HP-SN-SWITCH-GROUP-MIB
319 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1 | NodesnSwInfo | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.1 | ScalarsnSwGroupOperMode | read-write | mandatory | noVLan(1) represents all switch ports with no virtual LAN by port (no Port VLAN), and with no tag assigned. vlanByPort(2) represents all switch ports with Basi… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.2 | ScalarsnSwGroupIpL3SwMode | read-write | mandatory | The Switch Group is configured with the Layer3 IP Switch mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate Layer3… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.3 | ScalarsnSwGroupIpMcastMode | read-write | mandatory | The Switch Group is configured with the IP Multicast pruning mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate IP… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.4 | ScalarsnSwGroupDefaultCfgMode | read-write | mandatory | The Switch Group is configured with the Default configuration. If the default configuration gets overwritten, the state will change to non-default. default(1).… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.5 | ScalarsnSwGroupSwitchAgeTime | read-write | mandatory | The Switch Age time is 180sec by default. The configured range is 10 to 10,000sec. The time represents the time span to age out an MAC Address entry. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.6 | ScalarsnVLanGroupVlanCurEntry | read-only | mandatory | The current total entry number of VLANs are configured. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.7 | ScalarsnVLanGroupSetAllVLan | read-write | mandatory | The value of this object is the VLanIndex of a particalur entry in snVLanByPortTable (snVLanByPortVLanIndex). All the attributes of that row of table except Po… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.8 | ScalarsnSwPortSetAll | read-write | mandatory | The value of this object is the index number of the snSwPortInfoTable (snSwPortInfoPortIndex). snSwPortInfoMonitorMode, snSwPortInfoTagType, snSwPortInfoChnMod… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.9 | ScalarsnFdbTableCurEntry | read-only | mandatory | The current total entry number of FDB are configured. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.10 | ScalarsnFdbTableStationFlush | read-write | mandatory | The following values of the flush state can only be read: normal(1)... normal state error(2)... operation failed flushing(4)... in process The following value … |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.11 | ScalarsnPortStpSetAll | read-write | mandatory | The value of this object is 1 which means invoking Port STP Set-all command. The snPortStpPriority, snPortStpPathCost, the read-write STP related attributes of… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.12 | ScalarsnSwProbePortNum | read-write | mandatory | A chassis switch probe port is operated as a traffic analyzer port and only one port can be assigned in the chassis. The bit 0 to bit 7: port number. The bit 8… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.13 | ScalarsnSw8021qTagMode | read-write | mandatory | The Switch Group is configured with the IEEE802.1q Tagging mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate IEEE… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.14 | ScalarsnSwGlobalStpMode | read-write | mandatory | Spanning Tree System Global Mode in the Switch Group can be set either enabled or disabled and the default is enabled mode. enabled(1)...........activate Spann… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.15 | ScalarsnSwIpMcastQuerierMode | read-write | mandatory | The IP Multicast pruning mode is configured either Non-Querier or Querier mode and the default is querier mode. querier(1)...........when prunning traffic loca… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.17 | ScalarsnSwViolatorPortNumber | read-only | mandatory | The port number of the switch or router that received a violator packet. It is included in the locked address violation trap. The bit 0 to bit 7: port number. … |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.18 | ScalarsnSwViolatorMacAddress | read-only | mandatory | The source address of the violator packet received by the switch or router. It is included in the locked address violation trap. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.19 | ScalarsnVLanGroupVlanMaxEntry | read-write | mandatory | The maximum number of VLAN entries are allowed to configure. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.20 | ScalarsnSwEosBufferSize | read-only | mandatory | A specific buffer size for all the different EOS buffers. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.21 | ScalarsnVLanByPortEntrySize | read-only | mandatory | The size of each VLAN table entry. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.22 | ScalarsnSwPortEntrySize | read-only | mandatory | The size of each port table entry. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.23 | ScalarsnFdbStationEntrySize | read-only | mandatory | The size of each Fdb station table entry. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.24 | ScalarsnPortStpEntrySize | read-only | mandatory | The size of each port stp table entry. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.25 | ScalarsnSwEnableBridgeNewRootTrap | read-write | mandatory | Indicates whether the SNMP agent process is permitted to generate bridge new root traps. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.26 | ScalarsnSwEnableBridgeTopoChangeTrap | read-write | mandatory | Indicates whether the SNMP agent process is permitted to generate bridge topology change traps. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.27 | ScalarsnSwEnableLockedAddrViolationTrap | read-write | mandatory | Indicates whether the SNMP agent process is permitted to generate locked address violation traps. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.28 | ScalarsnSwIpxL3SwMode | read-write | mandatory | The Switch Group is configured with the Layer3 IPX Switch mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate Layer… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.29 | ScalarsnVLanByIpSubnetMaxSubnets | read-only | mandatory | The maximum number of subnets for each IP VLAN. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.30 | ScalarsnVLanByIpxNetMaxNetworks | read-only | mandatory | The maximum number of networks for each IPX VLAN. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.31 | ScalarsnSwProtocolVLanMode | read-write | mandatory | disabled(0) - represents system with Protocol VLAN disabled. enabled(1) - represents system with Protocol VLAN enabled (Layer3 VLAN). |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.32 | ScalarsnMacStationVLanId | read-write | mandatory | This MAC Station VLAN ID index to the standard Forwarding Database for Transparent Bridge Table. (dot1dTpFdbTable). Since the dot1dTpFdbTable index is the MAC … |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.33 | ScalarsnSwClearCounters | read-write | mandatory | valid(0) - a SNMP-GET of this mib shows that it is valid command to use. clear(1) - represents clear counter command of the following counters: Dot3, MIB2, IP … |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.34 | ScalarsnSw8021qTagType | read-write | mandatory | The IEEE802.1q tag type embedded in the length/type field of an Ethernet packet. It specifies that the 2 octets after the length/type field in an Ethernet pack… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.35 | ScalarsnSwBroadcastLimit | read-write | mandatory | Limit the number of broadcast packets to forward out of the switch ports. This object specifies the number of broadcast packets per second. Setting a value of … |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.36 | ScalarsnSwMaxMacFilterPerSystem | read-only | mandatory | The maximum number of MAC Filters per system in the MAC Filter table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.37 | ScalarsnSwMaxMacFilterPerPort | read-only | mandatory | The maximum number of MAC Filters per port in the Port MAC Access Filter table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.38 | ScalarsnSwDefaultVLanId | read-write | mandatory | The VLAN ID of the DEFAULT PORT-VLAN. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.39 | ScalarsnSwGlobalAutoNegotiate | read-write | mandatory | This feature only applies to Gigabit Ethernet ports. If set to disable(0), all Gigabit Ethernet ports will be put to non- negotiation mode. If set to enable(1)… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.40 | ScalarsnSwQosMechanism | read-write | mandatory | Indicates whether the qos mechanism is strict or weighted. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.41 | ScalarsnSwSingleStpMode | read-write | mandatory | Single Spanning Tree System Mode in the Switch Group can be set either enabled or disabled and the default is disabled mode. enabled(1)...........activate Sing… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.42 | ScalarsnSwFastStpMode | read-write | mandatory | Fast Spanning Tree System Mode in the Switch Group can be set either enabled or disabled and the default is enabled mode. enabled(1)...........activate Fast Sp… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2 | NodesnVLanInfo | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1 | TablesnVLanByPortTable | not-accessible | mandatory | If snSwGroupOperMode is configured as basic mode which is VLAN by Port, Layer2 switching, then this table is valid. Each VLAN switch port could have a number o… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1 | RowsnVLanByPortEntry | not-accessible | mandatory | An entry in the VLAN By Port Information table. snVLanByPortVLanIndex = 1 and with snVLanByPortVLanId = 1 together implies all attributes applying to the Globa… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.1 | ColumnsnVLanByPortVLanIndex | read-only | mandatory | The VLAN ID index must not be greater than the snVLanGroupVlanMaxEntry. Each VLAN Identifier can have a membership of multiple ports. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.2 | ColumnsnVLanByPortVLanId | read-write | mandatory | The VLAN ID index to the VLAN By Port Info Table. Each VLAN Identifier can have a membership of multiple ports. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.3 | ColumnsnVLanByPortPortMask | read-write | mandatory | The Standand-alone switch VLAN port membership. (It is obsoleted for Chassis Product) |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.4 | ColumnsnVLanByPortQos | read-write | mandatory | The Stand alone stackable switch VLAN Priority values are: low(0) high(1) The BigIron switch VLAN Priority values are: level0(0), level1(1), level2(2), level3(… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.5 | ColumnsnVLanByPortStpMode | read-write | mandatory | Spanning Tree Mode in the Switch Group can be set either enabled or disabled and the default is enabled mode. enabled(1)...........activate Spanning Tree disab… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.6 | ColumnsnVLanByPortStpPriority | read-write | mandatory | dot1dStpPriority : The value of the write-able portion of the Stp ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of … |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.7 | ColumnsnVLanByPortStpGroupMaxAge | read-write | mandatory | dot1dStpBridgeMaxAge: From RFC1493(Bridge MIB). The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifi… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.8 | ColumnsnVLanByPortStpGroupHelloTime | read-write | mandatory | dot1dStpBridgeHelloTime: From RFC1493(Bridge MIB). The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.9 | ColumnsnVLanByPortStpGroupForwardDelay | read-write | mandatory | dot1dStpBridgeForwardDelay : From RFC1493(Bridge MIB). The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.10 | ColumnsnVLanByPortRowStatus | read-write | mandatory | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.11 | ColumnsnVLanByPortOperState | read-only | mandatory | By default, this mode is set to notActivated(0). notActivated(0)...the VLAN entry is not activated and not in running mode. activated(1)......the VLAN entry is… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.12 | ColumnsnVLanByPortBaseNumPorts | read-only | mandatory | The number of ports controlled by this bridging entity. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.13 | ColumnsnVLanByPortBaseType | read-only | mandatory | Indicates what type of bridging this bridge can perform. If a bridge is actually performing a certain type of bridging this will be indicated by entries in the… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.14 | ColumnsnVLanByPortStpProtocolSpecification | read-only | mandatory | An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE … |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.15 | ColumnsnVLanByPortStpMaxAge | read-only | mandatory | dot1dStpMaxAge: From RFC1493(Bridge MIB). The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.16 | ColumnsnVLanByPortStpHelloTime | read-only | mandatory | dot1dStpHelloTime: From RFC1493(Bridge MIB). The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the r… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.17 | ColumnsnVLanByPortStpHoldTime | read-only | mandatory | dot1dStpHoldTime: From RFC1493(Bridge MIB). This time value determines the interval length during which no more than two Configuration bridge PDUs shall be tra… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.18 | ColumnsnVLanByPortStpForwardDelay | read-only | mandatory | dot1dStpForwardDelay: From RFC1493(Bridge MIB). This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning sta… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.19 | ColumnsnVLanByPortStpTimeSinceTopologyChange | read-only | mandatory | The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.20 | ColumnsnVLanByPortStpTopChanges | read-only | mandatory | The total number of topology changes detected by this bridge since the management entity was last reset or initialized. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.21 | ColumnsnVLanByPortStpRootCost | read-only | mandatory | dot1dStpRootCost: From RFC1493(Bridge MIB). The cost of the path to the root as seen from this bridge. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.22 | ColumnsnVLanByPortStpRootPort | read-only | mandatory | dot1dStpRootPort: From RFC1493(Bridge MIB). The port number of the port which offers the lowest cost path from this bridge to the root bridge. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.23 | ColumnsnVLanByPortStpDesignatedRoot | read-only | mandatory | dot1dStpDesignatedRoot: From RFC1493(Bridge MIB). The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as execute… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.24 | ColumnsnVLanByPortBaseBridgeAddress | read-only | mandatory | The MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.25 | ColumnsnVLanByPortVLanName | read-write | mandatory | VLAN Community Name string. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.26 | ColumnsnVLanByPortRouterIntf | read-write | mandatory | Optional: A virtual interface for router to the VLAN If a SNMP-Get value is zero, that means this object was not configured. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.27 | ColumnsnVLanByPortChassisPortMask | read-write | mandatory | The Chassis VLAN switch port membership. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2 | TablesnVLanByProtocolTable | not-accessible | mandatory | . |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1 | RowsnVLanByProtocolEntry | not-accessible | mandatory | An entry in the VLAN By Protocol Configuration table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.1 | ColumnsnVLanByProtocolVLanId | read-only | mandatory | The VLAN ID index to both of the VLAN By Port Info Table and this table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.2 | ColumnsnVLanByProtocolIndex | read-only | mandatory | |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.3 | ColumnsnVLanByProtocolDynamic | read-write | mandatory | disabled(0) : disabled dynamic port inclusion - applied to switch only. enabled(1) : enabled dynamic port inclusion - applied to switch only. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.4 | ColumnsnVLanByProtocolStaticMask | read-write | mandatory | The Standand-alone switch Protocol VLAN port membership applied in static mode. (It is obsoleted for Chassis Product) |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.5 | ColumnsnVLanByProtocolExcludeMask | read-write | mandatory | The Standand-alone switch Protocol VLAN port membership applied in exclusive mode. (It is obsoleted for Chassis Product) |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.6 | ColumnsnVLanByProtocolRouterIntf | read-write | mandatory | Optional: A virtual interface for router to the VLAN If a SNMP-Get value is zero, that means this object was not configured. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.7 | ColumnsnVLanByProtocolRowStatus | read-write | mandatory | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.8 | ColumnsnVLanByProtocolDynamicMask | read-only | mandatory | The Standand-alone switch Protocol VLAN active port membership. (It is obsoleted for Chassis Product) |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.9 | ColumnsnVLanByProtocolChassisStaticMask | read-write | mandatory | The Chassis Protocol VLAN port membership applied in static mode. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.10 | ColumnsnVLanByProtocolChassisExcludeMask | read-write | mandatory | The Chassis Protocol VLAN port membership applied in exclusive mode. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.11 | ColumnsnVLanByProtocolChassisDynamicMask | read-only | mandatory | The Chassis Protocol VLAN active port membership. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.12 | ColumnsnVLanByProtocolVLanName | read-write | mandatory | VLAN Community Name string. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3 | TablesnVLanByIpSubnetTable | not-accessible | mandatory | An entry of the VLAN By IPX Network Number Table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1 | RowsnVLanByIpSubnetEntry | not-accessible | mandatory | An entry in the VLAN By IP Subnet Configuration table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.1 | ColumnsnVLanByIpSubnetVLanId | read-only | mandatory | The VLAN ID index to both of the VLAN By Port Info Table and this table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.2 | ColumnsnVLanByIpSubnetIpAddress | read-only | mandatory | Subnet IP address. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.3 | ColumnsnVLanByIpSubnetSubnetMask | read-only | mandatory | Subnet mask associated with the Subnet IP address. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.4 | ColumnsnVLanByIpSubnetDynamic | read-write | mandatory | disabled(0) : disabled dynamic port inclusion - applied to switch only. enabled(1) : enabled dynamic port inclusion - applied to switch only. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.5 | ColumnsnVLanByIpSubnetStaticMask | read-write | mandatory | The Standand-alone switch VLAN By Subnet port membership applied in static mode. (It is obsoleted for Chassis Product) |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.6 | ColumnsnVLanByIpSubnetExcludeMask | read-write | mandatory | The Standand-alone switch VLAN By Subnet port membership applied in exclusive mode. (It is obsoleted for Chassis Product) |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.7 | ColumnsnVLanByIpSubnetRouterIntf | read-write | mandatory | Optional: A virtual interface for router to the VLAN If a SNMP-Get value is zero, that means this object was not configured. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.8 | ColumnsnVLanByIpSubnetRowStatus | read-write | mandatory | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.9 | ColumnsnVLanByIpSubnetDynamicMask | read-only | mandatory | The Standand-alone switch VLAN By Subnet active port membership. (It is obsoleted for Chassis Product) |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.10 | ColumnsnVLanByIpSubnetChassisStaticMask | read-write | mandatory | The Chassis VLAN By Subnet port membership applied in static mode. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.11 | ColumnsnVLanByIpSubnetChassisExcludeMask | read-write | mandatory | The Chassis VLAN By Subnet port membership applied in exclusive mode. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.12 | ColumnsnVLanByIpSubnetChassisDynamicMask | read-only | mandatory | The Chassis VLAN By Subnet active port membership. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.13 | ColumnsnVLanByIpSubnetVLanName | read-write | mandatory | VLAN Community Name string. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4 | TablesnVLanByIpxNetTable | not-accessible | mandatory | An entry of the VLAN By IPX Network Number Table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1 | RowsnVLanByIpxNetEntry | not-accessible | mandatory | An entry in the VLAN By Ipx Network Number Configuration table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.1 | ColumnsnVLanByIpxNetVLanId | read-only | mandatory | The VLAN ID index to both of the VLAN By Port Info Table and this table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.2 | ColumnsnVLanByIpxNetNetworkNum | read-only | mandatory | IPX Network Number. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.3 | ColumnsnVLanByIpxNetFrameType | read-only | mandatory | The following IPX Frame types are operated in Layer3 VLAN such as : ipxEthernet8022(1), ipxEthernet8023(2), ipxEthernetII(3), ipxEthernetSnap(4). choose notApp… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.4 | ColumnsnVLanByIpxNetDynamic | read-write | mandatory | disabled(0) : disabled dynamic port inclusion - applied to switch only. enabled(1) : enabled dynamic port inclusion - applied to switch only. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.5 | ColumnsnVLanByIpxNetStaticMask | read-write | mandatory | The VLAN By IPX network port membership applied in static mode. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.6 | ColumnsnVLanByIpxNetExcludeMask | read-write | mandatory | The VLAN By IPX network port membership applied in exclusive mode. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.7 | ColumnsnVLanByIpxNetRouterIntf | read-write | mandatory | Optional: A virtual interface for router to the VLAN If a SNMP-Get value is zero, that means this object was not configured. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.8 | ColumnsnVLanByIpxNetRowStatus | read-write | mandatory | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.9 | ColumnsnVLanByIpxNetDynamicMask | read-only | mandatory | The VLAN By IPX network active port membership. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.10 | ColumnsnVLanByIpxNetChassisStaticMask | read-write | mandatory | The Chassis VLAN By IPX network port membership applied in static mode. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.11 | ColumnsnVLanByIpxNetChassisExcludeMask | read-write | mandatory | The Chassis VLAN By IPX network port membership applied in exclusive mode. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.12 | ColumnsnVLanByIpxNetChassisDynamicMask | read-only | mandatory | The Chassis VLAN By IPX network active port membership. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.13 | ColumnsnVLanByIpxNetVLanName | read-write | mandatory | VLAN Community Name string. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5 | TablesnVLanByATCableTable | not-accessible | mandatory | A Table Of VLAN By AppleTalk Network Number. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1 | RowsnVLanByATCableEntry | not-accessible | mandatory | An entry of the AppleTalk Cable VLAN table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1.1 | ColumnsnVLanByATCableVLanId | read-only | mandatory | The VLAN ID of a PORT VLAN of which the AppleTalk Cable VLAN was attaching to. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1.2 | ColumnsnVLanByATCableIndex | read-only | mandatory | AppleTalk Cable VLAN index number. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1.3 | ColumnsnVLanByATCableRouterIntf | read-write | mandatory | A virtual router interface to the AppleTalk Cable VLAN, only router products accept the SNMP-SET operation. The value zero indicates that virtual router interf… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1.4 | ColumnsnVLanByATCableRowStatus | read-write | mandatory | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1.5 | ColumnsnVLanByATCableChassisStaticMask | read-write | mandatory | A list of ports which are statically configured to become port members of a VLAN. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1.6 | ColumnsnVLanByATCableVLanName | read-write | mandatory | VLAN Name string. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3 | NodesnSwPortInfo | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1 | TablesnSwPortInfoTable | not-accessible | mandatory | A specific snSwPortInfo group consists of a number of switch ports. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1 | RowsnSwPortInfoEntry | not-accessible | mandatory | An entry in the snSwPortInfo table indicates the configuration on a specified port. A SNMP SET PDU for a row of the snSwPortInfoTable requires the entired sequ… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.1 | ColumnsnSwPortInfoPortNum | read-only | mandatory | The port index. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number (slot for chassis only). |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.2 | ColumnsnSwPortInfoMonitorMode | read-write | mandatory | A monitoring port is selected and its traffic will be analyzed if the mode is not disabled(0), which is the default mode. The values are: disabled(0) input(1) … |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.3 | ColumnsnSwPortInfoTagType | read-write | mandatory | For tagged port, we could have multiple VLANs per port. For untagged port or auto port, there is only one VLAN ID per port. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.4 | ColumnsnSwPortInfoChnMode | read-write | mandatory | The port can be configured to operate in either half or full duplex mode. The values are: halfDuplex(1)...half duplex mode fullDuplex(2)...full duplex mode The… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.5 | ColumnsnSwPortInfoSpeed | read-write | mandatory | The speed configuration for a port. The values are: none(0)..........link down or no traffic. sAutoSense(1)....Auto-sensing 10 or 100Mbits. s10M(2)..........10… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.6 | ColumnsnSwPortInfoMediaType | read-only | mandatory | The media type for the port. The values are: other(1).........other or unknown media. m100BaseTX(2)....100Mbits per second copper. m100BaseFX(3)....100Mbits pe… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.7 | ColumnsnSwPortInfoConnectorType | read-only | mandatory | The type of connector that the port offers. The values are: other(1)...........other or unknown connector copper(2)..........Copper connector fiber(3).........… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.8 | ColumnsnSwPortInfoAdminStatus | read-write | mandatory | The desired state of all ports. The testing(3) state indicates that no operational packets can be passed. (same as ifAdminStatus in MIB-II) |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.9 | ColumnsnSwPortInfoLinkStatus | read-only | mandatory | The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed. (same as ifOperStatus in MIB-II) |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.10 | ColumnsnSwPortInfoPortQos | read-write | mandatory | The Stand alone stackable switch Port Qos Priority values are: low(0) high(1) The BigIron Port Qos Priority values are: level0(0), level1(1), level2(2), level3… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.11 | ColumnsnSwPortInfoPhysAddress | read-only | mandatory | The port physical address. The physical address represents the switch port. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.12 | ColumnsnSwPortStatsInFrames | read-only | mandatory | The total number of packets received on the interface. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.13 | ColumnsnSwPortStatsOutFrames | read-only | mandatory | The total number of packets transmitted out of the interface. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.14 | ColumnsnSwPortStatsAlignErrors | read-only | mandatory | dot3StatsAlignmentErrors : A count of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS che… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.15 | ColumnsnSwPortStatsFCSErrors | read-only | mandatory | dot3StatsFCSErrors : A count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check. The co… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.16 | ColumnsnSwPortStatsMultiColliFrames | read-only | mandatory | dot3StatsMultipleCollisionFrames : A count of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one co… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.17 | ColumnsnSwPortStatsFrameTooLongs | read-only | mandatory | dot3StatsFrameTooLongs : A count of frames received on a particular interface that exceed the maximum permitted frame size. The count represented by an instanc… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.18 | ColumnsnSwPortStatsTxColliFrames | read-only | mandatory | A count of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collision. A frame that is counted by… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.19 | ColumnsnSwPortStatsRxColliFrames | read-only | mandatory | A count of successfully received frames on a particular interface for which transmission is inhibited by more than one collision. This object is not specified … |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.20 | ColumnsnSwPortStatsFrameTooShorts | read-only | mandatory | A count of frames received on a particular interface that below the minimum permitted frame size. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.21 | ColumnsnSwPortLockAddressCount | read-write | mandatory | The number of source MAC addresses are allowed for a port. Writing 0 to this object will allow any number of addresses. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.22 | ColumnsnSwPortStpPortEnable | read-write | mandatory | The enabled/disabled status of the port. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.23 | ColumnsnSwPortDhcpGateListId | read-write | mandatory | The ID for a DHCP gateway list entry relative to this switch port. 0 = unset or no assigned ID |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.24 | ColumnsnSwPortName | read-write | mandatory | Port Name string. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.25 | ColumnsnSwPortStatsInBcastFrames | read-only | mandatory | The total number of broadcast packets received on the interface. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.26 | ColumnsnSwPortStatsOutBcastFrames | read-only | mandatory | The total number of broadcast packets transmitted out of the interface. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.27 | ColumnsnSwPortStatsInMcastFrames | read-only | mandatory | The total number of multicast packets received on the interface. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.28 | ColumnsnSwPortStatsOutMcastFrames | read-only | mandatory | The total number of multicast packets transmitted out of the interface. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.29 | ColumnsnSwPortStatsInDiscard | read-only | mandatory | The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer pr… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.30 | ColumnsnSwPortStatsOutDiscard | read-only | mandatory | The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reaso… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.31 | ColumnsnSwPortStatsMacStations | read-only | mandatory | The total number of MAC Stations connected to the interface. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.32 | ColumnsnSwPortCacheGroupId | read-write | mandatory | Cache Group ID for the interface. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.33 | ColumnsnSwPortTransGroupId | read-write | mandatory | Transparent Group ID for the interface. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.34 | ColumnsnSwPortInfoAutoNegotiate | read-write | mandatory | This feature only applies to Gigabit Ethernet ports. If set to disable(0), port will be put to non-negotiation mode. If set to enable(1), port will start auto-… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.35 | ColumnsnSwPortInfoFlowControl | read-write | mandatory | Enable/Disbale port flow control. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.36 | ColumnsnSwPortInfoGigType | read-only | mandatory | The media type for the port. The values are: m1000BaseSX(0)....1Gbits per second fiber, with a short wavelength transceiver. m1000BaseLX(1)....1Gbits per secon… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.37 | ColumnsnSwPortStatsLinkChange | read-only | mandatory | The total number of link state change of the interface. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.38 | ColumnsnSwPortIfIndex | read-only | mandatory | In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 1213 and RFC 1573. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.39 | ColumnsnSwPortDescr | read-only | mandatory | A textual string containing the slot/port information about the interface. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.40 | ColumnsnSwPortInOctets | read-only | mandatory | The total number of octets received on the interface, including framing characters. This object is a 64-bit counter of the ifInOctets object, defined in RFC 12… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.41 | ColumnsnSwPortOutOctets | read-only | mandatory | The total number of octets transmitted out of the interface, including framing characters. This object is a 64-bit counter of the ifOutOctets object, defined i… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.42 | ColumnsnSwPortStatsInBitsPerSec | read-only | mandatory | The number of bits per second received on the interface over a 5 minutes interval. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.43 | ColumnsnSwPortStatsOutBitsPerSec | read-only | mandatory | The number of bits per second transmitted out of the interface over a 5 minutes interval. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.44 | ColumnsnSwPortStatsInPktsPerSec | read-only | mandatory | The number of packets per second received on the interface over a 5 minutes interval. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.45 | ColumnsnSwPortStatsOutPktsPerSec | read-only | mandatory | The number of packets per second transmitted out of the interface over a 5 minutes interval. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.46 | ColumnsnSwPortStatsInUtilization | read-only | mandatory | The input network utilization in hundredths of a percent over a 5 minutes interval. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.47 | ColumnsnSwPortStatsOutUtilization | read-only | mandatory | The output network utilization in hundredths of a percent over a 5 minutes interval. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.48 | ColumnsnSwPortFastSpanPortEnable | read-write | mandatory | The enabled/disabled fast span port status of the port. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.49 | ColumnsnSwPortFastSpanUplinkEnable | read-write | mandatory | The enabled/disabled fast span uplink status of the port. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.50 | ColumnsnSwPortVlanId | read-only | mandatory | The ID of a VLAN of which this port is a member. Port must be untagged. For tagged port which belongs to multiple VLANs, this object return 0 which is an inval… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.51 | ColumnsnSwPortRouteOnly | read-write | mandatory | Enable/Disable L2 switching of a routing switch port. By default, the routing switch performs routing first. If routing failed, it performs switching. Enable r… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4 | NodesnFdbInfo | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1 | TablesnFdbTable | not-accessible | mandatory | This table contains snFdb information for each station known to the system, one entry per station. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1 | RowsnFdbEntry | not-accessible | mandatory | Each entry represents the information of a static MAC station. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.1 | ColumnsnFdbStationIndex | read-only | mandatory | The FDB Station index to the Fdb Station Table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.2 | ColumnsnFdbStationAddr | read-write | mandatory | The snFdbs physical address. The physical address represents a MAC Station. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.3 | ColumnsnFdbStationPort | read-write | mandatory | Station slot/port number. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number (slot for chassis only). |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.4 | ColumnsnFdbVLanId | read-write | mandatory | The Station VLan ID. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.5 | ColumnsnFdbStationQos | read-write | mandatory | The Stand alone stackable station Qos Priority values are: low(0) high(1) The BigIron switch station Priority values are: level0(0), level1(1), level2(2), leve… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.6 | ColumnsnFdbStationType | read-write | mandatory | |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.7 | ColumnsnFdbRowStatus | read-write | mandatory | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5 | NodesnPortStpInfo | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1 | TablesnPortStpTable | not-accessible | mandatory | A specific snPortStpTable consists of a number of switch ports. This table only exists if only if snVLanByPortTable exists and snVLanByPortStpMode is enabled f… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1 | RowsnPortStpEntry | not-accessible | mandatory | An entry in the snPortStpTable indicates the configuration on a specified port. A SNMP SET PDU for a row of the snPortStpTable requires the entired sequence of… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.1 | ColumnsnPortStpVLanId | read-only | mandatory | The VLAN ID of the VLAN switch community. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.2 | ColumnsnPortStpPortNum | read-only | mandatory | The port number of the Switch. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number (slot for chassis only). |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.3 | ColumnsnPortStpPortPriority | read-write | mandatory | The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is … |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.4 | ColumnsnPortStpPathCost | read-write | mandatory | dot1dStpPortPathCost : The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends t… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.5 | ColumnsnPortStpOperState | read-only | mandatory | By default, this mode is set to notActivated(0). notActivated(0)...the Port STP entry is not activated and not in running mode. activated(1)......the Port STP … |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.6 | ColumnsnPortStpPortEnable | not-accessible | mandatory | The enabled/disabled status of the port. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.7 | ColumnsnPortStpPortForwardTransitions | not-accessible | mandatory | The number of times this port has transitioned from the Learning state to the Forwarding state. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.8 | ColumnsnPortStpPortState | read-only | mandatory | The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the … |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.9 | ColumnsnPortStpPortDesignatedCost | read-only | mandatory | The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.10 | ColumnsnPortStpPortDesignatedRoot | read-only | mandatory | The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the po… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.11 | ColumnsnPortStpPortDesignatedBridge | read-only | mandatory | The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.12 | ColumnsnPortStpPortDesignatedPort | read-only | mandatory | The Port Identifier of the port on the Designated Bridge for this port's segment. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6 | NodesnTrunkInfo | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1 | TablesnTrunkTable | not-accessible | mandatory | A specific snTrunkTable consists of a number of Trunk port-mask. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1.1 | RowsnTrunkEntry | not-accessible | mandatory | An entry in the snTrunkTable indicates the configuration on a specified Trunk port membership. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1.1.1 | ColumnsnTrunkIndex | read-only | mandatory | The number of the trunk entries can be configured. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1.1.2 | ColumnsnTrunkPortMask | read-write | mandatory | Trunk membership of the Switch. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1.1.3 | ColumnsnTrunkType | read-write | mandatory | The trunk connection type which specifies what device the trunk ports are connected to. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2 | TablesnMSTrunkTable | not-accessible | mandatory | A table contains the configuration of port members of multi-slot trunk groups. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1 | RowsnMSTrunkEntry | not-accessible | mandatory | An entry of the snMSTrunkTable. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1.1 | ColumnsnMSTrunkPortIndex | read-only | mandatory | The primary port of a trunk group. For module with Gig ports, primary port is port 1, 3, 5, 7. For module with 10/100 ports, primary port is port 1, 5, 9, 13, … |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1.2 | ColumnsnMSTrunkPortList | read-write | mandatory | A list of port indices which are the port membership of a trunk group. Each port index is a 16-bit integer in big endian order. The first port index must be th… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1.3 | ColumnsnMSTrunkType | read-write | mandatory | The trunk connection type which specifies what device the trunk ports are connected to. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1.4 | ColumnsnMSTrunkRowStatus | read-write | mandatory | To create or delete a table entry. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7 | NodesnSwSummary | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.1 | ScalarsnSwSummaryMode | read-write | mandatory | The Switch Group Configuration Summary is configured either enabled or disabled and the default is disabled mode. enabled(1)...........activate Switch Configur… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.2 | TablesnVLanByPortEosTable | not-accessible | mandatory | A table of encoded octet strings of entries in snVLanByPortTable. The number of entries is determined by packing of rows from snVLanByPortTable. If snSwSummary… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.2.1 | RowsnVLanByPortEosEntry | not-accessible | mandatory | An EOS row in the table of encoded octet strings for table snVLanByPortTable. Instance returned in Response PDU, On GETs, instance specified is the instance re… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.2.1.1 | ColumnsnVLanByPortCfgEos | read-only | mandatory | An encoded octet string. On reads it contains an integral number of rows from table snVLanByPortTable. The size of each encoded octet string is less than or eq… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.2.1.2 | ColumnsnVLanByPortVLanEosIndex | read-only | mandatory | Each VLAN EOS Buffer Identifier have a multiple VLAN table entries. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.3 | TablesnSwPortEosTable | not-accessible | mandatory | A table of encoded octet strings of entries in snSwPortInfoTable. The number of entries is determined by packing of rows from snSwPortInfoTable. If snSwSummary… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.3.1 | RowsnSwPortEosEntry | not-accessible | mandatory | An EOS row in the table of encoded octet strings for table snSwPortInfoTable. Instance returned in Response PDU, On GETs, instance specified is the instance re… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.3.1.1 | ColumnsnSwPortCfgEos | read-only | mandatory | An encoded octet string. On reads it contains an integral number of rows from table snSwPortInfoTable. The size of each encoded octet string is less than or eq… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.3.1.2 | ColumnsnSwPortEosPortNum | read-only | mandatory | The port EOS buffer index. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.4 | TablesnFdbEosTable | not-accessible | mandatory | A table of encoded octet strings of entries in snFdbTable. The number of entries is determined by packing of rows from snFdbTable. If snSwSummaryMode is disabl… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.4.1 | RowsnFdbEosEntry | not-accessible | mandatory | An EOS row in the table of encoded octet strings for table snFdbTable. Instance returned in Response PDU, On GETs, instance specified is the instance returned.… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.4.1.1 | ColumnsnFdbCfgEos | read-only | mandatory | An encoded octet string. On reads it contains an integral number of rows from table snFdbTable. The size of each encoded octet string is less than or equal to … |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.4.1.2 | ColumnsnFdbStationEosIndex | read-only | mandatory | The FDB Station Eos index to the Fdb Station Eos Buffer. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.5 | TablesnPortStpEosTable | not-accessible | mandatory | A table of encoded octet strings of entries in snPortStpTable. The number of entries is determined by packing of rows from snPortStpTable. If snSwSummaryMode i… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.5.1 | RowsnPortStpEosEntry | not-accessible | mandatory | An EOS row in the table of encoded octet strings for table snPortStpTable. Instance returned in Response PDU, On GETs, instance specified is the instance retur… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.5.1.1 | ColumnsnPortStpCfgEos | read-only | mandatory | An encoded octet string. On reads it contains an integral number of rows from table snPortStpTable. The size of each encoded octet string is less than or equal… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.8 | NodesnDhcpGatewayListInfo | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1 | TablesnDhcpGatewayListTable | not-accessible | mandatory | A table of DHCP gateway list of addresses. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1.1 | RowsnDhcpGatewayListEntry | not-accessible | mandatory | An entry in the IP Port Address table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1.1.1 | ColumnsnDhcpGatewayListId | read-only | mandatory | The ID for a DHCP gateway list entry. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1.1.2 | ColumnsnDhcpGatewayListAddrList | read-write | mandatory | The DHCP gateway address list for each DHCP gateway list ID. This list contains 1 to 8 IP addresses represented by octet string. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1.1.3 | ColumnsnDhcpGatewayListRowStatus | read-write | mandatory | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.9 | NodesnDnsInfo | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.9.1 | ScalarsnDnsDomainName | read-write | mandatory | DNS Domain Name string. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.9.2 | ScalarsnDnsGatewayIpAddrList | read-write | mandatory | The DNS Gateway IP address list. This list contains 4 IP addresses represented by octet string. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10 | NodesnMacFilter | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1 | TablesnMacFilterTable | not-accessible | mandatory | MAC filter table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1 | RowsnMacFilterEntry | not-accessible | mandatory | An entry in the MAC filter table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.1 | ColumnsnMacFilterIndex | read-only | mandatory | The table index for a filter entry. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.2 | ColumnsnMacFilterAction | read-write | mandatory | Action to take if the Mac packet match with this filter. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.3 | ColumnsnMacFilterSourceMac | read-write | mandatory | Source MAC address. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.4 | ColumnsnMacFilterSourceMask | read-write | mandatory | Source MAC subnet mask. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.5 | ColumnsnMacFilterDestMac | read-write | mandatory | Destination MAC address. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.6 | ColumnsnMacFilterDestMask | read-write | mandatory | Destination MAC subnet mask. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.7 | ColumnsnMacFilterOperator | read-write | mandatory | Type of comparison to perform. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.8 | ColumnsnMacFilterFrameType | read-write | mandatory | Frame Type: ethernet-type, LLC and SNAP types |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.9 | ColumnsnMacFilterFrameTypeNum | read-write | mandatory | Frame Type Number. 0 means NA |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.10 | ColumnsnMacFilterRowStatus | read-write | mandatory | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2 | TablesnMacFilterPortAccessTable | not-accessible | mandatory | MAC Filter port access table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2.1 | RowsnMacFilterPortAccessEntry | not-accessible | mandatory | An entry in the MAC Filter Port access table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2.1.1 | ColumnsnMacFilterPortAccessPortIndex | read-only | mandatory | The port index. For FastIron/NetIron products, port index value is from 1 to 42 For BigIron products, port index is an encoded number: The bit 0 to bit 7: port… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2.1.2 | ColumnsnMacFilterPortAccessFilters | read-write | mandatory | 1st octet correspond to 1st filter number and so on. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2.1.3 | ColumnsnMacFilterPortAccessRowStatus | read-write | mandatory | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11 | NodesnNTP | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1 | NodesnNTPGeneral | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.1 | ScalarsnNTPPollInterval | read-write | mandatory | Interval specifies how often to poll the NTP server. Each unit is one second. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.2 | ScalarsnNTPTimeZone | read-write | mandatory | Time zone. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.3 | ScalarsnNTPSummerTimeEnable | read-write | mandatory | Enable/Disable daylight saving time. This enables daylight saving time for time/date starting 02:00:00 of first Sunday in April and ending 02:00:00 of last Sun… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.4 | ScalarsnNTPSystemClock | read-write | mandatory | System clock, in the following format: octet 0: seconds after the minute [0-60] octet 1: minutes after the hour [0-59] octet 2: hours since midnight [0-23] oct… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.5 | ScalarsnNTPSync | read-write | mandatory | Initiate time synchronization to the NTP servers. For set operation, only 'synchronize(2)' is accepted. For get operation, always return 'other(1)'. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2 | TablesnNTPServerTable | not-accessible | mandatory | NTP (Network Time Protocol) server table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2.1 | RowsnNTPServerEntry | not-accessible | mandatory | An entry in the NTP server table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2.1.1 | ColumnsnNTPServerIp | read-only | mandatory | NTP server IP address. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2.1.2 | ColumnsnNTPServerVersion | read-write | mandatory | NTP server version. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2.1.3 | ColumnsnNTPServerRowStatus | read-write | mandatory | To create or delete a NTP server table entry. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12 | NodesnRadius | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1 | NodesnRadiusGeneral | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.1 | ScalarsnRadiusSNMPAccess | read-only | mandatory | Indicate whether Radius group MIB obejcts can be accessed by SNMP manager. If value is disabled, all Radius group MIB objects return 'general error'. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.2 | ScalarsnRadiusEnableTelnetAuth | read-write | mandatory | Enable/Disable telnet authentication specified by 'snRadiusLoginMethod'. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.3 | ScalarsnRadiusRetransmit | read-write | mandatory | The number of authentication query retransmissions to the Radius server. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.4 | ScalarsnRadiusTimeOut | read-write | mandatory | Interval specifies how long to wait for authentication reply from the Radius server, each unit is one second. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.5 | ScalarsnRadiusDeadTime | read-write | mandatory | Interval specifies Radius server dead time, each unit is one minute. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.6 | ScalarsnRadiusKey | read-write | mandatory | Authentication key. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.7 | ScalarsnRadiusLoginMethod | read-write | mandatory | A sequence of authentication methods. Each octet represents a method to authenticate the user login process. Each octet has the following enumeration value: en… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.8 | ScalarsnRadiusEnableMethod | read-write | mandatory | A sequence of authentication methods. Each octet represents a method to authenticate the user entering priviledge mode of the command line interface. Each octe… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.9 | ScalarsnRadiusWebServerMethod | read-write | mandatory | A sequence of authentication methods. Each octet represents a method to authenticate the user accessing the web-server. Each octet has the following enumeratio… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.10 | ScalarsnRadiusSNMPServerMethod | read-write | mandatory | A sequence of authentication methods. Each octet represents a method to authenticate the user accessing the snmp-server. Each octet has the following enumerati… |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2 | TablesnRadiusServerTable | not-accessible | mandatory | Radius server table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1 | RowsnRadiusServerEntry | not-accessible | mandatory | An entry in the Radius server table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.1 | ColumnsnRadiusServerIp | read-only | mandatory | Radius server IP address. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.2 | ColumnsnRadiusServerAuthPort | read-write | mandatory | Authentication UDP port number. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.3 | ColumnsnRadiusServerAcctPort | read-write | mandatory | Account UDP port number. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.4 | ColumnsnRadiusServerRowStatus | read-write | mandatory | To create or delete a Radius server table entry. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13 | NodesnTacacs | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1 | NodesnTacacsGeneral | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.1 | ScalarsnTacacsRetransmit | read-write | mandatory | The number of authentication query retransmissions to the Tacacs server. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.2 | ScalarsnTacacsTimeOut | read-write | mandatory | Interval specifies how long to wait for authentication reply from the Tacacs server, each unit is one second. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.3 | ScalarsnTacacsDeadTime | read-write | mandatory | Interval specifies Tacacs server dead time, each unit is one minute. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.4 | ScalarsnTacacsKey | read-write | mandatory | Authentication key. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.5 | ScalarsnTacacsSNMPAccess | read-only | mandatory | Indicate whether Tacacs group MIB obejcts can be accessed by SNMP manager. If value is disabled, all Tacacs group MIB objects return 'general error'. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2 | TablesnTacacsServerTable | not-accessible | mandatory | Tacacs server table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1 | RowsnTacacsServerEntry | not-accessible | mandatory | An entry in the Tacacs server table. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1.1 | ColumnsnTacacsServerIp | read-only | mandatory | Tacacs server IP address. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1.2 | ColumnsnTacacsServerAuthPort | read-write | mandatory | Authentication UDP port number. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1.3 | ColumnsnTacacsServerRowStatus | read-write | mandatory | To create or delete a Tacacs server table entry. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14 | NodesnQos | |||
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1 | TablesnQosProfileTable | not-accessible | mandatory | A table contains the configuration of qos profile groups. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1 | RowsnQosProfileEntry | not-accessible | mandatory | An entry of the snQosProfileTable. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1.1 | ColumnsnQosProfileIndex | read-only | mandatory | The table index of QOS Profile. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1.2 | ColumnsnQosProfileName | read-write | mandatory | Qos Profile Name string. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1.3 | ColumnsnQosProfileRequestedBandwidth | read-write | mandatory | Qos Profile Requested Bandwidth. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1.4 | ColumnsnQosProfileCalculatedBandwidth | read-only | mandatory | Qos Profile Calculated Bandwidth. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2 | TablesnQosBindTable | not-accessible | mandatory | A table contains the configuration of 802.1p to qos profile binding groups. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2.1 | RowsnQosBindEntry | not-accessible | mandatory | An entry of the snQosBindTable. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2.1.1 | ColumnsnQosBindIndex | read-only | mandatory | The table index of QOS Bind. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2.1.2 | ColumnsnQosBindPriority | read-only | mandatory | QOS bind priority. |
| 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2.1.3 | ColumnsnQosBindProfileIndex | read-write | mandatory | QOS Bind Profile Index. This is pointer to the index of snQosProfile Table. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| BridgeId | OCTET STRING (SIZE(8)) | ||
| DisplayString | OCTET STRING | ||
| MacAddress | OCTET STRING (SIZE(6)) | ||
| PhysAddress | OCTET STRING | ||
| PortMask | INTEGER | ||
| Timeout | INTEGER |