HUAWEI-VOIP-H248-MIB
309 objects
This MIB module defines MIB objects that provide H248 management.
Imported Objects
| HUAWEI-MIB | huaweiUtility |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE private TimeTicks Unsigned32 |
| SNMPv2-TC | DisplayString RowStatus TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2011.6.36 | IdentityhwVoip | This MIB module defines MIB objects that provide H248 management. | ||
| 1.3.6.1.4.1.2011.6.36.1 | NodehwIASVoipObjects | |||
| 1.3.6.1.4.1.2011.6.36.1.1 | TablehwH248MedGwyConfigTable | not-accessible | current | This table is used to manage H248 media gateway. The index of this table is hwH248MedGwyId. |
| 1.3.6.1.4.1.2011.6.36.1.1.1 | RowhwH248MedGwyConfigEntry | not-accessible | current | This table is used to manage H248 media gateway. The index of this entry is hwH248MedGwyId. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.1 | ColumnhwH248MedGwyId | accessible-for-notify | current | Media Gateway ID. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.2 | ColumnhwH248MedGwyDomainName | read-write | current | Indicates the domain name of the MG, null means clear the value of this parameter. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.3 | ColumnhwH248MedGwyDesc | read-write | current | Indicates the interface description. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.4 | ColumnhwH248MedGwySigIPAddress1 | read-write | current | Indicates the signaling IP address of the MG. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.5 | ColumnhwH248MedGwyIPAddress2 | read-write | current | The second IP address that the Media Gateway Controller will use to communicate with the Media Gateway. The system does not support setting it now. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.6 | ColumnhwH248MedGwySigUDPPort | read-write | current | Signalling UDP port that the Media Gateway Controller will use to communicate with the Media Gateway. 65535 means this parameter is not configurated. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.7 | ColumnhwH248MedGwyProtocol | read-only | current | Type of the control protocol in use. Options: 1. h248(1) -H.248 |
| 1.3.6.1.4.1.2011.6.36.1.1.1.8 | ColumnhwH248MedGwyCodeType | read-write | current | Indicates the coding type. Options: 1. txt(1) -text 2. bin(2) -binary |
| 1.3.6.1.4.1.2011.6.36.1.1.1.9 | ColumnhwH248MedGwyTransMode | read-write | current | Indicates the transmission mode. Options: 1. noConfig(-1) -not configured 2. tcp(1) -tcp 3. udp(2) -udp 4. alfUdp(3) -udp with alf 5. sctp(4) -sctp |
| 1.3.6.1.4.1.2011.6.36.1.1.1.10 | ColumnhwH248MedGwyRegisterKey | read-write | current | Indicates the key that is registered with the MGC. The key cannot be modified, read, or written by the operator without authority, so the hwH248MedGwyRegisterK… |
| 1.3.6.1.4.1.2011.6.36.1.1.1.11 | ColumnhwH248MedGwyOperKey | read-only | current | Indicates the key for operating the MG. The hwH248MedGwyOperKey cannot be read. The functions of this key are as follows: 1) The hwH248MedGwyRegisterKey and hw… |
| 1.3.6.1.4.1.2011.6.36.1.1.1.12 | ColumnhwH248MedGwyOperKeyNew | read-write | current | Indicates the new operation key. The hwH248MedGwyOperKeyNew is a temporary variable, and cannot be read. If you query one hwH248MedGwyOperKeyNew, the system al… |
| 1.3.6.1.4.1.2011.6.36.1.1.1.13 | ColumnhwH248MedGwyAdminStatus | read-write | current | Administrative status for this media gateway control group. The default reason code relates to the status is as follows: reset shutdown force shutdown graceful… |
| 1.3.6.1.4.1.2011.6.36.1.1.1.14 | ColumnhwH248MedGwyOperStatus | read-only | current | Current operational status of the signaling link. Options: 1. up(1) -normal 2. localClosed(2) -local closed 3. fault(3) -fault 4. waitingAck(4) -wating for ack… |
| 1.3.6.1.4.1.2011.6.36.1.1.1.15 | ColumnhwH248MedGwyRowStatus | read-write | current | This is used to create new rows in this table, modify existing rows, and delete existing rows. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.16 | ColumnhwH248MedGwyLastChange | read-only | current | The value of sysUpTime at the time the associated link entered its current operational status. If the current status was entered prior to the last re-initializ… |
| 1.3.6.1.4.1.2011.6.36.1.1.1.17 | ColumnhwH248MedGwyProfile1 | read-write | obsolete | Indicates the name of the first H.248 profile of the MG (including / + version; version is a number). |
| 1.3.6.1.4.1.2011.6.36.1.1.1.18 | ColumnhwH248MedGwyProfile2 | read-write | obsolete | Indicates the name of the second H.248 profile of the MG (including / + version; version is a number). |
| 1.3.6.1.4.1.2011.6.36.1.1.1.19 | ColumnhwH248MedGwyProfile3 | read-write | obsolete | Indicates the name of the third H.248 profile of the MG (including / + version; version is a number). |
| 1.3.6.1.4.1.2011.6.36.1.1.1.20 | ColumnhwH248MedGwyProfileUsing | read-only | obsolete | Indicates the name of the profile that is currently in use. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.21 | ColumnhwH248MedGwyTopH248Version | read-only | obsolete | Indicates the latest H.248 version that is supported by the MG. In the P300, this parameter is read-only. Options: 1. v1(1) -version 1 2. v2(2) -version 2 3. v… |
| 1.3.6.1.4.1.2011.6.36.1.1.1.22 | ColumnhwH248MedGwyCurH248Version | read-only | current | Indicates the current H.248 version of the MG. Options: 1. v1(1) -version 1 2. v2(2) -version 2 3. v3(3) -version 3 |
| 1.3.6.1.4.1.2011.6.36.1.1.1.23 | ColumnhwH248MedGwyCurUsedDspNum | read-only | current | Indicates the count of currently occupied DSPs of the interface. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.24 | ColumnhwH248MedGwyAuthInitialKey | read-write | current | Indicates the authentication initial key. Default:0123456789ABCDEF |
| 1.3.6.1.4.1.2011.6.36.1.1.1.25 | ColumnhwH248MedGwyAuthMgId | read-write | current | Indicates the authentication MG ID. Default:AG |
| 1.3.6.1.4.1.2011.6.36.1.1.1.26 | ColumnhwH248MedGwyAuthAlgorithm | read-only | current | Indicates the authentication encryption algorithm. Options: 1. md5(1) -MD5 |
| 1.3.6.1.4.1.2011.6.36.1.1.1.27 | ColumnhwH248MedGwy2833Encrypt | read-write | current | Indicates the 2833 encryption key. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.28 | ColumnhwH248MedGwyCfgHeartBeatTimer | read-write | current | Indicates the configured timer of the initial heartbeat. Unit: second |
| 1.3.6.1.4.1.2011.6.36.1.1.1.29 | ColumnhwH248MedGwyCurHeartBeatTimer | read-only | current | Indicates the current timer of the initial heartbeat. The valid value range is 1..655, if the value is 0, the heartbeat is not started. Unit: second |
| 1.3.6.1.4.1.2011.6.36.1.1.1.30 | ColumnhwH248MedGwyCallHoldTimer | read-only | current | Indicates the timer of holding the call after the MG interface is interrupted. Unit: second |
| 1.3.6.1.4.1.2011.6.36.1.1.1.31 | ColumnhwH248MedGwyMediaIPAddress1 | read-write | current | Indicates the first media IP address of the MG. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.32 | ColumnhwH248MedGwyMIDType | read-write | current | Indicates the MID type of the MG message. Options: 1. ip4Address(1) -IP address 2. domainName(2) -domain name 3. deviceName(3) -device name |
| 1.3.6.1.4.1.2011.6.36.1.1.1.33 | ColumnhwH248MedGwyDeviceName | read-write | current | Indicates the name of the MG device. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.34 | ColumnhwH248MedGwyheartbeattimes | read-write | current | Indicates the count of heartbeat re-transmission. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.35 | ColumnhwH248MedGwyheartbeatretranstimer | read-write | current | Indicates the interval of heartbeat re-transmission. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.36 | ColumnhwH248MedGwyCurMIDType | read-only | current | Indicates the current MID type of the MG message. Options: 1. ip4Address(1) -IP address 2. domainName(2) -domain name 3. deviceName(3) -device name |
| 1.3.6.1.4.1.2011.6.36.1.1.1.37 | ColumnhwH248MedGwyCurDeviceName | read-only | current | Indicates the current name of the MG device. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.38 | ColumnhwH248MedGwyGracefulTimer | read-write | current | Indicates the graceful timer of the MG interface. This parameter is effective only when it is delivered with the shutdown graceful command. 0 means no time lim… |
| 1.3.6.1.4.1.2011.6.36.1.1.1.39 | ColumnhwH248MedGwyBeginNegotiationH248Version | read-write | current | Indicates the H.248 version at the beginning of the negotiation. 0:depend on profile 1:v1 2:v2 3:v3 |
| 1.3.6.1.4.1.2011.6.36.1.1.1.40 | ColumnhwH248MedGwyProfileIndex | read-write | current | Indicates the profile index configured for the MG. This parameter is effective only after the MG is reset. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.41 | ColumnhwH248MedGwyProfileIndexUsing | read-only | current | Indicates the profile index that is currently used by the MG. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.42 | ColumnhwH248ProfileParaNegotiationSupport | read-write | current | Indicates whether the MG supports the negotiated profile parameters. Options: 1. disable(1) -not support 2. enable(2) -support |
| 1.3.6.1.4.1.2011.6.36.1.1.1.43 | ColumnhwH248MgProfileCfgName | read-only | current | Indicates the configured name of the H.248 profile of the MG. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.44 | ColumnhwH248MgProfileNegoName | read-only | current | Indicates the negotiated name of the H.248 profile of the MG. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.45 | ColumnhwH248MedGwyMediaIPAddress2 | read-write | current | Indicates the second media IP of MG. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.46 | ColumnhwH248MedGwyOperReasonCode | read-write | current | Indicates the reason code of reset or shutdown interface.It's valid when set hwH248MedGwyAdminStatus to 4,5 or 6 at the same time. The leaf is optional,if not … |
| 1.3.6.1.4.1.2011.6.36.1.1.1.47 | ColumnhwH248MedGwySigIPAddrDhcpClientIndex | read-write | current | Dhcp Signal vlan id. The valid value range is 1..4093,if the value is -1, the static signal ip will be used. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.48 | ColumnhwH248MedGwyMediaIPAddrDhcpClientIndex | read-write | current | Dhcp Media vlan id. The valid value range is 1..4093,if the value is -1, the static media ip will be used. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.49 | ColumnhwH248MedGwyRestrans | read-write | current | Indicates whether the MG supports retrans. Options: 1. enable(1) -support 2. disable(2) -not support |
| 1.3.6.1.4.1.2011.6.36.1.1.1.50 | ColumnhwH248MedGwySigIPAddrName | read-write | current | Dynamic signal IP name. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.51 | ColumnhwH248MedGwyMediaIPAddrName | read-write | current | Dynamic media IP name. |
| 1.3.6.1.4.1.2011.6.36.1.1.1.52 | ColumnhwH248MedGwyKeepActiveFlag | read-write | current | The switch for transfer connect regular renovate. Options: 1. enable(1) -enable 2. disable(2) -disable Default: disable(2) |
| 1.3.6.1.4.1.2011.6.36.1.1.1.53 | ColumnhwH248MedGwyKeepActivePeriod | read-write | current | Indicates the configured period of transfer connect regular renovate. Unit: second Default:30 |
| 1.3.6.1.4.1.2011.6.36.1.2 | TablehwH248MedGwyCtrlTable | not-accessible | current | This table is used to config addresses of Media Gateway Controllers. The indexes of this table are hwH248MedGwyCtrlGatewayId, hwH248MedGwyCtrlIdx. |
| 1.3.6.1.4.1.2011.6.36.1.2.1 | RowhwH248MedGwyCtrlEntry | not-accessible | current | This table is used to config addresses of Media Gateway Controllers. The indexes of this entry are hwH248MedGwyCtrlGatewayId, hwH248MedGwyCtrlIdx. |
| 1.3.6.1.4.1.2011.6.36.1.2.1.1 | ColumnhwH248MedGwyCtrlGatewayId | not-accessible | current | Indicates the MG ID. |
| 1.3.6.1.4.1.2011.6.36.1.2.1.2 | ColumnhwH248MedGwyCtrlIdx | not-accessible | current | Indicates the MGC index. |
| 1.3.6.1.4.1.2011.6.36.1.2.1.3 | ColumnhwH248MedGwyCtrlIPAddress | read-write | current | The IP address of the Media Gateway Controller. The value 255.255.255.255 is returned if the entry is invalid. |
| 1.3.6.1.4.1.2011.6.36.1.2.1.4 | ColumnhwH248MedGwyCtrlDnsName | read-write | current | Indicates the DNS name of the MGC. |
| 1.3.6.1.4.1.2011.6.36.1.2.1.5 | ColumnhwH248MedGwyCtrlDnsIp | read-only | current | Indicates the IP address that is obtained through the MGC domain name. DEFVAL { false } |
| 1.3.6.1.4.1.2011.6.36.1.2.1.6 | ColumnhwH248MedGwyCtrlPort | read-write | current | UDP port of the Media Gateway Controller. The value 65535 is returned if the entry is invalid. |
| 1.3.6.1.4.1.2011.6.36.1.2.1.7 | ColumnhwH248MedGwyCtrlAdminStatus | read-write | current | Indicates to set the MGC as the active MGC. Options: 1. active(1) -active state |
| 1.3.6.1.4.1.2011.6.36.1.2.1.8 | ColumnhwH248MedGwyCtrlOperStatus | read-only | current | Status of the Media Gateway Controller (and/or) its transportLink. Options: 1. up(1) -normal 2. down(2) -fault 3. standby(3) -standby |
| 1.3.6.1.4.1.2011.6.36.1.2.1.9 | ColumnhwH248MedGwyCtrlRowStatus | read-write | current | Indicates the row status. |
| 1.3.6.1.4.1.2011.6.36.1.2.1.10 | ColumnhwH248MedGwyCtrlLastChange | read-only | current | The value of sysUpTime at the time the associated link entered its current operational status. If the current status was entered prior to the last re-initializ… |
| 1.3.6.1.4.1.2011.6.36.1.2.1.11 | ColumnhwH248MedGwyCtrlIPAddress2 | read-write | current | The IP address of the Media Gateway Controller for SCTP dual homing. The value 255.255.255.255 is returned if the entry is invalid. |
| 1.3.6.1.4.1.2011.6.36.1.3 | TablehwMgPhyTerminationCfgTable | not-accessible | current | This table is used to config the physical termination of the MG. The index of this table is hwMgPhyTerminationIndex. |
| 1.3.6.1.4.1.2011.6.36.1.3.1 | RowhwMgPhyTerminationCfgEntry | not-accessible | current | This table is used to config the physical termination of the MG. The index of this entry is hwMgPhyTerminationIndex. |
| 1.3.6.1.4.1.2011.6.36.1.3.1.1 | ColumnhwMgPhyTerminationIndex | not-accessible | current | Indicates the shelf/slot/port. |
| 1.3.6.1.4.1.2011.6.36.1.3.1.2 | ColumnhwMgPhyTerminationMgId | read-create | current | Indicates the MG ID. |
| 1.3.6.1.4.1.2011.6.36.1.3.1.3 | ColumnhwMgPhyTerminationID | read-create | current | Indicates the termination ID. |
| 1.3.6.1.4.1.2011.6.36.1.3.1.4 | ColumnhwMgPhyTerminationTelNo | read-create | current | Indicates the telephone number. |
| 1.3.6.1.4.1.2011.6.36.1.3.1.5 | ColumnhwMgPhyTerminationSrvState | read-only | current | Indicates the service status. Options: 1. serviceStopLocal(1) -stop local service 2. serviceStopRemote(2) -stop remote service 3. serviceStopAuto(3) -stop serv… |
| 1.3.6.1.4.1.2011.6.36.1.3.1.6 | ColumnhwMgPhyTerminationOperate | read-write | current | Indicates the service operation. Options: 1. stop(1) -stop service 2. start(2) -start service |
| 1.3.6.1.4.1.2011.6.36.1.3.1.7 | ColumnhwMgPhyTerminationRowStatus | read-write | current | Indicates the row status. |
| 1.3.6.1.4.1.2011.6.36.1.3.1.8 | ColumnhwMgPhyTerminationContexID | read-only | current | Indicates the context ID of the termination. |
| 1.3.6.1.4.1.2011.6.36.1.3.1.9 | ColumnhwMgPhyTerminationLayerFlag | read-only | current | Indicates the layering flag. Currently, only the value nolayer(1) is supported. Options: 1. nolayer(1) -not to layer 2. layer(2) -to layer |
| 1.3.6.1.4.1.2011.6.36.1.3.1.10 | ColumnhwMgPhyTerminationLastChange | read-only | current | Indicates the service status changing time. |
| 1.3.6.1.4.1.2011.6.36.1.3.1.11 | ColumnhwMgPhyTerminationPriorityFlag | read-write | current | Indicates the priority of the termination. Options: 1. cat1(1) -cat1 2. cat2(2) -cat2 3. cat3(3) -cat3 |
| 1.3.6.1.4.1.2011.6.36.1.3.1.12 | ColumnhwMgPhyTerminationSrvAlarmState | read-only | current | Indicates the alarm state of service port. Options: 1. no(1) -has no alarm 2. yes(2) -has alarm |
| 1.3.6.1.4.1.2011.6.36.1.3.1.13 | ColumnhwMgPhyTerminationSrvAlarmType | read-only | current | Indicates the alarm type of service port. Options: 1. portFailure(1) -port failure 2. vagInterfaceInterrupt(2) -VAG Interrupt 3. noDsp(3) -no DSP resource alar… |
| 1.3.6.1.4.1.2011.6.36.1.4 | TablehwMgPhyTerminationOperTable | not-accessible | current | This table is used to query the port status of the physical termination of the MG. The index of this table is hwMgPhyTermIndex. |
| 1.3.6.1.4.1.2011.6.36.1.4.1 | RowhwMgPhyTerminationOperEntry | not-accessible | current | This table is used to query the port status of the physical termination of the MG. The index of this entry is hwMgPhyTermIndex. |
| 1.3.6.1.4.1.2011.6.36.1.4.1.1 | ColumnhwMgPhyTermIndex | not-accessible | current | Indicates the shelf/slot/port. |
| 1.3.6.1.4.1.2011.6.36.1.4.1.2 | ColumnhwMgPhyTerminationPortState | read-only | current | Indicates the physical status of the port. Options: 1. idle(1) -idle 2. fault(2) -faulty 3. test(3) -test 4. lock(4) -locked 5. busy(5) -busy 6. localLoop(6) -… |
| 1.3.6.1.4.1.2011.6.36.1.4.1.3 | ColumnhwMgPhyTerminationSrvType | read-only | current | Indicates the service type of the port. Options: 1. normal(1)-instant service 2. innerSpc(2) -inner SPC 3. v5spc(3) -V5 SPC 4. v5pre(4) -V5 pre-connection 5. p… |
| 1.3.6.1.4.1.2011.6.36.1.4.1.4 | ColumnhwMgPhyTerminationAdminStatus | read-write | current | Indicates the maintenance operation of the port. Options: 1. reset(1) -reset 2. localloop(2) -local loopback 3. remoteloop(3) -remote loopback 4. cancelloop(4)… |
| 1.3.6.1.4.1.2011.6.36.1.4.1.5 | ColumnhwMgPhyTerminationStateChange | read-only | current | Indicates the physical status changing time of the port. |
| 1.3.6.1.4.1.2011.6.36.1.4.1.6 | ColumnhwMgPhyTerminationConfigState | read-only | current | Indicates the configured subscriber type. Options: 1. configedMgUser(1) -configured MG subscriber 2. configedV5User(2) -configured V5 subscriber 3. notConfiged… |
| 1.3.6.1.4.1.2011.6.36.1.4.1.7 | ColumnhwMgPhyTerminationOperOperate | read-write | current | Indicates the service operation. Options: 1. stop(1) -stop service 2. start(2) -start service |
| 1.3.6.1.4.1.2011.6.36.1.4.1.8 | ColumnhwMgPhyTerminationMaxCOBTime | read-write | current | The longest time of out of service gracefully. Unit:minute |
| 1.3.6.1.4.1.2011.6.36.1.4.1.9 | ColumnhwMgPhyTerminationOnExpire | read-write | current | The disposal method when the port get out of service gracefully. Options: 1. forced(1) -force to stop service 2. cancel(2) -cancel operation |
| 1.3.6.1.4.1.2011.6.36.1.4.1.10 | ColumnhwMgPhyTerminationUpTimeSinceLastRTS | read-only | current | The time since PSTN port get in service latest |
| 1.3.6.1.4.1.2011.6.36.1.4.1.11 | ColumnhwMgPhyTerminationEndServiceLastTime | read-only | current | Remanent time before the timer overtime |
| 1.3.6.1.4.1.2011.6.36.1.4.1.12 | ColumnhwMgPhyTerminationEndServiceMode | read-write | current | Endservice mode. 1-Immediate, 2-Graceful. |
| 1.3.6.1.4.1.2011.6.36.1.5 | TablehwMgEphemeralTerminationTable | not-accessible | current | This table is used to config the virtual termination configuration of the MG. The indexes of this table are hwMgEphemeralTerminationMgId, hwMgEphemeralTerminat… |
| 1.3.6.1.4.1.2011.6.36.1.5.1 | RowhwMgEphemeralTerminationEntry | not-accessible | current | This table is used to config the virtual termination configuration of the MG. The indexes of this entry are hwMgEphemeralTerminationMgId, hwMgEphemeralTerminat… |
| 1.3.6.1.4.1.2011.6.36.1.5.1.1 | ColumnhwMgEphemeralTerminationMgId | not-accessible | current | Indicates the MG ID. |
| 1.3.6.1.4.1.2011.6.36.1.5.1.2 | ColumnhwMgEphemeralTerminationID | not-accessible | current | Indicates the virtual termination ID. |
| 1.3.6.1.4.1.2011.6.36.1.5.1.3 | ColumnhwMgEphemeralTerminationPacketTime | read-only | current | Indicates the packetizing time. Unit: millisecond. |
| 1.3.6.1.4.1.2011.6.36.1.5.1.4 | ColumnhwMgEphemeralTerminationVAD | read-only | current | Indicates voice activity detection. Options: 1. true(1) -enable VAD 2. false(2) -disable VAD |
| 1.3.6.1.4.1.2011.6.36.1.5.1.5 | ColumnhwMgEphemeralTerminationEC | read-only | current | Indicates echo cancel. Options: 1. true(1) -enable EC 2. false(2) -disable EC |
| 1.3.6.1.4.1.2011.6.36.1.5.1.6 | ColumnhwMgEphemeralTerminationJitBuffer | read-only | current | Indicates the value of JitBuffer. Unit: second. |
| 1.3.6.1.4.1.2011.6.36.1.5.1.7 | ColumnhwMgEphemeralTerminationTransGain | read-only | current | Indicates the transmit gain. Unit: dB. |
| 1.3.6.1.4.1.2011.6.36.1.5.1.8 | ColumnhwMgEphemeralTerminationRecvGain | read-only | current | Indicates the receive gain. Unit: dB. |
| 1.3.6.1.4.1.2011.6.36.1.5.1.9 | ColumnhwMgEphemeralTerminationCodeC | read-only | current | Indicates the enumerated definition of the VoiceCode. Note that several items in the enumerated definition are not consecutive. In the definition above, acG723… |
| 1.3.6.1.4.1.2011.6.36.1.5.1.10 | ColumnhwMgEphemeralTerminationLocalIPAddr | read-only | current | Indicates the local IP address. |
| 1.3.6.1.4.1.2011.6.36.1.5.1.11 | ColumnhwMgEphemeralTerminationLocalPort | read-only | current | Indicates the local RTP port. |
| 1.3.6.1.4.1.2011.6.36.1.5.1.12 | ColumnhwMgEphemeralTerminationPeerIPAddr | read-only | current | Indicates the peer IP address. |
| 1.3.6.1.4.1.2011.6.36.1.5.1.13 | ColumnhwMgEphemeralTerminationPeerPort | read-only | current | Indicates the peer RTP port. |
| 1.3.6.1.4.1.2011.6.36.1.5.1.14 | ColumnhwMgEphemeralTerminationPlace | read-only | current | Indicates the DSP channel (shelf/slot/subboard/channel index) of the virtual terminal of the MG. Bits 31-26 (six bits): shelf index Bits 25-20 (six bits): slot… |
| 1.3.6.1.4.1.2011.6.36.1.5.1.15 | ColumnhwMgEphemeralTerminationContexID | read-only | current | Indicates the context ID. |
| 1.3.6.1.4.1.2011.6.36.1.6 | TablehwMgContexTable | not-accessible | current | This table is used to config the context of the MG. The indexes of this table are hwMgContexMgId, hwMgContexlID. |
| 1.3.6.1.4.1.2011.6.36.1.6.1 | RowhwMgContexEntry | not-accessible | current | This table is used to config the context of the MG. The indexes of this entry are hwMgContexMgId, hwMgContexlID. |
| 1.3.6.1.4.1.2011.6.36.1.6.1.1 | ColumnhwMgContexMgId | not-accessible | current | Indicates the MG ID. |
| 1.3.6.1.4.1.2011.6.36.1.6.1.2 | ColumnhwMgContexlID | not-accessible | current | Indicates the context ID. |
| 1.3.6.1.4.1.2011.6.36.1.6.1.3 | ColumnhwMgTerminationID1 | read-only | current | Indicates the physical termination ID. |
| 1.3.6.1.4.1.2011.6.36.1.6.1.4 | ColumnhwMgTerminationID2 | read-only | current | Indicates the virtual termination ID. |
| 1.3.6.1.4.1.2011.6.36.1.17 | TablehwH248ParaTable | not-accessible | current | This table is used to config the H.248 parameter. The index of this table is hwH248ParaMgId. |
| 1.3.6.1.4.1.2011.6.36.1.17.1 | RowhwH248ParaEntry | not-accessible | current | This table is used to config the H.248 parameter. The index of this entry is hwH248ParaMgId. |
| 1.3.6.1.4.1.2011.6.36.1.17.1.1 | ColumnhwH248ParaMgId | not-accessible | current | Indicates the MG ID. |
| 1.3.6.1.4.1.2011.6.36.1.17.1.2 | ColumnhwH248ParaTransReliable | read-write | current | Indicates the transaction reliability. The transaction reliability queue and the re-transmission timer are initialized when the protocol is initialized. Theref… |
| 1.3.6.1.4.1.2011.6.36.1.17.1.3 | ColumnhwH248ParaLongTimer | read-write | current | Indicates the length of the long timer. This parameter is a concept in the transaction reliability of the H.248 protocol stack. The protocol recommends a value… |
| 1.3.6.1.4.1.2011.6.36.1.17.1.4 | ColumnhwH248ParaMaxRetransTimer | read-write | current | Indicates the maximum length of the re-transmission timer. This parameter is a concept in the transaction reliability of the H.248 protocol stack. The protocol… |
| 1.3.6.1.4.1.2011.6.36.1.17.1.5 | ColumnhwH248ParaMinRetransTimer | read-write | current | Indicates the minimum length of the re-transmission timer. This parameter is a concept in the transaction reliability of the H.248 protocol stack. The protocol… |
| 1.3.6.1.4.1.2011.6.36.1.17.1.6 | ColumnhwH248ParaMgProvRespTimer | read-write | current | Indicates the length of the timer for provisional responses. By default, it is 8000 ms. Unit: millisecond. |
| 1.3.6.1.4.1.2011.6.36.1.17.1.7 | ColumnhwH248ParaMaxRetrans | read-write | current | Indicates the maximum count of re-transmission. This parameter is a concept in the transaction reliability of the H.248 protocol stack. The value can be set dy… |
| 1.3.6.1.4.1.2011.6.36.1.17.1.8 | ColumnhwH248ParaSecurity | read-write | current | Indicates the authorization type. Options: 1. noah(1) -no authorization 2. md5(2) -MD5 3. sha1(3) -SHA1 The configuration will no longer take effect, and the v… |
| 1.3.6.1.4.1.2011.6.36.1.17.1.9 | ColumnhwH248ParaSdpEncodeType | read-write | current | Indicates the SDP encapsulation type. Options: 1. text(1) -text 2. hex(2) -hex |
| 1.3.6.1.4.1.2011.6.36.1.17.1.10 | ColumnhwH248ParaResponseAckCtrl | read-write | current | Indicates the switch of the three-way handshake signal. Options: 1. false(1) -disable three-way handshake 2. true(2) -enable three-way handshake |
| 1.3.6.1.4.1.2011.6.36.1.17.1.11 | ColumnhwH248ParaRetransMode | read-write | current | Indicates the retransmission mode. Options: 1. auto(1) -auto 2. fixed(2) -fixed |
| 1.3.6.1.4.1.2011.6.36.1.17.1.12 | ColumnhwH248ParaRetransTimer | read-write | current | Indicates the fixed re-transmission interval (this parameter is effective when the re-transmission mode is the fixed mode; by default, it is 2000). |
| 1.3.6.1.4.1.2011.6.36.1.17.1.13 | ColumnhwH248ParaTMax | read-write | current | Indicates the re-transmission length of the H.248 protocol stack (by default, it is 25000). |
| 1.3.6.1.4.1.2011.6.36.1.17.1.14 | ColumnhwH248ParaRetransfailoption | read-only | current | Indicates the retransmission failure option of the H.248 protocol stack. Options: 1. times(1) -times 2. tMax(2) -max time |
| 1.3.6.1.4.1.2011.6.36.1.17.1.15 | ColumnhwH248ParaFormatoption | read-write | current | Indicates the message format of the H.248 protocol stack. Options: 1. short(1) -short format 2. long(2) -long format Default: short(1) |
| 1.3.6.1.4.1.2011.6.36.1.17.1.16 | ColumnhwH248ParaMTU | read-write | current | Indicates the value of the maximum transmission unit of the H.248 protocol stack. Default: 1500 |
| 1.3.6.1.4.1.2011.6.36.1.17.1.17 | ColumnhwH248ParaMessagesegmentation | read-write | current | Indicates the message format of the H.248 protocol stack. Options: 1. support(1) -support format message 2. notsupport(2) -not support format message Default: … |
| 1.3.6.1.4.1.2011.6.36.1.17.1.18 | ColumnhwH248ParaMgcProvRespTimer | read-write | current | Indicates the length of MGC provisional response timer. Unit: millisecond |
| 1.3.6.1.4.1.2011.6.36.1.17.1.19 | ColumnhwH248ParaMgOriginatedPendingLimit | read-write | current | Indicates the max times of MG sends provisional response. |
| 1.3.6.1.4.1.2011.6.36.1.17.1.20 | ColumnhwH248ParaMgcOriginatedPendingLimit | read-write | current | Indicates the max times of MGC sends provisional response. |
| 1.3.6.1.4.1.2011.6.36.1.23 | TablehwH248DigitmapTable | not-accessible | current | This table is used to config the inner digitmap configuration. The index of this table is hwH248DigitmapMgId. |
| 1.3.6.1.4.1.2011.6.36.1.23.1 | RowhwH248DigitmapEntry | not-accessible | current | This table is used to config the inner digitmap configuration. The index of this entry is hwH248DigitmapMgId. |
| 1.3.6.1.4.1.2011.6.36.1.23.1.1 | ColumnhwH248DigitmapMgId | not-accessible | current | Indicates the MG interface ID. |
| 1.3.6.1.4.1.2011.6.36.1.23.1.2 | ColumnhwH248DigitmapInner | read-write | current | Indicates the inner call digitmap. |
| 1.3.6.1.4.1.2011.6.36.1.23.1.3 | ColumnhwH248DigitmapEmergency | read-write | current | Indicates the emergency channel digitmap. |
| 1.3.6.1.4.1.2011.6.36.1.23.1.4 | ColumnhwH248DigitmapDualdial | read-write | current | Indicates the automatic re-dial digitmap. |
| 1.3.6.1.4.1.2011.6.36.1.23.1.5 | ColumnhwH248DigitmapOverLoadUrgent | read-write | current | Indicates the emergency call digitmap in case of overload or insufficient bandwidth. |
| 1.3.6.1.4.1.2011.6.36.1.24 | TablehwStandaloneParaTable | not-accessible | current | This table is used to config the stand-alone parameter. The index of this table is hwStandaloneParaMgId. |
| 1.3.6.1.4.1.2011.6.36.1.24.1 | RowhwStandaloneParaEntry | not-accessible | current | This table is used to config the stand-alone parameter. The index of this entry is hwStandaloneParaMgId. |
| 1.3.6.1.4.1.2011.6.36.1.24.1.1 | ColumnhwStandaloneParaMgId | not-accessible | current | Indicates the MG interface ID. |
| 1.3.6.1.4.1.2011.6.36.1.24.1.2 | ColumnhwStandAloneDialTone | read-write | current | Indicates the duration of the dial tone. Unit: second |
| 1.3.6.1.4.1.2011.6.36.1.24.1.3 | ColumnhwStandAloneRing | read-write | current | Indicates the duration of the ring. Unit: second |
| 1.3.6.1.4.1.2011.6.36.1.24.1.4 | ColumnhwStandAloneBusyTone | read-write | current | Indicates the duration of the busy tone. Unit: second |
| 1.3.6.1.4.1.2011.6.36.1.28 | TablehwH248MgSoftParameterTable | not-accessible | current | This table is to indicates the MG software parameter. The index of this table is hwH248MgInterfaceIndex. |
| 1.3.6.1.4.1.2011.6.36.1.28.1 | RowhwH248MgSoftParameterEntry | not-accessible | current | This table is to indicates the MG software parameter. The index of this entry is hwH248MgInterfaceIndex. |
| 1.3.6.1.4.1.2011.6.36.1.28.1.1 | ColumnhwH248MgInterfaceIndex | not-accessible | current | Indicates the MG interface index. |
| 1.3.6.1.4.1.2011.6.36.1.28.1.2 | ColumnhwH248MgSoftParameter0 | read-write | deprecated | Parameter name index 0. It indicates whether the terminal ID of the MG interface is layered. In the P300, the values of 1 and 2 are unavailable. Options: 1. ye… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.3 | ColumnhwH248MgSoftParameter1 | read-write | deprecated | Parameter name index 1. It indicates whether the ongoing calls are maintained after MG is disconnected from MGC. (It is unavailable in the VSPV1R2.) Options: 1… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.4 | ColumnhwH248MgSoftParameter2 | read-write | current | Parameter name index 2. It indicates whether the MG interface supports multiple homing. It is unavailable in the VSPV1R2. Options: 1. no(1) -not support multip… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.5 | ColumnhwH248MgSoftParameter3 | read-write | deprecated | Parameter name index 3. It indicates the MG interface interruption detecting mode. It is unavailable in the P300. Options: 1. heartbeat(1) -heartbeat 2. messag… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.6 | ColumnhwH248MgSoftParameter4 | read-write | current | Parameter name index 4. It indicates whether the wildcard is used in registration. Options: 1. yes(1) -use wildcard in registration 2. no(2) -do not use wildca… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.7 | ColumnhwH248MgSoftParameter5 | read-write | deprecated | Parameter name index 5. It indicates whether the port fault and auto-block is reported to the MGC. Options: 1. yes(1) -the port fault and auto-block is reporte… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.8 | ColumnhwH248MgSoftParameter6 | read-write | current | Parameter name index 6. It indicates whether authentication is supported. Options: 1. yes(1) -support authentication 2. no(2) -not support authentication Defau… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.9 | ColumnhwH248MgSoftParameter7 | read-write | current | Parameter name index 7. It indicates whether the security header is supported. Options: 1. yes(1) -support the security header 2. no(2) -not support the securi… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.10 | ColumnhwH248MgSoftParameter8 | read-write | deprecated | Parameter name index 8. It indicates the maximum count of DSPs supported by the VAG. It is unavailable in the P300. |
| 1.3.6.1.4.1.2011.6.36.1.28.1.11 | ColumnhwH248MgSoftParameter9 | read-write | deprecated | Parameter name index 9. It indicates whether overload control is supported. It is unavailable in the P300. Options: 1. yes(1) -support overload control 2. no(2… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.12 | ColumnhwH248MgSoftParameter10 | read-write | deprecated | Parameter name index 10. It indicates whether the SDP contains the o=,s=,t= row. It is unavailable in the VSPV1R2. Options: 1. yes(1) -SDP contain the o=,s=,t=… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.13 | ColumnhwH248MgSoftParameter11 | read-write | current | Parameter name index 11. It indicates the stand-alone flag. Options: 1. none(1) -not support stand alone 2. inner(2) -support inner call 3. emergency(3) -suppo… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.14 | ColumnhwH248MgSoftParameter12 | read-write | deprecated | Parameter name index 12. It indicates the stand-alone interruption flag. It is unavailable in the VSPV1R2. Options: 1. no(1) -no 2. yes(2) -yes Default: no(1) |
| 1.3.6.1.4.1.2011.6.36.1.28.1.15 | ColumnhwH248MgSoftParameter13 | read-write | current | Parameter name index 13. It indicates the DMM match mode. Options: 1. min(1) -shortest 2. max(2) -longest 3. auto(3) -protocol define 4. autoadapt(4) -auto ada… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.16 | ColumnhwH248MgSoftParameter14 | read-write | deprecated | Parameter name index 14. It indicates the value of the maximum transmission unit. Options: 1. min(1) -min 2. max(5000) -max |
| 1.3.6.1.4.1.2011.6.36.1.28.1.17 | ColumnhwH248MgSoftParameter15 | read-write | current | Parameter name index 15. It indicates the RTP source port filtering switch. Options: 1. no(1) -not filter without remote media. 2. yes(2) -filter without remot… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.18 | ColumnhwH248MgSoftParameter16 | read-write | current | Parameter name index 16. It indicates the length of the RTP source port filtering timer. This parameter is valid only when the RTP filtering is enabled. Range:… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.19 | ColumnhwH248MgSoftParameter17 | read-write | deprecated | Parameter name index 17. It indicates the context protection switch. It is unavailable in the VSPV1R2. Options: 1. yes(1) -the system releases the resource aut… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.20 | ColumnhwH248MgSoftParameter18 | read-write | deprecated | Parameter name index 18. It indicates the point-to-point fault report flag. Options: 1. yes(1) -report 2. no(2) -not report Default: yes(1) |
| 1.3.6.1.4.1.2011.6.36.1.28.1.21 | ColumnhwH248MgSoftParameter19 | read-write | deprecated | Parameter name index 19. It indicates the point-to-multipoint fault report flag. Options: 1. yes(1) -report 2. no(2) -not report Default: no(2) |
| 1.3.6.1.4.1.2011.6.36.1.28.1.22 | ColumnhwH248MgSoftParameter20 | read-write | deprecated | Parameter name index 20. It indicates the protocol version negotiation strategy. It is unavailable in the VSPV1R2. Options: 1. highest(1) -negotiate from the l… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.23 | ColumnhwH248MgSoftParameter21 | read-write | deprecated | Parameter name index 21. It is reserved in the system. Options: 1. yes(1) -yes 2. no(2) -no |
| 1.3.6.1.4.1.2011.6.36.1.28.1.24 | ColumnhwH248MgSoftParameter22 | read-write | current | Parameter name index 22. It indicates the type of the prompt tone that is played after MG is disconnected from MGC. Options: 1. bT(1) -busy tone 2. eET(2) -equ… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.25 | ColumnhwH248MgSoftParameter23 | read-write | current | Parameter name index 23.It indicates the length of synchronize-delay timer of port config state. Default: 35 Unit: second |
| 1.3.6.1.4.1.2011.6.36.1.28.1.26 | ColumnhwH248MgSoftParameter24 | read-write | current | Parameter name index 24. It indicates the number of rtp terminal. The maximum value is limited by product specification. |
| 1.3.6.1.4.1.2011.6.36.1.28.1.27 | ColumnhwH248MgSoftParameter25 | read-write | current | Parameter name index 25. It indicates max random value of the avalanche prevention system of the interface. Default: 60000 Unit: millisecond |
| 1.3.6.1.4.1.2011.6.36.1.28.1.28 | ColumnhwH248MgSoftParameter26 | read-write | current | Parameter name index 26. It indicates the local block tone type. Options: 1. busyTone(1) -busy tone 2. congestionTone(2) -congestion tone 3. muteTone(3) -mute … |
| 1.3.6.1.4.1.2011.6.36.1.28.1.29 | ColumnhwH248MgSoftParameter27 | read-write | current | Parameter name index 27. It indicates the remote block tone type. Options: 1. busyTone(1) -busy tone 2. congestionTone(2) -congestion tone 3. muteTone(3) -mute… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.30 | ColumnhwH248MgSoftParameter28 | read-write | current | Parameter name index 28. It indicates the length of howler tone. Default: 60 Unit: second |
| 1.3.6.1.4.1.2011.6.36.1.28.1.31 | ColumnhwH248MgSoftParameter29 | read-write | current | Parameter name index 29. It indicates the length of message waiting tone. Default: 3 Unit: second |
| 1.3.6.1.4.1.2011.6.36.1.28.1.32 | ColumnhwH248MgSoftParameter30 | read-write | current | Parameter name index 30. It indicates the length of long connect alarm. Default: 60 Unit: minute |
| 1.3.6.1.4.1.2011.6.36.1.28.1.33 | ColumnhwH248MgSoftParameter31 | read-write | current | Parameter name index 31. It indicates whether MG send long connect alarm. Options: 1. enable(1) -enable send long connect alarm 2. disable(2) -disable send lon… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.34 | ColumnhwH248MgSoftParameter32 | read-write | current | Parameter name index 32. The minimal length of port auto register timer. Default: 1800 Unit: second |
| 1.3.6.1.4.1.2011.6.36.1.28.1.35 | ColumnhwH248MgSoftParameter33 | read-write | current | Parameter name index 33. It indicates whether MG shutdown heartbeat. Options: 1. shutdown(1) -shutdown heartbeat 2. enable(2) -enable heartbeat Default: enable… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.36 | ColumnhwH248MgSoftParameter34 | read-write | current | Parameter name index 34. It indicates whether the gateway actively sets up or cancels the link for the BRA user when the softswitch issues the in-service or ou… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.37 | ColumnhwH248MgSoftParameter35 | read-write | current | Parameter name index 35. It indicates the mode for ISDN port is in service and out service. Options: 1. both(1) -supports in-service and out-of-service in sing… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.38 | ColumnhwH248MgSoftParameter36 | read-write | current | Parameter name index 36. Indicates the baseline interval of sending the registration message during the switchover between multi-homing MGCs. Default: 40 Unit:… |
| 1.3.6.1.4.1.2011.6.36.1.28.1.39 | ColumnhwH248MgSoftParameter37 | read-write | current | Parameter name index 37. The switch for the pulse signal switch to the DTMF signal. Options: 1. enable(1) -enable 2. disable(2) -disable Default: disable(2) |
| 1.3.6.1.4.1.2011.6.36.1.29 | TablehwH248DmmParaTable | not-accessible | current | This table is used to config the digitmap. The index of this table is hwH248DmmParaMgId. |
| 1.3.6.1.4.1.2011.6.36.1.29.1 | RowhwH248DmmParaEntry | not-accessible | current | This table is used to config the digitmap. The index of this entry is hwH248DmmParaMgId. |
| 1.3.6.1.4.1.2011.6.36.1.29.1.1 | ColumnhwH248DmmParaMgId | not-accessible | current | Indicates the MG ID. |
| 1.3.6.1.4.1.2011.6.36.1.29.1.2 | ColumnhwH248DmmParaStartTimer | read-write | current | Indicates the length of the DMM start timer. Unit: second |
| 1.3.6.1.4.1.2011.6.36.1.29.1.3 | ColumnhwH248DmmParaShortTimer | read-write | current | Indicates the length of the DMM short timer. Unit: second |
| 1.3.6.1.4.1.2011.6.36.1.29.1.4 | ColumnhwH248DmmParaLongTimer | read-write | current | Indicates the length of the DMM long timer Unit: second |
| 1.3.6.1.4.1.2011.6.36.1.29.1.6 | ColumnhwH248DmmParaDurationTimer | read-write | current | Indicates the length of the DMM duration timer. Unit: millisecond |
| 1.3.6.1.4.1.2011.6.36.1.31 | TablehwOverloadReservalTable | not-accessible | current | This table is used to config the DSP reserved parameter. The index of this table is hwDspOverloadReservalMgId. |
| 1.3.6.1.4.1.2011.6.36.1.31.1 | RowhwOverloadReservalEntry | not-accessible | current | This table is used to config the DSP reserved parameter. The index of this entry is hwDspOverloadReservalMgId. |
| 1.3.6.1.4.1.2011.6.36.1.31.1.1 | ColumnhwDspOverloadReservalMgId | not-accessible | current | Indicates the MG ID to be configured. |
| 1.3.6.1.4.1.2011.6.36.1.31.1.2 | ColumnhwTotalDspNum | read-write | current | Indicates the total count of DSPs. |
| 1.3.6.1.4.1.2011.6.36.1.31.1.3 | ColumnhwTotalDspUseNum | read-only | current | Indicates the total count of occupied DSPs. Default: 0 |
| 1.3.6.1.4.1.2011.6.36.1.31.1.4 | ColumnhwReservalCat1DspNum | read-write | current | Indicates the count of the DSPs of category 1. |
| 1.3.6.1.4.1.2011.6.36.1.31.1.5 | ColumnhwActualCat1DspUseNum | read-only | current | Indicates the count of the occupied DSPs of category 1. Default: 0 |
| 1.3.6.1.4.1.2011.6.36.1.31.1.6 | ColumnhwActualCat1CallUseDspNum | read-only | current | Indicates the count of the DSPs of category 1 occupied by calls. Default: 0 |
| 1.3.6.1.4.1.2011.6.36.1.31.1.7 | ColumnhwReservalCat2DspNum | read-write | current | Indicates the count of the DSPs of category 2. |
| 1.3.6.1.4.1.2011.6.36.1.31.1.8 | ColumnhwActualCat2DspUseNum | read-only | current | Indicates the count of the occupied DSPs of category 2. Default: 0 |
| 1.3.6.1.4.1.2011.6.36.1.31.1.9 | ColumnhwActualCat2CallUseDspNum | read-only | current | Indicates the count of the DSPs of category 2 occupied by calls. Default: 0 |
| 1.3.6.1.4.1.2011.6.36.1.31.1.10 | ColumnhwDspReservalCommonNum | read-only | current | Indicates the count of common DSPs reserved for configuration. |
| 1.3.6.1.4.1.2011.6.36.1.31.1.11 | ColumnhwActualCommonDspUseNum | read-only | current | Indicates the count of occupied common DSPs. Default: 0 |
| 1.3.6.1.4.1.2011.6.36.1.31.1.12 | ColumnhwActualCommonCallUseDspNum | read-only | current | Indicates the count of the common DSPs occupied by calls. Default: 0 |
| 1.3.6.1.4.1.2011.6.36.1.32 | TablehwH248TIDConfigTable | not-accessible | current | This table is used to config H248 terminal ID. The index of this table is hwVAGId. |
| 1.3.6.1.4.1.2011.6.36.1.32.1 | RowhwH248TIDConfigEntry | not-accessible | current | This table is used to config H248 terminal ID. The index of this entry is hwVAGId. |
| 1.3.6.1.4.1.2011.6.36.1.32.1.1 | ColumnhwVAGId | not-accessible | current | Media Gateway ID. |
| 1.3.6.1.4.1.2011.6.36.1.32.1.2 | ColumnhwH248BraPrefix | read-write | current | Indicates the BRA terminal prefix. |
| 1.3.6.1.4.1.2011.6.36.1.32.1.3 | ColumnhwH248PraPrefix | read-write | current | Indicates the PRA terminal prefix. |
| 1.3.6.1.4.1.2011.6.36.1.32.1.4 | ColumnhwH248PstnPrefix | read-write | current | Indicates the PSTN terminal prefix. |
| 1.3.6.1.4.1.2011.6.36.1.32.1.5 | ColumnhwH248RtpPrefix | read-write | current | Indicates the RTP terminal prefix. |
| 1.3.6.1.4.1.2011.6.36.1.32.1.6 | ColumnhwH248Separator | read-only | current | Indicates the terminal separator. |
| 1.3.6.1.4.1.2011.6.36.1.32.1.7 | ColumnhwH248R2Prefix | read-write | current | Indicates the R2 terminal prefix. |
| 1.3.6.1.4.1.2011.6.36.1.32.1.8 | ColumnhwH248DpnssPrefix | read-write | current | Indicates the DPNSS terminal prefix. |
| 1.3.6.1.4.1.2011.6.36.1.32.1.9 | ColumnhwH248Dass2Prefix | read-write | current | Indicates the DASS2 terminal prefix. |
| 1.3.6.1.4.1.2011.6.36.1.32.1.10 | ColumnhwH248BraTemplateIndex | read-write | current | Indicates the index of the BRA TID profile. |
| 1.3.6.1.4.1.2011.6.36.1.32.1.11 | ColumnhwH248PraTemplateIndex | read-write | current | Indicates the index of the PRA TID profile. |
| 1.3.6.1.4.1.2011.6.36.1.32.1.12 | ColumnhwH248PstnTemplateIndex | read-write | current | Indicates the index of the PSTN TID profile. |
| 1.3.6.1.4.1.2011.6.36.1.32.1.13 | ColumnhwH248RtpTemplateIndex | read-write | current | Indicates the index of the RTP TID profile. |
| 1.3.6.1.4.1.2011.6.36.1.32.1.14 | ColumnhwH248R2TemplateIndex | read-write | current | Indicates the index of the R2 TID profile. |
| 1.3.6.1.4.1.2011.6.36.1.32.1.15 | ColumnhwH248DpnssTemplateIndex | read-write | current | Indicates the index of the DPNSS TID profile. |
| 1.3.6.1.4.1.2011.6.36.1.32.1.16 | ColumnhwH248Dass2TemplateIndex | read-write | current | Indicates the index of the DASS2 TID profile. |
| 1.3.6.1.4.1.2011.6.36.1.32.1.17 | ColumnhwH248IsNeedToConfigTID | read-only | current | Indicates whether the terminal ID needs to be configured for the subscriber. Bit0 (low) to bit31 (high) respectively represent PSTN, BRA, PRA, DPNSS, DASS2, an… |
| 1.3.6.1.4.1.2011.6.36.1.67 | TablehwH248ProfileSupportTable | not-accessible | current | This table is used to set the H248 profile configuration. The index of this table is hwH248ProfileIndex. |
| 1.3.6.1.4.1.2011.6.36.1.67.1 | RowhwH248ProfileSupportEntry | not-accessible | current | This table is used to set the H248 profile configuration. The index of this entry is hwH248ProfileIndex. |
| 1.3.6.1.4.1.2011.6.36.1.67.1.1 | ColumnhwH248ProfileIndex | not-accessible | current | Indicates the profile index. |
| 1.3.6.1.4.1.2011.6.36.1.67.1.2 | ColumnhwH248ProfileCfgName | read-only | current | Indicates the configuration name of the profile. |
| 1.3.6.1.4.1.2011.6.36.1.67.1.3 | ColumnhwH248ProfileRegName | read-only | current | Indicates the registration name (that is, the negotiation name) of the profile. |
| 1.3.6.1.4.1.2011.6.36.1.68 | TablehwH248MedGwyCurTableTable | not-accessible | current | This table is used to query the current parameter configuration status of the MG interface. The index of this table is hwH248MgId. |
| 1.3.6.1.4.1.2011.6.36.1.68.1 | RowhwH248MedGwyCurTableEntry | not-accessible | current | This table is used to query the current parameter configuration status of the MG interface. The index of this entry is hwH248MgId. |
| 1.3.6.1.4.1.2011.6.36.1.68.1.1 | ColumnhwH248MgId | not-accessible | current | Indicates the MG ID. |
| 1.3.6.1.4.1.2011.6.36.1.68.1.2 | ColumnhwH248MedGwyProfileIndexCur | read-only | current | Indicates the profile index that is currently used by the MG. |
| 1.3.6.1.4.1.2011.6.36.1.68.1.3 | ColumnhwH248MedGwyH248VersionCur | read-only | current | Indicates the current H.248 version of the MG. Options: 1. v1(1) -version 1 2. v2(2) -version 2 3. v3(3) -version 3 |
| 1.3.6.1.4.1.2011.6.36.1.68.1.4 | ColumnhwH248MedGwyHeartBeatTimerCur | read-only | current | Indicates the current length of the initial heartbeat timer. The valid value range is 5..655, if the value is 0, the heartbeat is not started. Unit: second |
| 1.3.6.1.4.1.2011.6.36.1.68.1.5 | ColumnhwH248MedGwyMIDTypeCur | read-only | current | Indicates the current message MID type of the MG. Options: 1. ip4Address(1) -IP address 2. domainName(2) -domain name 3. deviceName(3) -device name |
| 1.3.6.1.4.1.2011.6.36.1.68.1.6 | ColumnhwH248MedGwyDeviceNameCur | read-only | current | Indicates the current device name of the MG. |
| 1.3.6.1.4.1.2011.6.36.1.68.1.7 | ColumnhwH248ProfileNegoParaCur | read-only | current | Indicates whether the profile currently used by the MG supports the profile parameter negotiation. Options: 1. disable(1) -disable 2. enable(2) -enable |
| 1.3.6.1.4.1.2011.6.36.1.68.1.8 | ColumnhwH248ProfileCfgNameCur | read-only | current | Indicates the configuration name of the H.248 profile currently used by the MG. |
| 1.3.6.1.4.1.2011.6.36.1.68.1.9 | ColumnhwH248ProfileNegoNameCur | read-only | current | Indicates the negotiation name of the H.248 profile currently used by the MG. |
| 1.3.6.1.4.1.2011.6.36.1.68.1.10 | ColumnhwH248MedGwySigIPAddrNameCur | read-only | current | Indicates the current working dynamic signal IP name. |
| 1.3.6.1.4.1.2011.6.36.1.68.1.11 | ColumnhwH248MedGwyMediaIPAddrNameCur | read-only | current | Indicates the current working dynamic media IP name. |
| 1.3.6.1.4.1.2011.6.36.1.68.1.12 | ColumnhwH248MedGwySigIPAddress1Cur | read-only | current | Indicates the signaling IP address of currently used by the MG. |
| 1.3.6.1.4.1.2011.6.36.1.68.1.13 | ColumnhwH248MedGwyMediaIPAddress1Cur | read-only | current | Indicates the media IP address of currently used by the MG. |
| 1.3.6.1.4.1.2011.6.36.2 | NodehwIASVoipTraps | |||
| 1.3.6.1.4.1.2011.6.36.2.0 | NodehwIASVoipAlarmTraps | |||
| 1.3.6.1.4.1.2011.6.36.2.0.1 | NotificationhwVpuDspChipFail | current | This notification indicates that the vpu dsp chip fail. | |
| 1.3.6.1.4.1.2011.6.36.2.0.2 | NotificationhwVpuDspChipRestore | current | This notification indicates that the vpu dsp chip restore form fault. | |
| 1.3.6.1.4.1.2011.6.36.2.0.3 | NotificationhwVpuFeInterfaceFail | current | This notification indicates that the vpu fe port fail. | |
| 1.3.6.1.4.1.2011.6.36.2.0.4 | NotificationhwVpuFeInterfaceRestore | current | This notification indicates that the vpu fe port restore from fault. | |
| 1.3.6.1.4.1.2011.6.36.2.0.5 | NotificationhwMedGwyFailAlarm | current | This notification indicates that the mg interface failed. | |
| 1.3.6.1.4.1.2011.6.36.2.0.6 | NotificationhwMedGwyRestoreAlarm | current | This notification indicates that the mg interface restore. | |
| 1.3.6.1.4.1.2011.6.36.2.0.7 | NotificationhwVpuSubbFail | current | This notification indicates that the vpu dsp sub board fail. | |
| 1.3.6.1.4.1.2011.6.36.2.0.8 | NotificationhwVpuSubbRestore | current | This notification indicates that the vpu dsp sub board restore. | |
| 1.3.6.1.4.1.2011.6.36.2.1 | NodehwIASVoipAlarmOids | |||
| 1.3.6.1.4.1.2011.6.36.2.1.1 | ScalarhwFEifIndex | read-only | current | Indicates the interface index (interface type + shelf + slot + port). |
| 1.3.6.1.4.1.2011.6.36.2.1.2 | ScalarhwVpuDspFailReason | read-only | current | Indicates the definition of the cause of the DSP chip fault. Options: 1. dspFault(1) -dsp fault 2. voipMoudleSoftwareOverload(2) -voip module software overload… |
| 1.3.6.1.4.1.2011.6.36.2.1.3 | ScalarhwVpuFeReson | read-only | current | Indicates the definition of the cause of the VPU FE port fault. Options: 1. peerNonautoneg(1) -peer nonautoneg 2. autonegSucc(2) -autoneg succeed 3. nonautoneg… |
| 1.3.6.1.4.1.2011.6.36.2.1.4 | ScalarhwVpuSubBIndex | read-only | current | Indicates the VPU subboard index. |
| 1.3.6.1.4.1.2011.6.36.2.1.5 | ScalarhwVpuDspChipIndex | read-only | current | Indicates the VPU DSP chip index. |
| 1.3.6.1.4.1.2011.6.36.2.1.6 | ScalarhwMedGwyAlarmMgId | read-only | current | Indicates the MG ID. |
| 1.3.6.1.4.1.2011.6.36.3 | NodehwIASH248TrapsVbOids | |||
| 1.3.6.1.4.1.2011.6.36.3.1 | ScalarhwH248TrapRequestID | accessible-for-notify | current | The h248 trap request ID. |
| 1.3.6.1.4.1.2011.6.36.3.2 | ScalarhwH248MgStatus | accessible-for-notify | current | The status of the h248 media gateway. Options: 1. up(1) -normal 2. close(2) -closed 3. gracefulClose(3) -graceful closing 4. waitAck(4) -waiting for ACK 5. fau… |
| 1.3.6.1.4.1.2011.6.36.3.3 | ScalarhwH248TrapLastChangeTime | accessible-for-notify | current | The value of sysUpTime at the time the media gateway or the media gateway control entered its current status or media gateway control switched. |
| 1.3.6.1.4.1.2011.6.36.3.4 | ScalarhwH248MgcIpAddress | accessible-for-notify | current | The mgc ip address. |
| 1.3.6.1.4.1.2011.6.36.3.5 | ScalarhwH248MgcIndex | accessible-for-notify | current | The current mgc index. |
| 1.3.6.1.4.1.2011.6.36.3.6 | ScalarhwH248MgcStatus | accessible-for-notify | current | The media gateway control status. Options: 1. up(1) -active 2. down(2) -shut down 3. standby(3) -standby |
| 1.3.6.1.4.1.2011.6.36.3.7 | ScalarhwH248Frame | accessible-for-notify | current | The frame where mg user is configed. |
| 1.3.6.1.4.1.2011.6.36.3.8 | ScalarhwH248Slot | accessible-for-notify | current | The slot where mg user is configed. |
| 1.3.6.1.4.1.2011.6.36.3.9 | ScalarhwH248Port | accessible-for-notify | current | The port where mg user is configed. |
| 1.3.6.1.4.1.2011.6.36.3.10 | ScalarhwH248LongConnectDuration | accessible-for-notify | current | The duration of a long connect. |
| 1.3.6.1.4.1.2011.6.36.3.11 | ScalarhwH248UserTelNo | accessible-for-notify | current | The user telphone number. |
| 1.3.6.1.4.1.2011.6.36.3.12 | ScalarhwH248MgcPort | accessible-for-notify | current | The UDP port of MGC connected. |
| 1.3.6.1.4.1.2011.6.36.3.13 | ScalarhwH248OnlineUser | accessible-for-notify | current | The number of online user. |
| 1.3.6.1.4.1.2011.6.36.3.14 | ScalarhwH248InnerCall | accessible-for-notify | current | The number of inner-call. |
| 1.3.6.1.4.1.2011.6.36.3.15 | ScalarhwH248RejectCall | accessible-for-notify | current | The number of calls rejected. |
| 1.3.6.1.4.1.2011.6.36.3.16 | ScalarhwH248IsConfigTid | accessible-for-notify | current | Indicates whether the terminal ID needs to be configured for the subscriber. Bit0 (low) to bit31 (high) respectively represent PSTN, BRA, PRA, DPNSS, DASS2, an… |
| 1.3.6.1.4.1.2011.6.36.3.17 | ScalarhwH248IsUpdateTid | accessible-for-notify | current | Indicates whether the terminal ID needs to be updated for the subscriber. Bit0 (low) to bit31 (high) respectively represent PSTN, BRA, PRA, DPNSS, DASS2, and R… |
| 1.3.6.1.4.1.2011.6.36.4 | NodehwIASH248Traps | |||
| 1.3.6.1.4.1.2011.6.36.4.1 | NodehwIASH248CommonTraps | |||
| 1.3.6.1.4.1.2011.6.36.4.1.0 | NodehwIASH248CommonTrapsPrefix | |||
| 1.3.6.1.4.1.2011.6.36.4.1.0.1 | NotificationhwIASH248ResetTrap | current | This notification indicates that the result of h248 media gateway reset operation. | |
| 1.3.6.1.4.1.2011.6.36.4.1.0.2 | NotificationhwIASH248ShutdownTrap | current | This notification indicates that the h248 media gateway shutdown result. | |
| 1.3.6.1.4.1.2011.6.36.4.1.0.3 | NotificationhwIASH248MgStateTrap | current | This notification indicates that the h248 media gateway status changes. | |
| 1.3.6.1.4.1.2011.6.36.4.1.0.4 | NotificationhwIASH248MgcSwitchTrap | current | This notification indicates that the h248 media gateway control switchs. | |
| 1.3.6.1.4.1.2011.6.36.4.1.0.5 | NotificationhwIASH248MgcStateTrap | current | This notification indicates that the h248 media gateway status changed. | |
| 1.3.6.1.4.1.2011.6.36.4.1.0.6 | NotificationhwIASH248MgLableTrap | current | This notification indicates that the userlabel of the H248 interface changed. | |
| 1.3.6.1.4.1.2011.6.36.4.1.0.7 | NotificationhwIASH248TidUpdateTrap | current | This notification indicates that the H248 terminal ID updated. | |
| 1.3.6.1.4.1.2011.6.36.4.2 | NodehwIASH248AlarmTraps | |||
| 1.3.6.1.4.1.2011.6.36.4.2.0 | NodehwIASH248AlarmTrapsPrefix | |||
| 1.3.6.1.4.1.2011.6.36.4.2.0.1 | NotificationhwIASH248MgFaultTrap | current | This notification indicates that the h248 media gateway is closed. | |
| 1.3.6.1.4.1.2011.6.36.4.2.0.2 | NotificationhwIASH248MgRestoreTrap | current | This notification indicates that the h248 media gateway is normal. | |
| 1.3.6.1.4.1.2011.6.36.4.2.0.3 | NotificationhwIASH248AbsentBandwidthTrap | current | This notification indicates that bandwidth occupied by VoIP calls exceeds the threshold. | |
| 1.3.6.1.4.1.2011.6.36.4.2.0.4 | NotificationhwIASH248LongConnectTrap | current | This notification indicates that the H248 user has calls for a long time. |