G6-HARDWARE-MIB
120 objects
Microsens private MIB for Generation 6 Ethernet Switches
Imported Objects
| MICROSENS-G6-MIB | g6 |
| SNMPv2-SMI | Counter32 enterprises Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString MacAddress |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.3181.10.6.1 | Identitydevice | Microsens private MIB for Generation 6 Ethernet Switches | ||
| 1.3.6.1.4.1.3181.10.6.1.31 | Nodehardware | |||
| 1.3.6.1.4.1.3181.10.6.1.31.1 | ScalarhardwareLedTest | read-write | current | Runs a leds test whereby all LED light up in all possible colors for checking their function. The tests terminates within a few seconds. |
| 1.3.6.1.4.1.3181.10.6.1.31.2 | ScalarhardwareLedMode | read-write | current | The LED display can be configured to be less intrusive. |
| 1.3.6.1.4.1.3181.10.6.1.31.3 | ScalarhardwarePowerSupply1Monitored | read-write | current | When disabled a missing power supply 1 will not turn the associated led red on failure. Do this when single power supply 2 operation is used or when the device… |
| 1.3.6.1.4.1.3181.10.6.1.31.4 | ScalarhardwarePowerSupply2Monitored | read-write | current | When disabled a missing power supply 2 will not turn the associated led red on failure. Do this when single power supply 1 operation is used or when the device… |
| 1.3.6.1.4.1.3181.10.6.1.31.5 | ScalarhardwareFactoryResetButton | read-write | current | When disabled the factory button will trigger the factory reset function when pressed for a long time. The IP discover function upon a short button click is no… |
| 1.3.6.1.4.1.3181.10.6.1.31.6 | TablecableTestConfigTable | not-accessible | current | The cable tester allows for detection of copper cable faults and can even detect where the fault is located. |
| 1.3.6.1.4.1.3181.10.6.1.31.6.1 | RowcableTestConfigEntry | not-accessible | current | |
| 1.3.6.1.4.1.3181.10.6.1.31.6.1.1 | ColumncableTestConfigPortIndex | not-accessible | current | Automatically generated |
| 1.3.6.1.4.1.3181.10.6.1.31.6.1.2 | ColumncableTestConfigEnableAutoCableTest | read-write | current | When enabled a cable test is performed each time the link goes down. The test is only performed for copper ports or dual media ports in copper mode. |
| 1.3.6.1.4.1.3181.10.6.1.31.6.1.3 | ColumncableTestConfigEventGeneration | read-write | current | When the cable termination status changes an event can be raised. |
| 1.3.6.1.4.1.3181.10.6.1.31.6.1.4 | ColumncableTestConfigReflectionThreshold | read-write | current | Select a value up to 508 which is used to decide between a connected cable and a remotely disconnected cable. With actively terminated data ports, the detectio… |
| 1.3.6.1.4.1.3181.10.6.1.31.6.1.5 | ColumncableTestConfigReflectionHysteresis | read-write | current | Choose value to prevent oscillation when reflection value is slightly shifting. |
| 1.3.6.1.4.1.3181.10.6.1.31.6.1.6 | ColumncableTestConfigStartTestNow | read-write | current | May be used to manually start a cable test. ATTENTION: If the port is in link up status it will be forced to link down first. This will disrupt the current dat… |
| 1.3.6.1.4.1.3181.10.6.1.31.7 | TableioSignalConfigTable | not-accessible | current | |
| 1.3.6.1.4.1.3181.10.6.1.31.7.1 | RowioSignalConfigEntry | not-accessible | current | |
| 1.3.6.1.4.1.3181.10.6.1.31.7.1.1 | ColumnioSignalConfigIndex | not-accessible | current | Automatically generated |
| 1.3.6.1.4.1.3181.10.6.1.31.7.1.2 | ColumnioSignalConfigSignalMode | read-write | current | Permit setting of io signal LEDs and relays to static or blink blink mode for increased visualization. |
| 1.3.6.1.4.1.3181.10.6.1.31.7.1.3 | ColumnioSignalConfigInput1Mode | read-write | current | When this function is activated the external alarm input 1 is monitored. Note: alarm inputs are not available in all product versions. |
| 1.3.6.1.4.1.3181.10.6.1.31.7.1.4 | ColumnioSignalConfigInput1Name | read-write | current | A customer specific name can be specified for input 1. This name will appear in the associated event messages. |
| 1.3.6.1.4.1.3181.10.6.1.31.7.1.5 | ColumnioSignalConfigInput2Mode | read-write | current | When this function is activated the external alarm input 2 is monitored. Note: alarm inputs are not available in all product versions. |
| 1.3.6.1.4.1.3181.10.6.1.31.7.1.6 | ColumnioSignalConfigInput2Name | read-write | current | A customer specific name can be specified for input 2. This name will appear in the associated event messages. |
| 1.3.6.1.4.1.3181.10.6.1.31.7.1.7 | ColumnioSignalConfigOutput1Trigger | read-write | current | Defines on which condition the alarm relay 1 is activated. Note: alarm relays are not available in all product versions. |
| 1.3.6.1.4.1.3181.10.6.1.31.7.1.8 | ColumnioSignalConfigOutput1Name | read-write | current | A customer specific name can be specified for alarm output 1. This name will appear in the associated event messages. |
| 1.3.6.1.4.1.3181.10.6.1.31.7.1.9 | ColumnioSignalConfigOutput2Trigger | read-write | current | Defines on which condition the alarm relay 2 is activated. Note: alarm relays are not available in all product versions. |
| 1.3.6.1.4.1.3181.10.6.1.31.7.1.10 | ColumnioSignalConfigOutput2Name | read-write | current | A customer specific name can be specified for alarm output 2. This name will appear in the associated event messages. |
| 1.3.6.1.4.1.3181.10.6.1.31.100 | ScalarhardwarePowerSupply1Status | read-only | current | Displays state of primary supply or only supply for single supply systems. |
| 1.3.6.1.4.1.3181.10.6.1.31.101 | ScalarhardwarePowerSupply2Status | read-only | current | Displays state of secondary supply if available. |
| 1.3.6.1.4.1.3181.10.6.1.31.102 | ScalarhardwareRunningOnPoe | read-only | current | When set the unit currently operates on the PD input via PoE. |
| 1.3.6.1.4.1.3181.10.6.1.31.103 | ScalarhardwareFanStatus | read-only | current | Displays state of cooling fan. Indicates UNUSED in fanless devices. |
| 1.3.6.1.4.1.3181.10.6.1.31.104 | ScalarhardwareSdCardStatus | read-only | current | Current status of SD-card. |
| 1.3.6.1.4.1.3181.10.6.1.31.105 | ScalarhardwareNumOfPorts | read-only | current | Total number of Ethernet ports this hardware offers. |
| 1.3.6.1.4.1.3181.10.6.1.31.106 | ScalarhardwareMaskOfExistingPorts | read-only | current | Set bit for each port that physically exisiting and could be in use. |
| 1.3.6.1.4.1.3181.10.6.1.31.107 | ScalarhardwareMaskOfSfpPorts | read-only | current | Marks which ports support SFPs. |
| 1.3.6.1.4.1.3181.10.6.1.31.108 | ScalarhardwareMaskOfPoePorts | read-only | current | Marks which ports support PoE output. |
| 1.3.6.1.4.1.3181.10.6.1.31.109 | TablemoduleInfoTable | not-accessible | current | This section indicates which modules are inserted in the optional extension slots. |
| 1.3.6.1.4.1.3181.10.6.1.31.109.1 | RowmoduleInfoEntry | not-accessible | current | |
| 1.3.6.1.4.1.3181.10.6.1.31.109.1.1 | ColumnmoduleInfoIndex | not-accessible | current | Automatically generated |
| 1.3.6.1.4.1.3181.10.6.1.31.109.1.2 | ColumnmoduleInfoUnitType | read-only | current | Identfies the general type of module. |
| 1.3.6.1.4.1.3181.10.6.1.31.109.1.3 | ColumnmoduleInfoArticleNumber | read-only | current | The article number of the module in this slot. |
| 1.3.6.1.4.1.3181.10.6.1.31.109.1.4 | ColumnmoduleInfoSerialNumber | read-only | current | The serial number of the module in this slot. |
| 1.3.6.1.4.1.3181.10.6.1.31.109.1.5 | ColumnmoduleInfoHardwareVersion | read-only | current | This device hardware revision number. |
| 1.3.6.1.4.1.3181.10.6.1.31.109.1.6 | ColumnmoduleInfoProjectNumber | read-only | current | MICROSENS project number. |
| 1.3.6.1.4.1.3181.10.6.1.31.109.1.7 | ColumnmoduleInfoOccupiedSlots | read-only | current | Lists all slots contained in this module. |
| 1.3.6.1.4.1.3181.10.6.1.31.109.1.8 | ColumnmoduleInfoDescription | read-only | current | Feature summary of the module. |
| 1.3.6.1.4.1.3181.10.6.1.31.110 | TableslotInfoTable | not-accessible | current | This section indicates which modules are inserted in the optional extension slots. |
| 1.3.6.1.4.1.3181.10.6.1.31.110.1 | RowslotInfoEntry | not-accessible | current | |
| 1.3.6.1.4.1.3181.10.6.1.31.110.1.1 | ColumnslotInfoIndex | not-accessible | current | Automatically generated |
| 1.3.6.1.4.1.3181.10.6.1.31.110.1.2 | ColumnslotInfoBoardType | read-only | current | General type of board function |
| 1.3.6.1.4.1.3181.10.6.1.31.110.1.3 | ColumnslotInfoBoardId | read-only | current | This identifies the board type for internal operation. |
| 1.3.6.1.4.1.3181.10.6.1.31.110.1.4 | ColumnslotInfoVersionBits | read-only | current | Version bits from hardware or backplane. |
| 1.3.6.1.4.1.3181.10.6.1.31.111 | TableportInfoTable | not-accessible | current | Used to map physical to logical port ids. |
| 1.3.6.1.4.1.3181.10.6.1.31.111.1 | RowportInfoEntry | not-accessible | current | |
| 1.3.6.1.4.1.3181.10.6.1.31.111.1.1 | ColumnportInfoPortIndex | not-accessible | current | Automatically generated |
| 1.3.6.1.4.1.3181.10.6.1.31.111.1.2 | ColumnportInfoSystemSlot | read-only | current | Describes on which system slot this port index is located. |
| 1.3.6.1.4.1.3181.10.6.1.31.111.1.3 | ColumnportInfoSwitchPort | read-only | current | Describes on which switch port this port index is located. |
| 1.3.6.1.4.1.3181.10.6.1.31.111.1.4 | ColumnportInfoUserSlot | read-only | current | Slot number as seen by customer. |
| 1.3.6.1.4.1.3181.10.6.1.31.111.1.5 | ColumnportInfoUserPort | read-only | current | Port number as seen by customer. |
| 1.3.6.1.4.1.3181.10.6.1.31.111.1.6 | ColumnportInfoSnmpPort | read-only | current | Slot and port representation as used in SNMP. Formula is Slot*100 + Port. |
| 1.3.6.1.4.1.3181.10.6.1.31.111.1.7 | ColumnportInfoSnmpInstance | read-only | current | Port instance counting from 0 to number of ports |
| 1.3.6.1.4.1.3181.10.6.1.31.111.1.8 | ColumnportInfoHardwarePort | read-only | current | Port number as used internally. Ports may not be in sequential order. |
| 1.3.6.1.4.1.3181.10.6.1.31.111.1.9 | ColumnportInfoInterfaceType | read-only | current | Identifies port as copper or optical. Also used for snmp ifType definition |
| 1.3.6.1.4.1.3181.10.6.1.31.111.1.10 | ColumnportInfoProperties | read-only | current | Describes which functions the port can support. |
| 1.3.6.1.4.1.3181.10.6.1.31.112 | TableportLedsTable | not-accessible | current | This section indicates the state of all port related LEDs. |
| 1.3.6.1.4.1.3181.10.6.1.31.112.1 | RowportLedsEntry | not-accessible | current | |
| 1.3.6.1.4.1.3181.10.6.1.31.112.1.1 | ColumnportLedsPortIndex | not-accessible | current | Automatically generated |
| 1.3.6.1.4.1.3181.10.6.1.31.112.1.2 | ColumnportLedsEthernetColor | read-only | current | Ethernet Link LED. |
| 1.3.6.1.4.1.3181.10.6.1.31.112.1.3 | ColumnportLedsEthernetBlinking | read-only | current | Ethernet Link LED. |
| 1.3.6.1.4.1.3181.10.6.1.31.112.1.4 | ColumnportLedsPoeColor | read-only | current | Power over Ethernet LED. For optical ports this indicates signal detect status. |
| 1.3.6.1.4.1.3181.10.6.1.31.112.1.5 | ColumnportLedsPoeBlinking | read-only | current | Power over Ethernet LED. For optical ports this indicates signal detect status. |
| 1.3.6.1.4.1.3181.10.6.1.31.113 | TabledeviceLedsTable | not-accessible | current | This section indicates the state of all LEDs which are not port related. Please note: Not every unit offers all LEDs. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1 | RowdeviceLedsEntry | not-accessible | current | |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.1 | ColumndeviceLedsIndex | not-accessible | current | Automatically generated |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.2 | ColumndeviceLedsSystem1Color | read-only | current | This status corresponds to 'sys' LED on some devices. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.3 | ColumndeviceLedsSystem1Blinking | read-only | current | This status corresponds to 'sys' LED on some devices. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.4 | ColumndeviceLedsSystem2Color | read-only | current | Displays external management activity. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.5 | ColumndeviceLedsSystem2Blinking | read-only | current | Displays external management activity. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.6 | ColumndeviceLedsPowerOn1Color | read-only | current | This status corresponds to 'on' LED on some devices. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.7 | ColumndeviceLedsPowerOn1Blinking | read-only | current | This status corresponds to 'on' LED on some devices. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.8 | ColumndeviceLedsPowerOn2Color | read-only | current | Alternative power input LED. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.9 | ColumndeviceLedsPowerOn2Blinking | read-only | current | Alternative power input LED. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.10 | ColumndeviceLedsRing1Color | read-only | current | This LED is used when ring protection is enabled. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.11 | ColumndeviceLedsRing1Blinking | read-only | current | This LED is used when ring protection is enabled. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.12 | ColumndeviceLedsRing2Color | read-only | current | This LED is used when ring protection is enabled. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.13 | ColumndeviceLedsRing2Blinking | read-only | current | This LED is used when ring protection is enabled. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.14 | ColumndeviceLedsSignalIn1Color | read-only | current | Indicates status of alarm input 1. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.15 | ColumndeviceLedsSignalIn1Blinking | read-only | current | Indicates status of alarm input 1. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.16 | ColumndeviceLedsSignalIn2Color | read-only | current | Indicates status of alarm input 2. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.17 | ColumndeviceLedsSignalIn2Blinking | read-only | current | Indicates status of alarm input 2. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.18 | ColumndeviceLedsSignalOut1Color | read-only | current | Indicates status of alarm relay output 1. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.19 | ColumndeviceLedsSignalOut1Blinking | read-only | current | Indicates status of alarm relay output 1. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.20 | ColumndeviceLedsSignalOut2Color | read-only | current | Indicates status of alarm relay output 2. |
| 1.3.6.1.4.1.3181.10.6.1.31.113.1.21 | ColumndeviceLedsSignalOut2Blinking | read-only | current | Indicates status of alarm relay output 2. |
| 1.3.6.1.4.1.3181.10.6.1.31.114 | TablecableTestStatusTable | not-accessible | current | This table display the result of the last cable test. Values are only available for copper ports while a link is down and if the cable test function is enabled. |
| 1.3.6.1.4.1.3181.10.6.1.31.114.1 | RowcableTestStatusEntry | not-accessible | current | |
| 1.3.6.1.4.1.3181.10.6.1.31.114.1.1 | ColumncableTestStatusPortIndex | not-accessible | current | Automatically generated |
| 1.3.6.1.4.1.3181.10.6.1.31.114.1.2 | ColumncableTestStatusUpdateTimeStamp | read-only | current | Indicates the time when this record was last updated. |
| 1.3.6.1.4.1.3181.10.6.1.31.114.1.3 | ColumncableTestStatusPair0State | read-only | current | Indicates line termination test results for wire pair 0 (Pins 1/2) |
| 1.3.6.1.4.1.3181.10.6.1.31.114.1.4 | ColumncableTestStatusPair0DistanceToFault | read-only | current | Distance to fault on wire pair 0 in centimeters. Indicates 0 when no fault is detected or the function is unused. |
| 1.3.6.1.4.1.3181.10.6.1.31.114.1.5 | ColumncableTestStatusPair1State | read-only | current | Indicates line termination test results for wire pair 1 (Pins 3/6) |
| 1.3.6.1.4.1.3181.10.6.1.31.114.1.6 | ColumncableTestStatusPair1DistanceToFault | read-only | current | Distance to fault on wire pair 1 in centimeters. Indicates 0 when no fault is detected or the function is unused. |
| 1.3.6.1.4.1.3181.10.6.1.31.114.1.7 | ColumncableTestStatusPair2State | read-only | current | Indicates line termination test results for wire pair 2 (Pins 4/5) |
| 1.3.6.1.4.1.3181.10.6.1.31.114.1.8 | ColumncableTestStatusPair2DistanceToFault | read-only | current | Distance to fault on wire pair 2 in centimeters. Indicates 0 when no fault is detected or the function is unused. |
| 1.3.6.1.4.1.3181.10.6.1.31.114.1.9 | ColumncableTestStatusPair3State | read-only | current | Indicates line termination test results for wire pair 3 (Pins 7/8) |
| 1.3.6.1.4.1.3181.10.6.1.31.114.1.10 | ColumncableTestStatusPair3DistanceToFault | read-only | current | Distance to fault on wire pair 3 in centimeters. Indicates 0 when no fault is detected or the function is unused. |
| 1.3.6.1.4.1.3181.10.6.1.31.114.1.11 | ColumncableTestStatusReflectionValue | read-only | current | A unitless value that indicates a measure of reflection level. For difficult to detect actively terminated devices perform a measurement with remotely plugged-… |
| 1.3.6.1.4.1.3181.10.6.1.31.114.1.12 | ColumncableTestStatusCableStatus | read-only | current | Indicates the concluded status summary. |
| 1.3.6.1.4.1.3181.10.6.1.31.115 | TableioSignalStatusTable | not-accessible | current | This section is only used for devices which offer external signal inputs and outputs. |
| 1.3.6.1.4.1.3181.10.6.1.31.115.1 | RowioSignalStatusEntry | not-accessible | current | |
| 1.3.6.1.4.1.3181.10.6.1.31.115.1.1 | ColumnioSignalStatusIndex | not-accessible | current | Automatically generated |
| 1.3.6.1.4.1.3181.10.6.1.31.115.1.2 | ColumnioSignalStatusInput1AlarmActive | read-only | current | Indicates true when the input 1 is logically active. |
| 1.3.6.1.4.1.3181.10.6.1.31.115.1.3 | ColumnioSignalStatusInput2AlarmActive | read-only | current | Indicates true when the input 2 is logically active. |
| 1.3.6.1.4.1.3181.10.6.1.31.115.1.4 | ColumnioSignalStatusOutput1RelayActive | read-only | current | Indicates true when the output 1 relay is activated. |
| 1.3.6.1.4.1.3181.10.6.1.31.115.1.5 | ColumnioSignalStatusOutput2RelayActive | read-only | current | Indicates true when the output 2 relay is activated. |
| 1.3.6.1.4.1.3181.10.6.1.31.116 | TabletcamStatusTable | not-accessible | current | The TCAM is a programmable wire speed packet filter. The filter is controlled by the system automatically. This table indicates which filters have been set. |
| 1.3.6.1.4.1.3181.10.6.1.31.116.1 | RowtcamStatusEntry | not-accessible | current | |
| 1.3.6.1.4.1.3181.10.6.1.31.116.1.1 | ColumntcamStatusIndex | not-accessible | current | Automatically generated |
| 1.3.6.1.4.1.3181.10.6.1.31.116.1.2 | ColumntcamStatusControlFile | read-only | current | Reflects the name of the control file associated with this tcam entry. |
| 1.3.6.1.4.1.3181.10.6.1.31.116.1.3 | ColumntcamStatusDescription | read-only | current | Descriptive text what explains what this tcam entry will do. |