HPN-ICF-SNA-DLSW-EXT-MIB
126 objects
The MIB module for management of specific Data Link Switching protocol enhancements. DLSw is described in RFC 1795, RFC 2024 and RFC2166.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.11.2.14.11.15.2.62 | IdentityhpnicfDlswExt | The MIB module for management of specific Data Link Switching protocol enhancements. DLSw is described in RFC 1795, RFC 2024 and RFC2166. | ||
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1 | NodehpnicfDlswExtMIBObjects | |||
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1 | NodehpnicfdeNode | |||
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.1 | ScalarhpnicfdeNodeVendorID | read-write | current | The value identifies the manufacturer's IEEE-assigned Organizationally Unique Identifier (OUI) of this DLSw. This information is reported in DLSw Capabilities … |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.2 | ScalarhpnicfdeNodeIpAddrType | read-write | current | The type of ip address: IPv4 or IPv6. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.3 | ScalarhpnicfdeNodeLocalAddr | read-write | current | Local peer ip address. This ip address must have been configured for a port on the router. If no local peer ip address is configured, then this object will be … |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.4 | ScalarhpnicfdeNodePriority | read-write | current | Peer priority advertised to remote peers in the DLSw Capabilities Exchange. If an end station can reach through more than one peer, the priority of each peer w… |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.5 | ScalarhpnicfdeNodeInitPacingWindow | read-write | current | Initial pacing window size. This is the starting size of the pacing window. DLSw uses an adaptive pacing flow control algorithm that automatically adjusts to c… |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.6 | ScalarhpnicfdeNodeMaxPacingWindow | read-write | current | Maximum pacing window size. This is the largest size that the pacing window will grow to. DLSw uses an adaptive pacing flow control algorithm that automaticall… |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.7 | ScalarhpnicfdeNodeKeepAliveInterval | read-write | current | Default remote peer keepalive interval in seconds. The keepalive parameter refers to how often DLSw peers send peer keep alives to each other. These periodic m… |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.8 | ScalarhpnicfdeNodePermitDynamic | read-write | current | To accept connections from non-configured remote peer when permitDynamic is specified. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.9 | ScalarhpnicfdeNodeConnTimeout | read-write | current | Define connected state timer. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.10 | ScalarhpnicfdeNodeLocalPendTimeout | read-write | current | Define connected state timer. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.11 | ScalarhpnicfdeNodeRemotePendTimeout | read-write | current | Define connected state timer. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.12 | ScalarhpnicfdeNodeSnaCacheTimeout | read-write | current | Define connected state timer. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.13 | ScalarhpnicfdeNodeExplorerTimeout | read-write | current | Define explorer timer. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.14 | ScalarhpnicfdeNodeExplorerWaitTimeout | read-write | current | Define explorer waiting timer. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.15 | ScalarhpnicfdeNodeConfigSapList | read-write | current | The SAP list indicates which SAPs are allowed. Only SAPs with even numbers are represented, in the form of the most significant bit of the first octet represen… |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.16 | ScalarhpnicfdeNodeMaxTransmission | read-write | current | The maximum retry times for TCP packet. Default value is 5. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.17 | ScalarhpnicfdeNodeMulticastStatus | read-write | current | Multicast support status. It is disabled by default. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.18 | ScalarhpnicfdeNodeMulticastAddress | read-write | current | Multicast address. Default is 224.0.10.0. When the hpnicfdeNodeMulticastStatus is disabled, the multicast address is reset to 0.0.0.0. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.19 | ScalarhpnicfdeNodeResetTcpAll | read-write | current | Reset all TCP circuit switch. Any return value is meaningless. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.20 | ScalarhpnicfdeNodeStCapTcpNum | read-write | current | Tcp number reported in DLSw Capabilities Exchange. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.1.21 | ScalarhpnicfdeNodeTcpQueueMax | read-write | current | The max length of TCP queue. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2 | NodehpnicfdeTConn | |||
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.1 | TablehpnicfdeTConnConfigTable | not-accessible | current | This table defines the peer transport connections that will be initiated or accepted by this DLSw. This table augments dlswTConnConfigTable. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.1.1 | RowhpnicfdeTConnConfigEntry | not-accessible | current | A list of objects that define specific configuration for a DLSw peer transport connection. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.1.1.1 | ColumnhpnicfdeTConnConfigVersion | read-create | current | This value identifies which version (first octet) and release (second octet) of the DLSw standard is supported by this partner DLSw. This information is obtain… |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.1.1.2 | ColumnhpnicfdeTConnConfigPriority | read-create | current | The priority for remote peer. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.1.1.3 | ColumnhpnicfdeTConnConfigLfSize | read-create | current | The largest frame size. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.1.1.4 | ColumnhpnicfdeTConnConfigKeepaliveIntval | read-create | current | The keepalive interval value. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.1.1.5 | ColumnhpnicfdeTConnConfigBackup | read-create | current | The current remote peer is configured as the backup of another configured remote peer. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.1.1.6 | ColumnhpnicfdeTConnConfigBackupTAddr | read-create | current | It is the ip address of a configured remote peer of which the current remote peer is configrued as backup. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.1.1.7 | ColumnhpnicfdeTConnConfigBackupLinger | read-create | current | Backup peer linger. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.2 | TablehpnicfdeTConnOperTable | not-accessible | current | A list of peer transport connections. Each connected peer will create a conceptual row in the table. When the peer disconnects, the row will be deleted from th… |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.2.1 | RowhpnicfdeTConnOperEntry | not-accessible | current | A list of objects that contain spefific operational information for a DLSw peer transport connection. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.2.1.1 | ColumnhpnicfdeTConnOperPeerType | read-only | current | The current remote peer is configured when the value is 'configured'. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.2.1.2 | ColumnhpnicfdeTConnOperVendorID | read-only | current | The value identifies the manufacturer's IEEE-assigned Organizationally Unique Identifier (OUI) of remote peer. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.2.1.3 | ColumnhpnicfdeTConnOperVersionString | read-only | current | Version information of remote peer. The length up to 512 bytes. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.2.1.4 | ColumnhpnicfdeTConnOperUpTime | read-only | current | The amount of time (in seconds) since this transport connection last entered the 'connected' state. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.2.1.5 | ColumnhpnicfdeTConnOperMulticastAddress | read-only | current | When remote peer supports DLSw2.0, this node identifies its multicast address. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.2.1.6 | ColumnhpnicfdeTConnOperStCapTcpNumber | read-only | current | Number of tcp supported when capabilities exchanging. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.2.1.7 | ColumnhpnicfdeTConnOperRecvPkts | read-only | current | The number of Switch-to-Switch Protocol (SSP) messages received on this tcp transport connection. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.2.1.8 | ColumnhpnicfdeTConnOperSendPkts | read-only | current | The number of SSP messages sent on this tcp transport connection. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.2.1.9 | ColumnhpnicfdeTConnOperDropPkts | read-only | current | The number of SSP messages dropped on this tcp transport connection. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.3 | TablehpnicfdeTConnTcpConfigTable | not-accessible | current | This table defines the TCP transport connections that will be either initiated by or accepted by this DSLw. It augments the entries in dlswTConnConfigTable who… |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.3.1 | RowhpnicfdeTConnTcpConfigEntry | not-accessible | current | A list of objects that define specific configuration for a DLSw peer transport connection within the dlswTCPDomain. dlswTCPDomain is imported from DLSW-MIB (RF… |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.2.3.1.1 | ColumnhpnicfdeTConnTcpConfigQueueMax | read-create | current | Maximum output TCP queue size for this remote peer. For DLSw over TCP encapsulation, packets may be queued due to congestion of the TCP network. This variable … |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.3 | NodehpnicfdeBridge | |||
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.3.1 | TablehpnicfdeBridgeTable | not-accessible | current | A list of bridge group which is serving for DLSw. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.3.1.1 | RowhpnicfdeBridgeEntry | not-accessible | current | A list of bridge information. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.3.1.1.1 | ColumnhpnicfdeBridgeNumIndex | not-accessible | current | This value identifies the bridge number. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.3.1.1.2 | ColumnhpnicfdeBridgeRowStatus | read-create | current | RowStatus. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.3.2 | TablehpnicfdeBridgeIfTable | not-accessible | current | The list of interface on which DLSw is active. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.3.2.1 | RowhpnicfdeBridgeIfEntry | not-accessible | current | The list of bridge interface information. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.3.2.1.1 | ColumnhpnicfdeBridgeIfBrgGrp | read-create | current | This value identifies the bridge number attached to the interface. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.3.2.1.2 | ColumnhpnicfdeBridgeIfRowStatus | read-create | current | RowStatus. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.4 | NodehpnicfdeQllc | |||
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.4.1 | TablehpnicfdeQllcTable | not-accessible | current | The table defines attributes related for those QLLC that participate in data link switching. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.4.1.1 | RowhpnicfdeQllcEntry | not-accessible | current | The ifIndex belongs to the interface which link protocol is x.25. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.4.1.1.1 | ColumnhpnicfQllcX121Address | read-create | current | X.121 address. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.4.1.1.2 | ColumnhpnicfQllcLocalMac | read-create | current | The virtual MAC address used to represent the QLLC-attached link station to the rest of the DLSw network. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.4.1.1.3 | ColumnhpnicfQllcLocalSap | read-create | current | The SAP used to represent this link station. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.4.1.1.4 | ColumnhpnicfQllcRemoteMac | read-create | current | The MAC address to which DLSw should attempt to connect this link station. If this information is not available, a length of zero for this object should be ret… |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.4.1.1.5 | ColumnhpnicfQllcRemoteSap | read-create | current | The SAP of the remote station to which this link station should be connected. If this information is not available, a length of zero for this object should be … |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.4.1.1.6 | ColumnhpnicfQllcRowStatus | read-create | current | RowStatus. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.5 | NodehpnicfdeSdlc | |||
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.5.1 | TablehpnicfdeSdlcPortTable | not-accessible | current | The table defines parameters for the interfaces whose link protocol is SDLC. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.5.1.1 | RowhpnicfdeSdlcPortEntry | not-accessible | current | Sdlc port entry. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.5.1.1.1 | ColumnhpnicfdeSdlcPortRole | read-create | current | The SDLC role of interface. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.5.1.1.2 | ColumnhpnicfdeSdlcPortSendWindow | read-create | current | Size of local send window. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.5.1.1.3 | ColumnhpnicfdeSdlcPortModulo | read-create | current | Size of modulus. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.5.1.1.4 | ColumnhpnicfdeSdlcPortMaxPdu | read-create | current | Maximum bytes for incoming frames. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.5.1.1.5 | ColumnhpnicfdeSdlcPortMaxSendQueue | read-create | current | Size of hold queue. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.5.1.1.6 | ColumnhpnicfdeSdlcPortMaxTransmission | read-create | current | Number of times to retry an operation. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.5.1.1.7 | ColumnhpnicfdeSdlcPortSimultaneousEnable | read-create | current | Activate SDLC two-way simultaneous mode. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.5.1.1.8 | ColumnhpnicfdeSdlcPortTimerACK | read-create | current | Time to wait for a reply to a frame. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.5.1.1.9 | ColumnhpnicfdeSdlcPortTimerLifeTime | read-create | current | Time to wait for a reply used by secondary station. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.5.1.1.10 | ColumnhpnicfdeSdlcPortTimerPollPause | read-create | current | Time between polls for each secondary SDLC station. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.5.1.1.11 | ColumnhpnicfdeSdlcPortRowStatus | read-create | current | RowStatus. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.6 | NodehpnicfdeLlc2 | |||
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.6.1 | TablehpnicfdeLlc2PortTable | not-accessible | current | This table defines parameters for the Ethernet interface. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.6.1.1 | RowhpnicfdeLlc2PortEntry | not-accessible | current | LLC2 port entry. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.6.1.1.1 | ColumnhpnicfdeLlc2PortMaxAck | read-create | current | Maximum of I-frames received before ACK. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.6.1.1.2 | ColumnhpnicfdeLlc2PortMaxPdu | read-create | current | Maximum of LLC2 pdu length. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.6.1.1.3 | ColumnhpnicfdeLlc2PortMaxSendQueue | read-create | current | Queue for sending llc2 I-frames. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.6.1.1.4 | ColumnhpnicfdeLlc2PortMaxTransmission | read-create | current | Retry times of operations. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.6.1.1.5 | ColumnhpnicfdeLlc2PortModulo | read-create | current | Modulus of LLC2. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.6.1.1.6 | ColumnhpnicfdeLlc2PortReceiveWindow | read-create | current | Maximum number of I-frames to send before received ACK. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.6.1.1.7 | ColumnhpnicfdeLlc2PortTimerAck | read-create | current | Waiting for ACK time after sending an I-frame. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.6.1.1.8 | ColumnhpnicfdeLlc2PortTimerAckDelay | read-create | current | Maximum time allows I-frames incoming without replay ACK. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.6.1.1.9 | ColumnhpnicfdeLlc2PortTimerDetect | read-create | current | Detect the link status. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.6.1.1.10 | ColumnhpnicfdeLlc2PortTimerBusy | read-create | current | Waiting time while other LLC2 station is in busy state. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.6.1.1.11 | ColumnhpnicfdeLlc2PortTimerPoll | read-create | current | Waiting time after a P frame is sent. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.6.1.1.12 | ColumnhpnicfdeLlc2PortTimerReject | read-create | current | Waiting time after a REJ frame is sent. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.6.1.1.13 | ColumnhpnicfdeLlc2PortRowStatus | read-create | current | RowStatus. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.7 | NodehpnicfdeReachableCache | |||
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.7.1 | NodehpnicfdeRchCacheStat | |||
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.7.1.1 | ScalarhpnicfdeRchCacheMaxIndex | read-only | current | Maximum of hpnicfdeRchCacheIndex. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.7.1.2 | ScalarhpnicfdeRchCacheNextIndex | read-only | current | The next value of hpnicfdeRchCacheIndex to be assigned by the agent. A retrieval of this object atomically reserves the returned value for use by the manager t… |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.7.3 | TablehpnicfdeRchCacheTable | not-accessible | current | Reachable cache table. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.7.3.1 | RowhpnicfdeRchCacheEntry | not-accessible | current | Reachable cache entry. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.7.3.1.1 | ColumnhpnicfdeRchCacheIndex | not-accessible | current | Index of reachable cache entry. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.7.3.1.2 | ColumnhpnicfdeRchCacheStatus | read-only | current | Current status of reachable cache entry. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.7.3.1.3 | ColumnhpnicfdeRchCacheRemainTime | read-only | current | Remain time of reachable cache entry. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.7.3.1.4 | ColumnhpnicfdeRchCacheMac | read-create | current | MAC address of reachable cache entry. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.7.3.1.5 | ColumnhpnicfdeRchCacheRemoteIpAddrType | read-create | current | Remote peer ip address type. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.7.3.1.6 | ColumnhpnicfdeRchCacheRemoteIp | read-create | current | Remote peer ip address of reachable cache entry. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.7.3.1.7 | ColumnhpnicfdeRchCacheRowStatus | read-create | current | RowStatus. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.8 | NodehpnicfdeEthernetBackup | |||
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.8.1 | NodehpnicfdeEBMacMapStat | |||
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.8.1.1 | ScalarhpnicfdeEBMacMapMaxIndex | read-only | current | Maximum of hpnicfdeEBMacMapIndex. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.8.1.2 | ScalarhpnicfdeEBMacMapNextIndex | read-only | current | The next value of hpnicfdeEBMacMapIndex to be assigned by the agent. A retrieval of this object atomically reserves the returned value for use by the manager t… |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.8.3 | TablehpnicfdeEBIfTable | not-accessible | current | Information of interface which works for DLSw Ethernet redundancy. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.8.3.1 | RowhpnicfdeEBIfEntry | not-accessible | current | Parameters defined for DLSw Ethernet redundancy interface. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.8.3.1.1 | ColumnhpnicfdeEBMulticastMac | read-create | current | Multicast MAC address configured for the Ethernet redundancy of dlsw module. When Ethernet redundancy is inactive, its value is '000000000000'H. To active Ethe… |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.8.3.1.2 | ColumnhpnicfdeEBPriority | read-create | current | Priority configured for the Ethernet redundancy of DLSw module. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.8.3.1.3 | ColumnhpnicfdeEBtimer | read-create | current | Timer for the Ethernet redundancy of DLSw module. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.8.3.1.4 | ColumnhpnicfdeEBRowStatus | read-create | current | RowStatus. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.8.4 | TablehpnicfdeEBMacMapTable | not-accessible | current | MAC address mapping table. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.8.4.1 | RowhpnicfdeEBMacMapEntry | not-accessible | current | MAC address mapping entry. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.8.4.1.1 | ColumnhpnicfdeEBMacMapIndex | not-accessible | current | Index of MAC address mapping entry. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.8.4.1.2 | ColumnhpnicfdeEBMacMapLocalMac | read-create | current | Local MAC address in MAC address mapping. When creating a new conceptual row, hpnicfdeEBMacMapLocalMac and hpnicfdeEBMacMapRemoteMac should be set simultaneous… |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.8.4.1.3 | ColumnhpnicfdeEBMacMapRemoteMac | read-create | current | Remote MAC address of MAC address mapping. When creating a new conceptual row, hpnicfdeEBMacMapLocalMac and hpnicfdeEBMacMapRemoteMac should be set simultaneou… |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.8.4.1.4 | ColumnhpnicfdeEBMacMapNeighbour | read-create | current | Neighbour of MAC address mapping. |
| 1.3.6.1.4.1.11.2.14.11.15.2.62.1.8.4.1.5 | ColumnhpnicfdeEBMacMapRowStatus | read-create | current | Status of MAC address mapping entry. |