process for a given PLC interface. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.1.1.1 | Columng3PlcLastJoinRequest | read-only | current | Timestamp of the last incoming join request. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.1.1.2 | Columng3PlcJoinRequestCounter | read-only | current | Holds the total amount of join requests serviced on this interface. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.2 | Tableg3PlcJoinRequestTable | not-accessible | current | Table holding outstanding join requests to be serviced by this PAN coordinator. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.2.1 | Rowg3PlcJoinRequestEntry | not-accessible | current | Outstanding join request for a node on the network. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.2.1.1 | Columng3PlcJoinEntrySourceAddress | not-accessible | current | EUI-64 of the service node trying to join the PAN. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.2.1.2 | Columng3PlcJoinEntryShortIdentifier | read-only | current | The desired short identifier for this joining node. If set to 0xFFFF, a value will be picked by the PAN coordinator. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.2.1.3 | Columng3PlcJoinEntryPsk | read-only | current | Holds the pre-shared key associated with the source node. This key is to be used during the EAP handshake. Reading this value returns an empty octet-string for… |
| 1.3.6.1.4.1.20998.2.1.1.3.3.2.1.4 | Columng3PlcJoinEntryPreliminaryTask | read-only | current | Identifier of communication task to be executed on the source node after completing the join process. This task can be used for performing an initial clock syn… |
| 1.3.6.1.4.1.20998.2.1.1.3.3.2.1.5 | Columng3PlcJoinEntryCreationTime | read-only | current | Holds the date/time at which the join request was created. Set to epoch if not tracked. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.2.1.6 | Columng3PlcJoinEntryStatus | read-create | current | Holds the status of the row. When set to `destroy', the join request is declined and the entry is removed. Creating new entries is not possible. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.3 | Tableg3PlcJoinBlackListTable | not-accessible | current | This table holds all service nodes which have been banned from joining the network. Adding nodes to this table can be used to force a node on the edge of two n… |
| 1.3.6.1.4.1.20998.2.1.1.3.3.3.1 | Rowg3PlcJoinBlackListEntry | not-accessible | current | A service node which has been banned from joining the network. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.3.1.1 | Columng3PlcJoinBlackListNodeIdentifier | not-accessible | current | The MAC address of the blacklisted node. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.3.1.2 | Columng3PlcJoinBlackListEntryStartDate | read-only | current | Holds the date at which the entry becomes active. Set to epoch if unknown. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.3.1.3 | Columng3PlcJoinBlackListEntryStopDate | read-only | current | Holds the date at which the entry is no longer active. Set to maximum if unknown. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.3.1.4 | Columng3PlcJoinBlackListNodeStatus | read-create | current | The status of a blacklist entry. Creating a new blacklist entry is possible by writing the EUI64 address and setting the row status to createAndGo. Removing a … |
| 1.3.6.1.4.1.20998.2.1.1.3.3.4 | Tableg3PlcKeepAliveTable | not-accessible | current | Keep-alive background service. Periodically pings meters to keep routing table up to date. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.4.1 | Rowg3PlcKeepAliveEntry | not-accessible | current | Keep-alive settings for a G3-PLC interface. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.4.1.1 | Columng3PlcKeepAliveEnabled | read-write | current | Holds the state of the keep-alive background service. If set to true, the background service will be enabled. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.4.1.2 | Columng3PlcKeepAliveScheduleInterval | read-write | current | The delay between consecutive runs of the keep-alive service. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.4.1.3 | Columng3PlcKeepAlivePingInterval | read-write | current | The delay between two consecutive pings. Increasing this value avoids large peaks of route requests on the network when the keep-alive service is invoked. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.4.1.4 | Columng3PlcKeepAliveMinInactiveTime | read-write | current | Holds the minimum time of service node inactivity before considering a node eligible for the keep-alive service. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.4.1.5 | Columng3PlcKeepAliveMaxInactiveTime | read-write | current | Holds the maximum time of service node inactivity before no longer considering a node eligible for the keep-alive service. |
| 1.3.6.1.4.1.20998.2.1.1.3.3.4.1.6 | Columng3PlcKeepAliveFailCount | read-write | current | Holds the maximum of consecutive ping failures allowed before changing a node's state. |
| 1.3.6.1.4.1.20998.2.1.1.3.4 | Nodeg3PlcEvents | |||
| 1.3.6.1.4.1.20998.2.1.1.3.4.0 | Nodeg3PlcEventDef | |||
| 1.3.6.1.4.1.20998.2.1.1.3.4.0.1 | Notificationg3PlcStackEvent | current | This notification can be used for generic G3-PLC related events. The event object should contain a human-readable description of the event. | |
| 1.3.6.1.4.1.20998.2.1.1.3.4.0.2 | Notificationg3PlcRegisterNodeEvent | current | This notification can be generated when a new node has joined the network. The notification objects may include the service access points on which this node ca… | |
| 1.3.6.1.4.1.20998.2.1.1.3.4.0.3 | Notificationg3PlcUnregisterNodeEvent | current | This notification can be generated when a new node has left the network. | |
| 1.3.6.1.4.1.20998.2.1.1.3.4.0.4 | Notificationg3PlcJoinRequestEvent | current | This notification can be generated when a new node is attempting to join the network. | |
| 1.3.6.1.4.1.20998.2.1.1.3.4.0.5 | Notificationg3PlcJoinFailureEvent | current | This notification can be generated when a new node which was earlier attempting to join the network has failed to complete its EAP handshake process successful… | |
| 1.3.6.1.4.1.20998.2.1.1.3.4.0.6 | Notificationg3PlcBlackListEvent | current | This notification can be generated when a node has been added or removed from the blacklist. | |
| 1.3.6.1.4.1.20998.2.1.1.3.4.0.7 | Notificationg3PlcNodeLostEvent | current | This notification can be generated when a node which was reachable on the PAN earlier is now no longer reachable. | |
| 1.3.6.1.4.1.20998.2.1.1.3.4.0.8 | Notificationg3PlcNodeRecoveredEvent | current | This notification can be generated when a node which had vanished from the network earlier is now reachable again. | |
| 1.3.6.1.4.1.20998.2.1.1.3.4.0.9 | Notificationg3PlcPanIdEvent | current | This notification can be generated when one or more conflicting PANs were detected by the device, or when the PAN was changed. The notification objects may inc… | |
| 1.3.6.1.4.1.20998.2.1.1.3.4.0.10 | Notificationg3PlcTopologyUpdateEvent | current | This notification can be generated when one or more paths between the base node and a service node was detected. The notification objects include the affected … | |
| 1.3.6.1.4.1.20998.2.1.1.3.4.1 | Nodeg3PlcEventArg | |||
| 1.3.6.1.4.1.20998.2.1.1.3.4.1.1 | Scalarg3PlcEventDescription | accessible-for-notify | current | Human-readable description of the event. |
| 1.3.6.1.4.1.20998.2.1.1.3.4.1.2 | Tableg3PlcEventNodeTable | not-accessible | current | G3-PLC node to which the event applies. |
| 1.3.6.1.4.1.20998.2.1.1.3.4.1.2.1 | Rowg3PlcEventNodeEntry | not-accessible | current | G3-PLC node entry included in notification object list. |
| 1.3.6.1.4.1.20998.2.1.1.3.4.1.2.1.1 | Columng3PlcEventNodeAddress | accessible-for-notify | current | EUI64 of the affected node. |
| 1.3.6.1.4.1.20998.2.1.1.3.4.1.2.1.2 | Columng3PlcEventNodeShortIdentifier | accessible-for-notify | current | Short identifier of the affected node. |
| 1.3.6.1.4.1.20998.2.1.1.3.4.1.2.1.3 | Columng3PlcEventNodeIp4Address | accessible-for-notify | current | This object holds the routable IPv4 address on which the node can be reached. If no such address is present, the field contains the zero address. |
| 1.3.6.1.4.1.20998.2.1.1.3.4.1.2.1.4 | Columng3PlcEventNodeIp6Address | accessible-for-notify | current | This object holds the routable IPv6 address on which the node can be reached. If no such address is present, the field contains the zero address. |
| 1.3.6.1.4.1.20998.2.1.1.3.4.1.2.1.5 | Columng3PlcEventNodeDLMSGateway | accessible-for-notify | current | This object holds the logical device ID of the DLMS/COSEM application layer gateway which provides access to the affected node. If no such gateway is present, … |
| 1.3.6.1.4.1.20998.2.1.1.3.4.1.2.1.6 | Columng3PlcEventNodeDLMSMirror | accessible-for-notify | current | This object holds the logical device ID of the DLMS/COSEM application layer mirror which provides access to the affected node's cached data. If no such mirror … |
| 1.3.6.1.4.1.20998.2.1.1.3.4.1.2.1.7 | Columng3PlcEventNodeForwardPath | accessible-for-notify | current | Forward path from the PAN coordinator to the the affected node. The path consists of a sequence of intermediate hops (short addresses), separated by whitespace… |
| 1.3.6.1.4.1.20998.2.1.1.3.4.1.2.1.8 | Columng3PlcEventNodeReversePath | accessible-for-notify | current | Reverse path from the the affected node to the PAN coordinator. The path consists of a sequence of intermediate hops (short addresses), separated by whitespace… |
| 1.3.6.1.4.1.20998.2.1.1.3.5 | Nodeg3PlcConf | |||
| 1.3.6.1.4.1.20998.2.1.1.3.5.1 | Nodeg3PlcGroups | |||
| 1.3.6.1.4.1.20998.2.1.1.3.5.1.1 | Groupg3PlcMacParamGroup | current | MAC related parameters and statistics. | |
| 1.3.6.1.4.1.20998.2.1.1.3.5.1.2 | Groupg3PlcAdpParamGroup | current | 6LowPAN adaptation layer parameters and statistics. | |
| 1.3.6.1.4.1.20998.2.1.1.3.5.1.3 | Groupg3PlcPanCoordinationGroup | current | PAN coordinator related objects. | |
| 1.3.6.1.4.1.20998.2.1.1.3.5.1.4 | Groupg3PlcEventGroup | current | G3-PLC related events. | |
| 1.3.6.1.4.1.20998.2.1.1.3.5.1.5 | Groupg3PlcEventArgGroup | current | Objects included in G3-PLC events. | |
| 1.3.6.1.4.1.20998.2.1.1.3.5.2 | Nodeg3PlcCompliances | |||
| 1.3.6.1.4.1.20998.2.1.1.3.5.2.1 | Complianceg3PlcServiceNodeCompliance | current | Module compliance for G3-PLC service nodes. | |
| 1.3.6.1.4.1.20998.2.1.1.3.5.2.2 | Complianceg3PlcBaseNodeCompliance | current | The event argument group is only required when one or more of the events defined in this MIB module is implemented. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| BandPlan | INTEGER { cenelecA(0), cenelecB(1), arib(2), fcc(3), ieee19012(4) } | current | Represents the band plan on which the G3-PLC transmission takes place. |
| EUI64 | OCTET STRING (SIZE (8)) | current | The IEEE defined 64-bit extended unique identifier (EUI-64) is a concatenation of the 24-bit company_id value by the IEEE Registration Authority and a 40-bit extension identifier assigned by the organization with that c… |
| PanIdentifier | Integer32 (0..65535) | current | A 16-bit PAN identifier |
| ShortIdentifier | Integer32 (0..65535) | current | A 16-bit identifier of a G3-PLC node, unique within a PAN. This address is used during 6LowPAN compression and routing. |
| ToneMap | OCTET STRING (SIZE (9)) | current | A 72-bit string holding the tone map used during PLC transmission. The first 70 bits hold the active OFDM tones, The last two bits are reserved for future usage. |
| ToneMask | OCTET STRING (SIZE (9)) | current | A 72-bit string holding the tone mask used during PLC transmission. The first 70 bits hold the active OFDM tones, The last two bits are reserved for future usage. |
| TrueOrFalse | INTEGER { false(0), true(1) } | current | Represents a boolean value (starting at zero). |
| Utf8String | OCTET STRING | current | Character sequence limited to visible ISO-10646 UTF-8 characters (RFC3629). Control characters are tolerated, though discouraged from being used. |