HM2-PLATFORM-SWITCHING-MIB
568 objects
The Hirschmann Private Platform2 MIB for Layer2 Switching. Copyright (C) 2011. All Rights Reserved.
Imported Objects
| BRIDGE-MIB | dot1dBasePortEntry |
| HM2-TC-MIB | hm2PlatformMibs HmEnabledStatus |
| IF-MIB | ifIndex InterfaceIndex InterfaceIndexOrZero |
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| P-BRIDGE-MIB | dot1dPortGmrpEntry |
| Q-BRIDGE-MIB | dot1qFdbId dot1qPortVlanEntry dot1qVlanIndex PortList VlanId VlanIdOrNone VlanIndex |
| SNMPv2-SMI | Counter32 Gauge32 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-IDENTITY OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | DateAndTime DisplayString MacAddress RowStatus TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.248.12.1 | Identityhm2PlatformSwitching | The Hirschmann Private Platform2 MIB for Layer2 Switching. Copyright (C) 2011. All Rights Reserved. | ||
| 1.3.6.1.4.1.248.12.1.0 | Nodehm2PlatformSwitchingTraps | |||
| 1.3.6.1.4.1.248.12.1.0.10 | Notificationhm2PlatformStpInstanceNewRootTrap | current | Trap is sent when this machine is a new STP Root when there is more than one STP instance. | |
| 1.3.6.1.4.1.248.12.1.0.11 | Notificationhm2PlatformStpInstanceTopologyChangeTrap | current | Trap is sent when there is a STP topology change when there is more than one STP instance. | |
| 1.3.6.1.4.1.248.12.1.0.15 | Notificationhm2PlatformDaiIntfErrorDisabledTrap | current | Trap is sent once an interface is error disabled by DAI when the incoming packet rate exceeded configured rate limit during a burst-interval. | |
| 1.3.6.1.4.1.248.12.1.0.16 | Notificationhm2PlatformStpInstanceLoopInconsistentStartTrap | current | Trap is sent when this port in this STP instance enters loop inconsistent state upon failure to receive a BPDU. | |
| 1.3.6.1.4.1.248.12.1.0.17 | Notificationhm2PlatformStpInstanceLoopInconsistentEndTrap | current | Trap is sent when this port in this STP instance exits loop inconsistent state upon reception of a BPDU. | |
| 1.3.6.1.4.1.248.12.1.0.18 | Notificationhm2PlatformDhcpSnoopingIntfErrorDisabledTrap | current | Trap is sent once an interface is error disabled by DHCP Snooping when the incoming packet rate exceeded configured rate limit during a burst-interval. | |
| 1.3.6.1.4.1.248.12.1.0.20 | Notificationhm2AgentSwitchIpAddressConflictTrap | current | IP address conflict trap signifies the reception of an ARP from another host in the LAN that has conflicting IP address. | |
| 1.3.6.1.4.1.248.12.1.0.32 | Notificationhm2AgentSwitchLoopProtectionTrap | current | Trap is sent on detection of loop on an interface. | |
| 1.3.6.1.4.1.248.12.1.0.248 | Notificationhm2PlatformStpCstBpduGuardTrap | current | This trap is sent if on this port when the BPDU guard functionality is enabled (globally and for this port) and a (R)STP BPDU is received on this port. That me… | |
| 1.3.6.1.4.1.248.12.1.2 | Nodehm2AgentConfigGroup | |||
| 1.3.6.1.4.1.248.12.1.2.2 | Nodehm2AgentLagConfigGroup | |||
| 1.3.6.1.4.1.248.12.1.2.2.1 | Scalarhm2AgentLagConfigCreate | read-write | current | Agent LAG Create. When this object is set with a non-empty string with the format lag/<port>, a new LAG will be created if possible, with the entered string as… |
| 1.3.6.1.4.1.248.12.1.2.2.2 | Tablehm2AgentLagSummaryConfigTable | not-accessible | current | A summary table of the switch's LAG config entries |
| 1.3.6.1.4.1.248.12.1.2.2.2.1 | Rowhm2AgentLagSummaryConfigEntry | not-accessible | current | Switch's LAG config entry |
| 1.3.6.1.4.1.248.12.1.2.2.2.1.1 | Columnhm2AgentLagSummaryLagIndex | read-only | current | Agent LAG IfIndex. This value corresponds with the LAG interface in the ifTable. |
| 1.3.6.1.4.1.248.12.1.2.2.2.1.2 | Columnhm2AgentLagSummaryName | read-create | current | Agent LAG Name. The associated name of the LAG used during creation. |
| 1.3.6.1.4.1.248.12.1.2.2.2.1.3 | Columnhm2AgentLagSummaryFlushTimer | read-create | obsolete | Agent LAG FlushTimer. |
| 1.3.6.1.4.1.248.12.1.2.2.2.1.4 | Columnhm2AgentLagSummaryLinkTrap | read-create | current | Agent LAG LinkTrap. Configures sending Link Up/Down traps when the LAG interface goes Up or Down. |
| 1.3.6.1.4.1.248.12.1.2.2.2.1.5 | Columnhm2AgentLagSummaryAdminMode | read-create | current | Agent LAG AdminMode. Administratively enables or disables this LAG interface. |
| 1.3.6.1.4.1.248.12.1.2.2.2.1.6 | Columnhm2AgentLagSummaryStpMode | read-create | current | Agent LAG StpMode Administratively enables or disables STP on this interface. |
| 1.3.6.1.4.1.248.12.1.2.2.2.1.7 | Columnhm2AgentLagSummaryAddPort | read-create | current | Agent LAG AddPort. Set to a non 0 value to add a port to the LAG. Values correspond to ifIndex values in the ifTable. Note: agentPortType for the port to be ad… |
| 1.3.6.1.4.1.248.12.1.2.2.2.1.8 | Columnhm2AgentLagSummaryDeletePort | read-create | current | Agent LAG DeletePort. Set to a non 0 value to remove a port from the LAG. Values correspond to ifIndex values in the ifTable. |
| 1.3.6.1.4.1.248.12.1.2.2.2.1.9 | Columnhm2AgentLagSummaryStatus | read-create | current | Agent LAG Status. active(1) - This LAG is enabled. destroy(6) - Set to this value to remove the LAG. |
| 1.3.6.1.4.1.248.12.1.2.2.2.1.10 | Columnhm2AgentLagSummaryType | read-only | current | Agent LAG Type. static(1) - This LAG is staticly maintained. dynamic(2) - This LAG is dynamicly maintained. |
| 1.3.6.1.4.1.248.12.1.2.2.2.1.11 | Columnhm2AgentLagSummaryStaticCapability | read-create | current | Agent LAG Static Capability enable(1) - Static capability is enabled for this LAG interface disable(2) - Static capability is disabled for this LAG interface |
| 1.3.6.1.4.1.248.12.1.2.2.2.1.12 | Columnhm2AgentLagSummaryHashOption | read-create | current | LAG Hashing Option. Valid values correspond to 1 (=Source MAC, VLAN, EtherType, and incoming port associated with the packet) 2 (=Destination MAC, VLAN, EtherT… |
| 1.3.6.1.4.1.248.12.1.2.2.2.1.13 | Columnhm2AgentLagSummaryMinimumActiveLinks | read-create | current | Agent LAG Threshold. This configures the threshold(i.e minimum number of active ports) value for trunk port . |
| 1.3.6.1.4.1.248.12.1.2.2.2.1.248 | Columnhm2AgentLagSummaryMaxFrameSizeLimit | read-only | current | This object identifies the largest value that can be configured for hm2AgentLagSummaryMaxFrameSize. |
| 1.3.6.1.4.1.248.12.1.2.2.2.1.249 | Columnhm2AgentLagSummaryMaxFrameSize | read-create | current | This object identifies the currently configured maximum frame size value for this port. The maximum value that this object can be set to is the value of hm2Age… |
| 1.3.6.1.4.1.248.12.1.2.2.3 | Tablehm2AgentLagDetailedConfigTable | not-accessible | current | A detailed table of the switch's LAG config entries |
| 1.3.6.1.4.1.248.12.1.2.2.3.1 | Rowhm2AgentLagDetailedConfigEntry | not-accessible | current | Switch's LAG config entry |
| 1.3.6.1.4.1.248.12.1.2.2.3.1.1 | Columnhm2AgentLagDetailedLagIndex | read-only | current | LAG index |
| 1.3.6.1.4.1.248.12.1.2.2.3.1.2 | Columnhm2AgentLagDetailedIfIndex | read-only | current | LAG port index |
| 1.3.6.1.4.1.248.12.1.2.2.3.1.3 | Columnhm2AgentLagDetailedPortSpeed | read-only | current | LAG port speed. See agentPortType for a description and list of valid values. |
| 1.3.6.1.4.1.248.12.1.2.2.3.1.4 | Columnhm2AgentLagDetailedPortStatus | read-only | current | LAG port status. active(1) - Actively participating in the LAG. inactive(2) - Not participating in the LAG. |
| 1.3.6.1.4.1.248.12.1.2.2.4 | Scalarhm2AgentLagConfigStaticCapability | read-write | obsolete | Agent LAG Static Capability. Configures whether Static LAGs are supported on this device. |
| 1.3.6.1.4.1.248.12.1.2.2.5 | Scalarhm2AgentLagConfigGroupHashOption | read-write | current | LAG Hashing Option. Valid values correspond to 1 (=Source MAC, VLAN, EtherType, and incoming port associated with the packet) 2 (=Destination MAC, VLAN, EtherT… |
| 1.3.6.1.4.1.248.12.1.2.2.248 | Scalarhm2AgentLagConfigGroupMaxNumPortsPerLag | read-only | current | The maximum number of ports per LAG supported on this device. |
| 1.3.6.1.4.1.248.12.1.2.2.249 | Scalarhm2AgentLagConfigGroupMaxNumOfLags | read-only | current | The maximum number of LAGs this device supports. |
| 1.3.6.1.4.1.248.12.1.2.2.250 | Scalarhm2AgentLagConfigGroupNumOfLagsConfigured | read-only | current | The number of LAGs currently configured on this device. |
| 1.3.6.1.4.1.248.12.1.2.2.251 | Scalarhm2AgentLagConfigGroupLagsConfigured | read-only | current | The LAGs currently configured on the device. |
| 1.3.6.1.4.1.248.12.1.2.2.260 | Nodehm2AgentLagConfigSNMPExtensionGroup | |||
| 1.3.6.1.4.1.248.12.1.2.2.260.1 | Identityhm2AgentLagConfigGroupPortIsLagMemberErrorReturn | current | Indicates that the port is unavailable for current setting because it is a LAG member. | |
| 1.3.6.1.4.1.248.12.1.2.2.260.2 | Identityhm2AgentLagMirrorProbePortLagMemberErrorReturn | current | The port cannot be added because it is already a probe port. | |
| 1.3.6.1.4.1.248.12.1.2.2.260.3 | Identityhm2AgentLagMirrorPrivateVLANLagMemberErrorReturn | current | A port which is member of a private VLAN cannot be assigned to the LAG interface. | |
| 1.3.6.1.4.1.248.12.1.2.2.260.4 | Identityhm2AgentLagMirrorRCPLagMemberErrorReturn | current | A port which is used in RCP cannot be assigned to the LAG interface. | |
| 1.3.6.1.4.1.248.12.1.2.2.260.5 | Identityhm2AgentLagMirrorLagAddPortMemberErrorReturn | current | The port cannot be assigned to the LAG interface because the port takes part in a port mirroring. | |
| 1.3.6.1.4.1.248.12.1.2.8 | Nodehm2AgentSwitchConfigGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.4 | Tablehm2AgentSwitchAddressAgingTimeoutTable | not-accessible | current | The switch's address aging timeout table |
| 1.3.6.1.4.1.248.12.1.2.8.4.1 | Rowhm2AgentSwitchAddressAgingTimeoutEntry | not-accessible | current | Aging information about a specific Filtering Database. |
| 1.3.6.1.4.1.248.12.1.2.8.4.1.1 | Columnhm2AgentSwitchAddressAgingTimeout | read-write | current | The FDB entry's address aging timeout (in seconds) |
| 1.3.6.1.4.1.248.12.1.2.8.5 | Tablehm2AgentSwitchStaticMacFilteringTable | not-accessible | current | The switch's static Mac filtering table |
| 1.3.6.1.4.1.248.12.1.2.8.5.1 | Rowhm2AgentSwitchStaticMacFilteringEntry | not-accessible | current | Per port ingress/egress filter configuration based on VLAN Id and MAC address. |
| 1.3.6.1.4.1.248.12.1.2.8.5.1.1 | Columnhm2AgentSwitchStaticMacFilteringVlanId | read-only | current | The Static MAC Filter Vlan Id |
| 1.3.6.1.4.1.248.12.1.2.8.5.1.2 | Columnhm2AgentSwitchStaticMacFilteringAddress | read-only | current | The Static MAC Filter MAC address |
| 1.3.6.1.4.1.248.12.1.2.8.5.1.3 | Columnhm2AgentSwitchStaticMacFilteringSourcePortMask | read-write | current | The Static MAC Filter source port mask. When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Con… |
| 1.3.6.1.4.1.248.12.1.2.8.5.1.4 | Columnhm2AgentSwitchStaticMacFilteringDestPortMask | read-write | current | The Static MAC Filter destination port mask. When setting this value, the system will ignore configuration for ports not between the first and last valid ports… |
| 1.3.6.1.4.1.248.12.1.2.8.5.1.5 | Columnhm2AgentSwitchStaticMacFilteringStatus | read-create | current | The Static MAC Filter status. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry |
| 1.3.6.1.4.1.248.12.1.2.8.6 | Nodehm2AgentSwitchSnoopingGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.6.1 | Tablehm2AgentSwitchSnoopingCfgTable | not-accessible | current | A table of the IGMP/MLD Snooping Global configuration entries. |
| 1.3.6.1.4.1.248.12.1.2.8.6.1.1 | Rowhm2AgentSwitchSnoopingCfgEntry | not-accessible | current | Represents entry for Snooping switch Configuration. |
| 1.3.6.1.4.1.248.12.1.2.8.6.1.1.1 | Columnhm2AgentSwitchSnoopingProtocol | read-only | current | The protocol type of network protocol in use. |
| 1.3.6.1.4.1.248.12.1.2.8.6.1.1.2 | Columnhm2AgentSwitchSnoopingAdminMode | read-write | current | This enables or disables Snooping on the system. |
| 1.3.6.1.4.1.248.12.1.2.8.6.1.1.3 | Columnhm2AgentSwitchSnoopingPortMask | read-write | current | IGMP/MLD Snooping Port Mask. This allows configuration of IGMP/MLD Snooping on selected ports. IGMP/MLD Snooping cannot be enabled on an interface that has rou… |
| 1.3.6.1.4.1.248.12.1.2.8.6.1.1.4 | Columnhm2AgentSwitchSnoopingMulticastControlFramesProcessed | read-only | current | Multicast Control Frames Processed by CPU. The number of multicast control frames that have been processed by the CPU. |
| 1.3.6.1.4.1.248.12.1.2.8.7 | Nodehm2AgentSwitchSnoopingIntfGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.7.1 | Tablehm2AgentSwitchSnoopingIntfTable | not-accessible | current | A table of the IGMP/MLD Snooping Interface configuration entries. |
| 1.3.6.1.4.1.248.12.1.2.8.7.1.1 | Rowhm2AgentSwitchSnoopingIntfEntry | not-accessible | current | Represents entry for a IGMP/MLD Snooping Interface. |
| 1.3.6.1.4.1.248.12.1.2.8.7.1.1.1 | Columnhm2AgentSwitchSnoopingIntfIndex | read-only | current | The port number to be selected. Each port maps to an interface. |
| 1.3.6.1.4.1.248.12.1.2.8.7.1.1.2 | Columnhm2AgentSwitchSnoopingIntfAdminMode | read-write | current | This enables or disables IGMP/MLD Snooping on a selected interface. |
| 1.3.6.1.4.1.248.12.1.2.8.7.1.1.3 | Columnhm2AgentSwitchSnoopingIntfGroupMembershipInterval | read-write | current | The amount of time in seconds that a switch will wait for a report from a particular group on the selected interface before deleting the interface from the ent… |
| 1.3.6.1.4.1.248.12.1.2.8.7.1.1.4 | Columnhm2AgentSwitchSnoopingIntfMaxResponseTime | read-write | current | The amount of time in seconds a switch will wait after sending a query on the selected interface because it did not receive a report for a particular group in … |
| 1.3.6.1.4.1.248.12.1.2.8.7.1.1.5 | Columnhm2AgentSwitchSnoopingIntfMRPExpirationTime | read-write | current | The amount of time in seconds that a switch will wait for a query to be received on the selected interface before the interface is removed from the list of int… |
| 1.3.6.1.4.1.248.12.1.2.8.7.1.1.6 | Columnhm2AgentSwitchSnoopingIntfFastLeaveAdminMode | read-write | current | This enables or disables IGMP/MLD Snooping on the selected interface. |
| 1.3.6.1.4.1.248.12.1.2.8.7.1.1.7 | Columnhm2AgentSwitchSnoopingIntfMulticastRouterMode | read-write | current | The port explicitly configured by management to be IGMP query port for all VLANs. |
| 1.3.6.1.4.1.248.12.1.2.8.7.1.1.8 | Columnhm2AgentSwitchSnoopingIntfVlanIDs | read-only | current | This field lists all the VlanIDs which include the selected interface. |
| 1.3.6.1.4.1.248.12.1.2.8.8 | Nodehm2AgentSwitchSnoopingVlanGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.8.1 | Tablehm2AgentSwitchSnoopingVlanTable | not-accessible | current | A table of the IGMP/MLD Snooping Vlan configuration entries. |
| 1.3.6.1.4.1.248.12.1.2.8.8.1.1 | Rowhm2AgentSwitchSnoopingVlanEntry | not-accessible | current | Represents entry for a IGMP/MLD Snooping Vlan. |
| 1.3.6.1.4.1.248.12.1.2.8.8.1.1.1 | Columnhm2AgentSwitchSnoopingVlanAdminMode | read-write | current | This enables or disables IGMP/MLD Snooping on a selected Vlan interface. |
| 1.3.6.1.4.1.248.12.1.2.8.8.1.1.2 | Columnhm2AgentSwitchSnoopingVlanGroupMembershipInterval | read-write | current | The amount of time in seconds that a switch will wait for a report from a particular group on the selected vlan before deleting the interface participating in … |
| 1.3.6.1.4.1.248.12.1.2.8.8.1.1.3 | Columnhm2AgentSwitchSnoopingVlanMaxResponseTime | read-write | current | The amount of time in seconds a switch will wait after sending a query on the selected vlan because it did not receive a report for a particular group in the i… |
| 1.3.6.1.4.1.248.12.1.2.8.8.1.1.4 | Columnhm2AgentSwitchSnoopingVlanFastLeaveAdminMode | read-write | current | This enables or disables IGMP/MLD Snooping on the selected vlan. |
| 1.3.6.1.4.1.248.12.1.2.8.8.1.1.5 | Columnhm2AgentSwitchSnoopingVlanMRPExpirationTime | read-write | current | The amount of time in seconds that a switch will wait for a query to be received on the selected interface participating in the vlan before the interface is re… |
| 1.3.6.1.4.1.248.12.1.2.8.8.1.1.6 | Columnhm2AgentSwitchSnoopingVlanReportSuppMode | read-write | current | This enables or disables IGMP/MLD Snooping Report Suppression feature on the selected vlan. |
| 1.3.6.1.4.1.248.12.1.2.8.9 | Nodehm2AgentSwitchVlanStaticMrouterGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.9.1 | Tablehm2AgentSwitchVlanStaticMrouterTable | not-accessible | current | A table of the IGMP/MLD Static Mrouter Configuration parameters. |
| 1.3.6.1.4.1.248.12.1.2.8.9.1.1 | Rowhm2AgentSwitchVlanStaticMrouterEntry | not-accessible | current | Represents entry for a IGMP/MLD Static Mrouter. |
| 1.3.6.1.4.1.248.12.1.2.8.9.1.1.1 | Columnhm2AgentSwitchVlanStaticMrouterAdminMode | read-write | current | This enables or disables IGMP/MLD mrouter on a per interface per VLAN basis. |
| 1.3.6.1.4.1.248.12.1.2.8.10 | Nodehm2AgentSwitchMFDBGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.10.1 | Tablehm2AgentSwitchMFDBTable | not-accessible | current | The Multicast Forwarding Database table |
| 1.3.6.1.4.1.248.12.1.2.8.10.1.1 | Rowhm2AgentSwitchMFDBEntry | not-accessible | current | Contains Forwarding and Filtering information per Vlan Index, MAC Address, and Component User. |
| 1.3.6.1.4.1.248.12.1.2.8.10.1.1.1 | Columnhm2AgentSwitchMFDBVlanId | read-only | current | Vlan Index for which this entry is associated with. |
| 1.3.6.1.4.1.248.12.1.2.8.10.1.1.2 | Columnhm2AgentSwitchMFDBMacAddress | read-only | current | A multicast MAC address for which the switch has forwarding and or filtering information. |
| 1.3.6.1.4.1.248.12.1.2.8.10.1.1.3 | Columnhm2AgentSwitchMFDBProtocolType | read-only | current | The component that is responsible for this entry in the Multicast Forwarding Database. |
| 1.3.6.1.4.1.248.12.1.2.8.10.1.1.4 | Columnhm2AgentSwitchMFDBType | read-only | current | This displays the type of the entry. static(1) - Entries configured by the end user dynamic(2) - Entries added as a result of a learning process or protocol |
| 1.3.6.1.4.1.248.12.1.2.8.10.1.1.5 | Columnhm2AgentSwitchMFDBDescription | read-only | current | Text description of this multicast table entry. |
| 1.3.6.1.4.1.248.12.1.2.8.10.1.1.6 | Columnhm2AgentSwitchMFDBForwardingPortMask | read-only | current | BitMask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects hm2AgentPortDot1dBasePo… |
| 1.3.6.1.4.1.248.12.1.2.8.10.1.1.7 | Columnhm2AgentSwitchMFDBFilteringPortMask | read-only | current | BitMask indicating which ports this entry indicates should be filtered. To obtain port numbers from interface numbers, use the objects hm2AgentPortDot1dBasePor… |
| 1.3.6.1.4.1.248.12.1.2.8.10.2 | Tablehm2AgentSwitchMFDBSummaryTable | not-accessible | current | The multicast forwarding database summary table. |
| 1.3.6.1.4.1.248.12.1.2.8.10.2.1 | Rowhm2AgentSwitchMFDBSummaryEntry | not-accessible | current | Summarizes the forwarding ports for all components registered for all MFDB table entries with the same Vlan Index and MAC Address. |
| 1.3.6.1.4.1.248.12.1.2.8.10.2.1.1 | Columnhm2AgentSwitchMFDBSummaryVlanId | read-only | current | Vlan Index for which this entry is associated with. |
| 1.3.6.1.4.1.248.12.1.2.8.10.2.1.2 | Columnhm2AgentSwitchMFDBSummaryMacAddress | read-only | current | A multicast MAC address for which the switch has forwarding and or filtering information. |
| 1.3.6.1.4.1.248.12.1.2.8.10.2.1.3 | Columnhm2AgentSwitchMFDBSummaryForwardingPortMask | read-only | current | Port Mask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects hm2AgentPortDot1dBase… |
| 1.3.6.1.4.1.248.12.1.2.8.10.3 | Scalarhm2AgentSwitchMFDBMaxTableEntries | read-only | current | This displays the maximum number of entries that can possibly be in the Multicast Forwarding Database table. |
| 1.3.6.1.4.1.248.12.1.2.8.10.4 | Scalarhm2AgentSwitchMFDBMostEntriesUsed | read-only | current | This displays the largest number of entries that have been present in the Multicast Forwarding Database table. This value is also known as the MFDB high water … |
| 1.3.6.1.4.1.248.12.1.2.8.10.5 | Scalarhm2AgentSwitchMFDBCurrentEntries | read-only | current | This displays the current number of entries in the Multicast Forwarding Database table. |
| 1.3.6.1.4.1.248.12.1.2.8.11 | Nodehm2AgentSwitchDVlanTagGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.11.1 | Scalarhm2AgentSwitchDVlanTagEthertype | read-only | current | Configures the Double Vlan Tag Ethertype for the switch. If this object is supported, ethertype cannot be configured per port. Commonly used are the Ethertypes… |
| 1.3.6.1.4.1.248.12.1.2.8.17 | Nodehm2AgentSwitchVlanMacAssociationGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.17.1 | Tablehm2AgentSwitchVlanMacAssociationTable | not-accessible | current | The switch's MAC To VLAN association table |
| 1.3.6.1.4.1.248.12.1.2.8.17.1.1 | Rowhm2AgentSwitchVlanMacAssociationEntry | not-accessible | current | VLAN to be assigned to untagged or priority tagged packets based on MAC address. |
| 1.3.6.1.4.1.248.12.1.2.8.17.1.1.1 | Columnhm2AgentSwitchVlanMacAssociationMacAddress | not-accessible | current | The Mac address |
| 1.3.6.1.4.1.248.12.1.2.8.17.1.1.2 | Columnhm2AgentSwitchVlanMacAssociationVlanId | not-accessible | current | The VLAN the Mac address assigned to |
| 1.3.6.1.4.1.248.12.1.2.8.17.1.1.3 | Columnhm2AgentSwitchVlanMacAssociationRowStatus | read-create | current | The Mac to VLAN association row status. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry |
| 1.3.6.1.4.1.248.12.1.2.8.18 | Nodehm2AgentSwitchProtectedPortConfigGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.18.1 | Tablehm2AgentSwitchProtectedPortTable | not-accessible | current | The switch's protected port mapping table |
| 1.3.6.1.4.1.248.12.1.2.8.18.1.1 | Rowhm2AgentSwitchProtectedPortEntry | not-accessible | current | Protected ports assigned to groups. |
| 1.3.6.1.4.1.248.12.1.2.8.18.1.1.1 | Columnhm2AgentSwitchProtectedPortGroupId | not-accessible | current | The group that this port belongs to |
| 1.3.6.1.4.1.248.12.1.2.8.18.1.1.2 | Columnhm2AgentSwitchProtectedPortGroupName | read-write | current | The name of the group |
| 1.3.6.1.4.1.248.12.1.2.8.18.1.1.3 | Columnhm2AgentSwitchProtectedPortPortList | read-write | current | The set of ports that are protected in this group |
| 1.3.6.1.4.1.248.12.1.2.8.19 | Nodehm2AgentSwitchVlanSubnetAssociationGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.19.1 | Tablehm2AgentSwitchVlanSubnetAssociationTable | not-accessible | current | The switch's Subnet To VLAN association table |
| 1.3.6.1.4.1.248.12.1.2.8.19.1.1 | Rowhm2AgentSwitchVlanSubnetAssociationEntry | not-accessible | current | VLAN to be assigned to untagged or priority tagged packets based on IP address and Subnet Mask. |
| 1.3.6.1.4.1.248.12.1.2.8.19.1.1.1 | Columnhm2AgentSwitchVlanSubnetAssociationIPAddress | not-accessible | current | The ip address |
| 1.3.6.1.4.1.248.12.1.2.8.19.1.1.2 | Columnhm2AgentSwitchVlanSubnetAssociationSubnetMask | not-accessible | current | The subnet mask |
| 1.3.6.1.4.1.248.12.1.2.8.19.1.1.3 | Columnhm2AgentSwitchVlanSubnetAssociationVlanId | not-accessible | current | The VLAN that the IP address and subnet mask assigned to |
| 1.3.6.1.4.1.248.12.1.2.8.19.1.1.4 | Columnhm2AgentSwitchVlanSubnetAssociationRowStatus | read-create | current | The Subnet to VLAN association row status. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry |
| 1.3.6.1.4.1.248.12.1.2.8.20 | Nodehm2AgentSwitchSnoopingQuerierGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.20.1 | Tablehm2AgentSwitchSnoopingQuerierCfgTable | not-accessible | current | A table of the IGMP/MLD Snooping Querier Global configuration entries. |
| 1.3.6.1.4.1.248.12.1.2.8.20.1.1 | Rowhm2AgentSwitchSnoopingQuerierCfgEntry | not-accessible | current | Represents entry for Snooping Querier Configuration. |
| 1.3.6.1.4.1.248.12.1.2.8.20.1.1.1 | Columnhm2AgentSwitchSnoopingQuerierAdminMode | read-write | current | This enables or disables Snooping Querier on the system. |
| 1.3.6.1.4.1.248.12.1.2.8.20.1.1.2 | Columnhm2AgentSwitchSnoopingQuerierVersion | read-write | current | This specifies the multicast protocol versions that are supported by the system. |
| 1.3.6.1.4.1.248.12.1.2.8.20.1.1.4 | Columnhm2AgentSwitchSnoopingQuerierQueryInterval | read-write | current | This specified the timer interval after which the system generates general queries. |
| 1.3.6.1.4.1.248.12.1.2.8.20.1.1.5 | Columnhm2AgentSwitchSnoopingQuerierExpiryInterval | read-write | current | This specified the timer interval after which the detected other querier information is no longer valid. |
| 1.3.6.1.4.1.248.12.1.2.8.20.2 | Tablehm2AgentSwitchSnoopingQuerierVlanTable | not-accessible | current | A table of the Snooping Querier Vlan configuration entries. |
| 1.3.6.1.4.1.248.12.1.2.8.20.2.1 | Rowhm2AgentSwitchSnoopingQuerierVlanEntry | not-accessible | current | Represents entry for a Snooping Querier configurable Vlan. |
| 1.3.6.1.4.1.248.12.1.2.8.20.2.1.1 | Columnhm2AgentSwitchSnoopingQuerierVlanAdminMode | read-write | current | This enables or disables Snooping Querier on a selected Vlan interface. |
| 1.3.6.1.4.1.248.12.1.2.8.20.2.1.2 | Columnhm2AgentSwitchSnoopingQuerierVlanOperMode | read-only | current | This specifies the current state of the Snooping Querier on a selected vlan interface |
| 1.3.6.1.4.1.248.12.1.2.8.20.2.1.3 | Columnhm2AgentSwitchSnoopingQuerierElectionParticipateMode | read-write | deprecated | This object is deprecated. This enables or disables the Snooping Querier Election Participation mode. When enabled snooping querier switch will participate in … |
| 1.3.6.1.4.1.248.12.1.2.8.20.2.1.4 | Columnhm2AgentSwitchSnoopingQuerierVlanAddress | read-write | current | This specifies the default source ip address to be used while generating general queries on the specified vlan. |
| 1.3.6.1.4.1.248.12.1.2.8.20.2.1.5 | Columnhm2AgentSwitchSnoopingQuerierOperVersion | read-only | current | This specifies the multicast protocol version that is currently being used by the snooping switch for the specified vlan while generating query messages. |
| 1.3.6.1.4.1.248.12.1.2.8.20.2.1.6 | Columnhm2AgentSwitchSnoopingQuerierOperMaxResponseTime | read-only | current | The amount of time in seconds a switch will wait after sending a query on the selected vlan because it did not receive a report for a particular group in the i… |
| 1.3.6.1.4.1.248.12.1.2.8.20.2.1.7 | Columnhm2AgentSwitchSnoopingQuerierLastQuerierAddress | read-only | current | This specifies the last querier's ip address for the specified vlan. It represents the detected other multicast querier in the vlan. |
| 1.3.6.1.4.1.248.12.1.2.8.20.2.1.8 | Columnhm2AgentSwitchSnoopingQuerierLastQuerierVersion | read-only | current | This specifies the multicast protocol version that is currently being used by the detected other multicast querier for the specified vlan. (-1) - indicates tha… |
| 1.3.6.1.4.1.248.12.1.2.8.21 | Nodehm2AgentDaiConfigGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.21.1 | Scalarhm2AgentDaiSrcMacValidate | read-write | current | This object indicates whether Sender MAC validation in the ARP packets is enabled. If this object is set to 'true', validation is enabled. If this object is se… |
| 1.3.6.1.4.1.248.12.1.2.8.21.2 | Scalarhm2AgentDaiDstMacValidate | read-write | current | This object indicates whether Target MAC validation in the ARP Response packets is enabled. If this object is set to 'true', validation is enabled. If this obj… |
| 1.3.6.1.4.1.248.12.1.2.8.21.3 | Scalarhm2AgentDaiIPValidate | read-write | current | This object indicates whether IP address validation in the ARP packets is enabled. If this object is set to 'true', validation is enabled. If this object is se… |
| 1.3.6.1.4.1.248.12.1.2.8.21.4 | Tablehm2AgentDaiVlanConfigTable | not-accessible | current | A table provides the mechanism to control Dynamic ARP Inspection per VLAN. When a VLAN is created in a device supporting this table, a corresponding entry of t… |
| 1.3.6.1.4.1.248.12.1.2.8.21.4.1 | Rowhm2AgentDaiVlanConfigEntry | not-accessible | current | A row instance contains the configuration for Dynamic ARP Inspection at each existing VLAN. |
| 1.3.6.1.4.1.248.12.1.2.8.21.4.1.1 | Columnhm2AgentDaiVlanIndex | not-accessible | current | This object indicates the VLAN number on which Dynamic ARP Inspection feature is configured. |
| 1.3.6.1.4.1.248.12.1.2.8.21.4.1.2 | Columnhm2AgentDaiVlanDynArpInspEnable | read-write | current | This object indicates whether Dynamic ARP Inspection is enabled in this VLAN. If this object is set to 'true', Dynamic ARP Inspection is enabled. If this objec… |
| 1.3.6.1.4.1.248.12.1.2.8.21.4.1.3 | Columnhm2AgentDaiVlanLoggingEnable | read-write | current | This object indicates whether the Dynamic ARP Inspection logging is enabled on this VlAN. If this object is set to 'true', Dynamic ARP Inspection logging is en… |
| 1.3.6.1.4.1.248.12.1.2.8.21.4.1.4 | Columnhm2AgentDaiVlanArpAclName | read-write | current | This object indicates the ARP ACL name set for this VLAN. Notice that the ACL is regarded only if the corresponding row in 'agentArpAclTable' is active. |
| 1.3.6.1.4.1.248.12.1.2.8.21.4.1.5 | Columnhm2AgentDaiVlanArpAclStaticFlag | read-write | current | If an ARP ACL is defined for the VLAN and there is no match for the received ARP packet, the further proceeding depends on this MIB object. If it is 'true', th… |
| 1.3.6.1.4.1.248.12.1.2.8.21.4.1.248 | Columnhm2AgentDaiVlanBindingCheckEnable | read-write | current | If enabled, the ARP frame received on an untrusted port (in a DAI enabled VLAN) is checked against the ARP ACL and the DHCP Snooping bindings database. If disa… |
| 1.3.6.1.4.1.248.12.1.2.8.21.5 | Scalarhm2AgentDaiStatsReset | read-write | current | Clear the DAI statistics on all vlans. A value of reset(1) is used to reset the statistics. A read on this object will always return the value none(0). The val… |
| 1.3.6.1.4.1.248.12.1.2.8.21.6 | Tablehm2AgentDaiVlanStatsTable | not-accessible | current | A table provides the mechanism to control Dynamic ARP Inspection per VLAN. When a VLAN is created in a device supporting this table, a corresponding entry of t… |
| 1.3.6.1.4.1.248.12.1.2.8.21.6.1 | Rowhm2AgentDaiVlanStatsEntry | not-accessible | current | A row instance contains the Dynamic ARP Inspection statistics per VLAN. |
| 1.3.6.1.4.1.248.12.1.2.8.21.6.1.1 | Columnhm2AgentDaiVlanStatsIndex | not-accessible | current | This object indicates the VLAN number on which Dynamic ARP Inspection statistics are retrieved. |
| 1.3.6.1.4.1.248.12.1.2.8.21.6.1.2 | Columnhm2AgentDaiVlanPktsForwarded | read-only | current | Number of valid ARP packets forwarded by DAI. |
| 1.3.6.1.4.1.248.12.1.2.8.21.6.1.3 | Columnhm2AgentDaiVlanPktsDropped | read-only | current | Number of invalid ARP packets dropped by DAI. |
| 1.3.6.1.4.1.248.12.1.2.8.21.6.1.4 | Columnhm2AgentDaiVlanDhcpDrops | read-only | current | Number of ARP packets that were dropped by DAI as there is no matching DHCP Snooping binding entry found. |
| 1.3.6.1.4.1.248.12.1.2.8.21.6.1.5 | Columnhm2AgentDaiVlanDhcpPermits | read-only | current | Number of ARP packets that were forwarded by DAI as there is a matching DHCP Snooping binding entry found. |
| 1.3.6.1.4.1.248.12.1.2.8.21.6.1.6 | Columnhm2AgentDaiVlanAclDrops | read-only | current | Number of ARP packets that were dropped by DAI as there is no matching ARP ACL rule found for this Vlan and the static flag is set on this vlan. |
| 1.3.6.1.4.1.248.12.1.2.8.21.6.1.7 | Columnhm2AgentDaiVlanAclPermits | read-only | current | Number of ARP packets that were permitted by DAI as there is a matching ARP ACL rule found for this Vlan. |
| 1.3.6.1.4.1.248.12.1.2.8.21.6.1.8 | Columnhm2AgentDaiVlanSrcMacFailures | read-only | current | Number of ARP packets that were dropped by DAI as the sender mac address in ARP packet didn't match the source mac in ethernet header. |
| 1.3.6.1.4.1.248.12.1.2.8.21.6.1.9 | Columnhm2AgentDaiVlanDstMacFailures | read-only | current | Number of ARP packets that were dropped by DAI as the target mac address in ARP reply packet didn't match the destination mac in ethernet header. |
| 1.3.6.1.4.1.248.12.1.2.8.21.6.1.10 | Columnhm2AgentDaiVlanIpValidFailures | read-only | current | Number of ARP packets that were dropped by DAI as the sender IP address in ARP packet or target IP address in ARP reply packet is invalid. Invalid addresses in… |
| 1.3.6.1.4.1.248.12.1.2.8.21.7 | Tablehm2AgentDaiIfConfigTable | not-accessible | current | A table provides the mechanism to configure the trust state for Dynamic ARP Inspection purpose at each physical interface capable of this feature. |
| 1.3.6.1.4.1.248.12.1.2.8.21.7.1 | Rowhm2AgentDaiIfConfigEntry | not-accessible | current | A row instance contains the configuration for Dynamic ARP Inspection at each physical interface capable of this feature. |
| 1.3.6.1.4.1.248.12.1.2.8.21.7.1.1 | Columnhm2AgentDaiIfTrustEnable | read-write | current | This object indicates whether the interface is trusted for Dynamic ARP Inspection purpose. If this object is set to 'true', the interface is trusted. ARP packe… |
| 1.3.6.1.4.1.248.12.1.2.8.21.7.1.2 | Columnhm2AgentDaiIfRateLimit | read-write | current | This object indicates rate limit value for Dynamic ARP Inspection purpose. If the incoming rate of ARP packets exceeds the value of this object for consecutive… |
| 1.3.6.1.4.1.248.12.1.2.8.21.7.1.3 | Columnhm2AgentDaiIfBurstInterval | read-write | current | This object indicates the burst interval value for rate limiting purpose on this interface. |
| 1.3.6.1.4.1.248.12.1.2.8.21.7.1.248 | Columnhm2AgentDaiIfAutoDisable | read-write | current | This object indicates whether a port is auto-disabled when the configured ARP threshold is exceeded. |
| 1.3.6.1.4.1.248.12.1.2.8.22 | Nodehm2AgentArpAclGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.22.1 | Tablehm2AgentArpAclTable | not-accessible | current | A table of the ARP ACL entries |
| 1.3.6.1.4.1.248.12.1.2.8.22.1.1 | Rowhm2AgentArpAclEntry | not-accessible | current | Represents entry for an ARP ACL |
| 1.3.6.1.4.1.248.12.1.2.8.22.1.1.1 | Columnhm2AgentArpAclName | read-create | current | Name of the ARP ACL, which must consist of 1 to 31 alphanumeric characters and uniquely identify this ARP ACL. This object must be set to complete a new ARP AC… |
| 1.3.6.1.4.1.248.12.1.2.8.22.1.1.2 | Columnhm2AgentArpAclRowStatus | read-create | current | The status of this conceptual row. Entries can not be deleted until all rows in arpAclRuleTable with corresponding values of arpAclIndex have been deleted. act… |
| 1.3.6.1.4.1.248.12.1.2.8.22.2 | Tablehm2AgentArpAclRuleTable | not-accessible | current | A table of the ARP ACL Rule entries |
| 1.3.6.1.4.1.248.12.1.2.8.22.2.1 | Rowhm2AgentArpAclRuleEntry | not-accessible | current | Represents entry for a set of ARP ACL-match rules |
| 1.3.6.1.4.1.248.12.1.2.8.22.2.1.1 | Columnhm2AgentArpAclRuleMatchSenderIpAddr | read-create | current | Sender IP address match value for the ARP ACL. This address must be a unicast address unequal to 0.0.0.0. |
| 1.3.6.1.4.1.248.12.1.2.8.22.2.1.2 | Columnhm2AgentArpAclRuleMatchSenderMacAddr | read-create | current | Sender MAC address match value for the ARP ACL. This address must be a unicast address unequal to 00:0:00:00:00:00. |
| 1.3.6.1.4.1.248.12.1.2.8.22.2.1.3 | Columnhm2AgentArpAclRuleRowStatus | read-create | current | The status of this conceptual row. active(1) - This ACL Rule is active. notInService(2) - Row has been suspended. notReady(3) - Row has incomplete values. crea… |
| 1.3.6.1.4.1.248.12.1.2.8.23 | Nodehm2AgentDhcpSnoopingConfigGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.23.1 | Scalarhm2AgentDhcpSnoopingAdminMode | read-write | current | This object indicates whether DHCP Snooping is enabled globally. If this object is set to 'true',admin mode is enabled globally. If this object is set to 'fals… |
| 1.3.6.1.4.1.248.12.1.2.8.23.2 | Scalarhm2AgentDhcpSnoopingVerifyMac | read-write | current | This object indicates whether source Mac address in the received DHCP Message needs to be verified or not. If this object is set to 'true',verifyMac is enabled… |
| 1.3.6.1.4.1.248.12.1.2.8.23.3 | Tablehm2AgentDhcpSnoopingVlanConfigTable | not-accessible | current | A table provides the mechanism to control DHCP SNOOPING per VLAN. When a VLAN is created in a device supporting this table, a corresponding entry of this table… |
| 1.3.6.1.4.1.248.12.1.2.8.23.3.1 | Rowhm2AgentDhcpSnoopingVlanConfigEntry | not-accessible | current | A row instance contains the configuration for DHCP SNOOPING at each existing VLAN. |
| 1.3.6.1.4.1.248.12.1.2.8.23.3.1.1 | Columnhm2AgentDhcpSnoopingVlanIndex | not-accessible | current | This object indicates the VLAN number on which DHCP SNOOPING Inspection feature is configured. |
| 1.3.6.1.4.1.248.12.1.2.8.23.3.1.2 | Columnhm2AgentDhcpSnoopingVlanEnable | read-write | current | This object indicates whether DHCP SNOOPING is enabled in this VLAN. If this object is set to 'true', DHCP SNOOPING is enabled. If this object is set to 'false… |
| 1.3.6.1.4.1.248.12.1.2.8.23.4 | Tablehm2AgentDhcpSnoopingIfConfigTable | not-accessible | current | A table provides the mechanism to configure the trust state for DHCP snooping purpose at each physical interface capable of this feature. |
| 1.3.6.1.4.1.248.12.1.2.8.23.4.1 | Rowhm2AgentDhcpSnoopingIfConfigEntry | not-accessible | current | A row instance contains the configuration for DHCP snooping at each physical interface capable of this feature. |
| 1.3.6.1.4.1.248.12.1.2.8.23.4.1.1 | Columnhm2AgentDhcpSnoopingIfTrustEnable | read-write | current | This object indicates whether the interface is trusted for DHCP snooping purpose. |
| 1.3.6.1.4.1.248.12.1.2.8.23.4.1.2 | Columnhm2AgentDhcpSnoopingIfLogEnable | read-write | current | This object indicates whether the Logging needs on DHCP snooping validations or not |
| 1.3.6.1.4.1.248.12.1.2.8.23.4.1.3 | Columnhm2AgentDhcpSnoopingIfRateLimit | read-write | current | This object indicates rate limit value for DHCP Snooping purpose. If the incoming rate of DHCP packets exceeds the value of this object for consecutively burst… |
| 1.3.6.1.4.1.248.12.1.2.8.23.4.1.4 | Columnhm2AgentDhcpSnoopingIfBurstInterval | read-write | current | This object indicates the burst interval value for rate limiting purpose on this interface. |
| 1.3.6.1.4.1.248.12.1.2.8.23.4.1.248 | Columnhm2AgentDhcpSnoopingIfAutoDisable | read-write | current | This object indicates whether a port is auto-disabled when the configured threshold is reached. |
| 1.3.6.1.4.1.248.12.1.2.8.23.5 | Tablehm2AgentIpsgIfConfigTable | not-accessible | current | A table provides the mechanism to configure the IPSG at each physical interface capable of this feature. |
| 1.3.6.1.4.1.248.12.1.2.8.23.5.1 | Rowhm2AgentIpsgIfConfigEntry | not-accessible | current | A row instance contains the configuration for IPSG at each physical interface capable of this feature. |
| 1.3.6.1.4.1.248.12.1.2.8.23.5.1.1 | Columnhm2AgentIpsgIfVerifySource | read-write | current | This object indicates whether IP packets received on this interface are filtered based on whether IP Source Guard considers the source IP address to be a valid… |
| 1.3.6.1.4.1.248.12.1.2.8.23.5.1.2 | Columnhm2AgentIpsgIfPortSecurity | read-write | current | This object indicates whether IP packets received on this interface are filtered based on whether IP Source Guard considers the source MAC address to be a vali… |
| 1.3.6.1.4.1.248.12.1.2.8.23.6 | Scalarhm2AgentDhcpSnoopingStatsReset | read-write | current | Clear the DHCP snooping statistics on all ports. A value of reset(1) is used to reset the statistics. A read on this object will always return the value none(0… |
| 1.3.6.1.4.1.248.12.1.2.8.23.7 | Tablehm2AgentDhcpSnoopingStatsTable | not-accessible | current | A table provides the mechanism for statics of DHCP snooping. |
| 1.3.6.1.4.1.248.12.1.2.8.23.7.1 | Rowhm2AgentDhcpSnoopingStatsEntry | not-accessible | current | A row instance contains the DHCP snooping statistics per VLAN. |
| 1.3.6.1.4.1.248.12.1.2.8.23.7.1.1 | Columnhm2AgentDhcpSnoopingMacVerifyFailures | read-only | current | This object indicates the number of failure verifications of client mac address with source mac address |
| 1.3.6.1.4.1.248.12.1.2.8.23.7.1.2 | Columnhm2AgentDhcpSnoopingInvalidClientMessages | read-only | current | This object indicates the number of invalid DHCP releases and deny messages |
| 1.3.6.1.4.1.248.12.1.2.8.23.7.1.3 | Columnhm2AgentDhcpSnoopingInvalidServerMessages | read-only | current | This object indicates the number of invalid DHCP server mesaages |
| 1.3.6.1.4.1.248.12.1.2.8.23.8 | Tablehm2AgentStaticIpsgBindingTable | not-accessible | current | A table of the IPSG static entries |
| 1.3.6.1.4.1.248.12.1.2.8.23.8.1 | Rowhm2AgentStaticIpsgBindingEntry | not-accessible | current | Represents a binding in IPSG table |
| 1.3.6.1.4.1.248.12.1.2.8.23.8.1.1 | Columnhm2AgentStaticIpsgBindingIfIndex | read-create | current | Interface on which this IPSG binding is going to be added. |
| 1.3.6.1.4.1.248.12.1.2.8.23.8.1.2 | Columnhm2AgentStaticIpsgBindingVlanId | read-create | current | VLAN to which this IPSG binding is going to be added. |
| 1.3.6.1.4.1.248.12.1.2.8.23.8.1.3 | Columnhm2AgentStaticIpsgBindingMacAddr | read-create | current | MAC address match value for the IPSG Binding. This address must be a unicast address unequal to 00:0:00:00:00:00. |
| 1.3.6.1.4.1.248.12.1.2.8.23.8.1.4 | Columnhm2AgentStaticIpsgBindingIpAddr | read-create | current | IP address match value for the IPSG Binding. This address must be a unicast address unequal to 0.0.0.0. |
| 1.3.6.1.4.1.248.12.1.2.8.23.8.1.5 | Columnhm2AgentStaticIpsgBindingRowStatus | read-create | current | The status of this conceptual row. active(1) - This DHCP Snooping binding is active. notInService(2) - Row has been suspended. notReady(3) - Row has incomplete… |
| 1.3.6.1.4.1.248.12.1.2.8.23.8.1.248 | Columnhm2AgentStaticIpsgBindingHwStatus | read-only | current | Set to true when Binding is applied to the Hardware |
| 1.3.6.1.4.1.248.12.1.2.8.23.9 | Tablehm2AgentDynamicIpsgBindingTable | not-accessible | current | A table of the IPSG dynamic entries |
| 1.3.6.1.4.1.248.12.1.2.8.23.9.1 | Rowhm2AgentDynamicIpsgBindingEntry | not-accessible | current | Represents a binding in IPSG table |
| 1.3.6.1.4.1.248.12.1.2.8.23.9.1.1 | Columnhm2AgentDynamicIpsgBindingIfIndex | read-only | current | Interface on which this IPSG binding is added. |
| 1.3.6.1.4.1.248.12.1.2.8.23.9.1.2 | Columnhm2AgentDynamicIpsgBindingVlanId | read-only | current | VLAN to which this IPSG binding is going to be added. |
| 1.3.6.1.4.1.248.12.1.2.8.23.9.1.3 | Columnhm2AgentDynamicIpsgBindingMacAddr | read-only | current | MAC address match value for the IPSG Binding. |
| 1.3.6.1.4.1.248.12.1.2.8.23.9.1.4 | Columnhm2AgentDynamicIpsgBindingIpAddr | read-only | current | Sender IP address match value for the IPSG Binding. |
| 1.3.6.1.4.1.248.12.1.2.8.23.9.1.248 | Columnhm2AgentDynamicIpsgBindingHwStatus | read-only | current | Set to true when Binding is applied to the Hardware |
| 1.3.6.1.4.1.248.12.1.2.8.23.10 | Tablehm2AgentStaticDsBindingTable | not-accessible | current | A table of the DHCP SNOOPING static entries |
| 1.3.6.1.4.1.248.12.1.2.8.23.10.1 | Rowhm2AgentStaticDsBindingEntry | not-accessible | current | Represents a binding in DHCP SNOOPING table |
| 1.3.6.1.4.1.248.12.1.2.8.23.10.1.1 | Columnhm2AgentStaticDsBindingIfIndex | read-create | current | Interface on which this DHCP SNOOPING binding is going to be added. |
| 1.3.6.1.4.1.248.12.1.2.8.23.10.1.2 | Columnhm2AgentStaticDsBindingVlanId | read-create | current | VLAN to which this DHCP SNOOPING binding is going to be added. |
| 1.3.6.1.4.1.248.12.1.2.8.23.10.1.3 | Columnhm2AgentStaticDsBindingMacAddr | read-create | current | MAC address match value for the DHCP SNOOPING Binding. This address must be a unicast address unequal to 00:0:00:00:00:00. |
| 1.3.6.1.4.1.248.12.1.2.8.23.10.1.4 | Columnhm2AgentStaticDsBindingIpAddr | read-create | current | IP address match value for the DHCP SNOOPING Binding. This address must be a unicast address unequal to 0.0.0.0. |
| 1.3.6.1.4.1.248.12.1.2.8.23.10.1.5 | Columnhm2AgentStaticDsBindingRowStatus | read-create | current | The status of this conceptual row. active(1) - This DHCP Snooping binding is active. notInService(2) - Row has been suspended. notReady(3) - Row has incomplete… |
| 1.3.6.1.4.1.248.12.1.2.8.23.11 | Tablehm2AgentDynamicDsBindingTable | not-accessible | current | A table of the DHCP SNOOPING Dynamic entries |
| 1.3.6.1.4.1.248.12.1.2.8.23.11.1 | Rowhm2AgentDynamicDsBindingEntry | not-accessible | current | Represents a binding in DHCP SNOOPING table |
| 1.3.6.1.4.1.248.12.1.2.8.23.11.1.1 | Columnhm2AgentDynamicDsBindingIfIndex | read-only | current | Interface on which this DHCP SNOOPING binding is going to be added. |
| 1.3.6.1.4.1.248.12.1.2.8.23.11.1.2 | Columnhm2AgentDynamicDsBindingVlanId | read-only | current | VLAN to which this DHCP SNOOPING binding is going to be added. |
| 1.3.6.1.4.1.248.12.1.2.8.23.11.1.3 | Columnhm2AgentDynamicDsBindingMacAddr | read-only | current | MAC address match value for the DHCP SNOOPING Binding. |
| 1.3.6.1.4.1.248.12.1.2.8.23.11.1.4 | Columnhm2AgentDynamicDsBindingIpAddr | read-only | current | IP address match value for the DHCP SNOOPING Binding. |
| 1.3.6.1.4.1.248.12.1.2.8.23.11.1.5 | Columnhm2AgentDynamicDsBindingLeaseRemainingTime | read-only | current | This specifies the period for which the DHCP SNOOPING Binding is valid. |
| 1.3.6.1.4.1.248.12.1.2.8.23.12 | Scalarhm2AgentDhcpSnoopingRemoteFileName | read-write | current | This object indicates the file name on the remote machine to save the DHCP Snooping bindings. |
| 1.3.6.1.4.1.248.12.1.2.8.23.13 | Scalarhm2AgentDhcpSnoopingRemoteIpAddr | read-write | current | This object indicates the IP address of the remote machine to save the DHCP Snooping bindings. This will be set only when we have a valid file name. |
| 1.3.6.1.4.1.248.12.1.2.8.23.14 | Scalarhm2AgentDhcpSnoopingStoreInterval | read-write | current | This object indicates the perodic time interval to save the (changed) DHCP Snooping bindings database. |
| 1.3.6.1.4.1.248.12.1.2.8.24 | Nodehm2AgentDhcpL2RelayConfigGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.24.1 | Scalarhm2AgentDhcpL2RelayAdminMode | read-write | current | This object indicates whether DHCP L2 Relay is enabled globally. If this object is set to 'true',admin mode is enabled globally. If this object is set to 'fals… |
| 1.3.6.1.4.1.248.12.1.2.8.24.2 | Tablehm2AgentDhcpL2RelayIfConfigTable | not-accessible | current | A table provides the mechanism to enable/disable and configure the trust state for DHCP L2Relay purpose at each physical interface capable of this feature. |
| 1.3.6.1.4.1.248.12.1.2.8.24.2.1 | Rowhm2AgentDhcpL2RelayIfConfigEntry | not-accessible | current | A row instance contains the configuration for DHCP L2 Relay at each physical interface capable of this feature. |
| 1.3.6.1.4.1.248.12.1.2.8.24.2.1.1 | Columnhm2AgentDhcpL2RelayIfEnable | read-write | current | This object indicates whether the DHCP L2Relay is enabled or not |
| 1.3.6.1.4.1.248.12.1.2.8.24.2.1.2 | Columnhm2AgentDhcpL2RelayIfTrustEnable | read-write | current | This object indicates whether the interface is trusted for DHCP L2 Relay purpose. |
| 1.3.6.1.4.1.248.12.1.2.8.24.3 | Tablehm2AgentDhcpL2RelayVlanConfigTable | not-accessible | current | A table provides the mechanism to control DHCP L2 Relay per VLAN. When a VLAN is created in a device supporting this table, a corresponding entry of this table… |
| 1.3.6.1.4.1.248.12.1.2.8.24.3.1 | Rowhm2AgentDhcpL2RelayVlanConfigEntry | not-accessible | current | A row instance contains the configuration for DHCP L2 Relay at each existing VLAN. |
| 1.3.6.1.4.1.248.12.1.2.8.24.3.1.1 | Columnhm2AgentDhcpL2RelayVlanIndex | not-accessible | current | This object indicates the VLAN number on which DHCP L2 Relay feature is configured. |
| 1.3.6.1.4.1.248.12.1.2.8.24.3.1.2 | Columnhm2AgentDhcpL2RelayVlanEnable | read-write | current | This object indicates whether DHCP L2 Relay is enabled in this VLAN. If this object is set to 'true', DHCP L2 Relay is enabled. If this object is set to 'false… |
| 1.3.6.1.4.1.248.12.1.2.8.24.3.1.3 | Columnhm2AgentDhcpL2RelayCircuitIdVlanEnable | read-write | current | This object indicates whether DHCP CircuitId is enabled for L2 relaying in this VLAN. If this object is set to 'true', DHCP CircuitId is enabled. If this objec… |
| 1.3.6.1.4.1.248.12.1.2.8.24.3.1.4 | Columnhm2AgentDhcpL2RelayRemoteIdVlanEnable | read-write | current | When this object is set with a non-empty string, DHCP RemoteId is enabled for L2 relaying in this VLAN. Notice that you can set this object only if hm2AgentDhc… |
| 1.3.6.1.4.1.248.12.1.2.8.24.3.1.248 | Columnhm2AgentDhcpL2RelayVlanRemoteIdType | read-write | current | This option determines the content of the option 82 Remote ID. ip(1) - inserts the IP address mac(2) - inserts the MAC adress client-id(3) - inserts the client… |
| 1.3.6.1.4.1.248.12.1.2.8.24.6 | Scalarhm2AgentDhcpL2RelayStatsReset | read-write | current | Clear the DHCP L2Relay statistics on all ports. A value of reset(1) is used to reset the statistics. A read on this object will always return the value none(0)… |
| 1.3.6.1.4.1.248.12.1.2.8.24.7 | Tablehm2AgentDhcpL2RelayStatsTable | not-accessible | current | A table provides the mechanism for statics of DHCP L2 Relay. |
| 1.3.6.1.4.1.248.12.1.2.8.24.7.1 | Rowhm2AgentDhcpL2RelayStatsEntry | not-accessible | current | A row instance contains the DHCP L2Relay statistics per interface. |
| 1.3.6.1.4.1.248.12.1.2.8.24.7.1.1 | Columnhm2AgentDhcpL2RelayUntrustedSrvrMsgsWithOptn82 | read-only | current | This object indicates the number of DHCP server messages received with Option-82 field on the untrusted interface. |
| 1.3.6.1.4.1.248.12.1.2.8.24.7.1.2 | Columnhm2AgentDhcpL2RelayUntrustedClntMsgsWithOptn82 | read-only | current | This object indicates the number of DHCP client messages received with Option-82 field on the untrusted interface. |
| 1.3.6.1.4.1.248.12.1.2.8.24.7.1.3 | Columnhm2AgentDhcpL2RelayTrustedSrvrMsgsWithoutOptn82 | read-only | current | This object indicates the number of DHCP server messages received without Option-82 field on the trusted interface. |
| 1.3.6.1.4.1.248.12.1.2.8.24.7.1.4 | Columnhm2AgentDhcpL2RelayTrustedClntMsgsWithoutOptn82 | read-only | current | This object indicates the number of DHCP client messages received without Option-82 field on the trusted interface. |
| 1.3.6.1.4.1.248.12.1.2.8.25 | Nodehm2AgentSwitchVoiceVLANGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.25.1 | Scalarhm2AgentSwitchVoiceVLANAdminMode | read-write | current | This enables or disables Voice VLAN on the system. |
| 1.3.6.1.4.1.248.12.1.2.8.25.2 | Tablehm2AgentSwitchVoiceVlanDeviceTable | not-accessible | current | A table of the Voice Vlan device entries. |
| 1.3.6.1.4.1.248.12.1.2.8.25.2.1 | Rowhm2AgentSwitchVoiceVlanDeviceEntry | not-accessible | current | Represents entry for a Voice Device on the interface. |
| 1.3.6.1.4.1.248.12.1.2.8.25.2.1.1 | Columnhm2AgentSwitchVoiceVlanInterfaceNum | read-only | current | The interface number of this interface. |
| 1.3.6.1.4.1.248.12.1.2.8.25.2.1.2 | Columnhm2AgentSwitchVoiceVlanDeviceMacAddress | read-only | current | The Voice Device Mac address |
| 1.3.6.1.4.1.248.12.1.2.8.26 | Nodehm2AgentSwitchAddressConflictGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.26.1 | Scalarhm2AgentSwitchAddressConflictDetectionStatus | read-only | current | Displays if an address conflict was detected on the switch since the last reset of the status. Set to 'true' if detected, 'false' otherwise. |
| 1.3.6.1.4.1.248.12.1.2.8.26.2 | Scalarhm2AgentSwitchAddressConflictDetectionStatusReset | read-write | current | Clear the last address conflict detection status in the switch. A value of reset(1) is used to reset the status. A read on this object always returns the value… |
| 1.3.6.1.4.1.248.12.1.2.8.26.3 | Scalarhm2AgentSwitchLastConflictingIPAddr | read-only | current | The reported conflicting IP address on the switch since the last reset of the conflict detection status. |
| 1.3.6.1.4.1.248.12.1.2.8.26.4 | Scalarhm2AgentSwitchLastConflictingMacAddr | read-only | current | The MAC address of the host corresponding to the reported conflicting IP address on the switch since the last reset of the conflict detection status. |
| 1.3.6.1.4.1.248.12.1.2.8.26.5 | Scalarhm2AgentSwitchLastConflictReportedTime | read-only | current | Time since the last address conflict was detected. It is displayed in days, hours, minutes and seconds. It is set to a valid value only when the conflict detec… |
| 1.3.6.1.4.1.248.12.1.2.8.26.6 | Scalarhm2AgentSwitchConflictIPAddr | accessible-for-notify | current | The IP address on the switch reported to have a conflict with another host's IP address. |
| 1.3.6.1.4.1.248.12.1.2.8.26.7 | Scalarhm2AgentSwitchConflictMacAddr | accessible-for-notify | current | The MAC address of the host that has an IP address conflicting with the IP address on the switch. |
| 1.3.6.1.4.1.248.12.1.2.8.26.8 | Scalarhm2AgentSwitchAddressConflictDetectionRun | read-write | current | Trigger the action to run the active address conflict detection. A value of run(1) is used to issue the action command. A read on this object always returns th… |
| 1.3.6.1.4.1.248.12.1.2.8.26.248 | Scalarhm2AgentSwitchAddressConflictTrap | read-write | current | Enable or disable the sending of conflict traps. |
| 1.3.6.1.4.1.248.12.1.2.8.27 | Nodehm2AgentSdmPreferConfigGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.27.1 | Scalarhm2AgentSdmPreferCurrentTemplate | read-only | current | Displays the current active SDM Template. |
| 1.3.6.1.4.1.248.12.1.2.8.27.2 | Scalarhm2AgentSdmPreferNextTemplate | read-write | current | Configures the next active template. It will be active only after the next reboot. To revert to the default template after the next reboot, use the option defa… |
| 1.3.6.1.4.1.248.12.1.2.8.28 | Nodehm2AgentSdmTemplateSummaryTable | |||
| 1.3.6.1.4.1.248.12.1.2.8.28.1 | Tablehm2AgentSdmTemplateTable | not-accessible | current | Displays Switch Database Management Template Information. |
| 1.3.6.1.4.1.248.12.1.2.8.28.1.1 | Rowhm2AgentSdmTemplateEntry | not-accessible | current | Information about a SDM Template table entry. |
| 1.3.6.1.4.1.248.12.1.2.8.28.1.1.1 | Columnhm2AgentSdmTemplateId | not-accessible | current | The SDM Template type this instance is associated with. |
| 1.3.6.1.4.1.248.12.1.2.8.28.1.1.2 | Columnhm2AgentArpEntries | read-only | current | The maximum number of entries in the IPv4 Address Resolution Protocol (ARP) cache for routing interfaces. |
| 1.3.6.1.4.1.248.12.1.2.8.28.1.1.3 | Columnhm2AgentIPv4UnicastRoutes | read-only | current | The maximum number of IPv4 unicast forwarding table entries. |
| 1.3.6.1.4.1.248.12.1.2.8.28.1.1.4 | Columnhm2AgentIPv6NdpEntries | read-only | current | The maximum number of IPv6 Neighbor Discovery Protocol (NDP) cache entries. |
| 1.3.6.1.4.1.248.12.1.2.8.28.1.1.5 | Columnhm2AgentIPv6UnicastRoutes | read-only | current | The maximum number of IPv6 unicast forwarding table entries. |
| 1.3.6.1.4.1.248.12.1.2.8.28.1.1.6 | Columnhm2AgentEcmpNextHops | read-only | current | The maximum number of Equal cost next hops that can be installed in the IPv4 and IPv6 unicast forwarding tables. |
| 1.3.6.1.4.1.248.12.1.2.8.28.1.1.7 | Columnhm2AgentIPv4MulticastRoutes | read-only | current | The maximum number of IPv4 multicast forwarding table entries. |
| 1.3.6.1.4.1.248.12.1.2.8.28.1.1.8 | Columnhm2AgentIPv6MulticastRoutes | read-only | current | The maximum number of IPv6 multicast forwarding table entries. |
| 1.3.6.1.4.1.248.12.1.2.8.31 | Nodehm2AgentPrivateVlanGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.31.1 | Tablehm2AgentPrivateVlanTable | not-accessible | current | A table of the Private VLAN configuration entries. |
| 1.3.6.1.4.1.248.12.1.2.8.31.1.1 | Rowhm2AgentPrivateVlanEntry | not-accessible | current | Represents entry for a Private VLAN. |
| 1.3.6.1.4.1.248.12.1.2.8.31.1.1.1 | Columnhm2AgentPrivateVlanType | read-write | current | Enables vlan for Private Vlan and configures private vlan type. |
| 1.3.6.1.4.1.248.12.1.2.8.31.1.1.2 | Columnhm2AgentPrivateVlanAssociate | read-write | current | This field lists all the VlanIDs which are associated with the selected vlan. If the selected vlan type is not primary(1), a zero-length bitmask is returned. |
| 1.3.6.1.4.1.248.12.1.2.8.31.2 | Tablehm2AgentPrivateVlanIntfAssocTable | not-accessible | current | A table of the Private VLAN Interface configuration entries. |
| 1.3.6.1.4.1.248.12.1.2.8.31.2.1 | Rowhm2AgentPrivateVlanIntfAssocEntry | not-accessible | current | Represents entry for a Private VLAN Interface. |
| 1.3.6.1.4.1.248.12.1.2.8.31.2.1.1 | Columnhm2AgentPrivateVlanIntfAssocHostPrimary | read-write | current | Configures the primary host vlan association with the interface. This must be configured along with hm2AgentPrivateVlanIntfAssocHostSecondary before the associ… |
| 1.3.6.1.4.1.248.12.1.2.8.31.2.1.2 | Columnhm2AgentPrivateVlanIntfAssocHostSecondary | read-write | current | Configures the secondary host vlan association with the interface. This must be configured along with hm2AgentPrivateVlanIntfAssocHostPrimary before the associ… |
| 1.3.6.1.4.1.248.12.1.2.8.31.2.1.3 | Columnhm2AgentPrivateVlanIntfAssocPromiscuousPrimary | read-write | current | Configures the primary promiscuous vlan association with the interface. This must be configured along with hm2AgentPrivateVlanIntfAssocPromiscuousSecondary bef… |
| 1.3.6.1.4.1.248.12.1.2.8.31.2.1.4 | Columnhm2AgentPrivateVlanIntfAssocPromiscuousSecondary | read-write | current | Configures the secondary promiscuous vlan association with the interface. This must be configured along with hm2AgentPrivateVlanIntfAssocPromiscuousPrimary bef… |
| 1.3.6.1.4.1.248.12.1.2.8.31.2.1.5 | Columnhm2AgentPrivateVlanIntfAssocOperational | read-only | current | Shows the operational private vlans associated with the interface. |
| 1.3.6.1.4.1.248.12.1.2.8.31.3 | Nodehm2AgentPrivateVlanSNMPExtensionGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.31.3.1 | Identityhm2AgentInvalidPrivateVlan | current | {0} VLAN cannot be used in private VLAN. | |
| 1.3.6.1.4.1.248.12.1.2.8.31.3.2 | Identityhm2AgentVlanIdAlreadyAssociated | current | VLAN already associated with a private domain. | |
| 1.3.6.1.4.1.248.12.1.2.8.31.3.3 | Identityhm2AgentPrimarySecondarySameVlans | current | Primary VLAN cannot be associated to itself. | |
| 1.3.6.1.4.1.248.12.1.2.8.31.3.4 | Identityhm2AgentMaxPrivateVlanDomain | current | Creation of the private VLAN domain was unsuccessful. Max. count of private VLAN domains reached. | |
| 1.3.6.1.4.1.248.12.1.2.8.31.3.5 | Identityhm2AgentInvalidVLANType | current | VLAN passed as {0} does not belong to type {1}. | |
| 1.3.6.1.4.1.248.12.1.2.8.31.3.6 | Identityhm2AgentSecondaryVlanAlreadyAssociated | current | Secondary VLAN already associated. | |
| 1.3.6.1.4.1.248.12.1.2.8.31.3.7 | Identityhm2AgentInvalidSwitchPortMode | current | Set the Switchport mode to {0}. | |
| 1.3.6.1.4.1.248.12.1.2.8.31.3.8 | Identityhm2AgentVlansNotAssociated | current | Cannot set {0} association. Primary and secondary VLANs are not associated. | |
| 1.3.6.1.4.1.248.12.1.2.8.31.3.9 | Identityhm2AgentInterfaceNotConfigurable | current | Interface cannot be configured. | |
| 1.3.6.1.4.1.248.12.1.2.8.31.3.10 | Identityhm2AgentVlanNotPrimaryVlanofIntf | current | VLAN is not the primary VLAN of interface. | |
| 1.3.6.1.4.1.248.12.1.2.8.31.3.11 | Identityhm2AgentVlansIDNotPresent | current | VLAN does not exist. | |
| 1.3.6.1.4.1.248.12.1.2.8.31.3.12 | Identityhm2AgentSwitchPortModeConflict | current | The switchport mode cannot be changed. The interface is already associated with {0}. | |
| 1.3.6.1.4.1.248.12.1.2.8.31.3.13 | Identityhm2AgentMoreThanOneIsolatedVlan | current | A private domain can only contain one isolated VLAN. | |
| 1.3.6.1.4.1.248.12.1.2.8.31.3.14 | Identityhm2AgentInvalidPrimaryVlan | current | Invalid {0} primary VLAN. | |
| 1.3.6.1.4.1.248.12.1.2.8.31.3.15 | Identityhm2AgentInvalidInterface | current | A private VLAN cannot be configured on the LAG interface. | |
| 1.3.6.1.4.1.248.12.1.2.8.43 | Nodehm2AgentSwitchKeepaliveGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.43.1 | Scalarhm2AgentSwitchKeepaliveState | read-write | current | The keepalive state for the switch. enable (1) - enables keepalive on the switch. disable (2) - disables keepalive on the switch. The default switch keepalive … |
| 1.3.6.1.4.1.248.12.1.2.8.43.2 | Scalarhm2AgentSwitchKeepaliveTransmitInterval | read-write | current | Transmit interval for detection PDUs. |
| 1.3.6.1.4.1.248.12.1.2.8.43.248 | Scalarhm2AgentSwitchKeepaliveRxThreshold | read-write | current | Amount of frames to be recevied until an action is taken. |
| 1.3.6.1.4.1.248.12.1.2.8.248 | Nodehm2AgentSwitchStaticMacStatsGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.248.1 | Scalarhm2AgentSwitchStaticMacEntries | read-only | current | Total number of MAC addresses configured statically in mac-filter-table. |
| 1.3.6.1.4.1.248.12.1.2.8.249 | Nodehm2AgentSwitchGARPGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.249.1 | Scalarhm2AgentSwitchGmrpUnknownMulticastFilterMode | read-write | current | This configures whether traffic from unknown multicast addresses must be flooded or be discarded. |
| 1.3.6.1.4.1.248.12.1.2.8.249.10 | Tablehm2AgentSwitchGmrpPortTable | not-accessible | current | GMRP control and status information for a bridge port. Augments dot1dPortGmrpEntry in P-BRIDGE-MIB. |
| 1.3.6.1.4.1.248.12.1.2.8.249.10.1 | Rowhm2AgentSwitchGmrpPortEntry | not-accessible | current | GMRP control and status information for a bridge port. Augments dot1dPortGmrpEntry in P-BRIDGE-MIB. |
| 1.3.6.1.4.1.248.12.1.2.8.249.10.1.1 | Columnhm2AgentSwitchGmrpPortPktRx | read-only | current | The total number of GMRP packets received, in all VLANs, on this port. |
| 1.3.6.1.4.1.248.12.1.2.8.249.10.1.2 | Columnhm2AgentSwitchGmrpPortPktTx | read-only | current | The total number of GMRP packets transmitted, in all VLANs, on this port. |
| 1.3.6.1.4.1.248.12.1.2.8.249.15 | Tablehm2AgentSwitchGvrpPortTable | not-accessible | current | GVRP control and status information for a bridge port. Augments dot1qPortVlanEntry in Q-BRIDGE-MIB. |
| 1.3.6.1.4.1.248.12.1.2.8.249.15.1 | Rowhm2AgentSwitchGvrpPortEntry | not-accessible | current | GVRP control and status information for a bridge port. Augments dot1qPortVlanEntry in Q-BRIDGE-MIB. |
| 1.3.6.1.4.1.248.12.1.2.8.249.15.1.1 | Columnhm2AgentSwitchGvrpPortPktRx | read-only | current | The total number of GVRP packets received on this port. |
| 1.3.6.1.4.1.248.12.1.2.8.249.15.1.2 | Columnhm2AgentSwitchGvrpPortPktTx | read-only | current | The total number of GVRP packets transmitted on this port. |
| 1.3.6.1.4.1.248.12.1.2.8.250 | Nodehm2AgentSwitchDVlanTagInterfaceGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.250.1 | Tablehm2AgentSwitchDVlanTagInterfaceTable | not-accessible | current | A table that holds the double vlan tagging status per interface. |
| 1.3.6.1.4.1.248.12.1.2.8.250.1.1 | Rowhm2AgentSwitchDVlanTagInterfaceEntry | not-accessible | current | A table entry specifying the double vlan tagging status per interface. |
| 1.3.6.1.4.1.248.12.1.2.8.250.1.1.1 | Columnhm2AgentSwitchDVlanTagInterfaceIfIndex | not-accessible | current | Interface ID on to which the double vlan tagging status is mapped |
| 1.3.6.1.4.1.248.12.1.2.8.250.1.1.2 | Columnhm2AgentSwitchDVlanTagInterfaceStatus | read-create | current | Controls the Double Vlan Tag status on this interface. When the value is enable(1), it becomes a core port. If at least one port has value enable(1), all other… |
| 1.3.6.1.4.1.248.12.1.2.8.260 | Nodehm2AgentSwitchConfigSNMPExtensionGroup | |||
| 1.3.6.1.4.1.248.12.1.2.8.260.1 | Identityhm2AgentSwitchConfigMacAddressNotAllowed | current | Indicates that the mac-address contains a value which is not allowed in the configuration. | |
| 1.3.6.1.4.1.248.12.1.2.8.260.2 | Identityhm2AgentSwitchConfigPortInvalid | current | Indicates that the port number/mask contains an invalid value. | |
| 1.3.6.1.4.1.248.12.1.2.10 | Nodehm2AgentPortMirroringGroup | |||
| 1.3.6.1.4.1.248.12.1.2.10.4 | Tablehm2AgentPortMirrorTable | not-accessible | current | This table includes entries for each Port Mirroring session. |
| 1.3.6.1.4.1.248.12.1.2.10.4.1 | Rowhm2AgentPortMirrorEntry | not-accessible | current | Provides configuration of a Port Mirroring session specifying the destination port, and the source Port Mask, providing a many-to-one mapping. |
| 1.3.6.1.4.1.248.12.1.2.10.4.1.1 | Columnhm2AgentPortMirrorSessionNum | not-accessible | current | The Session number of this mirroring entry. The number of sessions is fixed and platform dependant. |
| 1.3.6.1.4.1.248.12.1.2.10.4.1.2 | Columnhm2AgentPortMirrorDestinationPort | read-write | current | The port which traffic from the mirrored ports will be sent to. |
| 1.3.6.1.4.1.248.12.1.2.10.4.1.3 | Columnhm2AgentPortMirrorSourcePortMask | read-write | current | The ports from which traffic will be sent to the destination port. The destination port can not be included in this list of ports. |
| 1.3.6.1.4.1.248.12.1.2.10.4.1.4 | Columnhm2AgentPortMirrorAdminMode | read-write | current | The status of this port mirroring session. enable(1) - This session is active and all traffic from the source ports will be mirrored to the destination port. d… |
| 1.3.6.1.4.1.248.12.1.2.10.4.1.5 | Columnhm2AgentPortMirrorSourceVlan | read-write | current | The vlan from which traffic will be sent to the destination port. |
| 1.3.6.1.4.1.248.12.1.2.10.4.1.6 | Columnhm2AgentPortMirrorRemoteSourceVlan | read-write | current | The remote vlan from which traffic will be sent to the destination port. |
| 1.3.6.1.4.1.248.12.1.2.10.4.1.7 | Columnhm2AgentPortMirrorRemoteDestinationVlan | read-write | current | The VLAN that forwards the network traffic to the destination switch. |
| 1.3.6.1.4.1.248.12.1.2.10.4.1.8 | Columnhm2AgentPortMirrorReflectorPort | read-write | current | The port which traffic from the mirrored ports will be sent to in case of destination being remote VLAN. |
| 1.3.6.1.4.1.248.12.1.2.10.4.1.9 | Columnhm2AgentPortMirrorAllowMgmtMode | read-write | current | The status of the management access possibility for this session. enable(1) - Management is allowed - The device is accessible via this port and is responsive … |
| 1.3.6.1.4.1.248.12.1.2.10.4.1.248 | Columnhm2AgentPortMirrorReset | read-write | current | Removes, reset(2) the configuration for this session. Returns always other(1) when read. |
| 1.3.6.1.4.1.248.12.1.2.10.4.1.249 | Columnhm2AgentPortMirrorDestinationPortSecondary | read-write | current | The secondary port which traffic from the mirrored ports will be sent to. |
| 1.3.6.1.4.1.248.12.1.2.10.5 | Tablehm2AgentPortMirrorTypeTable | not-accessible | current | This table includes entries for each source ports direction of port mirroring. |
| 1.3.6.1.4.1.248.12.1.2.10.5.1 | Rowhm2AgentPortMirrorTypeEntry | not-accessible | current | Provides configuration of a Port Mirroring direction specifying the session of the port mirroring and source port. |
| 1.3.6.1.4.1.248.12.1.2.10.5.1.1 | Columnhm2AgentPortMirrorTypeSourcePort | not-accessible | current | The port from which traffic will be sent to the destination port. This port should be a source port in the corresponding session. |
| 1.3.6.1.4.1.248.12.1.2.10.5.1.2 | Columnhm2AgentPortMirrorTypeType | read-write | current | The direction of the data to be mirrored on this source port. none(0) - No configuration is set. tx(1) - The data that is transmitted from the source port. rx(… |
| 1.3.6.1.4.1.248.12.1.2.10.6 | Scalarhm2AgentPortMirrorRemoteVlan | read-write | current | The VLAN configured as RSPAN VLAN. |
| 1.3.6.1.4.1.248.12.1.2.10.248 | Nodehm2AgentPortMirrorSNMPExtensionGroup | |||
| 1.3.6.1.4.1.248.12.1.2.10.248.1 | Identityhm2AgentPortMirrorVlanMirrorPortConflict | current | VLAN has been already configured as a source interface. At the same time physical interface and VLAN interface cannot be configured as source interfaces for a … | |
| 1.3.6.1.4.1.248.12.1.2.10.248.2 | Identityhm2AgentPortMirrorPortVlanMirrorConflict | current | A physical interface has been already configured as a source interface. At the same time physical interface and VLAN interface cannot be configured as source i… | |
| 1.3.6.1.4.1.248.12.1.2.10.248.3 | Identityhm2AgentPortMirrorProbePortAlreadySet | current | Selected interface is already used. | |
| 1.3.6.1.4.1.248.12.1.2.10.248.4 | Identityhm2AgentPortMirrorProbePortVlanConflict | current | Destination interface cannot participate in source VLAN. | |
| 1.3.6.1.4.1.248.12.1.2.10.248.5 | Identityhm2AgentPortMirrorVlanNotCreated | current | Not existing VLAN cannot be configured as source interface for a session. | |
| 1.3.6.1.4.1.248.12.1.2.10.248.6 | Identityhm2AgentPortMirrorInvalidSourcePort | current | Selected interface () cannot be configured as source interface. | |
| 1.3.6.1.4.1.248.12.1.2.10.248.7 | Identityhm2AgentPortMirrorSourcePortDestinationPortConflict | current | Destination interface () cannot be configured as source interface. | |
| 1.3.6.1.4.1.248.12.1.2.10.248.8 | Identityhm2AgentPortMirrorDestinationPortInvalid | current | Conflict with another feature: Selected interface () is already used by () and cannot be configured as a destination interface. | |
| 1.3.6.1.4.1.248.12.1.2.10.248.9 | Identityhm2AgentPortMirrorVlanRspanVlanConflict | current | RSPAN vlan () cannot be configured as source vlan. | |
| 1.3.6.1.4.1.248.12.1.2.10.248.10 | Identityhm2AgentPortMirrorRemoteSourceRemoteDestinationConflict | current | Source and destination cannot be set to remote VLAN at the same time. | |
| 1.3.6.1.4.1.248.12.1.2.10.248.11 | Identityhm2AgentPortMirrorReflectorPortInvalid | current | Selected interface () cannot be configured as a reflector interface. Only physical interface can be configured as a reflector interface. | |
| 1.3.6.1.4.1.248.12.1.2.10.248.12 | Identityhm2AgentPortMirrorSourcePortReflectorPortConflict | current | Source interface () cannot be configured as reflector interface. | |
| 1.3.6.1.4.1.248.12.1.2.10.248.13 | Identityhm2AgentPortMirrorReflectorPortVlanConflict | current | Reflector interface () cannot participate in source vlan (). | |
| 1.3.6.1.4.1.248.12.1.2.10.248.14 | Identityhm2AgentPortMirrorPrivateVlanConfigured | current | Selected VLAN is already configured as private VLAN and cannot be configured as RSPAN VLAN. | |
| 1.3.6.1.4.1.248.12.1.2.10.248.15 | Identityhm2AgentPortMirrorDestinationRemotePortNotSet | current | A destination/reflector port must first be set before mirroring/remote-mirroring can be enabled. | |
| 1.3.6.1.4.1.248.12.1.2.10.248.16 | Identityhm2AgentPortMirrorRspanVlanInconsistent | current | The RSPAN VLAN ID is inconsistent with the RSPAN source/destination VLAN ID. | |
| 1.3.6.1.4.1.248.12.1.2.10.248.17 | Identityhm2AgentPortMirrorRspanVlanIdInvalid | current | VLAN 1 cannot be used as the RSPAN VLAN. | |
| 1.3.6.1.4.1.248.12.1.2.10.248.18 | Identityhm2AgentPortMirrorSourcePortSettingConflict | current | Source Port mirror can not be configured. | |
| 1.3.6.1.4.1.248.12.1.2.10.248.19 | Identityhm2AgentPortMirrorDestinationPortSettingConflict | current | Destination Port mirror can not be configured. | |
| 1.3.6.1.4.1.248.12.1.2.10.248.20 | Identityhm2AgentVlanInvalidSubnet | current | Invalid subnet cannot be added. | |
| 1.3.6.1.4.1.248.12.1.2.10.248.21 | Identityhm2AgentPortMirrorSecondaryPortDestinationNotSupported | current | Vlan mirroring and RSPAN are not supported on second probe port. | |
| 1.3.6.1.4.1.248.12.1.2.10.248.22 | Identityhm2AgentPortMirrorTxOverUnitBoundaryNotSupported | current | TX mirroring accross unit boundaries is not supported. | |
| 1.3.6.1.4.1.248.12.1.2.12 | Tablehm2AgentDot3adAggPortTable | not-accessible | current | This table provides 802.3ad link aggregation information for each physical port that is not available through the standard MIB. |
| 1.3.6.1.4.1.248.12.1.2.12.1 | Rowhm2AgentDot3adAggPortEntry | not-accessible | current | Information about a table entry. The hm2AgentDot3adAggPort identifies the external interface number of the port. |
| 1.3.6.1.4.1.248.12.1.2.12.1.1 | Columnhm2AgentDot3adAggPort | read-only | current | ifIndex of this physical port |
| 1.3.6.1.4.1.248.12.1.2.12.1.2 | Columnhm2AgentDot3adAggPortLACPMode | read-write | current | Enable/disable 802.3ad LACP on this port |
| 1.3.6.1.4.1.248.12.1.2.13 | Tablehm2AgentPortConfigTable | not-accessible | current | A table of the switch's physical port config entries |
| 1.3.6.1.4.1.248.12.1.2.13.1 | Rowhm2AgentPortConfigEntry | not-accessible | current | Switch's physical port config entry |
| 1.3.6.1.4.1.248.12.1.2.13.1.1 | Columnhm2AgentPortDot1dBasePort | read-only | current | The number of this port. |
| 1.3.6.1.4.1.248.12.1.2.13.1.2 | Columnhm2AgentPortIfIndex | read-only | current | The switchs Port IfIndex. |
| 1.3.6.1.4.1.248.12.1.2.13.1.10 | Columnhm2AgentPortClearStats | read-write | current | Clear stats for this port only. |
| 1.3.6.1.4.1.248.12.1.2.13.1.14 | Columnhm2AgentPortDot3FlowControlMode | read-write | current | Config flowcontrol allows you to enable or disable 802.3x flow control for this port. This value applies to only full-duplex mode ports. Enabling symmetric flo… |
| 1.3.6.1.4.1.248.12.1.2.13.1.18 | Columnhm2AgentPortMaxFrameSizeLimit | read-only | current | This object identifies the largest value that can be configured for hm2AgentPortMaxFrameSize. |
| 1.3.6.1.4.1.248.12.1.2.13.1.19 | Columnhm2AgentPortMaxFrameSize | read-write | current | This object identifies the currently configured maximum frame size value for this port. The maximum value that this object can be set to is the value of hm2Age… |
| 1.3.6.1.4.1.248.12.1.2.13.1.20 | Columnhm2AgentPortBroadcastControlMode | read-write | current | If enabled, broadcast storm recovery will function on this port. When you specify Enable for Broadcast Storm Recovery and the broadcast traffic on this Etherne… |
| 1.3.6.1.4.1.248.12.1.2.13.1.21 | Columnhm2AgentPortBroadcastControlThreshold | read-write | current | Configures the broadcast storm recovery threshold for this port as a percentage of port speed or as an absolute pps rate. |
| 1.3.6.1.4.1.248.12.1.2.13.1.22 | Columnhm2AgentPortMulticastControlMode | read-write | current | If enabled, multicast storm recovery will function on this port. When you specify Enable for Multicast Storm Recovery and the multicast traffic on this Etherne… |
| 1.3.6.1.4.1.248.12.1.2.13.1.23 | Columnhm2AgentPortMulticastControlThreshold | read-write | current | Configures the multicast storm recovery threshold for this port as a percentage of port speed or as an absolute pps rate. |
| 1.3.6.1.4.1.248.12.1.2.13.1.24 | Columnhm2AgentPortUnicastControlMode | read-write | current | If enabled, unicast storm recovery will function on this port. When you specify Enable for Unicast Storm Recovery and the unknown unicast traffic on this Ether… |
| 1.3.6.1.4.1.248.12.1.2.13.1.25 | Columnhm2AgentPortUnicastControlThreshold | read-write | current | Configures the unicast storm recovery threshold for this port as a percentage of port speed or as an absolute pps rate. |
| 1.3.6.1.4.1.248.12.1.2.13.1.26 | Columnhm2AgentPortBroadcastControlThresholdUnit | read-write | current | Configures the units of the threshold value to percentage of port speed or absolute packets per second. |
| 1.3.6.1.4.1.248.12.1.2.13.1.27 | Columnhm2AgentPortMulticastControlThresholdUnit | read-write | current | Configures the units of the threshold value to percentage of port speed or absolute packets per second. |
| 1.3.6.1.4.1.248.12.1.2.13.1.28 | Columnhm2AgentPortUnicastControlThresholdUnit | read-write | current | Configures the units of the threshold value to percentage of port speed or absolute packets per second. |
| 1.3.6.1.4.1.248.12.1.2.13.1.29 | Columnhm2AgentPortVoiceVlanMode | read-write | current | Describes and Configures the Port Voice VLAN Mode. This object can only be set to disable(5). |
| 1.3.6.1.4.1.248.12.1.2.13.1.30 | Columnhm2AgentPortVoiceVlanID | read-write | current | Describes and Configures the Port Voice VLAN ID if the Voice Vlan Mode is Vlan ID. 0 can not be set. |
| 1.3.6.1.4.1.248.12.1.2.13.1.31 | Columnhm2AgentPortVoiceVlanPriority | read-write | current | Describes and Configures the Port Voice VLAN Priority if the Voice Vlan Mode is dot1p. A value of 255 indicates that the priority is not configured. |
| 1.3.6.1.4.1.248.12.1.2.13.1.32 | Columnhm2AgentPortVoiceVlanDataPriorityMode | read-write | current | Describes and Configures the Port Voice VLAN Data Priority Mode. |
| 1.3.6.1.4.1.248.12.1.2.13.1.33 | Columnhm2AgentPortVoiceVlanOperationalStatus | read-only | current | Describes the Port Voice VLAN Operational Status. |
| 1.3.6.1.4.1.248.12.1.2.13.1.34 | Columnhm2AgentPortVoiceVlanUntagged | read-write | current | Describes and Configures the Port Voice VLAN tagging mode. |
| 1.3.6.1.4.1.248.12.1.2.13.1.35 | Columnhm2AgentPortVoiceVlanNoneMode | read-write | current | Describes and Configures the Port Voice VLAN None mode. |
| 1.3.6.1.4.1.248.12.1.2.13.1.36 | Columnhm2AgentPortVoiceVlanDSCP | read-write | current | Describes and Configures the Port Voice VLAN DSCP value. |
| 1.3.6.1.4.1.248.12.1.2.13.1.37 | Columnhm2AgentPortVoiceVlanAuthMode | read-write | current | Describes and Configures the Port Voice VLAN Authentication mode. Disable means authentication not required for voice devices when dot1x is enabled. |
| 1.3.6.1.4.1.248.12.1.2.13.1.38 | Columnhm2AgentPortDot3FlowControlOperStatus | read-only | current | This object identifies operational status of the flow control per port. |
| 1.3.6.1.4.1.248.12.1.2.13.1.45 | Columnhm2AgentPortSwitchportMode | read-write | current | Different types of Switchport modes. |
| 1.3.6.1.4.1.248.12.1.2.13.1.248 | Columnhm2AgentPortSfpLinkLossAlert | read-write | current | If enabled, this object helps in the detecting the loss of a SFP link by deactivating its light. |
| 1.3.6.1.4.1.248.12.1.2.14 | Nodehm2AgentProtocolConfigGroup | |||
| 1.3.6.1.4.1.248.12.1.2.14.2 | Tablehm2AgentProtocolGroupTable | not-accessible | current | A table of the switch's Protocol-based VLAN entries |
| 1.3.6.1.4.1.248.12.1.2.14.2.1 | Rowhm2AgentProtocolGroupEntry | not-accessible | current | Switch's Protocol-based VLAN entry |
| 1.3.6.1.4.1.248.12.1.2.14.2.1.1 | Columnhm2AgentProtocolGroupId | not-accessible | current | Group identifier of the Protocol-based VLAN entry. |
| 1.3.6.1.4.1.248.12.1.2.14.2.1.2 | Columnhm2AgentProtocolGroupName | read-write | current | Group name of the Protocol-based VLAN entry. |
| 1.3.6.1.4.1.248.12.1.2.14.2.1.3 | Columnhm2AgentProtocolGroupVlanId | read-write | current | VLAN associated with the Protocol-based VLAN entry. Set to 0 to remove. |
| 1.3.6.1.4.1.248.12.1.2.14.2.1.7 | Columnhm2AgentProtocolGroupStatus | read-create | current | The status of the Protocol-based VLAN entry. active(1) - this entry is active createAndGo(4) - used to create a new entry destroy(6) - remove this entry |
| 1.3.6.1.4.1.248.12.1.2.14.3 | Tablehm2AgentProtocolGroupPortTable | not-accessible | current | A table of the switch's physical port config entries |
| 1.3.6.1.4.1.248.12.1.2.14.3.1 | Rowhm2AgentProtocolGroupPortEntry | not-accessible | current | Switch's physical port config entry |
| 1.3.6.1.4.1.248.12.1.2.14.3.1.1 | Columnhm2AgentProtocolGroupPortIfIndex | read-only | current | The interface number of this instance. |
| 1.3.6.1.4.1.248.12.1.2.14.3.1.2 | Columnhm2AgentProtocolGroupPortStatus | read-create | current | The status of this entry. active(1) - the port is associated with this group createAndGo(4) - add the port to this group createAndWait(5) - add the port to thi… |
| 1.3.6.1.4.1.248.12.1.2.14.4 | Tablehm2AgentProtocolGroupProtocolTable | not-accessible | current | A table of the switch's physical port config entries |
| 1.3.6.1.4.1.248.12.1.2.14.4.1 | Rowhm2AgentProtocolGroupProtocolEntry | not-accessible | current | Switch's physical port config entry |
| 1.3.6.1.4.1.248.12.1.2.14.4.1.1 | Columnhm2AgentProtocolGroupProtocolID | not-accessible | current | The protocol ID of this instance. The value for IP is 2048 (0x0800), ARP is 2054 (0x0806) and IPX is 33079 (0x8137). Other protocol Ids in the range 1536 to 65… |
| 1.3.6.1.4.1.248.12.1.2.14.4.1.2 | Columnhm2AgentProtocolGroupProtocolStatus | read-create | current | The status of this entry. active(1) - the port is associated with this group createAndGo(4) - add the port to this group createAndWait(5) - add the port to thi… |
| 1.3.6.1.4.1.248.12.1.2.15 | Nodehm2AgentStpSwitchConfigGroup | |||
| 1.3.6.1.4.1.248.12.1.2.15.1 | Scalarhm2AgentStpConfigDigestKey | read-only | current | The MST configuration digest key. |
| 1.3.6.1.4.1.248.12.1.2.15.2 | Scalarhm2AgentStpConfigFormatSelector | read-only | current | The MST configuration format selector. A value other than 0 (zero) indicates non-support for the IEEE 802.1s standard. |
| 1.3.6.1.4.1.248.12.1.2.15.3 | Scalarhm2AgentStpConfigName | read-write | current | The MST configuration name of at most 32 characters. |
| 1.3.6.1.4.1.248.12.1.2.15.4 | Scalarhm2AgentStpConfigRevision | read-write | current | The MST configuration revision. The default value is 1. |
| 1.3.6.1.4.1.248.12.1.2.15.5 | Scalarhm2AgentStpForceVersion | read-write | current | The MST configuration force protocol version. The default version is RSTP. |
| 1.3.6.1.4.1.248.12.1.2.15.6 | Scalarhm2AgentStpAdminMode | read-write | current | The spanning tree operational status. enable(1) - enables spanning tree operational status on the switch. disable(2) - disables spanning tree operational statu… |
| 1.3.6.1.4.1.248.12.1.2.15.7 | Tablehm2AgentStpPortTable | not-accessible | current | STP port table. |
| 1.3.6.1.4.1.248.12.1.2.15.7.1 | Rowhm2AgentStpPortEntry | not-accessible | current | STP port entry. |
| 1.3.6.1.4.1.248.12.1.2.15.7.1.1 | Columnhm2AgentStpPortState | read-write | current | The administrative STP state for the port. enable(1) - enables STP on the port. disable(2) - disables STP on the port. The default port STP state is enabled fo… |
| 1.3.6.1.4.1.248.12.1.2.15.7.1.2 | Columnhm2AgentStpPortStatsMstpBpduRx | read-only | current | The MSTP BPDUs received on a specific port. |
| 1.3.6.1.4.1.248.12.1.2.15.7.1.3 | Columnhm2AgentStpPortStatsMstpBpduTx | read-only | current | The MSTP BPDUs sent from a specific port. |
| 1.3.6.1.4.1.248.12.1.2.15.7.1.4 | Columnhm2AgentStpPortStatsRstpBpduRx | read-only | current | The RSTP BPDUs received on a specific port. |
| 1.3.6.1.4.1.248.12.1.2.15.7.1.5 | Columnhm2AgentStpPortStatsRstpBpduTx | read-only | current | The RSTP BPDUs sent from a specific port. |
| 1.3.6.1.4.1.248.12.1.2.15.7.1.6 | Columnhm2AgentStpPortStatsStpBpduRx | read-only | current | The STP BPDUs received on a specific port. |
| 1.3.6.1.4.1.248.12.1.2.15.7.1.7 | Columnhm2AgentStpPortStatsStpBpduTx | read-only | current | The STP BPDUs sent from a specific port. |
| 1.3.6.1.4.1.248.12.1.2.15.7.1.8 | Columnhm2AgentStpPortUpTime | read-only | current | Time since port was reset. It is displayed in days, hours, minutes, and seconds. |
| 1.3.6.1.4.1.248.12.1.2.15.7.1.9 | Columnhm2AgentStpPortMigrationCheck | read-write | current | Force the specified port to transmit RSTP or MSTP BPDUs. Supported values: false(0) - BPDUs are not to be transmitted. true(1) - BPDUs are to be transmitted A … |
| 1.3.6.1.4.1.248.12.1.2.15.8 | Nodehm2AgentStpCstConfigGroup | |||
| 1.3.6.1.4.1.248.12.1.2.15.8.1 | Scalarhm2AgentStpCstHelloTime | read-only | current | The MSTP root port hello time for the CIST. |
| 1.3.6.1.4.1.248.12.1.2.15.8.2 | Scalarhm2AgentStpCstMaxAge | read-only | current | The MSTP root port max age for the CIST. |
| 1.3.6.1.4.1.248.12.1.2.15.8.3 | Scalarhm2AgentStpCstRegionalRootId | read-only | current | The MSTP regional root identifier for the CIST. |
| 1.3.6.1.4.1.248.12.1.2.15.8.4 | Scalarhm2AgentStpCstRegionalRootPathCost | read-only | current | The MSTP regional root path cost for the CIST. |
| 1.3.6.1.4.1.248.12.1.2.15.8.5 | Scalarhm2AgentStpCstRootFwdDelay | read-only | current | The MSTP root port forward delay for the CIST. |
| 1.3.6.1.4.1.248.12.1.2.15.8.6 | Scalarhm2AgentStpCstBridgeFwdDelay | read-write | current | The MSTP bridge forward delay for the CIST. The default value is 15. |
| 1.3.6.1.4.1.248.12.1.2.15.8.7 | Scalarhm2AgentStpCstBridgeHelloTime | read-write | current | The MSTP bridge hello time for the CIST. The default value is 2. |
| 1.3.6.1.4.1.248.12.1.2.15.8.8 | Scalarhm2AgentStpCstBridgeHoldTime | read-only | current | The MSTP bridge hold time for the CIST. |
| 1.3.6.1.4.1.248.12.1.2.15.8.9 | Scalarhm2AgentStpCstBridgeMaxAge | read-write | current | The MSTP bridge max age for the CIST. The default value is 20. |
| 1.3.6.1.4.1.248.12.1.2.15.8.10 | Scalarhm2AgentStpCstBridgeMaxHops | read-write | current | The MSTP bridge max hops for the CIST. The default value is 20. |
| 1.3.6.1.4.1.248.12.1.2.15.8.11 | Scalarhm2AgentStpCstBridgePriority | read-write | current | The MSTP bridge priority for the CIST. The default value is 32768. |
| 1.3.6.1.4.1.248.12.1.2.15.8.12 | Scalarhm2AgentStpCstBridgeHoldCount | read-write | current | The MSTP bridge hold count for the CIST. This command sets the value of maximum bpdus that a bridge is allowed to send within a hello time window. The default … |
| 1.3.6.1.4.1.248.12.1.2.15.9 | Tablehm2AgentStpCstPortTable | not-accessible | current | CIST port table. |
| 1.3.6.1.4.1.248.12.1.2.15.9.1 | Rowhm2AgentStpCstPortEntry | not-accessible | current | CIST port entry. |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.1 | Columnhm2AgentStpCstPortOperEdge | read-only | current | The MSTP operational status of a specific port for the CIST. |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.2 | Columnhm2AgentStpCstPortOperPointToPoint | read-only | current | The MSTP operational point to point mac of a specific port for the CIST. |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.3 | Columnhm2AgentStpCstPortTopologyChangeAck | read-only | current | The MSTP topology change acknowledge for a specific port in the CIST. |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.4 | Columnhm2AgentStpCstPortEdge | read-write | current | The administrative state of a specific port in CIST. enable(1) - enables the port. disable(2) - disables the port. The default port state is disabled. |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.5 | Columnhm2AgentStpCstPortForwardingState | read-only | current | The MSTP forwarding state of a specific port in CIST. |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.6 | Columnhm2AgentStpCstPortId | read-only | current | The MSTP port identifier of a specific port in CIST. |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.7 | Columnhm2AgentStpCstPortPathCost | read-write | current | The MSTP port path cost in CIST. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link s… |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.8 | Columnhm2AgentStpCstPortPriority | read-write | current | The MSTP port priority in CIST. The priority is in the increments of 16. The default value is 128. |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.9 | Columnhm2AgentStpCstDesignatedBridgeId | read-only | current | The MSTP designated bridge ID of a specific port in CIST. |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.10 | Columnhm2AgentStpCstDesignatedCost | read-only | current | The MSTP designated cost of a specific port in CIST. |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.11 | Columnhm2AgentStpCstDesignatedPortId | read-only | current | The MSTP designated port ID of a specific port in CIST. |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.12 | Columnhm2AgentStpCstExtPortPathCost | read-write | current | The MSTP external port path cost in CIST. The default value varies depending upon the link speed. |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.13 | Columnhm2AgentStpCstPortBpduGuardEffect | read-only | current | BPDU Guard Mode effect on the port. enable(1) - BPDU Guard Mode is enabled on the port. disable(2) - BPDU Guard Mode is disabled on the port. |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.14 | Columnhm2AgentStpCstPortBpduFilter | read-write | current | This command sets BPDU Filter mode on the port. enable(1) - BPDU Filter Mode is enabled on the port. disable(2) - BPDU Filter Mode is disabled on the port. |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.15 | Columnhm2AgentStpCstPortBpduFlood | read-write | current | This command sets BPDU Flood mode on the port. enable(1) - BPDU Flood Mode is enabled on the port. disable(2) - BPDU Flood Mode is disabled on the port. |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.16 | Columnhm2AgentStpCstPortAutoEdge | read-write | current | This command sets the auto-edge mode of the port which enables it to become an edge port if it does not see BPDUs for some duration. enable(1) - enables the au… |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.17 | Columnhm2AgentStpCstPortRootGuard | read-write | current | This command sets a port to discard any superior information received by the port and thus protect against root of the device from changing.The port gets put i… |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.18 | Columnhm2AgentStpCstPortTCNGuard | read-write | current | This command restricts the port from propagating any topology change information received through that port. enable(1) - enables the TCN guard mode for the por… |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.19 | Columnhm2AgentStpCstPortLoopGuard | read-write | current | This command enables loop guard on this port. This setting applies to all Spanning Tree instances of which this port is a member. enable(1) - enables the loop … |
| 1.3.6.1.4.1.248.12.1.2.15.9.1.248 | Columnhm2AgentStpCstPortBpduFilterState | read-only | current | This command displays the BPDU Filter state on the port. enable(1) - BPDU Filter Mode is active on the port. disable(2) - BPDU Filter Mode is inactive on the p… |
| 1.3.6.1.4.1.248.12.1.2.15.10 | Tablehm2AgentStpMstTable | not-accessible | current | MST table. |
| 1.3.6.1.4.1.248.12.1.2.15.10.1 | Rowhm2AgentStpMstEntry | not-accessible | current | MST entry. |
| 1.3.6.1.4.1.248.12.1.2.15.10.1.1 | Columnhm2AgentStpMstId | read-only | current | The MSTP instance ID. |
| 1.3.6.1.4.1.248.12.1.2.15.10.1.2 | Columnhm2AgentStpMstBridgePriority | read-write | current | The MSTP bridge priority in a specific instance. The priority is in the increments of 4096. The recommended default value is 32768. |
| 1.3.6.1.4.1.248.12.1.2.15.10.1.3 | Columnhm2AgentStpMstBridgeIdentifier | read-only | current | The MSTP bridge identifier in a specific instance. |
| 1.3.6.1.4.1.248.12.1.2.15.10.1.4 | Columnhm2AgentStpMstDesignatedRootId | read-only | current | The MSTP designated root bridge identifier in a specific instance. |
| 1.3.6.1.4.1.248.12.1.2.15.10.1.5 | Columnhm2AgentStpMstRootPathCost | read-only | current | The MSTP root path cost in a specific instance. |
| 1.3.6.1.4.1.248.12.1.2.15.10.1.6 | Columnhm2AgentStpMstRootPortId | read-only | current | The MSTP root port ID in a specific instance. |
| 1.3.6.1.4.1.248.12.1.2.15.10.1.7 | Columnhm2AgentStpMstTimeSinceTopologyChange | read-only | current | The MSTP time since the last topology change in a specific instance. |
| 1.3.6.1.4.1.248.12.1.2.15.10.1.8 | Columnhm2AgentStpMstTopologyChangeCount | read-only | current | The MSTP count of topology changes in a specific instance. |
| 1.3.6.1.4.1.248.12.1.2.15.10.1.9 | Columnhm2AgentStpMstTopologyChangeParm | read-only | current | The MSTP topology change parameter in a specific instance. |
| 1.3.6.1.4.1.248.12.1.2.15.10.1.10 | Columnhm2AgentStpMstRowStatus | read-create | current | The MSTP instance status. Supported values: active(1) - valid instance. notReady(3) - row has incomplete values. createAndGo(4) - used to create a new instance… |
| 1.3.6.1.4.1.248.12.1.2.15.11 | Tablehm2AgentStpMstPortTable | not-accessible | current | MST port table. |
| 1.3.6.1.4.1.248.12.1.2.15.11.1 | Rowhm2AgentStpMstPortEntry | not-accessible | current | MST port entry. |
| 1.3.6.1.4.1.248.12.1.2.15.11.1.1 | Columnhm2AgentStpMstPortForwardingState | read-only | current | The MSTP forwarding state of a specific port in a specific instance. |
| 1.3.6.1.4.1.248.12.1.2.15.11.1.2 | Columnhm2AgentStpMstPortId | read-only | current | The MSTP port identifier of a specific port in a specific instance. |
| 1.3.6.1.4.1.248.12.1.2.15.11.1.3 | Columnhm2AgentStpMstPortPathCost | read-write | current | The MSTP port path cost in a specific instance. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depend… |
| 1.3.6.1.4.1.248.12.1.2.15.11.1.4 | Columnhm2AgentStpMstPortPriority | read-write | current | The MSTP port priority in a specific instance. The priority is in the increments of 16. The default value is 128. |
| 1.3.6.1.4.1.248.12.1.2.15.11.1.5 | Columnhm2AgentStpMstDesignatedBridgeId | read-only | current | The MSTP designated bridge ID of a specific port in a specific instance. |
| 1.3.6.1.4.1.248.12.1.2.15.11.1.6 | Columnhm2AgentStpMstDesignatedCost | read-only | current | The MSTP designated cost of a specific port in a specific instance. |
| 1.3.6.1.4.1.248.12.1.2.15.11.1.7 | Columnhm2AgentStpMstDesignatedPortId | read-only | current | The MSTP designated port ID of a specific port in a specific instance. |
| 1.3.6.1.4.1.248.12.1.2.15.11.1.8 | Columnhm2AgentStpMstPortLoopInconsistentState | read-only | current | The loop inconsistent state of a specific port in a specific instance. This value can only report as true(1) when loop guard is enabled on the port and the por… |
| 1.3.6.1.4.1.248.12.1.2.15.11.1.9 | Columnhm2AgentStpMstPortTransitionsIntoLoopInconsistentState | read-only | current | The number of times this interface has transitioned into loop inconsistent state. |
| 1.3.6.1.4.1.248.12.1.2.15.11.1.10 | Columnhm2AgentStpMstPortTransitionsOutOfLoopInconsistentState | read-only | current | The number of times this interface has transitioned out of loop inconsistent state. |
| 1.3.6.1.4.1.248.12.1.2.15.11.1.248 | Columnhm2AgentStpMstPortRole | read-only | current | The current port pole for a specific port (i.e., root, alternate, designated or backup) in a specific instance. |
| 1.3.6.1.4.1.248.12.1.2.15.11.1.249 | Columnhm2AgentStpCstAutoPortPathCost | read-only | current | The Spanning Tree auto port path cost. If the value is true, the port path cost will be calculated depending on link speed corresponding to the recommendation … |
| 1.3.6.1.4.1.248.12.1.2.15.11.1.250 | Columnhm2AgentStpMstPortReceivedBridgeId | read-only | current | The received bridge ID on a specific port in a specific instance. |
| 1.3.6.1.4.1.248.12.1.2.15.11.1.251 | Columnhm2AgentStpMstPortReceivedRPC | read-only | current | The received root path cost of a specific port in a specific instance. |
| 1.3.6.1.4.1.248.12.1.2.15.11.1.252 | Columnhm2AgentStpMstPortReceivedPortId | read-only | current | The received port ID on a specific port in a specific instance. |
| 1.3.6.1.4.1.248.12.1.2.15.11.1.253 | Columnhm2AgentStpMstAutoPortPathCost | read-only | current | The Spanning Tree auto port path cost of a given instance. If the value is true, the port path cost will be calculated depending on link speed corresponding to… |
| 1.3.6.1.4.1.248.12.1.2.15.11.1.254 | Columnhm2AgentStpMstPortReceivedRegionalRPC | read-only | current | The received regional (internal) root path cost of a specific port in a specific instance. |
| 1.3.6.1.4.1.248.12.1.2.15.12 | Tablehm2AgentStpMstVlanTable | not-accessible | current | MST VLAN table. |
| 1.3.6.1.4.1.248.12.1.2.15.12.1 | Rowhm2AgentStpMstVlanEntry | not-accessible | current | MST VLAN entry. |
| 1.3.6.1.4.1.248.12.1.2.15.12.1.1 | Columnhm2AgentStpMstVlanRowStatus | read-create | current | The association status of an MSTP instance and a VLAN. Supported values: active(1) - valid association between an MSTP instance and a VLAN. notReady(3) - incon… |
| 1.3.6.1.4.1.248.12.1.2.15.13 | Scalarhm2AgentStpBpduGuardMode | read-write | current | The spanning tree BPDU Guard Mode. enable(1) - enables BPDU Guard Mode on the switch. disable(2) - disables BPDU Guard Mode on the switch. The default status i… |
| 1.3.6.1.4.1.248.12.1.2.15.14 | Scalarhm2AgentStpBpduFilterDefault | read-write | current | The spanning tree BPDU Filter Mode, it enables BPDU Filter on all edge ports. enable(1) - enables BPDU Filter Mode on the switch. disable(2) - disables BPDU Fi… |
| 1.3.6.1.4.1.248.12.1.2.15.248 | Scalarhm2AgentStpRingOnlyMode | read-write | current | When RSTP Ring Only Mode is enabled the switch ignores the BPDUs age on Ring Only Mode ports. The topology change BPDUs sent on Ring Only Mode ports will have … |
| 1.3.6.1.4.1.248.12.1.2.15.249 | Scalarhm2AgentStpRingOnlyModeIntfOne | read-write | current | Interface index of the first interface. |
| 1.3.6.1.4.1.248.12.1.2.15.250 | Scalarhm2AgentStpRingOnlyModeIntfTwo | read-write | current | Interface index of the second interface. |
| 1.3.6.1.4.1.248.12.1.2.15.251 | Scalarhm2AgentStpTrapMode | read-write | current | The spanning tree trap status. enable(1) - enables spanning tree traps on the switch. disable(2) - disables spanning tree traps on the switch. The default stat… |
| 1.3.6.1.4.1.248.12.1.2.15.260 | Nodehm2AgentStpMstSNMPExtensionGroup | |||
| 1.3.6.1.4.1.248.12.1.2.15.260.1 | Identityhm2AgentStpMstInstanceVlanErrorReturn | current | Invalid value for instance. Instance 0 is a system managed instance and the user should not modify it. | |
| 1.3.6.1.4.1.248.12.1.2.15.260.2 | Identityhm2AgentStpCstFwdDelayErrorReturn | current | Invalid value combination for Max Age/Forward Delay. | |
| 1.3.6.1.4.1.248.12.1.2.15.260.3 | Identityhm2AgentStpMstSwitchVersionConflict | current | Cannot switch version while spanning-tree is disabled. | |
| 1.3.6.1.4.1.248.12.1.2.17 | Nodehm2AgentClassOfServiceGroup | |||
| 1.3.6.1.4.1.248.12.1.2.17.1 | Tablehm2AgentClassOfServicePortTable | not-accessible | current | A table that contains information about the 802.1p priority mapping to traffic class priority queue for every physical port. |
| 1.3.6.1.4.1.248.12.1.2.17.1.1 | Rowhm2AgentClassOfServicePortEntry | not-accessible | current | A 802.1p priority mapped to a traffic class priority queue. |
| 1.3.6.1.4.1.248.12.1.2.17.1.1.1 | Columnhm2AgentClassOfServicePortPriority | not-accessible | current | The Priority value determined for the received frame. This value is equivalent to the priority indicated in the tagged frame received, or one of the evaluated … |
| 1.3.6.1.4.1.248.12.1.2.17.1.1.2 | Columnhm2AgentClassOfServicePortClass | read-write | current | Traffic class priority queue the received frame is mapped to. |
| 1.3.6.1.4.1.248.12.1.2.31 | Tablehm2AgentKeepalivePortTable | not-accessible | current | Keepalive port table. |
| 1.3.6.1.4.1.248.12.1.2.31.1 | Rowhm2AgentKeepalivePortEntry | not-accessible | current | Keepalive port table. |
| 1.3.6.1.4.1.248.12.1.2.31.1.1 | Columnhm2AgentKeepalivePortState | read-write | current | The keepalive state for the port. enable(1) - enables keepalive on the port. disable(2) - disables keepalive on the port. The default port keepalive state is d… |
| 1.3.6.1.4.1.248.12.1.2.31.1.2 | Columnhm2AgentKeepalivePortLoopDetected | read-only | current | Keepalive status for the port. yes (1) - loop detected on the port. no (2) - no loop detected on the port. |
| 1.3.6.1.4.1.248.12.1.2.31.1.3 | Columnhm2AgentKeepalivePortLoopCount | read-only | current | The loop count on a specific port. |
| 1.3.6.1.4.1.248.12.1.2.31.1.5 | Columnhm2AgentKeepalivePortRxAction | read-write | current | Action on detecting a loop on the port. trap (10) - send a trap. auto-disable (11) - execute auto disable configured action. all (12) - all above mentioned act… |
| 1.3.6.1.4.1.248.12.1.2.31.1.7 | Columnhm2AgentKeepalivePortLastLoopDetectedTime | read-only | current | TimeStamp when last loop was detected on a port. |
| 1.3.6.1.4.1.248.12.1.2.31.1.8 | Columnhm2AgentKeepalivePortTpidType | read-write | current | Type of TPID to be used for loop protection or None if no vlan based loop protection is required. |
| 1.3.6.1.4.1.248.12.1.2.31.1.9 | Columnhm2AgentKeepalivePortVlanId | read-write | current | Vlan Id to be used for loop protection or None if no vlan based loop protection is required. |
| 1.3.6.1.4.1.248.12.1.2.31.1.248 | Columnhm2AgentKeepalivePortMode | read-write | current | The keepalive mode for the port. active(1) - enables transmission of keepalive check frames. passive(2) - disables transmission of check frames, only reception… |
| 1.3.6.1.4.1.248.12.1.2.31.1.249 | Columnhm2AgentKeepalivePortTxFrameCount | read-only | current | The amount of keepalive check frames sent on a specific port. |
| 1.3.6.1.4.1.248.12.1.2.31.1.250 | Columnhm2AgentKeepalivePortRxFrameCount | read-only | current | The amount of keepalive check frames received on a specific port. |
| 1.3.6.1.4.1.248.12.1.2.31.1.251 | Columnhm2AgentKeepalivePortDiscardFrameCount | read-only | current | The amount of keepalive check frames discarded on a specific port. |
| 1.3.6.1.4.1.248.12.1.2.31.1.252 | Columnhm2AgentKeepalivePortStatsClear | read-write | current | Clear keepalive statistics on a specific port. When read always returns 'other'. |
| 1.3.6.1.4.1.248.12.1.2.248 | Nodehm2AgentPortRedirectGroup | |||
| 1.3.6.1.4.1.248.12.1.2.248.1 | Tablehm2AgentPortRedirectTable | not-accessible | current | This table includes entries for each Redirect session. |
| 1.3.6.1.4.1.248.12.1.2.248.1.1 | Rowhm2AgentPortRedirectEntry | not-accessible | current | Provides configuration of a Redirect session specifying the destination port, and the source Port Mask, providing a many-to-one mapping. |
| 1.3.6.1.4.1.248.12.1.2.248.1.1.1 | Columnhm2AgentPortRedirectDestinationPort | not-accessible | current | The port which traffic from the redirected ports will be sent to. |
| 1.3.6.1.4.1.248.12.1.2.248.1.1.2 | Columnhm2AgentPortRedirectSourcePortMask | read-create | current | The ports from which traffic will be redirected to the destination port. The destination port can not be included in this list of ports. |
| 1.3.6.1.4.1.248.12.1.2.248.1.1.3 | Columnhm2AgentPortRedirectRowStatus | read-create | current | The status of this port mirroring session. |
| 1.3.6.1.4.1.248.12.1.3 | Nodehm2AgentSystemGroup | |||
| 1.3.6.1.4.1.248.12.1.3.9 | Scalarhm2AgentClearVlan | read-write | current | clear vlan entries |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| Hm2AgentPortMask | OCTET STRING | current | Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents… |
| Ipv6Address | OCTET STRING (SIZE (16)) | current | This data type is used to model IPv6 addresses. This is a binary string of 16 octets in network byte order. |
| Ipv6AddressIfIdentifier | OCTET STRING (SIZE (0..8)) | current | This data type is used to model IPv6 address interface identifiers. This is a binary string of up to 8 octets in network byte order. |
| Ipv6AddressPrefix | OCTET STRING (SIZE (0..16)) | current | This data type is used to model IPv6 address prefixes. This is a binary string of up to 16 octets in network byte order. |
| Ipv6IfIndex | Integer32 (1..2147483647) | current | A unique value, greater than zero for each internetwork layer interface in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each internetwork layer interface mus… |
| Ipv6IfIndexOrZero | Integer32 (0..2147483647) | current | This textual convention is an extension of the Ipv6IfIndex convention. The latter defines a greater than zero value used to identify an IPv6 interface in the managed system. This extension permits the additional value o… |
| LagList | OCTET STRING | current | Each octet within this value specifies a set of eight LAGs, with the first octet specifying LAG 1 through 8, the second octet specifying LAG 9 through 16, etc. Within each octet, the most significant bit represents LAG1… |
| VlanList | OCTET STRING | current | Each octet within this value specifies a set of eight vlans, with the first octet specifying vlans 1 through 8, the second octet specifying vlans 9 through 16, etc. Within each octet, the most significant bit represents… |