H3C-DOT11-RRM-MIB
122 objects
This MIB file is to provide the object definition of WLAN radio resource management (RRM).
Imported Objects
| H3C-DOT11-REF-MIB | h3cDot11 h3cDot11APElementIndex H3cDot11ChannelScopeType H3cDot11ObjectIDType H3cDot11RadioElementIndex H3cDot11RadioScopeType H3cDot11RadioType H3cDot11SSIDStringType |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DateAndTime MacAddress RowStatus TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2011.10.2.75.8 | Identityh3cDot11RRM | This MIB file is to provide the object definition of WLAN radio resource management (RRM). | ||
| 1.3.6.1.4.1.2011.10.2.75.8.1 | Nodeh3cDot11RRMConfigGroup | |||
| 1.3.6.1.4.1.2011.10.2.75.8.1.1 | Nodeh3cDot11RRMGlobalCfgPara | |||
| 1.3.6.1.4.1.2011.10.2.75.8.1.1.1 | Scalarh3cDot11RRM11nMadtMaxMcs | read-write | current | Specify the maximum modulation and coding scheme (MCS) index for 802.11n mandatory rates. The value 255 indicates that no maximum MCS index is specified. No ma… |
| 1.3.6.1.4.1.2011.10.2.75.8.1.1.2 | Scalarh3cDot11RRM11nSuptMaxMcs | read-write | current | Specify the maximum Modulation and Coding Scheme (MCS) index for 802.11n supported rates. The specified maximum MCS index for 802.11n supported rates must be n… |
| 1.3.6.1.4.1.2011.10.2.75.8.1.1.3 | Scalarh3cDot11RRM11gProtect | read-write | current | Enable/Disable dot11g protection. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.1.4 | Scalarh3cDot11RRM11aPwrConstrt | read-write | current | Configure the power constraint for all 802.11a radios. The configured power constraint is advertised in beacons if spectrum management is enabled. The range of… |
| 1.3.6.1.4.1.2011.10.2.75.8.1.1.5 | Scalarh3cDot11RRM11aSpectrumManag | read-write | current | Enable/Disable spectrum management for 802.11a radios. When spectrum management is enabled, the WLAN sub-system advertises power capabilities of the AP and pow… |
| 1.3.6.1.4.1.2011.10.2.75.8.1.1.6 | Scalarh3cDot11RRMAutoChlAvoid11h | read-write | current | Configure the auto-channel set as non-dot11h channels, this is, only the non-dot11h channels belonging to the country code are scanned during initial channel s… |
| 1.3.6.1.4.1.2011.10.2.75.8.1.1.7 | Scalarh3cDot11RRMScanChl | read-write | current | Set the scan mode. auto: When this option is set, all channels of the country code being set are scanned. all: When this option is set, all the channels of the… |
| 1.3.6.1.4.1.2011.10.2.75.8.1.1.8 | Scalarh3cDot11RRMScanRptIntvel | read-write | current | Set the scan report interval. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.1.9 | Scalarh3cDot11APInterfNumThreshhd | read-write | current | Represents threshold of AP interference . If the value of AP interference exceeds this threshold, AP interference trap will be sent. If the value of this node … |
| 1.3.6.1.4.1.2011.10.2.75.8.1.1.10 | Scalarh3cDot11StaInterfNumThreshhd | read-write | current | Represents threshold of STA interference. If the value of STA interference exceeds this threshold, STA interference trap will be sent. If the value of this nod… |
| 1.3.6.1.4.1.2011.10.2.75.8.1.1.11 | Scalarh3cDot11RRM11nMultiCastMcs | read-write | current | Specify the modulation and coding scheme (MCS) index for 802.11n multicast rates. The value 4294967295 indicates that no MCS index is specified. No MCS index i… |
| 1.3.6.1.4.1.2011.10.2.75.8.1.1.12 | Scalarh3cDot11RRM11acMadtMaxNss | read-write | current | Specify the maximum NSS index for 802.11ac mandatory rates. The value 0 indicates that no maximum NSS index is specified. No maximum NSS index is specified for… |
| 1.3.6.1.4.1.2011.10.2.75.8.1.1.13 | Scalarh3cDot11RRM11acSuptMaxNss | read-write | current | Specify the maximum NSS index for 802.11ac supported rates. The specified maximum NSS index for 802.11ac supported rates must be no less than the specified max… |
| 1.3.6.1.4.1.2011.10.2.75.8.1.1.14 | Scalarh3cDot11RRM11acMultiCastNss | read-write | current | Specify the NSS index for 802.11ac multicast rates. The value 0 indicates that no NSS index is specified. No NSS index is specified for 802.11ac multicast rate… |
| 1.3.6.1.4.1.2011.10.2.75.8.1.1.15 | Scalarh3cDot11RRM11acMultiCastVhtMcs | read-write | current | Specify the MCS index for 802.11ac multicast rates. The value 255 indicates that no MCS index is specified. No MCS index is specified for 802.11ac multicast ra… |
| 1.3.6.1.4.1.2011.10.2.75.8.1.2 | Tableh3cDot11RRMRadioCfgTable | not-accessible | current | Configure WLAN RRM based radio type. When 802.11b parameter is modified, 802.11g parameter will be changed at the same time. In the same way, when 802.11g para… |
| 1.3.6.1.4.1.2011.10.2.75.8.1.2.1 | Rowh3cDot11RRMRadioCfgEntry | not-accessible | current | Configure WLAN RRM based radio type. When 802.11b parameter is modified, 802.11g parameter will be changed at the same time. In the same way, when 802.11g para… |
| 1.3.6.1.4.1.2011.10.2.75.8.1.2.1.1 | Columnh3cDot11RRMRadioType | not-accessible | current | 802.11 radio type. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.2.1.2 | Columnh3cDot11RRMCfgChlState | read-write | current | Enable/Disable dynamic channel selection. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.2.1.3 | Columnh3cDot11RRMCfgChlMode | read-write | current | Configure the mode of channel selection. This node can be configured only when dynamic channel selection is enabled. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.2.1.4 | Columnh3cDot11RRMChlProntoRadioElmt | read-write | current | Specify the AP and radio that will change channel at next calibration cycle. 0 is returned when getting the value of this node. This node can be configured onl… |
| 1.3.6.1.4.1.2011.10.2.75.8.1.2.1.5 | Columnh3cDot11RRMCfgPwrState | read-write | current | Enable/Disable dynamic power selection for the band. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.2.1.6 | Columnh3cDot11RRMCfgPwrMode | read-write | current | Configure the mode of transmit power control. This node can be configured only when dynamic power selection is enabled. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.2.1.7 | Columnh3cDot11RRMPwrProntoRadioElmt | read-write | current | Specify the AP and radio that will change power at next calibration cycle. 0 is returned when getting the value of this node. This node can be configured only … |
| 1.3.6.1.4.1.2011.10.2.75.8.1.2.1.8 | Columnh3cDot11RRMCfgIntrvl | read-write | current | Configure the calibration interval. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.2.1.9 | Columnh3cDot11RRMCfgIntrfThres | read-write | current | Configure the interface threshold. By default, interference observed on an operating channel is considered during dynamic frequency selection and transmit powe… |
| 1.3.6.1.4.1.2011.10.2.75.8.1.2.1.10 | Columnh3cDot11RRMCfgNoiseThres | read-write | current | Configure the noise threshold. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.2.1.11 | Columnh3cDot11RRMCfgPERThres | read-write | current | Configure the CRC error threshold. If the percentage of CRC errors reaches the threshold, RRM will perform resource adjustment to control the situation. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.2.1.12 | Columnh3cDot11RRMCfgToleranceFctr | read-write | current | Configure the tolerance level. During dynamic frequency selection (DFS), the channel will be changed only if there is a better channel having lesser interferen… |
| 1.3.6.1.4.1.2011.10.2.75.8.1.2.1.13 | Columnh3cDot11RRMCfgAdjacencyFctr | read-write | current | Configure the adjacency factor for the band. If transmit power control (TPC) is configured, power will be adjusted when the nth neighbor is detected. The value… |
| 1.3.6.1.4.1.2011.10.2.75.8.1.3 | Tableh3cDot11RRMAPCfgTable | not-accessible | current | This table defines the RRM parameters for AP. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.3.1 | Rowh3cDot11RRMAPCfgEntry | not-accessible | current | Each entry contains information of RRM parameters for AP. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.3.1.1 | Columnh3cDot11RRMAPWorkMode | read-write | current | AP work mode. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.4 | Tableh3cDot11RRMSDRadioGroupTable | not-accessible | current | This table defines RRM self-decisive radio group. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.4.1 | Rowh3cDot11RRMSDRadioGroupEntry | not-accessible | current | Each entry contains information of one RRM self-decisive radio group. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.4.1.1 | Columnh3cDot11RRMSDRadioGroupId | not-accessible | current | Represents RRM self-decisive radio group ID. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.4.1.2 | Columnh3cDot11RRMSDRadioGroupDesc | read-create | current | Represents the description of RRM self-decisive radio group. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.4.1.3 | Columnh3cDot11RRMSDRdGrpChlHolddownTm | read-create | current | Represents the channel holddown time of RRM self-decisive radio group. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.4.1.4 | Columnh3cDot11RRMSDRdGrpPwrHolddownTm | read-create | current | Represents the power holddown time of RRM self-decisive radio group. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.4.1.5 | Columnh3cDot11RRMSDRdGroupRowStatus | read-create | current | The row status of this table entry. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.5 | Tableh3cDot11RRMAPCfg2Table | not-accessible | current | This table defines the RRM parameters for AP. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.5.1 | Rowh3cDot11RRMAPCfg2Entry | not-accessible | current | Each entry contains information of RRM parameters for AP. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.5.1.1 | Columnh3cDot11RRMAPSerialID | not-accessible | current | Serial ID of the AP. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.5.1.2 | Columnh3cDot11RRMAPIntfThreshold | read-write | current | Represents threshold of AP interference . If the number of AP interference exceeds this threshold, AP interference trap will be sent. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.5.1.3 | Columnh3cDot11RRMStaIntfThreshold | read-write | current | Represents threshold of STA interference. If the number of STA interference exceeds this threshold, station interference trap will be sent. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.5.1.4 | Columnh3cDot11RRMCoChlIntfTrapThhd | read-write | current | Represents threshold of interference trap with current ap. If signal strength of the device exceeds this threshold, corresponding trap will be sent. |
| 1.3.6.1.4.1.2011.10.2.75.8.1.5.1.5 | Columnh3cDot11RRMAdjChlIntfTrapThhd | read-write | current | Represents threshold of adjacent interference trap with current ap. If signal strength of the device exceeds this threshold, corresponding trap will be sent. |
| 1.3.6.1.4.1.2011.10.2.75.8.2 | Nodeh3cDot11RRMDetectGroup | |||
| 1.3.6.1.4.1.2011.10.2.75.8.2.1 | Tableh3cDot11RRMChlRptTable | not-accessible | current | This table shows the RRM channel information of each radio on all APs. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.1.1 | Rowh3cDot11RRMChlRptEntry | not-accessible | current | Each entry contains information of RRM channel information of the radio on the AP. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.1.1.1 | Columnh3cDot11RRMRadioIndex | accessible-for-notify | current | Represents index of the radio. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.1.1.2 | Columnh3cDot11RRMChlRptChlNum | accessible-for-notify | current | Channel number. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.1.1.3 | Columnh3cDot11RRMChlRptChlType | read-only | current | Channel type. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.1.1.4 | Columnh3cDot11RRMChlRptChlQlty | read-only | current | Channel quality. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.1.1.5 | Columnh3cDot11RRMChlRptNbrCnt | read-only | current | Number of neighbors found on the channel. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.1.1.6 | Columnh3cDot11RRMChlRptLoad | read-only | current | Load observed on the channel in percentage. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.1.1.7 | Columnh3cDot11RRMChlRptUtlz | read-only | current | Utilization of the channel in percentage. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.1.1.8 | Columnh3cDot11RRMChlRptIntrf | read-only | current | Interference observed on the channel in percentage. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.1.1.9 | Columnh3cDot11RRMChlRptPER | read-only | current | Packet error rate observed on the channel in percentage. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.1.1.10 | Columnh3cDot11RRMChlRptRetryRate | read-only | current | Percentage of retransmission happened on the channel. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.1.1.11 | Columnh3cDot11RRMChlRptNoise | read-only | current | Noise observed on the channel. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.1.1.12 | Columnh3cDot11RRMChlRptRadarIndtcr | read-write | current | Radar detection status. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.2 | Tableh3cDot11RRMNbrInfoTable | not-accessible | current | This table shows the RRM neighbor information of each radio on all APs. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.2.1 | Rowh3cDot11RRMNbrInfoEntry | not-accessible | current | Each entry contains information of RRM neighbor information of the radio on an AP. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.2.1.1 | Columnh3cDot11RrmNbrBSSID | not-accessible | current | MAC address of the AP. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.2.1.2 | Columnh3cDot11RrmNbrChl | read-only | current | Channel number on which the neighbor was found. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.2.1.3 | Columnh3cDot11RRMNbrIntrf | read-only | current | Interference observed on the channel in percentage by neighbor. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.2.1.4 | Columnh3cDot11RrmNbrRSSI | read-only | current | Signal strength of the AP in dBm. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.2.1.5 | Columnh3cDot11RrmNbrType | read-only | current | Type of the AP, managed or unmanaged. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.2.1.6 | Columnh3cDot11RrmNbrSSID | read-only | current | SSID of the Neighbor. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.2.1.7 | Columnh3cDot11RrmNbrSNR | read-only | current | Signal to noise ratio of the AP in dB. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.2.1.8 | Columnh3cDot11RrmNbrNF | read-only | current | Noise floor of the AP in dBm. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.3 | Tableh3cDot11RRMHistoryTable | not-accessible | current | This table shows the details of the latest three channel changes and power changes applied on all APs, including time of change, reason of the change and the c… |
| 1.3.6.1.4.1.2011.10.2.75.8.2.3.1 | Rowh3cDot11RRMHistoryEntry | not-accessible | current | Each entry shows the details of channel and power changes. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.3.1.1 | Columnh3cDot11RRMHistoryId | not-accessible | current | History number of the change. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.3.1.2 | Columnh3cDot11RRMHistoryRecIndctr | not-accessible | current | History record type of the change. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.3.1.3 | Columnh3cDot11RRMHistoryChl | read-only | current | Channel on which the radio operates before/after the change of channel or power. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.3.1.4 | Columnh3cDot11RRMHistoryPwr | read-only | current | Power of the radio before/after the change of channel or power. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.3.1.5 | Columnh3cDot11RRMHistoryLoad | read-only | current | Load observed on the radio in percentage before/after the change of channel or power. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.3.1.6 | Columnh3cDot11RRMHistoryUtlz | read-only | current | Utilization of the radio in percentage before/after the change of channel or power. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.3.1.7 | Columnh3cDot11RRMHistoryIntrf | read-only | current | Interference observed on the radio in percentage before/after the change of channel or power. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.3.1.8 | Columnh3cDot11RRMHistoryNoise | read-only | current | Noise observed on the radio before/after the change of channel or power. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.3.1.9 | Columnh3cDot11RRMHistoryPER | read-only | current | Packet error rate observed on the radio in percentage before/after the change of channel or power. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.3.1.10 | Columnh3cDot11RRMHistoryRetryRate | read-only | current | Percentage of retransmission happened on the radio before/after the change of channel or power. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.3.1.11 | Columnh3cDot11RRMHistoryChgReason | read-only | current | Reason for the change of channel or power. The various bit positions are: |0 |Others | |1 |Coverage | |2 |Radar | |3 |Retransmission | |4 |Packets discarded | … |
| 1.3.6.1.4.1.2011.10.2.75.8.2.3.1.12 | Columnh3cDot11RRMHistoryChgDateTime | read-only | current | The time when the channel or power change occurred. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.4 | Tableh3cDot11RRMRadioNbrInfoTable | not-accessible | current | This table shows the RRM neighbor information of each radio on all APs. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.4.1 | Rowh3cDot11RRMRadioNbrInfoEntry | not-accessible | current | Each entry contains information of RRM neighbor information of the radio on an AP. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.4.1.1 | Columnh3cDot11RRMRadioNbrAPID | not-accessible | current | AP serial id. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.4.1.2 | Columnh3cDot11RRMRadioNbrRadioID | not-accessible | current | Radio Id on AP. |
| 1.3.6.1.4.1.2011.10.2.75.8.2.4.1.3 | Columnh3cDot11RRMRadioNbrSSID | read-only | current | All neighbour SSIDs scanned by the selected radio. |
| 1.3.6.1.4.1.2011.10.2.75.8.3 | Nodeh3cDot11RRMNotifyGroup | |||
| 1.3.6.1.4.1.2011.10.2.75.8.3.1 | Nodeh3cDot11RRMChlQltyNotifications | |||
| 1.3.6.1.4.1.2011.10.2.75.8.3.1.0 | Nodeh3cDot11RRMChlQltyNtfPrefix | |||
| 1.3.6.1.4.1.2011.10.2.75.8.3.1.0.1 | Notificationh3cDot11RRMIntrfLimit | current | This notification will be sent when interference on the radio exceeds the limit. | |
| 1.3.6.1.4.1.2011.10.2.75.8.3.1.0.2 | Notificationh3cDot11RRMPERLimit | current | This notification will be sent when packet error rate on the radio exceeds the limit. | |
| 1.3.6.1.4.1.2011.10.2.75.8.3.1.0.3 | Notificationh3cDot11RRMNoiseLimit | current | This notification will be sent when noise on the radio exceeds the limit. | |
| 1.3.6.1.4.1.2011.10.2.75.8.3.2 | Nodeh3cDot11RRMResChgNotifications | |||
| 1.3.6.1.4.1.2011.10.2.75.8.3.2.0 | Nodeh3cDot11RRMResChgNtfPrefix | |||
| 1.3.6.1.4.1.2011.10.2.75.8.3.2.0.1 | Notificationh3cDot11RRMPowerChange | current | This notification will be sent when power changed on the radio automatically. | |
| 1.3.6.1.4.1.2011.10.2.75.8.3.3 | Nodeh3cDot11RRMNotificationsVar | |||
| 1.3.6.1.4.1.2011.10.2.75.8.3.3.1 | Scalarh3cDot11NewPower | accessible-for-notify | current | Power of the radio after the change of power. |
| 1.3.6.1.4.1.2011.10.2.75.8.3.3.2 | Scalarh3cDot11OldPower | accessible-for-notify | current | Power of the radio before the change of power. |
| 1.3.6.1.4.1.2011.10.2.75.8.4 | Nodeh3cDot11MonitorDetectedGroup | |||
| 1.3.6.1.4.1.2011.10.2.75.8.4.1 | Tableh3cDot11MonitorDetectedDevTable | not-accessible | current | This table shows the devices of AP detected |
| 1.3.6.1.4.1.2011.10.2.75.8.4.1.1 | Rowh3cDot11MonitorDetectedDevEntry | not-accessible | current | Each entry contains information of detected devices. |
| 1.3.6.1.4.1.2011.10.2.75.8.4.1.1.1 | Columnh3cDot11MonitorDevMAC | not-accessible | current | Represents MAC address of the device detected. |
| 1.3.6.1.4.1.2011.10.2.75.8.4.1.1.2 | Columnh3cDot11MonitorDevType | read-only | current | Represents type of the device detected. |
| 1.3.6.1.4.1.2011.10.2.75.8.4.1.1.3 | Columnh3cDot11MonitorDevVendor | read-only | current | Represents vendor of the detected device. |
| 1.3.6.1.4.1.2011.10.2.75.8.4.1.1.4 | Columnh3cDot11MonitorDevSSID | read-only | current | Represents the service set identifier for the ESS of the device which type is ap or adhoc. |
| 1.3.6.1.4.1.2011.10.2.75.8.4.1.1.5 | Columnh3cDot11MonitorDevBSSID | read-only | current | Represents the basic service set identifier of the detected device. |
| 1.3.6.1.4.1.2011.10.2.75.8.4.1.1.6 | Columnh3cDot11MonitorDevChannel | read-only | current | Represents the channel in which the device was last detected. AP will choose the channel which has maximum signal strength as effective channel, as there is in… |
| 1.3.6.1.4.1.2011.10.2.75.8.4.1.1.7 | Columnh3cDot11MonitorRadioId | read-only | current | Represents the radio ID of the AP that detected the device. |
| 1.3.6.1.4.1.2011.10.2.75.8.4.1.1.8 | Columnh3cDot11MonitorDevMaxRSSI | read-only | current | Represents the maximum detected RSSI of the device in a scan report cycle. |
| 1.3.6.1.4.1.2011.10.2.75.8.4.1.1.9 | Columnh3cDot11MonitorDevBeaconIntvl | read-only | current | Represents the beacon interval for the detected device(not include the device which type is client). |
| 1.3.6.1.4.1.2011.10.2.75.8.4.1.1.10 | Columnh3cDot11MonitorDevFstDctTime | read-only | current | Represents the time at which the device was first detected. |
| 1.3.6.1.4.1.2011.10.2.75.8.4.1.1.11 | Columnh3cDot11MonitorDevLstDctTime | read-only | current | Represents the time at which the device was detected last time. |
| 1.3.6.1.4.1.2011.10.2.75.8.4.1.1.12 | Columnh3cDot11MonitorDevClear | read-write | current | This object is used to clear the information of the device detected in the WLAN. It will return false for get operation. |
| 1.3.6.1.4.1.2011.10.2.75.8.4.1.1.13 | Columnh3cDot11MonitorDevSNR | read-only | current | Represents the SNR of the device in a scan report cycle. |