HM2-NETCONFIG-MIB
86 objects
Hirschmann Network Configuration MIB. Copyright (C) 2012. All Rights Reserved.
Imported Objects
| HM2-TC-MIB | hm2ConfigurationMibs HmEnabledStatus |
| IF-MIB | ifIndex InterfaceIndex |
| INET-ADDRESS-MIB | InetAddress InetAddressPrefixLength InetAddressType |
| IP-MIB | IpAddressOriginTC |
| RMON2-MIB | TimeFilter |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString MacAddress RowStatus TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.248.11.20 | Identityhm2NetConfigMib | Hirschmann Network Configuration MIB. Copyright (C) 2012. All Rights Reserved. | ||
| 1.3.6.1.4.1.248.11.20.0 | Nodehm2NetConfigMibNotifications | |||
| 1.3.6.1.4.1.248.11.20.0.1 | Notificationhm2NetACDNotification | current | This trap reports an address conflict. | |
| 1.3.6.1.4.1.248.11.20.0.2 | Notificationhm2NetMacACDNotification | current | This trap reports a MAC address conflict with it's own MAC address. | |
| 1.3.6.1.4.1.248.11.20.1 | Nodehm2NetConfigMibObjects | |||
| 1.3.6.1.4.1.248.11.20.1.1 | Nodehm2NetStaticGroup | |||
| 1.3.6.1.4.1.248.11.20.1.1.1 | Scalarhm2NetConfigProtocol | read-write | current | The switch's network configuration protocol. The default value is dependent of the device type. |
| 1.3.6.1.4.1.248.11.20.1.1.2 | Scalarhm2NetLocalIPAddrType | read-write | current | Local IP address type. |
| 1.3.6.1.4.1.248.11.20.1.1.3 | Scalarhm2NetLocalIPAddr | read-write | current | IP address of the management agent board. Changing this value will take effect after activating with hm2NetAction. |
| 1.3.6.1.4.1.248.11.20.1.1.4 | Scalarhm2NetPrefixLength | read-write | current | The length of the IP netmask. |
| 1.3.6.1.4.1.248.11.20.1.1.5 | Scalarhm2NetGatewayIPAddrType | read-write | current | Default gateway IP address type. |
| 1.3.6.1.4.1.248.11.20.1.1.6 | Scalarhm2NetGatewayIPAddr | read-write | current | IP address of the default gateway. Changing this value will take effect after activating with hm2NetAction. |
| 1.3.6.1.4.1.248.11.20.1.1.7 | Scalarhm2NetVlanID | read-write | current | VLAN-ID of the IP protocol stack. The VLAN-ID value means that only traffic of the appropriate VLAN is accepted and outgoing traffic uses this VLAN-ID. |
| 1.3.6.1.4.1.248.11.20.1.1.8 | Scalarhm2NetVlanPriority | read-write | current | VLAN Priority which is used in management replies. |
| 1.3.6.1.4.1.248.11.20.1.1.9 | Scalarhm2NetIpDscpPriority | read-write | current | IP DSCP value which is used in management replies. |
| 1.3.6.1.4.1.248.11.20.1.1.10 | Scalarhm2NetMgmtPort | read-write | current | The port number of the Ethernet port, which gets the access to the switch management. If the value is set to 0, the access to the switch management is permitte… |
| 1.3.6.1.4.1.248.11.20.1.1.11 | Scalarhm2NetDHCPClientId | read-only | current | The identifier string that is currently used by the client in the request packets to the server for obtaining lease information. |
| 1.3.6.1.4.1.248.11.20.1.1.20 | Scalarhm2NetDHCPClientConfigLoad | read-write | current | Enables/disables the DHCP options 4/42 (time servers) and 66/67 (Load config over TFTP on boot) on DHCP/BOOTP client. |
| 1.3.6.1.4.1.248.11.20.1.1.21 | Scalarhm2NetDHCPClientLeaseTime | read-only | current | Displays the remaining lease of the management IP time in seconds. |
| 1.3.6.1.4.1.248.11.20.1.1.30 | Scalarhm2NetIPv6AdminStatus | read-write | current | Enable/Disable IPv6 feature. A (1) enables, a (2) disables. |
| 1.3.6.1.4.1.248.11.20.1.1.31 | Scalarhm2NetIPv6ConfigProtocol | read-write | current | The switch's network IPv6 configuration protocol. |
| 1.3.6.1.4.1.248.11.20.1.1.32 | Scalarhm2NetIPv6GatewayAddrType | read-write | current | Default gateway IPv6 address type. |
| 1.3.6.1.4.1.248.11.20.1.1.33 | Scalarhm2NetIPv6GatewayAddr | read-write | current | IPv6 address of the default gateway. |
| 1.3.6.1.4.1.248.11.20.1.1.34 | Scalarhm2NetIPv6DupAddrDetectTrans | read-write | current | Number of Neighbor Solicitations for DAD mechanism. |
| 1.3.6.1.4.1.248.11.20.1.1.35 | Scalarhm2NetIPv6DHCPClientId | read-only | current | The identifier string that is currently used by the client in the IPv6 implementation to request packets to the server to obtain lease information. |
| 1.3.6.1.4.1.248.11.20.1.1.36 | Tablehm2NetIPv6LocalAddrTable | not-accessible | current | The list of IPv6 addresses and their prefixes for the network port. |
| 1.3.6.1.4.1.248.11.20.1.1.36.1 | Rowhm2NetIPv6LocalAddrEntry | not-accessible | current | An interface entry containing objects of a particular IPv6 address prefix |
| 1.3.6.1.4.1.248.11.20.1.1.36.1.1 | Columnhm2NetIPv6LocalAddrPrefixType | not-accessible | current | The management IPv6 prefix type |
| 1.3.6.1.4.1.248.11.20.1.1.36.1.2 | Columnhm2NetIPv6LocalAddrPrefix | not-accessible | current | IPv6 prefix of the management agent board. |
| 1.3.6.1.4.1.248.11.20.1.1.36.1.3 | Columnhm2NetIPv6LocalAddrPrefixLength | not-accessible | current | The management IPv6 address prefix length. |
| 1.3.6.1.4.1.248.11.20.1.1.36.1.4 | Columnhm2NetIPv6LocalAddrType | read-write | current | The management IPv6 address type |
| 1.3.6.1.4.1.248.11.20.1.1.36.1.5 | Columnhm2NetIPv6LocalAddr | read-write | current | IPv6 address of the management agent board. |
| 1.3.6.1.4.1.248.11.20.1.1.36.1.6 | Columnhm2NetIPv6LocalAddrEuiFlag | read-write | current | The management IPv6 EUI flag. |
| 1.3.6.1.4.1.248.11.20.1.1.36.1.7 | Columnhm2NetIPv6LocalAddrOrigin | read-write | current | Origin of IPv6 address. |
| 1.3.6.1.4.1.248.11.20.1.1.36.1.8 | Columnhm2NetIPv6LocalAddrStatus | read-create | current | |
| 1.3.6.1.4.1.248.11.20.1.1.50 | Scalarhm2NetAction | read-write | current | This object, when read, always returns a value of other(1). Setting the object to activate(2) causes a reconfiguration of the IP protocol stack with the curren… |
| 1.3.6.1.4.1.248.11.20.1.2 | Nodehm2NetACDGroup | |||
| 1.3.6.1.4.1.248.11.20.1.2.1 | Scalarhm2NetACDStatus | read-write | current | Sets the status of the ip address conflict detection mechanism on this device. With activating the ACD status an internal check of duplicated IP-addresses is e… |
| 1.3.6.1.4.1.248.11.20.1.2.2 | Scalarhm2NetACDDetectionMode | read-write | current | Sets the mode of the ip address conflict detection mechanism on this device. activeAndPassive (1): Both active and passive detection are active. activeDetectio… |
| 1.3.6.1.4.1.248.11.20.1.2.3 | Scalarhm2NetACDOngoingProbeStatus | read-write | current | If enabled, the device sends periodic ARP or NDP probes every 90-120 seconds. |
| 1.3.6.1.4.1.248.11.20.1.2.5 | Scalarhm2NetACDDelay | read-write | current | Time gap between ARP or NDP probes being sent. |
| 1.3.6.1.4.1.248.11.20.1.2.7 | Scalarhm2NetACDReleaseDelay | read-write | current | Delay in seconds to the next ARP or NDP probe cycle after an ip address conflict was detected. |
| 1.3.6.1.4.1.248.11.20.1.2.9 | Scalarhm2NetACDMaxProtection | read-write | current | The number of ARP announcement packets (gratuitous ARP packets) in passive(ongoing) mode to be received within hm2NetACDProtectInterval until the agent detects… |
| 1.3.6.1.4.1.248.11.20.1.2.11 | Scalarhm2NetACDProtectInterval | read-write | current | Delay in milliseconds between two protections. See also hm2NetACDMaxProtection. |
| 1.3.6.1.4.1.248.11.20.1.2.13 | Scalarhm2NetACDFaultState | read-only | current | true(1) if an active address conflict is detected. false(2) if no present address conflict. |
| 1.3.6.1.4.1.248.11.20.1.2.15 | Scalarhm2NetACDTrapEnable | read-write | current | If enabled this trap reports an address conflict. |
| 1.3.6.1.4.1.248.11.20.1.2.20 | Tablehm2NetACDAddrTable | not-accessible | current | This table contains address conflict detection information on the local system known to this agent. |
| 1.3.6.1.4.1.248.11.20.1.2.20.1 | Rowhm2NetACDAddrEntry | not-accessible | current | IP Address conflict detection information about a particular address on the local system known to this agent. There may be multiple addresses configured on the… |
| 1.3.6.1.4.1.248.11.20.1.2.20.1.1 | Columnhm2NetACDTimeMark | read-only | current | A TimeFilter for this entry. See the TimeFilter textual convention in IETF RFC 2021 and http://www.ietf.org/IESG/Implementations/RFC2021-Implementation.txt to … |
| 1.3.6.1.4.1.248.11.20.1.2.20.1.3 | Columnhm2NetACDAddrType | read-only | current | Local IP Address Type |
| 1.3.6.1.4.1.248.11.20.1.2.20.1.5 | Columnhm2NetACDIPAddr | read-only | current | IP address used to identify the management address component associated with the local system. |
| 1.3.6.1.4.1.248.11.20.1.2.20.1.7 | Columnhm2NetACDMAC | read-only | current | The physical address of the device that was detected causing the ip address conflict. |
| 1.3.6.1.4.1.248.11.20.1.2.20.1.9 | Columnhm2NetACDifIndex | read-only | current | The interface index on the local system where the ip address conflict was detected. |
| 1.3.6.1.4.1.248.11.20.1.3 | Nodehm2NetMacGroup | |||
| 1.3.6.1.4.1.248.11.20.1.3.1 | Scalarhm2NetLocalBurnedInMacAddr | read-only | current | Physical base address (MAC address) of the agent. This is the burned in MAC address from the production |
| 1.3.6.1.4.1.248.11.20.1.3.2 | Scalarhm2NetLocalAdminMacAddress | read-write | current | The switch's network locally administered MAC address. This is the locally MAC address from the administrator. If the hm2NetLocalAdminMacAddress is nonzero, th… |
| 1.3.6.1.4.1.248.11.20.1.3.3 | Scalarhm2NetMacAddressType | read-only | current | Shows the currently used MAC address at boot time. The device starts with the burned in MAC address when hm2NetLocalAdminMacAddress is zero, otherwise with the… |
| 1.3.6.1.4.1.248.11.20.1.4 | Nodehm2NetHiDiscoveryGroup | |||
| 1.3.6.1.4.1.248.11.20.1.4.1 | Scalarhm2NetHiDiscoveryOperation | read-write | current | Enables/disables the HiDiscovery protocol on this device. This protocol allows a remote host to detect devices without an IP configuration. It also allows the … |
| 1.3.6.1.4.1.248.11.20.1.4.2 | Scalarhm2NetHiDiscoveryMode | read-write | current | In the read only mode only detecting and reading the IP parameters is permitted. The read write mode gives full access to the device. |
| 1.3.6.1.4.1.248.11.20.1.4.3 | Scalarhm2NetHiDiscoveryBlinking | read-write | current | Enables/disables the HiDiscovery blinking sequence on this device. This object will not be saved. |
| 1.3.6.1.4.1.248.11.20.1.4.4 | Scalarhm2NetHiDiscoveryProtocol | read-only | current | Shows the HiDiscovery protocols supported by the device. |
| 1.3.6.1.4.1.248.11.20.1.4.5 | Scalarhm2NetHiDiscoveryRelay | read-write | current | Relay/bridge HiDiscovery frames. |
| 1.3.6.1.4.1.248.11.20.1.5 | Nodehm2NetMacACDGroup | |||
| 1.3.6.1.4.1.248.11.20.1.5.1 | Scalarhm2NetMacACDStatus | read-write | current | Sets the status of the MAC address conflict detection mechanism on this device. |
| 1.3.6.1.4.1.248.11.20.1.5.2 | Scalarhm2NetMacACDConflictAddress | read-only | current | MAC address in case of a conflict. |
| 1.3.6.1.4.1.248.11.20.1.6 | Nodehm2NetOobMgmtGroup | |||
| 1.3.6.1.4.1.248.11.20.1.6.1 | Scalarhm2NetOobMgmtAdminState | read-write | current | The status of the Out-of-band management on this device. |
| 1.3.6.1.4.1.248.11.20.1.6.2 | Scalarhm2NetOobMgmtProtocol | read-write | current | The switch's out-of-band network configuration protocol. The default value is dependent of the device type. |
| 1.3.6.1.4.1.248.11.20.1.6.3 | Scalarhm2NetOobMgmtIPAddrType | read-write | current | Out-of-band IP address type. |
| 1.3.6.1.4.1.248.11.20.1.6.4 | Scalarhm2NetOobMgmtIPAddr | read-write | current | Out-of-band IP address of the management agent board. Changing this value will take effect after activating with hm2NetOobMgmtAction. |
| 1.3.6.1.4.1.248.11.20.1.6.5 | Scalarhm2NetOobMgmtPrefixLength | read-write | current | The length of the IP netmask. |
| 1.3.6.1.4.1.248.11.20.1.6.6 | Scalarhm2NetOobMgmtGatewayIPAddrType | read-write | current | Out-of-band default gateway IP address type. |
| 1.3.6.1.4.1.248.11.20.1.6.7 | Scalarhm2NetOobMgmtGatewayIPAddr | read-write | current | Out-of-band IP address of the default gateway. Changing this value will take effect after activating with hm2NetOobMgmtAction. |
| 1.3.6.1.4.1.248.11.20.1.6.8 | Scalarhm2NetOobMgmtMacAddress | read-only | current | Out-of-band MAC address of the interface. |
| 1.3.6.1.4.1.248.11.20.1.6.9 | Scalarhm2NetOobMgmtOperState | read-only | current | Out-of-band interface current operational state. |
| 1.3.6.1.4.1.248.11.20.1.6.10 | Scalarhm2NetOobMgmtDHCPClientLeaseTime | read-only | current | Displays the remaining lease of the management(OOB) IP time in seconds. |
| 1.3.6.1.4.1.248.11.20.1.6.50 | Scalarhm2NetOobMgmtAction | read-write | current | This object, when read, always returns a value of other(1). Setting the object to activate(2) causes a reconfiguration of the out-of-band IP protocol stack wit… |
| 1.3.6.1.4.1.248.11.20.1.7 | Nodehm2NetOobUsbMgmtGroup | |||
| 1.3.6.1.4.1.248.11.20.1.7.1 | Scalarhm2NetOobUsbMgmtAdminState | read-write | current | The status of the USB Out-of-band management on this device. |
| 1.3.6.1.4.1.248.11.20.1.7.3 | Scalarhm2NetOobUsbMgmtIPAddrType | read-write | current | USB Out-of-band Device IP address type. |
| 1.3.6.1.4.1.248.11.20.1.7.4 | Scalarhm2NetOobUsbMgmtIPAddr | read-write | current | USB Out-of-band device IP address. Changing this value will take effect after activating with hm2NetOobUsbMgmtAction. |
| 1.3.6.1.4.1.248.11.20.1.7.5 | Scalarhm2NetOobUsbMgmtPrefixLength | read-write | current | The length of the IP netmask. |
| 1.3.6.1.4.1.248.11.20.1.7.7 | Scalarhm2NetOobUsbMgmtHostMacAddress | read-only | current | USB Out-of-band MAC address of the host interface. |
| 1.3.6.1.4.1.248.11.20.1.7.8 | Scalarhm2NetOobUsbMgmtDeviceMacAddress | read-only | current | USB Out-of-band MAC address of the device interface. |
| 1.3.6.1.4.1.248.11.20.1.7.50 | Scalarhm2NetOobUsbMgmtAction | read-write | current | This object, when read, always returns a value of other(1). Setting the object to activate(2) causes a reconfiguration of the USB out-of-band IP protocol stack… |