HUAWEI-VOIP-COMMON-MIB
491 objects
This MIB module defines MIB objects which provides VOIP global parameters management.
Imported Objects
| HUAWEI-MIB | huaweiUtility |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE private TimeTicks Unsigned32 |
| SNMPv2-TC | DisplayString RowStatus TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2011.6.36 | IdentityhwVoip | This MIB module defines MIB objects which provides VOIP global parameters management. | ||
| 1.3.6.1.4.1.2011.6.36.1 | NodehwIASVoipObjects | |||
| 1.3.6.1.4.1.2011.6.36.1.8 | TablehwMgDspOperateTable | not-accessible | current | This table is used to config the operation of DSP channel. The index of this table is hwMgDspOperIndex. |
| 1.3.6.1.4.1.2011.6.36.1.8.1 | RowhwMgDspOperateEntry | not-accessible | current | This table is used to config the operation of DSP channel. The index of this entry is hwMgDspOperIndex. |
| 1.3.6.1.4.1.2011.6.36.1.8.1.1 | ColumnhwMgDspOperIndex | not-accessible | current | Indicates the shelf/slot/subboard/channel index. |
| 1.3.6.1.4.1.2011.6.36.1.8.1.2 | ColumnhwMgDspOperChannelState | read-only | current | Indicates the channel status. Options: 1. idle(1) -idle 2. g711(2) -G.711 3. fault(3) -faulty 4. probit(4) -prohibited 5. pcmLoopback(5) -PCM loopback 6. ipLoo… |
| 1.3.6.1.4.1.2011.6.36.1.8.1.3 | ColumnhwMgDspOperChannelWorkMode | read-only | current | Indicates the channel status. The parameter is effective only when the channel status is busy. Options: 1. all(1) -full rate 2. g711(2) -G.711 3. wastage(3) -w… |
| 1.3.6.1.4.1.2011.6.36.1.8.1.4 | ColumnhwMgDspOperStateChange | read-only | current | Indicates the channel status changing time. |
| 1.3.6.1.4.1.2011.6.36.1.8.1.5 | ColumnhwMgDspOperAdminStatus | read-write | current | Indicates the operation type. Options: 1. prohibit(1) -prohibit 2. unprohibit(2) -unprohibit 3. pcmLoopback(3) -PCM loopback 4. ipLoopback(4) -IP loopback 5. n… |
| 1.3.6.1.4.1.2011.6.36.1.8.1.6 | ColumnhwMgDspJBInPerCent | read-only | current | Indicates the current fill level of the jitterbuffer in percent. |
| 1.3.6.1.4.1.2011.6.36.1.9 | TablehwMgDspStatisticsTable | not-accessible | current | This table is used to query the DSP channel statistics. The index of this table is hwMgDspStatisticsIndex. |
| 1.3.6.1.4.1.2011.6.36.1.9.1 | RowhwMgDspStatisticsEntry | not-accessible | current | This table is used to query the DSP channel statistics. The index of this entry is hwMgDspStatisticsIndex. |
| 1.3.6.1.4.1.2011.6.36.1.9.1.1 | ColumnhwMgDspStatisticsIndex | not-accessible | current | Bits 31-26 (six bits): shelf index Bits 25-20 (six bits): slot index Bits 19-16 (four bits): subboard index Bits 15-0 (16 bits): all F When the index is all F,… |
| 1.3.6.1.4.1.2011.6.36.1.9.1.2 | ColumnhwMgDspStatisticsTotalNum | read-only | current | Indicates the total number of DSP channels. |
| 1.3.6.1.4.1.2011.6.36.1.9.1.3 | ColumnhwMgDspStatisticsFreeNum | read-only | current | Indicates the number of idle channels. |
| 1.3.6.1.4.1.2011.6.36.1.9.1.4 | ColumnhwMgDspStatisticsG711Num | read-only | current | Indicates the number of occupied DSP channels of the G.711. |
| 1.3.6.1.4.1.2011.6.36.1.9.1.5 | ColumnhwMgDspStatisticsAllNum | read-only | current | Indicates the number of occupied DSP channels of the full rate. |
| 1.3.6.1.4.1.2011.6.36.1.9.1.6 | ColumnhwMgDspStatisticsWastageNum | read-only | current | Indicates the number of DSP channels of the wastage. |
| 1.3.6.1.4.1.2011.6.36.1.9.1.7 | ColumnhwMgDspStatisticsFaultNum | read-only | current | Indicates the number of faulty DSP channels. |
| 1.3.6.1.4.1.2011.6.36.1.9.1.8 | ColumnhwMgDspStatisticsLoopNum | read-only | current | Indicates the number of DSP channels in the loopback. |
| 1.3.6.1.4.1.2011.6.36.1.9.1.9 | ColumnhwMgDspStatisticsForbiddenNum | read-only | current | Indicates the number of prohibited DSP channels. |
| 1.3.6.1.4.1.2011.6.36.1.9.1.10 | ColumnhwMgDspSystemReserved | read-only | deprecated | Reserved for the system. |
| 1.3.6.1.4.1.2011.6.36.1.11 | TablehwMgRingTypeMapTable | not-accessible | current | This table is used to set the ring type mapping. The indexes of this table are hwMgRingTypeMapMgId, hwMgRingTypeMapRingId. |
| 1.3.6.1.4.1.2011.6.36.1.11.1 | RowhwMgRingTypeMapEntry | not-accessible | current | This table is used to set the ring type mapping. The indexes of this entry are hwMgRingTypeMapMgId, hwMgRingTypeMapRingId. |
| 1.3.6.1.4.1.2011.6.36.1.11.1.1 | ColumnhwMgRingTypeMapMgId | not-accessible | current | Indicates the MG ID. The range of MG ID from 0 to 16777215 is for AG system, value of 33554431 is only for PBX system and the value input from 16777215 to 3355… |
| 1.3.6.1.4.1.2011.6.36.1.11.1.2 | ColumnhwMgRingTypeMapRingId | not-accessible | current | Indicates the ring ID. The range of ring ID from 0 to 15 is for AG system,When the system is PBX the range of ring ID is 0 to 15,and 255 is also valid. When th… |
| 1.3.6.1.4.1.2011.6.36.1.11.1.3 | ColumnhwMgRingTypeMapCascadeRingType | read-write | current | Indicates the cadence ring type. Enumerated types: 1-Null, 2-Normal ring 1:4, 3-Special ring 1:2, 4-Special ring 0.4:0.2:0.4:4, 5-Long ring, 6-Special ring 1.2… |
| 1.3.6.1.4.1.2011.6.36.1.11.1.4 | ColumnhwMgRingTypeMapInitRingType | read-write | current | Indicates the initial ring type. Enumeration type: 1-Null, 2-Normal ring (FSK) 1:4, 3-Special ring (FSK) 1:2, 4-Special ring (FSK) 0.4:0.2:0.4:4, 5-Special rin… |
| 1.3.6.1.4.1.2011.6.36.1.11.1.5 | ColumnhwMgRingTypeMapRowStatus | read-write | current | Indicates the row status (the SIP supports only 4 and 6). |
| 1.3.6.1.4.1.2011.6.36.1.11.1.6 | ColumnhwMgRingTypeMapName | read-write | current | Indicates the ring type mapping name. |
| 1.3.6.1.4.1.2011.6.36.1.12 | TablehwMgCallInfoTable | not-accessible | current | This table is use to query the information in the call. The index of this table is hwMgCallInfoIndex. |
| 1.3.6.1.4.1.2011.6.36.1.12.1 | RowhwMgCallInfoEntry | not-accessible | current | This table is use to query the information in the call. The index of this entry is hwMgCallInfoIndex. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.1 | ColumnhwMgCallInfoIndex | not-accessible | current | Indicates the shelf/slot/port. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.2 | ColumnhwMgCallInfoRTPPort | read-only | current | Indicates the local RTP port. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.3 | ColumnhwMgCallInfoDSPPlace | read-only | current | Indicates the DSP channel (the shelf/slot/channel index). |
| 1.3.6.1.4.1.2011.6.36.1.12.1.4 | ColumnhwMgCallInfoCodec | read-only | current | Indicates the enumerated definition of the VoiceCode. Note that several items in the enumerated definition are not consecutive. In the definition below, G723Lo… |
| 1.3.6.1.4.1.2011.6.36.1.12.1.5 | ColumnhwMgCallInfoPackagTime | read-only | current | Indicates the codex packetizing duration. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.6 | ColumnhwMgCallInfoVAD | read-only | current | Indicates voice activity detection. Options: 1. true(1) -detect voice activity 2. false(2) -not detect voice activity |
| 1.3.6.1.4.1.2011.6.36.1.12.1.7 | ColumnhwMgCallInfoEC | read-only | current | Indicates echo cancel. Options: 1. true(1) -echo cancel 2. false(2) -disable echo cancel |
| 1.3.6.1.4.1.2011.6.36.1.12.1.8 | ColumnhwMgCallInfoJitBuffer | read-only | current | Indicates the local JitBuffer value. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.9 | ColumnhwMgCallInfoTransGain | read-only | current | Indicates the transmit gain (0-20 correspond to -10 dB to +10 dB). |
| 1.3.6.1.4.1.2011.6.36.1.12.1.10 | ColumnhwMgCallInfoRecvGain | read-only | current | Indicates the receive gain (0-15 correspond to -10 dB to +5 dB). |
| 1.3.6.1.4.1.2011.6.36.1.12.1.11 | ColumnhwMgCallInfoRemoteRTPPort | read-only | current | Indicates the remote RTP port. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.12 | ColumnhwMgCallInfoLocalIP | read-only | current | Indicates the local IP address. The value 255.255.255.255 is returned if the entry is invalid. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.13 | ColumnhwMgCallInfoRemoteIP | read-only | current | Indicates the remote IP address. The value 255.255.255.255 is returned if the entry is invalid. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.14 | ColumnhwMgCallInfoDuration | read-only | current | Indicates the occupied duration. Unit: second |
| 1.3.6.1.4.1.2011.6.36.1.12.1.15 | ColumnhwMgCallInfoRTCPState | read-only | current | Indicates the RTCP status (whether it is enabled). Options: 1. on(1) -enable rtcp 2. off(2) -disable rtcp 3. notReported(3) -not report rtcp |
| 1.3.6.1.4.1.2011.6.36.1.12.1.16 | ColumnhwMgCallInfoRmtPackagTime | read-only | current | Indicates the remote packetizing duration. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.17 | ColumnhwMgCallInfoRcvPackageNum | read-only | current | Indicates the count of received packets. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.18 | ColumnhwMgCallInfoSndPackageNum | read-only | current | Indicates the count of sent packets. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.19 | ColumnhwMgCallInfoRcvOctsNum | read-only | current | Indicates the count of received octets. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.20 | ColumnhwMgCallInfoSndOctsNum | read-only | current | Indicates the count of sent octets. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.21 | ColumnhwMgCallInfoLoopDelay | read-only | current | Indicates the loop delay. Unit: millisecond |
| 1.3.6.1.4.1.2011.6.36.1.12.1.22 | ColumnhwMgCallInfoLocalJitter | read-only | current | Indicates the local Jitter. Unit: millisecond |
| 1.3.6.1.4.1.2011.6.36.1.12.1.23 | ColumnhwMgCallInfoRmtJitter | read-only | current | Indicates the remote Jitter. Unit: millisecond |
| 1.3.6.1.4.1.2011.6.36.1.12.1.24 | ColumnhwMgCallInfoLocalLossRate | read-only | current | Indicates the local packet loss rate (%). 1 means 1%. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.25 | ColumnhwMgCallInfoRmtLossRate | read-only | current | Indicates the remote packet loss rate (%). 1 means 1%. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.26 | ColumnhwMgCallInfoMos | read-only | current | MOS(MOS:Mean Opinion Score) value. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.27 | ColumnhwMgCallInfoVlanID | read-only | current | Vlan ID. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.28 | ColumnhwMgCallInfoVlanPriority | read-only | current | Vlan priority. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.29 | ColumnhwMgCallInfoQoSStrategy | read-only | current | QoS strategy. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.30 | ColumnhwMgCallInfoQoSValue | read-only | current | QoS value. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.31 | ColumnhwMgCallInfoNplr | read-only | current | Network Packet Loss Rate(%). 1 means 1%. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.32 | ColumnhwMgCallInfoJdr | read-only | current | Jitter Buffer Discard Rate(%). 1 means 1%. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.33 | ColumnhwMgCallInfoRtd | read-only | current | RTCP Round-Trip Delay. Unit: millisecond |
| 1.3.6.1.4.1.2011.6.36.1.12.1.34 | ColumnhwMgCallInfoEsd | read-only | current | End System Delay. Unit: millisecond |
| 1.3.6.1.4.1.2011.6.36.1.12.1.35 | ColumnhwMgCallInfoSl | read-only | current | Signal Level. Unit: db |
| 1.3.6.1.4.1.2011.6.36.1.12.1.36 | ColumnhwMgCallInfoNl | read-only | current | Noise Level. Unit: db |
| 1.3.6.1.4.1.2011.6.36.1.12.1.37 | ColumnhwMgCallInfoRerl | read-only | current | Residual Echo Return Loss. Unit: db |
| 1.3.6.1.4.1.2011.6.36.1.12.1.38 | ColumnhwMgCallInfoRFactor | read-only | current | R Factor. Range: 0-100 |
| 1.3.6.1.4.1.2011.6.36.1.12.1.39 | ColumnhwMgCallInfoMoslq | read-only | current | Estimated MOSLQ(a voice quality metric on a scale from 1 to 5). |
| 1.3.6.1.4.1.2011.6.36.1.12.1.40 | ColumnhwMgCallInfoBld | read-only | current | Burst Loss Density(%). 1 means 1%. |
| 1.3.6.1.4.1.2011.6.36.1.12.1.41 | ColumnhwMgCallInfoGd | read-only | current | Gap Duration. Unit: millisecond |
| 1.3.6.1.4.1.2011.6.36.1.12.1.42 | ColumnhwMgCallInfoBd | read-only | current | Burst Duration. Unit: millisecond |
| 1.3.6.1.4.1.2011.6.36.1.12.1.43 | ColumnhwMgCallInfoGld | read-only | current | Gap Loss Density(%). 1 means 1%. |
| 1.3.6.1.4.1.2011.6.36.1.25 | NodehwDspAttributeTable | |||
| 1.3.6.1.4.1.2011.6.36.1.25.1 | ScalarhwFaxMaxTrainRate | read-write | current | Indicates the maximum fax training rate. Options: 1. v17(1) -V17 2. v29(2) -V29 3. v27(3) -V27 Default: v17(1) |
| 1.3.6.1.4.1.2011.6.36.1.25.2 | ScalarhwFaxTrainMode | read-write | current | Indicates the fax training mode. Options: 1. remoteTrain(1) -remote train 2. localTrain(2) -local train Default: remoteTrain(1) |
| 1.3.6.1.4.1.2011.6.36.1.25.3 | ScalarhwDSPMaxJitterBuffer | read-write | obsolete | Indicates the max JitterBuffer value of DSP channel. Unit: millisecond Default: 120 |
| 1.3.6.1.4.1.2011.6.36.1.25.4 | ScalarhwDSPAttrInputGain | read-write | obsolete | Indicates the input gain of DSP chip (0-15 correspond to -10 dB to +5 dB). Default: 10 |
| 1.3.6.1.4.1.2011.6.36.1.25.5 | ScalarhwDSPAttrOutputGain | read-write | obsolete | Indicates the output gain of DSP chip (0-20 correspond to -10 dB to +10 dB). Default: 10 |
| 1.3.6.1.4.1.2011.6.36.1.25.6 | ScalarhwDSPCodeType | read-write | current | Indicates the default coding type of DSP channel. It is unavailable in the SIP Options: 1. g711A(1) -G.711A 2. g711u(2) -G.711U 3. g723(3) -G.723 4. g729(4) -G… |
| 1.3.6.1.4.1.2011.6.36.1.25.7 | ScalarhwRTCPPackageSendInterval | read-write | current | Indicates the RTCP packet sending interval of DSP channel. The valid value must be no less than 500, 0 indicates that the parameter is disabled. Default: 5000 … |
| 1.3.6.1.4.1.2011.6.36.1.25.8 | ScalarhwDSPRtpPacketInterval | read-write | current | Indicates the default RTP packet time of DSP channel. Options: 1. packettime5ms(5) - 5ms 2. packettime10ms(10) - 10ms 3. packettime20ms(20) - 20ms 4. packettim… |
| 1.3.6.1.4.1.2011.6.36.1.25.9 | ScalarhwDSPEchoCheck | read-write | current | Indicates the default echo check switch of DSP channel. It is unavailable in the SIP. Options: 1. disable(1) -disable 2. enable(2) -enable Default: enable(2) |
| 1.3.6.1.4.1.2011.6.36.1.25.10 | ScalarhwDSPSilenceReduce | read-write | current | Indicates the default silence compression switch of DSP channel. It is unavailable in the SIP. Options: 1. disable(1) -disable silence compression 2. enable(2)… |
| 1.3.6.1.4.1.2011.6.36.1.25.11 | ScalarhwDSPNeedStatisOrNot | read-write | current | Indicate whether DSP channel needs the channel statistics. It is unavailable in the SIP. Options: 1. disable(1) -close 2. enable(2) -open Default: disable(1) |
| 1.3.6.1.4.1.2011.6.36.1.25.12 | ScalarhwDSPClearmodePayload | read-write | current | Indicates the default payload type of the DSP channel clearmode (it must not conflict with the payload used). Default: 100 |
| 1.3.6.1.4.1.2011.6.36.1.25.13 | ScalarhwSevereDegradethreshold | read-write | current | Indicates the default threshold of severely packet loss seconds. |
| 1.3.6.1.4.1.2011.6.36.1.25.14 | ScalarhwBvqm | read-write | current | Indicates the VQM switch. Options: 1. disable(1) -disable 2. enable(2) -enable |
| 1.3.6.1.4.1.2011.6.36.1.25.15 | ScalarhwDSPPlc | read-write | current | Indicates the DSP packet loss compensation algorithm. Options: 1. disable(1) -disable 2. enable(2) -enable Default: disable(1) |
| 1.3.6.1.4.1.2011.6.36.1.25.16 | ScalarhwDSPMinAdaptJitterBuffer | read-write | current | Minimum adapt jitterbuffer of DSP. MinAdaptJitterBuffer<=InitAdaptJitterBuffer<=MaxAdaptJitterBuffer and the MinAdaptJitterBuffer<ThresholdJitterBuffer. Unit: … |
| 1.3.6.1.4.1.2011.6.36.1.25.17 | ScalarhwDSPMaxAdaptJitterBuffer | read-write | current | Maximum adapt jitterbuffer of DSP. MinAdaptJitterBuffer<=InitAdaptJitterBuffer<=MaxAdaptJitterBuffer and the MinAdaptJitterBuffer<ThresholdJitterBuffer. Unit: … |
| 1.3.6.1.4.1.2011.6.36.1.25.18 | ScalarhwDSPInitAdaptJitterBuffer | read-write | current | Initial adapt jitterbuffer of DSP. MinAdaptJitterBuffer<=InitAdaptJitterBuffer<=MaxAdaptJitterBuffer and the MinAdaptJitterBuffer<ThresholdJitterBuffer. Unit: … |
| 1.3.6.1.4.1.2011.6.36.1.25.19 | ScalarhwDSPMinFixedJitterBuffer | read-write | current | Minimum fixed jitterbuffer of DSP. MinFixedJitterBuffer<=NormalFixedJitterBuffer<=MaxFixedJitterBuffer and the MinAdaptJitterBuffer <ThresholdJitterBuffer. Uni… |
| 1.3.6.1.4.1.2011.6.36.1.25.20 | ScalarhwDSPMaxFixedJitterBuffer | read-write | current | Maximum fixed jitterbuffer of DSP. MinFixedJitterBuffer<=NormalFixedJitterBuffer<=MaxFixedJitterBuffer and the MinAdaptJitterBuffer<ThresholdJitterBuffer. Unit… |
| 1.3.6.1.4.1.2011.6.36.1.25.21 | ScalarhwDSPNormalFixedJitterBuffer | read-write | current | Initial fixed jitterbuffer of DSP. MinFixedJitterBuffer<=NormalFixedJitterBuffer<=MaxFixedJitterBuffer and the MinAdaptJitterBuffer<ThresholdJitterBuffer. Unit… |
| 1.3.6.1.4.1.2011.6.36.1.25.22 | Scalarhw2198Payload | read-write | current | Indicates the payload type value of 2198 (it must not conflict with the payload used). |
| 1.3.6.1.4.1.2011.6.36.1.25.23 | ScalarhwRedundancyT30 | read-write | current | Indicates the T30 redundancy parameter of T38 Fax. |
| 1.3.6.1.4.1.2011.6.36.1.25.24 | ScalarhwRedundancyT4 | read-write | current | Indicates the T4 redundancy parameter of T38 Fax. |
| 1.3.6.1.4.1.2011.6.36.1.25.25 | ScalarhwDSPRTCPXR | read-write | current | The switch of RTCP XR. Options: 1. enable(1) -enable RTCP XR 2. disable(2) -disable RTCP XR |
| 1.3.6.1.4.1.2011.6.36.1.25.26 | ScalarhwG726R32kPayload | read-write | current | Indicates the payload type value of G.726-32k (it must not conflict with the payload used). |
| 1.3.6.1.4.1.2011.6.36.1.25.27 | ScalarhwFaxV8Negotiate | read-write | current | Indicates the switch of the V8 negotiation of FAX. Options: 1. enable(1) -enable 2. disable(2) -disable Default: disable(2) |
| 1.3.6.1.4.1.2011.6.36.1.25.28 | ScalarhwDSPModeJitterBuffer | read-write | current | Set JitterBuffer mode of DSP channel. Options: 1. adaptive(1) -adaptive 2. fixed(2) -fixed Default: adaptive(1) |
| 1.3.6.1.4.1.2011.6.36.1.25.29 | ScalarhwVbdPayload | read-write | current | Indicates the payload type value of VBD (it must not conflict with the payload used). |
| 1.3.6.1.4.1.2011.6.36.1.25.30 | ScalarhwRfc2833Payload | read-write | current | Indicates the payload type value of RFC2833 (it must not conflict with the payload used). |
| 1.3.6.1.4.1.2011.6.36.1.25.31 | ScalarhwG726R16kPayload | read-write | current | Indicates the payload type value of G.726-16k (it must not conflict with the payload used). |
| 1.3.6.1.4.1.2011.6.36.1.25.32 | ScalarhwG726R24kPayload | read-write | current | Indicates the payload type value of G.726-24k (it must not conflict with the payload used). |
| 1.3.6.1.4.1.2011.6.36.1.25.33 | ScalarhwG726R40kPayload | read-write | current | Indicates the payload type value of G.726-40k (it must not conflict with the payload used). |
| 1.3.6.1.4.1.2011.6.36.1.25.34 | ScalarhwDspAutoVBDSwitchMode | read-write | current | VBD switch mode. Options: 1. hostControl(1) -host control 2. autoSwitch(2) -auto switch Default: hostControl(1) |
| 1.3.6.1.4.1.2011.6.36.1.25.35 | ScalarhwDSPAlarmAdaptJitterBuffer | read-write | current | Adapt jitterbuffer of DSP alarm threshold. Unit: millisecond |
| 1.3.6.1.4.1.2011.6.36.1.25.36 | ScalarhwDspFixedJbUpImmediately | read-write | current | Enable DSP fixed JB adjust upward immediately or not. Options: 1. enable(1) -enable 2. disable(2) -disable |
| 1.3.6.1.4.1.2011.6.36.1.25.37 | ScalarhwDspMediaBreakTimer | read-write | current | Media Break Timer. 0-indicates that the detection is disabled. Unit: second |
| 1.3.6.1.4.1.2011.6.36.1.25.38 | ScalarhwCngLevel | read-write | current | Comfort noise generation level. Unit: -dB |
| 1.3.6.1.4.1.2011.6.36.1.25.39 | ScalarhwG168SilenceDetectTime | read-write | current | Indicates the duration of ITU-T G.168 bi-directional VAD. Unit: ms |
| 1.3.6.1.4.1.2011.6.36.1.25.40 | ScalarhwT38JitterBuffer | read-write | current | Indicates the fixed jitter buffer of T38 Fax. Unit: ms |
| 1.3.6.1.4.1.2011.6.36.1.25.41 | ScalarhwDtmfDetectNegativeTwistAdjust | read-write | current | Indicates the adjust of DTMF detect negative twist. Unit: 0.1dB |
| 1.3.6.1.4.1.2011.6.36.1.25.42 | ScalarhwDtmfDetectPositiveTwistAdjust | read-write | current | Indicates the adjust of DTMF detect positive twist. Unit: 0.1dB |
| 1.3.6.1.4.1.2011.6.36.1.25.43 | ScalarhwDtmfDetectLevelLowerAdjust | read-write | current | Indicates the adjust of DTMF detect level lower. Unit: 0.1dB |
| 1.3.6.1.4.1.2011.6.36.1.25.44 | ScalarhwDtmfDetectSnrAdjust | read-write | current | Indicates the adjust of DTMF detect SNR. Unit: 0.1dB |
| 1.3.6.1.4.1.2011.6.36.1.25.45 | ScalarhwV22Usb1EcCtrl | read-write | current | Indicates the EC switch for V.22 USB1 event. Options: 1. on(1) -on 2. off(2) -off Default: off(2) |
| 1.3.6.1.4.1.2011.6.36.1.25.46 | ScalarhwAnsamEcCtrl | read-write | current | Indicates the EC switch for ANSam event. Options: 1. on(1) -on 2. off(2) -off Default: off(2) |
| 1.3.6.1.4.1.2011.6.36.1.25.47 | ScalarhwRfc2833DurationAlgorithm | read-write | current | Indicates the RFC2833 event duration algorithm. Options: 1. irregular(1) -Increased at a irregular interval 2. regular(2) -Increased at a regular interval Defa… |
| 1.3.6.1.4.1.2011.6.36.1.26 | NodehwFaxParametersTable | |||
| 1.3.6.1.4.1.2011.6.36.1.26.1 | ScalarhwFAXTransfersMode | read-write | deprecated | Indicates the fax transmission mode. Options: 1. thoroughly(1) -transparent transmission 2. selfT38(2) -auto-negotiation T.38 3. v3Flow(3) -V3 flow 4. selfswit… |
| 1.3.6.1.4.1.2011.6.36.1.26.2 | ScalarhwT38FaxPortAdd2OrNot | read-write | current | Indicates the T38 fax port. Options: 1. rtpPortAdd0(1) -the udp port of FAX is as same as the voice's 2. rtpPortAdd2(2) -the udp port of FAX is the voice's add… |
| 1.3.6.1.4.1.2011.6.36.1.26.3 | ScalarhwFaxPacketInterval10msGlobal | read-write | current | Enable packet interval of fax to use only 10ms or not. Options: 1. enable(1) -enable 2. disable(2) -disable Default: disable(2) |
| 1.3.6.1.4.1.2011.6.36.1.26.4 | ScalarhwFaxRFC2198 | read-write | current | whether the fax support the RFC2198, 1:DisableRfc2198SmartStartup, 2:EnableRfc2198SmartStartup, 3: ImmediatelyStartupRFC2198 Default: 1 |
| 1.3.6.1.4.1.2011.6.36.1.26.5 | ScalarhwFaxNegotiateMode | read-write | current | The negotiate mode of fax. Options: 1. selfswitch(1) -self switch 2. controledbyMGC(2) -controled by MGC Default: controledbyMGC(2) |
| 1.3.6.1.4.1.2011.6.36.1.26.6 | ScalarhwFaxFlow | read-write | current | The negotiate flow of fax. Options: 1. v2(1) -Version 1 2. v3(2) -Version 2 3. v5(3) -Version 3 Default: v3(2) |
| 1.3.6.1.4.1.2011.6.36.1.26.7 | ScalarhwFaxWorkMode | read-write | current | Indicates the fax transmission mode. Options: 1. thoroughly(1) -use voice codec 2. t38(2) -use T.38 codec Default: thoroughly(1) |
| 1.3.6.1.4.1.2011.6.36.1.26.8 | ScalarhwFaxParametersVbdCodec | read-write | current | Indicates the codec of VBD. Options: 1. g711A(1) -G.711A 2. g711U(2) -G.711U Default: g711A(1) |
| 1.3.6.1.4.1.2011.6.36.1.26.9 | ScalarhwFaxParametersVbdPtType | read-write | current | Indicates the payload type of VBD. Options: 1. static(1) -static payload type 2. dynamic(2) -dynamic payload type Default: static(1) |
| 1.3.6.1.4.1.2011.6.36.1.26.10 | ScalarhwFaxTransEvent | read-write | current | Indicates the mode of sending fax event. In controlled_by_MGC scheme, sending fax event via 2833 depends on the signalling. In rfc2833 scheme, the device alway… |
| 1.3.6.1.4.1.2011.6.36.1.27 | NodehwModemParametersTable | |||
| 1.3.6.1.4.1.2011.6.36.1.27.1 | ScalarhwModemTransfersMode | read-write | current | Indicates the modem transmission mode. Options: 1. thoroughly(1) -transparent transmission 2. relay(2) -relay mode Default: thoroughly(1) |
| 1.3.6.1.4.1.2011.6.36.1.27.2 | ScalarhwModemEventMode | read-write | current | Indicates the modem event report mode. Options: 1. delay(1)-delay mode 2. direct(2) -direct mode 3. directForHighSpeedSignals(3) -direct for high-speed signals |
| 1.3.6.1.4.1.2011.6.36.1.27.3 | ScalarhwModemPacketInterval10msGlobal | read-write | current | Enable packet interval of modem to use only 10ms or not. Options: 1. enable(1) -enable 2. disable(2) -disable Default: disable(2) |
| 1.3.6.1.4.1.2011.6.36.1.27.4 | ScalarhwModemRFC2198 | read-write | current | Whether the modem support RFC2198. 1:DisableRfc2198SmartStartup, 2:EnableRfc2198SmartStartup, 3: ImmediatelyStartupRFC2198 Default: 1 |
| 1.3.6.1.4.1.2011.6.36.1.27.5 | ScalarhwModemNegotiateMode | read-write | current | The negotiate mode of modem. Options: 1. selfswitch(1) -self switch 2. controledbyMGC(2) -controled by MGC Default: controledbyMGC(2) |
| 1.3.6.1.4.1.2011.6.36.1.27.6 | ScalarhwModemParametersVbdCodec | read-write | current | Indicates the codec of VBD. Options: 1. g711A(1) -G.711A 2. g711U(2) -G.711U Default: g711A(1) |
| 1.3.6.1.4.1.2011.6.36.1.27.7 | ScalarhwModemParametersVbdPtType | read-write | current | Indicates the payload type of VBD. Options: 1. static(1) -static payload type 2. dynamic(2) -dynamic payload type Default: static(1) |
| 1.3.6.1.4.1.2011.6.36.1.27.8 | ScalarhwModemTransEvent | read-write | current | Indicates the mode of sending modem event. In controlled_by_MGC scheme, sending modem event via 2833 depends on the signalling. In rfc2833 scheme, the device a… |
| 1.3.6.1.4.1.2011.6.36.1.27.9 | ScalarhwModemDtmfFallbackVoice | read-write | current | Enable fallback to voice mode or not, when detect DTMF from IP side. Options: 1. enable(1) -enable 2. disable(2) -disable Default: disable(2) |
| 1.3.6.1.4.1.2011.6.36.1.33 | NodehwMgDspWorkModeTable | |||
| 1.3.6.1.4.1.2011.6.36.1.33.1 | ScalarhwMgDspMode | read-write | current | Indicates the value of the working mode of the DSP channel. 0-0% full rate; 1-10% full rate; 2-20% full rate; 3-30% full rate; 4-40% full rate; 5-50% full rate… |
| 1.3.6.1.4.1.2011.6.36.1.35 | NodehwBandwidthParaTable | |||
| 1.3.6.1.4.1.2011.6.36.1.35.1 | ScalarhwBandwidthSupport | read-write | current | Indicates whether the MG restricts calls in case of insufficient bandwidth. Options: 1. yes(1) -support 2. no(2) -not support Default: no(2) |
| 1.3.6.1.4.1.2011.6.36.1.35.2 | ScalarhwBandwidthMax | read-write | current | Indicates the value of the maximum upstream bandwidth. Default: 1000 Unit: 100 kbs |
| 1.3.6.1.4.1.2011.6.36.1.35.3 | ScalarhwBandwidthReserved | read-write | current | Indicates the value of the bandwidth reserved for emergency calls (%). Default: 10 Unit: 100 kbit/s |
| 1.3.6.1.4.1.2011.6.36.1.36 | TablehwUserStatisticTable | not-accessible | current | This table is used to query the statistics of online subscribers. The index of this table is hwUserStatisticMgId. |
| 1.3.6.1.4.1.2011.6.36.1.36.1 | RowhwUserStatisticEntry | not-accessible | current | This table is used to query the statistics of online subscribers. The index of this entry is hwUserStatisticMgId. |
| 1.3.6.1.4.1.2011.6.36.1.36.1.1 | ColumnhwUserStatisticMgId | not-accessible | current | Indicates the MG ID. |
| 1.3.6.1.4.1.2011.6.36.1.36.1.2 | ColumnhwUserStatisticPstn | read-only | current | Indicates the count of online PSTN subscribers. |
| 1.3.6.1.4.1.2011.6.36.1.36.1.3 | ColumnhwUserStatisticFax | read-only | current | Indicates the count of online fax subscribers. |
| 1.3.6.1.4.1.2011.6.36.1.36.1.4 | ColumnhwUserStatisticModem | read-only | current | Indicates the count of online modem subscribers. |
| 1.3.6.1.4.1.2011.6.36.1.36.1.5 | ColumnhwUserStatisticBra | read-only | current | Indicates the count of online BRA subscribers. |
| 1.3.6.1.4.1.2011.6.36.1.36.1.6 | ColumnhwUserStatisticPra | read-only | current | Indicates the count of online PRA subscribers. |
| 1.3.6.1.4.1.2011.6.36.1.36.1.7 | ColumnhwUserStatisticDpnss | read-only | current | Indicates the count of online DPNSS subscribers. |
| 1.3.6.1.4.1.2011.6.36.1.36.1.8 | ColumnhwUserStatisticDass2 | read-only | current | Indicates the count of online DASS2 subscribers. |
| 1.3.6.1.4.1.2011.6.36.1.36.1.9 | ColumnhwUserStatisticR2 | read-only | current | Indicates the count of online R2 subscribers. |
| 1.3.6.1.4.1.2011.6.36.1.43 | NodehwProtocolSupportTable | |||
| 1.3.6.1.4.1.2011.6.36.1.43.1 | ScalarhwProtocolActive | read-only | current | The bit table indicates the protocol that is currently used. The bit table from low bit to high bit are H248, MGCP and SIP. For example, the bit table value fo… |
| 1.3.6.1.4.1.2011.6.36.1.43.2 | ScalarhwProtocolConfig | read-write | current | The bit table indicates the protocol supported by the system after the system resets. The bit table from low bit to high bit are H248, MGCP and SIP. For exampl… |
| 1.3.6.1.4.1.2011.6.36.1.43.3 | ScalarhwFeatureProtocolConfig | read-write | current | Indicates the voice feature supported by the system after the system resets. AG+H248(0) AG+MGCP(1) AG+SIP(2) PBX+SIP(3) PBX+NONE(4) |
| 1.3.6.1.4.1.2011.6.36.1.43.4 | ScalarhwFeatureProtocolActive | read-only | current | Indicates the voice feature that is currently used. AG+H248(0) AG+MGCP(1) AG+SIP(2) PBX+SIP(3) PBX+NONE(4) |
| 1.3.6.1.4.1.2011.6.36.1.45 | TablehwE2ETraceTaskTable | not-accessible | current | This table is used to config the E2E tracing task. The index of this table is hwE2ETraceTaskID. |
| 1.3.6.1.4.1.2011.6.36.1.45.1 | RowhwE2ETraceTaskEntry | not-accessible | current | This table is used to config the E2E tracing task. The index of this entry is hwE2ETraceTaskID. |
| 1.3.6.1.4.1.2011.6.36.1.45.1.1 | ColumnhwE2ETraceTaskID | not-accessible | current | Indicates the tracing task ID. Bit 31 (1 bit): 0 Bit 30 (1 bit): the protocol type (1-H.248; 0-MGCP) Bits 29-16 (14 bits): the terminal ID Bits 15-0 (16 bits):… |
| 1.3.6.1.4.1.2011.6.36.1.45.1.2 | ColumnhwE2ETraceTaskOperType | read-write | current | Indicates the operation type. Options: 1. invalid(-1) -invalid value 2. delete(1) -delete |
| 1.3.6.1.4.1.2011.6.36.1.45.1.3 | ColumnhwE2ETraceTaskSessionID | read-only | current | Indicates the session ID. |
| 1.3.6.1.4.1.2011.6.36.1.45.1.4 | ColumnhwE2ETraceTaskMsgReptCyc | read-only | current | Indicates the message reporting period. |
| 1.3.6.1.4.1.2011.6.36.1.45.1.5 | ColumnhwE2ETraceTaskChkCyc | read-only | current | Indicates the task checking period. |
| 1.3.6.1.4.1.2011.6.36.1.45.1.6 | ColumnhwE2ETraceTaskMsgType | read-only | current | Indicates the message type. Options: 1. h248(24) -H.248 2. mgcp(25) -MGCP |
| 1.3.6.1.4.1.2011.6.36.1.45.1.7 | ColumnhwE2ETraceTaskFTPLnkState | read-only | current | Indicates the FTP connection status. Options: 1. establishing(0) -establishing 2. data(1) -transfering data 3. trying(2) -trying 4. releasing(3) -releasing 5. … |
| 1.3.6.1.4.1.2011.6.36.1.45.1.8 | ColumnhwE2ETraceTaskURLInfoPort | read-only | current | Indicates the port number of the URL message. |
| 1.3.6.1.4.1.2011.6.36.1.45.1.9 | ColumnhwE2ETraceTaskURLInfoIP | read-only | current | Indicates the IP address of the URL message. |
| 1.3.6.1.4.1.2011.6.36.1.45.1.10 | ColumnhwE2ETraceTaskURLInfoPath | read-only | current | Indicates the path of the URL message. |
| 1.3.6.1.4.1.2011.6.36.1.45.1.11 | ColumnhwE2ETraceTaskURLInfoFileName | read-only | current | Indicates the file name of the URL message. |
| 1.3.6.1.4.1.2011.6.36.1.45.1.12 | ColumnhwE2ETraceTaskUserMgID | read-only | current | Indicates the interface ID of the subscriber traced by the tracing task. |
| 1.3.6.1.4.1.2011.6.36.1.45.1.13 | ColumnhwE2ETraceTaskUserTerminationID | read-only | current | Indicates the terminal ID of the tracing task subscriber. |
| 1.3.6.1.4.1.2011.6.36.1.46 | NodehwE2ETraceTaskAttrTable | |||
| 1.3.6.1.4.1.2011.6.36.1.46.1 | ScalarhwE2ETraceTaskAttrTimerLgth | read-write | current | Indicates the value of the tracing task attribute, that is, the timer for reporting the null message. Default: 60 Unit: second |
| 1.3.6.1.4.1.2011.6.36.1.46.2 | ScalarhwE2ETraceTaskAttrKey | read-write | current | Indicates the FTP decryption key. - means to delete this key. Default: E2ETraceKey_1 |
| 1.3.6.1.4.1.2011.6.36.1.46.3 | ScalarhwE2ETraceTaskAttrFtpType | read-write | current | Indicates the FTP type. Options: 1. ftp(1) -ftp 2. sftp(2) -sftp 3. auto(3) -auto Default: auto(3) |
| 1.3.6.1.4.1.2011.6.36.1.59 | NodehwQosThresholdTable | |||
| 1.3.6.1.4.1.2011.6.36.1.59.1 | ScalarhwQosThresholdJitter | read-write | current | Indicates the jitter alarm threshold. Default: 60 Unit: millisecond |
| 1.3.6.1.4.1.2011.6.36.1.59.2 | ScalarhwQosThresholdLoopdelay | read-write | current | Indicates the loop delay alarm threshold. Default: 400 Unit: millisecond |
| 1.3.6.1.4.1.2011.6.36.1.59.3 | ScalarhwQosThresholdPacketlost | read-write | current | Indicates the packet loss rate alarm threshold. Default: 5 Unit: 1/100. |
| 1.3.6.1.4.1.2011.6.36.1.62 | NodehwClipParametersCfgTable | |||
| 1.3.6.1.4.1.2011.6.36.1.62.1 | ScalarhwOnHookDualToneAlertLevel | read-write | current | Power of Dual Tone Alert in onhook state. Support 16 electric: 1: -5.5dBm0, 2: -6.5dBm0, 3: -7.5dBm0, 4: -8.5dBm0, 5: -9.5dBm0, 6: -10.5dBm0 7: -11.5dBm0, 8: -… |
| 1.3.6.1.4.1.2011.6.36.1.62.2 | ScalarhwOnHookFSKLevel | read-write | current | Power of FSK level in onhook state. Support 16 electric: 1: -5.5dBm0, 2: -6.5dBm0, 3: -7.5dBm0, 4: -8.5dBm0, 5: -9.5dBm0, 6: -10.5dBm0 7: -11.5dBm0, 8: -12.5dB… |
| 1.3.6.1.4.1.2011.6.36.1.62.3 | ScalarhwOffHookDualToneAlertLevel | read-write | current | Power of Dual Tone Alert in offhook state. Support 16 electric: 1: -5.5dBm0, 2: -6.5dBm0, 3: -7.5dBm0, 4: -8.5dBm0, 5: -9.5dBm0, 6: -10.5dBm0 7: -11.5dBm0, 8: … |
| 1.3.6.1.4.1.2011.6.36.1.62.4 | ScalarhwOffHookFSKLevel | read-write | current | Power of FSK level in offhook state. Support 16 electric: 1: -5.5dBm0, 2: -6.5dBm0, 3: -7.5dBm0, 4: -8.5dBm0, 5: -9.5dBm0, 6: -10.5dBm0 7: -11.5dBm0, 8: -12.5d… |
| 1.3.6.1.4.1.2011.6.36.1.62.5 | ScalarhwOnHookChnSeizure | read-write | current | Channel seize bits for onhook FSK. Default: 300 |
| 1.3.6.1.4.1.2011.6.36.1.62.6 | ScalarhwOnHookMarkSignal | read-write | current | Mark signal for onhook FSK. \ Default: 180 |
| 1.3.6.1.4.1.2011.6.36.1.62.7 | ScalarhwOnHookSendFskInterval | read-write | current | The interval between DT-AS and FSK when onhook. Default: 250 Unit: millisecond. |
| 1.3.6.1.4.1.2011.6.36.1.62.8 | ScalarhwOnHookDtAsDur | read-write | current | The duration for DT-AS when onhook. Default: 100 Unit: millisecond. |
| 1.3.6.1.4.1.2011.6.36.1.62.9 | ScalarhwOffHookMarkSignal | read-write | current | Mark signal for offhook FSK. Default: 80 |
| 1.3.6.1.4.1.2011.6.36.1.62.10 | ScalarhwOffHookDetectTeAckInterval | read-write | current | The interval between DT-AS and detecting terminal ack when offhook. Default: 80 |
| 1.3.6.1.4.1.2011.6.36.1.62.11 | ScalarhwOffHookSendFskInterval | read-write | current | The interval between detecting terminal ack and sending FSK when offhook. Default: 50 Unit: millisecond. |
| 1.3.6.1.4.1.2011.6.36.1.62.12 | ScalarhwOffHookDtAsDur | read-write | current | The duration for DT-AS when offhook. Default: 80 Unit: millisecond. |
| 1.3.6.1.4.1.2011.6.36.1.62.13 | ScalarhwOnHookDtmfNumStartCode | read-write | current | The DTMF number start code. 12(A) 13(B) 14(C) 15(D) Default: 15(D) |
| 1.3.6.1.4.1.2011.6.36.1.65 | TablehwTidTemplateConfigTable | not-accessible | current | This table is used to config terminal ID template. The index of this table is hwTidTemplateId. |
| 1.3.6.1.4.1.2011.6.36.1.65.1 | RowhwTidTemplateConfigEntry | not-accessible | current | This table is used to config terminal ID template. The index of this entry is hwTidTemplateId. |
| 1.3.6.1.4.1.2011.6.36.1.65.1.1 | ColumnhwTidTemplateId | not-accessible | current | Indicates the TID profile index. TID profiles 0-18 are the default profiles in the system. The default TID profiles can be referenced but can not be added, mod… |
| 1.3.6.1.4.1.2011.6.36.1.65.1.2 | ColumnhwTidFormat | read-write | current | Indicates the format string of the TID profile. |
| 1.3.6.1.4.1.2011.6.36.1.65.1.3 | ColumnhwTidParameterlist | read-write | current | Indicates the parameter list of the TID profile. |
| 1.3.6.1.4.1.2011.6.36.1.65.1.4 | ColumnhwTidTemplateName | read-write | current | Indicates the TID profile name. The profile name must be unique. |
| 1.3.6.1.4.1.2011.6.36.1.65.1.5 | ColumnhwTidTemplateRowStatus | read-write | current | Indicates the row status of the TID profile. Profiles 0-31 cannot be added, deleted, or modified. |
| 1.3.6.1.4.1.2011.6.36.1.65.1.6 | ColumnhwIsNeedToConfigTID | read-only | current | Indicates whether the TID needs to be input when adding the subscriber who uses this profile. Options: 1. no(1) -TID needs not to be input when adding the subs… |
| 1.3.6.1.4.1.2011.6.36.1.69 | NodehwVoipCommonObjects | |||
| 1.3.6.1.4.1.2011.6.36.1.69.1 | TablehwFaxParaTable | not-accessible | current | This table is used to config the fax parameter. The index of this table is hwFaxParaVgwId. |
| 1.3.6.1.4.1.2011.6.36.1.69.1.1 | RowhwFaxParaEntry | not-accessible | current | This table is used to config the fax parameter. The index of this entry is hwFaxParaVgwId. |
| 1.3.6.1.4.1.2011.6.36.1.69.1.1.1 | ColumnhwFaxParaVgwId | not-accessible | current | Indicates the interface ID. |
| 1.3.6.1.4.1.2011.6.36.1.69.1.1.2 | ColumnhwFaxMode | read-write | deprecated | Indicates the fax transmission mode. 1-Transparent transmission; 2-Auto-negotiation T.38; 3-V3 flow; 4-Stand-alone transparent transmission; 5-V5 flow; 6-Self-… |
| 1.3.6.1.4.1.2011.6.36.1.69.1.1.3 | ColumnhwFaxPacketInterval10ms | read-write | current | Enable packet interval of fax to use only 10ms or not. Options: 1. enable(1) -enable 2. disable(2) -disable Default: disable(2) |
| 1.3.6.1.4.1.2011.6.36.1.69.1.1.4 | ColumnhwFaxRedundancyFlag | read-write | deprecated | Use fax redundancy parameter or not .1:enable,to use. 2:disable,not to use. This leaf only valid in sip transparent fax. |
| 1.3.6.1.4.1.2011.6.36.1.69.1.1.5 | ColumnhwFaxNegoMode | read-write | current | The negotiate mode of fax. Options: 1. negotiate(1) -negotiate 2. selfswitch(2) -do not negotiate Default: negotiate(1) |
| 1.3.6.1.4.1.2011.6.36.1.69.1.1.6 | ColumnhwFaxTransMode | read-write | current | Indicates the fax transmission mode. Options: 1. thoroughly(1) -use voice codec 2. t38(2) - use T.38 codec Default: thoroughly(1) |
| 1.3.6.1.4.1.2011.6.36.1.69.1.1.7 | ColumnhwFaxRfc2198NegoMode | read-write | deprecated | Use fax redundancy parameter or not. Options: 1. negoStart(1) -negotiate start 2. fixedStart(2) -fixed start 3. noInitiativeStart(3) -no Initiative Start Defau… |
| 1.3.6.1.4.1.2011.6.36.1.69.1.1.8 | ColumnhwFaxRfc2198StartMode | read-write | deprecated | Whether the fax support the RFC2198 Smart Startup. Options: 1. smart2198(1) -smart start 2198 2. ordinary2198(2) -ordinary 2198 Default: ordinary2198(2) |
| 1.3.6.1.4.1.2011.6.36.1.69.1.1.9 | ColumnhwFaxParaVbdCodec | read-write | current | Indicates the codec of VBD. Options: 1. g711A(1) -G.711A 2. g711U(2) -G.711U Default: g711A(1) |
| 1.3.6.1.4.1.2011.6.36.1.69.1.1.10 | ColumnhwFaxParaVbdPtType | read-write | current | Indicates the payload type of VBD. Options: 1. static(1) -static payload type 2. dynamic(2) -dynamic payload type Default: static(1) |
| 1.3.6.1.4.1.2011.6.36.1.69.1.1.11 | ColumnhwFaxTransEventType | read-write | deprecated | Indicates the mode of sending fax event, whether support the RFC2833. Options: 1. negoStart(1) -negotiation start 2. fixedStart(2) -fix start 3. noInitiativeSt… |
| 1.3.6.1.4.1.2011.6.36.1.69.1.1.12 | ColumnhwFaxVbdAttributeType | read-write | current | Indicate the format of session attribute lines when starting fax VBD Negotiation. Options: 1. v152(1) -v.152 format 2. chinatelecom(2) -chinatelecom format 3. … |
| 1.3.6.1.4.1.2011.6.36.1.69.1.1.13 | ColumnhwFaxRtpInterval | read-write | current | Indicates the default RTP packet time of DSP channel. Options: 1. packettime5ms(1) -5ms 2. packettime10ms(2) -10ms 3. packettime20ms(3) -20ms 4. packettime30ms… |
| 1.3.6.1.4.1.2011.6.36.1.69.2 | TablehwModemParaTable | not-accessible | current | This table is used to config the modem parameter. The index of this table is hwModemParaVgwId. |
| 1.3.6.1.4.1.2011.6.36.1.69.2.1 | RowhwModemParaEntry | not-accessible | current | This table is used to config the modem parameter. The index of this entry is hwModemParaVgwId. |
| 1.3.6.1.4.1.2011.6.36.1.69.2.1.1 | ColumnhwModemParaVgwId | not-accessible | current | Indicates the interface ID. |
| 1.3.6.1.4.1.2011.6.36.1.69.2.1.2 | ColumnhwModemMode | read-write | deprecated | Indicates the modem transmission mode. 1-Negotiation mode; 2-Stand-alone mode. |
| 1.3.6.1.4.1.2011.6.36.1.69.2.1.3 | ColumnhwModemRedundancyFlag | read-write | deprecated | Indicates the flag of using the modem redundancy parameter. 1-enable; 2-disable . |
| 1.3.6.1.4.1.2011.6.36.1.69.2.1.4 | ColumnhwModemPacketInterval10ms | read-write | current | Enable packet interval of modem to use only 10ms or not. Options: 1. enable(1) -enable 2. disable(2) -disable Default: disable(2) |
| 1.3.6.1.4.1.2011.6.36.1.69.2.1.5 | ColumnhwModemNegoMode | read-write | current | The negotiate mode of fax. Options: 1. negotiate(1) -negotiate 2. selfswitch(2) -do not negotiate Default: negotiate(1) |
| 1.3.6.1.4.1.2011.6.36.1.69.2.1.6 | ColumnhwModemTransMode | read-write | current | Indicates the fax transmission mode. Options: 1. thoroughly(1) -thoroughly transmission 2. relay(2) -Relay mode Default: thoroughly(1) |
| 1.3.6.1.4.1.2011.6.36.1.69.2.1.7 | ColumnhwModemRfc2198NegoMode | read-write | deprecated | Use modem redundancy parameter or not. Options: 1. negoStart(1) -negotiate start 2. fixedStart(2) -fixed start 3. noInitiativeStart(3) -no initiative start Def… |
| 1.3.6.1.4.1.2011.6.36.1.69.2.1.8 | ColumnhwModemRfc2198StartMode | read-write | deprecated | whether the modem support the RFC2198 Smart Startup. Options: 1. smart2198(1) -smart 2198 2. ordinary2198(2) -ordinary 2198 Default: ordinary2198(2) |
| 1.3.6.1.4.1.2011.6.36.1.69.2.1.9 | ColumnhwModemParaVbdCodec | read-write | current | Indicates the codec of VBD. Options: 1. g711A(1) -G.711A 2. g711U(2) -G.711U Default: g711A(1) |
| 1.3.6.1.4.1.2011.6.36.1.69.2.1.10 | ColumnhwModemParaVbdPtType | read-write | current | Indicates the payload type of VBD. Options: 1. static(1) -static payload type 2. dynamic(2) -dynamic payload type Default: static(1) |
| 1.3.6.1.4.1.2011.6.36.1.69.2.1.11 | ColumnhwModemTransEventType | read-write | deprecated | Indicates the mode of sending fax event, whether support the RFC2833. Options: 1. negoStart(1) -negotiate start 2. fixedStart(2) -fixed start 3. noInitiativeSt… |
| 1.3.6.1.4.1.2011.6.36.1.69.2.1.12 | ColumnhwModemVbdAttributeType | read-write | current | Indicate the format of session attribute lines when starting modem VBD Negotiation. Options: 1. v152(1) -V.152 2. chinatelecom(2) -china telecom 3. extchinatel… |
| 1.3.6.1.4.1.2011.6.36.1.69.2.1.13 | ColumnhwModemRtpInterval | read-write | current | Indicates the default RTP packet time of DSP channel. Options: 1. packettime5ms(1) -5ms 2. packettime10ms(2) -10ms 3. packettime20ms(3) -20ms 4. packettime30ms… |
| 1.3.6.1.4.1.2011.6.36.1.69.2.1.14 | ColumnhwModemParaDtmfFallbackVoice | read-write | current | Enable fallback to voice mode or not, when detect DTMF from IP side. Options: 1. enable(1) -enable 2. disable(2) -disable Default: disable(2) |
| 1.3.6.1.4.1.2011.6.36.1.69.3 | TablehwRfc2833Table | not-accessible | current | This table is used to config the rfc2833 parameter. The index of this table is hwRfc2833VgwId. |
| 1.3.6.1.4.1.2011.6.36.1.69.3.1 | RowhwRfc2833Entry | not-accessible | current | This table is used to config the rfc2833 parameter. The index of this entry is hwRfc2833VgwId. |
| 1.3.6.1.4.1.2011.6.36.1.69.3.1.1 | ColumnhwRfc2833VgwId | not-accessible | current | Indicates the interface ID. |
| 1.3.6.1.4.1.2011.6.36.1.69.3.1.2 | ColumnhwRfc2833NegoMode | read-write | current | Indicates the start mode of the rfc2833. Options: 1. negoStart(1) -negotiate start 2. fixedStart(2) -fixed start 3. noInitiativeStart(3) -no initiative start D… |
| 1.3.6.1.4.1.2011.6.36.1.69.3.1.3 | ColumnhwRfc2833FaxModem | read-write | current | Indicates the flag of fax and modem event using rfc2833 parameter. Options: 1. enable(1) -enable 2. disable(2) -disable Default: enable(1) |
| 1.3.6.1.4.1.2011.6.36.1.69.3.1.4 | ColumnhwRfc2833FlashHook | read-write | current | Indicates the flag of flash hook event using rfc2833 parameter. Options: 1. enable(1) -enable 2. disable(2) -disable Default: disable(2) |
| 1.3.6.1.4.1.2011.6.36.1.69.3.1.5 | ColumnhwRfc2833Dtmf | read-write | current | Indicates the flag of dtmf using rfc2833 parameter. Options: 1. enable(1) -enable 2. disable(2) -disable Default: enable(1) |
| 1.3.6.1.4.1.2011.6.36.1.69.3.1.6 | ColumnhwRfcComplied | read-write | current | Indicates the type of RFC standard compliance. Options: 1. rfc2833(1) - comply with RFC2833 2. rfc4733(2) - comply with RFC4733 Default: rfc2833(1) |
| 1.3.6.1.4.1.2011.6.36.1.69.4 | TablehwRfc2198Table | not-accessible | current | This table is used to config the rfc2198 parameter. The index of this table is hwRfc2198VgwId. |
| 1.3.6.1.4.1.2011.6.36.1.69.4.1 | RowhwRfc2198Entry | not-accessible | current | This table is used to config the rfc2198 parameter. The index of this entry is hwRfc2198VgwId. |
| 1.3.6.1.4.1.2011.6.36.1.69.4.1.1 | ColumnhwRfc2198VgwId | not-accessible | current | Indicates the interface ID. |
| 1.3.6.1.4.1.2011.6.36.1.69.4.1.2 | ColumnhwRfc2198NegoMode | read-write | current | Indicates the start mode of the rfc2198. Options: 1. negoStart(1) -negotiate start 2. fixedStart(2) -fixed start 3. noInitiativeStart(3) -no initiative start D… |
| 1.3.6.1.4.1.2011.6.36.1.69.4.1.3 | ColumnhwRfc2198StartMode | read-write | current | Indicates the start mode of the rfc2198. Options: 1. smart2198(1) -smart start RFC2198 2. ordinary2198(2) -start RFC2198 ordinary Default: ordinary2198(2) |
| 1.3.6.1.4.1.2011.6.36.1.69.4.1.4 | ColumnhwRfc2198Rfc2833 | read-write | current | Indicates the flag of rfc2833 with using rfc2198. Options: 1. enable(1) -enable 2. disable(2) -disable Default: disable(2) |
| 1.3.6.1.4.1.2011.6.36.1.69.4.1.5 | ColumnhwRfc2198Vbd | read-write | current | Indicates the flag of the VBD using rfc2198. Options: 1. enable(1) -enable 2. disable(2) -disable Default: disable(2) |
| 1.3.6.1.4.1.2011.6.36.1.69.4.1.6 | ColumnhwRfc2198Voice | read-write | current | Indicates the flag of voice using rfc2198. Options: 1. enable(1) -enable 2. disable(2) -disable Default: disable(2) |
| 1.3.6.1.4.1.2011.6.36.1.69.5 | TablehwDtmfParaTable | not-accessible | current | This table is used to config the dtmf parameter. The index of this table is hwDtmfVgwId. |
| 1.3.6.1.4.1.2011.6.36.1.69.5.1 | RowhwDtmfParaEntry | not-accessible | current | This table is used to config the dtmf parameter. The index of this entry is hwDtmfVgwId. |
| 1.3.6.1.4.1.2011.6.36.1.69.5.1.1 | ColumnhwDtmfVgwId | not-accessible | current | Indicates the interface ID. |
| 1.3.6.1.4.1.2011.6.36.1.69.5.1.2 | ColumnhwDtmfTransMode | read-write | current | Indicates the transmission mode of DTMF. Options: 1. thoroughly(1) -transparent transmission 2. erase(2) -erase DTMF Default: thoroughly(1) |
| 1.3.6.1.4.1.2011.6.36.1.69.5.1.3 | ColumnhwDtmfBufferMode | read-write | current | Indicates the buffer mode for DTMF digits. Options: 1. enable(1) -enable the buffer function 2. disable(2) -disable the buffer function 3. adapt(3) -determined… |
| 1.3.6.1.4.1.2011.6.36.1.152 | NodehwDtmfParametersTable | |||
| 1.3.6.1.4.1.2011.6.36.1.152.1 | ScalarhwDtmfTransfersMode | read-write | current | Indicates the transmission mode of DTMF. If protocol is SIP please use hwDtmfTransMode. Options: 1. thoroughly(1) -transparent transmission 2. rfc2833(2) -2833… |
| 1.3.6.1.4.1.2011.6.36.1.152.2 | ScalarhwDtmfBUFMode | read-write | current | Indicates the buffer mode for DTMF digits. Options: 1: enable(1) -enable the buffer function 2: disable(2) -disable the buffer function 3: adapt(3) -determined… |
| 1.3.6.1.4.1.2011.6.36.1.154 | TablehwServiceNumCfgTable | not-accessible | current | This table is used to config the binding between service number and DSP parameters template. The index of this table is hwServiceNumMap. |
| 1.3.6.1.4.1.2011.6.36.1.154.1 | RowhwServiceNumCfgEntry | not-accessible | current | This table is used to config the binding between service number and DSP parameters template. The index of this entry is hwServiceNumMap. |
| 1.3.6.1.4.1.2011.6.36.1.154.1.1 | ColumnhwServiceNumMap | not-accessible | current | Indicates the service number digital map. |
| 1.3.6.1.4.1.2011.6.36.1.154.1.2 | ColumnhwDspParaTemplateName | read-write | current | Indicates the dsp parameters template name |
| 1.3.6.1.4.1.2011.6.36.1.154.1.3 | ColumnhwServiceNumRowStatus | read-write | current | Indicates the row status. |
| 1.3.6.1.4.1.2011.6.36.1.155 | TablehwDspParaTemplateCfgTable | not-accessible | current | This table is used to config the dsp parameters template. The index of this table is hwDspTemplateName. |
| 1.3.6.1.4.1.2011.6.36.1.155.1 | RowhwDspParaTemplateCfgEntry | not-accessible | current | This table is used to config the dsp parameters template. The index of this entry is hwDspTemplateName. |
| 1.3.6.1.4.1.2011.6.36.1.155.1.1 | ColumnhwDspTemplateName | not-accessible | current | Indicates the dsp parameters template name. |
| 1.3.6.1.4.1.2011.6.36.1.155.1.2 | ColumnhwDspEc | read-write | current | Indicates the echo cotrol. Options: 1. open(1) -open 2. close(2) -close 3. invalid(256) -invalid value, use global config Default: invalid(256) |
| 1.3.6.1.4.1.2011.6.36.1.155.1.3 | ColumnhwDspJbMode | read-write | current | Indicates the jitterbuffer mode. Options: 1. adapted(1) -adapted mode 2. fixed(2) -fixed mode 3. invalid(256) -invalid value, use global config Default: invali… |
| 1.3.6.1.4.1.2011.6.36.1.155.1.4 | ColumnhwDspNlp | read-write | current | Indicates the NLP mode. Options: 1. close(1) -close mode 2. normal(2) -normal mode 3. enhanced(3) -enhanced mode 4. reduced(4) -reduced mode 5. ecgain(5) -ecga… |
| 1.3.6.1.4.1.2011.6.36.1.155.1.5 | ColumnhwDspWorkMode | read-write | current | Indicates the dsp workmode. Options: 1. voice(1) -voice mode 2. fax(2) -fax mode 3. modem(3) -modem mode 4. invalid(256) -invalid value, use global config Defa… |
| 1.3.6.1.4.1.2011.6.36.1.155.1.6 | ColumnhwDspSc | read-write | current | Indicates the silence cotrol. Options: 1. open(1)-open 2. close(2) -close 3. invalid(256)-invalid value, use global config Default: invalid(256) |
| 1.3.6.1.4.1.2011.6.36.1.155.1.7 | ColumnhwDspTemplateRowStatus | read-write | current | Indicates the row status. |
| 1.3.6.1.4.1.2011.6.36.1.155.1.8 | ColumnhwDspInputGain | read-write | current | Indicates the input gain of DSP chip: -1 0-15 Default: -1 |
| 1.3.6.1.4.1.2011.6.36.1.155.1.9 | ColumnhwDspOutputGain | read-write | current | Indicates the output gain of DSP chip: -1 0-20 Default: -1 |
| 1.3.6.1.4.1.2011.6.36.1.155.1.10 | ColumnhwDspDtmfPara | read-write | current | Indicates the transmission mode of DTMF. Options: 1. globalConfig(1) -global config; 2. rfc2833(2) -2833 transmission; 3. erase(3) -erase DTMF; 4. rfc2833with2… |
| 1.3.6.1.4.1.2011.6.36.1.155.1.11 | ColumnhwDsp2833ForDataevent | read-write | current | Indicates the mode of sending fax/modem event. Options: 1. enable(1) -2833 2. globalConfig(2) -global config Default: globalConfig(2) |
| 1.3.6.1.4.1.2011.6.36.1.155.1.12 | ColumnhwDspSpecialFlow | read-write | current | Indicates the dsp special flow. 0 1 2 3 4 5 6-254 255 Default: 255 |
| 1.3.6.1.4.1.2011.6.36.1.155.1.13 | ColumnhwDsp2198ForVbd | read-write | current | Flag of locally starting the 2198 redundancy VBD function. Options: 1. enable(1) -enable 2198 for vbd 2. globalConfig(2) -global config: use the global config |
| 1.3.6.1.4.1.2011.6.36.1.155.1.14 | ColumnhwDspTemplateFixedJbUpImmediately | read-write | current | Enable dsp fixed JB adjust upward immediately or not. Options: 1. enable(1) -enable 2. disable(2) -disable 3. invalid(256)-invalid value, use global config Def… |
| 1.3.6.1.4.1.2011.6.36.1.155.1.15 | ColumnhwDsp2198ForVoice | read-write | current | Flag of locally starting the 2198 redundancy VOICE function. Options: 1. enable(1) -enable 2198 for voice 2. globalConfig(2) -global config: use the global con… |
| 1.3.6.1.4.1.2011.6.36.1.155.1.16 | ColumnhwDspDtmfBufferMode | read-write | current | Flag of the buffer mode for DTMF digits. Options: 1. enable(1) -enable the buffer function 2. disable(2) -disable the buffer function 3. adapt(3) -determined b… |
| 1.3.6.1.4.1.2011.6.36.1.156 | TablehwPreDigitMapConfigTable | not-accessible | current | This table is used to config local global digitmap for sip and h248 interface. The indexes of this table are hwPreDigitMapName, hwPreDigitMapSliceNo. |
| 1.3.6.1.4.1.2011.6.36.1.156.1 | RowhwPreDigitMapConfigEntry | not-accessible | current | This table is used to config local global digitmap for sip and h248 interface. The indexes of this entry are hwPreDigitMapName, hwPreDigitMapSliceNo. |
| 1.3.6.1.4.1.2011.6.36.1.156.1.1 | ColumnhwPreDigitMapName | not-accessible | current | Indicates the digitmap name. |
| 1.3.6.1.4.1.2011.6.36.1.156.1.2 | ColumnhwPreDigitMapSliceNo | not-accessible | current | Serial number for slice. High 8 bits for total number of slices, low 8 bits for sequence number of slices. |
| 1.3.6.1.4.1.2011.6.36.1.156.1.3 | ColumnhwPreDigitMapNewName | read-write | current | Indicates the new digitmap name. used for modifing digitmap name. |
| 1.3.6.1.4.1.2011.6.36.1.156.1.4 | ColumnhwPreDigitMapType | read-write | current | Indicate digit map type. For SIP it may be normal(1), emergency(2), scc(3), directCentrex(4), secondCentrex(5). For H248 it should only be normal(1). Options: … |
| 1.3.6.1.4.1.2011.6.36.1.156.1.5 | ColumnhwPreDigitMapBody | read-write | current | Indicate body of DigitMap, use by add,modify,delete operation. |
| 1.3.6.1.4.1.2011.6.36.1.156.1.6 | ColumnhwPreDigitMapRowStatus | read-write | current | Indicates the row status of the PreDigitMap. |
| 1.3.6.1.4.1.2011.6.36.1.156.1.7 | ColumnhwPreDigitMapTotalSlice | read-only | current | Indicates the total slice of the PreDigitMap. |
| 1.3.6.1.4.1.2011.6.36.1.156.1.8 | ColumnhwPreDigitMapProtocol | read-write | current | Indicates the digitmap protocol. Options: 1. h248(1) -h248 protocol 2. sip(2) -sip protocol |
| 1.3.6.1.4.1.2011.6.36.1.157 | TablehwVoipDynIPNameTable | not-accessible | current | This table is used to query the voip dynamic media and signal IP name. The indexes of this table are hwVoipDynIPNameType, hwVoipDynIPNameIndex. |
| 1.3.6.1.4.1.2011.6.36.1.157.1 | RowhwVoipDynIPNameEntry | not-accessible | current | This table is used to query the voip dynamic media and signal IP name. The indexes of this entry are hwVoipDynIPNameType, hwVoipDynIPNameIndex. |
| 1.3.6.1.4.1.2011.6.36.1.157.1.1 | ColumnhwVoipDynIPNameType | not-accessible | current | Indicates dynamic IP name type. Options: 1. mediaIP(1) -dynamic media IP name 2. signalIP(2) -dynamic signal IP name |
| 1.3.6.1.4.1.2011.6.36.1.157.1.2 | ColumnhwVoipDynIPNameIndex | not-accessible | current | Indicates dynamic IP name list index. |
| 1.3.6.1.4.1.2011.6.36.1.157.1.3 | ColumnhwVoipDynIPName | read-only | current | Indicates dynamic media IP name. |
| 1.3.6.1.4.1.2011.6.36.1.182 | NodehwDspOverloadResourceCfgTable | |||
| 1.3.6.1.4.1.2011.6.36.1.182.1 | ScalarhwDspResourceWorkMode | read-write | current | Indicates whether the AG restricts calls in case of insufficient DSP resource when many call raised. Options: 1. normal(1) -normal 2. priority(2) -priority Def… |
| 1.3.6.1.4.1.2011.6.36.1.182.2 | ScalarhwDspResourcethreshold1 | read-write | current | Indicates the normal call will use the max threshold of the whole DSP resource. The value of hwDspResourcethreshold1 must be smaller than or equal to the hwDsp… |
| 1.3.6.1.4.1.2011.6.36.1.182.3 | ScalarhwDspResourcethreshold2 | read-write | current | Indicates the max threshold of the whole DSP resource which used for the prior user. The value of hwDspResourcethreshold2 must be smaller than or equal to the … |
| 1.3.6.1.4.1.2011.6.36.1.182.4 | ScalarhwDspResourcethreshold3 | read-write | current | Indicates the max threshold of the whole DSP resource which used for the high prior user. Default: 100 Unit: 1/100 |
| 1.3.6.1.4.1.2011.6.36.1.183 | NodehwRfc2198ParaTable | |||
| 1.3.6.1.4.1.2011.6.36.1.183.1 | ScalarhwRfc2198ForVoice | read-write | current | Indicates the flag of voice using rfc2198. Only for H248 protocol. Options: 1. enable(1) -enable 2. disable(2) -disable Default: disable(2) |
| 1.3.6.1.4.1.2011.6.36.1.184 | NodehwRfc2198SmartParaTable | |||
| 1.3.6.1.4.1.2011.6.36.1.184.1 | ScalarhwFirstSectionUpThreshold | read-write | current | Indicates the up threshold for packet loss at the first section. Default: 5 Unit: 1/1000 |
| 1.3.6.1.4.1.2011.6.36.1.184.2 | ScalarhwSecondSectionUpThreshold | read-write | current | Indicates the up threshold for packet loss at the second section. Default: 30 Unit: 1/1000 |
| 1.3.6.1.4.1.2011.6.36.1.184.3 | ScalarhwThirdSectionUpThreshold | read-write | current | Indicates the up threshold for packet loss at the third section. Default: 50 Unit: 1/1000 |
| 1.3.6.1.4.1.2011.6.36.1.184.4 | ScalarhwFirstSectionRedundantNum | read-write | current | Indicates the redundant number for RFC2198 at the first section. Default: 0 |
| 1.3.6.1.4.1.2011.6.36.1.184.5 | ScalarhwSecondSectionRedundantNum | read-write | current | Indicates the redundant number for RFC2198 at the second section. Default: 1 |
| 1.3.6.1.4.1.2011.6.36.1.184.6 | ScalarhwThirdSectionRedundantNum | read-write | current | Indicates the redundant number for RFC2198 at the third section. Default: 2 |
| 1.3.6.1.4.1.2011.6.36.1.184.7 | ScalarhwFourthSectionRedundantNum | read-write | current | Indicates the redundant number for RFC2198 at the fourth section. Default: 3 |
| 1.3.6.1.4.1.2011.6.36.1.185 | TablehwTlsParaCfgTable | not-accessible | current | This table is used to set the tls attribute. The index of this table is hwTlsParaInterfaceId. |
| 1.3.6.1.4.1.2011.6.36.1.185.1 | RowhwTlsParaCfgEntry | not-accessible | current | This table is used to set the tls attribute. The index of this entry is hwTlsParaInterfaceId. |
| 1.3.6.1.4.1.2011.6.36.1.185.1.1 | ColumnhwTlsParaInterfaceId | not-accessible | current | Indicates the MG ID. The range of MG ID from 0 to 16777215 is for AG system, value of 33554431 is only for PBX system and the value input from 16777215 to 3355… |
| 1.3.6.1.4.1.2011.6.36.1.185.1.2 | ColumnhwTlsParaTlsVersion | read-write | current | Indicates the version of TLS. Options: 1. tlsv10(1) -TLS v1.0 2. tlsv11(2) -TLS v1.1 3. autoNegotiate(3) -auto negotiate Default: autoNegotiate(3) |
| 1.3.6.1.4.1.2011.6.36.1.185.1.3 | ColumnhwTlsParaAuthMode | read-write | current | Indicates the authentication mode of TLS. Options: 1. anonymous(1) -Anonymous 2. server(2) -Server 3. client(3) -Client 4. both(4) -Both Default: anonymous(1) |
| 1.3.6.1.4.1.2011.6.36.1.185.1.4 | ColumnhwTlsParaRootCA | read-write | current | Indicates the name of root certificate. |
| 1.3.6.1.4.1.2011.6.36.1.185.1.5 | ColumnhwTlsParaCert | read-write | current | Indicates the name of certificate. |
| 1.3.6.1.4.1.2011.6.36.1.185.1.6 | ColumnhwTlsParaKey | read-write | current | Indicates the name of key. |
| 1.3.6.1.4.1.2011.6.36.1.186 | TablehwTlsRunStateInfoTable | not-accessible | current | This table is used to display the tls running information. The index of this table is hwTlsRunStateInfoSessionID. |
| 1.3.6.1.4.1.2011.6.36.1.186.1 | RowhwTlsRunStateInfoEntry | not-accessible | current | This table is used to display the tls running information. The index of this entry is hwTlsRunStateInfoSessionID. |
| 1.3.6.1.4.1.2011.6.36.1.186.1.1 | ColumnhwTlsRunStateInfoSessionID | not-accessible | current | TLS session ID Constructed by Protocol-Type, Proxy-index, SIP-Interface-ID; Format:xyzzzzzz(Hex) a) x for Protocol-Type: SIP(0); b) y for Proxy-index: SIP Prox… |
| 1.3.6.1.4.1.2011.6.36.1.186.1.2 | ColumnhwTlsRunStateInfoVersion | read-only | current | Indicates the version of TLS. Options: 1. tlsv10(1) -TLS v1.0 2. tlsv11(2) -TLS v1.1 3. autoNegotiate(3) -auto negotiate |
| 1.3.6.1.4.1.2011.6.36.1.186.1.3 | ColumnhwTlsRunStateInfoAuthMode | read-only | current | Indicates the authentication mode of TLS. Options: 1. anonymous(1) -Anonymous 2. server(2) -Server 3. client(3) -Client 4. both(4) -Both Default: anonymous(1) |
| 1.3.6.1.4.1.2011.6.36.1.186.1.4 | ColumnhwTlsRunStateInfoRootCA | read-only | current | Indicates the name of root certificate. |
| 1.3.6.1.4.1.2011.6.36.1.186.1.5 | ColumnhwTlsRunStateInfoCert | read-only | current | Indicates the name of client certificate. |
| 1.3.6.1.4.1.2011.6.36.1.186.1.6 | ColumnhwTlsRunStateInfoKey | read-only | current | Indicates the name of client key. |
| 1.3.6.1.4.1.2011.6.36.1.186.1.7 | ColumnhwTlsRunStateInfoState | read-only | current | Indicates the state of handshake. Options: 1. idle(1) -Idle 2. handshaking(2) -Handshaking 3. handshakeSuccess(3) -HandshakeSuccess 4. handshakeFailure(4) -Han… |
| 1.3.6.1.4.1.2011.6.36.1.186.1.8 | ColumnhwTlsRunStateInfoCurrentCipher | read-only | current | Indicates the name of cipher. |
| 1.3.6.1.4.1.2011.6.36.1.187 | TablehwTlsCertificateTable | not-accessible | current | This table is used to config and query the certificates in system. The indexes of this table are hwTlsCertificateType and hwTlsCertificateIndex. |
| 1.3.6.1.4.1.2011.6.36.1.187.1 | RowhwTlsCertificateEntry | not-accessible | current | This table is used to config and query the certificates in system. The indexes of this entry are hwTlsCertificateType and hwTlsCertificateIndex. |
| 1.3.6.1.4.1.2011.6.36.1.187.1.1 | ColumnhwTlsCertificateType | not-accessible | current | Indicates the type of certificate. Options: 1. 0 -Root certificate 2. 1 -Certificate 3. 2 -Key |
| 1.3.6.1.4.1.2011.6.36.1.187.1.2 | ColumnhwTlsCertificateIndex | not-accessible | current | Indicates the index of certificate. |
| 1.3.6.1.4.1.2011.6.36.1.187.1.3 | ColumnhwTlsParaCertificateName | read-only | current | Indicates the name of certificate. |
| 1.3.6.1.4.1.2011.6.36.1.187.1.4 | ColumnhwTlsCertificateRowStatus | read-write | current | This is used to create new rows in this table, modify existing rows, and delete existing rows. |
| 1.3.6.1.4.1.2011.6.36.1.188 | TablehwIpTrkGrpFaxParaTable | not-accessible | current | This table is used to config the fax parameter of a IP truck group. The index of this table is hwIpTrkGrpFaxParaGrpName. |
| 1.3.6.1.4.1.2011.6.36.1.188.1 | RowhwIpTrkGrpFaxParaEntry | not-accessible | current | This table is used to config the fax parameter of a IP truck group. The index of this entry is hwIpTrkGrpFaxParaGrpName. |
| 1.3.6.1.4.1.2011.6.36.1.188.1.1 | ColumnhwIpTrkGrpFaxParaGrpName | not-accessible | current | Indicates the IP truck group name. |
| 1.3.6.1.4.1.2011.6.36.1.188.1.2 | ColumnhwIpTrkGrpFaxMode | read-write | current | Indicates the fax transmission mode. 1-Transparent transmission; 2-Auto-negotiation T.38; 3-V3 flow; 4-Stand-alone transparent transmission; 5-V5 flow; 6-Self-… |
| 1.3.6.1.4.1.2011.6.36.1.188.1.4 | ColumnhwIpTrkGrpFaxRedundancyFlag | read-write | current | Use fax redundancy parameter or not .1:enable,to use. 2:disable,not to use. This leaf only valid in sip transparent fax. |
| 1.3.6.1.4.1.2011.6.36.1.188.1.5 | ColumnhwIpTrkGrpFaxNegoMode | read-write | current | The negotiate mode of fax. Options: 1. negotiate(1) -negotiate 2. selfswitch(2) -do not negotiate |
| 1.3.6.1.4.1.2011.6.36.1.188.1.6 | ColumnhwIpTrkGrpFaxTransMode | read-write | current | Indicates the fax transmission mode. Options: 1. thoroughly(1) -use voice codec 2. t38(2) - use T.38 codec Default: thoroughly(1) |
| 1.3.6.1.4.1.2011.6.36.1.188.1.9 | ColumnhwIpTrkGrpFaxParaVbdCodec | read-write | current | Indicates the codec of VBD. Options: 1. g711A(1) -G.711A 2. g711U(2) -G.711U |
| 1.3.6.1.4.1.2011.6.36.1.188.1.10 | ColumnhwIpTrkGrpFaxParaVbdPtType | read-write | current | Indicates the payload type of VBD. Options: 1. static(1) -static payload type 2. dynamic(2) -dynamic payload type |
| 1.3.6.1.4.1.2011.6.36.1.188.1.12 | ColumnhwIpTrkGrpFaxVbdAttributeType | read-write | current | Indicate the format of session attribute lines when starting fax VBD Negotiation. Options: 1. v152(1) -v.152 format 2. chinatelecom(2) -chinatelecom format 3. … |
| 1.3.6.1.4.1.2011.6.36.1.188.1.13 | ColumnhwIpTrkGrpFaxRtpInterval | read-write | current | Indicates the default RTP packet time of DSP channel. Options: 1. packettime5ms(1) -5ms 2. packettime10ms(2) -10ms 3. packettime20ms(3) -20ms 4. packettime30ms… |
| 1.3.6.1.4.1.2011.6.36.1.189 | TablehwIpTrkGrpModemParaTable | not-accessible | current | This table is used to config the modem parameter of a IP truck group. The index of this table is hwIpTrkGrpModemParaGrpName. |
| 1.3.6.1.4.1.2011.6.36.1.189.1 | RowhwIpTrkGrpModemParaEntry | not-accessible | current | This table is used to config the modem parameter of a IP truck group. The index of this entry is hwIpTrkGrpModemParaGrpName. |
| 1.3.6.1.4.1.2011.6.36.1.189.1.1 | ColumnhwIpTrkGrpModemParaGrpName | not-accessible | current | Indicates the IP truck group name. |
| 1.3.6.1.4.1.2011.6.36.1.189.1.2 | ColumnhwIpTrkGrpModemMode | read-write | current | Indicates the modem transmission mode. 1-Negotiation mode; 2-Stand-alone mode. |
| 1.3.6.1.4.1.2011.6.36.1.189.1.3 | ColumnhwIpTrkGrpModemRedundancyFlag | read-write | current | Indicates the flag of using the modem redundancy parameter. 1-enable; 2-disable . |
| 1.3.6.1.4.1.2011.6.36.1.189.1.5 | ColumnhwIpTrkGrpModemNegoMode | read-write | current | The negotiate mode of fax. Options: 1. negotiate(1) -negotiate 2. selfswitch(2) -do not negotiate |
| 1.3.6.1.4.1.2011.6.36.1.189.1.6 | ColumnhwIpTrkGrpModemTransMode | read-write | current | Indicates the fax transmission mode. Options: 1. thoroughly(1) -thoroughly transmission 2. relay(2) -Relay mode Default: thoroughly(1) |
| 1.3.6.1.4.1.2011.6.36.1.189.1.9 | ColumnhwIpTrkGrpModemParaVbdCodec | read-write | current | Indicates the codec of VBD. Options: 1. g711A(1) -G.711A 2. g711U(2) -G.711U |
| 1.3.6.1.4.1.2011.6.36.1.189.1.10 | ColumnhwIpTrkGrpModemParaVbdPtType | read-write | current | Indicates the payload type of VBD. Options: 1. static(1) -static payload type 2. dynamic(2) -dynamic payload type |
| 1.3.6.1.4.1.2011.6.36.1.189.1.12 | ColumnhwIpTrkGrpModemVbdAttributeType | read-write | current | Indicate the format of session attribute lines when starting modem VBD Negotiation. Options: 1. v152(1) -V.152 2. chinatelecom(2) -china telecom 3. extchinatel… |
| 1.3.6.1.4.1.2011.6.36.1.189.1.13 | ColumnhwIpTrkGrpModemRtpInterval | read-write | current | Indicates the default RTP packet time of DSP channel. Options: 1. packettime5ms(1) -5ms 2. packettime10ms(2) -10ms 3. packettime20ms(3) -20ms 4. packettime30ms… |
| 1.3.6.1.4.1.2011.6.36.1.190 | TablehwIpTrkGrpRfc2833Table | not-accessible | current | This table is used to config the rfc2833 parameter of a IP truck group. The index of this table is hwIpTrkGrpRfc2833GrpName. |
| 1.3.6.1.4.1.2011.6.36.1.190.1 | RowhwIpTrkGrpRfc2833Entry | not-accessible | current | This table is used to config the rfc2833 parameter of a IP truck group. The index of this entry is hwIpTrkGrpRfc2833GrpName. |
| 1.3.6.1.4.1.2011.6.36.1.190.1.1 | ColumnhwIpTrkGrpRfc2833GrpName | not-accessible | current | Indicates the IP truck group name. |
| 1.3.6.1.4.1.2011.6.36.1.190.1.2 | ColumnhwIpTrkGrpRfc2833NegoMode | read-write | current | Indicates the start mode of the rfc2833. Options: 1. negoStart(1) -negotiate start 2. fixedStart(2) -fixed start 3. noInitiativeStart(3) -no initiative start |
| 1.3.6.1.4.1.2011.6.36.1.190.1.3 | ColumnhwIpTrkGrpRfc2833FaxModem | read-write | current | Indicates the flag of fax and modem event using rfc2833 parameter. Options: 1. enable(1) -enable 2. disable(2) -disable Default: enable(1) |
| 1.3.6.1.4.1.2011.6.36.1.190.1.4 | ColumnhwIpTrkGrpRfc2833FlashHook | read-write | current | Indicates the flag of flash hook event using rfc2833 parameter. Options: 1. enable(1) -enable 2. disable(2) -disable Default: disable(2) |
| 1.3.6.1.4.1.2011.6.36.1.190.1.5 | ColumnhwIpTrkGrpRfc2833Dtmf | read-write | current | Indicates the flag of dtmf using rfc2833 parameter. Options: 1. enable(1) -enable(1) 2. disable(2) -disable(2) Default: enable(1) |
| 1.3.6.1.4.1.2011.6.36.1.191 | TablehwIpTrkGrpRfc2198Table | not-accessible | current | This table is used to config the rfc2198 parameter of a IP truck group. The index of this table is hwIpTrkGrpRfc2198GrpName. |
| 1.3.6.1.4.1.2011.6.36.1.191.1 | RowhwIpTrkGrpRfc2198Entry | not-accessible | current | This table is used to config the rfc2198 parameter of a IP truck group. The index of this entry is hwIpTrkGrpRfc2198GrpName. |
| 1.3.6.1.4.1.2011.6.36.1.191.1.1 | ColumnhwIpTrkGrpRfc2198GrpName | not-accessible | current | Indicates the IP truck group name. |
| 1.3.6.1.4.1.2011.6.36.1.191.1.2 | ColumnhwIpTrkGrpRfc2198NegoMode | read-write | current | Indicates the start mode of the rfc2198. Options: 1. negoStart(1) -negotiate start 2. fixedStart(2) -fixed start 3. noInitiativeStart(3) -no initiative start |
| 1.3.6.1.4.1.2011.6.36.1.191.1.3 | ColumnhwIpTrkGrpRfc2198StartMode | read-write | current | Indicates the start mode of the rfc2198. Options: 1. smart2198(1) -smart start RFC2198 2. ordinary2198(2) -start RFC2198 ordinary |
| 1.3.6.1.4.1.2011.6.36.1.191.1.4 | ColumnhwIpTrkGrpRfc2198Rfc2833 | read-write | current | Indicates the flag of rfc2833 with using rfc2198. Options: 1. enable(1) -enable 2. disable(2) -disable Default: disable(2) |
| 1.3.6.1.4.1.2011.6.36.1.191.1.5 | ColumnhwIpTrkGrpRfc2198Vbd | read-write | current | Indicates the flag of the VBD using rfc2198. Options: 1. enable(1) -enable 2. disable(2) -disable |
| 1.3.6.1.4.1.2011.6.36.1.191.1.6 | ColumnhwIpTrkGrpRfc2198Voice | read-write | current | Indicates the flag of voice using rfc2198. Options: 1. enable(1) -enable 2. disable(2) -disable |
| 1.3.6.1.4.1.2011.6.36.1.192 | TablehwIpTrkGrpDtmfParaTable | not-accessible | current | This table is used to config the dtmf parameter of a IP truck group. The index of this table is hwIpTrkGrpDtmfGrpName. |
| 1.3.6.1.4.1.2011.6.36.1.192.1 | RowhwIpTrkGrpDtmfParaEntry | not-accessible | current | This table is used to config the dtmf parameter of a IP truck group. The index of this entry is hwIpTrkGrpDtmfGrpName. |
| 1.3.6.1.4.1.2011.6.36.1.192.1.1 | ColumnhwIpTrkGrpDtmfGrpName | not-accessible | current | Indicates the IP truck group name. |
| 1.3.6.1.4.1.2011.6.36.1.192.1.2 | ColumnhwIpTrkGrpDtmfTransMode | read-write | current | Indicates the transmission mode of DTMF. Options: 1. thoroughly(1) -transparent transmission 2. erase(2) -erase DTMF Default: thoroughly(1) |
| 1.3.6.1.4.1.2011.6.36.1.193 | TablehwDspResourceTypeTable | not-accessible | current | This table is used to config the DSP resource type. The index of this table is hwDspResourceTypeIndex. |
| 1.3.6.1.4.1.2011.6.36.1.193.1 | RowhwDspResourceTypeEntry | not-accessible | current | This table is used to config the DSP resource type. The index of this entry is hwDspResourceTypeIndex. |
| 1.3.6.1.4.1.2011.6.36.1.193.1.1 | ColumnhwDspResourceTypeIndex | not-accessible | current | Bits 31-26 (six bits): shelf index Bits 25-20 (six bits): slot index Bits 19-16 (four bits): subboard index Bits 15-0 (16 bits): chip index |
| 1.3.6.1.4.1.2011.6.36.1.193.1.2 | ColumnhwDspResourceTypeValue | read-write | current | Indicates the type of resource type. Options: 1. default(1) - default resource 2. instant(2) - instant conference resource 3. reserved(3) - reserved conference… |
| 1.3.6.1.4.1.2011.6.36.1.194 | TablehwDigitMapGroupConfigTable | not-accessible | current | This table is used to config the digitmap group. The index of this table is hwDigitMapGroupName. |
| 1.3.6.1.4.1.2011.6.36.1.194.1 | RowhwDigitMapGroupConfigEntry | not-accessible | current | This table is used to config the digitmap group. The index of this entry is hwDigitMapGroupName. |
| 1.3.6.1.4.1.2011.6.36.1.194.1.1 | ColumnhwDigitMapGroupName | not-accessible | current | Indicates the digitmap group name. |
| 1.3.6.1.4.1.2011.6.36.1.194.1.2 | ColumnhwDigitMapGroupNewName | read-write | current | Indicates the new name of digitmap group. |
| 1.3.6.1.4.1.2011.6.36.1.194.1.3 | ColumnhwDigitMapGroupReferDigitMapNameList | read-write | current | Indicates the digitmap name list in digitmap group. |
| 1.3.6.1.4.1.2011.6.36.1.194.1.4 | ColumnhwDigitMapGroupRowStatus | read-write | current | Indicates the row status of digitmap group. |
| 1.3.6.1.4.1.2011.6.36.1.196 | TablehwMgRingDefaultMgcParaTable | not-accessible | current | This table is used to config the default type for the common ring. The index of this table is hwMgRingDefaultMgcParaMgId. |
| 1.3.6.1.4.1.2011.6.36.1.196.1 | RowhwMgRingDefaultMgcParaEntry | not-accessible | current | This table is used to config the default type for the common ring. The index of this entry is hwMgRingDefaultMgcParaMgId. |
| 1.3.6.1.4.1.2011.6.36.1.196.1.1 | ColumnhwMgRingDefaultMgcParaMgId | not-accessible | current | Indicates the MG ID. |
| 1.3.6.1.4.1.2011.6.36.1.196.1.2 | ColumnhwMgRingDefaultMgcparaForRing | read-write | current | Indicates default peer para of the ring. Options: 255. Indicates resume system default config. |
| 1.3.6.1.4.1.2011.6.36.1.196.1.3 | ColumnhwMgRingDefaultMgcparaForMwi | read-write | current | Indicates default peer para of the mwi ring. Options: 255. Indicates resume system default config. |
| 1.3.6.1.4.1.2011.6.36.1.197 | TablehwIpTrkGrpTlsParaCfgTable | not-accessible | current | This table is used to set the tls attribute. The index of this table is hwIpTrkGrpTlsParaGrpName. |
| 1.3.6.1.4.1.2011.6.36.1.197.1 | RowhwIpTrkGrpTlsParaCfgEntry | not-accessible | current | This table is used to set the tls attribute. The index of this entry is hwIpTrkGrpTlsParaGrpName. |
| 1.3.6.1.4.1.2011.6.36.1.197.1.1 | ColumnhwIpTrkGrpTlsParaGrpName | not-accessible | current | Indicates the IP truck group name. |
| 1.3.6.1.4.1.2011.6.36.1.197.1.2 | ColumnhwIpTrkGrpTlsParaTlsVersion | read-write | current | Indicates the version of TLS. Options: 1. tlsv10(1) -TLS v1.0 2. tlsv11(2) -TLS v1.1 3. autoNegotiate(3) -auto negotiate Default: autoNegotiate(3) |
| 1.3.6.1.4.1.2011.6.36.1.197.1.3 | ColumnhwIpTrkGrpTlsParaAuthMode | read-write | current | Indicates the authentication mode of TLS. Options: 1. anonymous(1) -Anonymous 2. server(2) -Server 3. client(3) -Client 4. both(4) -Both Default: anonymous(1) |
| 1.3.6.1.4.1.2011.6.36.1.197.1.4 | ColumnhwIpTrkGrpTlsParaRootCA | read-write | current | Indicates the name of root certificate. |
| 1.3.6.1.4.1.2011.6.36.1.197.1.5 | ColumnhwIpTrkGrpTlsParaCert | read-write | current | Indicates the name of certificate. |
| 1.3.6.1.4.1.2011.6.36.1.197.1.6 | ColumnhwIpTrkGrpTlsParaKey | read-write | current | Indicates the name of key. |
| 1.3.6.1.4.1.2011.6.36.1.198 | TablehwMgRingDefaultRingParaTable | not-accessible | current | This table is used to set the default short ring type and AOCE ring type. The index of this table is hwMgRingDefaultRingparaMgId. |
| 1.3.6.1.4.1.2011.6.36.1.198.1 | RowhwMgRingDefaultRingParaEntry | not-accessible | current | This table is used to set the default short ring type and AOCE ring type. The index of this entry is hwMgRingDefaultRingparaMgId. |
| 1.3.6.1.4.1.2011.6.36.1.198.1.1 | ColumnhwMgRingDefaultRingparaMgId | not-accessible | current | Indicates the MG ID. |
| 1.3.6.1.4.1.2011.6.36.1.198.1.2 | ColumnhwMgShortRingType | read-write | current | Indicates the short ring type. Enumerated types: 1-Null, 2-Normal ring 1:4, 3-Special ring 1:2, 4-Special ring 0.4:0.2:0.4:4, 5-Long ring, 6-Special ring 1.2:2… |
| 1.3.6.1.4.1.2011.6.36.1.198.1.3 | ColumnhwMgAOCERingType | read-write | current | Indicates the AOCE ring type. Enumeration type: 1-Null, 2-Normal ring (FSK) 1:4, 3-Special ring (FSK) 1:2, 4-Special ring (FSK) 0.4:0.2:0.4:4, 5-Special ring (… |
| 1.3.6.1.4.1.2011.6.36.1.199 | TablehwVGWNumberChangeTable | not-accessible | current | This table is used to set the scheme od number change. The index of this table is hwVGWNumberChangeName. |
| 1.3.6.1.4.1.2011.6.36.1.199.1 | RowhwVGWNumberChangeEntry | not-accessible | current | This table is used to set the scheme od number change. The index of this entry is hwVGWNumberChangeName. |
| 1.3.6.1.4.1.2011.6.36.1.199.1.1 | ColumnhwVGWNumberChangeName | not-accessible | current | Indicates the name of number change. |
| 1.3.6.1.4.1.2011.6.36.1.199.1.2 | ColumnhwVGWNumberChangeType | read-write | current | Indicates the change type of number change. Options: 1. insert(1) - insert new number operation 2. replace(2) - replace number operation 3. delete(3) - delete … |
| 1.3.6.1.4.1.2011.6.36.1.199.1.3 | ColumnhwVGWNumberChangeStartPos | read-write | current | Indicates the change start position of source number. |
| 1.3.6.1.4.1.2011.6.36.1.199.1.4 | ColumnhwVGWNumberChangeNewNumber | read-write | current | Indicates the modify number of number change. |
| 1.3.6.1.4.1.2011.6.36.1.199.1.5 | ColumnhwVGWNumberChangeChangeLen | read-write | current | Indicates the modify length of number change,255 means to set this value invalid. |
| 1.3.6.1.4.1.2011.6.36.1.199.1.6 | ColumnhwVGWNumberChangeRowStatus | read-write | current | Indicates the row status. |
| 1.3.6.1.4.1.2011.6.36.1.199.1.7 | ColumnhwVGWNumberChangeTranslationRuleSetName | read-write | current | Indicates the translation rule set name of number change. |
| 1.3.6.1.4.1.2011.6.36.1.200 | NodehwSRTPParameterTable | |||
| 1.3.6.1.4.1.2011.6.36.1.200.1 | ScalarhwSrtpSwitch | read-write | current | Indicates the SRTP enable or disable. Options: 1. enable(1) -enable 2. disable(2) -disable Default: disable(2) |
| 1.3.6.1.4.1.2011.6.36.1.200.2 | ScalarhwSrtpMode | read-write | current | Indicates the Master SALT key achieve-mode: configuration or negotiation. Options: 1. configuration(1) - configuration 2. negotiation(2) - negotiation Default:… |
| 1.3.6.1.4.1.2011.6.36.1.200.3 | ScalarhwSrtpKey | read-write | current | Indicates the Master SALT key. |
| 1.3.6.1.4.1.2011.6.36.1.201 | TablehwTranslationRuleConfigTable | not-accessible | current | This table is used to set the translation rule. The index of this table is hwTranslationRuleName. |
| 1.3.6.1.4.1.2011.6.36.1.201.1 | RowhwTranslationRuleConfigEntry | not-accessible | current | This table is used to set the translation rule. The index of this entry is hwTranslationRuleName. |
| 1.3.6.1.4.1.2011.6.36.1.201.1.1 | ColumnhwTranslationRuleName | not-accessible | current | Indicates the name of translation rule. |
| 1.3.6.1.4.1.2011.6.36.1.201.1.2 | ColumnhwTranslationRuleMatchPattern | read-write | current | Indicates the match pattern of translation rule. |
| 1.3.6.1.4.1.2011.6.36.1.201.1.3 | ColumnhwTranslationRuleReplacePattern | read-write | current | Indicates the replace pattern of translation rule. |
| 1.3.6.1.4.1.2011.6.36.1.201.1.4 | ColumnhwTranslationRuleRowStatus | read-write | current | Indicates the row status. |
| 1.3.6.1.4.1.2011.6.36.1.202 | TablehwTranslationRuleSetTable | not-accessible | current | This table is used to config the translation rule set. The index of this table is hwTranslationRuleSetName. |
| 1.3.6.1.4.1.2011.6.36.1.202.1 | RowhwTranslationRuleSetEntry | not-accessible | current | This table is used to config the translation rule set. The index of this entry is hwTranslationRuleSetName. |
| 1.3.6.1.4.1.2011.6.36.1.202.1.1 | ColumnhwTranslationRuleSetName | not-accessible | current | Indicates the name of translation rule set. |
| 1.3.6.1.4.1.2011.6.36.1.202.1.2 | ColumnhwTranslationRuleList | read-write | current | Indicates the name and the priority of the translation rules in a translation rule set. |
| 1.3.6.1.4.1.2011.6.36.1.202.1.3 | ColumnhwTranslationRuleSetRowStatus | read-write | current | Indicates the row status of translation rule set. |
| 1.3.6.1.4.1.2011.6.36.1.203 | TablehwMgStreamQosConfigTable | not-accessible | current | This table is used to set the IP stream QOS of different VAG. The indexes of this table are hwMgStreamQosCfgProtoType and hwMgStreamQosCfgInterfaceId. |
| 1.3.6.1.4.1.2011.6.36.1.203.1 | RowhwMgStreamQosConfigEntry | not-accessible | current | This table is used to set the IP stream QOS of different VAG. The indexes of this entry are hwMgStreamQosCfgProtoType and hwMgStreamQosCfgInterfaceId. |
| 1.3.6.1.4.1.2011.6.36.1.203.1.1 | ColumnhwMgStreamQosCfgProtoType | not-accessible | current | Indicates the protocol of the interface to config IP stream QOS. Options: 1. iua(1) - the interface ID is IUA LinkNO. 2. h248(2) - the interface ID is VAG NO. … |
| 1.3.6.1.4.1.2011.6.36.1.203.1.2 | ColumnhwMgStreamQosCfgInterfaceId | not-accessible | current | Indicates the IP stream QOS interface ID. if Protocol Type is iua(1), this parameter for IUA LinkNo(0..15); if Protocol Type is h248(2), this parameter for H24… |
| 1.3.6.1.4.1.2011.6.36.1.203.1.3 | ColumnhwMgStreamQosCfgNormalMediaDscp | read-write | current | Indicates the QOS DSCP value of normal call media stream,255 means to set this value invalid. |
| 1.3.6.1.4.1.2011.6.36.1.203.1.4 | ColumnhwMgStreamQosCfgEmergencyMediaDscp | read-write | current | Indicates the QOS DSCP value of emergency call media stream,255 means to set this value invalid. |
| 1.3.6.1.4.1.2011.6.36.1.203.1.5 | ColumnhwMgStreamQosCfgNormalSignalingDscp | read-write | current | Indicates the QOS DSCP value of normal call signaling stream,255 means to set this value invalid. |
| 1.3.6.1.4.1.2011.6.36.1.203.1.6 | ColumnhwMgStreamQosCfgEmergencySignalingDscp | read-write | current | Indicates the QOS DSCP value of emergency call signaling stream,255 means to set this value invalid. |
| 1.3.6.1.4.1.2011.6.36.2 | NodehwIASVoipTraps | |||
| 1.3.6.1.4.1.2011.6.36.2.0 | NodehwIASVoipAlarmTraps | |||
| 1.3.6.1.4.1.2011.6.36.2.1 | NodehwIASVoipAlarmOids | |||
| 1.3.6.1.4.1.2011.6.36.9 | NodehwIASVoipComTrapsVbOids | |||
| 1.3.6.1.4.1.2011.6.36.9.1 | ScalarhwUserFrame | accessible-for-notify | current | The frame where mg user is configed. |
| 1.3.6.1.4.1.2011.6.36.9.2 | ScalarhwUserSlot | accessible-for-notify | current | The slot where mg user is configed. |
| 1.3.6.1.4.1.2011.6.36.9.3 | ScalarhwUserPort | accessible-for-notify | current | The port where mg user is configed. |
| 1.3.6.1.4.1.2011.6.36.9.4 | ScalarhwResDspFrame | accessible-for-notify | current | Indicate the frame NO. of a DSP resource board. |
| 1.3.6.1.4.1.2011.6.36.9.5 | ScalarhwResDspSlot | accessible-for-notify | current | Indicate the slot NO. of a DSP resource board. |
| 1.3.6.1.4.1.2011.6.36.9.6 | ScalarhwResDspSub | accessible-for-notify | current | The DSP sub-board NO. in a resource board. |
| 1.3.6.1.4.1.2011.6.36.9.7 | ScalarhwResDspChannel | accessible-for-notify | current | The DSP inner channel NO. in a subboard. |
| 1.3.6.1.4.1.2011.6.36.9.8 | ScalarhwRemoteIPAddr | accessible-for-notify | current | The remote ip address. |
| 1.3.6.1.4.1.2011.6.36.9.9 | ScalarhwStandbyProtocol | accessible-for-notify | current | The protocol in standby board. Options: 1. h248(1) -H.248 2. mgcp(2) -MGCP 3. sip(4) -SIP |
| 1.3.6.1.4.1.2011.6.36.9.10 | ScalarhwMgId | accessible-for-notify | current | The media gateway ID. |
| 1.3.6.1.4.1.2011.6.36.9.11 | ScalarhwRemotePort | accessible-for-notify | current | The remote port. |
| 1.3.6.1.4.1.2011.6.36.9.12 | ScalarhwRemoteIpAddr | accessible-for-notify | current | The remote ip address. |
| 1.3.6.1.4.1.2011.6.36.9.13 | ScalarhwAlarmLoopdelay | accessible-for-notify | current | The loop delay. |
| 1.3.6.1.4.1.2011.6.36.9.14 | ScalarhwAlarmPacketlost | accessible-for-notify | current | The packet loss rate. |
| 1.3.6.1.4.1.2011.6.36.9.15 | ScalarhwAlarmJitterbuffer | accessible-for-notify | current | The jitter-buffer. |
| 1.3.6.1.4.1.2011.6.36.10 | NodehwIASVoipComTraps | |||
| 1.3.6.1.4.1.2011.6.36.10.1 | NodehwIASVoipComCommonTraps | |||
| 1.3.6.1.4.1.2011.6.36.10.1.1 | NodehwIASVoipComResTraps | |||
| 1.3.6.1.4.1.2011.6.36.10.2 | NodehwIASVoipComAlarmTraps | |||
| 1.3.6.1.4.1.2011.6.36.10.2.1 | NodehwIASVoipComResAlarmTraps | |||
| 1.3.6.1.4.1.2011.6.36.10.2.1.0 | NodehwIASVoipComResAlarmTrapsPrefix | |||
| 1.3.6.1.4.1.2011.6.36.10.2.1.0.1 | NotificationhwIASVoipResUpwardbandwidthTrap | current | This notification indicates that the upstream-bandwidth is insufficient. | |
| 1.3.6.1.4.1.2011.6.36.10.2.1.0.2 | NotificationhwIASVoipResDspAbsentTrap | current | This notification indicates that the DSP resources insufficient. | |
| 1.3.6.1.4.1.2011.6.36.10.2.1.0.3 | NotificationhwIASVoipResDspQosExceedTrap | current | This notification indicates that the value of DSP QoS exceeds the threshold. | |
| 1.3.6.1.4.1.2011.6.36.10.2.1.0.4 | NotificationhwIASVoipResDspQosRestoreTrap | current | This notification indicates that the value of DSP QoS is normal. | |
| 1.3.6.1.4.1.2011.6.36.10.2.1.0.5 | NotificationhwIASVoipResJbThresholdExceedTrap | current | This notification indicates that the jitterbuffer exceeds the preset alarm threshold. | |
| 1.3.6.1.4.1.2011.6.36.10.2.1.0.6 | NotificationhwIASVoipResJbThresholdRestoreTrap | current | This notification indicates that the jitterbuffer is restored to below the present alarm threshold. | |
| 1.3.6.1.4.1.2011.6.36.10.2.1.0.7 | NotificationhwIASVoipResSysDSPAbsentTrap | current | This notification indicates that the DSP resources for voice services are insufficient. | |
| 1.3.6.1.4.1.2011.6.36.10.2.1.0.8 | NotificationhwIASVoipResSysDSPAbsentRestoreTrap | current | This notification indicates that the system recovers from insufficient DSP resources for voice services. | |
| 1.3.6.1.4.1.2011.6.36.10.2.2 | NodehwIASVoipComProtocolAlarmTraps | |||
| 1.3.6.1.4.1.2011.6.36.10.2.2.0 | NodehwIASVoipComProtocolAlarmTrapsPrefix | |||
| 1.3.6.1.4.1.2011.6.36.10.2.2.0.1 | NotificationhwIASVoipProtocolDiffTrap | current | This notification indicates that protocol in active Board and standby board are different. | |
| 1.3.6.1.4.1.2011.6.36.10.2.3 | NodehwIASVoipComVolcAlarmTraps | |||
| 1.3.6.1.4.1.2011.6.36.10.2.3.0 | NodehwIASVoipComVolcAlarmTrapsPrefix | |||
| 1.3.6.1.4.1.2011.6.36.10.2.3.0.1 | NotificationhwIASVoipVolcPowerDialerTrap | current | This notification indicates that user is in PowerDialer state. | |
| 1.3.6.1.4.1.2011.6.36.10.2.3.0.2 | NotificationhwIASVoipVolcPotsOverloadTrap | current | This notification indicates that POTS calling is overloaded. | |
| 1.3.6.1.4.1.2011.6.36.10.2.3.0.3 | NotificationhwIASVoipVolcIsdnOverloadTrap | current | This notification indicates that ISDN call service is overloaded. | |
| 1.3.6.1.4.1.2011.6.36.10.2.3.0.4 | NotificationhwIASVoipMgcOverloadTrap | current | This notification indicates that call events of the VAG exceed the call threshold set on the MGC. | |
| 1.3.6.1.4.1.2011.6.36.10.2.3.0.5 | NotificationhwIASVoipVolcPowerDialerRecoverTrap | current | This notification indicates that user is out of PowerDialer state. | |
| 1.3.6.1.4.1.2011.6.36.10.2.3.0.6 | NotificationhwIASVoipVolcPotsOverloadRecoverTrap | current | This notification indicates that POTS calling recovers from overload. | |
| 1.3.6.1.4.1.2011.6.36.10.2.3.0.7 | NotificationhwIASVoipVolcIsdnOverloadRecoverTrap | current | This notification indicates that ISDN calling recovers from overload. | |
| 1.3.6.1.4.1.2011.6.36.10.2.3.0.8 | NotificationhwIASVoipMgcOverloadRecoverTrap | current | This notification indicates that call events of the VAG recover to within the call threshold set on the MGC. |