MIB Viewer

HPN-ICF-DOT11-RRM-MIB

120 objects
This MIB file is to provide the object definition of WLAN radio resource management (RRM).
Imported Objects
HPN-ICF-DOT11-REF-MIBhpnicfDot11 hpnicfDot11APElementIndex HpnicfDot11ChannelScopeType HpnicfDot11ObjectIDType HpnicfDot11RadioElementIndex HpnicfDot11RadioScopeType HpnicfDot11RadioType HpnicfDot11SSIDStringType
SNMPv2-SMIInteger32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32
SNMPv2-TCDateAndTime MacAddress RowStatus TruthValue
OIDNameAccessStatusDescription
1.3.6.1.4.1.11.2.14.11.15.2.75.8IdentityhpnicfDot11RRMThis MIB file is to provide the object definition of WLAN radio resource management (RRM).
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1NodehpnicfDot11RRMConfigGroup
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1NodehpnicfDot11RRMGlobalCfgPara
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.1ScalarhpnicfDot11RRM11nMadtMaxMcsread-writecurrentSpecify the maximum modulation and coding scheme (MCS) index for 802.11n mandatory rates. The value 255 indicates that no maximum MCS index is specified. No ma…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.2ScalarhpnicfDot11RRM11nSuptMaxMcsread-writecurrentSpecify the maximum Modulation and Coding Scheme (MCS) index for 802.11n supported rates. The specified maximum MCS index for 802.11n supported rates must be n…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.3ScalarhpnicfDot11RRM11gProtectread-writecurrentEnable/Disable dot11g protection.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.4ScalarhpnicfDot11RRM11aPwrConstrtread-writecurrentConfigure the power constraint for all 802.11a radios. The configured power constraint is advertised in beacons if spectrum management is enabled. The range of…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.5ScalarhpnicfDot11RRM11aSpectrumManagread-writecurrentEnable/Disable spectrum management for 802.11a radios. When spectrum management is enabled, the WLAN sub-system advertises power capabilities of the AP and pow…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.6ScalarhpnicfDot11RRMAutoChlAvoid11hread-writecurrentConfigure the auto-channel set as non-dot11h channels, this is, only the non-dot11h channels belonging to the country code are scanned during initial channel s…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.7ScalarhpnicfDot11RRMScanChlread-writecurrentSet the scan mode. auto: When this option is set, all channels of the country code being set are scanned. all: When this option is set, all the channels of the…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.8ScalarhpnicfDot11RRMScanRptIntvelread-writecurrentSet the scan report interval.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.9ScalarhpnicfDot11APInterfNumThreshhdread-writecurrentRepresents threshold of AP interference . If the value of AP interference exceeds this threshold, AP interference trap will be sent. If the value of this node …
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.10ScalarhpnicfDot11StaInterfNumThreshhdread-writecurrentRepresents threshold of STA interference. If the value of STA interference exceeds this threshold, STA interference trap will be sent. If the value of this nod…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.11ScalarhpnicfDot11RRM11nMultiCastMcsread-writecurrentSpecify the modulation and coding scheme (MCS) index for 802.11n multicast rates. The value 4294967295 indicates that no MCS index is specified. No MCS index i…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.12ScalarhpnicfDot11RRM11acMadtMaxNssread-writecurrentSpecify the maximum NSS index for 802.11ac mandatory rates. The value 0 indicates that no maximum NSS index is specified. No maximum NSS index is specified for…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.13ScalarhpnicfDot11RRM11acSuptMaxNssread-writecurrentSpecify the maximum NSS index for 802.11ac supported rates. The specified maximum NSS index for 802.11ac supported rates must be no less than the specified max…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.14ScalarhpnicfDot11RRM11acMultiCastNssread-writecurrentSpecify the NSS index for 802.11ac multicast rates. The value 0 indicates that no NSS index is specified. No NSS index is specified for 802.11ac multicast rate…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.15ScalarhpnicfDot11RRM11acMultiCastVhtMcsread-writecurrentSpecify the MCS index for 802.11ac multicast rates. The value 255 indicates that no MCS index is specified. No MCS index is specified for 802.11ac multicast ra…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2TablehpnicfDot11RRMRadioCfgTablenot-accessiblecurrentConfigure WLAN RRM based radio type. When 802.11b parameter is modified, 802.11g parameter will be changed at the same time. In the same way, when 802.11g para…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1RowhpnicfDot11RRMRadioCfgEntrynot-accessiblecurrentConfigure WLAN RRM based radio type. When 802.11b parameter is modified, 802.11g parameter will be changed at the same time. In the same way, when 802.11g para…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.1ColumnhpnicfDot11RRMRadioTypenot-accessiblecurrent802.11 radio type.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.2ColumnhpnicfDot11RRMCfgChlStateread-writecurrentEnable/Disable dynamic channel selection.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.3ColumnhpnicfDot11RRMCfgChlModeread-writecurrentConfigure the mode of channel selection. This node can be configured only when dynamic channel selection is enabled.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.4ColumnhpnicfDot11RRMChlProntoRadioElmtread-writecurrentSpecify the AP and radio that will change channel at next calibration cycle. 0 is returned when getting the value of this node. This node can be configured onl…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.5ColumnhpnicfDot11RRMCfgPwrStateread-writecurrentEnable/Disable dynamic power selection for the band.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.6ColumnhpnicfDot11RRMCfgPwrModeread-writecurrentConfigure the mode of transmit power control. This node can be configured only when dynamic power selection is enabled.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.7ColumnhpnicfDot11RRMPwrProntoRadioElmtread-writecurrentSpecify the AP and radio that will change power at next calibration cycle. 0 is returned when getting the value of this node. This node can be configured only …
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.8ColumnhpnicfDot11RRMCfgIntrvlread-writecurrentConfigure the calibration interval.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.9ColumnhpnicfDot11RRMCfgIntrfThresread-writecurrentConfigure the interface threshold. By default, interference observed on an operating channel is considered during dynamic frequency selection and transmit powe…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.10ColumnhpnicfDot11RRMCfgNoiseThresread-writecurrentConfigure the noise threshold.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.11ColumnhpnicfDot11RRMCfgPERThresread-writecurrentConfigure the CRC error threshold. If the percentage of CRC errors reaches the threshold, RRM will perform resource adjustment to control the situation.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.12ColumnhpnicfDot11RRMCfgToleranceFctrread-writecurrentConfigure the tolerance level. During dynamic frequency selection (DFS), the channel will be changed only if there is a better channel having lesser interferen…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.13ColumnhpnicfDot11RRMCfgAdjacencyFctrread-writecurrentConfigure the adjacency factor for the band. If transmit power control (TPC) is configured, power will be adjusted when the nth neighbor is detected. The value…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.3TablehpnicfDot11RRMAPCfgTablenot-accessiblecurrentThis table defines the RRM parameters for AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.3.1RowhpnicfDot11RRMAPCfgEntrynot-accessiblecurrentEach entry contains information of RRM parameters for AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.3.1.1ColumnhpnicfDot11RRMAPWorkModeread-writecurrentAP work mode.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4TablehpnicfDot11RRMSDRadioGroupTablenot-accessiblecurrentThis table defines RRM self-decisive radio group.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1RowhpnicfDot11RRMSDRadioGroupEntrynot-accessiblecurrentEach entry contains information of one RRM self-decisive radio group.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.1ColumnhpnicfDot11RRMSDRadioGroupIdnot-accessiblecurrentRepresents RRM self-decisive radio group ID.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.2ColumnhpnicfDot11RRMSDRadioGroupDescread-createcurrentRepresents the description of RRM self-decisive radio group.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.3ColumnhpnicfDot11RRMSDRdGrpChlHolddownTmread-createcurrentRepresents the channel holddown time of RRM self-decisive radio group.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.4ColumnhpnicfDot11RRMSDRdGrpPwrHolddownTmread-createcurrentRepresents the power holddown time of RRM self-decisive radio group.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.5ColumnhpnicfDot11RRMSDRdGroupRowStatusread-createcurrentThe row status of this table entry.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5TablehpnicfDot11RRMAPCfg2Tablenot-accessiblecurrentThis table defines the RRM parameters for AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1RowhpnicfDot11RRMAPCfg2Entrynot-accessiblecurrentEach entry contains information of RRM parameters for AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.1ColumnhpnicfDot11RRMAPSerialIDnot-accessiblecurrentSerial ID of the AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.2ColumnhpnicfDot11RRMAPIntfThresholdread-writecurrentRepresents threshold of AP interference . If the number of AP interference exceeds this threshold, AP interference trap will be sent.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.3ColumnhpnicfDot11RRMStaIntfThresholdread-writecurrentRepresents threshold of STA interference. If the number of STA interference exceeds this threshold, station interference trap will be sent.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.4ColumnhpnicfDot11RRMCoChlIntfTrapThhdread-writecurrentRepresents threshold of interference trap with current ap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.5ColumnhpnicfDot11RRMAdjChlIntfTrapThhdread-writecurrentRepresents threshold of adjacent interference trap with current ap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2NodehpnicfDot11RRMDetectGroup
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1TablehpnicfDot11RRMChlRptTablenot-accessiblecurrentThis table shows the RRM channel information of each radio on all APs.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1RowhpnicfDot11RRMChlRptEntrynot-accessiblecurrentEach entry contains information of RRM channel information of the radio on the AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.1ColumnhpnicfDot11RRMRadioIndexaccessible-for-notifycurrentRepresents index of the radio.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.2ColumnhpnicfDot11RRMChlRptChlNumaccessible-for-notifycurrentChannel number.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.3ColumnhpnicfDot11RRMChlRptChlTyperead-onlycurrentChannel type.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.4ColumnhpnicfDot11RRMChlRptChlQltyread-onlycurrentChannel quality.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.5ColumnhpnicfDot11RRMChlRptNbrCntread-onlycurrentNumber of neighbors found on the channel.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.6ColumnhpnicfDot11RRMChlRptLoadread-onlycurrentLoad observed on the channel in percentage.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.7ColumnhpnicfDot11RRMChlRptUtlzread-onlycurrentUtilization of the channel in percentage.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.8ColumnhpnicfDot11RRMChlRptIntrfread-onlycurrentInterference observed on the channel in percentage.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.9ColumnhpnicfDot11RRMChlRptPERread-onlycurrentPacket error rate observed on the channel in percentage.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.10ColumnhpnicfDot11RRMChlRptRetryRateread-onlycurrentPercentage of retransmission happened on the channel.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.11ColumnhpnicfDot11RRMChlRptNoiseread-onlycurrentNoise observed on the channel.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.12ColumnhpnicfDot11RRMChlRptRadarIndtcrread-writecurrentRadar detection status.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2TablehpnicfDot11RRMNbrInfoTablenot-accessiblecurrentThis table shows the RRM neighbor information of each radio on all APs.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1RowhpnicfDot11RRMNbrInfoEntrynot-accessiblecurrentEach entry contains information of RRM neighbor information of the radio on an AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.1ColumnhpnicfDot11RrmNbrBSSIDnot-accessiblecurrentMAC address of the AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.2ColumnhpnicfDot11RrmNbrChlread-onlycurrentChannel number on which the neighbor was found.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.3ColumnhpnicfDot11RRMNbrIntrfread-onlycurrentInterference observed on the channel in percentage by neighbor.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.4ColumnhpnicfDot11RrmNbrRSSIread-onlycurrentSignal strength of the AP in dBm.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.5ColumnhpnicfDot11RrmNbrTyperead-onlycurrentType of the AP, managed or unmanaged.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.6ColumnhpnicfDot11RrmNbrSSIDread-onlycurrentSSID of the Neighbor.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3TablehpnicfDot11RRMHistoryTablenot-accessiblecurrentThis table shows the details of the latest three channel changes and power changes applied on all APs, including time of change, reason of the change and the c…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1RowhpnicfDot11RRMHistoryEntrynot-accessiblecurrentEach entry shows the details of channel and power changes.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.1ColumnhpnicfDot11RRMHistoryIdnot-accessiblecurrentHistory number of the change.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.2ColumnhpnicfDot11RRMHistoryRecIndctrnot-accessiblecurrentHistory record type of the change.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.3ColumnhpnicfDot11RRMHistoryChlread-onlycurrentChannel on which the radio operates before/after the change of channel or power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.4ColumnhpnicfDot11RRMHistoryPwrread-onlycurrentPower of the radio before/after the change of channel or power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.5ColumnhpnicfDot11RRMHistoryLoadread-onlycurrentLoad observed on the radio in percentage before/after the change of channel or power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.6ColumnhpnicfDot11RRMHistoryUtlzread-onlycurrentUtilization of the radio in percentage before/after the change of channel or power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.7ColumnhpnicfDot11RRMHistoryIntrfread-onlycurrentInterference observed on the radio in percentage before/after the change of channel or power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.8ColumnhpnicfDot11RRMHistoryNoiseread-onlycurrentNoise observed on the radio before/after the change of channel or power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.9ColumnhpnicfDot11RRMHistoryPERread-onlycurrentPacket error rate observed on the radio in percentage before/after the change of channel or power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.10ColumnhpnicfDot11RRMHistoryRetryRateread-onlycurrentPercentage of retransmission happened on the radio before/after the change of channel or power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.11ColumnhpnicfDot11RRMHistoryChgReasonread-onlycurrentReason for the change of channel or power. The various bit positions are: |0 |Others | |1 |Coverage | |2 |Radar | |3 |Retransmission | |4 |Packets discarded | …
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.12ColumnhpnicfDot11RRMHistoryChgDateTimeread-onlycurrentThe time when the channel or power change occurred.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4TablehpnicfDot11RRMRadioNbrInfoTablenot-accessiblecurrentThis table shows the RRM neighbor information of each radio on all APs.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4.1RowhpnicfDot11RRMRadioNbrInfoEntrynot-accessiblecurrentEach entry contains information of RRM neighbor information of the radio on an AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4.1.1ColumnhpnicfDot11RRMRadioNbrAPIDnot-accessiblecurrentAP serial id.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4.1.2ColumnhpnicfDot11RRMRadioNbrRadioIDnot-accessiblecurrentRadio Id on AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4.1.3ColumnhpnicfDot11RRMRadioNbrSSIDread-onlycurrentAll neighbour SSIDs scanned by the selected radio.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3NodehpnicfDot11RRMNotifyGroup
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1NodehpnicfDot11RRMChlQltyNotifications
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1.0NodehpnicfDot11RRMChlQltyNtfPrefix
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1.0.1NotificationhpnicfDot11RRMIntrfLimitcurrentThis notification will be sent when interference on the radio exceeds the limit.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1.0.2NotificationhpnicfDot11RRMPERLimitcurrentThis notification will be sent when packet error rate on the radio exceeds the limit.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1.0.3NotificationhpnicfDot11RRMNoiseLimitcurrentThis notification will be sent when noise on the radio exceeds the limit.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.2NodehpnicfDot11RRMResChgNotifications
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.2.0NodehpnicfDot11RRMResChgNtfPrefix
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.2.0.1NotificationhpnicfDot11RRMPowerChangecurrentThis notification will be sent when power changed on the radio automatically.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.3NodehpnicfDot11RRMNotificationsVar
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.3.1ScalarhpnicfDot11NewPoweraccessible-for-notifycurrentPower of the radio after the change of power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.3.2ScalarhpnicfDot11OldPoweraccessible-for-notifycurrentPower of the radio before the change of power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4NodehpnicfDot11MonitorDetectedGroup
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1TablehpnicfDot11MonitorDetectedDevTablenot-accessiblecurrentThis table shows the devices of AP detected
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1RowhpnicfDot11MonitorDetectedDevEntrynot-accessiblecurrentEach entry contains information of detected devices.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.1ColumnhpnicfDot11MonitorDevMACnot-accessiblecurrentRepresents MAC address of the device detected.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.2ColumnhpnicfDot11MonitorDevTyperead-onlycurrentRepresents type of the device detected.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.3ColumnhpnicfDot11MonitorDevVendorread-onlycurrentRepresents vendor of the detected device.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.4ColumnhpnicfDot11MonitorDevSSIDread-onlycurrentRepresents the service set identifier for the ESS of the device which type is ap or adhoc.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.5ColumnhpnicfDot11MonitorDevBSSIDread-onlycurrentRepresents the basic service set identifier of the detected device.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.6ColumnhpnicfDot11MonitorDevChannelread-onlycurrentRepresents the channel in which the device was last detected. AP will choose the channel which has maximum signal strength as effective channel, as there is in…
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.7ColumnhpnicfDot11MonitorRadioIdread-onlycurrentRepresents the radio ID of the AP that detected the device.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.8ColumnhpnicfDot11MonitorDevMaxRSSIread-onlycurrentRepresents the maximum detected RSSI of the device in a scan report cycle.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.9ColumnhpnicfDot11MonitorDevBeaconIntvlread-onlycurrentRepresents the beacon interval for the detected device(not include the device which type is client).
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.10ColumnhpnicfDot11MonitorDevFstDctTimeread-onlycurrentRepresents the time at which the device was first detected.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.11ColumnhpnicfDot11MonitorDevLstDctTimeread-onlycurrentRepresents the time at which the device was detected last time.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.12ColumnhpnicfDot11MonitorDevClearread-writecurrentThis object is used to clear the information of the device detected in the WLAN. It will return false for get operation.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.13ColumnhpnicfDot11MonitorDevSNRread-onlycurrentRepresents the SNR of the device in a scan report cycle.
MIB Viewer