HP-PROCURVE-420-PRIVATE-MIB
100 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC1155-SMI | Counter enterprises IpAddress mgmt |
| RFC1213-MIB | ifIndex |
| SNMPv2-SMI | -- Integer32 Counter32 |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.11 | NodehP | |||
| 1.3.6.1.4.1.11.2 | Nodewireless | |||
| 1.3.6.1.4.1.11.2.3 | Nodeenterprise | |||
| 1.3.6.1.4.1.11.2.3.7 | NodeaccessPoint | |||
| 1.3.6.1.4.1.11.2.3.7.11 | NodeproCurve | |||
| 1.3.6.1.4.1.11.2.3.7.11.37 | NodehPProCuve420 | |||
| 1.3.6.1.4.1.11.2.3.7.11.37.1 | NodeenterpriseApSys | |||
| 1.3.6.1.4.1.11.2.3.7.11.37.1.1 | ScalarswHardwareVer | read-only | mandatory | Hardware version of the main board. |
| 1.3.6.1.4.1.11.2.3.7.11.37.1.2 | ScalarswBootRomVer | read-only | mandatory | Boot ROM code version of the main board. |
| 1.3.6.1.4.1.11.2.3.7.11.37.1.3 | ScalarswOpCodeVer | read-only | mandatory | Operation code version of the main board. |
| 1.3.6.1.4.1.11.2.3.7.11.37.1.4 | ScalarswCountryCode | read-write | mandatory | Country code of the AP. AL-ALBANIA, DZ-ALGERIA, AR-ARGENTINA, AM-ARMENIA, AU-AUSTRALIA, AT-AUSTRIA, AZ-AZERBAIJAN, BH-BAHRAIN, BY-BELARUS, BE-BELGIUM, BZ-BELIZ… |
| 1.3.6.1.4.1.11.2.3.7.11.37.2 | NodeenterpriseApLineMgnt | |||
| 1.3.6.1.4.1.11.2.3.7.11.37.2.1 | TablelineTable | not-accessible | mandatory | Table of descriptive and status information about configuration of each RS-232 line in this system |
| 1.3.6.1.4.1.11.2.3.7.11.37.2.1.1 | RowlineEntry | not-accessible | mandatory | An entry in the table, containing information about configuration in one RS232 line of the Access Point. |
| 1.3.6.1.4.1.11.2.3.7.11.37.2.1.1.1 | ColumnlineIndex | not-accessible | mandatory | This is defined as RS-232 index. |
| 1.3.6.1.4.1.11.2.3.7.11.37.2.1.1.2 | ColumnlineDataBits | read-only | mandatory | This is defined as number of data bits for the RS232 interface. |
| 1.3.6.1.4.1.11.2.3.7.11.37.2.1.1.3 | ColumnlineParity | read-only | mandatory | This is defined as parity of the RS232 interface. |
| 1.3.6.1.4.1.11.2.3.7.11.37.2.1.1.4 | ColumnlineSpeed | read-only | mandatory | This is defined as the speed of the RS-232 interface. |
| 1.3.6.1.4.1.11.2.3.7.11.37.2.1.1.5 | ColumnlineStopBits | read-only | mandatory | This is defined as the number of stop bits for the RS-232 interface. |
| 1.3.6.1.4.1.11.2.3.7.11.37.3 | NodeenterpriseApPortMgnt | |||
| 1.3.6.1.4.1.11.2.3.7.11.37.3.1 | TableportTable | not-accessible | mandatory | Table of descriptive and status information about configuration of each switch port (including expansion slot) in this system. This table also contains informa… |
| 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1 | RowportEntry | not-accessible | mandatory | An entry in the table, containing information about configuration in one switch port of the switch. |
| 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.1 | ColumnportIndex | not-accessible | mandatory | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.2 | ColumnportName | read-only | mandatory | Indicates the port name. This is same as ifAlias in the IF-MIB (RFC2863 or later). |
| 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.3 | ColumnportType | read-only | mandatory | Indicates the port type. |
| 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.4 | ColumnportSpeedDpxCfg | read-only | mandatory | Set the port speed and duplex mode as follows: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 1… |
| 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.5 | ColumnportFlowCtrlCfg | read-only | mandatory | (1) Flow control mechanism is enabled. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPr… |
| 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.6 | ColumnportCapabilities | read-only | mandatory | Port capabilities. |
| 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.7 | ColumnportAutonegotiation | read-only | mandatory | Whether autonegotiation is enabled. |
| 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.8 | ColumnportSpeedDpxStatus | read-only | mandatory | The operating speed and duplex mode of the switched port. If this index is a trunk, the speed is the speed of its individual members. If this index is a trunk … |
| 1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.9 | ColumnportFlowCtrlStatus | read-only | mandatory | (2) BackPressure flow control machanism is used. (3) IEEE 802.3 flow control machanism is used. (4) Flow control mechanism is disabled. If this index is a trun… |
| 1.3.6.1.4.1.11.2.3.7.11.37.4 | NodeenterpriseApFileTransferMgt | |||
| 1.3.6.1.4.1.11.2.3.7.11.37.4.1 | ScalartransferStart | read-write | mandatory | Set to go(1) to start a transfer. |
| 1.3.6.1.4.1.11.2.3.7.11.37.4.2 | ScalartransferType | read-write | mandatory | Type of file to transfer. |
| 1.3.6.1.4.1.11.2.3.7.11.37.4.3 | ScalarfileType | read-write | mandatory | Type of file to transfer. |
| 1.3.6.1.4.1.11.2.3.7.11.37.4.4 | ScalarsrcFile | read-write | mandatory | The source file name for TFTP transfer when a transfer is next requested via this MIB. This value is set to the zero length string when no file name has been s… |
| 1.3.6.1.4.1.11.2.3.7.11.37.4.5 | ScalardestFile | read-write | mandatory | The destination file name for TFTP transfer when a transfer is next requested via this MIB. This value is set to the zero length string when no file name has b… |
| 1.3.6.1.4.1.11.2.3.7.11.37.4.6 | ScalarfileServer | read-write | mandatory | The IP address of the TFTP server for transfer when a download is next requested via this MIB. This value is set to `0.0.0.0' when no IP address has been speci… |
| 1.3.6.1.4.1.11.2.3.7.11.37.4.7 | ScalaruserName | read-write | mandatory | The username specified for an FTP Transfer. |
| 1.3.6.1.4.1.11.2.3.7.11.37.4.8 | Scalarpassword | read-write | mandatory | The password specified for an FTP Transfer. |
| 1.3.6.1.4.1.11.2.3.7.11.37.5 | NodeenterpriseApResetMgt | |||
| 1.3.6.1.4.1.11.2.3.7.11.37.5.1 | ScalarrestartOpCodeFile | read-write | mandatory | Name of op-code file for start-up. |
| 1.3.6.1.4.1.11.2.3.7.11.37.5.2 | ScalarrestartControl | read-write | mandatory | Setting this object to warmBoot(2) causes the device to restart the application software with current configuration parameters saved in non-volatile memory. Se… |
| 1.3.6.1.4.1.11.2.3.7.11.37.6 | NodeenterpriseApIpMgt | |||
| 1.3.6.1.4.1.11.2.3.7.11.37.6.1 | ScalarnetConfigIPAddress | read-write | mandatory | The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then w… |
| 1.3.6.1.4.1.11.2.3.7.11.37.6.2 | ScalarnetConfigSubnetMask | read-write | mandatory | The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then … |
| 1.3.6.1.4.1.11.2.3.7.11.37.6.3 | ScalarnetDefaultGateway | read-write | mandatory | The IP Address of the default gateway. If this value is undefined or unknown, it shall have the value 0.0.0.0. |
| 1.3.6.1.4.1.11.2.3.7.11.37.6.4 | ScalaripHttpState | read-write | mandatory | Whether HTTP is enabled. |
| 1.3.6.1.4.1.11.2.3.7.11.37.6.5 | ScalaripHttpPort | read-write | mandatory | The port number for HTTP. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7 | NodeenterpriseAPdot11 | |||
| 1.3.6.1.4.1.11.2.3.7.11.37.7.1 | Tablehpdot11StationConfigTable | not-accessible | mandatory | Table of descriptive and status information about configuration of each radio of the AP. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.1.1 | Rowhpdot11StationConfigEntry | not-accessible | mandatory | An entry in the table, containing information about configuration in one radio of the AP. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.1.1.1 | Columnhpdot11portIndex | not-accessible | mandatory | Radio index of the AP. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.1.1.2 | Columnhpdot11DesiredSSID | read-write | mandatory | This attribute reflects the Service Set ID used in the DesiredSSID parameter of the most recent MLME_Scan.request. This value may be modified by an external ma… |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.1.1.3 | Columnhpdot11BeaconPeriod | read-write | mandatory | This attribute shall specify the number of ms that a station shall use for scheduling Beacon transmissions. This value is transmitted in Beacon and Probe Respo… |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.1.1.4 | Columnhpdot11DTIMPeriod | read-write | mandatory | This attribute shall specify the number of beacon intervals that shall elapse between transmission of Beacons frames containing a TIM element whose DTIM Count … |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.1.1.5 | Columnhpdot11OperationalRateSet | read-write | mandatory | This attribute shall specify the set of data rates at which the station may transmit data. Each octet contains a value representing a rate. Each rate shall be … |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.1.1.6 | Columnhpdot11AuthenticationAlgorithm | read-write | mandatory | This attribute shall be a set of all the authentication algorithms supported by the STAs. The following are the default values and the associated algorithm. Va… |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.2 | Tablehpdot11PrivacyTable | not-accessible | mandatory | Table of descriptive and status information about configuration of each radio of the AP. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.2.1 | Rowhpdot11PrivacyEntry | not-accessible | mandatory | An entry in the table, containing information about configuration in one radio of the AP. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.2.1.1 | Columnhpdot11PrivacyportIndex | not-accessible | mandatory | Radio index of the AP. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.2.1.2 | Columnhpdot11PrivacyInvoked | read-write | mandatory | When this attribute is true, it shall indicate that the IEEE 802.11 WEP mechanism is used for transmitting frames of type Data. The default value of this attri… |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.2.1.3 | Columnhpdot11WEPDefaultKeyID | read-write | mandatory | This attribute shall indicate the use of the first, second, or third element of the WEPDefaultKeys array when set to values of zero, one, or two(the fourth are… |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.2.1.4 | Columnhpdot11WEPKeyMappingLength | read-write | mandatory | The maximum number of tuples that dot11WEPKeyMappings can hold. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.3 | Nodehpdot11mac | |||
| 1.3.6.1.4.1.11.2.3.7.11.37.7.3.1 | Tablehpdot11OperationTable | not-accessible | mandatory | Table of descriptive and status information about configuration of each radio of the AP. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.3.1.1 | Rowhpdot11OperationEntry | not-accessible | mandatory | An entry in the table, containing information about configuration in one radio of the AP. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.3.1.1.1 | Columnhpdot11OperationIndex | not-accessible | mandatory | Radio index of the AP. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.3.1.1.2 | Columnhpdot11RTSThreshold | read-write | mandatory | This attribute shall indicate the number of octets in an MPDU, below which an RTS/CTS handshake shall not be performed. An RTS/CTS handshake shall be performed… |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.3.1.1.3 | Columnhpdot11FragmentationThreshold | read-write | mandatory | This attribute shall specify the mandatory maximum size, in octets, of the MPDU that may be delivered to the PHY. An MSDU shall be broken into fragments if its… |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.4 | Nodehpdot11phy | |||
| 1.3.6.1.4.1.11.2.3.7.11.37.7.4.1 | Tablehpdot11PhyOperationTable | not-accessible | mandatory | Table of descriptive and status information about configuration of each radio of the AP. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.4.1.1 | Rowhpdot11PhyOperationEntry | not-accessible | mandatory | An entry in the table, containing information about configuration in one radio of the AP. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.4.1.1.1 | Columnhpdot11Index | not-accessible | mandatory | Radio index of the AP. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.4.1.1.2 | Columnhpdot11CurrentChannel | read-write | mandatory | The current operating frequency channel of the network |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.4.1.1.3 | Columnhpdot11TurboModeEnabled | read-only | mandatory | This attribute, when true, shall indicate that the propietory turbo mode option is enabled. The default value of this attribute shall be false. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.4.1.1.4 | Columnhpdot11PreambleLength | read-write | mandatory | This attribute determines whether or not a short or a long preamble is used to delineate 802.11 frames. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.5 | Nodehpdot11AuthenticationEntry | |||
| 1.3.6.1.4.1.11.2.3.7.11.37.7.5.1 | Scalarhpdot118021xSupport | read-write | mandatory | This attribute, when true(1), indicates that the Enterprise Access Point supports the 802.1x authentication algorithm. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.5.2 | Scalarhpdot118021xRequired | read-write | mandatory | This attribute, when true(1), indicates that the Enterprise Access Point requires successful 802.1x authentication for any clients accessing the network. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.6 | Tablehpdot11AuthenticationServerTable | not-accessible | mandatory | Table of descriptive and status information about configuration of each authentication server. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.6.1 | Rowhpdot11AuthenticationServerEntry | not-accessible | mandatory | An entry in the table, containing information about configuration in one radio of the AP. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.6.1.1 | Columnhpdot11serverIndex | not-accessible | mandatory | Radio index of the AP. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.6.1.2 | Columnhpdot11AuthenticationServer | read-write | mandatory | This values indicates the IP address of the authentication server. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.6.1.3 | Columnhpdot11AuthenticationPort | read-write | mandatory | This values indicates the UDP Port used by the primary authentication server. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.6.1.4 | Columnhpdot11AuthenticationKey | read-write | mandatory | This values indicates the shared key used by the authentication server. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.6.1.5 | Columnhpdot11AuthenticationRetransmit | read-write | mandatory | This values indicates the retransmit timer length used by the authentication server. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.6.1.6 | Columnhpdot11AuthenticationTimeout | read-write | mandatory | This values indicates the Timeout value(sec) used by the authentication server. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.7 | Tablehpdot11FilterTable | not-accessible | mandatory | Table of status information about each configured MAC Address Filtering Entry. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.7.1 | Rowhpdot11FilterEntry | not-accessible | mandatory | An entry in the table, containing information about configuration in one radio of the AP. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.7.1.1 | Columnhpdot11FilterIndex | not-accessible | mandatory | Filter index. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.7.1.2 | Columnhpdot11FilterAddress | read-write | mandatory | This values indicates the MAC address of the filter entry. |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.7.1.3 | Columnhpdot11FilterStatus | read-write | mandatory | This values indicates the Status of the filter entry. Ifallowed, the client is allowed access to the network. If disallowed, the no frames will be forwarded to… |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.8 | Nodehpdot11smt | |||
| 1.3.6.1.4.1.11.2.3.7.11.37.7.8.1 | Nodehpdot11WEPDefaultKeys11g | |||
| 1.3.6.1.4.1.11.2.3.7.11.37.7.8.1.1 | Tablehpdot11WEPDefaultKeys11gTable | not-accessible | mandatory | Conceptual table for WEP default keys. This table shall contain the four WEP default secret key values corresponding to the four possible KeyID values. The WEP… |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.8.1.1.1 | Rowhpdot11WEPDefaultKeys11gEntry | not-accessible | mandatory | An Entry (conceptual row) in the WEP Default Keys Table. ifIndex - Each 802.11 interface is represented by an ifEntry. Interface tables in this MIB module are … |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.8.1.1.1.1 | Columnhpdot11WEPDefaultKey11gLength | read-write | mandatory | A 40(64)-bits [5 octets WEP], 104(128)-bits [13 octets] or 128(152)-bits [16 octets] |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.8.1.1.1.2 | Columnhpdot11WEPDefaultKey11gIndex | not-accessible | mandatory | The auxiliary variable used to identify instances of the columnar objects in the WEP Default Keys Table. The value of this variable is equal to the WEPDefaultK… |
| 1.3.6.1.4.1.11.2.3.7.11.37.7.8.1.1.1.3 | Columnhpdot11WEPDefaultKey11gValue | read-write | mandatory | A 40(64)-bits [5 octets WEP] or 104(128)-bits [13 octets] default secret key value. |