MIB Viewer

GESINGLEUPS-MIB

261 objects
The MIB module to describe GE Digital Energy Uninterruptible Power Supplies.
Imported Objects
SNMPv2-SMICounter32 enterprises Gauge32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-IDENTITY OBJECT-TYPE Unsigned32
SNMPv2-TCAutonomousType DisplayString TestAndIncr TEXTUAL-CONVENTION TimeInterval TimeStamp
OIDNameAccessStatusDescription
1.3.6.1.4.1.818IdentityimvThe MIB module to describe GE Digital Energy Uninterruptible Power Supplies.
1.3.6.1.4.1.818.1NodegeHardware
1.3.6.1.4.1.818.1.1NodegeUPS
1.3.6.1.4.1.818.1.1.1ScalargeDiscoveredUPSsMaskread-onlycurrentReading this variable returns bit mask indicating which UPSs in a parallel system are alive. Management software should poll only these UPSs on their snmp bran…
1.3.6.1.4.1.818.1.1.2ScalargeRequestPacketread-writecurrentPut the string, formatted as a IMV/CP4 packet, directly to internally RS485 bus. This OID could be used for accede directly to the internally RS485 bus from a …
1.3.6.1.4.1.818.1.1.3ScalargeReplyPacketread-onlycurrentContain the reply of the IMV/CP4 request packet sent using the OID geRequestPacket. Every time that a write command has be made at the OID ge RequestPacket, th…
1.3.6.1.4.1.818.1.1.10NodegeGenericUPS
1.3.6.1.4.1.818.1.1.10.1NodeupsIdentgen
1.3.6.1.4.1.818.1.1.10.1.1ScalarupsIdentManufacturergenread-onlycurrentThe name of the UPS manufacturer.(*)
1.3.6.1.4.1.818.1.1.10.1.2ScalarupsIdentModelgenread-onlycurrentThe UPS Model designation.(*)
1.3.6.1.4.1.818.1.1.10.1.3ScalarupsIdentUPSSoftwareVersiongenread-onlycurrentThe UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)
1.3.6.1.4.1.818.1.1.10.1.4ScalarupsIdentAgentSoftwareVersiongenread-onlycurrentThe UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)
1.3.6.1.4.1.818.1.1.10.1.5ScalarupsIdentNamegenread-writecurrentA string identifying the UPS. This object should be set by the administrator.(*)
1.3.6.1.4.1.818.1.1.10.1.6ScalarupsIdentAttachedDevicesgenread-writecurrentA string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)
1.3.6.1.4.1.818.1.1.10.1.7ScalarupsIdentUPSSerialNumbergenread-onlycurrentThe UPS serial number
1.3.6.1.4.1.818.1.1.10.1.8ScalarupsIdentComProtVersiongenread-onlycurrentThe IMV communication protocol version
1.3.6.1.4.1.818.1.1.10.1.9ScalarupsIdentOperatingTimegenread-onlycurrentThe present value of the operating time. total 'on' time since UPS manufactured
1.3.6.1.4.1.818.1.1.10.2NodeupsBatterygen
1.3.6.1.4.1.818.1.1.10.2.1ScalarupsBatteryStatusgenread-onlycurrentThe indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfi…
1.3.6.1.4.1.818.1.1.10.2.2ScalarupsSecondsOnBatterygenread-onlycurrentIf the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last res…
1.3.6.1.4.1.818.1.1.10.2.3ScalarupsEstimatedMinutesRemaininggenread-onlycurrentAn estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and…
1.3.6.1.4.1.818.1.1.10.2.4ScalarupsEstimatedChargeRemaininggenread-onlycurrentAn estimate of the battery charge remaining expressed as a percent of full charge.(*)
1.3.6.1.4.1.818.1.1.10.2.5ScalarupsBatteryVoltagegenread-onlycurrentThe magnitude of the present battery voltage.(*)
1.3.6.1.4.1.818.1.1.10.2.6ScalarupsBatteryCurrentgenread-onlycurrentThe present battery current.(*)
1.3.6.1.4.1.818.1.1.10.2.7ScalarupsBatteryTemperaturegenread-onlycurrentThe ambient temperature at or near the UPS Battery casing.(*)
1.3.6.1.4.1.818.1.1.10.2.8ScalarupsBatteryRipplegenread-onlycurrentThe present DC link RMS voltage ripple.(*)
1.3.6.1.4.1.818.1.1.10.3NodeupsInputgen
1.3.6.1.4.1.818.1.1.10.3.1ScalarupsInputLineBadsgenread-onlycurrentA count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the i…
1.3.6.1.4.1.818.1.1.10.3.2ScalarupsInputNumLinesgenread-onlycurrentThe number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)
1.3.6.1.4.1.818.1.1.10.3.3TableupsInputGenTablenot-accessiblecurrentA list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)
1.3.6.1.4.1.818.1.1.10.3.3.1RowupsInputGenEntrynot-accessiblecurrentAn entry containing information applicable to a particular input line.(*)
1.3.6.1.4.1.818.1.1.10.3.3.1.1ColumnupsInputLineIndexgennot-accessiblecurrentThe input line identifier.(*)
1.3.6.1.4.1.818.1.1.10.3.3.1.2ColumnupsInputFrequencygenread-onlycurrentThe present input frequency.(*)
1.3.6.1.4.1.818.1.1.10.3.3.1.3ColumnupsInputVoltagegenread-onlycurrentThe magnitude of the present input voltage.(*)
1.3.6.1.4.1.818.1.1.10.3.3.1.4ColumnupsInputCurrentgenread-onlycurrentThe magnitude of the present input current.(*)
1.3.6.1.4.1.818.1.1.10.3.3.1.5ColumnupsInputTruePowergenread-onlycurrentThe magnitude of the present input true power.(*)
1.3.6.1.4.1.818.1.1.10.3.3.1.6ColumnupsInputVoltageMingenread-onlycurrentThe lowest magnitude of the input voltage since last read out.
1.3.6.1.4.1.818.1.1.10.3.3.1.7ColumnupsInputVoltageMaxgenread-onlycurrentThe highest magnitude of the input voltage since last read out.
1.3.6.1.4.1.818.1.1.10.4NodeupsOutputgen
1.3.6.1.4.1.818.1.1.10.4.1ScalarupsOutputSourcegenread-onlycurrentThe present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the…
1.3.6.1.4.1.818.1.1.10.4.2ScalarupsOutputFrequencygenread-onlycurrentThe present output frequency.(*)
1.3.6.1.4.1.818.1.1.10.4.3ScalarupsOutputNumLinesgenread-onlycurrentThe number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)
1.3.6.1.4.1.818.1.1.10.4.4TableupsOutputGenTablenot-accessiblecurrentA list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)
1.3.6.1.4.1.818.1.1.10.4.4.1RowupsOutputGenEntrynot-accessiblecurrentAn entry containing information applicable to a particular output line.(*)
1.3.6.1.4.1.818.1.1.10.4.4.1.1ColumnupsOutputLineIndexgennot-accessiblecurrentThe output line identifier.(*)
1.3.6.1.4.1.818.1.1.10.4.4.1.2ColumnupsOutputVoltagegenread-onlycurrentThe present output voltage.(*)
1.3.6.1.4.1.818.1.1.10.4.4.1.3ColumnupsOutputCurrentgenread-onlycurrentThe present output current.(*)
1.3.6.1.4.1.818.1.1.10.4.4.1.4ColumnupsOutputPowergenread-onlycurrentThe present output true power.(*)
1.3.6.1.4.1.818.1.1.10.4.4.1.5ColumnupsOutputPercentLoadgenread-onlycurrentThe percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent…
1.3.6.1.4.1.818.1.1.10.4.4.1.6ColumnupsOutputPowerFactorgenread-onlycurrentThe present output power factor. The returned value correspond to the cosf of the load. A positive value indicate an inductive load; a negative value indicate …
1.3.6.1.4.1.818.1.1.10.4.4.1.7ColumnupsOutputPeakCurrentgenread-onlycurrentThe present output peak current.(*)
1.3.6.1.4.1.818.1.1.10.4.4.1.8ColumnupsOutputShareCurrentgenread-onlycurrentIn a parallel system ideally all the UPS are requested to contribute to the load with the same amount of current, i.e. with no current share. The current share…
1.3.6.1.4.1.818.1.1.10.5NodeupsBypassgen
1.3.6.1.4.1.818.1.1.10.5.1ScalarupsBypassFrequencygenread-onlycurrentThe present bypass frequency.(*)
1.3.6.1.4.1.818.1.1.10.5.2ScalarupsBypassNumLinesgenread-onlycurrentThe number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)
1.3.6.1.4.1.818.1.1.10.5.3TableupsBypassGenTablenot-accessiblecurrentA list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)
1.3.6.1.4.1.818.1.1.10.5.3.1RowupsBypassGenEntrynot-accessiblecurrentAn entry containing information applicable to a particular bypass input.(*)
1.3.6.1.4.1.818.1.1.10.5.3.1.1ColumnupsBypassLineIndexgennot-accessiblecurrentThe bypass line identifier.(*)
1.3.6.1.4.1.818.1.1.10.5.3.1.2ColumnupsBypassVoltagegenread-onlycurrentThe present bypass voltage.(*)
1.3.6.1.4.1.818.1.1.10.5.3.1.3ColumnupsBypassCurrentgenread-onlycurrentThe present bypass current.(*)
1.3.6.1.4.1.818.1.1.10.5.3.1.4ColumnupsBypassPowergenread-onlycurrentThe present true power conveyed by the bypass.(*)
1.3.6.1.4.1.818.1.1.10.6NodeupsAlarmgen
1.3.6.1.4.1.818.1.1.10.6.1ScalarupsAlarmsPresentgenread-onlycurrentThe present number of active alarm conditions.(*)
1.3.6.1.4.1.818.1.1.10.6.2TableupsAlarmGenTablenot-accessiblecurrentA list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is …
1.3.6.1.4.1.818.1.1.10.6.2.1RowupsAlarmGenEntrynot-accessiblecurrentAn entry containing information applicable to a particular alarm.(*)
1.3.6.1.4.1.818.1.1.10.6.2.1.1ColumnupsAlarmIdgennot-accessiblecurrentA unique identifier for an alarm condition. This value must remain constant.(*)
1.3.6.1.4.1.818.1.1.10.6.2.1.2ColumnupsAlarmDescrgenread-onlycurrentA reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm con…
1.3.6.1.4.1.818.1.1.10.6.2.1.3ColumnupsAlarmTimegenread-onlycurrentThe value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before ag…
1.3.6.1.4.1.818.1.1.10.6.3NodeupsWellKnownAlarmsgen
1.3.6.1.4.1.818.1.1.10.6.3.1IdentityupsAlarmBatteryBadgencurrentOne or more batteries have been determined to require replacement.(*)
1.3.6.1.4.1.818.1.1.10.6.3.2IdentityupsAlarmOnBatterygencurrentThe UPS is drawing power from the batteries.(*)
1.3.6.1.4.1.818.1.1.10.6.3.3IdentityupsAlarmLowBatterygencurrentThe remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)
1.3.6.1.4.1.818.1.1.10.6.3.4IdentityupsAlarmDepletedBatterygencurrentThe UPS will be unable to sustain the present load when and if the utility power is lost.(*)
1.3.6.1.4.1.818.1.1.10.6.3.5IdentityupsAlarmTempBadgencurrentA temperature is out of tolerance.(*)
1.3.6.1.4.1.818.1.1.10.6.3.6IdentityupsAlarmInputBadgencurrentAn input condition is out of tolerance.(*)
1.3.6.1.4.1.818.1.1.10.6.3.7IdentityupsAlarmOutputBadgencurrentAn output condition (other than OutputOverload) is out of tolerance.(*)
1.3.6.1.4.1.818.1.1.10.6.3.8IdentityupsAlarmOutputOverloadgencurrentThe output load exceeds the UPS output capacity.(*)
1.3.6.1.4.1.818.1.1.10.6.3.9IdentityupsAlarmOnBypassgencurrentThe Bypass is presently engaged on the UPS.(*)
1.3.6.1.4.1.818.1.1.10.6.3.10IdentityupsAlarmBypassBadgencurrentThe Bypass is out of tolerance.(*)
1.3.6.1.4.1.818.1.1.10.6.3.11IdentityupsAlarmOutputOffAsRequestedgencurrentThe UPS has shutdown as requested, i.e., the output is off.(*)
1.3.6.1.4.1.818.1.1.10.6.3.12IdentityupsAlarmUpsOffAsRequestedgencurrentThe entire UPS has shutdown as commanded.(*)
1.3.6.1.4.1.818.1.1.10.6.3.13IdentityupsAlarmChargerFailedgencurrentAn uncorrected problem has been detected within the UPS charger subsystem.(*)
1.3.6.1.4.1.818.1.1.10.6.3.14IdentityupsAlarmUpsOutputOffgencurrentThe output of the UPS is in the off state.(*)
1.3.6.1.4.1.818.1.1.10.6.3.15IdentityupsAlarmUpsSystemOffgencurrentThe UPS system is in the off state.(*)
1.3.6.1.4.1.818.1.1.10.6.3.16IdentityupsAlarmFanFailuregencurrentThe failure of one or more fans in the UPS has been detected.(*)
1.3.6.1.4.1.818.1.1.10.6.3.17IdentityupsAlarmFuseFailuregencurrentThe failure of one or more fuses has been detected.(*)
1.3.6.1.4.1.818.1.1.10.6.3.18IdentityupsAlarmGeneralFaultgencurrentA general fault in the UPS has been detected.(*)
1.3.6.1.4.1.818.1.1.10.6.3.19IdentityupsAlarmDiagnosticTestFailedgencurrentThe result of the last diagnostic test indicates a failure.(*)
1.3.6.1.4.1.818.1.1.10.6.3.20IdentityupsAlarmCommunicationsLostgencurrentA problem has been encountered in the communications between the agent and the UPS.(*)
1.3.6.1.4.1.818.1.1.10.6.3.21IdentityupsAlarmAwaitingPowergencurrentThe UPS output is off and the UPS is awaiting the return of input power.(*)
1.3.6.1.4.1.818.1.1.10.6.3.22IdentityupsAlarmShutdownPendinggencurrentA upsShutdownAfterDelay countdown is underway.(*)
1.3.6.1.4.1.818.1.1.10.6.3.23IdentityupsAlarmShutdownImminentgencurrentThe UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.(*)
1.3.6.1.4.1.818.1.1.10.6.3.24IdentityupsAlarmTestInProgressgencurrentA test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of …
1.3.6.1.4.1.818.1.1.10.6.3.25IdentityupsAlarmReceptacleOffgencurrentThe receptacle are switch off
1.3.6.1.4.1.818.1.1.10.6.3.26IdentityupsAlarmHighSpeedBusFailuregencurrentA problem on the High Speed Bus communication is detected
1.3.6.1.4.1.818.1.1.10.6.3.27IdentityupsAlarmHighSpeedBusJACRCFailuregencurrentA High Speed Bus CRC failure on Bus JA is detected
1.3.6.1.4.1.818.1.1.10.6.3.28IdentityupsAlarmConnectivityBusFailuregencurrentA problem on the Connectivity Bus communication is detected
1.3.6.1.4.1.818.1.1.10.6.3.29IdentityupsAlarmHighSpeedBusJBCRCFailuregencurrentA High Speed Bus CRC failure on Bus JB is detected
1.3.6.1.4.1.818.1.1.10.6.3.30IdentityupsAlarmCurrentSharinggencurrentThe UPS detects an high current sharing on the parallel system
1.3.6.1.4.1.818.1.1.10.6.3.31IdentityupsAlarmDCRipplegencurrentThe UPS detects an high ripple voltage on his DC link
1.3.6.1.4.1.818.1.1.10.6.4ScalarupsAlarmMaskAgenread-onlycurrentSpecifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' com…
1.3.6.1.4.1.818.1.1.10.7NodeupsTestgen
1.3.6.1.4.1.818.1.1.10.7.1ScalarupsTestIdgenread-writecurrentThe test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this docu…
1.3.6.1.4.1.818.1.1.10.7.2ScalarupsTestSpinLockgenread-writecurrentA spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress a…
1.3.6.1.4.1.818.1.1.10.7.3ScalarupsTestResultsSummarygenread-onlycurrentThe results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test complete…
1.3.6.1.4.1.818.1.1.10.7.4ScalarupsTestResultsDetailgenread-onlycurrentAdditional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)
1.3.6.1.4.1.818.1.1.10.7.5ScalarupsTestStartTimegenread-onlycurrentThe value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of…
1.3.6.1.4.1.818.1.1.10.7.6ScalarupsTestElapsedTimegenread-onlycurrentThe amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of …
1.3.6.1.4.1.818.1.1.10.7.7NodeupsWellKnownTestsgen
1.3.6.1.4.1.818.1.1.10.7.7.1IdentityupsTestNoTestsInitiatedgencurrentNo tests have been initiated and no test is in progress.(*)
1.3.6.1.4.1.818.1.1.10.7.7.2IdentityupsTestAbortTestInProgressgencurrentThe test in progress is to be aborted / the test in progress was aborted.(*)
1.3.6.1.4.1.818.1.1.10.7.7.3IdentityupsTestGeneralSystemsTestgencurrentThe manufacturer's standard test of UPS device systems.(*)
1.3.6.1.4.1.818.1.1.10.7.7.4IdentityupsTestQuickBatteryTestgencurrentA test that is sufficient to determine if the battery needs replacement.(*)
1.3.6.1.4.1.818.1.1.10.7.7.5IdentityupsTestDeepBatteryCalibrationgencurrentThe system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high deg…
1.3.6.1.4.1.818.1.1.10.8NodeupsControlgen
1.3.6.1.4.1.818.1.1.10.8.1ScalarupsShutdownTypegenread-writecurrentThis object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reach…
1.3.6.1.4.1.818.1.1.10.8.2ScalarupsShutdownAfterDelaygenread-writecurrentSetting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdo…
1.3.6.1.4.1.818.1.1.10.8.3ScalarupsStartupAfterDelaygenread-writecurrentSetting this object will start the output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause …
1.3.6.1.4.1.818.1.1.10.8.4ScalarupsRebootWithDurationgenread-writecurrentSetting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the ti…
1.3.6.1.4.1.818.1.1.10.8.5ScalarupsAutoRestartgenread-writecurrentSetting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutd…
1.3.6.1.4.1.818.1.1.10.8.6ScalarupsReceptaclesNumgenread-onlycurrentThe number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.
1.3.6.1.4.1.818.1.1.10.8.7TableupsReceptacleGenTablenot-accessiblecurrentA list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.
1.3.6.1.4.1.818.1.1.10.8.7.1RowupsReceptacleGenEntrynot-accessiblecurrentAn entry containing information applicable to a particular receptacle.
1.3.6.1.4.1.818.1.1.10.8.7.1.1ColumnupsReceptacleLineIndexgennot-accessiblecurrentThe receptacle line identifier.
1.3.6.1.4.1.818.1.1.10.8.7.1.2ColumnupsReceptacleOnOffgenread-writecurrentThe present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptac…
1.3.6.1.4.1.818.1.1.10.8.8ScalarupsUPSModegenread-writecurrentThe operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transfor…
1.3.6.1.4.1.818.1.1.10.8.9ScalarupsRectifierOnOffgenread-writecurrentThe present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier …
1.3.6.1.4.1.818.1.1.10.8.10ScalarupsBatteryChargeMethodgenread-writecurrentThe present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this objec…
1.3.6.1.4.1.818.1.1.10.8.11ScalarupsInverterOnOffgenread-writecurrentThe present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off…
1.3.6.1.4.1.818.1.1.10.8.12ScalarupsBypassOnOffgenread-writecurrentThe present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If…
1.3.6.1.4.1.818.1.1.10.8.13ScalarupsLoadSourcegenread-writecurrentThe present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will …
1.3.6.1.4.1.818.1.1.10.9NodeupsConfiggen
1.3.6.1.4.1.818.1.1.10.9.1ScalarupsConfigInputVoltagegenread-writecurrentThe magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a v…
1.3.6.1.4.1.818.1.1.10.9.2ScalarupsConfigInputFreqgenread-writecurrentThe nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is no…
1.3.6.1.4.1.818.1.1.10.9.3ScalarupsConfigOutputVoltagegenread-writecurrentThe magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a …
1.3.6.1.4.1.818.1.1.10.9.4ScalarupsConfigOutputFreqgenread-writecurrentThe nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is n…
1.3.6.1.4.1.818.1.1.10.9.5ScalarupsConfigOutputVAgenread-onlycurrentThe magnitude of the nominal Volt-Amp rating.(*)
1.3.6.1.4.1.818.1.1.10.9.6ScalarupsConfigOutputPowergenread-onlycurrentThe magnitude of the nominal true power rating.(*)
1.3.6.1.4.1.818.1.1.10.9.7ScalarupsConfigLowBattTimegenread-writecurrentThe value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the …
1.3.6.1.4.1.818.1.1.10.9.8ScalarupsConfigAudibleStatusgenread-writecurrentThe requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this …
1.3.6.1.4.1.818.1.1.10.9.9ScalarupsConfigLowVoltageTransferPointgenread-writecurrentThe minimum input line voltage allowed before the UPS system transfers to battery backup.(*)
1.3.6.1.4.1.818.1.1.10.9.10ScalarupsConfigHighVoltageTransferPointgenread-writecurrentThe maximum line voltage allowed before the UPS system transfers to battery backup.(*)
1.3.6.1.4.1.818.1.1.10.9.11ScalarupsConfigBatteryCapacitygenread-writecurrentThe installed battery capacity. This value is the 'factory'-value, not the value after calibration.
1.3.6.1.4.1.818.1.1.10.9.12ScalarupsConfigBatteryChargeCurrentgenread-writecurrentThe maximum battery charge current, including external chargers.
1.3.6.1.4.1.818.1.1.10.9.13ScalarupsConfigNoLoadShutdowngenread-writecurrentDis- or enable 'no load' shutdown from the contact interface.
1.3.6.1.4.1.818.1.1.10.9.14ScalarupsConfigStartDelaygenread-writecurrentMinimum required autonomy time before the UPS may perform an autorestart.
1.3.6.1.4.1.818.1.1.10.10NodeupsGetSetgen
1.3.6.1.4.1.818.1.1.10.10.1ScalarupsEventGetNextgenread-writecurrentThe number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The val…
1.3.6.1.4.1.818.1.1.10.10.2ScalarupsEventGetPreviousgenread-writecurrentThe number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The val…
1.3.6.1.4.1.818.1.1.10.10.3ScalarupsEventSetStartingTimeStampgenread-writecurrentThe timestamp which is used as starting point for downloading events from the UPS event buffer
1.3.6.1.4.1.818.1.1.10.10.4ScalarupsEventRetreiveCurrentTimeStampgenread-onlycurrentThe current timestamp is retreived from the UPS
1.3.6.1.4.1.818.1.1.10.10.5ScalarupsEventTableSizegenread-onlycurrentThe number of entries in the event table. This object indicates the number of rows in the event table.
1.3.6.1.4.1.818.1.1.10.10.6TableupsEventGenTablenot-accessiblecurrentA list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the…
1.3.6.1.4.1.818.1.1.10.10.6.1RowupsEventGenEntrynot-accessiblecurrentAn entry containing information applicable to a particular event.
1.3.6.1.4.1.818.1.1.10.10.6.1.1ColumnupsEventLineIndexgennot-accessiblecurrentThe event line identifier.
1.3.6.1.4.1.818.1.1.10.10.6.1.2ColumnupsEventCodegenread-onlycurrentThe event code in numerical format.
1.3.6.1.4.1.818.1.1.10.10.6.1.3ColumnupsEventStatusgenread-onlycurrentThe status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status …
1.3.6.1.4.1.818.1.1.10.10.6.1.4ColumnupsEventTimegenread-onlycurrentThe timestamp of the moment the event was generated.
1.3.6.1.4.1.818.1.1.10.10.7ScalarupsParametersReadgenread-writecurrentThe number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value up…
1.3.6.1.4.1.818.1.1.10.10.8ScalarupsParametersWritegenread-writecurrentThe number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be u…
1.3.6.1.4.1.818.1.1.10.10.9ScalarupsParametersStartAddressgenread-writecurrentThe address which is used as starting point for downloading parameters from the UPS
1.3.6.1.4.1.818.1.1.10.10.10ScalarupsParameterTableSizegenread-onlycurrentThe number of entries in the parameter table. This object indicates the number of rows in the parameter table.
1.3.6.1.4.1.818.1.1.10.10.11TableupsParameterGenTablenot-accessiblecurrentA list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of t…
1.3.6.1.4.1.818.1.1.10.10.11.1RowupsParameterGenEntrynot-accessiblecurrentAn entry containing information applicable to a particular parameter.
1.3.6.1.4.1.818.1.1.10.10.11.1.1ColumnupsParameterLineIndexgennot-accessiblecurrentThe parameter line identifier.
1.3.6.1.4.1.818.1.1.10.10.11.1.2ColumnupsParameterValuegenread-writecurrentThe parameter value in numerical format.
1.3.6.1.4.1.818.1.1.10.10.12ScalarupsStatusgenread-onlycurrentThe global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other comman…
1.3.6.1.4.1.818.1.1.10.10.13ScalarupsMainsStatisticsMBfailgenread-onlycurrentCount of main bypass failures (>200 ms), since UPS installation.
1.3.6.1.4.1.818.1.1.10.10.14ScalarupsMainsStatisticsMRfailgenread-onlycurrentCount of mains rectifier failures (>200 ms), since UPS installation.
1.3.6.1.4.1.818.1.1.10.10.15ScalarupsMainsStatisticsB2genread-onlycurrentCount of transients on the mains bypass (0..2 ms), during the last 7 days.
1.3.6.1.4.1.818.1.1.10.10.16ScalarupsMainsStatisticsB5genread-onlycurrentCount of transients on the mains bypass (2..5 ms), during the last 7 days.
1.3.6.1.4.1.818.1.1.10.10.17ScalarupsMainsStatisticsB10genread-onlycurrentCount of transients on the mains bypass (5..10 ms), during the last 7 days.
1.3.6.1.4.1.818.1.1.10.10.18ScalarupsMainsStatisticsB200genread-onlycurrentCount of transients on the mains bypass (10..200 ms), during the last 7 days.
1.3.6.1.4.1.818.1.1.10.10.19ScalarupsMainsStatisticsBypRelgenread-onlycurrentBypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.
1.3.6.1.4.1.818.1.1.10.10.20ScalarupsTimegenread-writecurrentThe current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp for…
1.3.6.1.4.1.818.1.1.10.10.21ScalarupsRequestPermissiongenread-writecurrentAn encrypted code is send to enable use of restricted write objects during a limited period of time.
1.3.6.1.4.1.818.1.1.10.10.22ScalarupsEventGetCodegenread-writecurrentThe code which is used as starting point to downloading the events from the UPS event buffer.
1.3.6.1.4.1.818.1.1.10.10.23ScalarupsEventSpinLockgenread-writecurrentA spin lock on the event subsystem.
1.3.6.1.4.1.818.1.1.10.10.24ScalarupsParameterSpinLockgenread-writecurrentA spin lock on the parameters subsystem.
1.3.6.1.4.1.818.1.1.10.11NodegeUPSTrapsgen
1.3.6.1.4.1.818.1.1.10.11.1NotificationupsTrapAlarmBatteryBadgencurrentOne or more batteries have been determined to require replacement.
1.3.6.1.4.1.818.1.1.10.11.2NotificationupsTrapAlarmOnBatterygencurrentThe UPS is drawing power from the batteries.
1.3.6.1.4.1.818.1.1.10.11.3NotificationupsTrapAlarmLowBatterygencurrentThe remaining battery run-time is less than or equal to upsConfigLowBattTime.
1.3.6.1.4.1.818.1.1.10.11.4NotificationupsTrapAlarmDepletedBatterygencurrentThe UPS will be unable to sustain the present load when and if the utility power is lost)
1.3.6.1.4.1.818.1.1.10.11.5NotificationupsTrapAlarmTempBadgencurrentA temperature is out of tolerance.
1.3.6.1.4.1.818.1.1.10.11.6NotificationupsTrapAlarmInputBadgencurrentAn input condition is out of tolerance.
1.3.6.1.4.1.818.1.1.10.11.7NotificationupsTrapAlarmOutputBadgencurrentAn output condition (other than OutputOverload) is out of tolerance.
1.3.6.1.4.1.818.1.1.10.11.8NotificationupsTrapAlarmOutputOverloadgencurrentThe output load exceeds the UPS output capacity.
1.3.6.1.4.1.818.1.1.10.11.9NotificationupsTrapAlarmOnBypassgencurrentThe Bypass is presently engaged on the UPS.
1.3.6.1.4.1.818.1.1.10.11.10NotificationupsTrapAlarmBypassBadgencurrentThe Bypass is out of tolerance.
1.3.6.1.4.1.818.1.1.10.11.11NotificationupsTrapAlarmOutputOffAsRequestedgencurrentThe UPS has shutdown as requested, i.e., the output is off.
1.3.6.1.4.1.818.1.1.10.11.12NotificationupsTrapAlarmUpsOffAsRequestedgencurrentThe entire UPS has shutdown as commanded.
1.3.6.1.4.1.818.1.1.10.11.13NotificationupsTrapAlarmChargerFailedgencurrentAn uncorrected problem has been detected within the UPS charger subsystem.
1.3.6.1.4.1.818.1.1.10.11.14NotificationupsTrapAlarmUpsOutputOffgencurrentThe output of the UPS is in the off state.
1.3.6.1.4.1.818.1.1.10.11.15NotificationupsTrapAlarmUpsSystemOffgencurrentThe UPS system is in the off state.
1.3.6.1.4.1.818.1.1.10.11.16NotificationupsTrapAlarmFanFailuregencurrentThe failure of one or more fans in the UPS has been detected.
1.3.6.1.4.1.818.1.1.10.11.17NotificationupsTrapAlarmFuseFailuregencurrentThe failure of one or more fuses has been detected.
1.3.6.1.4.1.818.1.1.10.11.18NotificationupsTrapAlarmGeneralFaultgencurrentA general fault in the UPS has been detected.
1.3.6.1.4.1.818.1.1.10.11.19NotificationupsTrapAlarmDiagnosticTestFailedgencurrentThe result of the last diagnostic test indicates a failure.
1.3.6.1.4.1.818.1.1.10.11.20NotificationupsTrapAlarmCommunicationsLostgencurrentA problem has been encountered in the communication between the agent and the UPS.
1.3.6.1.4.1.818.1.1.10.11.21NotificationupsTrapAlarmAwaitingPowergencurrentThe UPS output is off and the UPS is awaiting the return of the input power (*).
1.3.6.1.4.1.818.1.1.10.11.22NotificationupsTrapAlarmShutdownPendinggencurrentA upsShutdownAfterDelay countdown is underway.
1.3.6.1.4.1.818.1.1.10.11.23NotificationupsTrapAlarmShutdownImminentgencurrentThe UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.
1.3.6.1.4.1.818.1.1.10.11.24NotificationupsTrapAlarmTestInProgressgencurrentA test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of …
1.3.6.1.4.1.818.1.1.10.11.25NotificationupsTrapAlarmReceptacleOffgencurrentA receptacle has been switched off.
1.3.6.1.4.1.818.1.1.10.11.26NotificationupsTrapAlarmHighspeedBusFailuregencurrentA problem on the Highspeed Bus communication is detected.
1.3.6.1.4.1.818.1.1.10.11.27NotificationupsTrapAlarmHighspeedBusJACRCFailuregencurrentA CRC failure on the Highspeed Bus JA is detected.
1.3.6.1.4.1.818.1.1.10.11.28NotificationupsTrapAlarmConnectivityBusFailuregencurrentA Connectivity Bus failure is detected
1.3.6.1.4.1.818.1.1.10.11.29NotificationupsTrapAlarmHighspeedBusJBCRCFailuregencurrentA CRC failure on the Highspeed Bus JB is detected.
1.3.6.1.4.1.818.1.1.10.11.30NotificationupsTrapAlarmCurrentSharingFailuregencurrentAn high current sharing on the parallel system is detected.
1.3.6.1.4.1.818.1.1.10.11.31NotificationupsTrapAlarmDCRippleFailuregencurrentAn high ripple voltage on his DC link is detected.
1.3.6.1.4.1.818.1.1.10.11.33NotificationupsTrapAlarmBatteryBadRestoredgencurrentA Battery bad condition is restored.
1.3.6.1.4.1.818.1.1.10.11.34NotificationupsTrapAlarmOnBatteryRestoredgencurrentThe UPS is drawing power from mains again.
1.3.6.1.4.1.818.1.1.10.11.35NotificationupsTrapAlarmLowBatteryRestoredgencurrentA Low Battery condition is restored.
1.3.6.1.4.1.818.1.1.10.11.36NotificationupsTrapAlarmDepletedBatteryRestoredgencurrentA Depleted Battery condition is restored.
1.3.6.1.4.1.818.1.1.10.11.37NotificationupsTrapAlarmTempBadRestoredgencurrentA bad temperature condition is restored.
1.3.6.1.4.1.818.1.1.10.11.38NotificationupsTrapAlarmInputBadRestoredgencurrentAn input bad condition is restored.
1.3.6.1.4.1.818.1.1.10.11.39NotificationupsTrapAlarmOutputBadRestoredgencurrentAn output bad condition is restored.
1.3.6.1.4.1.818.1.1.10.11.40NotificationupsTrapAlarmOutputOverloadRestoredgencurrentAn output overload condition is restored.
1.3.6.1.4.1.818.1.1.10.11.41NotificationupsTrapAlarmOnBypassRestoredgencurrentAn On Bypass condition is restored.
1.3.6.1.4.1.818.1.1.10.11.42NotificationupsTrapAlarmBypassBadRestoredgencurrentA Bypass bad condition is restored.
1.3.6.1.4.1.818.1.1.10.11.43NotificationupsTrapAlarmOutputOffAsRequestedRestoredgencurrentA request shutdown has been restored.
1.3.6.1.4.1.818.1.1.10.11.44NotificationupsTrapAlarmUpsOffAsRequestedRestoredgencurrentA entire UPS command has been restored.
1.3.6.1.4.1.818.1.1.10.11.45NotificationupsTrapAlarmChargerFailedRestoredgencurrentA Charger Failer condition is restored.
1.3.6.1.4.1.818.1.1.10.11.46NotificationupsTrapAlarmUpsOutputOngencurrentThe output of the UPS switched in the on state.
1.3.6.1.4.1.818.1.1.10.11.47NotificationupsTrapAlarmUpsSystemOngencurrentThe UPS system is switched in the on state.
1.3.6.1.4.1.818.1.1.10.11.48NotificationupsTrapAlarmFanFailureRestoredgencurrentA Fan failure condition is restored.
1.3.6.1.4.1.818.1.1.10.11.49NotificationupsTrapAlarmFuseFailureRestoredgencurrentA Fuse failure condition is restored.
1.3.6.1.4.1.818.1.1.10.11.50NotificationupsTrapAlarmGeneralFaultRestoredgencurrentA general fault is restored.
1.3.6.1.4.1.818.1.1.10.11.51NotificationupsTrapAlarmDiagnosticTestFailedRestoredgencurrentA last diagnostic test indicates a failure is restored.
1.3.6.1.4.1.818.1.1.10.11.52NotificationupsTrapAlarmCommunicationsLostRestoredgencurrentA problem in the communication between the agent and the UPS is restored.
1.3.6.1.4.1.818.1.1.10.11.53NotificationupsTrapAlarmAwaitingPowerRestoredgencurrentA awaiting power condition is restored (*).
1.3.6.1.4.1.818.1.1.10.11.54NotificationupsTrapAlarmShutdownPendingRestoredgencurrentA upsShutdownAfterDelay countdown is restored.
1.3.6.1.4.1.818.1.1.10.11.55NotificationupsTrapAlarmShutdownImminentRestoredgencurrentA shutdown imminent condition is restored.
1.3.6.1.4.1.818.1.1.10.11.56NotificationupsTrapAlarmTestInProgressRestoredgencurrentThe test is in progress is terminated.
1.3.6.1.4.1.818.1.1.10.11.57NotificationupsTrapAlarmReceptacleOncurrentA receptacle has been switched on.
1.3.6.1.4.1.818.1.1.10.11.58NotificationupsTrapAlarmHighspeedBusRestoredgencurrentA problem on the Highspeed Bus communication is restored.
1.3.6.1.4.1.818.1.1.10.11.59NotificationupsTrapAlarmHighspeedBusJACRCRestoredAgencurrentA CRC failure on the Highspeed Bus JA is restored.
1.3.6.1.4.1.818.1.1.10.11.60NotificationupsTrapAlarmConnectivityBusRestoredgencurrentA problem on the Connectivity Bus communication is restored.
1.3.6.1.4.1.818.1.1.10.11.61NotificationupsTrapAlarmHighspeedBusJBCRCRestoredBgencurrentA CRC failure on the Highspeed Bus JB is restored.
1.3.6.1.4.1.818.1.1.10.11.62NotificationupsTrapAlarmCurrentSharingRestoredgencurrentAn high current sharing on the parallel system is restored.
1.3.6.1.4.1.818.1.1.10.11.63NotificationupsTrapAlarmDCRippleRestoredgencurrentAn high ripple voltage on his DC link is restored.
1.3.6.1.4.1.818.1.1.10.11.129NotificationupsTrapAlarmValueLowgencurrentA measurement value reached a value below its low-level threshold.
1.3.6.1.4.1.818.1.1.10.11.130NotificationupsTrapAlarmValueHighgencurrentA measurement value reached a value higher than its high-level threshold.
1.3.6.1.4.1.818.1.1.10.11.133NotificationupsTrapAlarmValueLowRestoredgencurrentA ValueLow alarm condition is restored.
1.3.6.1.4.1.818.1.1.10.11.134NotificationupsTrapAlarmValueHighRestoredgencurrentA ValueHigh alarm condition is restored.
1.3.6.1.4.1.818.1.1.10.12NodeupsDiagnosticgen
1.3.6.1.4.1.818.1.1.10.12.1ScalarupsDiagnosticBusJACommunicationStatusgenread-onlycurrentBit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA …
1.3.6.1.4.1.818.1.1.10.12.2ScalarupsDiagnosticBusJBCommunicationStatusgenread-onlycurrentBit oriented values associated to the ID of the UPS (bit0 = UPS1 ... bit7 = UPS8). The correspondent UPS is not present on the high speed bus communication JA …
1.3.6.1.4.1.818.1.1.10.12.3ScalarupsDiagnosticBatteryLifetimegenread-onlycurrentThe critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data …
1.3.6.1.4.1.818.1.1.10.12.4ScalarupsDiagnosticFansLifetimegenread-onlycurrentThe critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data …
1.3.6.1.4.1.818.1.1.10.12.5ScalarupsDiagnosticDCcapacitorsLifetimegenread-onlycurrentThe critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data …
1.3.6.1.4.1.818.1.1.10.12.6ScalarupsDiagnosticACcapacitorsLifetimegenread-onlycurrentThe critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data …
1.3.6.1.4.1.818.1.1.10.12.7ScalarupsDiagnosticGlobalServiceCheckgenread-onlycurrentThe critical components are associated to Service parameters indicating the remaining lifetime. They are initially set to default values depending to the data …
1.3.6.1.4.1.818.1.100NodegeDevices
1.3.6.1.4.1.818.1.100.1NodegeDevicesDescriptions
1.3.6.1.4.1.818.1.100.1.1NodeadvSNMPWebIntCard
1.3.6.1.4.1.818.1.100.1.2NodesnmpWebIntCard
1.3.6.1.4.1.818.1.100.1.3NodesnmpWebIntBox
Type Definitions
NameSyntaxStatusDescription
NonNegativeInteger32Integer32 (0..2147483647)currentThis data type is a non-negative value.
PositiveInteger32Integer32 (1..2147483647)currentThis data type is a non-zero and non-negative value.