HP-ICF-RATE-LIMIT-MIB
127 objects
This MIB module describes HP rate limit information.
Imported Objects
| HP-ICF-OID | hpicfObjectModules hpicfRateLimitTrapsPrefix |
| IF-MIB | ifIndex InterfaceIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.11.2.14.10.2.14 | IdentityhpicfRateLimitMIB | This MIB module describes HP rate limit information. | ||
| 1.3.6.1.4.1.11.2.14.10.2.14.1 | NodehpicfRateLimitObjects | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.1.1 | NodehpicfICMPRateLimitObjects | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.1.1.1 | NodehpICMPRateLimitConfig | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1 | TablehpICMPRateLimitPortConfigTable | not-accessible | current | A table that contains configuration objects on ICMP rate limit on a per interface basis. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1 | RowhpICMPRateLimitPortConfigEntry | not-accessible | current | Entry that contains configuration objects on ICMP rate limit on a per interface basis |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.1 | ColumnhpICMPRateLimitPortConfigIndex | not-accessible | current | The interface index associated with this entry. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.2 | ColumnhpICMPRateLimitPortState | read-write | deprecated | This object indicates whether ICMP rate limiting is enabled on the corresponding port. Because this is a State object it cannot distinguish between percent-bas… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.3 | ColumnhpICMPRateLimitPortPrct | read-write | current | This indicates the percent of ICMP rate limit on the port. The value of this object must be interpreted under the context of hpICMPRateLimitPortState. A value … |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.4 | ColumnhpICMPRateLimitPortAlarmFlag | read-write | current | This object indicates whether ICMP rate limiting alarm has been sent. When an alarm is sent, this object is set to set(2). Once a management station changes th… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.5 | ColumnhpICMPRateLimitPortKbps | read-write | current | The maximum Kilobits-per-second of ICMP traffic that may be received inbound on the port. The value of this object must be interpreted under the context of hpI… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.6 | ColumnhpICMPRateLimitPortControlMode | read-write | current | The mode by which inbound ICMP traffic on this port will Rate-Limited. If icmpRateLimitPerPortOnly is configured, there will be a single maximum percentage-bas… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.7 | ColumnhpICMPRateLimitPortIpPacketType | read-write | current | This object represents the type(s) of IP packet to which the specified ICMP rate-limit will be applied. The default is IPv4. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.1.2 | ScalarhpICMPRateLimitNotifyPortIndex | accessible-for-notify | current | The interface index associated with hpICMPRateLimitPortNotification event. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.2 | NodehpicfBWMinEgressObjects | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.1.2.1 | NodehpBWMinEgressPortConfig | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.1.2.1.1 | ScalarhpBWMinEgressPortNumQueues | read-only | current | The number of bandwidth minimum egress queues supported on this system. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.2.1.2 | TablehpBWMinEgressPortPrctTable | not-accessible | current | A table that contains information about the port's egress Guaranteed Minimum Bandwidth percent configurations on this switch. The number of entries in this tab… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.2.1.2.1 | RowhpBWMinEgressPortPrctEntry | not-accessible | current | The information associated with each port's egress Guaranteed Minimum Bandwidth percent configuration. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.2.1.2.1.1 | ColumnhpBWMinEgressPortPrctQueue | not-accessible | current | The queue associated with this entry. The priority of the queues is in ascending order, starting with queue one being the lowest and queue hpBWMinEgressPortNum… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.2.1.2.1.2 | ColumnhpBWMinEgressPortPrct | read-write | current | The percentage of Guaranteed Minimum bandwidth to be assigned to this egress queue for this port. Total values for all queues must not exceed 100 percent. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.3 | NodehpicfBWMinIngressObjects | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.1.3.1 | NodehpBWMinIngressPortConfig | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.1.3.1.1 | ScalarhpBWMinIngressPortNumQueues | read-only | current | The number of bandwidth minimum ingress queues supported on this system. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.3.1.2 | TablehpBWMinIngressPortPrctTable | not-accessible | current | A table that contains information about the port's ingress Guaranteed Minimum Bandwidth percent configurations on this switch. The number of entries in this ta… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.3.1.2.1 | RowhpBWMinIngressPortPrctEntry | not-accessible | current | The information associated with each port's ingress Guaranteed Minimum Bandwidth percent configuration. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.3.1.2.1.1 | ColumnhpBWMinIngressPortPrctQueue | not-accessible | current | The queue associated with this entry. The priority of the queues is in ascending order, starting with queue one being the lowest and queue hpBWMinIngressPortNu… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.3.1.2.1.2 | ColumnhpBWMinIngressPortPrct | read-write | current | The percentage of Guaranteed Minimum bandwidth to be assigned to this ingress queue for this port. Total values for all queues must not exceed 100 percent. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4 | NodehpicfRateLimitPortObjects | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1 | NodehpRateLimitPortConfig | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.1 | ScalarhpEgressRateLimitPortNumQueues | read-only | current | The number of egress rate-limiting queues supported on this system. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2 | TablehpEgressRateLimitPortConfigTable | not-accessible | current | A table that contains information about the port egress Rate-Limiting configurations on this switch. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1 | RowhpEgressRateLimitPortConfigEntry | not-accessible | current | The information associated with each port's egress Rate-Limiting configuration. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1.1 | ColumnhpEgressRateLimitPortIndex | not-accessible | current | The ifIndex value which uniquely identifies a row in the Interfaces Table. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1.2 | ColumnhpEgressRateLimitPortControlMode | read-write | current | The mode by which this port will be Rate-Limited on egress. If egressRateLimitPerPortOnly is configured, there will be a single maximum percentage-based rate f… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1.3 | ColumnhpEgressRateLimitPortSingleControlPrct | read-write | current | When hpEgressRateLimitPortControlMode is configured for egressRateLimitPerPortOnly, this value is the maximum percentage of traffic that may be transmitted by … |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1.4 | ColumnhpEgressRateLimitPortSingleControlBps | read-write | deprecated | When hpEgressRateLimitPortControlMode is configured for egressRateLimitPerPortOnlyBpsMode, this value is the maximum bits-per-second of traffic that may be tra… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1.5 | ColumnhpEgressRateLimitPortSingleControlKbps | read-write | current | When hpEgressRateLimitPortControlMode is configured for egressRateLimitPerPortOnlyKbpsMode, this value is the maximum kilobits-per-second of traffic that may b… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1.6 | ColumnhpEgressRateLimitPortQueueControlMode | read-write | current | The mode by which queues on this port will be rate-limited on egress. If egressRateLimitQueuePrctMode is configured, the values for each of the queues indicate… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.3 | TablehpEgressRateLimitPortPrctTable | not-accessible | current | A table that contains information about the port egress Rate-Limiting percent configurations on this switch. The number of entries in this table is determined … |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.3.1 | RowhpEgressRateLimitPortPrctEntry | not-accessible | current | The information associated with each port's egress Rate-Limiting percent configuration. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.3.1.1 | ColumnhpEgressRateLimitPortPrctQueue | not-accessible | current | The queue associated with this entry. The priority o of the queues is in ascending order, starting with queue one being the lowest and queue hpEgressRateLimitg… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.3.1.2 | ColumnhpEgressRateLimitPortPrct | read-write | current | The maximum percentage of traffic that may be transmitted by this port's queue on egress. hpEgressRateLimitPortControlMode must be configured to use egressRate… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.4 | TablehpEgressRateLimitPortBpsTable | not-accessible | deprecated | A table that contains information about the port egress Rate-Limiting bits-per-second configurations on this switch. The number of entries in this table is det… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.4.1 | RowhpEgressRateLimitPortBpsEntry | not-accessible | deprecated | The information associated with each port's egress Rate-Limiting bits-per-second configuration. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.4.1.1 | ColumnhpEgressRateLimitPortBpsQueue | not-accessible | deprecated | The queue associated with this entry. The priority of the queues is in ascending order, starting with queue one being the lowest and queue hpEgressRateLimitgre… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.4.1.2 | ColumnhpEgressRateLimitPortBps | read-write | deprecated | The maximum bits-per-second of traffic that may be transmitted by this port's queue on egress. hpEgressRateLimitPortControlMode must be configured to use egres… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.5 | TablehpEgressRateLimitPortQueueConfigTable | not-accessible | current | A table that contains information about the port egress- queue rate-limiting configurations on this switch. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.5.1 | RowhpEgressRateLimitPortQueueConfigEntry | not-accessible | current | The information associated with the egress rate-limiting configuration for the queues on each port. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.5.1.1 | ColumnhpEgressRateLimitPortQueueIndex | not-accessible | current | The queue associated with this entry. The priority of the queues is in ascending order, starting with queue one being the lowest and queue hpEgressRateLimitEgr… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.5.1.2 | ColumnhpEgressRateLimitPortQueueMax | read-write | current | The maximum amount of traffic that may be transmitted by this port's corresponding queue on egress. When the value of hpEgressRateLimitPortQueueControlMode is … |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.5 | NodehpicfIngressRateLimitPortObjects | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.1.5.1 | NodehpRateLimitIngressPortConfig | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.1 | ScalarhpIngressRateLimitPortNumQueues | read-only | current | The number of ingress rate-limiting queues supported on this system. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2 | TablehpIngressRateLimitPortConfigTable | not-accessible | current | A table that contains information about the port ingress Rate-Limiting configurations on this switch. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2.1 | RowhpIngressRateLimitPortConfigEntry | not-accessible | current | The information associated with each port's ingress Rate-Limiting configuration. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2.1.1 | ColumnhpIngressRateLimitPortIndex | not-accessible | current | The ifIndex value which uniquely identifies a row in the Interfaces Table. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2.1.2 | ColumnhpIngressRateLimitPortControlMode | read-write | current | The mode by which this port will be Rate-Limited on ingress. If ingressRateLimitPerPortOnly is configured, there will be a single maximum percentage-based rate… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2.1.3 | ColumnhpIngressRateLimitPortSingleControlPrct | read-write | current | When hpIngressRateLimitPortControlMode is configured for ingressRateLimitPerPortOnly, this value is the maximum percentage of traffic that may be transmitted b… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2.1.4 | ColumnhpIngressRateLimitPortSingleControlBps | read-write | deprecated | When hpIngressRateLimitPortControlMode is configured for ingressRateLimitPerPortOnlyBpsMode, this value is the maximum bits-per-second of traffic that may be t… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2.1.5 | ColumnhpIngressRateLimitPortSingleControlKbps | read-write | current | When hpIngressRateLimitPortControlMode is configured for ingressRateLimitPerPortOnlyKbpsMode, this value is the maximum kilobits-per-second of traffic that may… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.3 | TablehpIngressRateLimitPortPrctTable | not-accessible | current | A table that contains information about the port ingress Rate-Limiting percent configurations on this switch. The number of entries in this table is determined… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.3.1 | RowhpIngressRateLimitPortPrctEntry | not-accessible | current | The information associated with each port's ingress Rate-Limiting percent configuration. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.3.1.1 | ColumnhpIngressRateLimitPortPrctQueue | not-accessible | current | The queue associated with this entry. The priority of the queues is in ascending order, starting with queue one being the lowest and queue hpIngressRateLimitgr… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.3.1.2 | ColumnhpIngressRateLimitPortPrct | read-write | current | The maximum percentage of traffic that may be transmitted by this port's queue on ingress. hpIngressRateLimitPortControlMode must be configured to use ingressR… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.4 | TablehpIngressRateLimitPortBpsTable | not-accessible | deprecated | A table that contains information about the port ingress Rate-Limiting bits-per-second configurations on this switch. The number of entries in this table is de… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.4.1 | RowhpIngressRateLimitPortBpsEntry | not-accessible | deprecated | The information associated with each port's egress Rate-Limiting bits-per-second configuration. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.4.1.1 | ColumnhpIngressRateLimitPortBpsQueue | not-accessible | deprecated | The queue associated with this entry. The priority of the queues is in ascending order, starting with queue one being the lowest and queue hpIngressRateLimitgr… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.4.1.2 | ColumnhpIngressRateLimitPortBps | read-write | deprecated | The maximum bits-per-second of traffic that may be transmitted by this port's queue on ingress. hpIngressRateLimitPortControlMode must be configured to use ing… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.6 | NodehpicfIngressBcastLimitPortObjects | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.1.6.1 | NodehpBcastLimitIngressPortConfig | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.1.6.1.1 | TablehpIngressBcastLimitPortConfigTable | not-accessible | current | A table that contains information about the port ingress Broadcast-Limiting configurations on this switch. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.6.1.1.1 | RowhpIngressBcastLimitPortConfigEntry | not-accessible | current | The information associated with each port's ingress Broadcast-Limiting configuration. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.6.1.1.1.1 | ColumnhpIngressBcastLimitPortIndex | not-accessible | current | The ifIndex value which uniquely identifies a row in the Interfaces Table. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.6.1.1.1.2 | ColumnhpIngressBcastLimitPortControlMode | read-write | current | The mode by which this port will be Broadcast-Limited on ingress. If ingressBcastLimitPerPortOnly is configured, there will be a single maximum percentage-base… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.6.1.1.1.3 | ColumnhpIngressBcastLimitPortSingleControlPrct | read-write | current | When hpIngressBcastLimitPortControlMode is configured for ingressBcastLimitPerPortOnly, this value is the maximum percentage of traffic that may be transmitted… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.6.1.1.1.4 | ColumnhpIngressBcastLimitPortSingleControlKbps | read-write | current | When hpIngressBcastLimitPortControlMode is configured for ingressBcastLimitPerPortOnlyKbpsMode, this value is the maximum kilobits-per-second of broadcast traf… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.7 | NodehpicfIngressMcastLimitPortObjects | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.1.7.1 | NodehpMcastLimitIngressPortConfig | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.1.7.1.1 | TablehpIngressMcastLimitPortConfigTable | not-accessible | current | A table that contains information about the port ingress Multicast-Limiting configurations on this switch. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.7.1.1.1 | RowhpIngressMcastLimitPortConfigEntry | not-accessible | current | The information associated with each port's ingress Multicast-Limiting configuration. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.7.1.1.1.1 | ColumnhpIngressMcastLimitPortIndex | not-accessible | current | The ifIndex value which uniquely identifies a row in the Interfaces Table. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.7.1.1.1.2 | ColumnhpIngressMcastLimitPortControlMode | read-write | current | The mode by which this port will be Multicast-Limited on ingress. If ingressMcastLimitPerPortOnly is configured, there will be a single maximum percentage-base… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.7.1.1.1.3 | ColumnhpIngressMcastLimitPortSingleControlPrct | read-write | current | When hpIngressMcastLimitPortControlMode is configured for ingressMcastLimitPerPortOnly, this value is the maximum percentage of multicast traffic that may be t… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.7.1.1.1.4 | ColumnhpIngressMcastLimitPortSingleControlKbps | read-write | current | When hpIngressMcastLimitPortControlMode is configured for ingressMcastLimitPerPortOnlyKbpsMode, this value is the maximum kilobits-per-second of multicast traf… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.8 | NodehpicfUnknownUnicastLimitPortObjects | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.1.8.1 | NodehpUnknownUnicastLimitPortConfig | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.1.8.1.1 | TablehpUnknownUnicastLimitConfigTable | not-accessible | current | A table that contains information about the unknown-unicast rate limiting configurations on this switch. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.8.1.1.1 | RowhpUnknownUnicastLimitConfigEntry | not-accessible | current | The information associated with each port's unknown-unicast rate limiting configuration. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.8.1.1.1.1 | ColumnhpUnknownUnicastLimitPortIndex | not-accessible | current | The ifIndex value which uniquely identifies a row in the interfaces table. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.8.1.1.1.2 | ColumnhpUnknownUnicastLimitPortControlMode | read-write | current | The mode by which unknown-unicast ingress traffic on this port will be rate limited. If unknownUnicastLimitPerPortOnly is configured, the limit will be a perce… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.8.1.1.1.3 | ColumnhpUnknownUnicastLimitPortSingleControlPrct | read-write | current | When hpUnknownUnicastLimitPortControlMode is unknownUnicastLimitPerPortOnly, this value is the maximum allowed ingress rate for unknown-unicast traffic on this… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.8.1.1.1.4 | ColumnhpUnknownUnicastLimitPortSingleControlKbps | read-write | current | When hpUnknownUnicastLimitPortControlMode is UnknownUnicastLimitPerPortOnlyKbpsMode, this value is the maximum allowed ingress rate for unknown-unicast traffic… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.9 | NodehpicfIngressRateLimitVlanObjects | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.1.9.1 | TablehpicfIngressRateLimitVlanConfigTable | not-accessible | current | A table of VLAN rate limits. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.9.1.1 | RowhpicfIngressRateLimitVlanConfigEntry | not-accessible | current | A set of objects used to configure rate limits on a VLANs. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.9.1.1.1 | ColumnhpicfIngressRateLimitVlanIndex | not-accessible | current | The VLAN ifIndex value that uniquely identifies a row in the Interfaces Table and corresponds to the VLAN on which the rate limit is being set. |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.9.1.1.2 | ColumnhpicfIngressRateLimitVlanControlMode | read-write | current | The rate limit mode. A value of 1 indicates that there is no rate limit set. A value of 2 indicates that the rate limit on the VLAN will be set in Kilobits per… |
| 1.3.6.1.4.1.11.2.14.10.2.14.1.9.1.1.3 | ColumnhpicfIngressRateLimitVlanKbps | read-write | current | The maximum rate of inbound traffic permitted on the VLAN in kilobits per second. This limit is the total aggregate inbound traffic allowed across all ports in… |
| 1.3.6.1.4.1.11.2.14.10.2.14.2 | NodehpicfRateLimitConformance | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1 | NodehpicfRateLimitGroups | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1.1 | GrouphpICMPRateLimitPortConfigGroup | deprecated | A collection of objects providing configuration to ICMP rate limiting on an interface. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1.2 | GrouphpICMPRateLimitPortNotifyGroup | current | A collection of notifications used to indicate ICMP rate limiting on an interface events. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1.3 | GrouphpBWMinIngressPortConfigGroup | current | A collection of objects providing configuration to Guaranteed Minimum ingress bandwidth on an interface. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1.4 | GrouphpBWMinEgressPortConfigGroup | current | A collection of objects providing configuration to Guaranteed Minimum egress bandwidth on an interface. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1.5 | GrouphpEgressRateLimitPortConfigGroup | deprecated | A collection of objects providing configuration to Egress Rate-Limiting on an interface. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1.6 | GrouphpIngressRateLimitPortConfigGroup | deprecated | A collection of objects providing configuration to Ingress Rate-Limiting on an interface. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1.7 | GrouphpICMPRateLimitPortConfigGroup2 | deprecated | This replaces the deprecated hpICMPRateLimitPortConfigGroup. A collection of objects providing configuration to ICMP rate limiting on an interface. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1.8 | GrouphpEgressRateLimitPortConfigGroup2 | deprecated | This replaces the deprecated hpEgressRateLimitPortConfigGroup. A collection of objects providing configuration to Egress Rate-Limiting on an interface. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1.9 | GrouphpIngressRateLimitPortConfigGroup2 | current | This replaces the deprecated hpIngressRateLimitPortConfigGroup. A collection of objects providing configuration to Ingress Rate-Limiting on an interface. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1.10 | GrouphpBcastLimitIngressPortConfigGroup | deprecated | A collection of objects providing configuration to Ingress Broadcast Limiting on an interface. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1.11 | GrouphpMcastLimitIngressPortConfigGroup | current | A collection of objects providing configuration to Ingress Multicast Limiting on an interface. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1.12 | GrouphpBcastLimitIngressPortConfigGroup2 | current | This replaces the deprecated hpBcastLimitIngressPortConfigGroup. A collection of objects providing configuration of Ingress Broadcast Limiting on an interface. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1.13 | GrouphpMcastLimitIngressPortConfigGroup2 | current | This replaces the deprecated hpMcastLimitIngressPortConfigGroup A collection of objects providing configuration of Ingress Multicast Limiting on an interface. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1.14 | GrouphpICMPRateLimitPortConfigGroup3 | current | This replaces the deprecated hpICMPRateLimitPortConfigGroup2. A collection of objects providing configuration for ICMP rate limiting on an interface. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1.15 | GrouphpUnknownUcastLimitIngressPortConfigGroup | deprecated | A collection of objects providing configuration to Ingress Unknown Unicast traffic Limiting on an interface. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1.16 | GrouphpicfIngressRateLimitVlanGroup | current | A collection of HP proprietary objects to support configuration of VLAN-based rate limits on HP Networking devices. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1.17 | GrouphpUnknownUcastLimitIngressPortConfigGroup2 | current | A collection of objects providing configuration to Ingress Unknown Unicast traffic Limiting on an interface. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1.18 | GrouphpEgressRateLimitPortConfigGroup3 | current | This replaces the deprecated hpEgressRateLimitPortConfigGroup2. A collection of objects providing configuration to Egress Rate-Limiting on an interface. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.1.19 | GrouphpEgressRateLimitPortQueueConfigEntryGroup | current | A collection of objects providing configuration to egress rate-limit on an interface queues. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.2 | NodehpicfRateLimitCompliances | |||
| 1.3.6.1.4.1.11.2.14.10.2.14.2.2.1 | CompliancehpicfRateLimitCompliance | deprecated | The compliance statement for device support of HP-ICF-RATE-LIMIT MIB. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.2.2 | CompliancehpicfRateLimitCompliance1 | deprecated | The compliance statement for device support of HP-ICF-RATE-LIMIT MIB. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.2.3 | CompliancehpicfRateLimitCompliance2 | not-accessible | deprecated | The compliance statement for device support of HP-ICF-RATE-LIMIT MIB. |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.2.4 | CompliancehpicfRateLimitCompliance3 | current | The compliance statement for HP switches running IngressRateLimitVlan feature. | |
| 1.3.6.1.4.1.11.2.14.10.2.14.2.2.5 | CompliancehpicfRateLimitCompliance4 | not-accessible | current | The compliance statement for device support of HP-ICF-RATE-LIMIT MIB. |
| 1.3.6.1.4.1.11.2.14.12.5.0.1 | NotificationhpICMPRateLimitPortNotification | current | This notification indicates limit has exceeded. |