IBM-GbTOR-G8052-MIB
5596 objects
MIB for IBM Networking Operating System RackSwitch G8052 All Rights reserved DEVICE VERSION: 7.11.3.0
Imported Objects
| BRIDGE-MIB | BridgeId dot1dBasePort dot1dBasePortEntry dot1dBridge dot1dTp dot1dTpPort |
| IF-MIB | InterfaceIndex InterfaceIndexOrZero |
| INET-ADDRESS-MIB | InetAddress InetAddressIPv6 InetAddressType |
| P-BRIDGE-MIB | EnabledStatus |
| Q-BRIDGE-MIB | PortList |
| RFC1155-SMI | enterprises |
| RFC1213-MIB | ifIndex sysContact sysLocation sysName |
| SNMP-FRAMEWORK-MIB | SnmpAdminString SnmpEngineID SnmpMessageProcessingModel SnmpSecurityLevel SnmpSecurityModel |
| SNMP-USER-BASED-SM-MIB | usmNoAuthProtocol usmNoPrivProtocol |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 Gauge32 Integer32 IpAddress mib-2 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-IDENTITY OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | AutonomousType DisplayString MacAddress PhysAddress RowPointer RowStatus StorageType TAddress TDomain TEXTUAL-CONVENTION TimeInterval TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.26543 | Nodeblade | |||
| 1.3.6.1.4.1.26543.1 | Noderegistration | |||
| 1.3.6.1.4.1.26543.1.7 | Nodeibm-switch | |||
| 1.3.6.1.4.1.26543.1.7.7 | Nodeg8052 | |||
| 1.3.6.1.4.1.26543.2 | Nodeprivate-mibs | |||
| 1.3.6.1.4.1.26543.2.7 | Nodeibm-switch-mgmt | |||
| 1.3.6.1.4.1.26543.2.7.7 | Nodeg8052-mgmt | |||
| 1.3.6.1.4.1.26543.2.7.7.1 | Nodeagent | |||
| 1.3.6.1.4.1.26543.2.7.7.1.1 | NodeagentConfig | |||
| 1.3.6.1.4.1.26543.2.7.7.1.1.1 | NodeagSystem | |||
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.2 | ScalaragApplyConfiguration | read-write | current | This is an action object to apply the changes made to configuration of the switch. By setting the value to apply(2), all the changes made since the last apply … |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.3 | ScalaragSavePending | read-only | current | This object, when read, gives the user information whether an save action is needed and that the configuration has been applied but not saved to the flash. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.4 | ScalaragSaveConfiguration | read-write | current | This is an action object to write current configuration to nonvolatile storage. When issued with the saveActive, the active configuration in flash is saved to … |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.5 | ScalaragRevert | read-write | current | This is an action object to revert the unapplied changes made to the switch. By setting the value to revert(2), all the unapplied changes will be reverted. Thi… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.7 | ScalaragReset | read-write | current | This is an action object to reboot the agent. other(1) is returned always when read. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.8 | ScalaragConfigForNxtReset | read-write | current | The configuration information to be loaded from at next reset. The following values are writable: active(2)...active configuration block backup(3)...backup con… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.9 | ScalaragImageForNxtReset | read-write | current | The software image to be booted from at next reset. The following values are writable: image1(2)...image 1 image2(3)...image 2 |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.10 | ScalaragSoftwareVersion | read-only | current | The version of the software image that is currently running on the system in the form of 'major.minor.maintenance.bugfix'. A zero length string is returned if … |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.11 | ScalaragBootVer | read-only | current | The version of the boot code in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.12 | ScalaragImage1Ver | read-only | current | The version of the software image stored in image 1 storage in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available o… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.13 | ScalaragImage2Ver | read-only | current | The version of the software image stored in image 2 storage in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available o… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.14 | ScalaragRtcDate | read-write | current | The date on the real time clock in the form of 'mm/dd/yy'. A zero length string is returned if date is not available. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.15 | ScalaragRtcTime | read-write | current | The time on the real time clock in the form of 'hh:mm:ss'. A zero length string is returned if time is not available. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.16 | ScalaragLastSetErrorReason | read-only | current | The error reason of the last SET failure. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.17 | ScalaragCurCfgHttpServerPort | read-only | current | The TCP port number that the HTTP server is listening to in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.18 | ScalaragNewCfgHttpServerPort | read-write | current | The TCP port number that the HTTP server is listening to in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.19 | ScalaragCurCfgLoginBanner | read-only | current | The user defined login banner. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.20 | ScalaragNewCfgLoginBanner | read-write | current | The user defined login banner. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.23 | ScalaragCurCfgConsole | read-only | current | Enable or disable console output of syslog messages. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.24 | ScalaragNewCfgConsole | read-write | current | Enable or disable console output of syslog messages. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.31 | ScalaragSlotNumber | read-only | current | Identifies the slot in which this switch is installed. If the agent implementing this MIB is not a blade in a chassis this value has no meaning. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.32 | ScalaragCurCfgSnmpTimeout | read-only | current | Once SNMP operations like agApplyConfig, agDiffState and agDumpState, which use the state machine are done the resources used by these operations need to be fr… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.33 | ScalaragNewCfgSnmpTimeout | read-write | current | Once SNMP operations like agApplyConfig, agDiffState and agDumpState, which use the state machine are done the resources used by these operations need to be fr… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.34 | ScalaragCurCfgTelnetServerPort | read-only | current | The TCP port number that the telnet server listens for telnet sessions. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.35 | ScalaragNewCfgTelnetServerPort | read-write | current | The TCP port number that the telnet server listens for telnet sessions. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.36 | ScalaragClearFlashDump | read-write | current | This is an action object to clear the FLASH dump. ok(1) is returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.39 | ScalaragCurCfgTrapSrcIf | read-only | current | The SNMP trap source interface number. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.40 | ScalaragNewCfgTrapSrcIf | read-write | current | The SNMP trap source interface number. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.49 | ScalaragCurCfgHttpsServerPort | read-only | current | The TCP port number that the HTTPS server is listening to in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.50 | ScalaragNewCfgHttpsServerPort | read-write | current | The TCP port number that the HTTPS server is listening to in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.51 | ScalaragCurCfgTftpServerPort | read-only | current | The TCP port number that the TFTP server is listening to in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.52 | ScalaragNewCfgTftpServerPort | read-write | current | The TCP port number that the TFTP server is listening to in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.53 | ScalaragRackId | read-only | current | The rack unique identifier. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.54 | ScalaragChassis | read-only | current | Chassis serial number. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.55 | ScalaragCurTimeZone | read-only | current | The time zone. Note: Locations are alphabetically ordered and the corresponding code is not reflected in CLI. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.56 | ScalaragNewTimeZone | read-write | current | The time zone. Note: Locations are alphabetically ordered and the corresponding code is not reflected in CLI. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.57 | ScalaragCurCfgIdleCLITimeout | read-only | current | Set idle CLI sessions timeout. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.58 | ScalaragNewCfgIdleCLITimeout | read-write | current | Set idle CLI sessions timeout. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.62 | ScalaragCurCfgHttpsServerAccess | read-only | current | Current HTTPS server access state. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.63 | ScalaragNewCfgHttpsServerAccess | read-write | current | Enable/disable HTTPS server access. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.66 | ScalaragCurHttpAcces | read-only | current | Current HTTP server access state. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.67 | ScalaragNewHttpAcces | read-write | current | New HTTP server access state. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.68 | ScalaragCurCfgDhcp | read-only | current | Enable or disable the use of DHCP, as currently configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.69 | ScalaragNewCfgDhcp | read-write | current | Enable or disable the use of DHCP, in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.72 | ScalaragCurCfgHprompt | read-only | current | Current status of hprompt. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.73 | ScalaragNewCfgHprompt | read-write | current | New status of hprompt. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.74 | ScalaragCurCfgUserBBI | read-only | current | Current status of user configuration from BBI. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.75 | ScalaragNewCfgUserBBI | read-write | current | New status of user configuration from BBI. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.78 | ScalaragCurCfgLoginNotice | read-only | current | The user defined login notice. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.79 | ScalaragNewCfgLoginNotice | read-write | current | The user defined login notice. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.98 | ScalaragCurCfgSysCustomDstState | read-only | current | The current status of Custom DST |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.99 | ScalaragNewCfgSysCustomDstState | read-write | current | Enable/disable Custom DST |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.100 | ScalaragCurCfgSysCustomDstStart | read-only | current | The current Custom DST start rule |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.101 | ScalaragNewCfgSysCustomDstStart | read-write | current | Set Custom DST start rule |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.102 | ScalaragCurCfgSysCustomDstEnd | read-only | current | The current Custom DST end rule |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.103 | ScalaragNewCfgSysCustomDstEnd | read-write | current | Set Custom DST end rule |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.104 | ScalaragHavePanicDump | read-only | current | The presence of a panic dump in the flash memory. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.111 | ScalaragCurCfgResetControl | read-only | current | Current reset control state. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.112 | ScalaragNewCfgResetControl | read-write | current | Enable/disable reset control after panic. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.113 | ScalaragCurCfgSysDlight | read-only | current | Current daylight savings time status. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.114 | ScalaragNewCfgSysDlight | read-write | current | Enable/disable daylight savings time. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.115 | ScalaragCurCfgErrDisableRecovery | read-only | current | This object indicates whether the system will automatically re-enable an error-disabled port after the time interval indicated by agCurCfgErrDisableTimeout has… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.116 | ScalaragNewCfgErrDisableRecovery | read-write | current | This object specifies whether the system should automatically re-enable an error-disabled port. Use this object to change the global setting of the error-disab… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.117 | ScalaragCurCfgErrDisableTimeout | read-only | current | This object indicates the time, in seconds, that the system will wait before it automatically re-enables any port that is in error-disabled state. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.118 | ScalaragNewCfgErrDisableTimeout | read-write | current | This object specifies the time, in seconds, that the system should wait before it automatically re-enables a port that is in error-disabled state. Use this obj… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.119 | ScalaragCurCfgTelnetAccess | read-only | current | Current telnet access state. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.120 | ScalaragNewCfgTelnetAccess | read-write | current | Enable/disable telnet access. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.127 | ScalarserverPortsCurCfgPorts | read-only | current | The current configured server port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ p… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.128 | ScalarserverPortsNewCfgPorts | read-only | current | New configuration server port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.129 | ScalarserverPortsNewCfgAddPort | read-create | current | The port to be added to the server ports list. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.130 | ScalarserverPortsNewCfgRemovePort | read-create | current | The port to be removed from the server ports list. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.131 | ScalaragCurBootProfile | read-only | current | Profile that will be used by the switch after reset |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.132 | ScalaragNewBootProfile | read-write | current | Configure the profile that will be used by the switch after reset |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.133 | ScalaragNetboot | read-write | current | Ena/dis loading of config over n/w during bootup |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.134 | ScalaragNetbootTftpAddr | read-write | current | Tftp server address from where config file needs to be downloaded |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.135 | ScalaragNetbootCfgFile | read-write | current | Config file location on tftp server |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.136 | ScalaragCurCfgLinkscanMode | read-only | current | Set linkscan mode |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.137 | ScalaragNewCfgLinkscanMode | read-write | current | Set linkscan mode |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.138 | ScalaragUSBboot | read-write | current | Ena/dis USB Boot capability |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.139 | ScalaragCurServiceLED | read-only | current | Ena/dis Service Required LED |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.140 | ScalaragNewServiceLED | read-write | current | Ena/dis Service Required LED |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.141 | ScalaragUSBeject | read-write | current | Eject USB - eject(1) Get current USB state: usbready(2) - USB mounted nousb(3) - no USB mounted |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.142 | ScalaragCurRFC4741NetconfAccess | read-only | current | Current NETCONF server access state. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.143 | ScalaragNewRFC4741NetconfAccess | read-write | current | Enable/disable NETCONF server access state. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.144 | ScalaragCurRFC4741NetconfSessionTimeout | read-only | current | Once NETCONF session setup, NETCONF server will allocate resource for this session. agCurRFC4741NetconfSessionTimeout indicates the number of seconds before th… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.145 | ScalaragNewRFC4741NetconfSessionTimeout | read-write | current | Once NETCONF session setup, NETCONF server will allocate resource for this session. agNewRFC4741NetconfSessionTimeout specifies the number of seconds before th… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.146 | ScalaragCurRFC4741NetconfSshAccess | read-only | current | Current NETCONF server over SSH access state. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.147 | ScalaragNewRFC4741NetconfSshAccess | read-write | current | Enable/disable NETCONF server over SSH access state. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.148 | ScalaragCurRFC4741NetconfSshPort | read-only | current | The TCP port number that the NETCONF server over SSH is listening to in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.149 | ScalaragNewRFC4741NetconfSshPort | read-write | current | The TCP port number that the NETCONF server over SSH is listening to in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.158 | ScalaragCurCfgLFDStatus | read-only | current | This object indicates whether the system will put any port in an error-disabled state due to excessive link flaps. A port will be put in an error-disabled stat… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.159 | ScalaragNewCfgLFDStatus | read-write | current | This object indicates whether the system should put any port in an error-disabled state due to excessive link flaps. Use this object to change the global setti… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.160 | ScalaragCurCfgLFDFlaps | read-only | current | This object indicates the maximum number of flaps allowed in a time period set by agCurCfgLFDTime. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.161 | ScalaragNewCfgLFDFlaps | read-write | current | This object specifies the maximum number of flaps that should be allowed in a time period. Use this object to change the global maximum number of flaps allowed… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.162 | ScalaragCurCfgLFDTime | read-only | current | This object indicates the length of time period in seconds during which link flaps are counted. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.163 | ScalaragNewCfgLFDTime | read-write | current | This object specifies the length of time period in seconds that should be used to count link flaps. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.164 | ScalaragCurCfgTrapSrcLoopIf | read-only | current | The index of the loopback interface that should be used for the source IP of the SNMP trap; 0 means that no loopback interface is used as the source of the SNM… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.165 | ScalaragNewCfgTrapSrcLoopIf | read-write | current | The index of the loopback interface that should be used for the source IP of the SNMP trap; 0 means that no loopback interface is used as the source of the SNM… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.166 | ScalaragCfgMtm | read-write | current | This object specifies the new value for MTM. The available MTM values are: 1455-48E (1) 7309-52F (2) 7309-G52 (3) 7309-HC2 (4) 7309-HC1 (5) 7120-48E (6) |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.167 | ScalaragCurCfgDefipData | read-only | current | Enable or disable the use of default IP address on data interface, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.168 | ScalaragNewCfgDefipData | read-write | current | Enable or disable the use of default IP address on data interface, in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.177 | ScalaragNewSecurityMode | read-write | current | This is an action object to change switch security mode. There are thtree security modes for IBM switch: strict mode, compatibility mode and strict mode with S… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.178 | ScalaragNewCfgSslVersionLevel | read-write | current | New status of SSL Server Minimum Acceptable Protocol Version. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.179 | ScalaragCurCfgSslVersionLevel | read-only | current | Current status of SSL Server Minimum Acceptable Protocol Version. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.180 | ScalaragCurSecurityMode | read-only | current | This is an action object to change switch security mode. There are thtree security modes for IBM switch: strict mode, compatibility mode and strict mode with S… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.184 | TableagCurCfgTrapHostTable | not-accessible | current | The table of current trap hosts configure. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.184.1 | RowagCurCfgTrapHostEntry | not-accessible | current | A trap host configuration on the switch. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.184.1.1 | ColumnagCurCfgTrapHostIndex | read-only | current | The trap host index. Valid range is 1-16 |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.184.1.2 | ColumnagCurCfgTrapHostAddress | read-only | current | The trap host address. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.184.1.3 | ColumnagCurCfgTrapHostCommStr | read-only | current | The trap host community string. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.185 | TableagNewCfgTrapHostTable | not-accessible | current | The table for trap host definitions in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.185.1 | RowagNewCfgTrapHostEntry | not-accessible | current | A row in the trap host definition table |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.185.1.1 | ColumnagNewCfgTrapHostIndex | read-only | current | The trap host index. Valid range is 1-16 |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.185.1.2 | ColumnagNewCfgTrapHostAddress | read-create | current | The trap host address in the new configuration block. Setting IPv6 value is not supported in realease 7.9.x. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.185.1.3 | ColumnagNewCfgTrapHostCommStr | read-create | current | The trap host community string in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.1.185.1.4 | ColumnagNewCfgTrapHostDelete | read-create | current | By setting the value to delete(2), the entire row is deleted. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2 | NodeagPortConfig | |||
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.1 | ScalaragPortTableMaxEnt | read-only | current | The maximum number of rows in the port configuration host table. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2 | TableagPortCurCfgTable | not-accessible | current | The table of port configuration in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1 | RowagPortCurCfgTableEntry | not-accessible | current | A row in the port table in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.1 | ColumnagPortCurCfgIndx | read-only | current | The index of the row in port configurations table. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.2 | ColumnagPortCurCfgState | read-only | current | This is the state of the port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.3 | ColumnagPortCurCfgVlanTag | read-only | current | This is VLAN tag state of the port |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.5 | ColumnagPortCurCfgRmon | read-only | current | This object is used to turn RMON on or off on the port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.6 | ColumnagPortCurCfgPVID | read-only | current | The default VLAN ID for the port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.11 | ColumnagPortCurCfgGigEthAutoNeg | read-only | current | This object is used to turn the autonegotiation on or off for gigabit Ethernet connection. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.12 | ColumnagPortCurCfgGigEthFctl | read-only | current | This object is used to select port flow control for gigabit Ethernet connection. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.13 | ColumnagPortCurCfgPortName | read-only | current | The switch port name. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.16 | ColumnagPortCurCfgLinkTrap | read-only | current | Indicates whether linkUp/linkDown traps should be generated for this interface. By default, this object should have the value enabled(1) for interfaces which d… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.21 | ColumnagPortCurCfgGigEthSpeed | read-only | current | Selects the port speed for Gigabit Ethernet connection. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.22 | ColumnagPortCurCfgGigEthMode | read-only | current | This object is used to select port mode for Gigabit Ethernet connection. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.23 | ColumnagPortCurCfgDscpRemarking | read-only | current | Enable or disable Dscp remarking for the switch port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.24 | ColumnagPortCurCfgPortAlias | read-only | current | The switch port alias. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.25 | ColumnagPortCurCfgTagPVID | read-only | current | This is PVID tag state of the port |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.26 | ColumnagPortCurCfgLearning | read-only | current | Enable or disable L2 (FDB) Learning for the switch port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.27 | ColumnagPortCurCfgFloodBlocking | read-only | current | Enable or disable flood blocking for the switch port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.29 | ColumnagPortCurCfgType | read-only | current | The switch port type. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.30 | ColumnagPortCurCfgLinkType | read-only | current | The type of port connection. (for PVRST only) |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.31 | ColumnagPortCurCfgEdge | read-only | current | The state of port edge. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.35 | ColumnagPortCurCfgErrDisableRecovery | read-only | current | This object indicates whether the system will automatically re-enable this port if it becomes error-disabled. This port will be re-enabled after the time inter… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.37 | ColumnagPortCurCfgUdld | read-only | current | Enable or disable UDLD for the switch port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.38 | ColumnagPortCurCfgUdldMode | read-only | current | Enable or disable UDLD mode for the switch port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.39 | ColumnagPortCurCfgOam | read-only | current | Enable or disable OAM Discovery process for the switch port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.40 | ColumnagPortCurCfgOamMode | read-only | current | Enable or disable OAM mode for the switch port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.41 | ColumnagPortCurCfgBpduGuard | read-only | current | Enable or disable BPDU guard for the switch port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.42 | ColumnagPortCurCfgMulticastThreshold | read-only | current | Current status of the port's Multicast Threshold. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.43 | ColumnagPortCurCfgMulticastThresholdRate | read-only | current | Current port's Multicast Threshold Rate. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.44 | ColumnagPortCurCfgBroadcastThreshold | read-only | current | Current status of the port's Broadcast Threshold. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.45 | ColumnagPortCurCfgBroadcastThresholdRate | read-only | current | Current port's Broadcast Threshold Rate. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.46 | ColumnagPortCurCfgDLFThreshold | read-only | current | Current status of the port's Destination Lookup Fail Threshold. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.47 | ColumnagPortCurCfgDLFThresholdRate | read-only | current | Current port's Destination Lookup Fail Threshold Rate. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.48 | ColumnagPortCurCfgMacAddrNotif | read-only | current | This is the state of the MAC address notification syslog messages on the port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.49 | ColumnagPortCurCfgTagiPVID | read-only | current | This is ingress PVID tag state of the port |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.52 | ColumnagPortCurCfgStpExtGuard | read-only | current | Current state for spanning tree guard type |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.53 | ColumnagPortCurCfgLFDStatus | read-only | current | This object indicates whether the system will put this port in an error-disabled state due to excessive link flaps. A port will be put in an error-disabled sta… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.56 | ColumnagPortCurCfgEvbProfId | read-only | current | Current EVB Profile ID |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.59 | ColumnagPortCurCfgReflectRelay | read-only | current | Current state of reflective relay |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.61 | ColumnagPortCurCfgPrivateVlanStatus | read-only | current | Current state of Private VLAN on this port |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.62 | ColumnagPortCurCfgMappedPrimaryVlans | read-only | current | Primary VLAN list mapped to port. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vlan 8 || || || ||___ vlan 7 || |____ vlan 6 || . … |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.2.1.63 | ColumnagPortCurCfgAssociatedSecondaryVlans | read-only | current | Secondary VLAN list associated to port. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vlan 8 || || || ||___ vlan 7 || |____ vlan 6… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3 | TableagPortNewCfgTable | not-accessible | current | The table of port configuration in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1 | RowagPortNewCfgTableEntry | not-accessible | current | A row in the port configuration table in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.1 | ColumnagPortNewCfgIndx | read-only | current | The index of the row in port configurations table. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.2 | ColumnagPortNewCfgState | read-write | current | This is the state of the port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.3 | ColumnagPortNewCfgVlanTag | read-write | current | This is VLAN tag state of the port |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.5 | ColumnagPortNewCfgRmon | read-write | current | This object is used to turn RMON on or off on the port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.6 | ColumnagPortNewCfgPVID | read-write | current | The default VLAN ID for the port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.11 | ColumnagPortNewCfgGigEthAutoNeg | read-write | current | This object is used to turn the autonegotiation on or off for gigabit Ethernet connection. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.12 | ColumnagPortNewCfgGigEthFctl | read-write | current | This object is used to select port flow control for gigabit Ethernet connection. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.13 | ColumnagPortNewCfgPortName | read-write | current | The switch port name. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.16 | ColumnagPortNewCfgLinkTrap | read-write | current | Indicates whether linkUp/linkDown traps should be generated for this interface. By default, this object should have the value enabled(1) for interfaces which d… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.21 | ColumnagPortNewCfgGigEthSpeed | read-write | current | Selects the port speed for Gigabit Ethernet connection. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.22 | ColumnagPortNewCfgGigEthMode | read-write | current | This object is used to select port mode for Gigabit Ethernet connection. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.23 | ColumnagPortNewCfgDscpRemarking | read-write | current | Enable or disable Dscp remarking for the switch port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.25 | ColumnagPortNewCfgTagPVID | read-write | current | This is PVID tag state of the port |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.26 | ColumnagPortNewCfgLearning | read-write | current | Enable or disable L2 (FDB) Learning for the switch port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.27 | ColumnagPortNewCfgFloodBlocking | read-write | current | Enable or disable flood blocking for the switch port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.29 | ColumnagPortNewCfgType | read-only | current | The switch port type. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.30 | ColumnagPortNewCfgLinkType | read-create | current | The type of port connection. (for PVRST only) |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.31 | ColumnagPortNewCfgEdge | read-create | current | The state of port edge. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.35 | ColumnagPortNewCfgErrDisableRecovery | read-write | current | This object specifies whether the system should automatically re-enable this port when it becomes error-disabled. Use this object to change the port-level sett… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.37 | ColumnagPortNewCfgUdld | read-write | current | Enable or disable UDLD for the switch port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.38 | ColumnagPortNewCfgUdldMode | read-write | current | Enable or disable UDLD mode for the switch port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.39 | ColumnagPortNewCfgOam | read-write | current | Enable or disable OAM Discovery process for the switch port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.40 | ColumnagPortNewCfgOamMode | read-write | current | Enable or disable OAM mode for the switch port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.41 | ColumnagPortNewCfgBpduGuard | read-write | current | Enable or disable BPDU guard for the switch port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.42 | ColumnagPortNewCfgMulticastThreshold | read-write | current | New status of the port's Multicast Threshold. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.43 | ColumnagPortNewCfgMulticastThresholdRate | read-write | current | New port's Multicast Threshold Rate. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.44 | ColumnagPortNewCfgBroadcastThreshold | read-write | current | New status of the port's Broadcast Threshold. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.45 | ColumnagPortNewCfgBroadcastThresholdRate | read-write | current | New port's Broadcast Threshold Rate. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.46 | ColumnagPortNewCfgDLFThreshold | read-write | current | New status of the port's Destination Lookup Fail Threshold. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.47 | ColumnagPortNewCfgDLFThresholdRate | read-write | current | New port's Destination Lookup Fail Threshold Rate. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.48 | ColumnagPortNewCfgMacAddrNotif | read-write | current | Enables or Disables the MAC address notification syslog messages on the port. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.49 | ColumnagPortNewCfgTagiPVID | read-write | current | This is ingress PVID tag state of the port |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.52 | ColumnagPortNewCfgStpExtGuard | read-write | current | Set spanning tree guard type |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.53 | ColumnagPortNewCfgLFDStatus | read-write | current | This object indicates whether the system should put this port in an error-disabled state due to excessive link flaps. Use this object to change the port settin… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.56 | ColumnagPortNewCfgEvbProfId | read-write | current | Set EVB Profile ID |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.59 | ColumnagPortNewCfgReflectRelay | read-write | current | Enable/disable reflective relay for port |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.61 | ColumnagPortNewCfgPrivateVlanStatus | read-write | current | Enable or disable the Private VLAN on this port |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.62 | ColumnagPortNewCfgMappedPrimaryVlans | read-only | current | Primary VLAN list mapped to port. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vlan 8 || || || ||___ vlan 7 || |____ vlan 6 || . … |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.63 | ColumnagPortNewCfgAddPrimaryVlan | read-write | current | Adds the port to the specified primary VLAN. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.64 | ColumnagPortNewCfgDelPrimaryVlan | read-write | current | Removes the port from the specified primary VLAN. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.65 | ColumnagPortNewCfgAssociatedSecondaryVlans | read-only | current | Secondary VLAN list associated to port. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vlan 8 || || || ||___ vlan 7 || |____ vlan 6… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.66 | ColumnagPortNewCfgAddSecondaryVlan | read-write | current | Adds the port to the specified secondary VLAN. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.2.3.1.67 | ColumnagPortNewCfgDelSecondaryVlan | read-write | current | Removes the port from the secondary VLAN. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3 | NodeagRadiusConfig | |||
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.1 | ScalarradCurCfgPrimaryServer | read-only | current | The Hostname of the Primary RADIUS server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.2 | ScalarradNewCfgPrimaryServer | read-write | current | The Hostname of the Primary RADIUS server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.3 | ScalarradCurCfgSecondaryServer | read-only | current | The Hostname of the Secondary RADIUS server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.4 | ScalarradNewCfgSecondaryServer | read-write | current | The Hostname of the Secondary RADIUS server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.5 | ScalarradCurCfgPort | read-only | current | Specify the RADIUS port number. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.6 | ScalarradNewCfgPort | read-write | current | Specify the RADIUS port number. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.7 | ScalarradCurCfgTimeout | read-only | current | The maximum number of seconds before resending authentication to RADIUS server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.8 | ScalarradNewCfgTimeout | read-write | current | The maximum number of seconds before resending authentication to RADIUS server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.9 | ScalarradCurCfgRetries | read-only | current | Number of retries to the RADIUS server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.10 | ScalarradNewCfgRetries | read-write | current | Number of retries to the RADIUS server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.11 | ScalarradCurCfgState | read-only | current | Enable or disable RADIUS authentication. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.12 | ScalarradNewCfgState | read-write | current | Enable or disable RADIUS authentication. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.13 | ScalarradCurCfgAuthenString | read-only | current | The RADIUS authentication string. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.14 | ScalarradNewCfgAuthenString | read-write | current | The RADIUS authentication string. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.15 | ScalarradCurCfgBackdoor | read-only | current | Enable or disable RADIUS backdoor for telnet/ssh/http/https. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.16 | ScalarradNewCfgBackdoor | read-write | current | Enable or disable RADIUS backdoor for telnet/ssh/http/https. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.17 | ScalarradCurCfgAuthenSecondString | read-only | current | The second RADIUS authentication string. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.18 | ScalarradNewCfgAuthenSecondString | read-write | current | The second RADIUS authentication string. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.19 | ScalarradCurCfgSecBd | read-only | current | Enable or disable RADIUS secure backdoor for telnet. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.20 | ScalarradNewCfgSecBd | read-write | current | Enable or disable RADIUS secure backdoor for telnet. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.25 | ScalarradCurCfgSrcLoopIf | read-only | current | The index of the loopback interface that should be used for the source IP of the Radius message; 0 means that no loopback interface is used as the source of th… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.3.26 | ScalarradNewCfgSrcLoopIf | read-write | current | The index of the loopback interface that should be used for the source IP of the Radius message; 0 means that no loopback interface is used as the source of th… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.4 | NodeagNTP | |||
| 1.3.6.1.4.1.26543.2.7.7.1.1.4.1 | ScalaragCurCfgNTPServer | read-only | current | The NTP Server Address. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.4.2 | ScalaragNewCfgNTPServer | read-write | current | The NTP Server Address. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.4.3 | ScalaragCurCfgNTPResyncInterval | read-only | current | The NTP Server resync interval in minutes. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.4.4 | ScalaragNewCfgNTPResyncInterval | read-write | current | The NTP Server resync interval in minutes. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.4.9 | ScalaragCurCfgNTPService | read-only | current | Enable/disable NTP Service. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.4.10 | ScalaragNewCfgNTPService | read-write | current | Enable/disable NTP Service. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.4.11 | ScalaragCurCfgNTPSecServer | read-only | current | The Secondary NTP Server Address. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.4.12 | ScalaragNewCfgNTPSecServer | read-write | current | The Secondary NTP Server Address. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.4.17 | ScalaragCurCfgNTPSrcLoopIf | read-only | current | The index of the loopback interface that should be used for the source IP of the NTP packet; 0 means that no loopback interface is used as the source of the NT… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.4.18 | ScalaragNewCfgNTPSrcLoopIf | read-write | current | The index of the loopback interface that should be used for the source IP of the NTP packet; 0 means that no loopback interface is used as the source of the NT… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5 | NodeagSyslog | |||
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.1 | ScalaragCurCfgSyslogHost | read-only | current | The syslog host IP address in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.2 | ScalaragNewCfgSyslogHost | read-write | current | The syslog host IP address in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.3 | ScalaragCurCfgSyslog2Host | read-only | current | The second syslog host IP address in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.4 | ScalaragNewCfgSyslog2Host | read-write | current | The second syslog host IP address in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.5 | ScalaragCurCfgSyslogFac | read-only | current | The facility level of syslog host in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.6 | ScalaragNewCfgSyslogFac | read-write | current | The facility level of syslog host in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.7 | ScalaragCurCfgSyslog2Fac | read-only | current | The facility level of second syslog host in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.8 | ScalaragNewCfgSyslog2Fac | read-write | current | The facility level of second syslog host in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.9 | ScalaragClrSyslogMsgs | read-write | current | Clears all current Syslog messages. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.10 | ScalaragSyslogMsgTableMaxSize | read-only | current | The maximum number of rows in the syslog message table. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.11 | TableagSyslogMsgTable | not-accessible | current | The table of syslog messages. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.11.1 | RowagSyslogMsgTableEntry | not-accessible | current | A syslog message stored on the switch. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.11.1.1 | ColumnagSyslogMsgIndex | read-only | current | The syslog message table index. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.11.1.2 | ColumnagSyslogMessage | read-only | current | The syslog message. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12 | NodeagLog | |||
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.1 | ScalaragNewCfgSyslogTrapConsole | read-write | current | Enable or disable console syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.2 | ScalaragCurCfgSyslogTrapConsole | read-only | current | Enable or disable console syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.3 | ScalaragNewCfgSyslogTrapSystem | read-write | current | Enable or disable system level syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.4 | ScalaragCurCfgSyslogTrapSystem | read-only | current | Enable or disable system level syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.5 | ScalaragNewCfgSyslogTrapMgmt | read-write | current | Enable or disable management(flash, config, login) syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.6 | ScalaragCurCfgSyslogTrapMgmt | read-only | current | Enable or disable management(flash, config, login) syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.7 | ScalaragNewCfgSyslogTrapCli | read-write | current | Enable or disable CLI generated error syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.8 | ScalaragCurCfgSyslogTrapCli | read-only | current | Enable or disable CLI generated error syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.9 | ScalaragNewCfgSyslogTrapStg | read-write | current | Enable or disable spanning tree syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.10 | ScalaragCurCfgSyslogTrapStg | read-only | current | Enable or disable spanning tree syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.11 | ScalaragNewCfgSyslogTrapVlan | read-write | current | Enable or disable VLAN syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.12 | ScalaragCurCfgSyslogTrapVlan | read-only | current | Enable or disable VLAN syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.19 | ScalaragNewCfgSyslogTrapSsh | read-write | current | Enable or disable SSH, RADIUS syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.20 | ScalaragCurCfgSyslogTrapSsh | read-only | current | Enable or disable SSH, RADIUS syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.21 | ScalaragNewCfgSyslogTrapVrrp | read-write | current | Enable or disable VRRP syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.22 | ScalaragCurCfgSyslogTrapVrrp | read-only | current | Enable or disable VRRP syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.23 | ScalaragNewCfgSyslogTrapBgp | read-write | current | Enable or disable BGP syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.24 | ScalaragCurCfgSyslogTrapBgp | read-only | current | Enable or disable BGP syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.25 | ScalaragNewCfgSyslogTrapNtp | read-write | current | Enable or disable NTP syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.26 | ScalaragCurCfgSyslogTrapNtp | read-only | current | Enable or disable NTP syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.31 | ScalaragNewCfgSyslogTrapIp | read-write | current | Enable or disable IP related syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.32 | ScalaragCurCfgSyslogTrapIp | read-only | current | Enable or disable IP related syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.35 | ScalaragNewCfgSyslogTrapWeb | read-write | current | Enable or disable WEBUI related syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.36 | ScalaragCurCfgSyslogTrapWeb | read-only | current | Enable or disable WEBUI related syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.41 | ScalaragNewCfgSyslogTrapOspf | read-write | current | Enable or disable OSPF related syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.42 | ScalaragCurCfgSyslogTrapOspf | read-only | current | Enable or disable OSPF related syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.45 | ScalaragNewCfgSyslogTrapRmon | read-write | current | Enable or disable RMON related syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.46 | ScalaragCurCfgSyslogTrapRmon | read-only | current | Enable or disable RMON related syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.49 | ScalaragNewCfgSyslogTrap8021x | read-write | current | Enable or disable 802.1x related syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.50 | ScalaragCurCfgSyslogTrap8021x | read-only | current | Enable or disable 802.1x related syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.53 | ScalaragNewCfgSyslogTrapCfg | read-write | current | Enable or disable CFG related syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.54 | ScalaragCurCfgSyslogTrapCfg | read-only | current | Enable or disable CFG related syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.55 | ScalaragNewCfgSyslogTrapServer | read-write | current | Enable or disable Server related syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.56 | ScalaragCurCfgSyslogTrapServer | read-only | current | Enable or disable Server related syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.57 | ScalaragNewCfgSyslogTrapDifftrak | read-write | current | Enable or disable Difftrak related syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.58 | ScalaragCurCfgSyslogTrapDifftrak | read-only | current | Enable or disable Difftrak related syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.61 | ScalaragNewCfgSyslogTrapHotlinks | read-write | current | Enable or disable Hot Links related syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.62 | ScalaragCurCfgSyslogTrapHotlinks | read-only | current | Enable or disable Hot Links related syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.63 | ScalaragNewCfgSyslogTrapLldp | read-write | current | Enable or disable LLDP related syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.64 | ScalaragCurCfgSyslogTrapLldp | read-only | current | Enable or disable LLDP related syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.65 | ScalaragNewCfgSyslogTrapAll | read-write | current | Enable or disable all syslog and SNMP traps in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.66 | ScalaragCurCfgSyslogTrapAll | read-only | current | Enable or disable all syslog and SNMP traps, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.67 | ScalaragNewCfgSyslogTrapIpv6 | read-write | current | Enable or disable IPv6 related syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.68 | ScalaragCurCfgSyslogTrapIpv6 | read-only | current | Enable or disable IPv6 related syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.73 | ScalaragNewCfgSyslogTrapFailover | read-write | current | Enable or disable failover related syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.74 | ScalaragCurCfgSyslogTrapFailover | read-only | current | Enable or disable failover related syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.77 | ScalaragNewCfgSyslogTrapLacp | read-write | current | Enable or disable LACP syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.78 | ScalaragCurCfgSyslogTrapLacp | read-only | current | Enable or disable LACP syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.79 | ScalaragNewCfgSyslogTrapLink | read-write | current | Enable or disable all syslog and SNMP traps, in link up/down. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.80 | ScalaragCurCfgSyslogTrapLink | read-only | current | Enable or disable all syslog and SNMP traps, as currently configured in link up/down. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.81 | ScalaragNewCfgSyslogTrapOspfv3 | read-write | current | Enable or disable OSPFv3 related syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.82 | ScalaragCurCfgSyslogTrapOspfv3 | read-only | current | Enable or disable OSPFv3 related syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.89 | ScalaragNewCfgSyslogTrapVm | read-write | current | Enable or disable all VM-related syslog and SNMP traps. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.90 | ScalaragCurCfgSyslogTrapVm | read-only | current | Enable or disable all VM-related syslog and SNMP traps. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.93 | ScalaragNewCfgSyslogTrapCfgchg | read-write | current | Enable or disable configuration change related syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.94 | ScalaragCurCfgSyslogTrapCfgchg | read-only | current | Enable or disable configuration change related syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.95 | ScalaragNewCfgSyslogTrapVlag | read-write | current | Enable or disable Vlag related syslog and SNMP trap. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.96 | ScalaragCurCfgSyslogTrapVlag | read-only | current | Enable or disable Vlag related syslog and SNMP trap. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.99 | ScalaragNewCfgSyslogTrapIgmpGroup | read-write | current | Enable or disable all IGMP GROUP-related syslog and SNMP traps. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.100 | ScalaragCurCfgSyslogTrapIgmpGroup | read-only | current | Enable or disable all IGMP GROUP-related syslog and SNMP traps. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.101 | ScalaragNewCfgSyslogTrapIgmpMrouter | read-write | current | Enable or disable all IGMP MROUTER-related syslog and SNMP traps. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.102 | ScalaragCurCfgSyslogTrapIgmpMrouter | read-only | current | Enable or disable all IGMP MROUTER-related syslog and SNMP traps. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.103 | ScalaragNewCfgSyslogTrapIgmpQuerier | read-write | current | Enable or disable all IGMP QUERIER-related syslog and SNMP traps. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.104 | ScalaragCurCfgSyslogTrapIgmpQuerier | read-only | current | Enable or disable all IGMP QUERIER-related syslog and SNMP traps. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.105 | ScalaragNewCfgSyslogTrapMld | read-write | current | Enable or disable all MLD-related syslog and SNMP traps. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.106 | ScalaragCurCfgSyslogTrapMld | read-only | current | Enable or disable all MLD-related syslog and SNMP traps. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.107 | ScalaragNewCfgSyslogTrapPrivateVlan | read-write | current | Enable or disable all Private VLAN-related syslog and SNMP traps, as configured in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.108 | ScalaragCurCfgSyslogTrapPrivateVlan | read-only | current | Enable or disable all Private VLAN-related syslog and SNMP traps, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.109 | ScalaragNewCfgSyslogTrapSlp | read-write | current | Enable or disable all SLP-related syslog and SNMP traps, as configured in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.110 | ScalaragCurCfgSyslogTrapSlp | read-only | current | Enable or disable all SLP-related syslog and SNMP traps, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.111 | ScalaragNewCfgSyslogTrapNetconf | read-write | current | Enable or disable Netconf syslog and SNMP trap in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.12.112 | ScalaragCurCfgSyslogTrapNetconf | read-only | current | Enable or disable Netconf syslog and SNMP trap, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.13 | ScalaragCurCfgSyslogSev | read-only | current | The severity of syslog host in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.14 | ScalaragNewCfgSyslogSev | read-write | current | The severity of syslog host in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.15 | ScalaragCurCfgSyslog2Sev | read-only | current | The severity of syslog2 host in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.16 | ScalaragNewCfgSyslog2Sev | read-write | current | The severity of syslogs host in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.21 | ScalaragCurCfgSyslogSrcLoopIf | read-only | current | The index of the loopback interface that should be used for the source IP of the syslog message; 0 means that no loopback interface is used as the source of th… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.22 | ScalaragNewCfgSyslogSrcLoopIf | read-write | current | The index of the loopback interface that should be used for the source IP of the syslog message; 0 means that no loopback interface is used as the source of th… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.23 | ScalaragCurCfgSyslogConsoleSev | read-only | current | The severity of syslogs console in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.24 | ScalaragNewCfgSyslogConsoleSev | read-write | current | The severity of syslogs console in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.25 | ScalaragCurCfgSyslogFlashSev | read-only | current | The severity of syslogs flash in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.5.26 | ScalaragNewCfgSyslogFlashSev | read-write | current | The severity of syslogs flash in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.7 | NodeagTransfer | |||
| 1.3.6.1.4.1.26543.2.7.7.1.1.7.1 | ScalaragTransferServer | read-write | current | The FTP/TFTP server IP address or domain name. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.7.2 | ScalaragTransferImage | read-write | current | Whether the image file should be loaded in image1 or image2 in flash. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.7.3 | ScalaragTransferImageFileName | read-write | current | The image file name to be transferred. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.7.4 | ScalaragTransferCfgFileName | read-write | current | The configuration file name. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.7.5 | ScalaragTransferDumpFileName | read-write | current | The core dump file name. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.7.6 | ScalaragTransferAction | read-write | current | This is an action object to perform various FTP/TFTP Get or Put functions. The FTP/TFTP sever is specified in agTransferServer object. img-get(2) - Download sw… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.7.7 | ScalaragTransferLastActionStatus | read-only | current | The recorded status of the previous FTP/TFTP activity. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.7.9 | ScalaragTransferUserName | read-write | current | The username for the FTP server or blank for TFTP server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.7.10 | ScalaragTransferPassword | read-write | current | The password for the FTP server. For security reason, an empty string will be returned when the OID is read. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.7.11 | ScalaragTransferTSDumpFileName | read-write | current | The TS dump file name. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.7.14 | ScalaragTransferLastConfigurationActionStatus | read-only | current | The status of the last configuration action using the file ftp/tftp'd from server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.7.15 | ScalaragTransferCaFileName | read-write | current | The CA certificate file name. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.7.16 | ScalaragTransferHostCertFileName | read-write | current | The Host certificate file name. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.7.17 | ScalaragTransferHostKeyFileName | read-write | current | The Host private key file name. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.7.18 | ScalaragTransferProtocol | read-write | current | The protocol used by this transfer. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.7.19 | ScalaragServerPort | read-write | current | The port is listened on the server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.7.21 | ScalaragTransferPublicKeyUserName | read-write | current | The user of the public key file. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.7.22 | ScalaragTransferPublicKeyFileName | read-write | current | The client pulic key file name. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.8 | NodeagApply | |||
| 1.3.6.1.4.1.26543.2.7.7.1.1.8.1 | ScalaragApplyPending | read-only | current | This object, when read, gives the user information whether an apply action is needed and that the configuration has been chaged by the user actions. The user t… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.8.2 | ScalaragApplyConfig | read-write | current | When this object is read the current state is returned. idle(2) indicates that there is no apply in progess. complete(4) indicates that the last apply operatio… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.8.4 | ScalaragApplyTableSize | read-only | current | The number of strings in the apply table. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.8.5 | TableagApplyTable | not-accessible | current | The table of failure reasons for an apply of current configuration block changes. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.8.5.1 | RowagApplyTableEntry | not-accessible | current | A row in the table of failure reasons for an apply (information about a particular reason of failure). |
| 1.3.6.1.4.1.26543.2.7.7.1.1.8.5.1.1 | ColumnagApplyIndex | read-only | current | The table index. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.8.5.1.2 | ColumnagApplyString | read-only | current | A string in the apply table. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11 | NodeagTacacsConfig | |||
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.1 | ScalartacCurCfgPrimaryServer | read-only | current | The Hostname of the Primary TACACS+ server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.2 | ScalartacNewCfgPrimaryServer | read-write | current | The Hostname of the Primary TACACS+ server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.3 | ScalartacCurCfgSecondaryServer | read-only | current | The Hostname of the Secondary TACACS+ server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.4 | ScalartacNewCfgSecondaryServer | read-write | current | The Hostname of the Secondary TACACS+ server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.5 | ScalartacCurCfgPort | read-only | current | Specify the TACACS+ port number. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.6 | ScalartacNewCfgPort | read-write | current | Specify the TACACS+ port number. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.7 | ScalartacCurCfgTimeout | read-only | current | The maximum number of seconds before resending authentication to TACACS+ server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.8 | ScalartacNewCfgTimeout | read-write | current | The maximum number of seconds before resending authentication to TACACS+ server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.9 | ScalartacCurCfgRetries | read-only | current | Number of retries to the TACACS+ server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.10 | ScalartacNewCfgRetries | read-write | current | Number of retries to the TACACS+ server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.11 | ScalartacCurCfgState | read-only | current | Enable or disable TACACS+ authentication. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.12 | ScalartacNewCfgState | read-write | current | Enable or disable TACACS+ authentication. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.13 | ScalartacCurCfgAuthenString | read-only | current | The TACACS+ authentication string. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.14 | ScalartacNewCfgAuthenString | read-write | current | The TACACS+ authentication string. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.15 | ScalartacCurCfgBackdoor | read-only | current | Enable or disable TACACS+ backdoor for telnet/ssh/http/https. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.16 | ScalartacNewCfgBackdoor | read-write | current | Enable or disable TACACS+ backdoor for telnet/ssh/http/https. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.17 | ScalartacCurCfgAuthenSecondString | read-only | current | The second TACACS+ authentication string. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.18 | ScalartacNewCfgAuthenSecondString | read-write | current | The second TACACS+ authentication string. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.19 | ScalartacCurCfgCmdAuthor | read-only | current | Enable or disable TACACS+ command authorization. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.20 | ScalartacNewCfgCmdAuthor | read-write | current | Enable or disable TACACS+ command authorization. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.21 | ScalartacCurCfgCmdLogging | read-only | current | Enable or disable TACACS+ command logging. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.22 | ScalartacNewCfgCmdLogging | read-write | current | Enable or disable TACACS+ command logging. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.23 | ScalartacCurCfgSecBd | read-only | current | Enable or disable TACACS+ secure backdoor for telnet. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.24 | ScalartacNewCfgSecBd | read-write | current | Enable or disable TACACS+ secure backdoor for telnet. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.25 | ScalartacCurCfgCmap | read-only | current | Enable/Disable Tacacs+ new privilege level mapping, as configured in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.26 | ScalartacNewCfgCmap | read-write | current | Enable/Disable Tacacs+ new privilege level mapping. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.29 | ScalartacCurCfgEnaPassChange | read-only | current | Enable/Disable Tacacs+ password change. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.30 | ScalartacNewCfgEnaPassChange | read-write | current | Enable/Disable Tacacs+ password change. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.31 | ScalartacChangePassForUser | read-write | current | The username for changing server password. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.32 | ScalartacChangePassCurPass | read-only | current | The current password for tacacs server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.33 | ScalartacChangePassNewPass | read-write | current | The new password for tacacs server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.34 | ScalartacChangePassForServer | read-write | current | Change password for <1/2> Tacacs+ server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.39 | TableagTacacsUserMapCurCfgTable | not-accessible | current | The table of tacacs+ user map current configuration. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.39.1 | RowagTacacsUserMapCurCfgTableEntry | not-accessible | current | A row in the tacacs+ user mapping table. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.39.1.1 | ColumnagTacacsUserMapCurCfgUId | read-only | current | The current config remote privilege identifier. The identifier value corresponds to the remote privilege. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.39.1.2 | ColumnagTacacsUserMapCurCfgMapping | read-only | current | Current Tacacs+ user privilege mappings. The correspondence between the local privilege and the remote privilege is: - The remote privilege is the privilege id… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.40 | TableagTacacsUserMapNewCfgTable | not-accessible | current | The table of tacacs+ user map new configuration. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.40.1 | RowagTacacsUserMapNewCfgTableEntry | not-accessible | current | A row in the tacacs+ user mapping table. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.40.1.1 | ColumnagTacacsUserMapNewCfgUId | read-only | current | The new config remote privilege identifier. The identifier value corresponds to the remote privilege. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.40.1.2 | ColumnagTacacsUserMapNewCfgMapping | read-create | current | Set new Tacacs+ user privilege mappings. The correspondence between the local privilege and the remote privilege is: - The remote privilege is the privilege id… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.41 | ScalartacNewCfgDirectedRequest | read-write | current | Enable/Disable tacacs directed request. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.42 | ScalartacCurCfgDirectedRequest | read-only | current | The current tacacs directed request state. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.43 | ScalartacCurCfgAttempts | read-only | current | Number of login attempts to the TACACS+ server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.44 | ScalartacNewCfgAttempts | read-write | current | Number of login attempts to the TACACS+ server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.45 | ScalartacCurBypassEnable | read-only | current | Status of the enable bypass.If the status of this object is enabled, user authenticated via TACACS+ with admin previllage is granted enable previllage access.I… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.46 | ScalartacNewBypassEnable | read-write | current | Status of the enable bypass.If the status of this object is enabled, user authenticated via TACACS+ with admin previllage is granted enable previllage access.I… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.47 | ScalartacCurCfgEnableAccounting | read-only | current | Current TACACS+ accounting state. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.48 | ScalartacNewCfgEnableAccounting | read-write | current | Enable/Disable TACACS+ accounting. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.49 | ScalartacCurCfgSrcLoopIf | read-only | current | The index of the loopback interface that should be used for the source IP of the Tacacs+ message; 0 means that no loopback interface is used as the source of t… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.11.50 | ScalartacNewCfgSrcLoopIf | read-write | current | The index of the loopback interface that should be used for the source IP of the Tacacs+ message; 0 means that no loopback interface is used as the source of t… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.12 | NodeagMgmtNetConfig | |||
| 1.3.6.1.4.1.26543.2.7.7.1.1.12.1 | ScalaragMgmtNetTableMaxSize | read-only | current | The maximum number of entries in the Management Network Table. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.12.2 | TableagCurCfgMgmtNetTable | not-accessible | current | The table for Management Network definitions in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.12.2.1 | RowagCurCfgMgmtNetEntry | not-accessible | current | A row in the management network definition table. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.12.2.1.1 | ColumnagCurCfgMgmtNetIndex | read-only | current | The index of the Management Network Definition table. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.12.2.1.2 | ColumnagCurCfgMgmtNetSubnet | read-only | current | The Management Network Address in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.12.2.1.3 | ColumnagCurCfgMgmtNetMask | read-only | current | The Management Network Mask/Prefix Length in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.12.3 | TableagNewCfgMgmtNetTable | not-accessible | current | The table for Management Network definitions in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.12.3.1 | RowagNewCfgMgmtNetEntry | not-accessible | current | A row in the management network definition table. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.12.3.1.1 | ColumnagNewCfgMgmtNetIndex | read-only | current | The index of the Management Network Definition table. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.12.3.1.2 | ColumnagNewCfgMgmtNetSubnet | read-create | current | The Management Network Address in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.12.3.1.3 | ColumnagNewCfgMgmtNetMask | read-create | current | The Management Network Mask/Prefix length in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.12.3.1.4 | ColumnagNewCfgMgmtNetDelete | read-create | current | By setting the value to delete(2), the entire row is deleted. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.12.4 | ScalaragMgmtNetClear | read-write | current | By setting the value to delete(2), the entire table is cleared. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.13 | NodeagBoot | |||
| 1.3.6.1.4.1.26543.2.7.7.1.1.13.1 | ScalaragCfgBootResetParameters | read-write | current | String formatated as 'weekday hour minute' where - weekday is none(0),sunday(1),monday(2), tuesday(3),wednesday(4),thursday(5),friday(6), saturday(7) - hour is… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.13.4 | ScalaragCfgBootReset | read-write | current | Cancel pending switch reset. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.13.5 | ScalaragCfgBootNxtResetTime | read-only | current | Display the next scheduled reboot time. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.13.6 | ScalaragCfgBootPendingReset | read-only | current | Shows if there is any pending reboot scheduled. You should cancel any pending reboot scheduled before setting another. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19 | NodeagAccess | |||
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.1 | ScalaragAccessUserMaxUserID | read-only | current | The maximum number of User IDs. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.2 | TableagAccessUserCurCfgTable | not-accessible | current | The table of Access user configuration. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.2.1 | RowagAccessUserCurCfgTableEntry | not-accessible | current | A row in the Access user configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.2.1.1 | ColumnagAccessUserCurCfgUId | read-only | current | The User identifier. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.2.1.2 | ColumnagAccessUserCurCos | read-only | current | The user class of service. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.2.1.3 | ColumnagAccessUserCurCfgName | read-only | current | The user name. Please note, the max length is 8 in stacking mode. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.2.1.4 | ColumnagAccessUserCurCfgPswd | read-only | current | The character string representing the user password. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.2.1.6 | ColumnagAccessUserCurCfgState | read-only | current | User validation (enabled or disabled) in current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.3 | TableagAccessUserNewCfgTable | not-accessible | current | The table of Access user configuration. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.3.1 | RowagAccessUserNewCfgTableEntry | not-accessible | current | A row in the Access user configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.3.1.1 | ColumnagAccessUserNewCfgUId | read-only | current | The User identifier. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.3.1.2 | ColumnagAccessUserNewCos | read-create | current | The user class of service. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.3.1.3 | ColumnagAccessUserNewCfgName | read-create | current | The user name. Please note, the max length is 8 in stacking mode. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.3.1.4 | ColumnagAccessUserNewCfgPswd | read-create | current | The character string representing the user password. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.3.1.7 | ColumnagAccessUserNewCfgState | read-create | current | User validation (enabled or disabled) in new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.3.1.8 | ColumnagAccessUserNewCfgDelete | read-create | current | This is an action object to create or delete a User. other(1) is returned always when read. The following values are writable: delete(2)...to delete a User |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.4 | ScalaragAccessCurStrongPassword | read-only | current | Status of strong password. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.5 | ScalaragAccessNewStrongPassword | read-write | current | Setting this value to enabled(1) enables strong password support, while disabled(0) disables it. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.6 | ScalaragAccessCurStrongPassValidity | read-only | current | Password validity in days. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.7 | ScalaragAccessNewStrongPassValidity | read-write | current | Get or set password validity in days. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.8 | ScalaragAccessCurStrongPassWarning | read-only | current | Warning days before password expires. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.9 | ScalaragAccessNewStrongPassWarning | read-write | current | Get or set warning days before password expires. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.10 | ScalaragAccessCurStrongPassFailLog | read-only | current | Number of failed logins that trigger security notifications. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.11 | ScalaragAccessNewStrongPassFailLog | read-write | current | Get or set number of failed logins that trigger security notifications. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.12 | ScalaragAccessCurDefaultAdmin | read-only | current | Get default admin account state. (1) indicates enabled and (0) indicates disabled (0). Default it is enabled. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.13 | ScalaragAccessNewDefaultAdmin | read-write | current | Setting this value to enabled (1) will enable the default admin account while disabled (0) will disable the default admin account. Default it is enabled. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.14 | ScalaragAccessCurStrongPassLockout | read-only | current | Status of Lockout |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.15 | ScalaragAccessNewStrongPassLockout | read-write | current | Setting this value to enabled (1) enables account locking after trying for failed login attempts. While disabled (0) disables account locking. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.16 | ScalaragAccessCurStrongPassAttemptsMaxFail | read-only | current | The max number of failed logins before disabling account. Default value is 6 |
| 1.3.6.1.4.1.26543.2.7.7.1.1.19.17 | ScalaragAccessNewStrongPassAttemptsMaxFail | read-write | current | Sets Max number of failed logins before disabling account. Default value is 6 |
| 1.3.6.1.4.1.26543.2.7.7.1.1.21 | NodeagLdapConfig | |||
| 1.3.6.1.4.1.26543.2.7.7.1.1.21.1 | ScalarldapCurCfgPrimaryIpAddr | read-only | current | The IP address of the Primary LDAP server,it can be an ipv4 or ipv6 address. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.21.2 | ScalarldapNewCfgPrimaryIpAddr | read-write | current | The IP address of the Primary LDAP server,it can be an ipv4 or ipv6 address. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.21.3 | ScalarldapCurCfgSecondaryIpAddr | read-only | current | The IP address of the Secondary LDAP server,it can be an ipv4 or ipv6 address. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.21.4 | ScalarldapNewCfgSecondaryIpAddr | read-write | current | The IP address of the Secondary LDAP server,it can be an ipv4 or ipv6 address. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.21.5 | ScalarldapCurCfgPort | read-only | current | Specify the LDAP port number. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.21.6 | ScalarldapNewCfgPort | read-write | current | Specify the LDAP port number. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.21.7 | ScalarldapCurCfgRetries | read-only | current | Number of retries to the LDAP server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.21.8 | ScalarldapNewCfgRetries | read-write | current | Number of retries to the LDAP server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.21.9 | ScalarldapCurCfgTimeout | read-only | current | The maximum number of seconds before resending authentication to LDAP server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.21.10 | ScalarldapNewCfgTimeout | read-write | current | The maximum number of seconds before resending authentication to LDAP server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.21.11 | ScalarldapCurCfgDomain | read-only | current | The LDAP domain name. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.21.12 | ScalarldapNewCfgDomain | read-write | current | The LDAP domain name. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.21.13 | ScalarldapCurCfgBackdoor | read-only | current | Enable or disable LDAP backdoor for telnet/ssh/http/https. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.21.14 | ScalarldapNewCfgBackdoor | read-write | current | Enable or disable LDAP backdoor for telnet/ssh/http/https. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.21.15 | ScalarldapCurCfgState | read-only | current | Enable or disable LDAP authentication. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.21.16 | ScalarldapNewCfgState | read-write | current | Enable or disable LDAP authentication. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.21.21 | ScalarldapCurCfgUserNameAttribute | read-only | current | The LDAP username attribute. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.21.22 | ScalarldapNewCfgUserNameAttribute | read-write | current | The LDAP username attribute (default = uid). |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22 | NodeagSSHConfig | |||
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.3 | ScalarsshCurCfgScpAdm | read-only | current | SCP-only admin password. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.4 | ScalarsshNewCfgScpAdm | read-write | current | Set SCP-only admin password. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.5 | ScalarsshNewCfgHKeyGen | read-write | current | This is an action object to generate the RSA host key. other(2) is returned always when read. The following values are writable: generate(1).. Generate the RSA… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.7 | ScalarsshCurCfgSSHPort | read-only | current | SSH server port number. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.8 | ScalarsshNewCfgSSHPort | read-write | current | Set SSH server port number. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.9 | ScalarsshCurCfgScpApplySave | read-only | current | SCP apply and save. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.10 | ScalarsshNewCfgScpApplySave | read-write | current | Enable/Disable the SCP apply and save. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.11 | ScalarsshCurCfgStatus | read-only | current | SSH server status. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.12 | ScalarsshNewCfgStatus | read-write | current | Turn SSH server ON/OFF. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.13 | ScalarsshPubKeyRemAll | read-write | current | Remove all the public key entries on switch. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.14 | ScalarsshPubKeyRemUser | read-write | current | Remove a specific username from the public key database. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.15 | TablesshPubKeyConfigTable | not-accessible | current | The table for ssh public keys and its users. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.15.1 | RowsshPubKeyConfigEntry | not-accessible | current | A row in the ssh public keys tables. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.15.1.1 | ColumnsshPubKeyConfigIndex | read-only | current | The index of the ssh public key entry. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.15.1.2 | ColumnsshPubKeyType | read-only | current | Specify the type of the public key. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.15.1.3 | ColumnsshPubKeyHashValue | read-only | current | The hash value of a specific public key. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.15.1.4 | ColumnsshPubkeyUserBmap | read-only | current | The user list in the key entry. The user are presented in bitmap format. as follows: OCTET 1 OCTET 2 OCTET 3 OCTET 4 xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx ||… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.15.1.5 | ColumnsshPubKeyAddUser | read-write | current | Add a new user to a particular public key. Reminder: The user must be a valid system user. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.15.1.6 | ColumnsshPubKeyDelUser | read-write | current | Remove a user from the user list of the public key entry. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.15.1.7 | ColumnsshPubKeyRemEntry | read-write | current | Remove a public key entry. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.16 | ScalarsshCurCfgSSHAttempts | read-only | current | SSH server maximum authentication attempts. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.22.17 | ScalarsshNewCfgSSHAttempts | read-write | current | Set SSH server maximum authentication attempts. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.24 | NodeagsFlowConfig | |||
| 1.3.6.1.4.1.26543.2.7.7.1.1.24.1 | ScalarsflowCurCfgServerAddress | read-only | current | The IP address of the sFlow server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.24.2 | ScalarsflowNewCfgServerAddress | read-write | current | The IP address of the sFlow server. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.24.3 | ScalarsflowCurCfgServerPort | read-only | current | Specify the sFlow server port number. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.24.4 | ScalarsflowNewCfgServerPort | read-write | current | Specify the sFlow server port number. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.24.5 | ScalarsflowCurCfgState | read-only | current | Enable or disable sFlow. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.24.6 | ScalarsflowNewCfgState | read-write | current | Enable or disable sFlow |
| 1.3.6.1.4.1.26543.2.7.7.1.1.24.7 | TablesflowCurPortCfgTable | not-accessible | current | The table of sFlow port configuration. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.24.7.1 | RowsflowCurPortCfgTableEntry | not-accessible | current | A row in the sFlow port configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.24.7.1.1 | ColumnsflowCurPortCfgTableId | read-only | current | sFlow port number. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.24.7.1.2 | ColumnsflowCurPortSampling | read-only | current | The current sFlow port sampling rate. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.24.7.1.3 | ColumnsflowCurPortPolling | read-only | current | The current sFlow port polling interval. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.24.8 | TablesflowNewPortCfgTable | not-accessible | current | The table of sFlow port configuration. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.24.8.1 | RowsflowNewPortCfgTableEntry | not-accessible | current | A row in the sFlow port configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.24.8.1.1 | ColumnsflowNewPortCfgTableId | read-only | current | sFlow port number. |
| 1.3.6.1.4.1.26543.2.7.7.1.1.24.8.1.2 | ColumnsflowNewPortSampling | read-write | current | The new sFlow port sampling rate. Valid range: 256-65536| 0 for disable |
| 1.3.6.1.4.1.26543.2.7.7.1.1.24.8.1.3 | ColumnsflowNewPortPolling | read-write | current | The new sFlow port polling interval. Valid range: 5-60| 0 for disable |
| 1.3.6.1.4.1.26543.2.7.7.1.1.25 | NodeagUSBCopy | |||
| 1.3.6.1.4.1.26543.2.7.7.1.1.25.1 | ScalaragUSBoperation | read-write | current | Set operation: fromUSB(1): from USB to Flash toUSB(2): from Flash to USB |
| 1.3.6.1.4.1.26543.2.7.7.1.1.25.2 | ScalaragUSBfile | read-write | current | USB filename (to copy from or to copy to) |
| 1.3.6.1.4.1.26543.2.7.7.1.1.25.3 | ScalaragUSBflashFile | read-write | current | Set flash file involved (boot image, image 1, active configuration, syslog, crashdump). Syslog and crashdump can only be copied to USB. (it is forbidden to cop… |
| 1.3.6.1.4.1.26543.2.7.7.1.1.25.4 | ScalaragUSBcopyFile | read-write | current | When this object is read the current state is returned. idle(1) indicates that there is no copy in progess. complete(4) indicates that the last copy operation … |
| 1.3.6.1.4.1.26543.2.7.7.1.1.25.5 | ScalaragUSBresult | read-only | current | Last USB Copy action result. |
| 1.3.6.1.4.1.26543.2.7.7.1.2 | NodeagentStats | |||
| 1.3.6.1.4.1.26543.2.7.7.1.2.1 | NodepktStats | |||
| 1.3.6.1.4.1.26543.2.7.7.1.2.1.1 | ScalarpktStatsAllocs | read-only | current | Total number of packet allocations from the packet buffer pool by the TCP/IP protocol stack. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.1.2 | ScalarpktStatsFrees | read-only | current | Total number of times the packet buffers are freed(released) to the packet buffer pool by the TCP/IP protocol stack. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.1.3 | ScalarpktStatsAllocFails | read-only | current | Total number of packet allocation failures from the packet buffer pool by the TCP/IP protocol stack. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.1.4 | ScalarpktStatsMediums | read-only | current | Total number of packet allocations with size greater than 128 bytes and less than or equal to 1536 bytes from the packet buffer pool by the TCP/IP protocol sta… |
| 1.3.6.1.4.1.26543.2.7.7.1.2.1.5 | ScalarpktStatsJumbos | read-only | current | Total number of packet allocations with size larger than 1536 bytes from the packet buffer pool by the TCP/IP protocol stack. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.1.6 | ScalarpktStatsSmalls | read-only | current | Total number of packet allocations with size less than or eqaul to 128 bytes from the packet buffer pool by the TCP/IP protocol stack. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.1.7 | ScalarpktStatsMediumsHiWatermark | read-only | current | The highest number of packet allocations with size greater than 128 bytes and less than or equal to 1536 bytes from the packet buffer pool by the TCP/IP protoc… |
| 1.3.6.1.4.1.26543.2.7.7.1.2.1.8 | ScalarpktStatsJumbosHiWatermark | read-only | current | The highest number of packet allocations with size larger than 1536 bytes from the packet buffer pool by the TCP/IP protocol stack. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.1.9 | ScalarpktStatsSmallsHiWatermark | read-only | current | The highest number of packet allocations with size less than or equal to 128 bytes from the packet buffer pool by the TCP/IP protocol stack. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2 | NodempCpuStats | |||
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.1 | ScalarmpCpuStatsUtil1Second | read-only | current | The utilization of MP CPU over 1 second. It shows the percentage. It is deprecated. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.2 | ScalarmpCpuStatsUtil5Seconds | read-only | current | The utilization of MP CPU over 5 seconds. It shows the percentage. It is deprecated. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.3 | ScalarmpCpuStatsUtil1Minute | read-only | current | The utilization of MP CPU over 1 minute. It shows the percentage. It is deprecated. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.5 | TablecpuUtilProcessStatsTable | not-accessible | current | The table of CPU utilization per process statistics. It is deprecated. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.5.1 | RowcpuUtilProcessStatsTableEntry | not-accessible | current | A row in the CPU utilization stats per process table. It is deprecated. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.5.1.1 | ColumnprocessId | read-only | current | The process ID. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.5.1.2 | ColumnprocessName | read-only | current | Process Name. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.5.1.3 | ColumncpuProcessUtil1Sec | read-only | current | The utilization of MP CPU over 1 second. It shows the percentage. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.5.1.4 | ColumncpuProcessUtil5Sec | read-only | current | The utilization of MP CPU over 5 seconds. It shows the percentage. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.5.1.5 | ColumncpuProcessUtil1Min | read-only | current | The utilization of MP CPU over 1 min. It shows the percentage. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.5.1.6 | ColumncpuProcessUtil5Min | read-only | current | The utilization of MP CPU over 5 min. It shows the percentage. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.5.1.7 | ColumnprocessStatus | read-only | current | Process Status |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.6 | ScalarmpCpuStatsUtil5Minutes | read-only | current | The utilization of MP CPU over 5 minutes. It shows the percentage. It is deprecated. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.7 | ScalarmpCpuStatsUtil1SecondRev | read-only | current | The utilization of MP CPU over 1 second. It shows the percentage. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.8 | ScalarmpCpuStatsUtil5SecondsRev | read-only | current | The utilization of MP CPU over 5 seconds. It shows the percentage. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.9 | ScalarmpCpuStatsUtil1MinuteRev | read-only | current | The utilization of MP CPU over 1 minute. It shows the percentage. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.10 | ScalarmpCpuStatsUtil5MinutesRev | read-only | current | The utilization of MP CPU over 5 minutes. It shows the percentage. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.11 | TablecpuUtilProcessStatsRevTable | not-accessible | current | The table of CPU utilization per process statistics. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.11.1 | RowcpuUtilProcessStatsRevTableEntry | not-accessible | current | A row in the CPU utilization stats per process table. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.11.1.1 | ColumnprocessIdRev | read-only | current | The process ID. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.11.1.2 | ColumnprocessNameRev | read-only | current | Process Name. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.11.1.3 | ColumncpuProcessUtil1SecRev | read-only | current | The utilization of MP CPU over 1 second. It shows the percentage. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.11.1.4 | ColumncpuProcessUtil5SecRev | read-only | current | The utilization of MP CPU over 5 seconds. It shows the percentage. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.11.1.5 | ColumncpuProcessUtil1MinRev | read-only | current | The utilization of MP CPU over 1 min. It shows the percentage. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.11.1.6 | ColumncpuProcessUtil5MinRev | read-only | current | The utilization of MP CPU over 5 min. It shows the percentage. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.2.11.1.7 | ColumnprocessStatusRev | read-only | current | Process Status |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3 | NodeportStats | |||
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1 | TableportStatsTable | not-accessible | current | The table of port statistics. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1 | RowportStatsTableEntry | not-accessible | current | A row in the port stats table. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.1 | ColumnportStatsIndx | read-only | current | The port index. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.2 | ColumnportStatsPhyIfInOctets | read-only | current | The total number of octets received on the interface, including framing characters. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.3 | ColumnportStatsPhyIfInUcastPkts | read-only | current | The number of subnetwork-unicast packets delivered to a higher-layer protocol. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.4 | ColumnportStatsPhyIfInNUcastPkts | read-only | current | The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.5 | ColumnportStatsPhyIfInDiscards | read-only | current | The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer pr… |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.6 | ColumnportStatsPhyIfInErrors | read-only | current | The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.7 | ColumnportStatsPhyIfInUnknownProtos | read-only | current | The number of packets received via the interface which were discarded because of an unknown or unsupported protocol. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.8 | ColumnportStatsPhyIfOutOctets | read-only | current | The total number of octets transmitted out of the interface, including framing characters. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.9 | ColumnportStatsPhyIfOutUcastPkts | read-only | current | The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not se… |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.10 | ColumnportStatsPhyIfOutNUcastPkts | read-only | current | The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) addre… |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.11 | ColumnportStatsPhyIfOutDiscards | read-only | current | The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reaso… |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.12 | ColumnportStatsPhyIfOutErrors | read-only | current | The number of outbound packets that could not be transmitted because of errors. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.13 | ColumnportStatsPhyIfOutQLen | read-only | current | The length of the output packet queue (in packets). |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.14 | ColumnportStatsPhyIfInBroadcastPkts | read-only | current | The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.15 | ColumnportStatsPhyIfOutBroadcastPkts | read-only | current | The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including … |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.16 | ColumnportStatsClear | read-write | current | Setting this value to clear(2) clears the stats for this port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.17 | ColumnportStatsPhyIfInMulticastPkts | read-only | current | The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.18 | ColumnportStatsPhyIfOutMulticastPkts | read-only | current | The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including … |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.20 | ColumnportStatsLinkStateChange | read-only | current | Number of link state changes. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.21 | ColumnportStatsPhyIfInFctlPkts | read-only | current | The number of inbound flow control packets. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.22 | ColumnportStatsPhyIfOutFctlPkts | read-only | current | The number of outbound flow control packets. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.23 | ColumnportStatsPhyIfInFctlPktsRate | read-only | current | The number of inbound flow control packets per second. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.24 | ColumnportStatsPhyIfOutFctlPktsRate | read-only | current | The number of outbound flow control packets per second. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.25 | ColumnportStatsPhyIfIngDiscdVlan | read-only | current | The number of packets, discarded because of VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.26 | ColumnportStatsPhyIfIngDiscdEgrMap | read-only | current | The number of packets, discarded because of empty egress portmap. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.27 | ColumnportStatsPhyIfIngDiscdFilter | read-only | current | The number of packets, discarded because of filter. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.28 | ColumnportStatsPhyIfIngDiscdPolicy | read-only | current | The number of packets, discarded because of policy. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.29 | ColumnportStatsPhyIfIngDiscdNonFwdStat | read-only | current | The number of packets, discarded because of Non-Forwarding State. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.30 | ColumnportStatsPhyIfIngDiscdIbpCbp | read-only | current | The number of packets discarded because of IBP/CBP. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.31 | ColumnportStatsDot1PortInFrames | read-only | current | The number of IN frames per port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.32 | ColumnportStatsDot1PortOutFrames | read-only | current | The number of OUT frames per port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.33 | ColumnportStatsDot1PortInDiscards | read-only | current | The number of IN packets discarded per port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.34 | ColumnportStatsDot1TpLearnedEntryDiscards | read-only | current | The number of Dot1Tp learned entries discarded. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.35 | ColumnportStatsDot1StpPortForwardTransitions | read-only | current | The number of transitions .... |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.36 | ColumnportStatsPhyIfEgrHOLBlockDiscd | read-only | current | The number of packets, discarded because of HOL Blocking. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.37 | ColumnportStatsPhyIfEgrMMUDiscd | read-only | current | The number of packets, discarded by MMU because of zero port bitmap. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.38 | ColumnportStatsPhyIfEgrCellErrDiscd | read-only | current | The number of packets, discarded because of Cell Errors or purging. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.39 | ColumnportStatsPhyIfEgrMMUAgeDiscd | read-only | current | The number of packets, discarded because of MMU Aging. Applicable in 10/100 mode, incremented for frames aborted which were deferred for an excessive period of… |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.1.1.40 | ColumnportStatsPhyIfEgrOtherDiscd | read-only | current | The number of packets, discarded because of Other reasons. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2 | Tabledot1xPortStatsTable | not-accessible | current | The table of 802.1x port statistics. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1 | Rowdot1xPortStatsTableEntry | not-accessible | current | A row in the 802.1x port stats table. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.1 | Columndot1xPortStatsIndx | read-only | current | The 802.1x port stats index. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.2 | ColumneapolFramesRx | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.3 | ColumneapolFramesTx | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.4 | ColumneapolStartFramesRx | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.5 | ColumneapolLogoffFramesRx | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.6 | ColumneapolRespIdFramesRx | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.7 | ColumneapolRespFramesRx | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.8 | ColumneapolReqIdFramesTx | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.9 | ColumneapolReqFramesTx | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.10 | ColumninvalidEapolFramesRx | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.11 | ColumneapLengthErrorFramesRx | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.12 | ColumnauthEntersConnecting | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.13 | ColumnauthEapLogoffsWhileConnecting | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.14 | ColumnauthEntersAuthenticating | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.15 | ColumnauthSuccessesWhileAuthenticating | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.16 | ColumnauthTimeoutsWhileAuthenticating | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.17 | ColumnauthFailWhileAuthenticating | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.18 | ColumnauthReauthsWhileAuthenticating | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.19 | ColumnauthEapStartsWhileAuthenticating | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.20 | ColumnauthEapLogoffWhileAuthenticating | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.21 | ColumnauthReauthsWhileAuthenticated | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.22 | ColumnauthEapStartsWhileAuthenticated | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.23 | ColumnauthEapLogoffWhileAuthenticated | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.24 | ColumnbackendResponses | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.25 | ColumnbackendAccessChallenges | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.26 | ColumnbackendOtherRequestsToSupplicant | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.27 | ColumnbackendNonNakResponsesFromSupplicant | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.28 | ColumnbackendAuthSuccesses | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.29 | ColumnbackendAuthFails | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.30 | ColumnlastEapolFrameVersion | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.2.1.31 | ColumnlastEapolFrameSource | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4 | TableallportsStatsTable | not-accessible | current | The table of all ports statistics. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1 | RowallportsStatsTableEntry | not-accessible | current | A row in the table of all ports statistics. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.1 | ColumnallportsStatsIndx | read-only | current | The port number. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.2 | ColumnallportsStatsDescr | read-only | current | The port description. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.3 | ColumnallportsStatsSpeed | read-only | current | The current operational speed of the port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.4 | ColumnallportsStatsPhysAddress | read-only | current | The port MAC Address. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.5 | ColumnallportsStatsAdminStatus | read-only | current | The port Admin state. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.6 | ColumnallportsStatsOperStatus | read-only | current | The port Operational Status. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.7 | ColumnallportsStatsInOctets | read-only | current | Octets In for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.8 | ColumnallportsStatsOutOctets | read-only | current | Octets Out for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.9 | ColumnallportsStatsInPkts | read-only | current | Packets In for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.10 | ColumnallportsStatsOutPkts | read-only | current | Packets Out for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.11 | ColumnallportsStatsInUcast | read-only | current | Unicast Packets In for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.12 | ColumnallportsStatsOutUcast | read-only | current | Unicast Packets Out for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.13 | ColumnallportsStatsInBcast | read-only | current | Broadcasts Packets In for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.14 | ColumnallportsStatsOutBcast | read-only | current | Broadcasts Packets Out for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.15 | ColumnallportsStatsInMcast | read-only | current | Multicast Packets In for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.16 | ColumnallportsStatsOutMcast | read-only | current | Multicast Packets Out for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.17 | ColumnallportsStatsInDiscards | read-only | current | Discarded Packets for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.18 | ColumnallportsStatsOutDiscards | read-only | current | Outbound Packets for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.19 | ColumnallportsStatsInErrors | read-only | current | Error Packets for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.20 | ColumnallportsStatsOutErrors | read-only | current | Not sent packets due to error. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.21 | ColumnallportsStatsInUnknownProtos | read-only | current | Unknown protocol packets. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.22 | ColumnallportsStatsOutQLen | read-only | current | Outbound Packet Queue Length. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.23 | ColumnallportsStatsipInReceives | read-only | current | Ip In Receives. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.24 | ColumnallportsStatsipInHeaderErrors | read-only | current | Ip In Header Errors. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.25 | ColumnallportsStatsipInDiscards | read-only | current | Ip In Discards. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.26 | ColumnallportsStatsLinkStateChange | read-only | current | Number of link state changes. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.27 | ColumnallportsStatsipInReceivesRate | read-only | current | Ip In Receives rate. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.28 | ColumnallportsStatsipInHeaderErrorsRate | read-only | current | Ip In Header Errors rate. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.29 | ColumnallportsStatsipInDiscardsRate | read-only | current | Ip In Discards rate. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.30 | ColumnallportsStatsInOctetsRate | read-only | current | Octets In rate for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.31 | ColumnallportsStatsOutOctetsRate | read-only | current | Octets Out rate for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.32 | ColumnallportsStatsInUcastRate | read-only | current | Unicast Packets In rate for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.33 | ColumnallportsStatsOutUcastRate | read-only | current | Unicast Packets Out rate for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.34 | ColumnallportsStatsInBcastRate | read-only | current | Broadcasts Packets In rate for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.35 | ColumnallportsStatsOutBcastRate | read-only | current | Broadcasts Packets Out rate for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.36 | ColumnallportsStatsInMcastRate | read-only | current | Multicast Packets In rate for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.37 | ColumnallportsStatsOutMcastRate | read-only | current | Multicast Packets Out rate for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.38 | ColumnallportsStatsInDiscardsRate | read-only | current | Discarded In Packets rate for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.39 | ColumnallportsStatsOutDiscardsRate | read-only | current | Discarded Out Packets rate for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.40 | ColumnallportsStatsInErrorsRate | read-only | current | Erroneus inbound packets rate for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.4.1.41 | ColumnallportsStatsOutErrorsRate | read-only | current | Not sent packets due to error rate. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.6 | ScalarclearPortsStats | read-write | current | Setting this to clear(2) results in clearing the statistics for all ports. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.7 | Tabledot1RateStatsTable | not-accessible | current | The table of bridging statistics per second. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.7.1 | Rowdot1RateStatsTableEntry | not-accessible | current | Bridging statistics per second. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.7.1.1 | Columndot1RateStatsIndx | read-only | current | The port index. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.7.1.2 | Columndot1RatePortInFrames | read-only | current | The number of frames that have been received per second by this port from its segment. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.7.1.3 | Columndot1RatePortOutFrames | read-only | current | The number of frames that have been transmitted per second by this port to its segment. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.7.1.4 | Columndot1RatePortInDiscards | read-only | current | Count of valid frames received which were discarded per second. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.7.1.5 | Columndot1RateTpLearnedEntryDiscards | read-only | current | The number per second of Forwarding Database entries, which have been or would have been learnt, but have been discarded due to a lack of space to store them. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.7.1.8 | Columndot1RateStpPortForwardTransitions | read-only | current | The number of times this port has transitioned per second from the Learning state to the Forwarding state. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.8 | Tabledot3RateStatsTable | not-accessible | current | The table of Ethernet statistics per second. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.8.1 | Rowdot3RateStatsTableEntry | not-accessible | current | Ethernet statistics per second. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.8.1.1 | Columndot3RateStatsIndx | read-only | current | The port index. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.8.1.2 | Columndot3RateStatsAlignmentErrors | read-only | current | A count of frames received per second on a particular interface that are not an integral number of octets in length and do not pass the FCS check. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.8.1.3 | Columndot3RateStatsFCSErrors | read-only | current | A count of frames received per second on a particular interface that are an integral number of octets in length but do not pass the FCS check. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.8.1.4 | Columndot3RateStatsSingleCollisionFrames | read-only | current | A count of successfully transmitted frames per second on a particular interface for which transmission is inhibited by exactly one collision. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.8.1.5 | Columndot3RateStatsMultipleCollisionFrames | read-only | current | A count of successfully transmitted frames per second on a particular interface for which transmission is inhibited by more than one collision. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.8.1.8 | Columndot3RateStatsLateCollisions | read-only | current | The number of times per second that a collision is detected on a particular interface later than 512 bit-times into the transmission of a packet. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.8.1.9 | Columndot3RateStatsExcessiveCollisions | read-only | current | A count per second of frames for which transmission on a particular interface fails due to excessive collisions. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.8.1.10 | Columndot3RateStatsInternalMacTransmitErrors | read-only | current | A count per second of frames for which transmission on a particular interface fails due to an internal MAC sublayer transmit error. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.8.1.12 | Columndot3RateStatsFrameTooLongs | read-only | current | A count per second of frames received on a particular interface that exceed the maximum permitted frame size. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.8.1.13 | Columndot3RateStatsInternalMacReceiveErrors | read-only | current | A count per second of frames for which reception on a particular interface fails due to an internal MAC sublayer receive error. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.9 | TableportQoSCounterTable | not-accessible | current | The table for QoS counters. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.9.1 | RowportQoSCounterTableEntry | not-accessible | current | A row in the port QoS table. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.9.1.1 | ColumnportQoSIndex | read-only | current | The index of the port |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.9.1.2 | ColumnqueueQoSIndex | read-only | current | The index of the queue per port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.9.1.3 | ColumntxPackets | read-only | current | The total Tx packets. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.9.1.4 | ColumndroppedPackets | read-only | current | The dropped packets. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.9.1.5 | ColumntxBytes | read-only | current | The total Tx bytes. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.9.1.6 | ColumndroppedBytes | read-only | current | The dropped bytes. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.9.1.7 | ColumntxPacketsRate | read-only | current | The Tx packets rate. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.9.1.8 | ColumndroppedPacketsRate | read-only | current | The dropped packets rate. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.9.1.9 | ColumntxBytesRate | read-only | current | The Tx bytes rate. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.3.9.1.10 | ColumndroppedBytesRate | read-only | current | The dropped bytes rate. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.7 | NodeagClearStats | |||
| 1.3.6.1.4.1.26543.2.7.7.1.2.7.1 | ScalarsnmpClearStats | read-write | current | Setting this to clear(2) results in clearing the SNMP statistics. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.9 | NodentpStats | |||
| 1.3.6.1.4.1.26543.2.7.7.1.2.9.1 | ScalarntpPrimaryServerReqSent | read-only | current | The total number of NTP requests sent to Primary NTP Server. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.9.2 | ScalarntpPrimaryServerRespRcvd | read-only | current | The total number of NTP responces received from Primary NTP Server. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.9.3 | ScalarntpPrimaryServerUpdates | read-only | current | The total number of NTP Updates by Primary NTP Server. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.9.4 | ScalarntpSecondaryServerReqSent | read-only | current | The total number of NTP requests sent to Secondary NTP Server. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.9.5 | ScalarntpSecondaryServerRespRcvd | read-only | current | The total number of NTP responces received from Secondary NTP Server. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.9.6 | ScalarntpSecondaryServerUpdates | read-only | current | The total number of NTP Updates by Secondary NTP Server. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.9.7 | ScalarntpLastUpdateServer | read-only | current | The type of ntp server updated last time. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.9.8 | ScalarntpLastUpdateTime | read-only | current | The last time updated by ntp server. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.9.9 | ScalarntpClearStats | read-write | current | Setting this value to clear(2) clears the stats for ntp. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.9.10 | ScalarntpSystemCurrentTime | read-only | current | The current system time. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11 | NodeaclStats | |||
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.1 | TableaclStatsTable | not-accessible | current | The table of ACL statistics. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.1.1 | RowaclStatsTableEntry | not-accessible | current | Statistics about a particular ACL configuration entry. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.1.1.1 | ColumnaclStatsIndex | read-only | current | The acl index. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.1.1.2 | ColumnaclStatsHits | read-only | current | Total number of hits for this ACL entry |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.1.1.3 | ColumnaclClearStats | read-write | current | Setting this value to clear(2) clears the stats for the ACL. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.2 | TablevmapStatsTable | not-accessible | current | The table of VMAP statistics. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.2.1 | RowvmapStatsTableEntry | not-accessible | current | Statistics about a particular VMAP configuration entry. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.2.1.1 | ColumnvmapStatsIndex | read-only | current | The vmap index. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.2.1.2 | ColumnvmapStatsHits | read-only | current | Total number of hits for this VMAP entry |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.2.1.3 | ColumnvmapClearStats | read-write | current | Setting this value to clear(2) clears the stats for the VMAP. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.3 | Tableacl6StatsTable | not-accessible | current | The table of IPv6 ACL statistics. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.3.1 | Rowacl6StatsTableEntry | not-accessible | current | Statistics about a particular IPv6 ACL configuration entry. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.3.1.1 | Columnacl6StatsIndex | read-only | current | The ipv6 acl index. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.3.1.2 | Columnacl6StatsHits | read-only | current | Total number of hits for this IPv6 ACL entry |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.3.1.3 | Columnacl6ClearStats | read-write | current | Setting this value to clear(2) clears the stats for the IPv6 ACL. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.4 | TablemAclStatsTable | not-accessible | current | The table of MACL statistics. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.4.1 | RowmAclStatsTableEntry | not-accessible | current | Statistics about a particular MACL configuration entry. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.4.1.1 | ColumnmAclStatsIndex | read-only | current | The macl index. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.4.1.2 | ColumnmAclStatsHits | read-only | current | Total number of hits for this MACL entry |
| 1.3.6.1.4.1.26543.2.7.7.1.2.11.4.1.3 | ColumnmAclClearStats | read-write | current | Setting this value to clear(2) clears the stats for the MACL. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.12 | NodememoryStats | |||
| 1.3.6.1.4.1.26543.2.7.7.1.2.12.1 | ScalartotalMemoryStats | read-only | current | The total memory in bytes. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.12.2 | ScalarmemoryFreeStats | read-only | current | The free memory in bytes. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.12.3 | ScalarmemorySharedStats | read-only | current | The shared memory in bytes. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.12.4 | ScalarmemoryBufferStats | read-only | current | The buffer memory in bytes. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.12.5 | ScalarswapTotalStats | read-only | current | The total swap memory in bytes. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.12.6 | ScalarswapFreeStats | read-only | current | The free swap memory in bytes. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.12.7 | ScalarhighTotalStats | read-only | current | The total high memory in bytes. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.12.8 | ScalarhighFreeStats | read-only | current | The free high memory in bytes. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20 | NodesnmpStats | |||
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.1 | ScalarnsnmpInPkts | read-only | current | snmpInPkts |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.2 | ScalarnsnmpInBadCommunityNames | read-only | current | snmpInBadCommunityNames |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.3 | ScalarnsnmpInASNParseErrs | read-only | current | snmpInASNParseErrs |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.4 | ScalarnsnmpOutPkts | read-only | current | snmpOutPkts |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.5 | ScalarnsnmpInTooBigs | read-only | current | snmpInTooBigs |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.6 | ScalarnsnmpInBadValues | read-only | current | snmpInBadValues |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.7 | ScalarnsnmpInGenErrs | read-only | current | snmpInGenErrs |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.8 | ScalarnsnmpInTotalSetVars | read-only | current | snmpInTotalSetVars |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.9 | ScalarnsnmpInGetNexts | read-only | current | snmpInGetNexts |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.10 | ScalarnsnmpInGetResponses | read-only | current | snmpInGetResponses |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.11 | ScalarnsnmpOutTooBigs | read-only | current | snmpOutTooBigs |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.12 | ScalarnsnmpOutBadValues | read-only | current | snmpOutBadValues |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.13 | ScalarnsnmpOutGenErrs | read-only | current | snmpOutGenErrs |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.14 | ScalarnsnmpOutGetNexts | read-only | current | snmpOutGetNexts |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.15 | ScalarnsnmpOutGetResponses | read-only | current | snmpOutGetResponses |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.16 | ScalarnsnmpSilentDrops | read-only | current | snmpSilentDrops |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.17 | ScalarnsnmpInBadVersions | read-only | current | snmpInBadVersions |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.18 | ScalarnsnmpInBadCommunityUses | read-only | current | snmpInBadCommunityUses |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.19 | ScalarnsnmpEnableAuthTraps | read-only | current | snmpEnableAuthTraps |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.20 | ScalarnsnmpInBadTypes | read-only | current | snmpInBadTypes |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.21 | ScalarnsnmpInNoSuchNames | read-only | current | snmpInNoSuchNames |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.22 | ScalarnsnmpInReadOnlys | read-only | current | snmpInReadOnlys |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.23 | ScalarnsnmpInTotalReqVars | read-only | current | snmpInTotalReqVars |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.24 | ScalarnsnmpInGetRequests | read-only | current | snmpInGetRequests |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.25 | ScalarnsnmpInSetRequests | read-only | current | snmpInSetRequests |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.26 | ScalarnsnmpInTraps | read-only | current | snmpInTraps |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.27 | ScalarnsnmpOutNoSuchNames | read-only | current | snmpOutNoSuchNames |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.28 | ScalarnsnmpOutReadOnlys | read-only | current | snmpOutReadOnlys |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.29 | ScalarnsnmpOutGetRequests | read-only | current | snmpOutGetRequests |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.30 | ScalarnsnmpOutSetRequests | read-only | current | snmpOutSetRequests |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.31 | ScalarnsnmpOutTraps | read-only | current | snmpOutTraps |
| 1.3.6.1.4.1.26543.2.7.7.1.2.20.32 | ScalarnsnmpProxyDrops | read-only | current | snmpProxyDrops |
| 1.3.6.1.4.1.26543.2.7.7.1.2.21 | NodempTcbStats | |||
| 1.3.6.1.4.1.26543.2.7.7.1.2.21.1 | TabletcpControlBlocksTable | not-accessible | current | All TCP allocated control blocks |
| 1.3.6.1.4.1.26543.2.7.7.1.2.21.1.1 | RowtcpControlBlocksTableEntry | not-accessible | current | A row in the TCP control blocks table. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.21.1.1.1 | ColumntcpControlBlocksIndx | read-only | current | The TCP blocks index. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.21.1.1.2 | ColumndestAddr | read-only | current | The TCP block destination address. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.21.1.1.3 | ColumnremotePort | read-only | current | Tcp informations concerning the remote port |
| 1.3.6.1.4.1.26543.2.7.7.1.2.21.1.1.4 | ColumnsourceAddr | read-only | current | IP address of the source of the Tcp block |
| 1.3.6.1.4.1.26543.2.7.7.1.2.21.1.1.5 | ColumnlocalPort | read-only | current | Tcp informations concerning the local port |
| 1.3.6.1.4.1.26543.2.7.7.1.2.21.1.1.6 | Columnstate | read-only | current | The state of the Tcp |
| 1.3.6.1.4.1.26543.2.7.7.1.2.22 | NodempUdpStats | |||
| 1.3.6.1.4.1.26543.2.7.7.1.2.22.1 | TableudpControlBlocksTable | not-accessible | current | All UDP control blocks in use |
| 1.3.6.1.4.1.26543.2.7.7.1.2.22.1.1 | RowudpControlBlocksTableEntry | not-accessible | current | A row in the UDP control blocks table. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.22.1.1.1 | ColumnudpMpLocalPort | read-only | current | The current UDP local port. |
| 1.3.6.1.4.1.26543.2.7.7.1.2.22.1.1.2 | ColumnudpMpState | read-only | current | The port's state. |
| 1.3.6.1.4.1.26543.2.7.7.1.3 | NodeagentInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.1.3.1 | Nodehardware | |||
| 1.3.6.1.4.1.26543.2.7.7.1.3.1.1 | ScalarhwPartNumber | read-only | current | The hardware part number of the Switch. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.1.2 | ScalarhwRevision | read-only | current | The hardware revision. If the revision is not available, a zero length string should be returned. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.1.11 | ScalarhwMainBoardRevision | read-only | current | The main board revision. If the revision is not available, a zero length string should be returned. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.1.12 | ScalarhwFanStatus | read-only | current | The fan status on the system. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.1.13 | ScalarhwFanSpeed | read-only | current | The fan speed on the system. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.1.14 | ScalarhwTempSensors | read-only | current | The temperature sensors on the system. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.1.15 | ScalarhwGlobalHealthStatus | read-only | current | This variable summarizes the status of several key elements of the device. OK: - When all temperature sensors are below the warning threshold (eg. for Fan rear… |
| 1.3.6.1.4.1.26543.2.7.7.1.3.1.40 | ScalarhwESN | read-only | current | The ESN of the switch. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2 | NodeportInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1 | TableportInfoTable | not-accessible | current | The table of port information. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1 | RowportInfoTableEntry | not-accessible | current | A row in the port information table. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1.1 | ColumnportInfoIndx | read-only | current | The port index. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1.2 | ColumnportInfoSpeed | read-only | current | The current operational speed of the port. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1.3 | ColumnportInfoMode | read-only | current | The current operational mode of the port. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1.4 | ColumnportInfoFlowCtrl | read-only | current | The current operational flow control of the port. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1.5 | ColumnportInfoLink | read-only | current | The current operational link status of the port. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1.6 | ColumnportInfoPhyIfDescr | read-only | current | A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the h… |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1.7 | ColumnportInfoPhyIfType | read-only | current | The type of interface, distinguished according to the physical/link protocol(s) immediately `below' the network layer in the protocol stack. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1.8 | ColumnportInfoPhyIfMtu | read-only | current | The size of the largest datagram which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagr… |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1.9 | ColumnportInfoPhyIfPhysAddress | read-only | current | The interface's address at the protocol layer immediately `below' the network layer in the protocol stack. For interfaces which do not have such an address (e.… |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1.10 | ColumnportInfoPhyIfOperStatus | read-only | current | The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1.11 | ColumnportInfoPhyIfLastChange | read-only | current | The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re- initialization o… |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1.18 | ColumnportInfoLearning | read-only | current | The port L2 (FDB) Learning state. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1.20 | ColumnportInfoBpduGuard | read-only | current | The operational status of BPDU Guard on the port. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1.21 | ColumnportInfoPvid | read-only | current | This is the operational port vlan-id of the port. Typically, the value of this object is the same as the value of the agPortCurCfgPVID object. But if, for exam… |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1.22 | ColumnportInfoVlanTag | read-only | current | This is the operational VLAN tag state of the port. Typically, the value of this object is the same as the value of the agPortCurCfgVlanTag objec. But if, for … |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1.23 | ColumnportInfoErrDisableRecovery | read-only | current | This object indicates whether the system will automatically re-enable an error-disabled port after the time interval indicated by agCurCfgErrDisableTimeout has… |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1.24 | ColumnportInfoErrDisableTimeLeft | read-only | current | If the portInfoErrDisableRecovery object has a value of 'enable' and the portInfoLink object has a value of 'errdisabled', the value of this object indicates t… |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1.25 | ColumnportInfoExtGuard | read-only | current | The operational status of STP Loop/Root Guard on the port. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.2.1.1.26 | ColumnportInfoLFDState | read-only | current | This object indicates whether the port is error-disabled due to excessive link flaps. The value of this object is 'yes' if the port is error-disabled due to ex… |
| 1.3.6.1.4.1.26543.2.7.7.1.3.4 | NodeagDiff | |||
| 1.3.6.1.4.1.26543.2.7.7.1.3.4.2 | ScalaragDiffState | read-write | current | When this object is read the current state is returned. idle(3) indicates that there is no diff in progess. complete(5) indicates that the last diff operation … |
| 1.3.6.1.4.1.26543.2.7.7.1.3.4.3 | ScalaragDiffTableSize | read-only | current | The number of strings in the diff table. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.4.4 | TableagDiffTable | not-accessible | current | The table of diff strings. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.4.4.1 | RowagDiffTableEntry | not-accessible | current | An entry in the diff table. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.4.4.1.1 | ColumnagDiffIndex | read-only | current | The table index. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.4.4.1.2 | ColumnagDiffString | read-only | current | A string in the diff table. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.5 | NodeagCfgDump | |||
| 1.3.6.1.4.1.26543.2.7.7.1.3.5.2 | ScalaragCfgDumpState | read-write | current | When this object is read the current state is returned. idle(2) indicates that there is no dump in progess. complete(4) indicates that the last dump operation … |
| 1.3.6.1.4.1.26543.2.7.7.1.3.5.3 | ScalaragCfgDumpTableSize | read-only | current | The number of strings in the dump table. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.5.4 | TableagCfgDumpTable | not-accessible | current | The table of dump strings. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.5.4.1 | RowagCfgDumpTableEntry | not-accessible | current | An entry in the dump table. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.5.4.1.1 | ColumnagCfgDumpIndex | read-only | current | The table index. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.5.4.1.2 | ColumnagCfgDumpString | read-only | current | A string in the dump table. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.9 | NodegeaportInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.1.3.9.1 | TablegeaportInfoTable | not-accessible | current | The table of gea port mapping. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.9.1.1 | RowgeaportInfoTableEntry | not-accessible | current | An entry in the geaport table mapping. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.9.1.1.1 | ColumngeaportInfoLogicalIndex | read-only | current | The logical port index. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.9.1.1.2 | ColumngeaportInfoAlias | read-only | current | The GEA Port Alias. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.9.1.1.3 | ColumngeaportInfoPort | read-only | current | The GEA Port (0-based). |
| 1.3.6.1.4.1.26543.2.7.7.1.3.9.1.1.4 | ColumngeaportInfoUnit | read-only | current | The GEA Unit. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.11 | NodesfpInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.1.3.11.1 | TablesfpInfoTable | not-accessible | current | The table of external port SFP information. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.11.1.1 | RowsfpInfoTableEntry | not-accessible | current | A row in the external port SFP information table. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.11.1.1.1 | ColumnsfpInfoIndx | read-only | current | The external port SFX index. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.11.1.1.2 | ColumnsfpInfoPort | read-only | current | External Port SFP/XFP alias. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.11.1.1.3 | ColumnsfpInfoDevice | read-only | current | External Port SFP/XFP Device. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.11.1.1.4 | ColumnsfpInfoTXEnable | read-only | current | External Port SFP/XFP TX-Enable. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.11.1.1.5 | ColumnsfpInfoRXSignal | read-only | current | External Port SFP/XFP RX-Signal. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.11.1.1.6 | ColumnsfpInfoTXFault | read-only | current | External Port SFP/XFP TX-Fault. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.11.1.1.7 | ColumnsfpInfoApproved | read-only | current | External Port SFP/XFP Approval. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.11.1.1.8 | ColumnsfpInfoVendor | read-only | current | External Port SFP/XFP device vendor. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.11.1.1.9 | ColumnsfpInfoSerial | read-only | current | External Port SFP/XFP device serial. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.11.1.1.10 | ColumnsfpInfoPartNumber | read-only | current | External Port SFP/XFP device part number. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.11.1.1.11 | ColumnsfpInfoRevision | read-only | current | External Port SFP/XFP device revision. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.11.1.1.12 | ColumnsfpInfoVoltage | read-only | current | External Port SFP/XFP device voltage. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.11.1.1.13 | ColumnsfpInfoTemperature | read-only | current | External Port SFP/XFP device temperature. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.11.1.1.14 | ColumnsfpInfoWaveLength | read-only | current | External Port SFP/XFP device laser wave length. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.12 | NodeagVMGroupInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.1.3.12.1 | TablevmGroupInfoTbl | not-accessible | current | Virtual MAC information table |
| 1.3.6.1.4.1.26543.2.7.7.1.3.12.1.1 | RowvmGroupInfolistEntry | not-accessible | current | The run-time information about a virtual machine |
| 1.3.6.1.4.1.26543.2.7.7.1.3.12.1.1.1 | ColumnvmGroupInfoIdx | read-only | current | Table index, 1 based. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.12.1.1.2 | ColumnvmGroupInfoMac | read-only | current | The virtual machine MAC address. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.12.1.1.3 | ColumnvmGroupInfoIP | read-only | current | The virtual machine IP address. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.12.1.1.4 | ColumnvmGroupInfoPortIdx | read-only | current | System port connected to the virtual machine. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.12.1.1.5 | ColumnvmGroupInfoGroup | read-only | current | The virtual machine group. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.12.1.1.6 | ColumnvmGroupInfoVlan | read-only | current | The virtual machine VLAN |
| 1.3.6.1.4.1.26543.2.7.7.1.3.12.1.1.7 | ColumnvmGroupInfoIsESXSvcCon | read-only | current | Set to 1 if ESX Service Console Interface, else 0. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.12.1.1.8 | ColumnvmGroupInfoIsVMK | read-only | current | Set to 1 if VM Kernel Interface, else 0. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.12.1.1.9 | ColumnvmGroupInfoName | read-only | current | Virtual Machine Name, if available. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.12.1.1.10 | ColumnvmGroupInfoUUID | read-only | current | Virtual Machine UUID, if available. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.12.1.1.11 | ColumnvmGroupInfoVSwitch | read-only | current | Virtual Machine VSwitch, if available. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.12.1.1.12 | ColumnvmGroupInfoPortGroup | read-only | current | Virtual Machine Port Group, if available. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.12.1.1.13 | ColumnvmGroupInfoHost | read-only | current | Virtual Machine Host, if available. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.13 | NodeaccessInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.1.3.13.1 | ScalaraccessInfoClearAllUserFailAttempts | read-write | current | Action Object. When set to clear(2),clears all the unsuccessful attempts of users. Otherwise nothing is done. ok(1) is returned always when read. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.13.2 | ScalaraccessInfoClearAllUserLocks | read-write | current | Action Object. When set to clear(2), Unlock all locked users. Otherwise nothing is done. ok(1) is returned always when read. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.13.3 | TableaccessUserInfoTable | not-accessible | current | The table of user information. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.13.3.1 | RowaccessUserInfoTableEntry | not-accessible | current | An entry in the user information table. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.13.3.1.1 | ColumnaccessUserInfoIndex | read-only | current | The table index. The index value corresponds to the same value of agAccessUserCurCfgUId for the user. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.13.3.1.2 | ColumnaccessUserInfoLockState | read-only | current | Lock State of a specific user, unlocked(1) or locked(2). When the state is locked the user is not allowed to login until the account is unlocked by the adminis… |
| 1.3.6.1.4.1.26543.2.7.7.1.3.13.3.1.3 | ColumnaccessUserInfoClearFailAttempts | read-write | current | Action Object. When set to clear(2), clears the unsuccessful attempts of a particular user. Otherwise nothing is done. ok(1) is returned always when read. |
| 1.3.6.1.4.1.26543.2.7.7.1.3.13.3.1.4 | ColumnaccessUserInfoClearLock | read-write | current | Action Object. When set to clear(2), unlock a particular user. Otherwise nothing is done. ok(1) is returned always when read. |
| 1.3.6.1.4.1.26543.2.7.7.1.4 | NodeagentOper | |||
| 1.3.6.1.4.1.26543.2.7.7.1.4.1 | TableagPortOperTable | not-accessible | current | The table of port operations. |
| 1.3.6.1.4.1.26543.2.7.7.1.4.1.1 | RowagPortOperTableEntry | not-accessible | current | A row in the port operations table. |
| 1.3.6.1.4.1.26543.2.7.7.1.4.1.1.1 | ColumnportOperIdx | read-only | current | The port index. |
| 1.3.6.1.4.1.26543.2.7.7.1.4.1.1.2 | ColumnportOperState | read-write | current | Enable/Disable port. |
| 1.3.6.1.4.1.26543.2.7.7.1.4.1.1.3 | ColumnportOperRmon | read-write | current | Enable/Disable RMON for port. |
| 1.3.6.1.4.1.26543.2.7.7.1.4.1.1.4 | ColumnportOperLearning | read-write | current | Enable/Disable L2 (FDB) Learning for this port. |
| 1.3.6.1.4.1.26543.2.7.7.1.4.2 | NodeagNTPOper | |||
| 1.3.6.1.4.1.26543.2.7.7.1.4.2.1 | ScalarntpOperSendReq | read-write | current | Allows the user to send requests to the NTP server. |
| 1.3.6.1.4.1.26543.2.7.7.1.4.4 | TableportOperDot1xTable | not-accessible | current | The table of port operations. |
| 1.3.6.1.4.1.26543.2.7.7.1.4.4.1 | RowportOperDot1xTableEntry | not-accessible | current | A row in the port 802.1x operation table. |
| 1.3.6.1.4.1.26543.2.7.7.1.4.4.1.1 | ColumnportOperDot1xIndx | read-only | current | The port index. |
| 1.3.6.1.4.1.26543.2.7.7.1.4.4.1.2 | ColumnportOperDot1xReset | read-write | current | Reinitialize 802.1x access control on port. |
| 1.3.6.1.4.1.26543.2.7.7.1.4.4.1.3 | ColumnportOperDot1xReauth | read-write | current | Initiate reauthentication on port. |
| 1.3.6.1.4.1.26543.2.7.7.1.4.5 | NodeagSrvLedOper | |||
| 1.3.6.1.4.1.26543.2.7.7.1.4.5.1 | ScalarsrvLedOper | read-write | current | Enable/disable Service Required LED. |
| 1.3.6.1.4.1.26543.2.7.7.2 | Nodelayer2 | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1 | Nodelayer2Configs | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.1 | Nodevlan | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.1 | ScalarvlanMaxEnt | read-only | current | The maximum number of rows in the VLAN configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.2 | TablevlanCurCfgTable | not-accessible | current | The table of VLAN configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.2.1 | RowvlanCurCfgTableEntry | not-accessible | current | A row in the VLAN configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.2.1.1 | ColumnvlanCurCfgVlanId | read-only | current | The VLAN identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.2.1.2 | ColumnvlanCurCfgPorts | read-only | current | The port list in the VLAN. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || ||… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.2.1.3 | ColumnvlanCurCfgState | read-only | current | Enable or disable a VLAN |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.2.1.5 | ColumnvlanCurCfgStg | read-only | current | The Spanning Tree Group for the VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.2.1.9 | ColumnvlanCurCfgVlanName | read-only | current | The VLAN name. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.2.1.10 | ColumnvlanCurCfgPrVlanType | read-only | current | The type of the Private VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.2.1.11 | ColumnvlanCurCfgPrVlanMapPriId | read-only | current | The primary vlan id |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.3 | TablevlanNewCfgTable | not-accessible | current | The table of VLAN configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.3.1 | RowvlanNewCfgTableEntry | not-accessible | current | A row in the VLAN configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.3.1.1 | ColumnvlanNewCfgVlanId | read-only | current | The VLAN identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.3.1.2 | ColumnvlanNewCfgVlanName | read-create | current | The VLAN name. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.3.1.3 | ColumnvlanNewCfgPorts | read-only | current | The port list in the VLAN. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || ||… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.3.1.4 | ColumnvlanNewCfgState | read-create | current | Enable or disable a VLAN |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.3.1.5 | ColumnvlanNewCfgAddPortIndex | read-create | current | The port to be added to the specified VLAN. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.3.1.6 | ColumnvlanNewCfgRemovePortIndex | read-create | current | The port to be removed from the specified VLAN. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.3.1.7 | ColumnvlanNewCfgDelete | read-create | current | This is an action object to create or delete a VLAN. other(1) is returned always when read. The following values are writable: delete(2)...to delete a VLAN |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.3.1.9 | ColumnvlanNewCfgStg | read-create | current | The Spanning Tree Group for the VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.3.1.13 | ColumnvlanNewCfgPrVlanType | read-write | current | The type of the Private VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.3.1.14 | ColumnvlanNewCfgPrVlanMapPriId | read-write | current | The primary vlan id. To delete set 0. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.4 | ScalarvlanMaxVlanID | read-only | current | The maximum allowed VLAN ID. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.5 | TablepvlanCurCfgTable | not-accessible | current | The table of PROTOCOL VLAN configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.5.1 | RowpvlanCurCfgTableEntry | not-accessible | current | A row in the Protocol VLAN configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.5.1.1 | ColumnpvlanCurCfgVlanId | read-only | current | The VLAN identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.5.1.2 | ColumnpvlanCurCfgPvlanId | read-only | current | The PVLAN identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.5.1.3 | ColumnpvlanCurCfgPvlanFrameType | read-only | current | The frame type of the PVLAN. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.5.1.4 | ColumnpvlanCurCfgPvlanEtherType | read-only | current | The Ether type of the PVLAN. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.5.1.5 | ColumnpvlanCurCfgPvlanPorts | read-only | current | The port list in the PVLAN. The ports are presented in bitmap format. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.5.1.6 | ColumnpvlanCurCfgPvlanPrio | read-only | current | The priority of the PVLAN. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.5.1.7 | ColumnpvlanCurCfgPvlanState | read-only | current | Enable or disable a PVLAN. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.5.1.8 | ColumnpvlanCurCfgPvlanTagPorts | read-only | current | The list of tagged-PVLAN ports. The ports are presented in bitmap format. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.5.1.9 | ColumnpvlanCurCfgPvlanPredefProto | read-only | current | A predefined Protocol (setting EtherType and FrameType to predefined values). |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.6 | TablepvlanNewCfgTable | not-accessible | current | The table of PROTOCOL VLAN configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.6.1 | RowpvlanNewCfgTableEntry | not-accessible | current | A row in the Protocol VLAN configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.6.1.1 | ColumnpvlanNewCfgVlanId | read-only | current | The VLAN identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.6.1.2 | ColumnpvlanNewCfgPvlanId | read-write | current | The PVLAN identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.6.1.3 | ColumnpvlanNewCfgPvlanFrameType | read-write | current | The frame type of the PVLAN. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.6.1.4 | ColumnpvlanNewCfgPvlanEtherType | read-write | current | The Ehter type of the PVLAN. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.6.1.5 | ColumnpvlanNewCfgPvlanAddPortIndex | read-write | current | The port to be added to the specified PVLAN. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.6.1.6 | ColumnpvlanNewCfgPvlanRemovePortIndex | read-write | current | The port to be removed to the specified PVLAN. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.6.1.7 | ColumnpvlanNewCfgPvlanPrio | read-write | current | The priority of the PVLAN. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.6.1.8 | ColumnpvlanNewCfgPvlanState | read-write | current | Enable or disable a PVLAN |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.6.1.9 | ColumnpvlanNewCfgPvlanTagPortIndex | read-write | current | The port to be tagged for the specified PVLAN. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.6.1.10 | ColumnpvlanNewCfgPvlanUntagPortIndex | read-write | current | The port to be untagged for the specified PVLAN. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.6.1.11 | ColumnpvlanNewCfgPvlanPorts | read-only | current | The port list in the PVLAN. The ports are presented in bitmap format. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.6.1.12 | ColumnpvlanNewCfgPvlanTagPorts | read-only | current | The list of tagged-PVLAN ports. The ports are presented in bitmap format. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.6.1.13 | ColumnpvlanNewCfgPvlanDelete | read-write | current | Delete a PVLAN |
| 1.3.6.1.4.1.26543.2.7.7.2.1.1.6.1.14 | ColumnpvlanNewCfgPvlanPredefProto | read-write | current | A predefined Protocol (setting EtherType and FrameType to predefined values). |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2 | Nodetrunkgroup | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.1 | ScalartrunkGroupTableMaxSize | read-only | current | The maximum number of entries in trunk group table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.2 | TabletrunkGroupCurCfgTable | not-accessible | current | The table of trunk group configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.2.1 | RowtrunkGroupCurCfgTableEntry | not-accessible | current | A row in the trunk group configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.2.1.1 | ColumntrunkGroupCurCfgIndex | read-only | current | The identifier of the trunk group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.2.1.2 | ColumntrunkGroupCurCfgPorts | read-only | current | The port list in the trunk group. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 |… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.2.1.3 | ColumntrunkGroupCurCfgState | read-only | current | Enable or disable a trunk group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.3 | TabletrunkGroupNewCfgTable | not-accessible | current | The table of trunk group configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.3.1 | RowtrunkGroupNewCfgTableEntry | not-accessible | current | A row in the trunk group configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.3.1.1 | ColumntrunkGroupNewCfgIndex | read-only | current | The identifier of the trunk group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.3.1.2 | ColumntrunkGroupNewCfgPorts | read-only | current | The port list in the trunk group. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 |… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.3.1.3 | ColumntrunkGroupNewCfgAddPortIndex | read-create | current | The port to be added in the trunk group. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.3.1.4 | ColumntrunkGroupNewCfgRemovePortIndex | read-create | current | The port to be deleted from the trunk group. when read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.3.1.5 | ColumntrunkGroupNewCfgState | read-create | current | Enable or disable a trunk group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.3.1.6 | ColumntrunkGroupNewCfgDelete | read-create | current | Setting the value to delete(2) will delete the entire row. When read, other(1) is returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.4 | ScalartrunkLacpGroupTableMaxSize | read-only | current | The maximum number of entries in LACP trunk group table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.5 | TabletrunkLacpGroupCurCfgTable | not-accessible | current | The table of LACP trunk group configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.5.1 | RowtrunkLacpGroupCurCfgTableEntry | not-accessible | current | A row in the LACP trunk group configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.5.1.1 | ColumntrunkLacpGroupCurCfgIndex | read-only | current | The identifier of the LACP trunk group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.5.1.2 | ColumntrunkLacpGroupCurCfgAdminKey | read-only | current | The administrative key of the LACP trunk group. Ports whose LACP key is same will be member ports of the trunk. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.6 | TabletrunkLacpGroupNewCfgTable | not-accessible | current | The table of LACP trunk group configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.6.1 | RowtrunkLacpGroupNewCfgTableEntry | not-accessible | current | A row in the LACP trunk group configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.6.1.1 | ColumntrunkLacpGroupNewCfgIndex | read-only | current | The identifier of the LACP trunk group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.2.6.1.2 | ColumntrunkLacpGroupNewCfgAdminKey | read-write | current | The administrative key of the LACP trunk group. Ports whose LACP key is same will be member ports of the trunk. Value 0 means LACP trunk group deletion. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3 | NodestgCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.1 | TablestgCurCfgTable | not-accessible | current | The table of Spanning Tree Group configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.1.1 | RowstgCurCfgTableEntry | not-accessible | current | Information about a particular Spanning Tree Group configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.1.1.1 | ColumnstgCurCfgIndex | read-only | current | The identifier of a particular Spanning Tree Group. This is also index to the entLogicalTable of Entity MIB. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.1.1.2 | ColumnstgCurCfgState | read-only | current | Turn on of off Spanning Tree operation of a particular Spanning Tree Group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.1.1.5 | ColumnstgCurCfgPriority | read-only | current | The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.1.1.6 | ColumnstgCurCfgBrgHelloTime | read-only | current | The value in seconds that all bridges use for HelloTime when this bridge is acting as the root. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.1.1.7 | ColumnstgCurCfgBrgForwardDelay | read-only | current | The value in seconds that all bridges use for ForwardDelay when this bridge is acting as the root. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.1.1.8 | ColumnstgCurCfgBrgMaxAge | read-only | current | The value in seconds that all bridges use for MaxAge when this bridge is acting as the root. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.1.1.10 | ColumnstgCurCfgVlanBmap | read-only | current | The vlans applied to the spanning tree group. The vlans are presented in bitmap format. This string displays vlan number from 1 to 4096. in receiving order: OC… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.2 | TablestgNewCfgTable | not-accessible | current | The table of Spanning Tree Groups configuration in the new_config. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.2.1 | RowstgNewCfgTableEntry | not-accessible | current | Information about a particular Spanning Tree Group configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.2.1.1 | ColumnstgNewCfgIndex | read-only | current | The identifier of a particular Spanning Tree Group. This is also index to the entLogicalTable of Entity MIB. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.2.1.2 | ColumnstgNewCfgState | read-write | current | Turn on of off Spanning Tree operation of a particular Spanning Tree Group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.2.1.3 | ColumnstgNewCfgDefaultCfg | read-write | current | Setting the value to default-config(1) will set the default configuration as recommended by IEEE 802.1D for a particular Spanning Tree Group. default-config (1… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.2.1.4 | ColumnstgNewCfgAddVlan | read-write | current | The vlan to be added to the specified Spanning Tree Group. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.2.1.5 | ColumnstgNewCfgRemoveVlan | read-write | current | The vlan to be removed from the specified Spanning Tree Group. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.2.1.8 | ColumnstgNewCfgPriority | read-write | current | The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.2.1.9 | ColumnstgNewCfgBrgHelloTime | read-write | current | The value in seconds that all bridges use for HelloTime when this bridge is acting as the root. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.2.1.10 | ColumnstgNewCfgBrgForwardDelay | read-write | current | The value in seconds that all bridges use for ForwardDelay when this bridge is acting as the root. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.2.1.11 | ColumnstgNewCfgBrgMaxAge | read-write | current | The value in seconds that all bridges use for MaxAge when this bridge is acting as the root. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.2.1.13 | ColumnstgNewCfgVlanBmap | read-only | current | The vlans applied to the spanning tree group. The vlans are presented in bitmap format. This string displays vlan number from 1 to 4096. in receiving order: OC… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.2.1.14 | ColumnstgNewCfgRemoveAllVlan | read-write | current | The all vlans to be removed from the specified Spanning Tree Group. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.3 | TablestgCurCfgPortTable | not-accessible | current | The table of Spanning Tree Group port configuration in the current_config. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.3.1 | RowstgCurCfgPortTableEntry | not-accessible | current | Information about port configuration of a particular Spanning Tree Group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.3.1.1 | ColumnstgCurCfgStgIndex | read-only | current | The identifier of a particular Spanning Tree Group. This is also index to the entLogicalTable of Entity MIB. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.3.1.2 | ColumnstgCurCfgPortIndex | read-only | current | The port identifier of a particular Spanning Tree Group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.3.1.3 | ColumnstgCurCfgPortState | read-only | current | Turn on of off Spanning Tree operation of a particular port of a Spanning Tree Group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.3.1.4 | ColumnstgCurCfgPortPriority | read-only | current | The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.3.1.5 | ColumnstgCurCfgPortPathCost | read-only | current | The contribution of this port to the path cost of paths towards the spanning tree root which include this port ( range is (0..200000000) ). |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.4 | TablestgNewCfgPortTable | not-accessible | current | The table of Spanning Tree Group port configuration in the new_config. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.4.1 | RowstgNewCfgPortTableEntry | not-accessible | current | Information about port configuration of a particular Spanning Tree Group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.4.1.1 | ColumnstgNewCfgStgIndex | read-only | current | The identifier of a particular Spanning Tree Group. This is also index to the entLogicalTable of Entity MIB. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.4.1.2 | ColumnstgNewCfgPortIndex | read-only | current | The port identifier of a particular Spanning Tree Group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.4.1.3 | ColumnstgNewCfgPortState | read-create | current | Turn on of off Spanning Tree operation of a particular port of a Spanning Tree Group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.4.1.4 | ColumnstgNewCfgPortPriority | read-create | current | The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.3.4.1.5 | ColumnstgNewCfgPortPathCost | read-create | current | The contribution of this port to the path cost of paths towards the spanning tree root which include this port ( range is (0..200000000) ). |
| 1.3.6.1.4.1.26543.2.7.7.2.1.4 | Nodemirroring | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.4.1 | NodemirrPortMirr | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.4.1.1 | ScalarpmCurCfgPortMirrState | read-only | current | The state of port-based port mirroring. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.4.1.2 | ScalarpmNewCfgPortMirrState | read-write | current | The state of port-based port mirroring. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.4.1.3 | TablepmCurCfgPortMonitorTable | not-accessible | current | The table of monitoring ports. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.4.1.3.1 | RowpmCurCfgPortMonitorEntry | not-accessible | current | A row in the monitoring port table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.4.1.3.1.1 | ColumnpmCurCfgPmirrMoniPortIndex | read-only | current | The monitoring port number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.4.1.3.1.2 | ColumnpmCurCfgPmirrMirrPortIndex | read-only | current | The mirrored port number |
| 1.3.6.1.4.1.26543.2.7.7.2.1.4.1.3.1.3 | ColumnpmCurCfgPmirrDirection | read-only | current | The type of traffic to be monitored with respect to the mirrored port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.4.1.4 | TablepmNewCfgPortMonitorTable | not-accessible | current | The table of monitoring ports. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.4.1.4.1 | RowpmNewCfgPortMonitorEntry | not-accessible | current | A row in the monitoring port table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.4.1.4.1.1 | ColumnpmNewCfgPmirrMoniPortIndex | read-only | current | The monitoring port number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.4.1.4.1.2 | ColumnpmNewCfgPmirrMirrPortIndex | read-only | current | The mirrored port number |
| 1.3.6.1.4.1.26543.2.7.7.2.1.4.1.4.1.3 | ColumnpmNewCfgPmirrDirection | read-create | current | The type of traffic to be monitored with respect to the mirrored port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.4.1.4.1.4 | ColumnpmNewCfgPmirrDelete | read-create | current | Setting the value to delete(2) will delete the entire row. When read, other(1) is returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.4.1.4.1.10 | ColumnpmNewCfgPmonDelete | read-create | current | Setting the value to delete(2) will delete the monitor port. When read, other(1) is returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5 | Nodelacp | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.1 | ScalarlacpCurSystemPriority | read-only | current | A 2-octet read-write value indicating the priority value associated with the Actor's System ID. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.2 | ScalarlacpNewSystemPriority | read-write | current | A 2-octet read-write value indicating the priority value associated with the Actor's System ID. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.5 | ScalarlacpCurSystemTimeoutTime | read-only | current | If a port does not receive LACPDUs for Timeout time LACP information pertaining to the port is invalidated. Its every 3 sec (short) and every 90 sec (long 3). |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.6 | ScalarlacpNewSystemTimeoutTime | read-write | current | If a port does not receive LACPDUs for Timeout time LACP information pertaining to the port is invalidated. Its every 3 sec (short) and every 90 sec (long 3). |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.7 | TablelacpCurPortCfgTable | not-accessible | current | The table of LACP port configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.7.1 | RowlacpCurPortCfgTableEntry | not-accessible | current | A row in the LACP port configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.7.1.1 | ColumnlacpCurPortCfgTableId | read-only | current | LACP port number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.7.1.2 | ColumnlacpCurPortState | read-only | current | LACP port state can be one of three states off (Not participating in LACP) Active (Initiates LACPDU updates) Passive (Does not initiate LACPDU updates but resp… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.7.1.3 | ColumnlacpCurPortActorPortPriority | read-only | current | The priority value assigned to this Aggregation Port. This 16-bit value is read-only. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.7.1.4 | ColumnlacpCurPortActorAdminKey | read-only | current | The current administrative value of the Key for the Aggregation Port. This is a 16-bit read-only value. The meaning of particular Key values is of local signif… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.7.1.5 | ColumnlacpCurPortActorMinLinks | read-only | current | The current minimum links for the Aggregation Port. This is a 16-bit read-only value. The meaning of particular Key values is of local significance. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.7.1.6 | ColumnlacpCurPortSuspendIndividual | read-only | current | It indicates if the port can be treated as an individual link when it does not get LACPDU from the peer port. suspend (can't be treated as a normal link) indiv… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.8 | TablelacpNewPortCfgTable | not-accessible | current | The table of LACP port configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.8.1 | RowlacpNewPortCfgTableEntry | not-accessible | current | A row in the LACP port configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.8.1.1 | ColumnlacpNewPortCfgTableId | read-only | current | LACP port number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.8.1.2 | ColumnlacpNewPortState | read-write | current | LACP port state can be one of three states off (Not participating in LACP) Active (Initiates LACPDU updates) Passive (Does not initiate LACPDU updates but resp… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.8.1.3 | ColumnlacpNewPortActorPortPriority | read-write | current | The priority value assigned to this Aggregation Port. This 16-bit value is read-write. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.8.1.4 | ColumnlacpNewPortActorAdminKey | read-write | current | The current administrative value of the Key for the Aggregation Port. This is a 16-bit read-write value. The meaning of particular Key values is of local signi… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.8.1.5 | ColumnlacpNewPortActorMinLinks | read-write | current | The current minimum links for the Aggregation Port. This is a 16-bit read-write value. The meaning of particular Key values is of local significance. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.8.1.6 | ColumnlacpNewPortSetToDefault | read-write | current | When read, always returns none(1). When setting setDefault(2) value, the LACP port settings are set to the default values. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.8.1.7 | ColumnlacpNewPortSuspendIndividual | read-write | current | It indicates if the port can be treated as an individual link when it does not get LACPDU from the peer port. suspend (can't be treated as a normal link) indiv… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.9 | ScalarlacpDeleteTrunk | read-write | current | Delete a trunk with specified admin key |
| 1.3.6.1.4.1.26543.2.7.7.2.1.5.10 | ScalarlacpNewSystemSetToDefault | read-write | current | When read, always returns none(1). When setting setDefault(2) value, the LACP system settings are set to the default values. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.6 | Nodethash | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.6.1 | NodethashL2 | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.6.1.1 | Scalarl2ThashCurCfgSmacState | read-only | current | Enable or disable smac hash. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.6.1.2 | Scalarl2ThashNewCfgSmacState | read-write | current | Enable or disable smac hash. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.6.1.3 | Scalarl2ThashCurCfgDmacState | read-only | current | Enable or disable dmac hash. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.6.1.4 | Scalarl2ThashNewCfgDmacState | read-write | current | Enable or disable dmac hash. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.6.1.5 | Scalarl2ThashCurCfgSipState | read-only | current | Enable or disable sip hash. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.6.1.6 | Scalarl2ThashNewCfgSipState | read-write | current | Enable or disable sip hash. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.6.1.7 | Scalarl2ThashCurCfgDipState | read-only | current | Enable or disable dip hash. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.6.1.8 | Scalarl2ThashNewCfgDipState | read-write | current | Enable or disable dip hash. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.6.1.9 | Scalarl2ThashCurCfgIngressState | read-only | current | Enable or disable ingres port hash. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.6.1.10 | Scalarl2ThashNewCfgIngressState | read-write | current | Enable or disable ingres port hash. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.6.1.11 | Scalarl2ThashCurCfgL4PortState | read-only | current | Enable or disable L4 port hash. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.6.1.12 | Scalarl2ThashNewCfgL4PortState | read-write | current | Enable or disable L4 port hash. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7 | NodemstCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.1 | NodemstGeneralCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.1.3 | ScalarmstCurCfgRegionName | read-only | current | The Name for the Region's configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.1.4 | ScalarmstNewCfgRegionName | read-write | current | The Name for the Region's configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.1.5 | ScalarmstCurCfgRegionRevision | read-only | current | Revision of the MST Region. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.1.6 | ScalarmstNewCfgRegionRevision | read-write | current | Revision of the MST Region. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.1.7 | ScalarmstCurCfgMaxHopCount | read-only | current | Indicates the maximum hop count value. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.1.8 | ScalarmstNewCfgMaxHopCount | read-write | current | Indicates the maximum hop count value. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.1.9 | ScalarmstCurCfgStpMode | read-only | current | The version of Spanning Tree Protocal the bridge is currently running. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.1.10 | ScalarmstNewCfgStpMode | read-write | current | The version of Spanning Tree Protocal the bridge is currently running. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2 | NodemstCistCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.1 | ScalarmstCistDefaultCfg | read-write | current | Setting the value to default(1) will set the Multiple Spanning Tree and member parameters to default. default(1) is always returned when read, but it does not … |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.2 | NodemstCistBridgeCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.2.1 | ScalarmstCistCurCfgBridgePriority | read-only | current | The value of the writable portion of the Brigde Identifier comprising of the first two octets. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.2.2 | ScalarmstCistNewCfgBridgePriority | read-write | current | The value of the writable portion of the Brigde Identifier comprising of the first two octets. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.2.5 | ScalarmstCistCurCfgBridgeMaxAge | read-only | current | The value in seconds that all bridges use for MaxAge when this bridge is acting as the root. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.2.6 | ScalarmstCistNewCfgBridgeMaxAge | read-write | current | The value in seconds that all bridges use for MaxAge when this bridge is acting as the root. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.2.7 | ScalarmstCistCurCfgBridgeForwardDelay | read-only | current | The value in seconds that all bridges use for ForwardDelay when this bridge is acting as the root. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.2.8 | ScalarmstCistNewCfgBridgeForwardDelay | read-write | current | The value in seconds that all bridges use for ForwardDelay when this bridge is acting as the root. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.2.9 | ScalarmstCistCurCfgVlanBmap | read-only | current | The vlans applied to the CIST group. The vlans are presented in bitmap format. This string displays vlan number from 1 to 4094. in receiving order: OCTET 1 OCT… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.2.10 | ScalarmstCistNewCfgVlanBmap | read-only | current | The vlans applied to the CIST group. The vlans are presented in bitmap format. This string displays vlan number from 1 to 4094. in receiving order: OCTET 1 OCT… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.2.11 | ScalarmstCistNewCfgAddVlan | read-create | current | The vlan to be added to the CIST Group. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.3 | TablemstCistCurCfgPortTable | not-accessible | current | The table of CIST Port configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.3.1 | RowmstCistCurCfgPortTableEntry | not-accessible | current | Information about a particular CIST Port configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.3.1.1 | ColumnmstCistCurCfgPortIndex | read-only | current | The port number of the port for which this entry contains spanning tree configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.3.1.2 | ColumnmstCistCurCfgPortPriority | read-only | current | The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting this value. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.3.1.3 | ColumnmstCistCurCfgPortPathCost | read-only | current | The contribution of this port to the path cost of paths towards the CIST Root which include this port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.3.1.4 | ColumnmstCistCurCfgPortLinkType | read-only | current | The administrative point-to-point status of the LAN segment attached to this port. A value of p2p (2) indicates that this port should always be treated as if i… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.3.1.5 | ColumnmstCistCurCfgPortEdge | read-only | current | The value of the Edge Port parameter. (for MSTP only) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.3.1.6 | ColumnmstCistCurCfgPortStpState | read-only | current | Turn port's Spanning Tree on/off. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.3.1.7 | ColumnmstCistCurCfgPortHelloTime | read-only | current | The amount of time between the transmission of Configuration Port PDUs in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.3.1.8 | ColumnmstCistCurCfgPortPvstProtection | read-only | current | The value of the PVST Protection parameter. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.4 | TablemstCistNewCfgPortTable | not-accessible | current | The table of CIST Port configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.4.1 | RowmstCistNewCfgPortTableEntry | not-accessible | current | Information about a particular CIST Port configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.4.1.1 | ColumnmstCistNewCfgPortIndex | read-only | current | The port number of the port for which this entry contains spanning tree configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.4.1.2 | ColumnmstCistNewCfgPortPriority | read-write | current | The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting this value. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.4.1.3 | ColumnmstCistNewCfgPortPathCost | read-write | current | The contribution of this port to the path cost of paths towards the CIST Root which include this port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.4.1.6 | ColumnmstCistNewCfgPortStpState | read-write | current | Turn port's Spanning Tree on/off. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.4.1.7 | ColumnmstCistNewCfgPortHelloTime | read-write | current | The amount of time between the transmission of Configuration Port PDUs in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.7.2.4.1.8 | ColumnmstCistNewCfgPortPvstProtection | read-write | current | The value of the PVST Protection parameter. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.8 | Nodel2GeneralCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.8.9 | ScalarpvstCompatibilityCurCfgState | read-only | current | Enable or disable PVST+ compatibility |
| 1.3.6.1.4.1.26543.2.7.7.2.1.8.10 | ScalarpvstCompatibilityNewCfgState | read-write | current | Enable or disable PVST+ compatibility |
| 1.3.6.1.4.1.26543.2.7.7.2.1.8.11 | ScalarnostpCurCfgState | read-only | current | STP Mode Disable global state. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.8.12 | ScalarnostpNewCfgState | read-write | current | Enable or disable STP Mode Disable. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.8.13 | ScalarstpLoopGuardCurCfgState | read-only | current | STP loop guard global state. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.8.14 | ScalarstpLoopGuardNewCfgState | read-write | current | Enable or disable STP loop guard. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.8.15 | ScalarvlanAutoStgCurCfgState | read-only | current | VLAN automatic STG assignment global state. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.8.16 | ScalarvlanAutoStgNewCfgState | read-write | current | Enable or disable VLAN automatic STG assignment. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10 | NodefailoverCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.1 | ScalarfailoverCurCfgOnState | read-only | current | Failover ON/OFF setting. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.2 | ScalarfailoverNewCfgOnState | read-write | current | Failover ON/OFF settings. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.5 | ScalarfailoverMaxTriggerEntries | read-only | current | The maximum number of entries in the Failover Trigger Table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.6 | TablefailoverCurCfgTriggerTable | not-accessible | current | The Failover Trigger Table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.6.1 | RowfailoverCurCfgTriggerTableEntry | not-accessible | current | A row in the Failover Trigger Table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.6.1.1 | ColumnfailoverCurCfgTriggerId | read-only | current | The Trigger identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.6.1.2 | ColumnfailoverCurCfgTriggerState | read-only | current | Enable or disable Trigger state |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.6.1.3 | ColumnfailoverCurCfgTriggerLimit | read-only | current | Limit # of operational links |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.6.1.6 | ColumnfailoverCurCfgTriggerMmonPort | read-only | current | The Manual Monitor port list. The ports are presented in bitmap format: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || … |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.6.1.7 | ColumnfailoverCurCfgTriggerMmonTrunk | read-only | current | The Manual Monitor trunk list. The trunks are presented in bitmap format: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ trunk 8 || || || ||___ trunk 7… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.6.1.8 | ColumnfailoverCurCfgTriggerMmonKey | read-only | current | The LACP admin key. This is an array of 16-bit read-only values. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.6.1.9 | ColumnfailoverCurCfgTriggerMconPort | read-only | current | The Manual Control port list. The ports are presented in bitmap format: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || … |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.6.1.11 | ColumnfailoverCurCfgTriggerMconTrunk | read-only | current | The Manual Control trunk list. The trunks are presented in bitmap format: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ trunk 8 || || || ||___ trunk 7… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.6.1.12 | ColumnfailoverCurCfgTriggerMconKey | read-only | current | The LACP admin key. This is an array of 16-bit read-only values. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7 | TablefailoverNewCfgTriggerTable | not-accessible | current | The Failover Trigger Table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1 | RowfailoverNewCfgTriggerTableEntry | not-accessible | current | A row in the Failover Trigger Table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.1 | ColumnfailoverNewCfgTriggerId | read-only | current | The Trigger identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.2 | ColumnfailoverNewCfgTriggerState | read-write | current | Enable or disable Trigger state |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.3 | ColumnfailoverNewCfgTriggerLimit | read-write | current | Limit # of operational links |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.10 | ColumnfailoverNewCfgTriggerMmonPort | read-only | current | The Manual Monitor port list. The ports are presented in bitmap format: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || … |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.11 | ColumnfailoverNewCfgTriggerMmonPortIndexAdd | read-create | current | Add port to Manual Monitor. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.12 | ColumnfailoverNewCfgTriggerMmonPortIndexRem | read-create | current | Remove port from Manual Monitor. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.13 | ColumnfailoverNewCfgTriggerMmonTrunk | read-only | current | The Manual Monitor trunk list. The trunks are presented in bitmap format: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ trunk 8 || || || ||___ trunk 7… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.14 | ColumnfailoverNewCfgTriggerMmonTrunkAdd | read-create | current | Add trunk to Manual Monitor. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.15 | ColumnfailoverNewCfgTriggerMmonTrunkRem | read-create | current | Remove trunk from Manual Monitor. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.16 | ColumnfailoverNewCfgTriggerMmonKey | read-only | current | The LACP admin key. This is an array of 16-bit read-only values. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.17 | ColumnfailoverNewCfgTriggerMmonKeyAdd | read-create | current | Add LACP admin key to Manual Monitor. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.18 | ColumnfailoverNewCfgTriggerMmonKeyRem | read-create | current | Remove LACP admin key from Manual Monitor. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.19 | ColumnfailoverNewCfgTriggerMconPort | read-only | current | The Manual Control port list. The ports are presented in bitmap format: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || … |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.20 | ColumnfailoverNewCfgTriggerMconPortIndexAdd | read-create | current | Add port to Manual Control. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.21 | ColumnfailoverNewCfgTriggerMconPortIndexRem | read-create | current | Remove port from Manual Control. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.25 | ColumnfailoverNewCfgTriggerMconTrunk | read-only | current | The Manual Control trunk list. The trunks are presented in bitmap format: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ trunk 8 || || || ||___ trunk 7… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.26 | ColumnfailoverNewCfgTriggerMconTrunkAdd | read-create | current | Add trunk to Manual Control. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.27 | ColumnfailoverNewCfgTriggerMconTrunkRem | read-create | current | Remove trunk from Manual Control. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.28 | ColumnfailoverNewCfgTriggerMconKey | read-only | current | The LACP admin key. This is an array of 16-bit read-only values. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.29 | ColumnfailoverNewCfgTriggerMconKeyAdd | read-create | current | Add LACP admin key to Manual Control. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.30 | ColumnfailoverNewCfgTriggerMconKeyRem | read-create | current | Remove LACP admin key from Manual Control. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.10.7.1.31 | ColumnfailoverNewCfgTriggerDelete | read-create | current | Setting the value to delete(2) will delete the entire row. When read, other(1) is returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12 | Nodedot1x | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.1 | Scalardot1xCurStatus | read-only | current | Dot1x status |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.2 | Scalardot1xNewStatus | read-write | current | Dot1x status |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.3 | Tabledot1xCurCfgPortTable | not-accessible | current | The table of 8021x configuration in the Current_config. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.3.1 | Rowdot1xCurCfgPortEntry | not-accessible | current | Information about 8021x Port Config |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.3.1.1 | Columndot1xCurCfgPortIndex | read-only | current | The 8021x Port number for which the table is related. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.3.1.2 | Columndot1xCurCfgPortMode | read-only | current | Port authenticaton mode forceUnauth(0), auto(1), forceAuth(2) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.3.1.3 | Columndot1xCurCfgPortQtPeriod | read-only | current | Quiet period (0-65535) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.3.1.4 | Columndot1xCurCfgPortTxPeriod | read-only | current | Tx Period |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.3.1.5 | Columndot1xCurCfgPortSupTmout | read-only | current | Supplicant timeout (1..65535) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.3.1.6 | Columndot1xCurCfgPortSrvTmout | read-only | current | Server timeout (1..65535) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.3.1.7 | Columndot1xCurCfgPortMaxRq | read-only | current | Maximum numer of requests (1..10) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.3.1.8 | Columndot1xCurCfgPortRaPeriod | read-only | current | Reautentication period (0..604800) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.3.1.9 | Columndot1xCurCfgPortReAuth | read-only | current | ReAuthentication state off(0), on(1) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.3.1.10 | Columndot1xCurCfgPortVlanAssign | read-only | current | Vlan assignment state off(0), on(1) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.4 | Tabledot1xNewCfgPortTable | not-accessible | current | The table of 8021x configuration in the new_config. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.4.1 | Rowdot1xNewCfgPortEntry | not-accessible | current | Information about 8021x Port Config |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.4.1.1 | Columndot1xNewCfgPortIndex | read-only | current | The 8021x Port number for which the table is related. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.4.1.2 | Columndot1xNewCfgPortMode | read-create | current | Port authentication mode forceUnauth(0), auto(1), forceAuth(2) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.4.1.3 | Columndot1xNewCfgPortQtPeriod | read-create | current | Quiet period (0..65535) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.4.1.4 | Columndot1xNewCfgPortTxPeriod | read-create | current | Tx Period (1..65535) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.4.1.5 | Columndot1xNewCfgPortSupTmout | read-create | current | Supplicant Timeout (1..65535) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.4.1.6 | Columndot1xNewCfgPortSrvTmout | read-create | current | Server Timeout (1..65535) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.4.1.7 | Columndot1xNewCfgPortMaxRq | read-create | current | Maximum number of requests (1..10) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.4.1.8 | Columndot1xNewCfgPortRaPeriod | read-create | current | Reauthentication period (1..604800) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.4.1.9 | Columndot1xNewCfgPortReAuth | read-create | current | Reauthentication state off(0), on(1) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.4.1.10 | Columndot1xNewCfgPortDefault | read-create | current | Port default settings |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.4.1.11 | Columndot1xNewCfgPortApplyGlobal | read-create | current | Apply Global config |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.4.1.12 | Columndot1xNewCfgPortVlanAssign | read-create | current | Enable/Disable the assignment of vlan from radius server when the port is successfully autheticated. Vlan assignment state off(0), on(1) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.5 | Nodedot1xCurCfgGlobalTable | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.5.1 | Nodedot1xCurCfgGuestVlan | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.5.1.1 | Scalardot1xCurCfgGuestVlanNumber | read-only | current | 8021.x Guest VLAN number |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.5.1.2 | Scalardot1xCurCfgGuestVlanStatus | read-only | current | 8021.x Guest VLAN status enabled(1), disabled(2) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.5.3 | Scalardot1xCurCfgGlobalMode | read-only | current | Autehtication Mode forceUnauth(0), auto(1), forceAuth(2) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.5.4 | Scalardot1xCurCfgGlobalQtPeriod | read-only | current | Quiet period (0..65535) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.5.5 | Scalardot1xCurCfgGlobalTxPeriod | read-only | current | Tx period (1..65535) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.5.6 | Scalardot1xCurCfgGlobalSupTmout | read-only | current | Supplicant timeout (1..65535) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.5.7 | Scalardot1xCurCfgGlobalSrvTmout | read-only | current | Server timeout (1..65535) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.5.8 | Scalardot1xCurCfgGlobalMaxRq | read-only | current | Maximum number of requests (1..10) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.5.9 | Scalardot1xCurCfgGlobalRaPeriod | read-only | current | Reauthentication period (0..604800) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.5.10 | Scalardot1xCurCfgGlobalReAuth | read-only | current | |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.5.12 | Scalardot1xCurCfgGlobalVlanAssign | read-only | current | Vlan assignment status |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.6 | Nodedot1xNewCfgGlobalTable | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.6.1 | Nodedot1xNewCfgGuestVlan | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.6.1.1 | Scalardot1xNewCfgGuestVlanNumber | read-write | current | 8021.x Guest VLAN number |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.6.1.2 | Scalardot1xNewCfgGuestVlanStatus | read-write | current | 8021.x Guest VLAN status enabled(1), disabled(2) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.6.3 | Scalardot1xNewCfgGlobalMode | read-create | current | Authentication Mode |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.6.4 | Scalardot1xNewCfgGlobalQtPeriod | read-create | current | Quiet Period (0..65535) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.6.5 | Scalardot1xNewCfgGlobalTxPeriod | read-create | current | Tx Period (1..65535) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.6.6 | Scalardot1xNewCfgGlobalSupTmout | read-create | current | Supplicand timeout (1..65535) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.6.7 | Scalardot1xNewCfgGlobalSrvTmout | read-create | current | Server timeout (1..65535) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.6.8 | Scalardot1xNewCfgGlobalMaxRq | read-create | current | Maximum number of requests (1..10) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.6.9 | Scalardot1xNewCfgGlobalRaPeriod | read-create | current | Reauthentication period (1..604800) |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.6.10 | Scalardot1xNewCfgGlobalReAuth | read-create | current | Reauthentication status |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.6.11 | Scalardot1xNewCfgGlobalDefault | read-create | current | Restore default 802.1x configuration |
| 1.3.6.1.4.1.26543.2.7.7.2.1.12.6.12 | Scalardot1xNewCfgGlobalVlanAssign | read-create | current | Enable/Disable the assignment of vlan from radius server when the port is successfully autheticated. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13 | Nodefdb | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.1 | NodefdbGeneralCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.1.1 | ScalarfdbCurCfgAgingTime | read-only | current | Fdb current aging time |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.1.2 | ScalarfdbNewCfgAgingTime | read-write | current | Fdb new aging time. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.2 | TablefdbCurCfgStaticTable | not-accessible | current | The table of FDB static entries. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.2.1 | RowfdbCurCfgStaticEntry | not-accessible | current | A row in the fdb table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.2.1.1 | ColumnfdbCurCfgEntryIndex | read-only | current | The fdb entry index |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.2.1.2 | ColumnfdbCurCfgVlan | read-only | current | Add vlan for fdb entry index |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.2.1.3 | ColumnfdbCurCfgPortIndex | read-only | current | The MAC address port number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.2.1.4 | ColumnfdbCurCfgMac | read-only | current | Add a fdb entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.2.1.5 | ColumnfdbCurCfgTrunk | read-only | current | The MAC address trunk number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.2.1.6 | ColumnfdbCurCfgAdminkey | read-only | current | The MAC address LACP trunk adminkey. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.3 | TablefdbNewCfgStaticTable | not-accessible | current | The table of FDB static entries. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.3.1 | RowfdbNewCfgStaticEntry | not-accessible | current | A row in the fdb table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.3.1.1 | ColumnfdbNewCfgEntryIndex | read-only | current | The fdb entry index |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.3.1.2 | ColumnfdbNewCfgAddVlan | read-create | current | Add vlan for fdb entry index |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.3.1.3 | ColumnfdbNewCfgAddPortIndex | read-create | current | The MAC address port number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.3.1.4 | ColumnfdbNewCfgAddMac | read-create | current | Add a fdb entry, ex:0x00 0x01 0x02 0x03 0x04 0x05 |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.3.1.5 | ColumnfdbNewCfgDelStaticEntry | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.3.1.6 | ColumnfdbNewCfgAddTrunk | read-create | current | The MAC address trunk number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.3.1.7 | ColumnfdbNewCfgAddAdminkey | read-create | current | The MAC address LACP trunk adminkey. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.8 | TablemcastFdbCurCfgTable | not-accessible | current | The table of multicast FDB static entries. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.8.1 | RowmcastFdbCurCfgEntry | not-accessible | current | A row in the multicast fdb table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.8.1.1 | ColumnmcastFdbCurCfgEntryIndex | read-only | current | The multicast fdb entry index |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.8.1.2 | ColumnmcastFdbCurCfgVlan | read-only | current | Add vlan for multicast fdb entry index |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.8.1.3 | ColumnmcastFdbCurCfgPorts | read-only | current | The multicast MAC address port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port … |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.8.1.4 | ColumnmcastFdbCurCfgMac | read-only | current | Add a multicast fdb entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.9 | TablemcastFdbNewCfgTable | not-accessible | current | The table of multicast FDB static entries. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.9.1 | RowmcastFdbNewCfgEntry | not-accessible | current | A row in the multicast fdb table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.9.1.1 | ColumnmcastFdbNewCfgEntryIndex | read-only | current | The multicast fdb entry index |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.9.1.2 | ColumnmcastFdbNewCfgAddVlan | read-create | current | Add vlan for multicast fdb entry index |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.9.1.3 | ColumnmcastFdbNewCfgPorts | read-only | current | The multicast MAC address port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port … |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.9.1.4 | ColumnmcastFdbNewCfgAddPortIndex | read-create | current | The multicast MAC address port number to be added. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.9.1.5 | ColumnmcastFdbNewCfgRemPortIndex | read-create | current | The multicast MAC address port number to be removed. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.9.1.6 | ColumnmcastFdbNewCfgAddMac | read-create | current | Add a multicast fdb entry, ex:0x00 0x01 0x02 0x03 0x04 0x05 |
| 1.3.6.1.4.1.26543.2.7.7.2.1.13.9.1.7 | ColumnmcastFdbNewCfgDelStaticEntry | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14 | NodehotlinksCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.1 | ScalarhotlinksCurCfgOnState | read-only | current | Hot Links ON/OFF setting. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.2 | ScalarhotlinksNewCfgOnState | read-write | current | Hot Links ON/OFF settings. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.3 | ScalarhotlinksCurCfgFdbUpdateState | read-only | current | Enable/disable Hot Links FDB Update setting. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.4 | ScalarhotlinksNewCfgFdbUpdateState | read-write | current | Enable/disable Hot Links FDB Update setting. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.5 | ScalarhotlinksMaxTriggerEntries | read-only | current | The maximum number of entries in the Hot Links Trigger Table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.6 | TablehotlinksCurCfgTriggerTable | not-accessible | current | The Hot Links Trigger Table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.6.1 | RowhotlinksCurCfgTriggerTableEntry | not-accessible | current | A row in the Hot Links Trigger Table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.6.1.1 | ColumnhotlinksCurCfgTriggerId | read-only | current | The Trigger identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.6.1.2 | ColumnhotlinksCurCfgTriggerName | read-only | current | A textual string containing the trigger name. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.6.1.3 | ColumnhotlinksCurCfgTriggerState | read-only | current | Enable/disable Trigger state. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.6.1.4 | ColumnhotlinksCurCfgTriggerPreemptState | read-only | current | Enable/disable Preemption state. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.6.1.5 | ColumnhotlinksCurCfgTriggerFdelay | read-only | current | Forward Delay setting (in secs). |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.6.1.6 | ColumnhotlinksCurCfgTriggerMasterPortIndex | read-only | current | The master interface port number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.6.1.7 | ColumnhotlinksCurCfgTriggerMasterTrunk | read-only | current | The master interface trunk number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.6.1.8 | ColumnhotlinksCurCfgTriggerBackupPortIndex | read-only | current | The backup interface port number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.6.1.9 | ColumnhotlinksCurCfgTriggerBackupTrunk | read-only | current | The backup interface trunk number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.6.1.10 | ColumnhotlinksCurCfgTriggerDelete | read-only | current | Delete a Hot Links trigger configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.6.1.11 | ColumnhotlinksCurCfgTriggerMasterAdminkey | read-only | current | The master interface admin key number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.6.1.12 | ColumnhotlinksCurCfgTriggerBackupAdminkey | read-only | current | The backup interface admin key number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.7 | TablehotlinksNewCfgTriggerTable | not-accessible | current | The Hot Links Trigger Table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.7.1 | RowhotlinksNewCfgTriggerTableEntry | not-accessible | current | A row in the Hot Links Trigger Table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.7.1.1 | ColumnhotlinksNewCfgTriggerId | read-only | current | The Trigger identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.7.1.2 | ColumnhotlinksNewCfgTriggerName | read-write | current | A textual string containing the trigger name. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.7.1.3 | ColumnhotlinksNewCfgTriggerState | read-write | current | Enable/disable Trigger state. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.7.1.4 | ColumnhotlinksNewCfgTriggerPreemptState | read-write | current | Enable/disable Preemption state. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.7.1.5 | ColumnhotlinksNewCfgTriggerFdelay | read-write | current | Forward Delay setting (in secs). |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.7.1.6 | ColumnhotlinksNewCfgTriggerMasterPortIndex | read-write | current | The master interface port number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.7.1.7 | ColumnhotlinksNewCfgTriggerMasterTrunk | read-write | current | The master interface trunk number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.7.1.8 | ColumnhotlinksNewCfgTriggerBackupPortIndex | read-write | current | The backup interface port number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.7.1.9 | ColumnhotlinksNewCfgTriggerBackupTrunk | read-write | current | The backup interface trunk number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.7.1.10 | ColumnhotlinksNewCfgTriggerDelete | read-write | current | Delete a Hot Links trigger configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.7.1.11 | ColumnhotlinksNewCfgTriggerMasterAdminkey | read-write | current | The master interface admin key number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.7.1.12 | ColumnhotlinksNewCfgTriggerBackupAdminkey | read-write | current | The backup interface admin key number. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.8 | ScalarhotlinksCurCfgBpduState | read-only | current | Enable/disable Hot Links BPDU flood setting. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.9 | ScalarhotlinksNewCfgBpduState | read-write | current | Enable/disable Hot Links BPDU flood setting. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.10 | ScalarhotlinksCurCfgFdbUpdateRate | read-only | current | Hot Links FDB update rate (packets per second). |
| 1.3.6.1.4.1.26543.2.7.7.2.1.14.11 | ScalarhotlinksNewCfgFdbUpdateRate | read-write | current | Hot Links FDB update rate (packets per second). |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15 | NodelldpCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.1 | ScalarlldpPortTableMaxEnt | read-only | current | The maximum number of rows in the port configuration host table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.2 | TablelldpCurCfgPortTable | not-accessible | current | The table of LLDP port configuration in the current_configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.2.1 | RowlldpCurCfgPortEntry | not-accessible | current | A row in the LLDP port configuration table in the current_configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.2.1.1 | ColumnlldpCurCfgPortIndx | read-only | current | The index of the row in LLDP port configurations table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.2.1.2 | ColumnlldpCurCfgPortAdmStat | read-only | current | This is the admin status of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.2.1.3 | ColumnlldpCurCfgPortSnmpTrap | read-only | current | This is the SNMP trap notification state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.2.1.4 | ColumnlldpCurCfgPortportdesctlv | read-only | current | This is the Port Description TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.2.1.5 | ColumnlldpCurCfgPortsysnametlv | read-only | current | This is the System Name TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.2.1.6 | ColumnlldpCurCfgPortsysdescrtlv | read-only | current | This is the System Description TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.2.1.7 | ColumnlldpCurCfgPortsyscaptlv | read-only | current | This is the System Capabilities TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.2.1.8 | ColumnlldpCurCfgPortmgmtaddrtlv | read-only | current | This is the Management Address TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.2.1.9 | ColumnlldpCurCfgPortportvidtlv | read-only | current | This is the Port VLAN ID TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.2.1.10 | ColumnlldpCurCfgPortportprottlv | read-only | current | This is the Port and Protocol VLAN ID TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.2.1.11 | ColumnlldpCurCfgPortvlannametlv | read-only | current | This is the VLAN Name TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.2.1.12 | ColumnlldpCurCfgPortprotidtlv | read-only | current | This is the Protocol Identity TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.2.1.13 | ColumnlldpCurCfgPortmacphytlv | read-only | current | This is the MAC/PHY Configuration/Status TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.2.1.14 | ColumnlldpCurCfgPortpowermditlv | read-only | current | This is the Power Via MDI TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.2.1.15 | ColumnlldpCurCfgPortlinkaggrtlv | read-only | current | This is the Link Aggregation TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.2.1.16 | ColumnlldpCurCfgPortframesztlv | read-only | current | This is the Maximum Frame Size TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.2.1.18 | ColumnlldpCurCfgPortevbtlv | read-only | current | This is the EVB TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.3 | TablelldpNewCfgPortTable | not-accessible | current | The table of LLDP port configuration in the new_configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.3.1 | RowlldpNewCfgPortEntry | not-accessible | current | A row in the LLDP port configuration table in the new_configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.3.1.1 | ColumnlldpNewCfgPortIndx | read-only | current | The index of the row in LLDP port configurations table. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.3.1.2 | ColumnlldpNewCfgPortAdmStat | read-write | current | This is the admin status of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.3.1.3 | ColumnlldpNewCfgPortSnmpTrap | read-write | current | This is the SNMP trap notification state of the LLDP port |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.3.1.4 | ColumnlldpNewCfgPortportdesctlv | read-write | current | This is the Port Description TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.3.1.5 | ColumnlldpNewCfgPortsysnametlv | read-write | current | This is the System Name TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.3.1.6 | ColumnlldpNewCfgPortsysdescrtlv | read-write | current | This is the System Description TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.3.1.7 | ColumnlldpNewCfgPortsyscaptlv | read-write | current | This is the System Capabilities TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.3.1.8 | ColumnlldpNewCfgPortmgmtaddrtlv | read-write | current | This is the Management Address TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.3.1.9 | ColumnlldpNewCfgPortportvidtlv | read-write | current | This is the Port VLAN ID TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.3.1.10 | ColumnlldpNewCfgPortportprottlv | read-write | current | This is the Port and Protocol VLAN ID TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.3.1.11 | ColumnlldpNewCfgPortvlannametlv | read-write | current | This is the VLAN Name TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.3.1.12 | ColumnlldpNewCfgPortprotidtlv | read-write | current | This is the Protocol Identity TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.3.1.13 | ColumnlldpNewCfgPortmacphytlv | read-write | current | This is the MAC/PHY Configuration/Status TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.3.1.14 | ColumnlldpNewCfgPortpowermditlv | read-write | current | This is the Power Via MDI TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.3.1.15 | ColumnlldpNewCfgPortlinkaggrtlv | read-write | current | This is the Link Aggregation TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.3.1.16 | ColumnlldpNewCfgPortframesztlv | read-write | current | This is the Maximum Frame Size TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.3.1.17 | ColumnlldpNewCfgPortalltlv | read-write | current | Set the corresponding state for all the LLDP port's TLVs. other(3) is returned when the object is read. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.4 | NodelldpGeneral | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.4.1 | ScalarlldpCurCfgState | read-only | current | LLDP global state. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.4.2 | ScalarlldpNewCfgState | read-write | current | Globally turn LLDP on or off. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.4.3 | ScalarlldpCurCfgMsgTxInt | read-only | current | LLDP message transmission interval for LLDPDU. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.4.4 | ScalarlldpNewCfgMsgTxInt | read-write | current | LLDP message transmission interval for LLDPDU. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.4.5 | ScalarlldpCurCfgMsgTxHld | read-only | current | LLDP message transmission holdtime-multiplier. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.4.6 | ScalarlldpNewCfgMsgTxHld | read-write | current | LLDP message transmission holdtime-multiplier. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.4.7 | ScalarlldpCurCfgNotifInt | read-only | current | LLDP minimum SNMP trap notification interval. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.4.8 | ScalarlldpNewCfgNotifInt | read-write | current | LLDP minimum SNMP trap notification interval. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.4.9 | ScalarlldpCurCfgTxDelay | read-only | current | LLDP delay interval between advertisements. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.4.10 | ScalarlldpNewCfgTxDelay | read-write | current | LLDP delay interval between advertisements. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.4.11 | ScalarlldpCurCfgReinitDelay | read-only | current | LLDP reinit delay interval. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.15.4.12 | ScalarlldpNewCfgReinitDelay | read-write | current | LLDP reinit delay interval. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18 | NodevlagCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.1 | NodevlagIslCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.1.1 | ScalarvlagCurIslCfgPortChannel | read-only | current | Current vLAG ISL portchannel |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.1.2 | ScalarvlagNewIslCfgPortChannel | read-write | current | This object is used to change the vLAG ISL portchannel. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.1.3 | ScalarvlagCurIslCfgAdminKey | read-only | current | Current vLAG ISL admin key. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.1.4 | ScalarvlagNewIslCfgAdminKey | read-write | current | This object is used to change the vLAG ISL admin key. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.4 | ScalarvlagCurCfgSwitchPriority | read-only | current | Current vLAG switch priority |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.5 | ScalarvlagNewCfgSwitchPriority | read-write | current | This object is used to change the vLAG priority of this switch. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.6 | TablevlagCurCfgTrunkTable | not-accessible | current | A table of objects of the vLAG groups configured in this switch. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.6.1 | RowvlagCurCfgTrunkTableEntry | not-accessible | current | The configuration objects for an vLAG group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.6.1.1 | ColumnvlagCurCfgTrunkIndex | read-only | current | The identifier of the trunk group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.6.1.2 | ColumnvlagCurCfgTrunkState | read-only | current | The current administrative state of the vLAG group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.7 | TablevlagNewCfgTrunkTable | not-accessible | current | A table of objects of the vLAG groups configured in this switch. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.7.1 | RowvlagNewCfgTrunkTableEntry | not-accessible | current | The configuration objects for an vLAG group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.7.1.1 | ColumnvlagNewCfgTrunkIndex | read-write | current | The identifier of the trunk group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.7.1.2 | ColumnvlagNewCfgTrunkState | read-write | current | The new administrative state of the vLAG group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.8 | TablevlagCurCfgLacpTable | not-accessible | current | A table of objects of the vLAG groups configured in this switch. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.8.1 | RowvlagCurCfgLacpTableEntry | not-accessible | current | The configuration objects for an vLAG group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.8.1.1 | ColumnvlagCurCfgLacpKey | read-only | current | The identifier of the trunk group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.8.1.2 | ColumnvlagCurCfgLacpState | read-only | current | The current administrative state of the vLAG group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.9 | TablevlagNewCfgLacpTable | not-accessible | current | A table of objects of the vLAG groups configured in this switch. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.9.1 | RowvlagNewCfgLacpTableEntry | not-accessible | current | The configuration objects for an vLAG group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.9.1.1 | ColumnvlagNewCfgLacpKey | read-only | current | The identifier of the trunk group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.9.1.2 | ColumnvlagNewCfgLacpState | read-write | current | The new administrative state of the vLAG group. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.10 | ScalarvlagCurCfgHlthchkPeerIp | read-only | current | The current Health check Peer ip4 address. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.11 | ScalarvlagNewCfgHlthchkPeerIp | read-write | current | The New Health check Peer ip4 address. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.12 | ScalarvlagCurCfgTierId | read-only | current | Current vLAG Tier ID |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.13 | ScalarvlagNewCfgTierId | read-write | current | This object is used to change the vLAG Tier ID of this switch. vLAG consist of 2 vLAG peer switches connected by ISL link, the system formed by the switches is… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.14 | ScalarvlagCurCfgStartupDelayInterval | read-only | current | Current vLAG Startup delay interval |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.15 | ScalarvlagNewCfgStartupDelayInterval | read-write | current | This object is used to change the vLAG startup Delay Timer interval. The Timer is used to prevent traffic lost for the vLAG ports may be up before the ISL is u… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.16 | ScalarvlagCurCfgGlobalEnable | read-only | current | Current vLAG global status on switch. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.17 | ScalarvlagNewCfgGlobalEnable | read-write | current | Set true to enable vLAG globally or Set false to disable vLAG globally on switch. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.18 | ScalarvlagCurCfgHlthchkConnectRetryInterval | read-only | current | In case of healtcheck TCP connection can not be established, interval at which the retry attempt will be made to connect to the peer. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.19 | ScalarvlagNewCfgHlthchkConnectRetryInterval | read-write | current | In case of healtcheck TCP connection can not be established, interval at which the retry attempt will be made to connect to the peer. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.20 | ScalarvlagCurCfgHlthchkKeepaliveAttempts | read-only | current | Number of keepalive attempts made before declaring peer is down. Within this time, atleast one of the keepalive message should have been received from the peer. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.21 | ScalarvlagNewCfgHlthchkKeepaliveAttempts | read-write | current | Number of keepalive attempts made before declaring peer is down.Within this time, atleast one of the keepalive message should have been received from the peer. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.22 | ScalarvlagCurCfgHlthchkKeepaliveInterval | read-only | current | Interval between keepalives sent over healthcheck TCP session to keep the session alive. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.23 | ScalarvlagNewCfgHlthchkKeepaliveInterval | read-write | current | Interval between keepalives sent over healthcheck TCP session to keep the session alive. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.24 | ScalarvlagCurCfgAutoRecoveryInterval | read-only | current | Current vLAG Auto Recovery interval |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.25 | ScalarvlagNewCfgAutoRecoveryInterval | read-write | current | This object is used to change the vLAG Auto Recovery Timer interval. The Timer is used to prevent all vlag ports stay in ErrDisabled state when booting two vLA… |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.26 | ScalarvlagCurCfgHlthchkPeerIpv6 | read-only | current | The current Health check Peer ipv6 address. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.18.27 | ScalarvlagNewCfgHlthchkPeerIpv6 | read-write | current | The New Health check Peer ipv6 address. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.19 | NodeecpCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.19.1 | ScalarecpCurCfgRetrans | read-only | current | The ECP retransmission interval in millisecond |
| 1.3.6.1.4.1.26543.2.7.7.2.1.19.2 | ScalarecpNewCfgRetrans | read-write | current | The ECP retransmission interval in millisecond |
| 1.3.6.1.4.1.26543.2.7.7.2.1.20 | NodeslpCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.2.1.20.1 | ScalarslpCurCfgGlobalEnable | read-only | current | Current SLP global status on switch. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.20.2 | ScalarslpNewCfgGlobalEnable | read-write | current | Set to enabled to enable SLP globally or Set to disabled to disable SLP globally on switch. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.20.3 | ScalarslpCurCfgActiveDaDisEnable | read-only | current | Current SLP active directory agent discovery status on switch. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.20.4 | ScalarslpNewCfgActiveDaDisEnable | read-write | current | Set to enabled to enable SLP active directory agent discovery or Set to disabled to disable SLP active directory agent discovery on switch. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.20.5 | ScalarslpCurCfgActiveDaDisStartWaitTime | read-only | current | Current SLP active directory agent discovery start wait time measured in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.2.1.20.6 | ScalarslpNewCfgActiveDaDisStartWaitTime | read-write | current | This object is used to change the SLP active directory agent discovery start wait time measured in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.2.2 | Nodelayer2Stats | |||
| 1.3.6.1.4.1.26543.2.7.7.2.2.1 | NodefdbStats | |||
| 1.3.6.1.4.1.26543.2.7.7.2.2.1.3 | ScalarfdbStatsCurrent | read-only | current | Current number of entries in the Forwarding Database. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.1.4 | ScalarfdbStatsHiwat | read-only | current | Highest number of entries recorded at any given time in the Forwarding Database. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.1.11 | ScalarfdbStatsClear | read-write | current | Clear FDB statistics |
| 1.3.6.1.4.1.26543.2.7.7.2.2.2 | NodestpStats | |||
| 1.3.6.1.4.1.26543.2.7.7.2.2.2.1 | TablestgStatsPortTable | not-accessible | current | The table of Spanning Tree Group port statistics. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.2.1.1 | RowstgStatsPortTableEntry | not-accessible | current | Statistics about port of a particular Spanning Tree Group. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.2.1.1.1 | ColumnstgStatsStpIndex | read-only | current | The identifier of a particular Spanning Tree Group. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.2.1.1.2 | ColumnstgStatsPortIndex | read-only | current | The port identifier of a particular Spanning Tree Group. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.2.1.1.3 | ColumnstgStatsPortRcvCfgBpdus | read-only | current | Number of Configuration BPDU's received on this port. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.2.1.1.4 | ColumnstgStatsPortRcvTcnBpdus | read-only | current | Number of TCN BPDU's received on this port. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.2.1.1.5 | ColumnstgStatsPortXmtCfgBpdus | read-only | current | Number of Configuration BPDU's trasmitted from the port. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.2.1.1.6 | ColumnstgStatsPortXmtTcnBpdus | read-only | current | Number of TCN BPDU's trasmitted from the port. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.4 | NodelacpStats | |||
| 1.3.6.1.4.1.26543.2.7.7.2.2.4.1 | TablelacpStatsTable | not-accessible | current | The table of LACP Stats. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.4.1.1 | RowlacpStatsTableEntry | not-accessible | current | Lacp status info. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.4.1.1.1 | ColumnlacpStatsIndex | read-only | current | Index |
| 1.3.6.1.4.1.26543.2.7.7.2.2.4.1.1.2 | ColumnlacpdusRx | read-only | current | Valid LACPDUs received |
| 1.3.6.1.4.1.26543.2.7.7.2.2.4.1.1.3 | ColumnmarkerpdusRx | read-only | current | Valid Marker PDUs received |
| 1.3.6.1.4.1.26543.2.7.7.2.2.4.1.1.4 | ColumnmarkerresponsepdusRx | read-only | current | Valid Marker Rsp PDUs received |
| 1.3.6.1.4.1.26543.2.7.7.2.2.4.1.1.5 | ColumnunknownRx | read-only | current | Unknown version/TLV type |
| 1.3.6.1.4.1.26543.2.7.7.2.2.4.1.1.6 | ColumnillegalRx | read-only | current | Illegal subtype received |
| 1.3.6.1.4.1.26543.2.7.7.2.2.4.1.1.7 | ColumnlacpdusTx | read-only | current | LACPDUs transmitted |
| 1.3.6.1.4.1.26543.2.7.7.2.2.4.1.1.8 | ColumnmarkerpdusTx | read-only | current | Market PDUs transmitted |
| 1.3.6.1.4.1.26543.2.7.7.2.2.4.1.1.9 | ColumnmarkerresponsepdusTx | read-only | current | Marker Rsp PDUs transmitted |
| 1.3.6.1.4.1.26543.2.7.7.2.2.4.1.1.10 | ColumnlacpClearStats | read-write | current | Setting this to clear(2) results in clearing the LACP statistics. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.6 | NodehotlinksStats | |||
| 1.3.6.1.4.1.26543.2.7.7.2.2.6.1 | TablehotlinksStatsTriggerTable | not-accessible | current | The Hot Links Trigger Table Stats. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.6.1.1 | RowhotlinksStatsTriggerTableEntry | not-accessible | current | A row in the Hot Links Trigger Table Stats. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.6.1.1.1 | ColumnhotlinksStatsTriggerId | read-only | current | The Trigger identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.6.1.1.2 | ColumnhotlinksStatsTriggerName | read-only | current | A textual string containing the trigger name. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.6.1.1.3 | ColumnhotlinksStatsTriggerMasterActive | read-only | current | The number of times the master interface was set to active. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.6.1.1.4 | ColumnhotlinksStatsTriggerBackupActive | read-only | current | The number of times the backup interface was set to active. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.6.1.1.5 | ColumnhotlinksStatsTriggerFdbUpdate | read-only | current | The number of times an FDB update was performed. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.6.1.1.6 | ColumnhotlinksStatsTriggerFdbFailed | read-only | current | The number of times an FDB update failed. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.7 | NodelldpStats | |||
| 1.3.6.1.4.1.26543.2.7.7.2.2.7.1 | ScalarlldpStatsTableMaxEnt | read-only | current | The maximum number of rows in the statistics host table. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.7.2 | TablelldpStatsTable | not-accessible | current | The table of LLDP statistics. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.7.2.1 | RowlldpStatsTableEntry | not-accessible | current | LLDP statistics info. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.7.2.1.1 | ColumnlldpStatsIndex | read-only | current | The index of the row in LLDP port statistics. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.7.2.1.2 | ColumnlldpStatsFramesOutTotal | read-only | current | The total number of LLDP frames transmitted in this port. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.7.2.1.3 | ColumnlldpStatsFramesInTotal | read-only | current | The total number of LLDP frames received in this port. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.7.2.1.4 | ColumnlldpStatsFramesInErrorsTotal | read-only | current | The total number of erroneous LLDP frames received in this port. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.7.2.1.5 | ColumnlldpStatsFramesDiscardedTotal | read-only | current | The total number of received LLDP frames discarded in this port. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.7.2.1.6 | ColumnlldpStatsTLVsUnrecognizedTotal | read-only | current | The total number of unrecognized TLVs in this port. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.7.2.1.7 | ColumnlldpStatsAgeoutsTotal | read-only | current | The total number of neighbor's information deleted in this port. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.7.2.1.8 | ColumnlldpStatsClear | read-write | current | Setting this to clear(2) results in clearing the LLDP statistics. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.7.3 | ScalarlldpStatsClearAll | read-write | current | Setting this to clear(2) results in clearing the LLDP statistics for all the ports. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.8 | NodeoamStats | |||
| 1.3.6.1.4.1.26543.2.7.7.2.2.8.1 | TableoamStatsPortTable | not-accessible | current | The table of OAM port statistics. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.8.1.1 | RowoamStatsPortEntry | not-accessible | current | Statistics about OAM Port |
| 1.3.6.1.4.1.26543.2.7.7.2.2.8.1.1.1 | ColumnoamStatsPortIndex | read-only | current | The OAM Port number for which the table is related. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.8.1.1.2 | ColumnoamStatsPortInfoTx | read-only | current | The number of transmitted OAM information packets |
| 1.3.6.1.4.1.26543.2.7.7.2.2.8.1.1.3 | ColumnoamStatsPortInfoRx | read-only | current | The number of received OAM information packets |
| 1.3.6.1.4.1.26543.2.7.7.2.2.8.1.1.4 | ColumnoamStatsPortUnsupTx | read-only | current | The number of transmitted OAM unsupported packets |
| 1.3.6.1.4.1.26543.2.7.7.2.2.8.1.1.5 | ColumnoamStatsPortUnsupRx | read-only | current | The number of received OAM unsupported packets |
| 1.3.6.1.4.1.26543.2.7.7.2.2.8.1.1.6 | ColumnoamStatsPortLocalLinkFaults | read-only | current | The number of local OAM link fault packets |
| 1.3.6.1.4.1.26543.2.7.7.2.2.8.1.1.7 | ColumnoamStatsPortLocalCriticalEvents | read-only | current | The number of local OAM critical event packets |
| 1.3.6.1.4.1.26543.2.7.7.2.2.8.1.1.8 | ColumnoamStatsPortLocalDyingGasps | read-only | current | The number of local OAM dying gasp packets |
| 1.3.6.1.4.1.26543.2.7.7.2.2.8.1.1.9 | ColumnoamStatsPortRemoteLinkFaults | read-only | current | The number of remote OAM link fault packets |
| 1.3.6.1.4.1.26543.2.7.7.2.2.8.1.1.10 | ColumnoamStatsPortRemoteCriticalEvents | read-only | current | The number of remote OAM critical event packets |
| 1.3.6.1.4.1.26543.2.7.7.2.2.8.1.1.11 | ColumnoamStatsPortRemoteDyingGasps | read-only | current | The number of remote OAM dying gasp packets |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11 | NodevlagStats | |||
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.1 | NodevlagStatsSystem | |||
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.1.1 | ScalarvlagStatsClear | read-write | current | Setting this object to 'clear' will reset all statistics objects of VLAG. A get action of this object will always return 'other'. Setting this object to 'other… |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.2 | NodevlagStatsIsl | |||
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.2.1 | ScalarvlagStatsIslInOctets | read-only | current | The total number of vlag ISL octets received. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.2.2 | ScalarvlagStatsIslInPackets | read-only | current | The total number of vlag ISL packets received. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.2.3 | ScalarvlagStatsIslOutOctets | read-only | current | The total number of vlag ISL octets sent. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.2.4 | ScalarvlagStatsIslOutPackets | read-only | current | The total number of vlag ISL packets sent. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.3 | NodevlagStatsHealth | |||
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.4 | NodevlagStatsLacp | |||
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5 | NodevlagStatsPdu | |||
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.1 | ScalarvlagStatsPduSentRoleElection | read-only | current | The total number of vlag PDUs sent for role elections |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.2 | ScalarvlagStatsPduSentSystemInfo | read-only | current | The total number of vlag PDUs sent for system info |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.7 | ScalarvlagStatsPduSentFdbDynamicAdd | read-only | current | The total number of vlag PDUs sent for addition of FDB dynamic entry |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.8 | ScalarvlagStatsPduSentFdbDynamicDel | read-only | current | The total number of vlag PDUs sent for deletion of FDB dynamic entry |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.9 | ScalarvlagStatsPduSentFdbInactiveAdd | read-only | current | The total number of vlag PDUs sent for addition of FDB inactive entry |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.10 | ScalarvlagStatsPduSentFdbInactiveDel | read-only | current | The total number of vlag PDUs sent for deletion of FDB inactive entry |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.13 | ScalarvlagStatsPduSentHlthCheck | read-only | current | The total number of vlag PDUs sent for Health check |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.15 | ScalarvlagStatsPduSentOther | read-only | current | The total number of vlag PDUs sent for others |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.16 | ScalarvlagStatsPduSentUnknown | read-only | current | The total number of vlag PDUs sent for unknowns |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.17 | ScalarvlagStatsPduRcvRoleElection | read-only | current | The total number of vlag PDUs received for role elections |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.18 | ScalarvlagStatsPduRcvSystemInfo | read-only | current | The total number of vlag PDUs received for system info |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.23 | ScalarvlagStatsPduRcvFdbDynamicAdd | read-only | current | The total number of vlag PDUs received for addition of FDB dynamic entry |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.24 | ScalarvlagStatsPduRcvFdbDynamicDel | read-only | current | The total number of vlag PDUs received for deletion of FDB dynamic entry |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.25 | ScalarvlagStatsPduRcvFdbInactiveAdd | read-only | current | The total number of vlag PDUs received for addition of FDB inactive entry |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.26 | ScalarvlagStatsPduRcvFdbInactiveDel | read-only | current | The total number of vlag PDUs received for deletion of FDB inactive entry |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.29 | ScalarvlagStatsPduRcvHlthCheck | read-only | current | The total number of vlag PDUs received for Health check |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.31 | ScalarvlagStatsPduRcvOther | read-only | current | The total number of vlag PDUs received for others |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.32 | ScalarvlagStatsPduRcvUnknown | read-only | current | The total number of vlag PDUs received for unknowns |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.33 | ScalarvlagStatsPduSentPeerInstanceEnable | read-only | current | The total number of vlag PDUs sent for peer instance enable |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.34 | ScalarvlagStatsPduSentPeerInstanceDisable | read-only | current | The total number of vlag PDUs sent for peer instance disable |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.35 | ScalarvlagStatsPduSentISLHello | read-only | current | The total number of vlag PDUs sent for ISL hello |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.36 | ScalarvlagStatsPduRcvISLHello | read-only | current | The total number of vlag PDUs received for ISL hello |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.37 | ScalarvlagStatsPduRcvPeerInstanceEnable | read-only | current | The total number of vlag PDUs received for peer instance enable |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.5.38 | ScalarvlagStatsPduRcvPeerInstanceDisable | read-only | current | The total number of vlag PDUs received for peer instance disable |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.6 | NodevlagStatsIgmp | |||
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.6.1 | ScalarvlagStatsIgmpReportsForwarded | read-only | current | The total number of IGMP reports forwarded to the peer |
| 1.3.6.1.4.1.26543.2.7.7.2.2.11.6.2 | ScalarvlagStatsIgmpLeavesForwarded | read-only | current | The total number of IGMP leaves forwarded to the peer |
| 1.3.6.1.4.1.26543.2.7.7.2.2.12 | NodeslpStats | |||
| 1.3.6.1.4.1.26543.2.7.7.2.2.12.1 | TableslpStatsTxCountersTable | not-accessible | current | A table with all the SLP Send counters. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.12.1.1 | RowslpStatsTxCounterEntry | not-accessible | current | The configuration objects for a SLP Send counter entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.12.1.1.1 | ColumnslpTxCounterIndex | read-only | current | The index of this counter. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.12.1.1.2 | ColumnslpTxCounterName | read-only | current | The name of this counter. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.12.1.1.3 | ColumnslpTxCounterUnicast | read-only | current | The unicast value of this counter. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.12.1.1.4 | ColumnslpTxCounterMulticast | read-only | current | The multicast value of this counter. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.12.2 | TableslpStatsRxCountersTable | not-accessible | current | A table with all the SLP Receive counters. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.12.2.1 | RowslpStatsRxCounterEntry | not-accessible | current | The configuration objects for a SLP Receive counter entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.12.2.1.1 | ColumnslpRxCounterIndex | read-only | current | The index this counter. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.12.2.1.2 | ColumnslpRxCounterName | read-only | current | The name of this counter. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.12.2.1.3 | ColumnslpRxCounterUnicast | read-only | current | The unicast value of this counter. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.12.2.1.4 | ColumnslpRxCounterMulticast | read-only | current | The multicast value of this counter. |
| 1.3.6.1.4.1.26543.2.7.7.2.2.12.3 | ScalarslpCountersClear | read-write | current | Setting this object to 'clear' will reset all SLP counters. A get action of this object will always return 'other'. Setting this object to 'other' is not allow… |
| 1.3.6.1.4.1.26543.2.7.7.2.3 | Nodelayer2Info | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.1 | NodefdbInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.1.1 | ScalarfdbClear | read-write | current | Setting this value to clear(2) clears the entire master FDB. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.1.2 | TablefdbTable | not-accessible | current | The table of FDB entries. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.1.2.1 | RowfdbEntry | not-accessible | current | A row in the FDB table |
| 1.3.6.1.4.1.26543.2.7.7.2.3.1.2.1.1 | ColumnfdbMacAddr | read-only | current | The MAC address for the FDB entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.1.2.1.2 | ColumnfdbVlan | read-only | current | The VLAN ID for the FDB entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.1.2.1.3 | ColumnfdbSrcPortIndex | read-only | current | Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance has been seen. A… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.1.2.1.4 | ColumnfdbState | read-only | current | The state of the FDB entry. The meanings of the values are : unknown(1) : the MAC address has not yet been learned by the switch but has only been seen as a de… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.1.2.1.7 | ColumnfdbSrcTrunk | read-only | current | Either the value '0', or the trunk number of the trunk on which a frame having a source address equal to the value of the corresponding instance has been seen.… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.1.2.1.8 | ColumnfdbStatus | read-only | current | '1' if it is permanent '0' if it is not permanent |
| 1.3.6.1.4.1.26543.2.7.7.2.3.1.3 | TablemcastFdbTable | not-accessible | current | The table of static multicast FDB entries. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.1.3.1 | RowmcastFdbEntry | not-accessible | current | A row in the static multicast FDB table |
| 1.3.6.1.4.1.26543.2.7.7.2.3.1.3.1.1 | ColumnmcastFdbEntryIndex | read-only | current | The static multicast fdb entry index |
| 1.3.6.1.4.1.26543.2.7.7.2.3.1.3.1.2 | ColumnmcastFdbMacAddr | read-only | current | The static multicast MAC address for the FDB entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.1.3.1.3 | ColumnmcastFdbVlan | read-only | current | The VLAN ID for the FDB entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.1.3.1.4 | ColumnmcastFdbSrcPorts | read-only | current | The multicast MAC address port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port … |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2 | NodestpInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.1 | TablestpInfoTable | not-accessible | current | The table of Spanning Tree Group information. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.1.1 | RowstpInfoTableEntry | not-accessible | current | Information about a particular Spanning Tree Group. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.1.1.1 | ColumnstpInfoIndex | read-only | current | The identifier of a particular Spanning Tree Group. This is also index to the entLogicalTable of Entity MIB. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.1.1.2 | ColumnstpInfoTimeSinceTopChange | read-only | current | The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.1.1.3 | ColumnstpInfoTopChanges | read-only | current | The total number of topology changes detected by this bridge since the management entity was last reset or initialized. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.1.1.4 | ColumnstpInfoDesignatedRoot | read-only | current | The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Ide… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.1.1.5 | ColumnstpInfoRootCost | read-only | current | The cost of the path to the root as seen from this bridge. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.1.1.6 | ColumnstpInfoRootPortIndex | read-only | current | The port number of the port which offers the lowest cost path from this bridge to the root bridge. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.1.1.7 | ColumnstpInfoMaxAge | read-only | current | The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is … |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.1.1.8 | ColumnstpInfoHelloTime | read-only | current | The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become … |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.1.1.9 | ColumnstpInfoForwardDelay | read-only | current | This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.1.1.10 | ColumnstpInfoHoldTime | read-only | current | This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredth… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.2 | TablestpInfoPortTable | not-accessible | current | The table of Spanning Tree Group port information. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.2.1 | RowstpInfoPortTableEntry | not-accessible | current | Information about port configuration for a particular Spanning Tree Group. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.2.1.1 | ColumnstpInfoPortStpIndex | read-only | current | The identifier of a particular Spanning Tree Group. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.2.1.2 | ColumnstpInfoPortIndex | read-only | current | The port identifier of a particular Spanning Tree Group. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.2.1.3 | ColumnstpInfoPortState | read-only | current | The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the … |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.2.1.4 | ColumnstpInfoPortDesignatedRoot | read-only | current | The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the po… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.2.1.5 | ColumnstpInfoPortDesignatedCost | read-only | current | The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.2.1.6 | ColumnstpInfoPortDesignatedBridge | read-only | current | The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.2.1.7 | ColumnstpInfoPortDesignatedPort | read-only | current | The Port Identifier of the port on the Designated Bridge for this port's segment. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.2.1.8 | ColumnstpInfoPortForwardTransitions | read-only | current | The number of times this port has transitioned from the Learning state to the Forwarding state. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.2.1.9 | ColumnstpInfoPortPathCost | read-only | current | The path cost of the port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.2.1.10 | ColumnstpInfoPortRole | read-only | current | The port role. Returns unknown(7) when MSTP/RSTP is not enabled, otherwise returns appropriate port role. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.2.1.11 | ColumnstpInfoPortLinkType | read-only | current | The point-to-point status of the LAN segment attached to this port. A value of p2p (1) indicates that this port is being treated as if it is connected to a poi… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.2.1.12 | ColumnstpInfoPortEdge | read-only | current | The port is an edge port or not. Returns disabled(2) when the port is not an edge port and returns enabled(1) when it is an edge port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.2.1.13 | ColumnstpInfoPortExtGuard | read-only | current | Current STP guard state. Not include BPDU Guard. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.2.2.1.14 | ColumnstpInfoPortPriority | read-only | current | The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting this value. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3 | NodelacpInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.1 | TablelacpInfoAggrTable | not-accessible | current | The table of LACP aggregator information. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.1.1 | RowlacpInfoAggrTableEntry | not-accessible | current | Information about a LACP aggregator. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.1.1.1 | ColumnlacpInfoAggrIndex | read-only | current | The aggregator identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.1.1.2 | ColumnlacpInfoAggrId | read-only | current | LACP aggregator ID |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.1.1.3 | ColumnlacpInfoAggrMac | read-only | current | LACP aggregator MAC address |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.1.1.4 | ColumnlacpInfoAggrActSysPrio | read-only | current | LACP aggregator actor system priority |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.1.1.5 | ColumnlacpInfoAggrActSysId | read-only | current | LACP aggregator actor system ID |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.1.1.6 | ColumnlacpInfoAggrIndivState | read-only | current | LACP aggregator individual state |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.1.1.7 | ColumnlacpInfoAggrActAdminKey | read-only | current | LACP aggregator actor admin key |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.1.1.8 | ColumnlacpInfoAggrActOperKey | read-only | current | LACP aggregator actor oper key |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.1.1.9 | ColumnlacpInfoAggrPartSysPrio | read-only | current | LACP aggregator partner system priority |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.1.1.10 | ColumnlacpInfoAggrPartSysId | read-only | current | LACP aggregator partner system ID |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.1.1.11 | ColumnlacpInfoAggrPartOperKey | read-only | current | LACP aggregator partner oper key |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.1.1.12 | ColumnlacpInfoAggrReadyState | read-only | current | LACP aggregator ready state |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.1.1.13 | ColumnlacpInfoAggrNumPorts | read-only | current | Number of ports in aggregator |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.1.1.15 | ColumnlacpInfoAggrMinLinks | read-only | current | Min Links of ports in aggregator |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2 | NodelacpInfoPort | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1 | TablelacpInfoPortGeneralTable | not-accessible | current | The table of LACP port general information. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1 | RowlacpInfoPortGeneralTableEntry | not-accessible | current | General information about a LACP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.1 | ColumnlacpInfoPortGeneralIndex | read-only | current | The port identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.2 | ColumnlacpInfoPortLacpEna | read-only | current | LACP enabled on port |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.3 | ColumnlacpInfoPortAdminEna | read-only | current | LACP port admin enabled |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.4 | ColumnlacpInfoPortActSysId | read-only | current | LACP port actor system ID |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.5 | ColumnlacpInfoPortActSysPrio | read-only | current | LACP port actor system priority |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.6 | ColumnlacpInfoPortActAdminKey | read-only | current | LACP port actor admin key |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.7 | ColumnlacpInfoPortActOperKey | read-only | current | LACP port actor oper key |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.8 | ColumnlacpInfoPortActPortNum | read-only | current | LACP port number |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.9 | ColumnlacpInfoPortActPortPrio | read-only | current | LACP port priority |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.10 | ColumnlacpInfoPortIndivState | read-only | current | LACP port individual state |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.11 | ColumnlacpInfoSelAggrId | read-only | current | LACP port selected aggregator ID |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.12 | ColumnlacpInfoAttAggrId | read-only | current | LACP port attached aggregator ID |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.13 | ColumnlacpInfoPortReadyN | read-only | current | True value for Ready_N flag indicates that the wait while timer has expired and it is waiting to attach to an aggregator. There is one Ready_N value for each p… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.14 | ColumnlacpInfoPortNtt | read-only | current | Need to transmit flag. True indicates that there is new protocol information that should be transmitted on the link. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.15 | ColumnlacpInfoPortSelected | read-only | current | Selected flag value indicates that the selection logic has selected an appropriate Aggregator. A value of unselected indicates that no aggregator is currently … |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.16 | ColumnlacpInfoPortMoved | read-only | current | Port Moved flag is set to true if the receive machine for a port is in the port_disabled state, and the combination of partner oper system and partner oper por… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.17 | ColumnlacpInfoCollDetState | read-only | current | LACP port collision and detection state |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.18 | ColumnlacpInfoPortRxState | read-only | current | LACP port RX machine state |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.19 | ColumnlacpInfoPortMuxState | read-only | current | LACP port Mux machine state |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.20 | ColumnlacpInfoPortPerState | read-only | current | LACP port periodic machine state |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.21 | ColumnlacpInfoPortPerTraTimer | read-only | current | Periodic Transmit Timer |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.22 | ColumnlacpInfoPortCurWhileTimer | read-only | current | Current While Timer |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.1.1.23 | ColumnlacpInfoPortOperState | read-only | current | The current operational state of LACP on the port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.2 | TablelacpInfoPortAdminTable | not-accessible | current | The table of LACP port admin information. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.2.1 | RowlacpInfoPortAdminTableEntry | not-accessible | current | Admin information about a LACP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.2.1.1 | ColumnlacpInfoPortAdminIndex | read-only | current | The port identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.2.1.7 | ColumnlacpInfoPortActAdPortState | read-only | current | The state of Actor Administrator Port. This is a octet mask with the following bits: Activity, Synchronization, Defaulted, Timeout, Collecting, Expired, Aggreg… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.2.1.8 | ColumnlacpInfoPortActAdActiv | read-only | current | The state of Actor Administrator Port Activity |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.2.1.9 | ColumnlacpInfoPortActAdSync | read-only | current | The state of Actor Administrator Port Synchronization |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.2.1.10 | ColumnlacpInfoPortActAdDef | read-only | current | The state of Actor Administrator Port Defaulted |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.2.1.11 | ColumnlacpInfoPortActAdTimeout | read-only | current | The state of Actor Administrator Port Timeout |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.2.1.12 | ColumnlacpInfoPortActAdColl | read-only | current | The state of Actor Administrator Port Collecting |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.2.1.13 | ColumnlacpInfoPortActAdExp | read-only | current | The state of Actor Administrator Port Expired |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.2.1.14 | ColumnlacpInfoPortActAdAggr | read-only | current | The state of Actor Administrator Port Aggregation |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.2.1.15 | ColumnlacpInfoPortActAdDist | read-only | current | The state of Actor Administrator Port Distributing |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3 | TablelacpInfoPortOperTable | not-accessible | current | The table of LACP port oper information. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1 | RowlacpInfoPortOperTableEntry | not-accessible | current | Oper information about a LACP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.1 | ColumnlacpInfoPortOperIndex | read-only | current | The port identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.2 | ColumnlacpInfoPortPartOpSysPrio | read-only | current | The value of Partner Operator Port System Priority |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.3 | ColumnlacpInfoPortPartOpSysId | read-only | current | The value of Partner Operator Port System ID |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.4 | ColumnlacpInfoPortPartOpKey | read-only | current | The value of Partner Operator Port Key |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.5 | ColumnlacpInfoPortPartOpPortNum | read-only | current | The Partner Operator Port Number |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.6 | ColumnlacpInfoPortPartOpPortPrio | read-only | current | The value of Partner Operator Port Priority |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.7 | ColumnlacpInfoPortActOpPortState | read-only | current | The state of Actor Operator Port. This is a octet mask with the following bits: Activity, Synchronization, Defaulted, Timeout, Collecting, Expired, Aggregation… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.8 | ColumnlacpInfoPortActOpActiv | read-only | current | The state of Actor Operator Port Activity |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.9 | ColumnlacpInfoPortActOpSync | read-only | current | The state of Actor Operator Port Synchronization |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.10 | ColumnlacpInfoPortActOpDef | read-only | current | The state of Actor Operator Port Defaulted |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.11 | ColumnlacpInfoPortActOpTimeout | read-only | current | The state of Actor Operator Port Timeout |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.12 | ColumnlacpInfoPortActOpColl | read-only | current | The state of Actor Operator Port Collecting |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.13 | ColumnlacpInfoPortActOpExp | read-only | current | The state of Actor Operator Port Expired |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.14 | ColumnlacpInfoPortActOpAggr | read-only | current | The state of Actor Operator Port Aggregation |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.15 | ColumnlacpInfoPortActOpDist | read-only | current | The state of Actor Operator Port Distributing |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.16 | ColumnlacpInfoPortPartOpPortState | read-only | current | The state of Partner Operator Port. This is a octet mask with the following bits: Activity, Synchronization, Defaulted, Timeout, Collecting, Expired, Aggregati… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.17 | ColumnlacpInfoPortPartOpActiv | read-only | current | The state of Partner Operator Port Activity |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.18 | ColumnlacpInfoPortPartOpSync | read-only | current | The state of Partner Operator Port Synchronization |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.19 | ColumnlacpInfoPortPartOpDef | read-only | current | The state of Partner Operator Port Defaulted |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.20 | ColumnlacpInfoPortPartOpTimeout | read-only | current | The state of Partner Operator Port Timeout |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.21 | ColumnlacpInfoPortPartOpColl | read-only | current | The state of Partner Operator Port Collecting |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.22 | ColumnlacpInfoPortPartOpExp | read-only | current | The state of Partner Operator Port Expired |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.23 | ColumnlacpInfoPortPartOpAggr | read-only | current | The state of Partner Operator Port Aggregation |
| 1.3.6.1.4.1.26543.2.7.7.2.3.3.2.3.1.24 | ColumnlacpInfoPortPartOpDist | read-only | current | The state of Partner Operator Port Distributing |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4 | NodecistInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.1 | NodecistGeneralInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.1.1 | ScalarcistRoot | read-only | current | The bridge identifier of the Root of the common spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the C… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.1.2 | ScalarcistRootPathCost | read-only | current | The cost of the path to the CIST Root as seen from this bridge. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.1.3 | ScalarcistRootPortIndex | read-only | current | The Port Number of the Port which offers the lowest path cost from this bridge to the CIST Root Bridge. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.1.4 | ScalarcistBridgeHelloTime | read-only | current | The amount of time between the transmission of Configuration bridge PDUs in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.1.5 | ScalarcistBridgeMaxAge | read-only | current | The value in seconds that all bridges use for MaxAge when this bridge is acting as the root. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.1.6 | ScalarcistBridgeForwardDelay | read-only | current | The value in seconds that all bridges use for ForwardDelay when this bridge is acting as the root. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.1.7 | ScalarcistRegionalRoot | read-only | current | The bridge identifier of the Root of the Multiple spanning tree region as determined by the Spanning Tree Protocol as executed by this node. This value is used… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.1.8 | ScalarcistRegionalPathCost | read-only | current | The Cost of the path to the CIST Regional Root as seen from this bridge. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.1.9 | ScalarmstpDigest | read-only | current | The digest of the mstp. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.2 | TablecistInfoPortTable | not-accessible | current | The table of CIST Port information. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.2.1 | RowcistInfoPortTableEntry | not-accessible | current | Information about a particular CIST Port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.2.1.1 | ColumncistInfoPortIndex | read-only | current | The port number of the port for which this entry contains spanning tree configuration. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.2.1.2 | ColumncistInfoPortPriority | read-only | current | The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting this value. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.2.1.3 | ColumncistInfoPortPathCost | read-only | current | The contribution of this port to the path cost of paths towards the CIST Root which include this port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.2.1.4 | ColumncistInfoPortState | read-only | current | Current state of the Port as defined by the Common spanning tree protocol. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.2.1.5 | ColumncistInfoPortRole | read-only | current | Selected Port Role of the port for this spanning tree instance. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.2.1.6 | ColumncistInfoPortDesignatedBridge | read-only | current | The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.2.1.7 | ColumncistInfoPortDesignatedPort | read-only | current | The Port identifier of the port on the Designated Bridge for this port's segment. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.2.1.8 | ColumncistInfoPortLinkType | read-only | current | The point-to-point status of the LAN segment attached to this port. A value of p2p (1) indicates that this port is being treated as if it is connected to a poi… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.2.1.9 | ColumncistInfoPortHelloTime | read-only | current | CIST port Hello Time |
| 1.3.6.1.4.1.26543.2.7.7.2.3.4.2.1.10 | ColumncistInfoPortEdge | read-only | current | The port is an edge port or not. Returns disabled(2) when the port is not an edge port and returns enabled(1) when it is an edge port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.5 | NodevlanInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.5.1 | TablevlanInfoTable | not-accessible | current | The table of VLAN information. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.5.1.1 | RowvlanInfoTableEntry | not-accessible | current | Information about a particular VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.5.1.1.1 | ColumnvlanInfoId | read-only | current | The VLAN identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.5.1.1.2 | ColumnvlanInfoName | read-only | current | The VLAN name. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.5.1.1.3 | ColumnvlanInfoStatus | read-only | current | Enable or disable, VLAN state information |
| 1.3.6.1.4.1.26543.2.7.7.2.3.5.1.1.7 | ColumnvlanInfoPorts | read-only | current | The port list information in the VLAN. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ por… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.6 | Nodedot1xInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.6.1 | Tabledot1xInfoPortTable | not-accessible | current | The table of 8021x configuration in the Current_config. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.6.1.1 | Rowdot1xInfoPortEntry | not-accessible | current | Information about 8021x Port Config |
| 1.3.6.1.4.1.26543.2.7.7.2.3.6.1.1.1 | Columndot1xInfoPortIndex | read-only | current | The 8021x Port number for which the table is related. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.6.1.1.2 | Columndot1xInfoPortAuthMode | read-only | current | Authentication mode |
| 1.3.6.1.4.1.26543.2.7.7.2.3.6.1.1.3 | Columndot1xInfoPortAuthStatus | read-only | current | Authentication status |
| 1.3.6.1.4.1.26543.2.7.7.2.3.6.1.1.5 | Columndot1xInfoPortAuthPAEState | read-only | current | Authenticator PAE State |
| 1.3.6.1.4.1.26543.2.7.7.2.3.6.1.1.6 | Columndot1xInfoPortBackAuthState | read-only | current | Backend authenticator PAE state |
| 1.3.6.1.4.1.26543.2.7.7.2.3.6.1.1.7 | Columndot1xInfoPortAssignedVlan | read-only | current | Vlan assigned from radius server.Value of 0 indicates , no vlan assigned via Radius |
| 1.3.6.1.4.1.26543.2.7.7.2.3.6.2 | Nodedot1xSystemInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.6.2.1 | Scalardot1xSystemCapability | read-only | current | System capability |
| 1.3.6.1.4.1.26543.2.7.7.2.3.6.2.2 | Scalardot1xSystemStatus | read-only | current | System status |
| 1.3.6.1.4.1.26543.2.7.7.2.3.6.2.3 | Scalardot1xSystemProtoVersion | read-only | current | Protocol version |
| 1.3.6.1.4.1.26543.2.7.7.2.3.7 | NodegenInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.9 | NodetrunkGroupInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.9.1 | TabletrunkGroupInfoTable | not-accessible | current | The table of trunk group information. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.9.1.1 | RowtrunkGroupInfoTableEntry | not-accessible | current | A row in trunk group information table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.9.1.1.1 | ColumntrunkGroupInfoIndex | read-only | current | The identifier of the trunk group. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.9.1.1.2 | ColumntrunkGroupInfoState | read-only | current | Trunk group state. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.9.1.1.3 | ColumntrunkGroupInfoPorts | read-only | current | The port list in the trunk group. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 |… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.9.1.1.4 | ColumntrunkGroupInfoProtocol | read-only | current | Trunk group protocol Static - static trunk group Lacp - dynamic trunk group |
| 1.3.6.1.4.1.26543.2.7.7.2.3.9.2 | TabletrunkGroupInfoPortTable | not-accessible | current | The table of Trunk Group Info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.9.2.1 | RowtrunkGroupInfoPortTableEntry | not-accessible | current | A row in the Trunk Info table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.9.2.1.1 | ColumntrunkGroupInfoPortTrunkId | read-only | current | The Trunk identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.9.2.1.2 | ColumntrunkGroupInfoPortPortId | read-only | current | The Port identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.9.2.1.3 | ColumntrunkGroupInfoPortStatus | read-only | current | The Port Status. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.10 | NodehotlinksInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.10.1 | ScalarhotlinksInfoOnState | read-only | current | Hot Links ON/OFF setting info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.10.2 | ScalarhotlinksInfoFdbUpdateState | read-only | current | Enable/disable Hot Links FDB Update setting info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.10.3 | TablehotlinksInfoTriggerTable | not-accessible | current | The Hot Links Trigger Table Info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.10.3.1 | RowhotlinksInfoTriggerTableEntry | not-accessible | current | A row in the Hot Links Trigger Table Info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.10.3.1.1 | ColumnhotlinksInfoTriggerId | read-only | current | The Trigger identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.10.3.1.2 | ColumnhotlinksInfoTriggerName | read-only | current | A textual string containing the trigger name. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.10.3.1.3 | ColumnhotlinksInfoTriggerState | read-only | current | Enable/disable Trigger state info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.10.3.1.4 | ColumnhotlinksInfoTriggerPreemptState | read-only | current | Enable/disable Preemption state info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.10.3.1.5 | ColumnhotlinksInfoTriggerFdelay | read-only | current | Forward Delay setting info (in secs). |
| 1.3.6.1.4.1.26543.2.7.7.2.3.10.3.1.6 | ColumnhotlinksInfoTriggerActive | read-only | current | A textual string containing the active interface info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.10.4 | ScalarhotlinksInfoBpduState | read-only | current | Enable/disable Hot Links BPDU flood setting info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.10.5 | ScalarhotlinksInfoFdbUpdateRate | read-only | current | Hot Links FDB update rate (packets per second). |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11 | NodelldpInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1 | TablelldpInfoPortTable | not-accessible | current | The table of LLDP Port Info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1 | RowlldpInfoPortEntry | not-accessible | current | LLDP Port Info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.1 | ColumnlldpInfoPortIndex | read-only | current | The index of the row in LLDP info port table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.2 | ColumnlldpInfoPortAlias | read-only | current | The port alias of the port in LLDP info port table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.3 | ColumnlldpInfoPortMacAddress | read-only | current | The mac address of the port in LLDP info port table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.4 | ColumnlldpInfoPortMtu | read-only | current | The MTU size of the port in LLDP info port table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.5 | ColumnlldpInfoPortEnabled | read-only | current | The PortEnabled field of the port in LLDP info port table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.6 | ColumnlldpInfoPortAdminStatus | read-only | current | The Admin Status of the port in LLDP info port table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.7 | ColumnlldpInfoPortRxChanges | read-only | current | The rxChanges field of the port in LLDP info port table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.8 | ColumnlldpInfoPortportdesctlv | read-only | current | This is the Port Description TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.9 | ColumnlldpInfoPortsysnametlv | read-only | current | This is the System Name TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.10 | ColumnlldpInfoPortsysdescrtlv | read-only | current | This is the System Description TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.11 | ColumnlldpInfoPortsyscaptlv | read-only | current | This is the System Capabilities TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.12 | ColumnlldpInfoPortmgmtaddrtlv | read-only | current | This is the Management Address TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.13 | ColumnlldpInfoPortportvidtlv | read-only | current | This is the Port VLAN ID TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.14 | ColumnlldpInfoPortportprottlv | read-only | current | This is the Port and Protocol VLAN ID TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.15 | ColumnlldpInfoPortvlannametlv | read-only | current | This is the VLAN Name TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.16 | ColumnlldpInfoPortprotidtlv | read-only | current | This is the Protocol Identity TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.17 | ColumnlldpInfoPortmacphytlv | read-only | current | This is the MAC/PHY Configuration/Status TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.18 | ColumnlldpInfoPortpowermditlv | read-only | current | This is the Power Via MDI TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.19 | ColumnlldpInfoPortlinkaggrtlv | read-only | current | This is the Link Aggregation TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.20 | ColumnlldpInfoPortframesztlv | read-only | current | This is the Maximum Frame Size TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.1.1.22 | ColumnlldpInfoPortevbtlv | read-only | current | This is the EVB TLV state of the LLDP port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.2 | TablelldpInfoTxTable | not-accessible | current | The table of LLDP Transmit State Machine Info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.2.1 | RowlldpInfoTxEntry | not-accessible | current | LLDP Transmit State Machine Info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.2.1.1 | ColumnlldpInfoTxIndex | read-only | current | The index of the row in LLDP Transmit State Machine info table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.2.1.2 | ColumnlldpInfoTxState | read-only | current | The transmit state of the port in LLDP Transmit State Machine. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.2.1.3 | ColumnlldpInfoTxLocalChanged | read-only | current | The somethingChangedLocal field of the port in LLDP Transmit State Machine. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.2.1.4 | ColumnlldpInfoTxTTL | read-only | current | The txTTL timer of the port in LLDP Transmit State Machine. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.2.1.5 | ColumnlldpInfoTxTxTTR | read-only | current | The txTTR timer of the port in LLDP Transmit State Machine. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.2.1.6 | ColumnlldpInfoTxDelayWhile | read-only | current | The txDelayWhile timer of the port in LLDP Transmit State Machine. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.2.1.7 | ColumnlldpInfoTxShutdownWhile | read-only | current | The txShutdownWhile timer of the port in LLDP Transmit State Machine. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.2.1.8 | ColumnlldpInfoTxReinitDelay | read-only | current | The reinitDelay timer of the port in LLDP Transmit State Machine. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.2.1.9 | ColumnlldpInfoTxHoldMultiplier | read-only | current | The msgTxHold timer of the port in LLDP Transmit State Machine. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.2.1.10 | ColumnlldpInfoTxTransmitInterval | read-only | current | The msgTxInterval timer of the port in LLDP Transmit State Machine. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.2.1.11 | ColumnlldpInfoTxTransmitDelay | read-only | current | The txDelay timer of the port in LLDP Transmit State Machine. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.2.1.12 | ColumnlldpInfoTxDMAC | read-only | current | The Destination MAC address of the LLDP remote devices. Legend(possible values in DMAC column) : NB - Nearest Bridge - 01-80-C2-00-00-0E NnTB - Nearest non-TPM… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.3 | TablelldpInfoRxTable | not-accessible | current | The table of LLDP Receive State Machine Info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.3.1 | RowlldpInfoRxEntry | not-accessible | current | LLDP Receive State Machine Info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.3.1.1 | ColumnlldpInfoRxIndex | read-only | current | The index of the row in LLDP Receive State Machine info table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.3.1.2 | ColumnlldpInfoRxState | read-only | current | The receive state of the port in LLDP Receive State Machine. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.3.1.3 | ColumnlldpInfoRxBadFrame | read-only | current | The badFrame field of the port in LLDP Receive State Machine. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.3.1.4 | ColumnlldpInfoRxRcvFrame | read-only | current | The rcvFrame field of the port in LLDP Receive State Machine. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.3.1.5 | ColumnlldpInfoRxRxInfoAge | read-only | current | The rxInfoAge field of the port in LLDP Receive State Machine. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.3.1.6 | ColumnlldpInfoRxRemoteChanged | read-only | current | The somethingChangedRemote field of the port in LLDP Receive State Machine. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.3.1.7 | ColumnlldpInfoRxTooManyNeighbors | read-only | current | The tooManyNeighbors field of the port in LLDP Receive State Machine. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.3.1.8 | ColumnlldpInfoRxSNMPNotify | read-only | current | The tooManyNeighbors field of the port in LLDP Receive State Machine. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.3.1.9 | ColumnlldpInfoRxRxTTL | read-only | current | The rxTTL timer of the port in LLDP Receive State Machine. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.3.1.10 | ColumnlldpInfoRxTooManyNeighborTimer | read-only | current | The tooManyNeighborsTimer timer of the port in LLDP Receive State Machine. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.3.1.11 | ColumnlldpInfoRxDMAC | read-only | current | The Destination MAC address of the LLDP remote devices. Legend(possible values in DMAC column) : NB - Nearest Bridge - 01-80-C2-00-00-0E NnTB - Nearest non-TPM… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.4 | TablelldpInfoRemoteDevicesTable | not-accessible | current | The table of LLDP remote devices Info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.4.1 | RowlldpInfoRemoteDevicesEntry | not-accessible | current | LLDP remote devices Info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.4.1.1 | ColumnlldpInfoRemoteDevicesIndex | read-only | current | The index of the row in LLDP remote devices info table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.4.1.3 | ColumnlldpInfoRemoteDevicesRemoteTTL | read-only | current | The remote TTL of the LLDP remote devices entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.4.1.4 | ColumnlldpInfoRemoteDevicesRxChanges | read-only | current | The rxChanges field of the LLDP remote devices entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.4.1.5 | ColumnlldpInfoRemoteDevicesLocalPort | read-only | current | The local port alias of the LLDP remote devices entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.4.1.6 | ColumnlldpInfoRemoteDevicesChassisSubtype | read-only | current | The chassis ID subtype of the LLDP remote devices entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.4.1.7 | ColumnlldpInfoRemoteDevicesChassisId | read-only | current | The chassis ID of the LLDP remote devices entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.4.1.8 | ColumnlldpInfoRemoteDevicesPortSubtype | read-only | current | The port ID subtype of the LLDP remote devices entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.4.1.9 | ColumnlldpInfoRemoteDevicesPortId | read-only | current | The port ID of the LLDP remote devices entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.4.1.10 | ColumnlldpInfoRemoteDevicesSystemName | read-only | current | The system name of the LLDP remote devices entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.4.1.11 | ColumnlldpInfoRemoteDevicesSystemDescription | read-only | current | The system description of the LLDP remote devices entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.4.1.12 | ColumnlldpInfoRemoteDevicesPortDescription | read-only | current | The port description of the LLDP remote devices entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.4.1.13 | ColumnlldpInfoRemoteDevicesSystemCapSupported | read-only | current | The supported system capabilities of the LLDP remote devices entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.4.1.14 | ColumnlldpInfoRemoteDevicesSystemCapEnabled | read-only | current | The enabled system capabilities of the LLDP remote devices entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.4.1.15 | ColumnlldpInfoRemoteDMAC | read-only | current | The Destination MAC address of the LLDP remote devices. Legend(possible values in DMAC column) : NB - Nearest Bridge - 01-80-C2-00-00-0E NnTB - Nearest non-TPM… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.5 | TablelldpInfoRemoteDevicesManAddrTable | not-accessible | current | The table of LLDP remote devices management address Info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.5.1 | RowlldpInfoRemoteDevicesManAddrEntry | not-accessible | current | LLDP remote devices management address Info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.5.1.1 | ColumnlldpInfoRemoteDevicesManAddrSubtype | read-only | current | The management address subtype of the LLDP remote devices entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.5.1.2 | ColumnlldpInfoRemoteDevicesManAddr | read-only | current | The management address of the LLDP remote devices entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.5.1.3 | ColumnlldpInfoRemoteDevicesManAddrIfSubtype | read-only | current | The interface numbering subtype of the LLDP remote devices management address entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.5.1.4 | ColumnlldpInfoRemoteDevicesManAddrIfId | read-only | current | The interface number of the LLDP remote devices management address entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.5.1.5 | ColumnlldpInfoRemoteDevicesManAddrOID | read-only | current | The object identifier of the LLDP remote devices management address entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.6 | ScalarlldpClearMsap | read-write | current | Clear LLDP remote devices information when setting clearMsap(1). When read, ok(0) is always returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.7 | TableevbTLVInfoTable | not-accessible | current | The table of ECDP TLV Info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.7.1 | RowevbTLVInfoEntry | not-accessible | current | Information about EVB TLV. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.7.1.1 | ColumnevbTLVInfoEntryIndex | read-only | current | The index of the vsi info table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.7.1.2 | ColumnevbPortIndex | read-only | current | The evb tlv port info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.7.1.3 | ColumnevbLocalCapability | read-only | current | The local evb tlv capabilityinfo. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.7.1.4 | ColumnevbLocalCurrent | read-only | current | The local evb tlv current info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.7.1.5 | ColumnevbLocalRTEVal | read-only | current | The local evb tlv ECP RTE info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.7.1.6 | ColumnevbRemoteCapability | read-only | current | The remote evb tlv capability nfo. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.7.1.7 | ColumnevbRemoteCurrent | read-only | current | The remote evb tlv cuurent info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.11.7.1.8 | ColumnevbRemoteRTEVal | read-only | current | The remote evb tlv ECP RTE info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.12 | NodeoamInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.12.1 | TableoamInfoPortTable | not-accessible | current | The table of OAM port information. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.12.1.1 | RowoamInfoPortEntry | not-accessible | current | Information about OAM Port |
| 1.3.6.1.4.1.26543.2.7.7.2.3.12.1.1.1 | ColumnoamInfoPortIndex | read-only | current | The OAM Port number for which the table is related. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.12.1.1.2 | ColumnoamInfoPortLocalState | read-only | current | OAM local port state |
| 1.3.6.1.4.1.26543.2.7.7.2.3.12.1.1.3 | ColumnoamInfoPortLocalMode | read-only | current | OAM local port mode |
| 1.3.6.1.4.1.26543.2.7.7.2.3.12.1.1.4 | ColumnoamInfoPortLocalLinkStatus | read-only | current | OAM local port link status |
| 1.3.6.1.4.1.26543.2.7.7.2.3.12.1.1.5 | ColumnoamInfoPortLocalStable | read-only | current | OAM local port stable |
| 1.3.6.1.4.1.26543.2.7.7.2.3.12.1.1.6 | ColumnoamInfoPortLocalSatisfied | read-only | current | OAM local port satisfied |
| 1.3.6.1.4.1.26543.2.7.7.2.3.12.1.1.7 | ColumnoamInfoPortLocalEvaluating | read-only | current | OAM local port evaluating |
| 1.3.6.1.4.1.26543.2.7.7.2.3.12.1.1.8 | ColumnoamInfoPortRemoteMode | read-only | current | OAM remote port mode |
| 1.3.6.1.4.1.26543.2.7.7.2.3.12.1.1.9 | ColumnoamInfoPortRemoteMAC | read-only | current | OAM remote port MAC address |
| 1.3.6.1.4.1.26543.2.7.7.2.3.12.1.1.10 | ColumnoamInfoPortRemoteStable | read-only | current | OAM remote port stable |
| 1.3.6.1.4.1.26543.2.7.7.2.3.12.1.1.11 | ColumnoamInfoPortRemoteStateValid | read-only | current | OAM remote port state valid |
| 1.3.6.1.4.1.26543.2.7.7.2.3.12.1.1.12 | ColumnoamInfoPortRemoteEvaluating | read-only | current | OAM remote port evaluating |
| 1.3.6.1.4.1.26543.2.7.7.2.3.13 | NodeudldInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.13.1 | TableudldInfoPortTable | not-accessible | current | The table of UDLD port info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.13.1.1 | RowudldInfoPortEntry | not-accessible | current | A row inside UDLD port info table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.13.1.1.1 | ColumnudldInfoPortIndex | read-only | current | The index of the row in UDLD port configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.13.1.1.2 | ColumnudldInfoPortConfig | read-only | current | The Config field of the port in UDLD port info table. Shows the administative state of the current port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.13.1.1.3 | ColumnudldInfoPortMode | read-only | current | The Mode field of the port in UDLD info port table. Shows the udld administrative mode for the current port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.13.1.1.4 | ColumnudldInfoPortLink | read-only | current | The Link field of the port in UDLD info port table. Shows the state of the link associated with the port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.13.1.1.5 | ColumnudldInfoPortOperationalStatus | read-only | current | The OperationalStatus field of the port in UDLD info port table. Contains the udld operational state for the current port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.13.1.1.6 | ColumnudldInfoPortBidirectionalStatus | read-only | current | The BidirectionalStatus field of the port in UDLD info port table. Contains the udld bidirectional state for the current port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.13.1.1.7 | ColumnudldInfoPortInterval | read-only | current | The Interval field of the port in UDLD info port table. The duration, measured in seconds, of the interval during which UDLD probes are sent, after the linkup … |
| 1.3.6.1.4.1.26543.2.7.7.2.3.13.1.1.8 | ColumnudldInfoPortTimeout | read-only | current | The Timeout field of the port in UDLD info port table. Length of the detection phase, measured in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.13.1.1.9 | ColumnudldInfoPortNeighborCount | read-only | current | The Neighbor field of the port in UDLD info port table. Contains the number of udld neighbors for the current port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.13.2 | TableudldInfoNeighborTable | not-accessible | current | The table of UDLD port neighbor info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.13.2.1 | RowudldInfoNeighborEntry | not-accessible | current | A row inside UDLD port info table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.13.2.1.1 | ColumnudldInfoNeighborLocalPortIndex | read-only | current | The index of the port for which neighbor information will be returned. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.13.2.1.2 | ColumnudldInfoNeighborIndex | read-only | current | The index of the target neighbor among the port neighbors. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.13.2.1.3 | ColumnudldInfoNeighborExpiration | read-only | current | Hold time for the given neighbor. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.13.2.1.4 | ColumnudldInfoNeighborDeviceName | read-only | current | Device name reported by neigbor. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.13.2.1.5 | ColumnudldInfoNeighborDeviceID | read-only | current | Device ID reported by neigbor. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.13.2.1.6 | ColumnudldInfoNeighborPortID | read-only | current | Port ID reported by neigbor. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14 | NodefailoverInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.1 | ScalarfailoverInfoState | read-only | current | Current state of failover |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.3 | TablefailoverInfoTriggerTable | not-accessible | current | This table holds the information for individual triggers |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.3.1 | RowfailoverInfoTriggerEntry | not-accessible | current | A row in the failover trigger table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.3.1.1 | ColumnfailoverInfoTriggerId | read-only | current | The trigger identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.3.1.2 | ColumnfailoverInfoTriggerState | read-only | current | The trigger state. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.3.1.3 | ColumnfailoverInfoTriggerLimit | read-only | current | Limit number of operational links |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.3.1.4 | ColumnfailoverInfoTriggerMonitorState | read-only | current | The runtime monitor state |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.3.1.5 | ColumnfailoverInfoTriggerMonitorPorts | read-only | current | The list of ports that are monitored. The ports are represented in bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ por… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.3.1.6 | ColumnfailoverInfoTriggerControlState | read-only | current | The runtime control state |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.3.1.7 | ColumnfailoverInfoTriggerControlPorts | read-only | current | The list of ports that are controlled. The ports are represented in bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ po… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.4 | TablefailoverInfoMonPortStateTable | not-accessible | current | This table holds the information for individual triggers |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.4.1 | RowfailoverInfoTriggerMonPortEntry | not-accessible | current | A row in the failover trigger table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.4.1.1 | ColumnfailoverInfoTriggerMonId | read-only | current | The trigger identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.4.1.2 | ColumnfailoverInfoTriggerMonPortId | read-only | current | The Port identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.4.1.3 | ColumnfailoverInfoTriggerMonPortStatus | read-only | current | The Port Status. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.5 | TablefailoverInfoCtlPortStateTable | not-accessible | current | This table holds the information for individual triggers |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.5.1 | RowfailoverInfoTriggerCtlPortEntry | not-accessible | current | A row in the failover trigger table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.5.1.1 | ColumnfailoverInfoTriggerCtlId | read-only | current | The trigger identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.5.1.2 | ColumnfailoverInfoTriggerCtlPortId | read-only | current | The Port identifier. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.14.5.1.3 | ColumnfailoverInfoTriggerCtlPortStatus | read-only | current | The Port Status. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16 | NodevlagInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.1 | NodevlagInfoSystem | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.1.1 | ScalarvlagInfoState | read-only | current | The current running state of vLAG. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.1.2 | ScalarvlagInfoAdminRole | read-only | current | The current running role of the switch. Role can be Primary(1), secondary(2) and unelected(3). Primary role indicates that the this switch controls the central… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.1.3 | ScalarvlagInfoISLId | read-only | current | vLAG ISL trunk id. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.1.4 | ScalarvlagInfoLocalMac | read-only | current | Local vLAG MAC address. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.1.5 | ScalarvlagInfoLocalPriority | read-only | current | Local vLAG Priority. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.1.6 | ScalarvlagInfoRemoteMac | read-only | current | Remote vLAG MAC address. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.1.7 | ScalarvlagInfoRemotePriority | read-only | current | Remote vLAG Priority. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.1.8 | ScalarvlagInfoHlthchkStatus | read-only | current | The current health check running status. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.1.9 | ScalarvlagInfoStartupDelayInterval | read-only | current | Startup Delay Timer Interval. The value may be different from vlagCurCfgStartupDelayInterval for the configuration of the interval after the timer is started c… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.1.10 | ScalarvlagInfoStartupDelayStatus | read-only | current | Startup Delay Timer Status. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.1.11 | ScalarvlagInfoSystemMac | read-only | current | System vLAG MAC address |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.1.12 | ScalarvlagInfoOperaRole | read-only | current | vLAG switch operational role. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.1.13 | ScalarvlagInfoAutoRecoveryInterval | read-only | current | Auto Recovery Timer Interval. The value may be different from vlagCurCfgAutoRecoveryInterval for the configuration of the interval after the timer is started c… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.1.14 | ScalarvlagInfoAutoRecoveryStatus | read-only | current | Auto Recovery Timer Status. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.2 | NodevlagInfoGroup | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.2.1 | TablevlagInfoInstanceTable | not-accessible | current | A table of objects of the running vLAG instances. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.2.1.1 | RowvlagInfoInstanceEntry | not-accessible | current | The configuration objects for an vLAG group. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.2.1.1.1 | ColumnvlagInstanceId | read-only | current | The identifier of this instance. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.2.1.1.2 | ColumnvlagInstanceTrunkId | read-only | current | The trunk id of this vLAG instance. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.2.1.1.3 | ColumnvlagInstanceAdminKey | read-only | current | AdminKey of this vLAG instance. Applicable only incase of dynamic trunks. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.2.1.1.4 | ColumnvlagInstanceState | read-only | current | The current running state of the vLAG instance. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.2.2 | NodevlagInfoIslGroup | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.2.2.1 | ScalarvlagInfoIslId | read-only | current | vLAG ISL Id |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.2.2.3 | ScalarvlagInfoIslProtocol | read-only | current | vLAG ISL trunk group state Static - static trunk group Lacp - dynamic trunk group |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.2.2.4 | ScalarvlagInfoIslPortchannel | read-only | current | vLAG ISL portchannel number |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.2.2.5 | ScalarvlagInfoIslAdminkey | read-only | current | vLAG ISL lacp admin key |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.2.2.6 | ScalarvlagInfoIslPorts | read-only | current | The port list that forms the ISL. The ports are presented in bitmap format. OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.2.2.7 | ScalarvlagInfoIslPortState | read-only | current | The ISL member ports' protocol state. The ports' protocol state are presented in bitmap format. OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 |… |
| 1.3.6.1.4.1.26543.2.7.7.2.3.16.2.2.8 | ScalarvlagInfoIslPortLinkState | read-only | current | The ISL member ports' link state. The ports' link state are presented in bitmap format. OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || … |
| 1.3.6.1.4.1.26543.2.7.7.2.3.17 | NodeecpInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.17.1 | TableecpChnlInfoTable | not-accessible | current | The table of ECP channel Info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.17.1.1 | RowecpChnlInfoEntry | not-accessible | current | Information about ECP channel. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.17.1.1.1 | ColumnecpChnlInfoEntryIndex | read-only | current | The index of the ecp chnl info table. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.17.1.1.2 | ColumnecpChnlPortIndex | read-only | current | The ecp channel port info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.17.1.1.3 | ColumnecpChnlStag | read-only | current | The ecp channel stag info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.17.1.1.4 | ColumnecpChnlSndlen | read-only | current | The ecp channel send length info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.17.1.1.5 | ColumnecpChnlSndnxt | read-only | current | The ecp channel send next info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.17.1.1.6 | ColumnecpChnlRcvlast | read-only | current | The ecp channel recv last sequence info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.17.1.1.7 | ColumnecpChnlStateMachine | read-only | current | The ecp channel state machineinfo. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.17.1.1.8 | ColumnecpChnlRxCnt | read-only | current | The ecp channel Rx count info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.17.1.1.9 | ColumnecpChnlTxCnt | read-only | current | The ecp channel Tx count info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.17.1.1.10 | ColumnecpChnlRxDrop | read-only | current | The ecp channel RxDrop info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.17.1.1.11 | ColumnecpChnlTxDrop | read-only | current | The ecp channel TxDrop info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.17.1.1.12 | ColumnecpChnlState | read-only | current | The ecp channel state info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.17.1.1.13 | ColumnecpChnlAckErr | read-only | current | The ecp channel ACK error info. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.18 | NodeslpInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.1 | NodeslpInfoSystem | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.1.1 | ScalarslpInfoProtocolVersion | read-only | current | SLP protocol version. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.1.2 | ScalarslpInfoListeningPort | read-only | current | SLP listening port. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.1.3 | TableslpInfoListeningIPInterfaceTable | not-accessible | current | A table with all the SLP listening IP interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.1.3.1 | RowslpInfoListeningIPInterfaceEntry | not-accessible | current | The configuration objects for a SLP listening IP interface. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.1.3.1.1 | ColumnlisteningIPInterfaceId | read-only | current | The identifier of this IP interface. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.1.3.1.2 | ColumnlisteningIPInterfaceAddress | read-only | current | The adddress of this IP interface. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.2 | NodeslpInfoDirectoryAgents | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.2.1 | TableslpInfoDirectoryAgentsTable | not-accessible | current | A table with all the SLP Directory Agents. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.2.1.1 | RowslpInfoDirectoryAgentEntry | not-accessible | current | The configuration objects for a Directory Agent entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.2.1.1.1 | ColumndirectoryAgentAddress | read-only | current | The IP adddress of this Directory Agent. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.2.1.1.2 | ColumndirectoryAgentPort | read-only | current | The port of this Directory Agent. Communication can be done using TCP or UDP. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.2.1.1.3 | ColumndirectoryAgentTime | read-only | current | The time elapsed from the moment when this Directory Agent was learned measured in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.3 | NodeslpInfoUserAgents | |||
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.3.1 | TableslpInfoUserAgentsTable | not-accessible | current | A table with all the SLP User Agents. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.3.1.1 | RowslpInfoUserAgentEntry | not-accessible | current | The configuration objects for a User Agent entry. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.3.1.1.1 | ColumnuserAgentAddress | read-only | current | The IP adddress of this User Agent. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.3.1.1.2 | ColumnuserAgentPort | read-only | current | The port of this User Agent. Communication can be done using TCP or UDP. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.3.1.1.3 | ColumnuserAgentTime | read-only | current | The time elapsed from the moment when this User Agent was learned measured in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.2.3.18.4 | ScalarslpDirectoryAgentsClear | read-write | current | Setting this object to 'clear' will reset all directory agents settings of SLP. A get action of this object will always return 'other'. Setting this object to … |
| 1.3.6.1.4.1.26543.2.7.7.2.4 | Nodelayer2Oper | |||
| 1.3.6.1.4.1.26543.2.7.7.3 | Nodelayer3 | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1 | Nodelayer3Configs | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.1 | NodeipInterfaceCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.1 | ScalaripInterfaceTableMax | read-only | current | The maximum number of rows in the IP interface table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2 | TableipCurCfgIntfTable | not-accessible | current | The table of IP interface configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1 | RowipCurCfgIntfEntry | not-accessible | current | A row in the Ip interface table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.1 | ColumnipCurCfgIntfIndex | read-only | current | The interface number for which the IP information is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.2 | ColumnipCurCfgIntfAddr | read-only | current | This field configures the new IP/IPv6 addr of the interface. Address should be IPv4 dotted-quads or IPv6 16-byte hexadecimal colon notation. Valid IPv6 address… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.3 | ColumnipCurCfgIntfMask | read-only | current | The subnet mask as IPv4 dotted-quads OR the IPv6 prefix length (integer in range 0..128) associated with this IP address . |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.4 | ColumnipCurCfgIntfBroadcast | read-only | obsolete | The broadcast address of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.5 | ColumnipCurCfgIntfVlan | read-only | current | The VLAN associated with the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.6 | ColumnipCurCfgIntfState | read-only | current | The state of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.7 | ColumnipCurCfgIntfBootpRelay | read-only | current | Enable/disable BOOTP relay. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.12 | ColumnipCurCfgIntfRouteAdv | read-only | current | Enable/disable route advertisement of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.13 | ColumnipCurCfgIntfManagedCfg | read-only | current | Enable/disable Managed config flag of the interface, which allows the host to use DHCP for address configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.14 | ColumnipCurCfgIntfOtherCfg | read-only | current | Enable/disable Other config flag of the interface, which allows the host to use DHCP for other stateful configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.15 | ColumnipCurCfgIntfAdvLifetime | read-only | current | Set Router Advertisement lifetime of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.16 | ColumnipCurCfgIntfDadAttempts | read-only | current | Set the number of duplicate address detection (dad) attempts of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.17 | ColumnipCurCfgIntfReachTime | read-only | current | Set the advertised reachability time of the interface in ms. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.18 | ColumnipCurCfgIntfAdvInterval | read-only | current | Set the IPv6 Router Advertisement interval of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.19 | ColumnipCurCfgIntfAdvIntervalMin | read-only | current | Set the IPv6 Router Advertisement Minimum interval limit of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.20 | ColumnipCurCfgIntfRetransmitTimer | read-only | current | Set the IPv6 Router Advertisement Retransmit Timer in ms. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.21 | ColumnipCurCfgIntfHopLimit | read-only | current | Set the IPv6 Router Advertisement Current Hop Limit |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.22 | ColumnipCurCfgIntfAdvMtu | read-only | current | Enable/disable Advertise MTU option. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.23 | ColumnipCurCfgIntfIp6Host | read-only | current | Enable/disable IPv6 host mode on the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.25 | ColumnipCurCfgSecIntfAddr | read-only | current | This field configures the new IP/IPv6 addr of the interface. Address should be in IPv6 4-byte haxadecimal colon notation. Valid IPv6 address should be in any o… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.26 | ColumnipCurCfgSecIntfPrefix | read-only | current | The IPv6 prefix length (integer in range 0..128) associated with this IP address . |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.27 | ColumnipCurCfgIntfAnycast | read-only | current | This field has the value of anycast(1) if IPv6 interface address is anycast and none(2) if not. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.28 | ColumnipCurCfgSecIntfAnycast | read-only | current | This field has the value of anycast(1) if secondary IPv6 interface address is anycast and none(2) if not. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.2.1.29 | ColumnipCurCfgIntfIp6Dstun | read-only | current | Enable/disable sending of ICMP Unreachable messages. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3 | TableipNewCfgIntfTable | not-accessible | current | The table of interface in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1 | RowipNewCfgIntfEntry | not-accessible | current | A row in the Ip interface table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.1 | ColumnipNewCfgIntfIndex | read-only | current | The interface number for which the IP information is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.2 | ColumnipNewCfgIntfAddr | read-create | current | This field configures the new IP/IPv6 addr of the interface. Address should be IPv4 dotted-quads or IPv6 16-byte hexadecimal colon notation. Valid IPv6 address… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.3 | ColumnipNewCfgIntfMask | read-create | current | The subnet mask as IPv4 dotted-quads OR the IPv6 prefix length (integer in range 0..128) associated with this IP address . |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.5 | ColumnipNewCfgIntfVlan | read-create | current | The VLAN associated with the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.6 | ColumnipNewCfgIntfState | read-create | current | The state of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.7 | ColumnipNewCfgIntfDelete | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.8 | ColumnipNewCfgIntfBootpRelay | read-create | current | Enable/disable BOOTP relay. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.13 | ColumnipNewCfgIntfRouteAdv | read-create | current | Enable/disable route advertisement of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.14 | ColumnipNewCfgIntfManagedCfg | read-create | current | Enable/disable Managed config flag of the interface, which allows the host to use DHCP for address configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.15 | ColumnipNewCfgIntfOtherCfg | read-create | current | Enable/disable Other config flag of the interface, which allows the host to use DHCP for other stateful configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.16 | ColumnipNewCfgIntfAdvLifetime | read-create | current | Set Router Advertisement lifetime of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.17 | ColumnipNewCfgIntfDadAttempts | read-create | current | Set the number of duplicate address detection (dad) attempts of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.18 | ColumnipNewCfgIntfReachTime | read-create | current | Set the advertised reachability time of the interface in ms. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.19 | ColumnipNewCfgIntfAdvInterval | read-create | current | Set the IPv6 Router Advertisement interval of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.20 | ColumnipNewCfgIntfAdvIntervalMin | read-create | current | Set the IPv6 Router Advertisement Minimum interval limit of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.21 | ColumnipNewCfgIntfRetransmitTimer | read-create | current | Set the IPv6 Router Advertisement Retransmit Timer in ms. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.22 | ColumnipNewCfgIntfHopLimit | read-create | current | Set the IPv6 Router Advertisement Current Hop Limit |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.23 | ColumnipNewCfgIntfAdvMtu | read-create | current | Enable/disable Advertise MTU option. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.24 | ColumnipNewCfgIntfIp6Host | read-create | current | Enable/disable IPv6 host mode on the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.26 | ColumnipNewCfgSecIntfAddr | read-write | current | This field configures the new IPv6 addr of the interface. Address should be in IPv6 4-byte haxadecimal colon notation. Valid IPv6 address should be in any of t… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.27 | ColumnipNewCfgSecIntfPrefix | read-write | current | The IPv6 prefix length (integer in range 0..128) associated with this IP address . |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.28 | ColumnipNewCfgIntfAnycast | read-write | current | This field has the value of anycast(1) if IPv6 interface address is anycast and none(2) if not. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.29 | ColumnipNewCfgSecIntfAnycast | read-write | current | This field has the value of anycast(1) if secondary IPv6 interface address is anycast and none(2) if not. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.1.3.1.30 | ColumnipNewCfgIntfIp6Dstun | read-create | current | Enable/disable sending of ICMP Unreachable messages. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.2 | NodeipGatewayCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.2.3 | ScalaripGatewayTableMax | read-only | current | The maximum number of rows in the IP gateway table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.2.4 | TableipCurCfgGwTable | not-accessible | current | The table of gateways in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.2.4.1 | RowipCurCfgGwEntry | not-accessible | current | A row in the Ip gateway table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.2.4.1.1 | ColumnipCurCfgGwIndex | read-only | current | The gateway number for which the information is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.2.4.1.2 | ColumnipCurCfgGwAddr | read-only | current | The IP address of the default gateway. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.2.4.1.3 | ColumnipCurCfgGwInterval | read-only | current | The interval between ping attempts. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.2.4.1.4 | ColumnipCurCfgGwRetry | read-only | current | The number of failed attempts to declare the default gateway DOWN. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.2.4.1.5 | ColumnipCurCfgGwState | read-only | current | The state of the default gateway. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.2.4.1.6 | ColumnipCurCfgGwArp | read-only | current | The state of ARP only health checks. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.2.5 | TableipNewCfgGwTable | not-accessible | current | The table of gateway in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.2.5.1 | RowipNewCfgGwEntry | not-accessible | current | A row in the Ip default gateway table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.2.5.1.1 | ColumnipNewCfgGwIndex | read-only | current | The gateway number for which the information is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.2.5.1.2 | ColumnipNewCfgGwAddr | read-create | current | The IP address of the default gateway. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.2.5.1.3 | ColumnipNewCfgGwInterval | read-create | current | The interval in seconds between ping attempts. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.2.5.1.4 | ColumnipNewCfgGwRetry | read-create | current | The number of failed attempts to declare the default gateway DOWN. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.2.5.1.5 | ColumnipNewCfgGwState | read-create | current | The state of the default gateway. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.2.5.1.6 | ColumnipNewCfgGwDelete | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other is returned. Setting the value to anything other than 2(delete) has no effect … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.2.5.1.7 | ColumnipNewCfgGwArp | read-create | current | The state of the ARP only health checks. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3 | NodeipStaticRouteCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.1 | ScalaripStaticRouteTableMaxSize | read-only | current | The maximum number of rows in the Static Route table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.2 | TableipCurCfgStaticRouteTable | not-accessible | current | The table of static routes in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.2.1 | RowipCurCfgStaticRouteEntry | not-accessible | current | A row in the static IP route table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.2.1.1 | ColumnipCurCfgStaticRouteIndx | read-only | current | The index of the static routing table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.2.1.2 | ColumnipCurCfgStaticRouteDestIp | read-only | current | The destination IP address of this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.2.1.3 | ColumnipCurCfgStaticRouteMask | read-only | current | The current subnet mask of this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.2.1.4 | ColumnipCurCfgStaticRouteGateway | read-only | current | The current gateway of this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.2.1.5 | ColumnipCurCfgStaticRouteInterface | read-only | current | The IP interface of this route. The IP address of the specified interface shall be use as source IP when performs routing. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.3 | TableipNewCfgStaticRouteTable | not-accessible | current | The table of static routes in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.3.1 | RowipNewCfgStaticRouteEntry | not-accessible | current | A row in the static IP route table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.3.1.1 | ColumnipNewCfgStaticRouteIndx | read-only | current | The index of the static routing table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.3.1.2 | ColumnipNewCfgStaticRouteDestIp | read-create | current | The destination IP address of this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.3.1.3 | ColumnipNewCfgStaticRouteMask | read-create | current | The subnet mask of this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.3.1.4 | ColumnipNewCfgStaticRouteGateway | read-create | current | The IP address of the gateway for this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.3.1.5 | ColumnipNewCfgStaticRouteAction | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other is returned. Setting the value to anything other than 2(delete) has no effect … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.3.1.6 | ColumnipNewCfgStaticRouteInterface | read-create | current | The IP interface of this route. The IP address of the specified interface shall be use as source IP when performs routing. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.4 | ScalaripStaticRouteClearAllByDestIp | read-write | current | Clears all static routes with the specified destination IP address. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.5 | ScalaripStaticRouteClearAllByGatewayIp | read-write | current | Clears all static routes with the specified gateway IP address. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.6 | ScalaripStaticRouteClearAllByInterface | read-write | current | Clears all routes on the specified inteface number. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.7 | ScalaripStaticRouteClearAll | read-write | current | When set to clear(2),clears all static routes. Otherwhise nothing is done. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.8 | ScalaripStaticRouteCurPingInterval | read-only | current | The time between ping retries. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.9 | ScalaripStaticRouteNewPingInterval | read-write | current | The time between ping retries. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.10 | ScalaripStaticRouteCurPingRetries | read-only | current | The number of ping retries. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.11 | ScalaripStaticRouteNewPingRetries | read-write | current | The number of ping retries. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.12 | ScalaripStaticRouteCurEcmpHash | read-only | current | Ecmp Hash based on dipsip/sip. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.13 | ScalaripStaticRouteNewEcmpHash | read-write | current | Ecmp Hash based on dipsip/sip. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.16 | ScalaripStaticRouteCurHealthcheck | read-only | current | Gateway healthcheck functionality |
| 1.3.6.1.4.1.26543.2.7.7.3.1.3.17 | ScalaripStaticRouteNewHealthcheck | read-write | current | Gateway healthcheck functionality |
| 1.3.6.1.4.1.26543.2.7.7.3.1.4 | NodeipForwardCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.4.1 | NodeipFwdGeneralCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.4.1.1 | ScalaripFwdCurCfgState | read-only | current | IP forwarding global state. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.4.1.2 | ScalaripFwdNewCfgState | read-write | current | IP forwarding global state. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.4.1.3 | ScalaripFwdCurCfgDirectedBcast | read-only | current | Enable or disable forwarding directed broadcasts. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.4.1.4 | ScalaripFwdNewCfgDirectedBcast | read-write | current | Enable or disable forwarding directed broadcasts. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.4.1.5 | ScalaripFwdCurCfgNoICMPRedirect | read-only | current | Enable or disable no icmp redirects. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.4.1.6 | ScalaripFwdNewCfgNoICMPRedirect | read-write | current | Enable or disable no icmp redirects. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.4.1.7 | ScalaripFwdCurCfgICMP6Redirect | read-only | current | Enable or disable ICMPv6 redirects. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.4.1.8 | ScalaripFwdNewCfgICMP6Redirect | read-write | current | Enable or disable ICMPv6 redirects. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6 | NodevrrpCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.1 | NodevrrpGeneral | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.1.1 | ScalarvrrpCurCfgGenState | read-only | current | Enable or disable VRRP operation globally. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.1.2 | ScalarvrrpNewCfgGenState | read-write | current | Enable or disable VRRP operation globally. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.1.3 | ScalarvrrpCurCfgGenTckVirtRtrInc | read-only | current | The increment of VRRP virtual router priority. The priority is adjusted by tracking the state of other virtual routers. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.1.4 | ScalarvrrpNewCfgGenTckVirtRtrInc | read-write | current | The increment of VRRP virtual router priority. The priority is adjusted by tracking the state of other virtual routers. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.1.5 | ScalarvrrpCurCfgGenTckIpIntfInc | read-only | current | The increment of VRRP virtual router priority. The priority is adjusted by tracking the state of other router interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.1.6 | ScalarvrrpNewCfgGenTckIpIntfInc | read-write | current | The increment of VRRP virtual router priority. The priority is adjusted by tracking the state of other router interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.1.7 | ScalarvrrpCurCfgGenTckVlanPortInc | read-only | current | The increment of VRRP virtual router priority. The priority is adjusted by tracking the port state of ports that belongs to the same virtual LAN as the virtual… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.1.8 | ScalarvrrpNewCfgGenTckVlanPortInc | read-write | current | The increment of VRRP virtual router priority. The priority is adjusted by tracking the port state of ports that belongs to the same virtual LAN as the virtual… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.1.19 | ScalarvrrpCurCfgGenHoldoff | read-only | current | The time for VRRP virtual router to hold before it begins to change state to backup or master state. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.1.20 | ScalarvrrpNewCfgGenHoldoff | read-write | current | The time for VRRP virtual router to hold before it begins to change state to backup or master state. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.2 | ScalarvrrpVirtRtrTableMaxSize | read-only | current | The maximum number of entries in VRRP virtual router table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.3 | TablevrrpCurCfgVirtRtrTable | not-accessible | current | The table of VRRP virtual routers in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.3.1 | RowvrrpCurCfgVirtRtrTableEntry | not-accessible | current | Information about a VRRP virtual router. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.3.1.1 | ColumnvrrpCurCfgVirtRtrIndx | read-only | current | The VRRP virtual router table index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.3.1.2 | ColumnvrrpCurCfgVirtRtrID | read-only | current | The VRRP virtual router identifier. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.3.1.3 | ColumnvrrpCurCfgVirtRtrAddr | read-only | current | The VRRP virtual router IP address. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.3.1.4 | ColumnvrrpCurCfgVirtRtrIfIndex | read-only | current | The IfIndex that the VRRP virtual router is representing. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.3.1.5 | ColumnvrrpCurCfgVirtRtrInterval | read-only | current | The time interval between VRRP advertisements in seconds. When FAST_ADVERTISEMENT is enabled, this object indicates advertisement interval in centi-seconds |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.3.1.6 | ColumnvrrpCurCfgVirtRtrPriority | read-only | current | The priority value to be used by the specified VRRP virtual routers. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.3.1.7 | ColumnvrrpCurCfgVirtRtrPreempt | read-only | current | This is for controlling whether a higher priority Backup VRRP virtual router preempts a low priority Master. enabled(1) - allow preemption disabled(2) - prohib… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.3.1.9 | ColumnvrrpCurCfgVirtRtrTckVirtRtr | read-only | current | Enable or disable tracking other virtual routers for priority adjustment. The priority increment is defined in vrrpCurCfgGenTckVirtRtrInc. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.3.1.10 | ColumnvrrpCurCfgVirtRtrTckIpIntf | read-only | current | Enable or disable tracking other router interfaces for priority adjustment. The priority increment is defined in vrrpCurCfgGenTckIpIntfInc. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.3.1.15 | ColumnvrrpCurCfgVirtRtrTckVlanPort | read-only | current | Enable or disable tracking port state of VLAN ports for priority adjustment. The priority increment is defined in vrrpCurCfgGenTckVlanPortInc. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.3.1.16 | ColumnvrrpCurCfgVirtRtrState | read-only | current | Enable or disable the VRRP virtual router. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.3.1.17 | ColumnvrrpCurCfgVirtRtrFastAdvertisement | read-only | current | This object provides the status of FAST_ADVERTISEMENT. When FAST_ADVERTISEMENT is enabled, - New message type FAST_ADVERTISEMENT(2) will be used in the VRRP ad… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.3.1.18 | ColumnvrrpCurCfgVirtRtrPreDelay | read-only | current | The pre-emptive delay interval in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.4 | TablevrrpNewCfgVirtRtrTable | not-accessible | current | The table of VRRP virtual routers in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.4.1 | RowvrrpNewCfgVirtRtrTableEntry | not-accessible | current | Information about a VRRP virtual router. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.4.1.1 | ColumnvrrpNewCfgVirtRtrIndx | read-only | current | The VRRP virtual router table index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.4.1.2 | ColumnvrrpNewCfgVirtRtrID | read-create | current | The VRRP virtual router identifier. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.4.1.3 | ColumnvrrpNewCfgVirtRtrAddr | read-create | current | The VRRP virtual router IP address. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.4.1.4 | ColumnvrrpNewCfgVirtRtrIfIndex | read-create | current | The IfIndex that the VRRP virtual router is representing. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.4.1.5 | ColumnvrrpNewCfgVirtRtrInterval | read-create | current | The time interval between VRRP advertisements in seconds. When FAST_ADVERTISEMENT is enabled, this object indicates advertisement interval in centi-seconds |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.4.1.6 | ColumnvrrpNewCfgVirtRtrPriority | read-create | current | The priority value to be used by the specified VRRP virtual router. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.4.1.7 | ColumnvrrpNewCfgVirtRtrPreempt | read-create | current | This is for controlling whether a higher priority Backup VRRP virtual router preempts a low priority Master. enabled(1) - allow preemption disabled(2) - prohib… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.4.1.8 | ColumnvrrpNewCfgVirtRtrDelete | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than delete(2) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.4.1.10 | ColumnvrrpNewCfgVirtRtrTckVirtRtr | read-create | current | Enable or disable tracking other virtual routers for priority adjustment. the priority increment is defined in vrrpNewCfgGenTckVirtRtrInc. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.4.1.11 | ColumnvrrpNewCfgVirtRtrTckIpIntf | read-create | current | Enable or disable tracking other router interfaces for priority adjustment. the priority increment is defined in vrrpNewCfgGenTckIpIntfInc. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.4.1.12 | ColumnvrrpNewCfgVirtRtrTckVlanPort | read-create | current | Enable or disable tracking port state of VLAN ports for priority adjustment. the priority increment is defined in vrrpNewCfgGenTckVlanPortInc. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.4.1.17 | ColumnvrrpNewCfgVirtRtrState | read-create | current | Enable or disable the VRRP virtual router. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.4.1.18 | ColumnvrrpNewCfgVirtRtrFastAdvertisement | read-create | current | This object can be enabled if sub-second advertisement interval is required. When FAST_ADVERTISEMENT is enabled, - New message type FAST_ADVERTISEMENT(2) will … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.4.1.19 | ColumnvrrpNewCfgVirtRtrPreDelay | read-create | current | The pre-emptive delay interval in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.5 | ScalarvrrpIfTableMaxSize | read-only | current | The maximum number of entries in VRRP interface table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.6 | TablevrrpCurCfgIfTable | not-accessible | current | The table of VRRP interface in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.6.1 | RowvrrpCurCfgIfTableEntry | not-accessible | current | Information about a VRRP interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.6.1.1 | ColumnvrrpCurCfgIfIndx | read-only | current | The VRRP interface index. This is eqivalent to IfIndex. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.6.1.2 | ColumnvrrpCurCfgIfAuthType | read-only | current | Type of authentication being used. none(1) - no authentication simple-text-password(2) - use password specified in vrrpCurCfgIfPasswd for authentication. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.6.1.3 | ColumnvrrpCurCfgIfPasswd | read-only | current | The password for authentication. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.7 | TablevrrpNewCfgIfTable | not-accessible | current | The table of VRRP interface in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.7.1 | RowvrrpNewCfgIfTableEntry | not-accessible | current | Information about a VRRP interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.7.1.1 | ColumnvrrpNewCfgIfIndx | read-only | current | The VRRP interface index. This is eqivalent to IfIndex. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.7.1.2 | ColumnvrrpNewCfgIfAuthType | read-create | current | Type of authentication being used. none(1) - no authentication simple-text-password(2) - use password specified in vrrpNewCfgIfPasswd for authentication. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.7.1.3 | ColumnvrrpNewCfgIfPasswd | read-create | current | The password for authentication. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.7.1.4 | ColumnvrrpNewCfgIfDelete | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than delete(2) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.8 | ScalarvrrpVirtRtrGrpTableMaxSize | read-only | current | The maximum number of entries in VRRP Group table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.9 | TablevrrpCurCfgVirtRtrGrpTable | not-accessible | current | The table of VRRP virtual router group in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.9.1 | RowvrrpCurCfgVirtRtrGrpTableEntry | not-accessible | current | Information about a VRRP failover virtual router. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.9.1.1 | ColumnvrrpCurCfgVirtRtrGrpIndx | read-only | current | The VRRP virtual router table index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.9.1.2 | ColumnvrrpCurCfgVirtRtrGrpID | read-only | current | The VRRP virtual router identifier. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.9.1.3 | ColumnvrrpCurCfgVirtRtrGrpIfIndex | read-only | current | The IfIndex that the VRRP virtual router is representing. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.9.1.4 | ColumnvrrpCurCfgVirtRtrGrpInterval | read-only | current | The time interval between VRRP advertisements in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.9.1.5 | ColumnvrrpCurCfgVirtRtrGrpPriority | read-only | current | The priority value to be used by the specified VRRP virtual routers. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.9.1.6 | ColumnvrrpCurCfgVirtRtrGrpPreempt | read-only | current | This is for controlling whether a higher priority Backup VRRP virtual router preempts a low priority Master. enabled(1) - allow preemption disabled(2) - prohib… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.9.1.7 | ColumnvrrpCurCfgVirtRtrGrpState | read-only | current | Enable or disable the VRRP virtual router. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.9.1.10 | ColumnvrrpCurCfgVirtRtrGrpTckIpIntf | read-only | current | Enable or disable tracking other router interfaces for priority adjustment. the priority increment is defined in vrrpCurCfgGenTckIpIntfInc. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.9.1.11 | ColumnvrrpCurCfgVirtRtrGrpTckVlanPort | read-only | current | Enable or disable tracking port state of VLAN ports for priority adjustment. the priority increment is defined in vrrpCurCfgGenTckVlanPortInc. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.9.1.16 | ColumnvrrpCurCfgVirtRtrGrpFastAdvertisement | read-only | current | This object provides the status of FAST_ADVERTISEMENT. When FAST_ADVERTISEMENT is enabled, - New message type FAST_ADVERTISEMENT(2) will be used in the VRRP ad… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.9.1.21 | ColumnvrrpCurCfgVirtRtrGrpPredelay | read-only | current | The pre-emptive delay interval in seconds for specified VRRP virtual routers. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.10 | TablevrrpNewCfgVirtRtrGrpTable | not-accessible | current | The table of VRRP virtual router group in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.10.1 | RowvrrpNewCfgVirtRtrGrpTableEntry | not-accessible | current | Information about a VRRP failover virtual router. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.10.1.1 | ColumnvrrpNewCfgVirtRtrGrpIndx | read-only | current | The VRRP virtual router table index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.10.1.2 | ColumnvrrpNewCfgVirtRtrGrpID | read-create | current | The VRRP virtual router identifier. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.10.1.3 | ColumnvrrpNewCfgVirtRtrGrpIfIndex | read-create | current | The IfIndex that the VRRP virtual router is representing. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.10.1.4 | ColumnvrrpNewCfgVirtRtrGrpInterval | read-create | current | The time interval between VRRP advertisements in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.10.1.5 | ColumnvrrpNewCfgVirtRtrGrpPriority | read-create | current | The priority value to be used by the specified VRRP virtual router. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.10.1.6 | ColumnvrrpNewCfgVirtRtrGrpPreempt | read-create | current | This is for controlling whether a higher priority Backup VRRP virtual router preempts a low priority Master. enabled(1) - allow preemption disabled(2) - prohib… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.10.1.7 | ColumnvrrpNewCfgVirtRtrGrpState | read-create | current | Enable or disable the VRRP virtual router. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.10.1.8 | ColumnvrrpNewCfgVirtRtrGrpDelete | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than delete(2) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.10.1.11 | ColumnvrrpNewCfgVirtRtrGrpTckIpIntf | read-create | current | Enable or disable tracking other router interfaces for priority adjustment. the priority increment is defined in vrrpNewCfgGenTckIpIntfInc. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.10.1.12 | ColumnvrrpNewCfgVirtRtrGrpTckVlanPort | read-create | current | Enable or disable tracking port state of VLAN ports for priority adjustment. the priority increment is defined in vrrpNewCfgGenTckVlanPortInc. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.10.1.17 | ColumnvrrpNewCfgVirtRtrGrpFastAdvertisement | read-create | current | This object can be enabled if sub-second advertisement interval is required. When FAST_ADVERTISEMENT is enabled, - New message type FAST_ADVERTISEMENT(2) will … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.6.10.1.21 | ColumnvrrpNewCfgVirtRtrGrpPredelay | read-create | current | The pre-emptive delay interval in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.7 | NodearpCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.7.1 | ScalararpCurCfgReARPPeriod | read-only | current | Re-ARP Period in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.7.2 | ScalararpNewCfgReARPPeriod | read-write | current | Re-ARP Period in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8 | NodeipBootpCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.1 | ScalaripCurCfgBootpAddr | read-only | current | The IP address of BOOTP server. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.2 | ScalaripNewCfgBootpAddr | read-write | current | The IP address of BOOTP server. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.3 | ScalaripCurCfgBootpAddr2 | read-only | current | The IP address of second BOOTP server. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.4 | ScalaripNewCfgBootpAddr2 | read-write | current | The IP address of second BOOTP server. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.5 | ScalaripCurCfgBootpState | read-only | current | The state of BOOTP relay. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.6 | ScalaripNewCfgBootpState | read-write | current | The state of BOOTP relay. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.20 | TableipCurCfgBootpGlobalServerTable | not-accessible | current | The table of global BOOTP server addresses |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.20.1 | RowipCurCfgBootpGlobalServerEntry | not-accessible | current | A row in the ipCurCfgBootpGlobalServerAddrTable |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.20.1.1 | ColumnipCurCfgBootpGlobalServerIndex | read-only | current | The index of ipCurCfgBootpGlobalServerTable |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.20.1.2 | ColumnipCurCfgBootpGlobalServerAddress | read-only | current | The current global server IP. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.21 | TableipNewCfgBootpGlobalServerTable | not-accessible | current | The table of global BOOTP server addresses |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.21.1 | RowipNewCfgBootpGlobalServerEntry | not-accessible | current | A row in the ipNewCfgBootpGlobalServerAddrTable |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.21.1.1 | ColumnipNewCfgBootpGlobalServerIndex | read-only | current | The index of ipCurCfgBootpGlobalServerTable |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.21.1.2 | ColumnipNewCfgBootpGlobalServerAddress | read-write | current | The current global server IP. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.22 | TableipCurCfgBootpBcastDomainTable | not-accessible | current | The table of broadcast domain settings |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.22.1 | RowipCurCfgBootpBcastDomainEntry | not-accessible | current | A row in the broadcast domain table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.22.1.1 | ColumnipCurCfgBootpBcastDomainIndex | read-only | current | The index of the broadcast domain entry |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.22.1.2 | ColumnipCurCfgBootpBcastDomainVlan | read-only | current | The VLAN of the broadcast domain entry |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.22.1.3 | ColumnipCurCfgBootpBcastDomainEnable | read-only | current | The state of the broadcast domain entry |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.23 | TableipNewCfgBootpBcastDomainTable | not-accessible | current | The table of broadcast domain settings |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.23.1 | RowipNewCfgBootpBcastDomainEntry | not-accessible | current | A row in the broadcast domain table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.23.1.1 | ColumnipNewCfgBootpBcastDomainIndex | read-only | current | The index of the broadcast domain entry |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.23.1.2 | ColumnipNewCfgBootpBcastDomainVlan | read-write | current | The VLAN of the broadcast domain entry |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.23.1.3 | ColumnipNewCfgBootpBcastDomainEnable | read-write | current | The state of the broadcast domain entry |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.23.1.4 | ColumnipNewCfgBootpBcastDomainAction | read-create | current | When set to the value of 2 (delete), the broadcast domain is deleted. When read, other is returned. Setting the value to anything other than 2(delete) has no e… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.24 | TableipCurCfgBootpBcastDomainServerTable | not-accessible | current | The table of broadcast domain servers |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.24.1 | RowipCurCfgBootpBcastDomainServerEntry | not-accessible | current | A row in the broadcast domain server table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.24.1.1 | ColumnipCurCfgBootpBcastDomainBDIndex | read-only | current | The index of the broadcast domain entry in the server table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.24.1.2 | ColumnipCurCfgBootpBcastDomainServIndex | read-only | current | The index of the server in the server table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.24.1.3 | ColumnipCurCfgBootpBcastDomainServerIP | read-only | current | The current broadcast domain server IP. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.25 | TableipNewCfgBootpBcastDomainServerTable | not-accessible | current | The table of broadcast domain servers |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.25.1 | RowipNewCfgBootpBcastDomainServerEntry | not-accessible | current | A row in the broadcast domain server table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.25.1.1 | ColumnipNewCfgBootpBcastDomainBDIndex | read-only | current | The index of the broadcast domain entry in the server table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.25.1.2 | ColumnipNewCfgBootpBcastDomainServIndex | read-only | current | The index of the server in the server table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.25.1.3 | ColumnipNewCfgBootpBcastDomainServerIP | read-write | current | The current broadcast domain server IP. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.26 | ScalaripCurCfgBootpOpt82State | read-only | current | The state of Bootp relay option 82 |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.27 | ScalaripNewCfgBootpOpt82State | read-write | current | Set the stare of Bootp relay option 82 |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.28 | ScalaripCurCfgBootpOpt82Policy | read-only | current | The policy of Bootp relay option 82 |
| 1.3.6.1.4.1.26543.2.7.7.3.1.8.29 | ScalaripNewCfgBootpOpt82Policy | read-write | current | Set the policy of Bootp relay option 82 |
| 1.3.6.1.4.1.26543.2.7.7.3.1.9 | NodednsCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.9.1 | ScalardnsCurCfgPrimaryIpAddr | read-only | current | The DNS primary IP address in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.9.2 | ScalardnsNewCfgPrimaryIpAddr | read-write | current | The DNS primary IP address in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.9.3 | ScalardnsCurCfgSecondaryIpAddr | read-only | current | The DNS primary IP address in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.9.4 | ScalardnsNewCfgSecondaryIpAddr | read-write | current | The DNS primary IP address in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.9.5 | ScalardnsCurCfgDomainName | read-only | current | The DNS doamin name in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.9.6 | ScalardnsNewCfgDomainName | read-write | current | The DNS doamin name in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.9.9 | ScalardnsNewCfgFirstRequestAddr | read-write | current | Type of the first request to dns |
| 1.3.6.1.4.1.26543.2.7.7.3.1.9.10 | ScalardnsCurCfgFirstRequestAddr | read-only | current | Type of the first request to dns |
| 1.3.6.1.4.1.26543.2.7.7.3.1.10 | NodeipNwfCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.10.1 | ScalaripNwfTableMax | read-only | current | The maximum number of rows in the IP network filter table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.10.2 | TableipCurCfgNwfTable | not-accessible | current | The table of IP network filter in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.10.2.1 | RowipCurCfgNwfEntry | not-accessible | current | Information about an IP network filter. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.10.2.1.1 | ColumnipCurCfgNwfIndex | read-only | current | The netowrk filter number for which the NWF is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.10.2.1.2 | ColumnipCurCfgNwfAddr | read-only | current | The IP address of the network filter. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.10.2.1.3 | ColumnipCurCfgNwfMask | read-only | current | The IP network filter mask. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.10.2.1.4 | ColumnipCurCfgNwfState | read-only | current | Enable or disable the network filter. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.10.3 | TableipNewCfgNwfTable | not-accessible | current | The table of IP network filter in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.10.3.1 | RowipNewCfgNwfEntry | not-accessible | current | Information about an IP network filter. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.10.3.1.1 | ColumnipNewCfgNwfIndex | read-only | current | The netowrk filter number for which the NWF is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.10.3.1.2 | ColumnipNewCfgNwfAddr | read-create | current | The IP address of the network filter. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.10.3.1.3 | ColumnipNewCfgNwfMask | read-create | current | The IP network filter mask. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.10.3.1.4 | ColumnipNewCfgNwfState | read-create | current | Enable or disable the network filter. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.10.3.1.5 | ColumnipNewCfgNwfDelete | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11 | NodeipRmapCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.1 | ScalaripRmapTableMax | read-only | current | The maximum number of rows in the IP route map table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.2 | TableipCurCfgRmapTable | not-accessible | current | The table of IP route map in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.2.1 | RowipCurCfgRmapEntry | not-accessible | current | Information about an IP route map. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.2.1.1 | ColumnipCurCfgRmapIndex | read-only | current | The route map number for which the RMAP is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.2.1.2 | ColumnipCurCfgRmapLp | read-only | current | The local-preference of the route map. 4294967295 means none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.2.1.3 | ColumnipCurCfgRmapMetric | read-only | current | The metric of the route map. 4294967295 means none. Range is [1-16777214] if OSPF metric-type is used. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.2.1.4 | ColumnipCurCfgRmapPrec | read-only | current | The precedence of the route map. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.2.1.5 | ColumnipCurCfgRmapWeight | read-only | current | The weight of the route map. 65535 means none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.2.1.6 | ColumnipCurCfgRmapState | read-only | current | Enable or disable the route map. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.2.1.7 | ColumnipCurCfgRmapAp | read-only | current | The as-path prepend of the matched route. Up to 32 AS number can be displayed for the string. The usuage is:<AS number> [<AS number>][ <AS number>] ... |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.2.1.8 | ColumnipCurCfgRmapMetricType | read-only | current | The OSPF metric-type of the matched route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.2.1.9 | ColumnipCurCfgRmapNexthop | read-only | current | Peer address as nexthop of the matched route(only for BGP). |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.3 | TableipNewCfgRmapTable | not-accessible | current | The table of IP route map in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.3.1 | RowipNewCfgRmapEntry | not-accessible | current | Information about an IP route map. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.3.1.1 | ColumnipNewCfgRmapIndex | read-only | current | The route map number for which the RMAP is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.3.1.2 | ColumnipNewCfgRmapLp | read-create | current | The local-preference of the route map. 4294967295 means none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.3.1.3 | ColumnipNewCfgRmapMetric | read-create | current | The metric of the route map. 4294967295 means none. Range is [1-16777214] if OSPF metric-type is used. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.3.1.4 | ColumnipNewCfgRmapPrec | read-create | current | The precedence of the route map. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.3.1.5 | ColumnipNewCfgRmapWeight | read-create | current | The weight of the route map. 65535 means none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.3.1.6 | ColumnipNewCfgRmapState | read-create | current | Enable or disable the route map. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.3.1.7 | ColumnipNewCfgRmapAp | read-create | current | The as-path prepend of the matched route. Up to 32 AS number can be displayed for the string. The usuage is:<AS number> [<AS number>][ <AS number>] ... |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.3.1.8 | ColumnipNewCfgRmapMetricType | read-create | current | The OSPF metric-type of the matched route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.3.1.9 | ColumnipNewCfgRmapDelete | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.3.1.10 | ColumnipNewCfgRmapNexthop | read-create | current | Peer address as nexthop of the matched route(only for BGP). |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.4 | ScalaripAlistTableMax | read-only | current | The maximum number of rows in the IP route map table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.5 | TableipCurCfgAlistTable | not-accessible | current | The table of IP route map access list in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.5.1 | RowipCurCfgAlistEntry | not-accessible | current | Information about an IP route map. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.5.1.1 | ColumnipCurCfgAlistRmapIndex | read-only | current | The route map number for which the RMAP is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.5.1.2 | ColumnipCurCfgAlistIndex | read-only | current | The access list number for which the access list is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.5.1.3 | ColumnipCurCfgAlistNwf | read-only | current | The network filter number of the route map access list. 0 means none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.5.1.4 | ColumnipCurCfgAlistMetric | read-only | current | The metric of the route map access list. 4294967295 means none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.5.1.5 | ColumnipCurCfgAlistAction | read-only | current | Action of the route map access list. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.5.1.6 | ColumnipCurCfgAlistState | read-only | current | Enable or disable the route map access list. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.6 | TableipNewCfgAlistTable | not-accessible | current | The table of IP route map access list in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.6.1 | RowipNewCfgAlistEntry | not-accessible | current | Information about an IP route map. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.6.1.1 | ColumnipNewCfgAlistRmapIndex | read-only | current | The route map number for which the RMAP is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.6.1.2 | ColumnipNewCfgAlistIndex | read-only | current | The access list number for which the access list is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.6.1.3 | ColumnipNewCfgAlistNwf | read-create | current | The network filter number of the route map access list. 0 means none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.6.1.4 | ColumnipNewCfgAlistMetric | read-create | current | The metric of the route map access list. 4294967295 means none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.6.1.5 | ColumnipNewCfgAlistAction | read-create | current | Action of the route map access list. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.6.1.6 | ColumnipNewCfgAlistState | read-create | current | Enable or disable the route map access list. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.6.1.7 | ColumnipNewCfgAlistDelete | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.7 | ScalaripAspathTableMax | read-only | current | The maximum number of rows in the IP route map table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.8 | TableipCurCfgAspathTable | not-accessible | current | The table of IP route map access path configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.8.1 | RowipCurCfgAspathEntry | not-accessible | current | Information about an IP route map. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.8.1.1 | ColumnipCurCfgAspathRmapIndex | read-only | current | The route map number for which the RMAP is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.8.1.2 | ColumnipCurCfgAspathIndex | read-only | current | The access path number for which the access list is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.8.1.3 | ColumnipCurCfgAspathAS | read-only | current | The AS number of the route map access path. 0 means none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.8.1.4 | ColumnipCurCfgAspathAction | read-only | current | Action of the route map access path. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.8.1.5 | ColumnipCurCfgAspathState | read-only | current | Enable or disable the route map access path. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.9 | TableipNewCfgAspathTable | not-accessible | current | The table of IP route map access path configuration |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.9.1 | RowipNewCfgAspathEntry | not-accessible | current | Information about an IP route map. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.9.1.1 | ColumnipNewCfgAspathRmapIndex | read-only | current | The route map number for which the RMAP is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.9.1.2 | ColumnipNewCfgAspathIndex | read-only | current | The access path number for which the access list is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.9.1.3 | ColumnipNewCfgAspathAS | read-create | current | The AS number of the route map access path. 0 means none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.9.1.4 | ColumnipNewCfgAspathAction | read-create | current | Action of the route map access path. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.9.1.5 | ColumnipNewCfgAspathState | read-create | current | Enable or disable the route map access path. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.11.9.1.6 | ColumnipNewCfgAspathDelete | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12 | NodebgpCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.1 | NodebgpGeneral | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.1.1 | ScalarbgpCurCfgState | read-only | current | BGP global state. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.1.2 | ScalarbgpNewCfgState | read-write | current | Globally turn BGP on or off. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.1.3 | ScalarbgpCurCfgLocalPref | read-only | current | Local preference value. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.1.4 | ScalarbgpNewCfgLocalPref | read-write | current | Local Preference value. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.1.5 | ScalarbgpCurCfgASNumber | read-only | current | The autonomous system (AS) number. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.1.6 | ScalarbgpNewCfgASNumber | read-write | current | The autonomous system (AS) number. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.1.7 | ScalarbgpCurCfgEbgpMaxPaths | read-only | current | Maximum eBGP Paths. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.1.8 | ScalarbgpNewCfgEbgpMaxPaths | read-write | current | Maximum eBGP Paths. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.1.9 | ScalarbgpCurCfgIbgpMaxPaths | read-only | current | Maximum iBGP Paths. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.1.10 | ScalarbgpNewCfgIbgpMaxPaths | read-write | current | Maximum iBGP Paths. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.1.11 | ScalarbgpCurCfgAsn4Comp | read-only | current | ASN4 to ASN2 compatibility. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.1.12 | ScalarbgpNewCfgAsn4Comp | read-write | current | ASN4 to ASN2 compatibility. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.1.13 | ScalarbgpCurCfgDscp | read-only | current | BGP dscp marking value. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.1.14 | ScalarbgpNewCfgDscp | read-write | current | BGP dscp marking value. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.1.15 | ScalarbgpNewCfgClusterId | read-write | current | Cluster ID. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.1.16 | ScalarbgpCurCfgClusterId | read-only | current | Cluster ID. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.1.17 | ScalarbgpNewCfgClientToClientReflection | read-write | current | Enable/disable client to client route reflection |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.1.18 | ScalarbgpCurCfgClientToClientReflection | read-only | current | Enable/disable client to client route reflection |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.2 | ScalarbgpPeerTableMax | read-only | current | The maximum number of rows in the BGP peer table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3 | TablebgpCurCfgPeerTable | not-accessible | current | The table of BGP peer in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1 | RowbgpCurCfgPeerEntry | not-accessible | current | Information about a BGP peer. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.1 | ColumnbgpCurCfgPeerIndex | read-only | current | The BGP peer number for which the BGP peer table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.2 | ColumnbgpCurCfgPeerRemoteAddr | read-only | current | The remote IP address of the BGP peer. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.3 | ColumnbgpCurCfgPeerRemoteAs | read-only | current | The remote AS number of the BGP peer. 0 means none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.4 | ColumnbgpCurCfgPeerTtl | read-only | current | The time-to-live value of the BGP peer IP datagram. 0 means none. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.5 | ColumnbgpCurCfgPeerState | read-only | current | Enable or disable the peer. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.10 | ColumnbgpCurCfgPeerMetric | read-only | current | The metric value of the BGP peer. A value of '0' means none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.11 | ColumnbgpCurCfgPeerDefaultAction | read-only | current | The value of default route action. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.12 | ColumnbgpCurCfgPeerOspfState | read-only | current | Enable or disable advertising OSPF routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.13 | ColumnbgpCurCfgPeerFixedState | read-only | current | Enable or disable advertising fixed routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.14 | ColumnbgpCurCfgPeerStaticState | read-only | current | Enable or disable advertising static routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.16 | ColumnbgpCurCfgPeerInRmapList | read-only | current | The route maps present in the in route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx .… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.17 | ColumnbgpCurCfgPeerOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.18 | ColumnbgpCurCfgPeerHold | read-only | current | The hold time |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.19 | ColumnbgpCurCfgPeerAlive | read-only | current | The keep alive time |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.20 | ColumnbgpCurCfgPeerAdvert | read-only | current | The min time between advertisements |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.21 | ColumnbgpCurCfgPeerRetry | read-only | current | The connect retry interval |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.22 | ColumnbgpCurCfgPeerOrig | read-only | current | The min time between route originations |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.23 | ColumnbgpCurCfgPeerRipState | read-only | current | Enable/disable advertising RIP routes |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.24 | ColumnbgpCurCfgPeerPassword | read-only | current | Peer BGP password |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.25 | ColumnbgpCurCfgPeerPassive | read-only | current | Enable/disable BGP passive peer |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.30 | ColumnbgpCurCfgPeerUpdateSrcIf | read-only | current | BGP peer update source interface index |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.31 | ColumnbgpCurCfgPeerUpdateSrcLoopIf | read-only | current | BGP peer update source loopback interface index |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.32 | ColumnbgpCurCfgPeerTtlSecHops | read-only | current | The BGP ttl security hops. 0 means none. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.33 | ColumnbgpCurCfgPeerNexthopSelf | read-only | current | Enable/Disable using this router as next-hop in BGP updates. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.3.1.34 | ColumnbgpCurCfgPeerClient | read-only | current | Enable/disable BGP client peer |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4 | TablebgpNewCfgPeerTable | not-accessible | current | The table of BGP peer in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1 | RowbgpNewCfgPeerEntry | not-accessible | current | Information about a BGP peer. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.1 | ColumnbgpNewCfgPeerIndex | read-only | current | The BGP peer number for which the BGP peer table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.2 | ColumnbgpNewCfgPeerRemoteAddr | read-create | current | The remote IP address of the BGP peer. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.3 | ColumnbgpNewCfgPeerRemoteAs | read-create | current | The remote AS number of the BGP peer. 0 means none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.4 | ColumnbgpNewCfgPeerTtl | read-create | current | The time-to-live value of the BGP peer IP datagram. 0 means none. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.5 | ColumnbgpNewCfgPeerState | read-create | current | Enable or disable the peer. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.6 | ColumnbgpNewCfgPeerDelete | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.10 | ColumnbgpNewCfgPeerMetric | read-create | current | The metric value of the BGP peer. A value of '0' means none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.11 | ColumnbgpNewCfgPeerDefaultAction | read-create | current | The value of default route action. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.12 | ColumnbgpNewCfgPeerOspfState | read-create | current | Enable or disable advertising OSPF routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.13 | ColumnbgpNewCfgPeerFixedState | read-create | current | Enable or disable advertising fixed routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.14 | ColumnbgpNewCfgPeerStaticState | read-create | current | Enable or disable advertising static routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.16 | ColumnbgpNewCfgPeerInRmapList | read-only | current | The route maps present in the in route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx .… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.17 | ColumnbgpNewCfgPeerOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.18 | ColumnbgpNewCfgPeerAddInRmap | read-create | current | The route map to be add into in-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.19 | ColumnbgpNewCfgPeerAddOutRmap | read-create | current | The route map to be add into out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.20 | ColumnbgpNewCfgPeerRemoveInRmap | read-create | current | The route map to be removed from out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.21 | ColumnbgpNewCfgPeerRemoveOutRmap | read-create | current | The route map to be removed from out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.22 | ColumnbgpNewCfgPeerHold | read-create | current | The hold time |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.23 | ColumnbgpNewCfgPeerAlive | read-create | current | The keep alive time |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.24 | ColumnbgpNewCfgPeerAdvert | read-create | current | The min time between advertisements |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.25 | ColumnbgpNewCfgPeerRetry | read-create | current | The connect retry interval |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.26 | ColumnbgpNewCfgPeerOrig | read-create | current | The min time between route originations |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.27 | ColumnbgpNewCfgPeerRipState | read-create | current | Enable/disable advertising RIP routes |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.28 | ColumnbgpNewCfgPeerPassword | read-create | current | Peer BGP password |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.29 | ColumnbgpNewCfgPeerPassive | read-create | current | Enable/disable BGP passive peer |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.30 | ColumnbgpNewCfgPeerUpdateSrcIf | read-create | current | BGP peer update source interface index |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.31 | ColumnbgpNewCfgPeerUpdateSrcLoopIf | read-create | current | BGP peer update source loopback interface index |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.32 | ColumnbgpNewCfgPeerTtlSecHops | read-create | current | The BGP ttl security hops. 0 means none. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.33 | ColumnbgpNewCfgPeerNexthopSelf | read-create | current | Enable/Disable using this router as next-hop in BGP updates. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.4.1.34 | ColumnbgpNewCfgPeerClient | read-create | current | Enable/disable BGP client peer |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.5 | ScalarbgpAggrTableMax | read-only | current | The maximum number of rows in the BGP aggregation table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.6 | TablebgpCurCfgAggrTable | not-accessible | current | The table of BGP aggregation configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.6.1 | RowbgpCurCfgAggrEntry | not-accessible | current | Information about a BGP aggregation. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.6.1.1 | ColumnbgpCurCfgAggrIndex | read-only | current | The aggregation number for which the BGP aggregation is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.6.1.2 | ColumnbgpCurCfgAggrAddr | read-only | current | The IP address of the BGP aggregation. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.6.1.3 | ColumnbgpCurCfgAggrMask | read-only | current | The subnet mask of the BGP aggregation. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.6.1.4 | ColumnbgpCurCfgAggrState | read-only | current | Enable or disable the BGP aggregation. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.7 | TablebgpNewCfgAggrTable | not-accessible | current | The table of BGP aggregation configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.7.1 | RowbgpNewCfgAggrEntry | not-accessible | current | Information about an BGP aggregation. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.7.1.1 | ColumnbgpNewCfgAggrIndex | read-only | current | The aggregation number for which the BGP aggregation is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.7.1.2 | ColumnbgpNewCfgAggrAddr | read-create | current | The IP address of the BGP aggregation. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.7.1.3 | ColumnbgpNewCfgAggrMask | read-create | current | The subnet mask of the BGP aggregation. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.7.1.4 | ColumnbgpNewCfgAggrState | read-create | current | Enable or disable the BGP aggregation. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.12.7.1.5 | ColumnbgpNewCfgAggrDelete | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13 | NodeospfCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.1 | NodeospfGeneral | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.1.1 | ScalarospfCurCfgDefaultRouteMetric | read-only | current | Specify the metric to be assigned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.1.2 | ScalarospfNewCfgDefaultRouteMetric | read-write | current | Specify the metric to be assigned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.1.3 | ScalarospfCurCfgDefaultRouteMetricType | read-only | current | Specify the AS External metric type to be assigned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.1.4 | ScalarospfNewCfgDefaultRouteMetricType | read-write | current | Specify the AS External metric type to be assigned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.1.5 | ScalarospfIntfTableMaxSize | read-only | current | The maximum number of rows in the OSPF Interface table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.1.6 | ScalarospfAreaTableMaxSize | read-only | current | The maximum number of rows in the OSPF Area table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.1.7 | ScalarospfRangeTableMaxSize | read-only | current | The maximum number of rows in the OSPF Range table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.1.8 | ScalarospfVirtIntfTableMaxSize | read-only | current | The maximum number of rows in the OSPF Virtual Interface table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.1.9 | ScalarospfHostTableMaxSize | read-only | current | The maximum number of rows in the OSPF Host table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.1.10 | ScalarospfCurCfgState | read-only | current | OSPF global state. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.1.11 | ScalarospfNewCfgState | read-write | current | Globally turn OSPF on or off. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.1.12 | ScalarospfCurCfgLSDB | read-only | current | The LSDB limit for external LSA. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.1.13 | ScalarospfNewCfgLSDB | read-write | current | Set the LSDB limit for external LSA. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.2 | TableospfCurCfgAreaTable | not-accessible | current | The table of OSPF area in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.2.1 | RowospfCurCfgAreaEntry | not-accessible | current | Information about a OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.2.1.1 | ColumnospfCurCfgAreaIndex | read-only | current | The OSPF area number for which the OSPF area table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.2.1.2 | ColumnospfCurCfgAreaId | read-only | current | The IP Address of the OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.2.1.3 | ColumnospfCurCfgAreaSpfInterval | read-only | current | The SPF interval for the OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.2.1.4 | ColumnospfCurCfgAreaAuthType | read-only | current | Type of authentication being used. none(1) - no authentication password(2) - use password md5(3) - use MD5 authentication. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.2.1.5 | ColumnospfCurCfgAreaType | read-only | current | Type of Area. transit(0) stub(1) nssa(2) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.2.1.6 | ColumnospfCurCfgAreaMetric | read-only | current | Metric (1-65535) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.2.1.7 | ColumnospfCurCfgAreaStatus | read-only | current | Status disabled(0) enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.3 | TableospfNewCfgAreaTable | not-accessible | current | The table of OSPF area in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.3.1 | RowospfNewCfgAreaEntry | not-accessible | current | Information about a OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.3.1.1 | ColumnospfNewCfgAreaIndex | read-only | current | The OSPF area number for which the OSPF area table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.3.1.2 | ColumnospfNewCfgAreaId | read-create | current | The IP Address of the OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.3.1.3 | ColumnospfNewCfgAreaSpfInterval | read-create | current | The SPF interval for the OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.3.1.4 | ColumnospfNewCfgAreaAuthType | read-create | current | Type of authentication being used. none(1) - no authentication password(2) - use password. md5(3) - use MD5 authentication. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.3.1.5 | ColumnospfNewCfgAreaType | read-write | current | Type of Area. transit(0) stub(1) nssa(2) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.3.1.6 | ColumnospfNewCfgAreaMetric | read-write | current | Metric (1-65535) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.3.1.7 | ColumnospfNewCfgAreaStatus | read-write | current | Status disabled(0) enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.3.1.8 | ColumnospfNewCfgAreaDelete | read-write | current | Delete the area no(0), yes(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4 | NodeospfRouteRedistribution | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.1 | NodeospfRedistributeStatic | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.1.1 | ScalarospfCurCfgStaticMetric | read-only | current | The metric to be assigned to static routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.1.2 | ScalarospfNewCfgStaticMetric | read-write | current | The metric to be assigned to static routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.1.3 | ScalarospfCurCfgStaticMetricType | read-only | current | The AS External metric type for static routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.1.4 | ScalarospfNewCfgStaticMetricType | read-write | current | The AS External metric type for static routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.1.5 | ScalarospfCurCfgStaticOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.1.6 | ScalarospfNewCfgStaticOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.1.7 | ScalarospfNewCfgStaticAddOutRmap | read-write | current | The route map to be add into out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.1.8 | ScalarospfNewCfgStaticRemoveOutRmap | read-write | current | The route map to be removed from out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.2 | NodeospfRedistributeEbgp | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.2.1 | ScalarospfCurCfgEbgpMetric | read-only | current | The export metric to be assigned to External BGP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.2.2 | ScalarospfNewCfgEbgpMetric | read-write | current | The export metric to be assigned to External BGP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.2.3 | ScalarospfCurCfgEbgpMetricType | read-only | current | The AS External metric type for External BGP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.2.4 | ScalarospfNewCfgEbgpMetricType | read-write | current | The AS External metric type for External BGP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.2.5 | ScalarospfCurCfgEbgpOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.2.6 | ScalarospfNewCfgEbgpOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.2.7 | ScalarospfNewCfgEbgpAddOutRmap | read-write | current | The route map to be add into out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.2.8 | ScalarospfNewCfgEbgpRemoveOutRmap | read-write | current | The route map to be removed from out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.3 | NodeospfRedistributeIbgp | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.3.1 | ScalarospfCurCfgIbgpMetric | read-only | current | The export metric for Internal BGP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.3.2 | ScalarospfNewCfgIbgpMetric | read-write | current | The export metric for Internal BGP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.3.3 | ScalarospfCurCfgIbgpMetricType | read-only | current | The AS External metric type for Internal BGP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.3.4 | ScalarospfNewCfgIbgpMetricType | read-write | current | The AS External metric type for Internal BGP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.3.5 | ScalarospfCurCfgIbgpOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.3.6 | ScalarospfNewCfgIbgpOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.3.7 | ScalarospfNewCfgIbgpAddOutRmap | read-write | current | The route map to be add into out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.3.8 | ScalarospfNewCfgIbgpRemoveOutRmap | read-write | current | The route map to be removed from out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.4 | NodeospfRedistributeFixed | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.4.1 | ScalarospfCurCfgFixedMetric | read-only | current | The export metric for fixed routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.4.2 | ScalarospfNewCfgFixedMetric | read-write | current | The export metric for fixed routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.4.3 | ScalarospfCurCfgFixedMetricType | read-only | current | The AS External metric type for fixed routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.4.4 | ScalarospfNewCfgFixedMetricType | read-write | current | The AS External metric type for fixed routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.4.5 | ScalarospfCurCfgFixedOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.4.6 | ScalarospfNewCfgFixedOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.4.7 | ScalarospfNewCfgFixedAddOutRmap | read-write | current | The route map to be add into out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.4.8 | ScalarospfNewCfgFixedRemoveOutRmap | read-write | current | The route map to be removed from out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.5 | NodeospfRedistributeRip | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.5.1 | ScalarospfCurCfgRipMetric | read-only | current | The export metric for RIP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.5.2 | ScalarospfNewCfgRipMetric | read-write | current | The export metric for RIP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.5.3 | ScalarospfCurCfgRipMetricType | read-only | current | The AS External metric type for RIP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.5.4 | ScalarospfNewCfgRipMetricType | read-write | current | The AS External metric type for RIP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.5.5 | ScalarospfCurCfgRipOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.5.6 | ScalarospfNewCfgRipOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.5.7 | ScalarospfNewCfgRipAddOutRmap | read-write | current | The route map to be add into out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.4.5.8 | ScalarospfNewCfgRipRemoveOutRmap | read-write | current | The route map to be removed from out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.5 | TableospfCurCfgMdkeyTable | not-accessible | current | The table of OSPF MD5 keys in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.5.1 | RowospfCurCfgMdkeyEntry | not-accessible | current | Information about an OSPF MD keys table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.5.1.1 | ColumnospfCurCfgMdkeyIndex | read-only | current | The OSPF MD5 Key number for which the OSPF MdKey table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.5.1.2 | ColumnospfCurCfgMdkeyKey | read-only | current | The character string representing the MD5 Key. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.6 | TableospfNewCfgMdkeyTable | not-accessible | current | The table of OSPF MD5 keys in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.6.1 | RowospfNewCfgMdkeyEntry | not-accessible | current | Information about an OSPF MD keys table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.6.1.1 | ColumnospfNewCfgMdkeyIndex | read-only | current | The OSPF MD5 Key number for which the OSPF MdKey table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.6.1.2 | ColumnospfNewCfgMdkeyKey | read-create | current | The character string representing the MD5 Key. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.6.1.3 | ColumnospfNewCfgMdkeyDelete | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.7 | TableospfCurCfgIntfTable | not-accessible | current | The table of OSPF Interface in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.7.1 | RowospfCurCfgIntfEntry | not-accessible | current | Information about an OSPF Interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.7.1.1 | ColumnospfCurCfgIntfIndex | read-only | current | The OSPF Interface number for which the OSPF Interface table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.7.1.2 | ColumnospfCurCfgIntfArea | read-only | current | The index of the area that the interface belongs (0..2) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.7.1.3 | ColumnospfCurCfgIntfMdkey | read-only | current | The MD5 key for the OSPF interface 0 (none) no MD5 authentication. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.7.1.4 | ColumnospfCurCfgIntfCost | read-only | current | Interface cost |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.7.1.5 | ColumnospfCurCfgIntfPrio | read-only | current | Interface router priority |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.7.1.6 | ColumnospfCurCfgIntfHello | read-only | current | Hello interval |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.7.1.7 | ColumnospfCurCfgIntfHelloMS | read-only | current | Units of time measurement for Hello interval seconds(0), milliseconds(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.7.1.8 | ColumnospfCurCfgIntfDead | read-only | current | Dead interval |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.7.1.9 | ColumnospfCurCfgIntfDeadMS | read-only | current | Units of time measurement for Dead interval seconds(0), milliseconds(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.7.1.10 | ColumnospfCurCfgIntfTrans | read-only | current | Transit delay |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.7.1.11 | ColumnospfCurCfgIntfRetra | read-only | current | Retransmit interval |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.7.1.12 | ColumnospfCurCfgIntfAuthKey | read-only | current | Authentication Key |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.7.1.13 | ColumnospfCurCfgIntfPassive | read-only | current | Passive interface disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.7.1.14 | ColumnospfCurCfgIntfStatus | read-only | current | Status of the interface disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.7.1.15 | ColumnospfCurCfgIntfPtop | read-only | current | Point-to-point interface disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.8 | TableospfNewCfgIntfTable | not-accessible | current | The table of OSPF interface in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.8.1 | RowospfNewCfgIntfEntry | not-accessible | current | Information about an OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.8.1.1 | ColumnospfNewCfgIntfIndex | read-only | current | The OSPF Interface number for which the OSPF Interface table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.8.1.2 | ColumnospfNewCfgIntfArea | read-create | current | The index of the area that the interface belongs |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.8.1.3 | ColumnospfNewCfgIntfMdkey | read-create | current | The MD5 key for the OSPF interface 0 (none) no MD5 authentication. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.8.1.4 | ColumnospfNewCfgIntfCost | read-create | current | Interface cost(1..65535) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.8.1.5 | ColumnospfNewCfgIntfPrio | read-create | current | Interface router priority(0..255) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.8.1.6 | ColumnospfNewCfgIntfHello | read-create | current | Hello interval(1..65535s | 50..65535ms) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.8.1.7 | ColumnospfNewCfgIntfHelloMS | read-create | current | Units of time measurement for Hello interval seconds(0), milliseconds(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.8.1.8 | ColumnospfNewCfgIntfDead | read-create | current | Dead interval(1..65535s |1000..65535ms) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.8.1.9 | ColumnospfNewCfgIntfDeadMS | read-create | current | Units of time measurement for Dead interval seconds(0), milliseconds(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.8.1.10 | ColumnospfNewCfgIntfTrans | read-create | current | Transit delay(1..3600) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.8.1.11 | ColumnospfNewCfgIntfRetra | read-create | current | Retransmit interval(1..3600) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.8.1.12 | ColumnospfNewCfgIntfAuthKey | read-create | current | Authentication Key |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.8.1.13 | ColumnospfNewCfgIntfPassive | read-create | current | Passive interface disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.8.1.14 | ColumnospfNewCfgIntfStatus | read-create | current | Status of the interface disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.8.1.15 | ColumnospfNewCfgIntfDelete | read-write | current | Delete the interface other(0), delete(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.8.1.16 | ColumnospfNewCfgIntfPtop | read-create | current | Point-to-point interface disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.9 | TableospfCurCfgVirtIntfTable | not-accessible | current | The table of OSPF Virtual Interface configuration in the current configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.9.1 | RowospfCurCfgVirtIntfEntry | not-accessible | current | Information about an OSPF virtual Interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.9.1.1 | ColumnospfCurCfgVirtIntfIndex | read-only | current | The OSPF Virtual Interface number for which the OSPF Virtual Interface table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.9.1.2 | ColumnospfCurCfgVirtIntfAreaId | read-only | current | The index of the OSPF area to which this virtual interface belongs. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.9.1.3 | ColumnospfCurCfgVirtIntfNbr | read-only | current | The IP Address of the OSPF neighbor for this virtual interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.9.1.4 | ColumnospfCurCfgVirtIntfMdkey | read-only | current | The MD5 key for the OSPF virtual interface 0 (none) no MD5 authentication. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.9.1.5 | ColumnospfCurCfgVirtIntfHello | read-only | current | Hello interval |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.9.1.6 | ColumnospfCurCfgVirtIntfHelloMS | read-only | current | Units of time measurement for Hello interval seconds(0), milliseconds(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.9.1.7 | ColumnospfCurCfgVirtIntfDead | read-only | current | Dead interval |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.9.1.8 | ColumnospfCurCfgVirtIntfDeadMS | read-only | current | Units of time measurement for Dead interval seconds(0), milliseconds(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.9.1.9 | ColumnospfCurCfgVirtIntfTrans | read-only | current | Transit delay |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.9.1.10 | ColumnospfCurCfgVirtIntfRetra | read-only | current | Retransmit interval |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.9.1.11 | ColumnospfCurCfgVirtIntfAuthKey | read-only | current | Authentication Key |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.9.1.12 | ColumnospfCurCfgVirtIntfStatus | read-only | current | Status disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.10 | TableospfNewCfgVirtIntfTable | not-accessible | current | The table of OSPF Virtual interface in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.10.1 | RowospfNewCfgVirtIntfEntry | not-accessible | current | Information about an OSPF virtual interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.10.1.1 | ColumnospfNewCfgVirtIntfIndex | read-only | current | The OSPF Virtual Interface number for which the OSPF Virtual Interface table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.10.1.2 | ColumnospfNewCfgVirtIntfAreaId | read-create | current | The index of the OSPF area to which this virtual interface belongs. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.10.1.3 | ColumnospfNewCfgVirtIntfNbr | read-create | current | The IP Address of the OSPF neighbor for this virtual interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.10.1.4 | ColumnospfNewCfgVirtIntfMdkey | read-create | current | The MD5 key for the OSPF virtual interface 0 (none) no MD5 authentication. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.10.1.5 | ColumnospfNewCfgVirtIntfHello | read-create | current | Hello interval(1..65535s | 50..65535ms) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.10.1.6 | ColumnospfNewCfgVirtIntfHelloMS | read-create | current | Units of time measurement fo Hello interval seconds(0), milliseconds(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.10.1.7 | ColumnospfNewCfgVirtIntfDead | read-create | current | Dead interval(1..65535s | 1000..65535ms) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.10.1.8 | ColumnospfNewCfgVirtIntfDeadMS | read-create | current | Units of time measurement fo Dead interval seconds(0), milliseconds(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.10.1.9 | ColumnospfNewCfgVirtIntfTrans | read-create | current | Transit delay(1..3600) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.10.1.10 | ColumnospfNewCfgVirtIntfRetra | read-create | current | Retransmit interval(1..3600) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.10.1.11 | ColumnospfNewCfgVirtIntfAuthKey | read-create | current | Authentication Key SIZE(0..8) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.10.1.12 | ColumnospfNewCfgVirtIntfStatus | read-create | current | Status disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.10.1.13 | ColumnospfNewCfgVirtIntfDelete | read-write | current | Delete other(0), delete(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.11 | ScalarospfMdkeyTableMaxSize | read-only | current | The maximum number of rows in the OSPF Mdkey table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.12 | TableospfCurCfgHostTable | not-accessible | current | The table of OSPF Host configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.12.1 | RowospfCurCfgHostEntry | not-accessible | current | Information about a OSPF host. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.12.1.1 | ColumnospfCurCfgHostIndex | read-only | current | The OSPF host number for which the OSPF host table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.12.1.2 | ColumnospfCurCfgHostIpAddr | read-only | current | The IP Address of the OSPF host. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.12.1.3 | ColumnospfCurCfgHostAreaIndex | read-only | current | The area index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.12.1.4 | ColumnospfCurCfgHostCost | read-only | current | The cost of the OSPF host. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.12.1.5 | ColumnospfCurCfgHostState | read-only | current | Enable or disable an OSPF Host |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.13 | TableospfNewCfgHostTable | not-accessible | current | The table of OSPF Host configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.13.1 | RowospfNewCfgHostEntry | not-accessible | current | Information about a OSPF host. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.13.1.1 | ColumnospfNewCfgHostIndex | read-only | current | The OSPF host number for which the OSPF host table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.13.1.2 | ColumnospfNewCfgHostIpAddr | read-create | current | The IP Address of the OSPF host. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.13.1.3 | ColumnospfNewCfgHostAreaIndex | read-create | current | The OSPF area index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.13.1.4 | ColumnospfNewCfgHostCost | read-create | current | The cost of the OSPF host. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.13.1.5 | ColumnospfNewCfgHostState | read-create | current | Enable or disable an OSPF Host |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.13.1.6 | ColumnospfNewCfgHostDelete | read-write | current | Delete the OSPF host: no(0), yes(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.14 | TableospfCurCfgRangeTable | not-accessible | current | The table of OSPF summary range in the current configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.14.1 | RowospfCurCfgRangeEntry | not-accessible | current | Information about an OSPF summary range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.14.1.1 | ColumnospfCurCfgRangeIndex | read-only | current | The range number for which the OSPF summary range table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.14.1.2 | ColumnospfCurCfgRangeAddr | read-only | current | The IP Address of the range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.14.1.3 | ColumnospfCurCfgRangeMask | read-only | current | The mask of the range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.14.1.4 | ColumnospfCurCfgRangeAreaIndex | read-only | current | The area index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.14.1.5 | ColumnospfCurCfgRangeHideState | read-only | current | The state of the hide range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.14.1.6 | ColumnospfCurCfgRangeState | read-only | current | The state of the range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.15 | TableospfNewCfgRangeTable | not-accessible | current | The table of OSPF summary range in the new configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.15.1 | RowospfNewCfgRangeEntry | not-accessible | current | Information about an OSPF summary range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.15.1.1 | ColumnospfNewCfgRangeIndex | read-only | current | The range number for which the OSPF summary range table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.15.1.2 | ColumnospfNewCfgRangeAddr | read-create | current | The IP Address of the range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.15.1.3 | ColumnospfNewCfgRangeMask | read-create | current | The mask of the range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.15.1.4 | ColumnospfNewCfgRangeAreaIndex | read-create | current | The area index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.15.1.5 | ColumnospfNewCfgRangeHideState | read-create | current | The state of the hide range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.15.1.6 | ColumnospfNewCfgRangeState | read-create | current | The state of the range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.15.1.7 | ColumnospfNewCfgRangeDelete | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.20 | TableospfCurCfgLoopIfTable | not-accessible | current | The table of OSPF Loopback Interfaces in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.20.1 | RowospfCurCfgLoopIfEntry | not-accessible | current | Information about an OSPF Loopback Interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.20.1.1 | ColumnospfCurCfgLoopIfIndex | read-only | current | The OSPF Loopback Interface number for which the OSPF Interface table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.20.1.2 | ColumnospfCurCfgLoopIfArea | read-only | current | The index of the area that the loopback interface belongs |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.20.1.3 | ColumnospfCurCfgLoopIfStatus | read-only | current | Status of the loopback interface disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.21 | TableospfNewCfgLoopIfTable | not-accessible | current | The table of OSPF loopback interface in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.21.1 | RowospfNewCfgLoopIfEntry | not-accessible | current | Information about an OSPF loopback interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.21.1.1 | ColumnospfNewCfgLoopIfIndex | read-only | current | The OSPF loopback interface number for which the OSPF Loopback Interface table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.21.1.2 | ColumnospfNewCfgLoopIfArea | read-create | current | The index of the area that the loopback interface belongs (0..5) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.21.1.3 | ColumnospfNewCfgLoopIfStatus | read-create | current | Status of the loopback interface disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.13.21.1.4 | ColumnospfNewCfgLoopIfDelete | read-write | current | Delete the loopback interface other(0), delete(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.14 | NodeipGeneralCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.14.1 | ScalaripCurCfgRouterID | read-only | current | The router ID of the switch. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.14.2 | ScalaripNewCfgRouterID | read-write | current | The router ID of the switch. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.15 | NodeipStaticArpCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.15.1 | ScalaripStaticArpTableMaxSize | read-only | current | The maximum number of rows in the Static ARP table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.15.2 | TableipCurCfgStaticArpTable | not-accessible | current | The table of static ARPs in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.15.2.1 | RowipCurCfgStaticArpEntry | not-accessible | current | A row in the static ARP table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.15.2.1.1 | ColumnipCurCfgStaticArpIndx | read-only | current | The index of the static ARP table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.15.2.1.2 | ColumnipCurCfgStaticArpIp | read-only | current | The IP address for the ARP entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.15.2.1.3 | ColumnipCurCfgStaticArpMAC | read-only | current | The MAC address for the ARP entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.15.2.1.4 | ColumnipCurCfgStaticArpVlan | read-only | current | The VLAN for the ARP entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.15.2.1.5 | ColumnipCurCfgStaticArpPortIndex | read-only | current | The port or any of one of the trunk port for the ARP entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.15.3 | TableipNewCfgStaticArpTable | not-accessible | current | The table of static ARPs in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.15.3.1 | RowipNewCfgStaticArpEntry | not-accessible | current | A row in the static ARP table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.15.3.1.1 | ColumnipNewCfgStaticArpIndx | read-only | current | The index of the static ARP table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.15.3.1.2 | ColumnipNewCfgStaticArpIp | read-create | current | The IP address for the ARP entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.15.3.1.3 | ColumnipNewCfgStaticArpMAC | read-create | current | The MAC address for the ARP entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.15.3.1.4 | ColumnipNewCfgStaticArpVlan | read-create | current | The VLAN for the ARP entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.15.3.1.5 | ColumnipNewCfgStaticArpPortIndex | read-create | current | The port or any one of the trunk port for the ARP entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.15.3.1.6 | ColumnipNewCfgStaticArpAction | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other is returned. Setting the value to anything other than 2(delete) has no effect … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.15.4 | ScalaripStaticArpClearAll | read-write | current | When set to clear(2), clears all static ARP entries. Otherwise nothing is done. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18 | Noderip2Cfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.1 | TableripCurCfgIntfTable | not-accessible | current | The table of RIP on IP interface in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.1.1 | RowripCurCfgIntfEntry | not-accessible | current | Information about RIP on IP interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.1.1.1 | ColumnripCurCfgIntfIndex | read-only | current | The interface number for which the RIP information is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.1.1.2 | ColumnripCurCfgIntfVersion | read-only | current | RIP version. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.1.1.3 | ColumnripCurCfgIntfState | read-only | current | Enable or disable RIP protocol. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.1.1.4 | ColumnripCurCfgIntfListen | read-only | current | Enable or disable listening to route updates. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.1.1.6 | ColumnripCurCfgIntfTrigUpdate | read-only | current | Enable or disable triggered updates. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.1.1.7 | ColumnripCurCfgIntfMcastUpdate | read-only | current | Enable or disable multicast updates. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.1.1.8 | ColumnripCurCfgIntfPoisonReverse | read-only | current | RIP poison reverse. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.1.1.9 | ColumnripCurCfgIntfSupply | read-only | current | Enable or disable supplying route updates. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.1.1.10 | ColumnripCurCfgIntfMetric | read-only | current | RIP route metric for this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.1.1.11 | ColumnripCurCfgIntfAuth | read-only | current | The type of Authentication used on this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.1.1.12 | ColumnripCurCfgIntfKey | read-only | current | RIP update authentication password. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.1.1.13 | ColumnripCurCfgIntfDefault | read-only | current | Specifies what RIP does with default routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.1.1.14 | ColumnripCurCfgIntfSplitHorizon | read-only | current | RIP split horizon. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.2 | TableripNewCfgIntfTable | not-accessible | current | The table of RIP on IP interface in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.2.1 | RowripNewCfgIntfEntry | not-accessible | current | Information about RIP on IP interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.2.1.1 | ColumnripNewCfgIntfIndex | read-only | current | The interface number for which the RIP information is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.2.1.2 | ColumnripNewCfgIntfVersion | read-create | current | RIP version. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.2.1.3 | ColumnripNewCfgIntfSupply | read-create | current | Enable or disable supplying route updates. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.2.1.4 | ColumnripNewCfgIntfListen | read-create | current | Enable or disable listening to route updates. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.2.1.6 | ColumnripNewCfgIntfTrigUpdate | read-create | current | Enable or disable triggered updates. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.2.1.7 | ColumnripNewCfgIntfMcastUpdate | read-create | current | Enable or disable multicast updates. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.2.1.8 | ColumnripNewCfgIntfPoisonReverse | read-create | current | RIP poison reverse. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.2.1.9 | ColumnripNewCfgIntfState | read-create | current | Enable or disable RIP protocol. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.2.1.10 | ColumnripNewCfgIntfMetric | read-write | current | RIP route metric for this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.2.1.11 | ColumnripNewCfgIntfAuth | read-write | current | The type of Authentication used on this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.2.1.12 | ColumnripNewCfgIntfKey | read-create | current | RIP update authentication password. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.2.1.13 | ColumnripNewCfgIntfDefault | read-create | current | Specifies what RIP does with default routes. The default routes action could be set to listen/supply/both/none. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.2.1.14 | ColumnripNewCfgIntfSplitHorizon | read-write | current | RIP split horizon. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.3 | NoderipGeneral | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.3.1 | Scalarrip2CurCfgState | read-only | current | RIP global state. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.3.2 | Scalarrip2NewCfgState | read-write | current | Globally turn RIP on or off. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.3.3 | Scalarrip2CurCfgUpdatePeriod | read-only | current | Update Period in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.3.4 | Scalarrip2NewCfgUpdatePeriod | read-write | current | Update Period in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4 | NoderipRouteRedistribution | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.1 | NoderipRedistributeStatic | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.1.1 | ScalarripCurCfgStaticMetric | read-only | current | The metric to be assigned to static routes. A value of 0 indicates none. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.1.2 | ScalarripNewCfgStaticMetric | read-write | current | The metric to be assigned to static routes. A value of 0 indicates none. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.1.5 | ScalarripCurCfgStaticOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.1.6 | ScalarripNewCfgStaticOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.1.7 | ScalarripNewCfgStaticAddOutRmap | read-write | current | The route map to be add into out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.1.8 | ScalarripNewCfgStaticRemoveOutRmap | read-write | current | The route map to be removed from out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.2 | NoderipRedistributeEbgp | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.2.1 | ScalarripCurCfgEbgpMetric | read-only | current | The export metric to be assigned to External BGP routes. A value of 0 indicates none. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.2.2 | ScalarripNewCfgEbgpMetric | read-write | current | The export metric to be assigned to External BGP routes. A value of 0 indicates none. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.2.5 | ScalarripCurCfgEbgpOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.2.6 | ScalarripNewCfgEbgpOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.2.7 | ScalarripNewCfgEbgpAddOutRmap | read-write | current | The route map to be add into out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.2.8 | ScalarripNewCfgEbgpRemoveOutRmap | read-write | current | The route map to be removed from out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.3 | NoderipRedistributeIbgp | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.3.1 | ScalarripCurCfgIbgpMetric | read-only | current | The export metric for Internal BGP routes. A value of 0 indicates none. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.3.2 | ScalarripNewCfgIbgpMetric | read-write | current | The export metric for Internal BGP routes. A value of 0 indicates none. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.3.5 | ScalarripCurCfgIbgpOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.3.6 | ScalarripNewCfgIbgpOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.3.7 | ScalarripNewCfgIbgpAddOutRmap | read-write | current | The route map to be add into out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.3.8 | ScalarripNewCfgIbgpRemoveOutRmap | read-write | current | The route map to be removed from out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.4 | NoderipRedistributeFixed | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.4.1 | ScalarripCurCfgFixedMetric | read-only | current | The export metric for fixed routes. A value of 0 indicates none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.4.2 | ScalarripNewCfgFixedMetric | read-write | current | The export metric for fixed routes. A value of 0 indicates none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.4.5 | ScalarripCurCfgFixedOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.4.6 | ScalarripNewCfgFixedOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.4.7 | ScalarripNewCfgFixedAddOutRmap | read-write | current | The route map to be add into out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.4.8 | ScalarripNewCfgFixedRemoveOutRmap | read-write | current | The route map to be removed from out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.5 | NoderipRedistributeOspf | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.5.1 | ScalarripCurCfgOspfMetric | read-only | current | The export metric for RIP routes. A value of 0 indicates none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.5.2 | ScalarripNewCfgOspfMetric | read-write | current | The export metric for RIP routes. A value of 0 indicates none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.5.5 | ScalarripCurCfgOspfOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.5.6 | ScalarripNewCfgOspfOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.5.7 | ScalarripNewCfgOspfAddOutRmap | read-write | current | The route map to be add into out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.5.8 | ScalarripNewCfgOspfRemoveOutRmap | read-write | current | The route map to be removed from out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.6 | NoderipRedistributeEospf | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.6.1 | ScalarripCurCfgEospfMetric | read-only | current | The export metric for RIP routes. A value of 0 indicates none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.6.2 | ScalarripNewCfgEospfMetric | read-write | current | The export metric for RIP routes. A value of 0 indicates none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.6.5 | ScalarripCurCfgEospfOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.6.6 | ScalarripNewCfgEospfOutRmapList | read-only | current | The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.6.7 | ScalarripNewCfgEospfAddOutRmap | read-write | current | The route map to be add into out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.18.4.6.8 | ScalarripNewCfgEospfRemoveOutRmap | read-write | current | The route map to be removed from out-rmap list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19 | NodeigmpCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.1 | ScalarigmpCurCfgOnOff | read-only | current | Globally turn IGMP On/Off. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.2 | ScalarigmpNewCfgOnOff | read-write | current | Globally turn IGMP On/Off. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.9 | NodeigmpSnoopCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.9.7 | ScalarigmpSnoopCurCfgMrto | read-only | current | The value of multicast router timeout in the current config. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.9.8 | ScalarigmpSnoopNewCfgMrto | read-write | current | The value of multicast router timeout in the new config. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.9.9 | ScalarigmpSnoopCurCfgAggrEnaDis | read-only | current | Enable/Disable of IGMP Report aggregation. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.9.10 | ScalarigmpSnoopNewCfgAggrEnaDis | read-write | current | Enable/Disable of IGMP Report aggregation. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.9.11 | ScalarigmpSnoopCurCfgEnaDis | read-only | current | The current status of IGMP Snooping. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.9.12 | ScalarigmpSnoopNewCfgEnaDis | read-write | current | Set Enable/Disable of IGMP Snooping. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.9.13 | ScalarigmpSnoopNewCfgVlanAdd | read-write | current | The VLAN to be added to snooping vlan list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.9.14 | ScalarigmpSnoopNewCfgVlanRem | read-write | current | The VLAN to be removed from snooping vlan list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.9.15 | ScalarigmpSnoopNewCfgVlanClear | read-write | current | Removing ALL Snooping Vlans. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.9.16 | ScalarigmpSnoopCurCfgVlanBmap | read-only | current | The snooping vlans present in the vlan map list. The snooping vlans are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxx… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.9.17 | ScalarigmpSnoopNewCfgVlanBmap | read-write | current | The snooping vlans present in the vlan map list. The snooping vlans are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxx… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.9.26 | ScalarigmpSnoopCurCfgSrcIp | read-only | current | The source ip for GSQ proxy in current config. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.9.27 | ScalarigmpSnoopNewCfgSrcIp | read-write | current | The source ip for GSQ proxy in new config. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.9.33 | ScalarigmpSnoopSetToDefault | read-write | current | When setting the value setDefault(2), the IGMP Snooping configuration is set to the default values. When reading, none(1) is always returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.10 | NodeigmpStaticMrtrCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.10.1 | TableigmpStaticMrtrCurCfgTable | not-accessible | current | The IGMP Static Multicast Router table in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.10.1.1 | RowigmpStaticMrtrCurCfgTableEntry | not-accessible | current | A row in the Static Multicast Router table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.10.1.1.1 | ColumnigmpStaticMrtrCurCfgIndx | read-only | current | The IGMP Multicast Router table port index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.10.1.1.2 | ColumnigmpStaticMrtrCurCfgPortId | read-only | current | The IGMP Multicast Router port in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.10.1.1.3 | ColumnigmpStaticMrtrCurCfgVlanId | read-only | current | The IGMP Multicast Router port in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.10.1.1.4 | ColumnigmpStaticMrtrCurCfgVersion | read-only | current | The IGMP version of the IGMP Static Multicast Router. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.10.2 | TableigmpStaticMrtrNewCfgTable | not-accessible | current | The IGMP Static Multicast Router table in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.10.2.1 | RowigmpStaticMrtrNewCfgTableEntry | not-accessible | current | A row in the Static Multicast Router table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.10.2.1.1 | ColumnigmpStaticMrtrNewCfgIndx | read-only | current | The IGMP Multicast Router table port index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.10.2.1.2 | ColumnigmpStaticMrtrNewCfgPortId | read-write | current | The IGMP Multicast Router port in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.10.2.1.3 | ColumnigmpStaticMrtrNewCfgVlanId | read-write | current | The IGMP Multicast Router port in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.10.2.1.4 | ColumnigmpStaticMrtrNewCfgVersion | read-write | current | The IGMP version of the IGMP Static Multicast Router. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.10.2.1.5 | ColumnigmpStaticMrtrNewCfgDelete | read-write | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.10.3 | ScalarigmpStaticMrtrNewCfgClear | read-write | current | When set to the value of 2 (clear), the entire table is deleted. When read, other(1) is returned. Setting the value to anything other than 2(clear) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11 | NodeigmpFilterCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.1 | TableigmpFltCurCfgTable | not-accessible | current | The IGMP filtering table in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.1.1 | RowigmpFltCurCfgTableEntry | not-accessible | current | A row in the filtering table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.1.1.1 | ColumnigmpFltCurCfgIndx | read-only | current | The IGMP filter table index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.1.1.2 | ColumnigmpFltCurCfgMcastIp1 | read-only | current | Range1 Multicast IP address to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.1.1.3 | ColumnigmpFltCurCfgMcastIp2 | read-only | current | Range2 Multicast IP address to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.1.1.4 | ColumnigmpFltCurCfgAction | read-only | current | The action for the IGMP filtering rule. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.1.1.5 | ColumnigmpFltCurCfgState | read-only | current | The state of this IGMP filtering rule. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.2 | TableigmpFltNewCfgTable | not-accessible | current | The IGMP filtering table in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.2.1 | RowigmpFltNewCfgTableEntry | not-accessible | current | A row in the filtering table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.2.1.1 | ColumnigmpFltNewCfgIndx | read-only | current | The IGMP filter table index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.2.1.2 | ColumnigmpFltNewCfgMcastIp1 | read-write | current | Range1 Multicast source IP address to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.2.1.3 | ColumnigmpFltNewCfgMcastIp2 | read-write | current | Range2 Multicast source IP address to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.2.1.4 | ColumnigmpFltNewCfgAction | read-write | current | The action for the IGMP filtering rule. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.2.1.5 | ColumnigmpFltNewCfgState | read-write | current | The state of this IGMP filtering rule. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.2.1.6 | ColumnigmpFltNewCfgDelete | read-write | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.3 | TableigmpFltCurCfgPortTable | not-accessible | current | The IGMP filtering port table in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.3.1 | RowigmpFltCurCfgPortTableEntry | not-accessible | current | A row in the IGMP filtering port table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.3.1.1 | ColumnigmpFltCurCfgPortIndx | read-only | current | The port index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.3.1.2 | ColumnigmpFltCurCfgPortState | read-only | current | Enable or disable IGMP filtering. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.3.1.3 | ColumnigmpFltCurCfgPortFiltBmap | read-only | current | The IGMP filtering rules applied to the port. The filtering rules are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx .… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.4 | TableigmpFltNewCfgPortTable | not-accessible | current | The IGMP filtering port table in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.4.1 | RowigmpFltNewCfgPortTableEntry | not-accessible | current | A row in the IGMP filtering port table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.4.1.1 | ColumnigmpFltNewCfgPortIndx | read-only | current | The port index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.4.1.2 | ColumnigmpFltNewCfgPortState | read-write | current | Enable or disable IGMP filtering. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.4.1.3 | ColumnigmpFltNewCfgPortFiltBmap | read-only | current | The IGMP filtering rules applied to the port. The filtering rules are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx .… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.4.1.4 | ColumnigmpFltNewCfgPortAddFiltRule | read-write | current | This is an action object to add filtering rule to a port. The value specified with this object is the index to the fltNewCfgTable for which filtering rule to b… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.4.1.5 | ColumnigmpFltNewCfgPortRemFiltRule | read-write | current | This is an action object to remove filtering rule from a port. The value specified with this object is the index to the fltNewCfgTable for which filtering rule… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.5 | ScalarigmpFltCurCfgEnaDis | read-only | current | Enable/Disable of IGMP Filtering. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.11.6 | ScalarigmpFltNewCfgEnaDis | read-write | current | Enable/Disable of IGMP Filtering. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12 | NodeigmpRelayCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.1 | ScalarigmpRelayCurCfgEnaDis | read-only | current | The current status of IGMP Relay. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.2 | ScalarigmpRelayNewCfgEnaDis | read-write | current | Enable/Disable of IGMP Relay. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.3 | ScalarigmpRelayNewCfgAddVlan | read-write | current | The VLAN to be added to relay vlan list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.4 | ScalarigmpRelayNewCfgRemVlan | read-write | current | The VLAN to be removed from relay vlan list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.5 | ScalarigmpRelayNewCfgClearVlan | read-write | current | Removing ALL Relay Vlans. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.6 | ScalarigmpRelayCurCfgVlanBmap | read-only | current | The relay vlans present in the vlan map list. The relay vlans are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ...… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.7 | ScalarigmpRelayNewCfgVlanBmap | read-write | current | The relay vlans present in the vlan map list. The relay vlans are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ...… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.8 | ScalarigmpRelayCurCfgReport | read-only | current | The Unsolicited Report Interval. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.9 | ScalarigmpRelayNewCfgReport | read-write | current | Set Unsolicited Report Interval. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.10 | TableigmpRelayMrtrCurCfgTable | not-accessible | current | The IGMP relay multicast router table in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.10.1 | RowigmpRelayMrtrCurCfgTableEntry | not-accessible | current | A row in the IGMP relay multicast router table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.10.1.1 | ColumnigmpRelayMrtrCurCfgIndx | read-only | current | The IGMP relay multicast router table index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.10.1.2 | ColumnigmpRelayMrtrCurCfgAddr | read-only | current | The IP address of the multicast router. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.10.1.3 | ColumnigmpRelayMrtrCurCfgEnaDis | read-only | current | The status of the multicast router. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.10.1.4 | ColumnigmpRelayMrtrCurCfgInterval | read-only | current | The interval between ping attempts. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.10.1.5 | ColumnigmpRelayMrtrCurCfgRetry | read-only | current | The number of failed attempts to declare router DOWN. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.10.1.6 | ColumnigmpRelayMrtrCurCfgRestr | read-only | current | The number of successful attempts to declare router UP. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.10.1.7 | ColumnigmpRelayMrtrCurCfgVersion | read-only | current | The IGMP version. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.11 | TableigmpRelayMrtrNewCfgTable | not-accessible | current | The IGMP relay multicast router table in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.11.1 | RowigmpRelayMrtrNewCfgTableEntry | not-accessible | current | A row in the IGMP relay multicast router table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.11.1.1 | ColumnigmpRelayMrtrNewCfgIndx | read-only | current | The IGMP relay multicast router table index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.11.1.2 | ColumnigmpRelayMrtrNewCfgAddr | read-write | current | The IP address of the multicast router. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.11.1.3 | ColumnigmpRelayMrtrNewCfgEnaDis | read-write | current | The status of the multicast router. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.11.1.4 | ColumnigmpRelayMrtrNewCfgInterval | read-write | current | The interval between ping attempts. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.11.1.5 | ColumnigmpRelayMrtrNewCfgRetry | read-write | current | The number of failed attempts to declare router DOWN. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.11.1.6 | ColumnigmpRelayMrtrNewCfgRestr | read-write | current | The number of successful attempts to declare router UP. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.11.1.7 | ColumnigmpRelayMrtrNewCfgVersion | read-write | current | The IGMP version. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.12.11.1.8 | ColumnigmpRelayMrtrNewCfgRemove | read-write | current | Delete the IGMP Relay multicast router. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.13 | NodeigmpAdvCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.13.1 | ScalarigmpAdvCurCfgQInterval | read-only | current | The IGMP Query Interval of current config. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.13.2 | ScalarigmpAdvNewCfgQInterval | read-write | current | The IGMP Query Interval of new config. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.13.3 | ScalarigmpAdvCurCfgRobust | read-only | current | The value of expected packet loss on subnet in current config. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.13.4 | ScalarigmpAdvNewCfgRobust | read-write | current | Set the value of expected packet loss on subnet. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.13.5 | ScalarigmpAdvCurCfgTimeout | read-only | current | The IGMP Report timeout. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.13.6 | ScalarigmpAdvNewCfgTimeout | read-write | current | Set IGMP Report timeout. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.13.7 | ScalarigmpAdvNewCfgVlanFastlvAdd | read-write | current | The VLAN to be added to quick-leave vlan list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.13.8 | ScalarigmpAdvNewCfgVlanFastlvRem | read-write | current | The VLAN to be removed from quick-leave vlan list. When read, 0 is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.13.9 | ScalarigmpAdvCurCfgVlanFastlvBmap | read-only | current | The fast-leave enabled vlans present in the vlan map list. The fast-leave enabled vlans are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 .… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.13.10 | ScalarigmpAdvNewCfgVlanFastlvBmap | read-write | current | The fast-leave enabled vlans present in the vlan map list. The fast-leave enabled vlans are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 .… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.13.15 | ScalarigmpAdvCurCfgRtrAlert | read-only | current | Enable/disable sending IGMP messages with Router Alert option. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.13.16 | ScalarigmpAdvNewCfgRtrAlert | read-write | current | Enable/disable sending IGMP messages with Router Alert option. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.14 | NodeigmpV3SnoopCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.14.1 | ScalarigmpV3SnoopCurCfgSources | read-only | current | Number of sources to snoop in a group record in current config. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.14.2 | ScalarigmpV3SnoopNewCfgSources | read-write | current | Number of sources to snoop in a group record in new config. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.14.3 | ScalarigmpV3SnoopCurCfgEnaDis | read-only | current | The current status of IGMP V3 Snooping. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.14.4 | ScalarigmpV3SnoopNewCfgEnaDis | read-write | current | Set Enable/Disable of IGMP V3 Snooping. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.14.5 | ScalarigmpV3SnoopCurCfgExcludeEnaDis | read-only | current | The current status of IGMP V3 EXCLUDE filter-mode Snooping. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.14.6 | ScalarigmpV3SnoopNewCfgExcludeEnaDis | read-write | current | Set Enable/Disable of IGMP V3 EXCLUDE filter-mode Snooping. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.14.7 | ScalarigmpV3SnoopCurCfgV1V2EnaDis | read-only | current | The current status of IGMP V1/V2 Report Snooping. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.14.8 | ScalarigmpV3SnoopNewCfgV1V2EnaDis | read-write | current | Set Enable/Disable of IGMP V1/V2 Report Snooping. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.15 | TableigmpCurQurCfgTable | not-accessible | current | The table of IGMP querier configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.15.1 | RowigmpCurQurCfgEntry | not-accessible | current | A row in the IGMP querier configuration table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.15.1.1 | ColumnigmpCurQurCfgVlanIndex | read-only | current | The vlan number for which the IGMP querier information is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.15.1.2 | ColumnigmpCurQuerierState | read-only | current | Indicates whether the switch is running as a querier in the VLAN. Based on the querier election, if elected as a querier, it will send query messages. If the s… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.15.1.3 | ColumnigmpCurCfgQuerier | read-only | current | The snooping switch can be configured to send IGMP queries. querier are not present in the VLAN and it set to 'enabled' the switch will generate general query … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.15.1.4 | ColumnigmpCurCfgQueryInterval | read-only | current | This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.15.1.5 | ColumnigmpCurCfgQurSrcIp | read-only | current | The source ip for GSQ proxy in this vlan. This Src Ip will be used in querier election mechanism. It will be the source address in queries sent bye the switch. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.15.1.6 | ColumnigmpCurCfgElectionType | read-only | current | The querier selection type specify the criteria to be used to elect querier for this VLAN. When a switch is configured as a querier, this will define the elect… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.15.1.7 | ColumnigmpCurCfgQurRobustness | read-only | current | The Robustness Variable allows tuning for the Other Querier Present Interval. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.15.1.8 | ColumnigmpCurCfgQurStartupCnt | read-only | current | Represents the number of Queries sent out on startup of querier election, separated by the Startup Query Interval. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.15.1.9 | ColumnigmpCurCfgQurStartupInt | read-only | current | This variable represents the interval(in seconds) between General Queries sent by a Querier on startup. By default: 1/4 the Query Interval. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.15.1.10 | ColumnigmpCurCfgQurMaxRespTime | read-only | current | The maximum query response interval advertised in IGMP queries on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.15.1.11 | ColumnigmpCurCfgOtherQurAddress | read-only | current | The IP/MAC Address of the Querier, which has won the Querier election, when bosSnoopVlanCfgQuerier is enabled on this vlan. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.15.1.12 | ColumnigmpCurCfgOtherQurPresentInt | read-only | current | The Other Querier Present Interval is the length of time that must pass before switch decides that there is no longer another multicast router which should be … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.15.1.13 | ColumnigmpCurCfgVlanOperVersion | read-only | current | Indicates the operating version of the IGMP snooping switch for a specific VLAN. The default operating mode on a specific VLAN is IGMP version 3 i.e, V3(3). Th… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.15.1.14 | ColumnigmpCurVlanOperVersion | read-only | current | Indicates the operating version of the IGMP snooping switch for specific VLAN. The default operating mode on a specific VLAN IGMP version 3 i.e, V3(3). |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.15.1.15 | ColumnigmpCurVlanOlderVerTimer | read-only | current | Indicates the remaining time of lowest operating version of the vlan. For interoperability with multicast routers/switches/Hosts, running older versions of IGM… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.16 | TableigmpNewQurCfgTable | not-accessible | current | The table of IGMP querier configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.16.1 | RowigmpNewQurCfgEntry | not-accessible | current | A row in the IGMP querier configuration table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.16.1.1 | ColumnigmpNewQurCfgVlanIndex | read-only | current | The vlan number for which the IGMP querier information is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.16.1.2 | ColumnigmpNewQuerierState | read-only | current | Indicates whether the switch is running as a querier in the VLAN. Based on the querier election, if elected as a querier, it will send query messages. If the s… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.16.1.3 | ColumnigmpNewCfgQuerier | read-write | current | The snooping switch can be configured to send IGMP queries. querier are not present in the VLAN and it set to 'enabled' the switch will generate general query … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.16.1.4 | ColumnigmpNewCfgQueryInterval | read-write | current | This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.16.1.5 | ColumnigmpNewCfgQurSrcIp | read-write | current | The source ip for GSQ proxy in this vlan. This Src Ip will be used in querier election mechanism. It will be the source address in queries sent bye the switch. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.16.1.6 | ColumnigmpNewCfgElectionType | read-write | current | The querier selection type specify the criteria to be used to elect querier for this VLAN. When a switch is configured as a querier, this will define the elect… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.16.1.7 | ColumnigmpNewCfgQurRobustness | read-write | current | The Robustness Variable allows tuning for the Other Querier Present Interval. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.16.1.8 | ColumnigmpNewCfgQurStartupCnt | read-write | current | Represents the number of Queries sent out on startup of querier election, separated by the Startup Query Interval. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.16.1.9 | ColumnigmpNewCfgQurStartupInt | read-write | current | This variable represents the interval(in seconds) between General Queries sent by a Querier on startup. By default: 1/4 the Query Interval. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.16.1.10 | ColumnigmpNewCfgQurMaxRespTime | read-write | current | The maximum query response interval advertised in IGMP queries on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.16.1.11 | ColumnigmpNewCfgOtherQurAddress | read-only | current | The IP/MAC Address of the Querier, which has won the Querier election, when bosSnoopVlanCfgQuerier is enabled on this vlan. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.16.1.12 | ColumnigmpNewCfgOtherQurPresentInt | read-only | current | The Other Querier Present Interval is the length of time that must pass before switch decides that there is no longer another multicast router which should be … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.16.1.13 | ColumnigmpNewCfgVlanOperVersion | read-write | current | Indicates the operating version of the IGMP snooping switch for a specific VLAN. The default operating mode on a specific VLAN is IGMP version 3 i.e, V3(3). Th… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.16.1.14 | ColumnigmpNewVlanOperVersion | read-only | current | Indicates the operating version of the IGMP snooping switch for specific VLAN. The default operating mode on a specific VLAN IGMP version 3 i.e, V3(3). |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.16.1.15 | ColumnigmpNewVlanOlderVerTimer | read-only | current | Indicates the remaining time of lowest operating version of the vlan. For interoperability with multicast routers/switches/Hosts, running older versions of IGM… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.16.1.16 | ColumnigmpNewCfgQuerierDefault | read-write | current | Action to set the default IGMP Querier settings on a Vlan. Returns other(1) when read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.17 | ScalarigmpCurCfgQuerierOnOff | read-only | current | The current status of IGMP Querier. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.19.18 | ScalarigmpNewCfgQuerierOnOff | read-write | current | Globally turn IGMP Querier On/Off. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20 | NodeipmcStaticRouteCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.1 | ScalaripmcStaticRouteTableMaxSize | read-only | current | The maximum number of rows in the IPMC Static Route table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.2 | TableipmcCurCfgStaticRouteTable | not-accessible | current | The table of static IPMC routes in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.2.1 | RowipmcCurCfgStaticRouteEntry | not-accessible | current | A row in the static IPMC route table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.2.1.1 | ColumnipmcCurCfgStaticRouteIndx | read-only | current | The index of the IPMC static routing table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.2.1.2 | ColumnipmcCurCfgStaticRouteDestIp | read-only | current | The destination IPMC address of this IPMC route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.2.1.3 | ColumnipmcCurCfgStaticRouteVlanId | read-only | current | The vlan id of this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.2.1.4 | ColumnipmcCurCfgStaticRouteHostBmap | read-only | current | The Host ports that are added to this IPMC port bitmap. The selected ports are presented in a bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.2.1.5 | ColumnipmcCurCfgStaticRoutePMrtrBmap | read-only | current | The Primary Mrouter ports that are added to this IPMC port bitmap. The selected ports are presented in a bitmap format in receiving order: OCTET 1 OCTET 2 ....… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.2.1.6 | ColumnipmcCurCfgStaticRouteBMrtrBmap | read-only | current | The Backup Mrouter ports that are added to this IPMC port bitmap. The selected ports are presented in a bitmap format in receiving order: OCTET 1 OCTET 2 .....… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.2.1.7 | ColumnipmcCurCfgStaticRouteVrid | read-only | current | The virtual router id of this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.2.1.8 | ColumnipmcCurCfgStaticRouteAdminkeys | read-only | current | The LACP port adminkey of this route. Adminkeys on five positions alligned to right, separated by commas. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.2.1.9 | ColumnipmcCurCfgStaticRouteTrunks | read-only | current | The trunk list for this IPMC route. The trunks are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ trunk… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.3 | TableipmcNewCfgStaticRouteTable | not-accessible | current | The table of IPMC static routes in the new configuration block. When creating a new route, Destination IP and Vlan id must be set first. The actual change in c… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.3.1 | RowipmcNewCfgStaticRouteEntry | not-accessible | current | A row in the static IPMC route table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.3.1.1 | ColumnipmcNewCfgStaticRouteIndx | read-only | current | The index of the IPMC static routing table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.3.1.2 | ColumnipmcNewCfgStaticRouteDestIp | read-create | current | The destination IPMC address of this route. It must be set along Vlan id before creating new route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.3.1.3 | ColumnipmcNewCfgStaticRouteVlanId | read-create | current | The vlan id of this route. It must be set along Destination IP before creating new route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.3.1.4 | ColumnipmcNewCfgStaticRouteHostBmap | read-only | current | The Host ports that are added to this IPMC port bitmap. The selected ports are presented in a bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.3.1.5 | ColumnipmcNewCfgStaticRoutePMrtrBmap | read-only | current | The Primary Mrouter ports that are added to this IPMC port bitmap. The selected ports are presented in a bitmap format in receiving order: OCTET 1 OCTET 2 ....… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.3.1.6 | ColumnipmcNewCfgStaticRouteBMrtrBmap | read-only | current | The Backup Mrouter ports that are added to this IPMC port bitmap. The selected ports are presented in a bitmap format in receiving order: OCTET 1 OCTET 2 .....… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.3.1.7 | ColumnipmcNewCfgStaticRouteAddPortIndex | read-create | current | The port to be added to this IPMC route. Next step is using ipmcNewCfgStaticRoutePortInfo leaf in order to make the actual change. When creating a new route, b… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.3.1.8 | ColumnipmcNewCfgStaticRouteTrunks | read-only | current | The trunk list for this IPMC route. The trunks are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ trunk… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.3.1.9 | ColumnipmcNewCfgStaticRouteAddTrunk | read-create | current | The trunk group number to be added to this IPMC route. Next step is using ipmcNewCfgStaticRoutePortInfo leaf in order to make the actual change. A '0' value is… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.3.1.10 | ColumnipmcNewCfgStaticRouteRemTrunk | read-create | current | The trunk group number to be removed from this IPMC route. Next step is using ipmcNewCfgStaticRoutePortInfo leaf in order to make the actual change. A '0' valu… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.3.1.11 | ColumnipmcNewCfgStaticRouteAdminkeys | read-only | current | The LACP port adminkeys list for to this IPMC route. Adminkeys on five positions alligned to right, separated by commas |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.3.1.12 | ColumnipmcNewCfgStaticRouteAddAdminkey | read-write | current | The LACP port adminkey to be added to this IPMC route. Next step is using ipmcNewCfgStaticRoutePortInfo leaf in order to make the actual change. A '0' value is… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.3.1.13 | ColumnipmcNewCfgStaticRouteRemAdminkey | read-write | current | The LACP port adminkey to be removed from this IPMC route. Next step is using ipmcNewCfgStaticRoutePortInfo leaf in order to make the actual change. A '0' valu… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.3.1.14 | ColumnipmcNewCfgStaticRoutePortInfo | read-create | current | The Port/Trunk/Adminkey Information to be added to this IPMC route (host/primary/backup). Use it only right after you set a new port/trunk/adminkey to specify … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.3.1.15 | ColumnipmcNewCfgStaticRouteVrid | read-create | current | The virtual router id of this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.3.1.16 | ColumnipmcNewCfgStaticRouteDelete | read-write | current | Delete this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.3.1.17 | ColumnipmcNewCfgStaticRouteRemPortIndex | read-create | current | The port to be removed from this IPMC route. Not allowed to delete ports that are part of trunks. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.20.4 | ScalaripmcStaticRouteClearAll | read-write | current | When set to clear(2),clears all static IPMC routes. Otherwhise nothing is done. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.21 | NodeipStaticNbrCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.21.1 | ScalaripStaticNbrTableMaxSize | read-only | current | The maximum number of rows in the Static NBR Cache table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.21.2 | TableipCurCfgStaticNbrTable | not-accessible | current | The table of static NBR Cache entries in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.21.2.1 | RowipCurCfgStaticNbrEntry | not-accessible | current | A row in the static NBR Cache table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.21.2.1.1 | ColumnipCurCfgStaticNbrIndx | read-only | current | The index of the static NBR Cache table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.21.2.1.2 | ColumnipCurCfgStaticNbrIp | read-only | current | The IP address for the NBR Cache entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.21.2.1.3 | ColumnipCurCfgStaticNbrMAC | read-only | current | The MAC address for the NBR Cache entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.21.2.1.4 | ColumnipCurCfgStaticNbrVlan | read-only | current | The VLAN for the NBR Cache entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.21.2.1.5 | ColumnipCurCfgStaticNbrPortIndex | read-only | current | The port for the NBR Cache entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.21.3 | TableipNewCfgStaticNbrTable | not-accessible | current | The table of static NBR Cache entries in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.21.3.1 | RowipNewCfgStaticNbrEntry | not-accessible | current | A row in the static NBR Cache table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.21.3.1.1 | ColumnipNewCfgStaticNbrIndx | read-only | current | The index of the static NBR Cache table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.21.3.1.2 | ColumnipNewCfgStaticNbrIp | read-create | current | The IP address for the NBR Cache entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.21.3.1.3 | ColumnipNewCfgStaticNbrMAC | read-create | current | The MAC address for the NBR Cache entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.21.3.1.4 | ColumnipNewCfgStaticNbrVlan | read-create | current | The VLAN for the NBR Cache entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.21.3.1.5 | ColumnipNewCfgStaticNbrPortIndex | read-create | current | The port for the NBR Cache entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.21.3.1.6 | ColumnipNewCfgStaticNbrAction | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other is returned. Setting the value to anything other than 2(delete) has no effect … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.21.4 | ScalaripStaticNbrClearAll | read-write | current | When set to clear(2),clears all static NBR Cache entries. Otherwhise nothing is done. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.22 | NodeipGatewayIpv6Cfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.22.1 | ScalaripGatewayIpv6TableMax | read-only | current | The maximum number of rows in the IPv6 gateway table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.22.2 | TableipCurCfgGwIpv6Table | not-accessible | current | The table of IPv6 gateways in the Current configuration Block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.22.2.1 | RowipCurCfgGwIpv6Entry | not-accessible | current | A row in the Ipv6 gateway table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.22.2.1.1 | ColumnipCurCfgGwIpv6Index | read-only | current | The IPv6 gateway number for which the information is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.22.2.1.2 | ColumnipCurCfgGwIpv6Addr | read-only | current | The IPv6 address of the gateway. Address should be 4-byte hexadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.22.2.1.3 | ColumnipCurCfgGwIpv6State | read-only | current | The state of the default IPv6 gateway. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.22.3 | TableipNewCfgGwIpv6Table | not-accessible | current | The table of IPv6 gateways in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.22.3.1 | RowipNewCfgGwIpv6Entry | not-accessible | current | A row in the Ipv6 gateway table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.22.3.1.1 | ColumnipNewCfgGwIpv6Index | read-only | current | The IPv6 gateway number for which the information is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.22.3.1.2 | ColumnipNewCfgGwIpv6Addr | read-create | current | The IPv6 address of the gateway. Address should be 4-byte hexadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.22.3.1.3 | ColumnipNewCfgGwIpv6State | read-create | current | The state of the default IPv6 gateway. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.22.3.1.4 | ColumnipNewCfgGwIpv6Delete | read-create | current | When set to the value of 2 (delete), the default gw is deleted. When read, other is returned. Setting the value to anything other than 2(delete) has no effect … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23 | NodeipStaticRoute6Cfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.1 | ScalaripStaticRoute6TableMaxSize | read-only | current | The maximum number of rows in the Static Route6 table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.2 | TableipCurCfgStaticRoute6Table | not-accessible | current | The table of static IP6 routes in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.2.1 | RowipCurCfgStaticRoute6Entry | not-accessible | current | A row in the static IP6 route table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.2.1.1 | ColumnipCurCfgStaticRoute6Indx | read-only | current | The index of the static IP6 routing table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.2.1.2 | ColumnipCurCfgStaticRoute6DestIp | read-only | current | The destination IP6 address of this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.2.1.3 | ColumnipCurCfgStaticRoute6Mask | read-only | current | The destination IP6 prefix len of this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.2.1.4 | ColumnipCurCfgStaticRoute6Gateway | read-only | current | The IP6 address of the gateway for this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.2.1.5 | ColumnipCurCfgStaticRoute6Interface | read-only | current | The IP6 interface of this route. The IP6 address of the specified interface shall be used as source IP when performs routing. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.3 | TableipNewCfgStaticRoute6Table | not-accessible | current | The table of static IP6 routes in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.3.1 | RowipNewCfgStaticRoute6Entry | not-accessible | current | A row in the static IP6 route table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.3.1.1 | ColumnipNewCfgStaticRoute6Indx | read-only | current | The index of the static IP6 routing table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.3.1.2 | ColumnipNewCfgStaticRoute6DestIp | read-create | current | The destination IP6 address of this route. Address should be 16-byte hexadecimal colon notation. Valid IPv6 address should be in any of the following forms xxx… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.3.1.3 | ColumnipNewCfgStaticRoute6Mask | read-create | current | The prefix length of this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.3.1.4 | ColumnipNewCfgStaticRoute6Gateway | read-create | current | The IP6 address of the gateway for this route. Address should be 16-byte hexadecimal colon notation. Valid IPv6 address should be in any of the following forms… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.3.1.5 | ColumnipNewCfgStaticRoute6Action | read-create | current | Set the value '2' to delete the entire route entry. Value 1 (other) is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.3.1.6 | ColumnipNewCfgStaticRoute6Interface | read-create | current | The IP6 interface of this route. The IP6 address of the specified interface shall be used as source IP when performs routing. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.4 | ScalaripStaticRoute6ClearAllByDestIp | read-write | current | Clears all static IP6 routes with the specified destination IP6 address. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.5 | ScalaripStaticRoute6ClearAllByGatewayIp | read-write | current | Clears all static IP6 routes with the specified gateway IP address. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.6 | ScalaripStaticRoute6ClearAllByInterface | read-write | current | Clears all IP6 routes on the specified inteface number. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.23.7 | ScalaripStaticRoute6ClearAll | read-write | current | When set to clear(2), clears all IP6 static routes. Otherwise nothing is done. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.24 | NodeipInterfaceLoopbackCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.24.1 | ScalaripInterfaceLoopbackTableMax | read-only | current | The maximum number of rows in the IP Loopback interface table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.24.2 | TableipCurCfgIntfLoopbackTable | not-accessible | current | The table of IP Loopback interface configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.24.2.1 | RowipCurCfgIntfLoopbackEntry | not-accessible | current | A row in the Ip Loopback interface table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.24.2.1.1 | ColumnipCurCfgIntfLoopbackIndex | read-only | current | The Loopback interface number for which the IP information is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.24.2.1.2 | ColumnipCurCfgIntfLoopbackAddr | read-only | current | The IP address of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.24.2.1.3 | ColumnipCurCfgIntfLoopbackMask | read-only | current | The subnet mask of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.24.2.1.4 | ColumnipCurCfgIntfLoopbackBroadcast | read-only | current | The broadcast address of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.24.2.1.6 | ColumnipCurCfgIntfLoopbackState | read-only | current | The state of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.24.3 | TableipNewCfgIntfLoopbackTable | not-accessible | current | The table of loopback interface in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.24.3.1 | RowipNewCfgIntfLoopbackEntry | not-accessible | current | A row in the Ip Loopback interface table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.24.3.1.1 | ColumnipNewCfgIntfLoopbackIndex | read-only | current | The Loopback interface number for which the IP information is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.24.3.1.2 | ColumnipNewCfgIntfLoopbackAddr | read-create | current | The IP address of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.24.3.1.3 | ColumnipNewCfgIntfLoopbackMask | read-create | current | The subnet mask of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.24.3.1.6 | ColumnipNewCfgIntfLoopbackState | read-create | current | The state of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.24.3.1.7 | ColumnipNewCfgIntfLoopbackDelete | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26 | Nodeospf3Cfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1 | Nodeospf3General | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.1 | Scalarospf3IntfTableMaxSize | read-only | current | The maximum number of rows in the OSPFv3 Interface table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.2 | Scalarospf3AreaTableMaxSize | read-only | current | The maximum number of rows in the OSPFv3 Area table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.3 | Scalarospf3RangeTableMaxSize | read-only | current | The maximum number of rows in the OSPFv3 Range table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.4 | Scalarospf3ExtRangeTableMaxSize | read-only | current | The maximum number of rows in the OSPFv3 Summary Prefix table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.5 | Scalarospf3RedistTableMaxSize | read-only | current | The maximum number of rows in the OSPFv3 Redist Config table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.6 | Scalarospf3VirtIntfTableMaxSize | read-only | current | The maximum number of rows in the OSPFv3 Virtual Interface table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.7 | Scalarospf3HostTableMaxSize | read-only | current | The maximum number of rows in the OSPFv3 Host table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.8 | Scalarospf3NbrTableMaxSize | read-only | current | The maximum number of rows in the OSPFv3 Neighbor table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.9 | Scalarospf3CurCfgState | read-only | current | OSPFv3 global state. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.10 | Scalarospf3NewCfgState | read-write | current | Globally turn OSPFv3 on or off. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.11 | Scalarospf3CurCfgRouterId | read-only | current | The router ID. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.12 | Scalarospf3NewCfgRouterId | read-create | current | The router ID. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.13 | Scalarospf3CurCfgAbrType | read-only | current | OSPFv3 alternative ABR type. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.14 | Scalarospf3NewCfgAbrType | read-write | current | Set the OSPFv3 alternative ABR type. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.15 | Scalarospf3CurCfgLSDB | read-only | current | The LSDB limit for external LSA. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.16 | Scalarospf3NewCfgLSDB | read-write | current | Set the LSDB limit for external LSA, -1 for none. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.17 | Scalarospf3CurCfgExitOverflow | read-only | current | The exit overflow interval in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.18 | Scalarospf3NewCfgExitOverflow | read-write | current | Set the exit overflow interval in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.19 | Scalarospf3CurCfgReferenceBw | read-only | current | The reference bandwidth for default interface metric calculation. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.20 | Scalarospf3NewCfgReferenceBw | read-write | current | The reference bandwidth for default interface metric calculation. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.21 | Scalarospf3CurCfgSpfDelay | read-only | current | The delay between topology change and SPF calculation. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.22 | Scalarospf3NewCfgSpfDelay | read-write | current | The delay between topology change and SPF calculation. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.23 | Scalarospf3CurCfgSpfHold | read-only | current | The hold time between two consecutive SPF calculation. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.24 | Scalarospf3NewCfgSpfHold | read-write | current | The hold time between two consecutive SPF calculation. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.29 | Scalarospf3CurCfgNssaAsbrDfRtTrans | read-only | current | OSPFv3 state of setting P-bit by an NSSA internal ASBR. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.1.30 | Scalarospf3NewCfgNssaAsbrDfRtTrans | read-write | current | OSPFv3 state of setting P-bit by an NSSA internal ASBR. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.2 | Tableospf3CurCfgAreaTable | not-accessible | current | The table of OSPFv3 area in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.2.1 | Rowospf3CurCfgAreaEntry | not-accessible | current | Information about a OSPFv3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.2.1.1 | Columnospf3CurCfgAreaIndex | read-only | current | The OSPFv3 area number for which the OSPFv3 area table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.2.1.2 | Columnospf3CurCfgAreaId | read-only | current | The IP Address of the OSPFv3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.2.1.3 | Columnospf3CurCfgAreaStbInterval | read-only | current | The stability interval for the NSSA area |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.2.1.4 | Columnospf3CurCfgAreaType | read-only | current | Type of Area. transit(1) stub(2) nssa(3) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.2.1.5 | Columnospf3CurCfgAreaNoSumm | read-only | current | Status disabled(0) enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.2.1.6 | Columnospf3CurCfgAreaDefaultMetric | read-only | current | Metric for stub/NSSA area (1-16777215) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.2.1.7 | Columnospf3CurCfgAreaDefaultMetricType | read-only | current | Metric Type for stub/NSSA area (1-3) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.2.1.8 | Columnospf3CurCfgAreaTranslRole | read-only | current | Translation role for the NSSA area. always(1) candidate(2) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.2.1.9 | Columnospf3CurCfgAreaStatus | read-only | current | Status disabled(0) enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.3 | Tableospf3NewCfgAreaTable | not-accessible | current | The table of OSPFv3 Area configuration in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.3.1 | Rowospf3NewCfgAreaEntry | not-accessible | current | Information about a OSPFv3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.3.1.1 | Columnospf3NewCfgAreaIndex | read-only | current | The OSPFv3 area number for which the OSPFv3 area table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.3.1.2 | Columnospf3NewCfgAreaId | read-create | current | The IP Address of the OSPFv3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.3.1.3 | Columnospf3NewCfgAreaStbInterval | read-create | current | The Stability interval for the NSSA area. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.3.1.4 | Columnospf3NewCfgAreaType | read-write | current | Type of Area. transit(1) stub(2) nssa(3) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.3.1.5 | Columnospf3NewCfgAreaNoSumm | read-create | current | Status disabled(0) enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.3.1.6 | Columnospf3NewCfgAreaDefaultMetric | read-create | current | Metric for stub/NSSA area (1-16777215) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.3.1.7 | Columnospf3NewCfgAreaDefaultMetricType | read-create | current | Metric Type for stub/NSSA area (1-3) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.3.1.8 | Columnospf3NewCfgAreaTranslRole | read-create | current | Translation role for the NSSA area. always(1) candidate(2) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.3.1.9 | Columnospf3NewCfgAreaStatus | read-write | current | Status disabled(0) enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.3.1.10 | Columnospf3NewCfgAreaDelete | read-write | current | Delete the area no(0), yes(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.4 | Tableospf3CurCfgHostTable | not-accessible | current | The table of OSPFv3 Host configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.4.1 | Rowospf3CurCfgHostEntry | not-accessible | current | Information about a OSPFv3 host. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.4.1.1 | Columnospf3CurCfgHostIndex | read-only | current | The OSPFv3 host number for which the OSPFv3 host table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.4.1.2 | Columnospf3CurCfgHostIpAddr | read-only | current | The IPv6 Address of the OSPFv3 host. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.4.1.3 | Columnospf3CurCfgHostAreaIndex | read-only | current | The area index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.4.1.4 | Columnospf3CurCfgHostCost | read-only | current | The cost of the OSPFv3 host. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.4.1.5 | Columnospf3CurCfgHostState | read-only | current | Enable or disable an OSPFv3 Host |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.5 | Tableospf3NewCfgHostTable | not-accessible | current | The table of OSPFv3 Host configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.5.1 | Rowospf3NewCfgHostEntry | not-accessible | current | Information about a OSPFv3 host. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.5.1.1 | Columnospf3NewCfgHostIndex | read-only | current | The OSPFv3 host number for which the OSPFv3 host table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.5.1.2 | Columnospf3NewCfgHostIpAddr | read-create | current | The IP6 Address of the OSPFv3 host. Address should be 4-byte haxadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:x… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.5.1.3 | Columnospf3NewCfgHostAreaIndex | read-create | current | The OSPFv3 area index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.5.1.4 | Columnospf3NewCfgHostCost | read-create | current | The cost of the OSPFv3 host. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.5.1.5 | Columnospf3NewCfgHostState | read-create | current | Enable or disable an OSPFv3 Host |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.5.1.6 | Columnospf3NewCfgHostDelete | read-write | current | Delete the OSPFv3 host: no(0), yes(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.6 | Tableospf3CurCfgNbrTable | not-accessible | current | The table of OSPFv3 Neighbor configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.6.1 | Rowospf3CurCfgNbrEntry | not-accessible | current | Information about a OSPFv3 neighbor. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.6.1.1 | Columnospf3CurCfgNbrIndex | read-only | current | The OSPFv3 neighbor number for which the OSPFv3 neighbor table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.6.1.2 | Columnospf3CurCfgNbrIpAddr | read-only | current | The IPv6 Address of the OSPFv3 neighbor. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.6.1.3 | Columnospf3CurCfgNbrIntfIndex | read-only | current | The interface index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.6.1.4 | Columnospf3CurCfgNbrPriority | read-only | current | The priority of the OSPFv3 neighbor. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.6.1.5 | Columnospf3CurCfgNbrState | read-only | current | Enable or disable an OSPFv3 neighbor |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.7 | Tableospf3NewCfgNbrTable | not-accessible | current | The table of OSPFv3 Neighbor configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.7.1 | Rowospf3NewCfgNbrEntry | not-accessible | current | Information about a OSPFv3 neighbor. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.7.1.1 | Columnospf3NewCfgNbrIndex | read-only | current | The OSPFv3 neighbor number for which the OSPFv3 neighbor table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.7.1.2 | Columnospf3NewCfgNbrIpAddr | read-create | current | The IP6 Address of the OSPFv3 neighbor. Address should be 4-byte haxadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xx… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.7.1.3 | Columnospf3NewCfgNbrIntfIndex | read-create | current | The OSPFv3 interface index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.7.1.4 | Columnospf3NewCfgNbrPriority | read-create | current | The cost of the OSPFv3 neighbor. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.7.1.5 | Columnospf3NewCfgNbrState | read-create | current | Enable or disable an OSPFv3 Neighbor |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.7.1.6 | Columnospf3NewCfgNbrDelete | read-write | current | Delete the OSPFv3 neighbor: no(0), yes(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8 | Tableospf3CurCfgIntfTable | not-accessible | current | The table of OSPFv3 Interface in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1 | Rowospf3CurCfgIntfEntry | not-accessible | current | Information about an OSPFv3 Interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.1 | Columnospf3CurCfgIntfIndex | read-only | current | The OSPFv3 Interface number for which the OSPFv3 Interface table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.2 | Columnospf3CurCfgIntfInstId | read-only | current | Interface Instance Id |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.3 | Columnospf3CurCfgIntfArea | read-only | current | The index of the area that the interface belongs |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.4 | Columnospf3CurCfgIntfCost | read-only | current | Interface cost |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.5 | Columnospf3CurCfgIntfPrio | read-only | current | Interface router priority |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.6 | Columnospf3CurCfgIntfHello | read-only | current | Hello interval |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.7 | Columnospf3CurCfgIntfDead | read-only | current | Dead interval |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.8 | Columnospf3CurCfgIntfPoll | read-only | current | Poll interval(1..4294967295) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.9 | Columnospf3CurCfgIntfTrans | read-only | current | Transmit delay |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.10 | Columnospf3CurCfgIntfRetra | read-only | current | Retransmit interval |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.11 | Columnospf3CurCfgIntfPassive | read-only | current | Passive interface disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.12 | Columnospf3CurCfgIntfNetworkType | read-only | current | Network Type. broadcast(1), non-broadcast(2), point-to-point(3), point-to-multipoint(4) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.16 | Columnospf3CurCfgIntfStatus | read-only | current | Status of the interface disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.17 | Columnospf3CurCfgIntfAuthSpi | read-only | current | Spi Id(256 - 4294967295) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.18 | Columnospf3CurCfgIntfAuthEnable | read-only | current | Status disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.19 | Columnospf3CurCfgIntfAuthType | read-only | current | Authentication Type none(0), md5(2), sha1(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.20 | Columnospf3CurCfgIntfAuthKey | read-only | current | Authentication Key Hex-string MD5 key - 32 chars (128 bits) Hex-string SHA-1 key - 40 chars (160 bits) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.21 | Columnospf3CurCfgIntfEncrySpi | read-only | current | Spi Id(256 - 4294967295) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.22 | Columnospf3CurCfgIntfEncryEnable | read-only | current | Status disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.23 | Columnospf3CurCfgIntfEncryType | read-only | current | Encryption Type null(0), 3des(2), aes(3) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.24 | Columnospf3CurCfgIntfEncryKey | read-only | current | Encryption Key Hex-string AES key - 32 chars (128 bits) Hex-string 3DES key - 48 chars (192 bits) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.25 | Columnospf3CurCfgIntfEncryAuthType | read-only | current | Encryption Authentication Type none(0), md5(2), sha1(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.26 | Columnospf3CurCfgIntfEncryAuthKey | read-only | current | Encryption Authentication Key Hex-string MD5 key - 32 chars (128 bits) Hex-string SHA-1 key - 40 chars (160 bits) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.8.1.27 | Columnospf3CurCfgIntfLsaSupress | read-only | current | LSA Supression on interface disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9 | Tableospf3NewCfgIntfTable | not-accessible | current | The table of OSPFv3 interface in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1 | Rowospf3NewCfgIntfEntry | not-accessible | current | Information about an OSPFv3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.1 | Columnospf3NewCfgIntfIndex | read-only | current | The OSPFv3 Interface number for which the OSPFv3 Interface table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.2 | Columnospf3NewCfgIntfInstId | read-create | current | Interface Instance Id (0..255) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.3 | Columnospf3NewCfgIntfArea | read-create | current | The index of the area that the interface belongs (0..2) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.4 | Columnospf3NewCfgIntfCost | read-create | current | Interface cost(1..65535) and 0 for none |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.5 | Columnospf3NewCfgIntfPrio | read-create | current | Interface router priority(0..255) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.6 | Columnospf3NewCfgIntfHello | read-create | current | Hello interval(1..65535) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.7 | Columnospf3NewCfgIntfDead | read-create | current | Dead interval(1..65535) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.8 | Columnospf3NewCfgIntfPoll | read-create | current | Poll interval(1..4294967295) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.9 | Columnospf3NewCfgIntfTrans | read-create | current | Transmit delay(1..1800) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.10 | Columnospf3NewCfgIntfRetra | read-create | current | Retransmit interval(1..1800) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.11 | Columnospf3NewCfgIntfPassive | read-create | current | Passive interface disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.12 | Columnospf3NewCfgIntfNetworkType | read-create | current | Network Type. broadcast(1), non-broadcast(2), point-to-point(3), point-to-multipoint(4) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.16 | Columnospf3NewCfgIntfStatus | read-create | current | Status of the interface disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.17 | Columnospf3NewCfgIntfDelete | read-write | current | Delete the interface other(0), delete(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.18 | Columnospf3NewCfgIntfAuthSpi | read-write | current | Authentication Spi Id(256 - 4294967295) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.19 | Columnospf3NewCfgIntfAuthEnable | read-write | current | Authentication Status disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.20 | Columnospf3NewCfgIntfAuthType | read-write | current | Authentication Type none(0), md5(2), sha1(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.21 | Columnospf3NewCfgIntfAuthKey | read-write | current | Authentication Type Hex-string MD5 key - 32 chars (128 bits), Hex-string SHA-1 key - 40 chars (160 bits) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.22 | Columnospf3NewCfgIntfAuthReset | read-write | current | Reset AH configuration other(0), reset(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.23 | Columnospf3NewCfgIntfEncrySpi | read-write | current | Encryption Spi Id(256 - 4294967295) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.24 | Columnospf3NewCfgIntfEncryEnable | read-write | current | Encryption Status disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.25 | Columnospf3NewCfgIntfEncryType | read-write | current | Encryption Type null(0), 3des(2), aes(3) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.26 | Columnospf3NewCfgIntfEncryKey | read-write | current | Encryption Key Hex-string AES key - 32 chars (128 bits) Hex-string 3DES key - 48 chars (192 bits) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.27 | Columnospf3NewCfgIntfEncryAuthType | read-write | current | Encryption Authentication Type none(0), md5(2), sha1(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.28 | Columnospf3NewCfgIntfEncryAuthKey | read-write | current | Encryption Authentication Key Hex-string MD5 key - 32 chars (128 bits), Hex-string SHA-1 key - 40 chars (160 bits) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.29 | Columnospf3NewCfgIntfEncryReset | read-write | current | Reset Encryption configuration other(0), reset(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.9.1.30 | Columnospf3NewCfgIntfLsaSupress | read-create | current | LSA Supression on interface disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.10 | Tableospf3CurCfgVirtIntfTable | not-accessible | current | The table of OSPFv3 Virtual Interface configuration in the current configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.10.1 | Rowospf3CurCfgVirtIntfEntry | not-accessible | current | Information about an OSPFv3v3 virtual Interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.10.1.1 | Columnospf3CurCfgVirtIntfIndex | read-only | current | The OSPFv3 Virtual Interface number for which the OSPFv3 Virtual Interface table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.10.1.3 | Columnospf3CurCfgVirtIntfAreaId | read-only | current | The index of the OSPFv3 area to which this virtual interface belongs. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.10.1.4 | Columnospf3CurCfgVirtIntfNbr | read-only | current | The IP Address of the OSPFv3 neighbor for this virtual interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.10.1.5 | Columnospf3CurCfgVirtIntfHello | read-only | current | Hello interval |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.10.1.6 | Columnospf3CurCfgVirtIntfDead | read-only | current | Dead interval |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.10.1.7 | Columnospf3CurCfgVirtIntfTrans | read-only | current | Transmit delay |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.10.1.8 | Columnospf3CurCfgVirtIntfRetra | read-only | current | Retransmit interval |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.10.1.9 | Columnospf3CurCfgVirtIntfStatus | read-only | current | Status disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.11 | Tableospf3NewCfgVirtIntfTable | not-accessible | current | The table of OSPFv3 Virtual interface in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.11.1 | Rowospf3NewCfgVirtIntfEntry | not-accessible | current | Information about an OSPFv3 virtual interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.11.1.1 | Columnospf3NewCfgVirtIntfIndex | read-only | current | The OSPFv3 Virtual Interface number for which the OSPFv3 Virtual Interface table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.11.1.3 | Columnospf3NewCfgVirtIntfAreaId | read-create | current | The index of the OSPFv3 area to which this virtual interface belongs. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.11.1.4 | Columnospf3NewCfgVirtIntfNbr | read-create | current | The IP Address of the OSPFv3 neighbor for this virtual interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.11.1.5 | Columnospf3NewCfgVirtIntfHello | read-create | current | Hello interval(1..65535) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.11.1.6 | Columnospf3NewCfgVirtIntfDead | read-create | current | Dead interval(1..65535) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.11.1.7 | Columnospf3NewCfgVirtIntfTrans | read-create | current | Transmit delay(1..3600) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.11.1.8 | Columnospf3NewCfgVirtIntfRetra | read-create | current | Retransmit interval(1..3600) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.11.1.9 | Columnospf3NewCfgVirtIntfStatus | read-create | current | Status disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.11.1.10 | Columnospf3NewCfgVirtIntfDelete | read-write | current | Delete other(0), delete(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.12 | Tableospf3CurCfgRangeTable | not-accessible | current | The table of OSPFv3 summary range in the current configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.12.1 | Rowospf3CurCfgRangeEntry | not-accessible | current | Information about an OSPFv3 summary range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.12.1.1 | Columnospf3CurCfgRangeIndex | read-only | current | The range number for which the OSPFv3 summary range table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.12.1.2 | Columnospf3CurCfgRangeAddr | read-only | current | The IPv6 Address of the range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.12.1.3 | Columnospf3CurCfgRangePrefixLen | read-only | current | The prefix length of the range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.12.1.4 | Columnospf3CurCfgRangeAreaIndex | read-only | current | The area index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.12.1.5 | Columnospf3CurCfgRangeHideState | read-only | current | The state of the hide range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.12.1.6 | Columnospf3CurCfgRangeLsaType | read-only | current | The LSA type for aggregation. summary(8195), type7(8199) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.12.1.7 | Columnospf3CurCfgRangeRouteTag | read-only | current | The route tag of the range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.12.1.8 | Columnospf3CurCfgRangeState | read-only | current | The state of the range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.13 | Tableospf3NewCfgRangeTable | not-accessible | current | The table of OSPFv3 summary range in the new configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.13.1 | Rowospf3NewCfgRangeEntry | not-accessible | current | Information about an OSPFv3 summary range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.13.1.1 | Columnospf3NewCfgRangeIndex | read-only | current | The range number for which the OSPFv3 summary range table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.13.1.2 | Columnospf3NewCfgRangeAddr | read-create | current | The IPv6 Address of the range. Address should be 4-byte haxadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx:x… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.13.1.3 | Columnospf3NewCfgRangePrefixLen | read-create | current | The prefix length of the range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.13.1.4 | Columnospf3NewCfgRangeAreaIndex | read-create | current | The area index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.13.1.5 | Columnospf3NewCfgRangeHideState | read-create | current | The state of the hide range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.13.1.6 | Columnospf3NewCfgRangeLsaType | read-create | current | The LSA type for aggregation. summary(8195), type7(8199) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.13.1.7 | Columnospf3NewCfgRangeRouteTag | read-create | current | The route tag of the range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.13.1.8 | Columnospf3NewCfgRangeState | read-create | current | The state of the range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.13.1.9 | Columnospf3NewCfgRangeDelete | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.14 | Tableospf3CurCfgExtRangeTable | not-accessible | current | The table of OSPFv3 AS-External range in the current configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.14.1 | Rowospf3CurCfgExtRangeEntry | not-accessible | current | Information about an OSPFv3 AS-External range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.14.1.1 | Columnospf3CurCfgExtRangeIndex | read-only | current | The range number for which the OSPFv3 AS-External range table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.14.1.2 | Columnospf3CurCfgExtRangeAddr | read-only | current | The IPv6 Address of the AS-External range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.14.1.3 | Columnospf3CurCfgExtRangePrefixLen | read-only | current | The prefix length of the AS-External range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.14.1.4 | Columnospf3CurCfgExtRangeAreaIndex | read-only | current | The area index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.14.1.5 | Columnospf3CurCfgExtRangeTranslation | read-only | current | The state of the setting the P-bit in the generated LSA. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.14.1.6 | Columnospf3CurCfgExtRangeAggrEffect | read-only | current | The aggregation effect. advertise(1), not-advertise(2), allowAll(3), denyAll(4) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.14.1.7 | Columnospf3CurCfgExtRangeState | read-only | current | The state of the AS-External range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.15 | Tableospf3NewCfgExtRangeTable | not-accessible | current | The table of OSPFv3 summary AS-External range in the new configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.15.1 | Rowospf3NewCfgExtRangeEntry | not-accessible | current | Information about an OSPFv3 summary AS-External range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.15.1.1 | Columnospf3NewCfgExtRangeIndex | read-only | current | The range number for which the OSPFv3 AS-External range table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.15.1.2 | Columnospf3NewCfgExtRangeAddr | read-create | current | The IPv6 Address of the AS-External range. Address should be 4-byte haxadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.15.1.3 | Columnospf3NewCfgExtRangePrefixLen | read-create | current | The prefix length of the AS-External range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.15.1.4 | Columnospf3NewCfgExtRangeAreaIndex | read-create | current | The area index. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.15.1.5 | Columnospf3NewCfgExtRangeTranslation | read-create | current | The state of the setting the P-bit in the generated LSA. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.15.1.6 | Columnospf3NewCfgExtRangeAggrEffect | read-create | current | The aggregation effect. advertise(1), not-advertise(2), allowAll(3), denyAll(4) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.15.1.7 | Columnospf3NewCfgExtRangeState | read-create | current | The state of the AS-External range. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.15.1.8 | Columnospf3NewCfgExtRangeDelete | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.16 | Tableospf3CurCfgRedistTable | not-accessible | current | The table of OSPFv3 redistribution entries in the current configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.16.1 | Rowospf3CurCfgRedistEntry | not-accessible | current | Information about an OSPFv3 redistribution entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.16.1.1 | Columnospf3CurCfgRedistIndex | read-only | current | The redistribution entry number for which the OSPFv3 redistribution entry table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.16.1.2 | Columnospf3CurCfgRedistAddr | read-only | current | The IPv6 Address of the redistribution entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.16.1.3 | Columnospf3CurCfgRedistPrefixLen | read-only | current | The prefix length of the redistribution entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.16.1.4 | Columnospf3CurCfgRedistMetric | read-only | current | The metric to be applied to the route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.16.1.5 | Columnospf3CurCfgRedistMetricType | read-only | current | The metric type. asExttype1(3), asExttype2(4) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.16.1.6 | Columnospf3CurCfgRedistRouteTag | read-only | current | The route tag of the redistribution entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.16.1.7 | Columnospf3CurCfgRedistRouteTagTypeManual | read-only | current | Indicates if the route tag is set manually. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.16.1.8 | Columnospf3CurCfgRedistState | read-only | current | The state of the redistribution entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.17 | Tableospf3NewCfgRedistTable | not-accessible | current | The table of OSPFv3 summary redistribution entry in the new configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.17.1 | Rowospf3NewCfgRedistEntry | not-accessible | current | Information about an OSPFv3 summary redistribution entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.17.1.1 | Columnospf3NewCfgRedistIndex | read-only | current | The redistribution entry number for which the OSPFv3 redistribution entry table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.17.1.2 | Columnospf3NewCfgRedistAddr | read-create | current | The IPv6 Address of the redistribution entry. Address should be 4-byte haxadecimal colon notation. Valid IPv6 address should be in any of the following forms x… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.17.1.3 | Columnospf3NewCfgRedistPrefixLen | read-create | current | The prefix length of the redistribution entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.17.1.4 | Columnospf3NewCfgRedistMetric | read-create | current | The metric to be applied to the route. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.17.1.5 | Columnospf3NewCfgRedistMetricType | read-create | current | The metric type. asExttype1(3), asExttype2(4) |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.17.1.6 | Columnospf3NewCfgRedistRouteTag | read-create | current | The route tag of the redistribution entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.17.1.7 | Columnospf3NewCfgRedistRouteTagTypeManual | read-write | current | Indicates if the route tag is set manually. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.17.1.8 | Columnospf3NewCfgRedistState | read-create | current | The state of the redistribution entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.17.1.9 | Columnospf3NewCfgRedistDelete | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effe… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.18 | Nodeospf3RouteRedistribution | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.18.1 | Nodeospf3RedistributeConnected | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.18.1.1 | Scalarospf3CurCfgConnectedMetric | read-only | current | The metric to be assigned to Connected routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.18.1.2 | Scalarospf3NewCfgConnectedMetric | read-write | current | The metric to be assigned to Connected routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.18.1.3 | Scalarospf3CurCfgConnectedMetricType | read-only | current | The AS External metric type for Connected routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.18.1.4 | Scalarospf3NewCfgConnectedMetricType | read-write | current | The AS External metric type for Connected routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.18.1.5 | Scalarospf3CurCfgConnectedRouteTag | read-only | current | Assigned route tag |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.18.1.6 | Scalarospf3NewCfgConnectedRouteTag | read-write | current | Assigned route tag |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.18.1.7 | Scalarospf3CurCfgConnectedRouteTagTypeManual | read-only | current | Indicates if the route tag is set manually. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.18.1.8 | Scalarospf3NewCfgConnectedRouteTagTypeManual | read-write | current | Indicates if the route tag is set manually. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.18.2 | Nodeospf3RedistributeStatic | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.18.2.1 | Scalarospf3CurCfgStaticMetric | read-only | current | The metric to be assigned to static routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.18.2.2 | Scalarospf3NewCfgStaticMetric | read-write | current | The metric to be assigned to static routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.18.2.3 | Scalarospf3CurCfgStaticMetricType | read-only | current | The AS External metric type for static routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.18.2.4 | Scalarospf3NewCfgStaticMetricType | read-write | current | The AS External metric type for static routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.18.2.5 | Scalarospf3CurCfgStaticRouteTag | read-only | current | Assigned route tag |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.18.2.6 | Scalarospf3NewCfgStaticRouteTag | read-write | current | Assigned route tag |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.18.2.7 | Scalarospf3CurCfgStaticRouteTagTypeManual | read-only | current | Indicates if the route tag is set manually. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.26.18.2.8 | Scalarospf3NewCfgStaticRouteTagTypeManual | read-write | current | Indicates if the route tag is set manually. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.27 | NodepptCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.27.1 | ScalarpptTableMaxSize | read-only | current | The maximum number of rows in the Prefix policy table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.27.2 | TablepptCurCfgTable | not-accessible | current | The table of prefix policy table entries in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.27.2.1 | RowpptCurCfgEntry | not-accessible | current | A row in the prefix policy table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.27.2.1.1 | ColumnpptCurCfgIndx | read-only | current | The index of the prefix policy table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.27.2.1.2 | ColumnpptCurCfgPrefix | read-only | current | The prefix address for the prefix policy table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.27.2.1.3 | ColumnpptCurCfgPrefixLen | read-only | current | The prefix length for the prefix policy table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.27.2.1.4 | ColumnpptCurCfgPrecedence | read-only | current | The precedence for the prefix policy table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.27.2.1.5 | ColumnpptCurCfgLabel | read-only | current | The label for the prefix policy table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.27.3 | TablepptNewCfgTable | not-accessible | current | The table of prefix policy table entries in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.27.3.1 | RowpptNewCfgEntry | not-accessible | current | A row in the prefix policy table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.27.3.1.1 | ColumnpptNewCfgIndx | read-only | current | The index of the prefix policy table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.27.3.1.2 | ColumnpptNewCfgPrefix | read-create | current | The prefix address for the prefix policy table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.27.3.1.3 | ColumnpptNewCfgPrefixLen | read-create | current | The prefix length the prefix policy table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.27.3.1.4 | ColumnpptNewCfgPrecedence | read-create | current | The precedence for the prefix policy table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.27.3.1.5 | ColumnpptNewCfgLabel | read-create | current | The label for the prefix policy table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.27.3.1.6 | ColumnpptNewCfgAction | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When read, other is returned. Setting the value to anything other than 2(delete) has no effect … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.28 | Nodeipv6pmtuCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.28.1 | Scalaripv6PmtuCurTimeout | read-only | current | IPv6 PMTU Expired Time Value(0|10-100), 0 indicates INFINITY. Other values should be in [10, 100] |
| 1.3.6.1.4.1.26543.2.7.7.3.1.28.2 | Scalaripv6PmtuNewTimeout | read-write | current | IPv6 PMTU Expired Time Value(0|10-100), 0 indicates INFINITY. Other values should be in [10, 100] |
| 1.3.6.1.4.1.26543.2.7.7.3.1.28.3 | Scalaripv6PmtuEntriesClearAll | read-write | current | When set to clear(2),clears all ipv6 PMTU entries. Otherwhise nothing is done. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.29 | NodefloodingCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.29.1 | TablevlanFloodCurCfgTable | not-accessible | current | The table of VLAN flooding configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.29.1.1 | RowvlanFloodCurCfgTableEntry | not-accessible | current | A row in the VLAN flooding configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.29.1.1.1 | ColumnvlanFloodCurCfgVlanId | read-only | current | The VLAN identifier. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.29.1.1.2 | ColumnvlanFloodCurCfgFlood | read-only | current | Enable or disable flooding unregistered IPMCs |
| 1.3.6.1.4.1.26543.2.7.7.3.1.29.1.1.3 | ColumnvlanFloodCurCfgCpu | read-only | current | Enable or disable sending unregistered IPMCs to CPU |
| 1.3.6.1.4.1.26543.2.7.7.3.1.29.1.1.4 | ColumnvlanFloodCurCfgOptFlood | read-only | current | Enable or disable optimized flooding |
| 1.3.6.1.4.1.26543.2.7.7.3.1.29.2 | TablevlanFloodNewCfgTable | not-accessible | current | The table of VLAN flooding configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.29.2.1 | RowvlanFloodNewCfgTableEntry | not-accessible | current | A row in the VLAN flooding configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.29.2.1.1 | ColumnvlanFloodNewCfgVlanId | read-only | current | The VLAN identifier. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.29.2.1.2 | ColumnvlanFloodNewCfgFlood | read-write | current | Enable or disable flooding unregistered IPMCs |
| 1.3.6.1.4.1.26543.2.7.7.3.1.29.2.1.3 | ColumnvlanFloodNewCfgCpu | read-write | current | Enable or disable sending unregistered IPMCs to CPU |
| 1.3.6.1.4.1.26543.2.7.7.3.1.29.2.1.4 | ColumnvlanFloodNewCfgOptFlood | read-write | current | Enable or disable optimized flooding |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30 | NodemldCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.1 | ScalarmldCurCfgState | read-only | current | MLD global state. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.2 | ScalarmldNewCfgState | read-write | current | MLD global state. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.3 | TablemldCurInterfaceTable | not-accessible | current | The (conceptual) table listing the interfaces on which MLD is enabled. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.3.1 | RowmldCurInterfaceEntry | not-accessible | current | An entry (conceptual row) representing an interface on which MLD is enabled. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.3.1.1 | ColumnmldCurInterfaceIfIndex | read-only | current | The internetwork-layer interface value of the interface for which MLD is enabled. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.3.1.2 | ColumnmldCurInterfaceQueryInterval | read-only | current | The frequency at which MLD Host-Query packets are transmitted on this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.3.1.3 | ColumnmldCurInterfaceVersion | read-only | current | The version of MLD which is running on this interface. This object is a place holder to allow for new versions of MLD to be introduced. Version 1 of MLD is def… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.3.1.4 | ColumnmldCurInterfaceQueryMaxResponseIntvl | read-only | current | The maximum query response time advertised in MLD queries on this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.3.1.5 | ColumnmldCurInterfaceRobustness | read-only | current | The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.3.1.6 | ColumnmldCurInterfaceLastListenQueryIntvl | read-only | current | The Last Member Query Interval is the Max Response Delay inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.3.1.7 | ColumnmldCurInterfaceDMrtrEna | read-only | current | Dynamic MRouter learning. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.3.1.8 | ColumnmldCurInterfaceState | read-only | current | State of the MLD interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.4 | TablemldNewInterfaceTable | not-accessible | current | The (conceptual) table listing the interfaces on which MLD is enabled. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.4.1 | RowmldNewInterfaceEntry | not-accessible | current | An entry (conceptual row) representing an interface on which MLD is enabled. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.4.1.1 | ColumnmldNewInterfaceIfIndex | read-only | current | The internetwork-layer interface value of the interface for which MLD is enabled. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.4.1.2 | ColumnmldNewInterfaceQueryInterval | read-write | current | The frequency at which MLD Host-Query packets are transmitted on this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.4.1.3 | ColumnmldNewInterfaceVersion | read-write | current | The version of MLD which is running on this interface. This object is a place holder to allow for new versions of MLD to be introduced. Version 1 of MLD is def… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.4.1.4 | ColumnmldNewInterfaceQueryMaxResponseIntvl | read-write | current | The maximum query response time advertised in MLD queries on this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.4.1.5 | ColumnmldNewInterfaceRobustness | read-write | current | The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.4.1.6 | ColumnmldNewInterfaceLastListenQueryIntvl | read-write | current | The Last Member Query Interval is the Max Response Delay inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.4.1.7 | ColumnmldNewInterfaceDMrtrEna | read-write | current | Dynamic MRouter learning. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.4.1.8 | ColumnmldNewInterfaceState | read-write | current | State of the MLD interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.4.1.9 | ColumnmldNewInterfaceDefault | read-write | current | Action to set the MLD interface configuration to default. Returns other(1) when read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.30.5 | ScalarmldDefaultCfgState | read-write | current | Action to set the global MLD configuration to default. Returns other(1) when read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31 | NodendprefixCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.1 | ScalarndprefixTableMaxSize | read-only | current | The maximum number of rows in the NDPrefix table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.2 | TablendprefixCurCfgTable | not-accessible | current | The ndprefix table entries in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.2.1 | RowndprefixCurCfgEntry | not-accessible | current | A row in the ndprefix table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.2.1.1 | ColumnndprefixCurCfgIndx | read-only | current | The index of the ndprefix table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.2.1.2 | ColumnndprefixCurCfgPrefix | read-only | current | The prefix address for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.2.1.3 | ColumnndprefixCurCfgPrefixLen | read-only | current | The prefix length for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.2.1.4 | ColumnndprefixCurCfgInterfaceIndex | read-only | current | The interface index for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.2.1.5 | ColumnndprefixCurCfgProfileIndex | read-only | current | The profile index for the prefix table entry Profile 0 is the default profile. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.2.1.6 | ColumnndprefixCurCfgValidLifetime | read-only | current | The Valid lifetime for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.2.1.7 | ColumnndprefixCurCfgValidLifetimeFlag | read-only | current | The Valid lifetime fixed flag for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.2.1.8 | ColumnndprefixCurCfgPreferredLifetime | read-only | current | The Preferred Lifetime for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.2.1.9 | ColumnndprefixCurCfgPreferredLifetimeFlag | read-only | current | The Preferred Lifetime fixed flag for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.2.1.10 | ColumnndprefixCurCfgOnlinkFlag | read-only | current | The Onlink flag for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.2.1.11 | ColumnndprefixCurCfgAutonomousFlag | read-only | current | The Autonomous flag for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.2.1.12 | ColumnndprefixCurCfgState | read-only | current | The state for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.3 | TablendprefixNewCfgTable | not-accessible | current | The ndprefix table entries in the new configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.3.1 | RowndprefixNewCfgEntry | not-accessible | current | A row in the prefix table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.3.1.1 | ColumnndprefixNewCfgIndx | read-only | current | The index of the prefix table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.3.1.2 | ColumnndprefixNewCfgPrefix | read-create | current | The prefix address for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.3.1.3 | ColumnndprefixNewCfgPrefixLen | read-create | current | The prefix length for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.3.1.4 | ColumnndprefixNewCfgInterfaceIndex | read-create | current | The interface index for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.3.1.5 | ColumnndprefixNewCfgProfileIndex | read-create | current | The profile index for the prefix table entry. Profile 0 is the default profile. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.3.1.6 | ColumnndprefixNewCfgValidLifetime | read-create | current | The Valid lifetime for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.3.1.7 | ColumnndprefixNewCfgValidLifetimeFlag | read-create | current | The Valid lifetime fixed flag for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.3.1.8 | ColumnndprefixNewCfgPreferredLifetime | read-create | current | The Preferred Lifetime for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.3.1.9 | ColumnndprefixNewCfgPreferredLifetimeFlag | read-create | current | The Preferred Lifetime fixed flag for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.3.1.10 | ColumnndprefixNewCfgOnlinkFlag | read-create | current | The Onlink flag for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.3.1.11 | ColumnndprefixNewCfgAutonomousFlag | read-create | current | The Autonomous flag for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.3.1.12 | ColumnndprefixNewCfgState | read-create | current | The state for the prefix table entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.31.3.1.13 | ColumnndprefixNewCfgAction | read-create | current | When set to the value of 2 (delete), the entire row is deleted. When set to the value of 3 (deleteall), all entries are deleted. When read, other is returned. … |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32 | NodeipsecCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1 | NodeikeGroup | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.1 | NodeikeCurCfgProposal | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.1.1 | ScalarikeCurCfgPropCipher | read-only | current | Current encription algorithm used by IKEv2 |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.1.2 | ScalarikeCurCfgPropAuth | read-only | current | Current authentication algorithm used by IKEv2 |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.1.3 | ScalarikeCurCfgPropGroup | read-only | current | Current Diffie-Hellman groups used by IKEv2 |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.2 | NodeikeNewCfgProposal | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.2.1 | ScalarikeNewCfgPropCipher | read-write | current | New encription algorithm used by IKEv2 |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.2.2 | ScalarikeNewCfgPropAuth | read-write | current | New authentication algorithm used by IKEv2 |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.2.3 | ScalarikeNewCfgPropGroup | read-write | current | New Diffie-Hellman groups used by IKEv2 |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.3 | NodeikeCurCfgPsk | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.3.1 | ScalarikeCurCfgPskLocalKey | read-only | current | Current local pre-shared key. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.3.2 | TableikeCurCfgPskRemoteTable | not-accessible | current | The (conceptual) table listing the remote pre-shared key by peer address used by IKEv2. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.3.2.1 | RowikeCurCfgPskRemoteEntry | not-accessible | current | An entry (conceptual row) representing a remote pre-shared key for a peer address. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.3.2.1.1 | ColumnikeCurCfgPskRemoteIndex | read-only | current | The index of ikeCurCfgPskRemoteTable. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.3.2.1.2 | ColumnikeCurCfgPskRemoteAddr | read-only | current | Current IPv6 address of peer. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.3.2.1.3 | ColumnikeCurCfgPskRemoteKey | read-only | current | Current remote pre-shared key. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.3.2.1.4 | ColumnikeCurCfgPskRemoteDelete | read-only | current | Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.4 | NodeikeNewCfgPsk | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.4.1 | ScalarikeNewCfgPskLocalKey | read-write | current | New local pre-shared key. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.4.2 | TableikeNewCfgPskRemoteTable | not-accessible | current | The (conceptual) table listing the remote pre-shared key by peer address used by IKEv2. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.4.2.1 | RowikeNewCfgPskRemoteEntry | not-accessible | current | An entry (conceptual row) representing a remote pre-shared key for a peer address. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.4.2.1.1 | ColumnikeNewCfgPskRemoteIndex | read-only | current | The index of ikeNewCfgPskRemoteTable. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.4.2.1.2 | ColumnikeNewCfgPskRemoteAddr | read-create | current | New IPv6 address of peer. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.4.2.1.3 | ColumnikeNewCfgPskRemoteKey | read-create | current | New remote pre-shared key. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.4.2.1.4 | ColumnikeNewCfgPskRemoteDelete | read-write | current | Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.5 | NodeikeCurCfgIdentity | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.5.1 | ScalarikeCurCfgIdType | read-only | current | Specifies the type of Identification being used. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.5.2 | ScalarikeCurCfgIdData | read-only | current | Value as indicated by the Identification Type. It can be a fully-qualified domain name string (example.com) or a fully-qualified email address string (jsmith@e… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.6 | NodeikeNewCfgIdentity | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.6.1 | ScalarikeNewCfgIdType | read-write | current | Specifies the type of Identification being used. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.6.2 | ScalarikeNewCfgIdData | read-write | current | Value as indicated by the Identification Type. It can be a fully-qualified domain name string (example.com) or a fully-qualified email address string (jsmith@e… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.7 | ScalarikeCurCfgTxTimeout | read-only | current | The value of this object specify the IKEv2 PDU retransmission timeout in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.8 | ScalarikeNewCfgTxTimeout | read-write | current | The value of this object specify the new IKEv2 PDU retransmission timeout. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.9 | ScalarikeCurCfgCookie | read-only | current | Globally enable/disable IKEv2 cookie notify. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.1.10 | ScalarikeNewCfgCookie | read-write | current | Globally enable/disable IKEv2 cookie notify. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2 | NodeipsecGroup | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.1 | ScalaripsecCurCfgState | read-only | current | Globally enable/disable IPsec. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.2 | ScalaripsecNewCfgState | read-write | current | Globally enable/disable IPsec. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.3 | TableipsecCurCfgTxformTable | not-accessible | current | The (conceptual) table listing all of the IPsec transform-set. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.3.1 | RowipsecCurCfgTxformEntry | not-accessible | current | An entry (conceptual row) representing a IPsec transform-set. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.3.1.1 | ColumnipsecCurCfgTxformIndex | read-only | current | The index of ipsecCurCfgTxformTable. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.3.1.2 | ColumnipsecCurCfgTxformAuth | read-only | current | The authentication algorithm of the IPsec transform-set |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.3.1.3 | ColumnipsecCurCfgTxformCipher | read-only | current | The encryption algorithm of the IPsec transform-set |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.3.1.4 | ColumnipsecCurCfgTxformIntegrity | read-only | current | The interity algorithm of the IPsec transform-set |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.3.1.5 | ColumnipsecCurCfgTxformMode | read-only | current | The tunnel/transport mode of the IPsec transform-set |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.3.1.6 | ColumnipsecCurCfgTxformDelete | read-only | current | Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.4 | TableipsecNewCfgTxformTable | not-accessible | current | The (conceptual) table listing all of the new IPsec transform-set to be apply. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.4.1 | RowipsecNewCfgTxformEntry | not-accessible | current | An entry (conceptual row) representing a IPsec transform-set. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.4.1.1 | ColumnipsecNewCfgTxformIndex | read-only | current | The index of ipsecNewCfgTxformTable. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.4.1.2 | ColumnipsecNewCfgTxformAuth | read-create | current | The authentication algorithm of the IPsec transform-set |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.4.1.3 | ColumnipsecNewCfgTxformCipher | read-create | current | The encryption algorithm of the IPsec transform-set |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.4.1.4 | ColumnipsecNewCfgTxformIntegrity | read-create | current | The interity algorithm of the IPsec transform-set |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.4.1.5 | ColumnipsecNewCfgTxformMode | read-create | current | The tunnel/transport mode of the IPsec transform-set |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.4.1.6 | ColumnipsecNewCfgTxformDelete | read-write | current | Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.5 | TableipsecCurCfgSelectorTable | not-accessible | current | The (conceptual) table listing all of the IPsec selector. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.5.1 | RowipsecCurCfgSelectorEntry | not-accessible | current | An entry (conceptual row) representing a IPsec selector. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.5.1.1 | ColumnipsecCurCfgSelectorIndex | read-only | current | The index of ipsecCurCfgSelectorTable. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.5.1.2 | ColumnipsecCurCfgSelectorAction | read-only | current | The action of the IPsec selector |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.5.1.3 | ColumnipsecCurCfgSelectorProto | read-only | current | The protocol of the IPsec selector |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.5.1.4 | ColumnipsecCurCfgSelectorIcmpType | read-only | current | When the protocol of the IPsec selector is icmp(2), This object specify the ICMP type for the traffic selector. 0 = any. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.5.1.6 | ColumnipsecCurCfgSelectorDst | read-only | current | The destination ip address of the IPsec selector |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.5.1.7 | ColumnipsecCurCfgSelectorDstPrefix | read-only | current | The destination ipv6 address prefix length of the IPsec selector |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.5.1.8 | ColumnipsecCurCfgSelectorSrc | read-only | current | The source ip address of the IPsec selector |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.5.1.9 | ColumnipsecCurCfgSelectorDelete | read-only | current | Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.6 | TableipsecNewCfgSelectorTable | not-accessible | current | The (conceptual) table listing all of the IPsec selector. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.6.1 | RowipsecNewCfgSelectorEntry | not-accessible | current | An entry (conceptual row) representing a IPsec selector. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.6.1.1 | ColumnipsecNewCfgSelectorIndex | read-only | current | The index of ipsecNewCfgSelectorTable. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.6.1.2 | ColumnipsecNewCfgSelectorAction | read-create | current | The action of the IPsec selector |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.6.1.3 | ColumnipsecNewCfgSelectorProto | read-create | current | The protocol of the IPsec selector |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.6.1.4 | ColumnipsecNewCfgSelectorIcmpType | read-create | current | When the protocol of the IPsec selector is icmp(2), This object specify the ICMP type for the traffic selector. 0 = any. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.6.1.6 | ColumnipsecNewCfgSelectorDst | read-create | current | The destination ipv6 address of the IPsec selector |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.6.1.7 | ColumnipsecNewCfgSelectorDstPrefix | read-create | current | The destination ipv6 address prefix length of the IPsec selector |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.6.1.8 | ColumnipsecNewCfgSelectorSrc | read-create | current | The source ip address of the IPsec selector |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.6.1.9 | ColumnipsecNewCfgSelectorDelete | read-write | current | Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.7 | TableipsecCurCfgDynamicPolicyTable | not-accessible | current | The (conceptual) table listing all of the IPsec dynamic policies. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.7.1 | RowipsecCurCfgDynamicPolicyEntry | not-accessible | current | An entry (conceptual row) representing a IPsec dynamic policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.7.1.1 | ColumnipsecCurCfgDynamicPolicyIndex | read-only | current | The index of ipsecCurCfgDynamicPolicyTable. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.7.1.2 | ColumnipsecCurCfgDynamicPolicyPeer | read-only | current | The remote peer ip address. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.7.1.3 | ColumnipsecCurCfgDynamicPolicySelector | read-only | current | The traffic selector index for IPsec policy to refer an entry in ipsecCurCfgSelectorTable. 0 = unspecified. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.7.1.4 | ColumnipsecCurCfgDynamicPolicyTxform | read-only | current | The transform set index for IPSec policy to refer an entry in ipsecCurCfgTxformTable. 0 = unspecified. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.7.1.5 | ColumnipsecCurCfgDynamicPolicyLifetime | read-only | current | The SA lifetime for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.7.1.6 | ColumnipsecCurCfgDynamicPolicyPfs | read-only | current | Enable/disable perfect forward security. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.7.1.7 | ColumnipsecCurCfgDynamicPolicyDelete | read-only | current | Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.8 | TableipsecNewCfgDynamicPolicyTable | not-accessible | current | The (conceptual) table listing all of the IPsec dynamic policies. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.8.1 | RowipsecNewCfgDynamicPolicyEntry | not-accessible | current | An entry (conceptual row) representing a IPsec dynamic policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.8.1.1 | ColumnipsecNewCfgDynamicPolicyIndex | read-only | current | The index of ipsecNewCfgDynamicPolicyTable. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.8.1.2 | ColumnipsecNewCfgDynamicPolicyPeer | read-create | current | The remote peer ip address. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.8.1.3 | ColumnipsecNewCfgDynamicPolicySelector | read-create | current | The traffic selector index for IPsec policy to refer an entry in ipsecNewCfgSelectorTable. 0 = unspecified. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.8.1.4 | ColumnipsecNewCfgDynamicPolicyTxform | read-create | current | The transform set index for IPSec policy to refer an entry in ipsecNewCfgTxformTable. 0 = unspecified. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.8.1.5 | ColumnipsecNewCfgDynamicPolicyLifetime | read-create | current | The SA lifetime for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.8.1.6 | ColumnipsecNewCfgDynamicPolicyPfs | read-create | current | Enable/disable perfect forward security. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.8.1.7 | ColumnipsecNewCfgDynamicPolicyDelete | read-write | current | Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.9 | TableipsecCurCfgManualPolicyTable | not-accessible | current | The (conceptual) table listing all of the IPsec manual policies. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.9.1 | RowipsecCurCfgManualPolicyEntry | not-accessible | current | An entry (conceptual row) representing a IPsec manual policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.9.1.1 | ColumnipsecCurCfgManualPolicyIndex | read-only | current | The index of ipsecCurCfgManualPolicyTable. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.9.1.2 | ColumnipsecCurCfgManualPolicyPeer | read-only | current | The remote peer ip address. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.9.1.3 | ColumnipsecCurCfgManualPolicySelector | read-only | current | The traffic selector index for IPsec policy to refer an entry in ipsecCurCfgSelectorTable |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.9.1.4 | ColumnipsecCurCfgManualPolicyTxform | read-only | current | The transform set index for IPSec policy to refer an entry in ipsecCurCfgTxformTable |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.9.1.5 | ColumnipsecCurCfgManualPolicyInAhKey | read-only | current | The AH inbound session key for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.9.1.6 | ColumnipsecCurCfgManualPolicyInAhSpi | read-only | current | The AH inbound SPI for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.9.1.7 | ColumnipsecCurCfgManualPolicyOutAhKey | read-only | current | The AH outbound session key for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.9.1.8 | ColumnipsecCurCfgManualPolicyOutAhSpi | read-only | current | The AH outbound SPI for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.9.1.9 | ColumnipsecCurCfgManualPolicyInEspEncKey | read-only | current | The Esp inbound cipher key for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.9.1.10 | ColumnipsecCurCfgManualPolicyInEspAuthKey | read-only | current | The Esp inbound authenticator key for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.9.1.11 | ColumnipsecCurCfgManualPolicyInEspSpi | read-only | current | The Esp inbound SPI for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.9.1.12 | ColumnipsecCurCfgManualPolicyOutEspEncKey | read-only | current | The Esp outbound cipher key for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.9.1.13 | ColumnipsecCurCfgManualPolicyOutEspAuthKey | read-only | current | The Esp outbound authenticator key for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.9.1.14 | ColumnipsecCurCfgManualPolicyOutEspSpi | read-only | current | The Esp outbound SPI for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.9.1.15 | ColumnipsecCurCfgManualPolicyDelete | read-only | current | Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.10 | TableipsecNewCfgManualPolicyTable | not-accessible | current | The (conceptual) table listing all of the IPsec manual policies. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.10.1 | RowipsecNewCfgManualPolicyEntry | not-accessible | current | An entry (conceptual row) representing a IPsec manual policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.10.1.1 | ColumnipsecNewCfgManualPolicyIndex | read-only | current | The index of ipsecNewCfgManualPolicyTable. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.10.1.2 | ColumnipsecNewCfgManualPolicyPeer | read-create | current | The remote peer ip address. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.10.1.3 | ColumnipsecNewCfgManualPolicySelector | read-create | current | The traffic selector index for IPsec policy to refer an entry in ipsecNewCfgSelectorTable |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.10.1.4 | ColumnipsecNewCfgManualPolicyTxform | read-create | current | The transform set index for IPSec policy to refer an entry in ipsecNewCfgTxformTable |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.10.1.5 | ColumnipsecNewCfgManualPolicyInAhKey | read-create | current | The AH inbound session key for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.10.1.6 | ColumnipsecNewCfgManualPolicyInAhSpi | read-create | current | The AH inbound SPI for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.10.1.7 | ColumnipsecNewCfgManualPolicyOutAhKey | read-create | current | The AH outbound session key for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.10.1.8 | ColumnipsecNewCfgManualPolicyOutAhSpi | read-create | current | The AH outbound SPI for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.10.1.9 | ColumnipsecNewCfgManualPolicyInEspEncKey | read-create | current | The Esp inbound cipher key for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.10.1.10 | ColumnipsecNewCfgManualPolicyInEspAuthKey | read-create | current | The Esp inbound authenticator key for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.10.1.11 | ColumnipsecNewCfgManualPolicyInEspSpi | read-create | current | The Esp inbound SPI for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.10.1.12 | ColumnipsecNewCfgManualPolicyOutEspEncKey | read-create | current | The Esp outbound cipher key for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.10.1.13 | ColumnipsecNewCfgManualPolicyOutEspAuthKey | read-create | current | The Esp outbound authenticator key for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.10.1.14 | ColumnipsecNewCfgManualPolicyOutEspSpi | read-create | current | The Esp outbound SPI for an IPsec policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.10.1.15 | ColumnipsecNewCfgManualPolicyDelete | read-write | current | Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.11 | TableipsecCurCfgIfTable | not-accessible | current | The table of interface IPsec policy configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.11.1 | RowipsecCurCfgIfEntry | not-accessible | current | The table of interface IPsec policy configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.11.1.1 | ColumnipsecCurCfgIfIndex | read-only | current | The identifier of a particular interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.11.1.2 | ColumnipsecCurCfgIfDynamicPolicyBmap | read-only | current | The IPsec dynamic policies applied to the IP interface. The policies are presented in bitmap format. This string displays policy number from 1 to 32. in receiv… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.11.1.5 | ColumnipsecCurCfgIfManualPolicyBmap | read-only | current | The manual policies applied to the IP interface. The policies are presented in bitmap format. This string displays policy number from 1 to 32. in receiving ord… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.11.1.8 | ColumnipsecCurCfgIfDelete | read-only | current | Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.12 | TableipsecNewCfgIfTable | not-accessible | current | The table of interface IPsec policy configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.12.1 | RowipsecNewCfgIfEntry | not-accessible | current | The table of interface IPsec policy configuration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.12.1.1 | ColumnipsecNewCfgIfIndex | read-only | current | The identifier of a particular interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.12.1.2 | ColumnipsecNewCfgIfDynamicPolicyBmap | read-only | current | The dynamic policies applied to the IP interface. The policies are presented in bitmap format. This string displays policy number from 1 to 32. in receiving or… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.12.1.3 | ColumnipsecNewCfgIfAddDynamicPolicy | read-create | current | Set the value to a IPsec dynamic policy ID when add the policy to IP interface. A value of 0 is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.12.1.4 | ColumnipsecNewCfgIfDelDynamicPolicy | read-create | current | Set the value to a IPsec dynamic policy ID when delete the policy to IP interface. A value of 0 is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.12.1.5 | ColumnipsecNewCfgIfManualPolicyBmap | read-only | current | The manual policies applied to the IP interface. The policies are presented in bitmap format. This string displays policy number from 1 to 32. in receiving ord… |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.12.1.6 | ColumnipsecNewCfgIfAddManualPolicy | read-create | current | Set the value to a IPsec manual policy ID when add the policy to IP interface. A value of 0 is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.12.1.7 | ColumnipsecNewCfgIfDelManualPolicy | read-create | current | Set the value to a IPsec manual policy ID when delete the policy to IP interface. A value of 0 is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.32.2.12.1.8 | ColumnipsecNewCfgIfDelete | read-write | current | Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33 | NodedhcpsnpCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.1 | ScalardhcpSnoopingCurCfgOnState | read-only | current | DHCP Snooping ON/OFF settings. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.2 | ScalardhcpSnoopingNewCfgOnState | read-write | current | DHCP Snooping ON/OFF setting. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.3 | ScalardhcpSnoopingCurCfgOption82OnState | read-only | current | on/off state of DHCP Snooping option82. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.4 | ScalardhcpSnoopingNewCfgOption82OnState | read-write | current | Enable/Disable DHCP Snooping option82 |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.5 | TabledhcpSnoopingCurCfgPortTable | not-accessible | current | DHCP Snooping Port Configuration Table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.5.1 | RowdhcpSnoopingCurCfgPortTableEntry | not-accessible | current | A row in DHCP Snooping Port Configuration Table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.5.1.1 | ColumndhcpSnoopingCurCfgPortId | read-only | current | Port ID of this DHCP Snooping port configration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.5.1.2 | ColumndhcpSnoopingCurCfgPortTrusted | read-only | current | Set port as trusted or untrusted port. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.5.1.3 | ColumndhcpSnoopingCurCfgPortRateLimit | read-only | current | Set port DHCP packet rate limit(pps). Its ranges is 0 ~ 2048, set 0 to disable rate limit. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.6 | TabledhcpSnoopingNewCfgPortTable | not-accessible | current | DHCP Snooping Port Configuration Table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.6.1 | RowdhcpSnoopingNewCfgPortTableEntry | not-accessible | current | A row in the DHCP Snooping Port Configuration Table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.6.1.1 | ColumndhcpSnoopingNewCfgportId | read-only | current | Port ID of this DHCP Snooping port configration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.6.1.2 | ColumndhcpSnoopingNewCfgportTrusted | read-write | current | Set port as trusted or untrusted port. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.6.1.3 | ColumndhcpSnoopingNewCfgportRateLimit | read-write | current | Set port DHCP packet rate limit(pps). Set 0 to disable rate limit. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.7 | TabledhcpSnoopingCurCfgVlanTable | not-accessible | current | DHCP Snooping VLAN Table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.7.1 | RowdhcpSnoopingCurCfgVlanTableEntry | not-accessible | current | A row in the DHCP Snooping VLAN Table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.7.1.1 | ColumndhcpSnoopingCurCfgVlanId | read-only | current | VLAN ID of this DHCP Snooping VLAN configration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.7.1.2 | ColumndhcpSnoopingCurCfgVlanOnState | read-only | current | on/off state of DHCP Snooping on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.8 | TabledhcpSnoopingNewCfgVlanTable | not-accessible | current | DHCP Snooping VLAN Table. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.8.1 | RowdhcpSnoopingNewCfgVlanTableEntry | not-accessible | current | A row in the DHCP Snooping VLAN Table |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.8.1.1 | ColumndhcpSnoopingNewCfgVlanId | read-only | current | VLAN ID of this DHCP Snooping VLAN configration. |
| 1.3.6.1.4.1.26543.2.7.7.3.1.33.8.1.2 | ColumndhcpSnoopingNewCfgVlanOnState | read-write | current | Enable/Disable DHCP Snooping on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.2 | Nodelayer3Stats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.2 | NodearpStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.2.1 | ScalararpStatEntries | read-only | current | The current number of ARP entries. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.2.2 | ScalararpStatHighWater | read-only | current | The highest number of ARP entries. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.2.3 | ScalararpStatMaxEntries | read-only | current | The maximum number of ARP entries. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.3 | NoderouteStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.3.1 | ScalarrouteStatEntries | read-only | current | The current number of IP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.3.2 | ScalarrouteStatHighWater | read-only | current | The highest number of IP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.3.3 | ScalarrouteStatStaticEntries | read-only | current | Current static routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.3.4 | ScalarrouteStatRipEntries | read-only | current | Current RIP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.3.5 | ScalarrouteStatOspfEntries | read-only | current | Current OSPF routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.3.6 | ScalarrouteStatBgpEntries | read-only | current | Current BGP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.3.7 | ScalarrouteStatMaxEntries | read-only | current | The maximum number of IP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.3.8 | ScalarrouteStatEcmpMaxEntries | read-only | current | Maximum number of ECMP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.3.9 | ScalarrouteStatEcmpMaxStaticEntries | read-only | current | Maximum number of static ECMP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.3.11 | ScalarrouteStatEcmpPathsEntries | read-only | current | Number of routes with ECMP paths. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.4 | NodednsStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.4.1 | ScalardnsStatInGoodDnsRequests | read-only | current | The total number of DNS request packets which are received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.4.2 | ScalardnsStatInBadDnsRequests | read-only | current | The total number of DNS request packets received that were dropped. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.4.3 | ScalardnsStatOutDnsRequests | read-only | current | The total number of DNS request packets that have been transmitted. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.5 | NodevrrpStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.5.1 | ScalarvrrpStatInAdvers | read-only | current | The number of good VRRP advertisements which are received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.5.2 | ScalarvrrpStatOutAdvers | read-only | current | The number of good VRRP advertisements which are transmitted. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.5.3 | ScalarvrrpStatBadAdvers | read-only | current | The number of bad VRRP advertisements which are received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.5.4 | ScalarvrrpStatBadVersion | read-only | current | The number of bad VRRP version adv which are received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.5.5 | ScalarvrrpStatBadAddress | read-only | current | The number of bad VRRP addres adv which are received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.5.6 | ScalarvrrpStatBadPassword | read-only | current | The number of bad VRRP advertisements which are received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.5.7 | ScalarvrrpStatBadVrid | read-only | current | The number of bad VRRP version ID adv which are received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.5.8 | ScalarvrrpStatBadData | read-only | current | The number of bad VRRP advertisements which are received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.5.9 | ScalarvrrpStatBadInterval | read-only | current | The number of bad VRRP intervals which are received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.5.10 | ScalarvrrpStatOutGratuitousARPs | read-only | current | The number of gratuitous ARP packets which are transmitted. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6 | NodeospfStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1 | NodeospfGeneralStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.1 | NodeospfCumRxTxStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.1.1 | ScalarospfCumRxPkts | read-only | current | The sum total of all OSPF packets received on all OSPF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.1.2 | ScalarospfCumTxPkts | read-only | current | The sum total of all OSPF packets transmitted on all OSPF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.1.3 | ScalarospfCumRxHello | read-only | current | The sum total of all Hello packets received on all OSPF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.1.4 | ScalarospfCumTxHello | read-only | current | The sum total of all Hello packets transmitted on all OSPF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.1.5 | ScalarospfCumRxDatabase | read-only | current | The sum total of all Database Description packets received on all OSPF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.1.6 | ScalarospfCumTxDatabase | read-only | current | The sum total of all Database Description packets transmitted on all OSPF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.1.7 | ScalarospfCumRxlsReqs | read-only | current | The sum total of all Link State Request packets received on all OSPF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.1.8 | ScalarospfCumTxlsReqs | read-only | current | The sum total of all Link State Request packets transmitted on all OSPF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.1.9 | ScalarospfCumRxlsAcks | read-only | current | The sum total of all Link State Acknowledgement packets received on all OSPF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.1.10 | ScalarospfCumTxlsAcks | read-only | current | The sum total of all Link State Acknowledgement packets transmitted on all OSPF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.1.11 | ScalarospfCumRxlsUpdates | read-only | current | The sum total of all Link State Update packets received on all OSPF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.1.12 | ScalarospfCumTxlsUpdates | read-only | current | The sum total of all Link State Update packets transmitted on all OSPF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.2 | NodeospfCumNbrChangeStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.2.1 | ScalarospfCumNbrhello | read-only | current | The sum total of all Hello packets received from neighbours on all OSPF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.2.2 | ScalarospfCumNbrStart | read-only | current | The sum total number of neighbours in this state (i.e. an indication that Hello packets should now be sent to the neighbour at intervals of HelloInterval secon… |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.2.3 | ScalarospfCumNbrAdjointOk | read-only | current | The sum total number of decisions to be made (again) as to whether an adjacency should be established/maintained with the neighbour across all OSPF areas and i… |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.2.4 | ScalarospfCumNbrNegotiationDone | read-only | current | The sum total number of neighbours in this state wherein the Master/slave relationship has been negotiated, and sequence numbers have been exchanged, across al… |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.2.5 | ScalarospfCumNbrExchangeDone | read-only | current | The sum total number of neighbours in this state (i.e. in an adjacency's final state) having transimitted a full sequence of Database Description packets, acro… |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.2.6 | ScalarospfCumNbrBadRequests | read-only | current | The sum total number of Link State Requests which have been received for a link state advertisement not contained in the database across all interfaces and OSP… |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.2.7 | ScalarospfCumNbrBadSequence | read-only | current | The sum total number of Database Description packets which have been received that either a) has an unexpected DD sequence number b) Unexpectedly has the init … |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.2.8 | ScalarospfCumNbrLoadingDone | read-only | current | The sum total number of link state updates received for all out-of-date portions of the database across all OSPF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.2.9 | ScalarospfCumNbrN1way | read-only | current | The sum total number of Hello packets received from neighbours, in which this router is not mentioned across all OSPF interfaces and areas. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.2.10 | ScalarospfCumNbrRstAd | read-only | current | The sum total number of times the Neighbour adjacency has been reset across all OPSF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.2.11 | ScalarospfCumNbrDown | read-only | current | The total number of Neighbouring routers down (i.e. in the initial state of a neighbour conversation.) across all OSPF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.2.12 | ScalarospfCumNbrN2way | read-only | current | The sum total number of Hello packets received from neighbours, in which this router is mentioned across all OSPF interfaces and areas. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.3 | NodeospfCumIntfChangeStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.3.1 | ScalarospfCumIntfHello | read-only | current | The sum total number of Hello packets sent on all interfaces and areas |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.3.2 | ScalarospfCumIntfDown | read-only | current | The sum total number of interfaces down in all OSPF areas. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.3.3 | ScalarospfCumIntfLoop | read-only | current | The sum total of interfaces no longer connected to the attatched network across all OSPF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.3.4 | ScalarospfCumIntfUnloop | read-only | current | The sum total number of interfaces, connected to the attatched network in all OSPF areas. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.3.5 | ScalarospfCumIntfWaitTimer | read-only | current | The sum total number of times the Wait Timer has been fired, (indicating the end of the waiting period that is required before electing a (Backup) Designated R… |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.3.6 | ScalarospfCumIntfBackup | read-only | current | The sum total number of Backup Designated Routers on the attatched network for all OSPF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.3.7 | ScalarospfCumIntfNbrChange | read-only | current | The sum total number of changes in the set of bidirectional neighbours associated with any interface across all OSPF areas. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.4 | NodeospfTimersKickOffStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.4.1 | ScalarospfTmrsKckOffHello | read-only | current | The sum total number of times the Hello timer has been fired (which triggers the send of a Hello packet) across all OPSF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.4.2 | ScalarospfTmrsKckOffRetransmit | read-only | current | The sum total number of times the Retransmit timer has been fired across all OPSF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.4.3 | ScalarospfTmrsKckOffLsaLock | read-only | current | The sum total number of times the Lsa Lock timer has been fired across all OSPF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.4.4 | ScalarospfTmrsKckOffLsaAck | read-only | current | The sum total number of times the Lsa Ack timer has been fired across all ospf areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.4.5 | ScalarospfTmrsKckOffDbage | read-only | current | The total number of times the Dbage has been fired. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.4.6 | ScalarospfTmrsKckOffSummary | read-only | current | The total number of times the Summary timer has been fired. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.1.4.7 | ScalarospfTmrsKckOffAseExport | read-only | current | The total number of times the ASE Export timer has been fired. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2 | NodeospfArea | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.1 | TableospfAreaRxTxStats | not-accessible | current | The table of OSPF Area Rx/Tx Statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.1.1 | RowospfAreaRxTxStatsEntry | not-accessible | current | Rx Tx packet Statistics about a OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.1.1.1 | ColumnospfAreaRxTxIndex | read-only | current | The index of the ospf Area for which these statistics apply. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.1.1.2 | ColumnospfAreaRxPkts | read-only | current | The total number of OSPF packets received in this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.1.1.3 | ColumnospfAreaTxPkts | read-only | current | The total number of OSPF packets transmitted in this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.1.1.4 | ColumnospfAreaRxHello | read-only | current | The total number of Hello packets received in this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.1.1.5 | ColumnospfAreaTxHello | read-only | current | The total number of Hello packets transmitted in this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.1.1.6 | ColumnospfAreaRxDatabase | read-only | current | The total number of Database Description packets transmitted for this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.1.1.7 | ColumnospfAreaTxDatabase | read-only | current | The total number of Database Description packets transmitted for this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.1.1.8 | ColumnospfAreaRxlsReqs | read-only | current | The total number of Link State Request packets received for this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.1.1.9 | ColumnospfAreaTxlsReqs | read-only | current | The total number of Link State Request packets transmitted for this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.1.1.10 | ColumnospfAreaRxlsAcks | read-only | current | The total number of Link State Acknowledgement packets received for this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.1.1.11 | ColumnospfAreaTxlsAcks | read-only | current | The total number of Link State Acknowledgement packets transmitted for this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.1.1.12 | ColumnospfAreaRxlsUpdates | read-only | current | The total number of Link State Update packets received for this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.1.1.13 | ColumnospfAreaTxlsUpdates | read-only | current | The total number of Link State Update packets transmitted for this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.2 | TableospfAreaNbrChangeStats | not-accessible | current | The table of OSPF Area Neighbour Statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.2.1 | RowospfAreaNbrChangeStatsEntry | not-accessible | current | Area Neighbour Change Statistics about a OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.2.1.1 | ColumnospfAreaNbrIndex | read-only | current | The index of the ospf Area for which these statistics apply. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.2.1.2 | ColumnospfAreaNbrhello | read-only | current | The total number of Hello packets received from neighbours in this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.2.1.3 | ColumnospfAreaNbrStart | read-only | current | The total number of neighbours in this state (i.e. an indication that Hello packets should now be sent to the neighbour at intervals of HelloInterval seconds.)… |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.2.1.4 | ColumnospfAreaNbrAdjointOk | read-only | current | The total number of decisions to be made (again) as to whether an adjacency should be established/maintained with the neighbour. for this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.2.1.5 | ColumnospfAreaNbrNegotiationDone | read-only | current | The total number of neighbours in this state wherein the Master/slave relationship has been negotiated, and sequence numbers have been exchanged, for this OSPF… |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.2.1.6 | ColumnospfAreaNbrExchangeDone | read-only | current | The total number of neighbours in this state (i.e. in an adjacency's final state) having transimitted a full sequence of Database Description packets, for this… |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.2.1.7 | ColumnospfAreaNbrBadRequests | read-only | current | The sum total number of Link State Requests which have been received for a link state advertisement not contained in the database across this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.2.1.8 | ColumnospfAreaNbrBadSequence | read-only | current | The total number of Database Description packets which have been received that either a) has an unexpected DD sequence number b) Unexpectedly has the init bit … |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.2.1.9 | ColumnospfAreaNbrLoadingDone | read-only | current | The total number of link state updates received for all out-of-date portions of the database in this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.2.1.10 | ColumnospfAreaNbrN1way | read-only | current | The total number of Hello packets received from neighbours, in which this router is not mentioned in this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.2.1.11 | ColumnospfAreaNbrRstAd | read-only | current | The total number of times the Neighbour adjacency has been reset across this OPSF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.2.1.12 | ColumnospfAreaNbrDown | read-only | current | The total number of Neighbouring routers down (i.e. in the initial state of a neighbour conversation.) in this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.2.1.13 | ColumnospfAreaNbrN2way | read-only | current | The total number of Hello packets received from neighbours, in which this router is mentioned in this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.3 | TableospfAreaChangeStats | not-accessible | current | The table of OSPF Area Change Statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.3.1 | RowospfAreaChangeStatsEntry | not-accessible | current | Area Change Statistics about a OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.3.1.1 | ColumnospfAreaIntfIndex | read-only | current | The index of the OSPF Area for which these statistics apply. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.3.1.2 | ColumnospfAreaIntfHello | read-only | current | The total number of Hello packets sent on this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.3.1.3 | ColumnospfAreaIntfDown | read-only | current | The total number of interfaces down in this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.3.1.4 | ColumnospfAreaIntfLoop | read-only | current | The total number of interfaces no longer connected to the attatched network in this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.3.1.5 | ColumnospfAreaIntfUnloop | read-only | current | The total number of interfaces connected to the attatched network in this OSPF area.. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.3.1.6 | ColumnospfAreaIntfWaitTimer | read-only | current | The total number of times the Wait Timer has been fired, (indicating the end of the waiting period that is required before electing a (Backup) Designated Route… |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.3.1.7 | ColumnospfAreaIntfBackup | read-only | current | The total number of Backup Designated Routers on the attatched network for this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.3.1.8 | ColumnospfAreaIntfNbrChange | read-only | current | The total number of changes in the set of bidirectional neighbours associated with the interface in this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.4 | TableospfAreaErrorStats | not-accessible | current | The table of OSPF Area Error Statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.4.1 | RowospfAreaErrorStatsEntry | not-accessible | current | Error Statistics for an OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.4.1.1 | ColumnospfAreaErrIndex | read-only | current | The index of the OSPF Area for which these statistics apply. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.4.1.2 | ColumnospfAreaErrAuthFailure | read-only | current | The total number of packets received with a wrong password in this area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.4.1.3 | ColumnospfAreaErrNetmaskMismatch | read-only | current | The total number of packets received with a wrong netmask in this area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.4.1.4 | ColumnospfAreaErrHelloMismatch | read-only | current | The total number of packets received with a different hello interval in this area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.4.1.5 | ColumnospfAreaErrDeadMismatch | read-only | current | The total number of packets received with a different dead interval in this area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.4.1.6 | ColumnospfAreaErrOptionsMismatch | read-only | current | The total number of packets received with a different options in this area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.4.1.7 | ColumnospfAreaErrUnknownNbr | read-only | current | The total number of packets received from an unknown neighbor in this area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.4.1.8 | ColumnospfAreaErrAreaMismatch | read-only | current | The total number of packets received with a wrong area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.2.4.1.9 | ColumnospfAreaErrInvalidSelfOrigLsa | read-only | current | The total number of packets received with invalid self originated LSAs. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3 | NodeospfInterface | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.1 | TableospfIntfRxTxStats | not-accessible | current | The table of OSPF Interface Rx/Tx packet Statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.1.1 | RowospfIntfRxTxStatsEntry | not-accessible | current | OSPF interface Rx/Tx packet statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.1.1.1 | ColumnospfIntfRxTxIndex | read-only | current | The OSPF interface for which these statistics apply. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.1.1.2 | ColumnospfIntfRxPkts | read-only | current | The total number of OSPF packets received for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.1.1.3 | ColumnospfIntfTxPkts | read-only | current | The total number of OSPF packets transmitted for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.1.1.4 | ColumnospfIntfRxHello | read-only | current | The total number of Hello packets received for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.1.1.5 | ColumnospfIntfTxHello | read-only | current | The total number of Hello packets transmitted for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.1.1.6 | ColumnospfIntfRxDatabase | read-only | current | The total number of Database Description packets received for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.1.1.7 | ColumnospfIntfTxDatabase | read-only | current | The total number of Database Description packets transmitted for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.1.1.8 | ColumnospfIntfRxlsReqs | read-only | current | The total number of Link State Request packets received for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.1.1.9 | ColumnospfIntfTxlsReqs | read-only | current | The total number of Link State Request packets transmitted for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.1.1.10 | ColumnospfIntfRxlsAcks | read-only | current | The total number of Link State Acknowledgement packets received for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.1.1.11 | ColumnospfIntfTxlsAcks | read-only | current | The total number of Link State Acknowledgement packets transmitted for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.1.1.12 | ColumnospfIntfRxlsUpdates | read-only | current | The total number of Link State Update packets received for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.1.1.13 | ColumnospfIntfTxlsUpdates | read-only | current | The total number of Link State Update packets transmitted for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.2 | TableospfIntfNbrChangeStats | not-accessible | current | The table of OSPF Interface Neighbour change Statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.2.1 | RowospfIntfNbrChangeStatsEntry | not-accessible | current | OSPF interface Neighbour Change statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.2.1.1 | ColumnospfIntfNbrIndex | read-only | current | The index of the OSPF Interface for which these statistics apply. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.2.1.2 | ColumnospfIntfNbrhello | read-only | current | The total number of Hello packets received from neighbours in this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.2.1.3 | ColumnospfIntfNbrStart | read-only | current | The total number of neighbours in this state (i.e. an indication that Hello packets should now be sent to the neighbour at intervals of HelloInterval seconds.)… |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.2.1.4 | ColumnospfIntfNbrAdjointOk | read-only | current | The total number of decisions to be made (again) as to whether an adjacency should be established/maintained with the neighbour. for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.2.1.5 | ColumnospfIntfNbrNegotiationDone | read-only | current | The total number of neighbours in this state wherein the Master/slave relationship has been negotiated, and sequence numbers have been exchanged, for this OSPF… |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.2.1.6 | ColumnospfIntfNbrExchangeDone | read-only | current | The total number of neighbours in this state (i.e. in an adjacency's final state) having transimitted a full sequence of Database Description packets, for this… |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.2.1.7 | ColumnospfIntfNbrBadRequests | read-only | current | The total number of Link State Requests which have been received for a link state advertisement not contained in the database for this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.2.1.8 | ColumnospfIntfNbrBadSequence | read-only | current | The total number of Database Description packets which have been received that either a) has an unexpected DD sequence number b) Unexpectedly has the init bit … |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.2.1.9 | ColumnospfIntfNbrLoadingDone | read-only | current | The total number of link state updates received for all out-of-date portions of the database for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.2.1.10 | ColumnospfIntfNbrN1way | read-only | current | The total number of Hello packets received from neighbours, in which this router is not mentioned for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.2.1.11 | ColumnospfIntfNbrRstAd | read-only | current | The sum total number of times the Neighbour adjacency has been reset on this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.2.1.12 | ColumnospfIntfNbrDown | read-only | current | The total number of Neighbouring routers down (i.e. in the initial state of a neighbour conversation.) for this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.2.1.13 | ColumnospfIntfNbrN2way | read-only | current | The total number of Hello packets received from neighbours, in which this router is mentioned for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.3 | TableospfIntfChangeStats | not-accessible | current | The table of OSPF Interface change Statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.3.1 | RowospfIntfChangeStatsEntry | not-accessible | current | OSPF interface Change statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.3.1.1 | ColumnospfIntfIndex | read-only | current | The index of the OSPF Interface for which these statistics apply. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.3.1.2 | ColumnospfIntfHello | read-only | current | The total number of Hello packets sent by this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.3.1.3 | ColumnospfIntfDown | read-only | current | The total number of times the interface was down. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.3.1.4 | ColumnospfIntfLoop | read-only | current | The total number of times the interface was no longer connected to the attatched network. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.3.1.5 | ColumnospfIntfUnloop | read-only | current | The total number of times the interface, connected back to the attatched network. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.3.1.6 | ColumnospfIntfWaitTimer | read-only | current | The total number of times the Wait Timer has been fired, (indicating the end of the waiting period that is required before electing a (Backup) Designated Route… |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.3.1.7 | ColumnospfIntfBackup | read-only | current | The total number of Backup Designated Routers on the attatched network for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.3.1.8 | ColumnospfIntfNbrChange | read-only | current | The total number of changes in the set of bidirectional neighbours associated with the interface for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.4 | TableospfIntfErrorStats | not-accessible | current | The table of OSPF Interface Error Statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.4.1 | RowospfIntfErrorStatsEntry | not-accessible | current | Error Statistics for an OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.4.1.1 | ColumnospfIntfErrIndex | read-only | current | The index of the OSPF Intf for which these statistics apply. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.4.1.2 | ColumnospfIntfErrAuthFailure | read-only | current | The total number of packets received with a wrong password in this area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.4.1.3 | ColumnospfIntfErrNetmaskMismatch | read-only | current | The total number of packets received with a wrong netmask in this area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.4.1.4 | ColumnospfIntfErrHelloMismatch | read-only | current | The total number of packets received with a different hello interval in this area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.4.1.5 | ColumnospfIntfErrDeadMismatch | read-only | current | The total number of packets received with a different dead interval in this area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.4.1.6 | ColumnospfIntfErrOptionsMismatch | read-only | current | The total number of packets received with a different options in this area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.4.1.7 | ColumnospfIntfErrUnknownNbr | read-only | current | The total number of packets received from an unknown neighbor in this area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.4.1.8 | ColumnospfIntfErrAreaMismatch | read-only | current | The total number of packets received with a wrong area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.6.3.4.1.9 | ColumnospfIntfErrInvalidSelfOrigLSA | read-only | current | The total number of packets received with invalid self-orig LSAs. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.7 | NodeclearStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.7.1 | ScalaripClearStats | read-write | current | Setting this to clear(2) results in clearing the IP statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.7.2 | ScalarvrrpClearStats | read-write | current | Setting this to clear(2) results in clearing the VRRP statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.7.4 | ScalarospfClearStats | read-write | current | Setting this to clear(1) results in clearing the OSPF statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.7.5 | ScalartcpClearStats | read-write | current | Setting this to clear(1) results in clearing the TCP statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.7.6 | ScalarudpClearStats | read-write | current | Setting this to clear(1) results in clearing the UDP statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.7.7 | ScalardnsClearStats | read-write | current | Setting this to clear(1) results in clearing the DNS statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.7.8 | ScalararpClearStats | read-write | current | Setting this to clear(1) results in clearing the ARP statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.7.9 | ScalaricmpClearStats | read-write | current | Setting this to clear(1) results in clearing the ICMP statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.7.10 | ScalarrouteClearStats | read-write | current | Setting this to clear(1) results in clearing the Route statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.7.13 | Scalaripv6ClearStats | read-write | current | Setting this to clear(1) results in clearing the IPv6 statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.7.14 | Scalaripv6ClearIcmpStats | read-write | current | Setting this to clear(1) results in clearing the ICMP6 statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.7.15 | Scalaripv6ClearUdpStats | read-write | current | Setting this to clear(1) results in clearing the UDP6 statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.7.16 | Scalarospf3ClearStats | read-write | current | Setting this to clear(1) results in clearing the ospf3 statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.7.17 | ScalarripClearStats | read-write | current | Setting this to clear(1) results in clearing the RIP statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.7.18 | Scalaripv6NbrClearStats | read-write | current | Setting this to clear(1) results in clearing the IPv6 nbr statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9 | NodeigmpStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1 | TableigmpSnoopStats | not-accessible | current | Statistics for IGMP Snooping. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1.1 | RowigmpSnoopStatsEntry | not-accessible | current | Statistics for IGMP Snooping. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1.1.1 | ColumnigmpSnoopVlanIndex | read-only | current | The index of the VLAN for which these statistics apply. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1.1.2 | ColumnrxIgmpValidPkts | read-only | current | The total number of valid IGMP packets received on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1.1.3 | ColumnrxIgmpInvalidPkts | read-only | current | The total number of invalid IGMP packets received on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1.1.4 | ColumnrxIgmpGenQueries | read-only | current | The total number of IGMP General Query packets received on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1.1.5 | ColumnrxIgmpGrpSpecificQueries | read-only | current | The total number of IGMP Group Specific Query packets received on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1.1.6 | ColumnrxIgmpLeaves | read-only | current | The total number of IGMP Leave packets received on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1.1.7 | ColumnrxIgmpReports | read-only | current | The total number of IGMP Report packets received on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1.1.8 | ColumntxIgmpGrpSpecificQueries | read-only | current | The total number of IGMP Group Specific Query packets transmitted on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1.1.9 | ColumntxIgmpReports | read-only | current | The total number of IGMP Report packets transmitted on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1.1.10 | ColumntxIgmpLeaves | read-only | current | The total number of IGMP Leave packets transmitted on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1.1.11 | ColumnrxIgmpGroupSourceSpecificQueries | read-only | current | The total number of IGMP Group Source Specific (GSSQ) Queries received on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1.1.12 | ColumnrxIgmpV3CurrentStateRecords | read-only | current | The total number of IGMP Current State Records (CSRs) received on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1.1.13 | ColumnrxIgmpV3SourceListChangeRecords | read-only | current | The total number of IGMP Source List Change Records (SLCRs) received on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1.1.14 | ColumnrxIgmpV3FilterChangeRecords | read-only | current | The total number of IGMP Filter Mode Change Records (FMCRs) received on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1.1.16 | ColumntxIgmpGenQueries | read-only | current | The total number of IGMP General Query packets send on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1.1.17 | ColumnrxIgmpDiscardPkts | read-only | current | The total number of IGMP packets discarded on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1.1.18 | ColumnrxIgmpPimHellos | read-only | current | The total number of Pim Hello packets received on this VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.1.1.19 | ColumnigmpClearVlanStats | read-write | current | Setting this to clear(1) results in clearing the statistics for this snooping VLAN. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.2 | ScalarigmpClearAllStats | read-write | current | Setting this to clear(1) results in clearing the IGMP statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.3 | ScalarigmpStatsTotalIgmpGroups | read-only | current | The total number of IGMP groups. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.9.4 | ScalarigmpStatsTotalIpmcGroups | read-only | current | The total number of IPMC groups. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10 | Nodeipv6Stats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.1 | Scalaripv6InReceives | read-only | current | The total number of input datagrams received from interfaces, including those received in error. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.2 | Scalaripv6InMcasts | read-only | current | The total number of multicast packets received from interfaces, including those received in error. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.3 | Scalaripv6InDelivers | read-only | current | Total datagrams given to upper layer - ICMP/UDP |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.4 | Scalaripv6InDiscards | read-only | current | Total datagrams discarded despite no errors |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.5 | Scalaripv6InHdrerrs | read-only | current | Total datagrams with error in IPv6/Option headers |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.6 | Scalaripv6InAddrerrs | read-only | current | Total datagrams with error in destination address |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.7 | Scalaripv6InUnkprots | read-only | current | Total datagrams with unknown/unsupported protocol |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.8 | Scalaripv6InTruncs | read-only | current | Total datagrams with insufficient data |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.10 | Scalaripv6OutMcasts | read-only | current | Total sent multicast pkts |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.11 | Scalaripv6ForwDgrams | read-only | current | Total datagrams attempted to be forwarded |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.12 | Scalaripv6TooBigerrs | read-only | current | Total datagrams which could not be forwarded as their size exceeds (Path) MTU |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.13 | Scalaripv6OutReqs | read-only | current | Total datagrams attempted to be sent |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.14 | Scalaripv6OutDiscards | read-only | current | Total outgoing Datagrams discarded despite no errors |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.15 | Scalaripv6OutNorts | read-only | current | Total datagrams discarded due to no routes |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.16 | Scalaripv6Reasmreqs | read-only | current | Total datagrams needing reassembly |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.17 | Scalaripv6Reasmoks | read-only | current | Total datagrams successfully reassembled |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.18 | Scalaripv6Reasmfails | read-only | current | Total datagrams for witch reassembly failured |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.19 | Scalaripv6Fragoks | read-only | current | Total datagrams successfully fragmented |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.20 | Scalaripv6Fragfails | read-only | current | Total datagrams for witch fragmentation failured |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.21 | Scalaripv6Fragcreates | read-only | current | Total number of fragments created |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.22 | Scalaripv6InNsols | read-only | current | Total number of received Neighbor Solicitations |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.23 | Scalaripv6InNadvs | read-only | current | Total number of received Neighbor Advertisements |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.25 | Scalaripv6InRoutsols | read-only | current | Total number of received Router Solicitations |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.26 | Scalaripv6InRoutadvs | read-only | current | Total number of received Router Advertisements |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.27 | Scalaripv6InRoutRedirs | read-only | current | Total number of received Router Redirect messages |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.28 | Scalaripv6OutNsols | read-only | current | Total number of sent Neighbor Solicitations |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.29 | Scalaripv6OutNadvs | read-only | current | Total number of sent Neighbor Advertisements |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.30 | Scalaripv6OutRoutadvs | read-only | current | Total number of sent Router Advertisements |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.31 | Scalaripv6OutRedirs | read-only | current | Total number of sent Redirects |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.32 | Scalaripv6OutRoutSols | read-only | current | Total number of sent Router Solicitations |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.39 | Scalaripv6icmpInMsgs | read-only | current | The total number of ICMP messages received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.40 | Scalaripv6icmpInErrs | read-only | current | The total number of ICMP messages attempted to send. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.41 | Scalaripv6icmpInBadcode | read-only | current | The total number of ICMP messages in bad code. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.42 | Scalaripv6icmpInToobig | read-only | current | The number of ICMP too big messages received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.43 | Scalaripv6icmpInDstUnreach | read-only | current | The number of ICMP Destination Unreachable messages received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.44 | Scalaripv6icmpInTmexceeded | read-only | current | The number of ICMP Time Exceeded messages received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.45 | Scalaripv6icmpInParamprob | read-only | current | The number of ICMP Parameter Problem messages received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.46 | Scalaripv6icmpInEchoReq | read-only | current | The number of ICMP Echo request messages received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.47 | Scalaripv6icmpInEchoResp | read-only | current | The number of ICMP Echo Reply messages received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.48 | Scalaripv6icmpOutMsgs | read-only | current | The total number of ICMP messages which this entity attempted to send. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.49 | Scalaripv6icmpOutErrs | read-only | current | The number of ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.50 | Scalaripv6icmpOutDstUnreach | read-only | current | The number of ICMP Destination Unreachable messages sent. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.51 | Scalaripv6icmpOutToobig | read-only | current | The number of ICMP too big messages sent. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.52 | Scalaripv6icmpOutTmexceeded | read-only | current | The number of ICMP Time Exceeded messages sent. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.53 | Scalaripv6icmpOutParamprob | read-only | current | The number of ICMP Parameter Problem messages sent. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.54 | Scalaripv6icmpOutEchoReq | read-only | current | The number of ICMP Echo request messages sent. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.55 | Scalaripv6icmpOutEchoResp | read-only | current | The number of ICMP Echo Reply messages sent. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.56 | Scalaripv6icmpInRouterSol | read-only | current | The number of ICMP router solicitations received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.57 | Scalaripv6icmpInRouterAdv | read-only | current | The number of ICMP router advertisements received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.58 | Scalaripv6icmpInNeighSol | read-only | current | The number of ICMP neighbor solicitations received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.59 | Scalaripv6icmpInNeighAdv | read-only | current | The number of ICMP neighbor advertisements received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.60 | Scalaripv6icmpInRedir | read-only | current | The number of ICMP Redirect messages received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.61 | Scalaripv6icmpOutRouterSol | read-only | current | The number of ICMP router solicitations sent. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.62 | Scalaripv6icmpOutRouterAdv | read-only | current | The number of ICMP router advertisements sent. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.63 | Scalaripv6icmpOutNeighSol | read-only | current | The number of ICMP neighbor solicitations sent. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.64 | Scalaripv6icmpOutNeighAdv | read-only | current | The number of ICMP neighbor advertisements sent. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.65 | Scalaripv6icmpOutRedir | read-only | current | The number of ICMP Redirect messages sent. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.66 | Scalaripv6udpInDgrams | read-only | current | Total number of UDP received datagrams. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.67 | Scalaripv6udpInErrs | read-only | current | Total number of UDP error encountered during processing of packet. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.68 | Scalaripv6udpOutDgrams | read-only | current | Total number of UDP datagrams passed to IP6 layer. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.69 | Scalaripv6udpNumPorts | read-only | current | Total number of UDP ports that are currently open. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.70 | Scalaripv6icmpInAdminProhib | read-only | current | The total number of received Destination Unreachable ICMP packets. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.10.71 | Scalaripv6icmpOutAdminProhib | read-only | current | The total number of sent Destination Unreachable ICMP packets. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.13 | Noderip2Stats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.13.1 | ScalarripStatInPackets | read-only | current | The total number of RIP packets received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.13.2 | ScalarripStatOutPackets | read-only | current | The total number of RIP packets transmitted. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.13.3 | ScalarripStatInRequestPkts | read-only | current | The total number of RIP requests received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.13.4 | ScalarripStatInResponsePkts | read-only | current | The total number of RIP response received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.13.5 | ScalarripStatOutRequestPkts | read-only | current | The total number of RIP requests transmitted. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.13.6 | ScalarripStatOutResponsePkts | read-only | current | The total number of RIP responses transmitted. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.13.7 | ScalarripStatRouteTimeout | read-only | current | The total number of RIP route timeouts. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.13.8 | ScalarripStatInBadSizePkts | read-only | current | The total number of bad size RIP packets received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.13.9 | ScalarripStatInBadVersion | read-only | current | The total number of RIP bad versions received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.13.10 | ScalarripStatInBadZeros | read-only | current | The total number of RIP bad zeros received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.13.11 | ScalarripStatInBadSourcePort | read-only | current | The total number of RIP bad source port received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.13.12 | ScalarripStatInBadSourceIP | read-only | current | The total number of RIP bad source IP received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.13.13 | ScalarripStatInSelfRcvPkts | read-only | current | The total number of RIP packets from self received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.16 | NodeipStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.16.1 | ScalaripStatsInReceives | read-only | current | ip InReceive |
| 1.3.6.1.4.1.26543.2.7.7.3.2.16.2 | ScalaripStatsInHdrErrors | read-only | current | ip InHdrError |
| 1.3.6.1.4.1.26543.2.7.7.3.2.16.3 | ScalaripStatsInAddrErrors | read-only | current | ip InAddrErrors |
| 1.3.6.1.4.1.26543.2.7.7.3.2.16.5 | ScalaripStatsInUnknownProtos | read-only | current | ip InUnknownProtos |
| 1.3.6.1.4.1.26543.2.7.7.3.2.16.6 | ScalaripStatsInDiscards | read-only | current | ip InDiscards |
| 1.3.6.1.4.1.26543.2.7.7.3.2.16.7 | ScalaripStatsInDelivers | read-only | current | ip InDelivers |
| 1.3.6.1.4.1.26543.2.7.7.3.2.16.8 | ScalaripStatsOutRequests | read-only | current | ip OutRequests |
| 1.3.6.1.4.1.26543.2.7.7.3.2.16.9 | ScalaripStatsOutDiscards | read-only | current | ip OutDiscards |
| 1.3.6.1.4.1.26543.2.7.7.3.2.16.19 | ScalaripStatsDefaultTTL | read-only | current | ip DefaultTTL |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17 | NodeicmpStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.1 | ScalaricmpStatsInMsgs | read-only | current | icmp InMsgs |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.2 | ScalaricmpStatsInErrors | read-only | current | icmp InErrors |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.3 | ScalaricmpStatsInDestUnreachs | read-only | current | icmp InDestUnreachs |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.4 | ScalaricmpStatsInTimeExcds | read-only | current | icmp InTimeExcds |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.5 | ScalaricmpStatsInParmProbs | read-only | current | icmp InParmProbs |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.6 | ScalaricmpStatsInSrcQuenchs | read-only | current | icmp InSrcQuenchs |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.7 | ScalaricmpStatsInRedirects | read-only | current | icmp InRedirects |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.8 | ScalaricmpStatsInEchos | read-only | current | icmp InEchos |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.9 | ScalaricmpStatsInEchoReps | read-only | current | icmp InEchoReps |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.10 | ScalaricmpStatsInTimestamps | read-only | current | icmp InTimestamps |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.11 | ScalaricmpStatsInTimestampReps | read-only | current | icmp InTimestampReps |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.12 | ScalaricmpStatsInAddrMasks | read-only | current | icmp InAddrMasks |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.13 | ScalaricmpStatsInAddrMaskReps | read-only | current | icmp InAddrMaskReps |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.14 | ScalaricmpStatsOutMsgs | read-only | current | icmp OutMsgs |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.15 | ScalaricmpStatsOutErrors | read-only | current | icmp OutErrors |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.16 | ScalaricmpStatsOutDestUnreachs | read-only | current | icmp OutDestUnreachs |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.17 | ScalaricmpStatsOutTimeExcds | read-only | current | icmp OutTimeExcds |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.18 | ScalaricmpStatsOutParmProbs | read-only | current | icmp OutParmProbs |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.19 | ScalaricmpStatsOutSrcQuenchs | read-only | current | icmp OutSrcQuenchs |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.20 | ScalaricmpStatsOutRedirects | read-only | current | icmp OutRedirects |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.21 | ScalaricmpStatsOutEchos | read-only | current | icmp OutEchos |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.22 | ScalaricmpStatsOutEchoReps | read-only | current | icmp OutEchoReps |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.23 | ScalaricmpStatsOutTimestamps | read-only | current | icmp OutTimestamps |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.24 | ScalaricmpStatsOutTimestampReps | read-only | current | icmp OutTimestampReps |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.25 | ScalaricmpStatsOutAddrMasks | read-only | current | icmp OutAddrMasks |
| 1.3.6.1.4.1.26543.2.7.7.3.2.17.26 | ScalaricmpStatsOutAddrMaskReps | read-only | current | icmp OutAddrMaskReps |
| 1.3.6.1.4.1.26543.2.7.7.3.2.18 | NodetcpStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.18.1 | ScalartcpStatsRtoAlgorithm | read-only | current | tcp RtoAlgorithm |
| 1.3.6.1.4.1.26543.2.7.7.3.2.18.2 | ScalartcpStatsRtoMin | read-only | current | tcp RtoMin |
| 1.3.6.1.4.1.26543.2.7.7.3.2.18.3 | ScalartcpStatsRtoMax | read-only | current | tcp RtoMax |
| 1.3.6.1.4.1.26543.2.7.7.3.2.18.4 | ScalartcpStatsMaxConn | read-only | current | tcp MaxConn |
| 1.3.6.1.4.1.26543.2.7.7.3.2.18.5 | ScalartcpStatsActiveOpens | read-only | current | tcp ActiveOpens |
| 1.3.6.1.4.1.26543.2.7.7.3.2.18.6 | ScalartcpStatsPassiveOpens | read-only | current | tcp PassiveOpens |
| 1.3.6.1.4.1.26543.2.7.7.3.2.18.7 | ScalartcpStatsAttemptFails | read-only | current | tcp AttemptFails |
| 1.3.6.1.4.1.26543.2.7.7.3.2.18.8 | ScalartcpStatsEstabResets | read-only | current | tcp EstabResets |
| 1.3.6.1.4.1.26543.2.7.7.3.2.18.9 | ScalartcpStatsInSegs | read-only | current | tcp InSegs |
| 1.3.6.1.4.1.26543.2.7.7.3.2.18.10 | ScalartcpStatsOutSegs | read-only | current | tcp OutSegs |
| 1.3.6.1.4.1.26543.2.7.7.3.2.18.11 | ScalartcpStatsRetransSegs | read-only | current | tcp RetransSegs |
| 1.3.6.1.4.1.26543.2.7.7.3.2.18.12 | ScalartcpStatsInErrs | read-only | current | tcp InErrs |
| 1.3.6.1.4.1.26543.2.7.7.3.2.18.13 | ScalartcpStatsCurrEstab | read-only | current | tcp CurrEstab |
| 1.3.6.1.4.1.26543.2.7.7.3.2.18.14 | ScalartcpStatsCurrConn | read-only | current | tcp CurrConn |
| 1.3.6.1.4.1.26543.2.7.7.3.2.18.15 | ScalartcpStatsOutRsts | read-only | current | tcp OutRsts |
| 1.3.6.1.4.1.26543.2.7.7.3.2.19 | NodeudpStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.19.1 | ScalarudpStatsInDatagrams | read-only | current | udp InDatagrams |
| 1.3.6.1.4.1.26543.2.7.7.3.2.19.2 | ScalarudpStatsOutDatagrams | read-only | current | udp OutDatagrams |
| 1.3.6.1.4.1.26543.2.7.7.3.2.19.3 | ScalarudpStatsInErrors | read-only | current | udp InErrors |
| 1.3.6.1.4.1.26543.2.7.7.3.2.19.4 | ScalarudpStatsNoPorts | read-only | current | udp NoPorts |
| 1.3.6.1.4.1.26543.2.7.7.3.2.20 | NodebootpStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.20.1 | TablebootpRelayStatsTable | not-accessible | current | The BOOTP relay agent statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.20.1.1 | RowbootpRelayStatsTableEntry | not-accessible | current | A row in the BOOTP relay agent statistics table. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.20.1.1.1 | ColumnbootpRelayStatsIndex | read-only | current | The port number of the port associated with this BOOTP relay statistics entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.20.1.1.2 | ColumnbootpRelayStatsRequestsReceived | read-only | current | The total number of BOOTP request packets received on the port. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.20.1.1.3 | ColumnbootpRelayStatsRequestsRelayed | read-only | current | The number of request packets relayed to the BOOTP server. If there is more than one server, a request is relayed once for each server; hence, with two servers… |
| 1.3.6.1.4.1.26543.2.7.7.3.2.20.1.1.5 | ColumnbootpRelayStatsRequestsDroppedNoRelay | read-only | current | This counter increases each time a request could not be relayed because BOOTP relay is disabled or not allowed on the port. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.20.1.1.6 | ColumnbootpRelayStatsRequestsDroppedNoServer | read-only | current | This counter increases each time a request is dropped because there is no configured server or the server is unreachable because there is no active IP interfac… |
| 1.3.6.1.4.1.26543.2.7.7.3.2.20.1.1.7 | ColumnbootpRelayStatsRequestsDroppedError | read-only | current | This counter increases each time a request is dropped due to various errors encountered while processing the request packet. Such errors include short packet l… |
| 1.3.6.1.4.1.26543.2.7.7.3.2.20.1.1.8 | ColumnbootpRelayStatsRepliesReceived | read-only | current | This is the total number of BOOTP response packets received on the port associated with this object. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.20.1.1.9 | ColumnbootpRelayStatsRepliesRelayed | read-only | current | This is the total number of response packets that were relayed to the client. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.20.1.1.10 | ColumnbootpRelayStatsRepliesDroppedError | read-only | current | This counter increases each time a response packet is dropped due to various errors encountered while processing the packet. Errors include unknown relay agent… |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22 | Nodeospf3Stats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1 | Nodeospf3GeneralStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.1 | Nodeospf3CumRxTxDisdStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.1.1 | Scalarospf3CumRxPkts | read-only | current | The total number of Ospf3 packets received on all of the router's interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.1.2 | Scalarospf3CumTxPkts | read-only | current | The total number of Ospf3 packets transmitted on all of the router's interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.1.3 | Scalarospf3CumDisdPkts | read-only | current | The total number of Ospf3 packets discaded on all of the router's interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.1.4 | Scalarospf3CumRxHello | read-only | current | The total number of Hello packets received on all of the router's interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.1.5 | Scalarospf3CumTxHello | read-only | current | The total number of Hello packets transmitted on all of the router's interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.1.6 | Scalarospf3CumDisdHello | read-only | current | The total number of Hello packets discaded on all of the router's interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.1.7 | Scalarospf3CumRxDatabase | read-only | current | The total number of Database Description packets received on all of the router's interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.1.8 | Scalarospf3CumTxDatabase | read-only | current | The total number of Database Description packets transmitted on all of the router's interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.1.9 | Scalarospf3CumDisdDatabase | read-only | current | The total number of Database Description packets discarded on all of the router's interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.1.10 | Scalarospf3CumRxlsReqs | read-only | current | The total number of Link State Request packets received on all of the router's interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.1.11 | Scalarospf3CumTxlsReqs | read-only | current | The total number of Link State Request packets transmitted on all of the router's interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.1.12 | Scalarospf3CumDisdlsReqs | read-only | current | The total number of Link State Request packets discarded on all of the router's interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.1.13 | Scalarospf3CumRxlsAcks | read-only | current | The total number of Link State Acknowledgement packets received on all of the router's interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.1.14 | Scalarospf3CumTxlsAcks | read-only | current | The total number of Link State Acknowledgement packets transmitted on all of the router's interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.1.15 | Scalarospf3CumDisdlsAcks | read-only | current | The total number of Link State Acknowledgement packets discarded on all of the router's interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.1.16 | Scalarospf3CumRxlsUpdates | read-only | current | The total number of Link State Update packets received on all of the router's interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.1.17 | Scalarospf3CumTxlsUpdates | read-only | current | The total number of Link State Update packets transmitted on all of the router's interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.1.18 | Scalarospf3CumDisdlsUpdates | read-only | current | The total number of Link State Update packets discarded on all of the router's interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.2 | Nodeospf3CumNbrChangeStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.2.1 | Scalarospf3CumNbrDown | read-only | current | The total number of times neighbors now existing on the interfaces now present on the router have changed into DOWN state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.2.2 | Scalarospf3CumNbrAttempt | read-only | current | The total number of times neighbors now existing the on interfaces now present on the router have changed into ATTEMPT state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.2.3 | Scalarospf3CumNbrInit | read-only | current | The total number of times neighbors now existing the on interfaces now present on the router have changed into INIT state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.2.4 | Scalarospf3CumNbrN2way | read-only | current | The total number of times neighbors now existing the on interfaces now present on the router have changed into 2WAY state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.2.5 | Scalarospf3CumNbrExStart | read-only | current | The total number of times neighbors now existing the on interfaces now present on the router have changed into EXSTART state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.2.6 | Scalarospf3CumNbrExchange | read-only | current | The total number of times neighbors now existing the on interfaces now present on the router have changed into EXCHANGE state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.2.7 | Scalarospf3CumNbrLoading | read-only | current | The total number of times neighbors now existing the on interfaces now present on the router have changed into LOADING state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.2.8 | Scalarospf3CumNbrFull | read-only | current | The total number of times neighbors now existing the on interfaces now present on the router have changed into FULL state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.2.9 | Scalarospf3CumNbrAllEvents | read-only | current | The total number of times neighbors now existing the on interfaces now present on the router have changed state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.3 | Nodeospf3CumIntfChangeStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.3.1 | Scalarospf3CumIntfDown | read-only | current | The total number of times, for all the interfaces on the router, an interface was down. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.3.2 | Scalarospf3CumIntfLoop | read-only | current | The total number of times , for all the interfaces on the router, an interface changed State into the LOOP State. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.3.3 | Scalarospf3CumIntfWaiting | read-only | current | The total number of times , for all the interfaces on the router, an interface changed State into the WAITING State. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.3.4 | Scalarospf3CumIntfPtop | read-only | current | The total number of times , for all the interfaces on the router, an interface changed State into the PTOP State. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.3.5 | Scalarospf3CumIntfDr | read-only | current | The total number of times , for all the interfaces on the router, an interface changed State into the DR State. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.3.6 | Scalarospf3CumIntfBackup | read-only | current | The total number of times , for all the interfaces on the router, an interface changed State into the BACKUP State. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.3.7 | Scalarospf3CumIntfDrOther | read-only | current | The total number of times , for all the interfaces on the router, an interface changed State into the DROTHER State. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.3.8 | Scalarospf3CumIntfAllEvents | read-only | current | The total number of times , for all the interfaces on the router, an interface changed it's state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.4 | Nodeospf3TimersKickOffStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.4.1 | Scalarospf3TmrsKckOffHello | read-only | current | The sum total number of times the Hello timer has been fired (which triggers the send of a Hello packet) across all OPSF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.4.2 | Scalarospf3TmrsKckOffWait | read-only | current | The sum total number of times the KickOffWait timer has been fired (which triggers the send of a KickOffWait packet) across all OPSF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.4.3 | Scalarospf3TmrsKckOffPoll | read-only | current | The sum total number of times the KickOffPoll timer has been fired (which triggers the send of a KickOffPoll packet) across all OPSF areas and interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.1.4.4 | Scalarospf3TmrsKckOffNbrProbe | read-only | current | The sum total number of times the KickOffNbrProbe timer has been fired (which triggers the send of a KickOffNbrProbe packet) across all OPSF areas and interfac… |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2 | Nodeospf3Area | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1 | Tableospf3AreaRxTxDisdStats | not-accessible | current | The table of Ospf3 Area Rx/Tx Statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1 | Rowospf3AreaRxTxDisdStatsEntry | not-accessible | current | Rx Tx packet Statistics about a Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1.1 | Columnospf3AreaRxTxDisdIndex | read-only | current | The index of the ospf3 Area for which these statistics apply. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1.2 | Columnospf3AreaRxPkts | read-only | current | The total number of Ospf3 packets received in this Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1.3 | Columnospf3AreaTxPkts | read-only | current | The total number of Ospf3 packets transmitted in this Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1.4 | Columnospf3AreaDisdPkts | read-only | current | The total number of Ospf3 packets discaded in this Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1.5 | Columnospf3AreaRxHello | read-only | current | The total number of Hello packets received in this Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1.6 | Columnospf3AreaTxHello | read-only | current | The total number of Hello packets transmitted in this Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1.7 | Columnospf3AreaDisdHello | read-only | current | The total number of Hello packets discaded in this Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1.8 | Columnospf3AreaRxDatabase | read-only | current | The total number of Database Description packets transmitted for this Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1.9 | Columnospf3AreaTxDatabase | read-only | current | The total number of Database Description packets transmitted for this Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1.10 | Columnospf3AreaDisdDatabase | read-only | current | The total number of Database Description packets discarded for this Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1.11 | Columnospf3AreaRxlsReqs | read-only | current | The total number of Link State Request packets received for this Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1.12 | Columnospf3AreaTxlsReqs | read-only | current | The total number of Link State Request packets transmitted for this Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1.13 | Columnospf3AreaDisdlsReqs | read-only | current | The total number of Link State Request packets discarded for this Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1.14 | Columnospf3AreaRxlsAcks | read-only | current | The total number of Link State Acknowledgement packets received for this Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1.15 | Columnospf3AreaTxlsAcks | read-only | current | The total number of Link State Acknowledgement packets transmitted for this Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1.16 | Columnospf3AreaDisdlsAcks | read-only | current | The total number of Link State Acknowledgement packets discarded for this Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1.17 | Columnospf3AreaRxlsUpdates | read-only | current | The total number of Link State Update packets received for this Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1.18 | Columnospf3AreaTxlsUpdates | read-only | current | The total number of Link State Update packets transmitted for this Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.1.1.19 | Columnospf3AreaDisdlsUpdates | read-only | current | The total number of Link State Update packets discarded for this Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.2 | Tableospf3AreaNbrChangeStats | not-accessible | current | The table of Ospf3 Neighbor change Statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.2.1 | Rowospf3AreaNbrChangeStatsEntry | not-accessible | current | Ospf3 Neighbor Change statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.2.1.1 | Columnospf3AreaNbrIndex | read-only | current | The index of the Ospf3 Area for which these statistics apply. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.2.1.2 | Columnospf3AreaNbrDown | read-only | current | The total number of times neighbors now existing on this area have changed into DOWN state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.2.1.3 | Columnospf3AreaNbrAttempt | read-only | current | The total number of times neighbors now existing on this area have changed into ATTEMPT state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.2.1.4 | Columnospf3AreaNbrInit | read-only | current | The total number of times neighbors now existing on this area have changed into INIT state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.2.1.5 | Columnospf3AreaNbrN2way | read-only | current | The total number of times neighbors now existing on this area have changed into 2WAY state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.2.1.6 | Columnospf3AreaNbrExStart | read-only | current | The total number of times neighbors now existing on this area have changed into EXSTART state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.2.1.7 | Columnospf3AreaNbrExchange | read-only | current | The total number of times neighbors now existing on this area have changed into EXCHANGE state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.2.1.8 | Columnospf3AreaNbrLoading | read-only | current | The total number of times neighbors now existing on this area have changed into LOADING state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.2.1.9 | Columnospf3AreaNbrFull | read-only | current | The total number of times neighbors now existing on this area have changed into FULL state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.2.1.10 | Columnospf3AreaNbrAllEvents | read-only | current | The total number of times neighbors now existing on this area have changed state or an error had occured. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.3 | Tableospf3AreaIntfChangeStats | not-accessible | current | The table of Ospf3 Interface change Statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.3.1 | Rowospf3AreaIntfChangeStatsEntry | not-accessible | current | Ospf3 interface Change statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.3.1.1 | Columnospf3AreaIntfIndex | read-only | current | The index of the Ospf3 Interface for which these statistics apply. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.3.1.2 | Columnospf3AreaIntfDown | read-only | current | The total number of changes into the DOWN State of the interfaces associated with this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.3.1.3 | Columnospf3AreaIntfLoop | read-only | current | The total number of changes into the LOOP State of the interfaces associated with this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.3.1.4 | Columnospf3AreaIntfWaiting | read-only | current | The total number of changes into the WAITING State of the interfaces associated with this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.3.1.5 | Columnospf3AreaIntfPtop | read-only | current | The total number of changes into the PTOP State of the interfaces associated with this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.3.1.6 | Columnospf3AreaIntfDr | read-only | current | The total number of changes into the DR State of the interfaces associated with this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.3.1.7 | Columnospf3AreaIntfBackup | read-only | current | The total number of changes into the BACKUP State of the interfaces associated with this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.3.1.8 | Columnospf3AreaIntfDrOther | read-only | current | The total number of changes into the DROTHER State of the interfaces associated with this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.3.1.9 | Columnospf3AreaIntfAllEvents | read-only | current | The total number of State changes of the interfaces associated with this OSPF area |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.4 | Tableospf3AreaErrorStats | not-accessible | current | The table of Ospf3 Interface Error Statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.4.1 | Rowospf3AreaErrorStatsEntry | not-accessible | current | Error Statistics for an Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.4.1.1 | Columnospf3AreaErrIndex | read-only | current | The index of the Ospf3 Area for which these statistics apply. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.4.1.2 | Columnospf3AreaErrRxOnPasv | read-only | current | The total number of packets received by all of the interfaces in this area that are received on a passive interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.4.1.3 | Columnospf3AreaErrRxOspfOff | read-only | current | The total number of packets received by all of the interfaces in this area that are received while OSPF was disabled. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.4.1.4 | Columnospf3AreaErrRxOnNotup | read-only | current | The total number of packets received by all of the interfaces in this area that are received while the interface was disabled. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.4.1.5 | Columnospf3AreaErrRxVerMismatch | read-only | current | The total number of packets received by all of the interfaces in this area that have an OSPF version number not equal to the one of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.4.1.6 | Columnospf3AreaErrRxZeroRTRID | read-only | current | The total number of packets received by all of the interfaces in this area that have a RouterID of 0. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.4.1.7 | Columnospf3AreaErrRxSameRTRID | read-only | current | The total number of packets received by all of the interfaces in this area that have the same RouterID as this Router. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.4.1.8 | Columnospf3AreaErrRxMismatchInstID | read-only | current | The total number of packets received by all of the interfaces in this area that have an instance number not equal to the one of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.4.1.9 | Columnospf3AreaErrBadAreaID | read-only | current | The total number of packets received by all of the interfaces in this area that have an area number not equal to the one of the area of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.4.1.10 | Columnospf3AreaErrBadDestAddr | read-only | current | The total number of packets discarded by all of the interfaces in this area because of a destination address mismatch. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.4.1.11 | Columnospf3AreaErrBadChecksum | read-only | current | The total number of packets discarded by all of the interfaces in this area because of a bad checksum. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.4.1.12 | Columnospf3AreaErrBadNeighbour | read-only | current | The total number of packets discarded by all of the interfaces in this area because they could not be associated with any neighbor. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.4.1.13 | Columnospf3AreaErrBadPktType | read-only | current | The total number of packets discarded by all of the interfaces in this area because the packet type was not recognized. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.4.1.14 | Columnospf3AreaErrHelloMismatch | read-only | current | The total number of packets received with a different hello interval by all of the interfaces in this area . |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.4.1.15 | Columnospf3AreaErrOptionsMismatch | read-only | current | The total number of packets received with a different options by all of the interfaces in this area . |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.4.1.16 | Columnospf3AreaErrDeadMismatch | read-only | current | The total number of packets received with a different dead interval in this area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.2.4.1.17 | Columnospf3AreaErrHelloNoNbr | read-only | current | The total number of packets received from an unknown neighbor when all of the interfaces in this area has a Network Type of NBMA or PTOMP. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3 | Nodeospf3Interface | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1 | Tableospf3IntfRxTxDisdStats | not-accessible | current | The table of Ospf3 Intf Rx/Tx Statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1 | Rowospf3IntfRxTxDisdStatsEntry | not-accessible | current | Rx Tx packet Statistics about a Ospf3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1.1 | Columnospf3IntfRxTxDisdIndex | read-only | current | The index of the ospf3 Intf for which these statistics apply. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1.2 | Columnospf3IntfRxPkts | read-only | current | The total number of Ospf3 packets received on this Ospf3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1.3 | Columnospf3IntfTxPkts | read-only | current | The total number of Ospf3 packets transmitted on this Ospf3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1.4 | Columnospf3IntfDisdPkts | read-only | current | The total number of Ospf3 packets discaded on this Ospf3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1.5 | Columnospf3IntfRxHello | read-only | current | The total number of Hello packets received on this Ospf3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1.6 | Columnospf3IntfTxHello | read-only | current | The total number of Hello packets transmitted on this Ospf3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1.7 | Columnospf3IntfDisdHello | read-only | current | The total number of Hello packets discaded in this Ospf3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1.8 | Columnospf3IntfRxDatabase | read-only | current | The total number of Database Description packets transmitted for this Ospf3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1.9 | Columnospf3IntfTxDatabase | read-only | current | The total number of Database Description packets transmitted for this Ospf3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1.10 | Columnospf3IntfDisdDatabase | read-only | current | The total number of Database Description packets discarded for this Ospf3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1.11 | Columnospf3IntfRxlsReqs | read-only | current | The total number of Link State Request packets received for this Ospf3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1.12 | Columnospf3IntfTxlsReqs | read-only | current | The total number of Link State Request packets transmitted for this Ospf3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1.13 | Columnospf3IntfDisdlsReqs | read-only | current | The total number of Link State Request packets discarded for this Ospf3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1.14 | Columnospf3IntfRxlsAcks | read-only | current | The total number of Link State Acknowledgement packets received for this Ospf3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1.15 | Columnospf3IntfTxlsAcks | read-only | current | The total number of Link State Acknowledgement packets transmitted for this Ospf3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1.16 | Columnospf3IntfDisdlsAcks | read-only | current | The total number of Link State Acknowledgement packets discarded for this Ospf3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1.17 | Columnospf3IntfRxlsUpdates | read-only | current | The total number of Link State Update packets received for this Ospf3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1.18 | Columnospf3IntfTxlsUpdates | read-only | current | The total number of Link State Update packets transmitted for this Ospf3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.1.1.19 | Columnospf3IntfDisdlsUpdates | read-only | current | The total number of Link State Update packets discarded for this Ospf3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.2 | Tableospf3IntfNbrChangeStats | not-accessible | current | The table of Ospf3 Interface Neighbour change Statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.2.1 | Rowospf3IntfNbrChangeStatsEntry | not-accessible | current | Ospf3 interface Neighbour Change statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.2.1.1 | Columnospf3IntfNbrIndex | read-only | current | The index of the Ospf3 Interface for which these statistics apply. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.2.1.2 | Columnospf3IntfNbrDown | read-only | current | The total number of times neighbors now existing on this interface have changed into DOWN state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.2.1.3 | Columnospf3IntfNbrAttempt | read-only | current | The total number of times neighbors now existing on this interface have changed into ATTEMPT state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.2.1.4 | Columnospf3IntfNbrInit | read-only | current | The total number of times neighbors now existing on this interface have changed into INIT state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.2.1.5 | Columnospf3IntfNbrN2way | read-only | current | The total number of times neighbors now existing on this interface have changed into 2WAY state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.2.1.6 | Columnospf3IntfNbrExStart | read-only | current | The total number of times neighbors now existing on this interface have changed into EXSTART state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.2.1.7 | Columnospf3IntfNbrExchange | read-only | current | The total number of times neighbors now existing on this interface have changed into EXCHANGE state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.2.1.8 | Columnospf3IntfNbrLoading | read-only | current | The total number of times neighbors now existing on this interface have changed into LOADING state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.2.1.9 | Columnospf3IntfNbrFull | read-only | current | The total number of times neighbors now existing on this interface have changed into FULL state. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.2.1.10 | Columnospf3IntfNbrAllEvents | read-only | current | The total number of times neighbors now existing on this interface have changed state or an error had occured. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.3 | Tableospf3IntfChangeStats | not-accessible | current | The table of Ospf3 Interface change Statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.3.1 | Rowospf3IntfChangeStatsEntry | not-accessible | current | Ospf3 interface Change statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.3.1.1 | Columnospf3IntfIndex | read-only | current | The index of the Ospf3 Interface for which these statistics apply. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.3.1.2 | Columnospf3IntfDown | read-only | current | The total number of times the interface was down. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.3.1.3 | Columnospf3IntfLoop | read-only | current | The total number of times this interface changed State into the LOOP State. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.3.1.4 | Columnospf3IntfWaiting | read-only | current | The total number of times this interface changed State into the Waiting State. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.3.1.5 | Columnospf3IntfPtop | read-only | current | The total number of times this interface changed State into the PTOP State. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.3.1.6 | Columnospf3IntfDr | read-only | current | The total number of times this interface changed State into the DR State. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.3.1.7 | Columnospf3IntfBackup | read-only | current | The total number of times this interface changed State into the Backup State. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.3.1.8 | Columnospf3IntfDrOther | read-only | current | The total number of times this interface changed State into the DrOther State. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.3.1.9 | Columnospf3IntfAllEvents | read-only | current | The total number of times this interface changed State. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4 | Tableospf3IntfErrorStats | not-accessible | current | The table of Ospf3 Interface Error Statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4.1 | Rowospf3IntfErrorStatsEntry | not-accessible | current | Error Statistics for an Ospf3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4.1.1 | Columnospf3IntfErrIndex | read-only | current | The index of the Ospf3 Intf for which these statistics apply. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4.1.2 | Columnospf3IntfErrRxOnPasv | read-only | current | The total number of packets received by this interface that are received on a passive interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4.1.3 | Columnospf3IntfErrRxOspfOff | read-only | current | The total number of packets received by this interface that are received while OSPF was disabled. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4.1.4 | Columnospf3IntfErrRxOnNotup | read-only | current | The total number of packets received by this interface that are received while the interface was disabled. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4.1.5 | Columnospf3IntfErrRxVerMismatch | read-only | current | The total number of packets received by this interface that have an OSPF version number not equal to the one of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4.1.6 | Columnospf3IntfErrRxZeroRTRID | read-only | current | The total number of packets received by this interface that have a RouterID of 0. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4.1.7 | Columnospf3IntfErrRxSameRTRID | read-only | current | The total number of packets received by this interface that have the same RouterID as this Router. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4.1.8 | Columnospf3IntfErrRxMismatchInstID | read-only | current | The total number of packets received by this interface that have an instance number not equal to the one of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4.1.9 | Columnospf3IntfErrBadAreaID | read-only | current | The total number of packets received by this interface that have an area number not equal to the one of the area of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4.1.10 | Columnospf3IntfErrBadDestAddr | read-only | current | The total number of packets discarded by this interface because of a destination address mismatch. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4.1.11 | Columnospf3IntfErrBadChecksum | read-only | current | The total number of packets discarded by this interface because of a bad checksum. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4.1.12 | Columnospf3IntfErrBadNeighbour | read-only | current | The total number of packets discarded by this interface because they could not be associated with any neighbor. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4.1.13 | Columnospf3IntfErrBadPktType | read-only | current | The total number of packets discarded by this interface because the packet type was not recognized. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4.1.14 | Columnospf3IntfErrHelloMismatch | read-only | current | The total number of packets received with a different hello interval by this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4.1.15 | Columnospf3IntfErrOptionsMismatch | read-only | current | The total number of packets received with a different options by this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4.1.16 | Columnospf3IntfErrDeadMismatch | read-only | current | The total number of packets received with a different dead interval by this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4.1.17 | Columnospf3IntfErrMTUMismatch | read-only | current | The total number of packets received with a different MTU size by this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.22.3.4.1.18 | Columnospf3IntfErrHelloNoNbr | read-only | current | The total number of packets received from an unknown neighbor when this interface has a Network Type of NBMA or PTOMP. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23 | NodemldStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1 | TablemldIfStatsTable | not-accessible | current | The table listing the interfaces on which MLD is enabled. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1 | RowmldIfStatsEntry | not-accessible | current | An entry representing an interface stats on which MLD is enabled. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.1 | ColumnmldIfStatsIfIndex | read-only | current | The internetwork-layer interface value of the interface for which MLD msg stats is counted. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.2 | ColumnrxMldIfStatsGeneralQuery | read-only | current | The total number of MLD Listener Queries received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.3 | ColumnrxMldIfStatsMASQuery | read-only | current | The total number of MLD Listener MAS Queries received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.4 | ColumnrxMldIfStatsMASSQQuery | read-only | current | The total number of MLD Listener MASSQ Queries received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.5 | ColumnrxMldIfStatsMLDv1Report | read-only | current | The total number of MLD Listener Reports (v1) received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.6 | ColumnrxMldIfStatsMLDv1Done | read-only | current | The total number of MLD Listener Dones (v1/v2) received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.7 | ColumnrxMldIfStatsMLDv2Report | read-only | current | The total number of MLD Listener Reports (v2) received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.8 | ColumnrxMldIfStatsIncCrsv2 | read-only | current | The total number of MLD INC CRs (v2) received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.9 | ColumnrxMldIfStatsExcCrsv2 | read-only | current | The total number of MLD EXC CRs (v2) received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.10 | ColumnrxMldIfStatsToIncFmcrsv2 | read-only | current | The total number of MLD TO_INC FMCRs (v2) received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.11 | ColumnrxMldIfStatsToExcFmcrsv2 | read-only | current | The total number of MLD TO_EXC FMCRs (v2) received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.12 | ColumnrxMldIfStatsAllowSlcrsv2 | read-only | current | The total number of MLD ALLOW SLCRs (v2) received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.13 | ColumnrxMldIfStatsBlockSlcrsv2 | read-only | current | The total number of MLD BLOCK SLCRs (v2) received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.14 | ColumntxMldIfStatsGeneralQuery | read-only | current | The total number of MLD Listener Queries sent. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.15 | ColumntxMldIfStatsMASQuery | read-only | current | The total number of MLD Listener MAS Queries sent. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.16 | ColumntxMldIfStatsMASSQQuery | read-only | current | The total number of MLD Listener MASSQ Queries sent. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.17 | ColumntxMldIfStatsMLDv1Report | read-only | current | The total number of MLD Listener Reports (v1) sent. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.18 | ColumntxMldIfStatsMLDv1Done | read-only | current | The total number of MLD Listener Dones (v1/v2) sent. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.19 | ColumntxMldIfStatsMLDv2Report | read-only | current | The total number of MLD Listener Reports (v2) sent. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.20 | ColumntxMldIfStatsIncCrsv2 | read-only | current | The total number of MLD INC CRs (v2) sent |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.21 | ColumntxMldIfStatsExcCrsv2 | read-only | current | The total number of MLD EXC CRs (v2) sent |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.22 | ColumntxMldIfStatsToIncFmcrsv2 | read-only | current | The total number of MLD TO_INC FMCRs (v2) sent |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.23 | ColumntxMldIfStatsToExcFmcrsv2 | read-only | current | The total number of MLD TO_EXC FMCRs (v2) sent |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.24 | ColumntxMldIfStatsAllowSlcrsv2 | read-only | current | The total number of MLD ALLOW SLCRs (v2) sent |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.25 | ColumntxMldIfStatsBlockSlcrsv2 | read-only | current | The total number of MLD BLOCK SLCRs (v2) received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.27 | ColumnerrMldIfStatsGeneralQuery | read-only | current | The total number of MLD Listener Queries errors. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.28 | ColumnerrMldIfStatsMASQuery | read-only | current | The total number of MLD Listener MAS Queries errors. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.29 | ColumnerrMldIfStatsMASSQQuery | read-only | current | The total number of MLD Listener MASSQ Queries errors. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.30 | ColumnerrMldIfStatsMLDv1Report | read-only | current | The total number of MLD Listener Report (v1) errors. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.31 | ColumnerrMldIfStatsMLDv1Done | read-only | current | The total number of MLD Listener Done (v1/v2) errors. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.32 | ColumnerrMldIfStatsMLDv2Report | read-only | current | The total number of MLD Listener Report (v2) errors. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.33 | ColumnerrMldIfStatsIncCrsv2 | read-only | current | The total number of MLD INC CRs (v2) errors. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.34 | ColumnerrMldIfStatsExcCrsv2 | read-only | current | The total number of MLD EXC CRs (v2) errors. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.35 | ColumnerrMldIfStatsToIncFmcrsv2 | read-only | current | The total number of MLD TO_INC FMCRs (v2) errors. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.36 | ColumnerrMldIfStatsToExcFmcrsv2 | read-only | current | The total number of MLD TO_EXC FMCRs (v2) errors. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.37 | ColumnerrMldIfStatsAllowSlcrsv2 | read-only | current | The total number of MLD ALLOW SLCRs (v2) errors. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.1.1.38 | ColumnerrMldIfStatsBlockSlcrsv2 | read-only | current | The total number of MLD BLOCK SLCRs (v2) errors. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.2 | ScalarmldStatBadLength | read-only | current | The total number of bad length mld packet. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.3 | ScalarmldStatBadChecksum | read-only | current | The total number of bad checksum mld packet. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.4 | ScalarmldStatBadReceiveIf | read-only | current | The total number of bad reveive if mld packet. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.5 | ScalarmldStatReceiveNonLocal | read-only | current | The total number of non local received mld packet. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.6 | ScalarmldStatInvalidPkts | read-only | current | The total number of invalid packets. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.7 | ScalarmldStatTotalL3Ipv6SgvEntries | read-only | current | Total L3 IPv6 (S, G, V) entries |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.8 | ScalarmldStatTotalMLDGroups | read-only | current | The total number of MLD Groups. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.23.9 | ScalarmldStatClearAll | read-write | current | Clear all MLD stats. Returns other(1) when read. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.24 | NodeipsecStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.24.1 | TableipsecSaStatsTable | not-accessible | current | The (conceptual) table listing all of the IPsec SA statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.24.1.1 | RowipsecSaStatsEntry | not-accessible | current | An entry (conceptual row) representing a IPsec SA statistics. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.24.1.1.1 | ColumnipsecSaStatsIndex | read-only | current | The index of ipsecSaStatsEntry. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.24.1.1.2 | ColumnipsecSaStatsSpi | read-only | current | The SPI used by the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.24.1.1.3 | ColumnipsecSaStatsProto | read-only | current | The proto(AH,ESP,or Both) used by the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.24.1.1.4 | ColumnipsecSaStatsDstAddr | read-only | current | The destination IP address for the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.24.1.1.5 | ColumnipsecSaStatsUsageTime | read-only | current | The time (in seconds) since the SA was first used. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.24.1.1.6 | ColumnipsecSaStatsBytes | read-only | current | The count of bytes for the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.24.1.1.7 | ColumnipsecSaStatsPkts | read-only | current | The number of packets sent or received for the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.25 | NodedhcpsnpStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.25.1 | ScalardhcpSnoopingStatInPacketRequest | read-only | current | Counter of DHCP REQUEST messages received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.25.2 | ScalardhcpSnoopingStatInPacketReply | read-only | current | Counter of DHCP REPLY messages received. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.25.3 | ScalardhcpSnoopingStatDroppedPacketInvalid | read-only | current | Counter of dropped DHCP messages due to invalid packet. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.25.4 | ScalardhcpSnoopingStatDroppedPacketRateLimit | read-only | current | Counter of dropped DHCP messages due to Rate Limit in software. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.25.5 | ScalardhcpSnoopingStatDroppedPacketOther | read-only | current | Counter of dropped DHCP messages due to other reason. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.26 | NodenbrStats | |||
| 1.3.6.1.4.1.26543.2.7.7.3.2.26.1 | ScalarnbrStatEntries | read-only | current | The current number of NBR entries. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.26.2 | ScalarnbrStatHighWater | read-only | current | The highest number of NBR entries. |
| 1.3.6.1.4.1.26543.2.7.7.3.2.26.3 | ScalarnbrStatMaxEntries | read-only | current | The maximum number of NBR entries. |
| 1.3.6.1.4.1.26543.2.7.7.3.3 | Nodelayer3Info | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.1 | NodeipRoutingInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.1.1 | TableipRouteInfoTable | not-accessible | current | The table of run-time IP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.1.1.1 | RowipRouteInfoEntry | not-accessible | current | A row in the run-time IP route table |
| 1.3.6.1.4.1.26543.2.7.7.3.3.1.1.1.1 | ColumnipRouteInfoIndx | read-only | current | The index of this route table. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.1.1.1.2 | ColumnipRouteInfoDestIp | read-only | current | The destination IP address of this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.1.1.1.3 | ColumnipRouteInfoMask | read-only | current | The destination IP mask of this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.1.1.1.4 | ColumnipRouteInfoGateway | read-only | current | The next-hop router address for this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.1.1.1.5 | ColumnipRouteInfoTag | read-only | current | The tag-type for this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.1.1.1.6 | ColumnipRouteInfoType | read-only | current | The type of the route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.1.1.1.7 | ColumnipRouteInfoInterface | read-only | current | The interface number for which the destination address is applicable. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.1.1.1.8 | ColumnipRouteInfoGateway1 | read-only | current | The next-hop router address for this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.1.1.1.9 | ColumnipRouteInfoGateway2 | read-only | current | The next-hop router address for this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.1.1.1.10 | ColumnipRouteInfoMetric | read-only | current | The Metric for this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.1.2 | ScalarrouteTableClear | read-write | current | Setting this value to clear(2) clears the route table. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.2 | NodearpInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.2.1 | TablearpInfoTable | not-accessible | current | The table of ARP entries. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.2.1.1 | RowarpInfoEntry | not-accessible | current | A row in the ARP table |
| 1.3.6.1.4.1.26543.2.7.7.3.3.2.1.1.1 | ColumnarpInfoDestIp | read-only | current | The destination IP address of the ARP entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.2.1.1.2 | ColumnarpInfoMacAddr | read-only | current | The MAC address for the ARP entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.2.1.1.3 | ColumnarpInfoVLAN | read-only | current | The VLAN identifier for the ARP entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.2.1.1.4 | ColumnarpInfoSrcPortIndex | read-only | current | The port number on which this entry's equivalence is effective. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.2.1.1.6 | ColumnarpInfoFlag | read-only | current | The flag associated with this ARP entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.2.2 | ScalararpCacheClear | read-write | current | Setting this value to clear(2) clears the ARP cache. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.3 | NodevrrpInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.3.1 | TablevrrpInfoVirtRtrTable | not-accessible | current | The table of VRRP virtual router run-time information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.3.1.1 | RowvrrpInfoVirtRtrTableEntry | not-accessible | current | The run-time information about a VRRP virtual router. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.3.1.1.1 | ColumnvrrpInfoVirtRtrIndex | read-only | current | The VRRP virtual router index. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.3.1.1.2 | ColumnvrrpInfoVirtRtrState | read-only | current | The VRRP virtual router state. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.3.1.1.3 | ColumnvrrpInfoVirtRtrOwnership | read-only | current | The VRRP virtual router ownership status. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.3.1.1.4 | ColumnvrrpInfoVirtRtrConfig | read-only | current | The status of the VRRP virtual router. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.3.1.1.5 | ColumnvrrpInfoVirtRtrID | read-only | current | The VRRP virtual router identifier. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.3.1.1.6 | ColumnvrrpInfoVirtRtrAddr | read-only | current | The VRRP virtual router IP address. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.3.1.1.7 | ColumnvrrpInfoVirtRtrIfIndex | read-only | current | The IfIndex that the VRRP virtual router is representing. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.3.1.1.8 | ColumnvrrpInfoVirtRtrPriority | read-only | current | The priority value to be used by the specified VRRP virtual routers. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.3.2 | ScalarvrrpInfoVirtGroupState | read-only | current | VRRP group state. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.3.3 | ScalarvrrpInfoVirtGroupPriority | read-only | current | VRRP group priority. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4 | Nodeospfinfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.1 | NodeospfGeneralInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.1.1 | ScalarospfStartTime | read-only | current | The time when ospf has been started. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.1.2 | ScalarospfProcessUptime | read-only | current | The time since ospf has been started. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.1.3 | ScalarospfLsTypesSupported | read-only | current | The Link State Types that are supported. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.1.4 | ScalarospfIntfCountForRouter | read-only | current | The number of interfaces for this router. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.1.5 | ScalarospfVlinkCountForRouter | read-only | current | The number of virtual links for this router. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.1.6 | ScalarospfTotalNeighbours | read-only | current | The total number of OSPF neighbours. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.1.7 | ScalarospfNbrInInitState | read-only | current | The number of neighbours in the initial state of exchange. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.1.8 | ScalarospfNbrInExchState | read-only | current | The number of neighbours in the exchange state. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.1.9 | ScalarospfNbrInFullState | read-only | current | The number of neighbours in the Full state of exchange. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.1.10 | ScalarospfTotalAreas | read-only | current | The Total number of areas. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.1.11 | ScalarospfTotalTransitAreas | read-only | current | The Total number of Transit areas. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.1.12 | ScalarospfTotalNssaAreas | read-only | current | The Total number of NSSA areas. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.1.13 | ScalarospfTotalStubAreas | read-only | current | The Total number of STUB areas. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.2 | TableospfAreaInfoTable | not-accessible | current | The table of OSPF Area information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.2.1 | RowospfAreaInfoEntry | not-accessible | current | Information about a OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.2.1.1 | ColumnospfAreaInfoIndex | read-only | current | The OSPF area number for which the OSPF info table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.2.1.2 | ColumnospfAreaInfoId | read-only | current | The IP address of the OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.2.1.3 | ColumnospfTotalNumberOfInterfaces | read-only | current | The total number of interfaces for this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.2.1.4 | ColumnospfNumberOfInterfacesUp | read-only | current | The number of interfaces UP in area. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.2.1.5 | ColumnospfNumberOfLsdbEntries | read-only | current | The number of Link State Database entries for this OSPF area. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.2.1.6 | ColumnospfAreaInfoAuthType | read-only | current | Area authentication. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.2.1.7 | ColumnospfAreaInfoLsTypesAccepted | read-only | current | LS types accepted by this area. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.2.1.8 | ColumnospfAreaInfoSPF | read-only | current | Number of times SPF algorithm has been executed. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.2.1.9 | ColumnospfAreaInfoAreaBorderRouter | read-only | current | Count of ABR local to this area. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.2.1.10 | ColumnospfAreaInfoASBoundaryRouter | read-only | current | Count of ASBR local to this area. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.2.1.11 | ColumnospfAreaInfoTotalNeighbours | read-only | current | The total number of OSPF neighbors. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.2.1.12 | ColumnospfAreaInfoNeighborsINITstate | read-only | current | Total neighbors in INIT state. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.2.1.13 | ColumnospfAreaInfoNeighborsEXCHstate | read-only | current | Total neighbors in EXCH state. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.2.1.14 | ColumnospfAreaInfoNeighborsFULLstate | read-only | current | Total neighbors in FULL state. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3 | TableospfIntfInfoTable | not-accessible | current | The table of OSPF Interface information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1 | RowospfIntfInfoEntry | not-accessible | current | Information about a OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.1 | ColumnospfIfInfoIndex | read-only | current | The OSPF interface number for which the OSPF info table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.2 | ColumnospfIfInfoIpAddress | read-only | current | The IP address of the OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.3 | ColumnospfIfInfoArea | read-only | current | The index of the area that the interface belongs. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.4 | ColumnospfIfInfoAdminStatus | read-only | current | Admin Status of the interface: down(0), up(1). |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.5 | ColumnospfIfInfoPassive | read-only | current | Passive status of the interface: disabled(0), enabled(1). |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.6 | ColumnospfIfInfoRouterIP | read-only | current | The router ID of the switch. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.7 | ColumnospfIfInfoState | read-only | current | The state of the interface: Down(0), Loopback(1), Waiting(2), P to P(3), DR(4), BackuDR(5), DR Other(6). |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.8 | ColumnospfIfInfoPriority | read-only | current | Interface router priority |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.9 | ColumnospfIfInfoDesignatedRouterIP | read-only | current | The OSPF Designated Router IP (IP Address) for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.10 | ColumnospfIfInfoDesignatedRouterIpAddress | read-only | current | The OSPF Designated Router IP Address for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.11 | ColumnospfIfInfoBackupDesignatedRouterIP | read-only | current | The OSPF Backup Designated Router IP for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.12 | ColumnospfIfInfoBackupDesignatedRouterIpAddress | read-only | current | The OSPF Backup Designated Router Ip Address for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.13 | ColumnospfIfInfoHello | read-only | current | The hello timer for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.14 | ColumnospfIfInfoHelloMS | read-only | current | Units of time measurement for Hello interval seconds(0), milliseconds(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.15 | ColumnospfIfInfoDead | read-only | current | The dead timer for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.16 | ColumnospfIfInfoDeadMS | read-only | current | Units of time measurement for Dead interval seconds(0), milliseconds(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.17 | ColumnospfIfInfoWaitInterval | read-only | current | The OSPF Wait interval for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.18 | ColumnospfIfInfoWaitIntervalMS | read-only | current | Units of time measurement for Wait interval seconds(0), milliseconds(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.19 | ColumnospfIfInfoRetransmit | read-only | current | The retransmit interval for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.20 | ColumnospfIfInfoTransitDelay | read-only | current | The transit delay for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.21 | ColumnospfIfInfoTotalNeighbours | read-only | current | The Total number of neighbours for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.22 | ColumnospfIfInfoEvents | read-only | current | The total number of events for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.23 | ColumnospfIfInfoAuthType | read-only | current | Type of authentication being used: none(1) - no authentication, password(2) - use password, md5(3) - use MD5 authentication. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.3.1.24 | ColumnospfIfInfoPtop | read-only | current | Point-to-point status of the interface: disabled(0), enabled(1). |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4 | TableospfVirtIntfInfoTable | not-accessible | current | The table of OSPF virtual interfaces information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1 | RowospfVirtIntfInfoEntry | not-accessible | current | Information about an OSPF virtual interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1.1 | ColumnospfVirtIntfInfoIndex | read-only | current | The OSPF Virtual Interface number for which this table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1.2 | ColumnospfVirtIntfInfoIpAddr | read-only | current | The IP Address of this virtual interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1.3 | ColumnospfVirtIntfInfoArea | read-only | current | The index of the OSPF area to which this virtual interface belongs. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1.4 | ColumnospfVirtIntfInfoRouterId | read-only | current | The Router ID. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1.5 | ColumnospfVirtIntfInfoState | read-only | current | State disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1.6 | ColumnospfVirtIntfInfoCost | read-only | current | The cost of the virtual interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1.7 | ColumnospfVirtIntfInfoTrans | read-only | current | The transit delay for the virtual interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1.8 | ColumnospfVirtIntfInfoHello | read-only | current | Hello interval. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1.9 | ColumnospfVirtIntfInfoHelloMS | read-only | current | Units of time measurement for Hello interval seconds(0), milliseconds(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1.10 | ColumnospfVirtIntfInfoDead | read-only | current | Dead interval. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1.11 | ColumnospfVirtIntfInfoDeadMS | read-only | current | Units of time measurement for Dead interval seconds(0), milliseconds(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1.12 | ColumnospfVirtIntfInfoWait | read-only | current | Wait interval. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1.13 | ColumnospfVirtIntfInfoWaitMS | read-only | current | Units of time measurement for Wait interval seconds(0), milliseconds(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1.14 | ColumnospfVirtIntfInfoRetra | read-only | current | Retransmit interval. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1.15 | ColumnospfVirtIntfInfoAuth | read-only | current | Authentication. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1.16 | ColumnospfVirtIntfInfoEvents | read-only | current | Events. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1.17 | ColumnospfVirtIntfInfoNbr | read-only | current | The IP Address of the OSPF neighbor for this virtual interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1.18 | ColumnospfVirtIntfInfoNbrState | read-only | current | State down(0),attempt(1),init(2),2 way(3), exstart(4),exchange(5),loading(6),full(7) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.4.1.19 | ColumnospfVirtIntfInfoAreaId | read-only | current | The AreaId of the virtual interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.5 | TableospfIfNbrTable | not-accessible | current | The table of OSPF Interface Neighbor information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.5.1 | RowospfIfNbrEntry | not-accessible | current | Information about a OSPF interface, neighbor pair. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.5.1.1 | ColumnospfIfNbrIntfIndex | read-only | current | The OSPF Interface number for which this Interface/Nbr table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.5.1.2 | ColumnospfIfNbrIpAddr | read-only | current | The OSPF Neighbor ID . |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.5.1.3 | ColumnospfIfNbrPriority | read-only | current | The priority of the OSPF neighbor. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.5.1.4 | ColumnospfIfNbrState | read-only | current | The state of the OSPF neighbor. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.5.1.5 | ColumnospfIfNbrDesignatedRtr | read-only | current | The IP Address of the Designated Router for this OSPF Neighbor. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.5.1.6 | ColumnospfIfNbrBackupDesignatedRtr | read-only | current | The IP Address of the backup designated Router for this OSPF Neighbor. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.5.1.7 | ColumnospfIfNbrIpAddress | read-only | current | The IP Address of the OSPF Neighbor. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.6 | TableospfSumRangesInfoTable | not-accessible | current | The table of OSPF summary ranges information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.6.1 | RowospfSumRangesInfoEntry | not-accessible | current | Summary ranges information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.6.1.1 | ColumnospfSumRangesInfoIndex | read-only | current | The OSPF range index for which this table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.6.1.2 | ColumnospfSumRangesInfoArea | read-only | current | Area. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.6.1.3 | ColumnospfSumRangesInfoNetwork | read-only | current | Network. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.6.1.4 | ColumnospfSumRangesInfoMask | read-only | current | Mask. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.6.1.5 | ColumnospfSumRangesInfoAction | read-only | current | Action propagate(0), hide(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.6.1.6 | ColumnospfSumRangesInfoListType | read-only | current | Summary address list Non-NSSA(0), NSSA(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.7 | TableospfRoutesInfoTable | not-accessible | current | The table of OSPF routes information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.7.1 | RowospfRoutesInfoEntry | not-accessible | current | OSPF routes information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.7.1.1 | ColumnospfRoutesInfoIndex | read-only | current | The OSPF route table entry index for which this table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.7.1.2 | ColumnospfRoutesInfoDestination | read-only | current | Destination. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.7.1.3 | ColumnospfRoutesInfoMask | read-only | current | Mask. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.7.1.4 | ColumnospfRoutesInfoVia | read-only | current | Next hop. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.7.1.5 | ColumnospfRoutesInfoType | read-only | current | Route type. Codes: IA - OSPF inter area, N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 * … |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.8 | TableospfLsdbInfoTable | not-accessible | current | The OSPF Process's Link State Database. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.8.1 | RowospfLsdbInfoEntry | not-accessible | current | A single Link State Advertisement. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.8.1.1 | ColumnospfLsdbInfoIndex | read-only | current | The 32 bit index in the table. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.8.1.2 | ColumnospfLsdbInfoAreaId | read-only | current | The 32 bit identifier of the Area from which the LSA was received. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.8.1.3 | ColumnospfLsdbInfoType | read-only | current | The type of the link state advertisement. Each link state type has a separate advertise- ment format. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.8.1.4 | ColumnospfLsdbInfoLsid | read-only | current | The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being desc… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.8.1.5 | ColumnospfLsdbInfoRouterId | read-only | current | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.8.1.6 | ColumnospfLsdbInfoSequence | read-only | current | The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is line… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.8.1.7 | ColumnospfLsdbInfoAge | read-only | current | This field is the age of the link state adver- tisement in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.8.1.8 | ColumnospfLsdbInfoChecksum | read-only | current | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.8.1.9 | ColumnospfLsdbInfoAdvertisement | read-only | current | The entire Link State Advertisement, including its header. When the LSA is invalid, it is message string 'Invalid LSDB'. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.9 | TableospfExtLsdbInfoTable | not-accessible | current | The OSPF Process's Links State Database. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.9.1 | RowospfExtLsdbInfoEntry | not-accessible | current | A single Link State Advertisement. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.9.1.1 | ColumnospfExtLsdbInfoIndex | read-only | current | The 32 bit index in the table. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.9.1.2 | ColumnospfExtLsdbInfoType | read-only | current | The type of the link state advertisement. Each link state type has a separate advertise- ment format. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.9.1.3 | ColumnospfExtLsdbInfoLsid | read-only | current | The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being desc… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.9.1.4 | ColumnospfExtLsdbInfoRouterId | read-only | current | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.9.1.5 | ColumnospfExtLsdbInfoSequence | read-only | current | The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is line… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.9.1.6 | ColumnospfExtLsdbInfoAge | read-only | current | This field is the age of the link state adver- tisement in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.9.1.7 | ColumnospfExtLsdbInfoChecksum | read-only | current | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.9.1.8 | ColumnospfExtLsdbInfoAdvertisement | read-only | current | The entire Link State Advertisement, including its header. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10 | TableospfLoopIfInfoTable | not-accessible | current | The table of OSPF Loopback Interface information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1 | RowospfLoopIfInfoEntry | not-accessible | current | Information about a OSPF loopback interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.1 | ColumnospfLoopIfInfoIndex | read-only | current | The OSPF loopback interface number for which the OSPF info table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.2 | ColumnospfLoopIfInfoIpAddress | read-only | current | The IP address of the OSPF loopback interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.3 | ColumnospfLoopIfInfoArea | read-only | current | The index of the area that the loopback interface belongs. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.4 | ColumnospfLoopIfInfoAdminStatus | read-only | current | Admin Status of the interface: down(0), up(1). |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.5 | ColumnospfLoopIfInfoPassive | read-only | current | Passive status of the interface: disabled(0), enabled(1). |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.6 | ColumnospfLoopIfInfoRouterIP | read-only | current | The router ID of the switch. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.7 | ColumnospfLoopIfInfoState | read-only | current | The state of the interface: Down(0), Loopback(1), Waiting(2), P to P(3), DR(4), BackuDR(5), DR Other(6). |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.8 | ColumnospfLoopIfInfoPriority | read-only | current | Interface router priority |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.9 | ColumnospfLoopIfInfoDesignatedRouterIP | read-only | current | The OSPF Designated Router IP (IP Address) for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.10 | ColumnospfLoopIfInfoDesignatedRouterIpAddress | read-only | current | The OSPF Designated Router IP Address for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.11 | ColumnospfLoopIfInfoBackupDesignatedRouterIP | read-only | current | The OSPF Backup Designated Router IP for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.12 | ColumnospfLoopIfInfoBackupDesignatedRouterIpAddress | read-only | current | The OSPF Backup Designated Router Ip Address for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.13 | ColumnospfLoopIfInfoHello | read-only | current | The hello timer for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.14 | ColumnospfLoopIfInfoHelloMS | read-only | current | Units of time measurement for Hello interval seconds(0), milliseconds(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.15 | ColumnospfLoopIfInfoDead | read-only | current | The dead timer for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.16 | ColumnospfLoopIfInfoDeadMS | read-only | current | Units of time measurement for Dead interval seconds(0), milliseconds(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.17 | ColumnospfLoopIfInfoWaitInterval | read-only | current | The OSPF Wait interval for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.18 | ColumnospfLoopIfInfoWaitIntervalMS | read-only | current | Units of time measurement for Wait interval seconds(0), milliseconds(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.19 | ColumnospfLoopIfInfoRetransmit | read-only | current | The retransmit interval for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.20 | ColumnospfLoopIfInfoTransitDelay | read-only | current | The transit delay for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.21 | ColumnospfLoopIfInfoTotalNeighbours | read-only | current | The Total number of neighbours for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.22 | ColumnospfLoopIfInfoEvents | read-only | current | The total number of events for this OSPF interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.23 | ColumnospfLoopIfInfoAuthType | read-only | current | Type of authentication being used: none(1) - no authentication, password(2) - use password, md5(3) - use MD5 authentication. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.4.10.1.24 | ColumnospfLoopIfInfoPtop | read-only | current | Point-to-point status of the interface: disabled(0), enabled(1). |
| 1.3.6.1.4.1.26543.2.7.7.3.3.5 | NodegatewayInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.5.1 | TablegatewayInfoTable | not-accessible | current | The table containing information for the default gateways. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.5.1.1 | RowgatewayInfoEntry | not-accessible | current | A row in the gateway information table |
| 1.3.6.1.4.1.26543.2.7.7.3.3.5.1.1.1 | ColumngatewayInfoIndex | read-only | current | The gateway number for which the information is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.5.1.1.2 | ColumngatewayInfoAddr | read-only | current | The IP address of the default gateway. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.5.1.1.4 | ColumngatewayInfoStatus | read-only | current | The status of the default gateway. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6 | NodeigmpInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.1 | TableigmpInfoTable | not-accessible | current | The table of IGMP group membership information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.1.1 | RowigmpInfoEntry | not-accessible | current | Information about an IGMP group member . |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.1.1.1 | ColumnigmpInfoIndex | read-only | current | The igmp group number for which the IGMP info table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.1.1.2 | ColumnigmpInfoGroupId | read-only | current | The IP address of the IGMP group. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.1.1.3 | ColumnigmpInfoVlanId | read-only | current | The VLAN ID for this IGMP group. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.1.1.4 | ColumnigmpInfoSrcTrunk | read-only | current | The downstream trunk number. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.1.1.5 | ColumnigmpInfoSrcPortIndex | read-only | current | The downstream port number. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.1.1.6 | ColumnigmpInfoVersion | read-only | current | The Version of IGMP host. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.1.1.7 | ColumnigmpInfoExpires | read-only | current | The expiration time for this host. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.1.1.8 | ColumnigmpInfoMode | read-only | current | The IGMPv3 filter-mode for this host. Returned values: exclude(1) - the IGMPv3 filter-mode is exclude. include(2) - the IGMPv3 filter-mode is include. na(3) - … |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.1.1.9 | ColumnigmpInfoSourceIp | read-only | current | The source IP address of the IGMP group. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.1.1.10 | ColumnigmpInfoFwd | read-only | current | The IGMPv3 forwarding for this source/group IP for this host. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.1.1.11 | ColumnigmpInfoGrpExpires | read-only | current | The expiration time for the group. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.2 | TableigmpMrtrInfoTable | not-accessible | current | The table of IGMP mrouters. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.2.1 | RowigmpMrtrInfoEntry | not-accessible | current | Information about an IGMP mrouter. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.2.1.1 | ColumnigmpMrtrInfoIndex | read-only | current | The mrouter number for which the IGMP mrouter info table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.2.1.2 | ColumnigmpMrtrInfoVlanId | read-only | current | The VLAN ID on which this IGMP mrouter is attached. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.2.1.3 | ColumnigmpMrtrInfoPortId | read-only | current | The port/portchannel alias on which this IGMP mrouter is attached. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.2.1.4 | ColumnigmpMrtrInfoVersion | read-only | current | The version of this IGMP mrouter. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.2.1.5 | ColumnigmpMrtrInfoExpires | read-only | current | The expiration time for this mrouter. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.2.1.6 | ColumnigmpMrtrInfoMrt | read-only | current | The Maximum Query Response time of this IGMP mrouter. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.2.1.7 | ColumnigmpMrtrInfoQrv | read-only | current | The Querier Robustness value of this IGMP mrouter. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.2.1.8 | ColumnigmpMrtrInfoQqic | read-only | current | The Querier query interval code of this IGMP mrouter. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.2.1.10 | ColumnigmpMrtrInfoSrcIp | read-only | current | The Source IP of this IGMP mrouter. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.6.3 | ScalarigmpClearTables | read-write | current | Clear the IGMP tables. When setting clearGroups(1), the dynamic groups are removed, when setting clearMrouters(2), the mrouter tables are removed and when sett… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.8 | NodeipInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.8.1 | ScalaripInfoRouterID | read-only | current | Router ID information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.8.4 | ScalaripInfoBootpRelayState | read-only | current | The state of BOOTP relay. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.8.5 | ScalaripInfoBootpRelayAddr | read-only | current | The IP address of BOOTP server. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.8.6 | ScalaripInfoBootpRelayAddr2 | read-only | current | The IP address of second BOOTP server. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.8.7 | ScalaripInfoFwdState | read-only | current | IP forwarding global state. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.8.8 | ScalaripInfoFwdDirectedBcast | read-only | current | The state of forwarding directed broadcasts. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.9 | NodeipIntfInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.9.1 | TableipIntfInfoTable | not-accessible | current | The table of IP interface information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.9.1.1 | RowintfInfoEntry | not-accessible | current | A row in IP interface information table. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.9.1.1.1 | ColumnintfInfoIndex | read-only | current | The interface number for which the information is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.9.1.1.3 | ColumnintfInfoAddr | read-only | current | The IP address of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.9.1.1.4 | ColumnintfInfoNetMask | read-only | current | The subnet mask of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.9.1.1.5 | ColumnintfInfoBcastAddr | read-only | current | The broadcast address of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.9.1.1.6 | ColumnintfInfoVlan | read-only | current | The VLAN number for this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.9.1.1.7 | ColumnintfInfoStatus | read-only | current | The status of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10 | Noderip2Info | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.1 | Noderip2GeneralInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.1.1 | ScalarripInfoState | read-only | current | RIP global state. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.1.2 | ScalarripInfoUpdatePeriod | read-only | current | Update Period in seconds. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.2 | Tablerip2InfoIntfTable | not-accessible | current | The information table of RIP. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.2.1 | RowripInfoIntfEntry | not-accessible | current | Information about RIP on IP interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.2.1.1 | ColumnripInfoIntfIndex | read-only | current | The interface number for which the RIP information is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.2.1.2 | ColumnripInfoIntfVersion | read-only | current | RIP version. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.2.1.3 | ColumnripInfoIntfAddress | read-only | current | The interface address. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.2.1.4 | ColumnripInfoIntfState | read-only | current | The status of RIP protocol. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.2.1.5 | ColumnripInfoIntfListen | read-only | current | The status of listening to route updates. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.2.1.6 | ColumnripInfoIntfTrigUpdate | read-only | current | The status of triggered updates. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.2.1.7 | ColumnripInfoIntfMcastUpdate | read-only | current | The status of multicast updates. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.2.1.8 | ColumnripInfoIntfPoisonReverse | read-only | current | The status of RIP poison reverse. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.2.1.9 | ColumnripInfoIntfSupply | read-only | current | The status of supplying route updates. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.2.1.10 | ColumnripInfoIntfMetric | read-only | current | RIP route metric for this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.2.1.11 | ColumnripInfoIntfAuth | read-only | current | The type of Authentication used on this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.2.1.12 | ColumnripInfoIntfKey | read-only | current | RIP update authentication password. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.2.1.13 | ColumnripInfoIntfDefault | read-only | current | Specifies what RIP does with default routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.3 | Tablerip2InfoRtrTable | not-accessible | current | The routing information table of RIP. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.3.1 | RowripInfoRtrEntry | not-accessible | current | Information about RIP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.3.1.1 | ColumnripInfoRtrIndex | read-only | current | The index number of RIP route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.3.1.2 | ColumnripInfoRtrDestIp | read-only | current | The destination ip address of this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.3.1.3 | ColumnripInfoRtrMask | read-only | current | The destination ip mask of this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.3.1.4 | ColumnripInfoRtrGateway | read-only | current | The next-hop router address for this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.10.3.1.10 | ColumnripInfoRtrMetric | read-only | current | The metric for this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11 | NodebgpInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1 | TablebgpInfoPeerTable | not-accessible | current | The table of BGP peer in the current configuration block. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1.1 | RowbgpInfoPeerEntry | not-accessible | current | Information about a BGP peer. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1.1.1 | ColumnbgpInfoPeerIndex | read-only | current | The BGP peer number for which the BGP peer table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1.1.2 | ColumnbgpInfoPeerRemoteAddr | read-only | current | The remote IP address of the BGP peer. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1.1.3 | ColumnbgpInfoPeerVersion | read-only | current | The version negotiated by the BGP peer. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1.1.4 | ColumnbgpInfoPeerTtl | read-only | current | The time-to-live value of the BGP peer IP datagram. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1.1.5 | ColumnbgpInfoPeerRemoteAs | read-only | current | The remote IP address of the BGP peer. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1.1.6 | ColumnbgpInfoPeerRouterId | read-only | current | The router IP address. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1.1.7 | ColumnbgpInfoPeerState | read-only | current | The BGP status. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1.1.8 | ColumnbgpInfoPeerLastState | read-only | current | The BGP old status. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1.1.9 | ColumnbgpInfoTotalReceivedPackets | read-only | current | The total number of received packets. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1.1.10 | ColumnbgpInfoTotalSentPackets | read-only | current | The total number of sent packets. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1.1.11 | ColumnbgpInfoReceivedUpdates | read-only | current | The number of received updates. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1.1.12 | ColumnbgpInfoSentUpdates | read-only | current | The number of sent updates. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1.1.13 | ColumnbgpInfoKeepalive | read-only | current | The keep alive time. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1.1.14 | ColumnbgpInfoHoldtime | read-only | current | The hold time. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1.1.15 | ColumnbgpInfoMinAdvTime | read-only | current | The MinAdvTime. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1.1.16 | ColumnbgpInfoLastErrorCode | read-only | current | The last error code. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1.1.17 | ColumnbgpInfoLastErrorSubCode | read-only | current | The last error subcode. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.1.1.18 | ColumnbgpInfoEstTransitions | read-only | current | The established state transitions. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.2 | TablebgpInfoSummaryTable | not-accessible | current | The table of BGP Peer Information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.2.1 | RowbgpInfoSummaryEntry | not-accessible | current | Information about a BGP Peer. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.2.1.1 | ColumnbgpInfoSummaryIndex | read-only | current | The BGP Peer number for which the BGP Peer table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.2.1.2 | ColumnbgpInfoSummaryRemoteAddr | read-only | current | The remote IP address of the BGP Peer. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.2.1.3 | ColumnbgpInfoSummaryVersion | read-only | current | The version negotiated by the BGP Peer. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.2.1.4 | ColumnbgpInfoSummaryRemoteAs | read-only | current | The Remote AS. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.2.1.5 | ColumnbgpInfoSummaryState | read-only | current | The BGP status. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.2.1.6 | ColumnbgpInfoSummaryTotalReceivedPackets | read-only | current | The total number of received packets. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.2.1.7 | ColumnbgpInfoSummaryTotalSentPackets | read-only | current | The total number of sent packets. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.3 | TablebgpInfoRtrTable | not-accessible | current | The table of BGP router run-time information |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.3.1 | RowbgpInfoRtrTableEntry | not-accessible | current | The run-time information about a BGP router |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.3.1.1 | ColumnbgpInfoIndex | read-only | current | The BGP router index which is the network address. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.3.1.2 | ColumnbgpInfoNetwork | read-only | current | The BGP network address. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.3.1.3 | ColumnbgpInfoNextHop | read-only | current | The BGPs NextHop addresses from a network. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.3.1.4 | ColumnbgpInfoMetr | read-only | current | The BGPs metric from a network. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.3.1.5 | ColumnbgpInfoLcPrf | read-only | current | The BGPs local preference from a network. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.3.1.6 | ColumnbgpInfoWght | read-only | current | Total weight of AS paths from a network. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.3.1.7 | ColumnbgpInfoPath | read-only | current | The AS paths from a network. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.3.1.8 | ColumnbgpInfoOrigin | read-only | current | The BGPs route origin from a network |
| 1.3.6.1.4.1.26543.2.7.7.3.3.11.3.1.9 | ColumnbgpInfoMask | read-only | current | The BGP router subnet mask. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.12 | NodenbrInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.12.1 | TablenbrInfoTable | not-accessible | current | The table of nbrcache information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.12.1.1 | RownbrInfoEntry | not-accessible | current | Information about neighbor discovery protocol. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.12.1.1.1 | ColumnnbrInfoIndex | read-only | current | The index of the nbrcache entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.12.1.1.2 | ColumnnbrInfoDestIp | read-only | current | The destination IP address of the nbrcache entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.12.1.1.3 | ColumnnbrInfoState | read-only | current | The state of the nbrcache entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.12.1.1.4 | ColumnnbrInfoMacAddr | read-only | current | The MAC address for the nbrcache entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.12.1.1.5 | ColumnnbrInfoVlanId | read-only | current | The VLAN identifier for the nbrcache entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.12.1.1.6 | ColumnnbrInfoPortNum | read-only | current | The port number on which this entry's equivalence is effective. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.12.1.1.7 | ColumnnbrInfoAge | read-only | current | The used time for the nbrcache entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.12.1.1.8 | ColumnnbrInfoInterface | read-only | current | The interface number for which the destination address is applicable. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.12.2 | ScalarnbrClear | read-write | current | Setting this value to clear(2) clears the Nbr cache, When read ok(1) is returned. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.13 | NodegatewayIPv6Info | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.13.1 | TablegatewayIPv6InfoTable | not-accessible | current | The table containing information for the IPv6 default gateways. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.13.1.1 | RowgatewayIPv6InfoEntry | not-accessible | current | A row in the IPv6 gateway information table |
| 1.3.6.1.4.1.26543.2.7.7.3.3.13.1.1.1 | ColumnipGatewayIPv6InfoIndex | read-only | current | The IPv6 gateway number for which the information is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.13.1.1.2 | ColumnipGatewayIPv6InfoAddr | read-only | current | The IP address for the IPv6 default gateway. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.13.1.1.3 | ColumnipGatewayIPv6InfoState | read-only | current | The state for the IPv6 Default Gateway. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.14 | NodeipRoute6Info | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.14.1 | TableipRoute6InfoTable | not-accessible | current | The table of run-time IP6 routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.14.1.1 | RowipRoute6InfoEntry | not-accessible | current | A row in the run-time IP6 route table. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.14.1.1.1 | ColumnipRoute6InfoIndx | read-only | current | The index of this route6 table. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.14.1.1.2 | ColumnipRoute6InfoDestIp | read-only | current | The destination of the route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.14.1.1.3 | ColumnipRoute6InfoPrefLen | read-only | current | The destination prefix length of the route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.14.1.1.4 | ColumnipRoute6InfoInterface | read-only | current | The interface of the route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.14.1.1.5 | ColumnipRoute6InfoNextHop | read-only | current | The next hop of the route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.14.1.1.6 | ColumnipRoute6InfoProto | read-only | current | The protocol type of the route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.15 | NodedhcpInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.15.1 | ScalardhcpInfoMacAddr | read-only | current | The MAC address of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.15.2 | ScalardhcpInfoAddr | read-only | current | The IP address of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.15.3 | ScalardhcpInfoSubnetMask | read-only | current | The subnet mask of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.15.4 | ScalardhcpInfoDefaultGateway | read-only | current | The IP address of default gateway for the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.15.5 | ScalardhcpInfoServer | read-only | current | The IP address of the DHCP server that leased the ip of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.15.6 | ScalardhcpInfoLeaseObtained | read-only | current | The time and date when the lease was obtained . |
| 1.3.6.1.4.1.26543.2.7.7.3.3.15.7 | ScalardhcpInfoLeaseExpires | read-only | current | The time and date when the lease was obtained . |
| 1.3.6.1.4.1.26543.2.7.7.3.3.16 | NodeipIntfLoopbackInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.16.1 | TableipIntfLoopbackInfoTable | not-accessible | current | The table of IP Loopback interface information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.16.1.1 | RowintfLoopbackInfoEntry | not-accessible | current | A row in IP Loopback interface information table. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.16.1.1.1 | ColumnintfLoopbackInfoIndex | read-only | current | The Loopback interface number for which the information is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.16.1.1.3 | ColumnintfLoopbackInfoAddr | read-only | current | The IP address of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.16.1.1.4 | ColumnintfLoopbackInfoNetMask | read-only | current | The subnet mask of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.16.1.1.5 | ColumnintfLoopbackInfoBcastAddr | read-only | current | The broadcast address of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.16.1.1.7 | ColumnintfLoopbackInfoStatus | read-only | current | The status of the interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18 | Nodeospf3Info | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1 | Nodeospf3GeneralInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.1 | Scalarospf3Version | read-only | current | OSPF version. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.2 | Scalarospf3RouterID | read-only | current | The router ID of the switch. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.3 | Scalarospf3StartTime | read-only | current | The time when ospf has been started. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.4 | Scalarospf3ProcessUptime | read-only | current | The time since ospf has been started. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.5 | Scalarospf3AreaBorderRouter | read-only | current | Area Border Router Role. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.6 | Scalarospf3ASBoundaryRouter | read-only | current | AS Boundary Router Role. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.7 | Scalarospf3ExternalLsa | read-only | current | The number of external LSAs. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.8 | Scalarospf3IntfCountForRouter | read-only | current | The number of interfaces for this router. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.9 | Scalarospf3VlinkCountForRouter | read-only | current | The number of virtual links for this router. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.10 | Scalarospf3NewLsaReceived | read-only | current | The number of new LSAs reveived. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.11 | Scalarospf3TotalLsaOriginated | read-only | current | The number of LSAs originated. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.12 | Scalarospf3TotalNumberOfAsScopeLsas | read-only | current | Total number of entries in the Link State Database. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.13 | Scalarospf3TotalNeighbours | read-only | current | The total number of OSPF neighbours. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.14 | Scalarospf3NbrInXchgOrLoadState | read-only | current | The number of neighbours in the exchange or loading state. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.15 | Scalarospf3TotalAreas | read-only | current | The Total number of areas. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.16 | Scalarospf3TotalActiveAreas | read-only | current | The Total number of areas containing active interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.17 | Scalarospf3TotalNssaAreas | read-only | current | The Total number of NSSA areas. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.18 | Scalarospf3OverFlowState | read-only | current | Indicates whether router is in overflow state or not. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.19 | Scalarospf3SpfDelay | read-only | current | The Delay at which routing calculation is carried after a topology change. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.20 | Scalarospf3SpfHoldTime | read-only | current | The minimum time between two consecutive SPF calculations. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.21 | Scalarospf3ABRType | read-only | current | Different Types of ABRs supported |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.1.22 | Scalarospf3NssaAsbrDefRtTrans | read-only | current | Specifies the P-Bit setting for the default Type-7 LSA generated by ASBR(which is not ABR).When disabled, P-Bit is clear in the generated default Lsa. When ena… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.2 | Tableospf3AreaInfoTable | not-accessible | current | The table of OSPFv3 Area information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.2.1 | Rowospf3AreaInfoEntry | not-accessible | current | Information about a OSPFv3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.2.1.1 | Columnospf3AreaInfoIndex | read-only | current | The OSPFv3 area number for which the OSPFv3 info table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.2.1.2 | Columnospf3AreaInfoId | read-only | current | The IP address of the OSPFv3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.2.1.3 | Columnospf3AreaInfoStatus | read-only | current | Area Status: active(1), notInService(2), notReady(3). |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.2.1.4 | Columnospf3TotalNumberOfInterfaces | read-only | current | The total number of interfaces for this OSPFv3 area. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.2.1.5 | Columnospf3NumberOfInterfacesUp | read-only | current | The number of interfaces UP in area. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.2.1.6 | Columnospf3AreaInfoSPF | read-only | current | The number of times SPF ran. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.2.1.7 | Columnospf3NumberOfLsdbEntries | read-only | current | The total number of Area-scope link state advertisements in this area's link state database. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.2.1.8 | Columnospf3AreaInfoAreaBorderRouter | read-only | current | The Area Border Router count. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.2.1.9 | Columnospf3AreaInfoASBoundaryRouter | read-only | current | The AS Boundary Router count. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.2.1.10 | Columnospf3AreaInfoNeighborsFULLstate | read-only | current | Total neighbors in FULL state. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.2.1.11 | Columnospf3AreaInfoVirtNeighborsFULLstate | read-only | current | Total neighbors in FULL state. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3 | Tableospf3IntfInfoTable | not-accessible | current | The table of OSPFv3 Interface information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1 | Rowospf3IntfInfoEntry | not-accessible | current | Information about a OSPFv3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.1 | Columnospf3IfInfoIndex | read-only | current | The OSPFv3 interface number for which the OSPFv3 info table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.2 | Columnospf3IfInfoInstanceID | read-only | current | The OSPFv3 interface instance id. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.3 | Columnospf3IfInfoLLocalAddress | read-only | current | The IP address of the OSPFv3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.4 | Columnospf3IfInfoAreaID | read-only | current | The AreaID of the area that the interface belongs. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.5 | Columnospf3IfInfoAdminStatus | read-only | current | Admin Status of the interface: down(0), up(1). |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.6 | Columnospf3IfInfoPassive | read-only | current | Passive status of the interface: disabled(0), enabled(1). |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.7 | Columnospf3IfInfoNetworkType | read-only | current | Network type of the interface: broadcast(1),nbma(2),pointToPoint(3),pointToMultipoint(5). |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.8 | Columnospf3IfInfoState | read-only | current | The state of the interface: Down(0), Loopback(1), Waiting(2), P to P(3), DR(4), BackuDR(5), DR Other(6). |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.9 | Columnospf3IfInfoPriority | read-only | current | Interface router priority |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.10 | Columnospf3IfInfoDesignatedRouterID | read-only | current | The OSPFv3 Designated Router ID for this OSPFv3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.11 | Columnospf3IfInfoBackupDesignatedRouterID | read-only | current | The OSPFv3 Backup Designated Router ID for this OSPFv3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.12 | Columnospf3IfInfoHello | read-only | current | The hello timer for this OSPF3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.13 | Columnospf3IfInfoDead | read-only | current | The dead timer for this OSPFv3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.14 | Columnospf3IfInfoPoll | read-only | current | The OSPFv3 Poll interval for this OSPFv3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.15 | Columnospf3IfInfoRetransmit | read-only | current | The retransmit interval for this OSPFv3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.16 | Columnospf3IfInfoTransitDelay | read-only | current | The transit delay for this OSPFv3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.17 | Columnospf3IfInfoTotalNeighbours | read-only | current | The total number of neighbours for this OSPFv3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.18 | Columnospf3IfInfoEvents | read-only | current | The total number of events for this OSPF3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.19 | Columnospf3IfInfoMetricCost | read-only | current | The cost of this OSPF3 interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.20 | Columnospf3IfInfoAuthSpi | read-only | current | Authentication Spi Id(256 - 4294967295) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.21 | Columnospf3IfInfoAuthEnable | read-only | current | Authentication Status disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.22 | Columnospf3IfInfoAuthType | read-only | current | Authentication Type none(0), md5(2), sha1(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.23 | Columnospf3IfInfoAuthKey | read-only | current | Authentication Key Hex-string MD5 key - 32 chars (128 bits) Hex-string SHA-1 key - 40 chars (160 bits) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.24 | Columnospf3IfInfoEncrySpi | read-only | current | Encryption Spi Id(256 - 4294967295) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.25 | Columnospf3IfInfoEncryEnable | read-only | current | Encryption Status disabled(0), enabled(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.26 | Columnospf3IfInfoEncryType | read-only | current | Encryption Authentication Type null(0), 3des(2), aes(3) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.27 | Columnospf3IfInfoEncryKey | read-only | current | Encryption Key Hex-string AES key - 32 chars (128 bits) Hex-string 3DES key - 48 chars (192 bits) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.28 | Columnospf3IfInfoEncryAuthType | read-only | current | Encryption Authentication Type none(0), md5(2), sha1(1) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.29 | Columnospf3IfInfoEncryAuthKey | read-only | current | Encryption Authentication Key Hex-string MD5 key - 32 chars (128 bits) Hex-string SHA-1 key - 40 chars (160 bits) |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.3.1.30 | Columnospf3IfInfoLsaSupress | read-only | current | Lsa supression status of the interface: disabled(0), enabled(1). |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.4 | Tableospf3VirtIntfInfoTable | not-accessible | current | The table of OSPFv3 Virtual Interface information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.4.1 | Rowospf3VirtIntfInfoEntry | not-accessible | current | Information about a single virtual interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.4.1.1 | Columnospf3VirtIfInfoIndex | read-only | current | The OSPFv3 virtual interface number for which the OSPFv3 info table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.4.1.2 | Columnospf3VirtIfInfoAreaId | read-only | current | The transit area that the virtual link traverses. By definition, this is not Area 0. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.4.1.3 | Columnospf3VirtIfInfoNeighbor | read-only | current | The Router ID of the virtual neighbor. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.4.1.5 | Columnospf3VirtIfInfoTransitDelay | read-only | current | The estimated number of seconds it takes to transmit a Link State Update packet over this interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.4.1.6 | Columnospf3VirtIfInfoRetransInterval | read-only | current | The number of seconds between link state advertisement retransmissions for adjacencies belonging to this interface. This value is also used when retransmitting… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.4.1.7 | Columnospf3VirtIfInfoHelloInterval | read-only | current | The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for the virtual neighbor. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.4.1.8 | Columnospf3VirtIfInfoRtrDeadInterval | read-only | current | The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down. This should be some multiple of the Hello … |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.4.1.9 | Columnospf3VirtIfInfoState | read-only | current | OSPF virtual interface states. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.4.1.10 | Columnospf3VirtIfInfoEvents | read-only | current | The number of state changes or error events on this virtual link. Discontinuities in the value of this counter can occur at re-initialization of the management… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.4.1.11 | Columnospf3VirtIfInfoStatus | read-only | current | This object permits management of the table by facilitating actions such as row creation, construction, and destruction. The value of this object has no effect… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.4.1.12 | Columnospf3VirtIfInfoLinkScopeLsaCount | read-only | current | The total number of Link-scope link state advertisements in this virtual link's link state database. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.4.1.13 | Columnospf3VirtIfInfoLinkLsaCksumSum | read-only | current | The 32-bit unsigned sum of the Link-scope link state advertisements' LS checksums contained in this virtual link's link state database. The sum can be used to … |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.5 | Tableospf3IfNbrTable | not-accessible | current | The table of OSPFv3 Interface Neighbor information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.5.1 | Rowospf3IfNbrEntry | not-accessible | current | Information about a OSPFv3 interface, neighbor pair. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.5.1.1 | Columnospf3IfNbrInfoIndex | read-only | current | The OSPFv3 neighbor table entry index for which this table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.5.1.2 | Columnospf3IfNbrIntfIndex | read-only | current | The OSPFv3 Interface number for which this Nbr table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.5.1.3 | Columnospf3IfNbrIntfInstanceID | read-only | current | The OSPFv3 Interface instance id for which this Nbr table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.5.1.4 | Columnospf3IfNbrRtrID | read-only | current | A 32-bit unsigned integer uniquely identifying the neighboring router in the Autonomous System. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.5.1.5 | Columnospf3IfNbrIpAddress | read-only | current | The IPv6 address of the neighbor associated with the local link. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.5.1.6 | Columnospf3IfNbrPriority | read-only | current | The priority of the OSPFv3 neighbor. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.5.1.7 | Columnospf3IfNbrState | read-only | current | The state of the relationship with this neighbor. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.5.1.8 | Columnospf3IfNbrEvents | read-only | current | The number of times this neighbor relationship has changed state or an error has occurred. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.6 | Tableospf3RoutesInfoTable | not-accessible | current | The table of OSPFv3 routes information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.6.1 | Rowospf3RoutesInfoEntry | not-accessible | current | OSPFv3 routes information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.6.1.1 | Columnospf3RoutesInfoIndex | read-only | current | The OSPFv3 route table entry index for which this table is related. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.6.1.2 | Columnospf3RoutesInfoDestination | read-only | current | The Destination IPv6 Address of this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.6.1.3 | Columnospf3RoutesInfoPrefixLen | read-only | current | Indicates the prefix length of the destination Address. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.6.1.4 | Columnospf3RoutesInfoNextHop | read-only | current | Next Hop IPv6 Address for this route. For direct routes it has the value ::0. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.6.1.5 | Columnospf3RoutesInfoType | read-only | current | Type of the route |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.6.1.6 | Columnospf3RoutesInfoAreaId | read-only | current | Area ID associated with the route |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.6.1.7 | Columnospf3RoutesInfoCost | read-only | current | It is a Type 1 external metrics which is expressed in the same units as OSPF interface cost ie. in terms of the OSPF link state metric. If Type1 and Type2 cost… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.6.1.8 | Columnospf3RoutesInfoType2Cost | read-only | current | Type 2 external metrics are configured with the cost greater than any path internal to the AS. Use of Type 2 external metrics assumes that routing between AS i… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.18.6.1.9 | Columnospf3RoutesInfoInterfaceIndex | read-only | current | Interface Index associated with the route |
| 1.3.6.1.4.1.26543.2.7.7.3.3.19 | NodeipEcmpRoutingInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.19.1 | TableipRouteEcmpInfoTable | not-accessible | current | The table of run-time IP routes. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.19.1.1 | RowipRouteEcmpInfoEntry | not-accessible | current | A row in the run-time IP route table |
| 1.3.6.1.4.1.26543.2.7.7.3.3.19.1.1.1 | ColumnipRouteEcmpInfoDestIndx | read-only | current | The index of unique destinations IP. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.19.1.1.2 | ColumnipRouteEcmpInfoGwIndx | read-only | current | The index of the gateway per destination. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.19.1.1.3 | ColumnipRouteEcmpInfoDest | read-only | current | The destination IP of this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.19.1.1.4 | ColumnipRouteEcmpInfoMask | read-only | current | The destination IP mask of this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.19.1.1.5 | ColumnipRouteEcmpInfoGateway | read-only | current | The next-hop router address for this route. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.19.1.1.6 | ColumnipRouteEcmpInfoInterface | read-only | current | The interface for the next-hop. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.19.1.1.7 | ColumnipRouteEcmpInfoGwStatus | read-only | current | The Up/Down status of the gateway |
| 1.3.6.1.4.1.26543.2.7.7.3.3.20 | NodeipEcmpHash | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.20.1 | ScalaripEcmpHashSIPAddr | read-write | current | The SIP Address. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.20.2 | ScalaripEcmpHashDIPAddr | read-write | current | The DIP Address (enter 0 for SIP only). |
| 1.3.6.1.4.1.26543.2.7.7.3.3.20.3 | ScalaripEcmpHashNumberPaths | read-write | current | The number of ECMP paths. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.20.4 | ScalaripEcmpHashRouteNumber | read-only | current | The result of the hash algorithm. For this to work the values for ipEcmpHashSIPAddr, ipEcmpHashDIPAddr, ipEcmpHashNumberPaths must be set. If the result is 0 i… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.21 | Nodeipv6PmtuInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.21.1 | Tableipv6PmtuInfoTable | not-accessible | current | The table of Ipv6 PMTU entries. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.21.1.1 | Rowipv6PmtuInfoEntry | not-accessible | current | A row in the ipv6 PMTU entries table. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.21.1.1.1 | Columnipv6PmtuInfoIndx | read-only | current | The index of this ipv6 PMTU table entries. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.21.1.1.2 | Columnipv6PmtuInfoDestIp | read-only | current | The destination of the pMTU. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.21.1.1.3 | Columnipv6PmtuInfoSinceTime | read-only | current | The addubt time of the pMTU. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.21.1.1.4 | Columnipv6PmtuInfoValue | read-only | current | The vlaue of this ipv6 PMTU table entries. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22 | NodemldInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.1 | TablemldInfoGroupsTable | not-accessible | current | The table listing the IPv6 multicast groups for which there are members on a particular interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.1.1 | RowmldInfoGroupEntry | not-accessible | current | An entry in the mldInfoGroupsTable |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.1.1.1 | ColumnmldInfoGroupIfIndex | read-only | current | The internetwork-layer interface for which this entry contains information for an IPv6 multicast group address. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.1.1.2 | ColumnmldInfoGroupAddress | read-only | current | The IPv6 multicast group address for which this entry contains information. Its address MUST be of format: 2x:2x:2x:2x:2x:2x:2x:2x |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.1.1.3 | ColumnmldInfoGroupPortNumber | read-only | current | The port number for which this entry contains information for an IPv6 multicast group address. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.1.1.4 | ColumnmldInfoGroupVlanID | read-only | current | The VLAN ID for which this entry contains information for an IPv6 multicast group address. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.1.1.5 | ColumnmldInfoGroupLastReporter | read-only | current | The IPv6 address of the source of the last membership report received for this IPv6 Multicast group address on this interface. If no membership report has been… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.1.1.6 | ColumnmldInfoGroupSource | read-only | current | ONLY for MLDv2. The IPv6 address for which the this entry's filter is applied. Its address MUST be of format: 2x:2x:2x:2x:2x:2x:2x:2x |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.1.1.7 | ColumnmldInfoGroupFilterType | read-only | current | ONLY for MLDv2. The filter type for the specified source. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.1.1.8 | ColumnmldInfoGroupExpiryTime | read-only | current | The minimum amount of time remaining before this entry will be aged out. A value of 0 indicates that the entry is only present because mldCacheSelf is true and… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.1.1.9 | ColumnmldInfoGroupVersion | read-only | current | The version of this MLD entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.1.1.10 | ColumnmldInfoGroupFwd | read-only | current | Specifies if forwarding is enabled for this entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.1.1.11 | ColumnmldInfoGroupId | read-only | current | MLD group index. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.2 | TablemldInfoMRoutersTable | not-accessible | current | The table listing the IPv6 multicast routers on an interface. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.2.1 | RowmldInfoMRouterEntry | not-accessible | current | An entry in the mldInfoMRoutersTable |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.2.1.1 | ColumnmldInfoMRouterIfIndex | read-only | current | The interface on which the multicast router is learnt. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.2.1.2 | ColumnmldInfoMRouterSrcIp | read-only | current | The multicast router's ip. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.2.1.3 | ColumnmldInfoMRouterPortNumber | read-only | current | The port on which the multicast router is learnt. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.2.1.4 | ColumnmldInfoMRouterVlan | read-only | current | The vlan in which the multicast router is learnt. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.2.1.5 | ColumnmldInfoMRouterQrv | read-only | current | This multicast router's Maximum Response Delay |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.2.1.6 | ColumnmldInfoMRouterQqic | read-only | current | ONLY for MLDv2. This multicast router's QQIC |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.2.1.7 | ColumnmldInfoMRouterMaxRespDelay | read-only | current | This multicast router's Maximum Response Delay. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.2.1.8 | ColumnmldInfoMRouterVersion | read-only | current | This multicast router's MLD version. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.2.1.9 | ColumnmldInfoMRouterExpiryTime | read-only | current | This multicast router's expiry time. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.2.1.10 | ColumnmldInfoMRouterId | read-only | current | This multicast router's index. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.3 | ScalarmldClearTables | read-write | current | Clear the MLD tables. When setting clearGroups(1), the dynamic groups are removed, when setting clearMrouters(2), the mrouter tables are removed and when setti… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.4 | TablemldInfoInterfaceTable | not-accessible | current | The (conceptual) table listing the informatio of interfaces on which MLD is enabled. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.4.1 | RowmldInfoInterfaceEntry | not-accessible | current | An entry (conceptual row) representing the information of an interface on which MLD is enabled. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.4.1.1 | ColumnmldInfoInterfaceIfIndex | read-only | current | The internetwork-layer interface value of the interface for which MLD is enabled. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.4.1.2 | ColumnmldInfoInterfaceState | read-only | current | The internetwork-layer interface value of the interface for which MLD is enabled. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.4.1.3 | ColumnmldInfoInterfaceVersion | read-only | current | The version of MLD which is running on this interface. This object is a place holder to allow for new versions of MLD to be introduced. Version 1 of MLD is def… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.4.1.4 | ColumnmldInfoInterfaceQuerierStatus | read-only | current | Specifies if the switch is Querier or not |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.4.1.5 | ColumnmldInfoInterfaceQuerier | read-only | current | The address of the MLD Querier on the IPv6 subnet to which this interface is attached. Its address MUST be of format:2x:2x:2x:2x:2x:2x:2x:2x |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.4.1.6 | ColumnmldInfoInterfaceQuerierExpiryTime | read-only | current | The time remaining before the Other Querier Present Timer expires. If the local system is the querier, the value of this object is zero. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.4.1.7 | ColumnmldInfoInterfaceQuerierPortIndex | read-only | current | The port on which the Querier is learnt. If the local system is the querier, the value of this object is zero. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.22.4.1.8 | ColumnmldInfoInterfaceGroups | read-only | current | The current number of entries for this interface in the Cache Table. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23 | NodeipsecInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.1 | TableipsecSaInfoTable | not-accessible | current | The (conceptual) table listing all of the IPsec SA information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.1.1 | RowipsecSaInfoEntry | not-accessible | current | An entry (conceptual row) representing a IPsec SA information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.1.1.1 | ColumnipsecSaInfoIndex | read-only | current | The index of ipsecSaInfoEntry. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.1.1.2 | ColumnipsecSaInfoSpi | read-only | current | The SPI used by the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.1.1.3 | ColumnipsecSaInfoProto | read-only | current | The proto(AH,ESP,or Both) used by the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.1.1.4 | ColumnipsecSaInfoDstAddr | read-only | current | The destination IP address for the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.1.1.5 | ColumnipsecSaInfoSrcAddr | read-only | current | The source IP address for the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.1.1.6 | ColumnipsecSaInfoFlags | read-only | current | The direction, initiator and etc for an SA; see flag constants below: SA_FLAG_INUSE 0x0001 SA_FLAG_DELETED 0x0002 SA_FLAG_INBOUND 0x0004 SA_FLAG_INITIATOR 0x00… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.1.1.7 | ColumnipsecSaInfoUlp | read-only | current | The upper layer protocol for an SA; 0=any; see protocol constants below: ICMP 1 IPv4 4 TCP 6 UDP 17 ESP 50 AH 51 IPv6 41 ICMPv6 58 |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.1.1.8 | ColumnipsecSaInfoMode | read-only | current | The mode for the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.1.1.9 | ColumnipsecSaInfoAuthAlg | read-only | current | The authentication algorithm for the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.1.1.10 | ColumnipsecSaInfoAuthKey | read-only | current | The authentication key for the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.1.1.11 | ColumnipsecSaInfoEncrAlg | read-only | current | The encryption algorithm for the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.1.1.12 | ColumnipsecSaInfoEncrKey | read-only | current | The encryption key for the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.2 | TableipsecSpdInfoTable | not-accessible | current | The (conceptual) table listing all of the IPsec security policy information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.2.1 | RowipsecSpdInfoEntry | not-accessible | current | An entry (conceptual row) representing a IPsec security policy information. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.2.1.1 | ColumnipsecSpdInfoIndex | read-only | current | The index of ipsecSpdInfoEntry. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.2.1.2 | ColumnipsecSpdInfoFlags | read-only | current | The direction, initiator and etc for an SA; see flag constants below: SP_FLAG_INUSE 0x00000001 SP_FLAG_DELETED 0x00000002 SP_FLAG_INBOUND 0x00000004 SP_FLAG_MI… |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.2.1.3 | ColumnipsecSpdInfoULP | read-only | current | The transport layer protocol for the SA. 0 = any. see protocol constants below: ICMP 1 IPv4 4 TCP 6 UDP 17 ESP 50 AH 51 IPv6 41 ICMPv6 58 |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.2.1.4 | ColumnipsecSpdInfoAction | read-only | current | The IPsec action for the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.2.1.5 | ColumnipsecSpdInfoDstAddr | read-only | current | The destination IP address for the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.2.1.6 | ColumnipsecSpdInfoSrcAddr | read-only | current | The source IP address for the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.2.1.7 | ColumnipsecSpdInfoMode | read-only | current | The mode for the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.2.1.8 | ColumnipsecSpdInfoSaSize | read-only | current | The SA bundle size of an Security policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.3 | TableipsecSpdInfoSaTable | not-accessible | current | The (conceptual) table listing all information of the SA nested in an IPsec security policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.3.1 | RowipsecSpdInfoSaEntry | not-accessible | current | An entry (conceptual row) representing a SA information netsted in an IPsec security policy. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.3.1.1 | ColumnipsecSpdInfoSaIndex | read-only | current | The index that enumerates the IPsec nested SAs . |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.3.1.2 | ColumnipsecSpdInfoSaSecuProto | read-only | current | The security protocol for the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.3.1.3 | ColumnipsecSpdInfoSaAuthAlg | read-only | current | The hash algorithm used by the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.3.1.4 | ColumnipsecSpdInfoSaEncrAlg | read-only | current | The encryption algorithm used by the SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.23.3.1.5 | ColumnipsecSpdInfoSaEncrKeyLen | read-only | current | The encryption key length of an nested SA. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.24 | NodedhcpsnpInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.3.3.24.1 | TabledhcpSnoopingBindingInfoTable | not-accessible | current | DHCP Snooping binding Table. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.24.1.1 | RowdhcpSnoopingBindingInfoEntry | not-accessible | current | A row in the DHCP Snooping binding Table |
| 1.3.6.1.4.1.26543.2.7.7.3.3.24.1.1.1 | ColumndhcpSnoopingBindingInfoIndex | read-only | current | Index of this DHCP Snooping binding entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.24.1.1.2 | ColumndhcpSnoopingBindingInfoMac | read-create | current | Mac Address of this DHCP Snooping binding entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.24.1.1.3 | ColumndhcpSnoopingBindingInfoIp | read-write | current | Ip Address of this DHCP Snooping binding entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.24.1.1.4 | ColumndhcpSnoopingBindingInfoVLAN | read-write | current | VLAN ID of this DHCP Snooping binding entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.24.1.1.5 | ColumndhcpSnoopingBindingInfoPortIndex | read-write | current | Port Number of this DHCP Snooping binding entry. |
| 1.3.6.1.4.1.26543.2.7.7.3.3.24.1.1.6 | ColumndhcpSnoopingBindingInfoExpiry | read-write | current | The lease time of this DHCP Snooping binding entry. Set 0 to remove this entry |
| 1.3.6.1.4.1.26543.2.7.7.3.3.24.1.1.7 | ColumndhcpSnoopingBindingInfoType | read-write | current | Show How this DHCP Snooping binding entry come from. |
| 1.3.6.1.4.1.26543.2.7.7.3.4 | Nodelayer3Oper | |||
| 1.3.6.1.4.1.26543.2.7.7.3.4.1 | NodevrrpOper | |||
| 1.3.6.1.4.1.26543.2.7.7.3.4.1.1 | TablevrrpOperVirtRtrTable | not-accessible | current | An entry in the table of virtual routers. |
| 1.3.6.1.4.1.26543.2.7.7.3.4.1.1.1 | RowvrrpOperVirtRtrEntry | not-accessible | current | A row in the vrrpOperVirtRtrTable |
| 1.3.6.1.4.1.26543.2.7.7.3.4.1.1.1.1 | ColumnvrrpOperVirtRtrIndex | read-only | current | The index for the VRRP virtual router. |
| 1.3.6.1.4.1.26543.2.7.7.3.4.1.1.1.2 | ColumnvrrpOperVirtRtrBackup | read-write | current | When set to a value of 'backup(2)' it forces the specified master virtual router into backup mode. 'ok(1)' is returned when the object is read. |
| 1.3.6.1.4.1.26543.2.7.7.3.4.1.2 | ScalarvrrpOperVirtRtrGroupBackup | read-write | current | When set to a value of 'backup(2)' it forces the specified master virtual router group into backup mode. 'ok(1)' is returned when the object os read. |
| 1.3.6.1.4.1.26543.2.7.7.7 | Nodetraps | |||
| 1.3.6.1.4.1.26543.2.7.7.7.0 | NodeibmSNMPv2Notifications | |||
| 1.3.6.1.4.1.26543.2.7.7.7.0.1 | NotificationswPrimaryPowerSupplyFailureNotify | current | A swPrimaryPowerSupplyFailure trap signifies that the primary power supply failed. | |
| 1.3.6.1.4.1.26543.2.7.7.7.0.97 | NotificationswPrimaryPowerSupplyFixedNotify | current | A swPrimaryPowerSupplyFixed trap signifies that the primary power supply has been restored. | |
| 1.3.6.1.4.1.26543.2.7.7.7.1 | NodeswPrimaryPowerSupplyFailure | A swPrimaryPowerSupplyFailure trap signifies that the primary power supply failed. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.2 | NodeswDefGwUp | A swDefGwUp trap signifies that the default gateway is alive. ipCurCfgGwIndex is the index of the Gateway in ipCurCfgGwTable. The range for ipCurCfgGwIndex is … | ||
| 1.3.6.1.4.1.26543.2.7.7.7.3 | NodeswDefGwDown | A swDefGwDown trap signifies that the default gateway is down. ipCurCfgGwIndex is the index of the Gateway in ipCurCfgGwTable. The range for ipCurCfgGwIndex is… | ||
| 1.3.6.1.4.1.26543.2.7.7.7.4 | NodeswDefGwInService | A swDefGwInService trap signifies that the default gateway is up and in service. ipCurCfgGwIndex is the index of the Gateway in ipCurCfgGwTable. The range for … | ||
| 1.3.6.1.4.1.26543.2.7.7.7.5 | NodeswDefGwNotInService | A swDefGwNotInService trap signifies that the default gateway is alive but not in service. ipCurCfgGwIndex is the index of the Gateway in ipCurCfgGwTable. The … | ||
| 1.3.6.1.4.1.26543.2.7.7.7.19 | NodeswLoginFailure | A swLoginFailure trap signifies that someone failed to enter a valid username/password combination. swTrapDisplayString specifies whether the login attempt was… | ||
| 1.3.6.1.4.1.26543.2.7.7.7.22 | NodeswTempExceedThreshold | A swTempExceedThreshold trap signifies that the switch temperature has exceeded maximum safety limits. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.24 | NodeswFanFailure | A swFanFailure trap signifies that the fan failure has been detected. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.25 | NodeswValidLogin | A swValidLogin trap signifies that a user login has occured. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.27 | NodeswApplyComplete | A swApplyComplete signifies that new configuration has been applied. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.28 | NodeswSaveComplete | A swApplyComplete signifies that new configuration has been saved. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.29 | NodeswFwDownloadSucess | A swFwDownloadSuccess signifies that firmware has been downloaded to [image1|image2|boot image]. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.30 | NodeswFwDownloadFailure | A swFwDownloadFailure signifies that firmware downloaded failed to [image1|image2|boot image]. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.31 | NodeswTempReturnThreshold | A swTempReturnThreshold trap signifies that the switch temperature has returned below maximum safety limits. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.33 | NodeswFanFailureFixed | A swFanFailureFixed trap signifies that the fan failure has been fixed. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.42 | NodeswStgNewRoot | A swStgNewRoot trap signifies that the bridge has become the new root of the STG. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.43 | NodeswCistNewRoot | A swCistNewRoot trap signifies that the bridge has become the new root of the CIST. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.44 | NodeswStgTopologyChanged | A swStgTopologyChanged trap signifies that there was a STG topology change. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.45 | NodeswCistTopologyChanged | A swCistTopologyChanged trap signifies that there was a CIST topology change. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.46 | NodeswHotlinksMasterUp | A swHotlinksMasterUp trap signifies that the Master interface is active. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.47 | NodeswHotlinksMasterDn | A swHotlinksMasterDn trap signifies that the Master interface is not active. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.48 | NodeswHotlinksBackupUp | A swHotlinksBackupUp trap signifies that the Backup interface is active. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.49 | NodeswHotlinksBackupDn | A swHotlinksBackupDn trap signifies that the Backup interface is not active. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.50 | NodeswHotlinksNone | A swHotlinksNone trap signifies that there are no active interfaces. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.51 | NodesfpInserted | A sfpInserted trap signifies that a SFP is inserted. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.52 | NodesfpRemoved | A sfpRemoved trap signifies that a SFP is removed. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.61 | NodeswNTPSyncFailed | A swNTPSyncFailed trap signifies that sync with NTP server failed. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.62 | NodeswNTPUpdateClock | A swNTPUpdateClock trap signifies that update system clock with NTP server. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.63 | NodeswValidLogout | A swValidLogout trap signifies that a user logout has occured. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.65 | NodeswECMPGatewayUp | A swECMPGatewayUp trap signifies that the ECMP gateway is up. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.66 | NodeswECMPGatewayDown | A swECMPGatewayDown trap signifies that the ECMP gateway is down. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.67 | NodeswTeamingCtrlUp | A swTeamingCtrlUp trap signifies that the teaming is up. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.68 | NodeswTeamingCtrlDown | A swTeamingCtrlDown trap signifies that the teaming control is down. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.69 | NodeswTeamingCtrlDownTearDownBlked | A swTeamingCtrlDownTearDownBlked trap signifies that the teaming control is down but teardown is blocked. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.70 | NodeswTeamingCtrlError | A swTeamingCtrlError trap signifies error, action is undefined. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.71 | NodeswLACPPortBlocked | A swLACPPortBlocked trap signifies that LACP is operationally down on a port, and traffic is blocked on the port. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.72 | NodeswLACPPortUnblocked | A swLACPPortUnblocked trap signifies that LACP is operationally up on a port, and traffic is no longer blocked on the port. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.77 | NodeswVMGroupVMotion | A altVMGroupVMotion trap signifies that a virtual machine has moved from a port to another. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.78 | NodeswVMGroupVMOnline | A altVMGroupVMOnline trap signifies that a advance provisioned virtual machine has came online. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.79 | NodeswVMGroupVMVlanChange | A altVMGroupVMVlanChange trap signifies that a virtual machine has entered into a vlan, or changed the vlan. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.97 | NodeswPrimaryPowerSupplyFixed | A swPrimaryPowerSupplyFixed trap signifies that the primary power supply has been restored. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.103 | NodeswLFDPortErrdisabled | An swLFDPortErrdisabled trap signifies that a port is error-disabled due to excessive link flaps. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.106 | NodeswVlagInstanceUp | A swVlagInstanceUp trap signifies that vLAG instance is up identified in the trap message. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.107 | NodeswVlagInstanceRemoteUp | A swVlagInstanceRemoteUp trap signifies that vLAG is down but remote instance is Up. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.108 | NodeswVlagInstanceLocalUp | A swVlagInstanceLocalUp trap signifies that vLAG is down but local instance is Up. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.109 | NodeswVlagInstanceDown | A swVlagInstanceDown trap signifies that vLAG instance is down identified in the trap message. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.110 | NodeswVlagIslUp | A swVlagIslUp trap signifies that connection between vLAG switches is up. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.111 | NodeswVlagIslDown | A swVlagInstanceDown trap signifies that connection between vLAG switches is down. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.144 | NodeswOflowConnectControllerFailure | A swOflowConnectControllerFailure trap signifies that the connection to openflow controller is broken. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.145 | NodeswOflowConnectControllerSuccess | A swOflowConnectControllerSuccess trap signifies that the connection to openflow controller is successful. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.146 | NodeswOflowEmergencyState | A swOflowEmergencyState trap signifies that the openflow switch moving to emergency state. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.147 | NodeswOflowNoEmergencyState | A swOflowNoEmergencyState trap signifies that the openflow switch came out of emergency state. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.148 | NodeswOflowSwitchOflowMode | A swOflowSwitchOflowMode trap signifies that the device working in openflow switch mode. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.149 | NodeswOflowSwitcNormalMode | A swOflowSwitcNormalMode trap signifies that the device working in normal switch mode. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.150 | NodeswOflowSwitcFlowtableClr | A swOflowSwitcFlowtableClr trap signifies that the flow table entries being cleared from the device. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.151 | NodeswOflowSwitcStatsClr | A swOflowSwitcStatsClr trap signifies that the openflow statistics being cleared from the device. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.152 | NodeswOflowFlowtableEntryUnavail | A swOflowFlowtableMemoryUnavail trap signifies that the device unable to add flow entry in openflow due to unavailability of system resources. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.153 | NodeswOflowFlowtableLimit | A swOflowFlowtableLimit trap signifies that the device reaches its configured flow limit. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.154 | NodeswOflowPortDownController | A swOflowPortDownController trap signifies that the port operationally down by openflow controller. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.155 | NodeswOflowPortUpController | A swOflowPortUpController trap signifies that the port operationally up by openflow controller. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.156 | NodeswOflowVersionNegotiationError | A swOflowVersionNegotiationError trap signifies that the device unable to connect to controller either due to bad version, or negotiation/hello failure. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.158 | Nodesw8021x | A sw8021x trap is sent when dot1x feature is enabled. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.162 | NodeswDefAdminDisable | A swDefAdminDisable trap signifies that default admin account has been disabled. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.163 | NodeswAcntStrngPswdNotMet | A swAcntStrngPswdNotMet trap signifies that configured password does not match strong password complexity. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.164 | NodeswAcntLocked | A swAcntLocked trap signifies that account has been locked. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.165 | NodeswAcntUnlocked | A swAcntUnlocked trap signifies that account has been unlocked. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.184 | NodeswARPtablefull | A swARPtablefull trap signifies that ARP table is full. | ||
| 1.3.6.1.4.1.26543.2.7.7.7.1000 | ScalarswTrapDisplayString | read-only | current | Temporary string object used to store information being sent in a Switch trap. |
| 1.3.6.1.4.1.26543.2.7.7.8 | Nodeqos | |||
| 1.3.6.1.4.1.26543.2.7.7.8.1 | NodeqosConfig | |||
| 1.3.6.1.4.1.26543.2.7.7.8.1.1 | Nodeqos8021p | |||
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.1 | TableqosCurCfgPortPriorityTable | not-accessible | current | The table of QOS Port Priority configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.1.1 | RowqosCurCfgPortPriorityEntry | not-accessible | current | Information about a particular QOS Port Priority configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.1.1.1 | ColumnqosCurCfgPortIndex | read-only | current | Switch Port Number |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.1.1.2 | ColumnqosCurCfgPortPriority | read-only | current | Switch Port Priority Should be between 0 and 7 |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.2 | TableqosNewCfgPortPriorityTable | not-accessible | current | The table of QOS Port Priority configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.2.1 | RowqosNewCfgPortPriorityEntry | not-accessible | current | Information about a particular QOS Port Priority configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.2.1.1 | ColumnqosNewCfgPortIndex | read-only | current | Switch Port Number |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.2.1.2 | ColumnqosNewCfgPortPriority | read-write | current | Switch Port Priority Should be between 0 and 7 |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.3 | TableqosCurCfgPriorityCoSTable | not-accessible | current | The table of Frame Priority and COSq configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.3.1 | RowqosCurCfgPriorityCoSEntry | not-accessible | current | Information about a particular Frame Priority and COSq configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.3.1.1 | ColumnqosCurCfgPriorityIndex | read-only | current | Frame priority Number |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.3.1.2 | ColumnqosCurCfgPriorityCoSq | read-only | current | CoSq for a Frame Priority Should be between 0 and 7 |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.4 | TableqosNewCfgPriorityCoSTable | not-accessible | current | The table of Frame Priority and COSq configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.4.1 | RowqosNewCfgPriorityCoSEntry | not-accessible | current | Information about a particular Frame Priority and COSq configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.4.1.1 | ColumnqosNewCfgPriorityIndex | read-only | current | Frame priority Number |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.4.1.2 | ColumnqosNewCfgPriorityCoSq | read-write | current | CoSq for a Frame Priority Should be between 0 and 7 |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.5 | TableqosCurCfgCosWeightTable | not-accessible | current | The table of CoSq and Weight configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.5.1 | RowqosCurCfgCosWeightEntry | not-accessible | current | Information about a particular CoSq and Weight configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.5.1.1 | ColumnqosCurCfgCosIndex | read-only | current | CoSq Number |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.5.1.2 | ColumnqosCurCfgCosWeight | read-only | current | Weight of CoSq |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.6 | TableqosNewCfgCosWeightTable | not-accessible | current | The table of CoSq and Weight configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.6.1 | RowqosNewCfgCosWeightEntry | not-accessible | current | Information about a particular CoSq and Weight configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.6.1.1 | ColumnqosNewCfgCosIndex | read-only | current | CoSq Number |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.6.1.2 | ColumnqosNewCfgCosWeight | read-write | current | Weight of CoSq |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.7 | ScalarqosCurCfgCosNum | read-only | current | Number of CoSq. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.8 | ScalarqosNewCfgCosNum | read-write | current | Number of CoSq. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.1.9 | ScalarqosDefaultCfg | read-write | current | Load default configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.2 | Nodeqosdscp | |||
| 1.3.6.1.4.1.26543.2.7.7.8.1.2.1 | TableqosCurCfgDscpTable | not-accessible | current | The table of Dscp to New Dscp/802.1p priority configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.2.1.1 | RowqosCurCfgDscpEntry | not-accessible | current | Information about a particular Dscp to New Dscp/802.1p priority configuration |
| 1.3.6.1.4.1.26543.2.7.7.8.1.2.1.1.1 | ColumnqosCurCfgDscpIndex | read-only | current | Dscp value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.2.1.1.2 | ColumnqosCurCfgMapDscp | read-only | current | Map Dscp Value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.2.1.1.3 | ColumnqosCurCfgMap8021p | read-only | current | Map 802.1p value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.2.2 | TableqosNewCfgDscpTable | not-accessible | current | The table of Dscp to New Dscp/802.1p priority configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.2.2.1 | RowqosNewCfgDscpEntry | not-accessible | current | Information about a particular Dscp to New Dscp/802.1p priority configuration |
| 1.3.6.1.4.1.26543.2.7.7.8.1.2.2.1.1 | ColumnqosNewCfgDscpIndex | read-only | current | Dscp value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.2.2.1.2 | ColumnqosNewCfgMapDscp | read-write | current | Map Dscp Value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.2.2.1.3 | ColumnqosNewCfgMap8021p | read-write | current | Map 802.1p value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.2.3 | ScalarqosCurCfgDscpState | read-only | current | This is for turning on/off DSCP globally. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.2.4 | ScalarqosNewCfgDscpState | read-write | current | This is for turning on/off DSCP globally. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3 | Nodeqoswredecn | |||
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.1 | TableqosCurCfgPortProfileTable | not-accessible | current | The table of QOS port WRED ECN profile configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.1.1 | RowqoSCurCfgPortProfileEntry | not-accessible | current | Information about a particular Transmit queue of a port WRED ECN profile configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.1.1.1 | ColumnqosCurCfgProfilePortIndex | read-only | current | Switch Port Number |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.1.1.2 | ColumnqosCurCfgTrqIndex | read-only | current | Transmit Queue Number |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.1.1.3 | ColumnqosCurCfgTrqNonTcpMin | read-only | current | Port Transmit queue WRED ECN nontcp profile MinThreshold value. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.1.1.4 | ColumnqosCurCfgTrqNonTcpMax | read-only | current | Port Transmit queue WRED ECN nontcp profile MaxThreshold value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.1.1.5 | ColumnqosCurCfgTrqNonTcpRate | read-only | current | Port Transmit queue WRED ECN nontcp profile DropRate value. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.1.1.6 | ColumnqosCurCfgTrqTcpMin | read-only | current | Port Transmit queue WRED ECN tcp profile MinThreshold value. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.1.1.7 | ColumnqosCurCfgTrqTcpMax | read-only | current | Port Transmit queue WRED ECN tcp profile MaxThreshold value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.1.1.8 | ColumnqosCurCfgTrqTcpRate | read-only | current | Port Transmit queue WRED ECN tcp profile DropRate value. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.1.1.9 | ColumnqosCurCfgPortTrqWredState | read-only | current | This is for turning on/off WRED per transmit queue per port. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.2 | TableqosNewCfgPortProfileTable | not-accessible | current | The table of QOS Port WRED ECN configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.2.1 | RowqoSNewCfgPortProfileEntry | not-accessible | current | Information about a particular Transmit queue of a port WRED ECN configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.2.1.1 | ColumnqosNewCfgProfilePortIndex | read-only | current | Switch Port Number |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.2.1.2 | ColumnqosNewCfgTrqIndex | read-only | current | Transmit Queue Number |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.2.1.3 | ColumnqosNewCfgTrqNonTcpMin | read-write | current | Port Transmit queue WRED ECN nontcp profile MinThreshold value. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.2.1.4 | ColumnqosNewCfgTrqNonTcpMax | read-write | current | Port Transmit queue WRED ECN nontcp profile MaxThreshold value. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.2.1.5 | ColumnqosNewCfgTrqNonTcpRate | read-write | current | Port Transmit queue WRED ECN nontcp profile DropRate value. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.2.1.6 | ColumnqosNewCfgTrqTcpMin | read-write | current | Port Transmit queue WRED ECN tcp profile MinThreshold value. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.2.1.7 | ColumnqosNewCfgTrqTcpMax | read-write | current | Port Transmit queue WRED ECN tcp profile MaxThreshold value. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.2.1.8 | ColumnqosNewCfgTrqTcpRate | read-write | current | Port Transmit queue WRED ECN tcp profile DropRate value. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.2.1.9 | ColumnqosNewCfgPortTrqWredState | read-write | current | This is for turning on/off WRED per transmit queue per port. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.3 | TableqosCurCfgPortStateTable | not-accessible | current | The table of QOS port WRED ECN state configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.3.1 | RowqoSCurCfgPortStateEntry | not-accessible | current | Information about a particular port WRED ECN state configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.3.1.1 | ColumnqosCurCfgStatePortIndex | read-only | current | Switch Port Number |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.3.1.2 | ColumnqosCurCfgPortWredState | read-only | current | This is for turning on/off WRED per port. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.3.1.3 | ColumnqosCurCfgPortEcnState | read-only | current | This is for turning on/off ECN per port. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.4 | TableqosNewCfgPortStateTable | not-accessible | current | The table of QOS port WRED ECN state configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.4.1 | RowqoSNewCfgPortStateEntry | not-accessible | current | Information about a particular port WRED ECN state configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.4.1.1 | ColumnqosNewCfgStatePortIndex | read-only | current | Switch Port Number |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.4.1.2 | ColumnqosNewCfgPortWredState | read-write | current | This is for turning on/off WRED per port |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.4.1.3 | ColumnqosNewCfgPortEcnState | read-write | current | This is for turning on/off ECN per port. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.5 | TableqosCurCfgGlobalProfileTable | not-accessible | current | The table of QOS global WRED ECN profile configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.5.1 | RowqoSCurCfgGlobalProfileEntry | not-accessible | current | Information about a particular Transmit queue of global WRED ECN profile configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.5.1.1 | ColumnqosCurCfgGlobalTrqIndex | read-only | current | Global Transmit Queue Number |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.5.1.2 | ColumnqosCurCfgGlobalTrqNonTcpMin | read-only | current | Global transmit queue WRED ECN nontcp profile MinThreshold value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.5.1.3 | ColumnqosCurCfgGlobalTrqNonTcpMax | read-only | current | Global transmit queue WRED ECN nontcp profile MaxThreshold value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.5.1.4 | ColumnqosCurCfgGlobalTrqNonTcpRate | read-only | current | Global transmit queue WRED ECN nontcp profile DropRate value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.5.1.5 | ColumnqosCurCfgGlobalTrqTcpMin | read-only | current | Global transmit queue WRED ECN tcp profile MinThreshold value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.5.1.6 | ColumnqosCurCfgGlobalTrqTcpMax | read-only | current | Global transmit queue WRED ECN tcp profile MaxThreshold value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.5.1.7 | ColumnqosCurCfgGlobalTrqTcpRate | read-only | current | Global transmit queue WRED ECN tcp profile DropRate value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.5.1.8 | ColumnqosCurCfgGlobalTrqWredState | read-only | current | This is for turning on/off WRED per global transmit queue |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.6 | TableqosNewCfgGlobalProfileTable | not-accessible | current | The table of QOS global WRED ECN profile configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.6.1 | RowqoSNewCfgGlobalProfileEntry | not-accessible | current | Information about a particular Transmit queue of global WRED ECN profile configuration. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.6.1.1 | ColumnqosNewCfgGlobalTrqIndex | read-only | current | Global Transmit Queue Number |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.6.1.2 | ColumnqosNewCfgGlobalTrqNonTcpMin | read-write | current | Global transmit queue WRED ECN nontcp profile MinThreshold value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.6.1.3 | ColumnqosNewCfgGlobalTrqNonTcpMax | read-write | current | Global transmit queue WRED ECN nontcp profile MaxThreshold value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.6.1.4 | ColumnqosNewCfgGlobalTrqNonTcpRate | read-write | current | Global transmit queue WRED ECN nontcp profile DropRate value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.6.1.5 | ColumnqosNewCfgGlobalTrqTcpMin | read-write | current | Global transmit queue WRED ECN tcp profile MinThreshold value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.6.1.6 | ColumnqosNewCfgGlobalTrqTcpMax | read-write | current | Global transmit queue WRED ECN tcp profile MaxThreshold value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.6.1.7 | ColumnqosNewCfgGlobalTrqTcpRate | read-write | current | Global transmit queue WRED ECN tcp profile DropRate value |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.6.1.8 | ColumnqosNewCfgGlobalTrqWredState | read-write | current | This is for turning on/off WRED per global transmit queue |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.7 | ScalarqosCurCfgGlobalWredState | read-only | current | This is for turning on/off WRED globally. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.8 | ScalarqosCurCfgGlobalEcnState | read-only | current | This is for turning on/off ECN globally. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.9 | ScalarqosNewCfgGlobalWredState | read-write | current | This is for turning on/off WRED globally. |
| 1.3.6.1.4.1.26543.2.7.7.8.1.3.10 | ScalarqosNewCfgGlobalEcnState | read-write | current | This is for turning on/off ECN globally. |
| 1.3.6.1.4.1.26543.2.7.7.9 | Nodeacl | |||
| 1.3.6.1.4.1.26543.2.7.7.9.1 | NodeacConfig | |||
| 1.3.6.1.4.1.26543.2.7.7.9.1.1 | NodeacList | |||
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1 | TableaclCurCfgTable | not-accessible | current | The table of current ACL configuration. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1 | RowaclCurCfgEntry | not-accessible | current | Current information about a particular ACL configuration entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.1 | ColumnaclCurCfgIndex | read-only | current | The index associated with this ACL entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.3 | ColumnaclCurCfgGroup | read-only | current | The index of the ACL group to which this ACL entry is a member of. A value of zero means the ACL is not a member of any group. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.4 | ColumnaclCurCfgFilterAction | read-only | current | The action to be performed on a packet that matches the filter settings of this ACL entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.5 | ColumnaclCurCfgFilterActionSetPrio | read-only | current | The value to be used when the action to be performed is setprio for this ACL entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.6 | ColumnaclCurCfgEthFmt | read-only | current | The packet ethernet format to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.7 | ColumnaclCurCfgTagFmt | read-only | current | The packet tag format to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.8 | ColumnaclCurCfgIPFmt | read-only | current | The packet IP format to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.9 | ColumnaclCurCfgSrcMACAddress | read-only | current | The source MAC address to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.10 | ColumnaclCurCfgSrcMACMask | read-only | current | The address mask applied to aclCurCfgSrcMACAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.11 | ColumnaclCurCfgDstMACAddress | read-only | current | The destination MAC address to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.12 | ColumnaclCurCfgDstMACMask | read-only | current | The address mask applied to aclCurCfgDstMACAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.13 | ColumnaclCurCfgEthernetTypeName | read-only | current | The Ethernet type to be filtered. If the value of this object is other(7), the value of aclNewCfgEthernetTypeValue indicates the ethernet type that will be fil… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.14 | ColumnaclCurCfgEthernetTypeValue | read-only | current | The Ethernet type value to be filtered. The value of this object is equivalent to the value of aclNewCfgEthernetTypeName except when the value of aclNewCfgEthe… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.15 | ColumnaclCurCfgVLanId | read-only | current | The virtual LAN identifier to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.16 | ColumnaclCurCfgVLanMask | read-only | current | The mask applied to aclCurCfgVLanId for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.17 | ColumnaclCurCfg8021pPriority | read-only | current | The 802.1p priority to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.18 | ColumnaclCurCfgTypeOfService | read-only | current | The type of service to be filtered. 'none' for not initialised, within the range 0-255 |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.19 | ColumnaclCurCfgProtocol | read-only | current | The protocol to be filtered. 'none' for not initialised, within the range 0-255 |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.20 | ColumnaclCurCfgSrcIPAddress | read-only | current | The source IP address to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.21 | ColumnaclCurCfgSrcIPMask | read-only | current | The address mask applied to aclCurCfgSrcIPAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.22 | ColumnaclCurCfgDstIPAddress | read-only | current | The destination IP address to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.23 | ColumnaclCurCfgDstIPMask | read-only | current | The address mask applied to aclCurCfgDstIPAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.24 | ColumnaclCurCfgSrcPort | read-only | current | The source TCP/UDP port number to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.25 | ColumnaclCurCfgSrcPortMask | read-only | current | The mask applied to aclCurCfgSrcPort for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.26 | ColumnaclCurCfgDstPort | read-only | current | The destination TCP/UDP port number to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.27 | ColumnaclCurCfgDstPortMask | read-only | current | The mask applied to aclCurCfgDstPort for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.28 | ColumnaclCurCfgTCPFlags | read-only | current | The TCP flags to be filtered. OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|__tcpSYN(6) |||| ||||_____tcpACK(3) |||______tcpURG(2) ||_______reserved2(1) |_… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.29 | ColumnaclCurCfgEgressPortIndexes | read-only | current | The port list in the ACL configured for egress filtering. The ports are presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... |… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.30 | ColumnaclCurCfgStatistics | read-only | current | Whether statistics collection for this ACL is enabled or not. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.39 | ColumnaclCurCfgTCPFlagsMask | read-only | current | The TCP flags mask. OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|__tcpSYN(6) |||| ||||_____tcpACK(3) |||______tcpURG(2) ||_______reserved2(1) |________res… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.41 | ColumnaclCurCfgMeterAction | read-only | current | Meter Action for this ACL. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.42 | ColumnaclCurCfgMeterEnable | read-only | current | Meter state for this ACL. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.43 | ColumnaclCurCfgKbitsSec | read-only | current | The commited rate of meter associated with this ACL entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.44 | ColumnaclCurCfgKbitsBurst | read-only | current | The maxmium burst sizeof meter associated with this ACL entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.45 | ColumnaclCurCfgUser | read-only | current | Set user defined priority for this ACL. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.46 | ColumnaclCurCfgInprofDscp | read-only | current | Set in profile pkts DSCP value. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.47 | ColumnaclCurCfgTos | read-only | current | To enable/disable setting pkts based on TOS bits. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.48 | ColumnaclCurCfgOutprofDscp | read-only | current | Set out profile pkts DSCP value. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.49 | ColumnaclCurCfgUserEnable | read-only | current | Set update method for this ACL. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.50 | ColumnaclCurCfgInprofDscpEnable | read-only | current | Whether in profile update DSCP for this ACL is enabled or not. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.51 | ColumnaclCurCfgOutprofDscpEnable | read-only | current | Whether out profile update DSCP for this ACL is enabled or not. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.74 | ColumnaclCurCfgMirrorPortIndex | read-only | current | Set port in the ACL for mirroring. n > 0 - the represented port is configured for mirroring. 0 - the represented port is not configured for mirroring. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.1.1.81 | ColumnaclCurCfgLog | read-only | current | Whether log for this ACL is enabled or not. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2 | TableaclNewCfgTable | not-accessible | current | The table of new ACL configuration. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1 | RowaclNewCfgEntry | not-accessible | current | New information about a particular ACL configuration. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.1 | ColumnaclNewCfgIndex | read-only | current | The index associated with this ACL entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.3 | ColumnaclNewCfgGroup | read-only | current | The index of the ACL group to which this ACL entry is a member of. A value of zero means the ACL is not a member of any group. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.4 | ColumnaclNewCfgFilterAction | read-write | current | The action to be performed on a packet that matches the filter settings of this ACL entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.5 | ColumnaclNewCfgFilterActionSetPrio | read-write | current | The COS queue to be used when the action for this ACL entry is set to setprio. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.6 | ColumnaclNewCfgEthFmt | read-write | current | The packet ethernet format to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.7 | ColumnaclNewCfgTagFmt | read-write | current | The packet tagging format to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.8 | ColumnaclNewCfgIPFmt | read-write | current | The packet IP format to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.9 | ColumnaclNewCfgSrcMACAddress | read-write | current | The source MAC address to be filtered. Whenever this object is set to a nonzero value, the aclNewCfgSrcMACMask object, if not yet set, will be automatically se… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.10 | ColumnaclNewCfgSrcMACMask | read-write | current | The address mask to be applied to aclNewCfgSrcMACAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.11 | ColumnaclNewCfgDstMACAddress | read-write | current | The destination MAC address to be filtered. Whenever this object is set to a nonzero value, the aclNewCfgDstMACMask object, if not yet set, will be automatical… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.12 | ColumnaclNewCfgDstMACMask | read-write | current | The address mask to be applied to aclNewCfgDstMACAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.13 | ColumnaclNewCfgEthernetTypeName | read-write | current | The Ethernet type to be filtered. If the value of this object is other(7), the value of aclNewCfgEthernetTypeValue indicates the ethernet type that will be fil… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.14 | ColumnaclNewCfgEthernetTypeValue | read-write | current | The Ethernet type value to be filtered. The value of this object is equivalent to the value of aclNewCfgEthernetTypeName except when the value of aclNewCfgEthe… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.15 | ColumnaclNewCfgVLanId | read-write | current | The virtual LAN identifier to be filtered. Whenever this object is set to a nonzero value, the aclNewCfgVLanMask object, if not yet set, will be automatically … |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.16 | ColumnaclNewCfgVLanMask | read-write | current | The mask to be applied to aclNewCfgVLanId for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.17 | ColumnaclNewCfg8021pPriority | read-write | current | The 802.1p priority to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.18 | ColumnaclNewCfgTypeOfService | read-write | current | The type of service to be filtered. 'none' for not initialised, within the range 0-255 |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.19 | ColumnaclNewCfgProtocol | read-write | current | The protocol to be filtered. 'none' for not initialised, within the range 0-255 |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.20 | ColumnaclNewCfgSrcIPAddress | read-write | current | The source IP address to be filtered. Whenever this object is set to a nonzero value, the aclNewCfgSrcIPMask object, if not yet set, will be automatically set … |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.21 | ColumnaclNewCfgSrcIPMask | read-write | current | The address mask to be applied to aclNewCfgSrcIPAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.22 | ColumnaclNewCfgDstIPAddress | read-write | current | The destination IP address to be filtered. Whenever this object is set to a nonzero value, the aclNewCfgDstIPMask object, if not yet set, will be automatically… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.23 | ColumnaclNewCfgDstIPMask | read-write | current | The address mask to be applied to aclNewCfgDstIPAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.24 | ColumnaclNewCfgSrcPort | read-write | current | The source TCP/UDP port number to be filtered. Whenever this object is set if the aclNewCfgSrcPortMask object is not set will be automatically set to 65535 (0x… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.25 | ColumnaclNewCfgSrcPortMask | read-write | current | The mask to be applied to aclNewCfgSrcPort for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.26 | ColumnaclNewCfgDstPort | read-write | current | The destination TCP/UDP port number to be filtered. Whenever this object is set the aclNewCfgSrcPortMask object, if not yet set, will be automatically set to 6… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.27 | ColumnaclNewCfgDstPortMask | read-write | current | The mask to be applied to aclNewCfgDstPort for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.28 | ColumnaclNewCfgTCPFlags | read-write | current | The TCP flags to be filtered. The TCP flags are presented in bitmap format, as follows: OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|__tcpSYN(6) |||| ||||… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.29 | ColumnaclNewCfgEgressPortIndexes | read-only | current | The port list in the ACL configured for egress filtering. The ports are presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... |… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.30 | ColumnaclNewCfgStatistics | read-write | current | Whether statistics collection for this ACL is enabled or not. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.31 | ColumnaclNewCfgAddEgressPortIndex | read-write | current | The port to be added to the specified ACL for egress filtering. A value of zero is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.32 | ColumnaclNewCfgRemoveEgressPortIndex | read-write | current | The port to be removed from the specified ACL. A value of zero is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.33 | ColumnaclNewCfgDelete | read-write | current | This is an action object to delete an ACL entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.39 | ColumnaclNewCfgTCPFlagsMask | read-write | current | The TCP flags mask. The TCP flags are presented in bitmap format, as follows: OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|__tcpSYN(6) |||| ||||_____tcpAC… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.41 | ColumnaclNewCfgMeterAction | read-write | current | Meter Action for this ACL. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.42 | ColumnaclNewCfgMeterEnable | read-write | current | Meter state for this ACL. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.43 | ColumnaclNewCfgKbitsSec | read-write | current | The commited rate of meter associated with this ACL entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.44 | ColumnaclNewCfgKbitsBurst | read-write | current | The maximum burst size of the meter associated with this ACL entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.45 | ColumnaclNewCfgUser | read-write | current | Set user defined priority for this ACL. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.46 | ColumnaclNewCfgInprofDscp | read-write | current | Set in profile pkts DSCP value. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.47 | ColumnaclNewCfgTos | read-write | current | To enable/disable setting pkts based on TOS bits. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.48 | ColumnaclNewCfgOutprofDscp | read-write | current | Set out profile pkts DSCP value. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.49 | ColumnaclNewCfgUserEnable | read-write | current | Set update method for this ACL. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.50 | ColumnaclNewCfgInprofDscpEnable | read-write | current | Whether in profile update DSCP for this ACL is enabled or not. Only the value disable(0) can be set, causing the in profile update DSCP to be disabled for this… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.51 | ColumnaclNewCfgOutprofDscpEnable | read-write | current | Whether out profile update DSCP for this ACL is enabled or not. Only the value disable(0) can be set, causing the out profile update DSCP to be disabled for th… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.52 | ColumnaclNewCfgReset | read-write | current | This is an action object to reset an ACL entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.53 | ColumnaclNewCfgEthernetReset | read-write | current | This is an action object to reset an ACL Ethernet entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.54 | ColumnaclNewCfgIpv4Reset | read-write | current | This is an action object to reset an ACL IPV4 entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.55 | ColumnaclNewCfgTcpudpReset | read-write | current | This is an action object to reset an ACL Tcpudp entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.56 | ColumnaclNewCfgMeterReset | read-write | current | This is an action object to reset an ACL Meter entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.57 | ColumnaclNewCfgRemarkReset | read-write | current | This is an action object to reset an ACL Remark entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.58 | ColumnaclNewCfgRemarkInprofReset | read-write | current | This is an action object to reset an ACL Remark Inprof entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.59 | ColumnaclNewCfgRemarkOutprofReset | read-write | current | This is an action object to reset an ACL Remark Outprof entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.60 | ColumnaclNewCfgPktfmtReset | read-write | current | This is an action object to reset an ACL Pktfmt entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.74 | ColumnaclNewCfgMirrorPortIndex | read-write | current | Set port in the ACL for mirroring. n > 0 - the represented port is configured for mirroring. 0 - the represented port is not configured for mirroring. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.2.1.81 | ColumnaclNewCfgLog | read-write | current | Whether log for this ACL is enabled or not. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.1.5 | ScalaraclTableMaxSize | read-only | current | The maximum number of entries in the acl config tables. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.3 | NodeaclGroup | |||
| 1.3.6.1.4.1.26543.2.7.7.9.1.3.1 | TableaclGroupCurCfgTable | not-accessible | current | The table of current ACL Group configuration. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.3.1.1 | RowaclGroupCurCfgEntry | not-accessible | current | Information about a particular ACL configuration. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.3.1.1.1 | ColumnaclGroupCurCfgIndex | read-only | current | The index associated with this ACL Group entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.3.1.1.2 | ColumnaclGroupCurCfgMemberAcls | read-only | current | The ACL members of this ACL group, presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || | || || |_ ACL 9 || || || ||___ … |
| 1.3.6.1.4.1.26543.2.7.7.9.1.3.1.1.9 | ColumnaclGroupCurCfgMemberAcl6s | read-only | current | The ACL6 members of this ACL group, presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || | || || |_ ACL6 9 || || || ||__… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.3.2 | TableaclGroupNewCfgTable | not-accessible | current | The table of new ACL Group configuration. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.3.2.1 | RowaclGroupNewCfgEntry | not-accessible | current | New information about a particular ACL configuration. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.3.2.1.1 | ColumnaclGroupNewCfgIndex | read-only | current | The index associated with this ACL Group entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.3.2.1.2 | ColumnaclGroupNewCfgMemberAcls | read-only | current | The ACL members of this ACL group, presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || | || || |_ ACL 9 || || || ||___ … |
| 1.3.6.1.4.1.26543.2.7.7.9.1.3.2.1.4 | ColumnaclGroupNewCfgAddAcl | read-write | current | The index of the ACL entry to be added into this ACL group. A successful set operation on this object will also set the bit corresponding to the ACL entry in t… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.3.2.1.5 | ColumnaclGroupNewCfgRemoveAcl | read-write | current | The index of the ACL entry to be removed from this ACL group. A successful set operation on this object will unset the bit corresponding to the ACL entry in th… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.3.2.1.8 | ColumnaclGroupNewCfgDelete | read-write | current | This is an action object to delete an ACL group. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.3.2.1.9 | ColumnaclGroupNewCfgMemberAcl6s | read-only | current | The ACL6 members of this ACL group, presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || | || || |_ ACL6 9 || || || ||__… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.3.2.1.10 | ColumnaclGroupNewCfgAddAcl6 | read-write | current | The index of the ACL6 entry to be added into this ACL group. A successful set operation on this object will also set the bit corresponding to the ACL6 entry in… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.3.2.1.11 | ColumnaclGroupNewCfgRemoveAcl6 | read-write | current | The index of the ACL entry to be removed from this ACL group. A successful set operation on this object will unset the bit corresponding to the ACL entry in th… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.4 | NodeaclCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.9.1.4.1 | TableaclCurCfgPortTable | not-accessible | current | The table of port acl groups configuration. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.4.1.1 | RowaclCurCfgPortTableEntry | not-accessible | current | Information about a particular port acl configuration. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.4.1.1.1 | ColumnaclCurCfgPortIndex | read-only | current | The identifier of a particular port. This is also index to the entLogicalTable of Entity MIB. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.4.1.1.2 | ColumnaclCurCfgPortAclBmap | read-only | current | The acls applied to the port. The acls are presented in bitmap format. This string displays acl number from 1 to 896. in receiving order: OCTET 1 OCTET 2 .....… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.4.1.1.4 | ColumnaclCurCfgPortAclGrpBmap | read-only | current | The acl groups applied to the port. The acls are presented in bitmap format. This string displays acl number from 1 to 896. in receiving order: OCTET 1 OCTET 2… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.4.1.1.13 | ColumnaclCurCfgPortAcl6Bmap | read-only | current | The acls applied to the port. The acls are presented in bitmap format. This string displays acl number from 1 to 128. in receiving order: OCTET 1 OCTET 2 .....… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.4.2 | TableaclNewCfgPortTable | not-accessible | current | The table of port acl configuration. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.4.2.1 | RowaclNewCfgPortTableEntry | not-accessible | current | Information about a particular port acl groups configuration. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.4.2.1.1 | ColumnaclNewCfgPortIndex | read-only | current | The identifier of a particular port. This is also index to the entLogicalTable of Entity MIB. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.4.2.1.2 | ColumnaclNewCfgPortAddAcl | read-write | current | The acl to be added to the specified port. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.4.2.1.4 | ColumnaclNewCfgPortAddAclGrp | read-write | current | The acl group to be added to the specified port. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.4.2.1.5 | ColumnaclNewCfgPortRemoveAcl | read-write | current | The acl to be removed from the specified port. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.4.2.1.7 | ColumnaclNewCfgPortRemoveAclGrp | read-write | current | The acl group to be removed from the specified port. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.4.2.1.8 | ColumnaclNewCfgPortAclBmap | read-only | current | The acls applied to the port. The acls are presented in bitmap format. This string displays acl number from 1 to 896. in receiving order: OCTET 1 OCTET 2 .....… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.4.2.1.10 | ColumnaclNewCfgPortAclGrpBmap | read-only | current | The acl groups applied to the port. The acl groups are presented in bitmap format. This string displays group number from 1 to 4096. in receiving order: OCTET … |
| 1.3.6.1.4.1.26543.2.7.7.9.1.4.2.1.11 | ColumnaclNewCfgPortAddAcl6 | read-write | current | The acl6 to be added to the specified port. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.4.2.1.12 | ColumnaclNewCfgPortRemoveAcl6 | read-write | current | The acl6 to be removed from the specified port. A '0' value is returned when read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.4.2.1.13 | ColumnaclNewCfgPortAcl6Bmap | read-only | current | The acl6s applied to the port. The acl6s are presented in bitmap format. This string displays acl number from 1 to 128. in receiving order: OCTET 1 OCTET 2 ...… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5 | Nodeacl6List | |||
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1 | Tableacl6CurCfgTable | not-accessible | current | The table of current ACL6 configuration. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1 | Rowacl6CurCfgEntry | not-accessible | current | Current information about a particular ACL6 configuration entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.1 | Columnacl6CurCfgIndex | read-only | current | The index associated with this ACL6 entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.2 | Columnacl6CurCfgGroup | read-only | current | The index of the ACL group to which this ACL6 entry is a member of. A value of zero means the ACL6 is not a member of any group. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.3 | Columnacl6CurCfgFilterAction | read-only | current | The action to be performed on a packet that matches the filter settings of this ACL6 entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.4 | Columnacl6CurCfgFilterActionSetPrio | read-only | current | The value to be used when the action to be performed is setprio for this ACL6 entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.5 | Columnacl6CurCfgSrcIPv6Address | read-only | current | The source IPv6 address to be filtered. Address should be 4-byte hexadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xx… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.6 | Columnacl6CurCfgSrcIPv6PrefixLen | read-only | current | The IPv6 prefix applied to acl6CurCfgSrcIPv6PrefixLen for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.7 | Columnacl6CurCfgDstIPv6Address | read-only | current | The destination IPv6 address to be filtered. Address should be 4-byte hexadecimal colon notation. Valid IPv6 address should be in any of the following forms xx… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.8 | Columnacl6CurCfgDstIPv6PrefixLen | read-only | current | The IPv6 prefix applied to acl6CurCfgDstIPv6PrefixLen for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.9 | Columnacl6CurCfgIPv6FlowLabel | read-only | current | The IPv6 FlowLabel to be filtered. 'none' for not initialised, within the range 0-1048575 |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.10 | Columnacl6CurCfgIPv6TrafficClass | read-only | current | The IPv6 Traffic Class to be filtered. 'none' for not initialised, within the range 0-255 |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.11 | Columnacl6CurCfgIPv6NextHeader | read-only | current | The IPv6 next header to be filtered. 'none' for not initialised, within the range 0-255 |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.12 | Columnacl6CurCfgSrcPort | read-only | current | The source TCP/UDP port number to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.13 | Columnacl6CurCfgSrcPortMask | read-only | current | The mask applied to acl6CurCfgSrcPort for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.14 | Columnacl6CurCfgDstPort | read-only | current | The destination TCP/UDP port number to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.15 | Columnacl6CurCfgDstPortMask | read-only | current | The mask applied to acl6CurCfgDstPort for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.16 | Columnacl6CurCfgTCPFlags | read-only | current | The TCP flags to be filtered. OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|__tcpSYN(6) |||| ||||_____tcpACK(3) |||______tcpURG(2) ||_______reserved2(1) |_… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.17 | Columnacl6CurCfgTCPFlagsMask | read-only | current | The TCP flags mask. OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|__tcpSYN(6) |||| ||||_____tcpACK(3) |||______tcpURG(2) ||_______reserved2(1) |________res… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.18 | Columnacl6CurCfgEgressPortIndexes | read-only | current | The port list in the ACL6 configured for egress filtering. The ports are presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... … |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.19 | Columnacl6CurCfgStatistics | read-only | current | Whether statistics collection for this ACL6 is enabled or not. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.20 | Columnacl6CurCfgUser | read-only | current | Set user defined priority for this ACL6. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.21 | Columnacl6CurCfgInprofDscp | read-only | current | Set in profile pkts DSCP value. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.22 | Columnacl6CurCfgTos | read-only | current | To enable/disable setting pkts based on TOS bits. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.24 | Columnacl6CurCfgUserEnable | read-only | current | Set update method for this ACL6. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.25 | Columnacl6CurCfgInprofDscpEnable | read-only | current | Whether in profile update DSCP for this ACL6 is enabled or not. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.26 | Columnacl6CurCfgLog | read-only | current | Whether log for this ACL is enabled or not. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.28 | Columnacl6CurCfgMeterAction | read-only | current | Meter Action for this ACL. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.29 | Columnacl6CurCfgMeterEnable | read-only | current | Meter state for this ACL. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.30 | Columnacl6CurCfgKbitsSec | read-only | current | The commited rate of meter associated with this ACL entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.31 | Columnacl6CurCfgKbitsBurst | read-only | current | The maxmium burst sizeof meter associated with this ACL entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.32 | Columnacl6CurCfgOutprofDscp | read-only | current | Set out profile pkts DSCP value. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.1.1.33 | Columnacl6CurCfgOutprofDscpEnable | read-only | current | Whether out profile update DSCP for this ACL is enabled or not. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2 | Tableacl6NewCfgTable | not-accessible | current | The table of new ACL6 configuration. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1 | Rowacl6NewCfgEntry | not-accessible | current | New information about a particular ACL6 configuration. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.1 | Columnacl6NewCfgIndex | read-only | current | The index associated with this ACL6 entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.2 | Columnacl6NewCfgGroup | read-only | current | The index of the ACL group to which this ACL6 entry is a member of. A value of zero means the ACL6 is not a member of any group. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.3 | Columnacl6NewCfgFilterAction | read-write | current | The action to be performed on a packet that matches the filter settings of this ACL6 entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.4 | Columnacl6NewCfgFilterActionSetPrio | read-write | current | The COS queue to be used when the action for this ACL6 entry is set to setprio. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.5 | Columnacl6NewCfgSrcIPv6Address | read-write | current | The source IPv6 address to be filtered. Address should be 4-byte hexadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xx… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.6 | Columnacl6NewCfgSrcIPv6PrefixLen | read-write | current | The IPv6 prefix applied to acl6CurCfgSrcIPv6PrefixLen for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.7 | Columnacl6NewCfgDstIPv6Address | read-write | current | The destination IPv6 address to be filtered. Address should be 4-byte hexadecimal colon notation. Valid IPv6 address should be in any of the following forms xx… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.8 | Columnacl6NewCfgDstIPv6PrefixLen | read-write | current | The IPv6 prefix applied to acl6CurCfgDstIPv6PrefixLen for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.9 | Columnacl6NewCfgIPv6FlowLabel | read-write | current | The IPv6 flow label to be filtered. 'none' for not initialised, within the range 0-1048575 |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.10 | Columnacl6NewCfgIPv6TrafficClass | read-write | current | The IPv6 traffic class to be filtered. 'none' for not initialised, within the range 0-255 |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.11 | Columnacl6NewCfgIPv6NextHeader | read-write | current | The IPv6 next header to be filtered. 'none' for not initialised, within the range 0-255 |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.12 | Columnacl6NewCfgSrcPort | read-write | current | The source TCP/UDP port number to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.13 | Columnacl6NewCfgSrcPortMask | read-write | current | The mask applied to acl6CurCfgSrcPort for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.14 | Columnacl6NewCfgDstPort | read-write | current | The destination TCP/UDP port number to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.15 | Columnacl6NewCfgDstPortMask | read-write | current | The mask applied to acl6CurCfgDstPort for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.16 | Columnacl6NewCfgTCPFlags | read-write | current | The TCP flags to be filtered. OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|__tcpSYN(6) |||| ||||_____tcpACK(3) |||______tcpURG(2) ||_______reserved2(1) |_… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.17 | Columnacl6NewCfgTCPFlagsMask | read-write | current | The TCP flags mask. OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|__tcpSYN(6) |||| ||||_____tcpACK(3) |||______tcpURG(2) ||_______reserved2(1) |________res… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.18 | Columnacl6NewCfgEgressPortIndexes | read-only | current | The port list in the ACL6 configured for egress filtering. The ports are presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... … |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.19 | Columnacl6NewCfgStatistics | read-write | current | Whether statistics collection for this ACL6 is enabled or not. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.20 | Columnacl6NewCfgAddEgressPortIndex | read-write | current | The port to be added to the specified ACL6 for egress filtering. A value of zero is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.21 | Columnacl6NewCfgRemoveEgressPortIndex | read-write | current | The port to be removed from the specified ACL6. A value of zero is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.22 | Columnacl6NewCfgDelete | read-write | current | This is an action object to delete an ACL6 entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.23 | Columnacl6NewCfgUser | read-write | current | Set user defined priority for this ACL6. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.24 | Columnacl6NewCfgInprofDscp | read-write | current | Set in profile pkts DSCP value. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.25 | Columnacl6NewCfgTos | read-write | current | To enable/disable setting pkts based on TOS bits. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.27 | Columnacl6NewCfgUserEnable | read-write | current | Set update method for this ACL6. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.28 | Columnacl6NewCfgInprofDscpEnable | read-write | current | Whether in profile update DSCP for this ACL6 is enabled or not. Only the value disable(0) can be set, causing the in profile update DSCP to be disabled for thi… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.30 | Columnacl6NewCfgIPv6Reset | read-write | current | This is an action object to reset an ACL IPV6 entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.31 | Columnacl6NewCfgTcpudpReset | read-write | current | This is an action object to reset an ACL6 Tcpudp entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.32 | Columnacl6NewCfgRemarkInprofReset | read-write | current | This is an action object to reset an ACL Remark Inprof entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.33 | Columnacl6NewCfgLog | read-write | current | Whether log for this ACL is enabled or not. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.35 | Columnacl6NewCfgMeterAction | read-write | current | Meter Action for this ACL. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.36 | Columnacl6NewCfgMeterEnable | read-write | current | Meter state for this ACL. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.37 | Columnacl6NewCfgKbitsSec | read-write | current | The commited rate of meter associated with this ACL entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.38 | Columnacl6NewCfgKbitsBurst | read-write | current | The maximum burst size of the meter associated with this ACL entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.39 | Columnacl6NewCfgMeterReset | read-write | current | This is an action object to reset an ACL6 Meter entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.40 | Columnacl6NewCfgOutprofDscp | read-write | current | Set out profile pkts DSCP value. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.41 | Columnacl6NewCfgOutprofDscpEnable | read-write | current | Whether out profile update DSCP for this ACL is enabled or not. Only the value disable(0) can be set, causing the out profile update DSCP to be disabled for th… |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.2.1.42 | Columnacl6NewCfgRemarkOutprofReset | read-write | current | This is an action object to reset an ACL Remark Outprof entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.5.3 | Scalaracl6TableMaxSize | read-only | current | The maximum number of entries in the acl6 config tables. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.6 | NodeaclLog | |||
| 1.3.6.1.4.1.26543.2.7.7.9.1.6.1 | ScalaraclLogCurInterval | read-only | current | The interval secends of displaying Logs. Default is 300s. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.6.2 | ScalaraclLogNewInterval | read-write | current | The interval secends of displaying Logs. Default is 300s. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.6.3 | ScalaraclLogCurRateLimit | read-only | current | The rate limit of ACL Log queue. Default is 10pps. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.6.4 | ScalaraclLogNewRateLimit | read-write | current | The rate limit of ACL Log queue. Default is 10pps. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7 | NodemAcl | |||
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.1 | TablemAclCurCfgTable | not-accessible | current | The table of current Management ACL configuration. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.1.1 | RowmAclCurCfgEntry | not-accessible | current | Current information about a particular Management ACL configuration entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.1.1.1 | ColumnmAclCurCfgIndex | read-only | current | The index associated with this Management ACL entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.1.1.2 | ColumnmAclCurCfgUserEnable | read-only | current | Set update method for this mACL. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.1.1.3 | ColumnmAclCurCfgFilterAction | read-only | current | The action to be performed on a packet that matches the filter settings of this mACL entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.1.1.4 | ColumnmAclCurCfgProtocol | read-only | current | The protocol to be filtered. 'none' for not initialised, within the range 0-255 |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.1.1.5 | ColumnmAclCurCfgSrcIPAddress | read-only | current | The source IP address to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.1.1.6 | ColumnmAclCurCfgSrcIPMask | read-only | current | The address mask applied to mAclCurCfgSrcIPAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.1.1.7 | ColumnmAclCurCfgDstIPAddress | read-only | current | The destination IP address to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.1.1.8 | ColumnmAclCurCfgDstIPMask | read-only | current | The address mask applied to mAclCurCfgDstIPAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.1.1.9 | ColumnmAclCurCfgSrcPort | read-only | current | The source TCP/UDP port number to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.1.1.10 | ColumnmAclCurCfgSrcPortMask | read-only | current | The mask applied to mAclCurCfgSrcPort for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.1.1.11 | ColumnmAclCurCfgDstPort | read-only | current | The destination TCP/UDP port number to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.1.1.12 | ColumnmAclCurCfgDstPortMask | read-only | current | The mask applied to mAclCurCfgDstPort for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.1.1.13 | ColumnmAclCurCfgStatistics | read-only | current | Whether statistics collection for this mACL is enabled or not. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.2 | TablemAclNewCfgTable | not-accessible | current | The table of new Management ACL configuration. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.2.1 | RowmAclNewCfgEntry | not-accessible | current | New information about a particular Management ACL configuration entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.2.1.1 | ColumnmAclNewCfgIndex | read-only | current | The index associated with this Management ACL entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.2.1.2 | ColumnmAclNewCfgUserEnable | read-write | current | Set update method for this mACL. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.2.1.3 | ColumnmAclNewCfgFilterAction | read-write | current | The action to be performed on a packet that matches the filter settings of this mACL entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.2.1.4 | ColumnmAclNewCfgProtocol | read-write | current | The protocol to be filtered. 'none' for not initialised, within the range 0-255 |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.2.1.5 | ColumnmAclNewCfgSrcIPAddress | read-write | current | The source IP address to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.2.1.6 | ColumnmAclNewCfgSrcIPMask | read-write | current | The address mask applied to mAclNewCfgSrcIPAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.2.1.7 | ColumnmAclNewCfgDstIPAddress | read-write | current | The destination IP address to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.2.1.8 | ColumnmAclNewCfgDstIPMask | read-write | current | The address mask applied to mAclNewCfgDstIPAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.2.1.9 | ColumnmAclNewCfgSrcPort | read-write | current | The source TCP/UDP port number to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.2.1.10 | ColumnmAclNewCfgSrcPortMask | read-write | current | The mask applied to mAclNewCfgSrcPort for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.2.1.11 | ColumnmAclNewCfgDstPort | read-write | current | The destination TCP/UDP port number to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.2.1.12 | ColumnmAclNewCfgDstPortMask | read-write | current | The mask applied to mAclNewCfgDstPort for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.2.1.13 | ColumnmAclNewCfgStatistics | read-write | current | Whether statistics collection for this mACL is enabled or not. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.2.1.14 | ColumnmAclNewCfgDelete | read-write | current | This is an action object to delete an MACL entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.2.1.15 | ColumnmAclNewCfgReset | read-write | current | This is an action object to reset an MACL entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.2.1.16 | ColumnmAclNewCfgIpv4Reset | read-write | current | This is an action object to reset an ACL IPV4 entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.1.7.2.1.17 | ColumnmAclNewCfgTcpudpReset | read-write | current | This is an action object to reset an MACL Tcpudp entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.3 | NodevmapConfig | |||
| 1.3.6.1.4.1.26543.2.7.7.9.3.1 | NodevmapList | |||
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1 | TablevmapCurCfgTable | not-accessible | current | The table of current VMAP configuration. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1 | RowvmapCurCfgEntry | not-accessible | current | Current information about a particular VMAP configuration entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.1 | ColumnvmapCurCfgIndex | read-only | current | The index associated with this VMAP entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.2 | ColumnvmapCurCfgFilterAction | read-only | current | The action to be performed on a packet that matches the filter settings of this VMAP entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.3 | ColumnvmapCurCfgFilterActionSetPrio | read-only | current | The value to be used when the action to be performed is setprio for this VMAP entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.4 | ColumnvmapCurCfgEthFmt | read-only | current | The packet ethernet format to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.5 | ColumnvmapCurCfgTagFmt | read-only | current | The packet tag format to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.6 | ColumnvmapCurCfgIPFmt | read-only | current | The packet IP format to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.7 | ColumnvmapCurCfgSrcMACAddress | read-only | current | The source MAC address to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.8 | ColumnvmapCurCfgSrcMACMask | read-only | current | The address mask applied to aclCurCfgSrcMACAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.9 | ColumnvmapCurCfgDstMACAddress | read-only | current | The destination MAC address to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.10 | ColumnvmapCurCfgDstMACMask | read-only | current | The address mask applied to aclCurCfgDstMACAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.11 | ColumnvmapCurCfgEthernetTypeName | read-only | current | The Ethernet type to be filtered. If the value of this object is other(7), the value of aclNewCfgEthernetTypeValue indicates the ethernet type that will be fil… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.12 | ColumnvmapCurCfgEthernetTypeValue | read-only | current | The Ethernet type value to be filtered. The value of this object is equivalent to the value of aclNewCfgEthernetTypeName except when the value of aclNewCfgEthe… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.13 | ColumnvmapCurCfg8021pPriority | read-only | current | The 802.1p priority to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.14 | ColumnvmapCurCfgTypeOfService | read-only | current | The type of service to be filtered. 'none' for not initialised, within the range 0-255 |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.15 | ColumnvmapCurCfgProtocol | read-only | current | The protocol to be filtered. 'none' for not initialised, within the range 0-255 |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.16 | ColumnvmapCurCfgSrcIPAddress | read-only | current | The source IP address to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.17 | ColumnvmapCurCfgSrcIPMask | read-only | current | The address mask applied to aclCurCfgSrcIPAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.18 | ColumnvmapCurCfgDstIPAddress | read-only | current | The destination IP address to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.19 | ColumnvmapCurCfgDstIPMask | read-only | current | The address mask applied to aclCurCfgDstIPAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.20 | ColumnvmapCurCfgSrcPort | read-only | current | The source TCP/UDP port number to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.21 | ColumnvmapCurCfgSrcPortMask | read-only | current | The mask applied to aclCurCfgSrcPort for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.22 | ColumnvmapCurCfgDstPort | read-only | current | The destination TCP/UDP port number to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.23 | ColumnvmapCurCfgDstPortMask | read-only | current | The mask applied to aclCurCfgDstPort for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.24 | ColumnvmapCurCfgTCPFlags | read-only | current | The TCP flags to be filtered. OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|__tcpSYN(6) |||| ||||_____tcpACK(3) |||______tcpURG(2) ||_______reserved2(1) |_… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.25 | ColumnvmapCurCfgTCPFlagsMask | read-only | current | The TCP flags mask. OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|__tcpSYN(6) |||| ||||_____tcpACK(3) |||______tcpURG(2) ||_______reserved2(1) |________res… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.26 | ColumnvmapCurCfgEgressPorts | read-only | current | The port list in the VMAP configured for egress filtering. The ports are presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... … |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.27 | ColumnvmapCurCfgStatistics | read-only | current | Whether statistics collection for this VMAP is enabled or not. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.31 | ColumnvmapCurCfgMeterAction | read-only | current | Meter Action for this VMAP. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.32 | ColumnvmapCurCfgMeterEnable | read-only | current | Meter state for this VMAP. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.33 | ColumnvmapCurCfgKbitsSec | read-only | current | The commited rate of meter associated with this VMAP entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.34 | ColumnvmapCurCfgKbitsBurst | read-only | current | The maxmium burst sizeof meter associated with this VMAP entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.35 | ColumnvmapCurCfgUser | read-only | current | Set user defined priority for this VMAP. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.36 | ColumnvmapCurCfgInprofDscp | read-only | current | Set in profile pkts DSCP value. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.37 | ColumnvmapCurCfgTos | read-only | current | To enable/disable setting pkts based on TOS bits. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.38 | ColumnvmapCurCfgOutprofDscp | read-only | current | Set out profile pkts DSCP value. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.39 | ColumnvmapCurCfgUserEnable | read-only | current | Set update method for this VMAP. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.40 | ColumnvmapCurCfgInprofDscpEnable | read-only | current | Whether in profile update DSCP for this VMAP is enabled or not. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.41 | ColumnvmapCurCfgOutprofDscpEnable | read-only | current | Whether out profile update DSCP for this VMAP is enabled or not. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.1.1.51 | ColumnvmapCurCfgMirrorPort | read-only | current | Set port in the VMAP for mirroring. n > 0 - the represented port is configured for mirroring. 0 - the represented port is not configured for mirroring. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2 | TablevmapNewCfgTable | not-accessible | current | The table of new VMAP configuration. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1 | RowvmapNewCfgEntry | not-accessible | current | New information about a particular VMAP configuration. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.1 | ColumnvmapNewCfgIndex | read-only | current | The index associated with this VMAP entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.2 | ColumnvmapNewCfgFilterAction | read-write | current | The action to be performed on a packet that matches the filter settings of this VMAP entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.3 | ColumnvmapNewCfgFilterActionSetPrio | read-write | current | The COS queue to be used when the action for this VMAP entry is set to setprio. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.4 | ColumnvmapNewCfgEthFmt | read-write | current | The packet ethernet format to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.5 | ColumnvmapNewCfgTagFmt | read-write | current | The packet tagging format to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.6 | ColumnvmapNewCfgIPFmt | read-write | current | The packet IP format to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.7 | ColumnvmapNewCfgSrcMACAddress | read-write | current | The source MAC address to be filtered. Whenever this object is set to a nonzero value, the aclNewCfgSrcMACMask object, if not yet set, will be automatically se… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.8 | ColumnvmapNewCfgSrcMACMask | read-write | current | The address mask to be applied to aclNewCfgSrcMACAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.9 | ColumnvmapNewCfgDstMACAddress | read-write | current | The destination MAC address to be filtered. Whenever this object is set to a nonzero value, the aclNewCfgDstMACMask object, if not yet set, will be automatical… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.10 | ColumnvmapNewCfgDstMACMask | read-write | current | The address mask to be applied to aclNewCfgDstMACAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.11 | ColumnvmapNewCfgEthernetTypeName | read-write | current | The Ethernet type to be filtered. If the value of this object is other(7), the value of aclNewCfgEthernetTypeValue indicates the ethernet type that will be fil… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.12 | ColumnvmapNewCfgEthernetTypeValue | read-write | current | The Ethernet type value to be filtered. The value of this object is equivalent to the value of aclNewCfgEthernetTypeName except when the value of aclNewCfgEthe… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.13 | ColumnvmapNewCfg8021pPriority | read-write | current | The 802.1p priority to be filtered. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.14 | ColumnvmapNewCfgTypeOfService | read-write | current | The type of service to be filtered. 'none' for not initialised, within the range 0-255 |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.15 | ColumnvmapNewCfgProtocol | read-write | current | The protocol to be filtered. 'none' for not initialised, within the range 0-255 |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.16 | ColumnvmapNewCfgSrcIPAddress | read-write | current | The source IP address to be filtered. Whenever this object is set to a nonzero value, the aclNewCfgSrcIPMask object, if not yet set, will be automatically set … |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.17 | ColumnvmapNewCfgSrcIPMask | read-write | current | The address mask to be applied to aclNewCfgSrcIPAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.18 | ColumnvmapNewCfgDstIPAddress | read-write | current | The destination IP address to be filtered. Whenever this object is set to a nonzero value, the aclNewCfgDstIPMask object, if not yet set, will be automatically… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.19 | ColumnvmapNewCfgDstIPMask | read-write | current | The address mask to be applied to aclNewCfgDstIPAddress for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.20 | ColumnvmapNewCfgSrcPort | read-write | current | The source TCP/UDP port number to be filtered. Whenever this object is set if the aclNewCfgSrcPortMask object is not set will be automatically set to 65535 (0x… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.21 | ColumnvmapNewCfgSrcPortMask | read-write | current | The mask to be applied to aclNewCfgSrcPort for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.22 | ColumnvmapNewCfgDstPort | read-write | current | The destination TCP/UDP port number to be filtered. Whenever this object is set the aclNewCfgSrcPortMask object, if not yet set, will be automatically set to 6… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.23 | ColumnvmapNewCfgDstPortMask | read-write | current | The mask to be applied to aclNewCfgDstPort for filtering. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.24 | ColumnvmapNewCfgTCPFlags | read-write | current | The TCP flags to be filtered. The TCP flags are presented in bitmap format, as follows: OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|__tcpSYN(6) |||| ||||… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.25 | ColumnvmapNewCfgTCPFlagsMask | read-write | current | The TCP flags mask. The TCP flags are presented in bitmap format, as follows: OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|__tcpSYN(6) |||| ||||_____tcpAC… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.26 | ColumnvmapNewCfgEgressPorts | read-only | current | The port list in the VMAP configured for egress filtering. The ports are presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... … |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.27 | ColumnvmapNewCfgStatistics | read-write | current | Whether statistics collection for this VMAP is enabled or not. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.28 | ColumnvmapNewCfgAddEgressPort | read-write | current | The port to be added to the specified VMAP for egress filtering. A value of zero is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.29 | ColumnvmapNewCfgRemoveEgressPort | read-write | current | The port to be removed from the specified VMAP. A value of zero is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.30 | ColumnvmapNewCfgDelete | read-write | current | This is an action object to delete an VMAP entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.31 | ColumnvmapNewCfgMeterAction | read-write | current | Meter Action for this VMAP. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.32 | ColumnvmapNewCfgMeterEnable | read-write | current | Meter state for this VMAP. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.33 | ColumnvmapNewCfgKbitsSec | read-write | current | The commited rate of meter associated with this VMAP entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.34 | ColumnvmapNewCfgKbitsBurst | read-write | current | The maximum burst size of the meter associated with this VMAP entry. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.35 | ColumnvmapNewCfgUser | read-write | current | Set user defined priority for this VMAP. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.36 | ColumnvmapNewCfgInprofDscp | read-write | current | Set in profile pkts DSCP value. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.37 | ColumnvmapNewCfgTos | read-write | current | To enable/disable setting pkts based on TOS bits. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.38 | ColumnvmapNewCfgOutprofDscp | read-write | current | Set out profile pkts DSCP value. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.39 | ColumnvmapNewCfgUserEnable | read-write | current | Set update method for this VMAP. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.40 | ColumnvmapNewCfgInprofDscpEnable | read-write | current | Whether in profile update DSCP for this VMAP is enabled or not. Only the value disable(0) can be set, causing the in profile update DSCP to be disabled for thi… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.41 | ColumnvmapNewCfgOutprofDscpEnable | read-write | current | Whether out profile update DSCP for this VMAP is enabled or not. Only the value disable(0) can be set, causing the out profile update DSCP to be disabled for t… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.42 | ColumnvmapNewCfgReset | read-write | current | This is an action object to reset an VMAP entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.43 | ColumnvmapNewCfgEthernetReset | read-write | current | This is an action object to reset an VMAP Ethernet entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.44 | ColumnvmapNewCfgIpv4Reset | read-write | current | This is an action object to reset an VMAP IPV4 entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.45 | ColumnvmapNewCfgTcpudpReset | read-write | current | This is an action object to reset an VMAP Tcpudp entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.46 | ColumnvmapNewCfgMeterReset | read-write | current | This is an action object to reset an VMAP Meter entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.47 | ColumnvmapNewCfgRemarkReset | read-write | current | This is an action object to reset an VMAP Remark entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.48 | ColumnvmapNewCfgRemarkInprofReset | read-write | current | This is an action object to reset an VMAP Remark Inprof entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.49 | ColumnvmapNewCfgRemarkOutprofReset | read-write | current | This is an action object to reset an VMAP Remark Outprof entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.50 | ColumnvmapNewCfgPktfmtReset | read-write | current | This is an action object to reset an VMAP Pktfmt entry. A value of other(1) is always returned when this object is read. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.1.2.1.51 | ColumnvmapNewCfgMirrorPort | read-write | current | Set port in the VMAP for mirroring. n > 0 - the represented port is configured for mirroring. 0 - the represented port is not configured for mirroring. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2 | NodevmapCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1 | NodevmapVlanCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.1 | NodevmapVlanCfgNonServerPorts | |||
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.1.1 | TablevmapVlanCurCfgNonServerPortsTable | not-accessible | current | The table of the current configuration of vmaps for the non-server ports of vlans. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.1.1.1 | RowvmapVlanCurCfgNonServerPortsTableEntry | not-accessible | current | A row in the table of current configuration of vmaps for the non-server ports of vlans. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.1.1.1.1 | ColumnvmapVlanCurCfgNonServerPortsVlanIdx | read-only | current | The vlan id in the table of configured vmaps for the non-server ports of vlan |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.1.1.1.2 | ColumnvmapVlanCurCfgNonServerPortsVmapBitmap | read-only | current | The bitmap of vmaps configured for the non-server ports of the vlan given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OC… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.1.2 | TablevmapVlanNewCfgNonServerPortsTable | not-accessible | current | The table of the new configuration of vmaps for non-server ports of vlans. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.1.2.1 | RowvmapVlanNewCfgNonServerPortsTableEntry | not-accessible | current | A row in the table of new configuration of vmaps for the non-server ports of vlans. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.1.2.1.1 | ColumnvmapVlanNewCfgNonServerPortsVlanIdx | read-only | current | The vlan id in the table of configured vmaps for the non-server ports of vlan |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.1.2.1.2 | ColumnvmapVlanNewCfgNonServerPortsVmapBitmap | read-only | current | The bitmap of vmaps configured for the non-server ports of the vlan given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OC… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.1.2.1.3 | ColumnvmapVlanNewCfgNonServerPortsAddVmap | read-write | current | Add a new vmap to the non-server ports of the vlan |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.1.2.1.4 | ColumnvmapVlanNewCfgNonServerPortsRemVmap | read-write | current | Remove a vmap from the non-server ports of the vlan |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.2 | NodevmapVlanCfgServerPorts | |||
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.2.1 | TablevmapVlanCurCfgServerPortsTable | not-accessible | current | The table of the current configuration of vmaps for server ports of vlans. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.2.1.1 | RowvmapVlanCurCfgServerPortsTableEntry | not-accessible | current | A row in the table of current configuration of vmaps for the server ports of vlans. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.2.1.1.1 | ColumnvmapVlanCurCfgServerPortsVlanIdx | read-only | current | The vlan id in the table of configured vmaps for the server ports of vlan |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.2.1.1.2 | ColumnvmapVlanCurCfgServerPortsVmapBitmap | read-only | current | The bitmap of vmaps configured for the server ports of the vlan given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OCTET … |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.2.2 | TablevmapVlanNewCfgServerPortsTable | not-accessible | current | The table of the new configuration of vmaps for server ports of vlans. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.2.2.1 | RowvmapVlanNewCfgServerPortsTableEntry | not-accessible | current | A row in the table of new configuration of vmaps for the server ports of vlans. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.2.2.1.1 | ColumnvmapVlanNewCfgServerPortsVlanIdx | read-only | current | The vlan id in the table of configured vmaps for the server ports of vlan |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.2.2.1.2 | ColumnvmapVlanNewCfgServerPortsVmapBitmap | read-only | current | The bitmap of vmaps configured for the server ports of the vlan given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OCTET … |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.2.2.1.3 | ColumnvmapVlanNewCfgServerPortsAddVmap | read-write | current | Add a new vmap to the server ports of the vlan |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.2.2.1.4 | ColumnvmapVlanNewCfgServerPortsRemVmap | read-write | current | Remove a vmap from the server ports of the vlan |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.3 | NodevmapVlanCfgAllPorts | |||
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.3.1 | TablevmapVlanCurCfgAllPortsTable | not-accessible | current | The table of the current configuration of vmaps for all ports of vlans. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.3.1.1 | RowvmapVlanCurCfgAllPortsTableEntry | not-accessible | current | A row in the table of current configuration of vmaps for all ports of vlans. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.3.1.1.1 | ColumnvmapVlanCurCfgAllPortsVlanIdx | read-only | current | The vlan id in the table of configured vmaps for all ports of vlan |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.3.1.1.2 | ColumnvmapVlanCurCfgAllPortsVmapBitmap | read-only | current | The bitmap of vmaps configured for the internal ports of the vlan given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OCTE… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.3.2 | TablevmapVlanNewCfgAllPortsTable | not-accessible | current | The table of the new configuration of vmaps for all ports of vlans. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.3.2.1 | RowvmapVlanNewCfgAllPortsTableEntry | not-accessible | current | A row in the table of new configuration of vmaps for all ports of vlans. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.3.2.1.1 | ColumnvmapVlanNewCfgAllPortsVlanIdx | read-only | current | The vlan id in the table of configured vmaps for all ports of vlan |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.3.2.1.2 | ColumnvmapVlanNewCfgAllPortsVmapBitmap | read-only | current | The bitmap of vmaps configured for the internal ports of the vlan given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OCTE… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.3.2.1.3 | ColumnvmapVlanNewCfgAllPortsAddVmap | read-write | current | Add a new vmap to all ports of the vlan |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.1.3.2.1.4 | ColumnvmapVlanNewCfgAllPortsRemVmap | read-write | current | Remove a vmap from all vlan ports |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2 | NodevmapGroupCfg | |||
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.1 | NodevmapGroupCfgNonServerPorts | |||
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.1.1 | TablevmapGroupCurCfgNonServerPortsTable | not-accessible | current | The table of the current configuration of vmaps for non-server ports of vm groups. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.1.1.1 | RowvmapGroupCurCfgNonServerPortsTableEntry | not-accessible | current | A row in the table of current configuration of vmaps for the non-server ports of vm groups. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.1.1.1.1 | ColumnvmapGroupCurCfgNonServerPortsGroupIdx | read-only | current | The vm group id in the table of configured vmaps for the non-server ports of vm group |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.1.1.1.2 | ColumnvmapGroupCurCfgNonServerPortsVmapBitmap | read-only | current | The bitmap of vmaps configured for the non-server ports of the vm group given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET … |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.1.2 | TablevmapGroupNewCfgNonServerPortsTable | not-accessible | current | The table of the new configuration of vmaps for non-server ports of vm groups. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.1.2.1 | RowvmapGroupNewCfgNonServerPortsTableEntry | not-accessible | current | A row in the table of new configuration of vmaps for the non-server ports of vm groups. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.1.2.1.1 | ColumnvmapGroupNewCfgNonServerPortsGroupIdx | read-only | current | The vm group id in the table of configured vmaps for the non-server ports of vm group |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.1.2.1.2 | ColumnvmapGroupNewCfgNonServerPortsVmapBitmap | read-only | current | The bitmap of vmaps configured for the non-server ports of the vm group given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET … |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.1.2.1.3 | ColumnvmapGroupNewCfgNonServerPortsAddVmap | read-write | current | Add a new vmap to the non-server ports of the vm group |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.1.2.1.4 | ColumnvmapGroupNewCfgNonServerPortsRemVmap | read-write | current | Remove a vmap from the non-server ports of the vm group |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.2 | NodevmapGroupCfgServerPorts | |||
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.2.1 | TablevmapGroupCurCfgServerPortsTable | not-accessible | current | The table of the current configuration of vmaps for server ports of vm groups. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.2.1.1 | RowvmapGroupCurCfgServerPortsTableEntry | not-accessible | current | A row in the table of current configuration of vmaps for the server ports of vm groups. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.2.1.1.1 | ColumnvmapGroupCurCfgServerPortsGroupIdx | read-only | current | The vm group id in the table of configured vmaps for the server ports of vm group |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.2.1.1.2 | ColumnvmapGroupCurCfgServerPortsVmapBitmap | read-only | current | The bitmap of vmaps configured for the server ports of the vm group given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OC… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.2.2 | TablevmapGroupNewCfgServerPortsTable | not-accessible | current | The table of the new configuration of vmaps for server ports of vm groups. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.2.2.1 | RowvmapGroupNewCfgServerPortsTableEntry | not-accessible | current | A row in the table of new configuration of vmaps for the server ports of vm groups. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.2.2.1.1 | ColumnvmapGroupNewCfgServerPortsGroupIdx | read-only | current | The vm group id in the table of configured vmaps for the server ports of vm group |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.2.2.1.2 | ColumnvmapGroupNewCfgServerPortsVmapBitmap | read-only | current | The bitmap of vmaps configured for the server ports of the vm group given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OC… |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.2.2.1.3 | ColumnvmapGroupNewCfgServerPortsAddVmap | read-write | current | Add a new vmap to the server ports of the vm group |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.2.2.1.4 | ColumnvmapGroupNewCfgServerPortsRemVmap | read-write | current | Remove a vmap from the server ports of the vm group |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.3 | NodevmapGroupCfgAllPorts | |||
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.3.1 | TablevmapGroupCurCfgAllPortsTable | not-accessible | current | The table of the current configuration of vmaps for all ports of vm groups. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.3.1.1 | RowvmapGroupCurCfgAllPortsTableEntry | not-accessible | current | A row in the table of current configuration of vmaps for all ports of vm groups. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.3.1.1.1 | ColumnvmapGroupCurCfgAllPortsGroupIdx | read-only | current | The vm group id in the table of configured vmaps for all ports of vm group |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.3.1.1.2 | ColumnvmapGroupCurCfgAllPortsVmapBitmap | read-only | current | The bitmap of vmaps configured for the internal ports of the vm group given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 … |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.3.2 | TablevmapGroupNewCfgAllPortsTable | not-accessible | current | The table of the new configuration of vmaps for all ports of vm groups. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.3.2.1 | RowvmapGroupNewCfgAllPortsTableEntry | not-accessible | current | A row in the table of new configuration of vmaps for all ports of vm groups. |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.3.2.1.1 | ColumnvmapGroupNewCfgAllPortsGroupIdx | read-only | current | The vm group id in the table of configured vmaps for all ports of vm group |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.3.2.1.2 | ColumnvmapGroupNewCfgAllPortsVmapBitmap | read-only | current | The bitmap of vmaps configured for the internal ports of the vm group given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 … |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.3.2.1.3 | ColumnvmapGroupNewCfgAllPortsAddVmap | read-write | current | Add a new vmap to all ports of the vm group |
| 1.3.6.1.4.1.26543.2.7.7.9.3.2.2.3.2.1.4 | ColumnvmapGroupNewCfgAllPortsRemVmap | read-write | current | Remove a vmap from all vm group ports |
| 1.3.6.1.4.1.26543.2.7.7.15 | Nodevirt | |||
| 1.3.6.1.4.1.26543.2.7.7.15.1 | NodevirtGeneral | |||
| 1.3.6.1.4.1.26543.2.7.7.15.1.1 | ScalarvirtCurCfgState | read-only | current | VM groups global state. |
| 1.3.6.1.4.1.26543.2.7.7.15.1.2 | ScalarvirtNewCfgState | read-write | current | Enable/Disable Virtual Machine Groups |
| 1.3.6.1.4.1.26543.2.7.7.15.1.3 | ScalarvirtCurCfgHbPort | read-only | current | Current esx/esxi server to vcenter heartbeat UDP port |
| 1.3.6.1.4.1.26543.2.7.7.15.1.4 | ScalarvirtNewCfgHbPort | read-write | current | Set new esx/esxi server to vcenter heartbeat UDP port |
| 1.3.6.1.4.1.26543.2.7.7.15.1.5 | ScalarvirtCurCfgVirtCenterIp | read-only | current | The IP address of the Virtual Center. |
| 1.3.6.1.4.1.26543.2.7.7.15.1.6 | ScalarvirtNewCfgVirtCenterIp | read-write | current | The IP address of the Virtual Center. |
| 1.3.6.1.4.1.26543.2.7.7.15.1.7 | ScalarvirtCurCfgVirtCenterUser | read-only | current | Virtual Center username. |
| 1.3.6.1.4.1.26543.2.7.7.15.1.8 | ScalarvirtNewCfgVirtCenterUser | read-write | current | Virtual Center username. |
| 1.3.6.1.4.1.26543.2.7.7.15.1.9 | ScalarvirtCurCfgVirtCenterSSLAuth | read-only | current | Authenticate SSL Certificate. |
| 1.3.6.1.4.1.26543.2.7.7.15.1.10 | ScalarvirtNewCfgVirtCenterSSLAuth | read-write | current | Authenticate SSL Certificate. |
| 1.3.6.1.4.1.26543.2.7.7.15.1.11 | ScalarvirtNewCfgVirtCenterPasswd | read-write | current | Virtual Center password. |
| 1.3.6.1.4.1.26543.2.7.7.15.1.12 | ScalarvirtNewCfgVirtCenterDelete | read-write | current | Delete Virtual Center specifications |
| 1.3.6.1.4.1.26543.2.7.7.15.2 | NodevmGroups | |||
| 1.3.6.1.4.1.26543.2.7.7.15.2.1 | TablevmCurCfgGroupTable | not-accessible | current | The table of VM groups in the current config |
| 1.3.6.1.4.1.26543.2.7.7.15.2.1.1 | RowvmCurCfgGroupEntry | not-accessible | current | Information about VM on a group in current config. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.1.1.1 | ColumnvmCurCfgGroupIndex | read-only | current | The index of the vm group table. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.1.1.2 | ColumnvmCurCfgGroupVlan | read-only | current | Current Vlan used by the group. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.1.1.3 | ColumnvmCurCfgGroupPorts | read-only | current | The port list in the VM Group. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || |… |
| 1.3.6.1.4.1.26543.2.7.7.15.2.1.1.4 | ColumnvmCurCfgGroupTagState | read-only | current | Enable VLAN tagging on all VM group ports. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.1.1.5 | ColumnvmCurCfgGroupStg | read-only | current | Current stg of the group vlan. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.1.1.17 | ColumnvmCurCfgGroupProfileName | read-only | current | Current profile name used by the group. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.1.1.18 | ColumnvmCurCfgGroupValidateMode | read-only | current | Current validation mode used by the group. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2 | TablevmNewCfgGroupTable | not-accessible | current | The table of VM groups in the new config |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1 | RowvmNewCfgGroupEntry | not-accessible | current | Information about VM on a group in new config. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.1 | ColumnvmNewCfgGroupIndex | read-only | current | The index of the vm group table. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.2 | ColumnvmNewCfgGroupVlan | read-write | current | Set Vlan to be used by the group. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.3 | ColumnvmNewCfgGroupPorts | read-only | current | The port list in the VM Group. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || |… |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.4 | ColumnvmNewCfgGroupAddVm | read-write | current | Add a virtual machine to the group by UUID / Name / IP / MAC Address Note: MAC address format xx:xx:xx:xx:xx:xx |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.5 | ColumnvmNewCfgGroupRemVm | read-write | current | Remove a virtual machine from the group by UUID / Name / IP / MAC Address Note: MAC address format xx:xx:xx:xx:xx:xx |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.6 | ColumnvmNewCfgGroupAddVmIdx | read-write | current | Add virtual MAC address by index to the group. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.7 | ColumnvmNewCfgGroupRemVmIdx | read-write | current | Remove a virtual MAC address by index from the group. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.8 | ColumnvmNewCfgGroupAddPortIdx | read-write | current | Add a port to the group. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.9 | ColumnvmNewCfgGroupRemPortIdx | read-write | current | Remove a port from the group. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.10 | ColumnvmNewCfgGroupAddTrunk | read-write | current | Add trunk to the group. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.11 | ColumnvmNewCfgGroupRemTrunk | read-write | current | Remove trunk from the group. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.12 | ColumnvmNewCfgGroupTagState | read-write | current | Enable VLAN tagging on all VM group ports. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.13 | ColumnvmNewCfgGroupAddLacpKey | read-write | current | Add LACP trunk to the group. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.14 | ColumnvmNewCfgGroupRemLacpKey | read-write | current | Remove LACP trunk from the group. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.15 | ColumnvmNewCfgGroupAddProfile | read-write | current | Add VM Profile to the group. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.16 | ColumnvmNewCfgGroupRemProfile | read-write | current | Remove any VM profile associated with the group. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.17 | ColumnvmNewCfgGroupProfileName | read-only | current | New profile name to be used by the group. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.18 | ColumnvmNewCfgGroupDelete | read-write | current | Delete VM Group. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.19 | ColumnvmNewCfgGroupStg | read-write | current | Set group vlan spanning tree group. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.2.1.20 | ColumnvmNewCfgGroupValidateMode | read-write | current | Set group validation mode: noValidation : no validation will be performed. basicCheck: validate ESX port. advancedCheck: validate ESX port and VM UUID. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.3 | TablevmCurCfgGroupMacTable | not-accessible | current | Virtual machine group current configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.3.1 | RowvmCurCfgGroupMaclistEntry | not-accessible | current | Information about virtual machine group configuration. Indexes are: - vmCurCfgGroupMacGroupIndex - group number - vmCurCfgGroupMacVMIndex - virtual machine con… |
| 1.3.6.1.4.1.26543.2.7.7.15.2.3.1.1 | ColumnvmCurCfgGroupMacGroupIndex | read-only | current | The group number for which the info is related. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.3.1.2 | ColumnvmCurCfgGroupMacVMIndex | read-only | current | The virtual machine number for which the info is related. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.3.1.3 | ColumnvmCurCfgGroupMacVMMac | read-only | current | virtual machine MAC address. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.4 | TablevmNewCfgGroupMacTable | not-accessible | current | virtual machine group new configuration table. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.4.1 | RowvmNewCfgGroupMaclistEntry | not-accessible | current | Information about virtual machine group |
| 1.3.6.1.4.1.26543.2.7.7.15.2.4.1.1 | ColumnvmNewCfgGroupMacGroupIndex | read-only | current | The group number for which the info is related. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.4.1.2 | ColumnvmNewCfgGroupMacVMIndex | read-only | current | The virtual machine number for which the info is related. |
| 1.3.6.1.4.1.26543.2.7.7.15.2.4.1.3 | ColumnvmNewCfgGroupMacVMMac | read-only | current | The virtual machine MAC address. |
| 1.3.6.1.4.1.26543.2.7.7.15.3 | NodevmPolicy | |||
| 1.3.6.1.4.1.26543.2.7.7.15.3.1 | Nodevmbw | |||
| 1.3.6.1.4.1.26543.2.7.7.15.3.1.1 | TablevmbwCurCfgTable | not-accessible | current | The table of current VM Bandwidth configuration. |
| 1.3.6.1.4.1.26543.2.7.7.15.3.1.1.1 | RowvmbwCurCfgEntry | not-accessible | current | A row in the current VM bandwidth table. |
| 1.3.6.1.4.1.26543.2.7.7.15.3.1.1.1.1 | ColumnvmbwCurCfgMac | read-only | current | MAC address of VM for which bandwidth control information is related. |
| 1.3.6.1.4.1.26543.2.7.7.15.3.1.1.1.2 | ColumnvmbwCurCfgTxRate | read-only | current | VM transmit bandwidth committed rate in kbps (ingress for switch). |
| 1.3.6.1.4.1.26543.2.7.7.15.3.1.1.1.3 | ColumnvmbwCurCfgTxBurst | read-only | current | VM transmit bandwidth max burst size in kilobits (ingress for switch). |
| 1.3.6.1.4.1.26543.2.7.7.15.3.1.1.1.4 | ColumnvmbwCurCfgTxAclId | read-only | current | ACL used for VM transmit bandwidth. |
| 1.3.6.1.4.1.26543.2.7.7.15.3.1.1.1.5 | ColumnvmbwCurCfgRxRate | read-only | current | VM receive bandwidth committed rate in kbps (egress for switch). |
| 1.3.6.1.4.1.26543.2.7.7.15.3.1.1.1.6 | ColumnvmbwCurCfgRxBurst | read-only | current | VM receive bandwidth max burst size in kilobits (egress for switch). |
| 1.3.6.1.4.1.26543.2.7.7.15.3.1.1.1.7 | ColumnvmbwCurCfgCtrl | read-only | current | Enable/Disable VM bandwidth control entry. |
| 1.3.6.1.4.1.26543.2.7.7.15.3.1.2 | TablevmbwNewCfgTable | not-accessible | current | The table of new VM Bandwidth configuration. |
| 1.3.6.1.4.1.26543.2.7.7.15.3.1.2.1 | RowvmbwNewCfgEntry | not-accessible | current | A row in the new VM bandwidth table. |
| 1.3.6.1.4.1.26543.2.7.7.15.3.1.2.1.1 | ColumnvmbwNewCfgMac | read-only | current | MAC address of VM for which bandwidth control information is related. |
| 1.3.6.1.4.1.26543.2.7.7.15.3.1.2.1.2 | ColumnvmbwNewCfgTxRate | read-write | current | VM transmit bandwidth committed rate in kbps (ingress for switch). Set this to zero to disable transmit bandwidth control. |
| 1.3.6.1.4.1.26543.2.7.7.15.3.1.2.1.3 | ColumnvmbwNewCfgTxBurst | read-write | current | VM transmit bandwidth max burst size in kilobits (ingress for switch). Set this to zero to disable transmit bandwidth control. |
| 1.3.6.1.4.1.26543.2.7.7.15.3.1.2.1.4 | ColumnvmbwNewCfgTxAclId | read-write | current | ACL used for VM transmit bandwidth. This is optional parameter. If set to zero the system will choose one ACL for tx bandwidth control. |
| 1.3.6.1.4.1.26543.2.7.7.15.3.1.2.1.5 | ColumnvmbwNewCfgRxRate | read-write | current | VM receive bandwidth committed rate in kbps (egress for switch). Set this to zero to disable receive bandwidth control. |
| 1.3.6.1.4.1.26543.2.7.7.15.3.1.2.1.6 | ColumnvmbwNewCfgRxBurst | read-write | current | VM receive bandwidth max burst size in kilobits (egress for switch). Set this to zero to disable receive bandwidth control. |
| 1.3.6.1.4.1.26543.2.7.7.15.3.1.2.1.7 | ColumnvmbwNewCfgCtrl | read-write | current | VM bandwidth control entry status |
| 1.3.6.1.4.1.26543.2.7.7.15.3.1.2.1.8 | ColumnvmbwNewCfgDelete | read-write | current | This is an action object to delete a VM Bandwidth entry. other(1) is returned always when read. To delete an entry enter delete(2). |
| 1.3.6.1.4.1.26543.2.7.7.15.4 | NodevmProfiles | |||
| 1.3.6.1.4.1.26543.2.7.7.15.4.1 | TablevmCurCfgProfilesTable | not-accessible | current | The table of VM profiles in the current config |
| 1.3.6.1.4.1.26543.2.7.7.15.4.1.1 | RowvmCurCfgProfileEntry | not-accessible | current | Information about a VM profile in current config. |
| 1.3.6.1.4.1.26543.2.7.7.15.4.1.1.1 | ColumnvmCurCfgProfileIndex | read-only | current | The index of the vm profiles table (1..32). |
| 1.3.6.1.4.1.26543.2.7.7.15.4.1.1.2 | ColumnvmCurCfgProfileName | read-only | current | VM Profile name. |
| 1.3.6.1.4.1.26543.2.7.7.15.4.1.1.3 | ColumnvmCurCfgProfileVlan | read-only | current | Current VM Profile VLAN Id |
| 1.3.6.1.4.1.26543.2.7.7.15.4.1.1.4 | ColumnvmCurCfgProfileShapingAverage | read-only | current | Current VM Profile Shaping Average. |
| 1.3.6.1.4.1.26543.2.7.7.15.4.1.1.5 | ColumnvmCurCfgProfileShapingBurst | read-only | current | Current VM Profile Shaping Burst. |
| 1.3.6.1.4.1.26543.2.7.7.15.4.1.1.6 | ColumnvmCurCfgProfileShapingPeak | read-only | current | Current VM Profile Shaping Peak. |
| 1.3.6.1.4.1.26543.2.7.7.15.4.1.1.7 | ColumnvmCurCfgProfileEgressShapingAverage | read-only | current | Current VM Profile Egress Shaping Average. |
| 1.3.6.1.4.1.26543.2.7.7.15.4.1.1.8 | ColumnvmCurCfgProfileEgressShapingBurst | read-only | current | Current VM Profile Egress Shaping Burst. |
| 1.3.6.1.4.1.26543.2.7.7.15.4.1.1.9 | ColumnvmCurCfgProfileEgressShapingPeak | read-only | current | Current VM Profile Egress Shaping Peak. |
| 1.3.6.1.4.1.26543.2.7.7.15.4.2 | TablevmNewCfgProfilesTable | not-accessible | current | The table of VM profiles in the current config |
| 1.3.6.1.4.1.26543.2.7.7.15.4.2.1 | RowvmNewCfgProfileEntry | not-accessible | current | Information about a VM profile in current config. |
| 1.3.6.1.4.1.26543.2.7.7.15.4.2.1.1 | ColumnvmNewCfgProfileIndex | read-only | current | The index of the vm profiles table (1..32). |
| 1.3.6.1.4.1.26543.2.7.7.15.4.2.1.2 | ColumnvmNewCfgProfileName | read-write | current | VM Profile name. |
| 1.3.6.1.4.1.26543.2.7.7.15.4.2.1.3 | ColumnvmNewCfgProfileVlan | read-write | current | Vlan to be used by the VM profile. |
| 1.3.6.1.4.1.26543.2.7.7.15.4.2.1.4 | ColumnvmNewCfgProfileShapingAverage | read-write | current | Shaping average to be used by the VM profile. |
| 1.3.6.1.4.1.26543.2.7.7.15.4.2.1.5 | ColumnvmNewCfgProfileShapingBurst | read-write | current | Shaping burst to be used by the VM profile. |
| 1.3.6.1.4.1.26543.2.7.7.15.4.2.1.6 | ColumnvmNewCfgProfileShapingPeak | read-write | current | Shaping peak to be used by the VM profile. |
| 1.3.6.1.4.1.26543.2.7.7.15.4.2.1.7 | ColumnvmNewCfgProfileDelete | read-write | current | Delete VM Profile. |
| 1.3.6.1.4.1.26543.2.7.7.15.4.2.1.8 | ColumnvmNewCfgProfileEgressShapingAverage | read-write | current | Egress shaping average to be used by the VM profile. |
| 1.3.6.1.4.1.26543.2.7.7.15.4.2.1.9 | ColumnvmNewCfgProfileEgressShapingBurst | read-write | current | Egress shaping burst to be used by the VM profile. |
| 1.3.6.1.4.1.26543.2.7.7.15.4.2.1.10 | ColumnvmNewCfgProfileEgressShapingPeak | read-write | current | Egress shaping peak to be used by the VM profile. |
| 1.3.6.1.4.1.26543.2.7.7.15.5 | NodevirtVMware | |||
| 1.3.6.1.4.1.26543.2.7.7.15.5.1 | ScalarvirtVMwareNameTableUpdate | read-write | current | This is an action object to get information from the Virtual Center. Set this value to get(2) to update the host and VM name tables: virtVMwareHostNameTable, v… |
| 1.3.6.1.4.1.26543.2.7.7.15.5.2 | TablevirtVMwareHostNameTable | not-accessible | current | The table of names of VMware hosts in the Virtual Center. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.2.1 | RowvirtVMwareHostNameEntry | not-accessible | current | Information about names of VMware hosts in the Data Center. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.2.1.1 | ColumnvirtVMwareHostNameIndex | read-only | current | The index of the virtVMwareHostNameTable table. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.2.1.2 | ColumnvirtVMwareHostNameUUID | read-only | current | The UUID of a VMware host. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.2.1.3 | ColumnvirtVMwareHostNameIpAddress | read-only | current | The IP address of a VMware host. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.2.1.4 | ColumnvirtVMwareHostNameName | read-only | current | The name of a VMware host. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.3 | TablevirtVMwareVMNameTable | not-accessible | current | The table of VMware virtual machines in the Data Center. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.3.1 | RowvirtVMwareVMNameEntry | not-accessible | current | Information about VMware virtual machines in the Data Center. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.3.1.1 | ColumnvirtVMwareVMNameIndex | read-only | current | The index of the VMware virtual machine table in the Data Center. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.3.1.2 | ColumnvirtVMwareVMNameUUID | read-only | current | The UUID of a virtual machine. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.3.1.3 | ColumnvirtVMwareVMNameVMwareName | read-only | current | The name of a virtual machine given by VMware. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.3.1.4 | ColumnvirtVMwareVMNameOsName | read-only | current | The name of a virtual machine given by the host OS. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.3.1.5 | ColumnvirtVMwareVMNameIpAddress | read-only | current | The IP address of a virtual machine. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.4 | ScalarvirtVMwareHost | read-write | current | VMware host ID This is an action object to get information about a specific host from the Virtual Center. This object specifies the host ID by UUID / IP Addres… |
| 1.3.6.1.4.1.26543.2.7.7.15.5.5 | TablevirtVMwareHostVswitchTable | not-accessible | current | The table of Vswitches available on the specified host. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.5.1 | RowvirtVMwareHostVswitchEntry | not-accessible | current | Information about Vswitches available on the specified host. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.5.1.1 | ColumnvirtVMwareHostVswitchIndex | read-only | current | The index of the Vswitch table on the specified host. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.5.1.2 | ColumnvirtVMwareHostVswitchName | read-only | current | The name of a Vswitch on the specified host. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.6 | TablevirtVMwareHostPGTable | not-accessible | current | The table of Port Groups available on the specified host. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.6.1 | RowvirtVMwareHostPGEntry | not-accessible | current | Information about Port Groups available on the specified host. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.6.1.1 | ColumnvirtVMwareHostPGIndex | read-only | current | The index of the Port Group table on the specified host. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.6.1.2 | ColumnvirtVMwareHostPGName | read-only | current | The name of a Port Group on the specified host. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.6.1.3 | ColumnvirtVMwareHostPGVswitchName | read-only | current | The name of a Vswitch on the specified host. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.7 | TablevirtVMwareHostDetailInfoTable | not-accessible | current | The table of detailed information available on the specified host/VM interface. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.7.1 | RowvirtVMwareHostDetailInfoEntry | not-accessible | current | Detailed information available on the specified host/VM interface. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.7.1.1 | ColumnvirtVMwareHostDetailInfoIndex | read-only | current | The index of the detailed information table on the specified host/VM interface. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.7.1.2 | ColumnvirtVMwareHostDetailInfoMACAddr | read-only | current | The MAC address of the host/VM interface. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.7.1.3 | ColumnvirtVMwareHostDetailInfoPortIdx | read-only | current | The port number of the specified host/VM interface. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.7.1.4 | ColumnvirtVMwareHostDetailInfoType | read-only | current | Interface type |
| 1.3.6.1.4.1.26543.2.7.7.15.5.7.1.5 | ColumnvirtVMwareHostDetailInfoIPAddr | read-only | current | The IP address of the specified host/VM interface. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.7.1.6 | ColumnvirtVMwareHostDetailInfoUUID | read-only | current | The UUID of the specified host/VM interface. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.7.1.7 | ColumnvirtVMwareHostDetailInfoVswitch | read-only | current | The name of the virtual switch of the specified host/VM interface. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.7.1.8 | ColumnvirtVMwareHostDetailInfoPortGroup | read-only | current | The name of the port group of the specified host/VM interface. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.7.1.9 | ColumnvirtVMwareHostDetailInfoVlanID | read-only | current | The VLAN ID of the specified host/VM interface. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.7.1.10 | ColumnvirtVMwareHostDetailInfoHostName | read-only | current | The name of the specified host interface. N/A for VMs. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.7.1.11 | ColumnvirtVMwareHostDetailInfoVMVCenterName | read-only | current | The name of the Virtual Center of the specified VM interface. N/A for host interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.7.1.12 | ColumnvirtVMwareHostDetailInfoVMOSHostName | read-only | current | The name of the VM set by the host operating system. N/A for host interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.7.1.13 | ColumnvirtVMwareHostDetailInfoVMCurrentHost | read-only | current | The name of the host of the specified VM. N/A for host interfaces. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.8 | ScalarvirtVMwareVM | read-write | current | VMware virtual machine ID This is an action object to get information about a specific virtual machine from the Virtual Center. This object specifies the VM ID… |
| 1.3.6.1.4.1.26543.2.7.7.15.5.9 | TablevirtVMwareVMInfoTable | not-accessible | current | The table of networking information available on the specified VM. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.9.1 | RowvirtVMwareVMInfoEntry | not-accessible | current | Detailed information available on the specified VM. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.9.1.1 | ColumnvirtVMwareVMInfoIndex | read-only | current | The index of the table with information on the specified VM. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.9.1.2 | ColumnvirtVMwareVMInfoMACAddr | read-only | current | The MAC address of the specified VM. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.9.1.3 | ColumnvirtVMwareVMInfoPortIdx | read-only | current | The port number of the specified VM. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.9.1.4 | ColumnvirtVMwareVMInfoType | read-only | current | Interface type |
| 1.3.6.1.4.1.26543.2.7.7.15.5.9.1.5 | ColumnvirtVMwareVMInfoIPAddr | read-only | current | The IP address of the specified VM. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.9.1.6 | ColumnvirtVMwareVMInfoUUID | read-only | current | The UUID of the specified VM. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.9.1.7 | ColumnvirtVMwareVMInfoVswitch | read-only | current | The name of the virtual switch of the specified VM. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.9.1.8 | ColumnvirtVMwareVMInfoPortGroup | read-only | current | The name of the port group of the specified VM. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.9.1.9 | ColumnvirtVMwareVMInfoVlanID | read-only | current | The VLAN ID of the specified VM. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.9.1.10 | ColumnvirtVMwareVMInfoVMVCenterName | read-only | current | The name of the Virtual Center of the specified VM. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.9.1.11 | ColumnvirtVMwareVMInfoVMOSHostName | read-only | current | The name of the VM set by the host operating system. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.9.1.12 | ColumnvirtVMwareVMInfoVMCurrentHost | read-only | current | The name of the host of the specified VM. |
| 1.3.6.1.4.1.26543.2.7.7.15.5.10 | NodevirtCurCfgVMwareHello | |||
| 1.3.6.1.4.1.26543.2.7.7.15.5.10.1 | ScalarvirtCurCfgVMwareHelloEnable | read-only | current | Current value for hello advertising status |
| 1.3.6.1.4.1.26543.2.7.7.15.5.10.2 | ScalarvirtCurCfgVMwareHelloTimer | read-only | current | Current hello packet send interval |
| 1.3.6.1.4.1.26543.2.7.7.15.5.10.3 | ScalarvirtCurCfgVMwareHelloPorts | read-only | current | Current value for the configured hello port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... |… |
| 1.3.6.1.4.1.26543.2.7.7.15.5.10.4 | ScalarvirtCurCfgVMwareHelloAddr | read-only | current | Current VM hello IP address |
| 1.3.6.1.4.1.26543.2.7.7.15.5.11 | NodevirtNewCfgVMwareHello | |||
| 1.3.6.1.4.1.26543.2.7.7.15.5.11.1 | ScalarvirtNewCfgVMwareHelloEnable | read-write | current | New value for hello advertising status |
| 1.3.6.1.4.1.26543.2.7.7.15.5.11.2 | ScalarvirtNewCfgVMwareHelloTimer | read-write | current | New hello packet send interval |
| 1.3.6.1.4.1.26543.2.7.7.15.5.11.3 | ScalarvirtNewCfgVMwareHelloPorts | read-only | current | New value for the configured hello port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || ||… |
| 1.3.6.1.4.1.26543.2.7.7.15.5.11.4 | ScalarvirtNewCfgVMwareHelloAddPortIdx | read-write | current | Add a port to the hello port list |
| 1.3.6.1.4.1.26543.2.7.7.15.5.11.5 | ScalarvirtNewCfgVMwareHelloRemovePortIdx | read-write | current | Remove a port from the hello port list |
| 1.3.6.1.4.1.26543.2.7.7.15.5.11.6 | ScalarvirtNewCfgVMwareHelloAddr | read-write | current | New VM hello IP address |
| 1.3.6.1.4.1.26543.2.7.7.15.6 | Nodeevb | |||
| 1.3.6.1.4.1.26543.2.7.7.15.6.1 | NodeevbConfig | |||
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.3 | TableevbCurCfgProfilesTable | not-accessible | current | The table of EVB Profiles in the current config |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.3.1 | RowevbCurCfgProfileEntry | not-accessible | current | Information about EVB Profile in current config. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.3.1.1 | ColumnevbCurCfgProfileIndex | read-only | current | The index of the evb profile table. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.3.1.2 | ColumnevbCurCfgRR | read-only | current | Enable RR on port. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.3.1.3 | ColumnevbCurCfgVSIDisc | read-only | current | Enable VSI Discover capability on port. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.4 | TableevbNewCfgProfilesTable | not-accessible | current | The table of EVB Profiles in the new config |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.4.1 | RowevbNewCfgProfileEntry | not-accessible | current | Information about EVB Profile in new config. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.4.1.1 | ColumnevbNewCfgProfileIndex | read-only | current | The index of the evb profile table. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.4.1.2 | ColumnevbNewCfgRR | read-write | current | Enable RR on port. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.4.1.3 | ColumnevbNewCfgVSIDisc | read-write | current | Enable VSI Discover capability on port. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.5 | TableevbCurCfgVsidbTable | not-accessible | current | The table of EVB VSI Database server in the current config |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.5.1 | RowevbCurCfgVsidbEntry | not-accessible | current | Information about EVB VSI Database in current config. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.5.1.1 | ColumnevbCurCfgVsidbIndex | read-only | current | The index of the evb vsi database server table. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.5.1.2 | ColumnevbCurCfgVsidbMgrIp | read-only | current | VSI DB Manager IP address. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.5.1.3 | ColumnevbCurCfgVsidbPort | read-only | current | VSI DB Manager Port. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.5.1.4 | ColumnevbCurCfgVsidbDocpath | read-only | current | VSI DB Document Path. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.5.1.5 | ColumnevbCurCfgVsidbAlltypes | read-only | current | VSI DB Document File. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.5.1.6 | ColumnevbCurCfgVsidbInterval | read-only | current | VSI DB Update Interval in second. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.5.1.8 | ColumnevbCurCfgVsidbProtocol | read-only | current | VSI DB Protocol, HTTP or HTTPS. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.6 | TableevbNewCfgVsidbTable | not-accessible | current | The table of EVB VSI Database in the new config |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.6.1 | RowevbNewCfgVsidbEntry | not-accessible | current | Information about EVB VSI Database in new config. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.6.1.1 | ColumnevbNewCfgVsidbIndex | read-only | current | The index of the evb vsi database server table. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.6.1.2 | ColumnevbNewCfgVsidbMgrIp | read-write | current | VSI DB Manager IP address. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.6.1.3 | ColumnevbNewCfgVsidbPort | read-write | current | VSI DB Manager Port. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.6.1.4 | ColumnevbNewCfgVsidbDocpath | read-write | current | VSI DB Document Path. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.6.1.5 | ColumnevbNewCfgVsidbAlltypes | read-write | current | VSI DB Document File. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.6.1.6 | ColumnevbNewCfgVsidbInterval | read-write | current | VSI DB Update Interval in second, range from 5s to 300s, 0 means disable auto update. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.1.6.1.8 | ColumnevbNewCfgVsidbProtocol | read-write | current | VSI DB Protocol, HTTP or HTTPS. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2 | NodeevbInfo | |||
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1 | TablevdpTLVInfoTable | not-accessible | current | The table of associated VDP TLV Info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1 | RowvdpTLVInfoEntry | not-accessible | current | Information about associated VDP TLV. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.1 | ColumnvdpTLVInfoEntryIndex | read-only | current | The index of the vdp TLV info table. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.2 | ColumnvdpTLVType | read-only | current | The vdp TLV Type info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.3 | ColumnvdpTLVLength | read-only | current | The vdp TLV Length info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.4 | ColumnvdpTLVOUI | read-only | current | The vdp TLV OUI info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.5 | ColumnvdpTLVsubType | read-only | current | The vdp TLV Sub Type info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.6 | ColumnvdpTLVRequest | read-only | current | The vdp TLV Request info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.7 | ColumnvdpTLVResp | read-only | current | The vdp TLV Response info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.8 | ColumnvdpTLVMgrId | read-only | current | The vdp TLV Manager ID info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.9 | ColumnvdpTLVTypeID | read-only | current | The vdp TLV Type ID info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.10 | ColumnvdpTLVInstanceID | read-only | current | The vdp TLV instance ID info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.11 | ColumnvdpTLVPort | read-only | current | The vdp TLV port info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.12 | ColumnvdpTLVStag | read-only | current | The vdp TLV stag info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.13 | ColumnvdpNumEntry | read-only | current | The vdp TLV vlan info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.14 | ColumnvdpTLVVlan1 | read-only | current | The vdp TLV vlan info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.15 | ColumnvdpTLVmac1 | read-only | current | The vdp TLV mac info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.16 | ColumnvdpTLVVlan2 | read-only | current | The vdp TLV vlan info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.17 | ColumnvdpTLVmac2 | read-only | current | The vdp TLV mac info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.18 | ColumnvdpTLVVlan3 | read-only | current | The vdp TLV vlan info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.19 | ColumnvdpTLVmac3 | read-only | current | The vdp TLV mac info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.20 | ColumnvdpTLVVlan4 | read-only | current | The vdp TLV vlan info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.21 | ColumnvdpTLVmac4 | read-only | current | The vdp TLV mac info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.22 | ColumnvdpTLVVlan5 | read-only | current | The vdp TLV vlan info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.23 | ColumnvdpTLVmac5 | read-only | current | The vdp TLV mac info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.24 | ColumnvdpTLVVlan6 | read-only | current | The vdp TLV vlan info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.25 | ColumnvdpTLVmac6 | read-only | current | The vdp TLV mac info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.26 | ColumnvdpTLVVlan7 | read-only | current | The vdp TLV vlan info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.27 | ColumnvdpTLVmac7 | read-only | current | The vdp TLV mac info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.28 | ColumnvdpTLVVlan8 | read-only | current | The vdp TLV vlan info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.29 | ColumnvdpTLVmac8 | read-only | current | The vdp TLV mac info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.30 | ColumnvdpTLVVlan9 | read-only | current | The vdp TLV vlan info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.31 | ColumnvdpTLVmac9 | read-only | current | The vdp TLV mac info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.32 | ColumnvdpTLVVlan10 | read-only | current | The vdp TLV vlan info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.33 | ColumnvdpTLVmac10 | read-only | current | The vdp TLV mac info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.34 | ColumnvdpTLVVlan11 | read-only | current | The vdp TLV vlan info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.35 | ColumnvdpTLVmac11 | read-only | current | The vdp TLV mac info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.36 | ColumnvdpTLVVlan12 | read-only | current | The vdp TLV vlan info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.1.1.37 | ColumnvdpTLVmac12 | read-only | current | The vdp TLV mac info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.2 | TablevmsInfoTable | not-accessible | current | The table of active VM Info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.2.1 | RowvmsInfoEntry | not-accessible | current | Information about active VMs. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.2.1.1 | ColumnvmsInfoEntryIndex | read-only | current | The index of the active VM info table. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.2.1.2 | ColumnvmsInfoTypeId | read-only | current | The VSI Type ID info of the active VM |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.2.1.3 | ColumnvmsInfoVersion | read-only | current | The VSI Type version info of the active VM |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.2.1.4 | ColumnvmsInfoMac | read-only | current | The VSI Mac info of the active VM |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.2.1.5 | ColumnvmsInfoVlan | read-only | current | The VSI vlan info of the active VM |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.2.1.6 | ColumnvmsInfoPortIdx | read-only | current | The VSI port info of the active VM |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.2.1.7 | ColumnvmsInfoTxACL | read-only | current | The VSI Tx ACL info of the active VM |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.2.1.8 | ColumnvmsInfoRxEntry | read-only | current | The VSI Rx info of the active VM |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.2.1.9 | ColumnvmsInfoACLs | read-only | current | The ACL info of the active VM |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.3 | TablevsiInfoTable | not-accessible | current | The table of vsi policy Info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.3.1 | RowvsiInfoEntry | not-accessible | current | Information about vsi policy. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.3.1.1 | ColumnvsiInfoEntryIndex | read-only | current | The index of the vsi info table. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.3.1.2 | ColumnvsiInfoTypeId | read-only | current | The VSI Type ID info |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.3.1.3 | ColumnvsiInfoVersion | read-only | current | The VSI Type version info |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.3.1.4 | ColumnvsiInfoMac | read-only | current | The VSI Mac Info |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.3.1.5 | ColumnvsiInfoVlan | read-only | current | The VSI vlan info |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.3.1.6 | ColumnvsiInfoPortIdx | read-only | current | The VSI port info |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.3.1.7 | ColumnvsiInfoTxACL | read-only | current | The VSI Tx ACL info |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.3.1.8 | ColumnvsiInfoRxEntry | read-only | current | The VSI Rx info |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.4 | TablevsidbInfoTable | not-accessible | current | The table of VSI Database Info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.4.1 | RowvsidbInfoEntry | not-accessible | current | Information about VSI database |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.4.1.1 | ColumnvsidbInfoEntryIndex | read-only | current | The index of the VSI Database table. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.4.1.2 | ColumnvsidbInfoName | read-only | current | VSI Database Name. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.4.1.3 | ColumnvsidbInfoTypeId | read-only | current | VSI Database Type Id. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.4.1.4 | ColumnvsidbInfoVersion | read-only | current | VSI Database Version. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.4.1.5 | ColumnvsidbInfoManagerId | read-only | current | VSI Database Manager Id. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.4.1.6 | ColumnvsidbInfoVlanIds | read-only | current | VSI Database VLAN List. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.4.1.7 | ColumnvsidbInfoTxRate | read-only | current | VSI Database Transmit Rate. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.4.1.8 | ColumnvsidbInfoTxBurst | read-only | current | VSI Database Transmit Burst. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.4.1.9 | ColumnvsidbInfoRxRate | read-only | current | VSI Database Receive Rate. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.4.1.10 | ColumnvsidbInfoRxBurst | read-only | current | VSI Database Receove Burst. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5 | TablevsidbAclInfoTable | not-accessible | current | The table of VSI Database ACLs Info. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1 | RowvsidbAclInfoEntry | not-accessible | current | Information about VSI database |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.1 | ColumnvsidbAclInfoEntryDbIndex | read-only | current | The index of the VSI Database table. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.2 | ColumnvsidbAclInfoEntryAclIndex | read-only | current | The index of the VSI Database ACLs table. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.3 | ColumnvsidbAclInfoTypeId | read-only | current | VSI Database Type Id. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.4 | ColumnvsidbAclInfoVersion | read-only | current | VSI Database Version. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.5 | ColumnvsidbAclInfoManagerId | read-only | current | VSI Database Manager Id. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.6 | ColumnvsidbAclInfoSrcMACAddress | read-only | current | VSI Database ACL Source MAC address. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.7 | ColumnvsidbAclInfoSrcMACMask | read-only | current | VSI Database ACL Source MAC address mask. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.8 | ColumnvsidbAclInfoDstMACAddress | read-only | current | VSI Database ACL Destination MAC address. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.9 | ColumnvsidbAclInfoDstMACMask | read-only | current | VSI Database ACL Destination MAC address mask. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.10 | ColumnvsidbAclInfoVlanId | read-only | current | VSI Database ACL Virtual LAN value. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.13 | ColumnvsidbAclInfoEthernetType | read-only | current | VSI Database ACL Ethernet type value, 'none' for not initialised, within the ranger 1536-65535. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.14 | ColumnvsidbAclInfoSrcIPAddress | read-only | current | VSI Database ACL Source IP Address, only available when EthernetType is IPv4(0x0800). |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.15 | ColumnvsidbAclInfoSrcIPMask | read-only | current | VSI Database ACL Source IP Address mask, only available when EthernetType is IPv4(0x0800). |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.16 | ColumnvsidbAclInfoDstIPAddress | read-only | current | VSI Database ACL Destination IP Address, only available when EthernetType is IPv4(0x0800). |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.17 | ColumnvsidbAclInfoDstIPMask | read-only | current | VSI Database ACL Destination IP Address mask, only available when EthernetType is IPv4(0x0800). |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.18 | ColumnvsidbAclInfoTypeOfService | read-only | current | VSI Database ACL Type Of Service value, only available when EthernetType is IPv4(0x0800), 'none' for not initialised, within the ranger 0-255. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.19 | ColumnvsidbAclInfoProtocol | read-only | current | VSI Database ACL IP protocol, only available when EthernetType is IPv4(0x0800), 'none' for not initialised, within the ranger 0-255. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.20 | ColumnvsidbAclInfoTCPFlags | read-only | current | VSI Database ACL TCP Flags value, only available when EthernetType is IPv4(0x0800) and Protocol is TCP(6). |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.21 | ColumnvsidbAclInfoTCPFlagsMask | read-only | current | VSI Database ACL TCP Flags mask, only available when EthernetType is IPv4(0x0800) and Protocol is TCP(6). |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.22 | ColumnvsidbAclInfoSrcPort | read-only | current | VSI Database ACL Source TCP/UDP Port value, only available when EthernetType is IPv4(0x0800) and Protocol is TCP(6) or UDP(17). |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.23 | ColumnvsidbAclInfoSrcPortMask | read-only | current | VSI Database ACL Source TCP/UDP Port mask, only available when EthernetType is IPv4(0x0800) and Protocol is TCP(6) or UDP(17). |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.24 | ColumnvsidbAclInfoDstPort | read-only | current | VSI Database ACL Destination TCP/UDP Port value, only available when EthernetType is IPv4(0x0800) and Protocol is TCP(6) or UDP(17). |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.25 | ColumnvsidbAclInfoDstPortMask | read-only | current | VSI Database ACL Destination TCP/UDP Port mask, only available when EthernetType is IPv4(0x0800) and Protocol is TCP(6) or UDP(17). |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.26 | ColumnvsidbAclInfoAction | read-only | current | VSI Database ACL Action |
| 1.3.6.1.4.1.26543.2.7.7.15.6.2.5.1.27 | ColumnvsidbAclInfoNewPrio | read-only | current | VSI Database ACL New Pirority value, only available when Action includes 'setpriority', 'none' for not initialised. |
| 1.3.6.1.4.1.26543.2.7.7.15.6.3 | NodeevbOper | |||
| 1.3.6.1.4.1.26543.2.7.7.15.6.3.1 | ScalarevbVsidbOper | read-write | current | When set to 'update(2)', it downloads the xml file from VSIDB server and update local VSI database; when set to 'clean(3)', it cleans local VSI database; 'ok(1… |
| 1.3.6.1.4.1.26543.2.7.7.15.6.3.2 | ScalarevbAssocVsiClean | read-write | current | When set to 'clean(2)', it cleans all associated VSIs; 'ok(1)' is returned when the object is read. |
| 1.3.6.1.4.1.26543.2.7.7.15.7 | NodevmCheck | |||
| 1.3.6.1.4.1.26543.2.7.7.15.7.1 | NodevmCurCfgCheck | |||
| 1.3.6.1.4.1.26543.2.7.7.15.7.1.1 | ScalarvmCurCfgCheckActionBasic | read-only | current | Current settings for basic checking mode |
| 1.3.6.1.4.1.26543.2.7.7.15.7.1.2 | ScalarvmCurCfgCheckActionAdvanced | read-only | current | Current settings for advanced checking mode |
| 1.3.6.1.4.1.26543.2.7.7.15.7.1.3 | ScalarvmCurCfgCheckAclsMax | read-only | current | Current value for the maximum number of ACLs that can be used by Mac Spoofing Check feature |
| 1.3.6.1.4.1.26543.2.7.7.15.7.1.4 | ScalarvmCurCfgCheckTrust | read-only | current | Current value for the configured trusted port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx .....… |
| 1.3.6.1.4.1.26543.2.7.7.15.7.2 | NodevmNewCfgCheck | |||
| 1.3.6.1.4.1.26543.2.7.7.15.7.2.1 | ScalarvmNewCfgCheckActionBasic | read-write | current | New settings for basic checking mode |
| 1.3.6.1.4.1.26543.2.7.7.15.7.2.2 | ScalarvmNewCfgCheckActionAdvanced | read-write | current | New settings for advanced checking mode |
| 1.3.6.1.4.1.26543.2.7.7.15.7.2.3 | ScalarvmNewCfgCheckAclsMax | read-write | current | New value for the maximum number of ACLs that can be used by Mac Spoofing Check feature |
| 1.3.6.1.4.1.26543.2.7.7.15.7.2.4 | ScalarvmNewCfgCheckTrust | read-only | current | New value for the configured trusted port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || … |
| 1.3.6.1.4.1.26543.2.7.7.15.7.2.5 | ScalarvmNewCfgCheckTrustAddPortIdx | read-write | current | Add port to the configured trusted port list. |
| 1.3.6.1.4.1.26543.2.7.7.15.7.2.6 | ScalarvmNewCfgCheckTrustRemPortIdx | read-write | current | Remove port from the configured trusted port list. |
| 1.3.6.1.4.1.26543.2.7.7.15.8 | NodevmReadyMisc | |||
| 1.3.6.1.4.1.26543.2.7.7.15.8.1 | ScalarvmReadyLocalAdmMac | read-write | current | Treat locally administred MAC address as VMs |
| 1.3.6.1.4.1.26543.2.7.7.15.8.2 | TablevmReadyCurCfgOuiTbl | not-accessible | current | The table of current VM Ready OUI configuration. |
| 1.3.6.1.4.1.26543.2.7.7.15.8.2.1 | RowvmReadyCurCfgOuiEntry | not-accessible | current | A row in the current VM Ready OUI table. |
| 1.3.6.1.4.1.26543.2.7.7.15.8.2.1.1 | ColumnvmReadyCurCfgOuiMacIdx | read-only | current | OUI of locally administred MAC address |
| 1.3.6.1.4.1.26543.2.7.7.15.8.2.1.2 | ColumnvmReadyCurCfgOuiMac | read-only | current | OUI of locally administred MAC address |
| 1.3.6.1.4.1.26543.2.7.7.15.8.2.1.3 | ColumnvmReadyCurCfgVendor | read-only | current | Vendor name of the OUI locally administred |
| 1.3.6.1.4.1.26543.2.7.7.15.8.3 | TablevmReadyNewCfgOuiTbl | not-accessible | current | The table of new VM Ready OUI configuration. |
| 1.3.6.1.4.1.26543.2.7.7.15.8.3.1 | RowvmReadyNewCfgOuiEntry | not-accessible | current | A row in the new VM Ready OUI table. |
| 1.3.6.1.4.1.26543.2.7.7.15.8.3.1.1 | ColumnvmReadyNewCfgOuiMacIdx | read-only | current | OUI of locally administred MAC address |
| 1.3.6.1.4.1.26543.2.7.7.15.8.3.1.2 | ColumnvmReadyNewCfgOuiMac | read-write | current | New OUI of locally administred MAC address Format xx:yy:zz |
| 1.3.6.1.4.1.26543.2.7.7.15.8.3.1.3 | ColumnvmReadyNewCfgVendor | read-write | current | Vendor name of the OUI locally administred |
| 1.3.6.1.4.1.26543.2.7.7.15.8.3.1.4 | ColumnvmReadyNewCfgDelete | read-write | current | If set the OUI of the locally administred MAC would be deleted |
| 1.3.6.1.4.1.26543.3 | IdentityibmGbTORG8052MIB | MIB for IBM Networking Operating System RackSwitch G8052 All Rights reserved DEVICE VERSION: 7.11.3.0 | ||
| 1.3.6.1.4.1.26543.100 | Nodeibmnos-BladeSwitch | |||
| 1.3.6.1.4.1.26543.100.27 | Nodeibmnoscfa | |||
| 1.3.6.1.4.1.26543.100.27.1 | Nodeif | |||
| 1.3.6.1.4.1.26543.100.27.1.4 | TableifMainTable | not-accessible | current | A list of all the interface entries in the system. This table contains objects which are applicable to all types of interfaces in the system. This table is a p… |
| 1.3.6.1.4.1.26543.100.27.1.4.1 | RowifMainEntry | not-accessible | current | An entry containing management information applicable to a particular interface. |
| 1.3.6.1.4.1.26543.100.27.1.4.1.1 | ColumnifMainIndex | not-accessible | current | A unique value, greater than zero, for each interface. This object is identical to the ifIndex of the standard MIB-2 ifTable. |
| 1.3.6.1.4.1.26543.100.27.1.4.1.9 | ColumnifMainPortName | read-write | current | This is used to assign a alias to a port |
| 1.3.6.1.4.1.26543.100.81 | Nodeibmnos | |||
| 1.3.6.1.4.1.26543.100.81.1 | NodeibmnosSystem | |||
| 1.3.6.1.4.1.26543.100.81.1.10 | ScalaribmnosConfigSaveOption | read-write | current | Specifies whether the configurations of the switch has to be saved or not. The value 'noSave' specifies that the configurations need not be saved. The value 'f… |
| 1.3.6.1.4.1.26543.100.81.1.12 | ScalaribmnosConfigSaveFileName | read-write | current | Name of the file in which the switch configurations are to be saved. This object is valid only if 'issConfigSaveOption' is chosen to be 'flashSave' or 'remoteS… |
| 1.3.6.1.4.1.26543.100.81.1.13 | ScalaribmnosInitiateConfigSave | read-write | current | When set as 'true' switch configurations save operation is initiated. As soon as the configuration save operation is completed, the value of this object revert… |
| 1.3.6.1.4.1.26543.100.81.1.14 | ScalaribmnosConfigSaveStatus | read-only | current | Status of configuration save operation. |
| 1.3.6.1.4.1.26543.100.81.1.15 | ScalaribmnosConfigRestoreOption | read-write | current | Specifies whether the switch configurations have to be restored or not. The value 'factory' specifies that the switch configurations need not be restored when … |
| 1.3.6.1.4.1.26543.100.81.1.26 | ScalaribmnosLoggingOption | read-write | current | The Logging option specifying whether the logging is to be done at console or to a file(system buffer) in the system. |
| 1.3.6.1.4.1.26543.100.81.1.32 | ScalaribmnosLoginAuthentication | read-write | current | The mechanism by which the user login to access the GUI for configuration has to be authenticated. Authentication is done either locally or in the remote side … |
| 1.3.6.1.4.1.26543.100.81.1.40 | ScalaribmnosConfigRestoreFileVersion | read-only | current | Config Restoration file version. This version will be compared in each reboot against version stored in restoration file. Restoration will occur only if the fi… |
| 1.3.6.1.4.1.26543.100.81.2 | NodeibmnosConfigControl | |||
| 1.3.6.1.4.1.26543.100.81.2.2 | TableibmnosPortCtrlTable | not-accessible | current | A table to control the port specific parameters of the device like speed, duplex mode, etc. |
| 1.3.6.1.4.1.26543.100.81.2.2.1 | RowibmnosPortCtrlEntry | not-accessible | current | An entry appears in this table for each interface in the system. Index to the table is the interface index of the port. |
| 1.3.6.1.4.1.26543.100.81.2.2.1.1 | ColumnibmnosPortCtrlIndex | not-accessible | current | Interface index of the port for which the configuration in this entry applies. |
| 1.3.6.1.4.1.26543.100.81.2.2.1.2 | ColumnibmnosPortCtrlMode | read-write | current | Speficies the mode in which the speed, duplex modes and flow control of the interface is determined. If set as 'auto', the hardware senses speed and negotiates… |
| 1.3.6.1.4.1.26543.100.81.2.2.1.3 | ColumnibmnosPortCtrlDuplex | read-write | current | Configures interface data transfer mode as full-duplex or half-duplex. This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'Por… |
| 1.3.6.1.4.1.26543.100.81.2.2.1.4 | ColumnibmnosPortCtrlSpeed | read-write | current | Configures interface speed. This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value … |
| 1.3.6.1.4.1.26543.100.81.2.2.1.5 | ColumnibmnosPortCtrlFlowControl | read-write | current | Enables / disables flow control for the interface. This object be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it… |
| 1.3.6.1.4.1.26543.100.100 | Nodetoraddon | |||
| 1.3.6.1.4.1.26543.100.100.2 | Nodecfa | |||
| 1.3.6.1.4.1.26543.100.100.2.1 | TableibmnosPortCfgTable | not-accessible | current | The table of port configuration in the new_configuration block. |
| 1.3.6.1.4.1.26543.100.100.2.1.1 | RowibmnosPortCfgTableEntry | not-accessible | current | A row in the port configuration table in the new_configuration block. |
| 1.3.6.1.4.1.26543.100.100.2.1.1.1 | ColumnibmnosPortCfgIndx | not-accessible | current | The index of the row in port configurations table. |
| 1.3.6.1.4.1.26543.100.100.2.1.1.2 | ColumnibmnosPortCfgVlanTag | read-write | current | VLAN tag configured for the port |
| 1.3.6.1.4.1.26543.100.100.7 | Nodesys | |||
| 1.3.6.1.4.1.26543.100.100.7.2 | ScalaragImageForNextReset | read-write | current | The software image to be booted from at next reset. The following values are writable: image1(2)...image 1 image2(3)...image 2 |
| 1.3.6.1.4.1.26543.100.100.13 | NodeibmnosFdb | |||
| 1.3.6.1.4.1.26543.100.100.13.5 | TableibmnosFdbTable | not-accessible | current | The table of FDB entries. |
| 1.3.6.1.4.1.26543.100.100.13.5.1 | RowibmnosFdbEntry | not-accessible | current | A row in the FDB table |
| 1.3.6.1.4.1.26543.100.100.13.5.1.1 | ColumnibmnosFdbVlan | not-accessible | current | The VLAN ID for the FDB entry. |
| 1.3.6.1.4.1.26543.100.100.13.5.1.2 | ColumnibmnosFdbMacAddr | not-accessible | current | The MAC address for the FDB entry. |
| 1.3.6.1.4.1.26543.100.100.13.5.1.3 | ColumnibmnosFdbMacAddrStr | read-only | current | The MAC address in hex format for the FDB entry. This node is added for display purpose. |
| 1.3.6.1.4.1.26543.100.100.13.5.1.4 | ColumnibmnosFdbVlanId | read-only | current | The VLAN ID for the FDB entry. This node is added for display purpose. |
| 1.3.6.1.4.1.26543.100.100.13.5.1.5 | ColumnibmnosFdbSrcPort | read-only | current | Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance has been seen. A… |
| 1.3.6.1.4.1.26543.100.100.13.5.1.6 | ColumnibmnosFdbSrcTrunk | read-only | current | Either the value '0', or the trunk number of the trunk on which a frame having a source address equal to the value of the corresponding instance has been seen.… |
| 1.3.6.1.4.1.26543.100.100.13.5.1.7 | ColumnibmnosFdbState | read-only | current | The state of the FDB entry. The meanings of the values are : unknown(1) : the MAC address has not yet been learned by the switch but has only been seen as a de… |
| 1.3.6.1.4.1.26543.100.100.13.5.1.10 | ColumnibmnosFdbStatus | read-only | current | '1' if it is permanent '0' if it is not permanent |
| 1.3.6.1.4.1.26543.100.100.13.5.1.11 | ColumnibmnosFdbClearMac | read-write | current | Setting this value to clear(2) clears the corresponding table entry in FDB. |
| 1.3.6.1.4.1.26543.100.100.14 | Nodetor-switch | |||
| 1.3.6.1.4.1.26543.100.100.14.1 | ScalarhardwarePartNumber | read-only | current | The hardware part number of the Blade Switch. |
| 1.3.6.1.4.1.26543.100.100.14.2 | ScalarhardwareRevision | read-only | current | The hardware revision. If the revision is not available, a zero length string should be returned. |
| 1.3.6.1.4.1.26543.100.100.14.3 | ScalarhardwareLastBoot | read-only | current | Reason of the last boot. |
| 1.3.6.1.4.1.26543.100.100.14.4 | ScalarhardwareMACAddress | read-only | current | The MAC address. |
| 1.3.6.1.4.1.26543.100.100.14.5 | ScalarhardwareSwitchRunningSwVersion | read-only | current | The switch software version. |
| 1.3.6.1.4.1.26543.100.100.14.6 | ScalarhardwareFlashConfiguration | read-only | current | The active flash configuration. |
| 1.3.6.1.4.1.26543.100.100.14.7 | ScalarhardwarePCBAPartNumber | read-only | current | The PCBA part number. |
| 1.3.6.1.4.1.26543.100.100.14.8 | ScalarhardwareFABNumber | read-only | current | FAB Number |
| 1.3.6.1.4.1.26543.100.100.14.9 | ScalarhardwareSerialNumber | read-only | current | The switch serial number. |
| 1.3.6.1.4.1.26543.100.100.14.10 | ScalarhardwareManufacturingDate | read-only | current | The date of manufacturing. |
| 1.3.6.1.4.1.26543.100.100.14.11 | ScalarhwTemperatureSensor1 | read-only | current | The temperature sensor 1. |
| 1.3.6.1.4.1.26543.100.100.14.12 | ScalarhwTemperatureSensor2 | read-only | current | The temperature sensor 2. |
| 1.3.6.1.4.1.26543.100.100.14.13 | ScalarhwTemperatureSensor3 | read-only | current | The temperature sensor 3. |
| 1.3.6.1.4.1.26543.100.100.14.14 | ScalarhwFan1RPMValue | read-only | current | The Fan 1 RPM value. |
| 1.3.6.1.4.1.26543.100.100.14.15 | ScalarhwFan2RPMValue | read-only | current | The Fan 2 RPM value. |
| 1.3.6.1.4.1.26543.100.100.14.16 | ScalarhwFan3RPMValue | read-only | current | The Fan 3 RPM value. |
| 1.3.6.1.4.1.26543.100.100.14.17 | ScalarhwFan4RPMValue | read-only | current | The Fan 4 RPM value. |
| 1.3.6.1.4.1.26543.100.100.14.18 | ScalarhwFan5RPMValue | read-only | current | The Fan 5 RPM value. |
| 1.3.6.1.4.1.26543.100.100.14.19 | ScalarhwBoardRevision | read-only | current | The Board revision number. |
| 1.3.6.1.4.1.26543.100.100.14.20 | ScalarhwPowerSupply1State | read-only | current | The Power Supply 1 state. |
| 1.3.6.1.4.1.26543.100.100.14.21 | ScalarhwPowerSupply2State | read-only | current | The Power Supply 2 state. |
| 1.3.6.1.4.1.26543.100.100.14.22 | TableibmnosSfpInfoTable | not-accessible | current | The table of external port SFP information. |
| 1.3.6.1.4.1.26543.100.100.14.22.1 | RowibmnosSfpInfoTableEntry | not-accessible | current | A row in the external port SFP information table. |
| 1.3.6.1.4.1.26543.100.100.14.22.1.1 | ColumnibmnosSfpInfoIndx | read-only | current | Sfp Info index (port number) |
| 1.3.6.1.4.1.26543.100.100.14.22.1.2 | ColumnibmnosSfpInfoDescription | read-only | current | Type Ethernet device (None(0), SFP(1), CX4(2), SFPplus(3), DAC(6)) |
| 1.3.6.1.4.1.26543.100.100.14.22.1.3 | ColumnibmnosSfpInfoSerialNumber | read-only | current | Serial Number. |
| 1.3.6.1.4.1.26543.100.100.14.22.1.4 | ColumnibmnosSfpInfoPartNumber | read-only | current | Part Number. |
| 1.3.6.1.4.1.26543.100.100.14.22.1.5 | ColumnibmnosSfpInfoHWRevision | read-only | current | Hardware Revision |
| 1.3.6.1.4.1.26543.100.100.14.24 | ScalarswImage1Version | read-only | current | Software image1 version |
| 1.3.6.1.4.1.26543.100.100.14.25 | ScalarswImage2Version | read-only | current | Software image2 version |
| 1.3.6.1.4.1.26543.100.100.14.26 | ScalarswBootVersion | read-only | current | Software boot version |
| 1.3.6.1.4.1.26543.100.100.14.27 | ScalarhwFan6RPMValue | read-only | current | The Fan 6 RPM value. |
| 1.3.6.1.4.1.26543.100.100.14.32 | ScalarhwTemperatureSensor4 | read-only | current | The temperature sensor 4. |
| 1.3.6.1.4.1.26543.100.100.14.33 | ScalarhwTemperatureSensor5 | read-only | current | The temperature sensor 5. |
| 1.3.6.1.4.1.26543.100.100.14.34 | ScalarhwTemperatureSensor6 | read-only | current | The temperature sensor 4. |
| 1.3.6.1.4.1.26543.100.100.14.35 | ScalarhwTemperatureSensor7 | read-only | current | The temperature sensor 7. |
| 1.3.6.1.4.1.26543.100.100.14.36 | ScalarhwTemperatureSensor8 | read-only | current | The temperature sensor 8. |
| 1.3.6.1.4.1.26543.100.100.14.37 | ScalarhwTemperatureSensor9 | read-only | current | The temperature sensor 9. It is deprecated. |
| 1.3.6.1.4.1.26543.100.100.14.38 | ScalarhwTemperatureSensor10 | read-only | current | The temperature sensor 10. It is deprecated. |
| 1.3.6.1.4.1.26543.100.100.14.39 | ScalarhwTemperatureSensor11 | read-only | current | The temperature sensor 11. It is deprecated. |
| 1.3.6.1.4.1.26543.100.100.14.40 | ScalarhwFan7RPMValue | read-only | current | The Fan 7 RPM value. |
| 1.3.6.1.4.1.26543.100.100.14.41 | ScalarhwFan8RPMValue | read-only | current | The Fan 8 RPM value. |
| 1.3.6.1.4.1.26543.100.100.14.42 | ScalarhwBootTime | read-only | current | The hardware system boot time . |
| 1.3.6.1.4.1.26543.100.100.17 | NodeibmnosBladeHarmony | |||
| 1.3.6.1.4.1.26543.100.100.17.1 | NodedataCollection | |||
| 1.3.6.1.4.1.26543.100.100.17.1.1 | ScalaribmnosPortTableMaxEnt | read-only | current | The maximum number of rows in the port configuration host table. |
| 1.3.6.1.4.1.26543.100.100.17.1.3 | ScalaribmnosImage1Ver | read-only | current | The version of the software image stored in image 1 storage in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available o… |
| 1.3.6.1.4.1.26543.100.100.17.1.4 | ScalaribmnosImage2Ver | read-only | current | The version of the software image stored in image 2 storage in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available o… |
| 1.3.6.1.4.1.26543.100.100.17.1.5 | ScalarhwSwitchSoftwareVersion | read-only | current | The switch software version. |
| 1.3.6.1.4.1.26543.100.100.17.1.6 | ScalarhwSerialNum | read-only | current | The switch serial number. |
| 1.3.6.1.4.1.26543.100.100.17.1.7 | ScalarhwManufacturingDate | read-only | current | The date of manufacturing. |
| 1.3.6.1.4.1.26543.100.100.17.1.8 | ScalaribmnosReset | read-write | current | This is an action object to reboot the agent. other(1) is returned always when read. |
| 1.3.6.1.4.1.26543.100.100.17.1.9 | ScalaribmnosBootVer | read-only | current | The version of the boot code in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available. |
| 1.3.6.1.4.1.26543.100.100.17.1.10 | ScalaribmnosConfigForNxtReset | read-write | current | The configuration information to be loaded from at next reset. The following values are writable: active(2)...active configuration block backup(3)...backup con… |
| 1.3.6.1.4.1.26543.100.100.17.1.11 | ScalaribmnosSoftwareVersion | read-only | current | The version of the software image that is currently running on the system in the form of 'major.minor.maintenance.bugfix'. A zero length string is returned if … |
| 1.3.6.1.4.1.26543.100.100.17.3 | NodeimageConfigTransfer | |||
| 1.3.6.1.4.1.26543.100.100.17.3.1 | ScalaragTftpServer | read-write | current | The TFTP server IP address or domain name. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| IPsecKeyString | OCTET STRING (SIZE (0..1024)) | current | Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - th… |
| PortNumber | Unsigned32 | current | Represents a port number of a switch. |
| Timeout | Integer32 | current | Time out value in 4 byte |
| VlanId | Integer32 (1..4094) | current | A 12-bit VLAN ID used in the VLAN Tag header. |